Custom Board based on MX6 Dual, 1GB RAM and eMMC.
There are two variants of the board with and without
PCIe (ZC5202 and ZC5601).
Signed-off-by: Stefano Babic <sbabic@denx.de>
The SPL code already knows which boot device it calls the spl_boot_mode()
on, so pass that information into the function. This allows the code of
spl_boot_mode() avoid invoking spl_boot_device() again, but it also lets
board_boot_order() correctly alter the behavior of the boot process.
The later one is important, since in certain cases, it is desired that
spl_boot_device() return value be overriden using board_boot_order().
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
[add newly introduced zynq variant]
Signed-aff-by: Andreas Bießmann <andreas@biessmann.org>
The handling of the "usage counter" is incorrect, and the clock should
only be disabled when transitioning from 1 to 0.
Reported-by: Chris Brand <chris.brand@broadcom.com>
Signed-off-by: Steve Rae <srae@broadcom.com>
The Kona Peripheral Slave CCU has 4 policy mask registers, not 8.
Signed-off-by: Chris Brand <chris.brand@broadcom.com>
Signed-off-by: Steve Rae <srae@broadcom.com>
To make the PSCI backend more maintainable and easier to port to newer
SoCs, rewrite the current PSCI implementation in C.
Some inline assembly bits are required to access coprocessor registers.
PSCI stack setup is the only part left completely in assembly. In theory
this part could be split out of psci_arch_init into a separate common
function, and psci_arch_init could be completely in C.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Instead of hardcoding the GIC addresses in the PSCI implementation,
provide a base address in the cpu header.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Use SUNXI_CPUCFG_BASE across all families. This makes writing common
PSCI code easier.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
For psci_get_cpu_stack_top() to be usable in C code, it must adhere to
the ARM calling conventions. Since it could be called when the stack
is still unavailable, and the entry code to linux also expects r1 and
r2 to remain unchanged, stick to r0 and r3.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
board/am57xx supports all boards based on am57xx. Rename the taget
as TARGET_AM57XX_EVM.
Fixes: 74cc8b097d ("board: ti: beagle_x15: Rename to indicate support for TI am57xx evms")
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
At present CONFIG_SKIP_LOWLEVEL_INIT prevents U-Boot from calling
lowlevel_init(). This means that the instruction cache is not enabled and
the board runs very slowly.
What is really needed in many cases is to skip the call to lowlevel_init()
but still perform CP15 init. Add an option to handle this.
Reviewed-by: Heiko Schocher <hs@denx.de>
Tested-on: smartweb, corvus, taurus, axm
Tested-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Currently omap_vcores which holds pmic data is being assigned based
on the SoC type. PMIC is not a part of SoC. It is logical to
to assign omap_vcores based on board type. Hence over ride the
vcores_init function and assign omap_vcores based on the board type.
Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Enable Spread Spectrum for the MPU by calculating the required
values and setting the registers accordingly.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
The pmic registers for variants of am57xx boards are different
hence we need to assign them carefully based on the board type.
Add a function to assign omap_vcores after the board detection.
Signed-off-by: Keerthy <j-keerthy@ti.com>
The voltage values for each voltage domain at an OPP is identical
across all the SoCs in the DRA7 family. The current code defines
one set of macros for DRA75x/DRA74x SoCs and another set for DRA72x
macros. Consolidate both these sets into a single set.
This is done so as to minimize the number of macros used when voltage
values will be added for other OPPs as well.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Define a set of common macros for the efuse register offsets
(different for each OPP) that are used to get the AVS Class 0
voltage values and ABB configuration values. Assign these
common macros to the register offsets for OPP_NOM by default
for all voltage domains. These common macros can then be
redefined properly to point to the OPP specific efuse register
offset based on the desired OPP to program a specific voltage
domain.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
CONFIG_USB_XHCI_OMAP is enabled for host mode independent of CONFIG_USB_DWC3
which is meant for gadget mode only. We need enable/disbale_usb_clocks() for
host mode as well so provide for it.
Fixes: 09cc14f4bc ("ARM: AM43xx: Add functions to enable and disable USB clocks"
Signed-off-by: Roger Quadros <rogerq@ti.com>
All the output clock parameters of a DPLL needs to be programmed before
locking the DPLL. But it is being configured after locking the DPLL which
could potentially bypass DPLL. So fixing this sequence.
Reported-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
The CDCE913 and CDCEL913 devices are modular PLL-based, low cost,
high performance , programmable clock synthesizers. They generate
upto 3 output clocks from a single input frequency. Each output can
be programmed for any clock-frequency.
Adding support for the same.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Adds an fdt.c file in that defines the ft_cpu_setup() function,
which should be called from a board-specific ft_board_setup()).
This ft_cpu_setup() will currently do nothing for non-secure (GP)
devices but contains pertinent updates for booting on secure (HS)
devices.
Update the omap5 Makefile to include the fdt.c in the build.
Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Madan Srinivas <madans@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Update the CPU string output so that the device
type is now included as part of the CPU string that
is printed as the SPL or u-boot comes up. This update
adds a suffix of the form "-GP" or "-HS" for production
devices, so that general purpose (GP) and high security
(HS) can be distiguished. Applies to all OMAP5 variants.
Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Madan Srinivas <madans@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Updates the SPL build so that when CONFIG_TI_SECURE_DEVICE
is in use (which it should be when building for secure parts),
the TI secure development package is used to create a valid
secure boot image. The u-boot SPL build processes is NOT aware
of the details of creating the boot image - all of that information
is encapsulated in the TI secure development package, which is
available from TI. More info can be found in README.ti-secure
Right now, two image types are generated, MLO and X-LOADER. The types
are important, as certain boot modes implemented by the device's ROM
boot loader require one or the other (they are not equivalent). The
output filenames are u-boot-spl_HS_MLO and u-boot-spl_HS_X-LOADER. The
u-boot-spl_HS_MLO image is also copied to a file named MLO, which is
the name that the device ROM bootloader requires for loading from the
FAT partition of an SD card (same as on non-secure devices).
Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Madan Srinivas <madans@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Modifies the config.mk to build secure images when building
the SPL for secure devices.
Depending on the boot media, different images are needed
for secure devices. The build generates u-boot*_HS_* files
as appropriate for the different boot modes. The same u-boot
binary file is processed slightly differently to produce a
different boot image, depending on whether the user wants to
boot off SPI, QSPI or other boot media.
Refer to README.ti-secure for more information.
Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Daniel Allred <d-allred@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Adds a centralized config_secure.mk in omap-common for
OMAP-style TI secure devices to use for boot image generation
Depending on the boot media, different images are needed for
secure devices. These commands generates u-boot*_HS_* files that
need to be used to boot secure devices.
Please refer to README.ti-secure for more information.
Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Madan Srinivas <madans@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Defines CONFIG_TI_SECURE_DEVICE which needs to be turned on
when building images for secure devices. This flag is used
to invoke the secure image creation tools for creating a
boot image that can be used on secure devices. This flag
may also be used to conditionally compile code specific
to secure devices.
This terminology will be used by all OMAP architecture devices,
hence introducing to a common location.
With the creation of Kconfig for omap-common, moved the
sourcing of the Kconfig files for the omap3/4/5 and am33xx
devices from arch/arm/KConfig to the omap-common one.
Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Daniel Allred <d-allred@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Adding support for AM43xx secure devices require the addition
of some SOC specific config options like the amount of memory
used by public ROM and the address of the entry point of u-boot
or SPL, as seen by the ROM code, for the image to be built
correctly.
This mandates the addition of am AM43xx CONFIG option and the
ARM Kconfig file has been modified to source this SOC Kconfig
file. Moving the TARGET_AM43XX_EVM config option to the SOC
KConfig and out of the arch/arm/Kconfig.
Updating defconfigs to add the CONFIG_AM43XX=y statement and
removing the #define CONFIG_AM43XX from the header file.
Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Daniel Allred <d-allred@ti.com>
Tested-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Adds a new Kconfig file for AM33xx class devices. We
need a common place to define CONFIG parameters
for these SOCs, especially for adding support
for secure devices.
a) Adds a definition for ISW_ENTRY_ADDR. This is the
address to which the ROM branches when the SOC
ROM hands off execution to the boot loader.
CONFIG_SYS_TEXT_BASE and CONFIG_SPL_TEXT_BASE are set
to this value for AM43xx devices.
b) Adds CONFIG_PUB_ROM_DATA_SIZE which is used to
calculate CONFIG_SPL_MAX_SIZE. This value indicates the
amount of memory needed by the ROM to store data during
the boot process.
Currently, these CONFIG options are used only by AM43xx,
but in future other AM33xx class SOCs will also use them.
Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Daniel Allred <d-allred@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This driver supports the standard PWM API. There are 5 PWMs. Four are used
normally and the last is normally used as a timer.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Correct get_cpu_speed_grade_hz for i.MX6DQP, otherwise we
will get wrong speed grade info i.MX6DQP.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Use simpler runtime cpu dection macros.
i.MX6DL and i.MX6SOLO work the same, so use is_mx6sdl.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
i.MX6DL and i.MX6SOLO work the same, add i.MX6SOLO support
when enable/disable_ldb_di_clock_sources.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
MMCSD_MODE_FAT has been renamed to MMCSD_MODE_FS by commit 205b4f33.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The clock parent of the AHB root clock when using mux option 1
is the SYS PLL 270MHz clock. This is specified in Table 5-11
Clock Root Table of the i.MX 7Dual Applications Processor
Reference Manual.
While it could be a documentation error, the 270MHz parent is
also mentioned in the boot ROM configuration in Table 6-28: The
clock is by default at 135MHz due to a POST_PODF value of 1
(=> divider of 2).
Signed-off-by: Stefan Agner <stefan@agner.ch>
The current delays in the DDR initialization routines for am33xx
architectures are sometimes not running long enough leading to DDR
init errors. On am437x, this shows up as an L3 NOC error after the
kernel boots. This is due to the timer not being initialized
properly, but instead still containing the timer init values from
the boot ROM which cause timers to expire in 1/4th the time
required.
timer_init is typically not called until board_init_r, however on
am33xx/am43xx udelay is required in sdram_init which is called
from board_init_f, so a call to timer_init is required earlier.
Note that this issue introduced in v2015.01 by:
b352dde "am33xx: Drop timer_init call from s_init".
Although this could instead fixed by reverting said commit, it
would cause timer_init to be called twice in both SPL and non-SPL
cases. This gives a little more fine grained control and also
matches what is being done on omap-command and fsl-layerscape.
Signed-off-by: Russ Dill <russ.dill@ti.com>
Unfortunately with this change we now are unable to do FS mode boots
from MMC1 as with the way the code works today we will always load and
assume that the hard-coded raw location contains U-Boot. Further, we
cannot fix this by just changing other logic to try FS-then-RAW as it
would also make us have to ignore what order the ROM is telling us to
try.
This reverts commit 22d90d560a.
Signed-off-by: Tom Rini <trini@konsulko.com>
ABB should be initialized for all required domains voltage domain
for DRA7: IVA, GPU, EVE in addition to the existing MPU domain. If
we do not do this, kernel configuring just the frequency using the
default boot loader configured voltage can fail on many corner lot
units and has been hard to debug. This specifically is a concern with
DRA7 generation of SoCs since other than VDD_MPU, all other domains
are only permitted to setup the voltages to required OPP only at boot.
Reported-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Since we setup the voltage and frequency for the MM domain, we *must*
setup the ABB configuration needed for the domain as well. If we do not
do this, kernel configuring just the frequency using the default boot
loader configured voltage can fail on many corner lot units.
Reported-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
ABB TX_DONE mask will vary depending on ABB module. For example,
3630 never had ABB on IVA domain, while OMAP5 does use ABB on MM domain,
DRA7 has it on all domains with the exception of CORE, RTC.
Hence, move the txdone mask definition over to structure describing
voltage domain.
Signed-off-by: Nishanth Menon <nm@ti.com>
This information is already available under vcores->volts.efuse.reg.
There is no reason for duplicating the information since AVS Class 0
definitions are common for OMAP5 and DRA7 and defined with
STD_FUSE_OPP_* macros. This allows a central location of defining
the ABB and voltage definitions especially since they are reused.
This also makes it simpler to prevent mistakes involved when changing
the boot OPP for the device.
Signed-off-by: Nishanth Menon <nm@ti.com>
Add support for Technexion's PICO-IMX6UL-EMMC board.
For information about this board, please visit:
http://www.technexion.com/products/pico/pico-som/pico-imx6-emmc
Signed-off-by: Richard Hu <richard.hu@technexion.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Due to incorrect placement of the clock gate cell in the ldb_di[x]_clk tree,
the glitchy parent mux of ldb_di[x]_clk can cause a glitch to enter the
ldb_di_ipu_div divider. If the divider gets locked up, no ldb_di[x]_clk is
generated, and the LVDS display will hang when the ipu_di_clk is sourced from
ldb_di_clk.
To fix the problem, both the new and current parent of the ldb_di_clk should
be disabled before the switch. This patch ensures that correct steps are
followed when ldb_di_clk parent is switched in the beginning of boot.
This patch was ported from the 3.10.17 NXP kernel
http://git.freescale.com/git/cgit.cgi/imx/linux-2.6-imx.git/commit/?h=imx_3.10.17_1.0.1_ga&id=eecbe9a52587cf9eec30132fb9b8a6761f3a1e6d
NXP errata number: ERR009219, EB821
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
v7_maint_dcache_all() does not work reliable when build with gcc6,
see: https://bugzilla.redhat.com/show_bug.cgi?id=1318788
While debugging this I learned that v7_maint_dcache_all() is unreliable
when build with gcc5 too when it is marked as noinline.
This commit fixes the reliability issues by replacing the C-code with
the ready to use asm implementation from the kernel.
Given that this code when written as C-code clearly is quite fragile
(also see the existing comments about the C-code being the way it is
to get optimal assembly) and that we have a proven asm alternative,
I believe that this is the best solution.
Note that we actually already had a copy of the kernel's
v7_flush_dcache_all() before this commit in
arch/arm/mach-uniphier/arm32/lowlevel_init.S.
This commit moves that code arch/arm/cpu/armv7/cache_v7_asm.S, renames
it to __v7_flush_dcache_all(), and adds a v7_flush_dcache_all() wrapper
which saves / restores the clobbered registers for use from C-code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This moves the sniper board from the lge to lg, in order to match the devicetree
vendor prefix already defined in the kernel.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Some of the code in arch/arm/cpu/armv7/sunxi is actually armv7 specific, while
most of it is just generic code that could as well be used on an AArch64 SoC.
Move all files that are not really tied to armv7 into a new mach-sunxi
directory.
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The A83T has 3 USB PHYs: 1 for USB OTG, 1 for standard USB 1.1/2.0 host,
1 for USB HSIC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
As the need for various magic sram pokes has shown this maybe useful
info to have. e.g. this shows one of my a23 tablets having an id of
1661 rather then the usual 1650 for the a23.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
I noticed that for certain SoC versions boot0 does a magic poke when
build for A33. I'm not aware of this actually being necessary anywhere,
but better safe then sorry.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
We currently always modify the SVC versions of registers and only support
the short descriptor PTE format.
Some boards however (like the RPi2) run in HYP mode. There, we need to modify
the HYP version of system registers and HYP mode only supports the long
descriptor PTE format.
So this patch introduces support for both long descriptor PTEs and HYP mode
registers.
Signed-off-by: Alexander Graf <agraf@suse.de>
do_set_iodelay can now be used from board files based on needs of the
platforms variation they have.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Since many platforms may need different pad configuration required
depending on variation of the platform with minor deltas, it is
easier to maintain a sub step based approach to allow for pin mux
and iodelay configuration which may depend on the platform variations
and need to be done in IO isolation.
While we retain the older __recalibrate_iodelay function which provides
a ready sequencing, __recalibrate_iodelay_start and
__recalibrate_iodelay_end may be alternatively used now and the callers
will be responsible for the correct sequencing of operations.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Based on data from EMIF configuration tool 1.1.1. Expected update for
CTRL_WKUP_EMIF1_SDRAM_CONFIG_EXT in the next revision of the tool has
been incorporated as well.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add support for detection of SR2.0 version of DRA72x family of
processors.
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
If including MX7D in CONFIG_SYS_EXTRA_OPTIONS, CONFIG_ROM_UNIFIED_SECTIONS
will not effect.So move MX7D to Kconfig entry from CONFIG_SYS_EXTRA_OPTIONS to
"select MX7D" to boards using i.MX7 Dual.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
If including MX6SX in CONFIG_SYS_EXTRA_OPTIONS, CONFIG_ROM_UNIFIED_SECTIONS
will not effect.So move MX6SX to Kconfig entry from CONFIG_SYS_EXTRA_OPTIONS to
"select MX6SX" to boards using i.MX6 SoloX.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
This patch add support for the CCV xPress board which is equipped
with the i.MX6UL. And provides the following interfaces:
- 128MiB DDR
- UART
- I2C
- eMMC (with booting)
- Ethernet
- USB
This patch adds two build targets. One with and one without SPL. The
non-SPL version is used for loading U-Boot via USB (imx_usb_loader).
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Switch the DDR3 calibration from ad-hoc implementation of wait_for_bit()
to generic implementation of wait_for_bit().
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Configure the PMIC_STBY_REQ pin as open drain 100K according
to the design team's requirement for the PMIC_STBY_REQ pin
for i.MX 6UltraLite TO1.0.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
To i.MX6UL, default ARM rate and AHB rate is 396M and 198M,
no need to set them.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Since the MX6UL/SL/SX only has one DDR channel, in CCM_CCDR register
the bit[17] for mmdc_ch0 is reserved and its proper state should be 1.
When clear this bit, the periph_clk_sel cannot be set and that
CDHIPR[periph_clk_sel_busy] handshake never clears.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
In mctl_channel_init, (0x50<<26) which overflows 32bit.
It was supposed to be 0x50<<16,corrected now.
Reported-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
cpu_eth_init is no longer called for dm enabled eth drivers, this
was causing the sunxi gmac eth controller to no longer work in u-boot.
This commit fixes this by calling the clock, reset and pinmux setup
function from s_init() and enabling the phy power pin (if any) from
board_init().
The enabling of phy power cannot be done from s_init because it uses dm
and dm is not ready yet at this point.
Note that the mdelay is dropped as the phy gets enabled much earlier
now, so it is no longer needed.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Tested-by: Karsten Merker <merker@debian.org>
Tested-by: Michael Haas <haas@computerlinguist.org>
The H3 has USB0 - USB3, add support for having a USB vbus pin for USB3.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Fix a copy and paste error which caused us to use the uart rather then
the twi reset bits in clock_twi_onoff for sun9i.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
clock_sun8i_a83.c did not contain a clock_twi_onoff implementation
at all, this is fixed by moving the clock_sun6i.c implementation,
which is correct for the a83 too, to a shared location.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The clock_sun6i.c implementation was not deasserting the reset for
the regular i2c controllers, this commit fixes this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
I've had this one a23 tablet which would not boot and I've finally
figured out what the problem is by looking at the released boot0 code,
it seems the magic sram controller poke which we need to do in s_init()
depends on the revision of the a23.
Specifically this change is needed to get the A23 SoC I have with the
following serial to boot: "E6071AB 26Y7".
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Starting with 96e5b03 we use a linker list for partition table
information. However since we use this in SPL we need to make sure that
the SPL linker scripts include these as well. While doing this, it's
best to simply include all linker lists to future proof ourselves.
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reported-by: Nishanth Menon <nm@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
On OMAP4 platforms that also need to calculate their DDR settings we are
now getting very close to the linker limit size. Since OMAP44XX is only
seen with LPDDR2, remove some run time tests for LPDDR2 or DDR3 as we
will know that we don't have it for OMAP44XX.
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Since the SAR registers are filled with garbage on cold reset, this checks for a
warm reset to assert the validity of reboot mode.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reboot mode is written to SAR memory before reboot in the form of a string.
This mechanism is supported on OMAP4 by various TI kernels.
It is up to each board to make use of this mechanism or not.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
This correctly enables the USB PHY clocks, by enabling CM_ALWON_USBPHY_CLKCTRL
and correctly setting CM_L3INIT_USBPHY_CLKCTRL's value.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
On (at least) OMAP4, the USB DPLL is required to be setup for the internal PHY
to work properly. The internal PHY is used by default with the MUSB USB OTG
controller.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
The Amazon Kindle Fire (first generation) codename kc1 is a tablet that was
released by Amazon back in 2011.
It is using an OMAP4430 SoC GP version, which allows running U-Boot and the
U-Boot SPL from the ground up.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
I2C is often enabled withing the U-Boot SPL, thus those clocks are required to
be enabled early (especially when the bootrom doesn't enable them for us).
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
This removes a duplicate reference to CM_L3INIT_USBPHY_CLKCTRLin
enable_basic_uboot_clocks. Also, a doubled whitespace is removed.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
save_omap_boot_params is called from spl_board_init in the SPL context. Thus,
there is no reason to duplicate that call on arch_cpu_init.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
There is no distinction between essential and non-essential mux configuration,
so it doesn't make sense to have an "essential" prefix.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Individual boards might provide their own emif_get_device_timings function and
use the jedec timings in their own way, hence those have to be exported.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Individual boards might provide their own emif_get_device_timings function and
use the elpidia timings in their own way, hence those have to be exported.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Individual boards might provide their own emif_get_device_details function and
use elpidia device details in their own way, hence those have to be exported.
This also wraps existing definitions with the proper ifdef logic.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
This introduces a define for the offset to the reboot reason, rather than
hardcoding it.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
This switches reboot mode handling to a string-based interface, that allows more
flexibility to set a common interface with the next generations of OMAP devices.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
The newer versions of DRA7 boards has EEPROM populated with DDR
size specified in it. Moving DRA7 specific emif related settings
to board files so that emif settings can be identified based on EEPROM.
Acked-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
A few boards still use ns16550_platdata structures, but assume the structure
is going to be in a specific order. By explicitly naming each entry,
this should also help 'future-proof' in the event the structure changes.
Tested on the Logic PD Torpedo + Wireless.
I only changed a handful of devices that used the same syntax as the Logic
board. Appologies if I missed one or stepped on toes. Thanks to Derald Woods
and Alexander Graf.
Signed-off-by: Adam Ford <aford173@gmail.com>
V6: Add fix to arch/arm/cpu/armv7/am33xx/board.c
V5: Add fix to arch/arm/cpu/arm926ejs/lpc32xx/devices.c
V4: Fix subject heading
V3: Remove reg_offset out in all the structs. It was reverted out, and and if
it did exist, it would get initialized to 0 by default.
V2: I hastily copy-pasted the boards without looking at the UART number.
This addresses 3 boards that use UART3 and not UART1.
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Early system initialization is being done before initf_dm is being called
in U-Boot. Then system will fail to boot if any of the DM enabled driver
is being called in this system initialization code. So, rearrange the
code a bit so that DM enabled drivers can be called during early system
initialization.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Given that DRA7/OMAP5 SoCs can support more than 2GB of memory,
enable interleaving for this higher memory to increase performance.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Read and write leveling can be enabled independently. Check for these
enable bits before updating the read and write leveling output values.
This will allow to use the combination of software and hardware leveling.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Commit (20fae0a - ARM: DRA7: DDR: Enable SR in Power Management Control)
enables Self refresh mode by default and during warm reset the EMIF
contents are preserved. After warm reset EMIF sees that it is idle and
puts DDR in self-refresh. When in SR, leveling operations cannot be done
as DDR can only accept SR exit command, so its hanging during warm reset.
In order to fix this reset the power management control register before
EMIF initialization if it is a warm reset.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
On DRA7, refresh ctrl shadow should be updated with
the final value.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Current AM57xx evm supports both BeagleBoard-X15
(http://beagleboard.org/x15) and AM57xx EVM
(http://www.ti.com/tool/tmdxevm5728).
The AM572x EValuation Module(EVM) provides an affordable platform to
quickly start evaluation of Sitara. ARM Cortex-A15 AM57x Processors
(AM5728, AM5726, AM5718, AM5716) and accelerate development for HMI,
machine vision, networking, medical imaging and many other industrial
applications. This EVM is based on the same BeagleBoard-X15 Chassis
and adds mPCIe, mSATA, LCD, touchscreen, Camera, push button and TI's
wlink8 offering.
Since the EEPROM contents are compatible between the BeagleBoard-X15 and
the AM57xx-evm, we add support for the detection logic to enable
support for various user programmable scripting capability.
NOTE: U-boot configuration is currently a superset of AM57xx evm and
BeagleBoard-X15 and no additional configuration tweaking is needed.
This change also sets up the stage for future support of TI AM57xx EVMs
to the same base bootloader build.
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Many TI EVMs have capability to store relevant board information
such as DDR description in EEPROM. Further many pad configuration
variations can occur as part of revision changes in the platform.
In-order to support these at runtime, we for a board detection hook
which is available for override from board files that may desire to do
so.
NOTE: All TI EVMs are capable of detecting board information based on
early clocks that are configured. However, in case of additional needs
this can be achieved within the override logic from within the board
file.
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Early clock initialization is currently done in two stages for OMAP4/5
SoCs. The first stage is the initialization of console clocks and
then we initialize basic clocks for functionality necessary for SoC
initialization and basic board functionality.
By splitting up prcm_init and centralizing this clock initialization,
we setup the code for follow on patches that can do board specific
initialization such as board detection which will depend on these
basic clocks.
As part of this change, since the early clock initialization
is centralized, we no longer need to expose the console clock
initialization.
NOTE: we change the sequence slightly by initializing console clocks
timer after the io settings are complete, but this is not expected
to have any functioanlity impact since we setup the basic IO drive
strength initialization as part of do_io_settings.
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
If HDMI_IH_FC_STAT2_OVERFLOW_MASK is set, we need to
do TMDS software reset and write to clear fc_invidconf register.
We need minimum 3 times to write to clear the fc_invidconf
register, so choose 5 loops here.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Signed-off-by: Sandor Yu <sandor.yu@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Read the number of cores in the fuses to distinguish between
the dual and solo versions.
Tested on a mx7d sabresd and on a mx7solo warp7.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Add support for GE B450v3, B650v3 and B850v3 boards. The boards
are based on Advantech BA16 module which has a i.MX6D processor.
The boards support:
- FEC Ethernet
- USB Ports
- SDHC and MMC boot
- SPI NOR
- LVDS and HDMI display
Basic information about the module:
- Module manufacturer: Advantech
- CPU: Freescale ARM Cortex-A9 i.MX6D
- SPECS:
Up to 2GB Onboard DDR3 Memory;
Up to 16GB Onboard eMMC NAND Flash
Supports OpenGL ES 2.0 and OpenVG 1.1
HDMI, 24-bit LVDS
1x UART, 2x I2C, 8x GPIO,
4x Host USB 2.0 port, 1x USB OTG port,
1x micro SD (SDHC),1x SDIO, 1x SATA II,
1x 10/100/1000 Mbps Ethernet, 1x PCIe X1 Gen2
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Now that we fall back to the FS code path when we don't find u-boot
at the raw sector offset, there is no good reason to not default to
raw boot.
With this patch, I can successfully boot u-boot from a raw sector
offset on beagle-xm.
Signed-off-by: Alexander Graf <agraf@suse.de>
This introduces some minor cleanups, regarding aspects such as board name, code
and headers organization as well as deprecated and missing config options.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
The initialization for smmu and stream id is moved into the common soc
code.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add support for phy 1-3.
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
[hdegoede@redhat.com: use setclrbits_le32 instead of read-modify-write]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
In current design, if any peripheral was assigned to both A7 and M4,
it will receive ipg_stop or ipg_wait when any of the 2 platforms
enter low power mode. We will have a risk that, if A7 enter wait,
M4 enter stop, peripheral will have chance to get ipg_stop and ipg_wait
asserted same time. Also if M4 enters stop mode, A7 will have no
chance to access the peripheral.
There are 26 peripherals affected by this IC issue:
SIM2(sim2/emvsim2)
SIM1(sim1/emvsim1)
UART1/UART2/UART3/UART4/UART5/UART6/UART7
SAI1/SAI2/SAI3
WDOG1/WDOG2/WDOG3/WDOG4
GPT1/GPT2/GPT3/GPT4
PWM1/PWM2/PWM3/PWM4
ENET1/ENET2
Software Workaround:
The solution is to set the peripherals to Domain0 by A core, since A core
in Domain0. The peripherals which will be used by M4, will be set to Domain1
by M4.
For example, A core set WDOG4 to domain0, but when M4 boots up, M4 will
set WDOG4 to domain1, because M4 will use WDOG4.
So the peripherals are not shared by them. This way requires
the uboot implemented the RDC driver and set the 26 IPs above
to domain 0 only. M4 image will set the M4 to domain 1 and
set peripheral which it will use to domain 1.
This patch enables the CONFIG_IMX_RDC and CONFIG_IMX_BOOTAUX for
i.MX7D SABRESD board, and setup the 26 IP resources to domain 0.
Signed-off-by: Ye.Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Implement arch_auxiliary_core_up and arch_auxiliary_core_check_up.
arch_auxiliary_core_check_up is used to check whether M4 is running
or not. arch_auxiliary_core_up is to boot M4 core, the m4 core will
use the pc and stack which is set in arch_auxiliary_core_up to set R15
and R13 register and boot.
Signed-off-by: Ye.Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Implement arch_auxiliary_core_up and arch_auxiliary_core_check_up.
arch_auxiliary_core_check_up is used to check whether M4 is running
or not. arch_auxiliary_core_up is to boot M4 core, the m4 core will
use the pc and stack which is set in arch_auxiliary_core_up to set R15
and R13 register and boot.
Signed-off-by: Ye.Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
commit 216d286c7e [imx: mx6: implement
mmc_get_env_dev] introduced selection of the environment device according
to the boot device when booting from SD/MMC.
Extend this functionality for also selecting the device partition.
Signed-off-by: Soeren Moch <smoch@web.de>
The defconfig patch will enable the the SPL and NAND settings.
The update to Kconfig will allow the SPL to configured in and
built.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Correct spelling of "U-Boot" shall be used in all written text
(documentation, comments in source files etc.).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
Implement mmc_get_env_dev, devno can be got from smbr1 of SRC.
Introduce a weak function board_mmc_get_env_dev, different
boards can implement it according to different sdhc controllers
that used by the board.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Move mmc_get_env_devno to soc.c and rename to mmc_get_env_dev to
match the one in common/env_mmc.c.
Introduce a weak function board_mmc_get_env_dev. Different
boards can implement this according to sdhc controller which
is used by the board.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
The checking with max frequency supported is not correct, because the temp
is calculated by max pre and post dividers. We can decrease any divider to
meet the max frequency limitation. Actually, the calculation below the codes
is doing this way to find best pre and post dividers.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Wrong checking for the base_addr paramter with LCDIF1 and LCDIF2. Always
enter the -EINVAL return.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Initial version for mx6sx SABREAUTO board support with features:
PMIC, QSPI, NAND flash, SD/MMC, USB, Ethernet, I2C, IO Expander.
Signed-off-by: Ye Li <ye.li@nxp.com>
Add DDR3 calibration code for i.MX6Q, i.MX6D and i.MX6DL. This code
fine-tunes the behavior of the MMDC controller in order to improve
the signal integrity and memory stability.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Add code to aid tracking down cache alignment issues.
In case DEBUG is defined in the cache.c, this code will
check alignment of each attempt to flush/invalidate data
cache and print a warning if the alignment is incorrect.
If DEBUG is not defined, this code is optimized out.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@konsulko.com>
eth_get_dev_by_index() is an API which is not available in driver
model. Use eth_get_dev_by_name() instead, which can also simplifly
the code logic a little bit.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Banana-pi M3 has LPDDR3 DRAM. this adds support for LPDDR3 for A83T.
Mostly the timing parameters are different from DDR3.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Different A83T boards have different DRAM types. Banapi M3 has LPDDR3,
Allwinner Homlet v1.2 has DDR3.
This adds groundwork to support for new DRAM type for A83T.
Introduce CONFIG_DRAM_TYPE, It'll be 3 for DDR3 and 7 for LPDDR3, must
be set in respective board defconfig.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This removes the redundant lines of code from mctl_sys_init.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
H3 has the same power sequencing procedure as the A31/A31s, which
includes the power clamps.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
H3's CCU includes some switches which disable non-secure access to some
of the more critical clock controls, such as MBUS, PLLs, and main
platform busses.
Configure them to enable non-secure access.
For now the only SoC that has this feature is the H3. For other
platforms just use a default (weak) empty function so things do
not break.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Secure Memory Touch Arbiter is the same thing as the TrustZone
Protection Controller found on A31/A31s.
Access to many peripherals on the H3 can be controlled by the SMTA,
and the settings default to secure access only.
This patch supports the new settings, and sets them to allow non-secure
access.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Updated the default sata register values to enhance the
performance and stability.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The management data input/output (MDIO) requires open-drain,
i.MX7D TO1.0 ENET MDIO pin has no open drain, but TO1.1 supports
this feature. So to TO1.1, need to enable open drain by setting
bits GPR0[8:7] for TO1.1.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Check "Figure 19-5. BUS clock generation" of i.MX 6SoloX Applications
Processor Reference Manual and "Figure 18-5. BUS clock generation" of
i.MX 6UltraLite Applications Processor Reference Manual. If mmdc clk
sources from pll4_main_clk(pll_audio), the calculation is wrong.
Fix mmdc_ch0 clk calculation. Also add PLL_AUDIO/VIDEO support
for decode_pll.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
[hdegoede@redhat.com: Minor cleanups]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
applied with fixing 2 checkpatch warnings:
WARNING: please, no space before tabs
Signed-off-by: Heiko Schocher <hs@denx.de>
To prepare timer driver to DM/DT conversion do not build the
exiting timer driver when CONFIG_TIMER is defined. But since
omap's SPL doesn't support DM yet so built timer driver only for
SPL build when CONFIG_TIMER is defined.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
On these platforms we have many cases of boards that enable device model
and GPIO support but do not enable OF_CONTROL and pass in a device tree
with the binary. We need to bring in the platform data here as well.
Tested on Beaglebone Black.
Reported-by: Robert Nelson <robertcnelson@gmail.com>
Reported-by: Francisco Aguerre <franciscoaguerre@gmail.com>
Reported-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
This is a workaround for hardware erratum.
Write the value of 63b2_0042h to EDDRTQCFG will optimal the
memory controller performance.
The value: 63b2_0042h comes from the hardware team.
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Enable snoop and DVM message on all CCI-400 slave ports. Setting
on disabled feature (snoop or DVM) is ignored by CCI-400.
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
[York Sun: Add commit message]
Reviewed-by: York Sun <yorksun@freescale.com>
Since the changes in a1e56cf the way that we had board_mmc_init()
structured for OMAP parts (so that we always report device 0) are no
longer functional. For now, make the case of booting from the second
device initialize both devices (we have no devices that only have the
second device as MMC). A further rework and consolidation of the
functions should be done at a later date.
Tested on Beaglebone Black (SD and eMMC boot).
Reported-by: Vagrant Cascadian <vagrant@debian.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Enable the IP feature's snoop signal to support
hardware snoop for cache coherence.
SNPCNFGCR contains the bits to drive snoop signal
for various masters.
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Create a soc.c file to put the code for soc special settings.
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch fixes the DDR3 initialization procedure in
order to comply with DDR3 standard. A 500 us delay is specified
between the DDR3 reset and clock enable signal. Until now,
this delay was not respected. Some DDR3 chips don't bother
but the bigger the RAM becomes the more likely it seems that
this delay is needed. We observed that DRAM > 256 MB from
the manufacturer Samsung have an issue when the specification
is not respected.
Changes:
1) Add a 1 ms wait for L3 timeout error trigger
2) Don't delay DDR3 initialization
Bit 31 of emif_sdram_ref_ctrl shouldn't be set because his
suppresses the initialization of DDR3
Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Reviewed-by: James Doublesin <doublesin@ti.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Roger Meier <r.meier@siemens.com>
Cc: Heiko Schocher <hs@denx.de>
The read delays were set incorrectly, leading to reliability
issues at higher DRAM clock speeds. This commit adjusts this
to match the vendor boot0 behaviour.
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Tested-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add some spaces around operators.
Signed-off-by: Olliver Schinagl <o.schinagl@ultimaker.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Commit 6c739c5d added code to enable i2c bus 4 and 5 on the sun7i SoC
but forgot to extend the range check in clock_twi_onoff, resulting in
the clock not getting enabled.
The range-check is not needed at all, since clock_twi_onoff only gets
called with such high indexes when CONFIG_I2C3_ENABLE / CONFIG_I2C4_ENABLE
is set and Kconfig already only allows these on sun6i / sun7i.
This commit removes the range-check all together fixing i2c bus 4 and 5
not working on sun7i.
Signed-off-by: Olliver Schinagl <o.schinagl@ultimaker.com>
[hdegoede@redhat.com] Remove range check instead of extending it
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add support for A83T dram. Register are different from sun8i A33.
init code is similar to A33 dram init.
hope we'll shift duplicate code in dram_sun8i_*
to dram helper in future.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add basic clocks pll1, pll5, and some default values from allwinner u-boot.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
[hdegoede@redhat.com] Fix PLL6 init to run at 600 MHz instead of 288 MHz,
fixing the mmc support not working
[hdegoede@redhat.com] Fix PLL init code to properly wait for the PLL-s to
stabilize, fixing cold-booting directly from sdcard not working
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Enabled support for AXP818 in SPL and u-boot.
DCDC1, DCDC2, DCDC3 and DCSC5 are enabled.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
On A83T, PB9,PB10 are UART0 pins.
On allwinner A83T Dev board(h8homlet), this uart0 serial connector
is exposed.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Allwinner A83T is octa-core cortex-a7 SOC.
This enables support for A83T.
SMP is not yet supported.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
We now want to make sure that we have the platform data for NS16550 when
we do not have OF_CONTROL set.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch addresses a problem mentioned recently on this mailing list:
[1].
In that posting a LS1021 based system was locking up at about 5 minutes
after boot,but the problem was mysteriously related to the toolchain
used for building u-boot.Debugging the problem reveals a stuck
interrupt 29 on the GIC.
It appears Freescale's LS1021 support in u-boot erroneously sets the
64-bit ARM generic PL1 physical time CompareValue register to all-ones
with a 32-bit value.This causes the timer compare to fire 344 seconds
after u-boot configures it.Depending on how fast u-boot gets the
kernel booted,this amounts to about 5-minutes of Linux uptime before
locking up.
Apparently the bug is masked by some toolchains. Perhaps this is
explained by default compiler options, word sizes, or binutils versions.
To fix the above issue, the generic physical timer is disabled
before jumping to the OS.
[1]
https://lists.yoctoproject.org/pipermail/meta-freescale/2015-June/014400.html
Signed-off-by: Chris Kilgour <techie@whiterocker.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch addresses a problem mentioned recently on this mailing list:
[1].
In that posting a LS1021 based system was locking up at about 5 minutes
after boot, but the problem was mysteriously related to the toolchain
used for building u-boot. Debugging the problem reveals a stuck
interrupt 29 on the GIC.
It appears Freescale's LS1021 support in u-boot erroneously sets the
64-bit ARM generic PL1 physical time CompareValue register to all-ones
with a 32-bit value. This causes the timer compare to fire 344 seconds
after u-boot configures it. Depending on how fast u-boot gets the
kernel booted, this amounts to about 5-minutes of Linux uptime before
locking up.
Apparently the bug is masked by some toolchains. Perhaps this is
explained by default compiler options, word sizes, or binutils versions.
At any rate this patch makes the manipulation explicitly 64-bit which
alleviates the issue.
[1]
https://lists.yoctoproject.org/pipermail/meta-freescale/2015-June/014400.html
Signed-off-by: Chris Kilgour <techie@whiterocker.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
On mx6sx, the CCM register bits for GPMI are different as other
mx6 platforms. Modify the GPMI clock function to support mx6sx.
Signed-off-by: Ye.Li <B37916@freescale.com>
Congatec has several MX6 boards based on quad, dual, dual-lite and solo.
Add SPL support so that all the variants can be supported
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
serial_init() reads global_data, since global_data is not yet
initialized, this can cause unwanted behaviour leading to QSPI XIP boot
hang. Also, since serial_init() is anyways called later from
boar_init_f(), it does not make sense to do the same in s_init().
Tested on AM437x IDK EVM with QSPI XIP boot.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The 3.4 kernel from the Allwinner SDK is clocking AHB1 at 200MHz
on Allwinner H3 and using PLL6 as the clock source (PLL6/3).
This can be verified by reading the value of the AHB1_APB1_CFG_REG
register via /dev/mem. It always reads as 0x3180 regardless of
the current cpufreq operating point. So this configuration should
be safe for use in U-Boot too.
PLL6 also needs to be configured before it is used as the clock
source, according to the "CCU / Programming Guidelines" section
of the Allwinner manual.
The current low AHB1 clock speed is limiting the USB transfer
speed when booting via FEL. This patch can increase the FEL USB
transfer speed from ~510 KB/s to ~950 KB/s.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Based on existing A23/A33 code and the original H3 boot0.
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add initial sun8i H3 support, only uart + mmc are supported for now.
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Currently the mmc device that SPL looks at is always mmc0, regardless
of the BOOT_DEVICE_MMCx value. This forces some boards to
implement hacks in order to boot from other mmc devices.
Make SPL take into account the correct mmc device.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
Make spl_*_load_image() functions return a value instead of
hanging if a problem is encountered. This enables main spl code
to make the decision whether to hang or not, thus preparing
it to support alternative boot devices.
Some boot devices (namely nand and spi) do not hang on error.
Instead, they return normally and SPL proceeds to boot the
contents of the load address. This is considered a bug and
is rectified by hanging on error for these devices as well.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Hans De Goede <hdegoede@redhat.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Jagan Teki <jteki@openedev.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
BeagleBoard X15 (http://beagleboard.org/x15) support in u-boot does
actually support two different platform configuration offered by
TI. In addition to BeagleBoard X15, it also supports the TMDXEVM5728
(or more commonly known as AM5728-evm).
Information about the TI AM57xx EVM can be found here
http://www.ti.com/tool/tmdxevm5728
The EVM configuration is 1-1 compatible with BeagleBoard X15 with the
additional support for mPCIe, mSATA, LCD, touchscreen, Camera, push
button and TI's wlink8 offering.
Hence, we rename the beagle_x15 directory to am57xx to support TI
EVMs that use the AM57xx processor. By doing this we have common code
reuse. This sets the stage to have a common u-boot image solution for
multiple TI EVMs such as that already done for am335x and am437x. This
sets the stage for upcoming multiple TI EVMs that share the same code
base.
NOTE: Commit eae7ae1853 ("am437x: Add am57xx_evm_defconfig using
CONFIG_DM") introduced DT support for beagle_x15 under am57xx_evm
platform name. However, this ignored the potential confusion arising for
users as a result. To prevent this, existing beagle_x15_defconfig is
renamed as am57xx_evm_nodt_defconfig to denote that this is the "non
device tree" configuration for the same platform. We still retain
am57xx-beagle-x15.dts at this point, since we just require the common
minimum dts.
As a result of this change, users should expect changes in build
procedures('make am57xx_evm_nodt_defconfig' instead of 'make
beagle_x15_defconfig'). Hopefully, this would be a one-time change.
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Schuyler Patton <spatton@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
We need to power down lcdif before uboot reset to make reset can pass
stress test.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Implement mxs_set_lcdclk, enable_lcdif_clock and enable_pll_video.
The three API can be used to configure lcdif related clock when
CONFIG_VIDEO_MXS enabled.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
1. add basic psci support for imx7 chip.
2. support cpu_on and cpu_off.
3. switch to non-secure mode when boot linux kernel.
4. set csu allow accessing all peripherial register in non-secure mode.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
The CPU name for Exynos was concatenated with cpu id,
but for new Exynos platforms, like Chromebook Peach Pi
based on Exynos5800, the name of SoC variant does not
include the real SoC cpu id (0x5422).
For such case, the CPU name should be defined in device tree.
This commit introduces new device-tree property for Exynos:
- "cpu-model" - with cpu name string
If defined, then the cpu id is not printed.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Rework unified section macro select via Kconfig option
instead of macro definition in mx7_common header file.
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Add CONFIG_ROM_UNIFIED_SECTIONS for mx6sx and mx6ul target
platforms to resolve corresponding HAB_RVT_BASE base address,
the RVT table contains pointers to the HAB API functions in
ROM code.
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Rework secure boot support for imx6, move existing hab support
for imx6 into imx-common for SoC reuse.
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Freescale ARM-based Layerscape LS102xA contain a SATA controller
which comply with the serial ATA 3.0 specification and the
AHCI 1.3 specification.
This patch adds SATA feature on ls1021aqds and ls1021atwr boards.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Enable snooping for CAAM read & write transactions by
programming the SCFG snoop configuration register:
SCFG_SNPCNFGCR[SECRDSNP]
SCFG_SNPCNFGCR[SECWRSNP]
Signed-off-by: Horia Geantă <horia.geanta@freescale.com>
Reviewed-by: Zhengxiong Jin <Jason.Jin@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
As QSPI/DSPI and IFC are pin multiplexed, IFC is disabled
in SD boot for QSPI. This patch will add fdt support for
this rule.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Since there is a common function to grab the serial number from the die id bits,
it makes sense have one to parse that serial number and feed it to the serial
ATAG.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
This introduces omap_die_id_display to display the full die id.
There is no need to store it in an environment variable, that no boot script
is using anyway.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
Now that we have a common prototype to grab the omap die id, functions to figure
out a serial number and usb ethernet address can use it directly.
Those also get an omap_die_id prefix for better consistency.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
This introduces omap5 support for omap_die_id, which matches the common
omap_die_id definition. It replaces board-specific code to grab the die id bits.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
This introduces omap4 support for omap_die_id, which matches the common
omap_die_id definition. It replaces board-specific code to grab the die id bits.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
This replaces the previous get_dieid definition with omap_die_id, that matches
the common omap_die_id definition.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
This introduces a common definition for omap_die_id, that aims at providing a
common interface for accessing omap platform's die id bits.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
So far, even if CONFIG_MMC was not enabled the board code was trying to use
the MMC-related functions, resulting in linker errors.
Protect those calls by an ifdef.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Stop prefixing the axp functions for setting voltages, etc. with the
model number, there ever is only one pmic driver built into u-boot,
this allows simplifying the callers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
common/dlmalloc.c is quite big, both in .text and .data usage. E.g. for a
Mele_M9 sun6i board build this reduces .text from 0x4214 to 0x3b94 bytes,
and .data from 0x54c to 0x144 bytes.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Tom Rini <trini@konsulko.com>
Since commit 623d96e89aca6("imx: wdog: correct wcr register settings")
issuing a 'reset' command causes the system to hang.
Unlike i.MX and Vybrid, the watchdog controller on LS102x is big-endian.
This means that the watchdog on LS1021 has been working by accident as
it does not use the big-endian accessors in drivers/watchdog/imx_watchdog.c.
Commit 623d96e89aca6("imx: wdog: correct wcr register settings") only
revelead the endianness problem on LS102x.
In order to fix the reset hang, introduce a reset_cpu() implementation that
is specific for ls102x, which accesses the watchdog WCR register in big-endian
format. All that is required to reset LS102x is to clear the SRS bit.
This approach is a temporary workaround to avoid a regression for LS102x
in the 2015.10 release. The proper fix is to make the watchdog driver
endian-aware, so that it can work for i.MX, Vybrid and LS102x.
Reported-by: Sinan Akman <sinan@writeme.com>
Tested-by: Sinan Akman <sinan@writeme.com>
Reviewed-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
We run 4 Arndale boards in our automated test framework, they have
been running quite happily for quite some time using a Debian Wheezy
userspace.
However when upgrading to a Debian Jessie we started seeing frequent
segmentation faults from gcc when building the kernel, to the extent
that it is unable to successfully build the kernel twice in a row, and
often fails on the first attempt.
Searching around I found https://bugs.launchpad.net/arndale/+bug/1081417
which pointed towards http://www.spinics.net/lists/kvm-arm/msg03723.html
and CPU Errata 773022 and 774769.
This errata needs to be applied to all processors in an SMP system,
meaning that the usual strategy of applying them in
arch/arm/cpu/armv7/start.S is not appropriate (since that applies to
the boot processor only). Instead we apply these errata in the secure
monitor which is code that is traversed by all processors as they are
brought up.
The net affect on Arndale is that ACTLR changes from 0x40 to
0x2000042. I ran 17 kernel compile iterations overnight with no
segfaults.
Runtime testing was done on our v2014.10 based branch and forward
ported (with only minimal and trivial contextual conflicts) to current
master, where it has been build tested only.
I suppose in theory these errata apply to any Exynos5250 based boards,
but Arndale is the only one I have access to and I have therefore
chosen to be conservative and only apply it there.
Also, reorder CONFIG_ARM_ERRATA_794072 in README to make the list
numerically sorted.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
We should follow 'read->set/clr bit->write' flow for enable_fec_anatop_clock,
otherwise we may overridden configuration before enable_fec_anatop_clock.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Cc: Fabio Estevam <fabio.estevam@freescale.com>
This patch extends the misc_init_r() function on sunxi boards
to test for the presence of a suitable "sunxi" SPL header. If
found, and the loader ("fel" utility) provided a non-zero value
for the boot.scr address, then the corresponding environment
variable fel_scriptaddr gets set.
misc_init_r() also sets (or clears) the "fel_booted" variable depending
on the active boot device, using the same logic as spl_boot_device().
The goal is to provide sufficient information (within the U-Boot
environment) to make intelligent decisions on how to continue the boot
process, allowing specific customizations for the "FEL boot" case.
Signed-off-by: Bernhard Nortmann <bernhard.nortmann@web.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
crt0.S will both memset the bss sectioan and call board_init_r for us,
so there is no need to do either ourselves.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
drop select CPU_V7 for board target, since ARCH_MX7 selects CPU_V7.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
This arch does not seem to be supported / used at all in the current
U-Boot mainline source tree any more. So lets remove the core u8500 code
and code that was only referenced by this platform.
Please note that this patch also removes these config options:
- CONFIG_PL011_SERIAL_RLCR
- CONFIG_PL011_SERIAL_FLUSH_ON_INIT
As they only seem to be referenced by u8500 based boards. Without any
such board in the current code, these config option don't make sense
any more. Lets remove them as well.
If someone still wants to use this platform, then please send patches
to re-enable support by adding at least one board that references this
code.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: John Rigby <john.rigby@linaro.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Discard the 'select CPU_V7' from Kconfig in arch/arm/cpu/armv7/mx6
for different targets, because ARCH_MX6 selects CPU_V7.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
This patch is to support mx6ul_9x9_evk board based on mx6ul_14x14_evk,
the difference between mx6ul 9x9 evk and mx6ul 14x14 evk are:
1. mx6ul 9x9 evk use pfuze3000, while mx6ul 14x14 evk use DCDC.
2. mx6ul 9x9 evk supports 256MB LPDDR2, while mx6ul 14x14 evk
supports 512MB DDR3
3. mx6ul_9x9_evk use 9x9 package, while mx6ul_14x14_evk use 14x14 package.
This patch add the following:
1. Discard PHYS_SDRAM_SIZE from header file, use imx_ddr_size()
2. Introduce a macro is_mx6ul_9x9_evk using
CONFIG_IS_ENABLED(TARGET_MX6UL_9X9_EVK) to avoid "#ifdef xxx" in non-SPL
part. To SPL part, CONFIG_IS_ENABLED(TARGET_MX6UL_9X9_EVK) can not work,
so still use "#ifdef CONFIG_TARGET_MX6UL_9X9_EVK" to differentiate with
mx6ul_14x14_evk. And we have no way to dymaically checking this chip
is 9x9 or 14x14.
3. mx6ul_9x9_evk use pfuze3000, so enabled POWER related configurations.
POWER related configurations also effect for mx6ul_14x14_evk. But
power_init_board implementation using 'if (is_mx6ul_9x9_evk())' to
do initialization for mx6ul_9x9_evk, and do nothing for mx6ul_14x14_evk.
4. mx6ul_9x9_evk use lpddr2 with size 256MB, so add related SPL DRAM
configurations.
5. Enable CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG and setting dtb file
according to board_rev and board_name.
6. Add TARGET_MX6UL_9X9_EVK Kconfig entry
Boot Log:
U-Boot SPL 2015.10-rc2-00356-g536ce34 (Sep 06 2015 - 12:22:53)
reading u-boot.img
reading u-boot.img
U-Boot 2015.10-rc2-00356-g536ce34 (Sep 06 2015 - 12:22:53 +0800)
CPU: Freescale i.MX6UL rev1.0 792 MHz (running at 396 MHz)
CPU: Commercial temperature grade (0C to 95C) at 41C
Reset cause: POR
Board: MX6UL 9x9 EVK
I2C: ready
DRAM: 256 MiB
PMIC: PFUZE3000 DEV_ID=0x30 REV_ID=0x11
MMC: FSL_SDHC: 0, FSL_SDHC: 1
In: serial
Out: serial
Err: serial
Net: FEC1
Hit any key to stop autoboot: 0
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
This reverts commit 059323fb6a8f21637bb617919715c2427f24777c.
This commit 059323fb6a8f21637bb617919715c2427f24777c use JESD79-3E which
is not the newest spec. Should use JESD79-3F in which tRFC is 260ns for
4Gb chip.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Add imx-common cpu support for imx7d SoC
- Update reset_cause for imx7d
- Enable watchdog driver built for imx7d
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Add imx7d basic SoC system support
Misc arch dependent functions for system bring up
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
* Add Clock control module (CCM) support
* iMX7D SoC introduces 3 main clock sysmtem abstraction for clock
root frequency generation denominated clock slices.
Core clock slice: hihg speed clock for ARM core
Bus clock slice: for bus clocks
IP clock slice: Peripheral clocks
* At system boot ROM enables PLL_ARM, PLL_DDR, PLL_SYS, PLL_ENET
In u-boot, we have to:
- Configure PFD3- PFD7 for freq we needed in u-boot
- Set clock root for peripherals (ip channel)
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
Move common imx6 arch init setup, init.c can be extended
and reused to support imx7 SoC keeping init arch common
code.
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Rework cache settings for imx6, move cache configuration
to imx-common/cache.c so it can be reused for newer SoC
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Rework imx_thermal driver to be used across i.MX
processor that support thermal sensor
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
clrsetbits_le32/clrbits_le32 takes mask of the bits as input that
are needed to be set/clear. But emif driver passes the shift of the bits.
Fixing it here.
Reported-by: Mark Mckeown <m-mckeown@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Booting the kernel fails on RK3288 (and probably other rockchip SoCs)
when the i-cache is disabled/flushed before d-cache.
I have not investigated whether this is due to U-Boot hanging or whether
it's very early in the linux boot, but following the approach of the
various rockchip U-Boot forks (first disable d-cache then i-cache) makes
things work.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Since we need to support runtime check for different drivers, we need
to add get_cpu_rev for vf610, otherwise there will be build errors.
This patch introduces a dummy CPU id which is not read from chip
silicon. Later when we can get the real id from chip, can fix the
value of MXC_CPU_VF610 then.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Suggested-by: Stefano Babic <sbabic@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
there is a 2b board version of the aristainetos2
board. Differences to the v2:
- spi cs for the nor flash and display controller
changed
- some pinmux changes
- LED gpio settings changed
Signed-off-by: Heiko Schocher <hs@denx.de>
There is no need to expose SoC choice to user, we already got
the SoC according to the build target. So default "select MX6UL"
for MX6UL_14x14_EVK target.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Add SPL boot support for mx6slevk board.
1. Introduce a configuration file mx6slevk_spl_defconfig.
2. i.MX6SL has same DRAM space with i.MX6SX, need to change SPL DRAM SPACE.
3. Include imx6_spl.h and related SPL macro in mx6slevk.h.
4. select SUPPORT_SPL for TARGET_MX6SLEVK.
5. Add SPL board code to do related initialization.
Boot Log:
U-Boot SPL 2015.07-00544-g1594a76 (Aug 17 2015 - 01:56:59)
reading u-boot.img
reading u-boot.img
U-Boot 2015.07-00544-g1594a76 (Aug 17 2015 - 01:56:59 +0000)
CPU: Freescale i.MX6SL rev1.2 996 MHz (running at 396 MHz)
CPU: Commercial temperature grade (0C to 95C) at 50C
Reset cause: POR
Board: MX6SLEVK
I2C: ready
DRAM: 1 GiB
PMIC: PFUZE100 ID=0x10
MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: FEC [PRIME]
Hit any key to stop autoboot: 0
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Add LPDDR2 support:
1. Implement a function mx6_lpddr2_cfg to initialize MMDC for LPDDR2.
2. Introduce a structure mx6_lpddr2_cfg, most entrys are same to
mx6_ddr3_cfg, but still keep it a single one for easy to choose
parameters for LPDDR2.
3. If ddr_type is LPDDR2, use mx6_lpddr2_cfg to init MMDC.
4. Update comments.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
To i.MX6, DDR3 and LPDDR2 is supported, so rename function mx6_dram_cfg
to mx6_ddr3_cfg and the original mx6_dram_cfg function only is a wrapper.
The new reimplemented function mx6_dram_cfg only invokes mx6_ddr3_cfg
when ddr_type is for DDR3. Later we can use ddr_type to initialize
MMDC for LPDDR2.
Initialize ddr_type for different boards which enable SPL.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Define two structure mx6sl_iomux_ddr_regs and mx6sl_iomux_grp_regs.
Add a new function mx6sl_dram_iocfg to configure dram io.
Add header file to define macros for register address.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
To Chip density 4Gb, tRFC should be 300ns, see
"Table 61 — Refresh parameters by device density" of JESD79-3E.
tXS(min) is max(5nCK, tRFC(min) + 10ns).
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
i.MX 6SoloLite only supports MMDC0, so do not access MMDC1 for i.MX 6SL.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
To i.MX6SX/UL, two ethernet interfaces are supported.
Add ENET2 clock support:
1. Introduce a new input parameter "fec_id", only 0 and 1 are allowed.
To value 1, only i.MX6SX/UL can pass the check.
2. Modify board code who use this api to follow new api prototype.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Nikolaos Pasaloukos <Nikolaos.Pasaloukos@imgtec.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Move TARGET_xx Kconfig option based on mx6 to arch/arm/cpu/armv7/mx6/Kconfig.
Add enable "CONFIG_ARCH_MX6" for boards based on mx6.
Then we can choose target boards using "make ARCH=arm menuconfig"
with ARCH_MX6 defined.
If using original way, we have no chance to enable ARCH_MX6 when
"make menuconfig". Even define CONFIG_ARCH_MX6=y in xx_defconfig,
kconfig will complains "arch/../configs/platinum_titanium_defconfig:3:
warning: override: TARGET_PLATINUM_TITANIUM changes choice state"
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Eric Bénard <eric@eukrea.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Soeren Moch <smoch@web.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Soeren Moch <smoch@web.de>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Stout is an entry level development board based on R-Car H2 SoC (R8A7790)
This commit supports the following peripherals:
- SCIFA, I2C, Ethernet, QSPI, SDHI0/2, CPLD
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
On the A31s the RTC is by default secured. Thus when u-boot
loads the kernel in non-secure world, the RTC is unavailable. The
SoC has a TrustZone Protection Controller, which can be used to
enable non-secure access to the RTC.
On the A31 the TZPC doesn't seem to do anything, i.e. changes to
its register contents do not affect access to the RTC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Now that we have separate function to enable USB clocks, remove
enabling USB clocks from enable_basic_clocks(). Now board_usb_init()
should take care to invoke enable_usb_clocks() for enabling
USB clocks.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Added functions to enable and disable USB clocks which can be invoked
during USB init and USB exit respectively.
Cc: Roger Quadros <rogerq@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Added functions to enable and disable USB clocks which can be invoked
during USB init and USB exit respectively.
Cc: Roger Quadros <rogerq@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enabled clocks for the second dwc3 controller and second USB PHY present in
DRA7.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The SYS_BOOT-based fallback shouldn't only check for one of the conditions of
use and then let the switch/case handle each boot device without enforcing the
conditions for each type of boot device again.
For instance, this behaviour would trigger the fallback for UART when
BOOT_DEVICE_UART is defined, CONFIG_SPL_YMODEM_SUPPORT is enabled (which should
be a show-stopper) and e.g. BOOT_DEVICE_USB is enabled and not
CONFIG_SPL_USB_SUPPORT.
Separating the logic for USB and UART solves this.
In addition, this adds support for more peripheral devices (USBETH and CPGMAC)
to the fallback mechanism. Note that the USBETH boot device should always be
different from the USB boot device (each should match a different bootrom
handoff case).
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Tested-by: Hannes Schmelzer <oe5hpm@oevsv.at>
DP83865 ethernet phy used on DRA74x-evm is quirky and the datasheet
provided IODELAY values for standard RGMII phys do not work.
Silicon Revision(SR) 2.0 provides an alternative bit configuration
that allows us to do a "gross adjustment" to launch the data off a
different internal clock edge. Manual IO Delay overrides are still
necessary to fine tune the clock-to-data delays. This is a necessary
workaround for the quirky ethernet Phy we have on the platform.
NOTE: SMA registers are spare "kitchen sink" registers that does
contain bits for other workaround as necessary as well. Hence the
control for the same is introduced in a generic SoC specific, board
generic location.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add support for detection of ES2.0 version of DRA7 family of
processors. ES2.0 is an incremental revision with various fixes
including the following:
- reset logic fixes
- few assymetric aging logic fixes
- MMC clock rate fixes
- Ethernet speed fixes
- edma fixes for mcasp
[ravibabu@ti.com: posted internal for an older bootloader]
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
As we discussed a couple of times, negative CONFIG options make our
life difficult; CONFIG_SYS_NO_FLASH, CONFIG_SYS_DCACHE_OFF, ...
and here is another one.
Now, there are three boards enabling OF_CONTROL on SPL:
- socfpga_arria5_defconfig
- socfpga_cyclone5_defconfig
- socfpga_socrates_defconfig
This commit adds CONFIG_SPL_OF_CONTROL for them and deletes
CONFIG_SPL_DISABLE_OF_CONTROL from the other boards to invert
the logic.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Adds functions to enable and disable edma3 clocks which can be invoked
by drivers using edma3 to control the clocks.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Adds functions to enable and disable edma3 clocks which can be invoked
by drivers using edma3 to control the clocks.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Add do_disable_clocks() to disable clock domains and module clocks.
These clocks are enabled using do_enable_clocks().
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Add do_disable_clocks() to disable clock domains and module clocks.
These clocks are enabled using do_enable_clocks().
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Move arch/arm/cpu/armv7/exynos/* to arch/arm/mach-exynos/* to allow
reuse of existing code for ARMv8 based Exynos platforms.
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add support for the mipi pll, this is necessary for getting higher dotclocks
with lcd panels.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
We now have the CONFIG_SPL_DM for code within SPL to toggle caring about
DM or not. Without this change platforms that do enable CONFIG_DM but
not CONFIG_SPL_DM may be broken (such as OMAP5).
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Signed-off-by: Tom Rini <trini@konsulko.com>
The "method" parameter was part of the original port of the driver from
the kernel. At some point this may have been added to allow for future
differentiation (as omap1 and omap2 have different GPIO IP blocks, so
this wasn't an unreasonable thing to do). At this point however it's
just extra overhead, so drop.
Signed-off-by: Tom Rini <trini@konsulko.com>
- Re-sync DT files for am33xx with Linux Kernel v4.1
- Include DT file now for the "AM335x GP EVM" and build target for it,
via device tree and DM.
- We only need to provide platform data for UART when OF_CONTROL isn't
also enabled really. We can just push GPIO to coming from DT
Signed-off-by: Tom Rini <trini@konsulko.com>
Add spi clock to the list of am43xx basic clocks to make the SPI
subsystem available on am43xx systems.
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Jagan Teki <jteki@openedev.com>
DRA72x processor variants are single core and it does not export ACP[1].
Hence, we have no source for generating an external snoop requests which
appear to be key to the deadlock in DRA72x design.
Since we build the same image for DRA74x and DRA72x platforms, lets
runtime detect and disable the workaround (in favor of performance) on
DRA72x platforms.
[1] http://infocenter.arm.com/help/topic/com.arm.doc.ddi0438i/BABIAJAG.html
Suggested-by: Richard Woodruff <r-woodruff2@ti.com>
Suggested-by: Brad Griffis <bgriffis@ti.com>
Reviewed-by: Brad Griffis <bgriffis@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Add workaround for Cortex-A15 ARM erratum 801819 which says in summary
that "A livelock can occur in the L2 cache arbitration that might
prevent a snoop from completing. Under certain conditions this can
cause the system to deadlock. "
Recommended workaround is as follows:
Do both of the following:
1) Do not use the write-back no-allocate memory type.
2) Do not issue write-back cacheable stores at any time when the cache
is disabled (SCTLR.C=0) and the MMU is enabled (SCTLR.M=1). Because it
is implementation defined whether cacheable stores update the cache when
the cache is disabled it is not expected that any portable code will
execute cacheable stores when the cache is disabled.
For implementations of Cortex-A15 configured without the “L2 arbitration
register slice” option (typically one or two core systems), you must
also do the following:
3) Disable write-streaming in each CPU by setting ACTLR[28:25] = 0b1111
So, we provide an option to disable write streaming on OMAP5 and DRA7.
It is a rare condition to occur and may be enabled selectively based
on platform acceptance of risk.
Applies to: A15 revisions r2p0, r2p1, r2p2, r2p3 or r2p4 and REVIDR[3]
is set to 0.
Note: certain unicore SoCs *might* not have REVIDR[3] not set, but
might not meet the condition for the erratum to occur when they donot
have ACP (Accelerator Coherency Port) hooked to ACE (AXI Coherency
Extensions). Such SoCs will need the work around handled in the SoC
specific manner, since there is no ARM generic manner to detect such
configurations.
Based on ARM errata Document revision 18.0 (22 Nov 2013)
Suggested-by: Richard Woodruff <r-woodruff2@ti.com>
Suggested-by: Brad Griffis <bgriffis@ti.com>
Reviewed-by: Brad Griffis <bgriffis@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Current many cpu use the same flush_cache() function, which just call
the flush_dcache_range().
So implement a weak flush_cache() for all the cpus to use.
In original weak flush_cache() in arch/arm/lib/cache.c, there has some
code for ARM1136 & ARM926ejs. But in the arch/arm/cpu/arm1136/cpu.c and
arch/arm/cpu/arm926ejs/cache.c, there implements a real flush_cache()
function as well. That means the original code for ARM1136 & ARM926ejs
in weak flush_cache() of arch/arm/lib/cache.c is totally useless.
So in this patch remove such code in flush_cache() and only call
flush_dcache_range().
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Since some driver like ohci, lcd used dcache functions. But some ARM
cpu don't implement the invalidate_dcache_range()/flush_dcache_range()
functions.
To avoid compiling errors this patch adds an weak empty stub function
for all ARM cpu in arch/arm/lib/cache.c.
And ARM cpu still can implemnt its own cache functions on the cpu folder.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The LG Optimus Black (P970) codename sniper is a smartphone that was designed
and manufactured by LG Electronics (LGE) and released back in 2011.
It is using an OMAP3630 SoC GP version, which allows running U-Boot and the
U-Boot SPL from the ground up. This port is aimed at running an Android version
such as Replicant, the fully free Android distribution. However, support for
upstream Linux with device-tree and common GNU/Linux distros boot commands
could be added in the future.
For more information about the journey to freeing this device, please read the
series of blog posts at:
http://code.paulk.fr/article20/a-hacker-s-journey-freeing-a-phone-from-the-ground-up-first-part
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Add CONFIG_OF_SUPPORT]
Signed-off-by: Tom Rini <trini@konsulko.com>
Reboot mode is written in scratchpad memory before reboot in the form of a
single char, that is the first letter of the reboot mode string as passed to the
reboot function.
This mechanism is supported on OMAP3 both my the upstream kernel and by various
TI kernels.
It is up to each board to make use of this mechanism or not.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
USB devices are not really designed to get the power bounced off and on
at them. Esp. USB powered harddisks do not like this.
Currently we power off the USB ports both on a "usb reset" and when
booting the kernel, causing the usb-power to bounce off and then back
on again.
This patch removes the powering off calls, fixing the undesirable power
bouncing.
Note this requires some special handling for the OTG port:
1) We must skip the external vbus check if we've already enabled our own
vbus to avoid false positives
2) If on an usb reset we no longer detect that the id-pin is grounded, turn
off vbus as that means an external vbus may be present now
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Spring is the first ARM-based HP Chromebook 11. It is similar to snow
and it uses the same Samsung Exynos5250 chip. But has some unusual
features. Mainline support for it has lagged snow (both in kernel and
U-Boot). Now that the exynos5 code is common we can support spring just
by adding a device tree and a few lines of configuration.
Signed-off-by: Simon Glass <sjg@chromium.org>
Line up the display with the line below, e.g.:
CPU: Exynos5250 @ 1.7 GHz
Model: Google Spring
DRAM: 2 GiB
MMC: EXYNOS DWMMC: 0
Also show the speed as GHz where appropriate.
Signed-off-by: Simon Glass <sjg@chromium.org>
As a debugging aid, allow UART3 to be used as a debug UART in SPL. This
is a precursor to proper UART support, which requires a substantial
refactor.
Signed-off-by: Simon Glass <sjg@chromium.org>
USB-related options are usually prefixed with CONFIG_USB and platform-specific
adaptation for the MUSB controller already have a CONFIG_USB_MUSB prefix, so
this switches all MUSB-related options to a CONFIG_USB_MUSB prefix, for
consistency.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Bootrom will put cpus into WFE state when boot cpu release cpus, so
target cpu cannot correctly go to spin state.
Add 'sev' to wakeup non-boot cpu that hold on bootrom space, let target
cpu can fall into u-boot spin table.
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
1. Define two structures mx6ul_iomux_ddr_regs and mx6ul_iomux_grp_regs.
2. Add a new function mx6ul_dram_iocfg to configure dram io.
3. Refactor MMDC1 macro, discard "#ifdef CONFIG_MX6SX". Since
only mmdc0 channel exists on i.MX6SX/UL, redefine MMDC1 macro support
runtime check, but not hardcoding #ifdef macros.
4. Introduce mx6ul-ddr.h, which includes the register address for DRAM
IO configuration.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
1.Update WDOG settings.
2.No need to gate/ungate all PFDs for i.MX6UL.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
i.MX6UL features an Cortex-A7 core, it does not have PL310 as other i.MX6
chips. To Cortex-A7 core, If D-Cache is enabled, L2 Cache is enabled.
There is on specific switch for on/off L2 Cache, so default select
SYS_L2CACHE_OFF.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
1. Add enet, uart, i2c, ipg clock support for i.MX6UL.
2. Correct get_periph_clk, it should account for
MXC_CCM_CBCDR_PERIPH_CLK2_PODF_MASK.
3. Refactor get_mmdc_ch0_clk to make all i.MX6 share one function,
but not use 'ifdef'.
4. Use CONFIG_FSL_QSPI for enable_qspi_clk, but not #ifdef CONFIG_MX6SX.
5. Use CONFIG_PCIE_IMX for pcie clock settings, use CONFIG_CMD_SATA for
sata clock settings. In this way, we not need "#if defined(CONFIG_MX6Q)
|| defined....", only need one CONFIG_PCIE_IMX in header file.
Signed-off-by: Ye.Li <B37916@freescale.com>
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
CPU_V7 is already selected by ARCH_MX6, so no point in selecting it again
by boards that depend on ARCH_MX6.
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
cm-fx6 is an MX6 based board, and the menuconfig hierarchy should
reflect that. Make TARGET_CM_FX6 dependant on ARCH_MX6.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
The i.MX6DQP has a PRG module, need to enable its clock for using IPU.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Brown Oliver <B37094@freescale.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Since the i.MX6QP has fixed the issue in boot ROM, so remove the workaround
for i.MX6QP.
Signed-off-by: Ye.Li <B37916@freescale.com>
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Since i.MX6QP changes some CCM registers, so modify the clocks settings to
follow the hardware changes.
In c files, use runtime check and discard #ifdef.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Add cpu type for i.MX6QP/DP.
This patch also fix is_mx6dqp(), since get_cpu_rev can return MXC_CPU_MX6QP
and MXC_CPU_MX6DP, we should use:
(is_cpu_type(MXC_CPU_MX6QP) || is_cpu_type(MXC_CPU_MX6DP)).
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Because the top-level Makefile forces all the source files
to include include/linux/kconfig.h (see the UBOOTINCLUDE define),
these includes are redundant.
By the way, there are exceptions for the statement above; host
programs. In fact, host tools in U-Boot depend on a particular
board configuration, although I think they should not. So, some
files still include <linux/config.h> to work around build errors
on host tools.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Simon Glass <sjg@chromium.org>
All am33xx device tree are using device-tree, so get_board_rev is never actually
called. Thus, we can get rid of it to make the code easier to maintain.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
Despite being defined with __weak, this declaration of get_board_rev will
conflict with the fallback one when ONFIG_REVISION_TAG is not defined.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
This introduces code to read the value of the SYS_BOOT pins on the OMAP5, as
well as the memory-preferred scheme for the interpretation of each value.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
This introduces code to read the value of the SYS_BOOT pins on the OMAP4, as
well as the memory-preferred scheme for the interpretation of each value.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
This introduces code to read the value of the SYS_BOOT pins on the OMAP3, as
well as the memory-preferred scheme for the interpretation of each value.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
OMAP devices might boot from peripheral devices, such as UART or USB.
When that happens, the U-Boot SPL tries to boot the next stage (complete U-Boot)
from that peripheral device, but in most cases, this is not a valid boot device.
This introduces a fallback option that reads the SYS_BOOT pins, that are used by
the bootrom to determine which device to boot from. It is intended for the
SYS_BOOT value to be interpreted in the memory-preferred scheme, so that the
U-Boot SPL can load the next stage from a valid location.
Practically, this options allows loading the U-Boot SPL through USB and have it
load the next stage according to the memory device selected by SYS_BOOT instead
of stalling.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Now that SPL boot devices are clearly defined, we can use BOOT_DEVICE_QSPI_4
instead of a hardcoded value.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
This introduces OMAP3 support for the common omap boot code, as well as a
major cleanup of the common omap boot code.
First, the omap_boot_parameters structure becomes platform-specific, since its
definition differs a bit across omap platforms. The offsets are removed as well
since it is U-Boot's coding style to use structures for mapping such kind of
data (in the sense that it is similar to registers). It is correct to assume
that romcode structure encoding is the same as U-Boot, given the description
of these structures in the TRMs.
The original address provided by the bootrom is passed to the U-Boot binary
instead of a duplicate of the structure stored in global data. This allows to
have only the relevant (boot device and mode) information stored in global data.
It is also expected that the address where the bootrom stores that information
is not overridden by the U-Boot SPL or U-Boot.
The save_omap_boot_params is expected to handle all special cases where the data
provided by the bootrom cannot be used as-is, so that spl_boot_device and
spl_boot_mode only return the data from global data.
All of this is only relevant when the U-Boot SPL is used. In cases it is not,
save_boot_params should fallback to its weak (or board-specific) definition.
save_omap_boot_params should not be called in that context either.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
On some boards the otg is wired up in host-only mode in this case we
have no vbus-det gpio.
Stop logging an error from sunxi_usb_phy_vbus_detect() in this case, and
stop treating sunxi_usb_phy_vbus_detect() returning a negative errno, as
if a charger is plugged into the otg port.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add support for reading the id pin value of the otg connector to the usb
phy code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Make possible using a single `u-boot-sunxi-with-spl.bin` binary for both NAND
memory and SD card. Detection where SPL was read from is implemented in
`spl_boot_device`.
Signed-off-by: Daniel Kochmański <dkochmanski@turtle-solutions.eu>
CC: Roy Spliet <r.spliet@ultimaker.com>
Cc: Ian Campbell <ijc@hellion.org.uk>
[hdegoede@redhat.com: Some small coding style fixes]
Acked-by: Hans De Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
USB download gadget functions such as thor and dfu have a separate config option
for the USB gadget part of the code, independent from the command part.
This switches the fastboot USB gadget to the same scheme, for better
consistency.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Test HW: Odroid_XU3 (Exynos5422), trats (Exynos4210)
Base on PSCI services, implement CPU_ON/CPU_OFF for ls102xa platform.
Tested on LS1021AQDS, LS1021ATWR.
Test CPU hotplug times: 60K
Test kernel boot times: 1.2K
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Acked-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
timer_wait is moved from sunxi/psci_sun7i.S, and it can be converted
completely into a reusable armv7 generic timer. LS1021A will use it
as well.
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: York Sun <yorksun@freescale.com>
As the function 'sprintf' does not check buffer boundaries but outputs
to the buffer 'enet' of fixed size (16), this patch removes the function
'sprintf', and uses 'strcpy' instead. It will assign the character
arrays 'enet' and 'phy' the corresponding character strings.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
hab_status command returns a memory dump of the hab event log. But the
raw data is not human-readable. Parsing such data into readable event
will help to minimize debbuging time.
Signed-off-by: Ulises Cardenas <Ulises.Cardenas@freescale.com>
Add I2C4 clock support for i.MX6SX. Since we use runtime check,
but not macro, we need to remove `#ifdef ..` in crm_regs.h, or
gcc will fail to compile the code succesfully.
Making the macros only for i.MX6SX open to other i.MX6x maybe not
a good choice, but we have runtime check.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
enable_spi_clock does the same thing with enable_cspi_clock, so
remove enable_cspi_clock.
Remove enable_cspi_clock prototype in header file
convert cm_fx6/spl.c to use enable_spi_clk
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
The A33 adds a pinmux function for UART0 in the PB pin group.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The original code was configuring the external pins after enabling
the R_PIO clock, which meant the configuration never made it to
the pin controller the first time in SPL.
Why this was working before is uncertain. Maybe the state was left
from a previous boot sequence, or RSB just happened to be the default
configuration. However with some A33 chips, SPL failed to configure
the PMIC. This was seen by me and Maxime on the Sinlinx SinA33 dev
board.
Reordering the calls fixed this.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Commit 487b327 ("sunxi: GPIO pin mux hardware-feature-specific function
index defines") renamed all GPIO index defines, but missed the PORT F
UART0 setup functions.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
stv0991 has cadence qspi controller for flash interfacing, this
patch configures the device pads & clock for the controller.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
This reverts commit f76eba38b3.
This patch did not have a full and proper copyright/S-o-b chain.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Conflicts:
include/configs/sun6i.h
include/configs/sun8i.h
The DIGPROG register map:
23 ------- 16 | 15 ------ 8 | 7 --- 0 |
Major upper | Major Lower | Minor |
We also need to account for Major Lower.
Signed-off-by: Ye.Li <B37916@freescale.com>
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
This is the first patch to remove the
CONFIG_SYS_EXTRA_OPTIONS.
This patch implements CPU type selection from Kconfig.
Further Kconfig stuff is added later.
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
Some archs/boards specify their own default by pre-defining the config
which causes the Kconfig system to mix up the order of the configs in
the defconfigs... This will cause merge pain if allowed to proliferate.
Remove the configs that behave this way from the archs.
A few configs still remain, but that is because they only exist as
defaults and do not have a proper Kconfig entry. Those appear to be:
SPIFLASH
DISPLAY_BOARDINFO
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates,
drop DM_USB from MSI_Primo81 as USB_MUSB_SUNXI isn't converted yet to DM]
Signed-off-by: Tom Rini <trini@konsulko.com>
DRA7/AM57xx devices can be operated in many different configurations.
When the SoC is supposed to support a configuration where low power mode
state may involve the SoC completely powered off and DDR is in self
refresh, SoC EMIF controller should not be the master of the reset
signal and an external entity might be in control of things.
The default configuration of Linux on TI evms involve not powering off
the voltage rails (due to various reasons including reliability concerns)
and must not allow DDR reset to be controlled by EMIF. On platforms
where external entity might control the reset signal, this configuration
will be a "dont care".
Fixes: 536d874708 ("ARM: DRA7: Update DDR IO registers")
Tested-by: Keerthy <j-keerthy@ti.com>
Acked-by: Brad Griffis <bgriffis@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Currently on sun6i after a "reset" the prompt returns and the user can
even type stuff until the watchdog triggers and does the actual reset.
This is somewhat unexpected behavior for the "reset" command, this
commit adds an endless loop to wait for the watchdog to trigger so that
we do not return to the prompt.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Unlike OMAP5, EMIF PHY used in DRA7 will be left in unknown state after
warm reset, emif needs to be configured to bring it back to a known
state. So configure EMIF during warm reset.
Reported-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The recent changes for hw leveling on am33xx were not intended for
DDR2 boards, only DDR3. Update emif_sdram_type to take a sdram_config
value to check against. This lets us pass in the value we would use to
configure, when we have not yet configured the board yet. In other cases
update the call to be as functional as before and check an already
programmed value in.
Tested-by: Yan Liu <yan-liu@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
On AM57xx evm I2C5 is used to detect the LCD board by reading the
EEPROM present on the bus.
Enable i2c5 clocks to help that.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
In addition to the regular mux configuration, certain pins of DRA7
require to have "manual mode" also programmed, when predefined
delay characteristics cannot be used for the interface.
struct iodelay_cfg_entry is introduced for populating
manual mode IO timings.
For configuring manual mode, along with the normal pad
configuration do the following steps:
- Select MODESELECT field of each assocaited PAD.
CTRL_CORE_PAD_XXX[8]:MODESELECT = 1(Enable MANUAL_MODE macro along with mux)
- Populate A_DELAY, G_DELAY values that are specified in DATA MANUAL.
And pass the offset of the CFG_XXX register in iodelay_cfg_entry.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
On DRA7, in addition to the regular muxing of pins, an additional
hardware module called IODelay which is also expected to be
configured. This "IODelay" module has it's own register space that is
independent of the control module.
It is advocated strongly in TI's official documentation considering
the existing design of the DRA7 family of processors during mux or
IODelay recalibration, there is a potential for a significant glitch
which may cause functional impairment to certain hardware. It is
hence recommended to do muxing as part of IOdelay recalibration.
IODELAY recalibration sequence:
- Complete AVS voltage change on VDD_CORE_L
- Unlock IODLAY config registers.
- Perform IO delay calibration with predefined values.
- Isolate all the IOs
- Update the delay mechanism for each IO with new calibrated values.
- Configure PAD configuration registers
- De-isolate all the IOs.
- Relock IODELAY config registers.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
do_set_mux32() is redefined in dra7xx and beagle_x15 boards.
IO delay recalibration sequence also needs this.
Making it generic to avoid duplication.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
When DLL_CALIB_INTERVAL is set, an extra delay is added
which is not required and it consumes EMIF bandwidth.
So making the DLL_CALIB_CTRL[8:0]DLL_CALIB_INTERVAL bits to 0.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
DDRIO_2 and LPDDR2CH1_1 registers are not present
for DRA7. So not configuring these registers for DRA7xx
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Updating EMIF registers to enable HW leveling
on DRA72-evm.
Also updating the timing registers.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
DRA7 EMIF supports Full leveling for DDR3.
Adding support for the Full leveling sequence.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
We plan to enable device tree in SPL by default. Before doing this,
explicitly disable it for all boards.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function is used before jumping to U-Boot, but in that case we don't
always want to disable caches.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
This fixes ethernet no longer working on boards which use a gpio to enable
the phy.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Before this commit the code for determining the disconnect threshold was
checking for sun4i or sun6i assuming that those where the exception and
that newer SoCs use a disconnect threshold of 2 like sun7i does.
But it turns out that newer SoCs actually use a disconnect threshold of 3
and sun5i and sun7i are the exceptions, so check for those instead.
Here are the settings from the various Allwinner SDK sources:
sun4i-a10: USBC_Phy_Write(usbc_no, 0x2a, 3, 2);
sun5i-a13: USBC_Phy_Write(usbc_no, 0x2a, 2, 2);
sun6i-a31: USBC_Phy_Write(usbc_no, 0x2a, 3, 2);
sun7i-a20: USBC_Phy_Write(usbc_no, 0x2a, 2, 2);
sun8i-a23: USBC_Phy_Write(usbc_no, 0x2a, 3, 2);
sun8i-h3: USBC_Phy_Write(usbc_no, 0x2a, 3, 2);
sun9i-a80: USBC_Phy_Write(usbc_no, 0x2a, 3, 2);
Note this commit makes no functional changes for sun4i - sun7i, and
changes the disconnect threshold for sun8i to match what Allwinner uses.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
This updates r8a7790 QoS to revision 0.973.
This commit can changed from KConfig to fit contents of the QoS.
Signed-off-by: Kouei Abe <kouei.abe.cp@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
sun8i can share the PSCI backend with sun6i. Only difference
is sun8i does not have CPU power clamp controls.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This adds PSCI support for sun6i. So far it only supports
the PWR_ON method.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The PSCI code only works for sun7i. Rename it with _sun7i suffix,
and build only if building for sun7i.
This paves the way for adding PSCI support for other platforms.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The PSCI CPU_ON code accesses quite a few registers. Document
their names to make it easier to cross reference.
Also explain "lock cpu" and "unlock cpu" as enabling/disabling
debug access.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This commit adds support to the sunxi SPL to load u-boot from the internal
NAND. Note this only adds support to access the boot partitions to load
u-boot, full NAND support to load the kernel, etc. from the nand data
partition will come later.
Signed-off-by: Roy Spliet <r.spliet@ultimaker.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add initial sun9i (A80) support, only uart + mmc are supported for now.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The latest versions of the fel tool support loading normal u-boot builds
directly, and this is now the preferred way to use the fel boot method.
This commit removes support for the old deprecated standalone fel builds.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Unlike the A31 and the A23 the A33 actually has a SID inside the SoC again,
but sid[3] is 0 (at least on some SoCs), so it is better to use the axp221
sid.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Make DRAM_ODT_EN Kconfig setting a bool, add a separate DRAM_ODT_CORRECTION
setting for A23 SoCs and use DRAM_ODT_EN Kconfig everywhere instead of
only in dram_sun4i.c and hardcoding odt_en elsewhere.
Note this commit makes no functional changes for existing boards,
its purpose is to allow changing the odt_en value on future A33 boards.
For sun4i/sun5i/sun7i boards which set DRAM_ODT_EN=y (which no defconfigs
currently do) this patch turns on odt for both the DQ and the DQS lines,
whereas previously it was possibly (but not desirable) to turn odt on only
for one of them by setting the in DRAM_ODT_EN option to 1 or 2 instead of 3.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
When porting the allwinner dram init code to u-boot we missed some code
setting an extra bit when doing auto dram config.
This commits add this bit, fixing dram init not working on the ga10h
10" a33 tablet which I'm bringing up atm.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add support for UART2 (2-pin version but note that RTS/CTS pins are available
pn that port for possible future use), can be selected in config
by using CONFIG_CONS_INDEX=3
Signed-off-by: Laurent Itti <laurentitti@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The MX6 has a temperature grade defined by OCOTP_MEM0[7:6] which is at 0x480
in the Fusemap Description Table in the reference manual. Return this value
as well as min/max temperature based on the value.
Note that the IMX6SDLRM and the IMX6SXRM do not indicate this in the
their Fusemap Description Table however Freescale has confirmed that these
eFUSE bits match the description within the IMX6DQRM and that they will
be added to the next revision of the respective reference manuals.
This has been tested with IMX6 Automative and Industrial parts.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The IMX6 has four different speed grades determined by eFUSE SPEED_GRADING
indicated by OCOTP_CFG3[17:16] which is at 0x440 in the Fusemap Description
Table. Return this frequency so that it can be used elsewhere.
Note that the IMX6SDLRM and the IMX6SXRM do not indicate this in the
their Fusemap Description Table however Freescale has confirmed that these
eFUSE bits match the description within the IMX6DQRM and that they will
be added to the next revision of the respective reference manuals.
These have been tested with IMX6 Quad/Solo/Dual-light 800Mhz and 1GHz grades.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Commit fa8b7d66f49f0c7bd41467fe78f6488d8af6976a introduced fast-exit support
to the MMDC however enabling it on the DDR3 got missed. Make sure we enable
it on the DDR3 as well.
Gateworks uses Micron memory as well as Winbond in MX6. We have found in
testing that we need to enable fast-exit for Winbond stability. Gateworks
boards are currently the only boards using the MX6 SPL and enabling
fast-exit mode.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Having bit 22 cleared in the PL310 Auxiliary Control register (shared
attribute override enable) has the side effect of transforming Normal
Shared Non-cacheable reads into Cacheable no-allocate reads.
Coherent DMA buffers in Linux always have a Cacheable alias via the
kernel linear mapping and the processor can speculatively load cache
lines into the PL310 controller. With bit 22 cleared, Non-cacheable
reads would unexpectedly hit such cache lines leading to buffer
corruption.
This was inspired by a patch from Catalin Marinas [1] and also from recent
discussions in the linux-arm-kernel list [2] where Russell King and Rob Herring
suggested that bootloaders should initialize the cache.
[1] http://lists.infradead.org/pipermail/linux-arm-kernel/2010-November/031810.html
[2] https://lkml.org/lkml/2015/2/20/199
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
This is proposal for clamping the MMDC/DDR3 clocks to the maximum supported
frequencies as per imx6 SOC models, and for dynamically calculating valid
clock value based on mem_speed.
Currently the code uses impossible values for mem_speed (1333, 1600 MT/s) for
calculating the DDR timings, and uses fixed clock (528 or 400 MHz) which
doesn't take into account DDR3 memory limitations.
Signed-off-by: Nikolay Dimitrov <picmaster@mail.bg>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Upstream Linux is broken with default configs when PSCI, thus non-secure
mode is enabled. So the user should explicitly enable this mode, e.g.
when she disabled CONFIG_CPU_IDLE in Linux (in which case it's safe to
use). We can revert this workaround once Linux got fixed.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
These registers can be used to prevent non-secure world from accessing a
megabyte aligned region of RAM, use them to protect the u-boot secure monitor
code.
At first I tried to do this from s_init(), however this inexplicably causes
u-boot's networking (e.g. DHCP) to fail, while networking under Linux was fine.
So instead I have added a new weak arch function protect_secure_section()
called from relocate_secure_section() and reserved the region there. This is
better overall since it defers the reservation until after the sec vs. non-sec
decision (which can be influenced by an envvar) has been made when booting the
os.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
[Jan: tiny style adjustment]
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Tested-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Tegra boards will have to initialize power management for the PSCI
support this way.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
In this case the secure code lives in RAM, and hence the memory node in
the device tree needs to be adjusted. This avoids that the OS will map
and possibly access the reservation.
Add support for setting CONFIG_ARMV7_SECURE_RESERVE_SIZE to carve out
such a region. We only support cutting off memory from the beginning or
the end of a RAM bank as we do not want to increase their number (which
would happen if punching a hole) for simplicity reasons
This will be used in a subsequent patch for Jetson-TK1.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Use a per-CPU variable for saving the target PC during CPU_ON
operations. This allows us to run this service independently on targets
that have more than 2 cores and also core-local power control.
CC: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Tested-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This algorithm will be useful on Tegra as well, plus we will need it for
making _psci_target_pc per-CPU.
CC: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Tested-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Tom Warren <twarren@nvidia.com>
_sunxi_cpu_entry can be converted completely into a reusable
psci_cpu_entry. Tegra124 will use it as well.
As with psci_disable_smp, also the enabling is designed to be overloaded
in cased SMP is not controlled via ACTLR.
CC: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Tested-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Move parts of sunxi's psci_cpu_off into psci_cpu_off_common, namely
cache disabling and flushing, clrex and the disabling of SMP for the
dying CPU. These steps are apparently generic for ARMv7 and will be
reused for Tegra124 support.
As the way of disabled SMP is not architectural, though commonly done
via ACLTR, the related function can be overloaded.
CC: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Tested-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Will be required for obtaining the ID of the current CPU in shared PSCI
functions. The default implementation requires a dense ID space and only
supports a single cluster. Therefore, the functions can be overloaded in
cases where these assumptions do not hold.
CC: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Tested-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Tom Warren <twarren@nvidia.com>
CONFIG_ARMV7_VIRT depends on CONFIG_ARMV7_NONSEC, thus doesn't need to
be taken into account additionally. CONFIG_ARMV7_PSCI is only set on
boards that support CONFIG_ARMV7_NONSEC, and it only works on those.
CC: Tang Yuantian <Yuantian.Tang@freescale.com>
CC: York Sun <yorksun@freescale.com>
CC: Steve Rae <srae@broadcom.com>
CC: Andre Przywara <andre.przywara@linaro.org>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Tested-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
By making the board selections optional, every defconfig will include
the board selection when running savedefconfig so if a new board is
added to the top of the list of choices the former top's defconfig will
still be correct.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Cc: Tom Rini <trini@konsulko.com>
Because all the SOCFPGA boards define CONFIG_SPL_FRAMEWORK
(see include/configs/socfpga_common.h), u-boot.img is automatically
added to the target image list by the top Makefile.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The compiler option "-Iboard/$(VENDOR)/$(BOARD)" just exists here
for iocsr_config.c to be able to include iocsr_config.h.
Use "..." instead of <...> to include a header in the same directory.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Move arch/arm/cpu/armv7armada-xp/* -> arch/arm/mach-mvebu/*
Since this platform will be extended to support other Marvell SoC's as
well, lets rename it directly to mvebu.
This will be used by the upcoming Armada 38x suport (A38x).
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Tested-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Once we add support for the ohci controller the phy-init and phy-power-on
functions may be called twice (once by the ehci code and once by the ohci
code) protect them against this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The 2/3 usb-phys on the sunxi SoCs are really a single separate functional
block, and are modelled as such in devicetree. So once we've moved all the
sunxi usb code to the driver-model then phy_probe will be called once
for the entire block from the driver-model enumeration code.
Move to this now as this also avoids problems with phy_probe being called
multiple times once we introduce ohci support. This also allows us to get rid
of the sunxi_usb_phy_enabled_count variable as phy_probe now is guaranteed
to be called only once.
Since we're effectively rewriting the probe / remove functions, move them
to the end of the file while we are at it, as that is the most logical place
for them.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The usbc.? files now only contain usb-phy related code, rename them to make
this clear.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Rename the sunxi_usbc_foo functions to sunxi_usb_phy_bar to make it clear
that these are usb-phy functions. Also change the verbs & nouns in the suffix
to match the verbs & nouns used in the Linux kernels generic phy framework.
This patch purely renames things, it contains no functional changes.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
This is the only function left in sunxi/usbc.c which is not phy related,
so remove it.
This is a preparation patch for turning the usbc.c code into a proper
usb phy driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The sunxi "usbc" code is mostly about phy setup, but currently also sets up
the host controller clocks, which is something which really belongs in the
host controller drivers, so move it there.
This is a preparation patch for moving the sunxi ehci code to the driver
model and for adding ohci support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
All sunxi boards now use the driver-model, so remove the non driver-model
code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Modify the sunxi-emac eth driver to support driver model.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Stefan Roese <sr@denx.de>
Add support for the axp152 and axp209 PMICs to the pmic register access
helpers. This is a preparation patch for moving the axp gpio code to a
separate gpio driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Move the register helpers used to access the registers via p2wi resp.
rsb bus on the otherwise identical axp221 and axp223 pmics to a separate
file, so that they can be used by the upcoming standalone axp gpio driver
too.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The driver-model gpio functions may return another value then -1 as error,
make the sunxi usbc properly handle this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Enable full support for the A33 SoC including display, otg-usb, etc.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add support for the new second DRAM PLL found on the A33 SoC.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
This is a preparation patch for adding A33 support, which will have a
mach name of sun8i-a33.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
sun6i and newer (derived) SoCs such as the sun8i-a23, sun8i-a33 and sun9i
have a various things in common, like having separate ahb reset control
registers, the SID living inside the pmic, custom pmic busses, new style
watchdog, etc.
This commit introduces a new hidden SUNXI_GEN_SUN6I Kconfig bool which can be
used to check for these features avoiding the need for an ever growing list
of "#if defined CONFIG_MACH_SUN?I" conditionals as we add support for more
"new style" sunxi SoCs.
Note that this commit changes the behavior of the gmac and hdmi code for
sun8i and the upcoming sun9i devices. This does not matter as sun8i does
not have gmac nor hdmi, and sun9i has new hardware-blocks for these so
the old code will not work there.
Also this is intentional as if a sun8i / sun9i variant which does use the
old hwblocks shows up then the GEN_SUN6I code paths will be the right ones
to use.
For completeness this also adds a SUNXI_GEN_SUN4I bool for A10/A13/A20.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
We do not use irqs in u-boot so remove the unused irq field, and all the
#ifdef-ery around the irq initialization.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
There is no reason not to and this make the #ifdef-ery easier to read.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
This is already invoked a few cycles later in monitor mode by
_secure_monitor (_sunxi_cpu_entry calls _do_nonsec_entry which triggers
_secure_monitor via smc #0). Drop it here, it serves no purpose.
CC: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Tested-by: Ian Campbell <ijc@hellion.org.uk>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The comment line in arch/arm/cpu/armv7/zynq/config.mk says that
the option "-mfpu=neon" is necessary for compiling lowlevel_init.S.
We do not have to give it to all the source files.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Fix wrong timer calculation in get_timer_masked incase of
overflow.
This fixes the issue of getting wrong time from get_timer()
calls.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Disable all level shifters before enabling
the PS-to-PL level shifters as it would
be good to disable all level shifters before
enabling the PS-to-PL in order to ensure that
it is in proper state
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
We are about to change the location for ps7_init files, breaking the
current work-flows. It is good time to drop the legacy ps7_init.c/h
support.
Going forward, please use ps7_init_gpl.c/h all the time.
If you are still using old Xilinx tools that are only able to
generate ps7_init.c/h, rename them into ps7_init_gpl.c/h.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Suggested-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The PicoZed is a System-on-Module board which is marketed as part of
the ZedBoard/MicroZed/etc. collection. It includes a Zynq-7000
processor.
This patch adds support that covers all the variants of the PicoZed
including the SKUs with Z7010/Z7020 and Z7015/Z7030 Zynq chips. This
patch set however only covers support for the System-on-Module and does
not cover any extra components that are available on carrier boards
(except those that are fanned out of the module itself).
More information on this board, its variants and available carrier
boards is available at: http://zedboard.org/product/picozed
Signed-off-by: Nathan Rossi <nathan.rossi@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
IFC has two register pages.Till IFC version 1.4 each
register page is 4KB each.But IFC ver 2.0 register page
size is 64KB each.IFC regiters structure is break into
two viz FCM and RUNTIME.FCM(Flash control machine) registers
are defined in PAGE0 and controls IFC generic functionality.
RUNTIME registers are defined in PAGE1 and controls NAND and
GPCM funcinality.
FCM and RUNTIME structures defination is common for IFC
version 1.4 and 2.0.
Signed-off-by: Jaiprakash Singh <b44839@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Enables caches which provides a rather huge speedup of the boot loader.
Also mark the on-chip RAM as cachable since this is the area U-Boot runs
from.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Vybrid product family consists of several rather similar SoC which
can be determined by softare during boot time. This allows use of
variable ${soc} for Linux device tree files. Detect VF5xx CPU's by
reading the CPU count register. We can determine the second number
of the CPU type (VF6x0) which indicates the presence of a L2 cache.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Implemented fb_set_reboot_flag() for OMAP5 to set
an environment variable 'dofastboot' when reboot-bootloader called.
This environment variable will be checked in boot command and fastboot
will be called if the variable is set.
If the bootcmd env variable of OMAP5 common is overwritten with board-specific
command, then these changes will not apply.
This was originally intended for DRA7 platform, but now applies to all OMAP5.
Ref:
http://git.omapzoom.org/?p=repo/u-boot.git;a=commit;h=19da2e436e9806259cf1f4988b9e046ab256bf2c
Signed-off-by: Angela Stegmaier <angelabaker@ti.com>
Signed-off-by: Dileep Katta <dileep.katta@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Make it check for !CONFIG_ENV_IS_NOWHERE as we can't saveenv()
in that case]
Signed-off-by: Tom Rini <trini@konsulko.com>
This patch populates serial number environment variable from
die_id_0 and die_id_1 register values for DRA7xx boards.
The function is added in omap common code so that this can be re-used.
Serial# environment variable will be useful to show correct
information in "fastboot devices" commands.
Ref:
http://git.omapzoom.org/?p=repo/u-boot.git;a=commit;h=a6bcaaf67f6e4bcd97808f53d0ceb4b0c04d583c
Signed-off-by: Angela Stegmaier <angelabaker@ti.com>
Signed-off-by: Dileep Katta <dileep.katta@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
DDR3 has a special Precharge power-down mode: fast-exit vs slow-exit.
In slow-exit mode the DLL is off but in some quiescent state that makes it easy
to turn on again in tXPDLL cycles (about 10tCK) vs the full tDLLK (512tCK).
In fast-exist mode the DLL is maintained such that it is ready again in about
3tCK.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Remap SDRAM to 0x0, and clear OCRAM's ECC in board_init_f().
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Reviewed-by: Marek Vasut <marex@denx.de>
For SoCFGPA, use the common ARMv7 lowlevel_init. Thus, we can delete the
SoCFPGA lowlevel_init.S file.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Add the calls in the spl_board_init to enable SDRAM, timer, and UART.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Marek Vasut <marex@denx.de>
These functions will be needed for use by the SPL for enabling the
console and sdram initialization.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
Don't store it in a u32.
Don't dereference the bus address as if it were a virtual address
(fixes 284231e49a ("ahci: Support splitting of read transactions
into multiple chunks")).
Fixes crash on boot in MPC8641HPCN_36BIT target.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Vadim Bendebury <vbendeb@chromium.org>
Acked-by: York Sun <yorksun@freescale.com>
Move this to Kconfig and clean up board config files that use it. Also
rename it to CONFIG_ETH_DESIGNWARE to fit with the naming that exists
in drivers/net/Kconfig.
Signed-off-by: Simon Glass <sjg@chromium.org>
Version 1:
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
As mentioned in the previous commit, adding default values in each
Kconfig causes problems because it does not co-exist with the
"depends on" syntax. (Please note this is not a bug of Kconfig.)
We should not do so unless we have a special reason. Actually,
for CONFIG_DM*, we have no good reason to do so.
Generally, CONFIG_DM is not a user-configurable option. Once we
convert a driver into Driver Model, the board only works with Driver
Model, i.e. CONFIG_DM must be always enabled for that board.
So, using "select DM" is more suitable rather than allowing users to
modify it. Another good thing is, Kconfig warns unmet dependencies
for "select" syntax, so we easily notice bugs.
Actually, CONFIG_DM and other related options have been added
without consistency: some into arch/*/Kconfig, some into
board/*/Kconfig, and some into configs/*_defconfig.
This commit prefers "select" and cleans up the following issues.
[1] Never use "CONFIG_DM=n" in defconfig files
It is really rare to add "CONFIG_FOO=n" to disable CONFIG options.
It is more common to use "# CONFIG_FOO is not set". But here, we
do not even have to do it.
Less than half of OMAP3 boards have been converted to Driver Model.
Adding the default values to arch/arm/cpu/armv7/omap3/Kconfig is
weird. Instead, add "select DM" only to appropriate boards, which
eventually eliminates "CONFIG_DM=n", etc.
[2] Delete redundant CONFIGs
Sandbox sets CONFIG_DM in arch/sandbox/Kconfig and defines it again
in configs/sandbox_defconfig.
Likewise, OMAP3 sets CONFIG_DM arch/arm/cpu/armv7/omap3/Kconfig and
defines it also in omap3_beagle_defconfig and devkit8000_defconfig.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Convert Exynos boards over to use driver model for USB. This does not remove
any unnecessary code so far.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Commit d3cfcb3 (ARM: DRA7: Enable clocks for USB OTGSS and USB PHY)
changed the member names of prcm_regs from cm_l3init_usb_otg_ss_clkctrl
to cm_l3init_usb_otg_ss1_clkctrl and from cm_coreaon_usb_phy_core_clkctrl
to cm_coreaon_usb_phy1_core_clkctrl in order to differentiate between
the two dwc3 controllers present in dra7xx/am43xx and enabled these
clocks in enable_basic_clocks() in hw_data.c. However these clocks
continued to be enabled in board files/driver files for dwc3 host
mode functionality causing compilation break with few configs.
Fixed it here by making all the clocks enabled in enable_basic_clocks()
and removing it from board files/driver files here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
