Commit graph

7884 commits

Author SHA1 Message Date
Simon Glass
5a8ba315f1 samsung: Drop more references fo s3c24x0
This is dead code now. Drop it.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-06-05 11:02:31 -04:00
Simon Glass
0d8c939414 samsung: Drop s3c24x0 arch-specific code
This is not used anymore. Drop it.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-06-05 11:02:29 -04:00
Tom Rini
8bb687fdc1 t81xx: Migrate TI81XX/TI816X/TI814X symbols to Kconfig
The symbol CONFIG_TI81XX is used for the parts that are common to the
TI816x and TI814x SoCs and are not part of CONFIG_ARCH_OMAP2PLUS nor
CONFIG_AM33XX.  It however has so few uses that we can just modify the
code to check for both and drop the symbol. The symbols CONFIG_TI816X
and CONFIG_TI814X are for the repective SoCs.

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-06-05 11:02:25 -04:00
Tom Rini
708ca4daf9 ti816x: Import dts files from Linux Kernel v4.11
This brings in the required dts/dtsi files for the TI8168-EVM from the
Linux Kernel v4.11 release.

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-06-05 11:02:25 -04:00
Tom Rini
8627733941 ti816x: Rework DDR initialization sequence
The ti816x/am389x SoC is the first generation in what U-Boot calls the
"am33xx" family.  In the first generation of this family the DDR
initialization sequence is quite different from all of the subsequent
generations.  Whereas with ti814x (second generation) we can easily work
the minor differenced between that and am33xx (third generation), our
attempts to do this for ti816x weren't sufficient.  Rather than add a
large amount of #ifdef logic to make this different sequence work we add
a new file, ti816x_emif4.c to handle the various required undocumented
register writes and sequence and leverage what we can from
arch/arm/mach-omap2/am33xx/ddr.c still.  As DDR2 has similar problems
today but I am unable to test it, we drop the DDR2 defines from the code
rather than imply that it works by leaving it.  We also remove a bunch
of other untested code about changing the speed the DDR runs at.

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-06-05 11:02:23 -04:00
Tom Rini
ffb5656862 armv7: Mark the default lowlevel_init function as weak
Rather than have a long and if check in the Makefile, mark the default
lowlevel_init function as weak (as we do on armv8) so that SoCs can
override it if needed, and it will still be discarded if unused.
Provide a weak s_init as well to allow for this to link and be
discarded.

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-06-05 11:02:23 -04:00
Jaehoon Chung
c9972a8652 ARM: dts: exynos5422-odroidxu3: add the LDO's nodes
Add the LDO's nodes that taken from Linux Kernel.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2017-06-05 11:06:52 +09:00
Jaehoon Chung
9c2e2cab9a ARM: dts: exynos4: change the nodes relevant to mmc/sd
Change the nodes relevant to mmc/sd for using DM.
compatible are also changed to each SoCs.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2017-06-05 11:06:42 +09:00
Tom Rini
541f538f4c Merge git://git.denx.de/u-boot-fsl-qoriq 2017-06-03 18:05:04 -04:00
Tom Rini
b07d044d5b Merge git://git.denx.de/u-boot-sunxi 2017-06-03 18:04:54 -04:00
Tom Rini
91d27a17c6 Kconfig: Migrate FS_FAT / FAT_WRITE
Now that these symbols are in Kconfig, migrate all users.  Use imply on
a number of platforms that default to having this enabled.  As part of
this we must migrate some straglers for CMD_FAT and DOS_PARTITION.

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-06-03 17:55:34 -04:00
Jagan Teki
868e37159e sun50i: h5: Add initial Orangepi Prime support
Orangepi Prime is an open-source single-board computer
using the Allwinner h5 SOC.

H5 Orangepi Prime has
- Quad-core Cortex-A53
- 2GB DDR3
- Debug TTL UART
- 1000M/100M Ethernet RJ45
- Three USB 2.0
- HDMI
- Audio and MIC
- Wifi + BT
- IR receiver
- HDMI
- Wifi + BT

Boot from MMC:
-------------
U-Boot SPL 2017.05-00662-ga3f4c05-dirty (May 25 2017 - 13:30:14)
DRAM: 2048 MiB
Trying to boot from MMC1
NOTICE:  BL3-1: Running on H5 (1718) in SRAM A2 (@0x44000)
NOTICE:  Configuring SPC Controller
NOTICE:  BL3-1: v1.0(debug):aa75c8d
NOTICE:  BL3-1: Built : 18:28:27, May 24 2017
INFO:    BL3-1: Initializing runtime services
INFO:    BL3-1: Preparing for EL3 exit to normal world
INFO:    BL3-1: Next image address: 0x4a000000, SPSR: 0x3c9

U-Boot 2017.05-00662-ga3f4c05-dirty (May 25 2017 - 13:30:14 +0000) Allwinner Technology

CPU:   Allwinner H5 (SUN50I)
Model: OrangePi Prime
DRAM:  2 GiB
MMC:   SUNXI SD/MMC: 0
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   phy interface7
eth0: ethernet@1c30000
starting USB...
USB0:   USB EHCI 1.00
USB1:   USB OHCI 1.0
scanning bus 0 for devices... 1 USB Device(s) found
       scanning usb for storage devices... 0 Storage Device(s) found
Hit any key to stop autoboot:  0

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-06-02 13:28:07 +00:00
York Sun
8e59778bec armv8: layerscape: Enabling loading PPA during SPL stage
Loading PPA in SPL puts the rest of U-Boot (including RAM version
loaded later) in EL2 with MMU and cache enabled. Once PPA is loaded,
PSCI is available.

Signed-off-by: York Sun <york.sun@nxp.com>
2017-06-01 19:57:24 -07:00
York Sun
399e2bb60c armv8: layerscape: Make U-Boot EL2 safe
When U-Boot boots from EL2, skip some lowlevel init code requiring
EL3, including CCI-400/CCN-504, trust zone, GIC, etc. These
initialization tasks are carried out before U-Boot runs. This applies
to the RAM version image used for SPL boot if PPA is loaded first.

Signed-off-by: York Sun <york.sun@nxp.com>
2017-06-01 19:57:24 -07:00
Santan Kumar
1f55a93802 armv8: ls2080aqds: Add support for SD boot
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Abhimanyu Saini <abhimanyu.saini@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-06-01 19:57:17 -07:00
Santan Kumar
faed6bde11 armv8: ls2080a: Reorganise NAND_BOOT code in config flag
Add CONFIG_NAND_BOOT config flag to organise
NAND_BOOT specific code in config flag like
-nand-boot specfic errata errata_rcw_src()
-CONFIG_SYS_NAND_U_BOOT_DST,etc

Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Abhimanyu Saini <abhimanyu.saini@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-06-01 19:57:07 -07:00
Jagan Teki
f333973340 arm64: dts: sun50i: h5: orangepi-pc2: Use GPIO flag binding macro
Instead of defining numerical value on GPIO flag
better to use existing binding macro.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-06-01 14:42:08 +00:00
Jagan Teki
702a3e579b arm64: dts: sun50i: Add sun50i-h5.dtsi
The Allwinner H5 SoC is pin-compatible to the H3 SoC,
but uses Cortex-A53 cores instead.

So move the shared cpu based and peripherals nodes into
sun50i-h5.dtsi so, that it can shared among the sun50i-h5
board dts files.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-06-01 14:35:23 +00:00
Simon Glass
eed36609b5 fdt: Rename a few functions in fdt_support
These two functions have an of_ prefix which conflicts with naming used
in of_addr. Rename them:

   fdt_read_number
   fdt_support_bus_default_count_cells

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-06-01 07:03:11 -06:00
Simon Glass
da409ccc4a dm: core: Replace of_offset with accessor (part 2)
At present devices use a simple integer offset to record the device tree
node associated with the device. In preparation for supporting a live
device tree, which uses a node pointer instead, refactor existing code to
access this field through an inline function.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-06-01 07:03:04 -06:00
Simon Glass
4af0d7e870 dm: Fix up inclusion of common.h
It is good practice to include common.h as the first header. This ensures
that required features like the DECLARE_GLOBAL_DATA_PTR macro,
configuration options and common types are available.

Fix up some files which currently don't do this. This is necessary because
driver model will soon start using global data and configuration in the
dm/read.h header file, included via dm.h. The gd->fdt_blob value will be
used to access the device tree and CONFIG options will be used to
determine whether to support inline functions in the header file.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-06-01 07:03:03 -06:00
Simon Glass
a821c4af79 dm: Rename dev_addr..() functions
These support the flat device tree. We want to use the dev_read_..()
prefix for functions that support both flat tree and live tree. So rename
the existing functions to avoid confusion.

In the end we will have:

   1. dev_read_addr...()    - works on devices, supports flat/live tree
   2. devfdt_get_addr...()  - current functions, flat tree only
   3. of_get_address() etc. - new functions, live tree only

All drivers will be written to use 1. That function will in turn call
either 2 or 3 depending on whether the flat or live tree is in use.

Note this involves changing some dead code - the imx_lpi2c.c file.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-06-01 07:03:01 -06:00
Simon Glass
9d922450aa dm: Use dm.h header when driver mode is used
This header includes things that are needed to make driver build. Adjust
existing users to include that always, even if other dm/ includes are
present

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-06-01 06:57:52 -06:00
Jagan Teki
2dbe9c1362 sun50i: a64: Add initial Banana Pi M64 support
BPI-M64 is a 64-bit quad-core mini single board computer
using the Allwinner A64 SOC.

BPI-M64 features
- 1.2 Ghz Quad-Core ARM Cortex A53
- 2GB DDR3 SDRAM with 733MHz
- MicroSD/eMMC(8GB)
- 10/100/1000Mbps ethernet (Realtek RTL8211E/D)
- Wifi + BT
- IR receiver
- Audio In/Out
- Video In/Out
- 5V 2A DC power-supply

For dts file,
Sync with Linux commit 4879b7ae("Merge tag 'dmaengine-4.12-rc1'").

Boot from MMC:
-------------
U-Boot SPL 2017.05-00667-g85dd258-dirty (May 29 2017 - 13:07:31)
DRAM: 2048 MiB
Trying to boot from MMC1
NOTICE:  BL3-1: Running on A64/H64 (1689) in SRAM A2 (@0x44000)
NOTICE:  Configuring SPC Controller
NOTICE:  BL3-1: v1.0(debug):aa75c8d
NOTICE:  BL3-1: Built : 18:28:27, May 24 2017
NOTICE:  Configuring AXP PMIC
NOTICE:  PMIC: setup successful
INFO:    BL3-1: Initializing runtime services
INFO:    BL3-1: Preparing for EL3 exit to normal world
INFO:    BL3-1: Next image address: 0x4a000000, SPSR: 0x3c9

U-Boot 2017.05-00667-g85dd258-dirty (May 29 2017 - 13:07:31 +0000) Allwinner Technology

CPU:   Allwinner A64 (SUN50I)
Model: BananaPi-M64
DRAM:  2 GiB
MMC:   SUNXI SD/MMC: 0, SUNXI SD/MMC: 1
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   No ethernet found.
starting USB...
No controllers found
Hit any key to stop autoboot:  0

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-06-01 09:26:05 +00:00
Andre Przywara
f98852bfa9 sunxi: A64/Pine64: update device tree from Linux
The Linux device tree for the Allwinner A64 SoC has changed a lot since
the U-Boot version was merged.
Let's replace the current DT with a exact copy of the Linux one as of:
commit c6778ff813d2ca3e3c8733c87dc8b6831a64578b
Merge: 0ff4c01 3c0e3abd
Author: Linus Torvalds <torvalds@linux-foundation.org>
Date:   Tue May 9 10:07:33 2017 -0700

This is the DT used in Linux 4.12-rc1.

Since U-Boot has an Ethernet driver (while Linux does not yet), we
provide the required DT nodes for it in an ...-u-boot.dtsi file, to both
mark them as U-Boot specific and to allow easier upgrading once Linux gets
the driver and its own binding later.
Compared to the existing Ethernet DT nodes we just slightly tweak the clock
and reset nodes in there to match the new bindings used by Linux for those.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
2017-06-01 09:25:30 +00:00
Tom Rini
1b87f9538f Merge git://www.denx.de/git/u-boot-marvell
Mostly including the Armada 37xx pinctrl / gpio driver.
2017-05-31 22:27:54 -04:00
Daniel Thompson
221a949eb6 Kconfig: Finish migration of hashing commands
Currently these (board agnostic) commands cannot be selected using
menuconfig and friends. Fix this the obvious way.  As part of this,
don't muddle the meaning of CONFIG_HASH_VERIFY to mean both 'hash -v'
and "we have a hashing command" as this makes the Kconfig logic odd.

Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
[trini: Re-apply, add imply for a few cases, run moveconfig.py, also
        migrate CRC32_VERIFY]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-05-31 19:38:14 -04:00
Benoît Thébaudeau
3e3aab3379 mx25: Add function to set PER clocks
Introduce the imx_set_perclk() function to make it possible to set the
PER clocks.

Signed-off-by: Benoît Thébaudeau <benoit@wsystem.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-05-31 10:14:30 +02:00
Benoît Thébaudeau
f7c13e6a79 mx25: Fix imx_get_perclk()
imx_get_perclk() used the AHB clock as the clock source for all PER
clocks, but the USB PLL output can also be a PER clock source if the
corresponding PER CLK MUX bit is set in CCM.MCR.

Signed-off-by: Benoît Thébaudeau <benoit@wsystem.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-05-31 10:14:17 +02:00
Tim Harvey
6ecbe13756 drivers: pci: imx: add imx_pcie_remove function
There is no dedicated reset signal wired up for the MX6QDL thus if the
bootloader enables the link we need some special handling to get the core
back into a state where it is safe to touch it for configuration.

While there has been some special handling in the Linux kernel to do this,
it was removed in 4.11 thus we need to do it properly in the bootloader
and therefore without this if you enable PCI in the bootloader you will hang
while booting the 4.11 kernel.

This puts the PCIe controller back into a safe state for the kernel driver
before launching the kernel.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Peter Senna Tschudin <peter.senna@collabora.com>
2017-05-31 10:09:03 +02:00
Vanessa Maegima
1541d7a63d pico-imx7d: Add initial support
Add the initial support for pico-imx7d board based on Wig Cheng's
source code.

Add support for eMMC, USB gadget, I2C, PMIC and Ethernet.

For more information about this board, please visit:
http://www.technexion.org/products/pico/pico-som/pico-imx7-emmc

Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-05-31 09:58:40 +02:00
Stefan Roese
780f80cd0f arm64: mvebu: Replace board specific with generic memory bank decoding
The dram_init and dram_init_banksize functions were using a board
specific implementation for decoding the memory banks from the fdt.
This change makes the dram_init* functions use a generic implementation
of decoding and populating memory bank and size data.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nathan Rossi <nathan@nathanrossi.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2017-05-31 07:42:17 +02:00
Stefan Roese
0cc209124f arm64: mvebu: armada-7040-db: Enable 10GB port 0 / SFI (KR)
This patch enables the mvpp2 port 0 usage on the Armada 7k DB by setting
the correct PHY type (KR / SFI) for the COMPHY driver and enabling the
ethernet0 device node in the dts.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefan Chulski <stefanc@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
2017-05-31 07:39:06 +02:00
Gregory CLEMENT
045504bbb8 arm64: mvebu: armada37xx: add pinctrl definition
Start to populate the device tree of the Armada 37xx with the pincontrol
configuration used on the board providing a dts.

Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Konstantin Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
2017-05-31 07:33:49 +02:00
Gregory CLEMENT
5cb7b79558 arm64: mvebu: Add pinctrl nodes for Armada 3700
Add the nodes for the two pin controller present in the Armada 37xx SoCs.

Initially the node was named gpio1 using the same name that for the
register range in the datasheet. However renaming it pinctr_nb (nb for
North Bridge) makes more sens.

Minor changes for U-Boot because of the slightly different dts version
done by Stefan Roese.

Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Konstantin Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
2017-05-31 07:33:49 +02:00
Mylene JOSSERAND
6ff02fba04 sunxi: Update NanoPi Neo to use dtsi
Update the NanoPi Neo device tree file to use the NanoPi dtsi.

Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2017-05-30 11:05:24 +05:30
Mylene JOSSERAND
a647ea172a sunxi: Add support for NanoPi M1
NanoPi M1 is a board based on Allwinner H3 CPU.

This commit adds the support for this platform with:
   - an include device tree which enables UART, LEDs, GPIO key switch,
   1 USB host ports and the SD-card as a dtsi file.
   - a device tree specific to this board that enables the
   2 additional USB ports
   - a defconfig file for minimal support
   - a section in MAINTAINERS (add myself)

Synchronized with the kernel device tree, from commits:
sun8i-nanopi.dtsi: 85d2913614d9ab899d23b7ab7d22d23cf45bd1de
sun8i-h3-nanopi-m1.dts: 10efbf5f16336b7540ad6a16aa1cb0b26bab033b

Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2017-05-30 11:05:09 +05:30
Tom Rini
380e86f361 Merge git://git.denx.de/u-boot-fsl-qoriq 2017-05-26 11:19:27 -04:00
Tom Rini
be62fbf376 Merge branch 'rmobile' of git://git.denx.de/u-boot-sh 2017-05-23 16:22:03 -04:00
Santan Kumar
f5bf23d827 armv8: ls2080ardb, ls2080aqds: Adjust memory map for NOR-boot
This patch adjusts memory map for images on LS2080ARDB and
LS2080AQDS NOR flash as below

Image				Flash Offset
RCW+PBI				0x00000000
Boot firmware (U-Boot)		0x00100000
Boot firmware Environment	0x00300000
PPA firmware			0x00400000
PHY firmware			0x00980000
DPAA2 MC			0x00A00000
DPAA2 DPL			0x00D00000
DPAA2 DPC			0x00E00000
Kernel.itb			0x01000000

Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-05-23 09:52:29 -07:00
Alison Wang
a9a5cef391 armv8: layerscape: Adjust memory mapping for Flash/SD card on LS1043A
This patch is to adjust the memory mapping for FLash/SD card on
LS1043AQDS and LS1043ARDB, such as PPA firmware load address, FMAN
firmware load address, QE firmware load address, U-Boot start address
on serial flash and environment address.

Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-05-23 09:50:25 -07:00
Priyanka Jain
3049a583f3 armv8: ls2080ardb: Add LS2081ARDB board support
LS2081ARDB board is similar to LS2080ARDB board with few differences
 It hosts LS2081A SoC
 Default boot source is QSPI-boot
 It does not have IFC interface
 RTC and QSPI flash device are different
 It provides QIXIS access via I2C

Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-05-23 09:47:08 -07:00
Priyanka Jain
e809e74799 armv8: fsl-layerscape: Add NXP LS2081A, LS2041A SoC support
The QorIQ LS2081A SoC has eight 64-bit ARM v8 Cortex A72 cores and
is built on layerscape architecture. It is 40-pin derivative of
LS2084A (non-AIOP personality of LS2088A). So feature-wise it is
same as LS2084A. LS2041A is a 4-core personality of LS2081A.

Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-05-23 09:40:23 -07:00
Priyanka Jain
89a168f776 armv8: ls2080ardb: Add QSPI-boot support
QSPI-boot is supported on LS2088ARDB RevF board with LS2088A SoC.
LS2088ARDB RevF Board has limitation that QIXIS can not be accessed.
CONFIG_FSL_QIXIS is not enabled.

Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-05-23 09:38:55 -07:00
Priyanka Jain
5193405a16 board: freescale: ls2080ardb: Enable SD interface for RevF board
LS2080ARDB/LS2088ARDB RevF board has smart voltage translator
which needs to be programmed to enable high speed SD interface
by setting GPIO4_10 output to zero.

Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-05-23 09:12:26 -07:00
Tom Rini
711391131c Merge git://git.denx.de/u-boot-sunxi
trini: Make Kconfig SPL_xxx entires only show if SPL, so that we don't
get Kconfig errors on platforms without SPL, ie sandbox (without SPL).

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-05-22 19:20:28 +00:00
Simon Glass
fc843a02ac Kconfig: Add a CONFIG_IDE option
At present IDE support is controlled by CONFIG_CMD_IDE. Add a separate
CONFIG_IDE option so that IDE support can be enabled without requiring
the 'ide' command.

Update existing users and move the ide driver into drivers/block since
it should not be in common/.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-05-22 12:45:27 -04:00
Simon Glass
7a01f3c6f4 Convert CONFIG_CMD_HDMIDETECT to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_HDMIDETECT

Note that we cannot do 'default y if VIDEO' because this option is only
enabled for a small subset of mx6 boards. Also this command is is not a
great implementation (it doesn't use driver model).

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-05-22 12:45:22 -04:00
Simon Glass
551c393446 Convert CONFIG_CMD_HASH to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_HASH

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Rework slightly, enable on some boards again]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-05-22 12:38:15 -04:00
Simon Glass
51f2937036 Convert CONFIG_CMD_FUSE to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_FUSE

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-05-22 09:33:58 -04:00
Simon Glass
ea7971f705 Convert CONFIG_CMD_ESBC_VALIDATE to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_ESBC_VALIDATE

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-05-22 09:33:55 -04:00
Simon Glass
42e6f852dd Convert CONFIG_CMD_ENTERRCM to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_ENTERRCM

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-05-22 09:33:53 -04:00
Tom Rini
089df18bfe lib: move hash CONFIG options to Kconfig
Commit 94e3c8c4fd ("crypto/fsl - Add progressive hashing support
using hardware acceleration.") created entries for CONFIG_SHA1,
CONFIG_SHA256, CONFIG_SHA_HW_ACCEL, and CONFIG_SHA_PROG_HW_ACCEL.
However, no defconfig has migrated to it.  Complete the move by first
adding additional logic to various Kconfig files to select this when
required and then use the moveconfig tool.  In many cases we can select
these because they are required to implement other drivers.  We also
correct how we include the various hashing algorithms in SPL.

This commit was generated as follows (after Kconfig additions):

[1] tools/moveconfig.py -y SHA1 SHA256 SHA_HW_ACCEL
[2] tools/moveconfig.py -y SHA_PROG_HW_ACCEL

Note:
We cannot move SHA_HW_ACCEL and SHA_PROG_HW_ACCEL simultaneously
because there is dependency between them.

Cc: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Cc: Naveen Burmi <NaveenBurmi@freescale.com>
Cc: Po Liu <po.liu@freescale.com>
Cc: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Cc: Priyanka Jain <Priyanka.Jain@freescale.com>
Cc: Shaohui Xie <Shaohui.Xie@freescale.com>
Cc: Chunhe Lan <Chunhe.Lan@freescale.com>
Cc: Chander Kashyap <k.chander@samsung.com>
Cc: Steve Rae <steve.rae@raedomain.com>
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: Feng Li <feng.li_2@nxp.com>
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Sumit Garg <sumit.garg@nxp.com>
Cc: Mingkai Hu <Mingkai.Hu@freescale.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Akshay Saraswat <akshay.s@samsung.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-05-22 08:36:58 -04:00
Ley Foon Tan
0680f1b1f7 Convert CONFIG_SPL_BOARD_INIT to Kconfig
This converts the following to Kconfig:
   CONFIG_SPL_BOARD_INIT

Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
[trini: Update the Kconfig logic]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-05-22 07:29:48 -04:00
Nobuhiro Iwamatsu
16071b1ba1 ARM: rmobile: Move address of IICDVFS(I2C) to rcar-gen3-base.h
The IICDVFS(I2C) set in r8a7796.h is common in rcar-gen3.
This moves CONFIG_SYS_I2C_SH_BASE0 in rcar-gen3-base.h.

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-05-22 15:07:31 +09:00
Marek Vasut
2aef8f32b6 ARM: rmobile: Allow R8A7796 Salvator-X configuration
The Salvator-X can have both H3 and M3 CPU on it, drop the
select R8A7795 to allow both configurations.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-05-22 04:38:26 +09:00
Marek Vasut
2dea3b3e7b ARM: rmobile: Add R8A7796 support
Add Kconfig entry for the R8A7796 RCar M3 SoC.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-05-22 04:38:26 +09:00
Marek Vasut
e965c89008 ARM: rmobile: Handle R8A7796 r1.1 in the PRR code
The R8A7796 r1.1 reports itself as r2.0 , add quirk into the
PRR code to fix this report.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-05-22 04:38:26 +09:00
Marek Vasut
bc271a0051 ARM: rmobile: Add R8A7796 into the CPU table
Add entry for the R8A7796 RCar M3 SoC into the CPU info table.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-05-22 04:38:25 +09:00
Marek Vasut
3a38c7d0d8 ARM: rmobile: Add R8A7795 into the CPU table
Add entry for the R8A7795 RCar H3 SoC into the CPU info table.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-05-22 04:38:25 +09:00
Marek Vasut
a0f6404649 ARM: rmobile: Make the Gen3 SoC configurable
Allow selecting the Gen3 SoC in preparation for RCar M3 .
No functional change.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-05-22 04:38:25 +09:00
Marek Vasut
1b044aa8c5 ARM: rmobile: Zap RCAR_GEN3_EXTRAM_BOOT
This Kconfig option is not used on any board, so drop it.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-05-22 04:38:25 +09:00
Marek Vasut
8d31fe2a64 ARM: rmobile: Import R8A7796 PFC and GPIO tables
Import the R8A7796 PFC and GPIO tables from the latest 3.5.3 release
from Renesas .

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-05-22 04:38:25 +09:00
Marek Vasut
0dfc2392f6 ARM: rmobile: Update R8A7795 PFC and GPIO tables
Sync the PFC and GPIO tables with the latest 3.5.3 release from
Renesas . This adds ES2.0 support.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-05-22 04:38:25 +09:00
Tom Rini
a375ff8e14 Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2017-05-18 17:17:45 -04:00
Tom Rini
753a4dde97 Merge branch 'master' of git://git.denx.de/u-boot-socfpga 2017-05-18 17:17:42 -04:00
Jean-Jacques Hiblot
ad99abe8e7 ARM: dts: am335x-evm: disable mmc3
SDIO is not supported in u-boot, there is no point in enabling mmc3.
For this purpose, add u-boot specific dtsi that this will be included
automatically while building the dtb.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-05-18 17:17:11 -04:00
Ley Foon Tan
d89e979c42 arm: socfpga: Enable build for Arria 10
Update Kconfig and Makefile to enable Arria 10.
Clean up Makefile and sorting *.o alphanumerically.

Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2017-05-18 11:33:19 +02:00
Ley Foon Tan
8f4c80c4fd arm: socfpga: Add SPL support for Arria 10
Add SPL support for Arria 10.

Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2017-05-18 11:33:18 +02:00
Ley Foon Tan
3d5f7c5af3 arm: dts: Add dts and dtsi for Arria 10
Device tree files for Arria 10

Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2017-05-18 11:33:18 +02:00
Ley Foon Tan
35b9800ff2 arm: socfpga: Add misc support for Arria 10
Add misc support for Arria 10.

Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2017-05-18 11:33:18 +02:00
Ley Foon Tan
caf36e1edb arm: socfpga: Add pinmux for Arria 10
Add pinmux support for Arria 10.

Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2017-05-18 11:33:18 +02:00
Ley Foon Tan
c887d48017 arm: socfpga: Add sdram header file for Arria 10
Add sdram header file for Arria 10.

Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2017-05-18 11:33:18 +02:00
Ley Foon Tan
86f032e630 arm: socfpga: Add system manager for Arria 10
Add system manager register struct and macros for Arria 10.

Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2017-05-18 11:33:18 +02:00
Ley Foon Tan
177ba1f927 arm: socfpga: Add clock driver for Arria 10
Add clock driver support for Arria 10.

Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2017-05-18 11:33:17 +02:00
Ley Foon Tan
827e6a7e0d arm: socfpga: Add reset driver support for Arria 10
Add reset driver support for Arria 10.

Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2017-05-18 11:33:17 +02:00
Ley Foon Tan
d83b8193ad arm: socfpga: Add A10 macros
Add i2c, timer and other A10 macros.

Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2017-05-18 11:33:17 +02:00
Ley Foon Tan
d1c559af5f arm: socfpga: Restructure misc driver
Restructure misc driver in the preparation to support A10.
Move the Gen5 specific code to gen5 file.

Change all uint32_t_to u32.

Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2017-05-18 11:33:17 +02:00
Ley Foon Tan
4ddd541d6c arm: socfpga: Restructure system manager
Restructure system manager in the preparation to support A10.
No functional change.

Change uint32_t to u32.

Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2017-05-18 11:33:17 +02:00
Ley Foon Tan
2b09ea48dd arm: socfpga: Restructure reset manager driver
Restructure reset manager driver in the preparation to support A10.
Move the Gen5 specific code to gen5 files.

Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2017-05-18 11:33:17 +02:00
Ley Foon Tan
de77811589 arm: socfpga: Restructure clock manager driver
Restructure clock manager driver in the preparation to support A10.
Move the Gen5 specific code to _gen5 files.

- Change all uint32_t to u32 and change to use macro BIT(n) for bit shift.
- Check return value from wait_for_bit(). So change return type to int for
  cm_write_with_phase() and cm_basic_init().

Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2017-05-18 11:33:16 +02:00
Peng Fan
e02ec19f4d arm: dts: imx7d-sdb: add usdhc support
Add usdhc support

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2017-05-18 11:24:34 +02:00
Peng Fan
00ad3a9f73 arm: dts: imx7d-sdb: add i2c support
Add i2c support.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2017-05-18 11:24:34 +02:00
Peng Fan
63f3401d23 arm: dts: imx7d-sdb: add regulator node for usb and mmc
Add regulator node for usb and mmc.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2017-05-18 11:24:34 +02:00
Peng Fan
9880eed8bd arm: dts: imx7d-sdb: add spi gpio node
Add spi gpio node for 74LV595.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2017-05-18 11:24:34 +02:00
Peng Fan
896d2e82e6 arm: dts: imx7d-sdb add basic dts
Add basic dts for i.MX7D-SDB board.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2017-05-18 11:24:33 +02:00
Peng Fan
993274f485 arm: dts: imx7: sync with Linux
Sync with Linux commit 308ac756("Merge tag 'gpio-v4.11-3'").

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefan Agner <stefan.agner@toradex.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2017-05-18 11:24:33 +02:00
Jagan Teki
671f458aae i.MX6UL: geam6ul: Add SETUP_IOMUX_PADS
Add generic SETUP_IOMUX_PADS function, for imx6ul mux pads.

Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-05-18 11:23:31 +02:00
Jagan Teki
bc1fe9006d icorem6: Make SPL to pick suitable fdt
SPL FIT is able to pick the suitable fdt file for u-boot,
so add that function through board_fit_config_name_match.

Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-05-18 11:23:31 +02:00
Jagan Teki
9786496cdc geam6ul: Add modeboot env via board_late_init
Add runtime, modeboot env which is setting mmcboot, or
nandboot based on the bootdevice so-that conditional
macros b/w MMC and NAND for CONFIG_BOOTCOMMAND should
be avoided in config files.

Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-05-18 11:23:31 +02:00
Jagan Teki
98f5661033 icorem6: Add modeboot env via board_late_init
Add runtime, modeboot env which is setting mmcboot, or
nandboot based on the bootdevice so-that conditional
macros b/w MMC and NAND for CONFIG_BOOTCOMMAND should
be avoided in config files.

Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-05-18 11:23:31 +02:00
Peng Fan
354fa86710 imx-common: rdc-sema: correct return value
When unlock, if caller is not the sema owner,
return -EACCES, not 1.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2017-05-18 11:23:31 +02:00
Peng Fan
2096da452b imx-common: timer: clean up
Drop the unneeded code. lib/time.c use timebase_l/h.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2017-05-18 11:23:31 +02:00
Siarhei Siamashka
7f0ef5a945 sunxi: Store the device tree name in the SPL header
This patch updates the mksunxiboot tool to optionally add
the default device tree name string to the SPL header. This
information can be used by the firmware upgrade tools to
protect users from harming themselves by trying to upgrade
to an incompatible bootloader.

The primary use case here is a non-removable bootable media
(such as NAND, eMMC or SPI flash), which already may have
a properly working, but a little bit outdated bootloader
installed. For example, the user may download or build a
new U-Boot image for "Cubieboard", and then attemept to
install it on a "Cubieboard2" hardware by mistake as a
replacement for the already existing bootloader. If this
happens, the flash programming tool can identify this
problem and warn the user.

The size of the SPL header is also increased from 64 bytes
to 96 bytes to provide enough space for the device tree name
string.
[Andre: split patch to remove OF_LIST hash feature]

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2017-05-17 23:23:58 +05:30
Andre Przywara
d29adf8eef sunxi: enable automatic FIT build for 64-bit SoCs
The Allwinner SoCs with 64-bit cores use an ARM Trusted Firmware binary,
which needs to be loaded alongside U-Boot proper.
Set the respective Kconfig options to let them select this feature and
also automatically build the FIT image.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[Rename Kconfig path to arch/arm/mach-sunxi/Kconfig]
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-05-17 23:23:25 +05:30
Andre Przywara
98db26a612 armv8: fsl: move ccn504 code into FSL Makefile
The generic ARMv8 assembly code contains routines for setting up
a CCN interconnect, though the Freescale SoCs are the only user.
Link this code only for Freescale targets, this saves some precious
bytes in the chronically tight SPL.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2017-05-17 23:20:50 +05:30
Andre Przywara
0cef6cbe3a armv8: SPL: only compile GIC code if needed
Not every SoC needs to set up the GIC interrupt controller, so link
think code only when the respective config option is set.
This shaves off some bytes from the SPL code size.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-05-17 23:20:31 +05:30
Masahiro Yamada
81afa9c9a3 ARM: uniphier: add more init code for PXs3
Add the boot device table and reset deassertion for eMMC.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-05-17 21:56:17 +09:00
Masahiro Yamada
abb6ac25da ARM: dts: uniphier: sync DT with Linux
Fix the following DTC warnings:
Warning (simple_bus_reg): Node /soc/system-bus@58c00000/support_card@1,1f00000/ethernet@00000000 simple-bus unit address format error, expected "0"
Warning (simple_bus_reg): Node /soc/system-bus@58c00000/support_card@1,1f00000/uart@000b0000 simple-bus unit address format error, expected "b0000"
Warning (simple_bus_reg): Node /soc/smpctrl@59800000 simple-bus unit address format error, expected "59801000"

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-05-17 21:51:04 +09:00
Masahiro Yamada
45f41c134b ARM: uniphier: add weird workaround code for LD20
When booting from ARM Trusted Firmware, U-Boot runs in EL1-NS.
The boot flow is as follows:
  BL1 -> BL2 -> BL31 -> BL33 (i.e. U-Boot)

This boot sequence works fine for LD11 SoC (Cortex-A53), but LD20
SoC (Cortex-A72) hangs in U-Boot.  The solution I found is to
read sctlr_el1 and write back the value as-is.  This should be
no effect, but surprisingly fixes the problem for LD20 to boot.
I do not know why.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-05-17 21:50:31 +09:00
Masahiro Yamada
c5bd411f6c ARM: uniphier: fix MODEL field of REVISION register
The MODEL field is 3 bit wide.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-05-17 21:46:14 +09:00
Tom Rini
4125bbcef6 Merge branch 'master' of git://git.denx.de/u-boot-mmc
- Add #undef CONFIG_DM_MMC_OPS to omap3_logic in the SPL build case, to
  match other TI platforms in the same situation.

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-05-16 08:10:50 -04:00
Tom Rini
d09ec7f816 Merge branch 'master' of git://git.denx.de/u-boot-video 2017-05-15 20:16:02 -04:00
Jernej Skrabec
940aed8f6b sunxi: Add clock support for TV encoder
This patch adds support for TV encoder clocks which will be used later.

Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
2017-05-15 21:22:57 +02:00
Jernej Skrabec
c10806267d sunxi: video: Split out TVE code
Newer SoCs use same TV encoder unit. Split it out so it can be reused
with new DM video driver.

Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-15 21:22:24 +02:00
Tom Rini
cb33bda44f Merge branch 'master' of git://git.denx.de/u-boot-i2c 2017-05-15 13:01:26 -04:00
Tom Rini
80f1f3204a Kconfig: USB: Migrate existing USB_EHCI_xxx options
The following options are migrated over fully now:
- USB_EHCI_ATMEL
- USB_EHCI_MARVELL
- USB_EHCI_MX6
- USB_EHCI_MX7
- USB_EHCI_MSM
- USB_EHCI_ZYNQ
- USB_EHCI_GENERIC

This also requires fixing the depends on USB_EHCI_MARVELL as it's used
by Orion5X and Kirkwood as well.

Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marek Vasut <marex@denx.de>
2017-05-15 13:00:26 -04:00
Tom Rini
8850c5d57c Kconfig: USB: Migrate CONFIG_USB_EHCI to CONFIG_USB_EHCI_HCD
In order to be able to migrate the various SoC EHCI CONFIG options we
first need to finish the switch from CONFIG_USB_EHCI to
CONFIG_USB_EHCI_HCD.

Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marek Vasut <marex@denx.de>
2017-05-15 10:40:05 -04:00
Tom Rini
302acbede9 omap: Drop CONFIG_OMAP_VC_I2C_HS_MCODE
The symbol CONFIG_OMAP_VC_I2C_HS_MCODE always uses the default value.
Restructure the comment and code such that if a need arises later to use
another value we can address this then.

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-05-15 10:40:03 -04:00
Tom Rini
68ccab5193 omap3: Migrate CONFIG_OMAP3_GPIO_X to Kconfig
The symbols CONFIG_OMAP3_GPIO_X control if we enable the clocks for a
given GPIO bank in U-Boot.  select the required banks for each target.
In some cases we need to also migrate from CONFIG_USB_EHCI (deprecated,
in include/configs/) to CONFIG_USB_EHCI_HCD as we only require the GPIO
bank to be enabled if USB is also enabled.

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-05-15 10:40:00 -04:00
Tom Rini
d87f82967f omap5: Migrate CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC to Kconfig
While in theory this value could be used in places outside of "omap5"
(such as OMAP4), we only make use of it today in OMAP5, so place the
Kconfig entry there.  Given that Kconfig lets us provide a default, we
drop CONFIG_DEFAULT_OMAP_RESET_TIME_MAX_USEC entirely.  The contents of
doc/README.omap-reset-time make a good help entry, so adjust them
slightly and delete the file.  Move the comment about range to where we
use the value now, and have Kconfig enforce the upper bound.

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-05-15 10:39:57 -04:00
Tom Rini
89024ddc9e TI: Drop 'CONFIG_OMAP'
In the two cases in the code where we use CONFIG_OMAP as a useful test
currently we can make use of CONFIG_ARCH_OMAP2PLUS instead.  With that
changed we can drop all defines of CONFIG_OMAP.  While in here,
CONFIG_OMAP3430 is only defined and then never used, so drop.

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-05-15 10:39:56 -04:00
Tom Rini
9ed8e4a3af arch/arm/cpu/arm926ejs/omap: Remove
This code has been unused since the removal of the "omap2" platforms,
remove.

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-05-15 10:39:55 -04:00
Dinh Nguyen
9ad7147b8d armv8: minor fix to comment for enabling SMPEN bit
The SMPEN bit is located in the cpuectlr_el1 register and not the
cpuactlr_el1 register. Adjust the comment accordingly and also fix
a spelling error.

Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
CC: Mingkai Hu <mingkai.hu@nxp.com>
CC: Gong Qianyu <Qianyu.Gong@nxp.com>
CC: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
CC: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
CC: York Sun <york.sun@nxp.com>
CC: Albert Aribaud <albert.u.boot@aribaud.net>
CC: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-05-15 10:38:04 -04:00
Masahiro Yamada
4aa2ba3a34 mmc: replace CONFIG_GENERIC_MMC with CONFIG_MMC
Now CONFIG_GENERIC_MMC and CONFIG_MMC match for all defconfig.
We do not need two options for the same feature.  Deprecate the
former.

This commit was generated with the sed script 's/GENERIC_MMC/MMC/'
and manual fixup of drivers/mmc/Kconfig.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-05-15 18:28:23 +09:00
Simon Glass
eb5ba3aefd i2c: Drop use of CONFIG_I2C_HARD
This option is pretty old. It predates CONFIG_SYS_I2C which is itself
deprecated in favour of driver model. Disable it for all boards.

Also drop I2C options which depend on this.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-05-15 06:17:09 +02:00
Peng Fan
8fbbb6c27f arm: change tbu/l type to unsigned int
Change tbu/l type to unsigned int.
>From the timer file for arm,
"(((unsigned long long)gd->arch.tbu) << 32) | gd->arch.tbl;" is used,
This piece code is based on tbu/tbl is 32bits, so change the type to
unsigned int.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
2017-05-12 08:37:34 -04:00
Tom Rini
80403aa636 rk3036: Fix unused variable warning
The variable grf is only referenced if EARLY_DEBUG is defined so move the
declaration to be under the existing guard.

Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-12 08:37:22 -04:00
Lokesh Vutla
878d885620 arm: amx3xx: Add support for early debug
For early debug, the following configs needs to be enabled:

CONFIG_DEBUG_UART=y
CONFIG_DEBUG_UART_OMAP=y
CONFIG_DEBUG_UART_BASE=0x44e09000
CONFIG_DEBUG_UART_CLOCK=48000000
CONFIG_DEBUG_UART_SHIFT=2
CONFIG_DEBUG_UART_ANNOUNCE=y

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-05-12 08:37:15 -04:00
Lokesh Vutla
01fe1199d6 arm: omap5+: Add support for early debug
For early debug, the following configs needs to be enabled:

CONFIG_DEBUG_UART=y
CONFIG_DEBUG_UART_OMAP=y
CONFIG_DEBUG_UART_CLOCK=48000000
CONFIG_DEBUG_UART_SHIFT=2
CONFIG_DEBUG_UART_ANNOUNCE=y

For DRA7xx:
CONFIG_DEBUG_UART_BASE=0x4806a000

For AM57xx:
CONFIG_DEBUG_UART_BASE=0x48020000

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-05-12 08:37:15 -04:00
Lokesh Vutla
fbd6295da4 arm: am33xx: Add support for mulitiple PLL input frequencies
am335x supports various sysclk frequencies which can be determined
using sysboot pins. PLLs should be configures based on this
sysclk frequency. Add PLL configurations for all supported
frequencies.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-05-12 08:37:14 -04:00
Lokesh Vutla
59041a5084 arm: am33xx: Fix MPU opp selection
Update MPU frequencies and voltages as per the latest
DM[1] dated: OCT 2011 Revised APRIL 2016, Section 5.4.
Below is the consolidated data:

MPU values for PG 2.0 and later(Package ZCZ and ZCE):

 -------------------------------------------------------
|	|	  ZCZ		|	  ZCE		|
|-------------------------------------------------------|
|	| VDD[V]   | ARM [MHz]	| VDD[V]   | ARM [MHz]  |
|-------|----------|------------|----------|------------|
| NITRO |  1.325   |   1000     |   NA     |    NA      |
|-------|----------|------------|----------|------------|
| TURBO |   1.26   |    800	|   NA     |    NA      |
|-------|----------|------------|----------|------------|
|OPP120 |   1.20   |    720     |   NA     |    NA      |
|-------|----------|------------|----------|------------|
|OPP100 |   1.10   |    600     |   1.10   |    600     |
|-------|----------|------------|----------|------------|
| OPP50 |   0.95   |    300     |   0.95   |    300     |
 -------------------------------------------------------

There is no eFuse blown on PG1.0 Silicons due to which there is
no way to detect the maximum frequencies supported. So default
to OPP100 for which both frequency and voltages are common on both
the packages.

[1] http://www.ti.com/lit/ds/symlink/am3356.pdf

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-05-12 08:37:12 -04:00
Lokesh Vutla
c187dd685a configs: convert CONFIG_SYS_MPUCLK to Kconfig
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-05-12 08:37:11 -04:00
Vikas Manocha
624b7101ee stm32f7: configure mpu valid for f7 family
This configuration should be valid for all F7 family devices in general.
Here is the regions info:

	- Region0 : 4GB	  : cacheable & executable.
	- Region1 : 512MB : text area	: strogly ordered & executable.
	- Region2 : 512MB : peripherals : device memory & non-executable.
	- Region3 : 512MB : peripherals : device memory & non-executable.
	- Region4 : 512MB : cortexM area: strongly ordered & non-executable.

Higher region number overrides the lower region configuration.

Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
2017-05-12 08:37:08 -04:00
Vikas Manocha
33b78476d2 stm32: use armv7m MPU configuration support
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
2017-05-12 08:37:07 -04:00
Vikas Manocha
96b61ab15c armv7m: add MPU configuration support
Cortex-M archs support option memory protection unit (MPU). MPU is used
to set the memory types, attributes, access permissions for different regions,
cache policies of the device.

e.g. using MPU it is possible to configure memory region as device memory
or strongly ordered, memory attributes like execute never, cache policies
like write-back or write-through.

Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
2017-05-12 08:37:06 -04:00
Vikas Manocha
df951c4039 armv7m: correct mpu region size define for 8MB size
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
2017-05-12 08:37:05 -04:00
Vikas Manocha
4098d2061f arvm7m: add cleanup before linux booting
Data cache memory needs to be disabled before handing over control to
linux kernel. This patch populates the cleanup_before_linux stub.

Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
2017-05-12 08:36:52 -04:00
Vikas Manocha
a0ee014f1b armv7m: cache: add flush & invalidate all dcache
Add functionality to flush & invalidate all the dcache using the
prototype declared in common header file.

Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
[trini: Add dummy functions for the not-enabled case]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-05-12 08:19:14 -04:00
Lokesh Vutla
a292eb6702 arm: am335x: Enable tiny printf in SPL
am335x_evm SPL is very close to its limit in SRAM space.
Switch to use tiny printf to reclaim some size.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-05-11 22:21:29 -04:00
Lokesh Vutla
238205f1b3 configs: am335x_evm: Enable SPL_DM
Enable SPL_DM on all AM335x based TI platforms.

http://patchwork.ozlabs.org/patch/751300/
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-05-11 22:21:29 -04:00
Lokesh Vutla
3a517fdc2b configs: am335x_evm: Use omap2 generic spl load script
No reason to use a separate load script for am33xx than using
omap-common load script.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-05-11 22:21:28 -04:00
Lokesh Vutla
2558c04906 dm: mmc: omap_hsmmc: Update to support of-platdata
This is to aid platforms that uses OF_PLATDATA.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-05-11 22:21:27 -04:00
B, Ravi
984a3c8777 spl: fdt: support for fdt fixup for falcon boot
Adding support for fdt fixup to update the
memory node in device tree for falcon boot.

This is needed for single stage or falcon
bootmode, to pass memory configuration to
kernel through DT memory node.

Signed-off-by: Ravi Babu <ravibabu@ti.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
2017-05-11 22:04:26 -04:00
Lokesh Vutla
86282798b0 arch: arm: omap: Declare size of ddr very early
Declare the size of ddr very early in spl, so that this can be
used to enable cache.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Ravi Babu <ravibabu@ti.com>
2017-05-11 22:03:41 -04:00
Simon Glass
6775a8208e arm: Support cache invalidate
At present there is not operation to invalidate a cache range. This seems
to be needed to fill out the cache operations. Add an implementation based
on the flush operation.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-05-11 22:03:39 -04:00
Simon Glass
f97cae9575 arm: Correct signature for get_ticks()
This should be uint64_t to match its definition in common.h. Fix it.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-05-11 22:03:38 -04:00
Tom Rini
1f5541c881 Merge git://git.denx.de/u-boot-rockchip
This adds a new firefly-rk3399 board, MIPI support for rk3399 and
rk3288, rk818 pmic support, mkimage improvements for rockchip and a few
other things.
2017-05-10 17:40:11 -04:00
Tom Rini
102d86552a Merge branch 'master' of git://git.denx.de/u-boot-mips 2017-05-10 15:50:21 -04:00
Eric Gao
2085de57f3 rockchip: dts: evb_rk3288: Add mipi display support
Add mipi dsi configuration for evb-rk3288 device tree.

Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-10 13:37:22 -06:00
Eric Gao
9b534ba001 rockchip: rk3288: grf: Add grf define for mipi dsi
Add grf register define for rk3288 mipi dsi

Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-10 13:37:22 -06:00
Eric Gao
df8fe99cf2 rockchip: dts: Add mipi dsi support for rk3399
Add dts config for mipi display, include vop, mipi controller, panel, backlight
. And Enable rk808 for lcd_3v3 in another patch.

Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-05-10 13:37:22 -06:00
Eric Gao
9f819931e0 rockchip: video: vop: Add mipi display mode for rk3399
Add mipi display mode for rk3399 vop, so that we can use mipi panel
for display.

Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-10 13:37:22 -06:00
Eric Gao
1c3984041c rockchip: video: Add mipi driver support for rockchip soc
Add basic driver for mipi display on rockchip soc platform.

Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
2017-05-10 13:37:22 -06:00
Eric Gao
858f6368af rockchip: include: grf: Add GRF register declaration for mipi dsi
Add GRF register declaration for mipi dsi.

Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-05-10 13:37:22 -06:00
Jacob Chen
453c5a927c power: rk808: rename to rk8xx
Since this driver can be used for rk8xx series pmic,
let's rename rk808 to rk8xx, to make it clear.

Configs parts are done by sed -i "s/RK808/RK8XX/g" `grep RK808 -lr ./`

Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
2017-05-10 13:37:22 -06:00
Jonas Karlman
ecc3bd73b3 rockchip: tinker: set ethaddr in late init
Set ethernet mac address in late init for Tinker Board,
prevents getting a random mac address each boot.

Read mac address from eeprom, first 6 bytes from m24c08@50.
Same as /etc/init.d/rockchip.sh on Tinker OS.

Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-10 13:37:22 -06:00
Philipp Tomsich
26e2e404b7 rockchip: pinctrl: rk3399: add support for the HDMI I2C pins
To add HDMI support for the RK3399, this commit provides the needed
pinctrl functionality to configure the HDMI I2C pins (used for reading
the screen's EDID).

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-10 13:37:21 -06:00
Kever Yang
a66726838e rockchip: dts: add rk3399-firefly dts
Firefly-rk3399 is a bord from T-Firefly, you can find detail about
it here:
http://en.t-firefly.com/en/firenow/Firefly_RK3399/

This patch add basic node for the board and make it able to bring
up.

Peripheral/interfaces on board:
- usb hub which connect to ehci controller;
- UART2 debug
- eMMC
- PCIe
- USB 3.0 HOST, type-C port
- sdio, sd-card
- HDMI
- Ethernet
- OPTICAL
- WiFi/BT
- MIPI CSI/DSI
- IR
- EDP/DP

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-10 13:37:21 -06:00
Kever Yang
dde2223372 rockchip: dts: rk3399: sync with kernel dts
The kernel dts has update a lot since the first time we commit rk3399.dtsi,
sync with kernel for further development.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
2017-05-10 13:37:21 -06:00
Kever Yang
fa1392a236 rockchip: reserve memory for rk3399 ATF data
There are 3 regions used by rk3399 ATF:
- bl31 code, located at 0x10000;
- cortex-m0 code and data, located at 0xff8c0000;
- bl31 data, located at 0xff8c1000 ~ 0xff8c4000;

SPL_TEXT_BASE starts from 0xff8c2000, we need to reserve memory
for ATF data, or else there will be memory corrupt after SPL
loads the ATF image.

More detail about cortex-M0 code in ATF:
https://github.com/ARM-software/arm-trusted-firmware/commit/
8382e17c4c6bffd15119dfce1ee4372e3c1a7890

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
2017-05-10 13:37:21 -06:00
Kever Yang
602778d3c7 rockchip: pinctrl: rk3399: add gmac io strength support
GMAC controller need to init the tx io driver strength to 13mA,
just like the description in dts pinctrl node, or else the controller
may only work in 100MHz Mode, and fail to work at 1000MHz mode.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com <mailto:philipp.tomsich@theobroma-systems.com>>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-10 13:37:21 -06:00
Kever Yang
fd9884e292 rockchip: dts: evb-rk3399: add gmac support
Enable gmac for evb-rk3399.

Change-Id: I85e35667e08e22e38577e63eb0e65731fc9c69b6
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2017-05-10 13:37:21 -06:00
Kever Yang
76e1693b9b rockchip: rk3399: use actual dram size
Since our sdram driver is ready, we can use the actual size
instead of hard code.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
2017-05-10 13:37:21 -06:00
Eddie Cai
7474bbe857 rockchip: enable debug uart
enable debug uart for rk3288 and print something to let people know
where we are

Signed-off-by: Eddie Cai <eddie.cai.linux@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-10 13:37:21 -06:00
Kever Yang
26b1edf4ce rockchip: dts: evb-rk3399: correct pwm3 polarity
The pwm3 on evb-rk3399 is used for pwm regulator, need to invert
the polarity to make it work correctly.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
2017-05-10 13:37:21 -06:00
Philipp Tomsich
572045b6e7 rockchip: dts: rk3399-puma: Add DDR3-1600 timings and use for Puma
With the validation done for DDR3-1600 (i.e. 800 MHz bus clock), we
add the timings (rk3399-sdram-ddr3-1600.dtsi) and change rk3399-puma.dts
to use these by default.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
Drop blank line at end of file:
Signed-off-by: Simon Glass <sjg@chromium.org>
2017-05-10 13:37:21 -06:00
Philipp Tomsich
c5f99c654e rockchip: dts: Clean up graffiti in rk3399-sdram-ddr3-1333.dtsi
The DDR3-1333 timings for the RK3399-Q7 (Puma) has some unintended
left-over comments in them. This change cleans the file up.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
2017-05-10 13:37:21 -06:00
Philipp Tomsich
315e6a38f9 rockchip: pinctrl: rk3399: add support for the SPI5 controller
This commit adds support for the pin-configuration of the SPI5
controller of the RK3399 through the following changes:
 * grf_rk3399.h: adds definition for configuring the SPI5 pins
   		 in the GPIO2C group
 * periph.h: defines PERIPH_ID_SPI3 through PERIPH_ID_SPI5
 * pinctrl_rk3399.c: adds the reverse-mapping from the IRQ# to
   		     PERIPH_ID_SPI5; dispatches PERIPH_ID_SPI3
		     through SPI5 to the appropriate pin-config
		     function; implements the pin-configuration
		     for PERIPH_ID_SPI5 using the GPIO2C group

X-AffectedPlatforms: RK3399-Q7
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Jakob Unterwurzacher <jakob.unterwurzacher@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
2017-05-10 13:37:21 -06:00
Kever Yang
90c9127e47 rockchip: rk3399: correct memory region
RK3399 device memory region is 0xf8000000~0xffffffff.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-10 13:37:21 -06:00
Álvaro Fernández Rojas
d57259b950 u-boot.elf: remove hard-coded arm64 flags
This is needed in order to allow building it for other archs.
Move relocation comment to a better place.
Remove no longer needed dts FIXME.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-05-10 16:16:09 +02:00
Adam Ford
7815c709ab power: twl4030: Move CONFIG_TWL4030_POWER to Kconfig
As requested, I added the CONFIG_TWL4030_POWER to Kconfig and made it
the implied default when selecting OMAP34XX as a platform.

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-09 20:35:38 -04:00
Adam Ford
15fde737fc omap3_logic: Add Device Tree Support and more DM drivers
This patch also removes all the excessive code for NS16550 intiailization
as the device tree can do that now.  This also adds DM_I2C and DM_MMC
since the overlying drivers have the built-in support already.  The
corresponding include/config/omap3_logic.h also reduced in size
due to the new device tree support.

Signed-off-by: Adam Ford <aford173@gmail.com>

Changes in V2:
  Retain Auto-detect ability between SOM-LV and Torpedo
  Split this off from the device sub submissions
2017-05-09 20:35:38 -04:00
Adam Ford
4c8a9f2311 ARM: DTS: Add Logic PD DM3730 Torpedo Device Tree
Previous commit has this combined with SOM-LV.  This commit has only
the Torpedo Device Tree.

The device trees were sync'd with 4.9.y stable with two changes:
disable mmc2 and stdout-path = &uart1.  Both of those two changes
will be submitted to the linux-omap list

Signed-off-by: Adam Ford <aford173@gmail.com>

Changes in V2:
  Split device tree from other board
2017-05-09 20:35:37 -04:00
Adam Ford
063da122e0 ARM: DTS: Add Logic PD DM3730 SOM-LV initial support
This adds the device tree.  Previous commit added both boards at the
same time.

Signed-off-by: Adam Ford <aford173@gmail.com>

Changes in V2:
  Split the SOM-LV from Torpedo
2017-05-09 20:35:37 -04:00
Adam Ford
65ee2f3c33 OMAP3: Add SMSC9221 device tree for omap devices connected on GPMC.
Some OMAP3 devices support an SMSC ethernet PHY connected to the GPMC bus.
This copies this device tree from Linux 4.9.y stable

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-05-09 20:35:37 -04:00
Adam Ford
c9ff04fdc8 omap3: Copy twl4030 device tree from Linux 4.9.y stable
Many OMAP3 boards use a TWL4030 PMIC.  This brings in the related
device tree information for common TWL4030 and TWL4030 with OMAP3.

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-05-09 20:35:36 -04:00
Adam Ford
cac4d6a680 omap3630: Copy Device tree from Linux 4.9.y stable
Add device tree support to allow for CONFIG_OF_CONTROL in OMAP3630 boards.
DM3730 can use this same device tree.

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-05-09 20:35:36 -04:00
Adam Ford
1932145728 omap3: Copy Device tree from Linux 4.9.y stable
Add device tree support to allow for CONFIG_OF_CONTROL in OMAP3 boards.

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-05-09 20:35:35 -04:00
Adam Ford
46831c1a4c omap_hsmmc: update struct hsmmc to accommodate omap3 from DT
This patch changes the way DM_MMC calculates offset to the base register of
MMC. Previously this was through an #ifdef but that wasn't necessary for OMAP3.

This patch will now add in the offset to the base address based on the
.compatible flags.

Signed-off-by: Adam Ford <aford173@gmail.com>

V2: Remove ifdef completely and reference offset from the omap_hsmmc_ids table.

V1: Change ifdef to ignore OMAP3
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-09 20:35:35 -04:00
Paolo Pisati
45a6d231b2 bcm2835_wdt: support for the BCM2835/2836 watchdog
Signed-off-by: Paolo Pisati <p.pisati@gmail.com>
2017-05-09 20:30:08 -04:00
Simon Glass
7cac2fced7 video: arm: rpi: Move the video settings out of the driver
Add a function to set the video parameters to the msg handler and remove
it from the video driver.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
2017-05-09 20:20:40 -04:00
Simon Glass
2e4170b63b video: arm: rpi: Move the video query out of the driver
Add a function to get the video size to the msg handler and remove it from
the video driver.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
2017-05-09 20:20:39 -04:00
Simon Glass
c6606515f1 arm: rpi: Add a function to obtain the MMC clock
Move this code into the new message handler file.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-05-09 20:19:33 -04:00
Simon Glass
70997d88c4 arm: rpi: Add a file to handle messages
The bcm283x chips provide a way for the ARM core to communicate with the
graphics processor, which is in charge of many things. This is handled by
way of a message prototcol.

At present the code for sending message (and receiving a reply) is spread
around U-Boot, primarily in the board file. This means that sending a
message from a driver requires duplicating the code.

Create a new message implementation with a function to support powering on
a subsystem as a starting point.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-05-09 20:19:32 -04:00
Simon Glass
b59357464c arm: rpi: Drop the GPIO device addresses
We can rely on the device tree to provide this information.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-05-09 20:19:05 -04:00
Tom Rini
dd9999d5f4 Merge git://git.denx.de/u-boot-dm 2017-05-09 16:11:36 -04:00
Tom Rini
a284212963 Merge git://www.denx.de/git/u-boot-marvell 2017-05-09 15:48:09 -04:00
Jean-Jacques Hiblot
33a5e2c5e7 dra7: dtsi: mark ocp2scp bus compatible with "simple-bus"
This is needed to probe devices under that bus such as the SATA PHY.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-09 12:14:16 -06:00
Wenyou Yang
6cb2a7fe81 ARM: dts: at91: Add dts files for at91sam9263ek
The device tree source files of at91sam9263ek boards are copied from
the Linux v4.10, do the changes as below.
 - Add the reg property for the pinctrl node.
 - Move the gpio (pioA, pioB, pioC, pioD, pioE) nodes as the pinctrl's
   slibling nodes, instead of the child nodes.
 - Add the "u-boot,dm-pre-reloc" property for the dbgu node are used
   in board_init_f stage.
 - Fix the compilation warnings.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-09 12:14:15 -06:00
Wenyou Yang
1e315a356b ARM: dts: at91: Add dts files for at91sam9rlek
The device tree source files of at91sam9rlek boards are copied from
the Linux v4.10, do the changes as below.
 - Add the reg property for the pinctrl node.
 - Move the gpio (pioA, pioB, pioC, pioD) nodes as the pinctrl's
   slibling nodes, instead of the child nodes.
 - Add the "u-boot,dm-pre-reloc" property for the dbgu node are used
   in board_init_f stage.
 - Fix the compilation warnings.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-09 12:14:15 -06:00
Wenyou Yang
627e41f125 ARM: dts: at91: Add dts files for at91sam9260ek/9g20ek
The device tree source files of at91sam9g20ek and at91sam9260ek
boards are copied from the Linux v4.10, do the changes below.
 - Fix the build error for the usb0 node.
 - Add the reg property for the pinctrl node.
 - Move the gpio (pioA, pioB, pioC ...) nodes as the pinctrl's
   slibling nodes, instead of the child nodes.
 - Add the "u-boot,dm-pre-reloc" property for the dbgu node are used
   in board_init_f stage.
 - Add the clk pinctrl of the mmc0 node.
 - Fix the compilation warnings.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-09 12:14:15 -06:00
Wenyou Yang
eb6f87cc07 ARM: dts: at91: Add dts files for at91sam9m10g45ek
The device tree source files of at91sam9m10g45ek boards are copied
from the Linux v4.10, do the changes as below.
 - Add the reg property for the pinctrl node.
 - Move the gpio (pioA, pioB, pioC, pioD, pioE) nodes as the pinctrl's
   slibling nodes, instead of the child nodes.
 - Add the "u-boot,dm-pre-reloc" property to determine which nodes
   are used by the board_init_f stage.
 - Fix the compilation warnings.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-09 12:14:15 -06:00
Wenyou Yang
cd339347b9 ARM: dts: at91: Add dts files for at91sam9n12ek
The device tree source files of at91sam9n12ek boards are copied from
the Linux v4.10, do the changes as below.
 - Add the reg property for the pinctrl node.
 - Move the gpio (pioA, pioB, pioC, pioD) nodes as the pinctrl's
   slibling nodes, instead of the child nodes.
 - Change the compatible of the spi flash to "spi-flash".
 - Add the spi0 aliases.
 - Fix the pinctrl-names of mmc0 node.
 - Add the "u-boot,dm-pre-reloc" property to determine which nodes
   are used by the board_init_f stage.
 - Fix the compilation warnings.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-09 12:14:15 -06:00
Wenyou Yang
25e88d406e ARM: dts: at91: Add dts files for at91sam9x5ek
The device tree source files of at91sam9x5ek board are copied from
the Linux v4.10, do the changes below.
 - Add the reg property for the pinctrl node.
 - Move the gpio (pioA, pioB, pioC ...) nodes as the pinctrl's
   slibling nodes, instead of the child nodes.
 - Add the "u-boot,dm-pre-reloc" property to determine which nodes
   are used by the board_init_f stage.
 - Change the compatible of the spi flash to "spi-flash".
 - Add the spi0 aliases.
 - Fix the compilation warnings.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-09 12:14:15 -06:00
Wenyou Yang
0d00f9b6c1 board: sama5d4ek: fix DD2 configuration
Fix the DDR2 configuration to make SPL work.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
2017-05-09 12:14:15 -06:00
Wenyou Yang
4529ee3bc5 ARM: dts: sama5d2_xplained: update for SPL
Add the "u-boot,dm-pre-reloc" property to determine which nodes
which are needed by SPL and by the board_init_f stage.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
2017-05-09 12:14:15 -06:00
Wenyou Yang
20bb165c1f ARM: dts: sama5d2: add clock property for uart1 node
Add clock property for uart1 node.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
2017-05-09 12:14:15 -06:00
Chris Packham
e38f5fc8d8 ARM: mvebu: switch db-88f6820-amc to DM for i2c
Move existing configuration from header file to defconfig or dts as
appropriate.

Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
2017-05-09 13:38:18 +02:00
Stefan Roese
fdc9e88088 fix: phy: marvell: cp110: update comphy selector option
Align PHY selectors register with Armada-CP-110 functional SPEC
update all relevant device trees with this change.

Signed-off-by: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2017-05-09 13:38:18 +02:00
Stefan Roese
e89acc4bf1 phy: marvell: cp110: update utmi phy connection type
UTMI_PHY_TO_USB_HOST was used in USB3 UTMI dts node only, but there will
be USB2 UTMI dts node for some SoCs that have got USB2 controller, so rename
TO_USB_HOST to TO_USB3_HOST to distinguish TO_USB2_HOST in later on patches.

Signed-off-by: zachary <zhangzg@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2017-05-09 13:38:18 +02:00
Stefan Roese
cb686454c7 phy: marvell: Replace PHY_TYPE_KR with PHY_TYPE_SFI
Use correct naming as done in the latest Marvell U-Boot version as well.

Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2017-05-09 13:38:18 +02:00
Uwe Kleine-König
d374e90b27 arm: mvebu: Minor fixes in the AXP / A38x SERDES code
- Fix spelling error of SERDES_VERSION
- Remove superfluous definition of this macro
- Remove unnecessary include of i2c.h

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2017-05-09 13:38:18 +02:00
Konstantin Porotchkin
50eacd8eb1 arm64: a8k: dts: Add support for NAND devices on A8K platform
Add NAND to CP master device tree. Add armada-7040-db-nand
device tree for the board configured with NAND boot device.
Add comment about boot device ID to armada-7040-db DTS.

Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2017-05-09 13:38:18 +02:00
Konstantin Porotchkin
a2cb55938f arm64: mvebu: a8k: Add support for NAND clock get
Implement mvebu_get_nand_clock call for A8K family.
This function is used by PXA3XX NAND driver.

Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2017-05-09 13:38:18 +02:00
Konstantin Porotchkin
f4f194e864 arm64: mvebu: Trigger PCI devices scan at early init stage
Add PCIe initialization at early init stage.
This operation has a side effect of detecting all PCIe
plug-in cards, so the operator is not obligated to issue
"pci enum" command though CLI for this purpose.

Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2017-05-09 13:38:18 +02:00
Konstantin Porotchkin
0f712f2c8d mvebu: dts: a80x0: Sync the DB DTS with standard config A
Sync the default configuration of Armada-8040-DB with
Marvell u-boot-2015  standard configuration "A" for the same board.
The standard configuration "A" enables 2 PCIe slots on CP0
and 3 PCIe slots on CP1.
This is the main configuration used for u-boot  and Linux tests.
This patch also re-arranges the DTS file entries by grouping
all nodes related to CP0 and CP1.

Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2017-05-09 13:38:18 +02:00
Cooper Jr., Franklin
1743d040b1 ARM: keystone: Enable DM_I2C by default
Enable by default DM_I2C for all Texas Instruments Keystone 2 based
evms.

Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
2017-05-09 09:05:13 +02:00
Cooper Jr., Franklin
1eaa0b4ed6 ARM: dts: keystone-k2g-evm: Enable I2C0 and I2C1
Enable I2C0 and I2C1 which is needed to enable usage of DM I2C.

Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
2017-05-09 09:05:03 +02:00
Cooper Jr., Franklin
c7d45ff91d ARM: dts: keystone2: add I2C aliases for davinci I2C nodes
Add aliases for I2C nodes required for the DM framework to probe the
davinci-i2c driver.

Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
2017-05-09 09:04:55 +02:00