All partitions are created by fixup_mtd_partitions() function, so they do
not have to exist just for their removal need.
Fixes: 92f36c8e74 ("arm: mvebu: turris_omnia: fixup MTD partitions in Linux' DTB")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Marek Behún <kabel@kernel.org>
New Turris Omnia HW board revision requires that software controls
peripheral reset signals, namely PERST# signals on mPCIe slots, ethernet
phy reset and lan switch reset. Those pins are connected to MCU controlled
by MCU i2c API as GPIOs. On new HW board revision those pins stay in reset
after board reset and software has to release these peripherals from reset
manually. MCU announce this requirement by FEAT_PERIPH_MCU bit in
CMD_GET_FEATURES command.
On older HW board revisions when FEAT_PERIPH_MCU is not announced, all
those reset signals are automatically released after board finish reset.
Detect FEAT_PERIPH_MCU bit in board_fix_fdt() and ft_board_setup()
functions and insert into device tree blob pcie "reset-gpios" and eth phy
"phy-reset-gpios" properties with corresponding MCU gpio definitions.
PCIe and eth PHY drivers then automatically release resets during device
initialization. Both U-Boot and Linux kernel drivers support those device
tree reset properties.
Initialization of lan switch on new HW board revision is more complicated.
Switch strapping pins are shared with switch RGMII pins. And strapping pins
must be in specific configuration after releasing switch reset. Due to pin
sharing, it is first required to switch A385 side of switch pins into GPIO
mode, set strapping configuration, release switch from reset and after that
switch A385 pins back to RGMII mode.
Because this complicated setup is not supported by switch DSA drivers and
cannot be expressed easily in device tree, implement it manually in SPL
function spl_board_init(). So in proper U-Boot and OS/kernel would be lan
switch initialized and be in same configuration like it was on old HW board
revisions (where reset sequence did those steps at hardware level).
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Marek Behún <kabel@kernel.org>
Different Turris Omnia HW board revisions contains different MCU.
Show type in show_board_info() to easily identify which MCU is populated.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Marek Behún <kabel@kernel.org>
A large number of files include <flash.h> as it used to be how various
SPI flash related functions were found, or for other reasons entirely.
In order to migrate some further CONFIG symbols to Kconfig we need to
not include flash.h in cases where we don't have a NOR flash of some
sort enabled. Furthermore, in cases where we are in common code and it
doesn't make sense to try and further refactor the code itself in to new
files we need to guard this inclusion.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_FLASH_ERASE_TOUT
CONFIG_SYS_FLASH_LOCK_TOUT
CONFIG_SYS_FLASH_UNLOCK_TOUT
CONFIG_SYS_FLASH_WRITE_TOUT
In practice, for two m68k platforms we move to hard-coding with a
comment the timeout values, rather than try and make convoluted Kconfig
logic. We add options for the write and erase options to the pic32
flash driver, as this driver does make use of them. Everywhere else
these are unreferenced values.
Signed-off-by: Tom Rini <trini@konsulko.com>
All platforms today define CONFIG_SYS_DDR_RAW_TIMING, so drop the code
for this option being unset.
Cc: Qiang Zhao <qiang.zhao@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This is the only platform defining and using CONFIG_SYS_MEM_SIZE, switch
to using CONFIG_SYS_SDRAM_SIZE for consistency.
Cc: Paul Burton <paul.burton@mips.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
We have a number of CONFIG_SYS_xxx_SIZE options to describe the amount
main memory available. Rework CONFIG_SYS_DDR_SIZE, which described a
size in number of MiB to use CONFIG_SYS_SDRAM_SIZE which is most often
used as a number of bytes. Use shifts of this option when required.
Signed-off-by: Tom Rini <trini@konsulko.com>
Since commit 103c5f1806 ("mmc: Rename MMC_SUPPORT to MMC"),
SPL_MMC_SUPPORT is named SPL_MMC, so let's fix the ifdef.
Fixes: fbc6b14143 ("imx: imx8mp_rsb3720a1: convert to DM_SERIAL")
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
On some boards upper 4 bits of i2c boot input data (register 0) are
inverted. Information which bits are inverted is stored in register 2.
So invert read input data back according to register 2 prior processing
them. This fixes printing "rom_loc: value" line during booting.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
U-Boot for initial L2 SRAM uses L2 memory-mapping mode and not L2 with
locked lines. P2020 reference manual about L2 memory-mapping mode says:
Accesses to memory-mapped SRAM are cacheable only in the corresponding
e500 L1 caches.
So there is no need to set Caching-Inhibit I-bit for second part of initial
L2 SRAM mapping in TLB entry. Remove it. First part of initial L2 SRAM
mapping already does not have I-bit set.
For more details see also:
https://lore.kernel.org/u-boot/20220508150844.qqxg452rs4wtf5bs@pali/
Signed-off-by: Pali Rohár <pali@kernel.org>
This driver registers GPIO controller and allows U-Boot to control GPIO
pins on MCU which is connected to Turris Omnia via i2c.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
start of test for fdt command
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmLgRtERHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreYXFwgAlALOMj3bwwsIAXNa5j/hPb3j/ecIqXgn
ocyxN+U5eSb2Ju5Jc9QmSeUMnGrii9+PW9j0JApdHrbUgBI2Sx+zwqMTIfA+BS05
4xXZgk5jOT+we2489FjgFcplv+dIuVlsB/Zo6zTbZyjkobfilYsZEGYHJ/CYNaIH
n7EmZeby1cXL7DMCxT39d3hD43XSX8cqQ1IIiF9DgtHQYs2Ff8dFcbWArSdgLX3o
Eob2Qj/GjScg87zjZcsgZajWJMHUfMeD5ZiKN2fR0T/wOdO1WtzFoF2Mt8KZcW1j
BD1shgBCMSSl5EgRG1BQZw4Sa92W2IBlbJ9tfIh8qnWOzEBzOs/M6w==
=lsO4
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-26jul22' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm.git
minor dm- and fdt-related fixes
start of test for fdt command
Set ARM clock to OD frequency 1.7Ghz, since we have set PMIC VDD_SOC
to Overdrive voltage 0.9V
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Since iMX9 uses S401 which shares the API with iMX8ULP. So move S400
MU driver and API to a common place and selected by CONFIG_IMX_SENTINEL
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Update this feature so that it works on sandbox, using a basic identity
mapping. This allows us to run the 'ut addrmap' test.
Also fix up the test to use the correct macros to access the linker
list, so that the 'ut addrmap' command actually works.
Signed-off-by: Simon Glass <sjg@chromium.org>
Store a set of supported bitstream types in xilinx_desc structure.
It will be used to determine whether an FPGA image is able to be
loaded with a given driver.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Tested-by: Ricardo Salveti <ricardo@foundries.io>
Tested-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Link: https://lore.kernel.org/r/20220722141614.297383-4-oleksandr.suvorov@foundries.io
Signed-off-by: Michal Simek <michal.simek@amd.com>
UUID is already recorded when FRU is parsed but it is not copied to local
structures and exported to variable that's why simply add it.
Data is saved in binary format but there must be conversion to string for
exporting it to variable and string should be in uuid format too.
One way how to use it directly is to setup pxeuuid based on it. For
example via preboot with "setenv pxeuuid ${board_uuid}"
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/1dfa4b4220a508abc05351da2119880811b77612.1658413156.git.michal.simek@amd.com
With commit ce39ee28ec ("zynqmp: Do not place u-boot to reserved memory
location"), the function board_get_usable_ram_top() is allocating
MMU_SECTION_SIZE of about 2MB using lmb_alloc(). But we dont have this
much memory in case of mini U-Boot.
Keep these functions which use lmb under CONFIG_LMB so that they are
compiled and used only when LMB is enabled.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/75e52def75f573e554a6b177a78504c128cb0c4a.1657183534.git.michal.simek@amd.com
The first AM6x device was the AM654x, but being the first we named it
just AM6, since more devices have come out with this same prefix we
should switch it to the normal convention of using the full name of the
first compatibility device the series. This makes what device we are
talking about more clear and matches all the K3 devices added since.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This is no longer needed as the SA2UL can now be shared with Linux.
Leave the SA2UL DT node enabled.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add support for Qualcomm QCS404 SoC based evaluation board.
Features:
- Qualcomm Snapdragon QCS404 SoC
- 1GiB RAM
- 8GiB eMMC, uSD slot
U-boot is chain loaded by ABL in 64-bit mode as part of boot.img.
For detailed build and boot instructions, refer to
doc/board/qualcomm/qcs404.rst.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Add support for 96Boards Dragonboard 845C aka Robotics RB3 development
platform. This board complies with 96Boards Open Platform Specifications.
Features:
- Qualcomm Snapdragon SDA845 SoC
- 4GiB RAM
- 64GiB UFS drive
U-boot is chain loaded by ABL in 64-bit mode as part of boot.img.
For detailed build and boot instructions, refer to
doc/board/qualcomm/sdm845.rst, board: dragonboard845c.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
We have different dtbs for the Lite and Extended WiFi variants of the
SanCloud BBE.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The SanCloud BBE Lite has a Micron Authenta flash device connected to
the spi0 bus.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Synchronise device tree with linux v5.19-rc5.
Please note that this also means that instead of the previous "generic"
U-Boot specific carrier board agnostic device tree we are now using the
regular one for the Verdin Development (carrier) board (e.g.
imx8mp-verdin-wifi-dev.dtb rather than the previous imx8mp-verdin.dtb).
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Synchronise device tree with linux v5.19-rc5.
Please note that this also means that instead of the previous "generic"
U-Boot specific carrier board agnostic device tree we are now using the
regular one for the Verdin Development (carrier) board (e.g.
imx8mm-verdin-wifi-dev.dtb rather than the previous imx8mm-verdin.dtb).
Please further note that the PMIC node name got changed from a pmic
label to pmic@25 which required adjustment in resp. board SPL file
board/toradex/verdin-imx8mm/spl.c.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Synchronise device tree with linux v5.19-rc5.
Please note that this also means that instead of the previous "generic"
U-Boot specific carrier board agnostic device tree we are now using the
regular one for the Colibri Evaluation (carrier) board V3 (e.g.
vf610-colibri-eval-v3.dtb rather than the previous vf610-colibri.dtb).
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Synchronise device tree with linux-next next-20220708.
Please note that this also means that instead of the previous "generic"
U-Boot specific carrier board agnostic device trees we are now using the
regular ones for the Colibri Evaluation (carrier) board V3 (e.g.
imx7d-colibri-eval-v3.dtb rather than the previous
imx7-colibri-rawnand.dtb and imx7d-colibri-emmc-eval-v3.dtb rather than
the previous imx7-colibri-emmc.dtb).
Please further note that the PMIC node name got changed from rn5t567@33
to pmic@33 which required adjustment in resp. board file
board/toradex/colibri_imx7/colibri_imx7.c.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Synchronise device tree with linux v5.19-rc5.
Please note that this also means that instead of the previous "generic"
U-Boot specific carrier board agnostic device trees we are now using the
regular ones for the Colibri Evaluation (carrier) board V3 (e.g.
imx6ull-colibri-eval-v3.dtb rather than the previous imx6ull-colibri.dtb
and imx6ull-colibri-emmc-eval-v3.dtb rather than the previous
imx6ull-colibri-emmc.dtb).
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Synchronise device tree with linux-next next-20220708.
Please note that this also means that instead of the previous "generic"
U-Boot specific carrier board agnostic device tree we are now using the
regular one for the Colibri Evaluation (carrier) board V3 (e.g.
imx6dl-colibri-eval-v3.dtb rather than the previous imx6-colibri.dtb).
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Synchronise device tree with linux-next 20220706.
Please note that this also means that instead of the previous "generic"
U-Boot specific carrier board agnostic device tree we are now using the
regular one for the Apalis Evaluation (carrier) board (e.g.
imx6q-apalis-eval.dtb rather than the previous imx6-apalis.dtb).
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Add product id print in show_board_info(), with an increasing number of
Toradex SKUs available with small differences it makes sense to print it.
Move serial number print to a dedicated line, this prevents the previous
line with the product name to overflow the 80 columns with any
reasonable product name length.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Up to now in the code we named Toradex SKUs in a slightly different way
compared to the official product name, start using the official names
from now on to avoid misunderstanding.
This has also the nice benefit of the string being shorter, allowing
to fit nicely in 80 columns even adding the product ID when printing
the hardware information.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Fix checkpatch warn, use `IS_ENABLED(CONFIG_TDX_CFG_BLOCK_2ND_ETHADDR)`
instead of `#ifdef CONFIG_TDX_CFG_BLOCK_2ND_ETHADDR`.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Remove stale show_boot_logo() declaration, not used anywhere.
Fixes: e6fd30dd9e ("toradex: drop legacy show_boot_logo function and use splashscreen")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Simplify interactive config block creation code, instead of having a
a long list of questions and a complex tree of preprocessor directive to
guess the exact SKU, just ask the user to select it from a list.
The modules list is filtered out to include only SKUs that are supported
by the specific u-boot binary in execution.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Use generally available ARRAY_SIZE macro, instead of hand-coding it
every time is needed.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Remove comment "not currently on sale" on specific SKUs, this
information does not belong to the code and will never be accurate.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Add new i.MX 8M Mini SKU to ConfigBlock handling.
0068: Verdin iMX8M Mini Quad 2GB WB IT No CAN
This SKU is identical to 0055 but without CAN. Mention this in the name
so those modules can be distinguished.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Add entry for imx8mm_evk_fspi_defconfig in
board/freescale/imx8mm_evk/MAINTAINERS
Signed-off-by: Mamta Shukla <mamta.shukla@leica-geosystems.com>
Signed-off-by: Thomas Haemmerle <thomas.haemmerle@leica-geosystems.com>
Tested-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Add QSPI Boot option in u-boot-spl for i.MX8m EVK.
Signed-off-by: Mamta Shukla <mamta.shukla@leica-geosystems.com>
Signed-off-by: Thomas Haemmerle <thomas.haemmerle@leica-geosystems.com>
Tested-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Add imx8mm_evk_fspi_defconfig to build QSPI boot image.
This config is based on imx8mm_evk_defconfig with addtional config options to
define FSPI Header parameters required to generate QSPI Header.
Update SPL offset to include header size and overwrite IMX_CONFIG to use
lpddr.cfg for FSPI.
Signed-off-by: Mamta Shukla <mamta.shukla@leica-geosystems.com>
Signed-off-by: Thomas Haemmerle <thomas.haemmerle@leica-geosystems.com>
Tested-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
ft_board_setup relies on the board_type() function to optimize which phy
nodes need to be enabled for Linux.
Add calls to setup and release the board-detect GPIOs.
Also fix the switch-case statement to only enable phy address 4 for
Cubox and unknown devices.
Fixes: 741ce308 ("mx6cuboxi: fixup dtb ethernet phy nodes before booting an OS")
Signed-off-by: Josua Mayer <josua@solid-run.com>
Fix diacritics in some instances of my name and change my e-mail address
to kabel@kernel.org.
Add corresponding .mailmap entries.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Fix MAINTAINERS files for Turris devices, add missing files and add Pali
as maintainer.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
I am currently maintaing the Methode uDPU and eDPU boards so add myself
as the maintainer for them.
Remove the old entry from board/Marvell/mvebu_armada-37xx/MAINTAINERS.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
It does not matter what is DT node name of atsha device. So find it via
atsha driver and not by DT node name.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
The mt7621_rfb board supports integrated giga PHYs plus one external
giga PHYs. It also has up to 512MiB DDR3, 16MB SPI-NOR, 3 mini PCI-e x1
slots, SDXC and USB.
The mt7621_nand_rfb board is almost the same as mt7621_rfb board, but it
uses NAND flash and SDXC is not available.
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
On p1_p2_rdb_pc platforms, we set ddr_data_init to the "poison" value of
0xdeadbeef rather than a real calculated / derived value. Do this
directly and comment rather than via CONFIG.
Signed-off-by: Tom Rini <trini@konsulko.com>
Perform a basic migration of the calls in setup_serial_number() to DM so
that we can switch to using DM_I2C on this platform.
Cc: David Lechner <david@lechnology.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: David Lechner <david@lechnology.com>
We only reference CONFIG_SYS_BFTIC3_BASE in one location. Move the
comment to where we reference it, and use the value directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Holger Brunck <holger.brunck@hitachienergy.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Add new Toradex MAC OUI (8c:06:cb), to the config block. With this change
we extend the possible serial-numbers as follows:
For serial-numbers 00000000-16777215 OUI 00:14:2d is taken
For serial-numbers 16777216-33554431 OUI 8c:06:cb is taken
Lower 24-bit of the serial number are used in the NIC part of the
MAC address, the complete serial number can be calculated using the OUI.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Do 1 byte address checks first prior to doing 2 byte address checks.
When performing 2 byte addressing on 1 byte addressing eeprom, the
second byte is taken in as a write operation and ends up erasing the
eeprom region we want to preserve.
While we could have theoretically handled this by ensuring the write
protect of the eeproms are properly managed, this is not true in case
where board are updated with 1 byte eeproms to handle supply status.
Flipping the checks by checking for 1 byte addressing prior to 2 byte
addressing check prevents this problem at the minor cost of additional
overhead for boards with 2 byte addressing eeproms.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Due to supply chain issues, we are starting to see a mixture of eeprom
usage including the smaller 7-bit addressing eeproms such as 24c04
used for eeproms.
These eeproms don't respond well to 2 byte addressing and fail the
read operation. We do have a check to ensure that we are reading the
alternate addressing size, however the valid failure prevents us
from checking at 1 byte anymore.
Rectify the same by falling through and depend on header data comparison
to ensure that we have valid data.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The eeprom data area is much bigger than the data we intend to store,
however, with bad programming, we might end up reading bad records over
and over till we run out of eeprom space. instead just exit when 10
consecutive records are read.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Call into k3-ddrss driver to fixup device tree and resize
the available amount of DDR if ECC is enabled.
A second fixup is required from A53 SPL to take the fixup
as done from R5 SPL and apply it to DT passed to A53 U-boot,
which in turn passes this to the OS.
Signed-off-by: Georgi Vlaev <g-vlaev@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Use the appropriate fdtdec_setup_mem_size_base() call in
dram_init() and fdtdec_setup_bank_size() in dram_bank_init()
to pull these values from DT, where they are already available,
instead of hardcoding them.
Signed-off-by: Georgi Vlaev <g-vlaev@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
There are two decimal digits reserved to encode the module version and
revision. This code so far implemented A-Z which used 0-25 of this
range.
This commit extends the range to make use of all 99 numbers. After
capital letters the form with a hashtag and number (e.g. #26) is used.
Examples:
If the assembly version is between zero and 25 the numbering is as follows,
as it also has been before this commit:
0: V0.0A
1: V0.0B
...
25: V0.0Z
New numbering of assembly version:
If the number is between 26 and 99 the new assembly version name is:
26: V0.0#26
27: V0.0#27
...
99: V0.0#99
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
With those defines the length can be reused and is in one place
extendable.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Prevent memory issues that could appear with sprintf. Replace all
sprintf occurences with snprintf.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
While configuring SerDes, errors could be encountered, in these cases,
return instead of going ahead. This is will help in booting even if
configuration of SerDes fails.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
These CONFIG options are only used on this board, in the board file
itself. Remove these from the CONFIG namespace and define in the board
file.
Signed-off-by: Tom Rini <trini@konsulko.com>
The symbol CONFIG_PCI_CLK_FREQ is local to this board. Provide equal
clarity in the code by referencing the numeric value directly and move
the explanatory comment to the code, just prior to use.
Signed-off-by: Tom Rini <trini@konsulko.com>
As things stand currently, there is only one PowerPC platform that
enables the options for CHAIN_OF_TRUST. From the board header files,
remove a number of never-set options. Remove board specific values from
arch/powerpc/include/asm/fsl_secure_boot.h as well. Rework
include/config_fsl_chain_trust.h to not abuse the CONFIG namespace for
constructing CHAIN_BOOT_CMD. Migrate all of the configurable addresses
to Kconfig.
If any platforms are re-introduced with secure boot support, everything
required should still be here, but now in Kconfig, or requires migration
of an option to Kconfig.
Cc: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Move setting of SPL_UBOOT_KEY_HASH to a non-NULL value to Kconfig. As
part of this, change fsl_secboot_validate(...) to check that it is
passed a non-empty string, rather than non-NULL.
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Kshitiz Varshney <kshitiz.varshney@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Make all of the CHAIN_OF_TRUST options be under a single menu and add a
comment for the rest, so the resulting config file reads more clearly.
Remove duplicate CHAIN_OF_TRUST options from
board/congatec/common/Kconfig. Remove duplicate NXP_ESBC config
questions and move to arch/Kconfig.nxp.
Signed-off-by: Tom Rini <trini@konsulko.com>
Now that board/freescale/common/Kconfig is safe to be included once,
globally, rename this to arch/Kconfig.nxp to better reflect that it
contains options that are valid on multiple architectures and SoC
families, and not specific to NXP reference platforms either.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The way that we use this file currently means that we have to guard it
in every platform Kconfig. But it is also required in all NXP
platforms, including non-reference platforms. Make all options in it
have appropriate dependencies so that we can include it a single time
under arch/Kconfig
Signed-off-by: Tom Rini <trini@konsulko.com>
We rename the S5P specific "CONFIG_PWM" to CONFIG_PWM_S5P and move it to
Kconfig. Given the usage of CONFIG_PWM_NX, we have that select this new
symbol.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
From whole P1/P2 family of RDB boards is TDM-PMC card (PCI Mezzanine Card,
Freescale PQ-MDS-T1) available only on P1021RDB and P1025RDB boards.
So address mapping for TDM-PMC card on LBC should not be enabled on any
other P1/P2 RDB board as there is no device at that TDM-PMC address.
Support for P1021RDB and P1025RDB boards was already removed from mainline
U-Boot in commits 6d1dd76afe ("board/freescale: Remove P1021RDB board
support") and d521cece5a ("board/freescale: Remove P1025RDB board
support").
So do not enable TDM-PMC address mapping on remaining P1/P2 RDB boards and
remove all macros related to TDM-PMC address mappings.
Signed-off-by: Pali Rohár <pali@kernel.org>
Since I'm leaving the company with end of June, the maintainership will
be transferred to Wolfgang Wallner.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmK9nEUcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyEu0B/4v1EQOMBL+VXns8Ipo
Xeq+RDUX/24XcB5s6sTcNlWzvYuX6Z7DCGJ0loK5JxelrOy+YNkRbTRMom1eW9Kn
9dmKa0bcO7auJEww3Nln1IFyx+FXQFGR1V3g1U4535l8b7urTioIK0MUSrG/GLpe
Rlbh31GAYtrGvl06W1F7mwhg7/0AT8IhUFaY9G7s7gKA5muGQQ7ED4nKVoZPeTAl
lrQ/Ecym1ND7aOhd/vuEBtgoGxDWzwf8piT8qykJluJKzBV1Hic0RXCNBmtrTORz
b1GOOpRUgcnTv9U8j4PRyYGKDnmS2OmV2AwL8+V9UJfJgQrkcRlbgpCysIPmMBzo
YPRt
=D79P
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2022.10-a' of https://source.denx.de/u-boot/custodians/u-boot-at91 into next
First set of u-boot-at91 features for the 2022.10 cycle:
This feature set includes mostly fixes and alignments: DT alignment with
Linux for sama7g5, removal of invalid eeprom compatibles, removal of
extra debug_uart_init calls for all at91 boards, support for pio4 driver
pioE bank, and other minor fixes and enhancements for sam9x60 and
sama5d2_icp boards.
Move the environment text over from being set via
CONFIG_EXTRA_ENV_SETTINGS in include/configs/gw_ventana.h and over
to plain text in board/gateworks/gw_ventana/gw_ventana.env. This lets
us drop CONFIG_EXTRA_ENV_SETTINGS_COMMON as everything resides in a
single environment file now.
Cc: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Move the environment text over from being set via
CONFIG_EXTRA_ENV_SETTINGS in include/configs/opos6uldev.h and over to
plain text in board/armadeus/opos6uldev/opos6uldev.env. This lets us
manage env_version without a CONFIG variable.
Cc: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
With the exception of distro_boot support, we can move all of the rest
of the environment changes to come from CONFIG_EXTRA_ENV_TEXT and in
turn remove CONFIG_ENV_REFLASH.
Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This define is only currently used in a single board, and always set to
one. Define this within the board code and remove other references.
Signed-off-by: Tom Rini <trini@konsulko.com>
Introduce board/siemens/common/Kconfig and have it hold FACTORYSET to
start with. Use select for this on the boards that need it.
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Samuel Egli <samuel.egli@siemens.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
- In a number of cases, use CONFIG_ARCH_EXYNOS[45] rather than
CONFIG_EXYNOS[45]
- In other cases, test for CONFIG_ARCH_EXYNOS or CONFIG_ARCH_S5PC1XX
- Migrate specific SoC CONFIG values to Kconfig
- Use CONFIG_TARGET_x rather than CONFIG_x
- Migrate other CONFIG_EXYNOS_x symbols to Kconfig
- Reference CONFIG_EXYNOS_RELOCATE_CODE_BASE directly as EXYNOS_RELOCATE_CODE_BASE
- Rename CONFIG_S5P_PA_SYSRAM to CONFIG_SMP_PEN_ADDR to match the rest
of U-Boot usage.
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Since bb5930d5c9 ("exynos: video: Convert several boards to driver
model for video") there have been no callers of any of the exynos_lcd_*
family of functions. Remove these from the boards, and then remove
unused logo and related code as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
The only platform currently that defines an ide_preinit function has an
empty one that immediately returns. Remove this hook.
Signed-off-by: Tom Rini <trini@konsulko.com>
We want to keep all of the default values for SPL_LDSCRIPT in the same
place both for overall clarity as well as not polluting unrelated config
files.
Signed-off-by: Tom Rini <trini@konsulko.com>
Add CAAM support, which is required when enabling HAB secure boot.
Select CONFIG_SPL_DRIVERS_MISC so that CONFIG_IMX_HAB could
build successfully, if selected.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Acked-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Do DDR initialization using the procedural mx6_dram_cfg() instead of
programming the MMDC using a raw list of register/value pairs, this
solves some rare boot failures on specific "bad" modules.
Calibration values, DDR geometry are unchanged, memory timings are
updated according to the relevant memory datasheet, no changes on
the power consumption.
For IT temperature range SKUs CL is decreased from 8 to 7 and tFAW
value is increased, for commercial temperature range SKUs some
changes on ODT parameters.
This change was validated over a range of different apalis-imx6 SoM, on
the whole working temperature range with weeks of continuous testing.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Set CLK01 and CLK02 to 24MHz and enable it in CCM_CCOSR register.
This clock is used by both the audio codec (CLKO1) and by the CSI camera
(CLKO2) and is expected to be 24MHz.
Despite the wrong 16.5MHz there was no real issue because of the wrong
frequency since Linux reconfigures the clocks afterward, however this
was triggering an issue with noise coming from the SGTL5000 audio codec.
The problem is that the SGTL5000 does not have a reset pin and after it
is configured if the input MCLK clock is disabled it produces a constant
noise on its output, this was happening on software reboot.
Forcing the clock to be enabled in U-Boot prevent the problem by making
sure that the clock is always available, without this change as soon as
Linux was changing the clock tree (setting clk_out_sel=1 without setting
clko2_en=1) the noise would start till the actual clock was enabled
(clko2_en=1) during the SGTL5000 driver probe.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Since 0dba45864b ("arm: Init the debug UART") ,
the debug_uart_init is now called from crt.S
It's no longer required to call it from the board file.
With the current code, the banned <debug_uart> is printed twice:
<debug_uart>
<debug_uart>
U-Boot 2022.07-rc4-00089-gee3d158fa8 (Jun 08 2022 - 17:39:29 +0300)
Remove all calls from board_early_init_f .
Suggested-by: Balamanikandan Gunasundar <Balamanikandan.Gunasundar@microchip.com>
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
cpu:
- Add driver for microblaze cpu
net:
- Add support for DM_ETH_PHY to AXI emac and emaclite
xilinx:
- Switch platforms to DM_ETH_PHY
- DT chagnes in ZynqMP and Zynq
- Enable support for SquashFS
zynqmp:
- Add support for KR260 boards
- Move BSS from address 0
- Move platform identification from board code to soc driver
- Improve zynqmp_psu_init_minimize
versal:
- Enable loading app at EL1
serial:
- Setup default address and clock rates for DEBUG uarts
pinctrl:
- Add support for tri state and output enable properties
relocate-rela:
- Clean relocate-rela implementation for ARM64
- Add support for Microblaze
microblaze:
- Add support for runtime relocation
- Rework cache handling (wiring, Kconfig) based on cpuinfo
- Remove interrupt support
timer:
- Extract axi timer driver from Microblaze to generic location
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYrlYngAKCRDKSWXLKUoM
ITgbAJ9S9xO2QqxtuodWAYMtJfvZ14c7mgCeKnyFTrrBnJkC0wPsGqE71oNJ49o=
=3gGm
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.10' of https://source.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2022.10
cpu:
- Add driver for microblaze cpu
net:
- Add support for DM_ETH_PHY to AXI emac and emaclite
xilinx:
- Switch platforms to DM_ETH_PHY
- DT chagnes in ZynqMP and Zynq
- Enable support for SquashFS
zynqmp:
- Add support for KR260 boards
- Move BSS from address 0
- Move platform identification from board code to soc driver
- Improve zynqmp_psu_init_minimize
versal:
- Enable loading app at EL1
serial:
- Setup default address and clock rates for DEBUG uarts
pinctrl:
- Add support for tri state and output enable properties
relocate-rela:
- Clean relocate-rela implementation for ARM64
- Add support for Microblaze
microblaze:
- Add support for runtime relocation
- Rework cache handling (wiring, Kconfig) based on cpuinfo
- Remove interrupt support
timer:
- Extract axi timer driver from Microblaze to generic location
Commit e42dad4168 ("sunxi: use boot source for determining environment
location") changed our implementation of env_get_location() and enabled
it for every board, even those without MMC support (like the C.H.I.P.
boards). However the default fallback location of ENVL_FAT requires MMC
support compiled in, so the board hangs when trying to initially load
the environment.
Change the algorithm to only return configured environment locations,
and improve the fallback algorithm on the way.
The env_init() routine calling this function here does not behave well
if the return value is ENVL_UNKNOWN on the very first call: it will make
U-Boot proper silently hang very early.
Work around this issue by making sure we return some configured (dummy)
environment location when prio is 0. This for instance happens when
booting via FEL.
This fixes U-Boot loading on the C.H.I.P. boards.
Fixes: e42dad4168 ("sunxi: use boot source for determining environment location")
Reported-by: Chris Morgan <macroalpha82@gmail.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
[Andre: fix FEL boot case by not returning ENVL_UNKNOWN when prio==0]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The set_dfu_alt_info function use the CONFIG_SYS_SPI_U_BOOT_OFFS define
to set the dfu_alt_info environment variable for qspi boot mode. Guard
the usage of CONFIG_SYS_SPI_U_BOOT_OFFS to make spi flash support
optional.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Link: https://lore.kernel.org/r/20220620163650.18756-11-stefan.herbrechtsmeier-oss@weidmueller.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add machine identification support based on the
zynqmp_get_silicon_idcode_name function and use the soc_get_machine
function of the soc uclass to get silicon idcode name for the fpga init.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Link: https://lore.kernel.org/r/20220620163650.18756-8-stefan.herbrechtsmeier-oss@weidmueller.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add helper code for PVR (Processor Version Register) data handling. It
will be used by the UCLASS_CPU driver to populate cpuinfo fields at
runtime.
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Link: https://lore.kernel.org/r/20220531181435.3473549-13-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Provide a static Kconfig value for the target FPGA archtitecture, as it is
done in Linux. The cpu-uclass driver will cross-check it with the value
read from PVR10 register.
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Link: https://lore.kernel.org/r/20220531181435.3473549-12-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Replace XILINX_DCACHE_BYTE_SIZE macro with two Kconfig symbols for
instruction and data caches sizes, respectively:
CONFIG_XILINX_MICROBLAZE0_ICACHE_SIZE
CONFIG_XILINX_MICROBLAZE0_DCACHE_SIZE
Also, get rid of the hardcoded value in icache_disable().
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Link: https://lore.kernel.org/r/20220531181435.3473549-8-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com> (s/bralid/brlid/g)
Replace CONFIG_ICACHE with a Kconfig option more limited in scope -
XILINX_MICROBLAZE0_USE_WIC. It should be enabled if the processor supports
the "wic" (Write to Instruction Cache) instruction. It will be used to
guard "wic" invocations in microblaze cache code.
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Link: https://lore.kernel.org/r/20220531181435.3473549-6-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Replace CONFIG_DCACHE with a Kconfig option more limited in scope -
XILINX_MICROBLAZE0_USE_WDC. It should be enabled if the processor supports
the "wdc" (Write to Data Cache) instruction. It will be used to guard
"wdc" invocations in microblaze cache code.
Also, drop all ifdefs around flush_cache() calls and only keep one
CONFIG_IS_ENABLED() guard within flush_cache() itself.
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Link: https://lore.kernel.org/r/20220531181435.3473549-5-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add support to switch to EL1 and load an EL1 app from U-Boot which is
executing at EL2 or EL3 in aarch64 mode.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/20220506055345.1921-1-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Rename the sections used to implement linker lists so they begin with
'__u_boot_list' rather than '.u_boot_list'. The double underscore at the
start is still distinct from the single underscore used by the symbol
names.
Having a '.' in the section names conflicts with clang's ASAN
instrumentation which tries to add redzones between the linker list
elements, causing expected accesses to fail. However, clang doesn't try
to add redzones to user sections, which are names with all alphanumeric
and underscore characters.
Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- Correct livetree support in stm32mp1 boards
- Activate livetree for stm32mp15 DHSOM boards
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAmKsehgACgkQ4rK92eCq
k3UexAf+JThCd7FlN3OkTVKIdZKeNm2KpQxrqt20whiqp/nSUzxXrjdlCTKZEER2
lLJoVnwr+bkmdlqsa6gAZXSsd0lUv37XnLsLA5or278tFNlKp6gzYrz49FR59mVC
ie7/NlY5FgM5qmKGCob7tjwJ78r2/S3T2EaLiAMWUmw2UB5KZU6h3napHZ+1T0se
vaEAVRzAaZeYzKU3k6RBSv2tXQ6ssvfpp9RcXpRGtrN908AqDhHiOfntuOrnsEe0
9rjY1DSXO9a5WqHRm2KQ3FrA/By2layQ+4WH/HgIPHasisnmo3E/euVWmhtTaiT/
g5bOLwyFQ2/RvdMlMxXlKUcuMfNwRA==
=Hhzj
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20220620' of https://source.denx.de/u-boot/custodians/u-boot-stm into next
- Add STM32MP13 SoCs support with associated board STM32M135F-DK
- Correct livetree support in stm32mp1 boards
- Activate livetree for stm32mp15 DHSOM boards
The board supports up to 8 GiB memory. The memory is soldered on the
board but the configuration is equivalent to a dual chip select, dual
rank DIMM module.
Signed-off-by: Michael Walle <michael@walle.cc>
With a 8GiB memory board, it seems that the "very unlikely event" of a
DDR initialization with non-optimal values are not really that unlikely.
It happens in about every other reboot. As described in erratum
A-009942, preset the DEBUG_28 register with an optimal value. The value
iself depends on the memory configuration of the board, but the used
value seems to work well for all variants.
Signed-off-by: Michael Walle <michael@walle.cc>
This patch adds config support for HDP firmware loading on LS1028A.
Signed-off-by: Oliver Brown <oliver.brown@nxp.com>
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Depending on backup register value, U-Boot SPL maintains the debug unit
powered-on for debugging purpose; only BUCK1 is required for powering
the debug unit, so revert the setting for all the other power lanes,
except BUCK3 that has to be always on.
To be functional this patch requires a modification in the debugger
,openocd for example, to update the STM32MP15 backup register when it is
required to debug SPL after reset. After deeper analysis this behavior
will be never supported in tools so the associated code, will be never
used and the associated code can be removed.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Replace call to fdt_*() functions and access to gd->fdt_blob
with call to ofnode_*() functions to support a live tree.
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Replace gd->fdt_blob access with fdt_getprop() function to the
function ofnode_get_property() to support a live tree.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Replace gd->fdt_blob access with fdt_getprop() function to the
function ofnode_get_property() to support a live tree.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add a initial config for STM32M13x SOC family, using the stm32mp135f-dk
device tree.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add stm32mp15x prefix to all STM32MP15x board specific functions,
this patch is a preliminary step for STM32MP13x support.
This patch also adds the RCC probe to avoid circular access with
usbphyc probe as clk provider.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Introduce the code in mach-stm32mp and the configuration file
stm32mp13_defconfig for the new STM32MP family.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add initial support of STM32MP13 family based on v5.18-rc2
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add DT for DH DRC Compact unit, which is a universal controller device.
The system has two ethernet ports, one CAN, RS485 and RS232, USB, uSD
card slot, eMMC and SDIO Wi-Fi.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The origin of this patch is the breaking of am335x-hs boot
due to commit e41651fffd ("dm: Support parent devices with of-platdata")
HS boards have less SRAM for SPL and so this commit increased memory usage beyond am335x limit.
This commit added 10 driver binding pass and am335x boot only if one pass is done.
SPL try to do more than one pass due to eth_cpsw failing.
Since HS SPL does not need network (and NET is already disabled in config),
the easiest fix is to "remove" eth_cpsw from SPL by testing if NET is enabled.
Signed-off-by: Corentin LABBE <clabbe@baylibre.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Andrew Davis <afd@ti.com>
pinctrl_wdog already marked u-boot,dm-spl, so clean up board code.
The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Teresa Remmet <t.remmet@phytec.de>
Mark pinctrl_wdog as u-boot,dm-spl to clean up board code,
The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Mark wdog1/pinctrl_wdog as u-boot,dm-spl to clean up board code,
The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
pinctrl_wdog already marked u-boot,dm-spl, so clean up board code.
The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
Mark pinctrl_wdog as u-boot,dm-spl to clean up board code,
The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Mark pinctrl_wdog as u-boot,dm-spl to clean up board code,
The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Mark pinctrl_wdog as u-boot,dm-spl to clean up board code,
The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Mark pinctrl_wdog as u-boot,dm-spl to clean up board code,
The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Enable CONFIG_DM_SERIAL. uart and its pinmux was already
marked with u-boot,dm-spl.
Move preloader_console_init after spl_init to make sure driver
model work.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Enable CONFIG_DM_SERIAL. uart and its pinmux was already
marked with u-boot,dm-spl.
Move preloader_console_init after spl_init to make sure driver
model work.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Enable CONFIG_DM_SERIAL. uart and its pinmux was already
marked with u-boot,dm-spl.
Move preloader_console_init after spl_early_init to make sure driver
model work.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Enable CONFIG_SPL_DM_SERIAL. uart2 and its pinmux was already
marked with u-boot,dm-spl.
Move preloader_console_init after spl_early_init to make sure driver
model work.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Enable CONFIG_DM_SERIAL. uart3 and its pinmux was already
marked with u-boot,dm-spl.
Move preloader_console_init after spl_early_init to make sure driver
model work.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Enable CONFIG_SPL_DM_SERIAL. uart2 and its pinmux was already
marked with u-boot,dm-spl.
Move preloader_console_init after spl_init to make sure driver
model work.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Adam Ford <aford173@gmail.com> #imx8mm_beacon
Reviewed-by: Fabio Estevam <festevam@denx.de>
Tested-by: Adam Ford <aford173@gmail.com> #imx8mn_beacon
SoM revision 1.9 has replaced the ar8035 phy address 0 with an adin1300
at address 1. Because early SoMs had a hardware flaw, the ar8035 can
also appear at address 4 - making it a total of 3 phy nodes in the DTB.
To avoid confusing Linux with probe errors, fixup the dtb to only enable
the phy node that is detected at runtime.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Add the new Apalis iMX8 product variant
0067: Apalis iMX8 QuadMax 8GB Wi-Fi / BT IT
the only difference to the product
0037 Apalis iMX8 QuadMax 4GB Wi-Fi / BT IT
is the 8gb of RAM. Toradex strategy to choose the correct RAM timing in
SCFW is by fuses in the user area telling which RAM timing to load.
This commit makes use of this information to set the correct size of
the RAM and therefore distinguish between the new 0067 and 0037 product
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
0067: Apalis iMX8 QuadMax 8GB Wi-Fi / BT IT
This module is identical to its 4GB counterpart
0037: Apalis iMX8 QuadMax 4GB Wi-Fi / BT IT
except for the RAM size.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Use device tree to set MAC address of the Ethernet chip.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add am62x_evm_r5_defconfig for R5 SPL and am62x_evm_a53_defconfig for
A53 SPL and U-Boot support.
To keep the changes to minimum. Only UART And SD boot related configs
are included. This should serve as good starting point for new board
bringup with AM62x.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
[trini: Migrate a number of CONFIG symbols, have re-tested]
Tested-by: Georgi Vlaev <g-vlaev@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Add basic support for AM62 SK. This has 2GB DDR.
Note that stack for R5 SPL is in OCRAM @ 0x7000ffff so that is away from
BSS and does not step on BSS section
Add only the bare minimum required to support UART and SD.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This is the initial support for Broadcom's ARM-based 47622 SOC.
In this change, our first SOC is an armv7 platform called 47622. The
initial support includes a bare-bone implementation and dts with ARM
PL011 uart.
The SOC-specific code resides in arch/arm/mach-bcmbca/<soc> and board
related code is in board/broadcom/bcmba.
The u-boot image can be loaded from flash or network to the entry
point address in the memory and boot from there.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Kursad Oney <kursad.oney@broadcom.com>
Signed-off-by: Anand Gore <anand.gore@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
On j721e, its not possible to use OSPI0 and HBMC simultaneously as they
are muxed within the Flash Subsystem hence disable HBMC by default and
keep OSPI enabled. Bootloader will fixup DT when it detects HyperFlash
mux selection instead of OSPI.
Also updated detect_enable_hyperflash to use correct GPIO when checking
hypermux selection state:
* J7200 - hypermux sel connected to WKUP_GPIO0_6
* J721E - hypermux·sel·connected·to·WKUP_GPIO0_8
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
This prevents some conflicts when running sandbox with -D, since the
"rom" mac address will be random and won't match the environment. We
still need to keep addresses for eth1 and eth6 in the environment,
because dm_test_eth_rotate expects to be able to disable them by
removing their envaddr variables. This can likely be fixed in a future
series by adding a function to cause sandbox eth_opts callback for a
particular mac to fail immediately.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
DSA interfaces use the same mac address for each interface, unless
instructed otherwise. Just set eth4addr and let eth2addr and eth7addr be
set automatically.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The phy_eth0 interface introduced in commit f3dd213e15 ("net: introduce
helpers to get PHY ofnode from MAC") uses a globally-administered
address. Switch to using a locally-administered address, and add it to
the sandbox environment, like the others.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
CONFIG_VAL(DEBUG_UART_BASE) expands to CONFIG_DEBUG_UART_BASE or
CONFIG_SPL_DEBUG_UART_BASE or CONFIG_TPL_DEBUG_UART_BASE and allows boards
to set different values for SPL, TPL and U-Boot Proper.
For ns16550 driver this support is there since commit d293759d55
("serial: ns16550: Add support for SPL_DEBUG_UART_BASE").
Signed-off-by: Pali Rohár <pali@kernel.org>
The address where the device tree will be passed in to U-Boot at is now
moved to the Kconfig file. If this is user configurable, it needs to be
exposed rather than hidden, and should probably be renamed as well.
Reviewed-by: Rick Chen <rick@andestech.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_RELOC_TEXT_BASE
CONFIG_SPL_RELOC_STACK
CONFIG_SPL_RELOC_MALLOC_ADDR
CONFIG_SPL_RELOC_MALLOC_SIZE
Signed-off-by: Tom Rini <trini@konsulko.com>
- Make all users of CUSTOM_SYS_INIT_SP_ADDR reference SYS_INIT_SP_ADDR
- Introduce HAS_CUSTOM_SYS_INIT_SP_ADDR to allow for setting the stack
pointer directly, otherwise we use the common calculation.
- On some platforms that were using the standard calculation but did not
set CONFIG_SYS_INIT_RAM_SIZE / CONFIG_SYS_INIT_RAM_ADDR, set them.
- On a small number of platforms that were not subtracting
GENERATED_GBL_DATA_SIZE do so now via the standard calculation.
- CONFIG_SYS_INIT_SP_OFFSET is now widely unused, so remove it from most
board config header files.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_BSS_MAX_SIZE
CONFIG_SPL_MAX_FOOTPRINT
Note that the da850evm platforms were violating the "only use one" rule
here, and so now hard-code their BSS limit.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_INIT_MINIMAL
CONFIG_SPL_FLUSH_IMAGE
CONFIG_SPL_SKIP_RELOCATE
Signed-off-by: Tom Rini <trini@konsulko.com>
Enable OF_HAS_PRIOR_STAGE for ae350 boards with OF_BOARD
Fixes: 239d22c795 ("fdt: Enable OF_HAS_PRIOR_STAGE for most boards with OF_BOARD")
Signed-off-by: Rick Chen <rick@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
zynqmp:
- Fix DP PLL configuration for zcu102/zcu106 and SOM
- Fix split mode for starting R5s
- DT fixes
- Remove firmware node for mini configurations
- Wire TEE for multi DTB fit image
xilinx:
- Handle board_get_usable_ram_top(0) properly
phy:
- Extend psgtr timeout
mmc:
- Fix mini configuration which misses zynqmp_pm_is_function_supported()
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYo4bYwAKCRDKSWXLKUoM
IYmTAJ9t4GDXggJ7ErB3Kk7/qSrywjEGAgCgnKQVgQvjo1B6o5aiwbk1wR86zkQ=
=W7X8
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.07-rc4' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2022.07-rc4
zynqmp:
- Fix DP PLL configuration for zcu102/zcu106 and SOM
- Fix split mode for starting R5s
- DT fixes
- Remove firmware node for mini configurations
- Wire TEE for multi DTB fit image
xilinx:
- Handle board_get_usable_ram_top(0) properly
phy:
- Extend psgtr timeout
mmc:
- Fix mini configuration which misses zynqmp_pm_is_function_supported()
The bulk of it is (finally!) some DT sync from the kernel. We refrained
from syncing one incompatible change, as this would spoil booting Linux
kernels before v5.13 with U-Boot's DT (via UEFI, for instance).
I test booted Linux v5.18 and v5.4 with that new DT on some boards, and
the headless peripherals (MMC, USB, Ethernet) seemed to work.
The rest are fixes:
- silencing missing clock warnings due to the new pinctrl driver
- fixing "UART0 on PortF", allowing UART access through the SD card pins
- add an F1C100s clock driver, to enable MMC support (SPI comes later)
- some cleanups for CONS_INDEX_n in Kconfig
Tested on BananaPi-M1, Pine64-LTS, Pine-H64, X96-Mate (H616) and
OrangePi-Zero.
Currently, selecting UART0_PORT_F entirely disables MMC support on sunxi
platforms. But this is a bigger hammer then needed. Muxing UART0 to the
pins on port F only causes a conflict with MMC0, so minimize the impact
by specifically skipping MMC0 init. We can continue to use MMC1/2 if
those are enabled.
Let's also remove the preprocessor check while refacting this function.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Use the de10-nano files as templates for the de10-standard board.
The files in qts directory are generated by quartus from the GHRD
design.
Signed-off-by: Humberto Naves <hsnaves@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Move legacy spi_get_bus_and_cs() code to _spi_get_bus_and_cs().
Add new spi_get_bus_and_cs() implementation which rely on DT
for speed and mode and don't need any drv_name nor dev_name
parameters. This will prepare the ground for next patch.
Update all callers to use _spi_get_bus_and_cs() to keep the
same behavior.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Marek Behun <marek.behun@nic.cz>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefan Roese <sr@denx.de>
Cc: "Pali Rohár" <pali@kernel.org>
Cc: Konstantin Porotchkin <kostap@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Pratyush Yadav <p.yadav@ti.com>
Cc: Sean Anderson <seanga2@gmail.com>
Cc: Anji J <anji.jagarlmudi@nxp.com>
Cc: Biwen Li <biwen.li@nxp.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Chaitanya Sakinam <chaitanya.sakinam@nxp.com>
Add support for DH electronics i.MX8M Plus DHCOM SoM on PDK2 carrier board.
Currently supported are serial console, EQoS and FEC ethernets, eMMC, SD,
SPI NOR and USB 3.0 host.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Convert the board to DM I2C and DM RTC. This leads to removal of board
side iomuxc configuration, which is now done using pin control driver,
and conversion of board side legacy I2C accessors to DM ones.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Before this commit device tree selection could rely solely on
differentiating the iMX6 processor variant Q and DL. After adding two new
carrier boards, the DRC02 and the picoITX, the interchangeability of SoMs
makes this approach infeasible.
It is now required to specify the carrier board (dhcom-drc02,
dhcom-picoitx or dhcom-pdk2) at compile time using
CONFIG_DEFAULT_DEVICETREE. The SoM is determined at runtime as before.
Signed-off-by: Philip Oberfichtner <pro@denx.de>
In the DH electronics iMX6 board file fix the outdated eeprom path by
using a DT label instead.
The label has been newly created for all iMX6QDL DHCOM boards.
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Philip Oberfichtner <pro@denx.de>
