Add i.MX6ULZ cpu type and helper.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
When CONFIG_CLK enabled, use CLK UCLASS for clk related settings.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
hs: removed hunk in mxc_i2c_probe() as not longer in code
This converts the following to Kconfig:
CONFIG_ARCH_CPU_INIT
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Tested-by: Felix Brack <fb@ltec.ch>
Generate a MAC address based on the cpuid available in the efuse
block: Use the first 6 byte of the cpuid's SHA256 hash and set the
locally administered bits. Also ensure that the multicast bit is
cleared.
The MAC address is only generated and set if there is no ethaddr
present in the saved environment.
This is based off of Klaus Goger's work in 8adc9d
Signed-off-by: Rohan Garg <rohan.garg@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add ICID setup for the platform devices contained on this chip: usb,
sata, sdhc, sec. The ICID macros for SEC needed to be adapted because
the format of the registers is different.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
The current implementation assumes that the registers holding the ICIDs
are universally big endian. That's no longer the case on newer
platforms so update the code to take into account the endianness of
each register.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
As no gpio.h is defined for this architecture, to avoid
compilation failure, do not include <asm/arch/gpio.h> for
arch ls1088a.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
As no gpio.h is defined for this architecture, to avoid
compilation failure, do not include <asm/arch/gpio.h> for
arch ls2080a.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
As no gpio.h is defined for this architecture, to avoid
compilation failure, do not include <asm/arch/gpio.h> for
arch ls1028a.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
As no gpio.h is defined for this architecture, to avoid
compilation failure, do not include <asm/arch/gpio.h> for
arch ls2160a.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
I2C dm mode enablemenet causes below compilation errors:
In file included from include/config.h:8:0,
from include/common.h:20:
include/config_fallbacks.h:51:4: error: #error "Cannot define
CONFIG_SYS_I2C when CONFIG_DM_I2C is used"
# error "Cannot define CONFIG_SYS_I2C when CONFIG_DM_I2C is used"
^~~~~
In file included from include/config.h:8:0,
from include/common.h:20:
include/config_fallbacks.h:51:4: error: #error "Cannot define
CONFIG_SYS_I2C when CONFIG_DM_I2C is used"
# error "Cannot define CONFIG_SYS_I2C when CONFIG_DM_I2C is used"
^~~~~
board/freescale/lx2160a/lx2160a.c: In function 'board_early_init_f':
board/freescale/lx2160a/lx2160a.c:108:2: warning: implicit declaration
of function 'i2c_early_init_f'; did you mean 'arch_early_init_r'?
[-Wimplicit-function-declaration]
i2c_early_init_f();
^~~~~~~~~~~~~~~~
arch_early_init_r
drivers/i2c/mxc_i2c.c: In function 'mxc_i2c_probe':
drivers/i2c/mxc_i2c.c:824:8: warning: implicit declaration of function
'enable_i2c_clk';
did you mean 'enable_irq_wake'? [-Wimplicit-function-declaration]
ret = enable_i2c_clk(1, bus->seq);
^~~~~~~~~~~~~~
enable_irq_wake
So fix these compilation errors.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
This patch adds device tree and driver model watchdog support,
converts the legacy omap watchdog driver to driver model for
TI AM335x chipsets. The following compile warning is removed:
===================== WARNING ======================
This board does not use CONFIG_WDT (DM watchdog support).
Please update the board to use CONFIG_WDT before the
v2019.10 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
CONFIG_HW_WATCHDOG is no more a default option for AM33XX devices
after DT/DM conversion, adjusted kconfig accordingly.
DM watchdog support is enabled by default in SPL. The SPL image
doesn't fit into SRAM because of size constraints and build breaks
with an overflow. For this reason DM watchdog support should be
disabled in SPL, driver code should be adjusted accordingly to serve
this purpose.
Built and tested on AM335x device (BeagleboneBlack), compile tested
for all other AM33xx based boards.
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
The Secure Monitor offers multiple services, like returning the
SoC unique serial number, and can provide the "reboot reason" as
set by the previous booted system.
This extends the Amlogic specific "sm" cmd with a "reboot_reason" subcommand
to print or set a specified environment variable with the reboot reason in
human readable format.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This commit adds board support for Hikey960 board from Hisilicon. This
board is one of the Consumer Edition boards of the 96Boards family
powered by Kirin960 SoC.
More information about this board can be found in 96Boards website:
https://www.96boards.org/product/hikey960/
The initial supported/tested devices include:
- Debug serial
- SD
With these support, it's good enough for loading Linux Kernel from SD.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
This driver supports DDR3/LPDDR3/DDR4 SDRAM initialization.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
[cherry picked from commit 9fb0777ec3 with minor modifications]
Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
- Clean up and migrate to use common rockchip spl board file
- Clean up and migrate to use common rockchip board file
- Increase rk3288 CONFIG_SYS_BOOTM_LEN to 16MB
Add a board_early_init_f() in board_init_f() and move the board
specific init code into its own board file.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
boot_devices may defined in soc file, and used in board file,
we need to delear it in header file.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The boot source from BootRom is store at a fix offset of IRAM,
update to use the common macro instead of rk3399 specific one.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
This patch solves the following warnings:
arch/arm/mach-stm32mp/psci.c:
warning: no previous prototype for ‘psci_set_state’ [-Wmissing-prototypes]
warning: no previous prototype for ‘psci_arch_cpu_entry’ [-Wmissing-prototypes]
warning: no previous prototype for ‘psci_features’ [-Wmissing-prototypes]
warning: no previous prototype for ‘psci_version’ [-Wmissing-prototypes]
warning: no previous prototype for ‘psci_affinity_info’ [-Wmissing-prototypes]
warning: no previous prototype for ‘psci_migrate_info_type’ [-Wmissing-prototypes]
warning: no previous prototype for ‘psci_cpu_on’ [-Wmissing-prototypes]
warning: no previous prototype for ‘psci_cpu_off’ [-Wmissing-prototypes]
warning: no previous prototype for ‘psci_system_reset’ [-Wmissing-prototypes]
warning: no previous prototype for ‘psci_system_off’ [-Wmissing-prototypes]
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
We have convert all SoC to use DM timer or ARM arch/generic
timer, we can remove this rk_timer now.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Add pmu header file for rk3399 SoC, this will help
to configure pmu in sdram driver.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Add DdrMode structure with associated bit fields.
These would help to reconfigure sdram capabilities during
lpddr4 setup related configs.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Add DdrTimingC0 structure with associated bit fields.
These would help to reconfigure sdram capabilities during
lpddr4 setup related configs.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Add dram config macro for handling ddr version number.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
cs0_row, cs1_row and cs1_col needs more bits to show its
correct value, update to make use of both sys_reg2,
sys_reg3.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
(Squash similar patches into one patch)
Signed-off-by: Kever Yang <Kever.yang@rock-chips.com>
Add simplified and meaningful macro for all setting.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
(Squash the similar patches into 1 patch)
Signed-off-by: Kever Yang <Kever.yang@rock-chips.com>
New imx8 boards started adding duplicated UART init code.
Factor out this to common function sc_pm_setup_uart().
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Writing/updating boot image in nand device is not
straight forward in i.MX6 platform and it requires
boot control block(BCB) to be configured.
It becomes difficult to use uboot 'nand' command to
write BCB since it requires platform specific attributes
need to be taken care of.
It is even difficult to use existing msx-nand.c driver by
incorporating BCB attributes like mxs_dma_desc does
because it requires change in mtd and nand command.
So, cmd_nandbcb implemented in arch/arm/mach-imx
BCB contains two data structures, Firmware Configuration Block(FCB)
and Discovered Bad Block Table(DBBT). FCB has nand timings,
DBBT search area, page address of firmware.
On summary, nandbcb update will
- erase the entire partition
- create BCB by creating 2 FCB/DBBT block followed by
1 FW block based on partition size and erasesize.
- fill FCB/DBBT structures
- write FW/SPL on FW1
- write FCB/DBBT in first 2 blocks
for nand boot, up on reset bootrom look for FCB structure in
first block's if FCB found the nand timings are loaded for
further reads. once FCB read done, DTTB will load and finally
firmware will be loaded which is boot image.
Refer section "NAND Boot" from doc/imx/common/imx6.txt for more usage
information.
Reviewed-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Sergey Kubushyn <ksi@koi8.net>
Signed-off-by: Shyam Saini <shyam.saini@amarulasolutions.com>
Add code to print the channel stride, this would help to
print the stride of associated channel.
Here is sample print on LPDDR4, 50MHz.
256B stride
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Add sdram ddr info print support, this would help to
observe the sdram base parameters.
Here is sample print on LPDDR4, 50MHz channel 0
BW=32 Col=10 Bk=8 CS0 Row=15 CS1 Row=15 CS=2 Die BW=16
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Add sdram driver to handle debug across rockchip SoCs.
This would help to improve code debugging feature for
sdram drivers in rockchip family, whoever wants to
debug the driver should call these core debug code on
their respective platform sdram drivers.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Add DDR4 enum number in common header.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
dramtype enum numbers as common across all dram controllers
in rockchip, so move the eneum values in common header.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Move common sdram structures like sdram_cap_info, sdram_base_params
into sdram_common header, this would help to reuse the same
from another controllers like px30.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Most of the ddr parameters are common in rk3399_base_params
structure and which would reuse it in another controller like
px30 in future.
So, rename the structure from rk3399_base_params into
sdram_base_params.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Group common ddr attributes like
- rank
- col
- bk
- bw
- dbw
- row_3_4
- cs0_row
- cs1_row
- ddrconfig
into a common cap_info structure for more code readability and extend
if possible based on the new features.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
- Various FS/disk related fixes with security implications.
- Proper fix for the pci_ep test.
- Assorted bugfixes
- Some MediaTek updates.
- 'env erase' support.
When a crash occurs in thumb mode the crash dump is incorrect. This is due
to the usage of a non-existing configuration variable CONFIG_ARM_THUMB in
the definition of macro thumb_mode(regs).
Use CONFIG_IS_ENABLED(SYS_THUMB_BUILD) to detect that the code has been
compiled for thumb mode. Remove ARM_THUMB from config_whitelist.txt.
With the patch crash dumps indicate thumb mode correctly.
On a system with thumb mode:
=> exception unaligned
data abort
pc : [<8f7a2b52>] lr : [<8f7ab1ef>]
reloc pc : [<1780cb52>] lr : [<178151ef>]
sp : 8ed8c3f8 ip : 8f7a2b4d fp : 00000002
r10: 8f7f8228 r9 : 8ed95ea8 r8 : 8ed99488
r7 : 8f7ab141 r6 : 00000000 r5 : 8ed8c3f9 r4 : 8f7f6390
r3 : 8ed9948c r2 : 00000001 r1 : 00000000 r0 : 8f7f6390
Flags: nzCv IRQs off FIQs off Mode SVC_32 (T)
Code: 8f7e 466d f105 0501 (e9d5) 6700
The Flags line has '(T)' and in the Code line the output is in u16 groups.
On a system without thumb mode:
=> exception breakpoint
prefetch abort
pc : [<7ff5a5c8>] lr : [<7ff675ec>]
reloc pc : [<0000e5c8>] lr : [<0001b5ec>]
sp : 7ee0ad80 ip : 7ff5a5cc fp : 7ff674cc
r10: 00000002 r9 : 7ef0bed8 r8 : 7ffd6214
r7 : 7ef0e080 r6 : 00000000 r5 : 7ffd4090 r4 : 00000000
r3 : 7ef0e084 r2 : 00000001 r1 : 00000000 r0 : 7ffd4090
Flags: nzCv IRQs off FIQs off Mode SVC_32
Code: e1a0500d e2855001 e1c560d0 e3a00001 (e12fff1e)
The Flags line does not show '(T)' and in the Code line the output is in
u32 groups.
Reported-by: Marek Vasut <marex@denx.de>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
There is no need for to include this header here, so drop it.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
At the moment the H6 DRAM driver only supports LPDDR3 DRAM.
Extend the driver to cover DDR3 DRAM as well.
The changes are partly motivated by looking at the ZynqMP register
documentation, partly by looking at register dumps after boot0/libdram
has initialised the controller.
Many thanks to Jernej for contributing some fixes!
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Currently the H6 DRAM driver only supports one kind of LPDDR3 DRAM.
Split the timing parameters for this LPDDR3 configuration into a
separate file, to allow selecting an alternative later at compile time
(as the sunxi-dw driver does).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
KM Kirkwood boards now implement the driver model for its SPI flash
interface. Therefore, the old board specific claim and release functions
can be deleted. The preprocessor definition CONFIG_SYS_KW_SPI_MPP is yet
unused as well. All its appearances and dependencies are removed in the
kirkwood_spi driver, header files and finally the configuration whitelist.
Signed-off-by: Pascal Linder <pascal.linder@edu.hefr.ch>
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Signed-off-by: Stefan Roese <sr@denx.de>
- add support for unique generated MAC adresses from SoC serial,
limited to Amlogic GXL/GXM boards for now
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=BL1s
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20190704' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic
- fix khadas-vim README
- add support for unique generated MAC adresses from SoC serial,
limited to Amlogic GXL/GXM boards for now
Add support for generating an unique MAC address using the SoC internal
serial number from the Secure Monitor interface.
The algorithm generates an unicast locally administered 6bytes minus 2bits
address using an crc16 of the serial for the top 16bits with the lower 2 bits
masked to setup the unicast locally administered property and a crc24 for
the lower 24bits.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The Secure Monitor interface permits retrieving the SoC Serial Number,
add a function to retrieve it.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Converted to use fsl_esdhc_imx for i.MX platforms.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Tested-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Martyn Welch <martyn.welch@collabora.com>
Acked-by: Jason Liu <Jason.hui.liu@nxp.com>
LS1028A includes an integrated PCI bus with 11 PCI functions residing on
bus 0. ECAM plus the device register space takes up 256MB of address
space.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Layerscape began to use two eSDHC controllers, for example,
LS1028A. They are same IP block with same reference clock.
This patch is to add clock support for the second eSDHC.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Enable workaround for USB erratum A-008997. Here PCSTXSWINGFULL
registers has been moved to DSCR as compared to other Layerscape SoCs
where it was in SCFG.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Without this definition, fsl_esdhc will access reserved registers
on i.MX chips, so define ARCH_MXC to fix it.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Correct uart clock root ID. Incorrect ID may result the
clock is gated because rate value 0 is returned in
imx_get_uartclk()
The ID can be ignored if CONFIG_SKIP_LOWLEVEL_INIT is not enabled
because init_clk_uart() will enable all uart clocks in that case.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Add common plugin codes to call ROM's hwcnfg_setup and generate IVT2
header.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This function will attempt to look up an Ethernet address in the DTB
that was passed in from cboot. It does so by first trying to locate the
default Ethernet device for the board (identified by the "ethernet"
alias) and if found, reads the "local-mac-address" property. If the
"ethernet" alias does not exist, or if it points to a device tree node
that doesn't exist, or if the device tree node that it points to does
not have a "local-mac-address" property or if the value is invalid, it
will fall back to the legacy mechanism of looking for the MAC address
stored in the "nvidia,ethernet-mac" or "nvidia,ether-mac" properties of
the "/chosen" node.
The MAC address is then written to the default Ethernet device for the
board (again identified by the "ethernet" alias) in U-Boot's control
DTB. This allows the device driver for that device to read the MAC
address from the standard location in device tree.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Tegra186 build are currently dealt with in very special ways, which is
because Tegra186 is fundamentally different in many respects. It is no
longer necessary to do many of the low-level programming because early
boot firmware will already have taken care of it.
Unfortunately, separating Tegra186 builds from the rest in this way
makes it difficult to share code with prior generations of Tegra. With
all of the low-level programming code behind Kconfig guards, the build
for Tegra186 can again be unified.
As a side-effect, and partial reason for this change, other Tegra SoC
generations can now make use of the code that deals with taking over a
boot from earlier bootloaders. This used to be nvtboot, but has been
replaced by cboot nowadays. Rename the files and functions related to
this to avoid confusion. The implemented protocols are unchanged.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Some devices may restrict access to the PMC to TrustZone software only.
Non-TZ software can detect this and use SMC calls to the firmware that
runs in the TrustZone to perform accesses to PMC registers.
Note that this also fixes reset_cpu() and the enterrcm command on
Tegra186 where they were previously trying to access the PMC at a wrong
physical address.
Based on work by Kalyani Chidambaram <kalyanic@nvidia.com> and Tom
Warren <twarren@nvidia.com>.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
There's no need to replicate the pmu.h header file for every Tegra SoC
generation. Use a single header that is shared across generations.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This patch adds the missing GRF bit definitions for UART3 on the RK3399.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Stefano Babic <sbabic@denx.de>
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Stefano Babic <sbabic@denx.de>
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Stefano Babic <sbabic@denx.de>
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Add a driver which supports transmitting digital sound to an audio codec.
This uses fixed parameters as a device-tree binding is not currently
defined.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add a driver for the audio hub. This is modelled as a misc device which
supports writing audio data from I2S.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The lx2160a have up to 6 PCIe controllers and have different
address and size of PCIe region.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
The LS2080A has 8GB region for each PCIe controller, while the
other platforms have 32GB.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Some H6 boards have a watchdog which didn't make the SoC
reboot properly.
Reason is still unknown but several people have test it.
Chen-Yu Tsai :
Pine H64 = H6 V200-AWIN H6448BA 7782 => OK
OrangePi Lite 2 = H6 V200-AWIN H8068BA 61C2 => KO
Martin Ayotte :
Pine H64 = H8069BA 6892 => OK
OrangePi 3 = HA047BA 69W2 => KO
OrangePi One Plus = H7310BA 6842 => KO
OrangePi Lite2 = H6448BA 6662 => KO
Clément Péron:
Beelink GS1 = H6 V200-AWIN H7309BA 6842 => KO
After the series of result, Icenowy try to reach Allwinner about this
issue but they seems not interested to investigate it.
As we don't have the ARIS coproc to do power management and watchdogis
the only solution to reset the board.
So, Change from watchdog to R_watchdog to allow a reboot on all H6
boards.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
While converting CONFIG_SYS_[DI]CACHE_OFF to Kconfig, there are instances
where these configuration items are conditional on SPL. This commit adds SPL
variants of these configuration items, uses CONFIG_IS_ENABLED(), and updates
the configurations as required.
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Trevor Woerner <trevor@toganlabs.com>
[trini: Make the default depend on the setting for full U-Boot, update
more zynq hardware]
Signed-off-by: Tom Rini <trini@konsulko.com>
Improvements and new features:
- split more rockchip pinctrl_core feature into per SoC
- enable TPL for evb-rk3399 board
- enable TPL/SPL for evb-px5 board
- enable TPL and OP-TEE support for evb-rk3229
- update fix in arm common assembly start code for rockchip header file
- update default SPL_FIT_GENERATOR for rockchip
- rk3399 boards update to use '-u-boot.dtsi'
- add new rk3399 boards: Nanopi M4, Nanopc T4
- enable sound for chromebook_minnie
Adds support for Amlogic G12A USB Device mode.
The DWC2 Controller behind the Glue can be connected to an OTG
capable PHY. The Glue setups the PHY mode.
This patch implements Device mode support by adding a board_usb_init/cleanup
setting up the DWC2 controller and switch the OTG capable port to Device
before starting the DWC2 controller in Device mode.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
boot0.h and gpio.h will be used by system and include by
'asm/arch/', each of them need of a copy from 'asm/arch-rockchip'.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add the PL310 macros for latency control setup, read and write bits.
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
------------------------
- warp7 to DM
- kp_imx53 to DM
- Warnings in DT
- MX8QM support
- colibri-imx6ull to DM
- imx7d-pico to DM
- ocotp for MX8
-----BEGIN PGP SIGNATURE-----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=CzWQ
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20190426' of git://git.denx.de/u-boot-imx
Porting to DM and i.MX8
------------------------
- warp7 to DM
- kp_imx53 to DM
- Warnings in DT
- MX8QM support
- colibri-imx6ull to DM
- imx7d-pico to DM
- ocotp for MX8
Rockchip use 'arch-rockchip' instead of arch-$(SOC) as common
header file path, so that we can get the correct path directly.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
rockchip platform header file is in 'arch-rockchip'
instead of arch-$(SOC) for all SoCs.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
TIMER7_BASE is no used by source code now, remove it.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Remove duplicate function declarations from the SCFW API header file.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Add support for the Amlogic G12A SoC, which is a mix between the
new physical memory mapping of AXG and the functionnalities of
the previous Amlogic GXL/GXM SoCs.
To handle the internal ethernet PHY, the Amlogic G12A SoCs now
embeds a dedicated PLL to feed the internal PHY.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add basic support for the Amlogic G12A clock controller based on
the AXG driver.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Allow PSCI layer to handle any SiP service functions added by
platform vendors. PSCI layer will look for SiP service function
in the SiP function table located in '._secure_svc_tbl_entries'
section if the SMC function identifier is not found in the PSCI
standard functions table. Use DECLARE_SECURE_SVC macro to declare
and add platform specific SiP service function.
This new section '._secure_svc_tbl_entries' is located next to
'._secure.text' section. Refer to arch/arm/cpu/armv8/u-boot.lds.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
-----------
- DM support in sata
- Toradex Board to DM
- wandboard to DM
- tbs2910 to DM
- GE boards to DM
- VHybrid boards to DM
- DM_VIDEO for i.MX
-----BEGIN PGP SIGNATURE-----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=KLsH
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20190415' of git://git.denx.de/u-boot-imx
Move to DM
-----------
- DM support in sata
- Toradex Board to DM
- wandboard to DM
- tbs2910 to DM
- GE boards to DM
- VHybrid boards to DM
- DM_VIDEO for i.MX
Add support for Vybrid's UART2 (Colibri UART_B).
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
The DDR memory controller include file for the Vybrid uses
iomux_v3_cfg_t without actually including iomux-vf610.h.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Extend the driver to build with DM_VIDEO enabled. DTS files
must additionally include 'u-boot,dm-pre-reloc' property in
soc and ipu nodes to enable driver binding to ipu device.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
This code allows reusing the default u-boot as in the late board init, the
default envs are restored and proper recovery scripts executed.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Provide function to enable I2C clocks for vf610 - in the generic code.
This function overrides the default weak function implementation (which
only returns 1).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
- ath79: small fixes, add support for QCA9563 SoC and AP152 reference board
- mscc: small fixes, add network support for JR2 and ServalT SoCs
- bmips: small fixes, enable more drivers for ARM specific BCM6858 and BCM63158 SoCs
- MIPS: fix redundant relocation of initrd images
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEiQkHUH+J02LLC9InKPlOlyTyXBgFAlywtKQACgkQKPlOlyTy
XBgYbBAAlRLhN52f2vv9Hng/tfCAuZk7c9tJ+b/5i36ZoJNozeaiOBgwVl3eeEa9
v4SeKz4J+9FJLOSZkIPrCvX+HaACQn7Pqw/64h3JE8TEzfU5lgmV4Xk2dcXtkmEL
L5PTQoNMZDgQaeltLtN29yIW5lVxx0NUN9O0FLY5+R/ptXlCFaAGdgSuXH36boDR
/cvfLlaZPM/hA7l3wRUjWa17L8MNEon4+cqLkzDyTTihdHOdZA4P1O7ce/XffGQp
BAiSta4EztB1xs0oTAOEmUJp1v8Ae7yRuFoZaCp+Dgq+0WOTbxDW4J57fTaphES1
su3yoYjju+M/dUb/sWmOQNjeIchJPYWcpiOl9E8jQ/l2SaBJ6Oxmg7PxC3Ww0X2z
JdF6mcKeaDH3WYO20FeC6xb9Q9FN2yX4rcW/Yg46TdeJ3T2sj8A19ZCHoeAQRl0I
68SbAaDJw/K3fTBFPd9VyQQQawPbyhmpdQAOWtixNWBFIBbZpqI4o1DMJKJRoxqd
Ail++ysLUICB0XXg0rGI+dFusjcu9AAeRODc11dtGa0YBh2Y28JrJ4OuV14GYQhe
5J8BquRaDADA3iK/+3C6TUSQGhb5pFXTcsdNBC9zBPb/ePeMDfZxBcB2vCOnZDZ1
m0kR5qnsz4IH8/rCmJ5wmMBh6JuyPoCSdiTVuuU5CuCVGYbmJuE=
=NrV8
-----END PGP SIGNATURE-----
Merge tag 'mips-pull-2019-04-12' of git://git.denx.de/u-boot-mips
- mt76xx: add USB support, small fixes
- ath79: small fixes, add support for QCA9563 SoC and AP152 reference board
- mscc: small fixes, add network support for JR2 and ServalT SoCs
- bmips: small fixes, enable more drivers for ARM specific BCM6858 and BCM63158 SoCs
- MIPS: fix redundant relocation of initrd images
As no gpio.h is defined for this architecture, to avoid
a compilation failure, do not include <asm/arch/gpio.h>
for arch bcm63158.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
As no gpio.h is defined for this architecture, to avoid
compilation failure, do not include <asm/arch/gpio.h> for
arch bcm6858.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Add configuration for the MT41K128M16JT125K memory modules as used on the
Bosch Guardian device.
Based on a patch by:
Govindaraji Sivanantham <Govindaraji.Sivanantham@in.bosch.com>
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
[checkpatch.pl cleanup by Martyn Welch]
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
On modern Allwinner SoCs (tested: H2+, A64, H5, H6) the BootROM can
actually load the SPL also from sector 256 (128KB) of an SD card or eMMC
chip. For more details, see [1].
In this case the boot source indicator (written at offset 0x28 of SRAM A1)
has bit 4 set, so it's 0x10 for SD card and 0x12 for eMMC.
Add those new values to the existing boot source check to allow booting
the SPL from those "high" disk offsets as well. For this to work, the
value of CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR needs to be adjusted,
for instance to 0x140 (right after the high SPL). Doing this dynamically
sounds desirable, but looks nasty to implement.
[1] https://groups.google.com/forum/#!topic/linux-sunxi/MaiijyaAFjk
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Barrier transactions from CCI400 need to be disabled till
the DDR is configured, otherwise it may lead to system hang.
The patch adds workaround to fix the erratum.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
sec_firmware reserves JR3 for it's own usage and deletes the JR3 node
from the device tree. This causes this warning to be issued when doing
the device tree fixup:
WARNING could not find node fsl,sec-v4.0-job-ring: FDT_ERR_NOTFOUND.
Fix it by excluding the device tree fixup for the JR reserved by
sec_firmware.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Horia Geanta <horia.geanta@nxp.com>
Reviewed-by: Bharat Bhushan <bharat.bhushan@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
The SEC QI ICID setup in the QIIC_LS register is actually an offset
that is being added to the ICID coming from the qman portal. Setting
it with a non-zero value breaks SMMU setup as the resulting ICID is
not known. On top of that, the SEC QI ICID must match the qman portal
ICIDs in order to share the isolation context.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Horia Geanta <horia.geanta@nxp.com>
Reviewed-by: Bharat Bhushan <bharat.bhushan@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Moves FSL_TZASC_400 and FSL_TZPC_BP147 configs to Kconfig
for LS1088A and LS2088A platforms.
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
LX2160AQDS is a development board that supports LX2160A
family SoCs. This patch add base support for this board.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
[PK: Sqaush patch for "secure boot defconfig" & add maintainer]
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
As per hardware documentation,
CONFIG_SYS_FSL_PEBUF_BASE for lx2160a is 0x1c00000000
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Since there is the SPL_USB_HOST_SUPPORT for enabling USB support in SPL,
makes more sense to rename the SPL_USB_SUPPORT as SPL_USB_STORAGE.
Everything that is not part of the usb storage support in SPL is now
build under SPL_USB_HOST_SUPPORT.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Bob is a 10-inch chromebook produced by Asus. It has two USB 3.0 type-C
ports, 4GB of SDRAM, WiFi and a 1280x800 display. It uses its USB ports
for both power and external display. It includes a Chrome OS EC
(Cortex-M3) to provide access to the keyboard and battery functions.
Support so far includes only:
- UART
- SDRAM
- MMC, SD card
- Cros EC (but not keyboard)
Not included:
- Keyboard
- Display
- Sound
- USB
- TPM
Bob is quite similar to Kevin, the Samsung Chromebook Plus, but support
for this is not provided in this series.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Allow rockchip boards to use GPIOs before driver model is ready. This is
really only useful for setting GPIOs to enable the early debug console, if
needed on some platforms.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
At present this enum is only available to rk3288. Move it so that other
rockchip SoCs can access it. It is needed for the SPL GPIO driver for
rk3999 in a later patch.
Also adjust the enum name to lower case.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add support for setting pinctrl and clock for I2S on rk3288. This allows
the sound driver to operate. These settings were created by rkmux.py
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This adds video output support for Amlogic GXBB/GXL/GXM chips.
The supported ports are CVBS and HDMI (based on DW_HDMI).
When using HDMI, only DMT modes are supported.
There is support for simple-framebuffer (CONFIG_VIDEO_DT_SIMPLEFB)
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jorge Ramire-Ortiz <jramirez@baylibre.com>
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
[narmstrong: fixed defines alignment in meson_canvas.c]
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Apply errata based on PL310 version instead of compile
time. Also set Prefetch offset to 15, since it improves
memcpy performance by 35%. Don't enable Incr double
Linefill enable since it adversely affects memcpy
performance by about 32MB/s and reads by 90MB/s. Tested
with 4K to 16MB sized src and dst aligned buffer.
Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
According to "Table 5-1. Boot Device Select" (page 335,
i.MX 6Dual/6Quad Applications Processor Reference Manual, Rev. 4, 09/2017)
the BOOT_CFG1[3] have following values (regarding EIM booting):
0 - NOR flash and 1 - ONENAND
This commit provides correct identification of the boot medium for IMX6Q
boards booting from NOR memory (MCCMON6 is one of them).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
We have converted mmc to driver model on Poplar. So let's clean up
board level mmc initialization code.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Similar changes was done for Zynq in past and this patch just follow
this pattern to separate cpu code from SoC code.
Move arch/arm/cpu/armv8/zynqmp/* -> arch/arm/mach-zynqmp/*
And also fix references to these files.
Based on
"ARM: zynq: move SoC sources to mach-zynq"
(sha1: 0107f24036)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add common reset driver for all Allwinner SoC's.
Since CLK and RESET share common DT compatible, it is CLK driver
job is to bind the reset driver. So add CLK bind call on respective
SoC driver by passing ccu map descriptor so-that reset deassert,
deassert operations held based on ccu reset table defined from
CLK driver.
Select DM_RESET via CLK_SUNXI, this make hidden section of RESET
since CLK and RESET share common DT compatible and code.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add initial clock driver for Allwinner A64.
Implement USB clock enable and disable functions for
OHCI, EHCI, OTG and USBPHY gate and clock registers
via ccu clk gate table.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
To use TWI0/1/2 the user can select CONFIG_I2C#_ENABLE.
However even the controller is enabled, the mux for the pins
are not set.
This patch follows the existing mux method. Since the pads are
different, separate check is added for each i2c.
Tested with A64-SOM204 board.
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The ICIDs for the qdma device are not configured through SCFG but
through some registers found in the actual device register block.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS1043A/LS1023A 23x23 package silicon has different SVR:VAR_PER.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
It enables DWC2 OTG gadget driver support for Poplar board. As
usb2_phy_init() is being always called from board_init(), we can save
the call from board_usb_init().
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The CR80 register has multiple interrupt bits, the code is supposed
to check bit 8 but instead uses a logical and. In most cases this
probably did not affect real operations since at that stage typically
none of the other bits are set.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
According to the data sheet bits 10-8 are PHYDRAM_CK_EN. Fix mask
to allow setting PHYDRAM_CK_EN correctly.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
The Vybrid reference manual VFXXXRM Rev. 0 10/2016 states in chapter
5.2.6.1 DUMMY PADS (DDR/QuadSPI) that those pads need to be programed
for correct operation of DDR. Assume the default DDR pin configuration
which seems to work well on a Colibri VF50.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
When running usb dwc3 gadget driver, we meet random USB enumeration failure in fastboot.
The root cause is a cache coherence issue. When it happens, the ctrl_req in
gadget driver is allocated at 0xfe932f40, and the usb_composite_dev (cdev)
is allocated at 0xfe932f60. So after we submit the setup request (cache flushed) to USB
controller, any accessing to usb_composite_dev variable will cause the cache line refill, then
when setup transfer is completed, reading the setup data in ctrl_req will gets old value from
cache not from memory.
The ctrl_req is allocated by API dma_alloc_coherent, but u-boot don't have cohernet memory.
so it still needs cache maintain operations before/after HW accessing. Since the cache flush or
invalidate bases on cache line, so when the allocated memory size is not cache line aligned,
potentially it may meet such issue.
This patch modifies the dma_alloc_coherent API to round the size to cache line aligned.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Refactor dram_pll_init to accept args to configure different pll freq.
Introduce dram_enable_bypass and dram_disable_bypass
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Enable DM for USB peripheral in the musb-new driver.
Also make sure that the driver can be used in the SPL.
This implies that:
* the driver must work with and without the OF_CONTROL option. That
in turn, implies that the platform data can be passed in a struct
ti_musb_platdata or be read from the dtb
* usb.o is linked in the SPL if host support is enabled
Another change is that the driver does not fail to bind (and stop the boot
process) if one of the child driver does not bind. Reporting the error is
enough. This kind of error would appear if the port is configured in the
DTS but the driver is not activated in the config.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add support for lx2160a SoC
-----BEGIN PGP SIGNATURE-----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=aT7d
-----END PGP SIGNATURE-----
Merge tag 'fsl-qoriq-for-v2019.01-rc2' of git://git.denx.de/u-boot-fsl-qoriq
Add TFA boot flow for some Layerscape platforms
Add support for lx2160a SoC
[trini: Add a bunch of missing MAINTAINERS entries]
Signed-off-by: Tom Rini <trini@konsulko.com>
This allows the driver to be used without OF_CONTROL.
AM335x support DM_SPL but does not use SPL_OF_CONTROL. Enabling DM_I2C in
SPL thus requires that the omap I2C can be passed platdata.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Move away from SoC specific headers to handle different register layout.
Instead use driver data to get appropriate register layouts like in the
kernel. While at it, perform some mostly cosmetic alignment/cleanup in
the functions being updated.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
In some STM32 SoC packages, GPIO bank has not always 16 gpios.
Several cases can occur, gpio hole can be located at the beginning,
middle or end of the gpio bank or a combination of these 3
configurations.
For that, gpio bindings offer the gpio-ranges DT property which
described the gpio bank mapping.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
NXP layerscape architecture Chassis 3.2 builds upon chassis3
architecture with changes like DDR Memory map change,
removal of IFC and support of upto 8 I2C controller.
Patch add README.lsch3_2 and the above changes under
macro CONFIG_NXP_LSCH3_2.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Some lsch3 based SoCs like lx2160a contains three
serdes modules.
Add support for third serdes protocol in lsch3
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Workaround of erratum A010539 clears the RCW source field in PORSR1
register, causing failure of detecting boot source using this method.
Use SMC call if U-Boot runs at EL2. If SMC is not implemented or
running at EL3, continue to read PORSR1 and presume QSPI as boot
source if erratum workaround A010539 is enabled and RCW source is
cleared.
Signed-off-by: York Sun <york.sun@nxp.com>
Adds SMC calls for getting DDR size and bank info for TFABOOT.
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
PORSR register holds the cfg_rcw_src field which can be used
to identify boot source.
Further, it can be used to select the environment location.
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
[YS: fix multiple checkpatch issues]
Reviewed-by: York Sun <york.sun@nxp.com>
Move static definitions to cpu.c file, as it doesn't allow
the cpu.h file to be included in multiple c files.
Signed-off-by: York Sun <york.sun@nxp.com>
This patch sets the PLL of CPU cluster B (BPLL) to 600 MHz.
This decreases the boot time of Linux 4.19 by about 8%.
The 600 MHz are inspired by the 600 MHz used for LPLL initialization
(came in with commit 9f636a249c).
Tested on RK3399-Q7 on Haikou base board.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Make adjustments to the rv1108 clock driver in order to align it
with the internal Rockchip version.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Rockchip socs can route the debug uart pins through the d+ and d- pins
of one specific usbphy per soc. Add a config option and implement the
setting on the rk3188.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[Fixed up to mark grf as maybe unused:]
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This patch adds pinctrl support for MT7629 SoC. The IO core found on
the SoC has the registers for pinctrl, pinconf and gpio mixed up in
the same register range. Hence the driver also implements the gpio
functionality through UCLASS_GPIO.
This also creates a common file as there might be other chips that use
the same binding and driver, then being a little more abstract could
help in the long run.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds a general board file based on MT7629 SoCs from MediaTek.
Apart from the generic parts (cpu) we add some low level init codes
and initialize the early clocks.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The Amlogic Meson SoCs ROM supports a boot over USB with a custom protocol.
When no other boot medium are available (or by forcing the USB mode), the
ROM sets the primary USB port as device mode and waits for a Host to
enumerate.
When enumerated, a custom protocol described at [1] permits writing to
memory and execute some specific FIP init code to run the loaded
Arm Trusted Firmware BL2 and BL3 stages before running the BL33 stage.
In this mode, we can load different binaries that can be used by U-boot
like a script image file.
This adds support for a custom USB boot stage only available when the
boot mode is USB and the script file at a pre-defined address is valid.
This support was heavily copied from the Sunxi Allwinner FEL U-Boot support.
The tool pyamlboot described at [2], permits using this boot mode on boards
exposing the first USB port, either as OTG or Host port.
[1] https://github.com/superna9999/pyamlboot/blob/master/PROTOCOL.md
[2] https://github.com/superna9999/pyamlboot/blob/master/README.md
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This patch adds a minimal clock driver for the Amlogic AXG SoC to handle
the basic gates and PLLs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This patch adds support for the Amlogic AXG SoC, which is very close from
the Amlogic GXL SoCs with :
- Same 4xCortex-A53 CPUs but clocked at 1.2GHZ max
- DDR Interface limited to DDR4 16bit
- The whole physical register address space has been moved to 0xfxxxxxxx
- The pinctrl setup has changed
- The clock tree is different enough to use a different driver
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
We are about to add support for the Amlogic AXG SoC. While very close to
the Gx SoC family, we will need to handle a few thing which are different
in this SoC. Rework the meson arch directory to prepare for this.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Drop the _AC and UL macros from common.h. Linux headers is the original
source of this macro, so keep its definition in the same header.
Update existing users of these macros to include const.h directly.
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Rick Chen <rick@andestech.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Allow EL3 to handle all the External Abort and SError interrupt
exception occur in all exception levels.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Allwinner A64 has a I2C controller, which is in the R_ MMIO zone and has
two groups of pinmuxes on PL bank, so it's called R_I2C.
Add support for this I2C controller and the pinmux which doesn't conflict
with RSB.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Vagrant Cascadian <vagrant@debian.org>
Acked-by: Jagan Teki <jagan@openedev.com>
A64 and H6 support automatic delay calibration and Linux driver uses it
instead of hardcoded delays. Add support for it to u-boot driver.
Fixes eMMC instability on Pinebook
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Cc: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Update TI Keystone 2 driver to re-use common mdio lib.
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Networking support for all TI K2 boards converted to use DM model and
CONFIG_DM_ETH enabled in all corresponding defconfig files, hence drop
unused non DM K2 networking code.
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
At the moment we rely on the infamous get_ram_size() function to learn
the actual DRAM size in U-Boot proper. This function has two issues:
1) It only works if the DRAM size is a power of two. We start to see
boards which have 3GB of (usable) DRAM, so this does not fit anymore.
2) As U-Boot has no notion of reserved memory so far, it will happily
ride through the DRAM, possibly stepping on secure-only memory. This
could be a region of DRAM reserved for OP-TEE or some other secure
payload, for instance. It will most likely crash in that case.
As the SPL DRAM init routine has very accurate knowledge of the actual
DRAM size, lets propagate this wisdom to U-Boot proper.
We re-purpose a currently reserved word in our SPL header for that.
The SPL itself stores the detected DRAM size there, and bumps the SPL
header version number in that case. U-Boot proper checks for a valid
SPL header and a high enough version number, then uses the DRAM size
from there. If the SPL header field is not sufficient, we fall back to
the old DRAM scanning routine.
Part of the DRAM might be present and probed by SPL, but not accessible
by the CPU. They're restricted in the main U-Boot binary, when accessing
the DRAM size from SPL header.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
On Allwinner SoCs we use some free bytes at the beginning of the SPL image
to store various information. We have a version byte to allow updates,
but changing this always requires all tools to be updated as well.
Introduce the concept of semantic versioning [1] to the SPL header:
The major part of the version number only changes on incompatible
updates, a minor number bump indicates backward compatibility.
This patch just documents the major/minor split, adds some comments
to the header file and uses the versioning information for the existing
users.
[1] https://semver.org
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
This is required for the current Linux kernel to reboot. It should also
probably be fixed in Linux.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add the power domain DM driver for i.MX8, that it depends on the DTB
power domain trees to generate the power domain provider devices. Users
need to add power domain trees with property "compatible = "nxp,imx8-pd";"
When power on a PD device, the driver will power on its ancestor PD
devices in power domain tree.
When power off a PD device, the driver will check its child PD devices
first. Only if all child PD devices are off, then power off the current PD
device. Then the driver checks sibling PD devices. If sibling PD devices
are off, then it will power off parent PD device.
There is no counter maintained in this driver, but a state to hold current
on/off state. So the request and free functions are empty.
The power domain implementation in i.MX8 DTB set the "#power-domain-cells"
to 0, so there is no ID binding with each PD device. We don't use "id"
variable in struct power_domain. At the same time, we have to set of_xlate
to empty to bypass standard of_xlate in uclass driver.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>