Use the common RCAR_GEN2 config option instead of enumerating
each SoC and having a lengthy ifdef clause. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
wait_for_bit callers use the 32 bit LE version
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This adds SH_ETHER to drivers/net/Kconfig and convert to Kconfig.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
When we using network on board using sh-eth, it prints a lot of
"CACHE: Misaligned operation at range" messages.
This commit fixes this problem.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This changes Change structure used in sh_eth_read and sh_eth_write function
from struct sh_eth_dev to struct sh_eth_info. This is necessary to convert
to Driver Model.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
bd_t is not used in sh_eth_config(). This deletes bd_t from sh_eth_config()
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This fixes the chord style checked by checkpatch.pl.
Details of change details are as follows:
- Fix typo
Change from alligned to aligned.
- Remove whitespace before ','
- Add spaces preferred around that '|'
- Fix missing a blank line after declarations
- Remove space after a cast declaration
- Fix format of block comments
- Add a blank line after function/struct/union/enum declarations
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add a b53_reg read/write command which allows inspecting the switch
registers. Because the Broadcom BCM53xx registers have different sizes,
we need to split the accesses in 8, 16, 32, 48 or 64 bits to obtain
expected results.
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Make sure that we pad small packets to a minimum length of 60 bytes
(without FCS). This is necessary to interface with Ethernet switches
that will reject RUNT frames unless padded correctly.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add a minimalistic Broadcom BCM53xx (roboswitch) switch driver similar
to the Marvell MV88E617x. This takes care of configuring the minimum
amount out of the switch hardware such that each user visible port
(configurable) and the CPU port can forward packets between each other
while preserving isolation with other ports.
This is useful for e.g: the Lamobo R1 board featuring a Broadcom
BCM53125 switch.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This implementation manages several clocks, disable and
free all of them in case of error during probe and in remove
callback.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch fixes a problem in the mvneta driver where if more than
one packet arrives between calls to mvneta_recv(), the additional
descriptors will be marked as free even though only one descriptor
has been read and processed from the receive queue. This causes
the additional packet(s) to be delayed until the next packet arrives.
>From this point on all packets will be delayed because the receive
queue will contain unprocessed packets but the hardware shows no
busy descriptors.
Signed-off-by: Jason Brown <jason.brown@apcon.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Since the return value is a signed int, if the leading MSB of rdreg is a 1,
it will get signed extended and will return a negative value which is an
error even though we read the correct value.
Fixes: dfcc496ed7 ("net: mii: Changes not made by spatch")
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
First, this table could never be included in the build anyway because
SH_ETH_TYPE_RZ is not defined until later in the file.
Second, the register PIR was missing, so PHY MDIO never worked.
Third, after adding the PIR register, the table is EXACTLY the same as
sh_eth_offset_gigabit, so there is no value to it.
Therefore, just delete it use the gigabit one.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The macros inl and outl maybe already be defined from file
arch/arm/include/asm/io.h so there may be no reason to define them.
And if you do try defined them here, you get a redefined complier warning.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This commit allows extended Marvell registers to be read with:
foo > mdio rx FEC 3.10
Reading from bus FEC
PHY at address 0:
3.16 - 0x1063
foo > mdio wx FEC 3.10 0x1011
The above code changes the way ETH connector LEDs blink.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: York Sun <york.sun@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Although Xilinx Zynq SoC was using MACB similar hardware. However,
U-boot MACB driver was not supporting Xilinx Zynq SoC. This patch is
to add support for the Xilinx Zynq SoC to the existing MACB network
driver.
This patch is to add Zynq GEM DMA Config, provide callback
function for different linkspeed for case of using Xilinx Zynq
Programmable Logic as GMII to RGMII converter.
This patch convert the return value to use error codes.
Signed-off-by: Wilson Lee <wilson.lee@ni.com>
Cc: Chen Yee Chew <chen.yee.chew@ni.com>
Cc: Keng Soon Cheah <keng.soon.cheah@ni.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The CONFIG_SYS_DPAA_QBMAN define is used by DPAA1 freescale SOCs to
add device tree fixups that allow deep sleep in Linux. The define was
placed in header files included by a number of boards, but was not
explicitly documented in any of the Kconfigs. A description was added
to the drivers/networking menuconfig and default selection for
current SOCs that have this part
Signed-off-by: Ahmed Mansour <ahmed.mansour@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Until now, Armada 3700 SoCs could not enable the mvneta driver, and thus
did not benefit from Ethernet support. Add ARMADA_3700 in the
"depends on" list of the MVNETA Kconfig entry.
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch is ported from the Linux patch posted at [1] and applied to
net tree as commit f1e2400a80ff.
The purpose of this change is to fix the incorrect detection of the link
partner (LP) advertised capabilities which sometimes happens with this PHY
(roughly 1 time in a dozen)
This issue may cause the link to be negotiated at 10Mbps/Full or
10Mbps/Half when 100MBps/Full is actually possible. In some case, the link
is even completely broken and no communication is possible.
To detect the corruption, we must look for a magic undocumented bit in the
WOL bank (hint given by the SoC vendor kernel) but this is not enough to
cover all cases. We also have to look at the LPA ack. If the LP supports
Aneg but did not ack our base code when aneg is completed, we assume
something went wrong.
The detection of a corrupted LPA triggers a restart of the aneg process.
This solves the problem but may take up to 6 retries to complete.
[1] https://lkml.kernel.org/r/20171208110811.30789-1-jbrunet@baylibre.com
Fixes: 8995a96d1d ("net: phy: Add Amlogic Meson GXL Internal PHY support")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Check LS1043A/LS2080a by device ID without using personality ID to
determine revision number. This check applies to all various
personalities of the same SoC family.
Signed-off-by: Wenbin Song <wenbin.song@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add new compatible to the Ethernet AVB driver for R8A77995 D3 SoC.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add new compatible to the Ethernet AVB driver for R8A77970 V3M SoC.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
>From revision J the board uses new phy chip LAN8710. Compared
with RTL8201, RA17 pin is TXERR. It has pullup which causes phy
not to work. To fix this PA17 is muxed with GMAC function. This
makes the pin output-low.
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
For case when MC is loaded but DPL is not deployed perform MC
object [DPBP, DPIO, DPNI and DPRC] cleanup.
Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Existing MC driver framework is based on MC-9.x.x flib. This patch
migrates MC obj (DPBP, DPNI, DPRC, DPMAC etc) to use latest MC flib
which is MC-10.3.0.
Changes introduced due to migration:
1. To get OBJ token, pair of create and open API replaces create APIs
2. Pair of close and destroy APIs replaces destroy APIs
3. For version read, get_version APIs replaces get_attributes APIs
4. dpni_get/reset_statistics APIs replaces dpni_get/set_counter APIs
5. Simplifies struct dpni_cfg and removes dpni_extended_cfg struct
6. Single API dpni_get_buffer_layout/set_buffer_layout replaces
dpni_get_rx/set_rx, tx related, tx_conf_buffer_layout related APIs.
New API takes a queue type as an argument.
7. Similarly dpni_get_queue/set_queue replaces
dpni_get_rx_flow/set_rx_flow , tx_flow related, tx_conf related
APIs
Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Fix handling of the reset GPIO. Drop the _nodev() suffix from the
gpio_request_by_name() call as there is now a proper DM capable
GPIO driver. Also check if the GPIO is valid before freeing it in
remove path, otherwise U-Boot will crash.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This patch uses readl and writel instead of in_be32 and
out_be32 for io ops as these internally uses readl,
writel for microblaze and for Zynq, ZynqMP there is
no need of endianness conversion and readl, writel
should work straightaway. This patch starts supporting
the driver for Zynq and ZynqMP platforms.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Dont enable SGMII and PCS selection if internal PCS/PMA
is not used, by getting the info about internal/external
PCS/PMA usage from dt property "is-internal-phy".
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for non processor mode, this mode doesn't have
access to some of the registers and hence this patch
bypasses it and also length has to be calculated from
status instead of app4 in this mode.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Read dma address using fdtdec_get_addr as it checks for
address cells and size cells and reads the address
properly. fdtdec_get_int always assume address is of int
size which goes wrong if using it on 64-bit architecture.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The Amlogic Meson GXL/GXM families embeds an internal RMII Ethernet PHY.
The PHY acts as a generic PHY but needs a slight configuration right
before it's configuration.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Value provided in MC_MEM_SIZE_ENV_VAR is in hex. Use 16 as base
in simple_strtoul.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The zero value returned from qbman_swp_acquire() is an error
condition meaning no free buffer for allocation.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Kushwaha Prabhakar <prabhakar@freescale.com>
[YS: revised commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
Only the H3/H5 SoCs have an internal PHY and its related clock and
reset controls.
Use an #ifdef to guard the internal PHY control code block so it
can be built for other SoCs, such as the A83T or A64.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
due misnaming of CONFIG_SUN4I_EMAC in include/configs/sunxi-common.h,
likely missed in:
commit 3146f0c017 ("Move PHYLIB to Kconfig")
Signed-off-by: Artturi Alm <artturi.alm@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
As reported by Jonathan Gray:
"After the recent changes to add SimpleNetworkProtocol to efi_loader
when booting off mmc via an efi payload that doesn't use
SimpleNetworkProtocol U-Boot's fec_mxc driver will now display
various "error frame" messages.
....
MMC Device 1 not found
MMC Device 2 not found
MMC Device 3 not found
Scanning disks on sata...
Found 6 disks
reading efi/boot/bootarm.efi
67372 bytes read in 32 ms (2 MiB/s)
## Starting EFI application at 12000000 ...
>> OpenBSD/armv7 BOOTARM 1.0
error frame: 0x8f57ec40 0x00003d74
error frame: 0x8f57ec40 0x00007079
error frame: 0x8f57ec40 0x00006964
error frame: 0x8f57ec40 0x00006f6f
error frame: 0x8f57ec40 0x0000726f
error frame: 0x8f57ec40 0x00002074
error frame: 0x8f57ec40 0x00006f6f"
Heinrich Schuchardt explains:
"A receive FIFO overrun can be expected if network packages are not
processed.
With the network patches we check if a package is available quite often."
Move the "error frame" messages to debug level so that a clean output
log can be seen.
Reported-by: Jonathan Gray <jsg@jsg.id.au>
Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Since TX delay is now enabled only in PHY_INTERFACE_MODE_RGMII_ID
PHY_INTERFACE_MODE_RGMII_TXID.
These change where introduced in phy driver in commit 05b29aa0cb
("net: phy: realtek: fix enabling of the TX-delay for RTL8211F").
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Memory allocated via malloc is not guaranteed to be zeroized.
So explicitly use calloc instead of malloc.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
We add the various SMC91XX symbols to drivers/net/Kconfig and then this
converts the following to Kconfig:
CONFIG_SMC911X
CONFIG_SMC911X_BASE
CONFIG_SMC911X_16_BIT
CONFIG_SMC911X_32_BIT
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Apply to the rest of the tree, re-squash old and new patch]
Signed-off-by: Tom Rini <trini@konsulko.com>
U-Boot widely uses error() as a bit noisier variant of printf().
This macro causes name conflict with the following line in
include/linux/compiler-gcc.h:
# define __compiletime_error(message) __attribute__((error(message)))
This prevents us from using __compiletime_error(), and makes it
difficult to fully sync BUILD_BUG macros with Linux. (Notice
Linux's BUILD_BUG_ON_MSG is implemented by using compiletime_assert().)
Let's convert error() into now treewide-available pr_err().
Done with the help of Coccinelle, excluing tools/ directory.
The semantic patch I used is as follows:
// <smpl>
@@@@
-error
+pr_err
(...)
// </smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Re-run Coccinelle]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_MVNETA
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Add support for obtaining PHY reset GPIO from DT and toggling it
before configuring the PHY to put the PHY into defined state.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Update the Micrel KSZ90x1 driver for a live tree.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Update the Designware Ethernet MAC driver to support a live device
tree.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
All these places seem to inherit the codes from the MMC driver where
a FIXME was put in the comment. However the correct operation after
read should be cache invalidate, not flush.
The underlying drivers should be responsible for the cache operation.
Remove these codes completely.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: York Sun <york.sun@nxp.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: York Sun <york.sun@nxp.com>
This patch adds support for RGMII protocol
NXP's LDPAA2 support RGMII protocol. LS1088A is the
first Soc supporting both RGMII and SGMII.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Amrita Kumari <amrita.kumari@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Update MC address calculation as per MC design requirement of address
as least significant 512MB address of MC private allocated memory,
i.e. address should point to end address masked with 512MB offset in
private DRAM block.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Ashish Kumar <ashish.kumar@nxp.com>
[YS: reformatted commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
The old logic always enabled the TX-delay when the phy-mode was set to
PHY_INTERFACE_MODE_RGMII. With this patch we enable the TX delay for
PHY_INTERFACE_MODE_RGMII_ID and PHY_INTERFACE_MODE_RGMII_TXID and
disable it for PHY_INTERFACE_MODE_RGMII.
Based on a similar change made in the Linux Realtek PHY driver
by Martin Blumenstingl <martin.blumenstingl@googlemail.com>.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: York Sun <york.sun@nxp.com>
We are now using an env_ prefix for environment functions. Rename these
other functions as well, for consistency:
getenv_vlan()
getenv_bootm_size()
getenv_bootm_low()
getenv_bootm_mapsize()
env_get_default()
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
We are now using an env_ prefix for environment functions. Rename these
two functions for consistency. Also add function comments in common.h.
Quite a few places use getenv() in a condition context, provoking a
warning from checkpatch. These are fixed up in this patch also.
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
We are now using an env_ prefix for environment functions. Rename these
commonly used functions, for consistency. Also add function comments in
common.h.
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
We are now using an env_ prefix for environment functions. Rename setenv()
for consistency. Also add function comments in common.h.
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
Even after memory free of phydev, priv is still pointing to the
obsolete address.
So update priv->phydev as NULL after memory free.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The GMAC in the RK3368 once again is identical to the incarnation in
the RK3288 and the RK3399, except for where some of the configuration
and control registers are located in the GRF.
This adds the RK3368-specific logic necessary to reuse this driver.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Set BM poll size once during priv probe and do not
overwrite it during port probe procedure. Pool is common for
all CP ports.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Tested-by: iSoC Platform CI <ykjenk@marvell.com>
Reviewed-by: Nadav Haklai <nadavh@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Stefan Roese <sr@denx.de>
TX drain in transmit procedure could cause issues due
to race between drain procedure and transmition of descriptor
between AGGR TXQ and physical TXQ.
TXQ will be cleared before moving to Linux by stop procedure.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Tested-by: iSoC Platform CI <ykjenk@marvell.com>
Reviewed-by: Nadav Haklai <nadavh@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Stefan Roese <sr@denx.de>
MVPP22 driver support 64 Bit arch and require BM pool
high address configuration.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Tested-by: iSoC Platform CI <ykjenk@marvell.com>
Reviewed-by: Nadav Haklai <nadavh@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Remove IRQ configuration from U-Boot PP driver.
U-Boot don't use interrupts and configuration of IRQ in U-Boot
caused crashes in Linux shared interrupt mode.
Also interrupt use is redundant in RX routine since a single RX
queue is used.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Tested-by: iSoC Platform CI <ykjenk@marvell.com>
Reviewed-by: Nadav Haklai <nadavh@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Stefan Roese <sr@denx.de>
MBUS driver were replaced by AXI in PPv22 and relevant
only for PPv21.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Tested-by: iSoC Platform CI <ykjenk@marvell.com>
Reviewed-by: Nadav Haklai <nadavh@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Stefan Roese <sr@denx.de>
U-boot use single physical tx queue with size 16 descriptors.
So aggregated tx queue size should be equal to physical tx queue
and cpu descriptor chunk(number of descriptors delivered from
physical tx queue to aggregated tx queue by one chunk) shouldn't be
larger than physical tx queue.
Fix:
Set AGGR_TXQ and CPU_DESC_CHUNK to be 16 descriptors, same as
physical TXQ.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Tested-by: iSoC Platform CI <ykjenk@marvell.com>
Reviewed-by: Nadav Haklai <nadavh@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Issue:
BM counters were overrun by probe that called per Network interface and
caused release of wrong number of buffers during remove procedure.
Fix:
Use probe_done and num_ports to call init and remove procedure
once per communication controller.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Tested-by: iSoC Platform CI <ykjenk@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch enables padding of packets shorter than 64B in TX(set by default).
Disabling of padding causes crashes on MACCIATO board.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Tested-by: iSoC Platform CI <ykjenk@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Stefan Roese <sr@denx.de>
A8K marvell SoC has two South Bridge communication controllers(CP0 and CP1).
Each communication controller has packet processor ports and MDIO.
On MACHIATOBin board ports from CP1 are connected to mdio on CP0.
Issue:
Wrong base address is assigned to MDIO interface during probe.
Fix:
Get MDIO address from PHY handler parent base address.
This should be refined in the future when MDIO driver is implemented.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Tested-by: iSoC Platform CI <ykjenk@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch add GPIO configuration support in mvpp2x driver.
Driver will handle 10G SFP gpio reset and SFP TX disable. GPIO pins should
be set in device tree.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Tested-by: iSoC Platform CI <ykjenk@marvell.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Stefan Roese <sr@denx.de>
In fsl_mc_ldpaa_exit(), in case of mc is booted and dpl is applied,
it should return earlier without executing dpbp_exit().
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Acked-by: Priyanka Jain <priyanka.jain@nxp.com>
Acked-by: Yogesh Narayan Gaur <yogeshnarayan.gaur@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The environment variable "disable_giga" can now be used to disable
1000baseTx on the Micrel's KSZ9031.
Signed-off-by: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Added the AFE (Analog Front End) settings for stability to the
Broadcom Cygnus phy. This improves the time take to perform
auto negotiation.
Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
move to Kconfig:
CONFIG_BCM_SF2_ETH
CONFIG_BCM_SF2_ETH_DEFAULT_PORT
CONFIG_BCM_SF2_ETH_GMAC
Also modified defconfigs of all platforms that use these configs.
Signed-off-by: Suji Velupillai <suji.velupillai@broadcom.com>
Tested-by: Suji Velupillai <suji.velupillai@broadcom.com>
Reviewed-by: JD Zheng <jiandong.zheng@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Steve Rae <steve.rae@raedomain.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The correct option is PHY_MICREL_KSZ90X1, but some configs still
select the 9021 and 9031 options, which are deprecated.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
There should be no longer be any ksz9000 users that pick up the PHY
driver from ksz8xxx, so remove ksz9000 remnants from there.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The KS8721BL and KSZ9021 PHYs are software-incompatible, yet they
share the same ID. Drivers for bothe PHYs cannot safely coexist, so
the solution was to use #ifdefs to select between the two drivers.
As a result KSZ9031, which has a unique ID, is now caught in the
crossfire. Unless CONFIG_PHY_MICREL_KSZ9031 is defined, the KSZ9031
will not function properly, as some essential configuration code is
ifdef'd-out.
To prevent such situations, move the KSZ9000 drivers to a separate
file, and place them under a separate Kconfig option. While it is
possible to enable both KSZ8000 and KSZ9000 drivers at the same time,
the assumption is that it is highly unlikely for a system to contain
both a KSZ8000 and a KSZ9000 PHY, and that only one of the drivers
will be enabled at any given time.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The register constants don't use the exact names that are used in the
TRM, so add comments that use the exact names so that it is clear what
register is being referred to.
https://www.atheros-drivers.com/qualcomm-atheros-datasheets-for-AR9331.html
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Marek Vasut <marex@denx.de>
phy_device_create(..) sets the addr of phy_device with a sane value.
There is no need overwrite it.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Tested-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add support for enabling and disabling the clock using the clock
framework based on the content of OF instead of doing it manually
in the board file.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The order of parameters passed to the phy_connect() was wrong.
Moreover, only PHY address 0 was used. Replace this with code
capable of detecting the PHY address.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add support for probing the RAVB Ethernet block from device tree.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
commit 306dd7dabd ("net: fec_mxc: fix PHY initialization bug with CONFIG_DM_ETH")
has broken the build of the fec_mxc driver with CONFIG_DM_ETH
enabled because it changed the parameters passed to *fec_get_miibus()
without changing the functions prototype.
This patch fixes up the prototype of fec_get_miibus() for the DM_ETH case.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Add missing .h and add missing declarations in .h
Declare local functions as static. Make interrupt_init_cpu function
signatures consistent with how decrementer_count is declared.
Based on warnings reported by 'make C=2'
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
[trini: drop cpu_init_f as 8xx/83xx are different from the rest, rework
interrupt_init_cpu/decrementer_count]
Signed-off-by: Tom Rini <trini@konsulko.com>
Change is consistent with other SOCs and it is in preparation
for adding SOMs. SOC's related files are moved from cpu/ to
mach-imx/<SOC>.
This change is also coherent with the structure in kernel.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@nxp.com>
CC: Akshay Bhat <akshaybhat@timesys.com>
CC: Ken Lin <Ken.Lin@advantech.com.tw>
CC: Marek Vasut <marek.vasut@gmail.com>
CC: Heiko Schocher <hs@denx.de>
CC: "Sébastien Szymanski" <sebastien.szymanski@armadeus.com>
CC: Christian Gmeiner <christian.gmeiner@gmail.com>
CC: Stefan Roese <sr@denx.de>
CC: Patrick Bruenn <p.bruenn@beckhoff.com>
CC: Troy Kisky <troy.kisky@boundarydevices.com>
CC: Nikita Kiryanov <nikita@compulab.co.il>
CC: Otavio Salvador <otavio@ossystems.com.br>
CC: "Eric Bénard" <eric@eukrea.com>
CC: Jagan Teki <jagan@amarulasolutions.com>
CC: Ye Li <ye.li@nxp.com>
CC: Peng Fan <peng.fan@nxp.com>
CC: Adrian Alonso <adrian.alonso@nxp.com>
CC: Alison Wang <b18965@freescale.com>
CC: Tim Harvey <tharvey@gateworks.com>
CC: Martin Donnelly <martin.donnelly@ge.com>
CC: Marcin Niestroj <m.niestroj@grinn-global.com>
CC: Lukasz Majewski <lukma@denx.de>
CC: Adam Ford <aford173@gmail.com>
CC: "Albert ARIBAUD (3ADEV)" <albert.aribaud@3adev.fr>
CC: Boris Brezillon <boris.brezillon@free-electrons.com>
CC: Soeren Moch <smoch@web.de>
CC: Richard Hu <richard.hu@technexion.com>
CC: Wig Cheng <wig.cheng@technexion.com>
CC: Vanessa Maegima <vanessa.maegima@nxp.com>
CC: Max Krummenacher <max.krummenacher@toradex.com>
CC: Stefan Agner <stefan.agner@toradex.com>
CC: Markus Niebel <Markus.Niebel@tq-group.com>
CC: Breno Lima <breno.lima@nxp.com>
CC: Francesco Montefoschi <francesco.montefoschi@udoo.org>
CC: Jaehoon Chung <jh80.chung@samsung.com>
CC: Scott Wood <oss@buserror.net>
CC: Joe Hershberger <joe.hershberger@ni.com>
CC: Anatolij Gustschin <agust@denx.de>
CC: Simon Glass <sjg@chromium.org>
CC: "Andrew F. Davis" <afd@ti.com>
CC: "Łukasz Majewski" <l.majewski@samsung.com>
CC: Patrice Chotard <patrice.chotard@st.com>
CC: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CC: Hans de Goede <hdegoede@redhat.com>
CC: Masahiro Yamada <yamada.masahiro@socionext.com>
CC: Stephen Warren <swarren@nvidia.com>
CC: Andre Przywara <andre.przywara@arm.com>
CC: "Álvaro Fernández Rojas" <noltari@gmail.com>
CC: York Sun <york.sun@nxp.com>
CC: Xiaoliang Yang <xiaoliang.yang@nxp.com>
CC: Chen-Yu Tsai <wens@csie.org>
CC: George McCollister <george.mccollister@gmail.com>
CC: Sven Ebenfeld <sven.ebenfeld@gmail.com>
CC: Filip Brozovic <fbrozovic@gmail.com>
CC: Petr Kulhavy <brain@jikos.cz>
CC: Eric Nelson <eric@nelint.com>
CC: Bai Ping <ping.bai@nxp.com>
CC: Anson Huang <Anson.Huang@nxp.com>
CC: Sanchayan Maity <maitysanchayan@gmail.com>
CC: Lokesh Vutla <lokeshvutla@ti.com>
CC: Patrick Delaunay <patrick.delaunay@st.com>
CC: Gary Bisson <gary.bisson@boundarydevices.com>
CC: Alexander Graf <agraf@suse.de>
CC: u-boot@lists.denx.de
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
When CONFIG_DM_ETH is set, the FEC ethernet controller is reset after
the PHY has been set up and initialzed. This breaks the communication
with the PHY and results in an inoperable ethernet interface.
Do the initialization with CONFIG_DM_ETH in the same order as with
legacy ETH support to fix this.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
As part of preparation for nand DM conversion the new API has been
introduced to remove direct access to nand_info array. So, use it here
instead of accessing to nand_info array directly.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
As part of preparation for nand DM conversion the new API has been
introduced to remove direct access to nand_info array. So, use it here
instead of accessing to nand_info array directly
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
With the new dev_read functions available, we can convert the rockchip
architecture-specific drivers and common drivers used by these devices
over to the dev_read family of calls.
This covers the Gigabit Ethernet MAC (i.e. common designware driver and
rockchip-specific wrapper).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
CS Systemes d'Information (CSSI) manufactures two boards, named MCR3000
and CMPC885 which are respectively based on MPC866 and MPC885 processors.
This patch adds support for the first board.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
There was for long time no activity in the 4xx area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in 4xx,
so remove it.
Signed-off-by: Heiko Schocher <hs@denx.de>
The ti816x SoC revision of the ethernet IP block is handled by the
"davinci_emac" driver, rather than the "cpsw" driver as done by later
members of the family. Enable the relevant plumbing.
Signed-off-by: Sriramakrishnan <srk@ti.com>
Signed-off-by: Vitaly Wool <vitaly.wool@konsulko.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
There was for long time no activity in the mpx5xxx area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in mpc5xxx,
so remove it.
Signed-off-by: Heiko Schocher <hs@denx.de>
Commit a058052c changed the generic phy_reset() to clear all bits in
BMCR. This inevitably clears the ANEG bit. m88e1145 requires any
change to ANEG bit to be followed by a software reset. This seems to
be different from other PHYs. Implement read-modify-write procedure
for this PHY init.
Signed-off-by: York Sun <york.sun@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
There was for long time no activity in the 8xx area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in 8xx,
so remove it (with a heavy heart, knowing that I remove
here the root of U-Boot).
Signed-off-by: Heiko Schocher <hs@denx.de>
The declarations should not be in common.h. Move them to the arch-specific
headers.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Fixup thinko defined(FSL_LSCH3) -> defined(CONFIG_FSL_LSCH3)]
Signed-off-by: Tom Rini <trini@konsulko.com>
On MIPS systems DMA isn't coherent with the CPU caches unless an IOCU is
present. When there is no IOCU we need to writeback or invalidate the
data caches at appropriate points. Perform this cache maintenance in
the pch_gbe driver which is used on the MIPS Boston development board.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Use the virt_to_bus & bus_to_virt functions rather than phys_to_bus &
bus_to_phys, since the addresses accessed by the CPU will be virtual
rather than physical. On MIPS physical & virtual addresses differ as we
use virtual addresses in kseg0, and attempting to use physical addresses
directly caused problems as they're in the user segment which would be
mapped via the uninitialised TLB.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The loop to set up buffer addresses in rx descriptors always operated on
descriptor 0, rather than on each descriptor sequentially. Fix this in
order to setup correct buffer addresses for each descriptor.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Using the EG20T gigabit ethernet controller on the MIPS Boston board, we
find that we have to reset the controller in order for the RGMII link to
the PHY to become functional. Without doing so we constantly time out in
pch_gbe_mdio_ready.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Dont flush dummy descriptors as they are already
allocated from a region with dcache off. Tested
this on Zynq(zc702) and ZynqMP(zcu102) boards.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Use wait_for_bit to be non breakable as using it with
breakable causes issue of un interruptible auto negotiation.
This is due to the ctrlc pressed will taken for wait_for_bit()
abort during phy_read() and hence not coming out of
auto negotiation.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The 88E1518 code is programming the wrong registers for rgmii-id,
rgmii-txid and rgmii-rxid interfaces.
Since the PHY defaults to rgmii-id, it would appear that the code
was previously only used with sgmii and rgmii-id interfaces.
Tested on 88E1512 PHY in rgmii-id mode which is from the same family
as 88E1518.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Abort CPSW driver init when auto-negotiation of link
times out. Currently, the code ignores return status
of phy_startup(), and goes ahead with network operation
(like DHCP) even though the link may be down.
Instead, abort init process if link is down or if there
is another error, so phy_startup() can easily be retried
again. This also helps quick fallback to next network interface
(like USB RNDIS) without inordinate delay.
Tested on AM571x IDK and AM335x BeagleBone black.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Always search the PHY to determine the macb->phy_addr before using
the PHY to fix "No PHY present" error.
Fix the wrong test of the GMAC's phy interface mode, it should be
PHY_INTERFACE_MODE_RGMII.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch fixes some remaining issues in the mvpp2 driver for the 10GB
support on port 0. These changes are:
- Incorrect PCS configuration
- Skip PHY configuration when no PHY is connected
- Skip GMAC configurations if 10G SFI mode set
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The .read_rom_hwaddr net_ops hook does not check the return value, which
is why it was never caught that we are currently returning 0 if the
read_rom_hwaddr function return -ENOSYS and -ENOSYS otherwise.
In this case we can simplify this by just returning the result of the
function.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Some board need a regulator for gmac phy, so add this code to handle it.
Signed-off-by: Jacob Chen <jacob2.chen@rock-chips.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This change migrate the following configuration options for Kconfig:
* PHY_GIGE, indicates that a controller (with an appropriate PHY) is
Gigabit capable and enables extra support in the miiutil for
parsing the status of Gigabit PHYs
* adds configuration options for Micrel KSZ9021 and KSZ9031 GbE PHYs,
which previously had to enabled through a board-specific config file
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Previous to MC v10.x, port mac address was specified via DPL. Since
newer MC versions are compatible with old style DPLs, make the u-boot
env mac addresses visible there. This applies only to DPLs that have
an older version.
DPLs use 32 bit values for specifying MAC addresses. U-boot
environment variables take precedence over the MAC addresses already
visible in the DPL/DPC.
Signed-off-by: Bogdan Purcareata <bogdan.purcareata@nxp.com>
Signed-off-by: Heinz Wrobel <heinz.wrobel@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
DPAA2 platforms boot the Management Complex based on the u-boot env
variable "mcinitcmd". Instead of doing this step on each platform
individually, define a single mc_env_boot function in the MC driver,
since it's semantically tied to it.
Call the function in a per-board reset_phy hook, as it gets called at a
later moment, when all board PHY devices have been initialized.
Signed-off-by: Bogdan Purcareata <bogdan.purcareata@nxp.com>
Signed-off-by: Heinz Wrobel <heinz.wrobel@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
These two functions have an of_ prefix which conflicts with naming used
in of_addr. Rename them:
fdt_read_number
fdt_support_bus_default_count_cells
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for requesting GPIOs with a live device tree.
This involves adjusting the function signature for the legacy function
gpio_request_by_name_nodev(), so fix up all callers.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes to stm32f746-disco.c:
Signed-off-by: Tom Rini <trini@konsulko.com>
Adjust this function to us an ofnode instead of an offset, so it can be
used with livetree. This involves updating all callers.
Signed-off-by: Simon Glass <sjg@chromium.org>
The of_ prefix conflicts with the livetree version of this function.
Rename it to avoid problems when we add livetree support.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present devices use a simple integer offset to record the device tree
node associated with the device. In preparation for supporting a live
device tree, which uses a node pointer instead, refactor existing code to
access this field through an inline function.
Signed-off-by: Simon Glass <sjg@chromium.org>
These support the flat device tree. We want to use the dev_read_..()
prefix for functions that support both flat tree and live tree. So rename
the existing functions to avoid confusion.
In the end we will have:
1. dev_read_addr...() - works on devices, supports flat/live tree
2. devfdt_get_addr...() - current functions, flat tree only
3. of_get_address() etc. - new functions, live tree only
All drivers will be written to use 1. That function will in turn call
either 2 or 3 depending on whether the flat or live tree is in use.
Note this involves changing some dead code - the imx_lpi2c.c file.
Signed-off-by: Simon Glass <sjg@chromium.org>
This header includes things that are needed to make driver build. Adjust
existing users to include that always, even if other dm/ includes are
present
Signed-off-by: Simon Glass <sjg@chromium.org>
Earlier when MC is loaded but DPL is not deployed results in FDT
fix-up code execution hangs. For this case now print message on
console and return success instead of return -ENODEV. This update
allows fdt fixup to continue execution.
Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
Signed-off-by: Priyanka Jain <Priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add driver for the Renesas Ethernet AVB block found in RCar H3/M3.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Tom Rini <trini@konsulko.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Based on work of:
Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Takeshi Kihara <takeshi.kihara.df@renesas.com>
Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Specify the registered eth index by dev_id.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Avoid transfer parameter dev_id value with "-1" to .fec_get_hwaddr(),
it should transfer fec->dev_id to get mac address from fuse.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Stefano Babic <sbabic@denx.de>
The MIB RAM and FIFO receive start register does not exist on
i.MX6ULL. Accessing these register will cause enet not work well or
cause system report fault.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
The variable netdev_ethtool_ops is not referenced, drop it. However
with gcc-6 or later we fail to even compile as we do not have the
required struct definition in U-Boot.
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The variable 'res' may be unused uninitialized if our call to
mv88e61xx_port_read (register read) fails and we goto the error
handling section. In this case we set 'res' to -EIO to indicate why we
failed.
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Chris Packham <judge.packham@gmail.com>
Cc: Kevin Smith <kevin.smith@elecsyscorp.com>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
To avoid the failure of mdio_register(), add the remove callback
to unregister the mii_dev when removing the ethernet device.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Fixed up unused variable warning, e.g. for gurnard:
Signed-off-by: Simon Glass <sjg@chromium.org>
This patch adds a remove function to the mvpp2 ethernet driver which is
called before the OS is started, doing:
- Allocate the used buffers back from the buffer manager
- Stop the BM activity
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefan Chulski <stefanc@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Convert CONFIG_RGMII to Kconfig. Thanks to that, it is possible to
update defconfig files of SYS_EXTRA_OPTIONS accordingly and
remove it when it is possible.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Convert the SUNXI_EMAC config to Kconfig. Remove it from SYS_EXTRA_OPTIONS
from many sunxi defconfig and renamed it into SUN4I_EMAC to not confuse it
with SUN8I_EMAC.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Move the SUNXI_GMAC config option to Kconfig, remove it
from SYS_EXTRA_OPTIONS and rename it into SUN7I_GMAC.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
These drivers have no user since commit ea3310e8aa ("Blackfin:
Remove").
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
The intention of the removal is the preparation to introduce the
new AT91 PIO pinctrl driver.
Use the union to make the PIO3 and PIO2's registers be together
and make their offset aligned.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This ports the support for configuring a GPIO for resetting the
Ethernet PHY (incl. such details as the reset polarity and
pulse-length) from the Designware driver.
X-AffectedPlatforms: A64-uQ7
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
With d53ecad92f some unused interrupt related code was removed.
However all of these options are currently unused. Rather than migrate
some of these options to Kconfig we just remove the code in question.
The only related code changes here are that in some cases we use
CONFIG_STACKSIZE in non-IRQ related context. In these cases we rename
and move the value local to the code in question.
Fixes: d53ecad92f ("Merge branch 'master' of git://git.denx.de/u-boot-sunxi")
Signed-off-by: Tom Rini <trini@konsulko.com>
The Allwinner H5 is very close to the H3 SoC, but has ARMv8 cores.
To allow sharing the clocks, GPIO and driver code easily, create an
architecture agnostic MACH_SUNXI_H3_H5 Kconfig symbol.
Rename the existing symbol to MACH_SUNXI_H3_H5 where code is shared and
let it be selected by a new shared Kconfig option.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The GMAC in the RK3399 is very similar to the RK3288 variant (i.e. it
is a Designware GMAC core and requires similar configuration as the
RK3288 to switch it to RGMII and set up the TX/RX delays for Gigabit).
The key difference is that the register offsets (within the GRF block)
and bit-offsets (within those registers) used to hold the configuration
differ between the various RK32/33 CPUs.
This change refactors the gmac_rockchip.c driver to use a function
table (selected via driver_data) to factor out these differences. Each
function's implementation then matches the underlying processor.
Some collateral changes are needed in the definitions describing the
bits and offsets in the GRF are needed to prefix each set of symbolic
constants with the SoC name to avoid name clashes... and in doing so,
the shifts for masks and constants have been moved into the header
files for readability (and to make it easier to stay below 80 chars).
X-AffectedPlatforms: RK3399-Q7
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Fixed commit message typo s/factor our/factor out/:
Signed-off-by: Simon Glass <sjg@chromium.org>
This includes Marvell mvpp2 patches with the ethernet support for the
ARMv8 Armada 7k/8k platforms. The ethernet patches are all acked by Joe
and he is okay with me pushing them via the Marvell tree.
As pointed out by Stefan Chulski, this variable is unused and should be
removed.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefan Chulski <stefanc@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
On PPv2.2 we enable PHY polling, so we also need to configure the PHY
address in the specific PHY address rgisters.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefan Chulski <stefanc@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Testing shows, that PHY polling needs to be enabled on Armada 7k/8k.
Otherwise ethernet transfers will not work correctly. PHY polling
is enabled per default after reset, so we do not need to specifically
enable it, but this makes it clearer.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefan Chulski <stefanc@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add a missing occurrance of PHY_INTERFACE_MODE_RGMII_ID, which should
be handled identical to PHY_INTERFACE_MODE_RGMII.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefan Chulski <stefanc@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch adds the GoP (Group of Ports) and NetC (Net Complex) setup to
the Marvell mvpp2 ethernet driver for the missing port 0. This code is
mostly copied from the Marvell U-Boot version and was written by Stefan
Chulski. Please note that only SFI support have been added, as this
is the only interface that this code has been tested with. XAUI and
RXAUI support might follow at a later stage.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefan Chulski <stefanc@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch adds the GoP (Group of Ports) and NetC (Net Complex) setup to
the Marvell mvpp2 ethernet driver. This code is mostly copied from the
Marvell U-Boot version and was written by Stefan Chulski. Please
note that only RGMII and SGMII support have been added, as these are
the only interfaces that this code has been tested with.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefan Chulski <stefanc@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Read the "phy-speed" DT property to differentiate between 1 and 2.5GB
SGMII operations. Please note that its unclear right now, if this
DT property will be accepted in mainline Linux. If not, we need to
revisit this code and change it to use the accepted property.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch does a bit of restructuring of the probe / init functions,
mainly to allow earlier register access as it is needed for the upcoming
GoP (Group of Ports) and NetC (Net Complex) code.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch adds the PPv2.2 specific FIFO configuration to the mvpp2
driver. The RX FIFO packet data size is changed to the recommended
FIFO sizes. The TX FIFO configuration is newly added.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefan Chulski <stefanc@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Currently, the naming of the ethernet ports is not handled correctly in
the multi-CP (Communication Processor) case. On Armada 8k, the slave-CP
also instantiates an ethernet controller with the same device ID's.
This patch now takes this into account and adds the required base-id
so that the slave-CP ethernet devices will be named "mvpp2-3 ...".
This patch also updates my Copyright notice to include 2017 as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefan Chulski <stefanc@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Since Armada 7K/8K is also equipped with a newer version of the MVPP2
ethernet controller, lets enable compilation of this driver for these
platforms.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This fixes problems noticed with the PPv2.2 A7k/8k port, when not all
elements of the descriptors had been cleared before use.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch moves the base_probe function mvpp2_base_probe() from the
MISC driver to the ETH driver. When integrated in the MISC driver,
probe is called too early before the U-Boot ethernet infrastructure
(especially the MDIO / PHY interface) has been initialized. Resulting
in errors in mdio_register().
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
In U-Boot the MDIO / SMI support is integrated in the mvpp2 driver,
currently only supporting the 32bit platforms (Armada 37x). This patch
now adds the A7k/8k PPv2.2 MDIO support to that the phy / mii IF
can be used as well on these platforms.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Now that the mvpp2 driver has been modified to accommodate the support
for PPv2.2, we can finally advertise this support by adding the
appropriate compatible string.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
In PPv2.1, we have a maximum of 8 RXQs per port, with a default of 4
RXQs per port, and we were assigning RXQs 0->3 to the first port, 4->7
to the second port, 8->11 to the third port, etc.
In PPv2.2, we have a maximum of 32 RXQs per port, and we must allocate
RXQs from the range of 32 RXQs available for each port. So port 0 must
use RXQs in the range 0->31, port 1 in the range 32->63, etc.
This commit adapts the mvpp2 to this difference between PPv2.1 and
PPv2.2:
- The constant definition MVPP2_MAX_RXQ is replaced by a new field
'max_port_rxqs' in 'struct mvpp2', which stores the maximum number of
RXQs per port. This field is initialized during ->probe() depending
on the IP version.
- MVPP2_RXQ_TOTAL_NUM is removed, and instead we calculate the total
number of RXQs by multiplying the number of ports by the maximum of
RXQs per port. This was anyway used in only one place.
- In mvpp2_port_probe(), the calculation of port->first_rxq is adjusted
to cope with the different allocation strategy between PPv2.1 and
PPv2.2. Due to this change, the 'next_first_rxq' argument of this
function is no longer needed and is removed.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This commit adjusts how the MVPP2_ISR_RXQ_GROUP_REG register is
configured, since it changed between PPv2.1 and PPv2.2.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The PPv2.2 unit is connected to an AXI bus on Armada 7K/8K, so this
commit adds the necessary initialization of the AXI bridge.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This commit handles a few miscellaneous differences between PPv2.1 and
PPv2.2 in different areas, where code done for PPv2.1 doesn't apply for
PPv2.2 or needs to be adjusted (getting the MAC address, disabling PHY
polling, etc.).
Changed by Stefan for U-Boot:
Since mvpp2_port_power_up() has multiple callers in U-Boot, the U-Boot
version of this patch does not remove this function but simply adds the
check for MVPP21 before the mvpp2_port_fc_adv_enable() call.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This commit adjusts the mvpp2 driver register mapping and access logic
to support PPv2.2, to handle a number of differences.
Due to how the registers are laid out in memory, the Device Tree binding
for the "reg" property is different:
- On PPv2.1, we had a first area for the common registers, and then one
area per port.
- On PPv2.2, we have a first area for the common registers, and a
second area for all the per-ports registers.
In addition, on PPv2.2, the area for the common registers is split into
so-called "address spaces" of 64 KB each. They allow to access the same
registers, but from different CPUs. Hence the introduction of cpu_base[]
in 'struct mvpp2', and the modification of the mvpp2_write() and
mvpp2_read() register accessors. For PPv2.1, the compatibility is
preserved by using an "address space" size of 0.
Changed by Stefan for U-Boot:
Since we don't support multiple CPUs in U-Boot, I've removed all the
code, macros and variables introduced in the Linux patch version for this.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
In PPv2.2, the MVPP2_RXQ_DESC_ADDR_REG and MVPP2_TXQ_DESC_ADDR_REG
registers have a slightly different layout, because they need to contain
a 64-bit address for the RX and TX descriptor arrays. This commit
adjusts those functions accordingly.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This commit modifies the mvpp2_defaults_set() function to not do the
loopback and FIFO threshold initialization, which are not needed for
PPv2.2.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The MVPP2_RXQ_CONFIG_REG register has a slightly different layout
between PPv2.1 and PPv2.2, so this commit adapts the functions modifying
this register to accommodate for both the PPv2.1 and PPv2.2 cases.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This commit adjusts the allocation and freeing of BM pools to support
PPv2.2. This involves:
- Checking that the number of buffer pointers is a multiple of 16, as
required by the hardware.
- Adjusting the size of the DMA coherent area allocated for buffer
pointers. Indeed, PPv2.2 needs space for 2 pointers of 64-bits per
buffer, as opposed to 2 pointers of 32-bits per buffer in
PPv2.1. The size in bytes is now stored in a new field of the
mvpp2_bm_pool structure.
- On PPv2.2, getting the physical and virtual address of each buffer
requires reading the MVPP2_BM_ADDR_HIGH_ALLOC to get the high order
bits of those addresses. A new utility function
mvpp2_bm_bufs_get_addrs() is introduced to handle this.
- On PPv2.2, releasing a buffer requires writing the high order 32 bits
of the physical address to MVPP2_BM_PHY_VIRT_HIGH_RLS_REG. We no
longer need to write the virtual address to MVPP2_BM_VIRT_RLS_REG.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This commit adds the definition of the PPv2.2 HW descriptors, adjusts
the mvpp2_tx_desc and mvpp2_rx_desc structures accordingly, and adapts
the accessors to work on both PPv2.1 and PPv2.2.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Since the format of the HW descriptors is different between PPv2.1 and
PPv2.2, this commit introduces an intermediate union, with for now
only the PPv2.1 descriptors. The bulk of the driver code only
manipulates opaque mvpp2_tx_desc and mvpp2_rx_desc pointers, and the
descriptors can only be accessed and modified through the accessor
functions. A follow-up commit will add the descriptor definitions for
PPv2.2.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
In preparation to the introduction for the support of PPv2.2 in the
mvpp2 driver, this commit adds a hw_version field to the struct
mvpp2, and uses the .data field of the DT match table to fill it in.
Having the MVPP21 and MVPP22 definitions available will allow to start
adding the necessary conditional code to support PPv2.2.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The PPv2.2 IP has a different TX and RX descriptor layout compared to
PPv2.1. In order to prepare for the introduction of PPv2.2 support in
mvpp2, this commit adds accessors for the different fields of the TX
and RX descriptors, and changes the code to use them.
For now, the mvpp2_port argument passed to the accessors is not used,
but it will be used in follow-up to update the descriptor according to
the version of the IP being used.
Apart from the mechanical changes to use the newly introduced
accessors, a few other changes, needed to use the accessors, are made:
- The mvpp2_txq_inc_put() function now takes a mvpp2_port as first
argument, as it is needed to use the accessors.
- Similarly, the mvpp2_bm_cookie_build() gains a mvpp2_port first
argument, for the same reason.
- In mvpp2_rx_error(), instead of accessing the RX descriptor in each
case of the switch, we introduce a local variable to store the
packet size.
- Similarly, in mvpp2_buff_hdr_rx(), we introduce a local "cookie"
variable to store the RX descriptor cookie, rather than accessing
it from the descriptor each time.
- In mvpp2_tx_frag_process() and mvpp2_tx() instead of accessing the
packet size from the TX descriptor, we use the actual value
available in the function, which is used to set the TX descriptor
packet size a few lines before.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
As indicated by Russell King, the mvpp2 driver currently uses a lot
"phys" or "phys_addr" to store what really is a DMA address. This commit
clarifies this by using "dma" or "dma_addr" where appropriate.
This is especially important as we are going to introduce more changes
where the distinction between physical address and DMA address will be
key.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Some more U-Boot specific 64bit support changes, mostly changing u32
to unsigned long.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The mvpp2 is going to be extended to support the Marvell Armada 7K/8K
platform, which is ARM64. As a preparation to this work, this commit
enables building the mvpp2 driver on ARM64, by:
- Adjusting the Kconfig dependency
- Fixing the types used in the driver so that they are 32/64-bits
compliant. We use dma_addr_t for DMA addresses, and unsigned long
for virtual addresses.
It is worth mentioning that after this commit, the driver is for now
still only used on 32-bits platforms, and will only work on 32-bits
platforms.
Changed by Stefan for U-Boot:
Removed the Kconfig change as it does not apply to U-Boot this way.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Some of the MVPP2_PRS_RI_* definitions use the ~(value) syntax, which
doesn't compile nicely on 64-bit. Moreover, those definitions are in
fact unneeded, since they are always used in combination with a bit
mask that ensures only the appropriate bits are modified.
Therefore, such definitions should just be set to 0x0. In addition, as
suggested by Russell King, we change the _MASK definitions to also use
the BIT() macro so that it is clear they are related to the values
defined afterwards.
For example:
#define MVPP2_PRS_RI_L2_CAST_MASK 0x600
#define MVPP2_PRS_RI_L2_UCAST ~(BIT(9) | BIT(10))
#define MVPP2_PRS_RI_L2_MCAST BIT(9)
#define MVPP2_PRS_RI_L2_BCAST BIT(10)
becomes
#define MVPP2_PRS_RI_L2_CAST_MASK (BIT(9) | BIT(10))
#define MVPP2_PRS_RI_L2_UCAST 0x0
#define MVPP2_PRS_RI_L2_MCAST BIT(9)
#define MVPP2_PRS_RI_L2_BCAST BIT(10)
Because the values (MVPP2_PRS_RI_L2_UCAST, MVPP2_PRS_RI_L2_MCAST and
MVPP2_PRS_RI_L2_BCAST) are always applied with
MVPP2_PRS_RI_L2_CAST_MASK, and therefore there is no need for
MVPP2_PRS_RI_L2_UCAST to be defined as ~(BIT(9) | BIT(10)).
It fixes the following warnings when building the driver on a 64-bit
platform (which is not possible as of this commit, but will be enabled
in a follow-up commit):
drivers/net/ethernet/marvell/mvpp2.c: In function ‘mvpp2_prs_mac_promisc_set’:
drivers/net/ethernet/marvell/mvpp2.c:524:33: warning: large integer implicitly truncated to unsigned type [-Woverflow]
#define MVPP2_PRS_RI_L2_UCAST ~(BIT(9) | BIT(10))
^
drivers/net/ethernet/marvell/mvpp2.c:1459:33: note: in expansion of macro ‘MVPP2_PRS_RI_L2_UCAST’
mvpp2_prs_sram_ri_update(&pe, MVPP2_PRS_RI_L2_UCAST,
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The mvpp2_bm_bufs_add() currently creates a fake cookie by calling
mvpp2_bm_cookie_pool_set(), just to be able to call
mvpp2_pool_refill(). But all what mvpp2_pool_refill() does is extract
the pool ID from the cookie, and call mvpp2_bm_pool_put() with this ID.
Instead of doing this convoluted thing, just call mvpp2_bm_pool_put()
directly, since we have the BM pool ID.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
check_cache_range() warns that the top boundaries are not properly
aligned when flushing or invalidating the buffers and make these
operations fail.
This gets rid of the warnings:
CACHE: Misaligned operation at range ...
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add support for fixed link to NETA driver.
This feature requreed for proper support of SFP modules
and onboard connected devices like Ethernet switches
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Terry Zhou <bjzhou@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Add ability to use board-specific initialization flow
to NETA driver (for instance Ethernet switch bring-up)
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
MAC number used per QSGMII is not fixed. It may wary from SoC to SoC.
So move QSGMII wriop_init_dpmac() to SoC file.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch adds support for having a "fixed-link" to some other MAC
(like some embedded switch-device).
For this purpose we introduce a new phy-driver, called "Fixed PHY".
Fixed PHY works only with CONFIG_DM_ETH enabled, since the fixed-link is
described with a subnode below ethernet interface.
Most ethernet drivers (unfortunately not all are following same scheme
for searching/attaching phys) are calling "phy_connect(...)" for getting
a phy-device.
At this point we link in, we search here for a subnode called "fixed-
link", once found we start phy_device_create(...) with the special phy-
id PHY_FIXED_ID (0xa5a55a5a).
During init the "Fixed PHY" driver has registered with this id and now
gets probed, during probe we get all the details about fixed-link out of
dts, later on the phy reports this values.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Fixed cache misaligned issue in the net driver. The issue shows-up when
a call to flush_dcache_range is made with unaligned memory. The memory
must be aligned to ARCH_DMA_MINALIGN.
Signed-off-by: Suji Velupillai <suji.velupillai@broadcom.com>
Tested-by: Suji Velupillai <suji.velupillai@broadcom.com>
Reviewed-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Reviewed-by: JD Zheng <jiandong.zheng@broadcom.com>
Reviewed-by: Shamez Kurji <shamez.kurji@broadcom.com>
Signed-off-by: Steve Rae <steve.rae@raedomain.com>
Cover Letter:
This series resolves issues specific to the Broadcom SF2 driver:
- fix cache misaligned issue
- convert to Kconfig
END
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Currently the mac address is programmed directly in _sunxi_emac_eth_init
making it a one time inflexible operation. By moving it into a separate
function, we can now use this more flexibly.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add support for fixed link to NETA driver.
This feature requreed for proper support of SFP modules
and onboard connected devices like Ethernet switches
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Terry Zhou <bjzhou@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Add ability to use board-specific initialization flow
to NETA driver (for instance Ethernet switch bring-up)
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
- Move to DM clk driver
- Add clk support for zynq_sdhci
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAljKWVcACgkQykllyylKDCEsgACfey0mgRaGVMLSxMMCGgJQIK70
/oYAn3raqYrJ2e2fsjb1B5WodYcDe8L5
=JYC5
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2017.05' of git://www.denx.de/git/u-boot-microblaze
Xilinx changes for v2017.05
- Move to DM clk driver
- Add clk support for zynq_sdhci
Since the reserved RAM is tracked by gd->arch.resv_ram, calculation
of MC memory blocks can be simplified. The MC RAM is guaranteed to be
aligned by the reservation process.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Priyanka Jain <priyanka.jain@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
For ARMv8 Layerscape SoCs, secure memory and MC memorey are reserved
at the end of DDR. DDR is spit into two or three banks. This patch
reverts commit aabd7ddb and simplifies the calculation of reserved
memory, and moves the code into common SoC file. Secure memory is
carved out first. DDR bank size is reduced. Reserved memory is then
allocated on the top of available memory. U-Boot still has access
to reserved memory as data transferring is needed. Device tree is
fixed with reduced memory size to hide the reserved memory from OS.
The same region is reserved for efi_loader.
Signed-off-by: York Sun <york.sun@nxp.com>
When the zynq_gem driver initializes the phy it sets the supported
features that the phy can support and advertise. However instead of
masking the supported features such that it limits the available
features it sets the phy to have the exact supported features of the
zynq_gem. This is problematic as it will enable features that a phy does
not have or cannot advertise.
Specifically this appears as an issue when using a phy that is only
capable of 10/100, but the zynq_gem driver will override this and try to
enable and advertise 10/100/1000.
Reported-by: Arno Steffens <star@gmx.li>
Fixes: 80243528ef ("net: gem: Fix gem driver on 1Gbps LAN")
Signed-off-by: Nathan Rossi <nathan@nathanrossi.com>
Tested-by: Arno Steffens <star@gmx.li>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
For the boards such as smartweb on which the clock driver isn't
supported, the ethernet fail to be found when booting up with
the below log.
---8<---
Net: No ethernet found.
--->8---
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Move the zynq to clock framework and remove unused functions as well as
the CONFIG_ZYNQ_PS_CLK_FREQ configuration.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
If available use the clock framework to set the tx clock rate of the
zynq ethernet controller.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The gem[0-1]_rclk_ctrl registers control the source of the rx clock,
control and data signals and configure via ps7_init function. Don't
overwrite the register with the default value.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
cpsw driver tries to get macid for am43xx SoCs using the compatible
ti,am4372. But not all variants of am43x uses this complatible like
epos evm uses ti,am438x. So use a generic compatible ti,am43 to get
macid for all am43 based platforms.
Tested-by: Aparna Balasubramanian <aparnab@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
At present devices use a simple integer offset to record the device tree
node associated with the device. In preparation for supporting a live
device tree, which uses a node pointer instead, refactor existing code to
access this field through an inline function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Provide the necessary Kconfig symbols so that PHYLIB support may be
enabled in Kconfig, as opposed to needing to #define these symbols in
C source headers.
BITBANGMII and MV88E6352_SWITCH are left out of the PHYLIB submenu as
they don't seem to explicitly depend on it (i.e. they do not use the
phy_driver class).
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Modifying content of dev->name leads to the device tree corruption
because it points to the node name located there.
Signed-off-by: Daniel Strnad <strnadda@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
In Uboot for Meson GX the compatible string in meson-gxbb.dtsi so far is:
compatible = "amlogic,meson6-dwmac", "snps,dwmac";
On Linux in the same dt file it's
compatible = "amlogic,meson-gx-dwmac", "amlogic,meson-gxbb-dwmac", "snps,dwmac";
To avoid breaking ethernet with the next DT synch from Linux to U-Boot
(planned as prerequisite for adding Meson GX MMC driver to U-Boot) add
"amlogic,meson-gx-dwmac" to the compatibility list in the designware
driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add support for programmable MAC impedance configuration and
fix typo in DT impedance parameters names.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Commit 79e86ccb37 "vitesse: remove duplicated
argument to ||" correctly removed a redundant check.
However, I believe that the original code was simply wrong, and should have
been checking against RGMII_ID.
To fix this and avoid similar problems in the future, use the
phy_interface_is_rgmii helper function.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This device also works with the 88E1518 code, so we just adjust
the UID mask accordingly.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The mask for the 88E1510 meant that the 88E1518 code would never be
used.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
There is code that is specifically for RGMII_TXID interface, but this
will never get used because the code checks that the RGMII interface
is RGMII_ID to RGMII_RXID; RGMII_TXID is after this.
To fix this and avoid similar problems in the future, use the
phy_interface_is_rgmii helper function.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Remove the redundant #ifdef CONFIG_DM_ETH/#endif.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Due to introducing the at91 clock driver, add the clock support.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add support for Marvell 88E1680 Integrated Octal
10/100/1000 Mbps Energy Efficient Ethernet Transceiver.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Fixup port_mac_address property in MC DPC with values from the u-boot
environment. Since u-boot already reads the environment MAC addresses
when probing the PHYs, use these values.
The u-boot environment MAC addresses take precedence over any eventual
ones defined in the DPC, except for the case where they are randomly
assigned (no u-boot env value declared for port).
The patch assumes the "/board_info/ports/" node is present in the DPC.
Signed-off-by: Bogdan Purcareata <bogdan.purcareata@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
[York S: Fix several indentations]
Reviewed-by: York Sun <york.sun@nxp.com>
This patch adds support for SMSC LAN8742 in phylib
Signed-off-by: Michael Kurz <michi.kurz@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch adds glue code required for enabling the designware
mac on stm32f7 devices.
Signed-off-by: Michael Kurz <michi.kurz@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add a new driver for the GMAC ethernet interface present in Rockchip
RK3288 SOCs. This driver subclasses the generic design-ware driver to
add the glue needed specifically for Rockchip.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Export all functions so that drivers can use them, or not, as the need
arises.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
With rockchip we need to make adjustments after the link speed is set but
before enabling received/transmit. In preparation for this, split these
two pieces into separate functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This function can fail, so return the error if there is one.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
To allow other DM drivers to subclass the designware driver various
functions and structures need to be exported. Export these.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch fixes incorrect pointer on offset device in device tree blob.
When using with the component "Ethernet 1G/2.5G BASE-X PCS/PMA or SGMII"
it does not understand what type is XAE_PHY_TYPE_1000BASE_X and trying
to change frequency.
Signed-off-by: Kamensky Ivan <kamensky.ivan@mail.ru>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Enable and use the clock driver routine
defined in clock driver toset required
clock appropriately.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
I am not longer using my old email address
"ajay.bhargav@einfochips.com". For U-Boot development email address is
now updated to contact@8051projects.net
Signed-off-by: Ajay Bhargav <contact@8051projects.net>
axi_emac, emaclite and gem have the same issue with registering
multiple instances with mdio busses. mdio bus name has to be uniq but
drivers are setting up only one name for all.
Use mdio_register_seq() and pass dev->seq number to allow multiple
mdio instances registration.
Reported-by: Phani Kiran Kara <phanikiran.kara@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
- Remove exctra space
- Add space
- Add tab space
- Fix single line comments quotes
- Fix 'CHECK: Avoid CamelCase'
- Fix 'CHECK: Alignment should match open parenthesis'
- Fix 'WARNING: line over 80 characters'
- Re-arrage header include files
Cc: Simon Glass <sjg@chromium.org>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
This patch add driver model support for fec_mxc driver.
Cc: Simon Glass <sjg@chromium.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
fec_get_hwaddr never used eth_device argument, hence removed.
Cc: Simon Glass <sjg@chromium.org>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add CX9020 board based on mx53loco.
Add simplified imx53 base device tree from kernel v4.8-rc8, to reuse
serial_mxc with DTE and prepare for device tree migration of other
functions and imx53 devices.
The CX9020 differs from i.MX53 Quick Start Board by:
- use uart2 instead of uart1
- DVI-D connector instead of VGA
- no audio
- CCAT FPGA connected to emi
- enable rtc
Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
LS2080A SoC family has QBMAN ver 4.0 whereas newer
SoCs like LS2088A, LS1088A has QBMAN ver 4.1
QBMAN ver 4.0 and ver 4.1 supports dqrr size as 4 and 8 respectively.
Add support of
to check QBMAN version based on SoC SVR
update dqrr_size accordingly
update code to support larger dqrr_size
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The VSC8601 config tried to add an RGMII skew based on #defines that
no config defines. That's quite an ugly way to do it. Since the skew
is only needed on RGMII interfaces, check the interface mode at
runtime, and apply the settings accordingly.
Tested on custom board with AM3352 SOC and VSC801 PHY.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The settings for 2.5G SGMII are wrong, which the 2.5G case is missed in
set_if_mode(), and the serdes PCS configuration are wrong, this patch uses
the correct settings took from Linux.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Commit 525d187af ("net: phy: Optionally force master mode for RTL PHY")
added the define to force the PHY into master mode. Unfortunatly this is
an all or nothing switch. So it applies to either all PHY's or no PHY's.
The bug that define tried to solve was a buggy PLL in the RTL8211C only.
The Olimex OLinuXino Lime2 has gotten an upgrade where the PHY was
replaced with an RTL8211E. With this define however, both lime2 boards
are either forced to master mode or not. We could of course have a
binary for each board, but the following patch fixes this by adding a
'quirk' to the flags to the rtl8211b and rtl8211c only. It is now
possible to force master mode, but only have it apply to the rtl8211b
and rtl8211c.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
All internal defines in the realtek phy are with a small X,
except MIIM_RTL8211X_CTRL1000T_MASTER. Make this more consistent
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The BIT macro is the preferred method to set bits.
This patch adds the bit macro and converts bit invocations.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Fix the following error, the $ret variable handling must
be part of the loop, while due to the missing parenthesis
it was not.
drivers/net/phy/micrel.c: In function ‘ksz9021_of_config’:
drivers/net/phy/micrel.c:303:2: warning: this ‘for’ clause does not guard... [-Wmisleading-indentation]
for (i = 0; i < ARRAY_SIZE(ofcfg); i++)
^~~
drivers/net/phy/micrel.c:305:3: note: ...this statement, but the latter is misleadingly indented as if it is guarded by the ‘for’
if (ret)
^~
drivers/net/phy/micrel.c: In function ‘ksz9031_of_config’:
drivers/net/phy/micrel.c:411:2: warning: this ‘for’ clause does not guard... [-Wmisleading-indentation]
for (i = 0; i < ARRAY_SIZE(ofcfg); i++)
^~~
drivers/net/phy/micrel.c:413:3: note: ...this statement, but the latter is misleadingly indented as if it is guarded by the ‘for’
if (ret)
^~
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
axi_emac, emaclite and gem have the same issue with registering
multiple instances with mdio busses. mdio bus name has to be uniq but
drivers are setting up only one name for all.
Use mdio_register_seq() and pass dev->seq number to allow multiple
mdio instances registration.
Reported-by: Phani Kiran Kara <phanikiran.kara@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Series-to: u-boot
Series-cc: Phani Kiran Kara <phanikiran.kara@gmail.com>
The rtl8169_intr_mask variable isn't used anywhere in the code, so
just remove it to avoid a GCC 6.2 compiler warning.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Apparently the indentation is off here, for the IGB model just want to
bail out early.
Fix this to avoid both compiler warnings and puzzled readers.
Pointed out by GCC 6.2's -Wmisleading-indentation warning.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
It is confusing that mdio commands work and report phy id as
decimal value when mii is working with hex values.
For example:
ZynqMP> mdio list
gem:
21 - TI DP83867 <--> ethernet@ff0e0000
ZynqMP> mdio read ethernet@ff0e0000 0
Reading from bus gem
PHY at address 21:
0 - 0x1140
ZynqMP> mii dump 21 0
Incorrect PHY address. Range should be 0-31
...
ZynqMP> mii dump 15
0. (1140) -- PHY control register --
(8000:0000) 0.15 = 0 reset
U-Boot normally takes hex values that's why this patch is changing mdio
command to handle hex instead of changing mii command to handle decimal
values.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add support to detect RGMII link interface from link-interface
device tree entry. Also rename the existing link type enums so
that it provides meaningful interface like SGMII.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reported-by: Sekhar Nori <nsekhar@ti.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
To send a parametrized command to the PHY over MDIO, we should write
the data first, the trigger the execution by the command register
write. Fix the access pattern in our MDIO write routine.
Apparently this doesn't really matter with the Realtek PHY on the
Pine64, but other PHYs (which require more setup) will choke on
the wrong order.
[Andre: add commit message]
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Jagan Teki <jagan@openedev.com>
P1017 is a single-core version of P1023. There is no P1017 target
configured. Drop related macros. P1017 SoC is still supported.
Signed-off-by: York Sun <york.sun@nxp.com>
Highlights this time around:
- x86 efi_loader support
- hello world efi test case
- network device name is now representative
- terminal output reports modes correctly
- fix psci reset for ls1043/ls1046
- fix efi_add_runtime_mmio definition for x86
- efi_loader support for ls2080
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=xmR3
-----END PGP SIGNATURE-----
Merge tag 'signed-efi-next' of git://github.com/agraf/u-boot
Patch queue for efi - 2016-11-17
Highlights this time around:
- x86 efi_loader support
- hello world efi test case
- network device name is now representative
- terminal output reports modes correctly
- fix psci reset for ls1043/ls1046
- fix efi_add_runtime_mmio definition for x86
- efi_loader support for ls2080
On ls2080 we have a separate network fabric component which we need to
shut down before we enter Linux (or any other OS). Along with that also
comes configuration of the fabric using a description file.
Today we always stop and configure the fabric in the boot script and
(again) exit it on device tree generation. This works ok for the normal
booti case, but with bootefi the payload we're running may still want to
access the network.
So let's add a new fsl_mc command that defers configuration and stopping
the hardware to when we actually exit U-Boot, so that we can still use
the fabric from an EFI payload.
For existing boot scripts, nothing should change with this patch.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: York Sun <york.sun@nxp.com>
[agraf: Fix x86 build]
Correct the SGMII enable bit position to 27 instead
of 31.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Modify the nwcfg bit definitions to have 32-bit
by removing the extra nibble.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Commit 5a49f17481 ("net: mii: Use spatch to update miiphy_register")
updated the mvgbe implementation of smi_reg_read/smi_reg_write. Prior to
that change mvgbe_phy_read and mvgbe_phy_write where used as wrappers to
satisfy the phylib APIs. Because these functions weren't updated in that
commit build errors where triggered when CONFIG_PHYLIB was enabled.
Fix these build errors by removing mvgbe_phy_read and mvgbe_phy_write
and using smi_reg_read/smi_reg_write directly.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Like [1], reset the FLP burst timing for the KSZ9031 to the 16ms
specified by the IEEE802.3 standard from the chip's default of 8ms.
For more details, see the "Auto-Negotiation Timing" section of the
KSZ9031RNX datasheet.
[1] https://patchwork.kernel.org/patch/6558371/
Signed-off-by: Ash Charles <ash.charles@savoirfairelinux.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This driver supports the Synopsys Designware Ethernet QoS (Quality of
Service) a/k/a eqos IP block, which is a different design than the HW
supported by the existing designware.c driver. The IP supports many
options for bus type, clocking/reset structure, and feature list. This
driver currently supports the specific configuration used in NVIDIA's
Tegra186 chip, but should be extensible to other combinations quite
easily, as explained in the source.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org> # V1
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Cover-Letter: Fixes several spelling errors for the words "resetting",
"extended", "occur", and "multiple".
Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Commit b02e4044ff ("libfdt: Bring in upstream stringlist
functions") broke codying style in some places especially
by inserting an extra whitespace before fdt_stringlist_count().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
These two files have patch merge markers in them, within comments or
strings. Remove then, so that a search for merge markers does not show up
matches in these files.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
The signature for this macro has changed. Bring in the upstream version and
adjust U-Boot's usages to suit.
Signed-off-by: Simon Glass <sjg@chromium.org>
Update to drivers/power/pmic/palmas.c:
Signed-off-by: Keerthy <j-keerthy@ti.com>
Change-Id: I6cc9021339bfe686f9df21d61a1095ca2b3776e8
These have now landed upstream. The naming is different and in one case the
function signature has changed. Update the code to match.
This applies the following upstream commits by
Thierry Reding <treding@nvidia.com> :
604e61e fdt: Add functions to retrieve strings
8702bd1 fdt: Add a function to get the index of a string
2218387 fdt: Add a function to count strings
Signed-off-by: Simon Glass <sjg@chromium.org>
The call to flush cache on the transmit buffer was misplaced (for very
short packets) and asked to flush less than a cacheline.
Move the flush cache call to after a short packet has been padded
to minimum length (so the padding is flushed too), and round the size
up to a cacheline.
Signed-off-by: Peter Chubb <peter.chubb@data61.csiro.au>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
On some boards these switches are wired directly into a SERDES
interface on another Ethernet MAC. Add the ability to specify
these kinds of boards using CONFIG_MV88E61XX_FIXED_PORTS which defines
a bit mask of these fixed ports.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The Marvell Link Street mv88e60xx is a series of FastEthernet switch
chips, some of which also support Gigabit ports. It is similar to the
mv88e61xx series which support Gigabit on all ports.
The main difference is the number of ports. Which affects the
PORT_COUNT define and the size of the mask passed to
mv88e61xx_port_set_vlan().
Other than that it's just a matter of adding the appropriate chip
IDs.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Cc: Joshua Scott <joshua.scott@alliedtelesis.co.nz>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
cpsw driver supports only selection of phy mode in control module
but control module has more setting like RGMII ID mode selection,
RMII clock source selection. So ported to cpsw-phy-sel driver
from kernel to u-boot.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
In the current driver implementation, config() callback is common
for AR8035 and AR8031 phy. In config() callback, driver tries to
configure MMD Access Control Register and MMD Access Address Data
Register unconditionally for both phy versions which leads to
auto negotiation failure in AM335x EVMsk second port which uses
AR8031 Giga bit RGMII phy. Fixing this by adding separate config
for AR8031 phy.
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This adds support for internal delay on RX and TX on RGMII interface for the
AR8035 phy.
This is basically the same Linux driver do. Tested on a Zynq Zturn board (for
which u-boot support in is my tree; first patch waiting ML approval)
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Fix various misspellings of:
* deprecated
* partition
* preceding,preceded
* preparation
* its versus it's
* export
* existing
* scenario
* redundant
* remaining
* value
* architecture
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Stefan Roese <sr@denx.de>
when using tftp on the smartweb board, it prints a lot of
CACHE: Misaligned operation at range [23b2e000, 23b2e100]
warnings ... fixed them.
Signed-off-by: Heiko Schocher <hs@denx.de>
This patch adds support for the Armada 3700 SoC to the Marvell mvneta
network driver.
Not like A380, in Armada3700, there are two layers of decode windows for GBE:
First layer is: GbE Address window that resides inside the GBE unit,
Second layer is: Fabric address window which is located in the NIC400
(South Fabric).
To simplify the address decode configuration for Armada3700, we bypass the
first layer of GBE decode window by setting the first window to 4GB.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The mvneta driver is also used on the ARMv8 64bit Armada 3700 SoC. This
patch fixes the compilation warnings seen on this 64bit platform.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
check_cache_range() warns that the top boundaries are not properly
aligned when flushing or invalidating the buffers and make these
operations fail.
This gets rid of the warnings:
CACHE: Misaligned operation at range ...
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Move this option to Kconfig and clean up existing uses.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Mingkai Hu <mingkai.hu@nxp.com>
CC: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Now, include/linux/errno.h is a wrapper of <asm-generic/errno.h>.
Replace all include directives for <asm-generic/errno.h> with
<linux/errno.h>.
<asm-generic/...> is supposed to be included from <asm/...> when
arch-headers fall back into generic implementation. Generally, they
should not be directly included from .c files.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Add drivers/usb/host/xhci-rockchip.c]
Signed-off-by: Tom Rini <trini@konsulko.com>
Now, arch/${ARCH}/include/asm/errno.h and include/linux/errno.h have
the same content. (both just wrap <asm-generic/errno.h>)
Replace all include directives for <asm/errno.h> with <linux/errno.h>.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Fixup include/clk.]
Signed-off-by: Tom Rini <trini@konsulko.com>
The pch_gbe driver previously casted pointers to & from unsigned 32 bit
integers in many locations. This breaks the driver on 64 bit systems,
producing streams of compiler warnings about mismatched pointer &
integer sizes and then failing to keep track of addresses correctly at
runtime.
Fix the driver for 64 bit systems by using unsigned longs in place of
the previously used 32 bit integers.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reading the PCI BAR & converting the result to a physical address is not
safe across all architectures. For example on MIPS the virtual:physical
mapping is not 1:1, so we cannot directly make use of the physical
address.
Use the more generic BAR-mapping function dm_pci_map_bar to discover the
MMIO base address, which should work across architectures.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
out_be32 and in_be32 are actually #defined to little endian
writel/readl in arch/microblaze.
Just use __raw_writel/readl instead. That is also what is used
in the Linux kernel driver for this IP block
Tested on MIPSfpga. Can tftp a kernel.
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Virtual to physical mapping isn't necessarily 1:1 for all architectures
Using ioremap_nocache allows for the arch code to translate the
physical address to a virtual address.
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The current code would always use the speed and mode set by
CONFIG_ENV_SPI_MAX_HZ and CONFIG_ENV_SPI_MODE. But if using
SPI driver model it should get the values from DT.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Remove the device definition from board file, update the driver with
the new compatible property and update config with necessary options.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The spatch series converting legacy drivers from miiphy_register to
mdio_register changed the return convention of the davinci_emac internal
MDIO accessors, making the internal code relying on it misbehaving:
no mdiodev get registered and U-Boot crashes when using net cmds in the
context of the old legacy net API.
ATM davinci_emac_initialize and cpu_eth_init don't return a proper value
in that case but fixing them would not avoid the crash.
This change is just a follow-up to the spatch pass, the MDIO accessors
of the mdiodev introduced by the spatch pass retain their proper values.
Signed-off-by: Karl Beldan <karl.beldan+oss@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
