Add basic support for rv1108 evb, whith this patch we
can boot into u-boot console.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
RV1108 is embedded with an ARM Cortex-A7 single core and a DSP core
from Rockchip. It is designed for varies application scenario such
as car DVR, sports DV, secure camera and UAV camera.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add config of max root ports and add config to enable xhci
controller.
Signed-off-by: Meng Dongyang <daniel.meng@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add defconfig for usb and ehci and ohci controller, config maximal
number of ports of the root hub for ohci driver.
Signed-off-by: Meng Dongyang <daniel.meng@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
PX5 EVB is designed by Rockchip for automotive field
with integrated CVBS (TP2825) / MIPI DSI / CSI / LVDS
HDMI video input/output interface, audio codec ES8396,
WIFI / BT (on RTL8723BS), Gsensor BMA250E and light&proximity
sensor STK3410.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The GeekBox is a TV box from GeekBuying, based on an MXM3 module.
The module can be used with base boards such as the GeekBox Landingship.
This adds basic support to chain-load U-Boot from Rockchip's miniloader.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Sheep board is designed by Rockchip as a EVB for rk3368.
Currently it is able to boot a linux kernel and system
to console with the miniloader run as fist level loader.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
The RK3368 is an octa-core Cortex-A53 SoC from Rockchip.
This adds basic support to chain-load U-Boot from Rockchip's
miniloader.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With our efuse driver for the RK3399 ready, we can add the
board-specific code that consumes the cpuid from the efuse block and
postprocesses it into the system serial (using the same CRC32 based
derivation as in Linux).
We expose the cpuid via two distinct environment variables:
serial# - the serial number, as derived in Linux
cpuid# - the raw 16 byte CPU id field from the fuse block
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
The problems with the current DFU layout are:
MMC: The space allocated for u-boot is too small for the latest u-boot
(>750KB). We need to increase it. eMMC uses a much bigger area (2MB).
eMMC: region "u-boot.img.raw" overlaps the environment area and the region
"spl-os-image.raw".
both: region "spl-os-image.raw" is quite small and can't handle android
kernels
Fixing this requires growing some regions and moving others.
Care has been taken to leave some room for further growth of
"spl-os-args.raw".
Also the "env" now appears in the dfu so that it's apparent that the
region is not free space that can be used to grow "u-boot.img.raw".
The MLO region is 0x100 sectors wide but the 0x100 are unused in case the
MLO comes too overflow this areas.
The total space allocated for those raw binaries is 16MB, of which 13+MB
are reserved for the kernel image.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
At present bootstage only supports U-Boot proper. But SPL can also consume
boot time so it is useful to have the record start there.
Add bootstage support to SPL. Also support stashing the timing information
when SPL finishes so that it can be picked up and reported by U-Boot
proper. This provides a full boot time record, excluding only the time
taken by the boot ROM.
Signed-off-by: Simon Glass <sjg@chromium.org>
There are a few places that should use const *, such as
bootstage_unstash(). Update these to make it clearer when parameters are
changed.
Signed-off-by: Simon Glass <sjg@chromium.org>
We should return a proper error number instead of just -1. This helps the
caller to determine what when wrong. Update a few functions to fix this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some boards cannot access pre-relocation data after relocation. Reserve
space for this and copy it during preparation for relocation.
Signed-off-by: Simon Glass <sjg@chromium.org>
There are several code style and comment nits. Fix them and also remove
the comment about passing bootstage to the kernel being TBD. This is
already supported.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present bootstage uses the data section of the image to store its
information. There are a few problems with this:
- It does not work on all boards (e.g. those which run from flash before
relocation)
- Allocated strings still point back to the pre-relocation data after
relocation
Now that U-Boot has a pre-relocation malloc() we can use this instead,
with a pointer to the data in global_data. Update bootstage to do this and
set up an init routine to allocate the memory.
Now that we have a real init function, we can drop the fake 'reset' record
and add a normal one instead.
Note that part of the problem with allocated strings remains. They are
reallocated but this will only work where pre-relocation memory is
accessible after relocation.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we provide a default version of this function for use by
bootstage. However it uses the system timer and therefore likely requires
driver model. This makes it impossible to time driver-model init.
Drop the function and require boards to provide their own. Add a sandbox
version also. There is a default implememtation in lib/time.c for boards
which use CONFIG_SYS_TIMER_COUNTER.
Signed-off-by: Simon Glass <sjg@chromium.org>
The SD card automatic installation system depends on the default
environment of the previous U-Boot.
Add the missing environment variables.
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
Supported boot devices are raw QSPI and raw SD card.
Add support for a FAT16/32 file system for SD card.
The SOC's boot ROM only supports FAT file system.
Therefore remove the SPL support for the EXT file system.
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
We should not have an arch-specific header file in common.h. Adjust the
board files a little so it is not needed, and drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
We should not have an arch-specific header file in common.h. Instead, use
the asm/hardware.h header to provide the required declarations, and drop
the common.h changes.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
These declarations should not be in common. Remove those that are not
needed and move the others to an arch-specific location.
Signed-off-by: Simon Glass <sjg@chromium.org>
The declarations should not be in common.h. Move them to the arch-specific
headers.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Fixup thinko defined(FSL_LSCH3) -> defined(CONFIG_FSL_LSCH3)]
Signed-off-by: Tom Rini <trini@konsulko.com>
Set up a new asm/ppc.h header file to hold this arch-specific stuff. It
should not be in common.h. It probably should be refactored to use
asm/arch instead, but that is a job for the maintainer.
Signed-off-by: Simon Glass <sjg@chromium.org>
With a small tweak we can avoid including these files for all boards.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This is not actually needed anywhere, so drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Rather than including this arch-specific header file in common.h, include
it from within nds32's u-boot.h header.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rather than including this arch-specific header file in common.h, include
it from within mips's u-boot.h header.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Rather than including this arch-specific header file in common.h, include
it from within arm's u-boot.h header.
Also drop the comment about something to be fixed. It has been there
forever and it is not clear what it means.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rather than including this arch-specific header file in common.h, include
it from within x86's u-boot.h header.
Also drop the comment about something to be fixed. It is not clear what
needs fixing.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rather than including this arch-specific header file in common.h, include
it from within sandbox's u-boot.h header.
Also drop the comment about something to be fixed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rather than including this arch-specific header file in common.h, include
it from within arc's u-boot.h header.
Signed-off-by: Simon Glass <sjg@chromium.org>
The symbol CONFIG_TI81XX is used for the parts that are common to the
TI816x and TI814x SoCs and are not part of CONFIG_ARCH_OMAP2PLUS nor
CONFIG_AM33XX. It however has so few uses that we can just modify the
code to check for both and drop the symbol. The symbols CONFIG_TI816X
and CONFIG_TI814X are for the repective SoCs.
Signed-off-by: Tom Rini <trini@konsulko.com>
- Switch to using <configs/ti_armv7_omap.h> and family. This lets us
drop lots of custom defines.
- Ensure that our default environment uses DEFAULT_LINUX_BOOT_ENV so
that Linux will boot correctly.
- Enable CONFIG_DISTRO_DEFAULTS
- Switch to using CONFIG_OF_CONTROL
- Various other cleanups to match other SoCs in the family line.
Signed-off-by: Tom Rini <trini@konsulko.com>
The ti816x/am389x SoC is the first generation in what U-Boot calls the
"am33xx" family. In the first generation of this family the DDR
initialization sequence is quite different from all of the subsequent
generations. Whereas with ti814x (second generation) we can easily work
the minor differenced between that and am33xx (third generation), our
attempts to do this for ti816x weren't sufficient. Rather than add a
large amount of #ifdef logic to make this different sequence work we add
a new file, ti816x_emif4.c to handle the various required undocumented
register writes and sequence and leverage what we can from
arch/arm/mach-omap2/am33xx/ddr.c still. As DDR2 has similar problems
today but I am unable to test it, we drop the DDR2 defines from the code
rather than imply that it works by leaving it. We also remove a bunch
of other untested code about changing the speed the DDR runs at.
Signed-off-by: Tom Rini <trini@konsulko.com>
Now that these symbols are in Kconfig, migrate all users. Use imply on
a number of platforms that default to having this enabled. As part of
this we must migrate some straglers for CMD_FAT and DOS_PARTITION.
Signed-off-by: Tom Rini <trini@konsulko.com>
Add fallbacks needed to keep all boards building
while they are migrated to use Kconfig symbols
instead of defines in <board>_config.h files for
FAT filesystem.
These should eventually go away once Kconfig select
or imply statements are put in place and duplicated
defines in <board>_config.h removed.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
[trini: Update logic since CMD_FAT / CONFIG_SPL_FAT_SUPPORT are
selecting FS_FAT]
Signed-off-by: Tom Rini <trini@konsulko.com>
Since config fallbacks contained in include/config_fallbacks.h
come into k2g_evm.h file through ti_armv7_keystone2.h, it should
be the last file included.
Without this, #define of FAT_WRITE when environment is in FAT
does not happen as the environment location is decided later
in the file.
Similar issues can come with other config fallbacks implemented.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Not all TI Keystone2 EVMs want environment in NAND flash.
K2G EVM which has an MMC/SD slot, keep environment in a
FAT partition on SD card.
Since ti_armv7_keystone2.h defines environment is in NAND,
boards which do not follow that have to #undef'ine that
configuration. This leads to ugly ordering issues around
where exactly the include of ti_armv7_keystone2.h can come
in within the k2*_evm.h files.
Move environment location to config file of each board.
This should make it easy to change it for any one board
without affecting all other boards.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
These header files are actually part of libfdt. Move them there to make
it easier to build pylibfdt and easier to merge changes from upstream.
Update the license header to use SPDX at the same time.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add CONFIG_NAND_BOOT config flag to organise
NAND_BOOT specific code in config flag like
-nand-boot specfic errata errata_rcw_src()
-CONFIG_SYS_NAND_U_BOOT_DST,etc
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Abhimanyu Saini <abhimanyu.saini@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
modify u_qe_init to upload QE firmware from SD card when it is SD
boot
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
DPAA2 platforms boot the Management Complex based on the u-boot env
variable "mcinitcmd". Instead of doing this step on each platform
individually, define a single mc_env_boot function in the MC driver,
since it's semantically tied to it.
Call the function in a per-board reset_phy hook, as it gets called at a
later moment, when all board PHY devices have been initialized.
Signed-off-by: Bogdan Purcareata <bogdan.purcareata@nxp.com>
Signed-off-by: Heinz Wrobel <heinz.wrobel@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Update the SPI uclass to support a live device tree. Also adjust
spi_slave_ofdata_to_platdata() to accept a device instead of a blob and
offset.
Signed-off-by: Simon Glass <sjg@chromium.org>
Update the xlate() method to use ofnode_phandle_args instead of the fdtdec
variant. This will allow drivers to support a live device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add an implementation of strcspn() which returns the number of initial
characters that do not match any in a rejection list.
Signed-off-by: Simon Glass <sjg@chromium.org>
This functions works like strchr() but returns the end of the string if
the character is not found. Add an implementation of this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add some definitions and helpers for livetree in the main of.h header
file. These include:
- reading multi-cell integers
- default number of address/size cells
- functions for comparing names
Signed-off-by: Simon Glass <sjg@chromium.org>
These two functions have an of_ prefix which conflicts with naming used
in of_addr. Rename them:
fdt_read_number
fdt_support_bus_default_count_cells
Signed-off-by: Simon Glass <sjg@chromium.org>
Convert this driver to support the live device tree and remove the old
fdtdec support.
The keyboard is not yet converted.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for requesting GPIOs with a live device tree.
This involves adjusting the function signature for the legacy function
gpio_request_by_name_nodev(), so fix up all callers.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes to stm32f746-disco.c:
Signed-off-by: Tom Rini <trini@konsulko.com>
Move the main part of the GPIO request function into a separate function
so that it can be used by the live tree function when added. Update the
xlate method to use a node reference.
Update all GPIO drivers to handle the modified xlate() method.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some tests require either livetree or flat tree. Add flags to allow the
tests to specify this. Adjust the test runner to run with livetree (if
supported) and then flat tree.
Some video tests are quite slow and running on flat tree adds little extra
test value, so run these on livetree only.
Signed-off-by: Simon Glass <sjg@chromium.org>
When starting up driver model with a live tree we need to scan the tree
for devices. Add code to handle this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Adjust this function to us an ofnode instead of an offset, so it can be
used with livetree. This involves updating all callers.
Signed-off-by: Simon Glass <sjg@chromium.org>
Adjust this function to use an ofnode instead of an offset, so it can be
used with livetree. This involves updating all callers.
Signed-off-by: Simon Glass <sjg@chromium.org>
When a live tree is being used we need to record the node that was used to
create the device. Update device_bind_with_driver_data() to support this.
Signed-off-by: Simon Glass <sjg@chromium.org>
When the live tree is supported some functions need to change a little.
Add an implementation which is used when not inlining these functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is common to read a device-tree property from the node associated with
a device. Add convenience functions to do this so that drivers do not need
to deal with accessing the ofnode from the device.
These functions all start with 'dev_read_' to provide consistent naming
for all functions which read information from a device's device tree node.
These are inlined when using the flat DT to save code size. The live tree
implementation is added in a later commit.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some functions deal with structured data rather than simple data types.
It makes sense to have these in their own file. For now this just has a
function to read a flashmap entry. Move the data types also.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add functions to access addresses in the device tree. These are brought
in from Linux 4.10.
Also fix up the header guard for fdtaddr.h to avoid confusion.
Signed-off-by: Simon Glass <sjg@chromium.org>
Since U-Boot supports both a live tree and a flat tree, we need an easy
way to access the tree without worrying about which is currently active.
To support this, U-Boot has the concept of an ofnode, which can refer
either to a live tree node or a flat tree node.
For the live tree, the reference contains a pointer to the node (struct
device_node *) or NULL if the node is invalid. For the flat tree, the
reference contains the node offset or -1 if the node is invalid.
Add a basic set of operations using ofnodes. These are implemented by
using either libfdt functions (in the case of a flat DT reference) or
the live-tree of_...() functions.
Note that it is not possible to have both live and flat references active
at the same time. As soon as the live tree is available, everything in
U-Boot should switch to using that. This avoids confusion and allows us to
assume that the type of a reference is simply based on whether we have a
live tree yet, or not.
Signed-off-by: Simon Glass <sjg@chromium.org>
The of_ prefix conflicts with the livetree version of this function.
Rename it to avoid problems when we add livetree support.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function converts the flat device tree into a hierarchical one with
C structures and pointers. This is easier to access.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a basic assortment of functions to access the live device tree. These
come from Linux v4.9 and are modified for U-Boot to the minimum extent
possible. While these functions are now very stable in Linux, it will be
possible to merge in fixes if needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a Kconfig option to enable a live device tree, built at run time from
the flat tree. Also add structure definitions and a root node.
Signed-off-by: Simon Glass <sjg@chromium.org>
In linux v4.9 this returns a value. This saves checking the warning
condition twice in some code.
Update the U-Boot version to do this also.
Signed-off-by: Simon Glass <sjg@chromium.org>
Sometimes it is useful to be able to find a block device without also
probing it. Add a function for this as well as the associated test.
Signed-off-by: Simon Glass <sjg@chromium.org>
With live tree we need a struct device_node * to reference a node. With
the existing flat tree, we need an int offset. We need to unify these into
a single value which can represent both.
Add an ofnode union for this and adjust existing code to move to this.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function is only used in one place. It is better to just declare it
internally since there is a simpler replacement for use outside the
driver-model core code.
Signed-off-by: Simon Glass <sjg@chromium.org>
These support the flat device tree. We want to use the dev_read_..()
prefix for functions that support both flat tree and live tree. So rename
the existing functions to avoid confusion.
In the end we will have:
1. dev_read_addr...() - works on devices, supports flat/live tree
2. devfdt_get_addr...() - current functions, flat tree only
3. of_get_address() etc. - new functions, live tree only
All drivers will be written to use 1. That function will in turn call
either 2 or 3 depending on whether the flat or live tree is in use.
Note this involves changing some dead code - the imx_lpi2c.c file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move this group of address-related functions into a new file. These use
the flat device tree. Future work will provide new versions of these which
can support the live tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
The Linux device tree for the Allwinner A64 SoC has changed a lot since
the U-Boot version was merged.
Let's replace the current DT with a exact copy of the Linux one as of:
commit c6778ff813d2ca3e3c8733c87dc8b6831a64578b
Merge: 0ff4c01 3c0e3abd
Author: Linus Torvalds <torvalds@linux-foundation.org>
Date: Tue May 9 10:07:33 2017 -0700
This is the DT used in Linux 4.12-rc1.
Since U-Boot has an Ethernet driver (while Linux does not yet), we
provide the required DT nodes for it in an ...-u-boot.dtsi file, to both
mark them as U-Boot specific and to allow easier upgrading once Linux gets
the driver and its own binding later.
Compared to the existing Ethernet DT nodes we just slightly tweak the clock
and reset nodes in there to match the new bindings used by Linux for those.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Currently these (board agnostic) commands cannot be selected using
menuconfig and friends. Fix this the obvious way. As part of this,
don't muddle the meaning of CONFIG_HASH_VERIFY to mean both 'hash -v'
and "we have a hashing command" as this makes the Kconfig logic odd.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
[trini: Re-apply, add imply for a few cases, run moveconfig.py, also
migrate CRC32_VERIFY]
Signed-off-by: Tom Rini <trini@konsulko.com>
Engicam has several SOM's on i.MX6 stream, where each SOM
has one include/configs/*.h file, this patch generate single
config file for all SOM's include/configs/imx6-engicam.h
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Define FDT_ADDR based on the respective SOM, and later patches
will make use of this fdt_addr in single config file.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
- IMX_FEC_BASE: icorem6 using dts, no need for explicit base.
- CONFIG_ETHPRIME: ethprime env not using anywhere in the board.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
The config variable CONFIG_SPL_NAND_MXS is only set in
include/configs/imx6_spl.h but used nowhere.
Remove it.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
There is no dedicated reset signal wired up for the MX6QDL thus if the
bootloader enables the link we need some special handling to get the core
back into a state where it is safe to touch it for configuration.
While there has been some special handling in the Linux kernel to do this,
it was removed in 4.11 thus we need to do it properly in the bootloader
and therefore without this if you enable PCI in the bootloader you will hang
while booting the 4.11 kernel.
This puts the PCIe controller back into a safe state for the kernel driver
before launching the kernel.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Peter Senna Tschudin <peter.senna@collabora.com>
After running 'saveenv' we can no longer boot.
Adjust CONFIG_ENV_OFFSET so that U-Boot binary and the environment
section do not overlap.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Add the initial support for pico-imx7d board based on Wig Cheng's
source code.
Add support for eMMC, USB gadget, I2C, PMIC and Ethernet.
For more information about this board, please visit:
http://www.technexion.org/products/pico/pico-som/pico-imx7-emmc
Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Switch Clearfog to the generic distro defaults. This has been taken
from a Debian mailing list thread:
https://lists.debian.org/debian-boot/2016/10/msg00026.html
Signed-off-by: Patrick Wildt <patrick@blueri.se>
Signed-off-by: Stefan Roese <sr@denx.de>
Currently while setting the vsel value for dcdc1 and dcdc2
the driver is wrongly masking the entire 8 bits in the process
clearing PFM (bit7) field as well. Hence describe an appropriate
mask for vsel field and modify only those bits in the vsel
mask.
Source: http://www.ti.com/lit/ds/symlink/tps65218.pdf
Signed-off-by: Keerthy <j-keerthy@ti.com>
Fixes: 86db550b38 ("power: Add support for the TPS65218 PMIC")
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
In some places we check if part_config is set to MMCPART_NOAVAILABLE
(0xff). With part_config being a char this is always false. We should
be using a u8 to store this value instead, after a quick consultation
with the Linux Kernel. Reported by clang-3.8.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This patch adjusts memory map for secure boot headers on LS2080AQDS
and LS2080ARDB platforms. Secure boot headers are placed on NOR
flash at offset 0x00600000.
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch is to adjust the memory mapping for FLash/SD card on
LS1046AQDS and LS1046ARDB, such as FMAN firmware load address, U-Boot
start address on serial flash and environment address.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch is to adjust the memory mapping for FLash/SD card on
LS1043AQDS and LS1043ARDB, such as PPA firmware load address, FMAN
firmware load address, QE firmware load address, U-Boot start address
on serial flash and environment address.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch is to adjust the memory mapping for FLash/SD card on
LS1021AQDS and LS1021ATWR, such as U-Boot start address on serial
Flash, QE firmware load address and environment address.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS2081ARDB board is similar to LS2080ARDB board with few differences
It hosts LS2081A SoC
Default boot source is QSPI-boot
It does not have IFC interface
RTC and QSPI flash device are different
It provides QIXIS access via I2C
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
QSPI-boot is supported on LS2088ARDB RevF board with LS2088A SoC.
LS2088ARDB RevF Board has limitation that QIXIS can not be accessed.
CONFIG_FSL_QIXIS is not enabled.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This allows using PCIe NIC without enabling DPAA FMan.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Mingkai Hu <mingkai.hu@nxp.com>
Acked-by: Mingkai Hu <mingkai.hu@nxp.com>
This allows using PCIe NIC without enabling DPAA FMan.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Mingkai Hu <mingkai.hu@nxp.com>
Acked-by: Mingkai Hu <mingkai.hu@nxp.com>
ls1012ardb, ls1046ardb, ls2080ardb have S25FS512S flash which does
not support Bank Address Register commands.
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
trini: Make Kconfig SPL_xxx entires only show if SPL, so that we don't
get Kconfig errors on platforms without SPL, ie sandbox (without SPL).
Signed-off-by: Tom Rini <trini@konsulko.com>
The original commit for the MCF54418TWR ColdFire development board
support defined a 'CONFIG_SYS_FAULT_ECCONFIG_SYS_NO_FLASHHO_LINK_DOWN'
which obviously has a rogue 'CONFIG_SYS_NO_FLASH' embedded in the
intended 'CONFIG_SYS_FAULT_ECHO_LINK_DOWN' define.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
This converts the following to Kconfig:
CONFIG_CMD_IMMAP
Also move this command out of the cmd/ directory since it is
PowerPC-specific.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present IDE support is controlled by CONFIG_CMD_IDE. Add a separate
CONFIG_IDE option so that IDE support can be enabled without requiring
the 'ide' command.
Update existing users and move the ide driver into drivers/block since
it should not be in common/.
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_CMD_HDMIDETECT
Note that we cannot do 'default y if VIDEO' because this option is only
enabled for a small subset of mx6 boards. Also this command is is not a
great implementation (it doesn't use driver model).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_CMD_HD44760
Also drop CONFIG_CMD_HD44780 which appears to be a typo.
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_CMD_HASH
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Rework slightly, enable on some boards again]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_CMD_FPGA_LOADBP
CONFIG_CMD_FPGA_LOADFS
CONFIG_CMD_FPGA_LOADMK
CONFIG_CMD_FPGA_LOADP
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_CMD_ETHSW
Also enable it for sandbox to increase build coverage.
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_CMD_EEPROM
CONFIG_CMD_EEPROM_LAYOUT
CONFIG_EEPROM_LAYOUT_HELP_STRING
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Rework Kconfig logic slightly, define EEPROM location on TI eval
platforms]
Signed-off-by: Tom Rini <trini@konsulko.com>
This is only used by one board and always set to 0x51. Drop this option.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Now that dtt is gone, this is not used. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
This subsystem is quite old. It has been replaced with a driver-model
version (UCLASS_THERMAL). Boards are free to convert to that if required,
but here is a removal patch that could be applied in the meantime.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
This subsystem has not been converted to driver model, there is only one
driver and only one board that uses it. Drop it and its CONFIG option.
Also drop the rtc4543 RTC driver since it uses TWS.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This option is only defined to a non-default value by canyonlands, which
needs conversion to driver model (where the I2C address would be defined
by the device tree).
Drop this option.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
This converts the following to Kconfig:
CONFIG_DS4510
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
This option enables a command in the driver. But the functions defined by
the driver are not called anywhere else in U-Boot. So it does not seem
useful to have this driver without its commands.
Drop this option, move the header file out of the common include/
directory and make all the function static.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
This option is only used in one driver and two boards. It does not seem
worth having the ability to remove this part of the support.
Drop the option.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Commit 94e3c8c4fd ("crypto/fsl - Add progressive hashing support
using hardware acceleration.") created entries for CONFIG_SHA1,
CONFIG_SHA256, CONFIG_SHA_HW_ACCEL, and CONFIG_SHA_PROG_HW_ACCEL.
However, no defconfig has migrated to it. Complete the move by first
adding additional logic to various Kconfig files to select this when
required and then use the moveconfig tool. In many cases we can select
these because they are required to implement other drivers. We also
correct how we include the various hashing algorithms in SPL.
This commit was generated as follows (after Kconfig additions):
[1] tools/moveconfig.py -y SHA1 SHA256 SHA_HW_ACCEL
[2] tools/moveconfig.py -y SHA_PROG_HW_ACCEL
Note:
We cannot move SHA_HW_ACCEL and SHA_PROG_HW_ACCEL simultaneously
because there is dependency between them.
Cc: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Cc: Naveen Burmi <NaveenBurmi@freescale.com>
Cc: Po Liu <po.liu@freescale.com>
Cc: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Cc: Priyanka Jain <Priyanka.Jain@freescale.com>
Cc: Shaohui Xie <Shaohui.Xie@freescale.com>
Cc: Chunhe Lan <Chunhe.Lan@freescale.com>
Cc: Chander Kashyap <k.chander@samsung.com>
Cc: Steve Rae <steve.rae@raedomain.com>
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: Feng Li <feng.li_2@nxp.com>
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Sumit Garg <sumit.garg@nxp.com>
Cc: Mingkai Hu <Mingkai.Hu@freescale.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Akshay Saraswat <akshay.s@samsung.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
We rename CONFIG_FIT_DISABLE_SHA256 to CONFIG_FIT_ENABLE_SHA256_SUPPORT which
is enabled by default and now a positive option. Convert the handful of boards
that were disabling it before to save space.
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: Lukasz Dalek <luk0104@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SPL_BOARD_INIT
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
[trini: Update the Kconfig logic]
Signed-off-by: Tom Rini <trini@konsulko.com>
There are two UARTs on the board, so enable the clock for the
second one as well.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add support for the EHCI USB.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add support for rebooting the board using the ROHM BD9571MWV I2C PMIC,
but keep the CPU reboot option as a fallback.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add support for the AVB ethernet on the Salvator-X board.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add support for the SD card slots on the Salvator-X board.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The UART uses internal SCIF clock except on R8A7795 H3 WS1.0 .
Use the internal clock and ignore the early version of the chip.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Set default device tree file in the salvator-x_defconfig
and use it in the environment.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Move these two Kconfig symbols to the salvator-x_defconfig.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Update the CONFIG_SYS_TEXT_BASE to match BL2 Rev.1.0.9 and newer,
which loads the U-Boot to 0x50000000 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add config and defconfig for the Arria10 and update socfpga_common.h.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Enable more DM drivers. The imx I2C/MMC DM drivers needs DM_GPIO
enabled. The 74x164 drivers needs SOFT_SPI and DM_GPIO enabled.
So needs to enable them together.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Sync with Linux commit 308ac756("Merge tag 'gpio-v4.11-3'").
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefan Agner <stefan.agner@toradex.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Let the runtime code can set the mmcdev and mmcroot based
on the devno using mmc_get_env_dev instead of defining
separately in build-time configs using mmc_late_init func.
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add runtime, modeboot env which is setting mmcboot, or
nandboot based on the bootdevice so-that conditional
macros b/w MMC and NAND for CONFIG_BOOTCOMMAND should
be avoided in config files.
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Let the runtime code can set the mmcdev and mmcroot based
on the devno using mmc_get_env_dev instead of defining
separately in build-time configs using mmc_late_init func.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add runtime, modeboot env which is setting mmcboot, or
nandboot based on the bootdevice so-that conditional
macros b/w MMC and NAND for CONFIG_BOOTCOMMAND should
be avoided in config files.
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
- Add workaround code to make LD20 SoC boot from ARM Trusted Firmware
- Sync DT with Linux to fix DTC warnings
- Add new SoC support code
- Misc fix, updates
This patch updates the mksunxiboot tool to optionally add
the default device tree name string to the SPL header. This
information can be used by the firmware upgrade tools to
protect users from harming themselves by trying to upgrade
to an incompatible bootloader.
The primary use case here is a non-removable bootable media
(such as NAND, eMMC or SPI flash), which already may have
a properly working, but a little bit outdated bootloader
installed. For example, the user may download or build a
new U-Boot image for "Cubieboard", and then attemept to
install it on a "Cubieboard2" hardware by mistake as a
replacement for the already existing bootloader. If this
happens, the flash programming tool can identify this
problem and warn the user.
The size of the SPL header is also increased from 64 bytes
to 96 bytes to provide enough space for the device tree name
string.
[Andre: split patch to remove OF_LIST hash feature]
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The Allwinner SoCs with 64-bit cores use an ARM Trusted Firmware binary,
which needs to be loaded alongside U-Boot proper.
Set the respective Kconfig options to let them select this feature and
also automatically build the FIT image.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[Rename Kconfig path to arch/arm/mach-sunxi/Kconfig]
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The SPL stack is usually located at the end of SRAM A1, where it grows
towards the end of the SPL.
For the really big AArch64 binaries the stack overwrites code pretty
soon, so move the SPL stack to the end of SRAM A2, which is unused at this
time.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Jagan Teki <jagan@openedev.com>
Reserve enough space below the kernel base.
The assumed address map is:
80000000 - 80ffffff : for IPP
81000000 - 81ffffff : for ARM secure
82000000 - : for Linux
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This new flag can be added to DM device drivers, which need to do some
final configuration before U-Boot exits and the OS (e.g. Linux) is
started. The remove functions of those drivers will get called at
this stage to do these last-stage configuration steps.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Convert the pci_mmc driver over to driver model and migrate all x86 boards
that use it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
- Add #undef CONFIG_DM_MMC_OPS to omap3_logic in the SPL build case, to
match other TI platforms in the same situation.
Signed-off-by: Tom Rini <trini@konsulko.com>
Due to a typo, the 24 bit-per-pixel configuration ends in 24BMP
instead of 24BPP. This change renames it throughout the source tree
for consistency and to make moving these options into Kconfig easier
and less error-prone.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Some DVI monitors don't show anything in HDMI mode since audio stream
confuses them. To solve this situation, this commit adds HDMI flag in
timing data and sets it accordingly during edid parsing.
First existence of extension block is checked. If it exists and it is
CEA861 extension, then data blocks are checked for presence of HDMI
vendor specific data block. If it is present, HDMI flag is set.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Simon Glass <sjg@chromium.org>
Follow the exiting logic for the i.MX options when migrating this
option.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marek Vasut <marex@denx.de>
The following options are migrated over fully now:
- USB_EHCI_ATMEL
- USB_EHCI_MARVELL
- USB_EHCI_MX6
- USB_EHCI_MX7
- USB_EHCI_MSM
- USB_EHCI_ZYNQ
- USB_EHCI_GENERIC
This also requires fixing the depends on USB_EHCI_MARVELL as it's used
by Orion5X and Kirkwood as well.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Migrate the rest of the users of CONFIG_USB_EHCI_HCD over to Kconfig.
For a few SoCs, imply or default y this if USB is enabled. In some
cases we had not already migrated to CONFIG_USB so do that as well.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marek Vasut <marex@denx.de>
In order to be able to migrate the various SoC EHCI CONFIG options we
first need to finish the switch from CONFIG_USB_EHCI to
CONFIG_USB_EHCI_HCD.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marek Vasut <marex@denx.de>
The symbol CONFIG_OMAP3_LOGIC_USE_NEW_PRODUCT_ID was recently dropped
from usage and CONFIG_OMAP3_MICRON_DDR is unused in code.
Signed-off-by: Tom Rini <trini@konsulko.com>
Move this entry to Kconfig. As it is a hardware watchdog, select
HW_WATCHDOG. While we could default to enabling this for all platforms,
it is currently only enabled by default on AM33XX, so keep that logic
today.
Cc: Roger Meier <r.meier@siemens.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The symbols CONFIG_OMAP3_GPIO_X control if we enable the clocks for a
given GPIO bank in U-Boot. select the required banks for each target.
In some cases we need to also migrate from CONFIG_USB_EHCI (deprecated,
in include/configs/) to CONFIG_USB_EHCI_HCD as we only require the GPIO
bank to be enabled if USB is also enabled.
Signed-off-by: Tom Rini <trini@konsulko.com>
This driver is used often enough such that we want to have this enabled
by default on any ARCH_OMAP2PLUS board, and this only compiles on
ARCH_OMAP2PLUS due to required defines, so mark that as the depends.
Signed-off-by: Tom Rini <trini@konsulko.com>
We no longer have a need for a per-board CONFIG_OMAP3_xxx define (we
have CONFIG_TARGET_xxx when this is required), so drop these unused
references.
Signed-off-by: Tom Rini <trini@konsulko.com>
While there are a few different OMAP4 SoCs, today we always set
CONFIG_OMAP4430 and CONFIG_OMAP44XX. Convert the few test of
CONFIG_OMAP4430 to CONFIG_OMAP44XX.
Cc: Marek Vasut <marex@denx.de>
Cc: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Tom Rini <trini@konsulko.com>
We make use of CONFIG_OMAP3_EVM today to know when to do a specific
tweak in MUSB. This can be tested on via CONFIG_TARGET_OMAP3_EVM
instead, so switch there so we can drop the now unused symbol
CONFIG_OMAP3_EVM. In investigating what to do about the symbol usage we
see that the cairo board defines the same function, but never called it
(as it does not define CONFIG_OMAP3_EVM) and was just returning anyhow,
so drop that function from that board.
Cc: "Albert ARIBAUD (3ADEV)" <albert.aribaud@3adev.fr>
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
While in theory this value could be used in places outside of "omap5"
(such as OMAP4), we only make use of it today in OMAP5, so place the
Kconfig entry there. Given that Kconfig lets us provide a default, we
drop CONFIG_DEFAULT_OMAP_RESET_TIME_MAX_USEC entirely. The contents of
doc/README.omap-reset-time make a good help entry, so adjust them
slightly and delete the file. Move the comment about range to where we
use the value now, and have Kconfig enforce the upper bound.
Signed-off-by: Tom Rini <trini@konsulko.com>
In the two cases in the code where we use CONFIG_OMAP as a useful test
currently we can make use of CONFIG_ARCH_OMAP2PLUS instead. With that
changed we can drop all defines of CONFIG_OMAP. While in here,
CONFIG_OMAP3430 is only defined and then never used, so drop.
Signed-off-by: Tom Rini <trini@konsulko.com>
