Commit graph

21485 commits

Author SHA1 Message Date
Patrice Chotard
a6d7eeb66d spi: stm32_qspi: Always check SR_TCF flags in stm32_qspi_wait_cmd()
Currently, SR_TCF flag is checked in case there is data, this criteria
is not correct.

SR_TCF flags is set when programmed number of bytes have been transferred
to the memory device ("bytes" comprised command and data send to the
SPI device).
So even if there is no data, we must check SR_TCF flag.

Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
2022-05-19 18:54:18 +02:00
Ashok Reddy Soma
e9869f474c phy: zynqmp: Increase timeout value to 10ms
Observing psgtr pll timeouts with some usb hubs and devices behind it.
Increase timeout to 10ms to take care of it.

Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/20220510131234.2650-1-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
2022-05-18 13:17:54 +02:00
Robert Marko
f9ec791b5e pinctrl: probe pinctrl drivers during post-bind
Currently, pinctrl drivers only get probed if pinconf is actually being
used, however on SoC-s like Armada 3720 pinctrl driver is a also the GPIO
driver.

So, if the pinctrl driver doesn't get probed GPIO-s won't get registered
and thus they cannot be used.

This is a problem on the Methode eDPU as it just uses SB pins as GPIO-s
and without them being registered networking won't work as it only has
one SFP slot and the TX disable GPIO is on the SB controller.

So, probe the pinctrl drivers using DM_FLAG_PROBE_AFTER_BIND like LED
uclass does.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
2022-05-17 06:44:06 +02:00
Pali Rohár
d293759d55 serial: ns16550: Add support for SPL_DEBUG_UART_BASE
Use CONFIG_VAL(DEBUG_UART_BASE) instead of CONFIG_DEBUG_UART_BASE, so
proper config value (CONFIG_DEBUG_UART_BASE or CONFIG_SPL_DEBUG_UART_BASE)
is used based on building target.

Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
2022-05-17 06:44:06 +02:00
Pali Rohár
958789f026 serial: Add new config option TPL_DEBUG_UART_BASE
TPL_DEBUG_UART_BASE is same as DEBUG_UART_BASE, but applies only for TPL.

Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Stefan Roese <sr@denx.de>
2022-05-17 06:44:06 +02:00
Pali Rohár
9f971ff714 serial: Add new config option SPL_DEBUG_UART_BASE
SPL_DEBUG_UART_BASE is same as DEBUG_UART_BASE, but applies only for SPL.

In some cases base address of UART is different in SPL and proper U-Boot.

Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
2022-05-16 11:31:34 +02:00
T Karthik Reddy
155353234e mmc: zynq_sdhci: Add weak function prototype
zynqmp_pm_is_function_supported() which checks feature support on som,
which is implemented in firmware_zynqmp.c driver. As mini configuration
does not use firmware driver, so create a weak function to avoid
compilation error on zynqmp mini configuration.

Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Acked-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/c60655a509956b8fc3a81671a7dc51157f3973db.1651048030.git.michal.simek@xilinx.com
2022-05-13 09:10:02 +02:00
Michal Simek
303198e26d soc: xilinx: zynqmp: fix out of bounds array access
The call to xilinx_pm_request requires an array of a larger size.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/5f1409de285d7454af171a54e5f115da9d82c44e.1650440343.git.michal.simek@xilinx.com
2022-05-13 09:10:02 +02:00
Jorge Ramirez-Ortiz
9b31e109b2 soc: xilinx: versal: fix out of bounds array access
The call to xilinx_pm_request requires an array of a larger size.

Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Link: https://lore.kernel.org/r/20220416181530.2311155-1-jorge@foundries.io
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2022-05-13 09:10:02 +02:00
Chris Packham
54a54a6313 Convert CONFIG_MTD_CONCAT to Kconfig
This converts the following to Kconfig:
  CONFIG_MTD_CONCAT

Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2022-05-11 09:22:24 -04:00
Tom Rini
21e25992c8 Add new STM32 MCU boards and Documentation
STM32 programmer improvements
 video: support several LTDC HW versions and fix data enable polarity
 board: fix stboard error message, consider USB cable connected when boot device is USB
 configs: stm32mp1: set console variable for extlinux.conf
 configs: stm32mp1: add support for baudrate higher than 115200 for ST-Link
 ARM: stm32mp: Fix Silicon version handling and ft_system_setup()
 phy: stm32-usbphyc: Add DT phy tuning support
 arm: dts: stm32mp15: alignment with v5.18
 ram: Conditionally enable ASR
 mach-stm32mp: psci: retain MCUDIVR, PLL3CR, PLL4CR, MSSCKSELR across suspend
 configs: Use TFTP_TSIZE on DHSOM and STMicroelectronics boards
 ARM: stm32: Use default CONFIG_TFTP_BLOCKSIZE on DHSOM
 pinctrl: stm32: rework GPIO holes management
 -----BEGIN PGP SIGNATURE-----
 
 iQJQBAABCgA6FiEEXyrViUccKBz9c35Jysd4L3sz/6YFAmJ6U4QcHHBhdHJpY2Uu
 Y2hvdGFyZEBmb3NzLnN0LmNvbQAKCRDKx3gvezP/pg4SEACFSVRcCa/7r2QXObqk
 mORtlp6OrZLfCQGMugv9Oj0W+L4nanJEZEJknhasoHgm5CyTuCGEm7qxgWWBKA9j
 yeCfcpToXrY4cIMgsPR4tpZ9jn4fLsHFBEvCVMEoOp/K2ZI27lfJ0/OeRlgKdg11
 dTmM+J96vw7ltLHeN+yRWY1XgaGsBreqNJSO2mCGrAbbTJXSTrNZxP4wonTvKkFI
 GyTIgRaQA9ggk7/IhalusEEGIF0aaaX/z7uBXqEGkCyOTacLG5rxYNGCoaPdv1Bl
 fT7spZy1bAx3ABq/yJeF38Wi5jCXf55Z3cwYK0+tpJVUlAncYpJJBiyTERtR24OK
 NeDTWkw4e071xPDfmUFB96eINDQ8KXBRRcK2n2b6nW43loYtqgafrx4prL8W2T/u
 mB1WquNwjqdNN43iKAcyArrooOG18sJzRE3uAM6W4fjPx8DAHtYdaO3du3Mb5Kzz
 YaqgVO88NDsYaQRJCnmdQ7KDFToMy5A6btj2LhnYQ/3CMhktkg2RHC0aERGgNJLs
 ifVj3kvc+l8UwomvNOMjNket+AH7hbp64lbAfjAwzcgOGROKNyOslsr33qibg4lQ
 SQKl15wFDHLAcP2tj9QoUFO+97FqDXWBIzoEhDDBqfpVNRx25R7NePUkkA+0dHTS
 VedeNG6p2yFeW2UTAD4nYP9xWA==
 =s7xn
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-stm32-20220510' of https://source.denx.de/u-boot/custodians/u-boot-stm

Add new STM32 MCU boards and Documentation
STM32 programmer improvements
video: support several LTDC HW versions and fix data enable polarity
board: fix stboard error message, consider USB cable connected when boot device is USB
configs: stm32mp1: set console variable for extlinux.conf
configs: stm32mp1: add support for baudrate higher than 115200 for ST-Link
ARM: stm32mp: Fix Silicon version handling and ft_system_setup()
phy: stm32-usbphyc: Add DT phy tuning support
arm: dts: stm32mp15: alignment with v5.18
ram: Conditionally enable ASR
mach-stm32mp: psci: retain MCUDIVR, PLL3CR, PLL4CR, MSSCKSELR across suspend
configs: Use TFTP_TSIZE on DHSOM and STMicroelectronics boards
ARM: stm32: Use default CONFIG_TFTP_BLOCKSIZE on DHSOM
pinctrl: stm32: rework GPIO holes management
2022-05-10 15:28:02 -04:00
Tom Rini
b4eb577663 Merge tag 'i2c-2022-07' of https://source.denx.de/u-boot/custodians/u-boot-i2c
i2c changes for 2022.07

- i2c: ihs: intel: Fix typo in comments
  Patch from Michal

- misc: atsha204a: Add support for atsha204 chip
  from Pali
2022-05-10 09:52:00 -04:00
Sean Anderson
381277410d misc: Fix always compiling MISC even for SPL/TPL
We should only build support for misc if the appropriate SPL/TPL symbol
is defined. To ease the transition, make SPL/TPL_MISC default to MISC.
This is necessary because many drivers don't specify their dependencies
properly. These defaults can be removed once all drivers depend on the
appropriate config.

Fixes: aaba703fd0 ("spl: misc: Allow misc drivers in SPL and TPL")
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
[trini: Add VPL_MISC symbol, handle like SPL/TPL_MISC]
Signed-off-by: Tom Rini <trini@konsulko.com>
2022-05-10 09:51:50 -04:00
Marek Vasut
05a3a028c1 clk: stm32mp1: Add missing newline
Add missing newline to this debug message, no functional change.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
2022-05-10 13:56:11 +02:00
Patrice Chotard
da6473c0d4 phy: stm32-usbphyc: stm32-usbphyc: Add DT phy tuning support
Add support of phy-tuning properties for sm32-usbphyc's phy tuning
aligned with v5.15 kernel bindings.

Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
2022-05-10 13:56:07 +02:00
Patrice Chotard
427f452cb9 gpio: stm32_gpio: Rework GPIO hole management
On some STM32 SoC's package, GPIO bank may have hole in their GPIO bank
Example:
  If GPIO bank have 16 GPIO pins [0-15].
  In particular SoC's package case, some GPIO bank can have less GPIO pins:
    - [0-10] => 11 pins;
    - [2-7] => 6 pins.

Commit dbf928dd26 ("gpio: stm32f7: Add gpio bank holes management")
proposed a first implementation by not counting GPIO "inside" hole. GPIO
are not displaying correctly using gpio or pinmux command when GPIO holes
are located at the beginning of GPIO bank.

To simplify, consider that all GPIO have 16 GPIO and use the gpio_ranges
struct to indicate if a GPIO is mapped or not. GPIO uclass offers several
GPIO functions ("input", "output", "unused", "unknown" and "func"), use
"unknown" GPIO function to indicate that a GPIO is not mapped.

stm32_offset_to_index() is no more needed and removed.

This must be reflected using the "gpio" command to indicate to user
that a particular GPIO is not mapped (marked as "unknown") as shown below:

Example for a 16 pins GPIO bank with the [2-7] mapping (only 6 pins
mapped):
GPIOI0          : unknown
GPIOI1          : unknown
GPIOI2          : analog
GPIOI3          : analog
GPIOI4          : alt function 0 push-pull pull-down
GPIOI5          : alt function 0 push-pull pull-down
GPIOI6          : alt function 0 push-pull pull-down
GPIOI7          : analog
GPIOI8          : unknown
GPIOI9          : unknown
GPIOI10         : unknown
GPIOI11         : unknown
GPIOI12         : unknown
GPIOI13         : unknown
GPIOI14         : unknown
GPIOI15         : unknown

Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
2022-05-10 13:54:48 +02:00
Patrice Chotard
234b03f3a9 pinctrl: pinctrl_stm32: Use GPIOF_UNKNOWN to indicate not mapped pins
GPIOF_UNKNOWN becomes a valid pin muxing information to indicate
that a pin is not mapped.

Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
2022-05-10 13:54:48 +02:00
Patrice Chotard
4382e55c42 pinctrl: pinctrl_stm32: Update pinmux_mode definition
pinmux_mode[] is linked to gpio_function[] defined in gpio-uclass.c
So reuse the same gpio_func_t enum value

Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
2022-05-10 13:54:48 +02:00
Marek Vasut
221869efc3 ram: stm32mp1: Conditionally enable ASR
Enable DRAM ASR, auto self-refresh, conditionally, based on DT PWRCTL
register bits. While ASR does save considerable amount of power at
runtime automatically, it also causes LTDC underruns on large panels.
Let user select whether or not ASR is required or not, generally ASR
should be enabled on portable and battery operated devices.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
2022-05-10 13:54:47 +02:00
Yannick Fertre
13dc7562b6 video: stm32: stm32_ltdc: support several hardware versions
Register mapping & pixel formats depend on version of ltdc
display controller.

Signed-off-by: Yannick Fertre <yannick.fertre@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
2022-05-10 10:56:39 +02:00
Yannick FERTRE
ef4ce6df32 video: stm32: stm32_ltdc: fix data enable polarity
Wrong DISPLAY_FLAGS used to set the data enable polarity.

Signed-off-by: Yannick FERTRE <yannick.fertre@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
2022-05-10 10:56:39 +02:00
Pali Rohár
89eabd2f35 misc: atsha204a: Add support for atsha204 chip
atsha204 chip is predecessor of atsha204a chip. Current U-Boot driver
atsha204a-i2c.c can use both atsha204 and atsha204a chips because it does
not call specific functions to just one of these chips.

So just add compatible string for atsha204.

Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
2022-05-10 06:48:05 +02:00
Michal Simek
a6cc0b082f i2c: ihs: intel: Fix typo in comments (actual)
s/actucal/actual/g

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
2022-05-10 06:47:13 +02:00
Neil Armstrong
411502ccb8 regulator: add driver for the TPS65219 BUCK & LDO regulators
The TPS65219 I2S PMIC features 3 Buck converters and 4 linear regulators,
2 GPOs, 1 GPIO, and 3 multi-function-pin.

This adds the driver for the Buck converters & linear regulators.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2022-05-09 13:40:24 -04:00
Neil Armstrong
b5cfa0c7ca power: add driver for the TPS65219 PMIC
The TPS65219 I2S PMIC features 3 Buck converters and 4 linear regulators,
2 GPOs, 1 GPIO, and 3 multi-function-pin.

This adds the PMIC driver, loading the regulator sub-nodes.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2022-05-09 13:40:24 -04:00
Tom Rini
145921bdbd Merge https://source.denx.de/u-boot/custodians/u-boot-usb 2022-05-06 08:57:15 -04:00
Patrice Chotard
6aa8bde878 usb: host: ehci-generic: Remove DM_REGULATOR flag
Since commit 16cc5ad0b4 ("power: regulator: add dummy helper")
regulator dummy helper are always available even if DM_REGULATOR
is not set.
DM_REGULATOR flag is no more needed to protect no DM core,
remove it.

Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
2022-05-06 10:38:39 +02:00
Patrice Chotard
ba96176ab7 usb: host: ehci-generic: Make usage of clock/reset bulk() API
Make usage of clock and reset bulk API in order to simplify the code

Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
2022-05-06 10:38:39 +02:00
Pali Rohár
0a095fc53b watchdog: Add MAX6370 watchdog timer driver
MAX6370 watchdog is available e.g. on Freescale P1/P2 RDB-PC boards.

Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
2022-05-06 07:06:51 +02:00
Pali Rohár
aa5ea20c71 misc: fs_loader: Fix compile warnings when CONFIG_CMD_UBIFS is enabled
drivers/misc/fs_loader.c: In function ‘mount_ubifs’:
drivers/misc/fs_loader.c:46:12: warning: implicit declaration of function ‘ubi_part’ [-Wimplicit-function-declaration]
  int ret = ubi_part(mtdpart, NULL);
            ^~~~~~~~
drivers/misc/fs_loader.c:53:9: warning: implicit declaration of function ‘cmd_ubifs_mount’ [-Wimplicit-function-declaration]
  return cmd_ubifs_mount(ubivol);
         ^~~~~~~~~~~~~~~
drivers/misc/fs_loader.c: In function ‘umount_ubifs’:
drivers/misc/fs_loader.c:58:9: warning: implicit declaration of function ‘cmd_ubifs_umount’ [-Wimplicit-function-declaration]
  return cmd_ubifs_umount();
         ^~~~~~~~~~~~~~~~

Signed-off-by: Pali Rohár <pali@kernel.org>
2022-05-05 19:37:11 -04:00
Marek Vasut
0be4b0b651 reset: Return 0 if ops unimplemented and remove empty functions
In case the ops is not implemented, return 0 in the core right away.
This is better than having multiple copies of functions which just
return 0 in each reset driver. Drop all those empty functions.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
2022-05-05 19:37:11 -04:00
Heinrich Schuchardt
d657766819 clk: scmi: fix scmi_clk_get_attibute()
Local variable out.name lives on the stack and therefore cannot
be returned directly. Move the strdup() call into the function.
(Coverity 352460)

Fixes: 7c33f78983 ("clk: scmi: register scmi clocks with CCF")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
2022-05-05 19:37:11 -04:00
Oliver Graute
8b42439ad1 rtc: rv8803: fix off-by-one in month counting
tm_mon has a range from 0..11, but the RTC expects 1..12. So we adapt
the month accordingly. This was determined when comparing the driver
with the corresponding linux kernel driver.

Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Heiko Schocher <hs@denx.de>
2022-05-05 15:06:02 -04:00
Sean Anderson
bfae2744dd serial: smh: Check return value of strndup
strndup can fail. Check for it.

Fixes: 4855b39be ("serial: smh: Implement puts for DM")
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
2022-05-05 15:06:02 -04:00
Stanley Chu
344e86c61e gpio: npcm: Add support for Nuvoton NPCM SoCs
Add Nuvoton BMC NPCM7xx/NPCM8xx gpio driver

Signed-off-by: Stanley Chu <yschu@nuvoton.com>
2022-05-05 09:29:58 -04:00
Sam Shih
1a80ef5520 pinctrl: mediatek: add support for different types of IO pins
There are many pins in an SoC, and register usage may vary by pins.
This patch introduces a concept of "io type" and "io type group"
to mediatek pinctrl drivers. This can provide different pinconf
handlers implementation (eg: "bias-pull-up/down", "driving" and
"input-enable") for IO pins that belong to different types.

Signed-off-by: Sam Shih <sam.shih@mediatek.com>
2022-05-05 09:29:58 -04:00
Sam Shih
10334e0bc8 pinctrl: mediatek: introduce multiple memory bases support
Pinctrl design of some mediatek SoC need to access registers that
distribute in multiple memory base address. this patch introduce new
mechanism in mediatek pinctrl driver to support the chips which have
the new design.

This patch add a member 'base_calc' in pinctrl private data, and changed
original 'base' private data to an array of *iomem.

When 'base_calc' attribute is set, it will requests multiplue regs base
from the DT, if 'base_calc' attribute is not set, it only use legacy way
to request single reg resource from the DT.

Signed-off-by: Sam Shih <sam.shih@mediatek.com>
2022-05-05 09:29:58 -04:00
Sam Shih
dafe0fbfb0 pinctrl: mediatek: rewrite mtk_pinconf_set and related functions
There are many pins in a SoCs, and different pin may belong
to different "io_type", For example: some pins of MT7622 belongs
to "io_type A", the other belongs to "io_type B", and pinctrl "V0"
means handle pinconf via "io_type A" or "io_type B", so SoCs that
contain "io_type A" and "io_type B" pins, use "V0" in pinctrl driver.

This patch separates the implementation of register operations
(e.g: "bias-pull-up/down", "driving" and "input-enable") into
different functions, and lets the original V0/V1
ops to call the new functions.

Signed-off-by: Sam Shih <sam.shih@mediatek.com>
2022-05-05 09:29:57 -04:00
Jim Liu
b789e4f215 timer: npcm: Add NPCM timer support
Add Nuvoton BMC NPCM7xx/NPCM8xx timer driver.

Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
Signed-off-by: Stanley Chu <yschu@nuvoton.com>
2022-05-05 09:28:47 -04:00
Jim Liu
6f6a0b74d6 serial: npcm: Add support for Nuvoton NPCM SoCs
Add Nuvoton BMC NPCM7xx/NPCM8xx uart driver

Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
Signed-off-by: Stanley Chu <yschu@nuvoton.com>
2022-05-05 09:28:47 -04:00
Jim Liu
c7554574ff clk: nuvoton: Add support for NPCM750
Add clock controller driver for NPCM750

Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
Signed-off-by: Stanley Chu <yschu@nuvoton.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
2022-05-05 09:28:47 -04:00
Tom Rini
1739a6db54 Pull request for efi-2022-07-rc2-2
* Test
   Unit test for 'bootmenu' command
 
 * UEFI
   Preparatory patches for implementing a UEFI boot options based menu
 -----BEGIN PGP SIGNATURE-----
 
 iQIzBAABCAAdFiEEbcT5xx8ppvoGt20zxIHbvCwFGsQFAmJyoMcACgkQxIHbvCwF
 GsTbjA/+J+mQg5Rl8AkWwxnBynshNbOsQjsekJjoQTKN9XdvA4Rest2cP7AZ7LP7
 yi2jks4qMKex5NyGSt2wV51snwZJ6ikZshYpEl59wzoOa4DNlBktH/emOVPNhHqm
 n+By+m1Uer7I1NBATfGLjgp7Pwk910OkX9sXdFBtg3OlQwBnoCgNARmxxz7ifWwa
 BxZP2w7l8BfejeZyS/HBzvUc8tPHljukidZoXANXJ/wbJmiU1JR+MBU4+iJmAwCi
 rt4loje8ynIiPd0NsfDdasqsNGXNtKf1ikY9xH7UBmv8lmkM1BLE+SSufb+8ihUV
 5/hn4Q/nXze4klNM/owkglfsiBzs1tGIh1EBmuD9BBjBKKTHMUqSCU1f30cqc+oh
 80heH8J6GicqlQlaN5WyYbimH7WvGz48dr8VrWM5AuFf8FjZlNfIlkt86h4yQBjc
 v6aTvNOXyLriFUh1p9DaQi1+U2ZdB2UO7wpEuWdVbgTE/yH9ZqmBNCB8kGTH1TPk
 pOwMDZPIFTvHp3WirztpxZRcPus/Eo7s1noMGzM/gdQjmIMRlkEbP8T617hoXWdZ
 /T4xwRyArQFCkx5xhd5nNqpLd3Lgq4ezpw5ZFAmULJZaGYpp6Iaf+IWiTYghrZ2/
 z5cfeQZVL7Sb7vb/yajtVdaZzKg8Eq1FeZdDnoBayvL9UdFTBWA=
 =bl7A
 -----END PGP SIGNATURE-----

Merge tag 'efi-2022-07-rc2-2' of https://source.denx.de/u-boot/custodians/u-boot-efi

Pull request for efi-2022-07-rc2-2

* Test
  Unit test for 'bootmenu' command

* UEFI
  Preparatory patches for implementing a UEFI boot options based menu
2022-05-04 12:08:40 -04:00
Tom Rini
c3d451d5e6 Merge https://source.denx.de/u-boot/custodians/u-boot-marvell
- mips: octeon: Add ethernet support (Aaron & Stefan)
- Misc mvneta changes, cleanups, fixes (Marek)
2022-05-04 09:05:03 -04:00
Tom Rini
4209f74445 Merge branch 'master' of https://source.denx.de/u-boot/custodians/u-boot-spi
- NPCM7xx FIU SPI driver (Jim Liu)
- AT45DB641E dataflash (Luca Ellero)
2022-05-04 09:04:43 -04:00
Marek Behún
95a3a6ee08 net: mvneta: Drop unneeded macro
Macro MVNETA_GMAC_FORCE_LINK_UP can be dropped from value assignment in
fixed link case, since it's value is written into the register later in
the function for link-down-to-link-up case. The value is written as
MVNETA_GMAC_FORCE_LINK_DOWN | MVNETA_GMAC_FORCE_LINK_PASS, and so the
macro definition can also be dropped.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2022-05-04 07:05:51 +02:00
Marek Behún
bdbda1e826 net: mvneta: Disable fixed PHY code if PHY_FIXED is not compiled in
Guard the code handling the fixed PHY case by
CONFIG_IS_ENABLED(PHY_FIXED).

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2022-05-04 07:05:51 +02:00
Marek Behún
38332211e3 net: mvneta: Drop fixed_link member from private struct
Since this member is checked only at two places drop it and inline it's
usage.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2022-05-04 07:05:51 +02:00
Marek Behún
e06c7f34d2 net: mvneta: Write PHY address just before enabling HW polling
Write PHY address just before enabling HW polling of the PHY.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2022-05-04 07:05:51 +02:00
Marek Behún
77fcf3cf12 net: mvneta: Convert to use PHY_FIXED for fixed-link
Stop parsing fixed-link in the MAC driver. Instead support only PHY mode
and let the fixed PHY driver handle the fixed-link case.

Enable CONFIG_PHY_FIXED for mvneta boards that need it: Turris Omnia and
ESPRESSObin.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2022-05-04 07:05:51 +02:00
Marek Behún
31f4ccca0a net: mvneta: Rename CONFIG_NR_CPUS to MVNETA_NR_CPUS
The CONFIG_* macros are reserved for Kconfig. This was probably done
when this driver was being imported from Linux. Rename the macro.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2022-05-04 07:05:51 +02:00
Marek Behún
730dad9919 net: mvneta: Don't check for CONFIG_PHYLIB
Drop checking for CONFIG_PHYLIB in mvneta, this is already done in
Kconfig.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2022-05-04 07:05:51 +02:00
Marek Behún
824f2f9cd9 net: mvneta: Drop unnecessary space
Drop unnecessary space in mvneta_adjust_link().

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2022-05-04 07:05:51 +02:00
Marek Behún
3b38fad182 net: mvneta: Use bool instead of int for boolean variable
Use the bool type instead of int for status_change variable.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2022-05-04 07:05:51 +02:00
Marek Behún
ca4730a466 net: mvneta: Drop one indentation level in mvneta_adjust_link()
Drop one indentation level in the mvneta_adjust_link() function.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2022-05-04 07:05:51 +02:00
Marek Behún
7ec50404ae net: mvneta: Fix unused variable warning if DM_GPIO is disabled
The `ret` variable in mvneta_probe() is unused if DM_GPIO is disabled.

Since the variable is used only once after assigning value, we can
inline the usage and drop the variable.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2022-05-04 07:05:51 +02:00
Marek Behún
1d87904c15 net: mvneta: Don't register MDIO bus
This MDIO bus is now handled by a proper mvmdio DM driver. Remove it
from mvneta.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2022-05-04 07:05:51 +02:00
Marek Behún
4d47ea2279 net: mvneta: Remember fixed link instead of PHY address in priv data
We don't need to remember PHY address anymore, because since using DM
MDIO for connecting PHY, the address is parsed by mdio-uclass from
the ofnode.

But the driver uses a special value of the address to signal fixed link
usage.

Drop phyaddr add fixed_link in driver private structure. This simplifies
code a little.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2022-05-04 07:05:51 +02:00
Marek Behún
da84e409df net: mvneta: Use DM MDIO API for connecting PHY
Use the modern DM MDIO API for connecting PHY in the mvneta driver.

This requires enabling MVMDIO driver in several config files.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2022-05-04 07:05:51 +02:00
Marek Behún
47f0e8e21a net: mvneta: Fix 10Mbps speed
In mvneta_adjust_link() we need to set MII_SPEED bit only if PHY reports
the speed at 100Mbps.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2022-05-04 07:05:51 +02:00
Marek Behún
443cf35674 net: mvneta: Get rid of platdata
Drop .of_to_plat() from the mvneta driver and parse the two properties
in .probe().

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2022-05-04 07:05:51 +02:00
Stefan Roese
8e0f8efe2a net: Add ethernet support for MIPS Octeon
This patchs adds the ethernet & MDIO driver for the MIPS Octeon II / III
SoC platform. Please note that these drivers are based on the 2013
U-Boot version from Marvell and make use of the platform supported
helper functions for the ethernet functionality, including stuff like
SFP handling.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
2022-05-04 03:38:21 +02:00
Andrew Scull
3b92018675 pci: Add config for Enhanced Allocation
Add a config to control whether Enhanced Allocation is supported by the
driver.

Signed-off-by: Andrew Scull <ascull@google.com>
2022-05-03 18:33:29 -04:00
Andrew Scull
0699a78c0c virtio: pci: Make use of dm_pci_map_bar()
The virtio PCI capabilities describe regions of memory that should be
mapped. Map those with dm_pci_map_bar() which will ensure they are valid
PCI regions.

Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2022-05-03 18:33:29 -04:00
Andrew Scull
c763e1e023 virtio: pci: Check virtio configs are mapped
Prepare for calls to `virtio_pci_map_capability()` failing by returning
NULL on error. If this happens, later accesses to the pointers would be
unsafe so cause the probe to fail if such an error occurs.

Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2022-05-03 18:33:29 -04:00
Andrew Scull
2635e3b50f pci: Add mask parameter to dm_pci_map_bar()
Add a mask parameter to control the lookup of the PCI region from which
the mapping can be made.

Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2022-05-03 18:33:29 -04:00
Andrew Scull
a822d1dee4 pci: Update dm_pci_bus_to_virt() parameters
Add mask parameter and reorder length parameter to match the other PCI
address conversion functions. Using PCI_REGION_TYPE as the mask gives
the old behaviour.

It's converted from a macro to an inline function as the length
parameter is now used twice, but should only be calculated once.

Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2022-05-03 18:33:29 -04:00
Andrew Scull
7739d93d82 pci: Match region flags using a mask
When converting addresses, apply a mask to the region flags during
lookup. This allows the caller to specify which flags are important and
which are not, for example to exclude system memory regions.

The behaviour of the function is changed such that they don't
preferentially search for a non-system memory region. However, system
memory regions are added after other regions in decode_regions() leading
to a similar outcome.

Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2022-05-03 18:33:26 -04:00
Andrew Scull
12507a2d22 pci: Map bars with offset and length
Evolve dm_pci_map_bar() to include an offset and length parameter. These
allow a portion of the memory to be mapped and range checks to be
applied.

Passing both the offset and length as zero results in the previous
behaviour and this is used to migrate the previous callers.

Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2022-05-03 15:50:46 -04:00
Andrew Scull
398dc367c5 pci: Range check address conversions
When converting between PCI bus and physical addresses, include a length
parameter that can be used to check that the entire range fits within
one of the PCI regions. This prevents an address being returned that
might be only partially valid for the range it is going to be used for.

Where the range check is not wanted, passing a length of 0 will have the
same behaviour as before this change.

Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2022-05-03 15:50:45 -04:00
Andrew Scull
ec8eba8c2d pci: Check region ranges are addressable
When parsing the `ranges` DT node, check that both extremes of the
regions are addressable without overflow. This assumption can then be
safely made when processing the regions.

Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2022-05-03 15:50:45 -04:00
Andrew Scull
60f4142aa2 pci: Fix use of flags in dm_pci_map_bar()
The flags parameter of dm_pci_map_bar() is used for PCI region flags
rather than memory mapping flags. Fix the type to match that of the
region flags and stop using the regions flags as memory mapping flags.

Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2022-05-03 15:50:45 -04:00
Andrew Scull
e7870c2cdc virtio: pci: Read entire capability into memory
Read the virtio PCI capability out of the device configuration space to
a struct rather than accessing fields directly from the configuration
space as they are needed. This both makes access to the fields easier
and avoids re-reading fields.

Re-reading fields could result in time-of-check to time-of-use problems,
should the value in the configuration space change. The range check of
the `bar` field and the later call to `dm_pci_read_bar32()` is an
example of where this could happen.

Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2022-05-03 15:50:45 -04:00
Andrew Scull
6a8cb878a2 virtio: pci: Check virtio capability is in bounds
Ensure the virtio PCI capabilities are contained within the bounds of
the device's configuration space. The expected size of the capability is
passed when searching for the capability to enforce this check.

Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2022-05-03 15:50:45 -04:00
Andrew Scull
f2c1ef1b6d virtio: pci: Check virtio common config size
Check that the common config is at least as large as the struct it is
expected to contain. Only then is it safe to cast the pointer and be
safe from out-of-bounds accesses.

Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2022-05-03 15:50:45 -04:00
Andrew Scull
c690f64f4c virtio: pci: Bounds check notification writes
Make sure virtio notifications are written within their allocated
buffer.

Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2022-05-03 15:50:45 -04:00
Andrew Scull
94b28b9158 virtio: pci: Bounds check device config access
The device config is optional, so check it was present and mapped before
trying to use the pointer. Bounds violations are an error, not just a
warning, so bail if the checks fail.

Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2022-05-03 15:50:45 -04:00
Andrew Scull
da03cdfa7a virtio: pci: Fix discovery of device config length
The length of the device config was erroneously being taken from the
notify capability. Correct this by finding the length in the device
capability.

Fixes: 550435edf8 ("virtio: pci: Support non-legacy PCI transport device")
Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2022-05-03 15:50:45 -04:00
Andrew Scull
30471d5351 virtio: pci: Allow exclusion of legacy driver
Add a new config to control whether the driver for legacy virtio PCI
devices is included in the build. VIRTIO_PCI_LEGACY is included by
default when VIRTIO_PCI is selected, but it can also be independently
toggled.

Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2022-05-03 15:50:45 -04:00
Heinrich Schuchardt
d30924f16b lib: fix selection of CONFIG_CHARSET
lib/charset.c is not optional for
EFI_APP || EFI_LOADER || UFS || UT_UNICODE.
These must select CONFIG_CHARSET.

Fixes: 726cd9836d ("efi: Make unicode printf available to the app")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
2022-05-03 21:39:22 +02:00
Luca Ellero
c62f93a620 sf: dataflash: add support for AT45DB641E
NOTE: this chip uses "extened device information"

Signed-off-by: Luca Ellero <l.ellero@asem.it>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2022-05-03 17:57:19 +05:30
Luca Ellero
1c1c581d56 sf: dataflash: add support for "extended ID"
Take as reference Linux kernel code:
	drivers/mtd/devices/mtd_dataflash.c
	commit 1da8869a428317a6d3cd8d47184cf87feb34a98b
	Author: Andrey Smirnov <andrew.smirnov@gmail.com>

Signed-off-by: Luca Ellero <luca.ellero@brickedbrain.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2022-05-03 17:56:16 +05:30
Jim Liu
aaf2dbc82b spi: npcm-fiu: add NPCM7xx FIU controller driver
Add Nuvoton NPCM BMC Flash Interface Unit(FIU) SPI master
controller driver using SPI-MEM interface.

The FIU supports single, dual or quad communication interface.
The FIU controller driver provides flash access in UMA(User
Mode Access) mode by using an indirect address/data mechanism.

the dts node is followed upstream kernel dts name.

Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
Signed-off-by: Stanley Chu <yschu@nuvoton.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
[Jagan: fixed the Kconfig, Makefile order]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2022-05-03 17:49:48 +05:30
Tien Fong Chee
f9b9641348 mtd: spi-nor-ids: add Macronix mx25u51245g flash entry
Add Macronix mx25u51245g flash entry, so this can be used on
SoCFPGA devices.

Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
[Jagan: updated commit head]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2022-05-03 17:37:39 +05:30
Marek Vasut
1aa60f0cea mtd: spi-nor-ids: Add Winbond W25Q128JW ID
Add ID for Winbond W25Q128JW device. This is a 128 Mbit QSPI NOR.
Tested on W25Q128JWPIM part.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Horatiu Vultur <horatiu.vultur@microchip.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Vignesh R <vigneshr@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2022-05-03 17:35:17 +05:30
Tom Rini
edb6982b58 Merge branch '2022-05-02-add-verifying-program-loader'
To quote the author:

U-Boot provides a verified-boot feature based around FIT, but there is
no standard way of implementing it for a board. At present the various
required pieces must be built up separately, to produce a working
implementation. In particular, there is no built-in support for selecting
A/B boot or recovery mode.

This series introduces VPL, a verified program loader phase for U-Boot.
Its purpose is to run the verified-boot process and decide which SPL
binary should be run. It is critical that this decision happens before
SPL runs, since SPL sets up SDRAM and we need to be able to update the
SDRAM-init code in the field.

Adding VPL into the boot flow provides a standard place to implement
verified boot. This series includes the phase itself, some useful Kconfig
options and a sandbox_vpl build for sandbox. No verfied-boot support is
provided in this series.

Most of the patches in this series are fixes and improvements to docs and
various Kconfig conditions for SPL.
2022-05-02 19:02:44 -04:00
Simon Glass
747093dd40 vpl: Add Kconfig options for VPL
Add VPL versions of commonly used Kconfig options.

Signed-off-by: Simon Glass <sjg@chromium.org>
2022-05-02 09:58:13 -04:00
Simon Glass
f86ca5ad8f Introduce Verifying Program Loader (VPL)
Add support for VPL, a new phase of U-Boot. This runs after TPL. It is
responsible for selecting which SPL binary to run, based on a
verified-boot process.

Signed-off-by: Simon Glass <sjg@chromium.org>
2022-05-02 09:58:13 -04:00
Tony Dinh
f0f98758ed net: marvell: mvgbe: Set PHY page 0 before phy_connect
For most Kirkwood boards, the PHY page is already set to page 0
(in register 22) before phy_connect is invoked. But some board like
the Zyxel NSA310S (which uses the network chip MV88E1318S), the PHY page
is not set to page 0. There seems to be some bad data remained in
register 22 when the uclass MVGBE about to invoke phy_connect().

This patch enables the uclass MVGBE to always set the PHY page to 0
before phy_connect.

For reference, please see this discussion:
[RFC PATCH v2] arm: kirkwood: nsa310s: Use Marvell uclass mvgbe
and PHY driver for DM Ethernet.
https://lists.denx.de/pipermail/u-boot/2022-April/480946.html

This patch has been tested with the following Kirkwood boards:

NSA310S (88F6702, network chip MV88E1318S)
Sheevaplug (88F6281, network chip MV88E1318)
Pogo V4 (88F6192, network chip 88E1116R)
GF Home(88F6281, network chip 88E1116R)
Dreamplug (88F6281, network chip MV88E1318)
Dell Kace M300 (88F6282, network chip MV88E1318) - out of tree u-boot

Signed-off-by: Tony Dinh <mibodhi@gmail.com>
2022-05-02 07:47:26 +02:00
Andrew Scull
49209da54f sound: Fix buffer overflow in square wave generation
Data is written for each channel but is only tracked as having one
channel written. This resulted in a buffer overflow and corruption of
the allocator's metadata which caused further problems when the buffer
was later freed. This could be observed with sandbox unit tests.

Resolve the overflow by tracking the writes for each channel.

Fixes: f987177db9 ("dm: sound: Use the correct number of channels for sound")
Signed-off-by: Andrew Scull <ascull@google.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
2022-04-29 11:11:36 -04:00
Andrew Scull
beb341ae7f usb: sandbox: Bounds check read from buffer
The buffer is 512 bytes but read requests can be 800 bytes. Limit the
request to the size of the buffer.

Signed-off-by: Andrew Scull <ascull@google.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
2022-04-29 11:11:36 -04:00
Andrew Scull
62120155b6 usb: sandbox: Check for string end in copy_to_unicode()
When copying the string in copy_to_unicode(), check for the null
terminator in each position, not just at the start, to avoid reading
beyond the end of the string.

Signed-off-by: Andrew Scull <ascull@google.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
2022-04-29 11:11:36 -04:00
Andrew Scull
9c2f5ecd43 x86: sandbox: Add missing PCI bar to barinfo
There are expecte to be bars 0 through 5, but the last of these was
missing leading to an read beyond the buffer. Add the missing element
with zero values.

Signed-off-by: Andrew Scull <ascull@google.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2022-04-29 11:11:36 -04:00
Marek Vasut
69245e406e led: Drop led_default_state()
This function is empty, drop it.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Sean Anderson <seanga2@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Steven Lawrance <steven.lawrance@softathome.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
2022-04-28 09:26:44 -04:00
Marek Vasut
0107469780 led: gpio: Use NOP uclass driver for top-level node
The top level DT node of gpio-leds is not a LED itself, bind NOP uclass
driver to it, and bind different LED uclass driver to its subnodes which
represent the actual LEDs. This simplifies the probe() implementation
and fixes the bogus top-level not-an-LED in 'led list' command output:

```
=> led list
led             Error -121 <--- This is removed/fixed by this patch
green:user0     off
```

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Sean Anderson <seanga2@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Steven Lawrance <steven.lawrance@softathome.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
2022-04-28 09:26:43 -04:00
Marek Vasut
e3aa76644c led: gpio: Check device compatible string to determine the top level node
Since 2d1deaf88e ("led: gpio: Drop duplicate OF "label" property parsing"),
all LED nodes have some sort of label. Use device_is_compatible(..."leds-gpio")
to determine whether this is a top-level node, since it is only the top
level node which is compatible with "leds-gpio", the GPIO LEDs subnodes
are not.

Fixes: 2d1deaf88e ("led: gpio: Drop duplicate OF "label" property parsing")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Sean Anderson <seanga2@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Steven Lawrance <steven.lawrance@softathome.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
2022-04-28 09:26:43 -04:00
Marek Vasut
c438866b16 led: Mark device instance with DM_FLAG_PROBE_AFTER_BIND
Calling device_probe() from uclass .post_bind() callback has all kinds
of odd side-effects, e.g. device instances not being available just yet.
Make use of the DM_FLAG_PROBE_AFTER_BIND instead, mark device instances
which need to be probe()d in order to configure the LED default state
with this flag and let the DM core do the device_probe() at the right
time instead.

Fixes: 72675b063b ("led: Configure LED default-state on boot")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Sean Anderson <seanga2@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Steven Lawrance <steven.lawrance@softathome.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
2022-04-28 09:26:43 -04:00
Marek Vasut
9cc32bfa49 dm: core: Add DM_FLAG_PROBE_AFTER_BIND flag
Introduce DM_FLAG_PROBE_AFTER_BIND flag, which can be set by driver or
uclass in .bind(), to indicate such driver instance should be probe()d
once binding of all devices is complete.

This is useful in case the driver determines that hardware initialization
is mandatory on boot, and such initialization happens only in probe().
This also solves the inability to call device_probe() from .bind().

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Sean Anderson <seanga2@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Steven Lawrance <steven.lawrance@softathome.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
2022-04-28 09:26:43 -04:00
Tom Rini
8b2b125e95 Merge https://gitlab.denx.de/u-boot/custodians/u-boot-mpc85xx
fsl-qoriq: Fixes and updates on fsl-layerscape
mpc85xx: fixes and code cleanup
2022-04-27 09:19:41 -04:00
Tom Rini
24df831cd4 - Add AXG support for SARADC, including minimal ao-clk driver
- Update Amlogic documentation for Matrix & Jethub D1
 -----BEGIN PGP SIGNATURE-----
 
 iQIzBAABCgAdFiEEPVPGJshWBf4d9CyLd9zb2sjISdEFAmJo84YACgkQd9zb2sjI
 SdGgew//SPy7itxbFghfDXsRCA21W9potZQiL+Mpu3KmkYsGJ9l3axj8EAj/5VE6
 /We80jschGMDn8fEwTZn+V0wlnyIohdO/D89pjjOSWGlALtRjF8pTUem/rALm6Ay
 0jKbpiHej8vvFOEA6oWYXpN/cGYs/62A2J8e6+rCrpgnPJpdoHtnuCj6LmioMAhM
 tdVXmwbAZB4VVee17WVRbmuZXapYpgcZ/GF73vgPwvz7lvGANBdLqCJT8r+j57eU
 jwAKpRTSMRBlYflQqodV/C9uBl/OaNI5tQ5L06kDtlR5SQti3CjqCI2paujCl+Op
 e/1HYAeooOQ+CmOjL3cRhiFiINJ/jKnXh+LmdvDUMGZX9WuWKD369YKFyKeB3Quy
 pKqdTX3vdjQmn7+JUWqAZhFQqmiDC1RJ4ZtJEN8oY+gjDriyBbm1PmvGJOL/S4Rt
 5hKFrgGMZCGChmyBNsoke2z2fMDNwCKZil2HIA8zZjAgGvVshf0jeo0VldMI29a+
 FocOJxy8wo2cZRG8vPILq4gVyOQtV4xgRoJloj3DTb+9Drz/1+lPLfRJd9h8+apS
 rcyk3cjJ9RNDWT7K0WLN50eQa/Jpc0o5rvVlVzExCX32D/KMLkwYCYh4LKiEOFlb
 nmcm80Q4JiGQbx7wfxT6bD0X1uXvSjCSuFCn9UDTK7/Arj+i94Q=
 =At4/
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-amlogic-20220427' of https://source.denx.de/u-boot/custodians/u-boot-amlogic

- Add AXG support for SARADC, including minimal ao-clk driver
- Update Amlogic documentation for Matrix & Jethub D1
2022-04-27 09:19:17 -04:00
Michal Simek
182d45ddff cpu: 83xx: Add missing dependency on CPU_MPC83XX
It looks quite weird that for non PPC platforms cpu driver for MPC83xx can
be selected. That's why define proper dependency.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2022-04-26 17:18:39 +05:30
Pali Rohár
95f8dfe8fb pci: fsl: Change compatible string for mpc8548 to "fsl, mpc8548-pcie"
Upstream Linux kernel uses for mpc8548-based PCIe controllers compatible
string "fsl,mpc8548-pcie". So change U-Boot fsl PCIe driver and all DTS
files to use "fsl,mpc8548-pcie" instead of "fsl,pcie-mpc8548" to be
compatible with Linux kernel.

Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2022-04-26 17:18:39 +05:30
Pali Rohár
0980cbba7b mmc: fsl_esdhc_spl: pre-PBL: implement redundancy support
QorIQ pre-PBL BootROM scans first 24 SD card sectors (each with fixed 512
bytes length) for boot signature. Implement same redundancy behavior in
fsl_esdhc_spl driver to allow loading proper U-Boot when boot sector is not
the first one.

Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2022-04-26 17:18:39 +05:30
Pali Rohár
44564e79eb mmc: fsl_esdhc: Define macro ESDHCCTL_SNOOP for Snoop attribute
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2022-04-26 17:18:39 +05:30
Pali Rohár
06ef911447 mtd: nand: raw: Add support for DT property nand-ecc-algo=bch
According to Linux kernel DT schema nand-controller.yaml, using DT property
nand-ecc-algo=bch is the correct way for specifying BCH as ECC algorithm.

Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2022-04-26 17:18:39 +05:30
Pali Rohár
c9ea9019c5 mtd: rawnand: fsl_elbc: Use ECC configuration from device tree
Initialize ECC configuration after nand_scan_ident() call and only in case
nand_scan_ident() have not done it. nand_scan_ident() fills ECC
configuration from device tree.

Fixes usage of NAND_ECC_SOFT_BCH when it is specified in device tree.

Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2022-04-26 17:18:39 +05:30
Pali Rohár
da98ddaf73 mtd: rawnand: fsl_elbc: Add device tree support
This allows boards to specify NAND settings via standard DT properties.

Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2022-04-26 17:18:39 +05:30
Pali Rohár
974f66a470 mtd: rawnand: fsl_elbc: Implement RNDOUT command
This is needed for SW ECC.

Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2022-04-26 17:18:39 +05:30
Pali Rohár
78cdaf4053 ddr: fsl: Allow to compile it without env support
When env support is disabled then usage of env_get_f() generates linker
errors. So do not compile env_get_f() when env support is disabled (for
example when disabled only in SPL).

Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2022-04-26 17:18:39 +05:30
Pali Rohár
48467e4769 mmc: mmc_mode_name() is used also when LOGLEVEL >= LOGL_DEBUG
When CONFIG_LOGLEVEL is set to LOGL_DEBUG or higher then linker throws
error about undefined symbol mmc_mode_name(). So compile mmc_mode_name()
also when CONFIG_LOGLEVEL is set to LOGL_DEBUG or higher.

Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2022-04-26 17:18:39 +05:30
Pali Rohár
57d527e753 mmc: fsl_esdhc_spl: Call mmc_init() before booting from SD card
If env is stored on SD card then U-Boot SPL automatically calls mmc_init()
before it is going to load proper U-Boot from SD card.

If env is not stored on SD card then U-Boot SPL fails to read proper U-Boot
from SD card due to missing mmc_init() call.

So add missing mmc_init() call into fsl_esdhc_spl's mmc_boot() function.
It fixes booting from SD card on P2020 boards without env support in SPL.

mmc_init() returns early if card was already initialized, so there is no
issue with calling this function more times.

Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2022-04-26 17:18:39 +05:30
Pali Rohár
a91998d8af mmc: fsl_esdhc_spl: pre-PBL: fix determining U-Boot size
In pre-PBL header is stored size of code which BootROM copies from SD card
to L2/SRAM. This size has upper limit of L2 cache size. In most cases this
is size of U-Boot SPL or size of L2 cache.

Therefore this size in pre-PBL header cannot be used for determining size
of proper U-Boot.

So always use CONFIG_SYS_MMC_U_BOOT_SIZE for determining size of proper
U-Boot which stored on SD card.

Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2022-04-26 17:18:39 +05:30
Pali Rohár
0f58f033d4 mmc: fsl_esdhc_spl: pre-PBL: check for BOOT signature instead of MBR/DBR
Pre-PBL BootROMs (MPC8536E, MPC8569E, P2020, P1011, P1012, P1013, P1020,
P1021, P1022) require custom BOOT signature on sector 0 and MBR/DBR
signature is not required at all.

So add check for BOOT signature and remove check for MBR/DBR.

This allows U-Boot SPL to load proper U-Boot on pre-PBL BootROMs platforms
also from SD cards which do not have MBR/DBR signature on sector 0.

Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2022-04-26 17:18:39 +05:30
Tudor Ambarus
20ced4b22a spi: atmel-quadspi: Fix the buswidth adjustment between spi-mem and controller
Use the spi_mem_default_supports_op() core helper in order to take into
account the buswidth specified by the user in device tree.

Fixes: 24c8ff4684 ("spi: Add Atmel QuadSPI driver")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
2022-04-26 09:54:41 +03:00
Eugen Hristev
632422d4b3 timers: atmel_pit: introduce CONFIG_SPL_ATMEL_PIT_TIMER
This commit allows the ATMEL_PIT_TIMER driver to be unselected in SPL and be
selected in u-boot proper. The SPL can use a different timer.
By having a separate Kconfig for ATMEL_TCB in SPL, the size of the SPL
decreases by 0.3 KBytes.

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2022-04-26 09:54:41 +03:00
Eugen Hristev
e135d2c2f3 timers: atmel_tcb: introduce CONFIG_SPL_ATMEL_TCB
This commit allows the ATMEL_TCB driver to be unselected in SPL and be
selected in u-boot proper. The SPL can use a different timer.
By having a separate Kconfig for ATMEL_TCB in SPL, the size of the SPL
decreases by 1 KByte.

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2022-04-26 09:53:49 +03:00
Sergiu Moga
71d4393f84 sysreset: Add Atmel/Microchip sysreset driver
This patch adds a sysreset driver for Atmel/Microchip platforms.

Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
2022-04-26 09:51:46 +03:00
Tom Rini
11232139e3 nds32: Remove the architecture
As removal of nds32 has been ack'd for the Linux kernel, remove support
here as well.

Cc: Rick Chen <rick@andestech.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Rick Chen <rick@andestech.com>
2022-04-25 16:04:05 -04:00
Tom Rini
8cfac237b9 Merge branch '2022-04-25-initial-implementation-of-stdboot'
To quote the author:
The bootflow feature provide a built-in way for U-Boot to automatically
boot an Operating System without custom scripting and other customisation.
This is called 'standard boot' since it provides a standard way for
U-Boot to boot a distro, without scripting.

It introduces the following concepts:

   - bootdev - a device which can hold a distro
   - bootmeth - a method to scan a bootdev to find bootflows (owned by
                U-Boot)
   - bootflow - a description of how to boot (owned by the distro)

This series provides an implementation of these, enabled to scan for
bootflows from MMC, USB and Ethernet. It supports the existing distro
boot as well as the EFI loader flow (bootefi/bootmgr). It works
similiarly to the existing script-based approach, but is native to
U-Boot.

With this we can boot on a Raspberry Pi 3 with just one command:

   bootflow scan -lb

which means to scan, listing (-l) each bootflow and trying to boot each
one (-b). The final patch shows this.

With a standard way to identify boot devices, booting become easier. It
also should be possible to support U-Boot scripts, for backwards
compatibility only.

...

The design is described in these two documents:

https://drive.google.com/file/d/1ggW0KJpUOR__vBkj3l61L2dav4ZkNC12/view?usp=sharing

https://drive.google.com/file/d/1kTrflO9vvGlKp-ZH_jlgb9TY3WYG6FF9/view?usp=sharing
2022-04-25 16:02:27 -04:00
Simon Glass
0ccb0ac5d8 bootstd: usb: Add a bootdev driver
Add a bootdev driver for USB host. It can use the distro boot mechanism to
locate a file, or any other available bootmeth.

Signed-off-by: Simon Glass <sjg@chromium.org>
2022-04-25 10:00:04 -04:00
Simon Glass
b8aa463e9b bootstd: mmc: Add a bootdev driver
Add a bootdev driver for MMC. It mostly just calls the bootdev helper
function.

Add a function to obtain the block device for an MMC controller.

Fix up the comment for mmc_get_blk_desc() while we are here.

Signed-off-by: Simon Glass <sjg@chromium.org>
2022-04-25 10:00:04 -04:00
Simon Glass
87571b7f20 dm: blk: Add a function to return the device type
Use the uclass name to get the device type for a block device.

Signed-off-by: Simon Glass <sjg@chromium.org>
2022-04-25 10:00:03 -04:00
Simon Glass
4e0710a2d0 dm: core: Allow finding a uclass device by partial name
In some cases two devices are related and the only way to tell is to
check that the names partially patch. Add a way to check this without
needing to create a new string for the comparison.

Fix the comment for device_find_child_by_namelen() while we are here.

Signed-off-by: Simon Glass <sjg@chromium.org>
2022-04-25 10:00:03 -04:00
Simon Glass
6aa4fe3912 dm: core: Rename and fix uclass_get_by_name_len()
It seems that namelen is more common in U-Boot. Rename this function to
fit in better. Also fix a bug where it breaks the operation of
uclass_get_by_name() and add a test.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reported-by: Tim Harvey <tharvey@gateworks.com>
2022-04-25 10:00:03 -04:00
Vyacheslav Bocharov
8a4a73f466 adc: meson-saradc: add AXG variant
Add support for the SARADC variant found on the AXG SoCs family.

Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20220424082159.757622-5-adeep@lexina.in
2022-04-25 09:25:00 +02:00
Vyacheslav Bocharov
66a657b7c6 clk: meson: update driver for g12a-ao clocks
Update g12a-ao clk driver:
- move clk->id check to .request function
- remove unnecessary check (gate->reg == 0)

Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20220424082159.757622-4-adeep@lexina.in
2022-04-25 09:25:00 +02:00
Vyacheslav Bocharov
4da0986562 clk: meson: fix driver name for g12a-ao clocks
Update the clk-g12a-ao driver from "axg" to "g12a"

Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20220424082159.757622-3-adeep@lexina.in
2022-04-25 09:25:00 +02:00
Vyacheslav Bocharov
dcccf73004 clk: meson: add minimal driver for axg-ao clocks
Add minimal driver AO clocks on meson AXG family. Only ADC related clocks
are supported.

Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20220424082159.757622-2-adeep@lexina.in
2022-04-25 09:24:59 +02:00
AKASHI Takahiro
bf76031d19 dm: blk: add a device-probe hook for scanning disk partitions
Now that all the block device drivers have enable a probe hook, we will
call part_create_block_devices() to enumerate all the partitions and
create associated udevices when a block device is detected.

Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
2022-04-23 22:05:41 +02:00
AKASHI Takahiro
a806f33401 dm: tag: change ENOSPC to ENOMEM
ENOMEM is a more common error code for memory starvation.

Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
2022-04-23 22:05:34 +02:00
Tom Rini
faeb564113 Merge https://gitlab.denx.de/u-boot/custodians/u-boot-pmic 2022-04-22 11:06:38 -04:00
Tom Rini
6d73175b1f Merge https://gitlab.denx.de/u-boot/custodians/u-boot-usb 2022-04-22 11:06:31 -04:00
Sean Anderson
847990219c power-domain: Fix use of uninitialized value in dev_power_domain_ctrl
If dev_count_phandle_with_args returns 0 or another error, then pd will never
have been initialized by power_domain_get_by_index. Avoid comparing against
pd.dev in this situation.

Fixes: 3e4fcfa4bc ("power-domain: fix hang in endless loop on i.MX8")
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2022-04-22 21:19:21 +09:00
Tom Rini
759a89924b Merge https://gitlab.denx.de/u-boot/custodians/u-boot-watchdog
- device-tree-bindings: watchdog: document common properties (Philippe)
- nuvoton: Add support for Nuvoton (Jim)
2022-04-22 08:12:53 -04:00
Tom Rini
6e2af641e4 u-boot-imx-20220422
-------------------
 
 - Switch to DM_SERIAL
 - Drop MMCROOT
 - several cleanup
 
 CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/11815
 -----BEGIN PGP SIGNATURE-----
 
 iG0EABECAC0WIQS2TmnA27QKhpKSZe309WXkmmjvpgUCYmJq1Q8cc2JhYmljQGRl
 bnguZGUACgkQ9PVl5Jpo76ZlxQCfQNPkQVf10kjENID/D9mu+Hl2tMEAnj8AMOyF
 iQrcw6oegrVvZZXV+s2J
 =XjAE
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-imx-20220422' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx

u-boot-imx-20220422
-------------------

- Switch to DM_SERIAL
- Drop MMCROOT
- several cleanup

CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/11815
2022-04-22 08:12:20 -04:00
Oleksii Titov
6674d2d9fe Add support for TP-Link UE200 dongle
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Oleksii Titov <ootitov@gmail.com>
2022-04-22 10:35:14 +02:00
Michal Simek
142d50fbce usb: dwc3: Add support for usb3-phy PHY configuration
When usb3-phy label is found, PHY driver is called and serdes line is
initialized. This is preparation for serdes/psgtr driver to configure GT
lines based on description in DT.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2022-04-22 10:35:14 +02:00
Adam Ford
570eaadac0 usb: gadget: ci: Make various ops const
ci_udc_ops and ci_ep_ops do not change their operations.
Mark them as const.

Signed-off-by: Adam Ford <aford173@gmail.com>
2022-04-22 10:35:14 +02:00
Jim Liu
e885d09dd0 wdt: nuvoton: Add support for Nuvoton
Add watchdog controller driver for NPCM7xx/npcm8xx

the wdt design of npcm750 and npcm845 is the same.
so the driver can work on npcm750 and npcm845.
about npcm845 wdt dtsi i will followed kernel dts name
to use nuvoton,npcm750-wdt.

Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
2022-04-22 09:02:55 +02:00
Pali Rohár
467f0c4dc2 misc: atsha204a: Remove duplicate CRC-16 implementation
ATSHA204A uses bit-reversed checksum of standard CRC-16 with polynomial
x^16 + x^15 + x^2 + 1.

This ATSHA204A specific checksum can be calculated just by using common
U-Boot functions bitrev16() and crc16().

So replace custom driver CRC-16 implementation by common U-Boot functions.

Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
2022-04-21 14:32:40 -04:00
Gaurav Jain
2c16bf2d14 crypto/fsl: add invalidate_dcache_range for hash output buffer
HW accelerated hash operations are giving incorrect hash output.
so invalidate cache lines to avoid cache overwriting in DDR memory region.

caam_hash()
 -moved address alignment check in the beginning of function.
 -added invalidate_dcache_range for pout buffer before running descriptor.

Fixes: d7af2baa49 (crypto/fsl: Fix HW accelerated hash commands)
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
2022-04-21 15:18:25 +02:00
Gaurav Jain
cc84edddd1 crypto/fsl: Clear the memory when blob decapsulation fails
issue: blob decapsulation operation store the decrypted data
       in memory even if ICV check failed.

fix: clear the blob data output memory.

Fixes: c5de15cbc8 (crypto/fsl: Add command for encapsulating/decapsulating blobs)
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Reviewed-by: Kshitiz Varshney <kshitiz.varshney@nxp.com>
Tested-by: Kshitiz Varshney <kshitiz.varshney@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
2022-04-21 15:18:25 +02:00
Tim Harvey
e3bdc97148 pci: imx: remove weak overrides no longer used
There are no users of the imx6_pcie_toggle_power and imx6_pcie_toggle_reset
weak overrides and as these functions are able to be handled now via dt
properties lets remove these.

Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2022-04-21 14:38:03 +02:00
Tim Harvey
6f6e069ca3 pci: imx: use vpcie-supply if defined by device-tree
If vpcie-supply is defined by device-tree use that if
CONFIG_PCIE_IMX_POWER_GPIO is not defined.

Note that after this the following boards which define
CONFIG_PCIE_IMX_POWER_GPIO in their board header file as well as their
device-tree should be able to remove CONFIG_PCIE_IMX_PERST_GPIO without
consequence:
 - mx6sabresd
 - mx6sxsabresd
 - novena

Note that the ge_bx50v3 board uses CONFIG_PCIE_IMX_POWER_GPIO and does
not have vpcie-supply defined in it's pcie node in the dt thus removing
CONFIG_PCIE_IMX_POWER_GPIO globally can't be done until that board adds
vpcie-supply.

Cc: Ian Ray <ian.ray@ge.com> (maintainer:GE BX50V3 BOARD)
Cc: Sebastian Reichel <sebastian.reichel@collabora.com> (maintainer:GE BX50V3 BOARD)
Cc: Fabio Estevam <festevam@gmail.com> (maintainer:MX6SABRESD BOARD)
Cc: Marek Vasut <marex@denx.de> (maintainer:NOVENA BOARD)
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2022-04-21 14:38:03 +02:00
Marek Vasut
d0f7a0559a usb: dwc3: Implement .glue_configure for i.MX8MP
The i.MX8MP glue needs to be configured based on a couple of DT
properties, implement .glue_configure callback to parse those DT
properties and configure the glue accordingly.

Tested-By: Tim Harvey <tharvey@gateworks.com> #imx8mp-venice-gw74xx
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Angus Ainslie <angus@akkea.ca>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2022-04-21 12:44:23 +02:00
Marek Vasut
f1ef95591c usb: dwc3: Rename .select_dr_mode to .glue_configure
Rename the select_dr_mode callback to glue_configure, the callback is
used for more than enforcing controller mode even on the TI chips, so
change the name to a more generic one. No functional change.

Tested-By: Tim Harvey <tharvey@gateworks.com> #imx8mp-venice-gw74xx
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Angus Ainslie <angus@akkea.ca>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2022-04-21 12:44:23 +02:00
Marek Vasut
898e7610c6 imx: power-domain: Add i.MX8MP HSIOMIX driver
Add trivial driver for i.MX8MP HSIOMIX handling. This is responsible
for enabling the GPCv2 power domains and clock for USB 3.0 and PCIe
in the correct order. Currently supported is the USB 3.0 part which
can be tested, PCIe support should be easy to add.

Tested-By: Tim Harvey <tharvey@gateworks.com> #imx8mp-venice-gw74xx
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2022-04-21 12:44:23 +02:00
Marek Vasut
2e760f180d imx: power-domain: Add i.MX8MP support
Add i.MX8MP power domain handling into the driver. This is based on the
Linux GPCv2 driver state which is soon to be in Linux next.

Tested-By: Tim Harvey <tharvey@gateworks.com> #imx8mp-venice-gw74xx
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2022-04-21 12:44:23 +02:00
Marek Vasut
63c390a1ea power_domain: Add power_domain_get_by_name()
Implement power_domain_get_by_name() convenience function which parses
DT property 'power-domain-names' and looks up power domain by matching
name.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Simon Glass <sjg@chromium.org>
2022-04-21 12:44:23 +02:00
Marek Vasut
4eb82c2e56 imx: power-domain: Get rid of SMCCC dependency
This driver is the only SMCCC dependency in iMX8M U-Boot port. Rework
the driver based on Linux GPCv2 driver to directly control the GPCv2
block instead of using SMCCC calls. This way, U-Boot can operate the
i.MX8M power domains without depending on anything else.

This is losely based on Linux GPCv2 driver. The GPU, VPU, MIPI power
domains are not supported to save space, since they are not useful in
the bootloader. The only domains kept are ones for HSIO, PCIe, USB.

Tested-By: Tim Harvey <tharvey@gateworks.com> #imx8mp-venice-defconfig
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2022-04-21 12:44:23 +02:00
Marek Vasut
19842b6a20 imx: power-domain: Inline arch-imx8m/power-domain.h
The arch/arm/include/asm/arch-imx8m/power-domain.h is not included
anywhere except in drivers/power/domain/imx8m-power-domain.c, just
inline the content and drop the header. No functional change.

Tested-By: Tim Harvey <tharvey@gateworks.com> #imx8mp-venice-defconfig
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2022-04-21 12:44:23 +02:00
Marek Vasut
8741d92756 imx: power-domain: Descend into pgc subnode if present
In case the power domain node structure is gpc@303a0000/pgc/power-domain@N,
do not bind power domain driver to the 'pgc' node, but rather descend into
it and only bind power domain drivers to power-domain@N subnodes. This way
we do not waste one useless driver instance associated with 'pgc' node.

Tested-By: Tim Harvey <tharvey@gateworks.com> #imx8mp-venice-defconfig
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2022-04-21 12:44:23 +02:00
Marek Vasut
20874a6072 power-domain: Return 0 if ops unimplemented and remove empty functions
In case the ops is not implemented, return 0 in the core right away.
This is better than having multiple copies of functions which just
return 0 in each power domain driver. Drop all those empty functions.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Simon Glass <sjg@chromium.org>
2022-04-21 12:44:23 +02:00
Robert Marko
2b7beb9c09 net: mvneta: add SFP TX disable handling
Add support for handling SFP TX disable for MVNETA in the same fashion as
to what MVPP2 is doing in order to enable using SFP-s.

This allows using ethernet on SFP only boards.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2022-04-21 12:31:36 +02:00
Dave Gerlach
270f7fd25b ram: k3-ddrss: Allow use of dt provided initial frequency
Allow device tree to provide ti,ddr-freq0 to be used as the initial DDR
frequency that is set for lpddr4 before initialization of the
controller. Make this optional and continue to use PLL bypass frequency
as is done currently if ti,ddr-freq0 is not provided.

Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
2022-04-20 11:14:39 -04:00
Dominic Rath
b4c80f245b ram: k3-ddrss: Fix register name and explain its usage
The k3-ddrss driver wants to configure the DDRSS_V2A_CTL_REG to reflect
the maximum possible SDRAM of 2 GB for AM64x (instead of the register's
default that says 8 GB, which the AM64x DDR controller wouldn't support).

The offset 0x20 was correct, but the register name DDRSS_V2A_R1_MAT_REG
was that of the next register at offset 0x24.

Signed-off-by: Dominic Rath <rath@ibv-augsburg.net>
2022-04-20 11:14:39 -04:00
Billy Tsai
fe2f284270 gpio: aspeed: Fix incorrect offset of read back register.
The offset of the current read back register is the value of the gpio pin,
not the value written for the gpio output.
This patch fix it to avoid the other gpio output value controlled by the
same register being set incorrectly.

Fixes: 7ad889b0f3 ("gpio: Add Aspeed GPIO driver")
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
2022-04-19 14:51:11 -04:00
Tom Rini
9acf3726b6 Merge tag 'u-boot-rockchip-20220418' of https://source.denx.de/u-boot/custodians/u-boot-rockchip
- Add rk3066 SoC support;
- Add rk3066 MK808 board support;
- dts sync from kernel for rk322x, rk3288;
- some other board level config update;
2022-04-19 08:50:40 -04:00
Simon Glass
cdd73e7215 dm: core: Deal with a wrinkle with linker lists
When every member of a linker list is aligned by the compiler, we can no
longer rely on the sizeof of the struct to determine the number of
entries.

For example, if the struct size is 0x90 but every entry is aligned to 0xa0
by the compiler, the linker list entries takes more space in memory and
the calculation of the number of entries is incorrect. For example, we may
see 0x12 entries when there are only 0x11.

This is a real problem. There may be a general solution, although I cannot
currently think of one. So far it only bites with OF_PLATDATA_RT which
creates a pointer to each entry of the 'struct udevice' linker_list. This
does not happen without that option, so it only affects SPL.

Work around it by manually calculating the aligned size of struct udevice,
then using that for the n_ent calculation.

Note: the alignment fix to linker list was here:

   0b2fa98aa5 linker_lists: Fix alignment issue

Signed-off-by: Simon Glass <sjg@chromium.org>
2022-04-18 17:53:56 -04:00
Simon Glass
092d5c2a83 dm: core: Allow devres to be disabled in SPL
At present if devres is enabled in U-Boot proper it is enabled in SPL.
We don't normally want it there, so disable it.

Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Angus Ainslie <angus@akkea.ca>
2022-04-18 17:53:56 -04:00
Johan Jonker
dcaaefdc0a rockchip: video: mipi: add more compatible strings for rk3288/rk3399
The rk3288/RK3399 DT synced from Linux contains some different
compatible strings in the mipi node then origanal used in U-boot.
Allow both options to be backwards compatible and to be able
to handle recent rk3288.dtsi and rk3399.dtsi files.

Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2022-04-18 11:25:13 +08:00
Johan Jonker
0944e77fde rockchip: video: rk_edp: add more rk3288 edp node options
The rk3288 DT synced from Linux contains some different
properties in the edp node then origanal used in U-boot.
Allow both options to be backwards compatible and to be able
to handle recent rk3288.dtsi files.

Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2022-04-18 11:25:13 +08:00
Paweł Jarosz
4b957e7ff5 rockchip: rk3066: add sdram driver
Add rockchip rk3066 sdram driver

Signed-off-by: Paweł Jarosz <paweljarosz3691@gmail.com>
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2022-04-18 11:25:13 +08:00
Paweł Jarosz
086863c982 rockchip: rk3066: add rk3066 pinctrl driver
Add driver supporting pin multiplexing on rk3066 platform.

Signed-off-by: Paweł Jarosz <paweljarosz3691@gmail.com>
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2022-04-18 11:25:13 +08:00
Paweł Jarosz
730a402450 rockchip: rk3066: add clock driver for rk3066 soc
Add the clock driver for the rk3066 platform.

Derived from the rk3288 and rk3188 driver it
supports only a bare minimum to bring up the system
to reduce the TPL size for:
  SDRAM clock configuration.
  The boot devices NAND, EMMC, SDMMC, SPI.
  A UART for the debug messages (fixed) at 115200n8.
  A SARADC for the recovery button.
  A TIMER for the delays (fixed).

There's support for two possible frequencies,
the safe 600MHz which will work with default pmic settings and
will be set to get away from the 24MHz default and
the maximum of 1.416Ghz, which boards can set if they
were able to get pmic support for it.

After the clock tree is set during the TPL probe
there's no parent update support.

In OF_REAL mode the drivers ns16550.c and dw-apb-timer.c
obtain the (fixed) clk_get_rate from the clock driver
instead of platdata.

The rk3066 cru node has a number of assigned-clocks properties
that call the .set_rate() function. Add them to the list so that
they return a 0 instead of -ENOENT.

Signed-off-by: Paweł Jarosz <paweljarosz3691@gmail.com>
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2022-04-18 11:25:13 +08:00
Johan Jonker
9ee6c0766d rockchip: serial: Kconfig: allow ROCKCHIP_SERIAL enabled in TPL
The serial_rockchip.c driver converts platdata to the data structure
used in the ns16550.c file and then calls the function
ns16550_serial_probe().
When compiled with OF_REAL the serial_rockchip.c driver returns
now -ENODEV when probed and does no harm.
The config ROCKCHIP_SERIAL is currently depends on SPL_OF_PLATDATA.
Allow serial port use for both SPL and TPL by removing this
dependency and SPL_BUILD restriction.

Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2022-04-18 11:25:13 +08:00
Johan Jonker
6dcaf2d22b rockchip: serial: Kconfig: add select SYS_NS16550 to config ROCKCHIP_SERIAL
The Rockchip serial driver depends on an enabled NS16550 driver,
so add select SYS_NS16550 to config ROCKCHIP_SERIAL.

Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2022-04-18 11:25:13 +08:00
Johan Jonker
6e2ee2ebb8 rockchip: serial: rename U_BOOT_DRIVER name to rockchip_uart
When a defconfig for rk3288 is compiled it gives the warning:

rockchip_rk3288_uart: Missing .compatible in
                      ./drivers/serial/serial_rockchip.c
                    : WARNING: the driver rockchip_rk3288_uart
                      was not found in the driver list

Fix by renaming U_BOOT_DRIVER name of serial_rockchip.c
to rockchip_uart. Add rk3288 serial support with
a DM_DRIVER_ALIAS define.

Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2022-04-18 11:25:13 +08:00
Johan Jonker
04ee76c988 rockchip: serial: move driver alias to serial_rockchip.c
The Rockchip uart DT nodes have "snps,dw-apb-uart" as
fall back string. The driver ns16550.c has CONFIG_IS_ENABLED(OF_REAL)
as condition to of_match and does not copy dtplat data.
For TPL/SPL the driver serial_rockchip.c
is used. Move driver alias to correct driver.

Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2022-04-18 11:25:13 +08:00
Johan Jonker
728489753c rockchip: serial: restyle the serial_rockchip.c driver
The ns16550.c driver has the following conditions for .of_match:

CONFIG_IS_ENABLED(OF_REAL)

For Rockchip SoCs with TPL/SPL and platform data that need serial
support the serial_rockchip.c driver was made. It copies this data
and then calls ns16550_serial_probe(). With the addition of yet an other
SoC type this driver is in need for a little restyle.
Simplify struct rockchip_uart_plat and add extra SoCs with
DM_DRIVER_ALIAS(). Return -ENODEV when the ns16550.c driver
probe function is available.

Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2022-04-18 11:25:13 +08:00
Johan Jonker
2d3bb400f3 rockchip: mmc: rockchip_dw_mmc: add rk3066/rk3188 support
The Rockchip SoCs rk3066/rk3188 have MMC DT nodes
with as compatible string "rockchip,rk2928-dw-mshc".
Add OF_PLATDATA support to the existing driver with
help of a DM_DRIVER_ALIAS.

This type needs a permanent enabled fifo.
The other Rockchip SoCs always have the property
"u-boot,spl-fifo-mode" in the MMC DT nodes,
because MMC to SRAM can't do DMA.
Make this property a requirement for MMC OF_PLATDATA
structures. The property "fifo-mode" must be added
for all other compile modes.

Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2022-04-18 11:25:13 +08:00
Johan Jonker
9d75dafb1b rockchip: mmc: rockchip_dw_mmc: fix ciu clock index
The document rockchip-dw-mshc.yaml decribes a maximum of 4 clocks.
In the rockchip_dw_mmc driver the clock name in use was "fixed"
to "ciu" with index 1, but later reverted back to index 0.
The clock drivers can handle both, but the calling driver
should submit correct data as a standard practice.
Fix the "ciu" clock index by setting it back to 1.

  clock-names:
    minItems: 2
    items:
      - const: biu
      - const: ciu
      - const: ciu-drive
      - const: ciu-sample

Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2022-04-18 11:25:13 +08:00
Johan Jonker
3930209526 rockchip: timer: dw-apb-timer: fix whitespace in U_BOOT_DRIVER structure
The line with .of_to_plat in the U_BOOT_DRIVER structure
of dw-apb-timer.c is not aligned with the rest.
Add an extra TAB to fix the whitespace.

Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2022-04-18 11:25:13 +08:00
Johan Jonker
516e216a78 rockchip: timer: add OF_PLATDATA support for dw-apb-timer
The Rockchip rk3066 SoC has 3 dw-apb-timer nodes.
U-boot is compiled with OF_PLATDATA TPL/SPL options,
so add OF_PLATDATA support for the dw-apb-timer.
Also change driver name to be able to compile with
U-boot scripts. No reset OF_PLATDATA support was added,
because the rk3066 nodes don't need/have them.

Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2022-04-18 11:25:13 +08:00
Chris Morgan
0abb5b0426 rockchip: clk: add clocks to px30_clk_enable
Add the HCLK_OTG, HCLK_SFC, and SCLK_SFC clocks to px30_clk_enable.
Without this change U-Boot reports an error of "Enable
clock-controller@ff2b0000 failed" on boot when using the SFC or USB in
U-Boot.

Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2022-04-18 11:25:12 +08:00
Chris Morgan
f0d49d4f0d spi: rockchip_sfc: Add missing include for dm/device_compat.h
Add missing include for dm/device_compat.h. Without this include the
SFC driver fails to compile because dev_err and dev_dbg are not
defined.

Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2022-04-18 11:25:12 +08:00
Peter Cai
e963228af5 adc: rockchip-saradc: add support for getting reference voltage value
Mirroring commit 97ab802aa3 ("adc: meson-saradc: add support for
getting reference voltage value") for meson-saradc, this adds support
for getting the "vref-supply" regulator and register it as the ADC's
reference voltage regulator, so clients can translate sampled ADC values
to voltage.

Signed-off-by: Peter Cai <peter@typeblog.net>
Reviewed-by: John Keeping <john@metanate.com>
Tested-by: John Keeping <john@metanate.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Philipp Tomsich <philipp.tomsich@vrull.eu>
Cc: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2022-04-18 11:25:12 +08:00
Haolin Li
fdda7901cc mmc: rockchip_sdhci: Correct error checking
A pointer can not be negative. Use macro IS_ERR_OR_NULL() for checking.

Signed-off-by: Haolin Li <li.haolin@qq.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2022-04-18 11:25:12 +08:00
Tom Rini
7f418ea598 Merge branch 'next' of https://source.denx.de/u-boot/custodians/u-boot-net
- DM9000 DM support
- tftp server bug fix
- mdio ofnode support functions
- Various phy fixes and improvements.

[trini: Fixup merge conflicts in drivers/net/phy/ethernet_id.c
drivers/net/phy/phy.c include/phy.h]
2022-04-15 08:10:32 -04:00
Tom Rini
2df59b2bd4 Remove duplication of table_compute_checksum function
It seems like there was some merge error when first cleaning up and
sharing this function.  We have both an inline version of the function
in include/tables_csum.h and a non-inline version in lib/tables_csum.c.
Rework things so that we only have the non-inline version (due to number
of calls, we should not inline this).

Fixes: 1befb38b86 ("x86: Move table csum into separate file")
Fixes: 2b445e4d31 ("x86: Move table csum into separate header")
Cc: Alexander Graf <agraf@csgraf.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
2022-04-14 15:39:15 -04:00
Sean Anderson
34855b39be serial: smh: Implement puts for DM
This adds an implementation of puts for DM. The implementation is not as
clean as for the non-DM puts because we have to handle non-nul-terminated
string. We also handle short writes (though these are probably very
unusual).

Signed-off-by: Sean Anderson <sean.anderson@seco.com>
2022-04-14 15:39:15 -04:00
Sean Anderson
679190c41a test: serial: Add test for putc/puts
This adds a test to ensure that puts is equivalent to putc called in a
loop. We don't verify the contents of the message to avoid having to
record console output a second time (though that could be added in the
future). The globals are initialized to non-zero values to avoid a
warning; in particular, the character count is off-by-one (but we always
make relative measurements).

Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2022-04-14 15:39:15 -04:00
Sean Anderson
efa51f2bd6 serial: sandbox: Implement puts
This implements puts for sandbox. It is fairly straightforward, except
that we break out the shared color printing functionality into its own
function.

Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2022-04-14 15:39:15 -04:00
Sean Anderson
2c777488b6 serial: Fix _serial_puts using \n\r instead of \r\n
A string like "test\n" would be broken up into the following sequence of
prints by _serial_puts:

	puts("test\n")
	putc('\r')

Although functionally this is the same as \r\n, it is not the standard
sequence and caused tests to fail. Fix this by excluding the '\n' from
the initial print. The above string will now be broken up like

	puts("test")
	puts("\r\n")

Since we may now need to call ops->puts twice (with the associated retry
logic), break that part of the function off into a helper.

Fixes: 7a76347189 ("serial: dm: Add support for puts")
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
2022-04-14 15:39:15 -04:00
Marek Vasut
72675b063b led: Configure LED default-state on boot
In case the DT LED subnode contains "default-state" property set to
either "on" or "off", probe the LED driver and configure the LED state
automatically.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Philippe Reynes <philippe.reynes@softathome.com>
Cc: Sean Anderson <seanga2@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Steven Lawrance <steven.lawrance@softathome.com>
[trini: Update the relevant test now that we have support]
Signed-off-by: Tom Rini <trini@konsulko.com>
2022-04-14 15:39:15 -04:00
Marek Vasut
2d1deaf88e led: gpio: Drop duplicate OF "label" property parsing
The OF "label" property parsing is now handled in LED core,
drop the duplicate implementation from this driver.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Philippe Reynes <philippe.reynes@softathome.com>
Cc: Sean Anderson <seanga2@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Steven Lawrance <steven.lawrance@softathome.com>
2022-04-14 15:39:15 -04:00
Tom Rini
d797dd4c1e led: pwm: Drop duplicate OF "label" property parsing
The OF "label" property parsing is now handled in LED core,
drop the duplicate implementation from this driver.

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-04-14 15:39:15 -04:00
Tom Rini
4228023eff led: bcm6753: Drop duplicate OF "label" property parsing
The OF "label" property parsing is now handled in LED core,
drop the duplicate implementation from this driver.

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-04-14 15:39:15 -04:00
Marek Vasut
c6db8eb4f6 led: cortina: Drop duplicate OF "label" property parsing
The OF "label" property parsing is now handled in LED core,
drop the duplicate implementation from this driver.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Philippe Reynes <philippe.reynes@softathome.com>
Cc: Sean Anderson <seanga2@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Steven Lawrance <steven.lawrance@softathome.com>
2022-04-14 15:39:15 -04:00
Marek Vasut
fec9156478 led: bcm6858: Drop duplicate OF "label" property parsing
The OF "label" property parsing is now handled in LED core,
drop the duplicate implementation from this driver.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Philippe Reynes <philippe.reynes@softathome.com>
Cc: Sean Anderson <seanga2@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Steven Lawrance <steven.lawrance@softathome.com>
2022-04-14 15:39:15 -04:00
Marek Vasut
93c3722085 led: bcm6358: Drop duplicate OF "label" property parsing
The OF "label" property parsing is now handled in LED core,
drop the duplicate implementation from this driver.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Philippe Reynes <philippe.reynes@softathome.com>
Cc: Sean Anderson <seanga2@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Steven Lawrance <steven.lawrance@softathome.com>
2022-04-14 15:39:15 -04:00
Marek Vasut
9183fb45b8 led: bcm6328: Drop duplicate OF "label" property parsing
The OF "label" property parsing is now handled in LED core,
drop the duplicate implementation from this driver.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Philippe Reynes <philippe.reynes@softathome.com>
Cc: Sean Anderson <seanga2@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Steven Lawrance <steven.lawrance@softathome.com>
2022-04-14 15:39:14 -04:00
Marek Vasut
83c63f0d11 led: Move OF "label" property parsing to core
Every driver in drivers/led/ currently does some form of "label" OF
property parsing in its bind() callback. Move this label parsing to
LED core, since this "label" OF property is a generic property. This
permits code deduplication in subseuqent patches.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Philippe Reynes <philippe.reynes@softathome.com>
Cc: Sean Anderson <seanga2@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Steven Lawrance <steven.lawrance@softathome.com>
2022-04-14 15:39:14 -04:00
Pali Rohár
aecb338163 misc: atsha204a: Fix big endian support
Callers of function atsha204a_crc16() expect to return value in host cpu
endianity. So remove cpu_to_le16() conversion.

Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
2022-04-14 15:39:14 -04:00
Dave Gerlach
e9598cfb28 power: domain: ti: Extend use of PTCMD and PTSTAT registers for high PDs
It is possible for power domain IDs to be great than 31. If this
happens, the PTCMD and PTSTAT registers must overflow into adjacent
corresponding PTCMD_H and PTSTAT_H registers for each. Update the driver
to account for this.

Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
2022-04-14 15:39:14 -04:00
Marek Vasut
f478da938f net: dm9000: Add Kconfig entry
Add Kconfig entry for the DM9000 MAC.

Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
2022-04-13 15:13:54 +03:00
Marek Vasut
41e10bea31 net: dm9000: Add DM support
Add support for U-Boot DM and DT probing.

Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
2022-04-13 15:13:54 +03:00
Marek Vasut
84bf20f6ce net: dm9000: Receive one packet per recv call
Instead of reading out the entire FIFO and possibly overwriting U-Boot
memory, read out one packet per recv call, pass it to U-Boot network
stack, and repeat.

Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
2022-04-13 15:13:54 +03:00
Marek Vasut
85a7260186 net: dm9000: Split non-DM specific bits from common code
Split network handling functions into non-DM specific parts and
common code in preparation for conversion to DM.

Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
2022-04-13 15:13:54 +03:00
Marek Vasut
f0d1a29dc5 net: dm9000: Pass private data around for IO
Pass private data into IO accessors and use the base addresses of
IO and DATA window from the private data instead of using the hard
coded macros DM9000_IO/DM9000_DATA. Currently both the DM9000_IO
and DM9000_DATA are assigned to the respecive private data fields
for the non-DM case backward compatibility.

Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
2022-04-13 15:13:54 +03:00
Marek Vasut
1494a4aace net: dm9000: Drop dm9000.h and staticize SROM access
Dispose of dm9000.h because none of the function prototypes declared in
it are called anywhere in the codebase. Staticize dm9000_read_srom_word()
because it is now called only from within the dm9000 driver. Drop
dm9000_write_srom_word() because it is no longer used.

Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
2022-04-13 15:13:54 +03:00
Marek Vasut
3928055e4f net: dm9000: Drop static device private data
Allocate driver private data dynamically in its init function and drop
the static driver private data variable. Pass the dynamic private data
throughout the driver. This is done in preparation for DM conversion.

Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
2022-04-13 15:13:54 +03:00
Marek Vasut
8371edd52f net: dm9000: Rename board_info to dm9000_priv
Rename board_info structure to dm9000_priv to make it clear what this
structure really contains, the driver private data. No functional change.

Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
2022-04-13 15:13:54 +03:00
Marek Vasut
a2e92304bb net: dm9000: Reorder and staticize
Reorder the driver functions to get rid of forward declarations.
Staticize whatever is possible. No functional change.

Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
2022-04-13 15:13:54 +03:00
Marek Vasut
a7bebf8d4d net: dm9000: Checkpatch cleanup
Fix checkpatch errors and warnings. No functional change.

Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
2022-04-13 15:13:54 +03:00
Marek Vasut
6d3de0f6db net: dm9000: Drop volatiles
Remove volatile keyword usage from arrays, they are not really volatile
in any way, so this keyword is misused here. No functional change.

Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
2022-04-13 15:13:54 +03:00
Marek Vasut
c7b7ee52b2 net: dm9000: Turn DM9000_DMP_PACKET() into a function
Rework DM9000_DMP_PACKET() into dm9000_dump_packet() function,
this brings better type checking. No functional change.

Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
2022-04-13 15:13:54 +03:00
Marek Vasut
d1854794c0 net: dm9000: Drop unused dump_regs()
Drop unused function dump_regs() because it is unused.
No functional change.

Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
2022-04-13 15:13:54 +03:00
Marek Vasut
d8f21b2358 net: dm9000: Make RxLen and RxStatus lowercase
Rename variables to lowercase to be consistent with coding style.
No functional change.

Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
2022-04-13 15:13:54 +03:00
Marek Vasut
42a7e0f2d7 net: dm9000: Replace DM9000_DBG() with debug()
Use standard debug() macro to print debug messages instead of
reinventing driver-specific macro again. No functional change.

Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
2022-04-13 15:13:54 +03:00
Marek Vasut
ff61d4eb74 net: dm9000: Make accessor names lowercase
Make accessor names lowercase to be consistent with coding style.
No functional change.

Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
2022-04-13 15:13:54 +03:00
Marek Behún
af8b0a8d2c driver: net: ti: keystone_net: Change priv member type
Change type of private struct member mdio_base from void * to
phys_addr_t. This allows us to drop 2 casts.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
2022-04-13 15:12:03 +03:00
Marek Behún
71b65d8210 driver: net: ti: keystone_net: Convert to ofnode functions
Convert fdt parsing functions to ofnode parsing functions.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
2022-04-13 15:12:03 +03:00
Marek Behún
71f473916d driver: net: ti: keystone_net: Deduplicate code
Deduplicate common code in ks2_eth_bind_slaves().

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
2022-04-13 15:12:03 +03:00
Tom Rini
2ddf84679d u-boot-imx-20220413
i.MX patches for 2022.07
 
 CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/11710
 -----BEGIN PGP SIGNATURE-----
 
 iG0EABECAC0WIQS2TmnA27QKhpKSZe309WXkmmjvpgUCYlaYFg8cc2JhYmljQGRl
 bnguZGUACgkQ9PVl5Jpo76Y1RQCgjI6iHC1yb0245e2RoV3VIeib9mEAoIUKX3yE
 HbvZYN8YZbQHlNOiSOZo
 =z3fU
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-imx-20220413' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx

u-boot-imx-20220413

i.MX patches for 2022.07

CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/11710
2022-04-13 08:00:11 -04:00
Marek Vasut
2c6ae0a15f clk: imx8mp: Fix 24M and 32k clock
Fix registration of 24M and 32k clock, those got applied or rebased
incorrectly, so fill in the correct code.

Fixes: 7a2c3be95a ("clk: imx8mp: Fill in DWC3 USB, USB PHY, HSIOMIX clock")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
2022-04-13 09:38:25 +02:00
Elmar Albert
87f958810f clk: imx8mp: Add ECSPI clocks
Add clock tables required for bing up ECSPI interfaces

Signed-off-by: Elmar Albert <ealbert@data-modul.com>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: uboot-imx <uboot-imx@nxp.com>
Signed-off-by: Elmar Albert <ealbert@data-modul.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
2022-04-12 23:27:32 +02:00
Jesse Taube
a2d6fbf5ff clk: imxrt: Use dts for anatop base address
In Linux IMX and IMXRT use the device tree to hold the anatop address.
The anatop is used in clock drivers as it controls the internal PLLs
This will move the macro from asm/arch-imxrt to the device tree.
This presumably should also be done with the other IMX boards as well.

Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
2022-04-12 21:08:23 +02:00
Marek Vasut
c8009c1527 mmc: fsl_esdhc_imx: Add i.MX8MP compatible string
Add compatible string for i.MX8MP, which permits i.MX8MP to use
HS400ES mode, just like all the other i.MX8M.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Haibo Chen <haibo.chen@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
2022-04-12 21:08:23 +02:00
Marek Vasut
e1aad512a6 spi: nxp_fspi: Add i.MX8MP compatible string
The i.MX8M Mini and i.MX8M Plus flexspi IPs are compatible with one
another, however the linux kernel DT uses separate compatible string
for each SoC. Add the missing i.MX8MP compatible into this driver.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
2022-04-12 21:08:23 +02:00
Michael Trimarchi
a2f5c9366a net: phy: nxp-tja11xx: Add NXP TJA11xx PHY driver
Add driver for the NXP TJA1100 and TJA1101 PHYs. These PHYs are special
BroadRReach 100BaseT1 PHYs used in automotive.

Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
2022-04-12 19:10:44 +02:00
Ariel D'Alessandro
087baf80ec net: phy: Add phy_modify() accessor
Add read-modify-write unlocked accessor for accessing a PHY register.

Signed-off-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
2022-04-12 19:10:44 +02:00
Ariel D'Alessandro
d7db0e6df3 iopoll: Extend read_poll_timeout macro to support variable parameters
This macro currently supports only one parameter. Based on Linux iopoll,
let's extend read_poll_timeout common API to allow multiple variable
parameters.

Signed-off-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
2022-04-12 19:10:44 +02:00
Ariel D'Alessandro
01c67a381c phy: nxp-c45-tja11xx: Rename functions to be c45 tja11xx specific
This driver supports NXP C45 TJA11XX PHYs, but there're also other NXP
TJA11XX PHYs. Let's rename functions in this driver to be c45 variant
specific, so further drivers can be introduced adding support for NXP
TJA11XX PHYs.

Signed-off-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
2022-04-12 19:10:44 +02:00
Tommaso Merciai
d101661087 driver: pwm: pwm-imx: separe dm from non dm implementation
Separe dm implementation from non dm implementation of pwm-imx
driver using CONFIG_DM_PWM

Signed-off-by: Tommaso Merciai <tommaso.merciai@amarulasolutions.com>
2022-04-12 19:10:44 +02:00
Tommaso Merciai
2c432563df drivers: pwm: pwm-imx: move pwm-imx-util into pwm-imx
Move pwm_imx_get_parms, pwm_id_to_reg functions into pwm-imx.c
and drop off pwm-imx-util.c

Signed-off-by: Tommaso Merciai <tommaso.merciai@amarulasolutions.com>
2022-04-12 19:10:44 +02:00
Philippe Schenker
f3b5100aff regulator: fixed: add possibility to enable by clock
This commit adds the possibility to choose the compatible
"regulator-fixed-clock" in devicetree.

This is a special case of regulator-fixed where a clock has to
be used to switch the regulator on and off.

Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2022-04-12 19:10:44 +02:00
Peng Fan
ed6ba46e3b misc: imx8ulp: Update fuse driver
- According to S400 API, the fuse bank 25 (Testconfig2) is able to
access. Add it into driver's mapping table.
- According to FSB words list, the reserved 48 words are ahead of
the bank 5 and bank 6. Fix the wrong position.

Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-04-12 19:10:43 +02:00
Ye Li
203412f66d misc: S400_API: Update S400 API for buffer dump
Add ahab_dump_buffer API to dump AHAB buffer for debug purpose

Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-04-12 17:33:57 +02:00
Clement Faure
a55ca506c9 misc: S400_API: add ahab_release_caam
Add ahab_release_caam() function to the S400 API.

Signed-off-by: Clement Faure <clement.faure@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-04-12 17:33:56 +02:00
Ye Li
043d11a459 misc: imx8ulp: Add OEM SRK Hash fuse support
Since latest S400 firmware has supported to read OEM SRK Hash, add
it to the driver's table

Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-04-12 17:33:56 +02:00
Marek Vasut
77ee5d3508 phy: phy-imx8mq-usb: Add support for i.MX8MP USB PHY
Add initial support for i.MX8MP USB PHY, i.MX8MP USB is similar to
the i.MX8MQ, except for clock and power domain design customization.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Tested-By: Tim Harvey <tharvey@gateworks.com> #imx8mp-venice-gw74xx
2022-04-12 17:33:56 +02:00
Marek Vasut
7a2c3be95a clk: imx8mp: Fill in DWC3 USB, USB PHY, HSIOMIX clock
Add clock tables required to bring up DWC3 USB, USB PHY and HSIOMIX domain.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2022-04-12 17:33:56 +02:00
Angus Ainslie
129f5102d2 clk: imx8m: reduce rate table duplication
Re-factor the imx8m[nmpq] rate tables into the common pll1416x clock
driver.

43cdaa1567ad3 ("clk: imx8mm: Move 1443X/1416X PLL clock structure to common place")

Signed-off-by: Angus Ainslie <angus@akkea.ca>
Tested-by: Adam Ford <aford173@gmail.com> #imx8mm-beacon
2022-04-12 17:33:55 +02:00
Angus Ainslie
11c8ab01f3 clk: imx8mq: Add a clock driver for the imx8mq
This is a DM clock driver based off the imx8mm u-boot driver and the linux
kernel driver.

All of the PLLs and clocks are initialized so the subsystems below are
functional and tested.

1) USB host and peripheral
2) ECSPI
3) UART
4) I2C all busses
5) USDHC for eMMC support
6) USB storage
7) GPIO
8) DRAM

Signed-off-by: Angus Ainslie <angus@akkea.ca>
Acked-by: Sean Anderson <seanga2@gmail.com>
2022-04-12 17:33:55 +02:00
Ye Li
34793598c8 mtd: nand: mxs_nand_spl: Remove the page aligned access
The mxs_nand_spl driver can support to read from page unaligned offset,
so don't need to set bl_len to ask spl_load_simple_fit to handle
the page unaligned access.

Actually spl_load_simple_fit has two parts of reading:
spl_simple_fit_read and spl_load_fit_image.
The spl_load_fit_image can handle the page unaligned offset,
but the spl_simple_fit_read can't do it. spl_simple_fit_read requires
the FIT location at page aligned offset.

Hence, remove the nand_get_mtd overwrite function from mxs_nand_spl
to use page unaligned read by driver.

Signed-off-by: Ye Li <ye.li@nxp.com>
Tested-by: Tim Harvey <tharvey@gateworks.com> #gw_ventana
2022-04-12 17:33:55 +02:00
Tommaso Merciai
6828b3ecea driver: pwm: pwm-imx: introduce pwm_dm_imx_get_parms
Introduce pwm_dm_imx_get_parms, dm version of pwm_imx_get_parms.
This function get clock rate using clk dm api

Signed-off-by: Tommaso Merciai <tommaso.merciai@amarulasolutions.com>
2022-04-12 17:33:55 +02:00
Tommaso Merciai
bfc778cb93 driver: pwm: pwm-imx: get and enable per/ipg clock using dm
Get and enable ipg/per pwms clocks using dm api into imx_pwm_of_to_plat
and imx_pwm_probe driver function

Signed-off-by: Tommaso Merciai <tommaso.merciai@amarulasolutions.com>
2022-04-12 17:33:55 +02:00
Tommaso Merciai
e2d074cead clk: imx8mm: add pwm clocks support
Add clocks support for the PWM controllers. This is ported from
Linux v5.17-rc8.

Signed-off-by: Tommaso Merciai <tommaso.merciai@amarulasolutions.com>
2022-04-12 17:33:55 +02:00
Tim Harvey
8479b9e6c9 drivers: misc: add Gateworks System Controller driver
Add a driver for the Gateworks System Controller used on Gateworks boards
which provides a boot watchdog, power control, temperature monitor,
and voltage ADCs.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2022-04-12 15:36:17 +02:00
Marek Vasut
b8a24e07b2 imx8m: ddrphy_utils: Add 3732 MT/s mode
Add entry for 3732 MT/s mode of operation of the LPDDR4, in
which case the DDR PLL has to be configured in 933 MHz mode.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
2022-04-12 15:36:17 +02:00
Marek Vasut
a0044538c8 pmic: pca9450: Add PCA9450C compatible string
Add DT compatible string for PCA9450C PMIC. This is a variant of the
PCA9450 PMIC with 6 A dual-phase buck regulator and 3 A buck regulator,
and is software-wise compatible with the PCA9450B. This variant of the
PCA9450 is designed for use as companion PMIC for i.MX8MP.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2022-04-12 15:36:17 +02:00
Marek Vasut
3fa3f23d1b ARM: dts: net: dwc_eth_qos: Fix i.MX8MP compatible string
The correct compatible string for i.MX8MP variant of DWC EQoS MAC
is "nxp,imx8mp-dwmac-eqos", use it. Drop the two current users of
the current wrong compatible string to avoid breaking them.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
2022-04-12 15:36:17 +02:00
Angus Ainslie
9eb5e7d9ab pinctrl: nxp: don't automatically select DEVRES
If we select DEVRES here then it breaks building an imx8m SPL without
DEVRES support.

Signed-off-by: Angus Ainslie <angus@akkea.ca>
2022-04-12 15:36:17 +02:00
Gaurav Jain
cb5d0419f5 crypto/fsl: i.MX8: Enable Job ring driver model.
i.MX8(QM/QXP) - added support for JR driver model.
sec is initialized based on job ring information processed
from device tree.

Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
2022-04-12 11:19:21 +02:00
Gaurav Jain
4556cf8271 crypto/fsl: Add support for CAAM Job ring driver model
added device tree support for job ring driver.
sec is initialized based on job ring information processed
from device tree.

Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2022-04-12 11:18:34 +02:00
Hajo Noerenberg
c3322a53f3 ahci: add PCI bindings for Marvell 88SE6121/45 SATA controllers
Add AHCI PCI bindings for Marvell 88SE6121/45 SATA controllers.

The 88SE6121 controller is used, for example, in the Seagate Blackarmor NAS440 or the Iomega ix4-200d NAS.

As Pali Rohár explained [1], these controllers do not match the standard AHCI class code and therefore require an explizit PCI binding. The Linux kernel also uses this approach [2].

[1] https://lists.denx.de/pipermail/u-boot/2022-March/479197.html
[2] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/drivers/ata/ahci.c?h=v5.17#n557

Signed-off-by: Hajo Noerenberg <hajo-uboot@noerenberg.de>
Reviewed-by: Pali Rohár <pali@kernel.org>
2022-04-11 15:03:29 -04:00
Patrice Chotard
7ab3364c6d mtd: Update the way partitions are parsed
In case mtd_info's dev field is not populated (raw nand's case),
use the flash_node new field which reference the DT flash node where
can be found "partitions" node with "fixed-partitions" compatible.

Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>

Cc: Farhan Ali <farhan.ali@broadcom.com>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Marek Behun <marek.behun@nic.cz>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Wolfgang Denk <wd@denx.de>
2022-04-11 11:39:19 -04:00
Patrice Chotard
c86a4de8df mtd: Add flash_node in struct mtd_info
Currently, add_mtd_partitions_of() can be used only if dev field of
mtd_info struct is populated. It's the case, for example, for a spi nor
flash, which has a DT compatible "jedec,spi-nor" and an associated
device. mtd->dev is populated in spi_nor_scan().

But in case of a raw nand node, mtd_info's dev field can't be populated
as flash node has no compatible, so no associated device.
add_mtd_partitions_of() can't be used to parse "partitions" subnode.

To remove this constraint, add an ofnode field in mtd_info struct
which reference the DT flash node. This new field is populated by
nand_scan_tail(). This new field will be used by add_mtd_partitions_of()
to parse the flash node for "partitions" defined in DT.

Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Farhan Ali <farhan.ali@broadcom.com>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Marek Behun <marek.behun@nic.cz>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Wolfgang Denk <wd@denx.de>
2022-04-11 11:39:19 -04:00
Paul HENRYS
877de2a369 drivers: led: bcm6858: Set a default brightness when probing LEDs
When probing the LEDs, a default brightness is set based on settings
from the U-Boot device tree, i.e. the 'default-brightness' property
of the LED nodes. If that property is not present, the default
maximum brightness is set.
This should make sure the LED controller's registers affecting the
brightness are correctly initialized and should give a consistent
behaviour.

Signed-off-by: Paul HENRYS <paul.henrys_ext@softathome.com>
2022-04-11 11:39:19 -04:00
Ivan Vozvakhov
067cfc1c2e led: led_pwm: Add a driver for LEDs connected to PWM
Add a driver which allows to use of LEDs connected
to PWM (Linux compatible).
MAINTAINERS: add i.vozvakhov as a maintainer of leds-pwm
C(required during new functionality adding).

Signed-off-by: Ivan Vozvakhov <i.vozvakhov@corp.mail.ru>
2022-04-11 11:39:19 -04:00
Patrick Delaunay
70812bb83d tee: optee: bind rng optee driver
In U-Boot, the discovery of TA based on its UUID on the TEE bus is
not supported.

This patch only binds the driver associated to the new supported
OP-TEE TA = TA_HWRNG when this driver is enable.

Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
2022-04-11 10:28:04 -04:00
Patrick Delaunay
fd52e7f9c7 rng: add OP-TEE based Random Number Generator
Add driver for OP-TEE based Random Number Generator on ARM SoCs
where hardware entropy sources are not accessible to normal world
and the RNG service is provided by a HWRNG Trusted Application (TA).

This driver is based on the linux driver: char/hw_random/optee-rng.c

Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
2022-04-11 10:28:04 -04:00
Tom Rini
33ae8c5beb Pull request for efi-2022-07-rc1
Documentation:
 
 * Describe how enable DM_SERIAL for a board
 
 UEFI
 
 * Preparatory patches for better integration of DM and UEFI
 * Use sysreset after capsule updates instead of do_reset
 * Allow to disable persisting non-volatile variables
 -----BEGIN PGP SIGNATURE-----
 
 iQIzBAABCAAdFiEEbcT5xx8ppvoGt20zxIHbvCwFGsQFAmJSiD8ACgkQxIHbvCwF
 GsQ5FRAAhjV2q+ZawfNRkLQTI+pr/SZFH/H/LypWex8uXO6Enx8QvMU96RBMbtQI
 /LbduYDmRfhFbX2L5x+xV7feoMwvP+AOE4xmD55yuuWzmQttgEyGfwQY+mQYg3GU
 PwNkBUVN1msoOq7OFjevlk406VvnpYqvAuen1H66m0HkRe73hYucrZnt6Wxy+p+F
 fZdIaVpZc97jVHpLGNJBYg9JpUEkEeIcRaeUQHFIys/wZOiWWyTshYNLKQmfN3oV
 qNm0iDZMcqCk4XYkQR8R4IjXTHejtgGcKZaQfoLEYONpDOjG+X+nAviJaQ3BLoSK
 6+p3UhsoPgA0fT7sZg0dSn73f1xM7njDLhnR2JlZbKxDsV8SCA7+J/q7dElMX9Ld
 9/BwzqwU4WpJh4whRdpTFkcRY1ytnBBwltNo9sRm89QfHFIuT9+Rxf6s8GAcbCNU
 Pb6P6u44BkAGZG7hCUa3swh0EORISAxVhDJEEf4eWNlKHYE2A3dDFsLioGPPRoPS
 RNpXcTfz3cT2E8buDGUefKKCP+9dzSRP5HLHasibfC6LdIaR0aKTS7a1S+C0jjwj
 1W+GeStyGKzM+8hq5OREsAfCMRIs9bLq3vs+f7aPPn/FIgebLJmGFykswRQiQTAt
 B4wArS79APrqBini887EPF9LoNTtdnRCst+xmMHxVEW0yyDwZWk=
 =SxkC
 -----END PGP SIGNATURE-----

Merge tag 'efi-2022-07-rc1' of https://source.denx.de/u-boot/custodians/u-boot-efi

Pull request for efi-2022-07-rc1

Documentation:

* Describe how enable DM_SERIAL for a board

UEFI

* Preparatory patches for better integration of DM and UEFI
* Use sysreset after capsule updates instead of do_reset
* Allow to disable persisting non-volatile variables
2022-04-10 11:21:39 -04:00
Nate Drude
d79f1a8569 phy: adin: add driver for Analog Devices ADIN1300 PHY
The current implementation configures RGMII using device tree phy-mode
property and then calls genphy_config

adin_config_rgmii_mode is derived from:
https://github.com/varigit/linux-imx/blob/lf-5.10.y_var04/drivers/net/phy/adin.c#L218-L262

Signed-off-by: Nate Drude <nate.d@variscite.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
2022-04-10 08:44:13 +03:00
Tim Harvey
f3409d7ae6 net: eth-phy: prevent undesired de-assertion of phy-reset on request
When gpio_request_by_name allocates a gpio output it by default will
de-assert the gpio which for phy-reset will take the PHY out of reset.
As this occurs before eth_phy_reset is called to assert the reset
line it can cause undesired affects if reset timings are not properly
met.

Configure the gpio with GPIOD_IS_OUT_ACTIVE so that reset is kept active
(reset asserted) to avoid this.

Cc: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
2022-04-10 08:44:13 +03:00
Tim Harvey
4223fb0ee1 net: fec: prevent undesired de-assertion of phy-reset on request
When gpio_request_by_name allocates a gpio output it by default will
de-assert the gpio which for phy-reset will take the PHY out of reset.
As this occurs before fec_gpio_reset is called to assert the reset
line it can cause undesired affects if reset timings are not properly
met.

Configure the gpio with GPIOD_IS_OUT_ACTIVE so that reset is kept active
(reset asserted) to avoid this.

Cc: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Adam Ford <aford173@gmail.com> #imx8mm-beacon
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
2022-04-10 08:44:13 +03:00
Marek Behún
e24b58f5ed net: phy: don't require PHY interface mode during PHY creation
Currently we require PHY interface mode to be known when
finding/creating the PHY - the functions
  * phy_connect_phy_id()
  * phy_device_create()
  * create_phy_by_mask()
  * search_for_existing_phy()
  * get_phy_device_by_mask()
  * phy_find_by_mask()
all require the interface parameter, but the only thing done with it is
that it is assigned to phydev->interface.

This makes it impossible to find a PHY device without overwriting the
set mode.

Since the interface mode is not used during .probe() and should be used
at first in .config(), drop the interface parameter from these
functions. Make the default value of phydev->interface (in
phy_device_create()) to be PHY_INTERFACE_MODE_NA. Move the interface
parameter to phy_connect_dev(), where it should be.

Change all occurrences treewide. In occurrences where we don't call
phy_connect_dev() for some reason (they only configure the PHY without
connecting it to an ethernet controller), set
  phydev->interface = value from phy_find_by_mask call.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
2022-04-10 08:44:13 +03:00
Marek Behún
b638814e91 bcmgenet, sun8i_emac: Don't connect PHY two times
The bcmgenet and sun8i_emac drivers call phy_connect(), which finds /
creates the PHY and also connects it to the eth device via
phy_connect_dev(), then set some phydev members (bcmgenet only), and
then call phy_connect_dev() explicitly again.

Drop the second phy_connect_dev(), since it is unnecesary.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
2022-04-10 08:44:13 +03:00
Marek Behún
79bef5fb1f net: phy: use ->is_c45 instead of is_10g_interface()
Use phydev->is_c45 instead of is_10g_interface(phydev->interface) to
determine whether clause 45 protocol should be used.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
2022-04-10 08:44:13 +03:00
Marek Behún
f961b3abf8 net: phy: xilinx: Check interface type in ->config(), not ->probe()
We want to be able to have phydev->interface uninitialized during
->probe(). We should assume that phydev->interface is initialized only
before ->config().

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
2022-04-10 08:44:13 +03:00
Marek Behún
ffb0f6f488 treewide: Rename PHY_INTERFACE_MODE_NONE to PHY_INTERFACE_MODE_NA
Rename constant PHY_INTERFACE_MODE_NONE to PHY_INTERFACE_MODE_NA to make
it compatible with Linux' naming.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
2022-04-10 08:44:13 +03:00
Marek Behún
6706d7dcbe treewide: Rename PHY_INTERFACE_MODE_COUNT to PHY_INTERFACE_MODE_MAX
Rename constant PHY_INTERFACE_MODE_COUNT to PHY_INTERFACE_MODE_MAX to
make it compatible with Linux' naming.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
2022-04-10 08:44:13 +03:00
Marek Behún
123ca114e0 net: introduce helpers to get PHY interface mode from a device/ofnode
Add helpers ofnode_read_phy_mode() and dev_read_phy_mode() to parse the
"phy-mode" / "phy-connection-type" property. Add corresponding UT test.

Use them treewide.

This allows us to inline the phy_get_interface_by_name() into
ofnode_read_phy_mode(), since the former is not used anymore.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
2022-04-10 08:44:12 +03:00
Marek Behún
9c06b4815c net: phy: fix parsing wrong property
The "phy-interface-type" property should be "phy-connection-type".

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
2022-04-10 08:44:12 +03:00
Marek Behún
1776a24bbb treewide: use dm_mdio_read/write/reset() wrappers
Use the new dm_mdio_read/write/reset() wrappers treewide, instead of
always getting and dereferencing MDIO operations structure pointer.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
2022-04-10 08:44:12 +03:00
Marek Behún
f3dd213e15 net: introduce helpers to get PHY ofnode from MAC
Add helpers ofnode_get_phy_node() and dev_get_phy_node() and use it in
net/mdio-uclass.c function dm_eth_connect_phy_handle(). Also add
corresponding UT test.

This is useful because other part's of U-Boot may want to get PHY ofnode
without connecting a PHY.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2022-04-10 08:44:12 +03:00
Haolin Li
e2b6cf5cad net: phy: dp83867: Fix a never true comparison
The type of the return value of phy_read() and phy_read_mmd() is int.
Change the variable to not be unsigned so that we not get into an
unsigned compared against 0.

Signed-off-by: Haolin Li <li.haolin@qq.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
2022-04-10 08:44:12 +03:00
Vladimir Oltean
5faf161d07 net: phy: atheros: avoid error in ar803x_of_init() when PHY has no OF node
A DM_ETH driver may use phy_connect() towards a PHY address on an MDIO
bus which is not specified in the device tree, as evidenced by:

pfe_eth_probe
-> pfe_phy_configure
   -> phy_connect

When this happens, the PHY will have an invalid OF node.

When ar803x_config() runs, it silently fails at ar803x_of_init(), and
therefore, fails to run the rest of the initialization.

This makes MII_BMCR contain what it had after BMCR_RESET (0x8000) has
been written into it by phy_reset(). Since BMCR_RESET is volatile and
self-clearing, the MII_BMCR ends up having a value of 0x0. The further
configuration of this register, which is supposed to be handled by
genphy_config_aneg() lower in ar803x_config(), never gets a chance to
run due to this early error from ar803x_of_init().

As a result of having MII_BMCR as 0, the following symptom appears:

=> setenv ethact pfe_eth0
=> setenv ipaddr 10.0.0.1
=> ping 10.0.0.2
pfe_eth0 Waiting for PHY auto negotiation to complete......... TIMEOUT !
Could not initialize PHY pfe_eth0

Manually writing 0x1140 into register 0 of the PHY makes the connection
work, but it is rather desirable that the port works without any manual
intervention.

Fixes: fe6293a809 ("phy: atheros: add device tree bindings and config")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
2022-04-10 08:44:12 +03:00
Vladimir Oltean
107b14e36e net: phy: dp83867: avoid error in dp83867_of_init() when PHY has no OF node
A DM_ETH driver may use phy_connect() towards a PHY address on an MDIO
bus which is not specified in the device tree, as evidenced by:

pfe_eth_probe
-> pfe_phy_configure
   -> phy_connect

When this happens, the PHY will have an invalid OF node.

The dp83867_config() method has extra initialization steps which are
bypassed when the PHY lacks an OF node, which is undesirable because it
will lead to broken networking. Allow the rest of the code to run.

Fixes: 085445ca41 ("net: phy: ti: Allow the driver to be more configurable")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
2022-04-10 08:44:12 +03:00
AKASHI Takahiro
6b7a6210fd dm: add tag support
With dm-tag feature, any U-Boot subsystem is allowed to associate
arbitrary number of data with a particular udevice. This can been
see as expanding "struct udevice" without modifying the definition.

As a first user, UEFI subsystem makes use of tags to associate
an efi_disk object with a block device.

Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
2022-04-09 21:06:31 +02:00
AKASHI Takahiro
4c73b03442 block: ide: call device_probe() after scanning
Every time an ide bus/port is scanned and a new device is detected,
we want to call device_probe() as it will give us a chance to run
additional post-processings for some purposes.

In particular, support for creating partitions on a device will be added.

Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
2022-04-09 21:06:31 +02:00
AKASHI Takahiro
c662edd6de sata: call device_probe() after scanning
Every time a sata bus/port is scanned and a new device is detected,
we want to call device_probe() as it will give us a chance to run
additional post-processings for some purposes.

In particular, support for creating partitions on a device will be added.

Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
2022-04-09 21:06:31 +02:00
AKASHI Takahiro
df1ed8b2a8 nvme: call device_probe() after scanning
Every time a nvme bus/port is scanned and a new device is detected,
we want to call device_probe() as it will give us a chance to run
additional post-processings for some purposes.

In particular, support for creating partitions on a device will be added.

Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
2022-04-09 21:06:31 +02:00
AKASHI Takahiro
c822c1a50b mmc: call device_probe() after scanning
Every time a mmc bus/port is scanned and a new device is detected,
we want to call device_probe() as it will give us a chance to run
additional post-processings for some purposes.

In particular, support for creating partitions on a device will be added.

Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2022-04-09 21:06:31 +02:00
AKASHI Takahiro
ae518bd880 scsi: call device_probe() after scanning
Every time a scsi bus/port is scanned and a new block device is detected,
we want to call device_probe() as it will give us a chance to run
additional post-processings for some purposes.

In particular, support for creating partitions on a device will be added.

Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
2022-04-09 21:06:31 +02:00
Luca Ellero
c170fe0a77 gpio: pca953x_gpio: add PCA957X support
Take as reference Linux kernel code:
	drivers/gpio/gpio-pca953x.c

Signed-off-by: Luca Ellero <l.ellero@asem.it>
Reviewed-by: Simon Glass <sjg@chromium.org>
2022-04-08 22:51:48 -04:00
Eddie James
1d99e673c7 gpio: Enable hogging support in SPL
Use the CONFIG macros to conditionally build the GPIO hogging support in
either the SPL or U-Boot, or both, depending on the configuration. Also
call the GPIO hog probe function in the common SPL board initialization
as an equivalent to adding it to the U-Boot init sequence functions.

Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2022-04-08 22:51:48 -04:00
Andrew Jeffery
34be6968c3 gpio: Add gpio_request_by_line_name()
Add support for the upstream gpio-line-names property already described
in the common GPIO binding document[1]. The ability to search for a line
name allows boards to lift the implementation of common GPIO behaviours
away from specific line indexes on a GPIO controller.

[1] 3c35bfee83/dtschema/schemas/gpio/gpio.yaml (L17)

Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
2022-04-08 15:17:23 -04:00
Tom Rini
2fc0995cc0 arm: Remove unused ep93xx code
There are no platforms for this architecture anymore, remove unused
code.

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-04-08 10:46:22 -04:00
Tom Rini
9035caf080 net: Remove uli526x driver
This driver is not enabled by any board and not converted to DM_ETH.
Remove.

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-04-08 10:46:22 -04:00
Tom Rini
0467b3b3ae net: Remove ns8382x driver
This driver is not enabled by any board and not converted to DM_ETH.
Remove.

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-04-08 10:46:22 -04:00
Tom Rini
4c5469645d net: Remove natsemi driver
This driver is not enabled by any board and not converted to DM_ETH.
Remove.

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-04-08 10:46:22 -04:00
Tom Rini
9bd2ab4b39 net: Remove lan91c96 driver
This driver is not enabled by any board and not converted to DM_ETH.
Remove.

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-04-08 10:46:22 -04:00
Tom Rini
2e808fadf6 net: Remove ftmac110 driver
This driver is not enabled by any board and not converted to DM_ETH.
Remove.

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-04-08 10:46:22 -04:00
Tom Rini
acae10dc3e net: Remove dnet driver
This driver is not enabled by any board and not converted to DM_ETH.
Remove.

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-04-08 10:46:22 -04:00
Tom Rini
f693a921a3 net: Remove cs8900 driver
This driver is not enabled by any board and not converted to DM_ETH.
Remove.

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-04-08 10:46:22 -04:00
Tom Rini
122126adbd net: Remove ax88180 driver
This driver is not enabled by any board and not converted to DM_ETH.
Remove.

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-04-08 10:46:22 -04:00
Tom Rini
53b666b76f net: Remove armada100_fec driver
This driver is not enabled by any board and not converted to DM_ETH.
Remove.

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-04-08 10:46:22 -04:00
Tom Rini
388de0fa8b Convert CONFIG_DIMM_SLOTS_PER_CTLR to Kconfig
This converts the following to Kconfig:
   CONFIG_DIMM_SLOTS_PER_CTLR

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-04-08 10:46:22 -04:00
Tom Rini
55b3ba4c2b spi: cadence_qspi: Migrate CONFIG_CQSPI_REF_CLK to Kconfig
This is a little tricky since SoCFPGA has code to determine this as
runtime.  Introduce a guard variable for platforms to select if they
have a static value to use.  Then for ARCH_SOCFPGA, call
cm_get_qspi_controller_clk_hz() and otherwise continue the previous
behavior.

Cc: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2022-04-08 10:46:22 -04:00
Tom Rini
5d14c336b2 Convert CONFIG_SH_SCIF_CLK_FREQ to Kconfig
This converts the following to Kconfig:
   CONFIG_SH_SCIF_CLK_FREQ

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-04-08 09:06:46 -04:00
Tom Rini
f9f3209a34 Convert CONFIG_CONS_SCIF0 et al to Kconfig
This converts the following to Kconfig:
   CONFIG_CONS_SCIF0
   CONFIG_CONS_SCIF1
   CONFIG_CONS_SCIF2
   CONFIG_CONS_SCIF4
   CONFIG_CONS_SCIFA0

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-04-08 09:06:28 -04:00
Simon Glass
49e8668181 dm: blk: Expand iteration and add tests
Add some functions which support iteration before probing. Also add tests
for the functions.

Signed-off-by: Simon Glass <sjg@chromium.org>
2022-04-06 14:03:17 -04:00
Simon Glass
564e532eea spi: Avoid checking console in SPL
When SPI flash is used in SPL there is no console, so ctrlc() cannot be
called. Add a condition to fix this.

Signed-off-by: Simon Glass <sjg@chromium.org>
2022-04-06 14:01:42 -04:00
Lukasz Majewski
e8cb4e78c7 power: pmic: Provide DM_PMIC support for tps65217 driver
The tps65217 PMIC driver is used with am335x SoC based designs.

It is used in the SPL (MLO) as well, so the DM conversion only is
for u-boot proper.

This driver only allows simple reading/writing/dumping of the content
of its registers and requires the DM_I2C for proper operation.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2022-04-05 15:51:52 -04:00
Lukasz Majewski
1610b68ea3 power: Rename CONFIG_POWER_TPS65217 with CONFIG_PMIC_TPS65217
Up till now the CONFIG_POWER_TPS65217 has been defined in several header
files for am335x SoC.

This patch renames it to CONFIG_PMIC_TPS65217, which better reflects the
role of this IC circuit.

Moreover, new CONFIG_PMIC_TPS65217 has been introduced in Kconfig
to be used with boards, which both support DM_PMIC and DM_I2C.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
[trini: Migrate all other platforms as well]
Signed-off-by: Tom Rini <trini@konsulko.com>
2022-04-05 15:51:46 -04:00
Tom Rini
59bffec43a Merge branch '2022-04-04-platform-updates'
- Updates for exynos78x0 and TI K3 platforms
2022-04-05 13:45:22 -04:00
Tom Rini
037ef53cf0 Xilinx changes for v2022.07-rc1 v2
xilinx:
 - Allow booting bigger kernels till 100MB
 
 zynqmp:
 - DT updates (reset IDs)
 - Remove unneeded low level uart initialization from psu_init*
 - Enable PWM features
 - Add support for 1EG device
 
 serial_zynq:
 - Change fifo behavior in DEBUG mode
 
 zynq_sdhci:
 - Fix BASECLK setting calculation
 
 clk_zynqmp:
 - Add support for showing video clock
 
 gpio:
 - Update slg driver to handle DT flags
 
 net:
 - Update ethernet_id code to support also DM_ETH_PHY
 - Add support for DM_ETH_PHY in gem driver
 - Enable dynamic mode for SGMII config in gem driver
 
 pwm:
 - Add driver for cadence PWM
 
 versal:
 - Add support for reserved memory
 
 firmware:
 - Handle PD enabling for SPL
 - Add support for IOUSLCR SGMII configurations
 
 include:
 - Sync phy.h with Linux
 - Update xilinx power domain dt binding headers
 -----BEGIN PGP SIGNATURE-----
 
 iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYkxUZwAKCRDKSWXLKUoM
 IXJ2AKCQcoFK7wanCCvZfuEJCSwO5E4eCACginE2CFVXKcY1P8ta4ESusjY2TH0=
 =HOoS
 -----END PGP SIGNATURE-----

Merge tag 'xilinx-for-v2022.07-rc1-v2' of https://source.denx.de/u-boot/custodians/u-boot-microblaze

Xilinx changes for v2022.07-rc1 v2

xilinx:
- Allow booting bigger kernels till 100MB

zynqmp:
- DT updates (reset IDs)
- Remove unneeded low level uart initialization from psu_init*
- Enable PWM features
- Add support for 1EG device

serial_zynq:
- Change fifo behavior in DEBUG mode

zynq_sdhci:
- Fix BASECLK setting calculation

clk_zynqmp:
- Add support for showing video clock

gpio:
- Update slg driver to handle DT flags

net:
- Update ethernet_id code to support also DM_ETH_PHY
- Add support for DM_ETH_PHY in gem driver
- Enable dynamic mode for SGMII config in gem driver

pwm:
- Add driver for cadence PWM

versal:
- Add support for reserved memory

firmware:
- Handle PD enabling for SPL
- Add support for IOUSLCR SGMII configurations

include:
- Sync phy.h with Linux
- Update xilinx power domain dt binding headers
2022-04-05 11:27:39 -04:00
T Karthik Reddy
a7379ba650 net: zynq_gem: Add SGMII dynamic config support
Add support for SGMII dynamic configuration which will takes care of
configuring SGMII in the GEM secure (GEM_CLK_CTRL) configuration
register.

Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/a8915186e44015959978d080a31de652f544cd4a.1648631275.git.michal.simek@xilinx.com
2022-04-05 15:13:13 +02:00
T Karthik Reddy
7011efce23 firmware: firmware-zynqmp: Add zynqmp_pm_set_gem_config api
Add zynqmp_pm_set_gem_config() api to configure GEM secure registers.

Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/f69e32355c6a6be7d2780663353c52757530207d.1648631275.git.michal.simek@xilinx.com
2022-04-05 15:13:13 +02:00
T Karthik Reddy
e949e78948 gpio: slg7xl45106: Update gpio desc flags from DT
In current slg7xl45106 gpio driver xlate() function we are not updating
gpio flags from DT. Read the given flag from DT and update the gpio desc
flags variable with required gpio direction state.

Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/a8d7b4799337bd99f61ace509889f02b192a9414.1648631275.git.michal.simek@xilinx.com
2022-04-05 15:13:13 +02:00
T Karthik Reddy
fc6e56283e net: zynq_gem: Move ethernet info print statement
As we are not reading the PHY address in case of CONFIG_ETH_PHY in plat
function, phy address always prints as -1. So move the ethernet info
print statement to probe function, to display proper phy address.

Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/f6efc6719d767b1bebe65987c22c6d52329f4225.1648631275.git.michal.simek@xilinx.com
2022-04-05 15:13:13 +02:00
T Karthik Reddy
ccc8656f7f net: phy: Avoid phy gpio reset sequence if DM_ETH_PHY is enabled
If DM_ETH_PHY config is enabled PHY gpio reset is taken care by the
eth-phy-uclass driver, so use the PHY gpio reset functionality from
ethernet_id file when this config is disabled to reset the PHY.
Use debug() print instead of dev_err() to avoid warning incase if phy-id
compatible string is not present.

Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/4d0fd3f9f886c1d943776025e5efb5438b0eb389.1648631275.git.michal.simek@xilinx.com
2022-04-05 15:13:13 +02:00
Michal Simek
801725395a net: zynq_gem: Use shared MDIO bus support for zynqmp
CONFIG_ETH_PHY enables support to utilize generic ethernet phy
framework. Though if ethernet PHY node is in other ethernet node, it
will use shared MDIO to access the PHY of other ethernet.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Link: https://lore.kernel.org/r/337b1a38ba36cde1951739af62fb3d2736d97f53.1648631275.git.michal.simek@xilinx.com
2022-04-05 15:13:13 +02:00
T Karthik Reddy
9b529a972d net: phy: Fix rgmii-id phy reset timeout issue
While creating a phy device using phy_device_create(), we need to
provide a valid phyaddr instead of 0 causing phy address being
registered as 0 with mdio bus and shows mdio phy list as below

ZynqMP>  mdio list
eth0:
0 - TI DP83867 <--> ethernet@ff0b0000
eth1:
0 - TI DP83867 <--> ethernet@ff0c0000

Also PHY soft reset is being requested on 0 instead of valid
address causing "PHY reset timed out" error.

So add phyaddr argument to phy_connect_phy_id() and to its prototype
to create phy device with valid phyaddress.

Fixes: a744a284e3 ("net: phy: Add support for ethernet-phy-id with gpio reset")
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Link: https://lore.kernel.org/r/fe35fddb9faa5af577ffdfabaec6879c935a30f8.1648562755.git.michal.simek@xilinx.com
2022-04-05 15:10:54 +02:00
Michal Simek
6f735e4178 clk: zynqmp: Add support for for DP audio/video clocks
Add support for getting rate for DP audio and video clocks.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/8792efe1fd9715f7c8a2e1e24f0454fb5b25d833.1648552434.git.michal.simek@xilinx.com
2022-04-05 15:09:47 +02:00
Tom Rini
4de720e98d Merge branch 'master' of https://source.denx.de/u-boot/custodians/u-boot-sunxi
A big part is the DM pinctrl driver, which allows us to get rid of quite
some custom pinmux code and make the whole port much more robust. Many
thanks to Samuel for that nice contribution! There are some more or less
cosmetic warnings about missing clocks right now, I will send the trivial
fixes for that later.
Another big chunk is the mkimage upgrade, which adds RISC-V and TOC0
(secure images) support. Both features are unused at the moment, but I
have an always-secure board that will use that once the DT lands in the
kernel.
On top of those big things we have some smaller fixes, improving the
I2C DM support, fixing some H6/H616 early clock setup and improving the
eMMC boot partition support.

The gitlab CI completed successfully, including the build test for all
161 sunxi boards. I also boot tested on a A64, A20, H3, H6, and F1C100
board. USB, SD card, eMMC, and Ethernet all work there (where applicable).
2022-04-05 08:33:32 -04:00
Christian Gmeiner
da61ee6625 ram: k3-am654: Make VTT regulator optional
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
2022-04-04 19:02:04 -04:00
Dominic Rath
e4901e6591 ram: k3-am654: Write all configuration values
Makes it possible to use 16-bit DDR memory.

Signed-off-by: Dominic Rath <rath@ibv-augsburg.net>
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
2022-04-04 19:02:04 -04:00
Dave Gerlach
f861ce90ca ram: k3-ddrss: Introduce ECC Functionality for full memory space
Introduce ECC Functionality for full memory space as implemented in the
DDRSS. The following is done to accomplish this:

 * Introduce a memory region "ss" to allow dt to provide DDRSS region,
   which is not the same as "ctl" which is the controller region.

 * Introduce a "ti,ecc-enable" flag which allows a memorycontroller
   instance to enable ecc.

 * Introduce functionality to properly program the DDRSS registers to
   enable ECC for the full DDR memory space if enabled with above flag.

 * Expose a k3_ddrss_ddr_fdt_fixup call to allow fixup of fdt blob to
   account from DDR memory that must be reserved for ECC operation.

Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
2022-04-04 19:02:04 -04:00
Dave Gerlach
71eb527476 ram: k3-ddrss: Rename ddrss_ss_regs to ddrss_ctl_regs
The current address being read from dt actually represents the ddrss_ctl
memory region, while ddrss_ss region is something else. Introduce
ddrss_ctl_regs and use it to free up ddrss_ss_regs for its proper
purpose later so that we can avoid confusion.

Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
2022-04-04 19:02:04 -04:00
Hari Nagalla
162a6f53a1 misc: k3_esm: Add functionality to set and route error events within K3SoC
Add functionality to enable, set priority to the input events and to
route to MCU ESM. On AM64x/AM62x devices, it is possible to route Main
ESM0 error events to MCU ESM. When these error events are routed to MCU
ESM high output, it can trigger the reset logic to reset the device,
when CTRLMMR_MCU_RST_CTRL:MCU_ESM_ERROR_RESET_EN_Z is set to '0'.

K3 based J7 devices (ex: J721e) also have ESM modules, and the changes
to the driver does not impact those devices.

Signed-off-by: Hari Nagalla <hnagalla@ti.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
2022-04-04 19:02:04 -04:00
Samuel Holland
f5bfe15750 i2c: sun8i_rsb: Add support for DM clocks and resets
Currently, clock/reset setup for this device is handled by a
platform-specific function and is intermixed with non-DM pinctrl
setup. Use the devicetree to get clocks/resets, which disentagles
it from the pinctrl setup in preparation for moving to DM_PINCTRL.

This also has the added benefit of picking the right clock/reset
bits for H6 and new SoCs that have a rearranged PRCM MMIO space.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2022-04-04 23:24:17 +01:00
Samuel Holland
c9dd3caae3 i2c: sun8i_rsb: Initialize chips in .child_pre_probe
Chips attached to the RSB bus require an initialization command before
they can be used. (Specifically, this command programs the chip's
runtime address.) The driver does this in its .probe_chip hook, under
the assumption that .probe_chip is called during child probe. This is
not the case; .probe_chip is only called by dm_i2c_probe, which is
intended for use by board-level code, not for chips with OF nodes.

Since this initialization command must be run before a child chip can be
used, do it before probing each child.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2022-04-04 23:24:17 +01:00
Samuel Holland
07c411346c i2c: sun6i_p2wi: Add support for DM clocks and resets
Currently, clock/reset setup for this device is handled by a
platform-specific function and is intermixed with non-DM pinctrl
setup. Use the devicetree to get clocks/resets, which disentagles
it from the pinctrl setup in preparation for moving to DM_PINCTRL.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2022-04-04 23:24:17 +01:00
Samuel Holland
48457f7ab0 i2c: sun6i_p2wi: Initialize chips in .child_pre_probe
Chips attached to the P2WI bus require an initialization command before
they can be used. (Specifically, this switches the chip from I2C mode
to P2WI mode.) The driver does this in its .probe_chip hook, under the
assumption that .probe_chip is called during child probe. This is not
the case; .probe_chip is only called by dm_i2c_probe, which is intended
for use by board-level code, not for chips with OF nodes.

Since this initialization command must be run before a child chip can be
used, do it before probing each child.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2022-04-04 23:24:17 +01:00
Samuel Holland
f64233e9a5 spi: sun4i_spi: Remove non-DM pin setup
This is now handled automatically by the pinctrl driver.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2022-04-04 23:24:17 +01:00
Samuel Holland
77834dcc5b pinctrl: sunxi: Add SPI0 pinmuxes
Pin lists and mux values were taken from the Linux drivers.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2022-04-04 23:24:17 +01:00
Samuel Holland
458e59da5d pwm: sunxi: Remove non-DM pin setup
This is now handled automatically by the pinctrl driver.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2022-04-04 23:24:17 +01:00
Samuel Holland
aa4823ce48 pinctrl: sunxi: Add the A64 PWM pinmux
This is the only possible mux setting for the A64's PWM peripheral.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2022-04-04 23:24:17 +01:00
Samuel Holland
7570c54e46 pinctrl: sunxi: Add MMC pinmuxes
Pin lists and mux values were taken from the Linux drivers.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2022-04-04 23:24:16 +01:00
Samuel Holland
af2ec35c41 i2c: sun8i_rsb: Only do non-DM pin setup for non-DM I2C
When the DM_I2C driver is loaded, the pin setup is done automatically
from the device tree by the pinctrl driver.

Clean up the code in the process: remove #ifdefs and recognize that the
pin configuration is the same for all sun8i/sun50i SoCs, not just those
which select CONFIG_MACH_SUN8I.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2022-04-04 23:24:16 +01:00
Samuel Holland
923d89316a i2c: sun6i_p2wi: Only do non-DM pin setup for non-DM I2C
When the DM_I2C driver is loaded, the pin setup is done automatically
from the device tree by the pinctrl driver.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2022-04-04 23:24:16 +01:00
Samuel Holland
4c8f11d4af pinctrl: sunxi: Add I2C pinmuxes
Where multiple options were available, the one matching board.c and the
device trees was chosen.

Pin lists and mux values were taken from the Linux drivers.

Signed-off-by: Samuel Holland <samuel@sholland.org>
[Andre: fixup H5 I2C1 pinmux]
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2022-04-04 23:24:16 +01:00
Samuel Holland
ae022e8366 net: sun8i_emac: Remove non-DM pin setup
This is now handled automatically by the pinctrl driver.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2022-04-04 23:24:16 +01:00
Samuel Holland
37b3de432f pinctrl: sunxi: Add sun8i EMAC pinmuxes
Pin lists and mux values were taken from the Linux drivers.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2022-04-04 23:24:16 +01:00
Samuel Holland
7a93644c69 pinctrl: sunxi: Add sunxi GMAC pinmuxes
Pin lists and mux values were taken from the Linux drivers.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2022-04-04 23:24:16 +01:00
Samuel Holland
12bd00aafc net: sunxi_emac: Remove non-DM pin setup
This is now handled automatically by the pinctrl driver.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2022-04-04 23:24:16 +01:00
Samuel Holland
fcdbbd68d3 pinctrl: sunxi: Add sun4i EMAC pinmuxes
Pin lists and mux values were taken from the Linux drivers.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2022-04-04 23:24:16 +01:00
Samuel Holland
470a7bdb61 pinctrl: sunxi: Add UART pinmuxes
This includes UART0 and R_UART (s_uart) on all supported platforms, plus
the additional UART configurations from arch/arm/mach-sunxi/board.c.

Pin lists and mux values were taken from the Linux drivers.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2022-04-04 23:24:16 +01:00
Samuel Holland
50c195ee85 sunxi: pinctrl: Implement pin configuration
The sunxi pinctrl hardware has bias and drive control. Add driver
support for configuring those options.

Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2022-04-04 23:24:01 +01:00
Samuel Holland
d4b388244a sunxi: pinctrl: Implement get_pin_muxing function
The pinmux command uses this function to display pinmux status.

Since the driver cannot map pin numbers to a list of supported
functions, only functions which are common across all pins can be
reported by name.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2022-04-04 23:24:01 +01:00
Samuel Holland
29babfd92b sunxi: pinctrl: Implement pin muxing functions
Implement the operations to get pin and function names, and to set the
mux for a pin. The pin count and pin names are calculated as if each
bank has the maximum number of pins. Function names are simply the index
into a list of { function name, mux value } pairs.

We assume all pins associated with a function use the same mux value for
that function. This is generally true within a group of pins on a single
port, but generally false when some peripheral can be muxed to multiple
ports. For example, A64 UART3 uses mux 3 on port D, and mux 2 on port H.
But all of the port D pins use the same mux value, and so do all of the
port H pins. This applies even when the pins for some function are not
contiguous, and when the lower-numbered mux values are unused. A good
example of both of these cases is SPI0 on most SoCs.

This strategy saves a lot of space (which is especially important for
SPL), but where the mux value for a certain function differs across
ports, it forces us to choose a single port for that function at build
time. Since almost all boards use the default (i.e. reference design)
pin muxes[1], this is unlikely to be a problem.

[1]: See commit dda9fa734f ("sunxi: Simplify MMC pinmux selection")

Signed-off-by: Samuel Holland <samuel@sholland.org>
[Andre: add comment summarising the commit message]
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2022-04-04 23:24:01 +01:00
Samuel Holland
b799eabc7e sunxi: pinctrl: Create the driver skeleton
Create a do-nothing driver for each sunxi pin controller variant.

Since only one driver can automatically bind to a DT node, since the
GPIO driver already requires a manual binding process, and since the
pinctrl driver needs access to some of the same information, refactor
the GPIO driver to be bound by the pinctrl driver. This commit should
cause no functional change.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2022-04-04 23:23:50 +01:00
Tom Rini
01f1ab67f3 Merge branch 'next'
Signed-off-by: Tom Rini <trini@konsulko.com>
2022-04-04 10:48:44 -04:00
Tom Rini
8221c52d88 First set of u-boot-at91 features for the 2022.07 cycle
-----BEGIN PGP SIGNATURE-----
 
 iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmJH28ocHGV1Z2VuLmhy
 aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyDv4B/9FBx95f7zR6WmguG05
 VyBchjphsRSuXHb7NieVNNEIpCJu+zw8YutngN2Q8KWIbM9o1OZnrNGxuKR9s+Px
 ivMXytGGsIa74XXhxv2boX151R1a5TG4UPf4Vn20qxmUiScE4FaoW5wQHG2vGqxd
 /LbzENNCA1A41/RGGysqyY8nQgOEY+Iass+OaHe7XjngcCfY5oY4IRqJ/Ak7ojkv
 Vm46i+KCTuyBlcMDjAwDsukSmzsujz2FyzZU1Uy62N8quEdXgrlIA/Yh4oarZ+BO
 5W/BJe1rClbnBkMJJn71GUlmnYrioYeUvxvIYwZWooe0Hgr+Iv1vOXv8aJ4hBsdc
 yoje
 =SwGu
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-at91-2022.07-a' of https://source.denx.de/u-boot/custodians/u-boot-at91 into next

First set of u-boot-at91 features for the 2022.07 cycle:

This feature set includes the new driver for the Atmel TCB timer,
alignment in DT for sama7g5 and sama7g5ek board, one Kconfig conversion
for external reset, and the usage of Galois tables from ROM for sama5d2
device.
2022-04-04 08:26:55 -04:00
Sean Anderson
7a76347189 serial: dm: Add support for puts
Some serial drivers can be vastly more efficient when printing multiple
characters at once. Non-DM serial has had a puts option for these sorts
of drivers; implement it for DM serial as well.

Because we have to add carriage returns, we can't just pass the whole
string directly to the serial driver. Instead, we print up to the
newline, then print a carriage return, and then continue on. This is
less efficient, but it is better than printing each character
individually. It also avoids having to allocate memory just to add a few
characters.

Drivers may perform short writes (such as filling a FIFO) and return the
number of characters written in len. We loop over them in the same way
that _serial_putc loops over putc.

This results in around sizeof(void *) growth for all boards with
DM_SERIAL. The full implementation takes around 140 bytes.

Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2022-04-01 16:56:54 -04:00
Sean Anderson
2332590c48 serial: smh: Initialize serial only if semihosting is enabled
If semihosting is disabled, then the user has no debugger attached, and
will not see any messages. Don't create a serial device in this
instance, to (hopefully) fall back on another working serial device.

Signed-off-by: Sean Anderson <sean.anderson@seco.com>
2022-04-01 16:56:53 -04:00
Sean Anderson
74d11d37e2 serial: Add semihosting driver
This adds a serial driver which uses semihosting calls to read and write
to the host's console. For convenience, if CONFIG_DM_SERIAL is enabled,
we will instantiate a serial driver. This allows users to enable this
driver (which has no physical device) without modifying their device
trees or board files. We also implement a non-DM driver for SPL, or for
much faster output in U-Boot proper.

There are three ways to print to the console:

Method              Baud
================== =====
smh_putc in a loop   170
smh_puts            1600
smh_write with :tt 20000
================== =====

These speeds were measured using a 175 character message with a J-Link
adapter. For reference, U-Boot typically prints around 2700 characters
during boot on this board. There are two major factors affecting the
speed of these functions. First, each breakpoint incurs a delay. Second,
each debugger memory transaction incurs a delay. smh_putc has a
breakpoint and memory transaction for every character. smh_puts has one
breakpoint, but still has to use a transaction for every character. This
is because we don't know the length up front, so OpenOCD has to check if
each character is nul. smh_write has only one breakpoint and one memory
transfer.

DM serial drivers can only implement a putc interface, so we are stuck
with the slowest API. Non-DM drivers can implement puts, which is vastly
more efficient. When the driver starts up, we try to open :tt. Since
this is an extension, this may fail. If it does, we fall back to
smh_puts. We don't check :semihosting-features, since there are
nonconforming implementations (OpenOCD) which don't implement it (but
*do* implement :tt).

Some semihosting implementations (QEMU) don't handle READC properly. To
work around this, we try to use open/read (much like for stdin) if
possible.

There is no non-blocking I/O available, so we don't implement pending.
This will cause __serial_tstc to always return true. If
CONFIG_SERIAL_RX_BUFFER is enabled, _serial_tstc will try and read
characters forever. To avoid this, we depend on this config being
disabled.

Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2022-04-01 15:03:13 -04:00
Tom Rini
225aaacf36 db-mv784mp-gp: Rename CONFIG_DB_784MP_GP to CONFIG_TARGET_DB_MV784MP_GP
The value CONFIG_DB_784MP_GP is only used in the DDR code to refer to
CONFIG_TARGET_DB_MV784MP_GP so just use that second value directly.

Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2022-04-01 10:28:47 -04:00
Tom Rini
db48e52584 Convert CONFIG_LPUART et al to Kconfig
This converts the following to Kconfig:
   CONFIG_LPUART
   CONFIG_LPUART_32B_REG

And note that CONFIG_LPUART_32B_REG is unused in code.

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-04-01 10:28:46 -04:00
Tom Rini
3c205a6e4a Convert CONFIG_MCFRTC et al to Kconfig
This converts the following to Kconfig:
   CONFIG_MCFRTC
   CONFIG_SYS_MCFRTC_BASE

While at it, remove '#undef RTC_DEBUG' from these config files.

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-04-01 10:28:46 -04:00
Tom Rini
448dfb407f Convert CONFIG_BITBANGMII_MULTI to Kconfig
This converts the following to Kconfig:
   CONFIG_BITBANGMII_MULTI

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-04-01 10:28:46 -04:00
Tom Rini
797c2b4a1a Convert CONFIG_BCM2835_GPIO to Kconfig
This converts the following to Kconfig:
   CONFIG_BCM2835_GPIO

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-04-01 10:28:46 -04:00
Clément Léger
70fb1ae9dd timer: atmel_tcb_timer: add atmel_tcb driver
Add a driver for the timer counter block that can be found on sama5d2.
This driver will be used when booting under OP-TEE since the pit timer
which is part of the SYSC is secured. Channel 1 & 2 are configured to
be chained together which allows to have a 64bits counter.

Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
2022-04-01 15:42:46 +03:00
Fabio Estevam
25a448333d video: Do not show splash and U-Boot logo simultaneously
Currently, on imx6sabresd and gwventana boards, the company logo
and U-Boot logo are shown.

The correct behavior is to show only the company logo, if available,
and not both logos.

Reported-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Tested-by: Tim Harvey <tharvey@gateworks.com> #gw_ventana
2022-03-31 08:27:51 -04:00
Sean Anderson
682e73d235 clk: Use generic CCF ops where possible
This converts most CCF drivers to use generic ops. imx6q is the only
outlier, where we retain the existing functionality by moving the check to
request().

Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20220320203446.740178-2-seanga2@gmail.com
[ fixed missing include for at91 ]
Signed-off-by: Sean Anderson <seanga2@gmail.com>
2022-03-30 14:18:56 -04:00
Sean Anderson
3a11b5ae65 clk: ccf: Add some helper functions for clock ops
Most CCF drivers follow a common pattern where their clock ops defer the
actual operation to the backing CCF clock. Add some generic implementations
of these functions to reduce duplication of code.

Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20220320203446.740178-1-seanga2@gmail.com
2022-03-30 13:03:29 -04:00
Sean Anderson
e7075ff7b3 clk: Consolidate some clock functions
These functions are exactly the same as their "nodev" varients, except they
accept a device and not an ofnode. Rewrite them to just call the other
function.

Signed-off-by: Sean Anderson <seanga2@gmail.com>
Link: https://lore.kernel.org/r/20220227190113.1617498-1-seanga2@gmail.com
2022-03-30 13:03:26 -04:00
Sean Anderson
ac15e789ca clk: Make clk_free return void
Most callers of this function do not check the return value, and it is
unclear what action they should take if it fails. If a function is freeing
multiple clocks, it should not stop just because the first one failed.
Since the callbacks can no longer fail, just convert the return type to
void.

Signed-off-by: Sean Anderson <seanga2@gmail.com>
Link: https://lore.kernel.org/r/20220115222504.617013-8-seanga2@gmail.com
2022-03-30 13:02:55 -04:00
Sean Anderson
3cbdd4cab9 spi: dw: Don't check clk_free
This function always succeeds, so don't check its return value.

Signed-off-by: Sean Anderson <seanga2@gmail.com>
Link: https://lore.kernel.org/r/20220115222504.617013-7-seanga2@gmail.com
2022-03-30 13:02:55 -04:00
Sean Anderson
dfdb227c3d spi: bcm63xx: Don't check clk_free
This function always succeeds, so don't check its return value.

Signed-off-by: Sean Anderson <seanga2@gmail.com>
Link: https://lore.kernel.org/r/20220115222504.617013-6-seanga2@gmail.com
2022-03-30 13:02:55 -04:00
Sean Anderson
ad20358c74 phy: bcm63xx: Don't check clk_free
This function always succeeds, so don't check its return value.

Signed-off-by: Sean Anderson <seanga2@gmail.com>
Link: https://lore.kernel.org/r/20220115222504.617013-5-seanga2@gmail.com
2022-03-30 13:02:55 -04:00
Sean Anderson
b2e0889aba net: bcm63xx: Don't check clk_free
This function always succeeds, so don't check its return value.

Signed-off-by: Sean Anderson <seanga2@gmail.com>
Link: https://lore.kernel.org/r/20220115222504.617013-4-seanga2@gmail.com
2022-03-30 13:02:55 -04:00
Sean Anderson
454af567ed dma: bcm6348: Don't check clk_free
This function always succeeds, so don't check its return value.

Signed-off-by: Sean Anderson <seanga2@gmail.com>
Link: https://lore.kernel.org/r/20220115222504.617013-3-seanga2@gmail.com
2022-03-30 13:02:55 -04:00
Sean Anderson
276d446757 clk: Make rfree return void
When freeing a clock there is not much we can do if there is an error, and
most callers do not actually check the return value. Even e.g. checking to
make sure that clk->id is valid should have been done in request() in the
first place (unless someone is messing with the driver behind our back).
Just return void and don't bother returning an error.

Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/20220115222504.617013-2-seanga2@gmail.com
2022-03-30 13:02:55 -04:00
Michal Simek
fb92cc2c17 pwm: Add driver for cadence TTC
TTC has three modes of operations. Timer, PWM and input counters.

There is already driver for timer under CADENCE_TTC_TIMER which is used for
ZynqMP R5 configuration.
This driver is targeting PWM which is for example configuration which can
be used for fan control.
The driver has been tested on Xilinx Kria SOM platform where fan is
connected to one PL pin. When TTC output is connected via EMIO to PL pin
TTC pwm can be configured and tested for example like this:
pwm config 0 0 10000 1200
pwm enable 0 0
pwm config 0 0 10000 1400
pwm config 0 0 10000 1600

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
Link: https://lore.kernel.org/r/915a662ddb88f7a958ca1f307e8fea59af9d7feb.1634303847.git.michal.simek@xilinx.com
2022-03-30 14:50:47 +02:00
Michal Simek
dcbdd24259 timer: cadence: Add bind function to driver
When DT node has pwm-cells property it shouldn't be bind as timer driver
but as PWM driver. That's why make sure that this property is checked.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/434ef195fbedea9f83672a12d1ace0da16e8832e.1634303847.git.michal.simek@xilinx.com
2022-03-30 14:43:26 +02:00
Ashok Reddy Soma
035d56f238 mmc: zynq_sdhci: Fix SDx_BASECLK configuration
The DLL mode supported SD reference clocks are 50 MHz, 100 MHz and
200 MHz. When user select SD frequency as 200MHz in the design, the
actual frequency is going to come around ~187MHz (<= 200MHz considering
the parent clock and divisor selection). We need to set SDx_BASECLK as
200 in this case, setting 187 will result in tuning failures in mmc.

Set SDx_BASECLK to exact value of 200, 100 or 50 based on the frequency
range.

Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Link: https://lore.kernel.org/r/6c1e5eeeedd2864a0c85e6b409d182031d8c6c1a.1648210268.git.michal.simek@xilinx.com
2022-03-29 09:20:33 +02:00
Michal Simek
cbeba35152 serial: zynq: Change fifo behavior in debug mode
Serial IP has output buffer which status is indicated by two bits. If fifo
if empty or full. Default configuration is that chars are pushed to fifo
till it is full. Time to time it is visible that chars are scambled and
logs are not visible. Not sure what it is exactly happening but all the
time it helps to change driver behavior to write only one char at a time.
That's why enable this mode when debug uart is enabled not to see scrambled
chars in debug by default.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/332b2106d7a8190dd1001b5387f8bd1fba2e061b.1648205405.git.michal.simek@xilinx.com
2022-03-29 09:19:59 +02:00
Michal Simek
f307c688ea firmware: zynqmp: Do not bind PD driver in SPL if disabled
Change if condition to cover SPL flow. SPL needs to have
CONFIG_SPL_POWER_DOMAIN enabled to be able to bind
CONFIG_ZYNQMP_POWER_DOMAIN driver.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/8e1d381013a0ce39d736da166d2b401c4b12d38a.1646064792.git.michal.simek@xilinx.com
2022-03-29 09:12:58 +02:00
Simon Glass
39161e0880 video: Drop formike driver
This is not used. Drop it.

Signed-off-by: Simon Glass <sjg@chromium.org>
2022-03-28 20:29:58 +02:00
Simon Glass
2cbc1c019b video: Convert CONFIG_VIDEO_BCM2835 to Kconfig
This converts the following to Kconfig:
   CONFIG_VIDEO_BCM2835

This is the final ad-hoc CONFIG_VIDEO_... to convert.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Matthias Brugger <mbrugger@suse.com>
2022-03-28 20:28:56 +02:00
Simon Glass
bfd7a1a33c video: mxs: Drop old video code
This is no-longer used and is the last reference to video_hw_init(). Drop
it.

Signed-off-by: Simon Glass <sjg@chromium.org>
2022-03-28 20:18:26 +02:00
Simon Glass
92e3fb8b5e video: Drop FSL DIU driver
This does not use driver model and is more than two years past the
migration date. Drop it.

It can be added back later if needed.

Signed-off-by: Simon Glass <sjg@chromium.org>
2022-03-28 20:18:16 +02:00
Simon Glass
77f46f0607 video: fsl: colibri_vf: Drop FSL DCU driver
This does not use driver model and is more than two years past the
migration date. Drop it.

It can be added back later if needed.

Signed-off-by: Simon Glass <sjg@chromium.org>
2022-03-28 20:18:07 +02:00
Simon Glass
636b8b999c video: Drop da8xx-fb
This is not used in U-Boot anymore. Drop it.

Signed-off-by: Simon Glass <sjg@chromium.org>
2022-03-28 20:17:30 +02:00
Simon Glass
1fa43cad86 video: Drop references to CONFIG_VIDEO et al
Drop the Kconfigs which are not used and all references to them. In
particular, this drops CONFIG_VIDEO to avoid confusion and allow us to
eventually rename CONFIG_DM_VIDEO to CONFIG_VIDEO.

Also drop the prototype for video_get_info_str() which is no-longer used.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Jason Liu <jason.hui.liu@nxp.com>
2022-03-28 20:17:07 +02:00
Simon Glass
fff49e01d8 video: Drop video_fb header
This is not used now. Drop it.

Signed-off-by: Simon Glass <sjg@chromium.org>
2022-03-28 20:16:46 +02:00
Simon Glass
9b39da6e42 video: nexell: Drop unused and invalid code
Unfortunately this driver uses the old video structure to store things.
This is not supported with driver model.

Drop the old code and comment out the other pieces, so the maintainer can
take a look.

Signed-off-by: Simon Glass <sjg@chromium.org>
2022-03-28 20:16:30 +02:00
Simon Glass
814dd92bdc video: Drop cfg_console
The non-driver model video support was removed two years ago. Drop this
driver, which is only used by nokia_rx51.

Signed-off-by: Simon Glass <sjg@chromium.org>
2022-03-28 20:14:24 +02:00
Tom Rini
34d2b7f203 Prepare v2022.04-rc5
-----BEGIN PGP SIGNATURE-----
 
 iQGzBAABCgAdFiEEGjx/cOCPqxcHgJu/FHw5/5Y0tywFAmJBxXQACgkQFHw5/5Y0
 tywKKAv+L+sCmqfJ4Zy2cdzWkGZI3NZMWi8yzUUU37RH5I+3Blht+z6dMslm9gCB
 7/PwS5y7WH3l3wEdeXcw4FUCgNh3D8YyfCcVCsQ0Qxig49xwWz8Jn6t+haOWD6eW
 uXim+gSG+ceWTBrKf3InzXN5fHPIcF66r+k3opwAwIYKpT8p8CgM4ewshBCAsc6t
 6qSLf+A64JNv/y2DTS+sPDY68tnplbyRvrNb6YEazOF6b6SnSE2j+EH8RkIZ+2yT
 cTUhQ2o9JJIKnaG9MTqHB+XVe80oPB7bTWInFo2JxGn98XeS7CTCcnDZhLqWrvHF
 gBfcpEcVE2blVbg/Vo2x4rnU1dop44ch6pE9k5SPFJcPdlzdwFHHgGyfGi9LtD4K
 JAvaIQdz6ZEOQqShpCxcbL/g2/uoRaXFqC7E8IE+WdFMXGBQoZpqaoBMoefnyplk
 xrzqaQye38JgZDX0ku4cm4SMArAfr4sVHcdDlSlzY3y2KQ8Ead25irRvq7GoQ2Ad
 Odo9taQF
 =9g2Y
 -----END PGP SIGNATURE-----

Merge tag 'v2022.04-rc5' into next

Prepare v2022.04-rc5
2022-03-28 12:36:49 -04:00
Han Xu
ed48490f8d mtd: gpmi: fix the bch setting backward compatible issue
Previous u-boot code changed the default bch setting behavior and caused
backward compatible issue. This fix choose the legacy bch geometry back
again as the default option. If the minimum ecc strength that NAND chips
required need to be chosen, it can be enabled by either adding DT flag
"fsl,use-minimum-ecc" or CONFIG_NAND_MXS_USE_MINIMUM_ECC in configs. The
unused flag "fsl,legacy-bch-geometry" get removed.

Fixes: 51cdf83eea (mtd: gpmi: provide the option to use legacy bch geometry)
Fixes: 616f03daba (mtd: gpmi: change the BCH layout setting for large oob NAND)
Tested-by: Tim Harvey <tharvey@gateworks.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Han Xu <han.xu@nxp.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
2022-03-28 08:22:17 -04:00
Pali Rohár
d66b0f5dd7 Fix URLs to old freescale git repos
Freescale git repos are now on source.codeaurora.org.

Signed-off-by: Pali Rohár <pali@kernel.org>
2022-03-28 08:22:17 -04:00
Philip Oberfichtner
c537a36839 bootcount: Add pmic pfuze100 bootcount driver
Use the MEMA - MEMD registers on the PFUZE100 as bootcount
registers.

Based on work from Heiko Schocher <hs@denx.de>.
Signed-off-by: Philip Oberfichtner <pro@denx.de>
2022-03-25 16:42:40 -04:00
Simon Glass
88ca8e2695 disk: Add an option for partitions in SPL
In some cases we do not want to enable partition support in SPL. Add an
option to allow this.

Signed-off-by: Simon Glass <sjg@chromium.org>
2022-03-25 16:42:40 -04:00
Billy Tsai
73ee1f261e pinctrl: Add the pinctrl setting for PWM.
This patchs add the signal description array for PWM pinctrl settings.

Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
2022-03-25 13:35:50 -04:00
Billy Tsai
fae101d6e8 pwm: Add Aspeed ast2600 PWM support
This patch add the support of PWM controller which can be found at aspeed
ast2600 soc. The pwm supoorts up to 16 channels and it's part function
of multi-function device "pwm-tach controller".

Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
2022-03-25 13:35:50 -04:00
Pali Rohár
d7b904092d pci: Add defines for normal and subtractive PCI bridges
Add following two new PCI class codes defines into pci_ids.h include file:

  PCI_CLASS_BRIDGE_PCI_NORMAL
  PCI_CLASS_BRIDGE_PCI_SUBTRACTIVE

And use these defines in all U-Boot code for describing PCI class codes for
normal and subtractive PCI bridges.

Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
2022-03-25 13:35:50 -04:00
Tom Rini
3e2ea3278e Convert CONFIG_LCD_INFO et al to Kconfig
This converts the following to Kconfig:
   CONFIG_LCD_INFO
   CONFIG_LCD_LOGO
   CONFIG_LCD_INFO_BELOW_LOGO
   CONFIG_LCD_IN_PSRAM

Cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
2022-03-25 12:01:15 +00:00
Tom Rini
286c4531ad Convert CONFIG_ATMEL_LCD et al to Kconfig
This converts the following to Kconfig:
   CONFIG_ATMEL_LCD
   CONFIG_ATMEL_LCD_BGR555
   CONFIG_ATMEL_LCD_RGB565
   CONFIG_GURNARD_SPLASH

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-03-25 12:01:15 +00:00
Tom Rini
cc386f161c Convert CONFIG_MII_INIT to Kconfig
This converts the following to Kconfig:
   CONFIG_MII_INIT

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-03-25 12:01:15 +00:00
Tom Rini
16199a8b96 Convert CONFIG_PHY_RESET_DELAY to Kconfig
This converts the following to Kconfig:
   CONFIG_PHY_RESET_DELAY

Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2022-03-25 12:01:15 +00:00
Tom Rini
6329dda175 Convert CONFIG_LPC32XX_ETH to Kconfig
This converts the following to Kconfig:
   CONFIG_LPC32XX_ETH

Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2022-03-25 12:01:15 +00:00
Tom Rini
03d14ccdf6 Convert CONFIG_RMII to Kconfig
This converts the following to Kconfig:
   CONFIG_RMII

Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2022-03-25 12:01:15 +00:00
Michael Opdenacker
fc1383ae2b bootcount: clarify documentation
- Grammar fixes
- Clarify explanations

Signed-off-by: Michael Opdenacker <michael.opdenacker@bootlin.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
2022-03-23 07:27:38 +01:00
Nikita Yushchenko
6db539f983 i2c: fix always-true condition in i2c_probe_chip()
Per dm_i2c_ops.probe_chip documentation, i2c_probe_chip() shall fallback
to default probe method when .probe_chip() returns -ENOSYS.

Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
2022-03-23 07:27:37 +01:00
Adrian Fiergolski
532a5b297c misc: atsha204a: fix i2c address readout from DTS
This patch replaces use fdtdec_get_addr with simpler dev_read_addr().
fdtdec_get_addr doesn't work properly on ZynqMP-based (64bit) system. Although
not confirmed, it could be related to the fact, that quoting the documentation,
"This variant hard-codes the number of cells used to represent the address and
size based on sizeof(fdt_addr_t) and sizeof(fdt_size_t)".

Signed-off-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
2022-03-23 07:27:37 +01:00
Adrian Fiergolski
e4662716fb misc: atsha204a: add delay after sending the message
Once request is sent, and before receiving a response, the delay is required.
This patch fixes missing delay for before first response try.

Signed-off-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
2022-03-23 07:27:37 +01:00
Adrian Fiergolski
75967a24f9 misc: atsha204a: return timeout from wakeup function
If the maximum number of wake-up attempts is exceeded, return -ETIMEDOUT.

Signed-off-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
2022-03-23 07:27:37 +01:00
Tom Rini
a958c58571 binman FIT improvements
various minor sandbox improvements
 -----BEGIN PGP SIGNATURE-----
 
 iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmI1URkRHHNqZ0BjaHJv
 bWl1bS5vcmcACgkQfxc6PpAIreYglAf/eM5MtohjWDBQUyvPiQTIV0iS5Zu7NV7Z
 1qkrv4OuwZ+U3djtusP7VIUnmdnQlwbF1fFZzo+JUmtYg59K6ZvgI/S+oJzr17/D
 bMh+8FpDggEjJhzwSM5fdImfE1PLp161zUxTWMH25VmB+yxQMGWqZBQls+0GADN5
 jT4dGwTn098a2HLvdAqkNwafY0Q1cUQeYg8z2J3gdDdZos2PdQV3TqjbrAS6Pr+Z
 jAZV+TfTkU2rk6S7B34Ojzx2dF8e80sRK/o/2/+60kt+dUO+nfS/evOb1kqfj8dx
 ULNXEBjS1aMy7Z6TCg/E3uEZLM5xyaTZKTwiNeKMthmOK8ZQ3boRuA==
 =9FkF
 -----END PGP SIGNATURE-----

Merge tag 'dm-pull-18mar22' of https://source.denx.de/u-boot/custodians/u-boot-dm into next

binman FIT improvements
various minor sandbox improvements
2022-03-19 09:09:58 -04:00
Simon Glass
7c19e4cbfe sandbox: Slow down the LCD sync rate
There is seldom a need to refresh at 100Hz and it uses a lot of CPU.
Reduce the rate to 10Hz which seems to be adequate.

Signed-off-by: Simon Glass <sjg@chromium.org>
2022-03-18 19:24:24 -06:00
Simon Glass
7aa9dbd0ab sandbox: Open host file for read-only access if needed
Some files cannot be written but read-only access is still useful for
tests. Add a fallback to read-only access when needed.

This is useful in CI when opening a large data file provided by docker,
where read/write access would result in copying the file, thus needing
a lot of extra disk space.

Signed-off-by: Simon Glass <sjg@chromium.org>
2022-03-18 19:24:24 -06:00
Tom Rini
08f1d58aff net: fec_mxc: Drop CONFIG_FEC_XCV_TYPE
With all boards now using DM_ETH we determine the value for
CONFIG_FEC_XCV_TYPE at run time, except in the case of the default
fall-back.  Set the fallback directly now.

Cc: Fabio Estevam <festevam@gmail.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
2022-03-18 12:48:17 -04:00
Tom Rini
b07fb55747 net: fec_mxc: Remove non-DM_ETH code
Now that all boards have been converted, remove the non-DM_ETH code.

Cc: Fabio Estevam <festevam@gmail.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
2022-03-18 12:48:17 -04:00
Johan Jonker
861682b596 rockchip: ram: sdram_rk3x88: replace comma by semicolon
A comma at the end of a line gives sometimes strange
effects in combination with some code formatters,
so replace a comma by a semicolon in the sdram_rk3188.c
and sdram_rk3288.c files.

Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2022-03-18 18:12:03 +08:00
Giulio Benetti
9acae54800 rockchip: saradc: remove double semi-colon
Remove double semi-colon that has been forgotten while adding the
driver. This is only a style fix since it doesn't change the
functionality of the driver.

Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2022-03-18 18:12:03 +08:00
Tom Rini
297e6eb8dc Xilinx changes for v2022.07-rc1
microblaze:
 - Add support for reserved memory
 
 xilinx:
 - Update FRU code with MAC reading
 
 zynqmp:
 - Remove double AMS setting
 - DT updates (mostly for SOMs)
 - Add support for zcu106 rev 1.0
 
 zynq:
 - Update nand binding
 
 nand:
 - Aligned zynq_nand to upstream DT binding
 
 net:
 - Add support for ethernet-phy-id
 
 mmc:
 - Workaround CD in zynq_sdhci driver also for ZynqMP
 - Add support for dynamic/run-time SD config for SOMs
 
 gpio:
 - Add driver for slg7xl45106
 
 firmware:
 - Add support for dynamic SD config
 
 power-domain:
 - Update zynqmp driver with the latest firmware
 
 video:
 - Add skeleton driver for DP and DPDMA
 
 i2c:
 - Fix i2c to work with QEMU
 
 pinctrl:
 - Add driver for zynqmp pinctrl driver
 -----BEGIN PGP SIGNATURE-----
 
 iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYjIBkgAKCRDKSWXLKUoM
 IYUwAKCYRBxb59BFq4MRvTbNcRZ7H4oGIQCfVUl3x9KZ7nFZaYAaBXFBxwna+PE=
 =irCR
 -----END PGP SIGNATURE-----

Merge tag 'xilinx-for-v2022.07-rc1' of https://source.denx.de/u-boot/custodians/u-boot-microblaze into next

Xilinx changes for v2022.07-rc1

microblaze:
- Add support for reserved memory

xilinx:
- Update FRU code with MAC reading

zynqmp:
- Remove double AMS setting
- DT updates (mostly for SOMs)
- Add support for zcu106 rev 1.0

zynq:
- Update nand binding

nand:
- Aligned zynq_nand to upstream DT binding

net:
- Add support for ethernet-phy-id

mmc:
- Workaround CD in zynq_sdhci driver also for ZynqMP
- Add support for dynamic/run-time SD config for SOMs

gpio:
- Add driver for slg7xl45106

firmware:
- Add support for dynamic SD config

power-domain:
- Update zynqmp driver with the latest firmware

video:
- Add skeleton driver for DP and DPDMA

i2c:
- Fix i2c to work with QEMU

pinctrl:
- Add driver for zynqmp pinctrl driver
2022-03-16 12:52:02 -04:00
Tom Rini
e7fb67df31 Merge https://source.denx.de/u-boot/custodians/u-boot-mmc
- Rockchip, i.MX and xenon_sdhci updates
2022-03-16 08:13:16 -04:00
Tom Rini
469c1bc688 Merge https://source.denx.de/u-boot/custodians/u-boot-riscv
- k210 updates
2022-03-16 08:11:53 -04:00