The name "se" is used in upstream Linux device trees and has been for
ages, long before this U-Boot-ism was introduced. Same goes for the
existing compatible. Get rid of that.
[vzapolskiy: removed a ready change in the driver]
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
This adds a simple Northstar "BRCMNS" board to be used with
the BCM4708x and BCM5301x chips.
The main intention is to use this with the D-Link DIR-890L
and DIR-885L routers for loading the kernel into RAM from
NAND memory using the BCH-1 ECC and using the separately
submitted SEAMA load command, so we are currently not adding
support for things such as networking.
The DTS file is a multiplatform NorthStar board, designed to
be usable with several NorthStar designs by avoiding any
particulars not related to the operation of U-Boot.
If other board need other ECC for example, they need to
create a separate DTS file and augment the code, but I don't
know if any other users will turn up.
Cc: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This brings in the main SoC device tree used by the
Broadcom Northstar chipset, i.e. BCM4709x and BCM5301x.
This is taken from the v6.3 Linux kernel.
Cc: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The MNT Reform 2 is a modular DIY laptop. In its initial version it
is based on the BoundaryDevices i.MX8MQ SoM. Some parts have been
lifted from BoundaryDevices official U-Boot downstream project.
Signed-off-by: Patrick Wildt <patrick@blueri.se>
Tested-by: Vagrant Cascadian <vagrant@debian.org>
Tested-by: Vagrant Cascadian <vagrant@debian.org>
Signed-off-by: Stefano Babic <sbabic@denx.de>
On sunxi boards, SPL looks for U-Boot at a 32 KiB offset, unless SPL is
larger than 32 KiB, in which case U-Boot immediately follows SPL. See
the logic in spl_mmc_get_uboot_raw_sector() and spl_spi_load_image().
In two cases, the existing binman description mismatches the SPL code.
For 64-bit boards, binman would place U-Boot immediately following SPL,
even if SPL is smaller than 32 KiB. This can happen when SPL MMC support
is disabled (i.e. when booting from SPI flash).
In contrast, for 32-bit boards, binman would place U-Boot at 32 KiB,
even if SPL is larger than that. This happens because the 'offset'
property does not consider the size of previous entries.
Fix both issues by setting a minimum size for the SPL entry, which
exactly matches the logic in the SPL code. Unfortunately, this size must
be provided as a magic number, since none of the relevant config symbols
(SPL_PAD_TO, SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR, and SYS_SPI_U_BOOT_OFFS)
are guaranteed to be defined in all cases.
Fixes: cfa3db602c ("sunxi: Convert 64-bit boards to use binman")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This reverts commit 5717294230. This
does not exist in upstream kernel.org and breaks boot on DRA7-EVMs.
Drop the same.
Signed-off-by: Andrew Davis <afd@ti.com>
This is a collection of all the whitespace, renames, comment, and other
changes that should not change the DT functionality from Linux v6.3-rc6.
Signed-off-by: Andrew Davis <afd@ti.com>
This is a collection of all the whitespace, renames, comment, and other
changes that should not change the DT functionality from Linux v6.3-rc6.
Signed-off-by: Andrew Davis <afd@ti.com>
This is a collection of all the whitespace, renames, comment, and other
changes that should not change the DT functionality from Linux v6.3-rc6.
Signed-off-by: Andrew Davis <afd@ti.com>
This is a collection of all the whitespace, renames, comment, and other
changes that should not change the DT functionality from Linux v6.3-rc6.
Signed-off-by: Andrew Davis <afd@ti.com>
This is a collection of all the whitespace, renames, comment, and other
changes that should not change the DT functionality from Linux v6.3-rc6.
Signed-off-by: Andrew Davis <afd@ti.com>
Several DTS files have been updated in the Linux kernel with a new
PADCONF macro replacing the IOPAD version. Sync for the same here.
Signed-off-by: Andrew Davis <afd@ti.com>
- Add rk3588 evb support;
- Update pinctrl for rk3568 and rk3588;
- Update rk3288 dts;
- Update mmc support for rk3568 and rk3588;
- Add rng support for rk3588;
- Add DSI support for rk3568;
- Some other misc fixes in dts, config, driver;
_ Add usb_pgood_delay for ST boards
_ increase malloc size for pre-reloc for stm32mp15
_ Set CONFIG_USB_HUB_DEBOUNCE_TIMEOUT=2s for stm32mp15
dts:
_ Add QSPI support on STM32MP13x SoC family
_ Add FMC support on STM32MP13x SoC family
drivers/machine:
_ pinctrl_stm32: Add slew rate support for stm32_pinctrl_get_pin_muxing()
_ spi: stm32_qspi: Remove useless struct stm32_qspi_flash
_ rawnand: stm32_fmc2: remove unsupported EDO mode
_ stm32mp: fix various array bounds checks
-----BEGIN PGP SIGNATURE-----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=3Txq
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20230419' of https://source.denx.de/u-boot/custodians/u-boot-stm
configs:
_ Add usb_pgood_delay for ST boards
_ increase malloc size for pre-reloc for stm32mp15
_ Set CONFIG_USB_HUB_DEBOUNCE_TIMEOUT=2s for stm32mp15
dts:
_ Add QSPI support on STM32MP13x SoC family
_ Add FMC support on STM32MP13x SoC family
drivers/machine:
_ pinctrl_stm32: Add slew rate support for stm32_pinctrl_get_pin_muxing()
_ spi: stm32_qspi: Remove useless struct stm32_qspi_flash
_ rawnand: stm32_fmc2: remove unsupported EDO mode
_ stm32mp: fix various array bounds checks
Add sdhci node to SPL and u-boot,spl-boot-order. Also add more supported
mmc modes and pinctrl.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add a node for the trng found on RK3588 SoCs.
Changes in V3:
- Added Reviewed-By tag.
Changes in V2:
- None
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Sync the sdmmc node from linux-next, include required nodes in SPL and
imply Kconfig options required for functional sdmmc clk in SPL and
U-Boot proper.
This make it possible for both SPL and U-Boot proper to configure sdmmc
clocks. In SPL, before TF-A is loaded, scru regs is configured, in
U-Boot proper a SCMI message is sent to TF-A.
Fixes: 95c8656b72 ("ARM: dts: rockchip: rk3588s-u-boot: Add sdmmc node")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Running U-Boot from a SD-card on ROCK 5 Model B fails to load atf using
DMA and prints debug_uart messages.
<debug_uart>
<debug_uart>
U-Boot SPL 2023.04-rc3 (Mar 12 2023 - 00:30:16 +0000)
Trying to boot from MMC1
## Checking hash(es) for config config-1 ... OK
## Checking hash(es) for Image atf-1 ... sha256 error!
Bad hash value for 'hash' hash node in 'atf-1' image node
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###
Use fifo-mode to disable DMA in SPL, add same-as-spl to boot-order and
remove DEBUG_UART_ANNOUNCE option to fix this.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync rk3066/rk3188 DT files from Linux.
This is the state as of linux-next v6.2-rc4.
New nfc node for MK808 rk3066a.
CRU nodes now have a clock property.
To prefend dtoc errors a fixed clock must also be
included for tpl/spl in the rk3xxx-u-boot.dtsi file.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The gpio node names are made generic, but without
gpio bank ID. Add gpio-ranges to rk3188-u-boot.dtsi
for now till a better method is found.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The gpio node names are made generic, but without
gpio bank ID. Add gpio-ranges to rk3066a-u-boot.dtsi
for now till a better method is found.
Disable gpio6 as the driver gives an error code
on return as status.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In order to better compare the Linux rk3288.dtsi
version 6.3 -rc2 with the U-Boot version partial
sync the pwm nodes.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In order to better compare the Linux rk3288.dtsi
version 6.3 -rc2 with the U-Boot version partial
sync the vop/lvds/mipi/hdmi nodes.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # chromebook-jerry
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The rk3288 edp node has a phy node in Linux with a clock
property while current U-Boot driver expects this clock
on position index 1. Move U-Boot-specific DT clock properties
to rk3288-u-boot.dtsi and partially sync the edp node.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # chromebook-jerry
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In order to better compare the Linux rk3288.dtsi
version 6.3 -rc2 with the U-Boot version partial
sync the grf and pmu nodes.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # chromebook-jerry
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In order to better compare the Linux rk3288.dtsi version
with the U-Boot version move the io-domains nodes.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: John Keeping <john@metanate.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # chromebook-jerry
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
rk3588 evb1 v10 is a evalution board from Rockchip, it is a dev board for
rockchip and also a reference board for board vendors.
Hardware:
SoC: RK3588
DRAM: LPDDR4X 8GB
Debug: UART2 via USB
PCIe: 3x4 *1
SATA *2
HDMI out *2
HDMI IN *1
USB2.0 Host *2
USB3.0 Host *1
Type C *1
MIPI DSI panel
dts Sync from Linux v6.2.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Jagan Teki <jagan@edgeble.ai>
Add QSPI support on STM32MP13x SoC family
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Import the dts files from linux-amlogic/for-next (Linux 6.4-rc1) and
add the old PHY reset bindings for dwmac to the u-boot.dtsi until we
support the new bindings in the PHY node. Without this the PHY is not
functional in u-boot or Linux.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230323143142.780306-13-christianshewitt@gmail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Import the device-tree from linux-amlogic/for-next (Linux 6.4-rc1)
to support the Radxa-Zero2 board.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230323143142.780306-10-christianshewitt@gmail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Import the device-tree from linux-amlogic/for-next (Linux 6.4-rc1)
and omit the NPU node from the A311D board variant dts as this is
not supported under U-Boot.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230323143142.780306-7-christianshewitt@gmail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Import the board dts from the linux-amlogic/for-next (6.4-rc1)
branch. This involves spliting the BPI-M5 dts into a dtsi and
then reusing this for the M2-Pro.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230323143142.780306-4-christianshewitt@gmail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Add support for both the BananaPi BPI-CM4 module and the BananaPi
baseboard which is compatible with the RaspberryPi CM4IO baseboard.
The BananaPi BPI-CM4 module follows the CM4 specifications at [1],
but with a single HDMI port and a single DSI output.
The current CM4IO baseboard DT should work fine on the Raspberry CM4
baseboard and other derivatives baseboards, but proper DT should
be written for other baseboards.
[1] https://datasheets.raspberrypi.com/cm4io/cm4io-datasheet.pdf
Link: https://lore.kernel.org/r/20230307-u-boot-cm4-v1-2-43f5a393cd37@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
This board is configured with CONFIG_USB1_VBUS_PIN="PH24", but no
regulator exists in its device tree. Add the regulator, so USB will
continue to work when the PHY driver switches to using the regulator
uclass instead of a GPIO.
Update the device tree here because it does not exist in Linux.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
- improve tegra DC driver to work with panel ops and implement
native 180 degree panel rotation support
- add T30 support to tegra DC driver
- add DSI driver (based on mainline Linux one with minor
adjustments, only T30 tested)
- add get_display_timing ops to simple panel driver
- extend simple panel driver to use it for MIPI DSI panels
which do not require additional DSI commands for setup
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCZDBwUw4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXL3+AJ9EkQKAWXZtlYdAOVl4/nzJnuTCAQCfY58zkDsw
TnAlwmMGWFl3RF6yGXY=
=uYUp
-----END PGP SIGNATURE-----
Merge tag 'video-20230407' of https://source.denx.de/u-boot/custodians/u-boot-video
- fix building sandbox without SDL
- improve tegra DC driver to work with panel ops and implement
native 180 degree panel rotation support
- add T30 support to tegra DC driver
- add DSI driver (based on mainline Linux one with minor
adjustments, only T30 tested)
- add get_display_timing ops to simple panel driver
- extend simple panel driver to use it for MIPI DSI panels
which do not require additional DSI commands for setup
On popular request make the display driver from T20 work on T30 as
well. Turned out to be quite straight forward. However a few notes
about some things encountered during porting: Of course the T30 device
tree was completely missing host1x as well as PWM support but it turns
out this can simply be copied from T20. The only trouble compiling the
Tegra video driver for T30 had to do with some hard-coded PWM pin
muxing for T20 which is quite ugly anyway. On T30 this gets handled by
a board specific complete pin muxing table. The older Chromium U-Boot
2011.06 which to my knowledge was the only prior attempt at enabling a
display driver for T30 for whatever reason got some clocking stuff
mixed up. Turns out at least for a single display controller T20 and
T30 can be clocked quite similar. Enjoy.
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # ASUS TF T30
Tested-by: Jonas Schwöbel <jonasschwoebel@yahoo.de> # Surface RT T30
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # LG P895 T30
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Add board code for R8A779G0 V4H White Hawk board.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Synchronize configuration symbols which are now switched to Kconfig
Mallocate gd->bd->bi_boot_params, i.e. drop the assignment
Sort headers, use clrbits_le32(), use BIT macros where appropriate
Use CONFIG_SYS_CLK_FREQ for counter frequency instead of custom macro]
Add DTs for R8A779G0 V4H White Hawk CPU and BreakOut boards.
Based on Linux next 20230228 DTs up to
commit 058f4df42121 ("Add linux-next specific files for 20230228")
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Tho Vu <tho.vu.wh@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Sync with Linux next 20230228, update commit message
Rename DTs to match Linux, which has dash between white-hawk]
Add R8A779G0 V4H DT extras for U-Boot.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Update compatible string to match latest upstream]
Add initial DT support for R8A779G0 (R-Car V4H). Based on Linux next
commit 058f4df42121 ("Add linux-next specific files for 20230228")
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Phong Hoang <phong.hoang.wz@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Sync with Linux next 20230228, update commit message]
Add board code for R8A779F0 S4 Spider board.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Synchronize configuration symbols which are now switched to Kconfig
Mallocate gd->bd->bi_boot_params, i.e. drop the assignment
Sort headers, use clrbits_le32(), use BIT macros where appropriate
Use CONFIG_SYS_CLK_FREQ for counter frequency instead of custom macro]
Add DTs for R8A779F0 S4 Spider CPU boards and Breakout boards.
Based on Linux next 20230228 DTs up to
commit 058f4df42121 ("Add linux-next specific files for 20230228")
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Sync with Linux next 20230228, update commit message]
Add R8A779F0 S4 DT extras for U-Boot.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Update compatible string to match latest upstream]
Add initial DT for R8A779F0 S4 SoC. Based on Linux next
commit 058f4df42121 ("Add linux-next specific files for 20230228")
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Sync with Linux next 20230228, update commit message]
Tag the serial nodes with bootph-all in order to have these nodes and
the drivers available before relocation.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Sync the serial nodes of the LX2160A based boards with their
representation in Linux. We also imported the clockgen and sysclk nodes
which are dependencies.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Move the serial nodes under the soc node. No changes are made to the
nodes, just their location is changed.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The u-boot dts for these boards do not have an soc node, unlike its
Linux counterpart. This patch just adds the soc node as seen in Linux,
the next patches will move some nodes under it.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Tag the serial nodes with bootph-all in order to have these nodes and
the drivers available before relocation.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Sync the serial nodes of the LS1088A based boards with their
representation in Linux. We also imported the clockgen and sysclk nodes
which are dependencies.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Move the serial nodes under the soc node. No changes are made to the
nodes, just their location is changed.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The u-boot dts for these boards do not have an soc node, unlike its
Linux counterpart. This patch just adds the soc node as seen in Linux,
the next patches will move some nodes under it.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Beacon Embedded has an i.MX8M Plus development kit which consists
of a SOM + baseboard. The SOM includes Bluetooth, WiFi, QSPI, eMMC,
and one Ethernet PHY. The baseboard includes audio, HDMI, USB-C Dual
Role port, USB Hub with five ports, a PCIe slot, and a second Ethernet
PHY. The device trees are already queued for inclusion in Linux 6.3.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add support for Data Modul i.MX8M Plus eDM SBC board. This is an
evaluation board for various custom display units. Currently
supported are serial console, ethernet, eMMC, SD, SPI NOR, USB.
Signed-off-by: Marek Vasut <marex@denx.de>
Add WDT reboot bindings on DH i.MX6 DHSOM to permit the platform
to reboot via WDT in U-Boot. These are custom U-Boot bindings,
hence they are placed in -u-boot.dtsi .
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
J721e SK has been broken since at least March 2022.
The main-navss and mcu-navss nodes were renamed and this caused the
A72 SPL to fail early in the boot even before the serial port was
enabled. Fix this.
A later patch series between v2022.07 and v2022.10 additionally broke
boot on this board by introducing hbmc nodes which are not present on
this board. The right fix is to disable these by default in the SOC
dtsi file, but for now we can also disable them in the u-boot dtsi.
With both these fixed, we can now boot the j721e SK board fully from
mainline u-boot.
Fixes: 58d61fb5a7 ("arm: dts: k3-j721e-sk: Add initial A72 specific dts support")
Fixes: 297daac43a ("arm: dts: k3-j721e-mcu-wakeup: Add HyperBus Controller node")
Reported-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
[gadiyar@ti.com: update commit description]
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Bryan Brattlof <bb@ti.com>
Originally, the mmc aliases node was present in imx6qdl-pico.dtsi.
After the sync with Linux in commit d0399a46e7 ("imx6dl/imx6qdl:
synchronise device trees with linux"), the aliases node is gone as
the upstream version does not have it.
This causes a boot regression in which the eMMC card cannot be found anymore.
Fix it by passing the alias node in the u-boot.dtsi file to
restore the original behaviour where the eMMC (esdhc3) was
mapped to mmc0.
Fixes: d0399a46e7 ("imx6dl/imx6qdl: synchronise device trees with linux")
Signed-off-by: Fabio Estevam <festevam@denx.de>
---------------------------------
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/15819
i.MX patches queued for next:
- Conversions to DM_SERIAL
- Fixes for Toradex boards
- Gateworks Boards
- i.MX8ULP
- EQoS support / fixes, changes in boards
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQS2TmnA27QKhpKSZe309WXkmmjvpgUCZCaU0Q8cc2JhYmljQGRl
bnguZGUACgkQ9PVl5Jpo76YCKgCgk4OueoIggmes+Ccj8bu1BcQbrfYAoJAgMeKE
It0hrVAifD62TPb2rmHt
=hFVG
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-next-20230331' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx into next
u-boot-imx-next-20230331 for next
---------------------------------
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/15819
i.MX patches queued for next:
- Conversions to DM_SERIAL
- Fixes for Toradex boards
- Gateworks Boards
- i.MX8ULP
- EQoS support / fixes, changes in boards
The assigned-clock no longer have to be dropped, the clock are now
defined in clk-imx8mp.c and used by DWMAC driver to configure the
DWMAC clock. Drop the workarounds from U-Boot specific DT extras.
Signed-off-by: Marek Vasut <marex@denx.de>
Add support for DH electronics i.MX8M Plus DHCOM SoM on PDK3 carrier board.
Currently supported are serial console, EQoS and FEC ethernets, eMMC, SD,
SPI NOR and USB 3.0 host.
Signed-off-by: Marek Vasut <marex@denx.de>
The PHY nodes may be activated via DTO in case another SoM variant
is populated into the development kit. Do not delete the nodes.
Signed-off-by: Marek Vasut <marex@denx.de>
The i.MX8MP DHCOM SoM may come with either external RGMII PHY or
LAN8740Ai RMII PHY on the SoM attached to FEC MAC. Add pin mux
settings for both options, so that DT overlay can override these
settings on SoM variant with the LAN8740Ai PHY.
Signed-off-by: Marek Vasut <marex@denx.de>
The i.MX8MP DHCOM SoM may come with either KSZ9131RNXI RGMII PHY
or LAN8740Ai RMII PHY on the SoM attached to EQoS MAC. Add pin
mux settings for both options, so that DT overlay can override
these settings on SoM variant with the LAN8740Ai PHY.
Signed-off-by: Marek Vasut <marex@denx.de>
The current variant of the SoM has LAN8740Ai PHY connected to EQoS
strapped to MDIO address 0 , adjust the MDIO address to match the
hardware.
Signed-off-by: Marek Vasut <marex@denx.de>
A388 Clearfog MMC is either SD Card or eMMC with different behaviour for
both. Setting the device to non-removable in the u-boot.dtsi allows both
to correctly detect the device.
Signed-off-by: Martin Rowe <martin.p.rowe@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Originally, the mmc aliases node was present in imx6qdl-pico.dtsi.
After the sync with Linux in commit d0399a46e7 ("imx6dl/imx6qdl:
synchronise device trees with linux"), the aliases node is gone as
the upstream version does not have it.
This causes a boot regression in which the eMMC card cannot be found anymore.
Fix it by passing the alias node in the u-boot.dtsi file to
restore the original behaviour where the eMMC (esdhc3) was
mapped to mmc0.
Fixes: d0399a46e7 ("imx6dl/imx6qdl: synchronise device trees with linux")
Signed-off-by: Fabio Estevam <festevam@denx.de>
The M.2 slots of the related IOT2050 variant need to be configured
according to the plugged cards. This tries to detect the card using the
M.2 configuration pins of the B-key slot. If that fails, a U-Boot
environment variable can be set to configure manually. This variable is
write-permitted also in secure boot mode as it is not able to undermine
the integrity of the booted system.
The configuration is then applied to mux the serdes and to fix up the
device tree passed to or loaded by the bootloader. The fix-ups are
coming from device tree overlays that are embedded into the firmware
image and there also integrity protected. The OS remains free to load
a device tree to which they do not apply: U-Boot will not fail to boot
in that case.
Based on original patch by Chao Zeng.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Add support for the M.2 board based on the iot2050 advanced board.
The board has two m.2 connectors, one is B-keyed, the other E-keyed.
The B-key slot can connect 5G/SSD devices, and E-key can be used for
WIFI/BT devices.
This variant is covered by PG2 firmware image.
Signed-off-by: chao zeng <chao.zeng@siemens.com>
[Jan: align DT to kernel, polish wording]
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Use external blob otpcmd.bin to replace the 0xff filled OTP programming
command block to create a firmware image that provisions the OTP on
first boot. This otpcmd.bin is generated from the customer keys using
steps described in the meta-iot2050 integration layer for the device.
Based on original patch by Baocheng Su.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Add hashes and configuration signature stubs to prepare verified boot
of main U-Boot by SPL.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The latest version of the binary-only firmware parts come in a combined
form of FSBL and sysfw containers. This implies some layout changes to
the generated firmware image but also makes handling of artifacts much
simpler (4 files less). The env locations will not change, just the
space reserved for U-Boot will shrink from 4 to 3 MB - still plenty of
space left in practice.
Adjust configuration and documentation accordingly.
Along this change, add a new reservation for update commands of the
user-controlled OTP part. A specific userspace tool will fill it, and
the FSBL will evaluate it during boot. This reservation will use 64K of
the former sysfw section.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Refactor according to the entry `fit: Entry containing a FIT` of
document tools/binman/README.entries.
As the generator uses the device tree name for the config description,
board_fit_config_name_match requires a small adjustment as well.
Signed-off-by: Su Baocheng <baocheng.su@siemens.com>
[Jan: re-add now required CONFIG_OF_LIST, update config matching]
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Due to different signature keys, the PG1 and the PG2 boards can no
longer use the same FSBL (tiboot3). This makes it impossible anyway to
maintaine a single flash.bin for both variants, so we can also split the
build.
A new target is added to indicates the build is for PG1 vs. PG2 boards.
Hence now the variants have separated defconfig files.
The runtime board_is_sr1() check does make no sense anymore, so remove
it and replace with build time check.
Documentation is updated accordingly. New binary artifacts are already
available via meta-iot2050.
Signed-off-by: Su Baocheng <baocheng.su@siemens.com>
[Jan: refactor config option into targets, tweak some wordings]
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
After the conversion to DM_SERIAL in commit 01f372d8d6 ("udoo_neo:
Select DM_SERIAL and drop iomux board level init") the SPL log is gone
and the U-Boot proper log becomes incomplete:
Core: 80 devices, 18 uclasses, devicetree: separate
MMC: FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... OK
In: serial@2020000
Out: serial@2020000
Err: serial@2020000
Net: eth0: ethernet@2188000
Hit any key to stop autoboot: 0
Introduce the u-boot.dtsi file that passes the u-boot,dm-pre-reloc
properties to the relevant nodes so that UART can be used early in SPL.
With this change, the complete SPL and U-Boot messages are seen again.
Signed-off-by: Fabio Estevam <festevam@denx.de>
While this change is correct for v2023.04 it is not correct for next
(where this is right now) nor post-v2023.04.
This reverts commit 8653e5d3b7.
Signed-off-by: Tom Rini <trini@konsulko.com>
The Rockchip timer driver has been renamed after the fall back compatible.
There's no need to replace the timer compatible in rk3188-radxarock-u-boot.dtsi
anymore, so remove.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Running U-Boot from eMMC on a ROCK 3 Model A result in the following:
U-Boot SPL 2023.04-rc3 (Mar 11 2023 - 17:24:48 +0000)
Trying to boot from MMC1
Card did not respond to voltage select! : -110
spl: mmc init failed with error: -95
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###
The sdhci node is missing in board device tree, sync device tree from
linux v6.3-rc1 to fix booting from eMMC. Also disable sdmmc2 and uart1
nodes related to using a WiFi and BT module in the M2 slot.
Fixes: b44c54f600 ("arm64: dts: rockchip: rk3568: Add Radxa ROCK 3 Model A board support")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The boot source node path for emmc is using the old sdhci name.
Replace with correct mmc name and also add same-as-spl to boot order.
Fixes: 0d61f8e5f1 ("rockchip: rk3568: add boot device detection")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Running U-Boot on a ROCK 3 Model A result in the following:
No serial driver found
resetting ...
no sysreset
### ERROR ### Please RESET the board ###
Replace bootph- props with u-boot,dm- props to fix this.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Per Andre:
[T]hese two patches containing just devicetree updates for
Allwinner boards.
I was still hoping for a review, since we cannot import the files from
the Linux tree verbatim, but managed to write some filter script that
convinced me that the changes are fine.
The files are from Linux v6.2-rc2, but are identical to the v6.2
release.
Tag the serial nodes with bootph-all in order to have these nodes and
the drivers available before relocation.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Sync the serial nodes of the LS208XA RDB/QDS boards with their
representation in Linux. We also imported the clockgen and sysclk nodes
which are dependencies.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Move the serial nodes under the soc node. No changes are made to the
nodes, just their location is changed.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The u-boot dts for these boards do not have an soc node, unlike its
Linux counterpart. This patch just adds the soc node as seen in Linux,
the next patches will move some nodes under it.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When the first device tree description was added for the ethernet nodes,
the 2 10G ports on the LS1088ARDB were wrongly described as 'xgmii'.
Fix this by replacing the two last occurrences of 'xgmii' in the device
trees of the Layerscape DPAA2 devices.
Fixes: 68c7c008e8 ("arm: dts: ls1088ardb: add DPMAC and PHY nodes")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The Odroid Go Ultra has 2 chained PMICs RK818 and RK818, and needs
an adjustment on the BUCK and LDO values.
Add the initial regulators values in -u-boot.dtsi & run the initial
regulator setup in a new odroid-go-ultra board.
Proper OTG and BOOST regulators are still missing to have USB-A
host properly working.
Link: https://lore.kernel.org/r/20230210-u-boot-odroid-go-ultra-pmics-setup-v1-1-1f16d62b76af@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Enable support for sysinfo on R-Car D3 Draak board. The sysinfo is used
e.g. to access and decode board-specific information and then in turn
used by board-info to print those information.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Tam Nguyen <tam.nguyen.xa@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Drop compatible from I2C node, this is in r8a77995.dtsi already.
Drop status = "okay" from EEPROM node.
Add dts: tag.
Fix Kconfig EEPROM address to be 0x50 and match the DT, sync config.]
Add new sysinfo IDs for R-Car V3H Condor/Condor-I .
Enable support for sysinfo on R-Car V3H Condor/Condor-I. The sysinfo is
used e.g. to access and decode board-specific information and then in
turn used by board-info to print those information.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Tam Nguyen <tam.nguyen.xa@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Drop compatible from I2C node, this is in r8a77980.dtsi already.
Drop status = "okay" from EEPROM node.
Add dts: tag.
Update the commit message, note the new sysinfo IDs.
Fix Kconfig EEPROM address to be 0x50 and match the DT, sync config.]
By default enable nand-on-flash-bbt DT flag, so that driver always refers
to the bad block table(bbt) present on the flash device.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230224050709.30014-5-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
DC3 nand node is not correct, it is showing all partitions under
controller node directly. Create two sub nand nodes with partitions for
each.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230224050709.30014-4-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
The latest SOM specification doesn't enforce certain MIO lines allocated
for ethernet or ethernet controller itself. That's why remove comment about
it which is likely there from early version of specification.
Also removed the same comment from pinctrl node. It is clear that it has to
be defined for different carrier cards.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/9406377bf2c391ac0200670511bd6b0edb097c96.1676880543.git.michal.simek@amd.com
Since the zynqmp boards can run upstream OP-TEE, and having the DT node
present doesn't cause any side effects add it in case someone tries to
load OP-TEE.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Link: https://lore.kernel.org/r/20230216133921.866786-1-ilias.apalodimas@linaro.org
Signed-off-by: Michal Simek <michal.simek@amd.com>
The pl330 DMA controller provides number of DMA channels and requests
through its registers, so duplicating this information (with a chance of
mistakes) in DTS is pointless. Additionally the DTS used always wrong
property names which causes DT schema check failures - the bindings
documented 'dma-channels' and 'dma-requests' properties without leading
hash sign.
Reported-by: Rob Herring <robh@kernel.org>
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20220430121902.59895-2-krzysztof.kozlowski@linaro.org
Since we need to support legacy phys with the dwc3 controller,
we enable this quirk on the zynqmp platforms.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20221023215649.221726-1-m.grzeschik@pengutronix.de
Signed-off-by: Michal Simek <michal.simek@amd.com>
The node names should be generic and DT schema expects certain pattern:
xilinx/zynqmp-zcu100-revC.dtb: leds: 'vbus-det' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20221125144136.477171-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Michal Simek <michal.simek@amd.com>
cdns prefix was deprecated and replaced by xlnx one in upstream Linux. Also
U-Boot driver has been updated to support new compatible string that's why
it is time to remove it and deprecate it.
Signed-off-by: Michal Simek <michal.simek@amd.com>
AM62A7-SK board has 4GB LPDDR4 Micron MT53E2G32D4DE-046 AUT:B part
but only 2GB was enabled early.
Enable full 4GB memory by updating the latter 2GB memory region
which gets mapped to 0x0880000000 i.e. DDR16SS0_SDRAM as referred in
Table 2-1. AM62A Common SoC Memory of AM62Ax TRM [1].
[1] : https://www.ti.com/lit/zip/spruj16
Logs: https://gist.github.com/devarsht/e85b6af89c01ddadb3a62f3e5f196af8
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Synchronize devicetree sources with Linux v6.2.
- Use GIC interrupt definitions
- Add reg properties in USB-glue and SoC-glue node
- Fix node names to follow the generic names list in DT specification
- Add L2 cache and AHCI nodes
- Update nand and pcie nodes
- And some trivial fixes
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Acked-by: Marek Vasut <marex@denx.de>
UniPhier DT applies its own USB node for U-Boot due to the USB driver
constrains. After solving this issue, u-boot allows the original USB node.
After switching USB node, synchronization of USB node with Linux becomes
possible.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Acked-by: Marek Vasut <marex@denx.de>
Sync the devicetree files from the Linux kernel repo, v6.2-rc2.
This is covering the 64-bit SoCs, from arch/arm64/boot/dts/allwinner.
This enables GPU power management in the kernel for the H6, enables
Bluetooth on the Pinebook, and adds USB to the H616 devices (just
for newer Linux kernels at the moment, U-Boot support is pending).
As before, this omits the non-backwards compatible changes to the R_INTC
controller, to remain compatible with older kernels.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Sync the devicetree files from the Linux kernel repo, v6.2-rc2.
This is covering the 32-bit SoCs, from arch/arm/boot/dts.
This enables some new devices for the F1C100s family, though this is of
little relevance to U-Boot itself.
The H3 gains the "phys" property for the first USB controller, which
prevents an error message when U-Boot's USB stack comes up, and allows
using this port in host mode.
As before, this omits the non-backwards compatible changes to the R_INTC
controller, to remain compatible with older kernels.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmP+97wcHGV1Z2VuLmhy
aXN0ZXZAY29sbGFib3JhLmNvbQAKCRAesx4CDqwvyExpB/wLQVjeBM+sEcABzT52
c7qtAvtgl/UbPedYyMz2YorL5BcHsdmBbGfSzBISEc8kLdtAVMTKAaqvN7msaJFX
MwPIZAXWd8cPM0EA7wSyjYDGOvcEzGWF7oxSbeq+j7M2kibvsQLGW7iaY5cjFIzx
QPQ19T2tyX3jrsy8dxCsPivB70vB/3lqiEmCZX2UddsjxrL6Vt2H3k6O+/Ler5wS
/nJIzKLDPc+aDZSv+aevDlJZi1eGkpTHldNaHXqdYILzvnXIQmA6kP0mWPZ9g6wZ
s6ed1N5VeiS4j6oH5Woj3nDKny7P3AKSd9+c/eXfbtdia2D0yBHtiHQauIwNPCd3
wAcH
=/Vn2
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-fixes-2023.04-a' of https://source.denx.de/u-boot/custodians/u-boot-at91
First set of u-boot-at91 fixes for the 2023.04 cycle:
This fixes set include one clock index fix for sama7g5 and two board
configuration alignments for pm9g45.
ROCK 5B is a Rockchip RK3588 based SBC (Single Board Computer) by Radxa.
There are tree variants depending on the DRAM size : 4G, 8G and 16G.
Specification:
Rockchip Rk3588 SoC
4x ARM Cortex-A76, 4x ARM Cortex-A55
4/8/16GB memory LPDDR4x
Mali G610MC4 GPU
MIPI CSI 2 multiple lanes connector
eMMC module connector
uSD slot (up to 128GB)
2x USB 2.0, 2x USB 3.0
2x HDMI output, 1x HDMI input
Ethernet port
40-pin IO header including UART, SPI, I2C and 5V DC power in
USB PD over USB Type-C
Size: 85mm x 54mm
Kernel commits:
a1d3281450ab ("arm64: dts: rockchip: Add rock-5b board")
6fb13f888f2a ("arm64: dts: rockchip: Update sdhci alias for rock-5b")
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The cpuid on RK3568 is located at 0xa instead of 0x7 as all other SoCs.
Add and use a CFG_CPUID_OFFSET to define this offset.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Neural Compute Module 6(Neu2) is a 96boards SoM-CB compute module
based on Rockchip RK3588 from Edgeble AI.
General features:
- Rockchip RK3588
- up to 32GB LPDDR4x
- up to 128GB eMMC
- 2x MIPI CSI2 FPC
On module WiFi6/BT5 is available in the following Neu6 variants.
Neural Compute Module 6(Neu6) IO board is an industrial form factor
ready-to-use IO board from Edgeble AI.
IO board offers plenty of peripherals and connectivity options and
this patch enables basic eMMC and UART which is enough to successfully
boot Linux.
Neu6 needs to mount on top of this IO board in order to create a
complete Edgeble Neural Compute Module 6(Neu6) IO platform.
Boot log for the record,
DDR Version V1.08 20220617
LPDDR4X, 2112MHz
channel[0] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[1] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[2] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[3] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
Manufacturer ID:0x6
CH0 RX Vref:31.7%, TX Vref:21.8%,21.8%
CH1 RX Vref:30.7%, TX Vref:22.8%,23.8%
CH2 RX Vref:30.7%, TX Vref:22.8%,22.8%
CH3 RX Vref:30.7%, TX Vref:21.8%,21.8%
change to F1: 528MHz
change to F2: 1068MHz
change to F3: 1560MHz
change to F0: 2112MHz
out
U-Boot SPL 2023.01-00952-g1d1785a516-dirty (Jan 30 2023 - 19:53:55 +0530)
Trying to boot from MMC1
INFO: Preloader serial: 2
NOTICE: BL31: v2.3():v2.3-391-g856309329:derrick.huang
NOTICE: BL31: Built : 14:15:50, Jul 18 2022
INFO: ext 32k is not valid
INFO: GICv3 without legacy support detected.
INFO: ARM GICv3 driver initialized in EL3
INFO: system boots from cpu-hwid-0
INFO: idle_st=0x21fff, pd_st=0x11fff9, repair_st=0xfff70001
INFO: dfs DDR fsp_params[0].freq_mhz= 2112MHz
INFO: dfs DDR fsp_params[1].freq_mhz= 528MHz
INFO: dfs DDR fsp_params[2].freq_mhz= 1068MHz
INFO: dfs DDR fsp_params[3].freq_mhz= 1560MHz
INFO: BL31: Initialising Exception Handling Framework
INFO: BL31: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader, Booting device without OPTEE initialization. SMC`s destined for OPTEE will return SMC_UNK
ERROR: Error initializing runtime service opteed_fast
INFO: BL31: Preparing for EL3 exit to normal world
INFO: Entry point address = 0xa00000
INFO: SPSR = 0x3c9
U-Boot 2023.01-00952-g1d1785a516-dirty (Jan 30 2023 - 19:53:55 +0530)
Model: Edgeble Neu6A IO Board
DRAM: 7.5 GiB (effective 3.7 GiB)
Core: 71 devices, 15 uclasses, devicetree: separate
MMC: mmc@fe2c0000: 0
Loading Environment from nowhere... OK
In: serial@feb50000
Out: serial@feb50000
Err: serial@feb50000
Model: Edgeble Neu6A IO Board
Net: No ethernet found.
Hit any key to stop autoboot: 0
=>
Add support for Edgeble Neu6 Model A IO Board.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Booting from SDMMC is one of the fast and easy booting methods
for initial support of any SoC to upstream more features.
This patch is trying to add the sdmmc node for rk3588 and added
as u-boot specific node in -u-boot.dtsi as upstream Linux is not
supporting yet.
As soon as Linux supports it, a sync of the Linux device tree
would eventually drop this node.
Clock properties as added according to the rockchip mmc driver
but the actual definition might add scmi clocks into 0 and 1
indexes. This is due to scmi clock are not supporting in upstream
U-Boot. Properly addition of scmi clock would eventually follow
sdmmc clock definition of Linux once they upstreamed.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Add u-boot,dm-spl and u-boot,dm-pre-reloc related properties
for Rockchip RK3588 SoC to boot the SPL.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Neural Compute Module 6(Neu6) IO board is an industrial form factor
ready-to-use IO board from Edgeble AI.
IO board offers plenty of peripherals and connectivity options and
this patch enables basic eMMC and UART which is enough to successfully
boot Linux.
Neu6 needs to mount on top of this IO board in order to create a
complete Edgeble Neural Compute Module 6(Neu6) IO platform.
commit <a5079a534554> ("arm64: dts: rockchip: rk3588: Add Edgeble Neu6
Model A IO")
Add support for Edgeble Neu6 Model A IO Board.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Neural Compute Module 6(Neu2) is a 96boards SoM-CB compute module
based on Rockchip RK3588 from Edgeble AI.
General features:
- Rockchip RK3588
- up to 32GB LPDDR4x
- up to 128GB eMMC
- 2x MIPI CSI2 FPC
On module WiFi6/BT5 is available in the following Neu6 variants.
Neu6 needs to mount on top of associated Edgeble IO boards for
creating complete platform solutions.
Enable eMMC for now to boot Linux successfully.
commit <3d9a2f7e7c5e> ("arm64: dts: rockchip: rk3588: Add Edgeble Neu6
Model A SoM")
Add support for Edgeble Neu6 Model A SoM.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This initial version supports CPU, dma, interrupts, timers, UART and
SDHCI (everything necessary to boot Linux on this system on chip) as
well as Ethernet, I2C, PWM and SPI.
The DT is split into rk3588 and rk3588s, which is a reduced version
(i.e. with less peripherals) of the former.
commit <9fb232e9911f> (" arm64: dts: rockchip: Add base DT for rk3588
SoC")
commit <d68a97d501f8> ("arm64: dts: rockchip: Add rk3588 pinctrl data")
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add gpio-ranges property to GPIO nodes so that the bank ID can
be correctly derived for each GPIO bank.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync rk3566 and rk3568 from the mainline Linux kernel (6.2-rc2 as of
this writing).
Note that this will rename the rk3568-evb to rk3568-evb1-v10.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add the gpio-ranges property to each GPIO node for use in deriving
the correct bank ID. Note that invoking "gpio status -a" no longer
causes the board to hit a "Synchronous Abort".
Fixes: 537b1a2774 ("rockchip: add px30 devicetrees")
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
combphy1 is failing to probe due to unhandled assigned-clocks and
assigned-clocks-rates.
=> usb start
starting USB...
Bus usb@fd000000: Failed to get PHY1 for usb@fd000000
Port not available.
Bus usb@fd800000: USB EHCI 1.00
There is no real requirement for them in U-Boot to handle, hence
mark them as deleted-properties for the probe to success
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Radxa Compute Module 3(CM3) IO board an application board from Radxa
and is compatible with Raspberry Pi CM4 IO form factor.
Radxa CM3 needs to mount on top of this IO board in order to create
complete Radxa CM3 IO board platform.
Add support for Radxa CM3 IO Board defconfig and -u-boot.dtsi
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Radxa Compute Module 3(CM3) IO board an application board from Radxa
and is compatible with Raspberry Pi CM4 IO form factor.
Specification:
- 1x HDMI,
- 2x MIPI DSI
- 2x MIPI CSI2
- 1x eDP
- 1x PCIe card
- 2x SATA
- 2x USB 2.0 Host
- 1x USB 3.0
- 1x USB 2.0 OTG
- Phone jack
- microSD slot
- 40-pin GPIO expansion header
- 12V DC
Radxa CM3 needs to mount on top of this IO board in order to create
complete Radxa CM3 IO board platform.
linux-next commit for the same,
commit <8f19828844f2> ("arm64: dts: rockchip: Fix compatible for Radxa
CM3")
Add support for Radxa CM3 IO Board.
Co-developed-by: FUKAUMI Naoki <naoki@radxa.com>
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Co-developed-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Radxa Compute Module 3(CM3) is one of the modules from a series
System On Module based on the Radxa ROCK 3 series and is compatible
with Raspberry Pi CM4 pinout and form factor.
Specification:
- Rockchip RK3566
- up to 8GB LPDDR4
- up to 128GB high performance eMMC
- Optional wireless LAN, 2.4GHz and 5.0GHz IEEE 802.11b/g/n/ac wireless,
BT 5.0, BLE with onboard and external antenna.
- Gigabit Ethernet PHY
Radxa CM3 needs to mount on top of this IO board in order to create
complete Radxa CM3 IO board platform.
Since Radxa CM3 is compatible with Raspberry Pi CM4 pinout so it is
possible to mount Radxa CM3 on top of the Rasberry Pi CM4 IO board.
linux-next commit for the same,
commit <8f19828844f2> ("arm64: dts: rockchip: Fix compatible for Radxa
CM3")
Add support for Radxa CM3.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Co-developed-by: FUKAUMI Naoki <naoki@radxa.com>
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add Radxa ROCK 3 Model A support. sync rk3308-rock-pi-s.dts from
Linux 6.2.0-rc7.
ROCK Pi S is RK3308 based SBC from radxa.com. ROCK Pi S has a,
- 256MB/512MB DDR3 RAM
- SD, NAND flash (optional on board 1/2/4/8Gb)
- 100MB ethernet, PoE (optional)
- Onboard 802.11 b/g/n wifi + Bluetooth 4.0 Module
- USB2.0 Type-A HOST x1
- USB3.0 Type-C OTG x1
- 26-pin expansion header
- USB Type-C DC 5V Power Supply
Linux commit commit for the same,
<2e04c25b1320> ("arm64: dts: rockchip: add ROCK Pi S DTS support")
Signed-off-by: Akash Gajjar <gajjar04akash@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add Radxa ROCK 3 Model A support. sync rk3568-rock-3a.dts from Linux 6.2.0-rc7
Board Specifications
- Rockchip RK3568
- 2/4/8GB LPDDR4 3200MT/s
- eMMC socket, SD card slot
- GbE LAN
- PCIe 3.0/2.0
- M.2 Connector
- 3.5mm Audio jack with mic
- HDMI 2.0, MIPI DSI/CSI
- USB 3.0 Host/OTG, USB 2.0 Host
- 40-pin GPIO expansion ports
- USB Type C PD 2.0, 9V/2A, 12V/2A, 15V/2A, 20V/2A
Refer Linux commit <22a442e6586c>
("arm64: dts: rockchip: add basic dts for the radxa rock3 model a")
Signed-off-by: Akash Gajjar <gajjar04akash@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Rockchip SoCs typically use U-Boot TPL to initialize DRAM, then jumps
back to BootRom to load next stage, U-Boot SPL, into DRAM. BootRom then
jumps to U-Boot SPL to continue the normal boot flow.
However, there is no support to initialize DRAM on RK35xx SoCs using
U-Boot TPL and instead an external TPL binary must be used to generate a
bootable u-boot-rockchip.bin image.
Add CONFIG_ROCKCHIP_EXTERNAL_TPL to indicate that an external TPL should
be used. Build U-Boot with ROCKCHIP_TPL=/path/to/ddr.bin to generate a
bootable u-boot-rockchip.bin image for RK3568.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Eugen Hristev <eugen.hristev@collabora.com>
The rk3328 sdram driver read sdram parameters from the devicetree into a
struct rk3328_sdram_params using dev_read_u32_array.
After commit 5ab30c3176 ("ram: rockchip: Update ddr pctl regs for px30")
changed the size of struct ddr_pctl_regs, a member of struct
rk3328_sdram_params, U-Boot TPL can no longer initialize DRAM on RK3328.
Add ten u32 to the sdram parameter array in devicetree to align with
this size change. This fixes DRAM initialization on RK3328.
Fixes: 5ab30c3176 ("ram: rockchip: Update ddr pctl regs for px30")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # roc-rk3328-cc
Provide human-readable manufacturer and product names for the
FriendlyELEC NanoPi R4S.
Enable CONFIG_SYSINFO and CONFIG_SYSINFO_SMBIOS by default.
Signed-off-by: Christian Kohlschütter <christian@kohlschutter.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The PMC_MCK1 clock id for the ebi node is 23.
Fixes: 746b738224 ("ARM: dts: at91: sama7g5/sama7g5ek: align with Linux DT")
Reviewed-by: Eugen Hristev <eugen.hristev@collabora.com>
Signed-off-by: Mihai Sain <mihai.sain@microchip.com>
Default parent clock for the PWM on Tegra is a 32kHz clock and
is unable to support the requested PWM period.
Fix PWM support on Tegra20, Tegra30, Tegra114, Tegra124 and Tegra210 by
updating the parent clock for the PWM to be the PLL_P.
This commit is equivalent to Linux kernel commit:
https://lore.kernel.org/all/20221010100046.6477-1-jonathanh@nvidia.com/
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # ASUS TF T30
Tested-by: Robert Eckelmann <longnoserob@gmail.com> # ASUS TF101 T20
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # ASUS TF201 T30
Tested-by: Thierry Reding <treding@nvidia.com> # T30 and T124
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Tom <twarren@nvidia.com>
Add devicetree for chameleonv3 with the 270-2I2-D11E variant of the
Mercury+ AA1 module
Signed-off-by: Paweł Anikiel <pan@semihalf.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This file is included by the different chameleonv3 variants. Change the
name to .dtsi.
Signed-off-by: Paweł Anikiel <pan@semihalf.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Set the bitstream name per Chameleon variant. This allows the same
boot filesystem with all bitstream variants to be used on different
boards.
Signed-off-by: Paweł Anikiel <pan@semihalf.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
i2c updates for v2023.04
- add new i2c driver ast2600 from Ryan Chen
- i2c-cdns: make read fifo-depth configurable through device tree
from Pei Yue Ho
- mxc i2c driver: print base address in hex, not in decimal
from Fabio
When DM_SERIAL is enabled, the device-tree tag u-boot,dm-pre-reloc is
required for this board to boot over UART with kwboot. Enable this in
kirkwood-pogoplug-series-4-u-boot.dtsi.
Added by Stefan while applying:
Please note that it's not fully understood, why this property really
is needed. Here a link to the discussion about this:
https://lore.kernel.org/r/20230201080210.ypz4nrj4y2igwxz3@pali/
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Synology DS116 is a NAS based on Marvell Armada 385 SoC.
Board Specification:
- Marvel MV88F6820 Dual Core at 1.8GHz
- 1 GiB DDR3 RAM
- 8MB Macronix mx25l6405d SPI flash
- I2C
- 2x USB 3.0
- 1x GBE LAN port (PHY: Marvell 88E1510)
- 1x SATA (6 Gbps)
- 3x LED
- PIC16F1829 (connected to uart1)
- GPIO fan
- serial console
Note that this patch depends on the add-support for Thecus N2350 patch:
https://patchwork.ozlabs.org/project/uboot/patch/20230201231306.7010-1-mibodhi@gmail.com/
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
The i2c driver have global register that i2c bus use
ofnode_get_parent to get parent register address.
Signed-off-by: Ryan Chen <ryan_chen@aspeedtech.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Previously, the TX LED would flash but nothing would appear on the
serial port, and the board would appear dead with a build of the
socfpga_cyclone5_defconfig. I have verified that adding the frequency to
the uart will fix the serial console on my board.
Thanks to @ehoffman on the Rocketboards forum:
https://forum.rocketboards.org/t/cyclonev-programming-fpga-from-u-boot/2230/30
Signed-off-by: Jade Lovelace <lists@jade.fyi>
Reviewed-by: Marek Vasut <marex@denx.de>
Use standard pinconf drive-strength values from Linux DT bindings rather
than ones based on custom u-boot header. These changes are in direction
to make u-boot DTs for Qcom SoCs to be compatible with standard Linux
DT bindings.
Also, add support for pinconf bias-pull-up.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
As MDIO driver does not support Driver Model, the
pinctrl settings in the MDIO node will not
be applied resulting in PHY not being detected.
To workaround this we add the MDIO pinctrl in
the CPSW3G node in the -u-boot.dtsi file.
Add the missing MDIO and RGMII pinctrl nodes in
k3-am642-r5-evm.dts
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add MV88E61XX DSA support:
- update dt to provide internal MDIO bus and port handles.
U-Boot requires a more restrictive subset of the dt bindings
required by Linux for the sake of simplifying code
- update defconfig to remove old driver and enable new one
- replace mv88e61xx_hw_reset weak override with board_phy_config support
for register configuration that is outside the scope of the DSA driver
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Synchronize R-Car device trees with Linux 6.1.7,
commit 21e996306a6afaae88295858de0ffb8955173a15 .
The following script has been used for the synchronization:
$ for i in $(cd arch/arm/dts/ ; ls -1 r8a* | grep -v 'u-boot.dts' ; sed -n '/#include/ s@.*"\(.*\)"@\1@p' $(ls -1 r8a* | grep -v 'u-boot.dts')) ; do
if [ -e /linux-2.6/arch/arm64/boot/dts/renesas/$i ] ; then
cp /linux-2.6/arch/arm64/boot/dts/renesas/$i arch/arm/dts/ ;
elif [ -e /linux-2.6/arch/arm/boot/dts/$i ] ; then
cp /linux-2.6/arch/arm/boot/dts/$i arch/arm/dts/
else
echo "NOT FOUND: $i"
fi
done
$ git add $( ( cd arch/arm/dts/ ; ls -1 r8a* | grep -v 'u-boot.dts' ; sed -n '/#include/ s@.*"\(.*\)"@\1@p' $(ls -1 r8a* | grep -v 'u-boot.dts')) | tr " " "\n" | sed 's@^@arch/arm/dts/@g' )
Move the include/dt-bindings/{clk,clock}/versaclock.h header used by
the renesas boards to match Linux 6.1.y as well.
Keep arch/arm/dts/r8a774c0-u-boot.dtsi sdhi3 node as it is now used
by the arch/arm/dts/r8a774c0-cat874.dts board.
Pick s@spi-flash@flash@ change in arch/arm/dts/r8a779a0-falcon-u-boot.dts
from "ARM: dts: Synchronize R-Car V3U DTs with Linux 5.18.3" .
Adjust R8A77990 Ebisu CONFIG_SYS_MMC_ENV_DEV from 2 to 0 to reflect
the card enumeration in ebisu.dtsi /aliases DT node .
Adjust R8A7795 and R8A7796 ULCB CONFIG_SYS_MMC_ENV_DEV from 1 to 0 to
reflect the card enumeration in ulcb.dtsi /aliases DT node .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Tam Nguyen <tam.nguyen.xa@renesas.com> # r8a779a0-falcon-u-boot.dts
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com> # r8a779a0-falcon-u-boot.dts
NXP tested imx8mn-ddr4 with firmware version 201810 only. Use this
version for all imx8mn targets with DRAM DDR4.
Fixes: 93c4c0e4dd ("arm: dts: imx8mn-u-boot: Create common imx8mn-u-boot.dtsi")
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Reviewed-by: Fabio Estevam <festevam@denx.de>
In some situations the GSC firmware where the EEPROM containing the
model and DRAM configuration may not be ready by the time the SoC
is ready to talk to it over I2C.
Instead of a hard delay, poll the I2C lines to wait until they are
released to avoid the I2C drivers 'Arbitation lost' error message.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Add I2C GPIO bus recovery support by adding scl-gpios and sda-gpios for the
various I2C busses on Gateworks Venice boards.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Synchronizing the device tree with linux introduced a regression.
The U-Boot specific dtsi mustn't override the alias settings for
the eMMC/SD interfaces.
Without this U-Boot cannot access the eMMC and boot the kernel.
Fixes: c21b61bff1 ("colibri-imx6ull/-emmc: synchronise device tree with linux")
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
In case U-Boot itself if the PSCI provider on i.MX8M, do not
require the ATF BL31 blob, as at that point the blob is useless
and would interfere with U-Boot operation.
Signed-off-by: Marek Vasut <marex@denx.de>
In commit d0399a46e7, the device tree was
synchronized from linux and the aliases were dropped.
They need to be kept so that the mmc cards are in the right order.
Without the aliases, u-boot reports:
MMC: FSL_SDHC: 2, FSL_SDHC: 3
With the aliases, u-boot reports:
MMC: FSL_SDHC: 0, FSL_SDHC: 1
The upstream linux device tree does not contain the same aliases than
u-boot (It keeps the devices order with /dev/mmcblk2 and /dev/mmcblk3).
Because this board has been using different aliases in u-boot
and linux, a imx6q-sabrelite-u-boot.dtsi file is added to be
automatically included in imx6q-sabrelite.dts.
This way, linux and u-boot each keep their own aliases and there
is no breakage on current installations.
This should never be done for new boards as we want to keep linux and
u-boot with the same aliases as much as possible.
This patch is only necessary to avoid breaking existing setups.
Signed-off-by: Detlev Casanova <detlev.casanova@collabora.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The property fsl,mux_mask is deleted by commit ed7bda5 (imx8ulp:
synchronise device tree with linux). This causes the pinctrl
driver not work on 8ULP, so fail to print any log.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
The changes of commit 6a21c69521 ("arm: dts: imx8mp: add of-list
support to common imx8mp-u-boot.dtsi") breaks the loading of the fip.
This commit fixes the break by modify the configuration properly.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
assign a label for config-SEQ so that the board dts can modify
the configuration more easily.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Add the board support for the i.MX8MM Cloos PHG board.
This board uses a imx8mm-tqma8mqml SoM from TQ-Group.
imx8mm-phg.dts and imx8mm-tqma8mqml.dtsi are taken
directly from Linux 6.2-rc3.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add aliases for the RTCs on the board and on the SoC. This ensures that
the primary RTC is always the one on the board that has a buffered supply
and maximum accuracy.
This is a direct port of the pending commit from linux-next.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Originally, the mmc aliases node was present in imx6qdl-sabresd.dtsi.
After the sync with Linux in commit d0399a46e7 ("imx6dl/imx6qdl:
synchronise device trees with linux"), the aliases node is gone as
the upstream version does not have it.
This causes a regression in which the SD card cannot be found anymore.
Fix it by passing the alias node in the u-boot.dtsi file to
restore the original behaviour where the SD card (esdhc3) was
mapped to mmc1.
Fixes: d0399a46e7 ("imx6dl/imx6qdl: synchronise device trees with linux")
Reported-by: Carlos Rafael Giani <dv@pseudoterminal.org>
Signed-off-by: Fabio Estevam <festevam@denx.de>
This reverts commit f5315dd629.
[why]
TPL is not mandatory for not all Rockchip SoCs, some SoCs like
RK356x, and RK3588 still use mainline u-boot without TPL as
their ddr init programs are accessed via binaries provided by
Rockchip instead of ddr source code.
Marking TPL build makes it not able to build u-boot.itb on
RK356x targets so revert this so that it can build an SPL build
that would support all across Rockchip platforms.
Suggested-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Tested-by: Anand Moon <linux.amoon@gmail.com> # CM3
Add pinctrl's for high speed eMMC and MMC cards.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
In case the CONFIG_IMX8M_LPDDR4 and CONFIG_IMX8M_DDR4 options are both
disabled (i. e. BSH boards), binmain fails because DDR4 bin files are
missing.
Fixes: 93c4c0e4dd ("arm: dts: imx8mn-u-boot: Create common imx8mn-u-boot.dtsi")
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
ODROID-N2L is a variant SBC in small form factor and some peripherals
are removed from ODROID-N2PLUS based on S922X SoC.
- On-board ethernet is removed
- On-board RTC is removed
- USB 3.0 hub is removed, so one USB 2.0 and one USB 3.0 host ports
are available
- Huge heatsink is replaced with 40x40mm heatsink, 5V active heatsink
is recommended or a tall passive sink is optional
- 3.5mm earjack is removed
- IR remote receiver is removed
- MIPI DSI port is added
It doesn't use the odroid-n2 board support since ADC revision
collides with Odroid-N2+ and since it doesn't have on-board ethernet
no need to load the MAC address from eFuses.
Link: https://lore.kernel.org/r/20230126-u-boot-odroid-n2l-v1-2-c60f695e0f6c@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
The SK architecture comprises of baseboard and a SOM board. The
AM68 Starter Kit's baseboard contains most of the actual connectors,
power supply etc. The System on Module (SoM) is plugged on to the base
board. Therefore, add support for peripherals brought out in the base
board.
Schematics: https://www.ti.com/lit/zip/SPRR463
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
AM68 Starter Kit (SK) is a low cost, small form factor board designed
for TI’s AM68 SoC. TI’s AM68 SoC comprises of dual core A72, high
performance vision accelerators, hardware accelerators, latest C71x
DSP, high bandwidth real-time IPs for capture and display. The SoC is
power optimized to provide best in class performance for industrial
applications.
AM68 SK supports the following interfaces:
* 16 GB LPDDR4 RAM
* x1 Gigabit Ethernet interface
* x1 USB 3.1 Type-C port
* x2 USB 3.1 Type-A ports
* x1 PCIe M.2 M Key
* 512 Mbit OSPI flash
* x2 CSI2 Camera interface (RPi and TI Camera connector)
* 40-pin Raspberry Pi GPIO header
SK's System on Module (SoM) contains the SoC, PMIC, DDR and OSPI flash.
Therefore, add support for the components present on the SoM.
Schematics: https://www.ti.com/lit/zip/SPRR463
TRM: http://www.ti.com/lit/pdf/spruj28
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
makefile:
- Add multi_dtb_fit dependency
clk:
- Handle error cases
microblaze:
- Disable falcon mode and cleanup code around
xilinx:
- Enable regular expression matching in board_fit_config_name_match()
- Fix FRU handling for 0xC1 format
- Fix Xilinx legacy format eeprom parsing
zynqmp:
- Some DT updates/cleanups
- Fix IDcode for xck24
- Remove empty mini config files
- Add support for k24
versal:
- Remove empty mini config files
versal_net:
- Setup timer when runs in EL3
- Build u-boot.elf for mini configurations
zynq-gem:
- Add support for new compatible strings
- Remove support for Avnet Ultrazedev SOM
- Handle SGMII with PCS phy
spi:
- Add support for gigadevice parts
misc:
- Remove CONFIG_TARGET_VENUS ifdef
- Add missing headers to remove sparse warnings
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCY9PmzwAKCRDKSWXLKUoM
IYWxAJwNgiXtFT17pBy+1M0JvSWgyvWF3QCfTQG2Krnw0+d65PF5A7UFTDL7SZM=
=cMrc
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2023.04-rc1' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx chnages for v2023.04-rc1
makefile:
- Add multi_dtb_fit dependency
clk:
- Handle error cases
microblaze:
- Disable falcon mode and cleanup code around
xilinx:
- Enable regular expression matching in board_fit_config_name_match()
- Fix FRU handling for 0xC1 format
- Fix Xilinx legacy format eeprom parsing
zynqmp:
- Some DT updates/cleanups
- Fix IDcode for xck24
- Remove empty mini config files
- Add support for k24
versal:
- Remove empty mini config files
versal_net:
- Setup timer when runs in EL3
- Build u-boot.elf for mini configurations
zynq-gem:
- Add support for new compatible strings
- Remove support for Avnet Ultrazedev SOM
- Handle SGMII with PCS phy
spi:
- Add support for gigadevice parts
misc:
- Remove CONFIG_TARGET_VENUS ifdef
- Add missing headers to remove sparse warnings
The FIT generated after the switch to using binman is using different
values for firmware and loadables properties compared to the old script.
With the old script:
firmware = "atf-1";
loadables = "u-boot", "atf-2", ...;
After switch to binman:
firmware = "u-boot";
loadables = "atf-1", "atf-2", ...;
This change result in SPL jumping directly into U-Boot proper instead of
initializing TF-A.
With this patch the properties change back to:
firmware = "atf-1";
loatables = "u-boot", "atf-2", ...;
Fixes: e0c0efff2a ("rockchip: Support building the all output files in binman")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add sha256 hash to FIT images when CONFIG_SPL_FIT_SIGNATURE=y.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
SPL load FIT images by reading the data aligned to block length.
Block length aligned image data is read directly to the load address.
Unaligned image data is written to an offset of the load address and
then the data is memcpy to the load address.
This adds a small overhead of having to memcpy unaligned data, something
that normally is not an issue.
However, TF-A may have a segment that should be loaded into SRAM, e.g.
vendor TF-A for RK3568 has a 8KiB segment that should be loaded into the
8KiB PMU SRAM. Having the image data for such segment unaligned result
in segment being written to and memcpy from beyond the SRAM boundary, in
the end this results in invalid data in SRAM.
Aligning the FIT and its external data to MMC block length to work
around such issue.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
SOM itself from PS point of view is using the same configuration as K26
that's why reuse that files and only change compatible strings.
The reason for creating own set of files is just in case when versions
start to diverge because of HW change, supply chain issue, etc.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/61f877ec0b480c5bd368a1211fc73ff7465016bd.1674043915.git.michal.simek@amd.com
When support for the Allwinner F1C100s SoC was originally introduced,
its DT lacked any MMC nodes, which upset our sunxi-u-boot.dtsi overlay,
when it tried to add an alias to the SD card. To quickly fix this back
then, we guarded that alias with a preprocessor macro.
Now the F1C100s family has gained MMC nodes, so we don't need the
special treatment anymore. Just remove this guard.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
This adds initial support for the Hardkernel Odroid Go Ultra.
The Odroid Go Ultra is a portable gaming device with the following
characteristics:
- Amlogic S922X SoC
- RK817 & RK818 PMICs
- 2GiB LPDDR4
- On board 16GiB eMMC
- Micro SD Card slot
- 5inch 854×480 MIPI-DSI TFT LCD
- Earphone stereo jack, 0.5Watt 8Ω Mono speaker
- Li-Polymer 3.7V/4000mAh Battery
- USB-A 2.0 Host Connector
- x16 GPIO Input Buttons
- 2x ADC Analog Joysticks
- USB-C Port for USB2 Device and Charging
The following are not yet handled:
- Battery RK818 Gauge and Charging
- 5inch 854×480 MIPI-DSI TFT LCD
Link: https://lore.kernel.org/r/20230119-u-boot-odroid-go-ultra-v1-2-f96bab9db396@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Add the required binman images to replace the Makefile rules which are
currently used. This includes subsuming:
- tpl/u-boot-tpl-rockchip.bin if TPL is enabled
- idbloader.img if either or both of SPL and TPL are enabled
- u-boot.itb if SPL_FIT is enabled
- u-boot-rockchip.bin if SPL is used, either using u-boot.itb when
SPL_FIT is enabled or u-boot.img when it isn't
Note that the intermediate files are dropped with binman, since it
producing everything in one pass. This means that
tpl/u-boot-tpl-rockchip.bin is not created, for example.
Note that for some 32-bit rk3288 boards, rockchip-optee.dtsi is included.
Signed-off-by: Simon Glass <sjg@chromium.org>
Enable multiple-images so we can generate more than one image. Also
add a comment for the end of the #if block.
Signed-off-by: Simon Glass <sjg@chromium.org>
Sync the px30 dtsi from Linux kernel v6.1.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
The Pinephone Pro is another device by PINE64. It's closely related
to the Pinebook Pro of which this initial support is derived from.
Specification:
- A variant of the Rockchip RK3399
- A 6 inch 720*1440 DSI display
- Front and rear cameras
- Type-C interface with alt mode display (DP 1.2) and PD charging
- 4GB LPDDR4 RAM
- 128GB eMMC
- mSD card slot
- An AP6255 module for 802.11ac WiFi and Bluetooth 5
- Quectel EG25-G 4G/LTE modem
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Initial support for the PinePhone Pro has now landed upstream in
Linux 6.1 RC1 so sync the dts from 6.2-rc1 for initial support.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Neural Compute Module 2(Neu2) IO board is an industrial form factor
IO board from Edgeble AI.
General features:
- microSD slot
- MIPI DSI connector
- 2x USB Host
- 1x USB OTG
- Ethernet
- mini PCIe
- Onboard PoE
- RS485, RS232, CAN
- Micro Phone array
- Speaker
- RTC battery slot
- 40-pin expansion
Neu2 needs to mount on top of this IO board in order to create complete
Edgeble Neural Compute Module 2(Neu2) IO platform.
Add support for it.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Add u-boot,dm-spl and u-boot,dm-pre-reloc related properties
for Rockchip RV1126 SoC.
Both eMMC and SD boot are tested in Edgeble Neu2 SoM.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Neural Compute Module 2(Neu2) IO board is an industrial form factor
evaluation board from Edgeble AI.
General features:
- microSD slot
- MIPI DSI connector
- 2x USB Host
- 1x USB OTG
- Ethernet
- mini PCIe
- Onboard PoE
- RS485, RS232, CAN
- Micro Phone array
- Speaker
- RTC battery slot
- 40-pin expansion
Neu2 needs to mount on top of this IO board in order to create complete
Edgeble Neural Compute Module 2(Neu2) IO platform.
Add support for it.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Neural Compute Module 2(Neu2) is a 96boards SoM-CB compute module
based on Rockchip RV1126 from Edgeble AI.
General features:
- Rockchip RV1126
- 2/4GB LPDDR4
- 8/16/32GB eMMC
- 2x MIPI CSI2 FPC connector
- Fn-link 8223A-SR WiFi/BT
Industrial grade (-40 °C to +85 °C) version of the same class of module
called Neu2k powered with Rockchip RV1126K.
Neu2 needs to mount on top of Edgeble IO boards for creating complete
platform solutions.
Add support for it.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
RV1126 is a high-performance vision processor SoC for IPC/CVR,
especially for AI related application.
It is based on quad-core ARM Cortex-A7 32-bit core which integrates
NEON and FPU. There is a 32KB I-cache and 32KB D-cache for each core
and 512KB unified L2 cache. It has build-in NPU supports INT8/INT16
hybrid operation and computing power is up to 2.0TOPs.
This patch add basic core dtsi support.
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Signed-off-by: Sugar Zhang <sugar.zhang@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
This synchronizes the Device Trees related to Puma RK3399 SoM with Linux
kernel next-20221114 to include two important changes pertaining to
eMMC and SD card instability.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The eMMC card has two supplies, VCC and VCCQ. The VCC supplies the NAND
array and the VCCQ supplies the bus. On Condor, the VCC is connected to
3.3V rail, while the VCCQ is connected to 1.8V rail. Adjust the pinmux
to match the bus, which is always operating in 1.8V mode.
Based on Linux commit 69efe4bbeda50745 ("arm64: dts: renesas: condor:
Switch eMMC bus to 1V8") from Wolfram Sang
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
This board requires SPI NOR fast-read, otherwise the SPI NOR
access returns corrupted data. Enable the fast-read explicitly
in DT as it has been disabled in the MTD subsystem by commit
d008190920 ("mtd: spi-nor: Mask out fast read if not requested in DT")
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
The timer units in the stm32mp15x CPUs have interrupts, depending on the
timer flavour either one "global" or four dedicated ones. Add the irqs
to the timer units on stm32mp15x.
Sync the DT Files with linux kernel v6.1 and with commit a9b70102253ce
("ARM: dts: stm32: Add timer interrupts on stm32mp15")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Remove unnecessary space in device tree stm32mp15xx-dkx.dtsi.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The include file stm32mp1-clksrc.h is not necessary for the SCMI STM32MP15
dtsi files as the clock tree is not defined in the U-Boot SCMI device tree;
these SCMI device tree only support TFABOOT with stm32mp15_defconfig,
SPL with the basic boot defconfig is not supported.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add support for USB2514B onboard hub on stm32mp157c EV1 board. The HUB
is supplied by a 3v3 PMIC regulator.
[backport from linux ad9591b01d24]
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Tested-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
phy-stm32-usbphyc bindings uses a connector node with vbus-supply
property.
[backport from linux 43e55d778a6b]
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
TI phy requires a reset before PHY address detection to make sure
correct strapping via MIO is detected. Facilitate the same using
ethernet-phy-id compatible string. GPIO reset entry will be added in
a separate commit.
This support is present in RevA but needs to be extended to RevB/1.0/1.1
versions which are built on top.
Fixes: 13622c7a9d ("arm64: zynqmp: Describe TI phy as ethernet-phy-id")
Signed-off-by: Harini Katakam <harini.katakam@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/6d500a83a787316353d4b26c75d1b51d29e3730e.1670854455.git.michal.simek@amd.com
