Some PCIe-based MiniPCIe cards are broken and they do not ground PIN 43
which is required by PCIe mini CEM specs. Such broken cards are incorrectly
detected as mSATA cards because SATA specs requires that PIN 43 on mSATA
cards has to be disconnected.
PIN 43 on Turris Omnia is used only for MiniPCIe/mSATA card detection by
software in U-Boot SPL. Allow to override that U-Boot SPL detection by a
new "omnia_msata_slot" env variable (to value "pcie" or "sata") so broken
MiniPCIe cards can be used in combo mSATA/MiniPCIe slot too.
As configuration of PCIe vs SATA functionality is done in U-Boot SPL,
it is required to change env variable in permanent storage and reset the
board to take effect.
To force PCIe mode for broken MiniPCIe cards, call U-Boot commands:
=> setenv omnia_msata_slot pcie
=> saveenv
=> reset
Signed-off-by: Pali Rohár <pali@kernel.org>
By default use primary serdes map with PCIe function in combined
miniPCIe/mSATA slot. When SATA is detected change serdes map variable at
runtime.
Signed-off-by: Pali Rohár <pali@kernel.org>
BootROM maps SPI Flash to fixed address 0xD4000000 and this mapping is
active also when BootROM is executing binary kwbimage headers, which
includes also U-Boot SPL.
Therefore no initialization code is required to access SPI Flags from
U-Boot SPL. In proper U-Boot it is remapped to other location.
So in mvebu implementation of env_sf_get_env_addr() function returns
0xD4000000 when running in SPL and NULL when in proper U-Boot.
This change would allow to use U-Boot ENV in U-Boot SPL. Normally it is not
possible to read ENV because it is too big and U-Boot SPL does not have
such big malloc() pool to real all ENV variables.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
This function is empty, drop it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Sean Anderson <seanga2@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Steven Lawrance <steven.lawrance@softathome.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Manish Tomar's email bounces. Remove it, and reassign the config he was
maintaining to the primary maintainer for the board.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Whole section about USB/eLBC configuration seems to be P1020 specific. So
add ifdefs to not compile it on other platforms (e.g. P2020).
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Like for first 1G SDRAM map, do not enable Caching-inhibited nor Guarded
attribute for second 1G SDRAM mapping. Whole 2G SDRAM should use caches and
also allow speculative loading (by not setting Guarded attribute).
Also enable Memory Coherency attribute for second 1G SDRAM map. In commit
316f0d0f8f ("powerpc: mpc85xx: Fix static TLB table for SDRAM") it was
enabled for all SDRAM maps on all other boards, just missed this one case.
As a last thing, first 1G SDRAM map has wrong comment, so adjust it.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
When MPC85xx_PMUXCR_SDHC_WP is set then SDHC controller automatically makes
inserted SD card readonly if GPIO[9] is active.
In some design GPIO[9] pin does not have to be connected to SD card
write-protect pin and can be used as GPIO.
So do not set MPC85xx_PMUXCR_SDHC_WP bit when GPIO[9] is not used for
SDHC_WP functionality.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
As written in comment, P2020 has two possible SD switch configurations.
Extend code to detect both of them.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Like in all other checks in checkboard() function, do not hang on error.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
When env support is disabled then usage of env_init() or env_relocate()
generates linker errors. So do not compile env_init() or env_relocate()
in SPL code when env support is disabled in SPL.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
For now, this only provides reset and poweroff functions.
Signed-off-by: Michael Walle <michael@walle.cc>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
There is an user-selectable SYS_HAS_ARMV8_SECURE_BASE, which has the
same meaning but is just for the ls1043ardb board. As no in-tree config
uses this, drop it and replace it with something more sophiticated:
ARMV8_PSCI_RELOCATE. This option will then enable the ARMV8_SECURE_BASE
option which is used as the base to relocate the PSCI code (or any code
in the secure region, but that is only PSCI). A SoC (or board) can now
opt-in into having such a secure region by enabling
SYS_HAS_ARMV8_SECURE_BASE. Enable it for the LS1043A SoC, where it was
possible to relocate the PSCI code before as well as on the LS1028A SoC
where there will be PSCI support soon.
Additionally, make ARMV8_PSCI and SEC_FIRMWARE_ARMV8_PSCI exclusive.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
As removal of nds32 has been ack'd for the Linux kernel, remove support
here as well.
Cc: Rick Chen <rick@andestech.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Rick Chen <rick@andestech.com>
In arch/arm/mach-imx/imx8m/soc.c there's an implementation of
board_fix_fdt() introduced by commit 35bb60787b. Remove the
redundant one to avoid failed to build from source when enabling
CONFIG_OF_BOARD_FIXUP.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: uboot-imx <uboot-imx@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Since COUNTER_FREQUENCY is obselete, so set cntfrq_el0 if
CONFIG_COUNTER_FREQUENCY is valid
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@vrull.eu>
Since versal has CONFIG_COUNTER_FREQUENCY, so use it. And
COUNTER_FREQUENCY will be dropped.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Enable DM_SERIAL for both U_Boot and the SPL. The uart4 and its pinmux
are already marked with u-boot,dm-spl but we need to move the call to
preloader_console_init() after spl_init() to avoid a board hang
as dm can't be used until after spl_init().
Remove the manual config of the UART pinmux now that it is no longer
needed.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Tested-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
Enable CONFIG_DM_SERIAL. uart2 and its pinmux was already
marked with u-boot,dm-spl.
move the preloader_console_init() call after spl_init() to
avoid board hang
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Enable CONFIG_DM_SERIAL. uart2 and its pinmux was already
marked with u-boot,dm-spl.
move the preloader_console_init() call after spl_early_init() to
avoid board hang
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The Sancloud BeagleBone Enhanced Extended WiFi (BBE Extended WiFi) has
its own devicetree file and the board can be identified by the 2nd
letter of the config string within the common EEPROM.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
The Sancloud BeagleBone Enhanced Lite (BBE Lite) has its own devicetree
file and the board can be identified by the 2nd letter of the config
string within the common EEPROM.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
The Globalscale Technologies Sheevaplug board has the network chip
Marvell 88E1116R. Use uclass mvgbe and the compatible driver M88E1310
driver to bring up Ethernet.
- Remove CONFIG_RESET_PHY_R symbol from all board files
- Use uclass mvgbe to bring up the network. And remove ad-hoc code.
- Enable CONFIG_PHY_MARVELL to properly configure the network.
- Miscellaneous changes: Move constants to .c file and remove header file
board/Marvell/sheevaplug/sheevaplug.h, use BIT macro, and add/cleanup
comments.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
The Colibri PXA270 has been end-of-life since quite a while and would
require more and more maintenance (e.g. DM conversions).
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
The GW74xx is based on the i.MX 8M Plus SoC featuring:
- LPDDR4 DRAM
- eMMC FLASH
- Gateworks System Controller
- PCIe Gen 3.0 switch (build option)
- USB 3.0 HUB
- USB Type-C front panel connector
- GPS
- 3-axis accelerometer
- CAN bus
- 6x GbE RJ45 front-panel jacks
- 1x IMX8M FEC RGMII GbE (with Passive PoE)
- 5x IMX8M EQOS RGMII 6 port GbE Switch
(1x with 802.3af class 5 Active PoE)
- RS232/RS485/RS422 serial transceiver
- MIPI header (DSI/CSI/GPIO/PWM/I2S)
- DigI/O header (UART/GPIO/I2C/ADC)
- 802.11ac WiFi
- Bluetooth BLE
- 3x MiniPCIe sockets with PCI/USB
- 1x M.2 Socket with USB2.0, PCIe, and dual-SIM
- PMIC
- Wide range DC input supply (8V to 60V DC)
Do the following to add support for this and future imx8mp-venice boards:
- add dts
- add DRAM config
- add PMIC config
- add IMX8MP support in spl.c and venice.c
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Gateworks produces many products from a single PCB with subloaded
components. Add an additional two levels of dtb name matching so that
for example a GW7400-A matches the dtb name of gw74xx.dtb
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Use the common GSC driver.
This allows us to do some additional cleanup:
- use the GSC driver functions
- move waiting for the EEPROM to the SPL int (it will always be ready
after this)
- move eeprom functions into eeprom file and elimate GSC_I2C_BUS
- eliminate some redundant EEPROM reads (the EEPROM must be read in
SPL before relocation, in SPL after relocation, and in U-Boot init.
All subsequent uses can use the global structure)
- remove unnecessary header files and alphabatize includes
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Use the common GSC driver.
This allows us to do some additional cleanup:
- rename gsc{.c,.h} to eeprom{.c.h} for clarity
- collapse eeprom_get_dev
- remove unnecessary header files and alphabatize includes
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Drop optional support for the ancient Apalis iMX6 V1.0 hardware which
had the UART wired as DCE rather than DTE.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
This fixes the following crash when run on a Colibri iMX7S aka solo:
Colibri iMX7 # usb start
starting USB...
Bus usb@30b10000: USB EHCI 1.00
Bus usb@30b20000:
The i.MX 7Solo has only one single USB OTG1 but no USB host port. Trying
to initialize the nonexisting port just crashes.
While at it also drop board_usb_phy_mode() which is also no longer used
in the driver model age.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Drop Apalis iMX8X platform as it never left sample state and is no
longer supported.
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
DT node name should be generic, therefore rename atsha204a@64 to crypto@64.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Turris Omnia uses first MAC address from OTP for second ethernet interface.
Second MAC address for third interface and third MAC address for first
interface.
Other Turris routers do not have this rotate by one mapping. So add
function parameter for specifying id of the first ethernet interface.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Atsha device is used prior relocation and at this early stage BSS does not
have to be ready yet. So do not cache Atsha device in BSS.
Fixes support for other Turris routers.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
OTP code is not Atsha generic but also it is not Omnia specific. It is
common for all Turris routers which use Atsha cryptochip for storing OTP.
So move this common Turris specific Atsha OTP code from Turris Omnia into
separate file. It will be used also by other Turris routers.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Allow to specify input parameters, define all available mbox commands
supported by CZ.NIC's secure firmware and also Marvell's fuse.bin firmware
and fix parsing response from Marvell OTP commands.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Generic A3720 mbox code is currently in Turris Mox specific board file
board/CZ.NIC/turris_mox/mox_sp.c. Move it to board independent arch file
arch/arm/mach-mvebu/armada3700/mbox.c.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
When storing the UBoot Environment in for example EXT4,
the U-Boot build is broken for several reasons:
1. armada-385-turris-omnia-u-boot.dtsi will not allow
CONFIG_ENV_OFFSET and CONFIG_ENV_SIZE to be undefined
2. armada-37xx/board.c ft_board_setup function does not
exist if CONFIG_ENV_IS_IN_SPI_FLASH is not defined
This commit changes these files so that selecting a
different location for the environment is possible.
Signed-off-by: Rogier Stam <rogier@unrailed.org>
Reviewed-by: Pali Rohár <pali@kernel.org>
Xilinx has been acquired by AMD that's why emails should be also updated.
The patch is updating .mailmap file and also MAINTAINERS files as was done
by commit 5cd1ecb994 ("ppc: qemu: Update MAINTAINERS for correct email
address").
The rest of my emails are not going to change.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
A number of rk3229/rk3288 DT files are synced from Linux.
Add a maintainer to look after them and to help with
review and testing.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Google Veyron rk3288 DT files are synced from Linux.
Add a maintainer to look after them and to help with
review and testing.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
MK808 is a RK3066-based board with 1 USB host and 1 USB OTG port,
HDMI and a micro-SD card slot. It also includes on-board NAND
and 1GB of SDRAM.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
- DM9000 DM support
- tftp server bug fix
- mdio ofnode support functions
- Various phy fixes and improvements.
[trini: Fixup merge conflicts in drivers/net/phy/ethernet_id.c
drivers/net/phy/phy.c include/phy.h]
Add a structure which defines the information that is needed for
executing capsule updates on a platform. Some information in the
structure like the dfu string is used for making the update process
more robust while some information like the per platform image GUIDs
is used for fixing issues. Initialise this structure in the board
file, and use the information for the capsule updates.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
The GW7903 is based on the i.MX 8M Mini SoC featuring:
- LPDDR4 DRAM
- eMMC FLASH
- microSD socket with voltage select support
- Gateworks System Controller
- M.2 A-E Socket with USB2.0 and PCIe
- MiniPCIe Socket with PCIe, USB2.0, and SIM
- IMX8M FEC
- RS232/RS485/RS422 serial transceiver
- LIS2DE12 3-axis accelerometer
- front panel LED's
- off-board isolated digital I/O
- Wide range DC power input
- 802.3at PoE
- PMIC
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Add new board based on the Toradex Verdin iMX8M Mini SoM, the MX8Menlo.
The board is a compatible replacement for i.MX53 M53Menlo and features
USB, multiple UARTs, ethernet, LEDs, SD and eMMC.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Max Krummenacher <max.krummenacher@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
The TI DP83867 phy has been replaced with the MaxLinear GPY111 phy due
to part availability.
Add support for it by adding LED config and dt-prop based internal delay
config tx-delay/rx-delay per PHY ID.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Add support for Data Modul i.MX8M Mini eDM SBC board. This is an
evaluation board for various custom display units. Currently
supported are serial console, ethernet, eMMC, SD, SPI NOR,
USB host and USB OTG.
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
The serial number is located at offset 0x14 of the EEPROM
under i2c0 bus at address 0x54.
To print the serial number in Linux:
SERNUM=$(cat /proc/device-tree/serial-number)
echo $SERNUM
Signed-off-by: Fabio Estevam <festevam@denx.de>
Currently, the DDR type is retrieved by iteracting inside an array
of possible DDR types.
This may take saveral attempts, which slows the overall U-Boot process
and does not provide a good user experience:
U-Boot SPL 2021.07 (Feb 28 2022 - 06:39:32 +0000)
DDRINFO: Cfg attempt: [ 1/6 ]
DDRINFO(M): mr5-8 [ 0xff000010 ]
DDRINFO(T): mr5-8 [ 0x5000010 ]
resetting ...
U-Boot SPL 2021.07 (Feb 28 2022 - 06:39:32 +0000)
DDRINFO: Cfg attempt: [ 2/6 ]
DDRINFO(M): mr5-8 [ 0xff000010 ]
DDRINFO(T): mr5-8 [ 0x1061010 ]
resetting ...
U-Boot SPL 2021.07 (Feb 28 2022 - 06:39:32 +0000)
DDRINFO: Cfg attempt: [ 3/6 ]
DDRINFO(M): mr5-8 [ 0xff000010 ]
DDRINFO(T): mr5-8 [ 0xff000010 ]
Normal Boot
WDT: Not starting
Trying to boot from MMC2
NOTICE: BL31: v2.5(release):v2.5
NOTICE: BL31: Built : 07:12:44, Jan 24 2022
Improve the boot time by retrieving the correct DDR information from
the EEPROM:
U-Boot SPL 2022.04-rc4-00045-g6d02bc40d58c (Mar 19 2022 - 08:22:29 -0300)
DDRINFO(D): Kingston 4096G
DDRINFO(M): mr5-8 [ 0xff000010 ]
DDRINFO(E): mr5-8 [ 0xff000010 ]
Normal Boot
WDT: Started watchdog@30280000 with servicing (60s timeout)
Trying to boot from MMC2
NOTICE: BL31: v2.5(release):v2.5
NOTICE: BL31: Built : 22:28:11, Mar 15 2022
Based on the original code from Compulab's U-Boot.
Tested on a imx8mm-cl-iot-gate board populated with 4GB of RAM.
Signed-off-by: Fabio Estevam <festevam@denx.de>
imx8mm-cl-iot-gate supports multiple DDR sizes and models.
The DDR type can be retrieved from the EEPROM, so add SPL code
that can be used to get the DDR information.
Based on the original code from Compulab's U-Boot.
Signed-off-by: Fabio Estevam <festevam@denx.de>
The power/bd71837.h should no longer be included, since V1.1 SoM
uses only the PCA9450 PMIC and the BD71837 support was removed.
Drop the header too.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Max Krummenacher <max.krummenacher@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Now that it is possible to use regulator-fixed-clock make use
of it. This makes U-Boot detect the PHY on first cold-boot.
This commit also adjusts the code in setup_fec and follows
how it is done in mx6ullevk.c
This commit also slows down the boot-process by about 150ms
as it now waits for the regulator-fixed-clock voltage that
drives the PHY to go up.
If you rely on very fast boot-speeds and don't need ethernet
for your boot-process you can safely revert the changes on
imx6ull-colibri.dtsi
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Toradex uses the variable variant to distinguish between modules with
eMMC, NAND with wifi and NAND without wifi.
This variable is set on every boot. Set this variable also if we have a
NAND module without wifi to prevent issues.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
U-Boot should never save the environment unasked.
This also avoids storing broken fdt_module to flash.
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
U-Boot should never save the environment unasked.
This also avoids storing broken ftd_file to eMMC.
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Rename board_early_init_f() to board_early_init(), since this function
has nothing to do with actual board_early_init_f() as used throughout
U-Boot. The board_early_init() is function local to this board used to
configure UART and WDT pinmux. Wrap init_uart_clk() into this function
so that early UART init would be all in one place. Turn the function
into __weak one, so it could be overridden in case custom carrier board
uses different UART or needs custom IOMUX settings.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Max Krummenacher <max.krummenacher@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
If M33 handshake is successful, TPM and DSI panel MUX setting is
done by M33, no need to set them.
If handshake is failed or M33 is not booted, continue the TPM
and DSI panel MUX setting
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Update DDR PHY settings to support LPDDR4 mode only by adjusting
DQ VREF ctrl, ODT and pads drive strength.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Found the lposc fuse loading having impact to cpu idle in kernel.
Without the loading in dual boot mode, kernel will hang after idle
for a while.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When M33 is LPAV owner in dual boot, DDR, PCC5, CGC2 won't be reset
during APD reset. So no need to init DDR again after reboot, but need to
reconfigure the PLL4 PFD/PFDDIV/LPAV NIC etc, because kernel may
change or disable some of them.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add a new ddr script, defconfig for ND
Configure the clock for ND mode
changing A35 to 960MHz for OD mode
Update NIC CLK for the various modes
Introduce clock_init_early/late, late is used after pmic voltage
setting, early is used in the very early stage for upower mu, lpuart and
etc.
Note: NIC runs at 324MHz, 442MHz has some random kernel hang issue with
cpuidle enabled now.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This workaround is not needed on i.MX8ULP proto-1B EVK as board has
fixed the problem. Because we don't support proto-1A any longer,
remove the PMIC settings.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Conversion to DM_SERIAL is mandatory.
Select DM_SERIAL and add a imx6q-tbs2910-u-boot.dtsi file
that describes the nodes that require dm-pre-reloc, which allows
the DM model to configure the UART pinctrl early.
Remove the now unneeded board UART initialization.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Tested-by: Soeren Moch <smoch@web.de>
With DM_SERIAL selected, it is no longer needed board code to
initialize the UART.
Describe the nodes that require dm-pre-reloc, which allows
the DM model to configure the UART pinctrl early.
Remove the now unneeded board UART initialization.
Signed-off-by: Fabio Estevam <festevam@denx.de>
DM is not used for the SPL and a generic DT is used in the SPL
which requires no fixups. Remove the call in the SPL and move the function
into the U-Boot code.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Since DM_SERIAL is used for U-Boot we no longer need legacy UART code in
common.c shared by the SPL and U-Boot. Move the legacy UART config to
the non-DM SPL.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
convert to DM_I2C for U-Boot while leaving SPL legacy I2C:
- Move I2C config from common to SPL
- Move PMIC config from common to SPL (no need to re-configure pmic)
- add DM_I2C support to eeprom/gsc functions shared by SPL and U-Boot
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The Ethernet controller and PHY use the device tree info to
configure themselves, so it's not necessary to manually do it
in the board file. This permits the removal of a bunch of headers
as well.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Acked-by: Peng Fan <peng.fan@nxp.com>
With the correct settings described in the device-tree the PHY settings
in the board init are no longer required. The values are taken from the
linux device tree.
The PHY latency settings are derived from the phy-mode property and the
voltage seetings are done via the regulator.
Suggested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Tested-by: Marek Vasut <marex@denx.de> # 8MNANOD4-EVK
Reviewed-by: Fabio Estevam <festevam@gmail.com>
LS(1021/1012/1028/1043/1046/1088/2088), LX2160, LX2162
platforms are enabled with JR driver model.
removed sec_init() call from board files.
sec is initialized based on job ring information processed
from device tree.
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: Michael Walle <michael@walle.cc>
i.MX8(QM/QXP) - added support for JR driver model.
sec is initialized based on job ring information processed
from device tree.
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
i.MX8MM/MN/MP/MQ - added support for JR driver model.
sec is initialized based on job ring information processed
from device tree.
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Currently we require PHY interface mode to be known when
finding/creating the PHY - the functions
* phy_connect_phy_id()
* phy_device_create()
* create_phy_by_mask()
* search_for_existing_phy()
* get_phy_device_by_mask()
* phy_find_by_mask()
all require the interface parameter, but the only thing done with it is
that it is assigned to phydev->interface.
This makes it impossible to find a PHY device without overwriting the
set mode.
Since the interface mode is not used during .probe() and should be used
at first in .config(), drop the interface parameter from these
functions. Make the default value of phydev->interface (in
phy_device_create()) to be PHY_INTERFACE_MODE_NA. Move the interface
parameter to phy_connect_dev(), where it should be.
Change all occurrences treewide. In occurrences where we don't call
phy_connect_dev() for some reason (they only configure the PHY without
connecting it to an ethernet controller), set
phydev->interface = value from phy_find_by_mask call.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Rename constant PHY_INTERFACE_MODE_NONE to PHY_INTERFACE_MODE_NA to make
it compatible with Linux' naming.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Add helpers ofnode_read_phy_mode() and dev_read_phy_mode() to parse the
"phy-mode" / "phy-connection-type" property. Add corresponding UT test.
Use them treewide.
This allows us to inline the phy_get_interface_by_name() into
ofnode_read_phy_mode(), since the former is not used anymore.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
We use 'DEBUG' and not 'CONFIG_DEBUG' tree-wide for debug code that is
left in, and not wrapped by some other regular debugging type print
macro.
Cc: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These values are only used in one file, reference them more directly.
Cc: Kamil Lulko <kamil.lulko@gmail.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This code is only used on the corvus platform, so migrate the LED on/off
code to this platform and remove it from the CONFIG namespace. In
theory, this should likely be moved to the modern GPIO LED driver as a
further cleanup.
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
This converts the following to Kconfig:
CONFIG_CM_INIT
CONFIG_CM_REMAP
CONFIG_CM_SPD_DETECT
CONFIG_CM_MULTIPLE_SSRAM
CONFIG_CM_TCRAM
We make the first three of these options be always enabled, as that
matches usage. We select the last two based on how they were defined in
armcoremodule.h. This also allows us to remove some unused code in
board/armltd/integrator/lowlevel_init.S
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Let CONFIG_TARGET_QEMU_VIRT imply CONFIG_CMD_SBI.
The sbi command provides detailed information about the SBI.
It is useful to test the discovery of extensions.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
xilinx:
- Allow booting bigger kernels till 100MB
zynqmp:
- DT updates (reset IDs)
- Remove unneeded low level uart initialization from psu_init*
- Enable PWM features
- Add support for 1EG device
serial_zynq:
- Change fifo behavior in DEBUG mode
zynq_sdhci:
- Fix BASECLK setting calculation
clk_zynqmp:
- Add support for showing video clock
gpio:
- Update slg driver to handle DT flags
net:
- Update ethernet_id code to support also DM_ETH_PHY
- Add support for DM_ETH_PHY in gem driver
- Enable dynamic mode for SGMII config in gem driver
pwm:
- Add driver for cadence PWM
versal:
- Add support for reserved memory
firmware:
- Handle PD enabling for SPL
- Add support for IOUSLCR SGMII configurations
include:
- Sync phy.h with Linux
- Update xilinx power domain dt binding headers
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYkxUZwAKCRDKSWXLKUoM
IXJ2AKCQcoFK7wanCCvZfuEJCSwO5E4eCACginE2CFVXKcY1P8ta4ESusjY2TH0=
=HOoS
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.07-rc1-v2' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2022.07-rc1 v2
xilinx:
- Allow booting bigger kernels till 100MB
zynqmp:
- DT updates (reset IDs)
- Remove unneeded low level uart initialization from psu_init*
- Enable PWM features
- Add support for 1EG device
serial_zynq:
- Change fifo behavior in DEBUG mode
zynq_sdhci:
- Fix BASECLK setting calculation
clk_zynqmp:
- Add support for showing video clock
gpio:
- Update slg driver to handle DT flags
net:
- Update ethernet_id code to support also DM_ETH_PHY
- Add support for DM_ETH_PHY in gem driver
- Enable dynamic mode for SGMII config in gem driver
pwm:
- Add driver for cadence PWM
versal:
- Add support for reserved memory
firmware:
- Handle PD enabling for SPL
- Add support for IOUSLCR SGMII configurations
include:
- Sync phy.h with Linux
- Update xilinx power domain dt binding headers
A big part is the DM pinctrl driver, which allows us to get rid of quite
some custom pinmux code and make the whole port much more robust. Many
thanks to Samuel for that nice contribution! There are some more or less
cosmetic warnings about missing clocks right now, I will send the trivial
fixes for that later.
Another big chunk is the mkimage upgrade, which adds RISC-V and TOC0
(secure images) support. Both features are unused at the moment, but I
have an always-secure board that will use that once the DT lands in the
kernel.
On top of those big things we have some smaller fixes, improving the
I2C DM support, fixing some H6/H616 early clock setup and improving the
eMMC boot partition support.
The gitlab CI completed successfully, including the build test for all
161 sunxi boards. I also boot tested on a A64, A20, H3, H6, and F1C100
board. USB, SD card, eMMC, and Ethernet all work there (where applicable).
Call into k3-ddrss driver to fixup device tree and resize the available
amount of DDR if ECC is enabled.
A second fixup is required from A53 SPL to take the fixup as done from
R5 SPL and apply it to DT passed to A53 U-boot, which in turn passes
this to the OS.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Use the appropriate fdtdec_setup_mem_size_base and
fdtdec_setup_bank_size calls in dram_init and dram_bank_init to pull
these values from DT, where they are already available, instead of
hardcoding them.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Now that mkimage can generate TOC0 images, and the SPL can interpret
them, hook up the build infrastructure so the user can choose which
image type to build. Since the absolute load address is stored in the
TOC0 header, that information must be passed to mkimage.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This is now handled automatically by the pinctrl driver.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
These options are not currently enabled anywhere. Any new users should
use DM clocks and pinctrl.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This is now handled automatically by the pinctrl driver.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmJH28ocHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyDv4B/9FBx95f7zR6WmguG05
VyBchjphsRSuXHb7NieVNNEIpCJu+zw8YutngN2Q8KWIbM9o1OZnrNGxuKR9s+Px
ivMXytGGsIa74XXhxv2boX151R1a5TG4UPf4Vn20qxmUiScE4FaoW5wQHG2vGqxd
/LbzENNCA1A41/RGGysqyY8nQgOEY+Iass+OaHe7XjngcCfY5oY4IRqJ/Ak7ojkv
Vm46i+KCTuyBlcMDjAwDsukSmzsujz2FyzZU1Uy62N8quEdXgrlIA/Yh4oarZ+BO
5W/BJe1rClbnBkMJJn71GUlmnYrioYeUvxvIYwZWooe0Hgr+Iv1vOXv8aJ4hBsdc
yoje
=SwGu
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2022.07-a' of https://source.denx.de/u-boot/custodians/u-boot-at91 into next
First set of u-boot-at91 features for the 2022.07 cycle:
This feature set includes the new driver for the Atmel TCB timer,
alignment in DT for sama7g5 and sama7g5ek board, one Kconfig conversion
for external reset, and the usage of Galois tables from ROM for sama5d2
device.
Use the semihosting_enabled function to determine whether or not to
enable semihosting devices. This allows for graceful fallback in the
event a debugger is not attached.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
This adds support for booting entirely from JTAG while using a
hard-coded RCW. With these steps, it is not necessary to program a
"good" RCW using CodeWarrior. The method here can be performed with any
JTAG adapter supported by OpenOCD, including the on-board CMSIS-DAP
(albeit very slowly).
These steps require LS1046A support in OpenOCD, which was added in [1].
[1] 5b70c1f679/
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
[trini: Add reference to doc/board/nxp/ls1046ardb.rst]
This converts the readme for this board to rST. I have tried not to
change any semantics from the original (though I did convert MB to M).
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
The ARMv8-R64 architecture introduces optional VMSA (paging based MMU)
support in the EL1/0 translation regime, which makes that part mostly
compatible to ARMv8-A.
Add a new board variant to describe the "BASE-R64" FVP model, which
inherits a lot from the existing v8-A FVP support. One major difference
is that the memory map in "inverted": DRAM starts at 0x0, MMIO is at
2GB [1].
* Create new TARGET_VEXPRESS64_BASER_FVP target, sharing most of the
exising configuration.
* Implement inverted memory map in vexpress_aemv8.h
* Create vexpress_aemv8r defconfig
* Provide an MMU memory map for the BASER_FVP
* Update vexpress64 documentation
At the moment the boot-wrapper is the only supported secure firmware. As
there is no official DT for the board yet, we rely on it being supplied
by the boot-wrapper into U-Boot, so use OF_HAS_PRIOR_STAGE, and go with
a dummy DT for now.
[1] https://developer.arm.com/documentation/100964/1114/Base-Platform/Base---memory/BaseR-Platform-memory-map
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
[Andre: rebase and add Linux kernel header]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[trini: Add MAINTAINERS entry for Peter]
So far the DRAM size for both the Juno and the FVP model were hardcoded
in our config header file. For the Juno this is fine, as all models have
8 GiB of DRAM, but the DRAM size can be configured on the model command
line.
Drop the fixed DRAM size setup, instead look up the size in the device
tree, that we now have for every board. This allows a user to inject
a DT with the proper size, and be able to use the full amount of DRAM.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
In preparation for the ARMv8-R64 FVP support, which has DRAM mapped at
0x0, generalise the page table generation, by using symbolic names for
the address ranges instead of fixed numbers.
We already define the base of the DRAM and MMIO regions, so just use
those symbols in the page table description. Rename V2M_BASE to the more
speaking V2M_DRAM_BASE on the way.
On the VExpress memory map, the address space right after 4GB is of no
particular interest to software, as the whole of DRAM is mapped at 32GB
instead. The first 2 GB alias to the lower 2GB of DRAM mapped below 4GB,
so we skip this part and map some more of the high DRAM, should anyone
need it.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The defconfigs for the Arm Juno board and the FVP model are quite large,
setting a lot of platform-fixed variables like SYS_TEXT_BASE.
As those values are not really a user choice, let's provide default
values for them in our Kconfig file, so a lot of cruft can be removed
from the defconfig files.
This also moves the driver selection out of there, since this is again
not something a user should really decide on. Instead we allow users to
enable or disable subsystems, and select the appropriate drivers based
on that in the Kconfig file.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The FVP base model is relying on a DT for Linux operation, so there is
no reason we would need to rely on hardcoded information for U-Boot.
Letting U-Boot use a DT will open up the usage of actual peripherals,
beyond the support for semihosting only.
Enable OF_CONTROL in the Kconfig, and use the latest dts files from
Linux. Depending on whether we use the boot-wrapper or TF-A, there is
already a DTB provided or not, respectively.
To cover the boot-wrapper, we add an arm64 Linux kernel header, which
allows the boot-wrapper to treat U-Boot like a Linux kernel. U-Boot will
find the pointer to the DTB in x0, and will use it.
Even though TF-A carries a DT, at the moment this is not made available
to non-secure world, so to not break users, we use the U-Boot provided
DTB copy in that case. For some reason TF-A puts some DT like structure
at the address x0 is pointing at, but that is very small and doesn't
carry any hardware information. Make the code to ignore those small DTBs.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
At the moment we define three "VExpress64" boards in arch/arm/Kconfig,
plus have a second Kconfig file in board/armltd/Kconfig.
One of those three boards is actually bogus (TARGET_VEXPRESS64_AEMV8A),
that stanza looks like being forgotten in a previous cleanup.
To remove the clutter from the generic Kconfig file, just define some
ARCH_VEXPRESS64 symbol there, enable some common options, and do the
board/model specific configuration in the board/armltd Kconfig file.
That allows to streamline and fine tune the configuration later, and
to also pull a lot of "non user choices" out of the defconfigs.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This converts the following to Kconfig:
CONFIG_NORFLASH_PS32BIT
Note that we also attempt to correct the behavior of the code here,
which had been testing for "NORFLASH_PS32BIT" which would never be set,
instead check for the now set "CONFIG_NORFLASH_PS32BIT", which results
in some behavior change.
Cc: TsiChung Liew <Tsi-Chung.Liew@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_LSCHLV2
CONFIG_LSXHL
Cc: Michael Walle <michael@walle.cc>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Michael Walle <michael@walle.cc>
This CONFIG option is used in one place, so pick a more direct name and
migrate to Kconfig. Rework the code slightly.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_KM_COGE5UN
CONFIG_KM_KIRKWOOD_128M16
CONFIG_KM_KIRKWOOD
CONFIG_KM_KIRKWOOD_PCI
CONFIG_KM_NUSA
CONFIG_KM_SUSE2
Cc: Holger Brunck <holger.brunck@hitachienergy.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Holger Brunck <holger.brunck@hitachienergy.com>
The only usage of CONFIG_KMTEGR1 can be replaced by
CONFIG_TARGET_KMTEGR1 so do so and remove this other symbol.
Cc: Holger Brunck <holger.brunck@hitachienergy.com>
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Holger Brunck <holger.brunck@hitachienergy.com>
This platform is the only one to set these options, so define them in
the board Kconfig file.
Cc: Angelo Dureghello <angelo@sysam.it>
Signed-off-by: Tom Rini <trini@konsulko.com>
Both of these variables are used in a few hard-coded ways to set some
string values or print something to the user. In almost all cases, it's
just as useful to hard-code the value used. The exception here is
printing something closer to correct board name for p1_p2_rdb machines.
This can be done using something from the device tree, but for now
hard-code a non-CONFIG based value instead.
Signed-off-by: Tom Rini <trini@konsulko.com>
Set blue led on at boot time in order to highlight that u-boot is loaded.
This is done for all sama5d2 based boards which contain an RGB led.
Signed-off-by: Mihai Sain <mihai.sain@microchip.com>
The QEMU platform has a function defined to get the random number
generator(RNG) device. However, the RNG device can be obtained simply
by searching for a device belonging to the RNG uclass. Remove the
superfluous platform function defined for the QEMU platform for
getting the RNG device.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
The SPL does not update the memory node with the dram size from EEPROM
but instead we can use get_ram_size which does a simple memory test
to determine the available RAM. Update PHYS_SDRAM_SIZE to 4GiB as that
is the max used on the Venice boards.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
commit 7c84319af9c7 ("dm: gpio: Correct use of -ENODEV in drivers")
changed the return code for an I2C NAK from -ENODEV to -EREMOTEIO.
Update the gsc_i2c_read and gsc_i2c_write functions for this change
to properly retry the transaction on a NAK meaning the GSC is busy.
Fixes: 7c84319af9 ("dm: gpio: Correct use of -ENODEV in drivers")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Versal can also have reserved space in DT which u-boot has to avoid to
placing self to that location. The same change was done in ZynqMP by commit
ce39ee28ec ("zynqmp: Do not place u-boot to reserved memory location")
and also for microblaze by commit d7b5cc89d3 ("microblaze: Do not place
u-boot to reserved memory location").
The patch was tested by adding reserved-memory node to DT and check via
bdinfo back.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/15426fa6d64835dd23c5c8c12bbfc97306fb6098.1647527129.git.michal.simek@xilinx.com
This does not use driver model and is more than two years past the
migration date. Drop it.
It can be added back later if needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
This does not use driver model and is more than two years past the
migration date. Drop it.
It can be added back later if needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Drop the Kconfigs which are not used and all references to them. In
particular, this drops CONFIG_VIDEO to avoid confusion and allow us to
eventually rename CONFIG_DM_VIDEO to CONFIG_VIDEO.
Also drop the prototype for video_get_info_str() which is no-longer used.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Jason Liu <jason.hui.liu@nxp.com>
Commit 5bc4cd05d7 ("sunxi: move non-essential code out of s_init()")
moved the call to eth_init_board() from s_init() into board_init_f().
This means it's now only called from the SPL, which makes sense for
most of the other moved low-level functions. However the GMAC pinmux and
clock setup in eth_init_board() was not happy about that, so it broke
the sun7i GMAC.
Since Ethernet is of no use in the SPL anyway, just move the call into
board_init(), which is only run in U-Boot proper.
This fixes Ethernet operation for the A20 SoCs, which broke in
v2022.04-rc1, with the above mentioned commit.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Tested-by: Petr Štetiar <ynezz@true.cz> [a20-olinuxino-lime2]
Add following two new PCI class codes defines into pci_ids.h include file:
PCI_CLASS_BRIDGE_PCI_NORMAL
PCI_CLASS_BRIDGE_PCI_SUBTRACTIVE
And use these defines in all U-Boot code for describing PCI class codes for
normal and subtractive PCI bridges.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This converts the following to Kconfig:
CONFIG_LCD_INFO
CONFIG_LCD_LOGO
CONFIG_LCD_INFO_BELOW_LOGO
CONFIG_LCD_IN_PSRAM
Cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_ATMEL_LCD
CONFIG_ATMEL_LCD_BGR555
CONFIG_ATMEL_LCD_RGB565
CONFIG_GURNARD_SPLASH
Signed-off-by: Tom Rini <trini@konsulko.com>
This variable is used once and is noted as board-specific. Use the
value directly with a comment.
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This symbol is used only once, and in comparison with an unset symbol,
so drop it.
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_AT91SAM9G10EK
CONFIG_AT91SAM9261EK
CONFIG_AT91SAM9G10
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_AT91SAM9G20EK
CONFIG_AT91SAM9260EK
CONFIG_AT91SAM9G20EK_2MMC
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
A small number of i.MX6/7 and vf610 boards have not enabled DM_ETH yet.
Given the state of the rest of the platform, enable DM_ETH.
Cc: Alison Wang <alison.wang@nxp.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Richard Hu <richard.hu@technexion.com>
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Cc: Uri Mashiach <uri.mashiach@compulab.co.il>
Signed-off-by: Tom Rini <trini@konsulko.com>
Add support for Kevin, an RK3399-based convertible chromebook that is
very similar to Bob. This patch is mostly based on existing support for
Bob, with only minor changes for Kevin-specific things.
Unlike other Gru boards, coreboot sets Kevin's center logic to 925 mV,
so adjust it here in the dts as well. The rk3399-gru-kevin devicetree
has an unknown event code reference which has to be defined, set it
to the Linux counterpart. The new defconfig is copied from Bob with the
diffconfig:
DEFAULT_DEVICE_TREE "rk3399-gru-bob" -> "rk3399-gru-kevin"
DEFAULT_FDT_FILE "rockchip/rk3399-gru-bob.dtb" -> "rockchip/rk3399-gru-kevin.dtb"
VIDEO_ROCKCHIP_MAX_XRES 1280 -> 2400
VIDEO_ROCKCHIP_MAX_YRES 800 -> 1600
+TARGET_CHROMEBOOK_KEVIN y
With this Kevin can boot from SPI flash to a usable U-Boot prompt on the
display with the keyboard working, but cannot boot into Linux for
unknown reasons.
eMMC starts in a working state but fails to re-init, microSD card works
but at a lower-than-expected speed, USB works but causes a hang on
de-init. There are known workarounds to solve eMMC and USB issues.
Cc: Marty E. Plummer <hanetzer@startmail.com>
Cc: Simon Glass <sjg@chromium.org>
[Alper: commit message, resync config with Bob, update MAINTAINERS,
add to Rockchip doc, add Kconfig help message, set regulator]
Co-developed-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
The RK3399 SoC needs to know the voltage value provided by some
regulators, which is done by setting relevant register bits. Configure
these the way other RK3399 boards do, but with the same values as are
set in the equivalent code in coreboot.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
microblaze:
- Add support for reserved memory
xilinx:
- Update FRU code with MAC reading
zynqmp:
- Remove double AMS setting
- DT updates (mostly for SOMs)
- Add support for zcu106 rev 1.0
zynq:
- Update nand binding
nand:
- Aligned zynq_nand to upstream DT binding
net:
- Add support for ethernet-phy-id
mmc:
- Workaround CD in zynq_sdhci driver also for ZynqMP
- Add support for dynamic/run-time SD config for SOMs
gpio:
- Add driver for slg7xl45106
firmware:
- Add support for dynamic SD config
power-domain:
- Update zynqmp driver with the latest firmware
video:
- Add skeleton driver for DP and DPDMA
i2c:
- Fix i2c to work with QEMU
pinctrl:
- Add driver for zynqmp pinctrl driver
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYjIBkgAKCRDKSWXLKUoM
IYUwAKCYRBxb59BFq4MRvTbNcRZ7H4oGIQCfVUl3x9KZ7nFZaYAaBXFBxwna+PE=
=irCR
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.07-rc1' of https://source.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2022.07-rc1
microblaze:
- Add support for reserved memory
xilinx:
- Update FRU code with MAC reading
zynqmp:
- Remove double AMS setting
- DT updates (mostly for SOMs)
- Add support for zcu106 rev 1.0
zynq:
- Update nand binding
nand:
- Aligned zynq_nand to upstream DT binding
net:
- Add support for ethernet-phy-id
mmc:
- Workaround CD in zynq_sdhci driver also for ZynqMP
- Add support for dynamic/run-time SD config for SOMs
gpio:
- Add driver for slg7xl45106
firmware:
- Add support for dynamic SD config
power-domain:
- Update zynqmp driver with the latest firmware
video:
- Add skeleton driver for DP and DPDMA
i2c:
- Fix i2c to work with QEMU
pinctrl:
- Add driver for zynqmp pinctrl driver
stm32mp1 bsec: Add permanent lock write support
stm32mp1 bsec: Add dev in function description
cmd_stboard: Update test on misc_read() result
video: fix the check of return value of clk_set_rate in stm32_ltdc
DT: Alignment with kernel v5.17 for stm32mp15
DT: Add USB OTG pinctrl and regulator in SPL for DHCOR
DT: Move vdd_io extras into Avenger96 extras
DT: Add DFU support for DHCOM recovery
ram: stm32mp1: Unconditionally enable ASR
psci: Implement PSCI system suspend and DRAM SSR for stm32mp
-----BEGIN PGP SIGNATURE-----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=H4+P
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20220315' of https://source.denx.de/u-boot/custodians/u-boot-stm
mtd: add NAND write protect support to stm32_fmc2_nand
stm32mp1 bsec: Add permanent lock write support
stm32mp1 bsec: Add dev in function description
cmd_stboard: Update test on misc_read() result
video: fix the check of return value of clk_set_rate in stm32_ltdc
DT: Alignment with kernel v5.17 for stm32mp15
DT: Add USB OTG pinctrl and regulator in SPL for DHCOR
DT: Move vdd_io extras into Avenger96 extras
DT: Add DFU support for DHCOM recovery
ram: stm32mp1: Unconditionally enable ASR
psci: Implement PSCI system suspend and DRAM SSR for stm32mp
"kendryte" is the marketing name for the K210 RISC-V SoC produced by
Canaan Inc. Rather than "kendryte,k210", use the usual "canaan,k210"
vendor,SoC compatibility string format in the device tree files and
use the SoC name for file names.
With these changes, the device tree files are more in sync with the
Linux kernel DTS and drivers, making uboot device tree usable by the
kernel.
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Update management of misc_read/misc_write, which now returns length of
data after the commit 8729b1ae2c ("misc: Update read() and write()
methods to return bytes xfered"): raise a error when the result is not
the expected length.
Fixes: 658fde8a36 ("board: stm32mp1: stboard: lock the OTP after programming")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
- convert Nokia RX-51 to CONFIG_DM_VIDEO
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCYi+zvw4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXIReAJ9JS06uOjNFmOBdfpsOI2jnVdWABQCbB8nvUh19
jbftZtj+18fhFuNb1r4=
=3vpL
-----END PGP SIGNATURE-----
Merge tag 'video-20220314' of https://source.denx.de/u-boot/custodians/u-boot-video
- fix display of the u-boot logo on Apple devices
- convert Nokia RX-51 to CONFIG_DM_VIDEO
Initialization and power on operations of links have been moved under the
link device in the Sierra SerDes driver. Also, the UCLASS of
sierra_phy_provider has been changed to UCLASS_MISC.
Therefore, fix the probing of SerDes0 instance accordingly.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Georgi Vlaev <g-vlaev@ti.com>
This adds platform code and the device tree for the Phytium Pomelo Board.
The initial support comprises the UART and the PCIE.
Signed-off-by: weichangzheng <nicholas_zheng@outlook.com>
With updated device trees now supporting pinmuxing for USB,
ethernet, MMC, and other peripherals necessary to start MLO
and U-Boot, the hard-coded pinmux options can be removed since
they are now handed by DM and only muxed when the respective
peripheral needs it.
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Derald D. Woods <woods.technical@gmail.com>
With recent fixes to USB pinmuxing in the device trees, there
is no need to hard-code the pinmuxing in this table. It is
all handled in DM now.
Signed-off-by: Adam Ford <aford173@gmail.com>
The ethernet controller is DM compliant, and the device tree
defines it. There is no need to manually handle pulling
the ethernet out of reset.
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Derald D. Woods <woods.technical@gmail.com>
The PMIC enables power to the MMC card by default, but depending
on the state it was left when restarted, it's possible the MMC
may be powered down.
This patch patch explicitly tells the twl4030 to power the MMC.
Based on commits [1][2].
[1] 64fd2d2614
[2] 27b6534491
Signed-off-by: Romain Naour <romain.naour@gmail.com>
With DM_MMC working for both SPL and U-Boot, this patch removes
the legacy style of initializing the MMC driver.
Based on omap3_logic: 42140dd096.
Signed-off-by: Romain Naour <romain.naour@gmail.com>
This hook can be implmented using events, for the three boards that
actually use it.
Add the event type and event handlers. Drop CONFIG_MISC_INIT_F since we
can just use CONFIG_EVENT to control this. Since sandbox always enables
CONFIG_EVENT, we can drop the defconfig lines there too.
Signed-off-by: Simon Glass <sjg@chromium.org>
Currently we only support to load the environment from raw MMC or FAT
locations on Allwinner boards. With the advent of SPI flash we probably
also want to support using the environment there, so we need to become
a bit more flexible.
Change the environment priority function to take the boot source into
account. When booted from eMMC or SD card, we use FAT or MMC, if
configured, as before.
If we are booted from SPI flash, we try to use the environment from
there, if possible. The same is true for NAND flash booting, although
this is somewhat theoretical right now (as untested).
This way we can use the same image for SD and SPI flash booting, which
allows us to simply copy a booted image from SD card to the SPI flash,
for instance.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Mechanically convert video_hw_init() function to UCLASS_VIDEO probe
callback and replace CONFIG_CFB_CONSOLE by CONFIG_DM_VIDEO.
As framebuffer base address is setup by the bootloader which loads U-Boot,
set plat->base to that fixed framebuffer address.
This change was tested in qemu n900 machine and is working fine.
What does not work is CONFIG_VIDEO_LOGO, seems to be buggy.
Signed-off-by: Pali Rohár <pali@kernel.org>
Since commit 5d94cbd1dc ("scripts: Makefile.lib: generate
dsdt_generated.c instead of dsdt.c"), the file generated
is named dsdt_generated.c instead of dsdt.c.
So all files .gitignore referencing dsdt.c should be
upated with dsdt_generated.c.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This add the initial support of the broadcom reference
board bcm96753ref with a bcm6753 SoC.
This board has 1 GB of RAM, 256 MB of flash (nand),
2 USB port, 1 UART, and 4 ethernet ports.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Add support to read MAC addresses from mac address multirecord.
Check if multi record is found, then jump to mac address multirecord by
comparing the record type field. If it matches mac address
multirecord(0xD2), then copy mac addresses.
Copy these read MAC address in xilinx_read_eeprom_fru so that they are
updated to eth*addr in board_late_init_xilinx().
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/18f31bc528820934854ea5fd9dc581778fc1e40c.1645624855.git.michal.simek@xilinx.com
In board_late_init_xilinx() eth*addr are updated from the values read from
eeprom. Ideally the MAC addresses are updated sequencially. So if any
MAC address is invalid, it means there are no further valid values.
So optimise this logic by replacing continue with break.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/efef0d07add5d5777396ea111ad75411dc402db3.1645624855.git.michal.simek@xilinx.com
fru_checksum function is simply adding all the bytes and returning the
sum. If the data passed to this function is all zero's then it will
return 0, and the functions calling this api will assume that checksum
is correct. Ideally this is not good. Fix this by returning error if all
the data is 0's.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/ac0366fe55c60a818a3f9ed33d96826c817d5520.1645624855.git.michal.simek@xilinx.com
We only want to call do_board_detect() if CONFIG_TI_I2C_BOARD_DETECT
is set. Same as done for am64.
This makes it possible to add a custom am65 based board design to
U-Boot that does not use this board detection mechanism.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Commit 369e532691 ("ddr: marvell: a38x: allow board specific ODT
configuration") added the odt_config member to struct
mv_ddr_topology_map ahead of the clk_enable and ck_delay members. This
means that any boards that configured either of clk_enable or ck_delay
needed to have their board topology updated. This affects the x530 and
clearfog boards. Other A38x boards don't touch any of the trailing
members of mv_ddr_topology_map so don't need updating.
Fixes: 369e532691 ("ddr: marvell: a38x: allow board specific ODT configuration")
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
The branch_if_master macro jumps to a label if the CPU is the "master"
core, which we define as having all affinity levels set to 0. To check
for this condition, we need to mask off some bits from the MPIDR
register, then compare the remaining register value against zero.
The implementation of this was slighly broken (it preserved the upper
RES0 bits), overly complicated and hard to understand, especially since
it lacked comments. The same was true for the very similar
branch_if_slave macro.
Use a much shorter assembly sequence for those checks, use the same
masking for both macros (just negate the final branch), and put some
comments on them, to make it clear what the code does.
This allows to drop the second temporary register for branch_if_master,
so we adjust all call sites as well.
Also use the opportunity to remove a misleading comment: the macro
works fine on SoCs with multiple clusters. Judging by the commit
message, the original problem with the Juno SoC stems from the fact that
the master CPU *can* be configured to be from cluster 1, so the
assumption that the master CPU has all affinity values set to 0 does not
hold there. But this is already mentioned above in a comment, so remove
the extra comment.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This patch scans the cmdline from the Samsung SBL (second stage
bootloader) and stores the parameters board_id=N and lcdtype=N
in order to augment the DTB for different board and LCD types.
We then add a custom ft_board_setup() callback that will inspect
the DTB and patch it using the stored LCD type. At this point
we know which product we are dealing with, so using the passed
board_id we can also print the board variant for diagnostics.
We patch the Codina, Skomer and Kyle DTBs to use the right
LCD type as passed in lcdtype from the SBL.
This also creates an infrastructure for handling any other
Samsung U8500 board variants that may need a slightly augmented
DTB.
Cc: Markuss Broks <markuss.broks@gmail.com>
Cc: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
To make sure we get a working console as soon as possible in the SPL the
UART pins require to be configured earlier. This is especially
true for the pins of UART3, since the PDU001 board uses this UART for
the console by default.
Signed-off-by: Felix Brack <fb@ltec.ch>
The changes from commit 0dba45864b ("arm: Init the debug UART")
prevent the early debug UART from being initialized correctly.
To fix this we not just configure the pin multiplexer but add setting up
early clocks.
Signed-off-by: Felix Brack <fb@ltec.ch>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This board has an internal watchdog which supervises the board startup.
Although, the initial state of the watchdog is configurable, it is
enabled by default. In board_late_init(), which means almost everything
worked as expected, disable the watchdog.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Most of the time it is very useful to have the version of the board
management controller. Now that we have a driver, print it during
startup.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The current console output is:
DRAM: 4 GiB
DDR 4 GiB (DDR3, 32-bit, CL=11, ECC on)
The size is printed twice and we can save one line of console output if
we join both lines. The new output is as follows:
DRAM: 4 GiB (DDR3, 32-bit, CL=11, ECC on)
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
There is a conflict between the static file
lib/acpi/dsdt.c and the file dsdt.c generated
dynamicaly by scripts/Makefile.lib. When a
mrproper is done, the static file dsdt.c is
removed. If a build with acpi enabled is
launched after, the following error is raised:
CC lib/acpi/acpi_table.o
make[2]: *** No rule to make target 'lib/acpi/dsdt.asl', needed by 'lib/acpi/dsdt.c'. Stop.
scripts/Makefile.build:394: recipe for target 'lib/acpi' failed
To avoid such error, the generated file is named
dsdt_generated.c instead of dstdt.c.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Tested-by: Heiko Thiery <heiko.thiery@gmail.com>
The commit 0dba45864b ("arm: Init the debug UART") calls
debug_uart_init() from crt0.S but it won't work because SOC is not
configured yet. That's why create board_debug_uart_init() which calls
psu_init() via new psu_uboot_init() earlier before the first access to UART
in SPL. In full U-Boot call psu_uboot_init() only when
CONFIG_ZYNQMP_PSU_INIT_ENABLED is enabled.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/878dc2daaa8685346f889989fbfb98b2e44da7fb.1645104518.git.michal.simek@xilinx.com
ZYNQMP_PSU_INIT_ENABLED is called only when BOARD_EARLY_INIT_F is defined
that's why cover this dependency in Kconfig.
board_early_init_f() is only part related to
CONFIG_ZYNQMP_PSU_INIT_ENABLED which is disabled now that's why disable
BOARD_EARLY_INIT_F and also build board_early_init_f() only when
CONFIG_BOARD_EARLY_INIT_F is enabled.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/d89253ec1590cd513dcd4bfbedebae618bd6d605.1645104518.git.michal.simek@xilinx.com
The commit 9855034397 ("fdt: Don't call board_fdt_blob_setup() without
OF_BOARD") forced to enable OF_BOARD for platforms which provide DT
externally. Zynq/ZynqMP boards are using this feature for a long time
that's why there is a need to enable it by default.
Also code expects to return error in case of error that's why also fill it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/9f11bbffe2849f4da7d72712082d579262fe8fd8.1645104518.git.michal.simek@xilinx.com
Add support for ethernet on the imx8mn-ddr4-evk.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
The function wrongly will return the card detection status of the SD card
(USDHC2) for the eMMC (USDHC1). Thus booting from eMMC without an inserted
SD card will fail.
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
The GW7902 is based on the i.MX 8M Mini / Nano SoC featuring:
- LPDDR4 DRAM
- eMMC FLASH
- Gateworks System Controller
- LTE CAT M1 modem
- USB 2.0 HUB
- M.2 Socket with USB2.0, PCIe, and dual-SIM
- IMX8M FEC
- PCIe based GbE
- RS232/RS485/RS422 serial transceiver
- GPS
- CAN bus
- WiFi / Bluetooth
- MIPI header (DSI/CSI/GPIO/PWM/I2S)
- PMIC
To add support for the i.MX8M Nano GW7902:
- Add imx8mn-venice dts/defconfig/include
- Add imx8mn-gw7902 dts
- Add imx8mn-2gb lpddr4 dram configs
- Add misc support for IMX8M Nano SoC
- rename imx8mm-venice.c to venice.c as it is no longer imx8mm specific
- update README with differences for IMX8MN vs IMX8MM
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
With binman generating flash.bin, it's not longer necessary to
specify either the location of ATF nor is it necessary to
specify building flash.bin, so let's update the build instructions
to remove those. While in here, update the revision of ATF and
DDR firmware so both Mini and Nano reference the same revision.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Use IS_ENABLED(CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG) to make the code
more readable and fix checkpatch.pl warning
Signed-off-by: Tommaso Merciai <tomm.merciai@gmail.com>
- a37xx: pci: Cleanup and minor fix for root port check (Pali)
- pci: mvebu: Ensure that root port is always on root zero bus (Pali)
- kwbimage: Fix dumping DATA registers for v0 images (Pali)
- kwbimage: Support for parsing extended v0 format (Pali)
- a37xx: Fix code and update DTS files to upstream version (Pali)
- a37xx: Fix and extend building memory map (Pali)
- ddr: marvell: a38x: fix BYTE_HOMOGENEOUS_SPLIT_OUT decision (Marek)
- mvebu: Optionally reset board on DDR training failure (Marek)
Armada 3720 DTS files in upstream kernel use ethernet nodes named
'ethernet@30000' and 'ethernet@40000'. U-Boot have them named 'neta@30000'
and 'neta@40000'. To have Turris Mox U-Boot board code independent of
ethernet node names, find ethernet node via alias.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Update the board_fit_config_name_match() to choose the right dtb
based on the board name read from EEPROM.
Also restrict multpile EEPROM reads by verifying if EEPROM is already
read.
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
j721e-sk doesn't have any daughter cards, so disable daughter
card probing inside board_late_init() and spl_board_init() for
j721e-sk.
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
J721E EVM has EEPROM populated at 0x50. J721E SK has EEPROM populated
at next address 0x51 in order to be compatible with RPi. So start
looking for TI specific EEPROM at 0x50, if not found look for EEPROM at
0x51.
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
board_late_init(), setup_board_eeprom_env() and setup_serial() is
called only under CONFIG_BOARD_LATE_INIT, so guard these functions
with the same. Also, reorder these functions to place it under
single #ifdef
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
The Pogoplug E02 board has the network chip Marvell 88E1116R. Convert
to Driver Model and use uclass mvgbe and the compatible driver M88E1118R
to bring up Ethernet.
- Add board_eth_init(), CONFIG_DM_ETH, and CONFIG_PHY_MARVELL
to bring up Ethernet.
- Currently, CONFIG_RESET_PHY_R symbol is used in
arch/arm/mach-kirkwood/include/mach/config.h for all Kirkwood
boards with mv8831116 PHY, with each board defines the function
reset_phy(). Undefine it for this board.
- As the result of the migration to Driver Model, this u-boot image has
grown substantially (about 100K, give or take). The old envs location
at 0x60000 (384k) is no longer possible. Move it to 0xC0000 (768K).
- Miscellaneous changes: Move constants to .c file and remove header file
board/cloudengines/pogo_e02/pogo_e02.h, use CONFIG_SYS_THUMB_BUILD to
keep u-boot image under 512K, use BIT macro, and cleanup comments.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The Dockstar board has the network chip Marvell 88E1116R. Convert to
Ethernet driver model, and use uclass mvgbe and the compatible driver
M88E1118R to bring up Ethernet.
- Add CONFIG_DM_ETH and associated configs.
- Add board_eth_init() to use uclass mvgbe to bring up the network.
And remove ad-hoc code.
- Add CONFIG_PHY_MARVELL to properly configure the network.
- Currently, CONFIG_RESET_PHY_R symbol is used in
arch/arm/mach-kirkwood/include/mach/config.h for all Kirkwood
boards with mv8831116 PHY, with each board defines the function
reset_phy(). Undefine it for this board.
- Miscellaneous changes: Move constants to .c file and remove
header file board/Seagate/dockstar/dockstar.h, use
CONFIG_SYS_THUMB_BUILD to keep u-boot image
under 512K, add CONFIG_HUSH_PARSER, use BIT macro, and cleanup comments.
- Note: This patch is a RESEND for a previous patch:
https://patchwork.ozlabs.org/project/uboot/patch/20210812051854.1340-2-mibodhi@gmail.com/
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
- Currently, CONFIG_RESET_PHY_R symbol is used in
arch/arm/mach-kirkwood/include/mach/config.h for all Kirkwood
boards with mv8831116 PHY, with each board defines the function
reset_phy(). Undefine it for this board.
- Add board_eth_init(), CONFIG_DM_ETH, and CONFIG_PHY_MARVELL
to bring up Ethernet.
- Miscellaneous changes: Move constants to .c file and remove header file
board/iomega/iconnect/iconnect.h. Add CONFIG_HUSH_PARSER, use BIT macro,
and cleanup comments.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The Globalscale Technologies Dreamplug board has the network chip
Marvell 88E1116R. Use uclass mvgbe and the compatible driver M88E1310
driver to bring up Ethernet.
- Currently, CONFIG_RESET_PHY_R symbol is used in
arch/arm/mach-kirkwood/include/mach/config.h for all Kirkwood
boards with mv8831116 PHY, with each board defines the function
reset_phy(). Undefine it for this board.
- Add board_eth_init() to use uclass mvgbe to bring up both network
port 0 and 1. And remove ad-hoc code.
- Enable CONFIG_PHY_MARVELL to properly configure the network.
- Add myself as maintainer (this board seems to be orphaned,
could not contact Jason Cooper using current email).
- Miscellaneous changes: Move constants to .c file and remove header file
board/Marvell/dreamplug/dreamplug.h, cleanup comments.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Pali Rohár <pali@kernel.org>
Currently, if MTD NOR is enabled then U-Boot tries to issue flash
commands even when CFI flash DT node is not present. This causes
access fault on RISC-V emulators or ISS which do not emulate CFI
flash. To handle this issue, we implement is_flash_available() for
qemu-riscv board which will return 1 only if CFI flash DT node is
present.
Fixes: d248627f9d ("riscv: qemu: Enable MTD NOR flash support")
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Enable support for HTIF console so that we can use QEMU RISC-V U-Boot
on RISC-V emulators and ISS having it.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@vrull.eu>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
This is supposed to be a build-system flag. Move it there so we can
define it before linux/kconfig.h is included.
Signed-off-by: Simon Glass <sjg@chromium.org>
This adds initial support for the Toradex Verdin iMX8M Plus Quad 4GB WB
IT V1.0B module. They are strapped to boot from eFuses which are factory
fused to properly boot from their on-module eMMC. U-Boot supports
booting from the on-module eMMC only, SDP support is disabled for now
due to missing i.MX 8M Plus USB support.
Functionality wise the following is known to be working:
- eMMC, 8-bit and 4-bit MMC/SD card slots
- Ethernet both on-module eQoS and FEC (requires PHY on carrier board)
- GPIOs
- I2C
Boot sequence is:
SPL ---> ATF (TF-A) ---> U-boot proper
ATF, U-boot proper and u-boot.dtb images are packed into a FIT image,
loaded by SPL.
Boot:
U-Boot SPL 2022.04-rc1-00164-g21a0312611-dirty (Feb 07 2022 - 11:34:04 +0100)
Quad die, dual rank failed, attempting dual die, single rank configuration.
Normal Boot
WDT: Started watchdog@30280000 with servicing (60s timeout)
Trying to boot from BOOTROM
Find img info 0x&48025a00, size 872
Need continue download 1024
Download 779264, Total size 780424
NOTICE: BL31: v2.2(release):rel_imx_5.4.70_2.3.2_rc1-5-g835a8f67b
NOTICE: BL31: Built : 16:52:37, Aug 26 2021
U-Boot 2022.04-rc1-00164-g21a0312611-dirty (Feb 07 2022 - 11:34:04 +0100)
CPU: Freescale i.MX8MP[8] rev1.1 at 1200 MHz
Reset cause: POR
DRAM: 8 GiB
Core: 78 devices, 18 uclasses, devicetree: separate
WDT: Started watchdog@30280000 with servicing (60s timeout)
MMC: FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... OK
In: serial
Out: serial
Err: serial
Model: Toradex Verdin iMX8M Plus Quad 4GB Wi-Fi / BT IT V1.0B, Serial# 06817281
Carrier: Toradex Verdin Development Board V1.1A, Serial# 10807609
Setting variant to wifi
Net: Hard-coding pdata->enetaddr
eth1: ethernet@30be0000, eth0: ethernet@30bf0000 [PRIME]
Hit any key to stop autoboot: 0
Verdin iMX8MP #
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The function to return the default MMC device for the environment
already has a __weak instance doing exactly the same thing. Remove
the superfluous one.
Signed-off-by: Adam Ford <aford173@gmail.com>
The function to return the default MMC device for the environment
already has a __weak instance doing exactly the same thing. Remove
the superfluous one.
Signed-off-by: Adam Ford <aford173@gmail.com>
Sync with the latest DDR initialization from Phytec, which
uses version 1.2 of NXP's i.MX7D DRAM Register Programming Aid
spreadsheet.
This updated DDR initialization fixes occasional system freeze.
Signed-off-by: Fabio Estevam <festevam@denx.de>
As suggested in commit 028abfd9b1 ("imx8mm-evk: Generate a single
bootable flash.bin again") for imx8mm_evk, it is possible to produce
single bootable image via binman. This restores the original behavior in
distros, where only one boot container is used to create target image.
Perform similar adaptions in order to provide single bootable image for
imx8mn-ddr4-evk derivate.
Update documentation to drop additional step of copying u-boot.itb
Fixes: 353dfe4b43 ("imx8mn-ddr4-evk: switch to use binman")
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The new configs/imx28_xea_sb_defconfig is introduced to facilitate
building the single binary u-boot.sb fox XEA board.
The biggest distinction from "normal" XEA imx28_xea_sb_defconfig is
support for USB mass storage devices (pen drives).
To achieve that, the CONFIG_DM_USB is enabled and supported.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This change provides the possibility to build XEA (imx287 based) board
U-Boot as a single binary (without support for CONFIG_SPL_FRAMEWORK).
The generated u-boot.sb can be used in the factory environment to for
example perform initial setup or HW testing.
It can be used with 'uuu' utility
(SDPS: boot -f /srv/tftp/xea/u-boot.sb)
In the configs/imx28_xea_defconfig one needs to disable following configs:
# CONFIG_SPL_BLK is not set
# CONFIG_SPL_FRAMEWORK is not set
The board_init_ll() is used in arch/arm/cpu/arm926ejs/mxs/start.S, which
is utilized when CONFIG_SPL_FRAMEWORK is disabled.
However, when it is enabled - the arch/arm/cpu/arm926ejs/start.S is used,
which requires the lowlevel_init() function.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Extension boards can be added to Compulab's iot-gate-imx8mm.
We implement extension board manager for detecting the extension
boards.
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: uboot-imx <uboot-imx@nxp.com>
8ULP ROM should read the LPOSC trim BIAS fuse to fill the CGC0
LPOSCCTRL[7:0], but it writes a fixed value on A0.1 revision.
A0.2 will fix the issue in ROM. But A0.1 we have to workaround
it in SPL by setting LPOSCCTRL BIASCURRENT again.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The setting does not have effect because we should set it after
power on the PS16 for NIC AV.
So move it after upower_init which has powered on all PS
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The board use IO9 of PCA6416 on LPI2C0 and TPM0 for MIPI DSI MUX and
backlight. However the LPI2C0 and TPM0 are M33 resources, in this
patch we simply access them, but this is a temporary solution.
We will modify it when M33 FW changes to set MIPI DSI panel as default
path and enable backlight after reset.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add EA iMX7ULP COM board support for building SPL.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
This is the promised second part of the sunxi PR for 2022.04, albeit
technially outside of the merge window. We were working on this full
steam since the beginning of the year, and it deserves to be merged,
I think.
The main attraction is support for the F1C100s SoC, which sports a
venerable ARM926 core. Support for this SoC and the LicheePi Nano board
has been in Linux for years, and U-Boot patches were posted mid last
year already.
The new SoC using ARMv5 also means that the bulk of the new code should
not touch any existing boards, although we did some refactorings first,
of course, which actually cleans up some existing sunxi code.
Compile tested for all 160 sunxi boards, and briefly tested on BananaPi M1,
OrangePi Zero, Pine64 and Pine-H64. Tested by others on their boards,
including F1C100s and F1C200s devices.
Generic Timer Extension is not available on SUNIV.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Add the PDU001 board specific DT files to MAINTAINERS. This should
help for better tracking of changes to these files.
Signed-off-by: Felix Brack <fb@ltec.ch>
The available ram can be limited by ram_top as that depends on the
reserved memory nodes provided by the device-tree (via
board_get_usable_ram_top), so make sure to respect ram_top when setting
up bootm_size to avoid overlapping reserved memory regions (e.g. memory
used by OP-TEE).
The same logic is available in env_get_bootm_size when bootm_size is
not defined by the default environment.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Link: https://lore.kernel.org/r/20220120191730.2009270-1-ricardo@foundries.io
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Commit 045ecf8992 ("configs: enable DM_ETH support for LS1046ARDB")
resulted in the PCI bus no longer being implicitly enumerated.
However, this is necessary for the fdt pcie fixups to work.
Therefore, similar to commit 8b6558bd41 ("board: ls1088ardb:
transition to DM_ETH"), pci_init() is now called in the board_init()
routine when CONFIG_DM_ETH is active.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
CC: Priyanka Jain <priyanka.jain@nxp.com>
Acked-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
IFC-NOR and QSPI are muxed on SoC.
So disable IFC node in dts if QSPI is enabled or disable QSPI node in dts
in case QSPI is not enabled.
"ifc/nor" will be changed to "memory-controller/nor" in linux. So need to
modify "ifc/nor" to "memory-controller/nor" in fdt_path_offset().
Signed-off-by: Jianpeng Bu <jianpeng.bu@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Commit eb1986804d ("configs: enable DM_ETH support for LS1043ARDB")
resulted in the PCI bus no longer being implicitly enumerated.
However, this is necessary for the fdt pcie fixups to work.
Therefore, similar to commit 8b6558bd41 ("board: ls1088ardb:
transition to DM_ETH"), pci_init() is now called in the board_init()
routine when CONFIG_DM_ETH is active.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
CC: Priyanka Jain <priyanka.jain@nxp.com>
CC: Camelia Groza <camelia.groza@nxp.com>
Acked-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The SCRATCHRW4 is only used in secure boot scenario that is unsupported by
our design, so this address can be stolen for storing POST status.
The SCRATCHRW4 is initialized to zero at core rest.
Using a DDR address was unfortunate choice, the DDR at boot time has a
random contend and it happens that sometimes is matching POST magic number.
This behavior can lead to undefined POST behavior and u-boot ending in
failbootcmd command.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This patch adds default defconfig for u-boot update version, the u-boot
update defconfig is a copy of the default (factory) defconfig with:
- adapted text base and environment addresses
- explicit flag that this is a field updated u-boot version
At the time of implementation this version is only used to verify the
update procedure, in future depend on the needs this defconfig can be
extended with additional options.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This was probably broken when mainlining, CONFIG_FSL_DEVICE_DISABLE is
not Kconfig but whitelisted.
It's fine to be without flag as this is always enabled for abec1020
(pg-wcom-ls102xa.h)
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This patch adds default defconfig for u-boot update version, the u-boot
update defconfig is a copy of the default (factory) defconfig with:
- adapted text base and environment addresses
- explicit flag that this is a field updated u-boot version
At the time of implementation this version is only used to verify the
update procedure, in future depend on the needs this defconfig can be
extended with additional options.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Field fail-safe u-boot update procedure for pg-wcom boards is defined and
implemented by patch: 59b3403.
This patch invokes the update procedure for pg-wcom-ls102x designs during
early misc_init_f execution.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This patch provides possibility for field fail-safe u-boot updates.
The implementation can be used on all pg-wcom boards that are booting from
parallel NOR flash.
When used in a board design, provided check_for_uboot_update function will
start new u-boot at defined location if updateduboot envvar is set to yes.
With this implementation it is expected that factory programmed u-boot
will always stay as it is, and optionally new u-boot can be safely
programmed by embedded software when the unit is rolled out on the field.
It is expected check_for_uboot_update to be called early in execution
before relocation (*_f) once SoC is basically initialized and environment
can be read, with this possibilities to not be able to fix a u-boot bug by
a u-boot update are reduced to minimum.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The EBOOTCNT is a reserved persistent static memory area in QRIO,
and similar to BOOTCNT is intended to be used as boot counter location.
Comparable to BOOTCNT that is reserved for u-boot main bootcount
infrastructure, EBOOTCNT is intended to be used for pg-wcom board
specific purposes (e.g implementing early boot counter for fail-safe
u-boot update).
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The PHY for the debug interface was placed on the board for the
pg_wcom_ls102x. Hence only when a piggy is plugged, a RJ45 jack
including magnetics is connected to the MDI of the PHY. Without a
piggy the MDI lines are left floating and it does not make sense to
have an active debug PHY.
In case of expu1 an active PHY without a piggy even led to increased
jitter for syncE.
This patch only deactivates the prst line of the debug PHY when a piggy
is detected persent.
Signed-off-by: Rainer Boschung <rainer.boschung@hitachienergy.com>
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
It is necessary to read the status of the PGY_PRES pin
so that u-boot can react accordingly.
Signed-off-by: Rainer Boschung <rainer.boschung@hitachienergy.com>
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
QRIO library now supports direct read of the test pin status.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
There is a request from HW designers to use this QRIO pin for detecting
DIC26_SELFTEST status instead of a GPIO pin.
This pin is typically used during production for executing POST tests and
starting test ESW bank.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The Ten64 is a networking-oriented MiniITX board
using the NXP LS1088A SoC.
This patch provides the bare minimum to support
Ten64 boards under U-Boot for distroboot.
Some related drivers have not yet been submitted
and this basic support lacks some of the
opinionated defaults provided by our firmware
distribution.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Traverse Technologies Ten64 family boards use a microcontroller
to control low level board functions like startup and reset,
as well as holding details such as the board MAC address.
Communication between the CPU and microcontroller is via
I2C.
To keep the driver structure clean between the Ten64 board
file, DM_I2C, and a future utility command, this driver
has been implemented as a misc uclass device.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The GoFlex Home board has the network chip Marvell 88E1116R.
Use uclass mvgbe and the compatible driver M88E1118R to bring up Ethernet.
- Currently, CONFIG_RESET_PHY_R symbol is used in
arch/arm/mach-kirkwood/include/mach/config.h for all Kirkwood
boards with mv8831116 PHY, with each board defines the function
reset_phy(). Undefine it for this board.
- Add board_eth_init() to use uclass mvgbe to bring up the network.
And remove ad-hoc code.
- Enable CONFIG_PHY_MARVELL to properly configure the network.
- Miscellaneous changes: use CONFIG_SYS_THUMB_BUILD to keep u-boot image
under 512K, use BIT macro, and cleanup comments.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Use versioned URLs for line numbers as branches are moving in the time and
use master branch for mv-ddr-marvell where is up-to-date code.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
a bit delayed, the first batch of the sunxi pull request for this cycle.
This is mostly collecting some patches that were lying around for a
while, plus some recent fixes. Nothing too exciting at this point, but
of course they should be merged nevertheless.
There is the much bigger F1C100s SoC support coming up, which I hope to
be able to send in the next few days, along with the removal of sunxi's
lowlevel_init usage.
Compile tested for all 159 sunxi boards, plus briefly tested on BananaPi
M1, OrangePi Zero, Pine64 and Pine-H64.
For sunxi boards with the AXP209, AXP221, AXP809, and AXP818 PMICs
(plus possibly others, I only confirmed the datasheets for these),
it is sometimes desirable to not boot whenever the device is
plugged in. An example would be when using the NTC CHIP inside a
PocketCHIP.
This provides a configurable option to check if bit 0 of
register 0 of the PMIC says it was powered because of a power button
press (0) or a plug-in event (1). If the value is 1 and this option
is selected, the device shuts down shortly after printing a message
to console stating the reason why it's shutting down. Powering up the
board with the power button is not affected.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
[Andre: reword to speak of boot, remove #ifdefs]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Since DRAM_MEMORY_TYPE_DDR3 is defined let's use it instead of magic
number 3.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Sometimes some ethernet aliases do not exist in U-Boot DT but they
exist in the DT used to boot the system (for example, modified via DT
overlays). In this situation setup_environment is called again in
ft_board_setup() to generate macaddr environment variable for them.
However now the call to fdt_fixup_ethernet() is moved before the call
of ft_board_setup().
Call fdt_fixup_ethernet() again to add MAC addresses for the extra
ethernet aliases.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
[updated commit message]
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Solve compilation issue on undefined CONFIG_SYS_MMC_ENV_DEV when
CONFIG_ENV_IS_IN_MMC is deactivated on STMicroelectronics boards
defconfig
Fixes: 9f97193616 ("board: stm32mp1: use CONFIG_SYS_MMC_ENV_DEV when available")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
MAX_SEARCH_PARTITIONS is the highest possible partition number.
Do not skip the last partition in board_get_alt_info_mmc().
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
- fdt_support: Add fdt_for_each_node_by_compatible() helper macro
(Marek)
- turris_omnia: Fixup SATA or PCIe nodes at runtime in DT blob (Pali)
- pci_mvebu: Add support for Kirkwood PCIe controllers (Pali)
- SPL: More verifications for kwbimage in SPL (Pali)
- mvebu: Remove comphy_update_map() (Pali)
- Minor misc stuff
- meson64_android: define raw parts for bootloader to permit flashing with fastboot
- vim3: configure serial# from ethaddr to permit using fastboot like sei510/610
-----BEGIN PGP SIGNATURE-----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=tP9Y
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20220120' of https://source.denx.de/u-boot/custodians/u-boot-amlogic
- Disable CONFIG_NET_RANDOM_ETHADDR for android configs
- meson64_android: define raw parts for bootloader to permit flashing with fastboot
- vim3: configure serial# from ethaddr to permit using fastboot like sei510/610
Code in board_fix_fdt() already detects connected MOX modules so there is
no need to have custom comphy_update_map() function for setting serdes
speeds.
This change sets phy-mode for MOX SFP module (when present) to sgmii.
Comphy driver then sets sgmii serdes speed for this module to 1.25G.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
On of the MiniPCIe ports on Turris Omnia is also a mSATA port. Whether
it works in SATA or PCIe mode is determined by a strapping pin, which
value is read from the MCU.
We already determine which type of card is connected when configuring
SerDeses.
But until now we left both SATA and PCIe port 0 nodes in device tree
enabled, and so the SATA driver is probed in U-Boot / Linux even if we
know there is no mSATA card, and similarly PCIe driver tries to link on
port 0 even if we know there is mSATA card, not a PCIe card.
Fixup device tree blob to disable SATA node if mSATA card is not
present, and to disable PCIe port 0 node if mSATA card is present.
Do this for U-Boot's DT blob before relocation and also for kernel DT
blob before booting.
This ensures that software does not try to use SATA or PCIe HW when
corresponding PHY is not configured.
Signed-off-by: Pali Rohár <pali@kernel.org>
[ refactored and fixed some issues ]
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Add macro fdt_for_each_node_by_compatible() to allow iterating over
fdt nodes by compatible string.
Convert various usages of
off = fdt_node_offset_by_compatible(fdt, start, compat);
while (off > 0) {
code();
off = fdt_node_offset_by_compatible(fdt, off, compat);
}
and similar, to
fdt_for_each_node_by_compatible(off, fdt, start, compat)
code();
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
gpio:
- Add modepin driver
net:
- Save random mac addresses to eth variable
zynqmp gem:
- Add support for mdio bus DT description
- Add support for reset and SGMII phy configuration
- Reduce timeout for MDIO accesses
zynqmp clk:
- Fix clock handling for gem and usb
phy:
- Add zynqmp phy/serdes driver
serial:
- Add one missing compatible string
microblaze:
- Symbol alignement
- SPL fixups
- Code cleanups
zynqmp:
- Various dt changes, DP pre-reloc, gem resets, gem clocks
- Switch SOM to shared psu configuration
- Move dcache handling to firmware driver
- Workaround gmii2rgmii DT description issue
- Enable broadcasts again
- Change firmware enablement logic
- Small adjustement in firmware driver
versal:
- Support new mmc@ DT nodes
- Fix run time variable handling
- Add missing I2C_PMC ID for power domain
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYeg7sQAKCRDKSWXLKUoM
IVhJAKCAiNx/joEeFBJ0XgThtJzFhCjdMwCfYKY9Ewz4L0n2I56lDgR3UJroct0=
=HtB+
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.04-rc1' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2022.04-rc1
gpio:
- Add modepin driver
net:
- Save random mac addresses to eth variable
zynqmp gem:
- Add support for mdio bus DT description
- Add support for reset and SGMII phy configuration
- Reduce timeout for MDIO accesses
zynqmp clk:
- Fix clock handling for gem and usb
phy:
- Add zynqmp phy/serdes driver
serial:
- Add one missing compatible string
microblaze:
- Symbol alignement
- SPL fixups
- Code cleanups
zynqmp:
- Various dt changes, DP pre-reloc, gem resets, gem clocks
- Switch SOM to shared psu configuration
- Move dcache handling to firmware driver
- Workaround gmii2rgmii DT description issue
- Enable broadcasts again
- Change firmware enablement logic
- Small adjustement in firmware driver
versal:
- Support new mmc@ DT nodes
- Fix run time variable handling
- Add missing I2C_PMC ID for power domain
asm/mmu.h include is currently guarded by CONFIG_ADDR_MAP ifdef because
the header is only present on arm and powerpc. In order to remove the
dependency on this header and the associated ifdef, move init_addr_map()
declaration to init.h, since it is only called during the common init
sequence.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
- Let am335x_evm use the CPSW or PRUSS ethernet.
- Implement timer_get_boot_us in the omap timer driver
- gpmc bitflip, QSPI clock calculation on am437x, da8xx_gpio bugfixes
- Assorted K3 updates
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmHlNOccHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyL0JB/4+sKNWPMgOYvP2uLCC
euRGomhxJ5WmxJVDtJeBIRg0YKSkwnE8JwIN2qqGu15xJnNX9Ck5qnIMPbiZ/io9
ocW5Z/4C4rfJX/OzD6FtmbMNsvG/umVmZkjRU3ryRXKGyNVpVjLQ2EEECaJfk1WZ
Nd/J6/Jo8nafb1x4OeY+F6+xwZAuj7Mrun9SsDSyrIvmEqSnaQNioj+lStkauL51
NwQgBxZBQmbdCgF7Ooy6rYlXZBR6r/rgWB9n3RP8emDCwfCMul9HOMT432oKNbhW
bGrcMu9AWv/pgzXogxSzYbEdTAnoVEODtU1suCa8LV6KJPEG693gARnRm/KjvPHa
FfsK
=39IY
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2022.04-b' of https://source.denx.de/u-boot/custodians/u-boot-at91
Second set of u-boot-at91 features for the 2022.04 cycle:
This small feature set includes few changes for sama7g5 and sama7g5ek:
turn blue led on at boot, changes required for the Rev4 of the board,
better sync with the Linux DT with regards to the new DT nodes.
The am335x-ice-v2 board's Ethernet ports can be configured
in 'MII' or 'RMII' mode to be connected to 'PRUSS' or 'CPSW'
Ethernet subsystems.
This patch sets the environment variable 'ice_mii' to
'mii' or 'rmii' accordingly. Based on that we choose the
appropriate board devicetree i.e. 'am335x-ice-v2.dtb' or
'am335x-ice-v2-prueth.dtb'.
Since there are 2 Ethernet ports with 2 modes, there can be 4
configurations but for now we consider both ports in different modes
to be an invalid configuration and prevent boot in that case.
Signed-off-by: Roger Quadros <rogerq@ti.com>
[Amjad: use overlay instead of using new am335x-ice-v2-prueth.dtb]
Signed-off-by: Amjad Ouled-Ameur <aouledameur@baylibre.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Make prueth_is_mii be marked __maybe_unused]
Signed-off-by: Tom Rini <trini@konsulko.com>
Call dram_init_banksize() from spl_board_init() otherwise TFTP download
fails due to lmb_get_free_size() not able to find unreserved region due
to lack of DRAM size info. Required to support Ethernet boot on AM64x.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
I got an
<dirk.eibach@gdsys.cc>: host mxlb.ispgateway.de[80.67.18.126] said:
554 Sorry, no mailbox here by that name. (in reply to RCPT TO command)
when sending e-mail to dirk.eibach@gdsys.cc.
Drop Dirk Eibach from MAINTAINERS of board/gdsys/a38x and
board/gdsys/mpc8308. The latter would be left maintainerless, add
Mario Six <mario.six@gdsys.cc> (he is also maintainer of the former
board).
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
A385 controlcenterdc board does not use PCI DM properly and touches some
PCIe devices directly in its board code.
This controlcenterdc spl_board_init() function expects that PCIe link is
already initialized. Link itself is initialized in a38x serdes code but
this will change in future and link initialization will be postponed from
U-Boot SPL to proper U-Boot.
So explicitly enable PCIe link 2 in spl_board_init() function via
SoC Control Register 1 to not break this code by future changes. This board
has PCIe link 2 just x1, so no additional initialization (except enabling
PCIe port) is needed.
Signed-off-by: Pali Rohár <pali@kernel.org>
The only user of board_pex_config() weak function is A385 controlcenterdc
board. It looks like that code in its board_pex_config() function needs to
be executed after PCIe link is up. Therefore put this code into
spl_board_init() function which is called after a38x serdes initialization,
and therefore it is after the serdes hws_pex_config() function finishes
(which is the state before this change).
With this change completely remove board_pex_config() function as it is not
used anymore.
Signed-off-by: Pali Rohár <pali@kernel.org>
a7y17lte is called SM-A720F, and a3y17lte SM-A320F. a3y17lte also
should select PINCTRL_EXYNOS78x0, not the (non-existent)
PINCTRL_EXYNOS7880, and it has an Exynos 7870 SoC and not 7880.
Fixes: 3e2095e960 ("board: samsung: add support for Galaxy A series
of 2017 (a5y17lte)")
Signed-off-by: Henrik Grimler <henrik@grimler.se>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Macro XR3PCI_ECAM_OFFSET is unused and in case it would be needed in future
it can be replaced by standard PCIE_ECAM_OFFSET macro from pci.h file.
Signed-off-by: Pali Rohár <pali@kernel.org>
- meson64_android: add board specific env settings, in order to support VIM3/L for android
- add changes to support VIM3/L android boot by using meson64_android.h config
-----BEGIN PGP SIGNATURE-----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=dLEg
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20220107' of https://source.denx.de/u-boot/custodians/u-boot-amlogic into next
- disable CONFIG_NET_RANDOM_ETHADDR when unnecessary on amlogic based configs
- meson64_android: add board specific env settings, in order to support VIM3/L for android
- add changes to support VIM3/L android boot by using meson64_android.h config
Currently, imx6q udoo board fails to boot like this:
U-Boot SPL 2022.01-rc3-00061-g95ca715adad3 (Dec 18 2021 - 18:04:40 -0300)
Trying to boot from MMC1
The reason is that the eSDHC controller is not initialized in SPL.
Initialize the eSDHC controller in SPL via C code as DM is not
used in SPL.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Use binman to pack images.
Note that imx8mm_venice supports several boards via multiple DTB's thus
in the fit node we must use:
- fit,fdt-list = "of-list"
- fdt-SEQ
- config-SEQ
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
After all these board switch to binman, we could use common imximage.cfg
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Patrick Wildt <patrick@blueri.se>
Somewhere along the line, the board stopped being able to boot.
Rather than just fixing the issue, let's fix the issue and migrate
to binman to eliminate a warning when using custom imx tools for
generating the binary.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
To eliminate a warning when using custom imx tools for generating
a binary, use binman to generate flash.bin.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
By default the Model information from DT is printed:
CPU: Freescale i.MX6SX rev1.2 996 MHz (running at 792 MHz)
CPU: Extended Commercial temperature grade (-20C to 105C) at 63C
Reset cause: POR
Model: UDOO Neo Basic
Board: UDOO Neo FULL
I2C: ready
As the udoo basic DT is used, such output may be confusing.
Improve it by only printing the Board model instead, which is
read from the board identification GPIOs.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Tommaso Merciai <tomm.merciai@gmail.com>
Tested-by: Tommaso Merciai <tomm.merciai@gmail.com>
Currently, the board model is not printed correctly:
Board: UDOO Neo UNDEFINED
Read the model type in SPL and store it the internal OCRAM, so that
U-Boot proper can retrieve it correctly.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
The ethernet has a RMII not RGMII, also needs DM_MDIO and finally
initialise it later in the process as it's not needed that early on
and not everything is ready so it locks up the device.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
This fixes booting from the mSD card from both SPL and when
using it for the OS booting. It also cleans up a few mmc
booting bits that are no longer needed.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
When using QEMU to have a quick test of booting U-Boot S-mode payload
directly without the needs of preparing the SPI flash or SD card images
for SiFive Unleashed board, as per the instructions [1], it currently
does not boot any more.
This was caused by the OF_PRIOR_STAGE removal, as gd->fdt_blob no longer
points to a valid DTB. OF_BOARD is supposed to replace OF_PRIOR_STAGE,
hence we need to add the OF_BOARD logic in board_fdt_blob_setup().
[1] https://qemu.readthedocs.io/en/latest/system/riscv/sifive_u.html#running-u-boot
Fixes: 2e8d2f8843 ("riscv: Remove OF_PRIOR_STAGE from RISC-V boards")
Fixes: d6f8ab30a2 ("treewide: Remove OF_PRIOR_STAGE")
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Philipp does not work at Theobroma Systems anymore so let's swap
Philipp's address with mine.
Cc: Philipp Tomsich <philipp.tomsich@vrull.eu>
Cc: Quentin Schulz <foss+u-boot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@vrull.eu>
In AOSP, both VIM3 and VIM3L have 2 bootloader flavors,
depending on A/B enablement.
For example, for vim3l, the naming is:
- u-boot_kvim3l_noab.bin : legacy support
- u-boot_kvim3l_ab.bin : A/B support
Prepare a defconfig to support u-boot_kvim3_ab.bin and
u-boot_kvim3l_ab.bin.
This is identical to khadas-vim3{l}_ab_android but will be updated in
the next commit.
Also update partitioning tables for A/B support.
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20211122152207.219023-4-mkorpershoek@baylibre.com
The system fails to boot without any environment location, so return
ENVL_NOWHERE when there's nowhere to store the environment instead
of ENVL_UNKNOWN.
The same change was also done by commit 50918d0df5 ("xilinx: Return
ENVL_NOWHERE instead of ENVL_UNKNOWN") for zynq and zynqmp.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/e4ed36408f10159677ed8060bfd5289f3e0691fa.1637752614.git.michal.simek@xilinx.com
The xilinx board_fdt_blob_setup() implementation makes use of
XILINX_OF_BOARD_DTB_ADDR, but no default value is currently defined for
microblaze. Add one so that microblaze could also work with
CONFIG_OF_SEPARATE.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Link: https://lore.kernel.org/r/20211202195657.246723-1-ovidiu.panait@windriver.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
MicroBlaze vector base address is configurable (hdl C_BASE_VECTORS
configuration parameter). Current code assumes that the reset vector
location is always 0x0.
Add the XILINX_MICROBLAZE0_VECTOR_BASE_ADDR Kconfig option so the user
can adjust the reset vector address.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Link: https://lore.kernel.org/r/20211130163358.2531677-8-ovidiu.panait@windriver.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Migrate CONFIG_SYS_USR_EXCEP to Kconfig. Also, rename it to
XILINX_MICROBLAZE0_USR_EXCEP in order to match the naming convention of
microblaze-generic Kconfig options.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Link: https://lore.kernel.org/r/20211130163358.2531677-7-ovidiu.panait@windriver.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Previous psu init was targeting SOM + KV260 carrier card and also contain
configurations for other devices on carrier card. This config is removing
all expected configurations for CC and let U-Boot to handle all of it self.
This configuration is designed for SOM itself (and I would bet without
eMMC).
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/5782131058dc372befd3fdb4dceabeea5ba56606.1637236693.git.michal.simek@xilinx.com
The SMSC driver is using the old driver model.
Init the virtio system in vexpress64.c so that the network device is
discovered.
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Capture x0 in lowlevel_init.S as potential fdt address. Modify
board_fdt_blob_setup to use fdt address from either vexpress_aemv8.h
or lowlevel_init.S.
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Rename from vexpress_aemv8a.h -> vepxress_aemv8.h as new FVPs may not be
v8-A. No change in behavior.
This is towards future work to enable support for the FVP_BaseR.
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
- support for showing a logo without splash screen config
- support for BMP drawing to depths other than 16bpp
- tests for the different types of supported BMP images
- support showing a logo when running coreboot via qemu
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCYcsdCQ4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXCLhAJ9pLJE3SpQRzpm+Nu4EMbCDzZKr+wCfbxnAZ9LC
zS1XZ6u9Se4ysDb+PYs=
=Hf5j
-----END PGP SIGNATURE-----
Merge tag 'video-next-20211228' of https://source.denx.de/u-boot/custodians/u-boot-video into next
- various fixes to the sandbox display support
- support for showing a logo without splash screen config
- support for BMP drawing to depths other than 16bpp
- tests for the different types of supported BMP images
- support showing a logo when running coreboot via qemu
This converts the following to Kconfig:
CONFIG_88F5182
CONFIG_BOARD_IS_OPENRD_BASE
CONFIG_BOARD_IS_OPENRD_CLIENT
CONFIG_BOARD_IS_OPENRD_ULTIMATE
CONFIG_D2NET_V2
CONFIG_FEROCEON
CONFIG_FEROCEON_88FR131
CONFIG_INETSPACE_V2
CONFIG_KW88F6192
CONFIG_KW88F6281
CONFIG_KW88F6702
CONFIG_NET2BIG_V2
CONFIG_NETSPACE_LITE_V2
CONFIG_NETSPACE_MAX_V2
CONFIG_NETSPACE_MINI_V2
CONFIG_NETSPACE_V2
CONFIG_SHEEVA_88SV131
At this point mv-plug-common.h is now only an include of mv-common.h so
remove that indirection.
Signed-off-by: Tom Rini <trini@konsulko.com>
In order to finish moving this symbol to Kconfig for all platforms, we
need to do a few more things. First, for all platforms that define this
to a function, introduce CONFIG_DYNAMIC_SYS_CLK_FREQ, similar to
CONFIG_DYNAMIC_DDR_CLK_FREQ and populate clock_legacy.h. This entails
also switching all users from CONFIG_SYS_CLK_FREQ to get_board_sys_clk()
and updating a few preprocessor tests.
With that done, all platforms that define a value here can be converted
to Kconfig, and a fall-back of zero is sufficiently safe to use (and
what is used today in cases where code may or may not have this
available). Make sure that code which calls this function includes
<clock_legacy.h> to get the prototype.
Signed-off-by: Tom Rini <trini@konsulko.com>
This CONFIG option is used in one of two ways. The first way is that it
is defined to a static value, of an unsigned long size. The second way
is that it is defined to something, typically a function, to determine
this value at run time.
However, in a few cases that function returns a static value. Change
that to using the static value directly.
In the case of using something at run time, convert everything to using
a function of the same name and prototype. This will allow for further
cleanups.
Finally, we have a few cases where the function is just not used, so
drop it.
Signed-off-by: Tom Rini <trini@konsulko.com>
When we have CONFIG_DYNAMIC_DDR_CLK_FREQ set is the only time we should
have this function, so guard it so that we can include <clock_legacy.h>
in this file later on.
Signed-off-by: Tom Rini <trini@konsulko.com>
When we have CONFIG_DYNAMIC_DDR_CLK_FREQ set is the only time we should
have this function, so guard it so that we can include <clock_legacy.h>
in this file later on.
Signed-off-by: Tom Rini <trini@konsulko.com>
In the case of CONFIG_SYS_FDT_ADDR this was being used to modify the
default value of fdt_addr / fdt_addr_r, which is not something to expose
in this manner and is not otherwise done. The case of SYS_ENV_ADDR is
similar but only done on the pic32mzdask platform, for scriptaddr.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_VID
CONFIG_VOL_MONITOR_INA220
CONFIG_VOL_MONITOR_IR36021_READ
CONFIG_VOL_MONITOR_IR36021_SET
CONFIG_VOL_MONITOR_LTC3882_READ
CONFIG_VOL_MONITOR_LTC3882_SET
To finish this migration, we first need to introduce CONFIG_SPL_VID as
some platforms only use this code in full U-Boot while others use it in
SPL as well. To make the Kconfig logic clearer, guard all of the
sub-options with a if VID || SPL_VID check. Finally, add Kconfig
options for the remaining related options that did not previously have
one.
Signed-off-by: Tom Rini <trini@konsulko.com>
Because of how these symbols work, and the remaining board config.h file
uses, we need to do these at the same time. In some cases we just get
to move rather directly to the defconfigs. A few cases require manual
intervention.
For the case of the eb_cpu5282 we need to select HW_WATCHDOG for the
target, given how it's implemented.
For the cases of m53menlo, dh_imx6, display5, and display5_factory we
disable SPL watchdog support as the particular combination of options
they want would require either more symbols or enabling SPL_DM.
Signed-off-by: Tom Rini <trini@konsulko.com>
This option is used as part of configuring the default environment for a
number of platforms. However, it is always set to 1 and the only time
it is part of Kconfig, it is used in a hard-coded manner. Hard-code the
value in the environment instead.
Signed-off-by: Tom Rini <trini@konsulko.com>
PX30.Core is an EDIMM SOM based on Rockchip PX30 from Engicam.
C.TOUCH 2.0 is a general purpose carrier board with capacitive
touch interface support.
10.1" OF is a capacitive touch 10.1" Open Frame panel solutions.
PX30.Core needs to mount on top of C.TOUCH 2.0 carrier with pluged
10.1" OF for creating complete PX30.Core C.TOUCH 2.0 10.1" Open Frame.
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Long gone is the time a custom TF-A was needed for Puma, upstream TF-A
works just fine now.
The flashing instructions are updated to match how newer rkdeveloptool
and rkbin work.
Finally, rkbin provides a way to flash SPI via USB OTG interface so
let's document that.
Cc: Quentin Schulz <foss+u-boot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Use this new Kconfig instead of OF_BOARD, so we know for sure which boards
obtain their devicetree from a prior stage. Leave sandbox alone since it
does not. Also don't touch xilinx_versal_virt since it does not have a
specific TARGET Kconfig.
This option implies OF_BOARD for now, but with future work standard
passage may be used instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Add rpi_4_32b and rpi_arm64 to the list of boards converted]
Signed-off-by: Tom Rini <trini@konsulko.com>
Move Turris MOX specific remove_disabled_nodes() to fdt_support with
name fdt_delete_disabled_nodes(), so that others can potentially use it.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
The pre-relocation board topology reading in board_fix_fdt() is
unstable: sometimes wrong data are read from the SPI bus.
This is due to wrong order of SPI bus configuration instructions: we
first need to set the pins to SPI mode, and only after that configure
the bus.
Also add a 1ms delay before enabling chip-select, so that the clock pin
is high for some time before reading the bus.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Enable eth1 node in U-Boot's device-tree if a network module (SFP, Topaz
or Peridot) is detected.
This is required for proper detection of eth1 comphy in a3700 comphy
driver by the following patches.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
It is better to find DT nodes by compatible strings or aliases instead
of path.
There were issues with Linux some DTBs having different names of some
nodes, e.g.
internal-regs
instead of
internal-regs@d0000000
This should be a generic fix for such issues.
Also since fdt_support now contains needed functions, we can drop our
own implementations.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Since no one uses this feature and I am not aware of any parsers of this
in Linux, remove it.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Pratyush Yadav <p.yadav@ti.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Michael Walle <michael@walle.cc>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Commit f0921f5098 ("fdt: Sync up to the latest libfdt") introduced
fdt_generate_phandle() in libfdt, making fdt_alloc_phandle() obsolete in
fdt_support.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: "hui.song" <hui.song_1@nxp.com>
Cc: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Replace fdt_alloc_phandle() with subsequent fdt_set_phandle() by
fdt_create_phandle().
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Vladimir Oltean <vladimir.oltean@nxp.com>
No functional change intended. This patch switches from the legacy I2C
API to the DM I2C API, so that this code can be used with DM I2C
enabled.
Signed-off-by: Stefan Roese <sr@denx.de>
The variables retaining the strap values have to be initialized, always,
make it so. Moreover, free the requested GPIO list at the end to avoid
wasting memory.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The rzg2_beacon_defconfig creates an image for RZ/G2[MNH] and
as such creates three different device trees and each of them
have a corresponding -u-boot.dtsi file which are basically
copies of each other. Create a common include file to be
referenced by each of the respective board-u-boot.dtsi files
to reduce duplicate code and simplify support going forward.
This also restores some lost functionality from the device
tree re-sync and updates the MAINTAINER file to include all
beacon-renesom device tree files.
Signed-off-by: Adam Ford <aford173@gmail.com>
The sunxi MUSB glue driver has some code to check for external VBUS
presence when it's going to use the MUSB host mode, and it warns if
there is VBUS provided through the cable (in sunxi_musb_enable()).
This code was apparently copied to the USB gadget detection code
(g_dnl_board_usb_cable_connected()), but here we actually *expect*
external VBUS power, so a warning is wrong and confusing.
So far this message rarely triggered, but a recent patch (6fa41cdd19)
changed this:
===========================
=> ums 0 mmc 2
UMS: LUN 0, dev mmc 2, hwpart 0, sector 0x0, count 0xe90000
A charger is plugged into the OTG
/A charger is plugged into the OTG
\A charger is plugged into the OTG
|A charger is plugged into the OTG
-A charger is plugged into the OTG
....
===========================
Remove the message for the gadget cable detection call, and just return
the status of the VBUS detection, as this is what the callers are after.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Enable saving environment to SPI flash memory on SiFive
Unmatched.
Signed-off-by: Thomas Skibo <thomas-git@skibo.net>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Configure SPI flash devices into SPL. Add SPI boot option to spl.c.
Document how to format flash for booting.
Signed-off-by: Thomas Skibo <thomas-git@skibo.net>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
This patch updates Microchip MPFS Icicle Kit support. For now,
add Microchip I2C driver, set environment variables for
mac addresses and default build for SBI_V02.
Signed-off-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Load NetXtreme firmware in board_init when BNXT_ETH is selected.
Signed-off-by: Bharat Gooty <bharat.gooty@broadcom.com>
Signed-off-by: Roman Bacik <roman.bacik@broadcom.com>
Add support of mtd backend for nor1 when this device is present on the
board, on STM32MP157C-EV1 for example, as the support of several MTD
spi-nor instance are now supported with commit b7f060565e ("mtd:
spi-nor: allow registering multiple MTDs when DM is enabled").
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Enable an existing simple framebuffer node in the Linux kernel device
tree and the add the associated reserved memory node to preserved the
resources (clock, memory) used by the stm32 video driver to display
the splashscreen = background in exlinux.conf file.
These resources will be released by the Linux driver only when the
associated driver is ready to avoid transition issues during the Linux
kernel initialization between U-Boot splash screen and the final display.
See Linux documentation for details:
Documentation/devicetree/bindings/display/simple-framebuffer.yaml
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Rename the function named lcd_dt_simplefb* to fdt_simplefb* to be aligned
with the associated file name fdt_simplefb.h/fdt_simplefb.c
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
The variables retaining the strap values have to be initialized, always,
make it so. Moreover, free the requested GPIO list at the end to avoid
wasting memory.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The Raspberry Pi Foundation released the new Zero 2 W which we
want to detect, so we can detect the correct device tree file name.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
The Raspberry Pi Foundation has updated their documentation so update
the URL to the latest place to find the HW device revision codes.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Commit aeb0ca64db ("arm: mvebu: turris_omnia: disable MCU watchdog in
SPL when booting over UART") disabled MCU watchdog when booting over
UART to ensure that watchdog does not reboot the board before UART
transfer finishes.
But if UART transfer fails for some reason, or if U-Boot binary crashes,
then board hangs forever as there is no watchdog running which could
reset it.
To fix this issue, enable A385 watchdog with very high timeout before
disabling MCU watchdog to ensure that even slow transfer can finish
successfully before watchdog timer expires and also to ensure that if
board hangs for some reason, watchdog will reset it.
Omnia's MCU watchdog has fixed 120 seconds timer and it cannot be
changed (without updating MCU firmware). A385 watchdog by default uses
25 MHz input clock and so the largest timeout value (2^32-1) can be
just 171 seconds. But A385 watchdog can be switched to use NBCLK (L2) as
input clock (on Turris Omnia it is 800 MHz clock) and in this case final
watchdog clock frequency is calculated as:
freq = NBCLK / 2 / (2 ^ R)
So A385 watchdog on Turris Omnia can be configured to at most 1374
seconds (about 22 minutes). We set it to 10 minutes, which should be
enough even for bigger U-Boot binaries or slower UART transfers.
Both U-Boot and Linux kernel, when initializing A385 watchdog, switch
watchdog timer to 25 MHz input clock, so usage of NBCLK input clock in
U-Boot SPL does not cause any issues.
Fixes: aeb0ca64db ("arm: mvebu: turris_omnia: disable MCU watchdog in SPL when booting over UART")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
The common emulation Makefile has a dependency on a non-existent
qemu_capsule.o when building with support for capsule update enabled
(CONFIG_EFI_RUNTIME_UPDATE_CAPSULE=y).
The code which was in qemu_capsule.c has been completely moved to
lib/efi_loader/efi_capsule.c by commit 7a6fb28c8e ("efi_loader: capsule:
add back efi_get_public_key_data()").
Remove the false dependency.
This fixes the following build error:
make[1]: *** No rule to make target 'board/emulation/common/qemu_capsule.o', needed by 'board/emulation/common/built-in.o'. Stop.
Fixes: commit 47a25e81d3 ("Revert "efi_capsule: Move signature from DTB to .rodata"")
Signed-off-by: Vincent Stehlé <vincent.stehle@arm.com>
Cc: Simon Glass <sjg@chromium.org>
Without default setting of gd->env_addr, U-Boot will cause
a synchronous abort if the env-variables on the SPI flash is
broken or not saved corectly. Set gd->env_addr correctly.
This reverts commit 535870f3b0.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
These conflict with real-word addresses. Use locally administered
MAC addresses and a suitable IPv4 address from 192.0.2.0/24
(TEST-NET-1).
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Alexander Dahl <ada@thorsis.com>
Use a text file for the environment instead of the #define settings.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
sdhci:
- Fix emmc mini case with missing firmware interface
zynqmp:
- Restore JTAG interface if required
- Allow overriding board name
- Add support for DLC21
- Fix one fallthrought statement description
- Use config macro instead of name duplication
- Save multiboot to variable
firmware:
- Handle ipi_req errors better
- Use local buffer in case user doesn't need it instead of NULL/0 location
spi:
- gqsi: Fix write issue at low frequencies
net:
- gem: Disable broadcasts
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYZPDrwAKCRDKSWXLKUoM
IS9GAJ93T/uprhLcKWMb+284YMb2caWgOACfZ02nTlzvZKNNXVretJgZaHXqj1M=
=cwTL
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.01-rc3' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2022.01-rc3
sdhci:
- Fix emmc mini case with missing firmware interface
zynqmp:
- Restore JTAG interface if required
- Allow overriding board name
- Add support for DLC21
- Fix one fallthrought statement description
- Use config macro instead of name duplication
- Save multiboot to variable
firmware:
- Handle ipi_req errors better
- Use local buffer in case user doesn't need it instead of NULL/0 location
spi:
- gqsi: Fix write issue at low frequencies
net:
- gem: Disable broadcasts
The subdivision name "TQ Components" hasn't been in use for a long time.
Rename the vendor directory to "tq", which also matches our Device Tree
vendor prefix.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Config check should be done without the SPL_ prefix.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Link: https://lore.kernel.org/r/20211104192802.3093811-1-ricardo@foundries.io
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
We need to filter out NET_ETH_START errors because we have to enable
networking in order to propagate the MAC addresses to the DT while there
is no network driver for the prueth in U-Boot yet.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
- device-tree sync-up with Linux for ls1028a
- fixes/update in fsl-ddr driver, fsl-validate, lx2162a, fsl-mc,
spintable code, configs, qspi node, pci
- enable EFI_SET_TIME support in sl28
- powerpc: Drop -mstring
- Remove nWP GPIO hog
- Increase SF bus frequency to 50Mhz and enable SFDP
- Disable video output for DHSOM
- Disable EFI
- Enable DFU_MTD support
- Create include file for STM32 gpio driver private data
- Split board and SOC STM32MP15 configuration
- Device tree alignement with v5.15-rc6 for STM32MP15
- Add binman support for STM32MP15x
- Normalise newlines for stm32prog
- Update OTP shadow registers in SPL
-----BEGIN PGP SIGNATURE-----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=lqEG
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20211110' of https://source.denx.de/u-boot/custodians/u-boot-stm
- DHSOM update:
- Remove nWP GPIO hog
- Increase SF bus frequency to 50Mhz and enable SFDP
- Disable video output for DHSOM
- Disable EFI
- Enable DFU_MTD support
- Create include file for STM32 gpio driver private data
- Split board and SOC STM32MP15 configuration
- Device tree alignement with v5.15-rc6 for STM32MP15
- Add binman support for STM32MP15x
- Normalise newlines for stm32prog
- Update OTP shadow registers in SPL
In some part of STM32MP15 support the CONFIG_TFABOOT can be replaced
by other config: CONFIG_ARMV7_PSCI and CONFIG_ARM_SMCCC.
This patch also simplifies the code in cpu.c, stm32mp1_ram.c and
clk_stml32mp1.c as execution of U-Boot in sysram (boot without SPL and
without TFA) is not supported: the associated initialization code is
present only in SPL.
This cleanup patch is a preliminary step to support SPL load of OP-TEE
in secure world, with SPL in secure world and U-Boot in no-secure world.
Reported-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The DHSOM uses different SPI NOR layout than the ST devkit, stop
pulling in the ST specific runtime mtdparts settings and adjust
the mtdparts accordingly.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The stm32 gpio driver private data are not needed in arch include files,
they are not used by code except for stm32 gpio and pincontrol drivers,
using the same IP; the defines for this IP is moved in a new file
"stm32_gpio_priv.h" in driver/gpio.
This patch avoids to have duplicated file gpio.h for each SOC
in MPU directory mach-stm32mp and in each MCU directory arch-stm32*
and allows to remove CONFIG_GPIO_EXTRA_HEADER for all STM32.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add a configuration file "stm32mp15_st_common.h" to handle the
STMicroelectronics boards configuration and rename stm32mp1.h to
"stm32mp15_common.h" to handle the generic STM32MP15x series configuration.
The configuration file "dh_stm32mp1.h" is also renamed to
"stm32mp15_dh_dhcom" for the configuration of board based on the
dhelectronics STM32MP15x SOM.
In the STMicroelectronics board configuration the default bootcmd
"bootcmd_stm32mp" is updated to only select the extlinux file found on
SD-Card on STM32MP15x EV1 for boot from NOR device.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
I'd like to keep informed about ls1028a.dtsi changes. For now, there is
no top-level entry for any layerscape specific files. Instead, add the
file entry to my board MAINTAINERS file.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Increase fdt blob size for lx2160 and lx2162 series
to fix below errors/warnings during device tree fixup.
Unable to update property /soc/spi@2100000:status, err=FDT_ERR_NOSPACE
Unable to update property /soc/spi@2110000:status, err=FDT_ERR_NOSPACE
Unable to update property /soc/spi@2120000:status, err=FDT_ERR_NOSPACE
WARNING: could not set reg FDT_ERR_NOSPACE.
WARNING unable to set iommus: FDT_ERR_NOSPACE
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Set popts->cpo_sample to 0x54 in t104xrdb/ddr.c to optimize cpo
Signed-off-by: Priyanka Singh <priyanka.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
According to ./include/linux/kconfig.h,
CONFIG_IS_ENABLED(OF_BOARD) expands to 0
when CONFIG_SPL_BUILD is defined because
there is no CONFIG_SPL_OF_BOARD.
Use #if defined instead.
Fixes: 2e8d2f8843 ("riscv: Remove OF_PRIOR_STAGE from RISC-V boards")
Signed-off-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The current EFI video driver only works when running in the stub. In that
case the stub calls boot services (before jumping to U-Boot proper) and
copies the graphics info over to the efi table. This is necessary because
the stub exits boot services before jumping to U-Boot.
The app maintains access to boot services throughout its life, so does not
need to do this. Update the driver to support calling boot services
directly.
Enable video output for the app. Note that this uses the
EFI_GRAPHICS_OUTPUT_PROTOCOL protocol, even though it mentions vesa.
A sample qemu command-line for this case is:
qemu-system-x86_64 -bios /usr/share/edk2.git/ovmf-ia32/OVMF-pure-efi.fd
-drive id=disk,file=try.img,if=none,format=raw -nic none
-device ahci,id=ahci -device ide-hd,drive=disk,bus=ahci.0
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Most modern platforms use 64-bit EFI so it is useful to have a U-Boot app
that runs under that. Add a (non-functional) build for this.
Note that --whole-archive causes the gcc 9.2 linker to crash, so disable
this for now. Once this is resolved, things should work.
For now, avoid mentioning the documentation for the 64-bit app, since it
does not work.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
- add JetHub D1 eth mac generation with manufacturer OUI
-----BEGIN PGP SIGNATURE-----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=UyL3
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20211102' of https://source.denx.de/u-boot/custodians/u-boot-amlogic
- add sm efuse write support and cmd for read/write efuse
- add JetHub D1 eth mac generation with manufacturer OUI
patman 'postfix' support
fix binman test race condition causing a timeout error
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmF+8FcRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreYP+AgApwZWYteNQu/OKwCFrZq0QIQYZwJQqe93
9CdQtpKH2boakfNcvsbPP5dXk8GNz5cEky1Whk2kIH1b11FHgklnIPFtFxzMesm8
oYET1w0iItp+4P4ZsQmVgJpynz4yUmUnMEOBNqwI2zeo7dMgx8Zw+cWz8FDo4e6K
pDKHAx9UmiCRu6h+IbsAzeMcq/HqAvFOzoWbp/LkmaWnwIjASCM4UUVoz1+UtoFU
0ENn/7vn70WOLw0JoEib8M7qy+IT7Mz42eZwDVGzYKSDlTZmXNwKLLzgJpEqW4hw
lYIEBUK3sr0q+kcKI776JeFaFhI6k71uVJcjkkUgGuF1hda1kc0Msw==
=E8s4
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-boo21' of https://source.denx.de/u-boot/custodians/u-boot-dm
Environment tidy-ups
patman 'postfix' support
fix binman test race condition causing a timeout error
# gpg: Signature made Sun 31 Oct 2021 03:36:55 PM EDT
# gpg: using RSA key B25C0022AF86A7CC1655B6277F173A3E9008ADE6
# gpg: issuer "sjg@chromium.org"
# gpg: Good signature from "Simon Glass <sjg@chromium.org>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: B25C 0022 AF86 A7CC 1655 B627 7F17 3A3E 9008 ADE6
Allow usage of the bootstage facilities in SPL.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Sometimes we use uchar and sometimes char for the default environment
array. By always using char, we can get rid of some explicit casts.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Simon Glass <sjg@chromium.org>
Various freescale boards set gd->env_addr to default_environment in
board_init(), conditional on CONFIG_ENV_IS_NOWHERE, but this is
redundant, since it is done by env_init() before board_init() is called.
Let the env subsystem handle this.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
This board sets gd->env_addr to default_environment in board_init(), but
the board has environment in SPI flash according to defconfig. Let the
env API handle environment automatically.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Samsung Galaxy A3, A5, A7 (2017) - middle class Samsung smartphones.
U-boot can be used as chain-loaded bootloader to gain control
on booting vanilla linux(and possibly others) kernels
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Samsung S9 SM-G9600 - Snapdragon SDM845 version of the phone,
for China \ Hong Kong markets.
Has unlockable bootloader, unlike SM-G960U (American market version),
which allows running u-boot as a chain-loaded bootloader.
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Stop using the device tree as a source for ad-hoc information.
This reverts commit 2ae7adc659.
Signed-off-by: Michael Walle <michael@walle.cc>
[trini: Also make board/broadcom/bcmns3/ns3.c fail clearly now]
Signed-off-by: Tom Rini <trini@konsulko.com>
Now that the three M/N/H variants can be built from one config,
rename the defconfig file to be more generic since it supports multiple
RZ/G2.
Signed-off-by: Adam Ford <aford173@gmail.com>
Now that TARGET_BEACON_RZG2M can handle all the work that
was done with TARGET_BEACON_RZG2N and TARGET_BEACON_RZG2H,
remove them since they just create more duplicate code.
Signed-off-by: Adam Ford <aford173@gmail.com>
There are three boards from Beacon, RZ/G2 M/N/H which all
use the same board file, but different device trees.
Add code to automatically select the proper device tree
based on the CPU type.
Signed-off-by: Adam Ford <aford173@gmail.com>
JetHome has own MAC OUI. Add jethub-j100 board file. Update config.
Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Fix issue reported by checkpatch.pl
WARNING: Possible comma where semicolon could be used
#499: FILE: board/xilinx/zynqmp/zynqmp.c:499:
+ size = ALIGN(CONFIG_SYS_MALLOC_LEN + total_size, MMU_SECTION_SIZE),
+ reg = lmb_alloc(&lmb, size, MMU_SECTION_SIZE);
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/ef264451ef9455ada9784bedbc91f74b94b8a237.1634799528.git.michal.simek@xilinx.com
- mvebu: Fix usage of BIN header arguments (Pali)
- mvebu: turris_omnia: Fix MTD partitions order for Linux (Pali)
- mvebu: nandpagesize support for kwbimage v1 (Pali)
Linux enumerates MTD partitions in DTB order, while the fdt_add_subnode()
function puts a new subnode at the beginning.
To fix this, put MTD partitions into DTB in reverse order.
Fixes: 92f36c8e74 ("arm: mvebu: turris_omnia: fixup MTD partitions in Linux' DTB")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
OF_HOSTFILE is used on sandbox configs only. Although it's pretty
unique and not causing any confusions, we are better of having simpler
config options for the DTB.
So let's replace that with the existing OF_BOARD. U-Boot would then
have only three config options for the DTB origin.
- OF_SEPARATE, build separately from U-Boot
- OF_BOARD, board specific way of providing the DTB
- OF_EMBED embedded in the u-boot binary(should not be used in production
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
On the iMX7ULP uCOM board, OP-TEE uses the memory region defined by the
maximum DRAM address minus CONFIG_OPTEE_TZDRAM_SIZE, so subtract
CONFIG_OPTEE_TZDRAM_SIZE from the available DRAM size to avoid
conflicts.
Note the OPTEE boot process itself subtracts the DRAM region it
lives in from the memory map passed to Linux.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Since we uses the DTS and PHY reset gpio in EQoS driver to do the
reset, remove the duplicated codes from board file.
Signed-off-by: Ye Li <ye.li@nxp.com>
When boot.bin is configured for secure boot the CSU will disable the
JTAG interface on all cases.
Some boards might rely on this interface for flashing to QSPI in which
case those systems might end up bricked during development.
This commit will restore the interface under CSU control
Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Link: https://lore.kernel.org/r/20211013134800.19452-1-jorge@foundries.io
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
We are printing board information in checkboard() function, which is
called from the default weak implementation of show_board_info().
Rename checkboard() to show_board_info(). This throws away the weak
implementation of show_board_info().
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Currently we always overwrite ethaddrs with those from EEPROM.
In order to allow user to use a cloned MAC address in U-Boot, change the
code so that it sets ethaddr variables only if they aren't set or are
invalid.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Currently we overwrite ethaddr and eth1addr only if these variables
don't exist.
Better overwrite them even if the env variable exists, but is invalid -
eth_env_get_enetaddr_by_index() checks for validity.
Refactor the code to use a for cycle.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Handle reset button even if we can't configure modules.
This happens if we fail retrieving reset GPIO with which we can reset
the modules.
(Note that this GPIO is different from reset button GPIO.)
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
We are printing board information in last_stage_init(), but U-Boot has
dedicated function, show_board_info(), for this.
Move code which prints board information (board version, serial number,
module topology, ...) to show_board_info().
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Add code to build the eMMC variant of the Colibri iMX6ULL, i.e. the
'Colibri iMX6ULL 1GB' which has a eMMC instead of the raw NAND used
on other SKUs.
Related-to: ELB-4056, ELB-4057
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Integrate new Toradex SKU 0062 Colibri iMX6ULL 1GB IT. This commit
basically adjusts three parameters of the RAM settings:
Increase density from 4Gb to 8Gb
Increase ROW address from 15 to 16
Increase tRFC (refresh command time) from 260 to 350
This timing is valid for all Toradex Colibri iMX6ULL SKUs
Related-to: ELB-4055, ELB-4057
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Add new i.MX 6ULL and 8M Plus SKUs to ConfigBlock handling:
0062: Colibri iMX6ULL 1GB IT (eMMC)
0063: Verdin iMX8M Plus Quad 4GB IT
0064: Verdin iMX8M Plus Quad 2GB Wi-Fi / BT IT
0065: Verdin iMX8M Plus QuadLite 1GB IT
0066: Verdin iMX8M Plus Quad 8GB Wi-Fi / BT
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Restore "Is the module an IT version? [y/N]" for "cfgblock create"
interactive mode command, which was leading to invalid detection
of 0051 Colibri iMX8DX 1GB WB module;
Fixes: a5b5ad4d85 ("toradex: tdx-cfg-clock: add new i.mx 8m mini/plus skus")
Related-to: ELB-3482
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Also take over maintainership of remaining Toradex SoMs as Oleksandr
has left our company.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
CC: Oleksandr Suvorov <cryosay@gmail.com>
After the conversion to binman in commit 8996e6b7c6 ("imx8mm_evk: switch
to use binman to pack images"), it is necessary to flash both flash.bin and
u-boot.itb to get a bootable system. Prior to this commit, only flash.bin
was needed.
Such new requirement breaks existing distro mechanisms to generate the
final binary because the extra u-boot.itb is now required.
Generate a final flash.bin that can be used again as a single
bootable binary to keep the original behavior.
After this change the SPL binary is called spl.bin, which is a more
descriptive name for its purpose, and can still be used standalone
(for example, for secure boot purposes).
Also update imx8mm_evk.rst to remove the u-boot.itb copy step.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Heiko Thiery <heiko.thiery@gmail.com>
NXP used to setup the gpmi clock root from gpmi_clk in early versions
in their downstream BSP. [1]
However on mainline the gpmi clock root was always setup from enfc
since the beginning of the i.MX 6 series SoCs, which is still the same
today. [2]
NXP followed the mainline approach at some point and changed
setup_gpmi_io_clk to setup gpmi clock root from enfc which left faulty
code behind in our board file. [3]
This commit follows the change of NXP as it improves the performance of
the NAND from ~1.2 MiB/s to ~12 MiB/s. [3]
This change was verified to work in recovery-mode and u-boot loaded
from NAND on all four Colibri iMX6ULL SKUs from Toradex.
The frequency used to read the NAND, measured on RE# (Read Enable):
before this patch: 1.4 MHz
after this patch: 22 MHz
in Linux Kernel: 50 MHz
[1] https://source.codeaurora.org/external/imx/uboot-imx/tree/arch/arm/cpu/armv7/mx6/clock.c?h=nxp/imx_v2016.03_4.1.15_2.0.0_ga#n62
[2] commit 23608e23fd ("i.mx: add the initial support for freescale i.MX6Q processor")
[3] https://source.codeaurora.org/external/imx/uboot-imx/commit/?id=7a82a19ceabfb04bbc1591a67c99751748781c7d
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
We drop support for Verdin iMX8M Mini V1.0B.
Related-to: ELB-3551
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Turns out Microship (formerly Micrel) meanwhile integrated proper
support for the DLL setup on their KSZ9131. Unfortunately, this
conflicts with our previous board code doing that.
Fix this by getting rid of our board code and just relying on the
generic implementation relying on rgmii-id being used as phy-mode.
Fixes: commit c6df0e2ffd
("net: phy: micrel: add support for DLL setup on ksz9131")
Fixes: commit af2d3c91d8
("ARM: dts: imx8mm-verdin: Set PHY mode to RGMII-ID")
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The following warning is seen in unleashed.c in a 32-bit build:
warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Cast with uintptr_t.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Commit 47d73ba4f4 ("board: sifive: overwrite board_fdt_blob_setup in u-boot proper")
added a board-specific implementation of board_fdt_blob_setup() which
takes a pointer as the return value, but it does not return anything
if CONFIG_OF_SEPARATE is not enabled. This will cause a build warning
seen when testing booting S-mode U-Boot directly from QEMU, per the
instructions in [1]:
board/sifive/unleashed/unleashed.c: In function ‘board_fdt_blob_setup’:
board/sifive/unleashed/unleashed.c:125:1: warning: control reaches end of non-void function [-Wreturn-type]
Return &_end as the default case.
[1] https://qemu.readthedocs.io/en/latest/system/riscv/sifive_u.html#running-u-boot
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Rick Chen <rick@andestech.com>
