Commit graph

3094 commits

Author SHA1 Message Date
Alessandro Rubini
f7aa59b29a arm nomadik: allow Nand and OneNand to coexists
The evaluation kit has both Nand and OneNand, both drivers are there
and the two configurations only select a different default for the
jffs partition. This adds the OneNand driver and cleans up storage.

Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
2009-07-06 21:53:06 +02:00
Alessandro Rubini
ee1363f2da arm nomadik: rename board to nhk8815
This is an error in my side in the initial submission: nobody
calls it ""nmdk8815", it's "nomadik hardware kit", nhk8815, instead.

Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
2009-07-06 21:53:00 +02:00
Stefano Babic
040f8f63e9 xscale: add support for the polaris board
The Polaris board is based on the TrizepsIV module of
Keith & Koep (http://www.keith-koep.com).

Signed-off-by: Stefano Babic <sbabic@denx.de>
2009-07-06 21:52:58 +02:00
Stefano Babic
88bd975013 xscale: fix USB initialization for Trizepsiv module
Due to change in the usb_board_init() prototype, the USB for
the TrizepsIV was not correctly initialized.
Removed dummy print from usb_board_stop().

Signed-off-by: Stefano Babic <sbabic@denx.de>
2009-07-06 21:52:55 +02:00
Daniel Gorsulowski
33b1d3f43a at91: Add esd gmbh MEESC board support
This patch adds support for esd gmbh MEESC board.
The MEESC is based on an Atmel AT91SAM9263 SoC.

Signed-off-by: Daniel Gorsulowski <Daniel.Gorsulowski@esd.eu>
2009-07-06 21:52:50 +02:00
Magnus Lilja
8449f287f5 MX31: Add basic support for Freescale i.MX31 PDK board.
Add support for Freescale's i.MX31 PDK board (a.k.a. 3 stack board).

This patch assumes that some other program performs the actual
NAND boot.

Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Acked-by: Fabio Estevam <fabioestevam@yahoo.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-07-06 21:52:38 +02:00
Matthias Ludwig
9c8c706c92 OMAP3EVM: fix typo. replace CS6 by CS5, no functionality change
Signed-off-by: Matthias Ludwig <mludwig@ultratronik.de>
2009-07-06 21:52:12 +02:00
Sedji Gaouaou
0aafde1dc7 at91sam9260/9263: add back up for the rst(reset controller).
On the boards at91sam9260ek, at91sam9263ek and afed9260, the rstc register was
set to 0 after being set to 500 ms for the PHY reset.
Do backup the old reset length and restore it after the MACB initialisation.

Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
Signed-off-by: Stelian Pop <stelian@popies.net>
2009-07-06 21:50:09 +02:00
Kumar Gala
afb0b1315c fsl: Fix compiler warnings from gcc-4.4 in sys_eeprom code
sys_eeprom.c: In function 'do_mac':
sys_eeprom.c:323: warning: dereferencing type-punned pointer will break strict-aliasing rules
sys_eeprom.c: In function 'mac_read_from_eeprom':
sys_eeprom.c:395: warning: dereferencing type-punned pointer will break strict-aliasing rules

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-07-03 12:46:47 -05:00
Peter Tyser
9adda5459c 83xx: Replace CONFIG_ECC_INIT_VIA_DDRC references
Update 83xx architecture's CONFIG_ECC_INIT_VIA_DDRC references to
CONFIG_ECC_INIT_VIA_DDRCONTROLLER, which other Freescale architectures
use

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-07-02 11:15:49 -05:00
Peter Tyser
5da6f806b4 86xx: XPedite5170 board support
Initial support for Extreme Engineering Solutions XPedite5170 -
a MPC8640-based 3U VPX single board computer with a PMC/XMC
site.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-07-01 23:25:48 -05:00
Peter Tyser
0d595f76bc fsl_dma: Break out common memory initialization function
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-07-01 23:12:01 -05:00
Peter Tyser
79f4333ceb 8xxx: Move dma_init() call to common code
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-07-01 23:12:00 -05:00
Peter Tyser
7892f619d4 8xxx: Rename dma_xfer() to dmacpy()
Also update dmacpy()'s argument order to match memcpy's and use
phys_addr_t/phy_size_t for address/size arguments

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-07-01 23:07:47 -05:00
Roy Zang
29c3518246 85xx: Add pci e1000 Ethernet support for P2020 board
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-06-30 08:26:34 -05:00
Jean-Christophe PLAGNIOL-VILLARD
576afd4fae integrator: merge integratorap and integratorcp
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Peter Pearse <peter.pearse@arm.com>
2009-06-23 00:10:04 +02:00
Jean-Christophe PLAGNIOL-VILLARD
46937b2742 integratorap/cp: use cfi driver
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Peter Pearse <peter.pearse@arm.com>
2009-06-23 00:10:04 +02:00
Jean-Christophe PLAGNIOL-VILLARD
de7a01abd8 integratorap/cp/versatile: remove non used functions
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Peter Pearse <peter.pearse@arm.com>
2009-06-23 00:10:04 +02:00
Jean-Christophe PLAGNIOL-VILLARD
f54851a6e3 integratorcp: split timer support
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Peter Pearse <peter.pearse@arm.com>
2009-06-23 00:10:03 +02:00
Jean-Christophe PLAGNIOL-VILLARD
2bcef0723e integratorap: split timer support
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Peter Pearse <peter.pearse@arm.com>
2009-06-23 00:10:03 +02:00
Jean-Christophe PLAGNIOL-VILLARD
86baa085c5 integratorap: split pci support
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Peter Pearse <peter.pearse@arm.com>
2009-06-23 00:10:03 +02:00
Jean-Christophe PLAGNIOL-VILLARD
8096c51fd4 at91: unify nor boot support
the lowlevel init sequence is the same so unify it

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-06-21 16:18:12 +02:00
Jean-Christophe PLAGNIOL-VILLARD
1b3b7c640d at91sam9263ek: add nor flash support
this will allow you to store use it for the env and to boot directly U-Boot from

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-06-21 16:18:11 +02:00
Ilko Iliev
3294923297 at91: add support for the PM9261 board of Ronetix GmbH
The PM9261 board is based on the AT91SAM9261-EK board.

Here is the page on Ronetix website:
http://www.ronetix.at/starter_kit_9261.html

Signed-off-by: Ilko Iliev <iliev@ronetix.at>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-06-21 16:18:11 +02:00
Jean-Christophe PLAGNIOL-VILLARD
01550a2b65 pm9263: use macro instead of hardcode value for the lowlevel_init
optimize a few the RAM init

Signed-off-by: Ilko Iliev <iliev@ronetix.at>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-06-21 16:18:11 +02:00
Jean-Christophe PLAGNIOL-VILLARD
7a11c7f974 pm9263: lowlevel init update
move PSRAM init to pm9263.c
this will allow us after to make the nor lowlevel_init generic

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-06-21 16:18:11 +02:00
Mike Frysinger
9ae55ccf60 Blackfin: enable -O2 in lib_generic/ for ADI/Bluetechnix boards
Building the compression code in lib_generic/ with -O2 rather than -Os
gives a nice speed boost without too much code size increase.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-15 13:30:19 -04:00
Wolfgang Denk
c9005a72fe Merge branch 'master' of git://git.denx.de/u-boot-net 2009-06-15 11:15:54 +02:00
Remy Bohmer
60f61e6d76 Convert DM9000 driver for CONFIG_NET_MULTI
All drivers need to be converted to CONFIG_NET_MULTI.
This patch converts the dm9000 driver.

Signed-off-by: Thomas Smits <ts.smits@gmail.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-06-15 00:13:55 -07:00
Ben Warren
8453587ef9 Switched davinci_emac Ethernet driver to use newer API
Added CONFIG_NET_MULTI to all Davinci boards
Removed all calls to Davinci network driver from board code
Added cpu_eth_init() to cpu/arm926ejs/cpu.c

Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-06-15 00:13:54 -07:00
Mike Frysinger
9ff67e5e4c Blackfin: unify u-boot linker scripts
All the Blackfin linker scripts were duplicated across the board dirs with
no difference save from the semi-often used ENV_IS_EMBEDDED option.  So
unify all of them in the lib_blackfin/ dir and for the few boards that
need to embedded the environment directly, add a LDS_BOARD_TEXT define for
them to customize via their board config file.  This is much simpler than
forcing them to duplicate the rest of the linker script.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-14 20:01:14 -04:00
Hoan Hoang
0f52b560f1 Blackfin: ibf-dsp561: new board port
Signed-off-by: Hoan Hoang <hnhoan@i-syst.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-14 20:01:11 -04:00
Mike Frysinger
3088189a15 Blackfin: blackstamp: new board port
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-14 20:01:11 -04:00
Mike Frysinger
59ac972970 Blackfin: bf537-srv1: new board port
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-14 20:01:10 -04:00
Mike Frysinger
d7fdc1410b Blackfin: bf537-minotaur: new board port
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-14 20:01:09 -04:00
Mike Frysinger
cb4b5e874f Blackfin: bf537-pnav: new board port
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-14 20:01:08 -04:00
Mike Frysinger
59e4be945b Blackfin: cm-bf527: new board port
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-14 20:01:07 -04:00
Mike Frysinger
8b219cf07c Blackfin: cm-bf548: new board port
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-14 20:01:07 -04:00
Mike Frysinger
9417d9a213 Blackfin: tcm-bf537: new board port
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-14 20:01:06 -04:00
Mike Frysinger
e548321af0 Blackfin: cm-bf561: new board port
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-14 20:01:06 -04:00
Mike Frysinger
8a9bab08a6 Blackfin: cm-bf537e: new board port
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-14 20:01:05 -04:00
Mike Frysinger
e82d8a1f02 Blackfin: cm-bf533: new board port
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-14 20:01:04 -04:00
Grzegorz Bernacki
12304871bc digsy MTC: Add 'mtc' command.
New command allows to:
     o check FW version
     o set LED status
     o set digital output status
     o get digital input status

Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
2009-06-14 23:04:37 +02:00
Grzegorz Bernacki
f1f66edfc7 digsy MTC: Add SPI support.
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
2009-06-14 23:03:57 +02:00
Peter Tyser
388517e4b7 xes: Update Freescale clock code to work with 86xx processors
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-06-12 17:23:47 -05:00
Peter Tyser
25623937bb xes: Update Freescale DDR code to work with 86xx processors
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-06-12 17:23:45 -05:00
Peter Tyser
bef3013908 xes: Update Freescale PCI code to work with 86xx processors
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-06-12 17:23:43 -05:00
Haiying Wang
9a6110897f fsl: Update the number of ethxaddr in reading system eeprom
We support up to 8 mac addresses in system eeprom, so we define the macro
MAX_NUM_PORTS to limit the mac_count to 8, and update the number of ethxaddr
according to mac_count.

Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-06-12 17:17:01 -05:00
Haiying Wang
f82107f637 85xx: Add RMII support for MPC8569MDS
This patch supports UCC working at RMII mode on PIB board, fixup fdt blob to
support rmii in kernel. It also changes the name of enable_mpc8569mds_qe_mdio to
enalbe_mpc8569mds_qe_uec which is  more accurate.

Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-06-12 17:17:01 -05:00
Haiying Wang
750098d33b 85xx: Add UEC3 and UEC4 support for MPC8569MDS
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-06-12 17:17:00 -05:00
Srikanth Srinivasan
feb7838f97 85xx: Add P2020DS support
The patch adds support for P2020DS reference platform.
DDR3 interface uses hard-coded initialization rather than SPD
for now and was tested at 667Mhz. Some PIXIS register
definitions and associated code sections need to be fixed.
TSEC1/2/3, NOR flash, MAC/SYS ID EEPROM, PCIE1/2/3 are all
tested under u-boot.

Signed-off-by: Srikanth Srinivasan <srikanth.srinivasan@freescale.com>
Signed-off-by: Travis Wheatley <Travis.Wheatley@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-06-12 17:16:25 -05:00
Stefan Roese
229549a56d mpc512x: MPC5121ADS: Add NAND support
This patch adds NAND support to the MPC5121ADS board. Please
note that the image size increased since NAND support didn't
fit in the current image size (256k).

Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
2009-06-12 20:47:19 +02:00
Stefan Roese
e53b507cee mpc512x: Add esd gmbh mecp5123 board support
MECP5123 is a MPC5121E based module by esd gmbh.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
2009-06-12 20:47:19 +02:00
Stefan Roese
58f10460b0 74xx_7xx: CPCI750: Add CPCI adapter/target support
The CPCI750 can be built as CPCI host or adapter/target board. This patch
adds support for runtime detection of those variants.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
2009-06-12 20:47:18 +02:00
Stefan Roese
ae7a2739d7 74xx_7xx: CPCI750: Enable access to PCI function > 0
The Marvell bridge 64360 supports serveral PCI functions, not only 0. This
patch enables access to those functions.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
2009-06-12 20:47:18 +02:00
Stefan Roese
e5b563e9ec 74xx_7xx: CPCI750: Minor coding style cleanup of cpci750.c
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
2009-06-12 20:47:18 +02:00
Stefan Roese
0e5ef07d0d 74xx_7xx: CPCI750: Add loadpci command
This command is used to load/boot an OS-image which is transferred from
the CPCI host to the CPCI target/adapter.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
2009-06-12 20:47:18 +02:00
Peter Tyser
0f89860494 83xx: Replace CONFIG_MPC83XX with CONFIG_MPC83xx
Use the standard lowercase "xx" capitalization that other Freescale
architectures use for CPU defines to prevent confusion and errors

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-06-12 20:47:17 +02:00
Wolfgang Denk
52568c3654 MPC512x: add support for ARIA board
ARIA is a MPC5121E based COM Express module by Dave/DENX.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: John Rigby <jcrigby@gmail.com>
2009-06-12 20:47:16 +02:00
Wolfgang Denk
843efb1192 MPC512x: use I/O accessors instead of pointer accesses
This commit changes the MPC512x code to use I/O accessor calls (i.e.
out_*() and in_*()) instead of using deprecated pointer accesses.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: John Rigby <jcrigby@gmail.com>
2009-06-12 20:47:16 +02:00
Wolfgang Denk
19dc7e1792 MPC512x: add more hardware description to immap_512x.h
- add GPIO module description
- add Address Latch Timing Register description
- add IO Control Memory Map
- add FEC Memory Map

Also change board/freescale/mpc5121ads/mpc5121ads.c and
cpu/mpc512x/iopin.c as needed.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: John Rigby <jcrigby@gmail.com>
2009-06-12 20:47:16 +02:00
Wolfgang Denk
72601d04fd Rename ads5121 board into mpc5121ads
We rename the board so we use a consistent name in U-Boot and in
Linux.  Also, we use this opportunity to move the board into the
Freecale vendor directory.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: John Rigby <jcrigby@gmail.com>
2009-06-12 20:47:16 +02:00
Wolfgang Denk
de26ef99bd mpc512x: Move common files to share them by several boards
We will soon see several new MPC521x based boards added.  This patch
moves files that are not board specific to a common directory so they
can be shared by all such ports.  It also splits off common IDE code
into a new file, cpu/mpc512x/ide.c .

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: John Rigby <jcrigby@gmail.com>
2009-06-12 20:47:16 +02:00
Wolfgang Denk
a89c33db96 General help message cleanup
Many of the help messages were not really helpful; for example, many
commands that take no arguments would not print a correct synopsis
line, but "No additional help available." which is not exactly wrong,
but not helpful either.

Commit ``Make "usage" messages more helpful.'' changed this
partially. But it also became clear that lots of "Usage" and "Help"
messages (fields "usage" and "help" in struct cmd_tbl_s respective)
were actually redundant.

This patch cleans this up - for example:

Before:
	=> help dtt
	dtt - Digital Thermometer and Thermostat

	Usage:
	dtt         - Read temperature from digital thermometer and thermostat.

After:
	=> help dtt
	dtt - Read temperature from Digital Thermometer and Thermostat

	Usage:
	dtt

Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-06-12 20:47:16 +02:00
Tom Rix
a30f519bd0 ZOOM2 detect the version of the zoom2 board at runtime.
There are currently 3 versions of the zoom2 board.
The production board, that is currently being released.
The beta board, similar in form to the production board but not released.
The alpha board, a set of PCBs with a very limited circulation.

GPIO 94 is used to determine the version of the board. If GPIO 94 is clear,
the board is a production board, otherwise it is a beta board.

The alpha board will likely be mistaken for a beta board.  An alpha board
was unavailible for testing.

This has been tested on the beta and production boards.

Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-06-12 20:45:47 +02:00
Tom Rix
718763c474 Beagle Convert the board version detection to use the OMAP3 GPIO interface.
There is no new functionality in the change.

This change is a conversion from the using raw register access to using
the OMAP3 GPIO API described in doc/README.omap3.

Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Acked-by: Dirk Behme <dirk.behme@googlemail.com>
2009-06-12 20:45:47 +02:00
Jean-Christophe PLAGNIOL-VILLARD
b2403589b4 at91: move cpu info print to cpu
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-06-12 20:45:46 +02:00
Dirk Behme
9d4fc99dbd OMAP3: Fix CKE1 MUX setting to allow self-refresh
The Beagle rev Cx and Overo boards are using both SDRC CSes. The MUX
setting is needed for the second CS clock signal to allow the 2 RAM
parts to be put in self-refresh correctly. This also works on rev B
Beagle boards with 128M of RAM.

From: Steve Sakoman <steve@sakoman.com>
From: Jean Pihet <jpihet@mvista.com>
Signed-off-by: Jean Pihet <jpihet@mvista.com>
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
2009-06-12 20:39:53 +02:00
Tom Rix
83ae698ff2 ZOOM2 Add led support.
This patch controls the large LED on the top left of the zoom2.

Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
2009-06-12 20:39:53 +02:00
Tom Rix
660888b7fb ZOOM2 Add serial support.
Zoom2 serial is in general supplied by one of the 4 UARTS on the debug board.
The default serial is from the USB connector on left side of the debug board.
The USB connector will produce 2 of the 4 UARTS.  On your host pick the first
enumeration.

The details of the setting of the serial gpmc setup are not available.
The values were provided by another party.

The serial port set up is the same with Zoom1.
Baud rate 115200, 8 bit data, no parity, 1 stop bit, no flow.

The kernel bootargs are
console=ttyS3,115200n8

Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
2009-06-12 20:39:53 +02:00
Jean-Christophe PLAGNIOL-VILLARD
10a451cd57 arm: unify linker script
all arm boards except a few use the same cpu linker script
so move it to cpu/$(CPU)

that could be overwrite in following order
SOC
BOARD
via the corresponding config.mk

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-06-12 20:39:52 +02:00
Wolfgang Denk
4681e673a5 TQM834x: add FDT support
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-06-12 20:39:52 +02:00
David Brownell
28b00324be dm355 evm support
Initial U-Boot support for the DaVinci DM355 EVM.  This is a board
from Spectrum Digital.  Board docs include schematic and firmware
for its microcontroller:

  http://c6000.spectrumdigital.com/evmdm355/revd/

Most of the DM355 chip is fully documented by TI, the most notable
exception being the MPEG/JPEG coprocessor (programmable using codecs
available at no cost from TI), which is omitted from its DM335 sibling:

  http://focus.ti.com/docs/prod/folders/print/tms320dm355.html

This version can boot from the on-board DM9000 Ethernet chip, after
being loaded (from NAND, MMC/SD, or UART).  In the near future, NAND
and USB support could be added ... NAND support is being held back
until the support for the 4-bit ECC hardware is ready.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2009-06-12 20:39:51 +02:00
Tom Rix
de193e8e36 ZOOM2 Add support for debug board detection.
The logicpd web site is a good source for general information on this board.
Please start looking here if the below links are broken.
http://www.logicpd.com

This is a pdf of the product
http://www.logicpd.com/sites/default/files/1012659A_Zoom_OMAP34x-II_MDP_Brief.pdf

This is a pdf of the product quick start guide.
The debug board is described here.
http://support.logicpd.com/downloads/1165/

This is a wiki showing the debug board in use
https://omapzoom.org/gf/project/omapzoom/wiki/?pagename=GettingStartedWithZoomII_AKA_OMAP34XII_MDP

The zoom2 has an auxillary board that contains the serial, net, jtag and
battery simulator.  This change supports a runtime check if the debug board is
connected.

Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
2009-06-12 20:39:50 +02:00
Tom Rix
376aee78dd ZOOM2 Add initial support for Zoom2
Zoom2 is a new board from Texas Instruments and LogicPD

The logicpd web site is a good source for general information on this board.
Please start looking here if the below links are broken.
http://www.logicpd.com

This is a pdf of the product
http://www.logicpd.com/sites/default/files/1012659A_Zoom_OMAP34x-II_MDP_Brief.pdf
This is the product description web page
http://www.logicpd.com/products/development-kits/texas-instruments-zoom%E2%84%A2-omap34x-ii-mdp

This patch provides a zoom2 base target by copying zoom1 and by making some
obvious changes.

To configure, run
make omap3_zoom2_config

Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
2009-06-12 20:39:50 +02:00
Sandeep Paulraj
53925acf1b ARM DaVinci:Consolidate common u-boot.lds
The u-boot.lds is common for all DaVinci boards. The patch removes
multiple instances and moves the u-boot.lds to /cpu/arm926ejs/davinci
folder. This addresses one of the comments i received while submitting
patches for DM3xx

Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2009-06-12 20:39:49 +02:00
Tom Rix
68a531fd46 OMAP Consolidate common u-boot.lds to cpu layer.
The u-boot.lds file is common for all omap boards.
Move a cleaned up version to the cpu layer and add makefile logic to use it.

Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
2009-06-12 20:39:49 +02:00
David Brownell
7a4f511b59 davinci: display correct clock info
Move the clock-rate dumping code into the cpu/.../davinci area
where it should have been, enabled by CONFIG_DISPLAY_CPUINFO,
updating the format and showing the DSP clock (where relevant).

Switch boards to use the cpuinfo() hook for this stuff.

Remove a few now-obsolete PLL #defines.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2009-06-12 20:39:49 +02:00
Jean-Christophe PLAGNIOL-VILLARD
b54384e3ba arm: timer and interrupt init rework
actually the timer init use the interrupt_init as init callback
which make the interrupt and timer implementation difficult to follow

so now rename it as int timer_init(void) and use interrupt_init for interrupt

btw also remane the corresponding file to the functionnality implemented

as ixp arch implement two timer - one based on interrupt - so all the timer
related code is moved to timer.c

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-06-12 20:39:48 +02:00
David Brownell
7b7808ae6d davinci: move psc support board-->cpu
Move DaVinci PSC support from board/* to cpu/* where it belongs.
The PSC module manages clocks and resets for all DaVinci-family
SoCs, and isn't at all board-specific.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2009-06-12 20:39:47 +02:00
David Brownell
641e0925e4 DaVinci Ethernet cleanup
Chips without the EMAC controller won't need the utilities
it uses to read an Ethernet address from EEPROM; so don't
include them needlessly.

Use is_valid_ether() to validate the address from EEPROM.
All-zero addresses aren't the only invalid addresses.
A fully erased EEPROM returns all-ones, also invalid...

Switch those Ethernet utilities to use "%pM" for printing
MAC addresses; and not say ROM when they mean EEPROM.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
2009-06-12 20:39:47 +02:00
Stefan Roese
d873133f2b ppc4xx: Add Sequoia RAM-booting target
This patch adds another build target for the AMCC Sequoia PPC440EPx
eval board. This RAM-booting version is targeted for boards without
NOR FLASH (NAND booting) which need a possibility to initially
program their NAND FLASH. Using a JTAG debugger (e.g. BDI2000/3000)
configured to setup the SDRAM, this debugger can load this RAM-
booting image to the target address in SDRAM (in this case 0x1000000)
and start it there. Then U-Boot's standard NAND commands can be
used to program the NAND FLASH (e.g. "nand write ...").

Here the commands to load and start this image from the BDI2000:

440EPX>reset halt
440EPX>load 0x1000000 /tftpboot/sequoia/u-boot.bin
440EPX>go 0x1000000

Please note that this image automatically scans for an already
initialized SDRAM TLB (detected by EPN=0). This TLB will not be
cleared. This TLB doesn't need to be TLB #0, this RAM-booting
version will detect it and preserve it. So booting via BDI2000
will work and booting with a complete different TLB init via
U-Boot works as well.

Signed-off-by: Stefan Roese <sr@denx.de>
2009-06-12 20:39:47 +02:00
Matthias Fuchs
70be6c2d40 4xx: Add support for DP405 hardware variants
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
2009-06-12 20:39:47 +02:00
Matthias Fuchs
de47a34d4d 4xx: Remove binary cpld bitstream from DP405 board
This patch removes the cpld binary bitstream that is
used by esd's cpld command on DP405 boards.

Because u-boot with an external cpld bitstream may not
take more space in flash than before the u-boot binary is
shrinked a little bit. Some unused featues have been
removed therefore.

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
2009-06-12 20:39:47 +02:00
Matthias Fuchs
700d553fd3 4xx: Remove binary cpld bitstream from VOM405 board
This patch removes the cpld binary bitstream that is
used by esd's cpld command on VOM405 boards.

Because u-boot with an external cpld bitstream may not
take more space in flash than before the u-boot binary is
shrinked a little bit.

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
2009-06-12 20:39:46 +02:00
Matthias Fuchs
0bb1063036 4xx: Remove binary cpld bitstream from PMC405 board
This patch removes the cpld binary bitstream that is
used by esd's cpld command on PMC405 boards.

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
2009-06-12 20:39:46 +02:00
Matthias Fuchs
7cc635fb35 4xx: Remove binary cpld bitstream from CMS700 board
This patch removes the cpld binary bitstream that is
used by esd's cpld command on CMS700 boards.

Because u-boot with an external cpld bitstream may not
take more space in flash than before the u-boot binary is
shrinked a little bit. Some unused featues have been
removed therefore.

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
2009-06-12 20:39:46 +02:00
Matthias Fuchs
c1b2f79788 esd/common: extend cpld command with address parameter
This patch adds support for an address parameter to esd's
cpld command. This is in preparation to remove compiled-in
binary cpld (xsvf) bitstreams.

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
2009-06-12 20:39:46 +02:00
Peter Tyser
0f89c54be9 i2c: Update references to individual i2c commands
The individual i2c commands imd, imm, inm, imw, icrc32, iprobe, iloop,
and isdram are no longer available so all references to them have been
updated to the new form of "i2c <cmd>".

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2009-06-12 20:39:46 +02:00
Peter Tyser
8229e9c04f cm5200: Make function test command names more unique
Add "_test" to cm5200's function test command names to prevent
overlap with common, global function names.  Originally, the
"do_i2c" function test command interfered with
common/cmd_i2c.c's "do_i2c" when CONFIG_I2C_CMD_TREE was defined.

The functions were also made static as they are not globally accessed.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2009-06-12 20:39:45 +02:00
Peter Tyser
a056b1ce9e Marvell: i2c cleanup
The following changes were made, primarily to bring the Marvell i2c
driver in line with U-Boot's current I2C API:
- Made i2c_init() globally accessible
- Made i2c_read() and i2c_write() return an integer
- Updated i2c_init() calls to pass in CONFIG_SYS_I2C_SLAVE in the
  offhand chance someone adds slave support in the future

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2009-06-12 20:39:45 +02:00
Peter Tyser
54afc6ee10 cpci750: i2c cleanup
The following changes were made, primarily to bring the cpci750 i2c
driver in line with U-Boot's current I2C API:
- Made i2c_init() globally accessible
- Made i2c_read() and i2c_write() return an integer
- Updated i2c_init() calls to pass in CONFIG_SYS_I2C_SLAVE in the
  offhand chance someone adds slave support in the future

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2009-06-12 20:39:45 +02:00
Haiying Wang
b2aab386e9 85xx: Add UART1 support for MPC8569MDS
MPC8569 UART1 signals are muxed with PortF bit[9-12], we need to define
those pins before using UART1.

Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-06-12 00:11:10 -05:00
Wolfgang Denk
de7cf709eb EP88x: fix broken linker script
Signed-off-by: Wolfgang Denk <wd@denx.de>
Tested-by: Mikhail Zaturenskiy <mzaturenskiy@shoppertrak.com>
2009-06-09 23:10:01 +02:00
Dave Liu
16e7559c08 85xx: Fix the wrong BCSR address of 8569MDS
The BCSR17[7] = 1 will unlock the write protect of FLASH.
The WP# pin only controls the write protect of top/bottom sector,
That is why we can save env, but we can't write the first sector
before the patch.

Signed-off-by: Dave Liu <daveliu@freescale.com>
2009-06-09 22:58:32 +02:00
Dave Liu
1b5291dddf 85xx: Fix the clock adjust of mpc8569mds board
Currently the clk_adj is 6 (3/4 cycle), The settings will cause
the DDR controller hang at the data init. Change the clk_adj
from 6 to 4 (1/2 cycle), make the memory system stable.

Signed-off-by: Dave Liu <daveliu@freescale.com>
2009-06-09 22:58:05 +02:00
Remy Bohmer
e5a3bc2401 Add config option for disabling DM9000-SROM support.
Some boards do not have SROM support for the DM9000 network adapter.
Instead of listing these board names in the driver code, make this
option configurable from the board config file.

It also removes a build warning for the at91sam9261ek board:
'dm9000x.c:545: warning: 'read_srom_word' defined but not used'

And it repaires the trizepsiv board build which was broken around the
same routines

Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-06-08 22:57:21 -07:00
Wolfgang Denk
dfcd7f2160 Redundant Environment: protect full sector size
Several boards used different ways to specify the size of the
protected area when enabling flash write protection for the sectors
holding the environment variables: some used CONFIG_ENV_SIZE and
CONFIG_ENV_SIZE_REDUND, some used CONFIG_ENV_SECT_SIZE, and some even
a mix of both for the "normal" and the "redundant" areas.

Normally, this makes no difference at all. However, things are
different when you have to deal with boards that can come with
different types of flash chips, which may have different sector
sizes.

Here we may have to chose CONFIG_ENV_SECT_SIZE such that it fits the
biggest sector size, which may include several sectors on boards using
the smaller sector flash types. In such a case, using CONFIG_ENV_SIZE
or CONFIG_ENV_SIZE_REDUND to enable the protection may lead to the
case that only the first of these sectors get protected, while the
following ones aren't.

This is no real problem, but it can be confusing for the user -
especially on boards that use CONFIG_ENV_SECT_SIZE to protect the
"normal" areas, while using CONFIG_ENV_SIZE_REDUND for the
"redundant" area.

To avoid such inconsistencies, I changed all sucn boards that I found
to consistently use CONFIG_ENV_SECT_SIZE for protection. This should
not cause any functional changes to the code.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Paul Ruhland
Cc: Pantelis Antoniou <panto@intracom.gr>
Cc: Stefan Roese <sr@denx.de>
Cc: Gary Jennejohn <garyj@denx.de>
Cc: Dave Ellis <DGE@sixnetio.com>
Acked-by: Stefan Roese <sr@denx.de>
2009-06-04 00:16:16 +02:00
Graf Yang
ab68790798 Blackfin: bf518f-ezbrd: setup portmux for async flash
The pins for async memory where parallel flash lives are not enabled by
default, so make sure we mux them as needed.

Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-05-25 22:38:42 -04:00
Wolfgang Denk
e26ad0eabd Minor Coding Style fix; update CHANGELOG.
Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-05-15 22:32:57 +02:00
Detlev Zundel
792a09eb9d Fix e-mail address of Gary Jennejohn.
Signed-off-by: Detlev Zundel <dzu@denx.de>
2009-05-15 22:11:59 +02:00
Detlev Zundel
60bbcf0cc6 powerpc/inka4x0: Remove left-over ide reset code.
The pin which was used in preliminary versions of the board for ide
reset is really connected to the rtc clock.

Signed-off-by: Detlev Zundel <dzu@denx.de>
2009-05-15 21:31:24 +02:00
Detlev Zundel
890a017a8a arm/imx31_phycore: Fix bi_arch_number
Signed-off-by: Detlev Zundel <dzu@denx.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-15 10:32:40 +02:00
Sergey Lapin
c63254ef56 AFEB9260 network fix
AFEB9260 uses PA10, PA11 for ETX2 and ETX3.
Also, due to extarnal pull-up on IRQ line, Micrel PHY ID is 1 after reset sequence,
not 0.

Signed-off-by: Sergey Lapin <slapin@ossfans.org>
2009-05-13 01:17:17 +02:00
Graf Yang
f8ddcd5822 Blackfin: bf518f-ezbrd: reset ethernet PHY during init
We don't know what state the ethernet PHY is in when starting up, so make
sure we set it to a sane state.  This fixes troubles seen when Linux boots
up, configures the PHY is a non-default state, and then the system reboots
into U-Boot which previously expected a reset state only.

Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-05-06 08:47:37 -04:00
Mike Frysinger
02778f2f1b Blackfin: fix booting with older bootroms (no EVT1)
When dropping jump block support, the assumption was that all bootroms
supported entry point redirection via the EVT1 register.  Unfortunately,
this turned out to be incorrect for the oldest Blackfin parts (BF533-0.2
and older and BF561).  No one really noticed earlier because these parts
usually are booted by bypassing the bootrom entirely, and older BF533
parts are not supported at all (too many anomalies).

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-05-06 08:47:21 -04:00
Dirk Behme
ac9140037a OMAP3: Beagle: Set pinmux conditionally for Rev C boards
The Beagle Rev C boards pull UART2 from an alternate set of balls.

Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
2009-04-30 23:53:59 +02:00
Wolfgang Denk
ccb71dfac9 Merge branch 'master' of git://git.denx.de/u-boot-arm 2009-04-30 23:01:08 +02:00
Sanjeev Premi
90006e9b33 OMAP3: Remove unused board-types
The board-types defined in struct omap3_sysinfo seem to be
unused. The function display_board_info() is passed
board type as an argument; which is ignored.

This patch removes all uses of board-type, related definitions
and functions.

Signed-off-by: Sanjeev Premi <premi@ti.com>
2009-04-29 21:11:40 +02:00
Heiko Schocher
28afe0160f ids8247: Remove legacy NAND defines
because legacy NAND support is deprecated converting to current
NAND interface. !This just compile, because I have no more the
hardware to test it.

Signed-off-by: Heiko Schocher <hs@denx.de>
2009-04-28 01:22:59 +02:00
Peter Tyser
54e822f959 Replace __asm references with __asm__
__asm__ follows gcc's documented syntax and is generally more common
than __asm.  This change is only asthetic and should not affect
functionality.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2009-04-28 01:02:04 +02:00
Wolfgang Denk
faa5a0c6fc Merge branch 'master' of git://git.denx.de/u-boot-at91 2009-04-24 13:31:02 +02:00
Ilko Iliev
f0a2c7b4b6 at91: add support for the PM9263 board of Ronetix GmbH
The PM9263 board is based on the AT91SAM9263-EK board.

Here is the page on Ronetix website:
http://www.ronetix.at/starter_kit_9263.html

Signed-off-by: Ilko Iliev <iliev@ronetix.at>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-04-16 21:30:48 +02:00
Jean-Christophe PLAGNIOL-VILLARD
dc39ae9513 at91sam9/at91cap: improve clock framework
calculate dynamically the clock rate and pllb setting for usb

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-04-16 21:30:44 +02:00
Stefan Roese
17c1b0e89b ppc4xx: Remove unused code for Sequoia NAND booting version
The current define of get_bus_freq() in the CONFIG_NAND_SPL #ifdef is not
used at all. This patch changes it's define to the currently used value of
133333333 and removes the unnecessary code.

Signed-off-by: Stefan Roese <sr@denx.de>
2009-04-16 09:12:08 +02:00
Stefan Roese
5132106a27 ppc4xx: Fixup chip-selects in dtb for NAND-booting Sequoia
Currently the NOR & NAND support in Linux only works for the "standard"
Sequoia, the version booting for NOR flash. The NAND-booting version
has the chip-selects swapped. Here the chip-select mappings:

"Standard" NOR-booting version:
CS0	NOR
CS3	NAND

NAND-booting version:
CS0	NAND
CS3	NOR

With this path the dtb gets fixed-up, so that the correct chip-select
numbers are patched in the dtb enabling correct NOR & NAND support
in Linux on the NAND-booting Sequoia version.

Signed-off-by: Stefan Roese <sr@denx.de>
2009-04-16 09:12:08 +02:00
Wolfgang Denk
712ac6a1a6 Merge branch 'master' of git://git.denx.de/u-boot-arm 2009-04-05 23:04:30 +02:00
Dirk Behme
1c397508c8 OMAP3: Update Overo pin mux for new expansion board
A new Overo expansion board uses GPIO 14, 21, 22 and 23 for LED's and
switches. This patch changes the pinmux configuration for those pins.
They were previously set up for unused MMC3_DAT4-7.

Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
2009-04-05 12:53:32 +02:00
Jean-Christophe PLAGNIOL-VILLARD
b3acb6cd40 arm: clean cache management
unify arm cache management except for non standard cache as ARM7TDMI

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-04-05 13:06:31 +02:00
Kyungmin Park
ab0689c316 Move machine specific code to board at s3c64xx (v2)
Move machine specific code to smdk6400.
Some board use OneNAND instead of NAND.

Some register MP0_CS_CFG[5:0] are controled by both h/w and s/w.
So it's better to use macro instead of hard-coded value.

Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
2009-04-05 00:30:38 +02:00
Tom Rix
5891151707 OMAP3 Fix multiline formatting in board init files.
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
2009-04-05 00:30:38 +02:00
Wolfgang Denk
c0a14aedc3 Update CHANGELOG, coding style cleanup. 2009-04-05 00:27:57 +02:00
Alan Carvalho de Assis
9abc9ef8fb Small fix to m5282evb
This is just a small fix to get u-boot on m5282evb.

Signed-off-by: Alan Carvalho de Assis <acassis@gmail.com>
2009-04-04 22:47:01 +02:00
Wolfgang Denk
5f58f8d20f Merge branch 'master' of git://git.denx.de/u-boot-at91 2009-04-04 22:15:46 +02:00
Jean-Christophe PLAGNIOL-VILLARD
f82518d7f4 at91rm9200: Reset update
Update the rm9200 reset sequence to try executing a board-specific reset
function and move specific board reset to board.

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-04-04 20:42:21 +02:00
Ulf Samuelsson
cb82a53266 Add support for the AT91RM9200EK Board.
The AT91RM9200-EK Evaluation Board supports the AT91RM9200
ARM9-based 32-bit RISC microcontroller and enables real-time code development
and evaluation.

Here is the chip page on Atmel website:
http://www.atmel.com/dyn/products/tools_card.asp?tool_id=3507

with
	- NOR (cfi driver)
	- DataFlash
	- USB OHCI
	- Net
	- I2C (hard)

Signed-off-by: Ulf Samuelsson <ulf@atmel.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-04-04 20:42:20 +02:00
Jean-Christophe PLAGNIOL-VILLARD
2a325ce3c7 at91rm9200dk: Move conditional compilation to Makefile
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-04-04 20:42:19 +02:00
Jean-Christophe PLAGNIOL-VILLARD
90a92a708d at91: rename DATAFLASH_MMC_SELECT to CONFIG_DATAFLASH_MMC_SELECT
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-04-04 20:42:19 +02:00
Jean-Christophe PLAGNIOL-VILLARD
66932ac392 netstar: fix crc32.c dependancy location
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-04-04 20:07:12 +02:00
Wolfgang Denk
0a9403c8c7 Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx 2009-04-04 20:05:18 +02:00
Wolfgang Denk
83863df04b Fix quoting bug introduced by commit 74de7aef
Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-04-04 17:58:26 +02:00
Kumar Gala
32049b4048 fsl_pci: Move prototypes into fsl_pci.h and remove explicit externs
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-04-04 10:21:30 -05:00
Kumar Gala
c8514622e2 fsl_pci: Renamed immap_fsl_pci.h to fsl_pci.h
Rename the pci header for FSL HW so we can move some prototypes
in there and stop doing explicit externs

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-04-04 10:21:29 -05:00
Wolfgang Denk
0d8cb9c04f Merge branch 'master' of git://git.denx.de/u-boot-blackfin 2009-04-03 22:38:36 +02:00
Detlev Zundel
200779e3e2 Rename common ns16550 constants with UART_ prefix to prevent conflicts
Fix problems introduced in commit
7b5611cdd1 [inka4x0: Add hardware
diagnosis functions for inka4x0] which redefined MSR_RI which is
already used on PowerPC systems.

Also eliminate redundant definitions in ps2mult.h.  More cleanup will
be needed for other redundant occurrences though.

Signed-off-by: Detlev Zundel <dzu@denx.de>
2009-04-03 22:34:07 +02:00
Wolfgang Denk
74de7aefd7 Add "source" command; prepare removal of "autoscr" command
According to the doc/feature-removal-schedule.txt, the "autoscr"
command will be replaced by the "source" command in approximately 6
months from now.

This patch prepares this change and starts a 6 month transition
period as follows:

- The new "source" command has been added, which implements exactly
  the same functionlaity as the old "autoscr" command before
- The old "autoscr" command name is kept as an alias for compatibility
- Command sequences, script files atc. have been adapted to use the
  new "source" command
- Related environment variables ("autoscript", "autoscript_uname")
  have *not* been adapted yet; these will be renamed resp. removed in
  a separate patch when the support for the "autoscr" command get's
  finally dropped.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-04-03 22:01:42 +02:00
Mike Frysinger
f4032d2eec Blackfin: bf533-stamp: drop old spi flash driver
Now that the common SPI flash code supports all the flashes, we can stop
using the old driver.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-04-02 06:42:23 -04:00
Mike Frysinger
d248cfb2d9 Blackfin: bf537-stamp: split CF/IDE code out into dedicated cf-ide.c
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-04-02 06:42:00 -04:00
Mike Frysinger
84a9dda324 Blackfin: bf518f-ezbrd: new board port
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-04-02 06:41:46 -04:00
Mike Frysinger
0c31ddf7b7 Blackfin: bf526-ezbrd: new board port
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-04-02 06:41:42 -04:00
Mike Frysinger
5c45f7cac2 Blackfin: bf538f-ezkit: new board port
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-04-02 06:41:38 -04:00
Mike Frysinger
d9a5d113b9 Blackfin: bf527-ezkit: new board port
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-04-02 06:41:35 -04:00
Mike Frysinger
76d21803dd Blackfin: bf548-ezkit: new board port
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-04-02 06:41:29 -04:00
Wolfgang Denk
dfc91c3395 Merge branch 'master' of git://git.denx.de/u-boot-arm 2009-04-02 00:24:33 +02:00
Kumar Gala
7649a590b5 86xx: Cleanup MP support
* Use CONFIG_MP instead of CONFIG_NUM_CPUS to match 85xx
* Introduce determine_mp_bootpg() helper.  We'll need this to address a
  bug introduced in v2009.03 with 86xx MP booting.  We have to make sure
  to reserve the region of memory used for the MP bootpg() so other
  u-boot code doesn't use it.
* Added dummy versions of cpu_reset(), cpu_status() & cpu_release() to
  allow cmd_mp.c to build and work. In the future we should look at
  implementing all these functions. This could be common w/85xx if we
  use spin tables on 86xx.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-04-01 15:29:44 -05:00
Becky Bruce
f6ef8b7a43 mpc8641hpcn/sbc8641d: Add missing board_lmb_reserves
We're missing the board_lmb_reserve definitions that allow
cpu_mp_lmb_reserve to be called; this means that Linux
is free to reallocate reserved pages.  Linux currently boots
because we're getting lucky - the page we've reserved is
high enough in memory that it isn't allocated by Linux
while we still need it to be in existence.

Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-03-31 22:41:34 -05:00
Ladislav Michl
0fc4f64c59 NetStar: fix NAND
Fix NAND support broken during new NAND code merge. Move those few lines of
code to board/netstar/netstar.c

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
2009-03-31 13:56:20 +02:00
Haiying Wang
765547dc5e MPC85xx: Add MPC8569MDS board support
This patch adds MPC8569MDS board support. The UART, QE UEC1 and UEC2, BRD
EEPROM on I2C2 bus, PCI express and DDR3 SPD are supported in this patch.

Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Hillel Avni <Hillel.Avni@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-03-30 13:33:51 -05:00
Kumar Gala
b0fe93eda6 85xx: Use common LSDMR defines from asm/fsl_lbc.h
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-03-30 13:33:49 -05:00
Detlev Zundel
2344bb8de2 inka4x0: Use proper accessor macros for memory mapped registers.
Signed-off-by: Detlev Zundel <dzu@denx.de>
2009-03-30 09:42:35 +02:00
Detlev Zundel
e979e85fd3 inka4x0: Add hardware diagnosis and RTC in configuration.
This patch adds the board specific communication routines needed by
the external 4543 RTC.

Signed-off-by: Detlev Zundel <dzu@denx.de>
Signed-off-by: Andreas Pfefferle <ap@denx.de>
2009-03-30 09:41:58 +02:00
Detlev Zundel
7b5611cdd1 inka4x0: Add hardware diagnosis functions for inka4x0
This patch adds advanced diagnosis functions for the inka4x0 board.

Signed-off-by: Andreas Pfefferle <ap@denx.de>
Signed-off-by: Detlev Zundel <dzu@denx.de>
2009-03-30 09:41:28 +02:00
Ladislav Michl
04531f3c11 NetStar: add RTC support
Add RTC support.

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
2009-03-29 16:04:51 +02:00
Ladislav Michl
71f7bd305d NetStar: use generic flash driver
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
2009-03-29 16:04:51 +02:00
Ladislav Michl
3f464b0fc0 NetStar: update crcit utility
Make crc32 function to match its prototype. Use more meaningful identifiers.

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
2009-03-29 16:04:51 +02:00
Wolfgang Denk
88685b5f62 VCMA9: fix compile errors
Fix these:
cmd_vcma9.c:82: warning: implicit declaration of function 'eth_getenv_enetaddr'
cmd_vcma9.c:89: error: 'enetaddr' undeclared (first use in this function)

Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-03-29 00:58:16 +01:00
Wolfgang Denk
d2567be915 Fix implicit declaration of function 'eth_[gs]etenv_enetaddr'
...and some other compile warnings.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-03-28 20:16:16 +01:00
Mike Frysinger
0baeca4b09 karef/metrobox/xpedite1k: fix eth_setenv_enetaddr typos
The function is called "eth_setenv_enetaddr", not "eth_putenv_enetaddr".

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Ben Warren <biggerbadderben@gmail.com>
2009-03-27 20:24:31 +01:00
Heiko Schocher
76756e41cd ppc: cleanup compiler errors/warnings
Current u-boot top of tree builds with warnings/errors for
the following boards:

ads5121 cpci5200 mecp5200 v38b IAD210 MBX MBX860T NX823
RPXClassic debris PN62

following patch solves this.

Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
2009-03-27 20:23:32 +01:00
Wolfgang Denk
81005758bc Merge branch 'master' of git://git.denx.de/u-boot-ppc4xx 2009-03-26 22:28:52 +01:00
Wolfgang Denk
aaa0e0812f Merge branch 'master' of git://git.denx.de/u-boot-at91 2009-03-26 22:27:45 +01:00
Stefan Roese
3edf68c47f ppc4xx: Sequoia: Fix TLB reassignment in NAND booting code
This patch fixes a bug in the Sequoia TLB init code to reconfigure
the correct TLB (boot space) after running from RAM. This bug was
introduced with patch 4d332dbeb0
[ppc4xx: Make Sequoia boot vxWorks] which changed the order of the
TLB in the Sequoia init.S file.

Signed-off-by: Stefan Roese <sr@denx.de>
2009-03-26 18:36:40 +01:00
Wolfgang Denk
2c5bd16af1 Merge branch 'master' of git://git.denx.de/u-boot-blackfin 2009-03-25 22:43:25 +01:00
Mike Frysinger
4de1a5daab Blackfin: bf537-stamp: split post code out into dedicated post.c
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-03-24 20:36:31 -04:00
Mike Frysinger
5e8f245743 Blackfin: add support for S25FL128 parts
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-03-24 20:36:31 -04:00
Mike Frysinger
bf1e028bf3 Blackfin: overhaul SPI flash handling to speed things up
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-03-24 20:36:31 -04:00
Mike Frysinger
efcc08cede Blackfin: add support for SST SPI flashes
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-03-24 20:36:30 -04:00
Mike Frysinger
5b8cfbe63f Blackfin: add hack for crappy m25p80
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-03-24 20:36:30 -04:00
Mike Frysinger
751e54c3b7 Blackfin: bf537-stamp: rewrite MAC-in-flash handling
Use the common net eth functions to setup the env/global data with the MAC
address, and properly handle the case where CONFIG_SYS_NO_FLASH is defined.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-03-24 20:36:29 -04:00
Mike Frysinger
23fd959eea Blackfin: bf533-stamp: rewrite startup LED notifications
Again, don't clobber pins that we aren't actually using, and use the common
LED framework rather than our own hob-job-but-not-really-working.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-03-24 20:36:28 -04:00
Wolfgang Grandegger
16f2f5a351 Add multi-chip NAND support for the TQM8548 modules
This patches configures the NAND UPM-FSL driver with multi-chip
support for the Micron MT29F8G08FAB NAND flash memory on the
TQM8548 modules.

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-03-23 15:53:41 -05:00
Wolfgang Grandegger
33846df28f Add wait flags to support board/chip specific delays
The NAND flash on the TQM8548_BE modules requires a short delay after
running the UPM pattern like the MPC8360ERDK board does. The TQM8548_BE
requires a further short delay after writing out a buffer. Normally the
R/B pin should be checked, but it's not connected on the TQM8548_BE.
The corresponding Linux FSL UPM driver uses similar delay points at the
same locations. To manage these extra delays in a more general way, I
introduced the "wait_flags" field allowing the board-specific driver to
specify various types of extra delay.

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-03-23 15:53:40 -05:00
Wolfgang Grandegger
e93c1c169d Add multi chip support to the FSL-UPM driver
This patch adds support for multi-chip NAND devices to the FSL-UPM
driver. The "dev_ready" callback of the "struct fsl_upm_nand" is now
called with the argument "chip_nr" to allow testing the proper chip
select line. The NAND support of the MPC8360ERDK is updated as well.
No other boards are currently using the FSL UPM driver.

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-03-23 15:53:38 -05:00
Mike Frysinger
7e1d212b6d Blackfin: kill off LDR jump block
The Boot ROM uses EVT1 as the entry point so set that rather than having
to use a tiny jump block in the default EVT1 location.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-03-23 15:14:54 -04:00
Mike Frysinger
bc683f58b1 Blackfin: bf537-stamp: move CONFIG_POST handling to COBJS-$(...)
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-03-23 15:14:52 -04:00
Haavard Skinnemoen
8206bfae3a Merge branch 'mimc200' 2009-03-23 10:22:41 +01:00
Nicolas Ferre
df486b1fa3 at91: Support for the at91sam9g20 : Atmel 400Mhz ARM 926ej-s SOC.
AT91sam9g20 is an evolution of the at91sam9260 with a faster clock speed.

The AT91SAM9G20-EK board is an updated revision of the AT91SAM9260-EK board.
It is essentially the same, with a few minor differences.

Here is the chip page on Atmel website:
http://www.atmel.com/dyn/products/product_card.asp?part_id=4337

Signed-off-by: Justin Waters <justin.waters@timesys.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-03-22 14:48:16 +01:00
Jean-Christophe PLAGNIOL-VILLARD
118d168035 cmc_pu2: fix implicit declaration of function 'eth_setenv_enetaddr'
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-03-22 14:28:14 +01:00
Jean-Christophe PLAGNIOL-VILLARD
176c4a982c cmc_pu2: fix misc_init_r prototype
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-03-22 14:28:13 +01:00
Jean-Christophe PLAGNIOL-VILLARD
74c076d6c3 at91sam9/at91cap: move nand drivers to drivers/mtd/nand
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-03-22 13:22:24 +01:00
Jean-Christophe PLAGNIOL-VILLARD
163966087d atmel/at91/boards: compile dataflash partition only when dataflash is
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-03-22 13:22:19 +01:00
Jean-Christophe PLAGNIOL-VILLARD
e2c0476f95 at91sam9/at91cap: move common macb initialisation to cpu
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-03-22 13:22:14 +01:00
Jean-Christophe PLAGNIOL-VILLARD
f3f91f886b at91sam9/at91cap: move common usb host initialisation to cpu
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-03-22 13:22:11 +01:00
Jean-Christophe PLAGNIOL-VILLARD
a484b00b86 at91sam9/at91cap: move common led management to cpu
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-03-22 13:22:08 +01:00
Jean-Christophe PLAGNIOL-VILLARD
7ebafb7ec1 at91sam9/at91cap: move common spi initialisation to cpu
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-03-22 13:22:06 +01:00
Jean-Christophe PLAGNIOL-VILLARD
1332a2a069 at91sam9/at91cap: move common serial initialisation to cpu
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-03-22 13:22:03 +01:00
Stefan Roese
68d7d65100 Separate mtdparts command from jffs2
Currently the mtdparts commands are included in the jffs2 command support.
This doesn't make sense anymore since other commands (e.g. UBI) use this
infrastructure as well now. This patch separates the mtdparts commands from
the jffs2 commands making it possible to only select mtdparts when no JFFS2
support is needed.

Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
2009-03-20 22:39:14 +01:00
Grzegorz Bernacki
5c4fa9b474 Add support for the digsy MTC board.
This is the InterControl custom device based on the MPC5200B chip.

Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
2009-03-20 22:39:14 +01:00
Matthias Fuchs
bb57ad4be7 ppc4xx: Use correct io accessors for esd 405/440 boards
This patch replaces in/out8/16/32 macros by in/out_8/_be16/_be32
macros. Also volatile pointer references are replaced by the
new accessors.

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
2009-03-20 22:39:14 +01:00
Matthias Fuchs
049216f045 ppc4xx: Use correct io accessors for esd 405 boards
This patch replaces in/out8/16/32 macros by in/out_8/_be16/_be32
macros. Also volatile pointer references are replaced by the
new accessors.

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
2009-03-20 22:39:14 +01:00
Matthias Fuchs
a59205d151 ppc4xx: Cleanup linker scripts of esd 4xx boards
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
2009-03-20 22:39:14 +01:00
Matthias Fuchs
2f103ee284 ppc4xx: Update TEXT_BASE for DASA_SIM boards
Fix building DASA_SIM boards by increasing U-Boot's size in flash.

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
2009-03-20 22:39:13 +01:00
Matthias Fuchs
09db8f4de6 ppc4xx: DU405 maintenance fix
-strip unused features
-fix resetting phy

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
2009-03-20 22:39:13 +01:00
Graeme Russ
ece444b42b Move ali512x.h
Moved ali512x.h from include/asm-i386/ic/ to /include

Signed-off-by: Graeme Russ <graeme.russ at gmail.com>
2009-03-20 22:39:13 +01:00
Graeme Russ
6d83e3ac61 Rename SC520 Configuration Options
Options are now all uniformly CONFIG_SYS_SC520_<option>

Signed-off-by: Graeme Russ <graeme.russ at gmail.com>
2009-03-20 22:39:12 +01:00
Trent Piepho
f62fb99941 Fix all linker script to handle all rodata sections
A recent gcc added a new unaligned rodata section called '.rodata.str1.1',
which needs to be added the the linker script.  Instead of just adding this
one section, we use a wildcard ".rodata*" to get all rodata linker section
gcc has now and might add in the future.

However, '*(.rodata*)' by itself will result in sub-optimal section
ordering.  The sections will be sorted by object file, which causes extra
padding between the unaligned rodata.str.1.1 of one object file and the
aligned rodata of the next object file.  This is easy to fix by using the
SORT_BY_ALIGNMENT command.

This patch has not be tested one most of the boards modified.  Some boards
have a linker script that looks something like this:

*(.text)
. = ALIGN(16);
*(.rodata)
*(.rodata.str1.4)
*(.eh_frame)

I change this to:

*(.text)
. = ALIGN(16);
*(.eh_frame)
*(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*)))

This means the start of rodata will no longer be 16 bytes aligned.
However, the boundary between text and rodata/eh_frame is still aligned to
16 bytes, which is what I think the real purpose of the ALIGN call is.

Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
2009-03-20 22:39:12 +01:00
Mike Frysinger
9c150102bc boards: get mac address from env and move load_sernum_ethaddr() to board init
The environment is the canonical storage location of the mac address, so
we're killing off the global data location and moving everything to
querying the env directly.

Rather than have common ppc code call a board-specific function like
load_sernum_ethaddr(), have each board call it in its own board-specific
misc_init_r() function.

The boards that get converted here are:
	- kup4k/kup4x
	- pcs440ep
	- tqm8xx

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Ben Warren <biggerbadderben@gmail.com>
CC: Stefan Roese <sr@denx.de>
2009-03-20 22:39:12 +01:00
Mike Frysinger
92b50ffef9 cmc_pu2: get mac address from environment
The environment is the canonical storage location of the mac address, so
we're killing off the global data location and moving everything to
querying the env directly.

Also rename load_sernum_ethaddr() to misc_init_r() so we don't need to
handle this board specially in common ARM code.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Ben Warren <biggerbadderben@gmail.com>
2009-03-20 22:39:12 +01:00
Mike Frysinger
d8d21e699d boards: move board_get_enetaddr() into board-specific init
The environment is the canonical storage location of the mac address, so
we're killing off the global data location and moving everything to
querying the env directly.

Rather than have the common ppc code have board-specific hooks, move the
board_get_enetaddr() function into the board-specific init functions.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Ben Warren <biggerbadderben@gmail.com>
2009-03-20 22:39:12 +01:00
Mike Frysinger
0107cf66f7 nx823: get mac address from environment
The environment is the canonical storage location of the mac address, so
we're killing off the global data location and moving everything to
querying the env directly.

For the nx823, the serial number is moved out of load_sernum_ethaddr() and
into misc_init_r() as is the env setup.  This lets us kill off the former
function in the process.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Ben Warren <biggerbadderben@gmail.com>
2009-03-20 22:39:11 +01:00
Mike Frysinger
b6b4625d17 boards: get mac address from environment
The boards that get converted here to use the environment for the mac
address rather than global data:
	debris
	mgcoge
	mgsuvd
	muas3001
	netstal
	pn62
	sixnet
	vcma9
	xilinx (the ones that use xilinx_enet)

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Ben Warren <biggerbadderben@gmail.com>
CC: Sangmoon Kim <dogoil@etinsys.com>
CC: Heiko Schocher <hs@denx.de>
CC: David Mueller <d.mueller@elsoft.ch>
CC: Niklaus Giger <niklaus.giger@netstal.com>
CC: Wolfgang Grandegger <wg@denx.de>
CC: Dave Ellis <DGE@sixnetio.com>
CC: Ricardo Ribalda <ricardo.ribalda@uam.es>
2009-03-20 22:39:10 +01:00
Mike Frysinger
06a0c4381a AmigaOneG3SE/enet: get mac address from environment
Always use the MAC address that is stored in the environment first before
falling back to the ROM.  This also cuts out any comparison steps: if the
mac in the env is sane, the ROM is never consulted.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Thomas Frieden <ThomasF@hyperion-entertainment.com>
CC: Ben Warren <biggerbadderben@gmail.com>
2009-03-20 22:39:10 +01:00
Heiko Schocher
1b6275dfb1 8xx: add support for new keymile kmsupx4 board.
This patch adds support for the kmsupx4 board from Keymile,
based on a Freescale MPC852T CPU

- serial console on SMC1
- 32 MB SDRAM
- 32 MB NOR Flash
- Ethernet over SCC3
- I2C Bitbang

Signed-off-by: Heiko Schocher <hs@denx.de>
2009-03-18 20:50:05 +01:00
Heiko Schocher
d044954fe2 8xx, mgsuvd: rename board to a more generic name
renaming the "mgsuvd" board port into "km8xx", because
there come more similar boards from keymile.
Compiling the mgsuvd board with "make mgsuvd_config"
remains.

Signed-off-by: Heiko Schocher <hs@denx.de>
2009-03-18 20:50:04 +01:00
Wolfgang Denk
efb47346d4 Merge branch 'master' of git://git.denx.de/u-boot-coldfire 2009-03-18 00:40:57 +01:00
TsiChung Liew
9017d9325a ColdFire: Fix M5329EVB and M5373EVB nand issue
The Nand flash was unable to read and write properly
due to Nand Chip Select (nCE) setup was in reverse
order. Also, increase the Nand time out value to 60.

Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
2009-03-17 15:58:37 -06:00
Stefan Roese
0b2f38fe3c ppc4xx: lwmon5: Only use one CS (rank) in DDR2 configuration
This patch fixes a problem spotted by Mikhail Zolotaryov on Sequoia with
the DDR2 configuration to only use one CS (rank). As this code is most
likely copied from the original Sequoia version, this error was copied
as well.

This patch also removes some dead code.

Signed-off-by: Stefan Roese <sr@denx.de>
2009-03-17 10:52:36 +01:00
Stefan Roese
9199b9cc8f ppc4xx: PMC440: Only use one CS (rank) in DDR2 configuration
This patch fixes a problem spotted by Mikhail Zolotaryov on Sequoia with
the DDR2 configuration to only use one CS (rank). As this code is most
likely copied from the original Sequoia version, this error was copied
as well.

Signed-off-by: Stefan Roese <sr@denx.de>
2009-03-17 10:52:36 +01:00
Mikhail Zolotaryov
ee86fd15e1 Fix AMCC Sequoia board DDR memory configuration
Sequoia board schematics (DES0211_11_SCH_11.pdf, page 5, unit U1D)
specifies that BankSel#1 is not connected, while bootloader memory
configuration is (board/amcc/sequoia/sdram.c):
       mtsdram(DDR0_10, 0x00000300);
i.e. both Chip Selects used - not correct.

If we change to correct value here:
       mtsdram(DDR0_10, 0x00000100);
memory is accessible OK also.

Signed-off-by: Mikhail Zolotaryov <lebon@lebon.org.ua>
Signed-off-by: Stefan Roese <sr@denx.de>
2009-03-17 10:52:36 +01:00
Wolfgang Denk
b3dd629e78 Prepare 2009.03-rc2
Update CHANEGLOG, fix minor coding style issue.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-03-15 22:40:09 +01:00
Wolfgang Denk
e05825324a Merge branch 'master' of git://git.denx.de/u-boot-sh 2009-03-15 22:15:13 +01:00
Dirk Behme
e6a6a70415 OMAP3: Add support for OMAP3 die ID
Read and store OMAP3 die ID in U-Boot environment.

Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
2009-03-13 23:17:43 +01:00
Yusuke.Goda
94a353611b sh: ap325rxa: Change the wait cycle in the area 5
Signed-off-by: Yusuke Goda <goda.yusuke@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2009-03-13 22:32:27 +09:00
Yoshihiro Shimoda
ada9318252 sh: Add support 32-Bit Extended Address Mode to sh7785lcr
We can built 'make sh7785lcr_32bit_config'. And add new command "pmb"
for this mode. This command changes PMB for using 512MB system memory.

Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2009-03-12 23:58:30 +09:00
Nobuhiro Iwamatsu
3e3eec39de sh: use write{8,16,32} in ms7720se lowlevel_init
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2009-03-12 23:58:29 +09:00
Andy Fleming
48c2b7bb43 fsl: Remove unnecessary debug printfs
These were left in accidentally, and are not really useful unless the
code is as broken as it was when it was being developed.

Signed-off-by: Andy Fleming <afleming@freescale.com>
2009-03-09 17:46:10 -05:00
Wolfgang Denk
014c595f12 Merge branch 'master' of git://git.denx.de/u-boot-mpc83xx
Conflicts:
	lib_ppc/board.c

Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-03-09 00:41:48 +01:00
Heiko Schocher
1e7ed25650 83xx, kmeter: QE_ENET10 errata for Silicon Revision 2.1
old code implemented the QE_ENET10 errata only for Silicon
Revision 2.0. New code reads now the Silicon Revision
register and sets dependend on the Silicon Revision the
values as advised in the QE_ENET10 errata.

Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-03-05 18:21:29 -06:00
Heiko Schocher
118cbe3c35 83xx, kmeter1: autodetect size of DDR II RAM
it is possible that some board variants have different DDR II
RAM sizes. So we autodetect the size of the assembled RAM.

Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-03-05 18:21:17 -06:00
Heiko Schocher
19f0e93041 83xx, kmeter1: add I2C, dtt, eeprom support
This patch adds I2C support for the Keymile kmeter1 board.
It uses the First I2C Controller from the CPU, for
accessing 4 temperature sensors, an eeprom with IVM data
and the booteeprom over a pca9547 mux.

Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-03-05 18:21:17 -06:00
Anton Vorontsov
7e2ec1de1d mpc83xx: MPC837XEMDS: Initialize SerDes before negating PCIE reset signal
The SerDes initialization should be finished before negating the reset
signal according to the reference manual. This isn't an issue on real
hardware, but we'd better stick to the specifications anyway.

Suggested-by: Liu Dave <DaveLiu@freescale.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-03-05 18:13:11 -06:00
Wolfgang Denk
7fe2a98394 Merge branch 'master' of git://git.denx.de/u-boot-video 2009-02-24 22:56:00 +01:00
Wolfgang Denk
89e372cd3d Merge branch 'master' of git://git.denx.de/u-boot-mpc83xx 2009-02-24 22:52:16 +01:00
Guennadi Liakhovetski
a2bb7105a7 ARM: add an "eet" variant of the imx31_phycore board
The "eet" variant of the imx31_phycore board has an OLED display, using a
s6e63d6 display controller on the first SPI interface, using GPIO57 as a
chip-select for it. With this configuration you can display 256 colour BMP
images in 16-bit RGB (RGB565) LCD mode.

Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-02-24 10:44:02 +01:00
Anton Vorontsov
7e91558032 mpc83xx: MPC837XERDB: Add PCIe support
On MPC8377E-RDB and MPC8378E-RDB boards we have PCIe and mini-PCIe
slots. Let's support them.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-02-23 15:52:35 -06:00
Becky Bruce
2331e18b9d mpc8641hpcn: Indicate 36-bit addr map in boot messages
If 36-bit addressing is enabled, print a message on the console
when we boot.

Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
2009-02-23 22:48:17 +01:00
Mark Jackson
58a518c3d8 Setup extra MIMC200 chip selects
Added code to setup the extra Flash and FRAM chip selects as used on the
MIMC200 board.

V2 moves the init code from the common "cpu.c" file into the board specific
setup file.

Signed-off-by: Mark Jackson <mpfj@mimc.co.uk>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2009-02-23 11:16:14 +01:00
Mark Jackson
80534886a7 MIMC200: tidy GCLK init code
Change the MIMC200 startup code to use the built-in (rather than
hard-coded) funtions for setting up gclk outputs.

We'll also move the code to the new, more-appropriate
board_postclk_init() routine.

Signed-off-by: Mark Jackson <mpfj@mimc.co.uk>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2009-02-23 11:13:55 +01:00
Haavard Skinnemoen
7d3921bffb Merge branch 'evk1100-prep' into next 2009-02-23 10:34:46 +01:00
Haavard Skinnemoen
156feb90d2 Merge branch 'mimc200' into next
Conflicts:

	board/mimc/mimc200/mimc200.c
	include/configs/mimc200.h
2009-02-23 10:34:39 +01:00
Olav Morken
d8f2aa3298 AVR32: Make cacheflush cpu-dependent
The AT32UC3A series of processors doesn't contain any cache, and issuing
cache control instructions on those will cause an exception. This commit
makes cacheflush.h arch-dependent in preparation for the AT32UC3A-support.

Signed-off-by: Gunnar Rangoy <gunnar@rangoy.com>
Signed-off-by: Paul Driveklepp <pauldriveklepp@gmail.com>
Signed-off-by: Olav Morken <olavmrk@gmail.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2009-02-23 10:34:23 +01:00
Haavard Skinnemoen
ea393eb1d6 Merge branch 'cleanups' into next 2009-02-23 10:27:15 +01:00
Dirk Behme
cfcdf4a9b3 OMAP3: Pandora: Update pin mux
Clock pin must have input enabled for MMC3 to work.
Also enable pull-ups for cmd/data lines to be consistent
with remaining MMC host pin setup.

Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
2009-02-22 18:29:10 +01:00
Dirk Behme
6530a8bf8a OMAP3: Add OMAP3 auto detection
This patch adds OMAP3 cpu type auto detection based on OMAP3 register
and removes hardcoded values.

Signed-off-by: Steve Sakoman <sakoman@gmail.com>
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
2009-02-22 18:29:10 +01:00
Dirk Behme
f956fd0338 OMAP3: Beagle: Add board revision detection
With BeagleBoard revision C some HW changes are introduced (e.g. PinMUX)
which might need different software handling. For this, GPIO pin 171 (GPIO
module 6, offset 11) can be used to check for board revision. If this pin
is low, we have a rev C board. Else it must be a revision Ax or Bx board.

To handle board differences you can call function beagle_get_revision().
E.g.:

if (beagle_get_revision()) {

/* do special revision C stuff here */

}

Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
2009-02-22 18:29:10 +01:00
Dirk Behme
288f3cd912 OMAP3: Overo: Clean up pin mux and GPIO configuration
* Make Overo GPIO114 an input for touchscreen PENDOWN
* Make Overo GPIO144-147 readable
* Make Overo EHCI pinmux match beagle rev c setup
* Adjust pinmux for SMSC911X network chip support
* Remove unnecessary GPIO setup
* Fix merge error in Makefile

Signed-off-by: Steve Sakoman <sakoman@gmail.com>
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
2009-02-22 18:29:10 +01:00
Jean-Christophe PLAGNIOL-VILLARD
9751a456f7 davinci: fix implicit declaration of function 'davinci_errata_workarounds'
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-02-22 17:49:43 +01:00
Hugo Villeneuve
0cd18fa982 ARM DaVinci: Add common peripherals and modules enable functions.
Taken all the duplicated code for enabling common modules and apply
software workarounds from the board specific code into common
functions. Also added comments explaining the workarounds
(from TI errata documents) and replaced some numerical bit numbers
with more meaningful defines.

Signed-off-by: Hugo Villeneuve <hugo.villeneuve@lyrtech.com>
2009-02-22 13:42:25 +01:00
Alessandro Rubini
d3be1bcae7 Enable Ethernet for Nomadik 8815 Evaluation Kit
This trivially enables Ethernet support in the debug board
by setting up the proper chip select.

Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stnwireless.com>
2009-02-22 13:40:31 +01:00
Wolfgang Denk
09fee8e867 Coding Style cleanup; update CHANGELOG
Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-02-22 01:19:52 +01:00
Heiko Schocher
9e80bb2162 82xx, mgcoge: updates for 2009.03
- activate CS4 for accessing the FPGA
- activate Rx buf len > 1 on SMC
- pram activated
- MTDPARTS_DEFAULT defined
- update the size of the flashes in the DTS
  before booting Linux
- MONITOR_LEN updated to 384k
- added CONFIG_HOSTNAME
- added CONFIG_ENV_BUFFER_PRINT
- Environment size reduced to 16k

Signed-off-by: Heiko Schocher <hs@denx.de>
2009-02-19 21:20:16 +01:00
Heiko Schocher
df909554e2 8xx, mgsuvd: updates for 2009.03
- activate Rx buf len > 1 on SMC
- pram activated
- MTDPARTS_DEFAULT defined
- update the size of the flash in the DTS
  before booting Linux
- MONITOR_LEN updated to 384k
- added CONFIG_HOSTNAME
- added CONFIG_ENV_BUFFER_PRINT
- Environment size reduced to 16k

Signed-off-by: Heiko Schocher <hs@denx.de>
2009-02-19 21:19:45 +01:00
Wolfgang Denk
32482be677 TQM8xxL: make some room in low memory for future needs
THe TQM8xxL use a ahnd-optimized linker script to efficiently use the
small boot sectors in the flash. This patch makes some room in the
first sector to prepare for a size increase of lib_generic/vsprintf.o
by a future patch.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-02-19 14:01:42 +01:00
Wolfgang Denk
44a01a73e8 Merge branch 'master' of git://git.denx.de/u-boot-ppc4xx 2009-02-19 00:50:08 +01:00
Wolfgang Denk
9eb468da3f Merge branch 'master' of git://git.denx.de/u-boot-arm 2009-02-19 00:46:32 +01:00
Wolfgang Denk
b8845abdc0 Fix build errors after making flash_get_info() non-static
Fix for these build problems:
error: static declaration of 'flash_get_info' follows non-static declaration

Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-02-18 22:40:08 +01:00
Stefan Roese
f50fe4bd61 ppc4xx: Some more PMC405 coding-style cleanup
Signed-off-by: Stefan Roese <sr@denx.de>
2009-02-18 14:05:37 +01:00
Matthias Fuchs
2f6eb9170b ppc4xx: Update PMC405 board support
This patch prepares the good old PMC405 board support for
upcoming PMC405V2 patches.

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2009-02-18 13:50:35 +01:00
Matthias Fuchs
c553b5f4a0 ppc4xx: Cleanup PMC405 board support
This patch fixes coding style for PMC405 board support.
Also some unneeded features/code is removed.

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2009-02-18 13:50:29 +01:00
Andy Fleming
e1ac387f46 83xx: Add eSDHC support on 8379 EMDS board
Signed-off-by: Andy Fleming <afleming@freescale.com>
2009-02-16 18:07:43 -06:00
Andy Fleming
80522dc836 85xx: Add eSDHC support for 8536 DS
Signed-off-by: Andy Fleming <afleming@freescale.com>
2009-02-16 18:07:43 -06:00
Andy Fleming
e0c4fac79d TQM85xx: Fix a couple warnings in TQM8548 build
The ecm variable in sdram.c was being declared for all 8548, but only
used by specific 8548 boards, so we make that variable require those
specific boards, too

The nand code was using an index "i" into a table, and then re-using "i"
to set addresses for each upm.  However, then it relied on the old value
of i still being there to enable things.  Changed the second "i" to "j"

Signed-off-by: Andy Fleming <afleming@freescale.com>
2009-02-16 18:06:03 -06:00
Wolfgang Grandegger
cf07a5baec MPC85xx: TQM8548: workaround for erratum DDR 19 and 20
This patch adds the workaround for erratum DDR20 according to MPC8548
Device Errata document, Rev. 1: "CKE signal may not function correctly
after assertion of HRESET". Furthermore, the bug DDR19 is fixed in
processor version 2.1 and the work-around must be removed.

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
2009-02-16 18:06:02 -06:00
Wolfgang Grandegger
080408fdc7 MPC85xx: TQM8548: use cache for AG and BE variants
This patch makes accesses to the system memory cachable by removing the
caching-inhibited and guarded flags from the relevant TLB entries for
the TQM8548_BE and TQM8548_AG modules. FYI, the Freescale MPC85* boards
are configured similarly.

This results in a big averall performace improvement. TFTP downloads,
NAND Flash accesses, kernel boots, etc. are much faster.

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
2009-02-16 18:06:02 -06:00
Wolfgang Grandegger
dc5f55d636 MPC85xx: TQM8548_AG: add 1 GiB DDR2-SDRAM configuration
This patch add support for the 1 GiB DDR2-SDRAM on the TQM8548_AG
module.

Signed-off-by: Jens Gehrlein <sew_s@tqs.de>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
2009-02-16 18:06:01 -06:00
Wolfgang Grandegger
88b0e88d18 MPC85xx: TQM8548: fix SDRAM timing for 533 MHz
According to new TQM8548 timing specification:
Refresh Recovery: 34 -> 53 clocks
CKE pulse width:  1 -> 3 cycles
Window for four activities: 13 -> 14 cycles

Signed-off-by: Jens Gehrlein <sew_s@tqs.de>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
2009-02-16 18:06:00 -06:00
Wolfgang Grandegger
ad7ee5d43b MPC85xx: TQM8548: add support for the TQM8548_BE module
The TQM8548_BE is a variant of the TQM8548 module with NAND and CAN
interface. With NAND support, the image is significantly larger and
TEXT_BASE is adjusted accordingly. U-Boot can be built for this
module with "$ make TQM8548_BE_config".

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
2009-02-16 18:05:59 -06:00
Wolfgang Grandegger
a318234878 MPC85xx: TQM85xx: make standard PCI/PCI-X configurable
The TQM8548_AG module does not have the standard PCI/PCI-X interface
connected but just the PCI Express interface . So far it was not
possible to disable it without disabling the complete PCI interface
(CONFIG_PCI) including PCI Express.

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
2009-02-16 18:05:58 -06:00
Wolfgang Grandegger
31ca9119c3 MPC85xx: TQM85xx: fix flash protection for boot loader
As the reset vector is located at 0xfffffffc, all flash sectors from the
beginning of the U-Boot binary to 0xffffffff must be protected. On the
TQM8548-AG having small sectors at the end of the flash it happened that
the last two sector were not protected and an "erase all" left an
un-bootable system behind:

Bank # 2: CFI conformant FLASH (32 x 16)  Size: 32 MB in 270 Sectors
  AMD Standard command set, Manufacturer ID: 0xEC, Device ID: 0x257E
  Erase timeout: 8192 ms, write timeout: 1 ms

  FFFA0000 E RO   FFFC0000   RO   FFFE0000   RO   FFFE4000   RO   FFFE8000   RO
  FFFEC000   RO   FFFF0000   RO   FFFF4000   RO   FFFF8000 E      FFFFC000

The same bug seems to be in drivers/mtd/cfi_flash.c:flash_init() and many
board BSPs as well.

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
2009-02-16 18:05:58 -06:00
Peter Tyser
4ef630df77 86xx: Reset update
Update the 86xx reset sequence to try executing a board-specific reset
function.  If the board-specific reset is not implemented or does not
succeed, then assert #HRESET_REQ.  Using #HRESET_REQ is a more standard
reset procedure than the previous method and allows all board
peripherals to be reset if needed.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2009-02-16 18:05:56 -06:00
Kumar Gala
cb69e4de87 85xx: print boot header info to distinquish 36-bit addr map on MPC8572 DS
Added some info that is printed out when we boot to distiquish if we
built MPC8572DS_config vs MPC8572DS_36BIT_config since they have
different address maps.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-02-16 18:05:54 -06:00
Andy Fleming
feede8b070 Fixup SGMII PHY ids in the device tree
The device tree's PHY addresses need to be fixed up if we're using the
SGMII Riser Card.

The 8572, 8536, and 8544 DS boards were modified to call this function.

Code idea taken from Liu Yu <yu.liu@freescale.com>

Signed-off-by: Andy Fleming <afleming@freescale.com>
2009-02-16 18:05:54 -06:00
Kumar Gala
b67305120a 85xx: Fix bug in device tree setup in 36-bit physical confg
In the 36-bit physical config for MPC8572DS when need the start address
of memory and it size to be kept in phys_*_t instead of a ulong since
we support >4G of memory in the config and ulong cant represent that.
Otherwise we end up seeing the memory node in the device tree reporting
back we have memory starting @ 0 and of size 0.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-02-16 18:05:52 -06:00
Kumar Gala
ad97dce184 85xx: Fix address map for 36-bit config of MPC8572DS
When we introduced the 36-bit config of the MPC8572DS board we had the
wrong PCI MEM bus address map.  Additionally, the change to the address
map exposes a small issue in our dummy read on the ULI bus.  We need
to use the new mapping functions to handle that read properly in the
36-bit config.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-02-16 18:05:52 -06:00
Stefan Roese
cef0efaf2f ppc4xx: Fix problem with board_eth_init() vs cpu_eth_init() on AMCC boards
Some AMCC eval boards do have a board_eth_init() function calling
pci_eth_init(). These boards need to call cpu_eth_init() explicitly now
with the new eth_init rework.

Signed-off-by: Stefan Roese <sr@denx.de>
2009-02-12 06:08:07 +01:00
Wolfgang Denk
f15c6515fc Coding style cleanup; update CHANGELOG
Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-02-12 00:08:39 +01:00
Becky Bruce
49f46f3bf0 mpc8641hpcn: Clean up PCI mapping concepts
Clean up PCI mapping concepts in the 8641 config - rename _BASE
to _BUS, as it's actually a PCI bus address, separate virtual
and physical addresses into _VIRT and _PHYS, and use each
appopriately.

Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
2009-02-10 00:30:17 +01:00
Becky Bruce
d35ae5a938 powerpc: Move duplicated BAT defines to mmu.h
The BAT fields are architected; there's no need for these to be in
cpu-specific files.  Drop the duplication and move these to
include/asm-ppc/mmu.h.  Also, remove the BL_xxx defines that were only
used by the alaska board, and switch to using the BATU_BL_xxx defines
used by all the other boards.  The BL_ defines previously in use
had to be shifted into the proper position for use, which was inefficient.

Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
2009-02-10 00:27:40 +01:00
Becky Bruce
2ecca34017 mpc8641hpcn: Set up outbound pci windows before inbound
Because the inbound pci windows are mapped generously, set up
the more specific outbound windows first.  This way, when we
search the pci regions for something, we will hit on the more
specific region.  This can actually be a problem on systems
with large amounts of RAM.

Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
2009-02-10 00:26:45 +01:00
Ilya Yanok
0d19f6c8cb qong: support for Dave/DENX QongEVB-LITE board
This patch adds support for Dave/DENX QongEVB-LITE i.MX31-based board.

Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-02-10 00:22:31 +01:00
Kumar Gala
ff4e66e93c pci: Rename PCI_REGION_MEMORY to PCI_REGION_SYS_MEMORY for clarity
The PCI_REGION_MEMORY and PCI_REGION_MEM are a bit to similar and
can be confusing when reading the code.

Rename PCI_REGION_MEMORY to PCI_REGION_SYS_MEMORY to clarify its used
for system memory mapping purposes.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-02-07 23:50:04 +01:00
Wolfgang Denk
045639397d Merge branch 'master' of git://git.denx.de/u-boot-blackfin 2009-02-07 22:53:45 +01:00
Wolfgang Denk
1b33a62bf9 Merge branch 'master' of git://git.denx.de/u-boot-mpc5xxx 2009-02-07 22:08:53 +01:00
Mike Frysinger
4b7e3d045c Blackfin: move default boot SPI CS to common code
Move the default SPI CS that we boot from into common code so that it can
be used in other SPI drivers and environment settings.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-02-05 21:25:36 -05:00
Ralph Kondziella
70a4da45e1 ADS5121 Add PATA support
Original patch from Ralph Kondziella
plus clean up by Wolfgang Denk
plus changes by John Rigby
    use ips clock not lpc
    port forward to current u-boot release

Signed-off-by: Ralph Kondziella <rk@argos-messtechnik.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: John Rigby <jrigby@freescale.com>
2009-02-03 15:40:29 -07:00
Martha Marx
abfbd0ae49 ADS5121 Add IC Ident Module (IIM) support
IIM (IC Identification Module) is the fusebox for the mpc5121.
Use #define CONFIG_IIM to turn on the clock for this module
use #define CONFIG_CMD_FUSE to add fusebox commands.
Fusebox commands include the ability to read
the status, read the register cache, override the register cache,
program the fuses and sense them.

Signed-off-by: Martha Marx <mmarx@silicontkx.com>
Signed-off-by: John Rigby <jrigby@freescale.com>
2009-02-03 15:40:20 -07:00
John Rigby
14d19cd1bc ADS5121 Fix rev2 silicon pci iopad config
Reset config is not correct

Signed-off-by: John Rigby <jrigby@freescale.com>
2009-02-03 09:25:51 -07:00
John Rigby
4c154252c4 ADS5121 DIU Add diu_bmp_addr env
Add support for using a bmp other than
FSL_Logo_BMP for the DIU splash screen.

Can now set the env var "diu_bmp_addr" to
the address of a BMP in flash to use instead
of the default FSL_Logo_BMP.

Signed-off-by: Martha Marx <mmarx@silicontkx.com>
Signed-off-by: John Rigby <jrigby@freescale.com>
2009-02-03 09:25:51 -07:00
John Rigby
92c20fbd3a ADS5121 DIU Make inclusion of FSL logo optional
Make inclusion of FSL logo optional and
turn it off by default.

Signed-off-by: John Rigby <jrigby@freescale.com>
2009-02-03 09:25:51 -07:00
Mike Frysinger
6e87ea0ca9 Blackfin: add port muxing for BF51x SPI
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-02-02 12:27:16 -05:00
Wolfgang Denk
6c6e042ab3 Merge branch 'master' of git://git.denx.de/u-boot-arm 2009-02-01 21:38:07 +01:00
Wolfgang Denk
ee924e0030 Merge branch 'master' of git://git.denx.de/u-boot-net 2009-02-01 21:31:37 +01:00
Jean-Christophe PLAGNIOL-VILLARD
cfca33837e move Samsung's board to board/samsung
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-01-29 15:29:43 +01:00
Jean-Christophe PLAGNIOL-VILLARD
e4943ec574 move ARM Ltd. to vendor dir
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-01-29 12:07:21 +01:00
Larry Johnson
f20405e316 ppc4xx: Add variable "korat_usbcf" for Korat board
The new environment variable "korat_usbcf" selects the USB
port used by the Korat board's CompactFlash controller.

Signed-off-by: Larry Johnson <lrj@acm.org>
Signed-off-by: Stefan Roese <sr@denx.de>
2009-01-29 10:55:56 +01:00
Mike Frysinger
75edebe301 Move is_valid_ether_addr() to include/net.h
Import the is_valid_ether_addr() function from the Linux kernel.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-01-28 23:59:27 -08:00
Wolfgang Denk
1fbcbe9a95 85xx: Fix compile breakage with sbc8540 and sbc8560
This fixes an error which raises just a warning:
sbc8560.c:250: warning: passing argument 2 of 'strmhz' makes integer from pointer without a cast

Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-01-28 23:10:32 +01:00
Dirk Behme
7379f45a7b OMAP3: Add Zoom1 board support
Support for Zoom MDK with OMAP3430. Details of Zoom MDK available here:
http://www.logicpd.com/products/devkit/ti/zoom_mobile_development_kit

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
2009-01-28 21:40:16 +01:00
Dirk Behme
2be2c6cc67 OMAP3: Add Pandora support
Add Pandora support.

Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
2009-01-28 21:39:58 +01:00
Dirk Behme
ad9bc8e52d OMAP3: Add EVM board
Add EVM board support.

Signed-off-by: Manikandan Pillai <mani.pillai@ti.com>
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
2009-01-28 21:39:58 +01:00
Dirk Behme
9d0fc8110e OMAP3: Add Overo board
Add Overo board support.

Signed-off-by: Steve Sakoman <sakoman@gmail.com>
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
2009-01-28 21:39:57 +01:00
Dirk Behme
f904cdbb68 OMAP3: Add common power code, README, and BeagleBoard
Add BeagleBoard support, common power code and README.

Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
2009-01-28 21:39:15 +01:00
Wolfgang Denk
6b7243aa89 Merge branch 'master' of git://git.denx.de/u-boot-usb 2009-01-28 21:09:46 +01:00
Wolfgang Denk
ee64d0acc9 Merge branch 'master' of git://git.denx.de/u-boot-blackfin 2009-01-28 21:09:32 +01:00
Kumar Gala
9cda4f104b 85xx: Fix compile breakage with MPC8540EVAL
Configuring for MPC8540EVAL board...
mpc8540eval.c: In function 'checkboard':
mpc8540eval.c:53: error: invalid operands to binary /
make[1]: *** [mpc8540eval.o] Error 1

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-01-28 21:01:52 +01:00
Thomas Abraham
538ef96771 usb : musb : Enabling DM6446 (TI DaVinci) USB module power
Enabling DM6446 (TI DaVinci) USB module power and MUSB low-level
controller hook up to USB core layer.

Signed-off-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: Swaminathan S <swami.iyer@ti.com>
Signed-off-by: Thomas Abraham <t-abraham@ti.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
2009-01-28 19:57:30 +01:00
Thomas Abraham
a9d39ebe91 usb : musb : Adding USB VBUS enable functionality for DM644x DVEVM
Adding USB VBUS enable functionality for DM644x DVEVM (TI DaVinci)
platform.

Signed-off-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: Swaminathan S <swami.iyer@ti.com>
Signed-off-by: Thomas Abraham <t-abraham@ti.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
2009-01-28 19:57:30 +01:00
Mike Frysinger
fe033ad6d0 Blackfin: fixup misc warnings such as printf's and missing casts
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-01-28 13:27:28 -05:00
Mike Frysinger
1f4a3bb503 Blackfin: convert old boards to use COBJS-y Makefile style
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-01-28 13:27:28 -05:00
Mike Frysinger
1f75d6f0ff Blackfin: bf533-stamp: rewrite resource swap logic
The old swap function tended to clobber unrelated pins and screw up masks.
Rewrite the thing from scratch so it only uses the resources it needs.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-01-28 13:27:28 -05:00