Add get_lcd_clk and set_lcd_clk callbacks for Exynos5420 needed by
exynos video driver.
Also, configure ACLK_400_DISP1 as the parent for MUX_ACLK_400_DISP1_SUB_SEL.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Previously, we used to statically assign values for vl_col, vl_row and
vl_bpix using #defines like LCD_XRES, LCD_YRES and LCD_COLOR16.
Introducing the function exynos_lcd_early_init() would take care of this
assignment on the fly by parsing FIMD DT properties, thereby allowing us
to remove LCD_XRES and LCD_YRES from the main config file.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
There is no reason to redefine pure readl/writel functions.
So remove this redundancy.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Becuase the board select menu in arch/arm/Kconfig is too big,
move the Tegra board select menu to tegra/Kconfig.
Insert the Tegra SoC select menu between the arch select and the
board select.
Architecture select
|-- Tegra Platform (Tegra)
|- Tegra SoC select (Tegra20 / 30 / 114 / 124)
|- Board select
Consolidate also common settings (CONFIG_SYS_CPU="armv7" and
CONFIG_SYS_SOC="tegra*") and always "select" CONFIG_SPL as follows:
config TEGRA
bool
select SPL
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Cc: Tom Warren <twarren@nvidia.com>
The bcm_ep board configuration is used by a number of boards
including Cygnus and NSP.
Add builds for the bcm958300k and the bcm958622hr boards.
Signed-off-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Steve Rae <srae@broadcom.com>
The iproc architecture code is present in several Broadcom
chip architectures, including Cygnus and NSP.
Signed-off-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Steve Rae <srae@broadcom.com>
Add pin mux for NAND Flash Controller (NFC). NAND can be connected
using 8 or 16 data lines, this patch adds pin mux entries for all
16 data lines.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Enable Ethernet clock when Broadcom StarFighter2 Ethernet block
(CONFIG_BCM_SF2_ETH) is enabled.
Signed-off-by: Jiandong Zheng <jdzheng@broadcom.com>
Signed-off-by: Steve Rae <srae@broadcom.com>
Enable initialization fo designware ethernet controller. With this
patch, ethernet works in my configuration, provided I set ethernet
address in the environment.
Signed-off-by: Pavel Machek <pavel@denx.de>
To fix the build error when build for Altera dev kit, not
virtual target. At same time, set the build for Altera dev
kit as default instead virtual target. With that, U-Boot
is booting well and SPL still lack of few drivers.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Structure defining clock manager hardware was wrong, leading to
wrong registers being accessed and hang in MMC init.
This fixes structure to match hardware.
Signed-off-by: Pavel Machek <pavel@denx.de>
When compiling u-boot with W=1 the extern inline void for
read* is likely causing the most noise. gcc / clang will
warn there is never a actual declaration for these functions.
Instead of declaring these extern make them static inline so
it is actually declared.
cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
This patch reads EFUSE_BOOTROM register to see the maximum supported
clock for CORE and TETRIS PLLs and configure them accordingly.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
This patch adds support for parallel NOR device (S29GL512S10) present on J6-EVM.
The Flash device is connected to GPMC controller on chip-select[0] and accessed
as memory-mapped device. It has data-witdh=x16, capacity-64MBytes(512Mbits) and
is CFI compatible.
As multiple devices are share GPMC pins on this board, so following board
settings are required to detect NOR device:
SW5.1 (NAND_BOOTn) = OFF (logic-1)
SW5.2 (NOR_BOOTn) = ON (logic-0) /* Active-low */
SW5.3 (eMMC_BOOTn) = OFF (logic-1)
SW5.4 (QSPI_BOOTn) = OFF (logic-1)
And also set appropriate SYSBOOT configurations:
SW3.1 (SYSBOOT[ 8])= ON (logic-1) /* selects SYS_CLK1 speed */
SW3.2 (SYSBOOT[ 9])= OFF (logic-0) /* selects SYS_CLK1 speed */
SW3.3 (SYSBOOT[10])= ON (logic-1) /* wait-pin monitoring = enabled */
SW3.4 (SYSBOOT[11])= OFF (logic-0) /* device type: Non Muxed */
SW3.5 (SYSBOOT[12])= OFF (logic-0) /* device type: Non Muxed */
SW3.6 (SYSBOOT[13])= ON (logic-1) /* device bus-width: 1(x16) */
SW3.7 (SYSBOOT[14])= OFF (logic-0) /* reserved */
SW3.8 (SYSBOOT[15])= ON (logic-1) /* reserved */
Also, following changes are required to enable NOR Flash support in
dra7xx_evm board profile:
mx6sxsabresd board has 2 FEC ports, each one connected to a AR8031.
Add support for one FEC port initially.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
This allows u-boot to load different OS or Bare Metal application on
different cores of the i.MX6 SoC.
For example: running Android on cpu0 and a RT OS like QNX/FreeRTOS on cpu1.
Signed-off-by: Gabriel Huau <contact@huau-gabriel.fr>
Acked-by: Stefano Babic <sbabic@denx.de>
Do not specify own zynq specific SPL macros
because there is no need for that.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
This adds board support for the Toradex Colibri T30 module.
Working functions:
- SD card boot
- eMMC environment and boot
- USB host/USB client (on the dual role port)
- Network (via ASIX USB)
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Tom Warren <twarren@nvidia.com>
On Tegra114 and Tegra124 platforms, certain display-related registers cannot
be accessed unless the VPR registers are programmed. For bootloader, we
probably don't care about VPR, so we disable it (which counts as programming
it, and allows those display-related registers to be accessed).
This patch is based on the commit 5f499646c83ba08079f3fdff6591f638a0ce4c0c
in Chromium OS U-Boot project.
Signed-off-by: Andrew Chew <achew@nvidia.com>
Signed-off-by: Jimmy Zhang <jimmzhang@nvidia.com>
Signed-off-by: Bryan Wu <pengw@nvidia.com>
[acourbot: ensure write went through, vpr.c style changes]
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Cc: Tom Warren <TWarren@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Terje Bergstrom <tbergstrom@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The hardware DQS gate training is a bit unreliable and does not
always find the best delay settings.
So we introduce a 32-bit 'dqs_gating_delay' variable, where each
byte encodes the DQS gating delay for each byte lane. The delay
granularity is 1/4 cycle.
Also we allow to enable the active DQS gating window mode, which
works better than the passive mode in practice. The DDR3 spec
says that there is a 0.9 cycles preamble and 0.3 cycle postamble.
The DQS window has to be opened during preamble and closed during
postamble. In the passive window mode, the gating window is opened
and closed by just using the gating delay settings. And because
of the 1/4 cycle delay granularity, accurately hitting the 0.3
cycle long postamble is a bit tough. In the active window mode,
the gating window is auto-closing with the help of monitoring
the DQS line, which relaxes the gating delay accuracy requirements.
But the hardware DQS gate training is still performed in the passive
window mode. It is a more strict test, which is reducing the results
variance compared to the training with active window mode.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
It is going to be useful in more than one place.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The stale error status should be cleared for all sun4i/sun5i/sun7i
hardware and not just for sun7i. Also there are two types of DQS
gate training errors ("found no result" and "found more than one
possible result"). Both are handled now.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The sun5i hardware (Allwinner A13) introduced configurable MBUS clock
speed. Allwinner A13 uses only 16-bit data bus width to connect the
external DRAM, which is halved compared to the 32-bit data bus of sun4i
(Allwinner A10), so it does not make much sense to clock a wider
internal bus at a very high speed. The Allwinner A13 manual specifies
300 MHz MBUS clock speed limit and 533 MHz DRAM clock speed limit. Newer
sun7i hardware (Allwinner A20) has a full width 32-bit external memory
interface again, but still keeps the MBUS clock speed configurable.
Clocking MBUS too low inhibits memory performance and one has to find
the optimal MBUS/DRAM clock speed ratio, which may depend on many
factors:
http://linux-sunxi.org/A10_DRAM_Controller_Performance
This patch introduces a new 'mbus_clock' parameter for the 'dram_para'
struct and uses it as a desired MBUS clock speed target. If 'mbus_clock'
is not set, 300 MHz is used by default to match the older hardcoded
settings.
PLL5P and PLL6 are both evaluated as possible clock sources. Preferring
the one, which can provide higher clock frequency that is lower or
equal to the 'mbus_clock' target. In the case of a tie, PLL5P has
higher priority.
Attempting to set the MBUS clock speed has no effect on sun4i, but does
no harm either.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The DRAM controller allows to configure impedance either by using the
calibration against an external high precision 240 ohm resistor, or
by skipping the calibration and loading pre-defined data. The DRAM
controller register guide is available here:
http://linux-sunxi.org/A10_DRAM_Controller_Register_Guide#SDR_ZQCR0
The new code supports both of the impedance configuration modes:
- If the higher bits of the 'zq' parameter in the 'dram_para' struct
are zero, then the lowest 8 bits are used as the ZPROG value, where
two divisors encoded in lower and higher 4 bits. One divisor is
used for calibrating the termination impedance, and another is used
for the output impedance.
- If bits 27:8 in the 'zq' parameters are non-zero, then they are
used as the pre-defined ZDATA value instead of performing the ZQ
calibration.
Two lowest bits in the 'odt_en' parameter enable ODT for the DQ and DQS
lines individually. Enabling ODT for both DQ and DQS means that the
'odt_en' parameter needs to be set to 3.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Remove the duplicated argument to | in two places. Reported
by Coccinelle (http://coccinelle.lip6.fr/).
Signed-off-by: Maxin B. John <maxin.john@enea.com>
According to the Reference Manual the 'mask_periph2_clk_sel_loaded' field of
register CCM_CIMR corresponds to bit 19 so fix its definition accordingly.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
According to the Reference Manual the 'wb_per_at_lpm' field of register
CCM_CLPCR corresponds to bit 16 so fix its definition accordingly.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
According to the Reference Manual the 'spdif0_clk_podf' field of register
CCM_CDCDR corresponds to bits 22, 23 and 24, so fix the mask and offset
definitions accordingly.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
'omux' field is not used anywhere and such layout is not valid for mx6solox.
Instead of adding more ifdef's into the structure, let's simply remove this
unused 'omux' field.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
At present arm defines CONFIG_SYS_GENERIC_GLOBAL_DATA, meaning that
the global_data pointer is set up in board_init_f(). However it is
actually set up before this, it just isn't zeroed.
If we zero the global data before calling board_init_f() then we
don't need to define CONFIG_SYS_GENERIC_GLOBAL_DATA.
Make this change (on arm32 only) to simplify the init process. I
don't have the ability to test aarch64 yet.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Tom Rini <trini@ti.com>
Implement SD driver for the S3C24xx family. This implementation
is currently only capable of using the PIO transfers, DMA is not
supported.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Unify the register structure so they can be easily used across all
of S3C24xx lineup.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
This patch add Marvell kirkwood MVSDIO/MMC driver
and enable it for Sheevaplugs and OpenRD boards.
Signed-off-by: Gerald Kerma <drEagle@doukki.net>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
The commit adds three defines which will be used in
the EHCI driver to enable USB clock and assert
reset controllers of the corresponding PHYs.
Signed-off-by: Roman Byshko <rbyshko@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This enables the necessary clocks, in AHB0 and in PLL6_CFG. This is done
for sun7i only since I don't have access to any other sunxi platforms
with sata included.
The PHY setup is derived from the Alwinner releases and Linux, but is mostly
undocumented.
The Allwinner AHCI controller also requires some magic (and, again,
undocumented) DMA initialisation when starting a port. This is added under a
suitable ifdef.
This option is enabled for Cubieboard, Cubieboard2 and Cubietruck based on
contents of Linux DTS files, including SATA power pin config taken from the
DTS. All build tested, but runtime tested on Cubieboard2 and Cubietruck only.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Generate the PSCI node in the device tree.
Also add a reserve section for the "secure" code that lives in
in normal RAM, so that the kernel knows it'd better not trip on
it.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Implement core support for PSCI. As this is generic code, it doesn't
implement anything really useful (all the functions are returning
Not Implemented).
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The current non-sec switching code suffers from one major issue:
it cannot run in secure RAM, as a large part of u-boot still needs
to be run while we're switched to non-secure.
This patch reworks the whole HYP/non-secure strategy by:
- making sure the secure code is the *last* thing u-boot executes
before entering the payload
- performing an exception return from secure mode directly into
the payload
- allowing the code to be dynamically relocated to secure RAM
before switching to non-secure.
This involves quite a bit of horrible code, specially as u-boot
relocation is quite primitive.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
In order to be able to use the various mode constants (far more
readable than random hex values), add the missing HYP and A
values.
Also update arm/lib/interrupts.c to display HYP instead of an
unknown value.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The errata is applicable on all OMAP4 (4430 and 4460/4470) and OMAP5
ES 1.0 devices. The current revision check erroneously implements this
on all DRA7 varients and with DRA722 device (which has only 1 EMIF instance)
infact causes an asynchronous abort and ends up masking it in CPSR,
only to be uncovered once the kernel switches to userspace.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
This patch adds Keystone2 K2E SOC specific code to support
MSMC cache coherency. Also create header file for msmc to hold
its API.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
This patch adds clock definitions and commands to support Keystone2
K2E SOC.
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
This patch adds hardware definitions specific to Keystone II
K2E device. It has a lot common definitions with k2hk SoC, so
move them to common hardware.h. This is preparation patch for
adding K2E SoC support.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
This patch in general spit SoC type clock dependent code and general
clock code. Before adding keystone II Edison k2e SoC which has
slightly different dpll set, move k2hk dependent clock code to
separate clock-k2hk.c file.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Use KS2_ prefix in all definitions, for that replace K2HK_ prefix and
add KS2_ prefix where it's needed. It requires to change names also
in places where they're used. Align lines and remove redundant
definitions in kardware-k2hk.h at the same time.
Using common KS2_ prefix helps resolve redundant redefinitions and
adds opportunity to use KS2_ definition across a project not thinking about
what SoC should be used. It's more convenient and we don't need to worry
about the SoC type in common files, hardware.h will think about that.
The hardware.h decides definitions of what SoC to use.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
By default all DSPs are turned off, for another case option
to turn off them is added in this commit.
Also add command to turn off itself.
Acked-by: Murali Karicheri <m-maricheri2@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
It's convinient to hold ddr3 function definitions in separate file
such as ddr3.h. So move this from hardware.h to ddr3.h.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Use common keystone2 Power Sleep controller base address instead of
directly deciding which keystone2 SoC is used in psc module.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
As noted by clang, we have been shifting certain values out of 32bit
range when setting some DDR registers. Upon further inspection these
had been touching reserved fields (and having no impact). These came in
from historical bring-up code and can be discarded. Similarly, we had
been declaring some fields as 0 when they will be initialized that way.
Tested on Beaglebone White.
Reported-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Cc: Ash Charles <ash@gumstix.com>
Signed-off-by: Tom Rini <trini@ti.com>
Tested-By: Ash Charles <ashcharles@gmail.com>
Renesas R8A7794 is CPU with Cortex-A15. This supports the basic register
definition and GPIO and framework of PFC.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
On mx6solox there is an additional 0x4000 offset for the GPR registers.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
There is no need to keep iomuxc_base_regs structure as it serves the exact same
purpose of the iomuxc structure, which is to provide access to the GPR
registers.
The additional fields of iomuxc_base_regs are not used. Other advantage of
'iomuxc' is that it has a shorter name and the variable declarations can fit
into a single line.
So remove iomuxc_base_regs structure and use iomuxc instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Previously the driver was only tested on Power SoCs. Different barrier
instructions are needed for ARM SoCs.
Signed-off-by: York Sun <yorksun@freescale.com>
This patch enables CONFIG_CMD_GPIO for the Allwinner (sunxi) platform as well
as providing the common gpio API (gpio_request/free, direction in/out, get/set
etc).
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ma Haijun <mahaijuns@gmail.com>
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: Henrik Nordström <henrik@henriknordstrom.net>
Cc: Tom Cubie <Mr.hipboi@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Add support for the i2c controller found on all Allwinner sunxi SoCs,
this is the same controller as found on the Marvell orion5x and kirkwood
SoC families, with a slightly different register layout, so this patch uses
the existing mvtwsi code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-By: Prafulla Wadaskar <prafulla@marvell.com>
Acked-by: Heiko Schocher <hs@denx.de>
[ ijc -- updated u-boot-spl-fel.lds ]
Note this has only been tested on Allwinner sunxi devices (support for which
gets introduced by a later patch).
The kirkwood changes have been compile tested using the wireless_space board
config, the orion5x changes have been compile tested using the edminiv2 board
config.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heiko Schocher <hs@denx.de>
mx6solox is the newest member of the mx6 family.
Some of the new features on this variants are:
- Cortex M4 microcontroller (besides the CortexA9)
- Dual Gigabit Ethernet
Add the initial support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
The pad settings for DISP0_DATA02 and DISP0_DAT10 were not
set in the same way as DISP0_DAT00-23, causing much flicker
in parallel RGB displays on Dual-Lite and Solo processors.
These settings now match the i.MX6 Dual and Quad core versions.
Note that this fixes a regression in commit b47abc3 and that
this is the second time we've had a regression on these two
pads (See commit e654ddf).
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Newer AM437x silicon requires us to explicitly power up
the USB2 PHY. By implementing usb_phy_power() we can
achieve that.
Signed-off-by: Felipe Balbi <balbi@ti.com>
* Boot failures have been discovered due to a combination of routing issues and
non optimal ddr3 timings in the EMIF
* Since ddr3 timings are different after significant board layout changes
different timings are required for alpha, beta and production boards.
Signed-off-by: Franklin S. Cooper Jr <fcooper@ti.com>
There is no way to reset the cpu, so use the watchdog for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Fix following compilation error when CONFIG_ARM64 is defined
Error: unknown or missing system register name at operand 2
-- `mrs x0,daifmsr daifset,#3'
Signed-off-by: Shaibal.Dutta <shaibal.dutta@broadcom.com>
Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Reviewed-by: Darwin Rambo <drambo@broadcom.com>
Scan Manager driver will be called to configure the IOCSR
scan chain. This configuration will setup the IO buffer settings
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Wolfgang Denk <wd@denx.de>
CC: Pavel Machek <pavel@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
To enable the DesignWare watchdog support at SOCFPGA
Cyclone V dev kit.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
This patch returns back support for old ep93xx processors family
Signed-off-by: Sergey Kostanbaev <sergey.kostanbaev@gmail.com>
Cc: albert.u.boot@aribaud.net
This is not only more readable but also prevents a warning
about a missing prototype. The prototypes which are actually
missing are added.
cc: Albert Aribaud <albert.u.boot@aribaud.net>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Reviewed-by: Tom Rini <trini@ti.com>
LS2085A is an ARMv8 implementation. This adds board support for emulator
and simulator:
Two DDR controllers
UART2 is used as the console
IFC timing is tightened for speedy booting
Support DDR3 and DDR4 as separated targets
Management Complex (MC) is enabled
Support for GIC 500 (based on GICv3 arch)
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Arnab Basu <arnab.basu@freescale.com>
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Freescale LayerScape with Chassis Generation 3 is a set of SoCs with
ARMv8 cores and 3rd generation of Chassis. We use different MMU setup
to support memory map and cache attribute for these SoCs. MMU and cache
are enabled very early to bootst performance, especially for early
development on emulators. After u-boot relocates to DDR, a new MMU
table with QBMan cache access is created in DDR. SMMU pagesize is set
in SMMU_sACR register. Both DDR3 and DDR4 are supported.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Varun Sethi <Varun.Sethi@freescale.com>
Signed-off-by: Arnab Basu <arnab.basu@freescale.com>
Make MMU function reusable. Platform code can setup its own MMU tables.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: David Feng <fenghua@phytium.com.cn>
This is needed for accessing peripherals with 64-bit MMIO registers,
from ARMv8 processors.
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
The armv8 ARM Trusted Firmware (ATF) can be used to load various ATF
images and u-boot, and does this for virtual platforms by using
semihosting. This commit extends this idea by allowing u-boot to also
use semihosting to load the kernel/ramdisk/dtb. This eliminates the need
for a bootwrapper and produces a more realistic boot sequence with
virtual models.
Though the semihosting code is quite generic, support for armv7 in
fastmodel is less useful due to the wide range of available silicon
and the lack of a free armv7 fastmodel, so this change contains an
untested armv7 placeholder for the service trap opcode.
Please refer to doc/README.semihosting for a more detailed description
of semihosting and how it is used with the armv8 virtual platforms.
Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Cc: trini@ti.com
Cc: fenghua@phytium.com.cn
Cc: bhupesh.sharma@freescale.com
I2C read transactions are typically implemented as follows:
START(write) address REPEATED_START(read) data... STOP
However, Tegra's I2C driver currently implements reads as follows:
START(write) address STOP START(read) data... STOP
This sequence confuses at least the AS3722 PMIC on the Jetson TK1 board,
leading to corrupted read data in some cases. Fix the driver to chain
the transactions together using repeated starts to solve this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Yen Lin <yelin@nvidia.com>
Move AEMIF driver to drivers/memory/ti-aemif.c along with AEMIF
definitions collected in arch/arm/include/asm/ti-common/ti-aemif.h
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
The definitions inside emif_defs.h concern davinci nand driver and
should be in it's header. So create header file for davinci nand
driver and move definitions from emif_defs.h and nand_defs.h to it.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
[trini: Fixup more davinci breakage]
Signed-off-by: Tom Rini <trini@ti.com>
According to:
http://git.freescale.com/git/cgit.cgi/imx/uboot-imx.git/log/?h=imx_v2009.08_3.0.35_4.1.0
ENGR00287268 mx6: fix the secure boot issue on the new tapout chip
commit 424cb1a79e9f5ae4ede9350dfb5e10dc9680e90b
newer i.MX6 silicon revisions have an updated ROM and HAB API table.
Please see also:
i.MX Applications Processors Documentation
Engineering Bulletins
EB803, i.MX 6Dual/6Quad Applications Processor Silicon Revsion 1.2 to 1.3 Comparison
With this change the secure boot status is correctly displayed
Signed-off-by: Stefano Babic <sbabic@denx.de>
mx6 reference manual incorrectly states that the DEVICE_TYPE field of
IOMUXC_GPR12 register should be configured as '0010' for setting the PCI
controller in RC mode. The correct value should be '0100' instead.
This also aligns with the same value used in the mx6 pci kernel driver.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Sometimes Read DQ and DQS are not in phase. Since, this
phase shift differs from board to board, we need to
calibrate it at DRAM init phase, that's read DQ calibration.
This patch adds SW Read DQ calibration routine to compensate
this skew.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
mkconfig links ${objtree}/include/asm/proc/ to
${srctree}/arch/${arch}/include/asm/proc-armv/. This seems to be a
remnant from the past. Ever since its introduction in 2003 it is used
only in ARM build and always links to same place, so let's simplify
the code, remove it and reference directly where needed.
Successful MAKEALL for ARM and PowerPC verified on Linux.
Signed-off-by: Vasili Galka <vvv444@gmail.com>
Add QSPI support for VF610TWR, such as clock and iomux.
Signed-off-by: Alison Wang <Huan.Wang@freescale.com>
Signed-off-by: Chao Fu <b44548@freescale.com>
Similar to OMAP4/5 we need to scale the voltage up prior to changing the
clock frequencies up higher. Add a similar hook to start with.
Signed-off-by: Tom Rini <trini@ti.com>
For usage of timer6 within B&R we need this defines to enable clock
modules and clk-source.
Also the 'Timer register bits' are expanded.
By the way we add defines for all timers within AM335x SoC.
Cc: trini@ti.com
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
Currently PWREMU_MGMT is not configured in the Linux generic UART
driver as this register seems to be specific TI UART IP. So this
needs to be enabled in u-boot to use UART1 from kernel space.
Acked-By: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
OMAP3 used GPMC_NAND_ECC_LP_x8_LAYOUT and GPMC_NAND_ECC_LP_x16_LAYOUT macros
to configure GPMC controller for x7 or x8 bit device connected to its interface.
Now this information is encoded in CONFIG_SYS_NAND_DEVICE_WIDTH macro, so above
macros can be completely removed.
Signed-off-by: Pekon Gupta <pekon@ti.com>
Allow imx_iomux_v3_setup_multiple_pads to take a multi-cpu pad_list
and add macros for declaring the pad_list that take into account the
SoC types supported using CONFIG_MX6QDL (supports both the MX6Q and MX6DL
iomux).
Cc: Stefan Roese <sr@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Andy Ng <andreas2025@gmail.com>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
- add function for configuring iomux based on board-specific regs
- add function for configuring mmdc based on board-specific and
chip-specific data
Cc: Stefan Roese <sr@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Andy Ng <andreas2025@gmail.com>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Add memory-mapped structures for MMDC iomux and configuration. Note that whi
the MMDC configuration registers are common between the IMX6DQ
(IMX6DUAL/IMX6QUAD) and IMX6SDL (IMX6SOLO/IMX6DUALLITE) types the iomux
registers differ. This requires two sets of structures.
Add structures to describe DDR3 device information, system information
(memory layout, etc), and MMDC calibration registers that can be used to
configure the MMDC dynamically.
We define these structures for SPL builds instead of including mx6q-ddr.h an
mx6dl-ddr.h which use the same namespace and are only useful for imximage cf
files.
Cc: Stefan Roese <sr@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Andy Ng <andreas2025@gmail.com>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
arch/arm/include/asm/spl.h requires all SoCs to have
arch/arm/include/asm/arch-*/spl.h.
But many of them just define BOOT_DEVICE_* macros.
Those macros are used in the "switch (boot_device) { ... }"
statement in common/spl/spl.c.
So they should not be archtecture specific, but be described as
a simpile enumeration.
This commit merges most of arch/arm/include/asm/arch-*/spl.h
into arch/arm/include/asm/spl.h.
With a little more effort, arch-zynq/spl.h and arch-socfpga/spl.h
will be merged, while I am not sure about OMAP and Exynos.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Tom Warren <twarren@nvidia.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Minkyu Kang <mk7.kang@samsung.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
Acked-by: Michal Simek <monstr@monstr.eu>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Tested-by: Bo Shen <voice.shen@atmel.com> [on sama5d3xek board for at91 part]
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stefano Babic <sbabic@denx.de> [applying Tim's i.MX6 patches]
Acked-by: Tom Rini <trini@ti.com>
Setting ps_hold ought to be one of the first things we do when we
first boot up. If we wait until the main u-boot runs we won't set it
in time and the PMIC may power us back off.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
If without switch to main crystal oscillator, the sama5d3 SoC will
use internal on chip RC oscillator.
In order to get better accuracy, switch to main crystal oscillator.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
On Mon, 2014-05-05 at 14:18 +0200, Stefan Roese wrote:
> > + case 1:
> > +#if CONFIG_MMC1_PG
> Are you sure that this is correct and shouldn't be:
>
> +#ifdef CONFIG_MMC1_PG
>
> ?
It's "correct" in so far as it works (the boards.cfg config stuff
#defines things to 1), but I think you are right that it isn't the
preferred style. But...
> A quick scan through this patch series shows that this define
> is not set at all. Perhaps its outdated? Or is it used to support
> some other sunxi SoC? Not sure, perhaps it should be removed for
> now.
...I had thought that it was to support some other board which wasn't
being upstreamed right now, so eventually useful and harmless for now,
but I've just checked and it isn't actually used by any of the boards in
u-boot-sunxi.git. So rather than fix it to use #ifdef lets drop it.
Rather than resend the entire series, here is v5.1 of this patch.
> Other than this please add my:
>
> Reviewed-by: Stefan Roese <sr@denx.de>
Thanks!
8<---------------------------------
>From 20704e35a41664de5f516ed0e02981ac06085102 Mon Sep 17 00:00:00 2001
From: Ian Campbell <ijc@hellion.org.uk>
Date: Fri, 7 Mar 2014 04:29:39 +0000
Subject: [PATCH v5.1 7/8] sunxi: mmc support
This adds support for the MMC controller on the Allwinner A20 (sun7i)
processor.
Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
Signed-off-by: Luke Leighton <lkcl@lkcl.net>
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Wills Wang <wills.wang.open@gmail.com>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Tom Cubie <Mr.hipboi@gmail.com>
Cc: Aaron Maoye <leafy.myeh@allwinnertech.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Reviewed-by: Tom Rini <trini@ti.com>
This patch adds generic board, start of day and basic build system support for
the Allwinner A20 (sun7i) processor. This code will not been compiled until the
build is hooked up in a later patch. It has been split out to keep the patches
manageable.
Signed-off-by: Adam Sampson <ats@offog.org>
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Signed-off-by: Luc Verhaegen <libv@skynet.be>
Signed-off-by: Luke Leighton <lkcl@lkcl.net>
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Patrick Wood <patrickhwood@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Wills Wang <wills.wang.open@gmail.com>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Marek Vasut <marex@denx.de>
Cc: Tom Cubie <Mr.hipboi@gmail.com>
Reviewed-by: Tom Rini <trini@ti.com>
This patch adds DRAM initialisation support for the Allwinner A20 (sun7i)
processor. This code will not been compiled until the build is hooked up in a
later patch. It has been split out to keep the patches manageable.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Signed-off-by: Luke Leighton <lkcl@lkcl.net>
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Marek Vasut <marex@denx.de>
Cc: Tom Cubie <Mr.hipboi@gmail.com>
Reviewed-by: Tom Rini <trini@ti.com>
This patch adds the basic pinmux and gpio support for the Allwinner A20 (sun7i)
processor. This code will not been compiled until the build is hooked up in a
later patch. It has been split out to keep the patches manageable.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ma Haijun <mahaijuns@gmail.com>
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Henrik Nordström <henrik@henriknordstrom.net>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Tom Rini <trini@ti.com>
Acked-by: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Tom Cubie <Mr.hipboi@gmail.com>
Reviewed-by: Tom Rini <trini@ti.com>
This patch adds the basic clocks and timer support for the Allwinner A20
(sun7i) processor. This code will not been compiled until the build is hooked
up in a later patch. It has been split out to keep the patches manageable.
Some of the code here is common to multiple sunxi subarchtectures, hence files
are named sun4i which is the earliest similar variant.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Signed-off-by: Luke Leighton <lkcl@lkcl.net>
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: Stefan Roese <sr@denx.de>
Cc: Tom Cubie <Mr.hipboi@gmail.com>
Reviewed-by: Tom Rini <trini@ti.com>
Set DDR_SEL_PAD_CONTR register explicitly to DDR3 which solves RAM
issues with newer silicon (1.1). This register was added in revision
4 of the Vybrid Reference Manual.
Signed-off-by: Stefan Agner <stefan@agner.ch>
The omap_hw_init_context function (and assorted helpers) is the same for
all OMAP-derived parts as when CHSETTINGS are used, that's the same and
our DDR base is also always the same. In order to make this common we
simply need to update the names of the define for DDR address space
which is also common.
Cc: Sricharan R. <r.sricharan@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
GPMC controller on TI's OMAP SoC is general purpose controller to interface
with different types of external devices like;
- parallel NOR flash
- parallel NAND flash
- OneNand flash
- SDR RAM
- Ethernet Devices like LAN9220
Though GPMC configurations may be different for each platform depending on
clock-frequency and external device interfacing with controller. But
initialization sequence remains common across all platfoms.
Thus this patch merges gpmc_init() scattered in different arch-xx/mem.c
files into single omap-common/mem-common.c
However, actual platforms specific register config values are still sourced
from corresponding platform specific headers like;
AM33xx: arch/arm/include/asm/arch-am33xx/mem.h
OMAP3: arch/arm/include/asm/arch-omap3/mem.h
OMAP4: arch/arm/include/asm/arch-omap4/mem.h
OMAP4: arch/arm/include/asm/arch-omap5/mem.h
Also, CONFIG_xx passed by board-profile decide config for which set of macros
need to be used for initialization
CONFIG_NAND: initialize GPMC for NAND device
CONFIG_NOR: initialize GPMC for NOR device
CONFIG_ONENAND: initialize GPMC for ONENAND device
Signed-off-by: Pekon Gupta <pekon@ti.com>
[trini: define GPMC_SIZE_256M for omap3]
Signed-off-by: Tom Rini <trini@ti.com>
This patch moves platform specific information for GPMC and ELM controller
into separate header files, so that any derivative devices do not mess other
header files.
Platform specific information added into arch-xx/../hardware.h
- CPU related platform specific details like base-address of GPMC and ELM
Platform specific information added into arch-xx/../mem.h
- Generic configs for GPMC and ELM initialization.
- Hardware parameters or constrains specific to GPMC and ELM IP like;
number of max number of chip-selects available
Signed-off-by: Pekon Gupta <pekon@ti.com>
This patch moves platform specific information for GPMC and ELM controller
into separate header files, so that any derivative devices do not mess other
header files.
Platform specific information added into arch-xx/../hardware.h
- CPU related platform specific details like base-address of GPMC and ELM
Platform specific information added into arch-xx/../mem.h
- Generic configs for GPMC and ELM initialization.
- Hardware parameters or constrains specific to GPMC and ELM IP like;
number of max number of chip-selects available
Signed-off-by: Pekon Gupta <pekon@ti.com>
Conflicts:
boards.cfg
Conflicts were trivial once u-boot-arm/master boards.cfg was
reformatted (commit 6130c146) to match u-boot/master's own
reformatting (commit 1b37fa83).
Modified the mmc_set_clock for eynos4.
The goal of this patch is that fsys-div register should be reset.
And retore the div-value, not using the value of lowlevel_init.
(For using SDMMC4, this patch is needs)
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
A few changes are made to the Tegra EHCI driver so that it can set
everything up for device-mode operation on the first USB controller.
This can be used in conjunction with ci_udc.c to operate as a USB
device.
Detailed changes are:
* Rename set_host_mode() to set_up_vbus() since that's really what it
does.
* Modify set_up_vbus() to know whether it's initializing in host or
device mode, and:
- Skip the external VBUS check in device mode, since external VBUS is
expected in this case.
- Disable VBUS output in device mode.
* Modify init_phy_mux() to know whether it's initializing in host or
device mode, and hence skip setting USBMODE_CM_HC (which enables host
mode) in device mode. See the comments in that function for why this
is safe w.r.t. the ordering requirements of PHY selection.
* Modify init_utmi_usb_controller() to force "b session valid" in device
mode, since the HW requires this. This is done in UTMI-specific code,
since we only support device mode on the first USB controller, and that
controller can only talk to a UTMI PHY.
* Enhance ehci_hcd_init() to error-check the requested host-/device-mode
vs. the dr_mode (dual-role mode) value present in device tree, and the
HW configurations which support device mode.
* Enhance ehci_hcd_init() not to skip HW initialization when switching
between host and device mode on a controller. This requires remembering
which mode the last initialization used.
Cc: Jim Lin <jilin@nvidia.com>
Cc: Stefan Agner <stefan@agner.ch>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Bootmode mask was defined as 0x0F, but documentation mentions 0x07.
Experiments show that bit "3" is the JTAG chain configuration.
Change the mask to "7" to allow systems with a different chain
configuration to boot correctly.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Acked-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Added efuse status register base address. This register
is used for determining whether efuse was blown or not.
Also, added the zynq_get_silicon_version() to get the
silicon version of the zynq board.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The HW-defined procedure for booting Tegra requires that
CLAMP_INPUTS_WHEN_TRISTATED be enabled before programming the pinmux.
Add a function to the pinmux driver to allow boards to do this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The HW-defined procedure for booting Tegra requires that some pins be
set up as GPIOs immediately at boot in order to avoid glitches on those
pins, when the pinmux is programmed. Add a feature to the GPIO driver
which executes a GPIO configuration table. Board files will use this to
implement the correct HW initialization procedure.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Define enum PMUX_FUNC_DEFAULT, which indicates that a table entry passed
to pinmux_config_pingrp()/pinmux_config_pingrp_table() shouldn't change
the mux option in HW.
For pins that will be used as GPIOs, the mux option is irrelevant, so we
simply don't want to define any mux option in the pinmux initialization
table.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
If CONFIG_API is ever to be enabled on Tegra, this define must be set,
since api/api_storage.c uses it.
A couple of annoyting things about CONFIG_SYS_MMC_MAX_DEVICE
1) It isn't documented in README. The same is true for a lot of similar
defines used by api_storage.c.
2) It doesn't represent MAX_DEVICE but rather NUM_DEVICES, since the
valid values are 0..n-1 not 0..n.
However, I this patch does not address those shortcomings.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This patch includes following changes :
* Adds gpio pin numbering support for EXYNOS SOCs.
To have consistent 0..n-1 GPIO numbering the banks are divided
into different parts where ever they have holes in them.
* Rename GPIO definitions from GPIO_... to S5P_GPIO_...
These changes were done to enable cmd_gpio for EXYNOS and
cmd_gpio has GPIO_INPUT same as s5p_gpio driver and hence
getting a error during compilation.
* Adds support for name to gpio conversion in s5p_gpio to enable
gpio command EXYNOS SoCs. Function has been added to asm/gpio.h
to decode the input gpio name to gpio number.
Example: SMDK5420 # gpio set gpa00
Signed-off-by: Leela Krishna Amudala <l.krishna@samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Some platforms (tested on mpc85xx, mpc86xx) use global data before calling
function baord_inti_f(). The data should not be cleared later. Any arch
which uses global data in generic board board_init_f() should define
CONFIG_SYS_GENERIC_GLOBAL_DATA.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Scott Wood <scottwood@freescale.com>
CC: Simon Glass <sjg@chromium.org>
CC: Albert ARIBAUD <albert.u.boot@aribaud.net>
Acked-by: Simon Glass <sjg@chromium.org>
gd->bd->bi_baudrate is a copy of gd->baudrate.
Since baudrate is a common feature for all architectures,
keep gd->baudrate only.
It is true that bi_baudrate was passed to the kernel in that structure
but it was a long time ago.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Acked-by: Michal Simek <monstr@monstr.eu> (For microblaze)
On mx6sl there is a LVE (Low Voltage Enable) bit in the IOMUXC_SW_PAD_CTL
register that can enable or disable low voltage on the pad.
LVE is bit 22 of IOMUXC_SW_PAD_CTL register, but in order to make the
calculation easier we can define it as a flag in bit 1, since this bit is unused.
Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Otavio Salvador <otavio@ossystems.com.br>
The rmobile SoC has usb host controller.
This supports USB controllers listed in the R8A7790, R8A7791 and R8A7740.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Reviewed-by: Marek Vasut <marex@denx.de>
mx6slevk has a m25p32 SPI NOR flash connected to ESCSPI port.
Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
There is ES2 is a new revision to R8A7791.
This adds support this revision.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
There is ES2 is a new revision to R8A7790.
This adds support this revision.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
These functions are defined but has no prototype declaration. Add them.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Header files of R8A7790 and R8A7791 have common part of many.
This coordinates as rcar-base.h.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Make funtions static which are locally used in file
and remove the declaration from header file.
Signed-off-by: Manish Badarkhe <badarkhe.manish@gmail.com>
Ethernet driver configures the CPSW, SGMI and Phy and uses
the the Navigator APIs. The driver supports 4 Ethernet ports and
can work with only one port at a time.
Port configurations are defined in board.c.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Multicore navigator consists of Network Coprocessor (NetCP) and
Queue Manager sub system. More details on the hardware can
be obtained from the following links:-
Network Coprocessor: http://www.ti.com/lit/pdf/sprugz6
Multicore Navigator: http://www.ti.com/lit/pdf/sprugr9
Multicore navigator driver implements APIs to configure
the Queue Manager and NetCP Pkt DMA.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Acked-by: Tom Rini <trini@ti.com>
k2hk EVM is based on Texas Instruments Keystone2 Hawking/Kepler
SoC. Keystone2 SoC has ARM v7 Cortex-A15 MPCore processor. Please
refer the ti/k2hk_evm/README for details on the board, build and other
information.
This patch add support for keystone architecture and k2hk evm.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Sandeep Nair <sandeep_n@ti.com>
This patch moves the davinci i2c_defs.h file to drivers.i2c directory.
It will allow to reuse the davinci_i2c driver for TI Keystone2 SOCs.
Not used "git mv" command to move the file because small part of
it with definitions specific for Davinci SOCs has to remain in the
arch/arm/include/asm/arch-davinci.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Tom Rini <trini@ti.com>
Similar to OMAP5uEVM, PandaBoard, BeagleBoard-XM has a USB based
ethernet without MAC address embedded. So fake a MAC address following
the similar strategy used on OMAP5 and PandaBoard family.
Signed-off-by: Nishanth Menon <nm@ti.com>
introduce get_die_id() function which allows generation of
information such as fake MAC address from the processor ID code.
Signed-off-by: Nishanth Menon <nm@ti.com>
TI platforms such as OMAP5uevm, PandaBoard, use equivalent
logic to generate fake USB MAC address from device unique DIE ID.
Consolidate this to a generic location such that other TI platforms such
as BeagleBoard-XM can also use the same.
NOTE: at this point in time, I dont yet see a need for a generic dummy
ethernet MAC address creation function, but if there is a need in the
future, this can be further abstracted out.
Signed-off-by: Nishanth Menon <nm@ti.com>
The only remaining user of the custom bit manipulation function sr32()
is arch/arm/cpu/armv7/omap3/clock.c, so make it a static function in
that file to prepare complete removal.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Use smaller fields in the Tegra pinmux structures in order to pack the
data tables into a smaller space. This saves around 1-3KB for the SPL
and around 3-8KB for the main build of U-Boot, depending on the board,
which SoC it uses, and how many pinmux table entries there are.
In order to pack PMUX_FUNC_* into a smaller space, don't hard-code the
values of PMUX_FUNC_RSVD* to values which require 16 bits to store them,
but instead let their values be assigned automatically, so they end up
fitting into 8 bits.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Combine the Tegra USB header file into one header file for all SoCs.
Use ifdef to account for the difference, especially Tegra20 is quite
different from newer SoCs. This avoids duplication, mainly for
Tegra30 and newer devices.
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Tom Warren <twarren@nvidia.com>
On Tegra30 and later, the PTS (parallel transceiver select) and STS
(serial transceiver select) are part of the HOSTPC1_DEVLC_0 register
rather than PORTSC1_0 register. Since the reset configuration
usually matches the intended configuration, this error did not show
up on Tegra30 devices.
Also use the slightly different bit fields of first USB, (USBD) on
Tegra20 and move those definitions to the Tegra20 specific header
file.
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This renames all the pinmux pins, drive groups, and functions so they
have a prefix which matches the type name. These lists are also auto-
generated using scripts that were also used to generate the kernel
pinctrl drivers. This ensures that the lists are consistent between the
two.
The entries in tegra124_pingroups[] are all updated to remove the columns
which are no longer used.
All affected code is updated to match.
There are differences in the set of drive groups. I have validated this
against the TRM. There are differences order of pin definitions in
pinmux.c; these previously had significant mismatches with the correct
order:-( I adjusted a few entries in pinmux-config-venice2.h since the
set of legal functions for some pins was updated to match the TRM.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This renames all the pinmux pins, drive groups, and functions so they
have a prefix which matches the type name. These lists are also auto-
generated using scripts that were also used to generate the kernel
pinctrl drivers. This ensures that the lists are consistent between the
two.
The entries in tegra114_pingroups[] are all updated to remove the columns
which are no longer used.
All affected code is updated to match.
This introduces a few changes to pin/group/function naming and the set of
available functions for each pin. The new values now exactly match the
TRM; the chip documentation. I adjusted a few entries in
pinmux-config-dalmore.h due to this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This renames all the pinmux pins, drive groups, and functions so they
have a prefix which matches the type name. These lists are also auto-
generated using scripts that were also used to generate the kernel
pinctrl drivers. This ensures that the lists are consistent between the
two.
The entries in tegra30_pingroups[] are all updated to remove the columns
which are no longer used.
All affected code is updated to match.
This introduces a few changes to pin/group/function naming and the set of
available functions for each pin. The new values now exactly match the
TRM; the chip documentation. I adjusted one entry in
pinmux-config-cardhu.h due to this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This renames all the Tegra20 pinmux pins and functions so they have a
prefix which matches the type name.
The entries in tegra20_pingroups[] are all updated to remove the columns
which are no longer used.
All affected code is updated to match.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Clean up the naming of pinmux-related objects:
* Refer to drive groups rather than pad groups to match the Linux kernel.
* Ensure all pinmux API types are prefixed with pmux_, values (defines)
are prefixed with PMUX_, and functions prefixed with pinmux_.
* Modify a few type names to make their content clearer.
* Minimal changes to SoC-specific .h/.c files are made so the code still
compiles. A separate per-SoC change will be made immediately following,
in order to keep individual patch size down.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Remove a few unused functions from the pinmux header. They aren't
currently used, and removing them prevents any new usage from appearing.
This will ease moving to just pinmux_config_table() and
padgrp_config_table() in the future.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Much of arch/arm/cpu/tegra*-common/pinmux.c is identical. Remove the
duplication by creating pinmux-common.c for all the identical code.
This leaves:
* arch/arm/include/asm/arch-tegra*/pinmux.h defining only the names of
the various pins/pin groups, drive groups, and mux functions.
* arch/arm/cpu/tegra*-common/pinmux.c containing only the lookup table
stating which pin groups support which mux functions.
The code in pinmux-common.c is semantically identical to that in the
various original pinmux.c, but had some consistency and cleanup fixes
applied during migration.
I removed the definition of struct pmux_tri_ctlr, since this is different
between SoCs (especially Tegra20 vs all others), and it's much simpler to
deal with this via the new REG/MUX_REG/... defines. spl.c, warmboot.c,
and warmboot_avp.c needed updates due to this, since they previously
hijacked this struct to encode the location of some non-pinmux registers.
Now, that code simply calculates these register addresses directly using
simple and obvious math. I like this method better irrespective of the
pinmux code cleanup anyway.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Tegra's "APB misc" register region contains various miscellaneous
registers and the Tegra pinmux registers. Some code that touches the
misc registers currently uses struct pmux_tri_ctlr, which is intended to
be a definition of pinmux registers, rather than struct apb_misc_pp_ctrl,
which is intended to be a definition of the miscellaneous registers.
Convert all such code to use struct apb_misc_pp_ctrl, since struct
pmux_tri_ctlr goes away in the next patch.
This requires adding a missing field definition to struct
apb_misc_pp_ctrl, and moving the header into a more common location.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
pinmux_init() is a board-level function, not a pinmux driver function.
Move the prototype to a board header rather than the driver header.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
For consistency with other SoCs, modify Tegra20's enum pmux_func to:
* Remove PMUX_FUNC values that aren't real
* Use the same PMUX_FUNC_RSVD[1-4] values, and ensure (RSVD1 & 3)==0;
this will be assumed by pinmux_set_func() in a future patch.
Unfortunately, PMUX_FUNC_RSVD is still used in the pin macros. Use a
private define inside the driver to prevent this from causing compilaton
errors. This will be cleaned up when the pin tables are re-written in a
later patch in this series.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This field isn't used anywhere, so remove it. Note that PIN() macros are
left unchanged for now, to avoid many diffs to them; later commits will
completely rewrite them just one time.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This field isn't used anywhere, so remove it. Note that PIN() macros are
left unchanged for now, to avoid many diffs to them; later commits will
completely rewrite them just one time.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
this function is used by several board together with board_video_skip
to detect if hdmi is plugged is order to select the display to use.
So move it in imx-common to share it.
Signed-off-by: Eric Bénard <eric@eukrea.com>
this function is shared by several boards and thus can be factorized
Signed-off-by: Eric Bénard <eric@eukrea.com>
Acked-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Stefano Babic <sbabic@denx.de>
This patch add gicv3 support to uboot armv8 platform.
Changes for v2:
- rename arm/cpu/armv8/gic.S with arm/lib/gic_64.S
- move smp_kick_all_cpus() from gic.S to start.S, it would be
implementation dependent.
- Each core initialize it's own ReDistributor instead of master
initializeing all ReDistributors. This is advised by arnab.basu
<arnab.basu@freescale.com>.
Signed-off-by: David Feng <fenghua@phytium.com.cn>
This patch contains several changes required for second Ethernet
(enet1/RMII1) port on vf610
- ANADIG PLL5 control definitions required for Ethernet RMII1 clock
- Secondary Ethernet (enet1) MAC RMII1 base address definition
- RMII1 iomux definitions
- VF610_PAD_PTA6__RMII0_CLKOUT iomux definition required for
internal (e.g. crystal-less) Ethernet clocking.
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
[stefan@agner.ch: regrouped patch]
Signed-off-by: Stefan Agner <stefan@agner.ch>
The anadig_reg structure started at the wrong offset (fixed by adding
reserved_0x000[4]), was missing some reserved field required for
alignment purpose (reserved_0x094[3] between pll4_denom and pll6_ctrl)
and further contained a too short reserved field causing further miss-
alignment (reserved_0x0C4[7]). Also, rename all the reserved fields
and using a memory offset based scheme for.
Discovered and tested by temporarily putting the following debug
instrumentation into board_init():
struct anadig_reg *anadig = (struct anadig_reg *)ANADIG_BASE_ADDR;
printf("&anadig->pll3_ctrl=0x%p\n", &anadig->pll3_ctrl);
printf("&anadig->pll5_ctrl=0x%p\n", &anadig->pll5_ctrl);
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
[stefan@agner.ch: regrouped patch]
Signed-off-by: Stefan Agner <stefan@agner.ch>
When SoC first boots up, we should invalidate the cache but not flush it.
We can use the same function for invalid and flush mostly, with a wrapper.
Invalidating large cache can ben slow on emulator, so we postpone doing
so until I-cache is enabled, and before enabling D-cache.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: David Feng <fenghua@phytium.com.cn>
Clock Manager driver will be called to reconfigure all the
clocks setting based on user input. The input are passed to
Preloader through handoff files
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
CC: Pavel Machek <pavel@denx.de>
Cc: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Pavel Machek <pavel@denx.de>
Fix the macros guarding the spl.h header for various platforms. Due to
a typo and a propagation of it, the macros went out-of-sync with their
ifdef check, so fix this.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
The way that struct mmc was implemented was a bit of a mess;
configuration and internal state all jumbled up in a single structure.
On top of that the way initialization is done with mmc_register leads
to a lot of duplicated code in drivers.
Typically the initialization got something like this in every driver.
struct mmc *mmc = malloc(sizeof(struct mmc));
memset(mmc, 0, sizeof(struct mmc);
/* fill in fields of mmc struct */
/* store private data pointer */
mmc_register(mmc);
By using the new mmc_create call one just passes an mmc config struct
and an optional private data pointer like this:
struct mmc = mmc_create(&cfg, priv);
All in tree drivers have been updated to the new form, and expect
mmc_register to go away before long.
Changes since v1:
* Use calloc instead of manually calling memset.
* Mark mmc_register as deprecated.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Pull out "$(SRCTREE)/" from CONFIG_SYS_KWD_CONFIG
and push it into the top Makefile.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Michael Walle <michael@walle.cc>
Cc: Simon Guinot <simon.guinot@sequanux.org>
Cc: Dave Purdy <david.c.purdy@gmail.com>
Cc: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
Cc: Luka Perkov <luka@openwrt.org>
Cc: Valentin Longchamp <valentin.longchamp@keymile.com>
Cc: Jason Cooper <u-boot@lakedaemon.net>
Cc: Siddarth Gore <gores@marvell.com>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Eric Cooper <ecc@cmu.edu>
Cc: Suriyan Ramasami <suriyan.r@gmail.com>
This patch adds common dtsi file and config header for all
Exynos 4 based boards.
Patch additionaly adds board specific (weak) functions for
board_early_init_f and board_power_init functions.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch enables support for device tree for sdhci driver.
Non DT case is still supported.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch enables parsing mipi data from device tree.
Non device tree case is still supported.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add NAND SPL boot support with hardware PMECC.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Add SPI SPL boot support for sama5d3xek board.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Tegra124 moved the CSITE block's base address. Fix U-Boot to use
the correct address.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Register pmc_pwrgate_timer_mult has a different layout on Tegra114 and
Tegra124. Reflect this in pmc.h.
Also, simply write the whole of the register in start_cpu() rather than
doing a read-modify-write; the register is simple enough that the code
can easily construct the entire desired value.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
<asm/arch-tegra/tegra.h> needs to use CONFIG_TEGRA* to conditionalize
some definitions, since some modules moved between generations. Move
the definition of CONFIG_TEGRAnn to a header that's included earlier,
so that it's set by the time tegra.h needs to use it.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
omap_elm.h is a generic header used by OMAP ELM driver for all TI platfoms.
Hence this file should be present in generic folder instead of architecture
specific include folder.
Build tested using: ./MAKEALL -s am33xx -s omap3 -s omap4 -s omap5
Signed-off-by: Pekon Gupta <pekon@ti.com>
omap_gpmc.h is a generic header used by OMAP NAND driver for all TI platfoms.
Hence this file should be present in generic folder instead of architecture
specific include folder.
Build tested using: ./MAKEALL -s am33xx -s omap3 -s omap4 -s omap5
Signed-off-by: Pekon Gupta <pekon@ti.com>
Each SoC platform (AM33xx, OMAP3, OMAP4, OMAP5) has its own copy of GPMC related
defines and declarations scattered in SoC platform specific header files
like include/asm/arch-xx/cpu.h
However, GPMC hardware remains same across all platforms thus this patch merges
GPMC data scattered across different arch-xx specific header files into single
header file include/asm/arch/omap_gpmc.h
Build tested using: ./MAKEALL -s am33xx -s omap3 -s omap4 -s omap5
Signed-off-by: Pekon Gupta <pekon@ti.com>
OMAP NAND driver can detect Page-size and OOB-size of NAND device from ONFI
params or nand_id[] table. And based on that it defines ECC layout.
This patch
1) removes following board configs used for defining NAND ECC layout
- GPMC_NAND_ECC_LP_x16_LAYOUT (for large page x16 NAND)
- GPMC_NAND_ECC_LP_x8_LAYOUT (for large page x8 NAND)
- GPMC_NAND_ECC_SP_x16_LAYOUT (for small page x16 NAND)
- GPMC_NAND_ECC_SP_x8_LAYOUT (for small page x8 NAND)
2) removes unused #defines in common omap_gpmc.h depending on above configs
Build tested using: ./MAKEALL -s am33xx -s omap3 -s omap4 -s omap5
Signed-off-by: Pekon Gupta <pekon@ti.com>
Currently there are two sets of omap_gpmc.h header files
(a) arch/arm/include/asm/omap_gpmc.h
common header file for all platforms, containing defines and declarations used
by GPMC NAND driver.
(b) arch/arm/include/asm/arch-xx/omap_gpmc.h
SoC platform specific header file containing defines like ECC layout.
This patch removes platform specific arch-xx/omap_gpmc.c because:
- GPMC hardware engine is common for all SoC platforms hence only (a) is enough
- ECC layout is now defined in omap_nand.c driver itself based on ecc-scheme
selected. Hence all ECC layout declarations in (b) are redundant.
Build tested using: ./MAKEALL -s am33xx -s omap3 -s omap4 -s omap5
Signed-off-by: Pekon Gupta <pekon@ti.com>
Copied from Linux sources "include/linux/sizes.h" commit
413541dd66d51f791a0b169d9b9014e4f56be13c
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Tom Rini <trini@ti.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Acked-by: Tom Rini <trini@ti.com>
Acked-by: Stefan Roese <sr@denx.de>
[trini: Add bcm Kona platforms to the patch]
Signed-off-by: Tom Rini <trini@ti.com>
chip->ecc.hwctl() is used for preparing the H/W controller before read/write
NAND accesses (like assigning data-buf, enabling ECC scheme configs, etc.)
Though all ECC schemes in OMAP NAND driver use GPMC controller for generating
ECC syndrome (for both Read/Write accesses). But but in current code
HAM1_ECC and BCHx_ECC schemes implement individual function to achieve this.
This patch
(1) removes omap_hwecc_init() and omap_hwecc_init_bch()
as chip->ecc.hwctl will re-initializeGPMC before every read/write call.
omap_hwecc_init_bch() -> omap_enable_ecc_bch()
(2) merges the GPMC configuration code for all ECC schemes into
single omap_enable_hwecc(), thus adding scalability for future ECC schemes.
omap_enable_hwecc() + omap_enable_ecc_bch() -> omap_enable_hwecc()
Signed-off-by: Pekon Gupta <pekon@ti.com>
Add bcm281xx architecture support code including a clock framework and
chip reset. Define register block base addresses for the bcm281xx
architecture and create an empty gpio header file required when
CONFIG_CMD_GPIO is set.
Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Reviewed-by: Steve Rae <srae@broadcom.com>
Reviewed-by: Tim Kryger <tkryger@linaro.org>
The Kona architecture is present on a number of Broadcom mobile SoCs
including the bcm281xx family of chips.
Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Reviewed-by: Steve Rae <srae@broadcom.com>
Reviewed-by: Tim Kryger <tkryger@linaro.org>
Schematic indicates GPIO5_7 is to be used for VTT regulator control
rather than GPIO0_21 so modify enable_vtt_regulator to reflect this.
Without this some boards will experience DDR3 corruption and fail to
boot.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
[trini: Rework patch against mainline]
Signed-off-by: Tom Rini <trini@ti.com>
Adds support for Bernecker & Rainer Industrieelektronik GmbH KWB
Motherboard, using TI's AM3352 SoC.
Most of code is derived from TI's AM335x_EVM
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
Cc: trini@ti.com
This patch add support for the Silica Pengwyn board [1]
The board is based on a TI AM3354 CPU [2]
All jumpers removed it will boot from the SDcard, the console is on
UART1 accessible via the FDTI -> USB. The on board NAND flash is
supported and can act as boot medium, depending on jumper settings.
USB Host, USB Device and Ethernet are also provided but untested.
[1]
http://www.silica.com/product/silica-pengwyn-board.html
[2]
http://www.ti.com/product/am3354
Signed-off-by: Lothar Felten <lothar.felten@gmail.com>
[trini: Move CONFIG_BOARD_LATE_INIT into am335x_evm.h, drop unused
spi0_pin_mux from Pengwyn support]
Signed-off-by: Tom Rini <trini@ti.com>
Conflicts:
Makefile
drivers/net/npe/Makefile
These two conflicts arise from commit 0b2d3f20
("ARM: NET: Remove the IXP NPE ethernet driver") and are
resolved by deleting the drivers/net/npe/Makefile file
and removing the CONFIG_IXP4XX_NPE line from Makefile.
Having CONFIG_SYS_I2C_BASE requires DW I2C driver to explicitly include
<arch/hardware.h> which other platforms may not have at all.
It's always good to have a driver platform-independent.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Tom Rini <trini@ti.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Vipin Kumar <vipin.kumar@st.com>
Cc: Armando Visconti <armando.visconti@st.com>
- When CONFIG_DISPLAY_CPUINFO is not enabled,
print_cpuinfo() should be defined as an empty function
in a header, include/common.h
- Remove #ifdef CONFIG_DISPLAY_CPUINFO .. #endif
from caller, common/board_f.c and arch/arm/lib/board.c
- Remove redundant prototypes in arch/arm/lib/board.c,
arch/arm/include/asm/arch-am33x/sys_proto.h and
board/nokia/rx51/rx51.h, keeping the one in include/common.h
- Add #ifdef CONFIG_DISPLAY_CPUINFO to the func definition
where it is missing
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Add the SATA boot support for OMAP5 and dra7xx.
Renamed the omap_sata_init to the common init_sata(int dev)
for commonality in with sata stack.
Added the ROM boot device ID for SATA.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
SPL is using ps7_init.c/h files which are generated
from design tools which have to be copied to
boards/xilinx/zynq folder before compilation.
BSS section is moved to SDRAM because fat support
requires more space than SRAM size.
Added:
- MMC and QSPI support
- Boot OS directly from SPL
- Enable SPL command
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
Remove hard coded clock divider setting and use the Zynq clock framework
to dynamically calculate appropriate dividers at run time.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The GEM driver should not need to know about Zynq specific details of
RCLK related registers and bitfields in the SLCR. Move those details to
the slcr driver.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Define both serial uarts in the driver and return
default uart based on board configuration.
- Move baseaddresses to hardware.h
- Define default baudrate and clock values
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The dual lite and solo variant have only 4 SPI controller.
respect this in the MXC_SPI_BASE_ADRESSES macro
Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Provide define for the SCLK_CTL field of the config reg of ECSPI.
While at it, oder the defines to improve readability and make
adding more defines easier.
Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Currently when we boot a mx6dual U-boot reports that it is a mx6quad.
Report it as MX6D instead:
CPU: Freescale i.MX6D rev1.2 at 792 MHz
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano babic <sbabic@denx.de>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Instead of duplicating the CPU definitions at mx5 and mx6 sys_proto.h header
files, introduce a common header to centralize such definitions.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
This patch corrects the divider value written to CLKDIV register.
Since SDCLKIN is divided inside controller by the DIVRATIO value set
in the CLKSEL register, we need to use the same output clock value to
calculate the CLKDIV value.
as per user manual: cclk_in = SDCLKIN / (DIVRATIO + 1)
Input parameter to mmc_clk is changed to dwmci_host, since
we need the same to read DWMCI_CLKSEL register.
This improves the read timing values for channel 0 on SMDK5250
from 0.288sec to 0.144sec
Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
This patch adds s5p_cpu_rev.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch enables to read cpu revision on Exynos CPU.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The architecture is unmaintained and dead, remove it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Michael Schwingen <michael@schwingen.org>
Cc: Tom Rini <trini@ti.com>
These headers define the Tegra124 hardware. Add them to the usual
place.
Add Tegra124 chip ID/SKU ID definitions to common headers.
There's no real HW change on Tegra124 for 90% of the toys, so it might
make sense for a future patch to unify some of the content of these
files in a common location.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Pass just the partition ID to power_partition(), rather than also passing
the partition's status register mask too. This makes it simpler to get
call-sites correct, since they don't need to pass two different values
that define the same thing and must match.
Consequently, we can remove the mask definitions from pmc.h.
Suggested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Use a named constant for the PLL lock bit in enable_cpu_clocks().
Construct the complete value of pmc_pwrgate_toggle, rather than doing a
read-modify-write; the register is simple enough and doesn't need to
maintain state between operations.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Based on the Tegra TRM, the system clock (which is the AVP clock) can
run up to 275MHz. On power on, the default sytem clock source is set to
PLLP_OUT0. In function clock_early_init(), PLLP_OUT0 will be set to
408MHz which is beyond system clock's upper limit.
The fix is to set the system clock to CLK_M before initializing PLLP,
and then switch back to PLLP_OUT4, which has an appropriate divider
configured, after PLLP has been configured
Implement this logic in new function tegra30_set_up_pllp(),
which sets up PLLP and all PLLP_OUT* dividers, and handles the AVP
clock switching. Remove the duplicate PLLP setup from pllx_set_rate()
and adjust_pllp_out_freqs().
Signed-off-by: Jimmy Zhang <jimmzhang@nvidia.com>
[swarren, significantly refactored the change]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Tegra114 and later's PMC module removes the pwrgate_timer_on register
and replaces it with a clamp_status register. Adjust pmc.h to reflect
this, and update any code affected by the change.
The cpu.c change in this patch was extracted from a much larger patch
by Jimmy Zhang. The pmc.h change was written from scratch, but inspired
by related changes made by Tom Warren.
There could well be other differences in the PMC register set for chips
after Tegra20/30. However, they don't affect the code in U-Boot at
present, so I haven't attempted an exhaustive update of pmc.h.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Some clock sources have 3-bit muxes in bits 31:29. Implement core
support for this mux field.
Signed-off-by: Tom Warren <twarren@nvidia.com>
[swarren, extracted from a larger patch by Tom]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Since all code that sets or interprets MASK_BITS_* now uses the enums
to define/compare the values, there is no need for MASK_BITS_* to have
a specific integer value. In fact, having a specific integer value may
encourage people to hard-code those values, or interpret the values in
incorrect ways.
As such, remove the logic that assigns a specific value to the enum
values in order to make it completely clear that it's just an enum, not
something that directly represents some integer value.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
OUT_CLK_SOURCE_ are currently named after the number of bits the mask
they represent includes. However, bit count is not the only possible
variable; bit position may also vary. Rename OUT_CLK_SOURCE_ to
OUT_CLK_SOURCE_31_30_ and OUT_CLK_SOURCE4_ to OUT_CLK_SOURCE_31_28 to
more completely describe exactly what they represent, without having to
go look up the definitions.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The only place where the MASK_BITS_* values are used is in
adjust_periph_pll(), which interprets the value 4 (old MASK_BITS_29_28,
new MASK_BITS_31_28) as being associated with mask OUT_CLK_SOURCE4_MASK,
i.e. bits 31:28. Rename the MASK_BITS_ macro to reflect how it's actually
implemented.
Note that no Tegra clock register actually uses all of bits 31:28 as
the mux field. Rather, bits 30:28, 29:28, or 28 are used. However, in
those cases, nothing is stored in the bits above the mux field, so it's
safe to pretend that the mux field extends all the way to the end of the
register. As such, the U-Boot clock driver is currently a bit lazy, and
doesn't distinguish between 31:28, 30:28, 29:28 and 28; it just lumps
them all together and pretends they're all 31:28. This patch doesn't
cause this issue; it was pre-existing. Hopefully, future patches will
clean this up.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The enum used to define the set of register bits used to represent a
clock's input mux, MUX_BITS_*, is defined separately for each SoC at
present. Move this definition to a common location to ease fixing up
some issues with the definition, and the code that uses it.
Signed-off-by: Tom Warren <twarren@nvidia.com>
[swarren, extracted from a larger patch by Tom]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Old s5p gpio coding method was not clean and was not working properly
for all parts and banks. New method is clean and easy to extend.
Gpio coding mask:
0x000000ff - pin number
0x00ffff00 - bank offset
0xff000000 - part number
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add PCIe driver for the Freescale i.MX6 SoC . This driver operates the
PCIe block in RC mode only, the EP mode is NOT supported. The driver is
tested with the Intel e1000 NIC driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Split the SATA clock enabling function and add PCI express clock
enabling function. The SATA clock enabling function starts up the
100MHz SATA reference PLL in ENET_PLL register, but the code can
be re-used to enable the 125MHz PCIe reference in ENET_PLL, so pull
this code into separate function. Moreover, add the PCIe clock
enabling code.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Add SPL support to be able to detect a USB Mass Storage device
connected to a USB host. Once a USB Mass storage device is detected
the SPL will load the u-boot.img from a FAT partition to target address.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Patch adds modification to shared omap5 abb_setup() function, and
proper registers definitions needed for ABB setup sequence. ABB is
initialized for MPU voltage domain at OPP_NOM.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
ES1.1 silicon is a very minor variant of ES1.0. Add priliminary support
for ES1.1 IDCODE change.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
This patch enables dynamically powering down the
IO receiver when not performing a read on boards using DDR3.
This optimizes both active and standby power consumption.
This bit is not set on EVM SK and EVM 1.5 and later boards.
Setting the same.
This has been tested on PG2.0 EVM1.5, EVM1.2, EVM-SK, BBB.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Satyanarayana, Sandhya <sandhya.satyanarayana@ti.com>
Other TI processors like am33xx, omap4 and omap5 have called these variables
as NON_SECURE_SRAM_*, shouldn't be a big problem rename these variables to
be coherent.
One reason more to rename these variables is to have the possibility of any
OMAP3 board to use the ti_armv7_common.h include as the NON_SECURE_SRAM_END
is used to define the CONFIG_SYS_INIT_SP_ADDR variable.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
The commit
f3f98bb0 : "ARM: OMAP4/5: Do not configure non essential pads, clocks, dplls"
removed the config option aimed towards moving that stuff into kernel, which
renders some code unreachable. Remove that code.
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
