If CONFIG_SYS_I2C_S3C24X0_SLAVE isn't defined, then complie error should
be occurred.
This patch is for preventing it.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Adding additional compatible string for version 1.4 of the IP block.
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
0c0f719ad2 accidentally changed the
endianness of the i2c read and write addresses. This was noticable when
accessing EEPROMs that use 2 byte addressing as the LSB was being sent
first.
Signed-off-by: Bradley Bolen <bradleybolen@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Some I2C bus devicetree nodes, doesn't require to have
gpio pinctrl so replace the dev_info to debug so the
print never comes on the console and for bus that uses
gpio pinctrl anyway have dev_err.
Before:
------
U-Boot> i2c dev 1
Setting bus to 1
i2c bus 1 at 0x21a4000, no gpio pinctrl state.
After:
------
U-Boot> i2c dev 1
Setting bus to 1
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Heiko Schocher <hs@denx.de>
Better to print the hex value for bus address instead of
decimal, for more readbility on bus addressing.
Before:
------
U-Boot> i2c dev 1
Setting bus to 1
i2c bus 1 at 35274752, no gpio pinctrl state.
After:
------
U-Boot> i2c dev 1
Setting bus to 1
i2c bus 1 at 0x21a4000, no gpio pinctrl state.
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Heiko Schocher <hs@denx.de>
Maintainers need to be notified more directly of the need to convert these
drivers. Add a note to the top each affected file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
Now that driver model is used for I2C on all boards, we can split the
high-speed code into its own driver. There is virtually no common code,
and this significantly reduces confusion.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
CONFIG_SUNXI -> CONFIG_ARCH_SUNXI
and removed CONFIG_SUNIX from config_whitelist.txt
Cc: Simon Glass <sjg@chromium.org>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Change the error return value -ENODEV from to -EINVAL for more
reasonable.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Due to the peripheral clock driver improvement, remove the
unnecessary clock calling.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Make sure the driver writes the cmd_data register only once per
read transfer instead of doing so potentially repeatedly.
In case the read transfer didn't finish quickly enough, the loop
in the driver code would spin fast enough to write the same value
into the cmd_data register again before re-checking whether the
transfer completed, which would cause another spurious read transfer
on the bus.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
These have now landed upstream. The naming is different and in one case the
function signature has changed. Update the code to match.
This applies the following upstream commits by
Thierry Reding <treding@nvidia.com> :
604e61e fdt: Add functions to retrieve strings
8702bd1 fdt: Add a function to get the index of a string
2218387 fdt: Add a function to count strings
Signed-off-by: Simon Glass <sjg@chromium.org>
This gives a build warning on 64-bit x86. Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Boards where ECs that use a I2C port != 0 specify this in the
devicetree file via the google,remote-bus property.
Previously this was ignored and hardcoded to port 0.
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: u-boot@lists.denx.de
Acked-by: Simon Glass <sjg@chromium.org>
Now that the standard clock/reset APIs are available for all Tegra SoCs,
convert the I2C driver to use them exclusively, and remove any references
to the custom Tegra-specific APIs.
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
By adding the "marvell,mv78230-i2c" compatible property, we can enable
this I2C driver to support these new ARM64 chips as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Heiko Schocher <hs@denx.de>
The I2C bus will get stuck when reading 0 byte. So we add validation of
the read length in i2c_read(). This issue only occurs on read operation.
Signed-off-by: jinghua <jinghua@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Heiko Schocher <hs@denx.de>
This patch adds runtime speed configuration to the mv_i2c driver.
Currently standard (max 100kHz) and fast mode (max 400kHz) are
supported.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Heiko Schocher <hs@denx.de>
To prepare for the DM conversion, we add a layer of compatibility
functions to be used by both the legacy and the DM functions.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Heiko Schocher <hs@denx.de>
Now, arch/${ARCH}/include/asm/errno.h and include/linux/errno.h have
the same content. (both just wrap <asm-generic/errno.h>)
Replace all include directives for <asm/errno.h> with <linux/errno.h>.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Fixup include/clk.]
Signed-off-by: Tom Rini <trini@konsulko.com>
Since the 'clk_client.h' doesn't exist, it should be 'clk.h'.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The special handling of the chip address and register address must only
happen before we send the data buffer, otherwise we will end up
inserting both of these every 32 bytes.
Signed-off-by: John Keeping <john@metanate.com>
Acked-by: Simon Glass <sjg@chromium.org>
There is no point in writing intermediate values to the txdata
registers.
Also add padding to the debug logging to make it easier to read when
there are leading zeroes.
Signed-off-by: John Keeping <john@metanate.com>
Acked-by: Simon Glass <sjg@chromium.org>
Make it clear that we are using the same value in two adjacent lines.
Signed-off-by: John Keeping <john@metanate.com>
Acked-by: Simon Glass <sjg@chromium.org>
Patch f8a10ed1 [i2c: mvtwsi: Make address length variable] accidentally
inverted the sequence of address bytes sent to the I2C device. This
patch corrects this by sending the highest byte first and the lowest
byte last again.
Tested on theadorable Armada-XP board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Heiko Schocher <hs@denx.de>
The nvidia,bpmp property is left over from an old BPMP I2C binding, and
shouldn't be present. Remove it from the SoC DT file, and update the
I2C driver not to parse it; the value wasn't used for anything any more
anyway.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The Tegra I2C binding dictates that the clock name for the Tegra I2C clock
be "div-clk" not "i2c". Fix the Tegra186 DT and I2C driver to honor this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This patch adds support for the SMBus block read/write functionality.
Other protocols like the SMBus quick command need to get added
if this is needed.
This patch also removed the SMBus related defines from the Ivybridge
pch.h header. As they are integrated in this driver and should be
used from here. This change is added in this patch to avoid compile
breakage to keep the source git bisectable.
Tested on a congatec BayTrail board to configure the SMSC2513 USB
hub.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
clk/reset API was tested on T186 platform and previous chip like
T210/T124 will still use the old APIs.
Signed-off-by: Bryan Wu <pengw@nvidia.com>
(swarren, simplified some ifdefs, removed indent level inside an ifdef)
(swarren, added comment about the ifdefs)
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
On Tegra186, some I2C controllers are directly controlled by the main CPU,
whereas others are controlled by the BPMP, and can only be accessed by the
main CPU via IPC requests to the BPMP. This driver covers the latter case.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Some code may want to read reg values from DT, but from nodes that aren't
associated with DM devices, so using dev_get_addr_index() isn't
appropriate. In this case, fdtdec_get_addr_size_*() are the functions to
use. However, "translation" (via the chain of ranges properties in parent
nodes) may still be desirable. Add a function parameter to request that,
and implement it. Update all call sites to default to the original
behaviour.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Squashed in build fix from Stephen:
Signed-off-by: Simon Glass <sjg@chromium.org>
The i2c uclass has a default setting for per_child_platdata_auto_alloc_size
so drivers do not need to set it. Remove this from drivers to avoid
confusion.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
As I2C can be used before DRAM initialization for reading EEPROM,
avoid using static variables stored in BSS, since BSS is in DRAM, which
may not have been initialised yet. Explicitly mark "static global"
variables as belonging to the .data section.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Heiko Schocher<hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Quite a few places have a bind() method which just calls dm_scan_fdt_dev().
We may as well call dm_scan_fdt_dev() directly. Update the code to do this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Due to a oversight in testing, the initialization of the recently
introduced Freescale I2C DM driver works only for 36 bit mode of e.g.
the MPC85XX SoCs (specifically, if the physical addresses are 64 bit
wide and the DT addresses 32 bit wide).
This patch corrects the initialization so that it will work in a more
general setting.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: York Sun <york.sun@nxp.com>
Some devices using the MVTWSI driver have the option to run at speeds
faster than Standard Mode (100kHZ). On the Armada 38x controllers, this
is actually necessary, since due to erratum FE-8471889, a timing
violation concerning repeated starts prevents the controller from
working correctly in Standard Mode. One of the workarounds recommended
in the erratum is to set the bus to Fast Mode (400kHZ) operation and
ensure all connected devices are set to Fast Mode.
In the current version of the driver, however, the delay times are
hard-coded to 10ms, corresponding to Standard Mode operation. To take
full advantage of the faster modes, we would need to either keep the
currently configured I2C speed in a globally accessible variable, or
pass it to the necessary functions as a parameter. For DM, the first
option is not a problem, and we can simply keep the speed in the private
data of the driver. For the legacy interface, however, we would need to
introduce a static variable, which would cause problems with boots from
NOR flashes; see commit d6b7757 "i2c: mvtwsi: Eliminate
twsi_control_flags."
As to not clutter the interface with yet another parameter, we therefore
keep the default 10ms delays for the legacy functions.
In DM mode, we make the delay time dependant on the frequency to allow
taking full advantage of faster modes of operation (tested with up to
1MHZ frequency on Armada MV88F6820).
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Zero-length offsets are not properly handled by the driver. When a read
operation with a zero-length offset is started, a START condition is
asserted, and since no offset bytes are transferred, a repeated START is
issued immediately after, which confuses the controller.
To fix this, we send the first START only if any address bytes need to
be sent, and keep track of the expected start status accordingly.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
This patch adds the necessary functions and Kconfig entry to make the
MVTWSI I2C driver compatible with the driver model.
A possible device tree entry might look like this:
i2c@11100 {
compatible = "marvell,mv64xxx-i2c";
reg = <0x11000 0x20>;
clock-frequency = <100000>;
u-boot,i2c-slave-addr = <0x0>;
};
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
The length of the address parameter of the __twsi_i2c_read and
__twsi_i2c_write functions is fixed to four bytes.
As a final step in the preparation of the DM conversion, we make the
length of this parameter variable by turning it into an array of bytes,
and convert the 32 bit value that's passed to the legacy functions into
a four-byte-array on the fly.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
To be able to use the compatibility layer from the DM functions, we
factor the adap parameter out of all functions, and pass the actual
register base instead.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
To prepare for the DM conversion, we add a layer of compatibility
functions to be used by both the legacy and the DM functions.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Since some additional parameters will be added in the course of this
patch series (especially with the addition of DM support), we replace
the longer "unsigned int" declarations with "uint" declarations to keep
the parameter lists more readable.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
The twsi_stop function contains a parameter "status," which is used to
pass in the current exit status of the function calling twsi_stop, and
either return this status unchanged if it indicates an error, or return
twsi_stop's exit status if it does not indicate an error.
While not massively complicated, this adds another purpose to the
twsi_stop function, which should have the sole purpose of asserting a
STOP condition on the bus (and not manage the exit status of its
caller).
Therefore, we move the exit status management into the caller functions
by introducing a "stop_status" variable and returning either the status
before the twsi_stop call (kept in the "status" variable), or the status
from the twsi_stop call, depending on which indicates an error.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Due to breaking boots from NOR flashes, commit d6b7757 ("i2c: mvtwsi:
Eliminate twsi_control_flags") removed the static global
twsi_control_flags variable, which kept a set of default flags that were
always or'd to the control register when writing. It was replaced with a
flags parameter, which was passed around between the functions that
needed it.
Since the twsi_control_flags variable was used just for the purposes of
a) setting the MVTWSI_CONTROL_TWSIEN on every control register write,
and
b) setting the MVTWSI_CONTROL_ACK from twsi_i2c_read if needed,
anyway, the added overhead of another variable being passed around is no
longer justified, and we are better off implementing this flag setting
logic locally in the functions that actually write to the control
register.
Therefore, this patch sets MVTWSI_CONTROL_TWSIEN on every control
register write, replaces the twsi_i2c_read's flags parameter with a
ack_flag parameter, which tells the function whether to acknowledge the
read or not, and removes every other instance of the flags variable.
This has the added benefit that now every notion of "global default
flags" is gone, and it's much easier to see which control flags are
actually set at which point in time.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
This patch fixes only comments/documentation: Streamline capitalization
and improve grammar/punctuation.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Convert groups of logically connected preprocessor defines into proper
enums, one macro into an inline function, and add documentation
to/extend existing documentation of these items.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
This patch fixes seven style violations: Six superfluous spaces after
casts, and one logical continuation violation.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
parse dt parameter of i2c devices only when CONFIG_OF_CONTROL
is enabled.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This does not have much impact on behavior, but makes code look more
more like Linux. The use of devm_ioremap() often helps to delete
.remove callbacks entirely.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The following changes are made to the clock API:
* The concept of "clocks" and "peripheral clocks" are unified; each clock
provider now implements a single set of clocks. This provides a simpler
conceptual interface to clients, and better aligns with device tree
clock bindings.
* Clocks are now identified with a single "struct clk", rather than
requiring clients to store the clock provider device and clock identity
values separately. For simple clock consumers, this isolates clients
from internal details of the clock API.
* clk.h is split so it only contains the client/consumer API, whereas
clk-uclass.h contains the provider API. This aligns with the recently
added reset and mailbox APIs.
* clk_ops .of_xlate(), .request(), and .free() are added so providers
can customize these operations if needed. This also aligns with the
recently added reset and mailbox APIs.
* clk_disable() is added.
* All users of the current clock APIs are updated.
* Sandbox clock tests are updated to exercise clock lookup via DT, and
clock enable/disable.
* rkclk_get_clk() is removed and replaced with standard APIs.
Buildman shows no clock-related errors for any board for which buildman
can download a toolchain.
test/py passes for sandbox (which invokes the dm clk test amongst
others).
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add early i2c init function with conservative divider when the exact
clock rate is not available.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
In a system where the initial u-boot location is genuinely NOR flash (as
opposed to RAM or a cache-line setup by a pre-bootloader) writes to the
data section are problematic. At best these writes have no effect, at
worst they put the flash memory into a status mode which changes the
executable code underneath us.
Pass around a stack variable from the top of the twsi i2c driver to
avoid writing to global data.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
The DW I2C controller in the SPEAr SoCs doesn't support the enable
status register check. This patch selects
SYS_I2C_DW_ENABLE_STATUS_UNSUPPORTED for these boards.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
This patch adds an entry for the Designware I2C driver in Kconfig.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Some platforms don't implement the enable status register at offset 0x9c.
The SPEAr600 platform is one of them. The recently added check to this
status register can't be performend on these platforms.
This patch introduces a new config option that can be enabled on such
platforms not supporting this register.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Add support for common TI i2c mux which is available on ZynqMP zcu102
board.
DM i2c mux core code is selecting/deselecting bus before/after
every command is performed that's why only one channel is active at a
time. That's also the reason why deselect is just disable all available
channels.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
400kHz is maximum freq which can be used on Xilinx ZynqMP.
Support it with standard divider calculator.
Input freq is hardcoded to 100MHz input freq till we have clock driver
which can provide this information for exact configuration.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
set_bus_speed is the right function where bus speed should be setup.
This move enable option to remove probe and remove functions which are
empty.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Extract reading IP base address in function which is designed for it.
Also enable option to read more information from DT in this function.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
This patch adds support for the PCI(e) based I2C cores. Which can be
found for example on the Intel Bay Trail SoC. It has 7 I2C controllers
implemented as PCI devices.
This patch also adds the fixed values for the timing registers for
BayTrail which are taken from the Linux designware I2C driver.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This patch adds DM support to the designware I2C driver. It currently
supports DM and the legacy I2C support. The legacy support should be
removed, once all platforms using it have DM enabled.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
This patch prepares the designware I2C driver for the DM conversion.
This is mainly done by removing struct i2c_adapter from the functions
that shall be used by the DM driver version as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Integrating set_speed() into dw_i2c_set_bus_speed() will make the
conversion to DM easier for this driver.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
dw_i2c_enable() is used to dis-/en-able the I2C controller. It makes
sense to add such a function, as the controller is dis-/en-abled
multiple times in the code. Additionally, this function now checks,
if the controller is really dis-/en-abled. This code is copied
from the Linux I2C driver version.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add the ic_enable_status register to the i2c_regs struct. Additionally
the register offsets are added, to better check, if the offset matches
the register description in the datasheet.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
This is a possible drop in replacement for drivers/i2c/zynq-i2c.c
Since this is cadence IP it has been renamed to cdns-i2c,
to make sense with the compatible string.
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Currently, fdtdec_get_addr_size() does not support the address
translation, so it cannot handle device trees with non-straight
"ranges" properties. (This would be a problem with DTS for UniPhier
ARMv8 SoCs.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Implement i2c_idle_bus in driver, then setup_i2c can
be dropped for boards which enable DM_I2C/DM_GPIO/PINCTRL.
The i2c_idle_bus force bus idle flow follows setup_i2c in
arch/arm/imx-common/i2c-mxv7.c
This patch is an implementation following linux kernel patch:
"
commit 1c4b6c3bcf30d0804db0d0647d8ebeb862c6f7e5
Author: Gao Pan <b54642@freescale.com>
Date: Fri Oct 23 20:28:54 2015 +0800
i2c: imx: implement bus recovery
Implement bus recovery methods for i2c-imx so we can recover from
situations where SCL/SDA are stuck low.
Once i2c bus SCL/SDA are stuck low during transfer, config the i2c
pinctrl to gpio mode by calling pinctrl sleep set function, and then
use GPIO to emulate the i2c protocol to send nine dummy clock to recover
i2c device. After recovery, set i2c pinctrl to default group setting.
"
See Documentation/devicetree/bindings/i2c/i2c-imx.txt for detailed
description.
1. Introuduce scl_gpio/sda_gpio/bus in mxc_i2c_bus.
2. Discard the __weak attribute for i2c_idle_bus and implement it,
since we have pinctrl driver/driver model gpio driver. We can
use device tree, but not let board code to do this.
3. gpio state for mxc_i2c is not a must, but it is recommended. If
there is no gpio state, driver will give tips, but not fail.
4. The i2c controller was first probed, default pinctrl state will
be used, so when need to use gpio function, need to do
"pinctrl_select_state(dev, "gpio")" and after force bus idle,
need to switch back "pinctrl_select_state(dev, "default")".
This is example about how to use the gpio force bus
idle function:
"
&i2c1 {
clock-frequency = <100000>;
pinctrl-names = "default", "gpio";
pinctrl-0 = <&pinctrl_i2c1>;
pinctrl-1 = <&pinctrl_i2c1_gpio>;
scl-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>;
sda-gpios = <&gpio1 29 GPIO_ACTIVE_HIGH>;
status = "okay";
[....]
};
[.....]
pinctrl_i2c1_gpio: i2c1grp_gpio {
fsl,pins = <
MX6UL_PAD_UART4_TX_DATA__GPIO1_IO28 0x1b8b0
MX6UL_PAD_UART4_RX_DATA__GPIO1_IO29 0x1b8b0
>;
};
"
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: York Sun <york.sun@nxp.com>
"Fix mvtwsi not working on sun6i and newer sunxi SoCs" includes the following:
@@ -189,7 +200,8 @@ static int twsi_start(struct i2c_adapter *adap, int expected_status)
/* globally set TWSIEN in case it was not */
twsi_control_flags |= MVTWSI_CONTROL_TWSIEN;
/* assert START */
- writel(twsi_control_flags | MVTWSI_CONTROL_START, &twsi->control);
+ twsi_control_flags |= MVTWSI_CONTROL_START | MVTWSI_CONTROL_CLEAR_IFLG;
+ writel(twsi_control_flags, &twsi->control);
/* wait for controller to process START */
return twsi_wait(adap, expected_status);
}
The modification of twsi_control_flags done here was introduced while
merging to fix a line > 80 chars, but twsi_control_flags is a global variable
and should not be modified like this here, this commit fixes this, restoring
mvtwsi functionality.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Move the init code into the I2C driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This is used on most Intel platforms. We don't have a driver for it yet, but
add a stub to handle the init. For now this targets ivybridge so we may want
to add a device tree binding and generalise it when other platforms are
supported.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Since I2C muxes are seldom needed in SPL, and the code for this increases
the size somewhat, add a separate option to enable I2C muxes for SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
[hdegoede@redhat.com: Minor cleanups]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
applied with fixing 2 checkpatch warnings:
WARNING: please, no space before tabs
Signed-off-by: Heiko Schocher <hs@denx.de>
On sun6i and newer IFLG is a write-clear bit which is cleared by writing 1,
rather then a normal r/w bit which is cleared by writing 0.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
applied with fixing 3 checkpatch warnings
in drivers/i2c/mvtwsi.c:
WARNING: line over 80 characters
ERROR: code indent should use tabs where possible
WARNING: please, no spaces at the start of a line
Signed-off-by: Heiko Schocher <hs@denx.de>
In a number of places we had wordings of the GPL (or LGPL in a few
cases) license text that were split in such a way that it wasn't caught
previously. Convert all of these to the correct SPDX-License-Identifier
tag.
Signed-off-by: Tom Rini <trini@konsulko.com>
Until now, the SoC selection for the ARCH_MVEBU platforms has been done
in the config header. Using CONFIG_ARMADA_XP in a non-clear way. As
it needed to get selected for AXP and A38x based boards. This patch
now changes this to move the SoC selection to Kconfig. And also
uses CONFIG_ARCH_MVEBU as a common define for both AXP and A38x.
This makes things a bit clearer - especially for new board additions.
Additionally the defines CONFIG_SYS_MVEBU_DDR_AXP and
CONFIG_SYS_MVEBU_DDR_A38X are replaced with the already available
CONFIG_ARMADA_38X and CONFIG_ARMADA_XP.
And CONFIG_DDR3 is removed, as its not referenced anywhere.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This could avoid executing the code that only applies to i.MX platforms.
The bus_i2c_init() is called before relocation and will assgin value
to a static variable. If U-Boot is then still running in a flash
device, it's theoretically not allowed to write data to flash without
an erasing operation. For i.MX platforms, the U-Boot is always running
in DDR.
Actually it causes asynchronous error when the ARM64 system error
report is enabled and the flash write protect is set.
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
compiling U-Boot for avr32 boards shows since
commit 3d1957f0ea "dm: i2c: Add support for multiplexed I2C buses"
this warning:
Building current source for 4 boards (4 threads, 8 jobs per thread)
avr32: + atstk1002
+(atstk1002) drivers/i2c/built-in.o: warning: input is not relaxable
avr32: + grasshopper
+(grasshopper) drivers/i2c/built-in.o: warning: input is not relaxable
avr32: + atngw100
+(atngw100) drivers/i2c/built-in.o: warning: input is not relaxable
avr32: + atngw100mkii
+(atngw100mkii) drivers/i2c/built-in.o: warning: input is not relaxable
0 4 0 /4 0:00:16 : atngw100mkii
Fix it.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Roger Meier <r.meier@siemens.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
The console includes a global variable and several functions that are only
used by a small subset of U-Boot files. Before adding more functions, move
the definitions into their own header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Since busses are sorted in alphabetical order, introducing more
than nine busses led to unexpected behaviour.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Bus has to be held for repeated start regardless of
read/write access.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Acked-by: Heiko Schocher <hs@denx.de>
Reinhard Pfau complained that macros in ihs_i2c do not follow best practices.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Acked-by: Heiko Schocher <hs@denx.de>
There are two LS series processors are built on ARMv8 Layersacpe
architecture currently, LS2085A and LS1043A. They are based on
ARMv8 core although use different chassis, so create fsl-layerscape
to refactor the common code for the LS series processors which also
paves the way for adding LS1043A platform.
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Do not enable both I2C controllers by default. Enable them only when
they are selected.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
The driver assumed that I2C1 and I2C2 were always enabled,
and if they were not, then an asynchronous abort was (silently)
raised, to be caught much later on in the Linux kernel.
Fix this by making I2C1 and I2C2 optional just like I2C3 and I2C4
are.
To make the change binary-invariant, declare I2C1 and I2C2 in
every include/configs/ file which defines CONFIG_SYS_I2C_MXC.
Also, while updating README about CONFIG_SYS_I2C_MXC_I2C1 and
CONFIG_SYS_I2C_MXC_I2C2, add missing descriptions for I2C4 speed
(CONFIG_SYS_MXC_I2C4_SPEED) and slave (CONFIG_SYS_MXC_I2C4_SLAVE)
config options.
Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
This arch does not seem to be supported / used at all in the current
U-Boot mainline source tree any more. So lets remove the core u8500 code
and code that was only referenced by this platform.
Please note that this patch also removes these config options:
- CONFIG_PL011_SERIAL_RLCR
- CONFIG_PL011_SERIAL_FLUSH_ON_INIT
As they only seem to be referenced by u8500 based boards. Without any
such board in the current code, these config option don't make sense
any more. Lets remove them as well.
If someone still wants to use this platform, then please send patches
to re-enable support by adding at least one board that references this
code.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: John Rigby <john.rigby@linaro.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add an I2C driver for the Rockchip RK3288, using driver model. It should work
for other Rockchip SoCs also.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is a convenient way for a driver to get the hardware address of a
device, when regmap or syscon are not being used. Change existing callers
to use it as an example to others.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
We have flipped CONFIG_SPL_DISABLE_OF_CONTROL. We have cleansing
devices, $(SPL_) and CONFIG_IS_ENABLED(), so we are ready to clear
away the ugly logic in include/fdtdec.h:
#ifdef CONFIG_OF_CONTROL
# if defined(CONFIG_SPL_BUILD) && !defined(SPL_OF_CONTROL)
# define OF_CONTROL 0
# else
# define OF_CONTROL 1
# endif
#else
# define OF_CONTROL 0
#endif
Now CONFIG_IS_ENABLED(OF_CONTROL) is the substitute. It refers to
CONFIG_OF_CONTROL for U-boot proper and CONFIG_SPL_OF_CONTROL for
SPL.
Also, we no longer have to cancel CONFIG_OF_CONTROL in
include/config_uncmd_spl.h and scripts/Makefile.spl.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
LPC32xx has 3 I2C bus controllers, 2 of them are used as generic ones
and their parent clock is HCLK and CLK_HI/CLK_LO registers are 10 bit
wide. This means that if HCLK is 104MHz, then minimal configurable I2C
clock speed is about 51KHz.
Only USB OTG I2C bus controller CLK registers are 8 bit wide, thus in
assumption that peripheral clock is 13MHz it allows to set the minimal
bus speed about 25.5KHz.
Check for negative half clock value is removed since it is always false.
The change fixes the following problem for I2C busses 0 and 1:
=> i2c dev 0
Setting bus to 0
=> i2c speed 100000
Setting bus speed to 100000 Hz
Failure changing bus speed (-22)
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Tested-by: Sylvain Lemieux <slemieux@tycoint.com>
Updated the LPC32xx I2C driver to support
the OTG I2C that is part of the USB module.
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Acked-by: Marek Vasut <marex@denx.de>
Fix a condition that generate watchdog timeout inside "lpc32xx_i2c_write" when parameters alen = 0 and len = 0.
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Fix a condition that generate watchdog timeout inside "lpc32xx_i2c_read" when parameters alen != 0 and len = 0.
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
The HCLK is not constant and can take different value; use the api function to get the value of the HCLK for the I2C clock high and low computation.
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
The menuconfig for drivers are getting more and more cluttered
and unreadable because too many entries are displayed in a single
flat menu. Use hierarchic menu for each category.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Update to apply again in a few places, drop USB hunk]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add a driver to support the special LDO access used by spring. This is a
custom method in the cros_ec protocol - it does not use an I2C
pass-through.
There are two implementation choices:
1. Write a special LDO driver which can talk across the EC. Duplicate all
the logic from TPS65090 for retrying when the LDO fails to come up.
2. Write a special I2C bus driver which pretends to be a TPS65090 and
transfers reads and writes using the LDO message.
Either is distasteful. The latter method is chosen since it results in less
code duplication and a fairly simple (30-line) implementation of the core
logic.
The crosec 'ldo' subcommand could be removed (since i2c md/mw will work
instead) but is retained as a convenience.
Signed-off-by: Simon Glass <sjg@chromium.org>
The Chrome OS EC supports tunnelling through to an I2C bus on the EC. This
currently uses a copy of the I2C command code and a special 'crosec'
sub-command.
With driver model we can define an I2C bus which tunnels through to the EC,
and use the normal 'i2c' command to access it. This simplifies the code and
removes some duplication.
Add an I2C driver which tunnels through to the EC. Adjust the EC code to
support binding child devices so that it can be set up. Adjust the existing
I2C xfer function to fit driver model better.
For now the old code remains to allow things to still work. It will be
removed in a later patch once the new flow is fully enabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
The existing driver model implementation uses the old non-driver-model code
to operate, but has become impossibly tangled as a result. The actual
algorithm is quite simple.
Also the normal-speed and high-speed buses are quite different and it
doesn't seem that useful to put them in the same driver.
Finally, there is a bug which breaks communication with the Maxim sound
codec and may cause problems with other device.
Rewrite the driver model code for normal-speed operation so that it is
easier to understand, and fix the bug. Add a TODO to split the drivers.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
This function should not use mixed case, and it is simpler to use
clrbits_le32() when clearing bits. Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
While I2C supports multi-master buses this is difficult to get right.
The implementation on the master side in software is quite complex.
Clock-stretching and the arbitrary time that an I2C transaction can take
make it difficult to share the bus fairly in the face of high traffic.
When one or more masters can be reset independently part-way through a
transaction it is hard to know the state of the bus.
This driver provides a scheme based on two 'claim' GPIOs, one driven by the
AP (Application Processor, meaning the main CPU) and one driven by the EC
(Embedded Controller, a small CPU aimed at handling system tasks). With
these they can communicate and reliably share the bus. This scheme has
minimal overhead and involves very little code. It is used on snow to
permit the EC and the AP to share access to the main system PMIC and
battery. The scheme can survive reboots by either side without difficulty.
This scheme has been tested in the field with millions of devices.
Since U-Boot runs on the AP, the terminology used is 'our' claim GPIO,
meaning the AP's, and 'their' claim GPIO, meaning the EC's. This terminology
is used by the device tree bindings in Linux also.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a new I2C_MUX uclass. Devices in this class can multiplex between
several I2C buses, selecting them one at a time for use by the system.
The multiplexing mechanism is left to the driver to decide - it may be
controlled by GPIOs, for example.
The uclass supports only two methods: select() and deselect().
The current mux state is expected to be stored in the mux itself since
it is the only thing that knows how to make things work. The mux can
record the current state and then avoid switching unless it is necessary.
So select() can be skipped if the mux is already in the correct state.
Also deselect() can be made a nop if required.
Signed-off-by: Simon Glass <sjg@chromium.org>
Sometimes it is useful to be able to transfer a raw I2C message. This
happens when the chip address needs to be set manually, or when the data to
be sent/received is in another buffer.
Add a function to provide access to this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
Add a way to dump the contents of an I2C message for debugging purposes.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
When driver model is not used the current code does not correctly select
the pinmux for the I2C bus. This bug was introduced by this commit:
8dfcbaa dm: i2c: s3c24x0: adjust to dm-i2c api
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add support in mxc_i2c driver, iomux_v3 and vf610 architecture for the four
I2C instances available in VF610.
Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
Add the legacy i2c_reg_read/write() functions to the compatibility layer
so that they can be used when CONFIG_DM_I2C_COMPAT is defined.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
The business for UniPhier Soc family has been transferred from
Panasonic Corporation to Socionext Inc.
Update the SoC select menu in Kconfig.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
In the Linux coding style, it is recommended to include <linux/io.h>
rather than <asm/io.h>. Follow this trend.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Since i've been married, i also have a new surname.
Mr. Petermaier moved to Mr. Schmelzer.
In this patch i update all files in which my (old) name is present.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
The function get_emul() in sandbox i2c bus driver, always returns
first child as i2c emul device. This may only work for i2c devices
with a single child, which is an only i2c emul device.
In case when i2c device has more than one child (e.g. PMIC), and
one is i2c emul, then the function should search it by check uclass
id for each child. This patch add this change to the get_emul().
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Tested on sandbox:
Tested-by: Simon Glass <sjg@chromium.org>
1. Introduce a new structure `struct mxc_i2c_bus`, this structure will
used for non-DM and DM.
2. Remove `struct mxc_i2c_regs` structure, but use register offset to access
registers based on `base` entry of `struct mxc_i2c_bus`.
3. Remove most `#ifdef I2C_QUIRK_REG`. Using driver_data to contain platform
flags. A new flag is introduced, I2C_QUIRK_FLAG.
4. Most functions use `struct mxc_i2c_bus` as one of the parameters.
Make most functions common to DM and non-DM, try to avoid duplicated code.
5. Support DM, but pinctrl is not included. Pinmux setting is still set
by setup_i2c, but we do not need bus_i2c_init for DM.
6. struct i2c_parms and struct sram_data are removed.
7. Remove bus_i2c_read bus_i2c_write prototype in header file. The frist
paramter of bus_i2c_init is modified to i2c index. Add new prototype
i2c_idle_bus and force_bus_idle. Since bus_i2c_init is not good for
DM I2C and pinctrl is missed, we use a weak function for i2c_idle_bus.
Board file take the responsibility to implement this function, like this:
"
int i2c_idle_bus(struct mxc_i2c_bus *i2c_bus)
{
if (i2c_bus->index == 0)
force_bus_idle(i2c_pads_info0);
else if (i2c_bus->index == 1)
force_bus_idle(i2c_pads_info1);
else
xxxxxx
}
"
8. Introduce a weak function, enable_i2c_clk
9. Tested on an i.MX7 platform. Log info:
=> dm tree
Class Probed Name
----------------------------------------
root [ + ] root_driver
simple_bus [ ] |-- soc
simple_bus [ ] | |-- aips-bus@30000000
simple_bus [ ] | | |-- anatop@30360000
simple_bus [ ] | | `-- snvs@30370000
simple_bus [ ] | |-- aips-bus@30400000
simple_bus [ ] | `-- aips-bus@30800000
i2c [ ] | |-- i2c@30a20000
i2c [ ] | `-- i2c@30a40000
simple_bus [ ] `-- regulators
=> i2c dev 0
Setting bus to 0
=> i2c probe
Valid chip addresses: 08 50
=> i2c md 8 31
0031: 08 08 08 08 08 08 08 08 08 08 08 08 08 08 08 08
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Acked-by: Simon Glass <sjg@chromium.org>
We can currently set this but there is no API function to get it. Add one.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Heiko Schocher<hs@denx.de>
This is a matter of simple additional ifdefery to cater
for the different register layout of the S3C2440 chip.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
dm_gpio_set_dir_flags() will also set gpio output value when switching to
gpio output. So it's not necessary to call dm_gpio_set_value() after
dm_gpio_set_dir_flags() call.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Simon Glass <sjg@chromium.org>
At present this driver has a few test features. They are needed for running
the driver model unit tests but are confusing and unnecessary if using
sandbox at the command line. Add a flag to enable the test mode, and don't
enable it by default.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add driver model versions of the legacy functions to read and write a
single byte register. These are a useful shortcut in many cases.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
Some SoCs have more than two I2C busses. Instead of adding ifdef
to the driver, macros are put into board header file where
CONFIG_SYS_I2C_MXC is defined.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Heiko Schocher <hs@denx.de>
The existing get_get_of_data() function provides access to both the driver's
compatible string and its driver data. However only the latter is actually
useful. Update the interface to reflect this and fix up existing users.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
This commit adds driver model support to software emulated i2c bus driver.
This driver supports kernel-style device tree bindings. Fdt properties in use:
- compatible - "i2c-gpio"
- gpios - data and clock GPIO pin phandles
- delay-us - micro seconds delay between GPIOs toggle operations,
which is 1/4 of I2C speed clock period.
Added:
- Config: CONFIG_DM_I2C_GPIO
- File: drivers/i2c/i2c-gpio.c
- File: doc/device-tree-bindings/i2c/i2c-gpio.txt
Driver base code is taken from: drivers/i2c/soft-i2c.c, changes:
- use "i2c-gpio" naming
- update comments style
- move preprocesor macros into functions
- add device tree support
- add driver model i2c support
- code cleanup,
- add Kconfig entry
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Added braces in i2c_gpio_xfer() to fix style nit:
Signed-off-by: Simon Glass <sjg@chromium.org>
In the case where the arch defines a custom map_sysmem(), make sure that
including just mapmem.h is sufficient to have these functions as they
are when the arch does not override it.
Also split the non-arch specific functions out of common.h
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a convenience function to access the private data that a uclass stores
for each of its devices. Convert over most existing uses for consistency
and to provide an example for others.
Signed-off-by: Simon Glass <sjg@chromium.org>
Orion5x, Kirkwood and Armada XP platforms come with a single TWSI (I2C) MVTWSI
controller. However, other platforms using MVTWSI may come with more: this is
the case on Allwinner (sunxi) platforms, where up to 4 controllers can be found
on the same chip.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The current implementation for baudrate calculation is incorrect.
This part from the formula:
"2 ^ (n + 1)" is not equivalent to (1 << n) but to (2 << n)!
This patch fixes this and moves this calculation to a function instead of using a macro.
This new function is taken from the Linux kernel.
This was detected and tested on the Marvell Armada A38x DB-88F6820-GP eval board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Heiko Schocher <hs@denx.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Panasonic's System LSI products, UniPhier SoC family, have been
transferred to Socionext Inc.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Make this option available in Kconfig and clean up the board that uses it.
Note there is also an entry in exynos5-common.h but this affects multiple
boards and should be dropped as part of the Samsung I2C migration to
driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Expand the help messages for each driver. Add missing Kconfig for I2C,
SPI flash and thermal.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Make the driver model I2C API available always, even if driver model
is not enabled. This allows for a 'soft' switch-over, where drivers can
use the new structures in code which is compiled but not yet used. This
makes migration easier in some cases.
Fix up the existing drivers which define their own 'struct i2c_msg'.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
As with i2c_read() and i2c_write(), add a dm_ prefix to the driver model
versions of these functions to avoid conflicts.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
If no device is connected to I2C bus, the i2c probe command
can take a lot of time for probe each address. This commit
reduces the busy timeout to 10ms for standard and high speed
modes. This doesn't break the transmission an also allow for
properly probe the devices.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Changes v3:
- new commit, after split the next one
Tested-by: Simon Glass <sjg@chromium.org>
These functions are useful in case the board calls them. Also fix a missing
parameter caused by applying the wrong patch (actually I failed to send v2
and applied v1 by mistake).
Signed-off-by: Simon Glass <sjg@chromium.org>
Since U-Boot can support different offset lengths (0-4 bytes), add a device
tree property to specify this. This avoids hard-coding it in the driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
This commit adjusts the s3c24x0 driver to new i2c api
based on driver-model. The driver supports standard
and high-speed i2c as previous.
Tested on Trats2, Odroid U3, Arndale, Odroid XU3
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Tested-by: Simon Glass <sjg@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
This patch fixes build error for CONFIG_DM_I2C_COMPAT.
In i2c_get_chip_for_busnum() call, one of argument was missed,
which was offset_len. Now it is set to 'alen' as previous.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
At present we go through various contortions to store the I2C's chip
address in its private data. This only exists when the chip is active so
must be set up when it is probed. Until the device is probed we don't
actually record what address it will appear on.
However, now that we can support per-child platform data, we can use that
instead. This allows us to set up the address when the child is bound,
and avoid the messy contortions.
Unfortunately this is a fairly large change and it seems to be difficult to
break it down further.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
At present we try to use the 'reg' property and device tree aliases to give
devices a sequence number. The 'reg' property is often actually a memory
address, so the sequence numbers thus-obtained are not useful. It would be
better if the devices were just sequentially numbered in that case. In fact
neither I2C nor SPI use this feature, so drop it.
Some devices need us to look up an alias to number them within the uclass.
Add a flag to control this, so it is not done unless it is needed.
Adjust the tests to test this new behaviour.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Rather than assuming that the chip offset length is 1, allow it to be
provided. This allows chips that don't use the default offset length to
be used (at present they are only supported by the command line 'i2c'
command which sets the offset length explicitly).
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
For boards which use multiple I2C devices, or for SOCs which support
multiple boards, we might want to convert these to driver model at different
times. At present this is difficult because we need to either use
CONFIG_DM_I2C for a board or not.
Add a compatibility layer which implements the old API, thus allowing a
board to move to driver model for I2C without requiring that everything it
uses is moved in the same commit.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a dm_ prefix to driver model I2C functions so that we can keep the old
ones around.
This is a little unfortunate, but on reflection it is too difficult to
change the API. We can undo this rename when most boards and drivers are
converted to use driver model for I2C.
Signed-off-by: Simon Glass <sjg@chromium.org>
This commit adds on-chip I2C driver used on newer SoCs of Panasonic
UniPhier platform.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
This commit adds on-chip I2C driver used on some old Panasonic
UniPhier SoCs.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
We should not hardcode array size of i2c_data to 3. To CONFIG_FSL_LSCH3,
there are 4 i2c interface, but not 3. So the size of i2c_data array should
be calculated using "ARRAY_SIZE(i2c_bases)".
To avoid compile error, move i2c_bases before sram_data structure which
contains i2c_data array.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
This converts all Tegra boards over to use driver model for I2C. The driver
is adjusted to use driver model and the following obsolete CONFIGs are
removed:
- CONFIG_SYS_I2C_INIT_BOARD
- CONFIG_I2C_MULTI_BUS
- CONFIG_SYS_MAX_I2C_BUS
- CONFIG_SYS_I2C_SPEED
- CONFIG_SYS_I2C
This has been tested on:
- trimslice (no I2C)
- beaver
- Jetson-TK1
It has not been tested on Tegra 114 as I don't have that board.
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
This driver includes some test features such as only supporting certain
bus speeds. It passes its I2C traffic through to an emulator.
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
In order to test I2C we need some sort of emulation interface. Add hooks
to allow a driver to emulate an I2C device for sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
The uclass implements the same operations as the current I2C framework but
makes some changes to make it fit driver model better:
- Remove the chip address from API calls
- Remove the address length from API calls
- Remove concept of 'current' I2C bus
- Drop all existing init functions
Acked-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Due to an uninitialised variable, when muxes were deselected, any value
could be written to the mux control register. On the PCA9548, this could
result in multiple channels being selected, thus enabling multiple
pull-up resistors, and much bus capacitance.
The fix is simply to initialise the written value to zero.
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
U-Boot has never cared about the type when we get max/min of two
values, but Linux Kernel does. This commit gets min, max, min3, max3
macros synced with the kernel introducing type checks.
Many of references of those macros must be fixed to suppress warnings.
We have two options:
- Use min, max, min3, max3 only when the arguments have the same type
(or add casts to the arguments)
- Use min_t/max_t instead with the appropriate type for the first
argument
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Pavel Machek <pavel@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
[trini: Fixup arch/blackfin/lib/string.c]
Signed-off-by: Tom Rini <trini@ti.com>
In case of repeated START condition, the restart has to be kicked
before clear status (MSR register). If it is kicked after clear status,
R-Car I2C may transfer data (TXD register) or receive data (RXD register)
instead of transferring slave address (MAR register).
Signed-off-by: Ryo Kataoka <ryo.kataoka.wt@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Some slow I2C devices like Power Monitor(ZM7304) at times
do not work well with low timeout value, so I2C bus get stuck
during read cycle with this device, changing it to 100ms from
10ms works fine
A lot of other i2c drivers like mxc and i2c drivers of BOOTROM
also use relax timeouts to give sufficient ticks to work well
with slower devices
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
ppc4xx i2c master gets stuck on errors while repeated start is
active. Can be easily reproduced by "i2c md" on an unpopulated
i2c address. There is not stop condition given, scl remains
pulled low.
The only way out seems to be doing a stop manually and then a
soft reset.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Debugging some i2c trouble I saw on my scope that repeated
start is not working properply. The 4xx even held clock pulled down
after transfers. Having a look in the driver I realized
that IIC_CNTL_RPST is set on that part of the transfer that should
begin with a repeated start. But repeated start is about not sending a
stop condition, so IIC_CNTL_RPST has to be set on the last transfer
before the repeated start happens.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
In preparation for the SoCFPGA support of the designware I2C driver,
convert this driver to the common CONFIG_SYS_I2C framework.
This patch converts all users of this driver, this is:
- ST spearxxx boards
- AXS101 (ARC700 platform)
I couldn't test this patch on those boards. Only compile tested for all
spear boards. And tested on SoCFPGA.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Tested-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Vipin Kumar <vk.vipin@gmail.com>
Cc: Jeroen Hofstee <jeroen@myspectrum.nl>
This patch permeates the struct i2c_adapter throughout the driver,
so that it can be used to determine which adapter should be used.
Note that the driver still supports only one adapter. Note that
the patch does shuffle mxs_i2c_set_bus_speed() to the top of the
driver, but the function remains unchanged.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Heiko Schocher <hs@denx.de>
This patch just converts the function prototypes used throughout
this driver to match those of the i2c framework. There is so far
no functional change. This patch does not do the deeper integration
of the framework bits.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Heiko Schocher <hs@denx.de>
This patch prepares the MXS I2C driver for the conversion to the
new I2C driver framework by pulling out the hard-coded I2C0 address
from all the places.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Include the i2c header and change the non confirming
functions to do so.
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Acked-by: Heiko Schocher <hs@denx.de>
[trini: Fix i2c_get_bus_num prototype]
Signed-off-by: Tom Rini <trini@ti.com>
To support the Armada XP SoC, we just need to include the correct header.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
This move makes is possible to use this header not only from kirkwood
platforms but from all Marvell mvebu platforms.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
This would be useful to start moving various config options.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
The existing i.MX's I2C driver mxc_i2c.c is compatible
with the controller of LS102xA. As I2C's registers
are 8-bit on LS102xA, I2C_QUIRK_REG is enabled to
use 8-bit driver.
This patch is to add I2C 1,2,3 support for LS102xA.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Add support for the i2c controller found on all Allwinner sunxi SoCs,
this is the same controller as found on the Marvell orion5x and kirkwood
SoC families, with a slightly different register layout, so this patch uses
the existing mvtwsi code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-By: Prafulla Wadaskar <prafulla@marvell.com>
Acked-by: Heiko Schocher <hs@denx.de>
[ ijc -- updated u-boot-spl-fel.lds ]
Note this has only been tested on Allwinner sunxi devices (support for which
gets introduced by a later patch).
The kirkwood changes have been compile tested using the wireless_space board
config, the orion5x changes have been compile tested using the edminiv2 board
config.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heiko Schocher <hs@denx.de>
If a bus busy is detected when intializing the driver,
toggle 9 times the scl pin. Therefore enable the test mode
of the controller, in which the scl, sda pins can be
controlled manually.
Tested on the siemens boards pxm2, rut and dxr2.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Hannes Petermaier <oe5hpm@oevsv.at>
Cc: Lubomir Popov <lpopov@mm-sol.com>
Cc: Steve Sakoman <steve@sakoman.com>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Vincent Stehlé <v-stehle@ti.com>
Cc: Samuel Egli <samuel.egli@siemens.com>
IHS I2C master support was merely a hack in the osd driver.
Now it is a proper u-boot I2C framework driver, supporting the
v2.00 master features.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Freescale LayerScape with Chassis Generation 3 is a set of SoCs with
ARMv8 cores and 3rd generation of Chassis. We use different MMU setup
to support memory map and cache attribute for these SoCs. MMU and cache
are enabled very early to bootst performance, especially for early
development on emulators. After u-boot relocates to DDR, a new MMU
table with QBMan cache access is created in DDR. SMMU pagesize is set
in SMMU_sACR register. Both DDR3 and DDR4 are supported.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Varun Sethi <Varun.Sethi@freescale.com>
Signed-off-by: Arnab Basu <arnab.basu@freescale.com>
Since tegra_i2c_{read,write}'s debug() call dumps the chip address, dump
the address length (alen) too, so the address value can be correctly
interpreted.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Yen Lin <yelin@nvidia.com>
The Tegra I2C controller's TX FIFO contains 32-bit words. If the final
FIFO entry of a transaction contains fewer than 4 bytes, the driver
currently fills the unused FIFO bytes with uninitialized data. This can
be confusing when reading back the FIFO content for debugging purposes.
Solve this by explicitly initializing the variable containing FIFO data
before filling it (partially) with data. With this change,
send_recv_packets()'s loop's if (is_write) code mirrors the else (i.e.
read) branch.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Yen Lin <yelin@nvidia.com>
I2C read transactions are typically implemented as follows:
START(write) address REPEATED_START(read) data... STOP
However, Tegra's I2C driver currently implements reads as follows:
START(write) address STOP START(read) data... STOP
This sequence confuses at least the AS3722 PMIC on the Jetson TK1 board,
leading to corrupted read data in some cases. Fix the driver to chain
the transactions together using repeated starts to solve this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Yen Lin <yelin@nvidia.com>
These are used only once, so their is no need to have them global.
This also stops mvtwsi from using any bss vars making it easier to use
before dram init (to talk to the pmic to set the dram voltage).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The TWSI_FREQUENCY macro was wrong in 2 ways:
1) It was casting the result of the calculations to an u8, while i2c clk
rates are often >= 100Khz which won't fit in a u8, drop the cast.
2) It had an extra factor of 2 in the divider which neither the datasheet nor
the Linux driver have.
The comment for the default value was wrongly saying that m lives in
bits 4-7, while in reality it is in bits 3-6, as can be seen from the correct
shift by 3 used in i2c_init().
While at it remove the unused twsi_actual_speed variable.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Most of the I2C slaves support accesses in the typical style
that is : read/write series of bytes at particular address offset.
These transactions look like:"
(1) START:Address:Tx:Offset:RESTART:Address[0..4]:Tx/Rx:data[0..n]:STOP"
However there are certain devices which support accesses in
terms of the transactions as follows:
(2) "START:Address:Tx:Txdata[0..n1]:Clock_stretching:
RESTART:Address:Rx:data[0..n2]"
Here Txdata is typically a command and some associated data,
similarly Rxdata could be command status plus some data received
as a response to the command sent.
Type (1) transactions are currently supportd in the
i2c driver using i2c_read and i2c_write APIs. I2C EEPROMs,
RTC, etc fall in this category.
To handle type (2) along with type (1) transactions,
i2c_read() function has been modified.
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
This driver needs a data structure in SRAM before SDRAM is available.
This is not alway the case using .data section. Moving this data
structure to global_data guarantees it is writable.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Troy Kisky <troy.kisky@boundarydevices.com>
- add davinci driver to new multibus/multiadpater support
- adapted all config files, which uses this driver
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Heiko Schocher <hs@denx.de>
This patch moves the davinci i2c_defs.h file to drivers.i2c directory.
It will allow to reuse the davinci_i2c driver for TI Keystone2 SOCs.
Not used "git mv" command to move the file because small part of
it with definitions specific for Davinci SOCs has to remain in the
arch/arm/include/asm/arch-davinci.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Tom Rini <trini@ti.com>
Add support for the Kona I2C controller found on Broadcom mobile SoCs.
Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Reviewed-by: Steve Rae <srae@broadcom.com>
Reviewed-by: Tim Kryger <tkryger@linaro.org>
As soon as all boards have their CONFIG_SYS_I2C_BASE defined in
configuration files instead of "asm/arch/hardware.h" it's safe to remove
the inclusion in question and make driver platform-independent.
Cc: Tom Rini <trini@ti.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Vipin Kumar <vipin.kumar@st.com>
Cc: Armando Visconti <armando.visconti@st.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Adds support for set-speed on the OMAP24xx I2C Adapter.
Changes to omap24_i2c_write(...) for polling ARDY Bit from IRQ-Status.
Otherwise on a subsequent call the transfer of last byte from the
predecessor is aborted and therefore lost. For exmaple when
i2c_write(...) is followed by a i2c_setspeed(...) (which has to
deactivate and activate master for changing psc,...).
Minor cosmetical changes.
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
Cc: Heiko Schocher <hs@denx.de>
Make sure the I2C write queue is empty before leaving the mxs_i2c_write().
If we start and I2C write and only wait for ACK, the MXS I2C IP block may
enter next operation while still processing the write aftermath internally.
This will in turn disrupt one or more subsequent transfer(s).
A testcase for this issue is as such. This testcase is also interesting because
the first I2C_WRITE which becomes disruptive happens in the 'i2c read' command.
The 'i2c read' command first uses I2C_WRITE to send I2C address of the chip and
then uses I2C_READ to read data from the chip. After this command completes, the
'i2c probe' will use sequence of I2C_WRITE commands to probe the I2C bus. The
problem is that the first I2C_WRITE disrupted the I2C IP block operation and
this sideeffect propagates all the way to this next I2C_WRITE used by the 'i2c
probe' call. The result is the 'i2c probe' receives an ACK on I2C address 0x00,
even if this ACK was owned by the previous I2C_WRITE operation. Note that the
'i2c read' command must read from a valid I2C chip address.
Wrong:
> i2c probe
Valid chip addresses: 50 51
> i2c read 0x50 0x0.2 0x10 0x42000000
> i2c probe
Valid chip addresses: 00 50 51
With this patch
> i2c probe
Valid chip addresses: 50 51
> i2c read 0x50 0x0.2 0x10 0x42000000
> i2c probe
Valid chip addresses: 50 51
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Enhance the DesignWare I2C driver to support address length more
than 1 byte. This enhancement is required as some I2C slave
device such as EEPROM chip might have 16 bit address byte.
Signed-off-by: Chin Liang See <clsee@altera.com>
Acked-by: Alexey Brodkin <Alexey.Brodkin@synopsys.com>
Cc: Tom Rini <trini@ti.com>
cc: Armando Visconti <armando.visconti@st.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Heiko Schocher <hs@denx.de>
The ADI twi peripheral is not binding to Blackfin processor only.
Access i2c registers by standard io functions.
Fix coding style.
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Fixed bug with alen == 0 in 'i2c_write', 'i2c_read'
Further minor corrections:
- Write 'address' register before 'data' register.
- Write 'transfer_size' register before 'address' register.
Signed-off-by: Michael Burr <michael.burr@logicpd.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The architecture is unmaintained and dead, remove it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Michael Schwingen <michael@schwingen.org>
Cc: Tom Rini <trini@ti.com>
This fixes the following compiler warnings:
fti2c010.c: In function 'fti2c010_read':
fti2c010.c:204:8: warning: 'paddr' may be used uninitialized in this function [-Wuninitialized]
fti2c010.c: In function 'fti2c010_write':
fti2c010.c:266:8: warning: 'paddr' may be used uninitialized in this function [-Wuninitialized]
Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
Cc: Heiko Schocher <hs@denx.de>
Since we agreed on legacy implementation of "eeprom_{read|write}"
(http://patchwork.ozlabs.org/patch/295825/) I had to fix/make it work
again DesignWare I2C driver for cases when 1 EEPROM IC fake I2C with
anumber of "built-in" ICs with different chip addresses.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Tom Rini <trini@ti.com>
cc: Armando Visconti <armando.visconti@st.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Heiko Schocher <hs@denx.de>
Cc: Vipin KUMAR <vipin.kumar@st.com>
Cc: Tom Rix <Tom.Rix@windriver.com>
Cc: Mischa Jonker <mjonker@synopsys.com>
Cc: Kuo-Jung Su <dantesu@faraday-tech.com>
This corrects i2c core to interpret the value returned by
i2c_set_bus_speed as a success indicator rather than the
actual speed that was set. When i2c_set_bus_speed returns
a failure code, the speed is unknown so the adapter speed
is set to zero.
Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Reviewed-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-by: Steve Rae <srae@broadcom.com>
Acked-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Create the i2c adapter object for the fifth bus on SoC with more than
4 buses. This allow using all the bus available on T30.
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This patch adds the U_BOOT_I2C_ADAP_COMPLETE defines for channels
on Exynos5420 and Exynos5250 and also adds support for init function
for hsi2c channels
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Writing zero into I2Ci.I2C_CNT register causes random I2C failures in OMAP3
based devices. This seems to be related to the following advisory which
apears in multiple erratas for OMAP3 SoCs (OMAP35xx, DM37xx), as well as
OMAP4430 TRM:
Advisory:
I2C Module Does Not Allow 0-Byte Data Requests
Details:
When configured as the master, the I2C module does not allow 0-byte data
transfers. Note: Programming I2Ci.I2C_CNT[15:0]: DCOUNT = 0 will cause
undefined behavior.
Workaround(s):
No workaround. Do not use 0-byte data requests.
The writes in question are unnecessary from a functional point of view.
Most of them are done after I/O has finished, and the only one that preceds
I/O (in i2c_probe()) is also unnecessary because a stop bit is sent before
actual data transmission takes place.
Therefore, remove all writes that zero the cnt register.
Cc: Heiko Schocher <hs@denx.de>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Tom Rini <trini@ti.com>
Cc: Lubomir Popov <lpopov@mm-sol.com>
Cc: Enric Balletbo Serra <eballetbo@gmail.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Lubomir Popov <lpopov@mm-sol.com>
For a eeprom with a 2-bytes address (e.g., Ateml AT24C1024B),
the r/w address should be serial out in MSB order.
Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
Cc: Heiko Schocher <hs@denx.de>
Fix clock value initialisation for Exynos other than Exynos5 for hsi2c.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Heiko Schocher <hs@denx.de>
This patch adapts the s3c24x0 driver to the new i2c framework.
Config file is modified for all the boards that use the driver.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Minkyu Kang <mk7.kang@samsung.com>
CC: Heiko Schocher <hs@denx.de>
CC: Inderpal Singh <inderpal.singh@linaro.org>
CC: David Müller <d.mueller@elsoft.ch>
CC: Chander Kashyap <k.chander@samsung.com>
CC: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Reviewed-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Since the required API is gpio which is enclosed with CONFIG_ATMEL_LEGACY use
that switch here.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Acked-by: Heiko Schocher <hs@denx.de>
This delay applies to any data transfer on I2C bus.
For example 1kB data read with per-byte access (which happens if
environment is stored in I2C EEPROM) takes more than 10 seconds.
Moreover data bus driver has to care about bus state and data transfer,
but not about internal states of attached devices.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Tom Rini <trini@ti.com>
cc: Armando Visconti <armando.visconti@st.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Heiko Schocher <hs@denx.de>
Cc: Vipin KUMAR <vipin.kumar@st.com>
Cc: Tom Rix <Tom.Rix@windriver.com>
Cc: Mischa Jonker <mjonker@synopsys.com>
As it is stated in DesignWare I2C databook: writes to IC_TAR (0x4)
register succeed only when IC_ENABLE[0] is set to 0.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Tom Rini <trini@ti.com>
cc: Armando Visconti <armando.visconti@st.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Heiko Schocher <hs@denx.de>
Cc: Vipin KUMAR <vipin.kumar@st.com>
Cc: Tom Rix <Tom.Rix@windriver.com>
Cc: Mischa Jonker <mjonker@synopsys.com>
remove omap1510 i2c driver, as there is no board which uses it
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Jian Zhang <jzhang@ti.com>
- add zync i2c driver to new multibus/multiadpater support
- adapted all config files, which uses this driver
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Michal Simek <michal.simek@xilinx.com>
- add omap24xx driver to new multibus/multiadpater support
- adapted all config files, which uses this driver
Tested on the am335x based siemens boards rut, dxr2 and pxm2
posted here:
http://patchwork.ozlabs.org/patch/263211/
Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Tom Rini <trini@ti.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Steve Sakoman <sakoman@gmail.com>
Cc: Thomas Weber <weber@corscience.de>
Cc: Tom Rix <Tom.Rix@windriver.com>
Cc: Grazvydas Ignotas <notasas@gmail.com>
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Cc: Luca Ceresoli <luca.ceresoli@comelit.it>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Ilya Yanok <yanok@emcraft.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Nishanth Menon <nm@ti.com>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: Peter Barada <peter.barada@logicpd.com>
Cc: Nagendra T S <nagendra@mistralsolutions.com>
Cc: Michael Jones <michael.jones@matrix-vision.de>
Cc: Raphael Assenat <raph@8d.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Stefano Babic <sbabic@denx.de>
The endless waiting for a bit to be set can cause a hang, add a timeout
so we prevent such situation. A testcase for such a hang is below. The
testcase assumes a device to be present at address 0x50 and a device to
NOT be present at address 0x42 . Also note that the "sleep 1" induced
delays are imperative for this bug to manifest .
i2c read 0x42 0x0.2 0x10 0x42000000 ; sleep 1 ; \
i2c read 0x50 0x0.2 0x10 0x42000000 ; sleep 1 ; \
i2c read 0x42 0x0.2 0x10 0x42000000
The expected result of the above command is:
Error reading the chip.
Error reading the chip.
While without this patch, we observe a hang in the last read from 0x42
precisely when waiting for this bit to be set.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
This updates to new I2C framwwork on sh_i2c.
And this also updates boards(kzm9g and ecovec) that using sh_i2c.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The prototype of handlers had changed.
This commit uses cast with (void *) rather than
the handler-specific prototype.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Add support for hsi2c controller available on exynos5420.
Note: driver currently supports only fast speed mode 100kbps
Change-Id: I02555b1dc8f4ac21c50aa5158179768563c92f43
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Signed-off-by: R. Chandrasekar <rc.sekar@samsung.com>
At present the i2c ports are enumerated in a strange way - the
fdtdec_find_aliases_for_id() function is used, but then the ID returned
is ignored and the ports are renumbered. The effect is the same provided
that the device tree has the ports in the same order, or uses aliases,
and has no gaps, but it is not correct.
Adjust the code to use the function as intended. This will allows device
tree aliases to change the device order if required.
As a result, the i2c_busses variable is dropped. We can't be sure that
there are no 'holes' in the list of buses, so must check the whole
array.
Note: it seems that non-FDT operation is now broken in this drive and
will need to be reinstated for upstream.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/59369
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
The Exynos5 i2c driver does not handle NACKs properly. This change:
- fixes the NACK processing problem (do not continue transaction if
address cycle was NACKed)
- eliminates a fair amount of duplicate code
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-by: Simon Glass <sjg@google.com>
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
NoMMU systems have a access violation problem with i2c_reloc_fixup.
Blame for it is a double relocation of the adapter itself. The
i2c_adap_p is already relocated, if i2c_reloc_fixup is called.
This patch removes the relocation of i2c_adap_p from i2c_reloc_fixup
to fix this.
Signed-off-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
If user uses the I2C in before the relocation, board of sh and rmobile
will not start. This will solve this problem.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
check first, if we are on the bus, we want to enable. If so,
return immediately, do not calc max adapter number, nor check
other things.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
(Interface is not quite the same as Phillips PCA9547.)
Signed-off-by: Michael Burr <michael.burr@logicpd.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Michal Simek <monstr@monstr.eu>
Since commit 5dc5f36 removed B2 board support,
there are no boards enabling s3c44b0_i2c.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Andrea Scian <andrea.scian@dave-tech.it>
Acked-by: Heiko Schocher <hs@denx.de>
This workaround is for the erratum I2C A004447. Device reference
manual provides a scheme that allows the I2C master controller
to generate nine SCL pulses, which enable an I2C slave device
that held SDA low to release SDA. However, due to this erratum,
this scheme no longer works. In addition, when I2C is used as
a source of the PBL, the state machine is not able to recover.
At the same time, delete the reduplicative definition of SVR_VER
and SVR_REV. The SVR_REV is the low 8 bits rather than the low 16
bits of svr. And we use the CONFIG_SYS_FSL_A004447_SVR_REV macro
instead of hard-code value 0x10, 0x11 and 0x20.
The CONFIG_SYS_FSL_A004447_SVR_REV = 0x00 represents that one
version of platform has this I2C errata. So enable this errata
by IS_SVR_REV(svr, maj, min) function.
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Heiko Schocher <hs@denx.de>
When the code detected that the bus is hung (e.g. SDA stuck low),
send 9 pulses on SCL to try to fixup the bus.
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Heiko Schocher <hs@denx.de>
Tegra recently moved to the new I2C framework, which sets up I2C prior to
relocation, and prior to calling i2c_init_board(). This causes a crash on
Tegra boards.
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
In case only the CONFIG_SYS_I2C_SPEED is set in configuration file,
the CONFIG_SYS_I2C_SOFT_SPEED is defined as CONFIG_SYS_I2C_SPEED.
The CONFIG_SYS_I2C_SOFT_SPEED is then used throughout the driver.
Unfortunatelly, due to a typo in the driver, instead of defining
CONFIG_SYS_I2C_SOFT_SPEED, an CONFIG_SYS_SOFT_I2C_SPEED was defined
and therefore the driver failed to compile. The same applies for
CONFIG_SYS_I2C_SOFT_SLAVE , where the swap happens as well.
This patch fixes the issue.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
The sandburst-specific i2c drivers have been deleted, conflict was just
over the SPDX conversion.
Conflicts:
board/sandburst/common/ppc440gx_i2c.c
board/sandburst/common/ppc440gx_i2c.h
Signed-off-by: Tom Rini <trini@ti.com>
Faraday FTI2C010 is a multi-function I2C controller
which supports both master and slave mode.
This patch simplily implements the master mode only.
Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
CC: Heiko Schocher <hs@denx.de>
This patch adds support for Vybrid VF610 platform.
There are some differences between i.MX6 and Vybrid for I2C controller.
(1) The registers' offset are different.
(2) The I2C clock divider values are different.
(3) In I2C control register, the enable/disable/reset bit is inverted for Vybrid comparing to i.MX6.
(4) In I2C status register, the interrupt flag bit is cleared by writing "1" for Vybrid.
For i.MX6, this bit is cleared by writing "0".
(5) In I2C status register, the arbitration lost flag bit is cleared by writing "1" for Vybrid.
For i.MX6, this bit is cleared by writing "0".
Signed-off-by: Alison Wang <b18965@freescale.com>
This enables CONFIG_SYS_I2C on Tegra, updating existing boards and the Tegra
i2c driver to support this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Heiko Schocher <hs@denx.de>
Rather than using a variable in various places, add a single function,
tegra_i2c_get_bus(), which returns a pointer to information about a
bus.
This will make it easier to move to the new i2c framework.
Signed-off-by: Simon Glass <sjg@chromium.org>
- added to fsl_i2c driver new multibus/multiadpater support
- adapted all config files, which uses this driver
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
- added to soft_i2c driver new multibus/multiadpater support
- adapted all config files, which uses this driver
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
This Patch introduce the new i2c_core file, which holds
the I2C core functions, for the rework of the multibus/
multiadapter support.
Also adds changes in i2c.h for the new I2C multibus/multiadapter
support. This new support can be activated with the
CONFIG_SYS_I2C define.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
if alen is 0: no longer start a write cycle before reading data.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Reinhard Pfau <reinhard.pfau@gdsys.cc>
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Andy Fleming <afleming@freescale.com>
This patch resolves the below mentioned compilation error of i2c driver
for non-FDT case
Compilation error:
s3c24x0_i2c.c: In function 'board_i2c_init':
s3c24x0_i2c.c:544:18: error: 'CONFIG_MAX_I2C_NUM' undeclared (first use
in this function) s3c24x0_i2c.c:544:18: note: each undeclared
identifier is reported only once for each function it appears in
s3c24x0_i2c.c:545:3: warning: implicit declaration of function
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Amar <amarendra.xt@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch updates the function board_i2c_init() to add support for both
FDT and non-FDT for I2C, and initialise the I2C channels.
Signed-off-by: Amar <amarendra.xt@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
New i2c_read, i2c_write and i2c_probe functions, tested on OMAP4
(4430/60/70), OMAP5 (5430) and AM335X (3359); should work on older
OMAPs and derivatives as well. The only anticipated exception would
be the OMAP2420, which shall require driver modification.
- Rewritten i2c_read to operate correctly with all types of chips
(old function could not read consistent data from some I2C slaves).
- Optimised i2c_write.
- New i2c_probe, performs write access vs read. The old probe could
hang the system under certain conditions (e.g. unconfigured pads).
- The read/write/probe functions try to identify unconfigured bus.
- Status functions now read irqstatus_raw as per TRM guidelines
(except for OMAP243X and OMAP34XX).
- Driver now supports up to I2C5 (OMAP5).
Signed-off-by: Lubomir Popov <lpopov@mm-sol.com>
Tested-by: Heiko Schocher <hs@denx.de>
Albert's rework of the linker scripts conflicted with Simon's making
everyone use __bss_end. We also had a minor conflict over
README.scrapyard being added to in mainline and enhanced in
u-boot-arm/master with proper formatting.
Conflicts:
arch/arm/cpu/ixp/u-boot.lds
arch/arm/cpu/u-boot.lds
arch/arm/lib/Makefile
board/actux1/u-boot.lds
board/actux2/u-boot.lds
board/actux3/u-boot.lds
board/dvlhost/u-boot.lds
board/freescale/mx31ads/u-boot.lds
doc/README.scrapyard
include/configs/tegra-common.h
Build tested for all of ARM and run-time tested on am335x_evm.
Signed-off-by: Tom Rini <trini@ti.com>
T114 has a slightly different I2C clock, with a new (extra) divisor
in standard/fast mode and HS mode. Tested on my Dalmore, and the I2C
clock is 100KHz +/- 3Hz on my Saleae Logic analyzer.
Added a new entry in compat_names for T114 I2C since it differs
from the previous Tegra SoCs. A flag is set when T114 I2C HW is
found so new features like the extra clock divisor can be used.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
This patch corrects the following issues
1) Write the correct M/T Stop value to I2CSTAT after i2c write.
According to the spec, after finish the data transmission, we should
write a M/T Stop (I2C_MODE_MT | I2C_TXRX_ENA) to I2CSTAT instead of
a M/R Stop (I2C_MODE_MR | I2C_TXRX_ENA).
2) Not split the write to I2CSTAT into 2 steps in i2c read.
According to the spec, we should write the combined M/R Start value to
I2CSTAT after setting the slave address to I2CDS
3) Fix the mistake of making an equality check to an assignment.
In the case of I2C write with the zero-length address, while tranfering the
data, it should be an equality check (==) instead of an assignment (=).
Signed-off-by: Tom Wai-Hong Tam <waihong@chromium.org>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
This revomes the code under #if 0 in the s3c24x0_i2c driver.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Move these fields into arch_global_data and tidy up. This is needed for
both ppc and m68k since they share the i2c driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
The local functions in the mxs i2c driver are not marked static, make it so.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Heiko Schocher <hs@denx.de>
This patch resolves the following build errors for I2C driver in
VCMA9:
In file included from s3c24x0_i2c.c:40:0:
s3c24x0_i2c.h:38:17: error: field 'id' has incomplete type
s3c24x0_i2c.c:70:39: error: 'CONFIG_MAX_I2C_NUM' undeclared here (not
in a function) s3c24x0_i2c.c:70:31: warning: 'i2c_bus' defined but
not used [-Wunused-variable] s3c24x0_i2c.c:72:12: warning:
'i2c_busses' defined but not used [-Wunused-variable]
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Functions added to get the I2C bus number and reset I2C bus using
FDT node.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
There are three couple (hcnt/lcnt) of registers for each
speed (SS/FS/HS). The driver needs to set the proper couple
of regs according to what speed we are setting.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
In the newer versions of designware i2c IP there is the possibility
of configuring it with IC_EMPTYFIFO_HOLD_MASTER_EN=1, which basically
requires the s/w to generate the stop bit condition directly, as
the h/w will not automatically generate it when TX_FIFO is empty.
To avoid generation of an extra 0x0 byte sent as data, the
IC_STOP command must be sent along with the last IC_CMD.
This patch always writes bit[9] of ic_data_cmd even in the
older versions, assuming that it is a noop there.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
This patch modifies the S3C i2c driver to support both Exynos4 and Exynos5
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Minkyu Kang <mk7.kang@samsung.com>
OMAP5 has 8b i2c data register field, like OMAP2, 3 and 4. Handle in the same
way. This fixes the following error on OMAP5:
OMAP5430 EVM # mmc rescan
timed out in wait_for_bb: I2C_STAT=1410
twl6035: could not turn on LDO9.
Signed-off-by: Vincent Stehlé <v-stehle@ti.com>
This algorithm computes the values of TIMING{0,1,2} registers for the
MX28 I2C block. This algorithm was derived by using a scope, but the
result seems correct.
The resulting values programmed into the registers do not correlate
with the contents in datasheet. When using the values from the datasheet,
the I2C clock were completely wrong.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Wolfgang Denk <wd@denx.de>
The I2C block reset configures the I2C bus speed to strange value.
Read the I2C speed from the block before reseting the block and
restore it afterwards, so the I2C operates correctly. This issue
can be replicated by doing unsuccessful I2C transfer, after such
transfer finishes, the I2C block clock speed is misconfigured.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
According to FSL, the value in the TIMING2 register shall be 0x00300030
instead of what's written in the datasheet. This new value correlates
with older STMP36xx datasheet. Issues were detected in Linux when this
register was misconfigured, so write this correct value.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Use i2c_set_bus_speed() in i2c_init() within the mxs i2c driver
to avoid duplication of code.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
This patch implements the setup and retrieval functions for the I2C
bus speed on the MXS I2C IP.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
This patch pulls out the I2C speed setup from the i2c_init() call
and implements the bus configuration lookup table with register
values that needs to be programmed into the I2C IP to run at
particular speed.
This patch is a first step towards implementing run-time I2C bus
speed configuration for the MXS I2C IP.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Some functions in the MXC i2c driver were not static, fix this by
making them so.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
We add a return code to wait_for_bb() to be able to report errors to the
callers properly. We in turn handle this new error code in i2c_read, i2c_write
and i2c_probe.
Signed-off-by: Vincent Stehlé <v-stehle@ti.com>
fsl_i2c.c:217:14: warning: symbol 'get_i2c_clock' was not declared. Should it be static?
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Heiko Schocher <hs@denx.de>
Before this patch, i2c_{read,write} always returned 0.
Check TACK in i2c_raw_{read,write} so that i2c_{read,write} return non-zero when error.
Acked-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
Before this patch i2c_probe() always returned 0 and "i2c probe" command did not work properly.
Modify i2c_set_addr() to check TACK when waiting DTE and make i2c_probe() call this function.
Acked-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
sh_i2c.c support I2C0 and I2C1. This patch extends it to I2C4.
Acked-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
Adjust i2c_raw_read() in sh_i2c.c to work for SH73A0.
After this patch, "i2c md" and "i2c mw" command on U-Boot work properly on KZM-A9-GT board.
Acked-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
Correct BUSY bit define in ICSR from (1<<3) to (1<<4).
Acked-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
R-mobile SoC (at least SH73A0) has extension bits to store 8th bit of iccl and icch.
This patch add support for the extentin bits.
Acked-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
i2c didn't work on imx25 due to missing MXC_IPG_PERCLK. Now using
MXC_I2C_CLK on all imx systems using i2c.
Signed-off-by: Matthias Weisser <weisserm@arcor.de>
Acked-by: Stefano Babic <sbabic@denx.de>
The move is pretty straight-forward. ap20.h and tegra20.h were renamed to ap.h and tegra.h.
Some files remain in arch-tegra20 but 'include' a file in 'arch-tegra' with #defines & structs
that will be common between T20 and T30 HW. HW-specific #defines, etc. stay in the 'arch-tegra20'
'root' file.
All boards build OK w/MAKEALL -s tegra20. Checkpatch.pl runs clean. Seaboard works OK.
Signed-off-by: Tom Warren <twarren@nvidia.com>
irq_wait function is not referred to from anywhere.
Reported-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Convert TEGRA20_ defines to either TEGRA_ or NV_PA_ where appropriate.
Convert tegra20_ source file and function names to tegra_, also.
Upcoming Tegra30 port will use common code/defines/names where possible.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
The sys_proto.h functions (except the boot modes) are compatible with
i.MX233 and i.MX28 so we use 'mxs' prefix for its methods.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
This is make naming consistent with the kernel and devicetree and in
preparation of pulling out the common tegra20 code.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Various devices like EEPROMs require 2-byte address support to
be properly accessed. This patch adds this support for OMAP2/3/4
I2C controller driver.
I've tested it with EEPROM (16 bit address) and TPS65217 chip
(8 bit address) on TI Beaglebone board.
Unfortunately I don't have access to any compatible hardware
with 16bit data register so I can't test if those #ifdef
clauses really work.
CC: Tom Rini <trini@ti.com>
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
This adds multiple i2c channel support for I2C.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
This patch modifies the S3C I2C driver to suppport EXYNOS5.
The cahnges made to driver are as follows:
- I2C base address is passed as a parameter to many
functions to avoid multiple #ifdef
- Channel initialisation is moved to a commom funation
as it is required by i2c_init.
- Hardcoding for I2CCON_ACKGEN removed.
- Replaced printf with debug.
- Checkpatch issues resolved.
- Pinmux setting will be done in board/samsung/smdk5250/smdk5250.c
to avoid repeated setting of gpio lines, as it have multi bus support.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
struct s3c24x0_i2c is being moved to common local header file so that
the same can be used by s3c series and exynos series SoCs.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add support for calling a function that will toggle the
SCL line to return the bus to idle condition.
The actual toggling function is added in a later patch.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
This helps in a multiple bus master environment which
is why I also added a wait for bus idle.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
imx_reset is only referenced once so
move to that location.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Marek Vasut <marex@denx.de>
imx_start is only referenced once so
move to that location.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Marek Vasut <marex@denx.de>
wait_for_sr_state returns i2sr on success
so no need to read again.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Marek Vasut <marex@denx.de>
Not using udelay gives a more accurate timeout. The current implementation of udelay
in imx-common does not seem to wait at all for a udelay(1).
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Marek Vasut <marex@denx.de>
----
V2: Added WATCHDOG_RESET as suggested by Marek Vasut
add error message when stop fails
mxc_i2c: code i2c_probe as a 0 length i2c_write
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Initial code of i2c_read and i2c_write
is identical, move to subroutine.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Let's clear the sr register before waiting for
bit to be set, instead of clearing it after
hardware sets it. No real operational difference here,
but allows combining of i2c_imx_trx_complete and
i2c_imx_bus_busy in later patches.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Marek Vasut <marex@denx.de>
Use tx_byte function instead of having 3 copies
of the code.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Marek Vasut <marex@denx.de>
This is always selected when CONFIG_I2C_MXC is
selected, so it adds no value.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Marek Vasut <marex@denx.de>
Instead of clearing 2 bits, all the other
bits were set because '|=' was used instead
of '&='.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Large EEPROMs, e.g. 24lc32, need 2 byte to address the internal memory.
These devices require that the high byte of the internal address has to be
written first.
The mxs_i2c driver currently writes the address' low byte first.
The following patch fixes the byte order of the internal address that should
be written to the I2C device.
Signed-off-by: Torsten Fleischer <to-fleischer@t-online.de>
CC: Marek Vasut <marex@denx.de>
CC: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Other then being very weird, this code was also wrong.
For example, say I set speed to 100K. I'll read back the speed
as 85937. But the speed is really 85937.5, so we I reset
the speed to 85937, I'll get 73660.7. After a couple of transactions
my speed is now exactly 68750 so it will remain there.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
The following platforms had their config files changed
flea3, imx31_phycore, mx35pdk, mx53ard, mx53evk, mx53smd
and mx53loco.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Stefano Babic <sbabic@denx.de>
i2c_probe() is changed to reinit the i2c bus upon read failure.
This is naturally the case upon i2c bus probing.
Also, some printf messages upon read failure are removed. As they
would interfere with the "i2c probe" command.
Additionally, i2c_set_bus_speed() now returns 0, so that the
"i2c speed" command can be used.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Amit Virdi <amit.virdi@st.com>
Cc: Vipin Kumar <vipin.kumar@st.com>
The same places that check for CONFIG_OMAP44XX need to check for
CONFIG_AM33XX as we share the same i2c block.
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Heiko Schocher <hs@denx.de>
This reverts commit 0e57968a21.
The short version of the original commit is that some i2c devices cannot
be probed via read as they NAK the first cycle, so try and probe via a
write that we abort before it writes to the device. This however is not
allowed by the TRM for any of these parts. The section on I2C_CON
(table 17-35 I2C_CON for am/dm37x for example) says you must not change
the register while STT has been set. On these parts, the unpredictable
behavior that the chip exhibits is not problematic. On OMAP4 however it
results in the chip being in a bad state:
Panda # i2c probe
Valid chip addresses: 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12
13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 20 21 22 23 24 25 26 27 28 29 2A
2B 2C 2D 2E 2F 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F 40 41 42
43 44 45 46 47 48 49 4A 4B 4C 4D 4E 4F 50 51 52 53 54 55 56 57 58 59 5A
5B 5C 5D 5E 5F 60 61 62 63 64 65 66 67 68 69 6A 6B 6C 6D 6E 6F 70 71 72
73 74 75 76 77 78 79 7A 7B 7C 7D 7E 7F
Panda # i2c md 50 0
timed out in wait_for_pin: I2C_STAT=0
I2C read: I/O error
Error reading the chip.
We must revert the original behavior to bring probe back into line with
the TRM.
Cc: Nick Thompson <nick.thompson@ge.com>
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Heiko Schocher <hs@denx.de>
Add tegra_i2c_get_dvc_bus_num() to obtain the I2C bus number of DVC bus.
This allows us to talk to the PMU.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The designware i2c controller must be turned off before
setting the speed in IC_CON register, as stated in the
section 6.3.1 of the dw_apb_i2c_db.pdf.
Signed-off-by: Michel Sanches <michel.sanches@st.com>
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Earlier, a driver exists in the u-boot source for designware i2c interface. That
driver was specific to spear platforms. This patch implements the i2c controller
as a generic driver which can be used by multiple platforms
The driver files are now renamed to designware_i2c.c and designware_i2c.h and
these are moved into drivers/i2c folder for reusability by other
platforms
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Renesas SH7734 has two I2C interfaceis.
This supports these I2C.
V5: - include i2c.h.
- Add check of icsr bit polling logic.
- Implement i2c_probe.
V4: - Remove sh_i2c_dump_reg function.
- Use puts() when there's no format.
- Chnage check for I2C bus number.
- Remove space before the semi-colon.
V3: - Fix error for whitespace.
V2: - Changed bit control to use the clr|set|clrsetbits_* functions.
- Fix wrong comment style.
- Add new line before for loop in i2c_read.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Add basic i2c driver for Tegra2 with 8- and 16-bit address support.
The driver requires CONFIG_OF_CONTROL to obtain its configuration
from the device tree.
(Simon Glass: sjg@chromium.org modified for upstream)
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This reverts commits 2faa76196a as
this has introduced some large problems on all other platforms and have
more changes in them than the commit message implies.
Cc: Heiko Schocher <hs@denx.de>
Cc: Patil, Rachna <rachna@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
This reverts commit 498cbdfe62 as we need
to revert the i2c changes that add the support for the platform.
Cc: Heiko Schocher <hs@denx.de>
Cc: Patil, Rachna <rachna@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Existing OMAP I2C driver does not support address
length greater than one. Hence this patch is to
add support for 2 byte address read/write.
Signed-off-by: Philip, Avinash <avinashphilip@ti.com>
Signed-off-by: Hebbar, Gururaja <gururaja.hebbar@ti.com>
Signed-off-by: Patil, Rachna <rachna@ti.com>
At old overo boards TWL4030 RTC irq is connected to gpio112. Unfortunately
this pin is also used for revision detection. Therefore we need to send
shut-up to TWL4030 to avoid reading wrong revision. In SPL this must
be done before SDRAM is set up because the type of SDRAM is revision dependent.
By this patch it is ensured that all variables used by omap24xx_i2c.c are
located in SRAM.
Signed-off-by: Andreas Müller <schnitzeltony@gmx.de>
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Fix:
davinci_i2c.c: In function 'flush_rx':
davinci_i2c.c:81:6: warning: variable 'dummy' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
This supports I2C of Renesas SH.
I tested on SH7724.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
CC: Heiko Schocher <hs@denx.de>
* 'master' of git://git.denx.de/u-boot-arm:
arm, davinci: add DAVINCI_MMC_CLKID
arm, davinci_emac: fix driver bug if more then 3 PHYs are detected
arm, davinci: da850/dm365 lowlevel cleanup
omap5: Add omap5_evm board build support.
omap4/5: Add support for booting with CH.
omap5: emif: Add emif/ddr configurations required for omap5 evm
omap5: clocks: Add clocks support for omap5 platform.
omap5: Add minimal support for omap5430.
omap: Checkpatch fixes
omap4: make omap4 code common for future reuse
GCC4.6: Squash warnings in onenand_base.c
GCC4.6: Fix common/usb.c on xscale
OneNAND: Add simple OneNAND SPL
PXA: vpac270: Enable the new generic MMC driver
PXA: Cleanup serial_pxa
PXA: Drop csb226 and innokom boards (unmaintained)
m28evk: Fix comment about the number of RAM banks
mx31: Fix checkpatch warnings in generic.c
mx31: Use proper IO accessor for GPR register
mx31: Remove duplicate definition for GPR register
qong: Use generic function for configuring GPR register
M28EVK: Enable USB HOST support
iMX28: Add USB HOST driver
iMX28: Add USB and USB PHY register definitions
M28: Add memory detection into SPL
iMX28: Fix ARM vector handling
M28: Add doc/README.m28 documentation
M28: Add MMC SPL
iMX28: Add support for DENX M28EVK board
iMX28: Add u-boot.sb target to Makefile
iMX28: Add image header generator tool
iMX28: Add driver for internal RTC
iMX28: Add GPMI NAND driver
iMX28: Add APBH DMA driver
iMX28: Add SPI driver
iMX28: Add GPIO control
iMX28: Add I2C bus driver
iMX28: Add PINMUX control
FEC: Add support for iMX28 quirks
iMX28: Add SSP MMC driver
iMX28: Initial support for iMX28 CPU
MX25: zmx25: GCC4.6 fix build warnings
da850: add new config file for AM18xx
BeagleBoard: config: Switch to ttyO2
OMAP3: Change omap3_evm maintainer
devkit8000: Fix NAND SPL on boards with 256MB NAND
integrator: enable Vpp and disable flash protection
integrator: add system controller header
integrator: make flash writeable on boot
integrator: use io-accessors for board init
integrator: move text offset to config
integrator: pass configs for core modules
ARM: remove superfluous setting of arch_number in board specific code.
SPL: Allow ARM926EJS to avoid compiling in the CPU support code
integrator: do not test first part of the memory
arm: a320: fix broken timer
ARM: define CONFIG_MACH_TYPE for all ronetix boards
dm646x: pass board revision info to kernel
dm646x: add new configuration for dm6467T
arm, davinci: Fix setting of the SDRAM configuration register
arm, davinci: Remove the duplication of LPSC functions
arm, davinci: Rename AM1808 lowlevel functions to DA850
da8xxevm: fix build error
ARM: re-add MACH_TYPE_XXXXXX for VCMA9 board and add CONFIG_MACH_TYPE
fsl_i2c.c: In function 'i2c_init':
fsl_i2c.c:245:7: warning: assignment discards qualifiers from pointer target type
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'master' of git://git.denx.de/u-boot-arm:
Arm: re-introduce the MACH_TYPE_XXXXXX for EB_CPUX9K2 board
arm: jadecpu: Readd MACH_TYPE_JADECPU
at91: defined mach-types for otc570 board in board config file
at91: defined mach-types for meesc board in board config file
mx31pdk: Enable D and I caches
ehci-mxc: remove incorrect comment
README: Fix supported i.MX SoC list for CONFIG_MXC_SPI
mx53: Turn off child clocks before reconfigure perclk_root
qong: enable support for compressed images
imx: imx31_phycore.h: fix checkpatch warnings
vision2: Remove unused get_board_rev function
mx53smd: Remove unused get_board_rev function
mx53ard: Remove unused get_board_rev function
mx53evk: Remove unused get_board_rev function
mx53evk: Add RTC support
mx53loco: Remove unused get_board_rev function
mx53evk: Remove unneeded '1' from mx53evk.h
OMAP3: mvblx: Initial support for mvBlueLYNX-X
ARM: dig297: Define MACH_TYPE_OMAP3_CPS and CONFIG_MACH_TYPE
omap3: mem: Move comments next to definitions
omap3: mem: Clean-up whitespaces
omap3: mem: Define and use common macros
Davinci: ea20: added PREBOOT to configuration
Davinci: ea20: added I2C support
Davinci: ea20: added video support
VIDEO: davinci: add framebuffer to da8xx
ARM: Davinci: added missing registers to hardware.h
Davinci: ea20: add gpios for LCD backlight control
Davinci: ea20: add gpio for keeping power on in board_late_init
Davinci: ea20: Add default U-Boot environment
Davinci: ea20: Add early init to get early output from console
Davinci: ea20: Add NAND support
Davinci: ea20: set GPIOs to hold MII-Phy in reset and set UART0-Switch for console
Davinci: ea20: set console on UART0
arm, davinci: add cam_enc_4xx support
arm926ejs, davinci: add missing spi defines for dm365
arm926ejs, davinci: add cpuinfo for dm365
arm, davinci: add lowlevel function for dm365 soc
arm, davinci: add header files for dm365
spl, nand: add 4bit HW ecc oob first nand_read_page function
arm, davinci: add support for new spl framework
spl: add option for adding post memory test to the SPL framework
net, davinci_emac: make clock divider in MDIO control register configurable
arm, usb, davinci: make USBPHY_CTL register configurable
usb, davinci: add enable_vbus() weak function
omap3evm: fix errors caused by multiple definitions
omap3evm: Add (quick) configuration for NAND only
omap3evm: Add (quick) configuration for MMC/SD only
omap3evm: move common config options to new file
omap3evm: Prepare to split configuration
omap3evm: Reorder related config options
omap/spl: actually enable the console
davinci_emac: compilation fix, phy is array now
omap3evm: Set environment variable 'ethaddr'
arm, arm926: fix missing symbols in NAND_SPL mode
arm, davinci: Add function lpsc_syncreset()
arm, davinci: replace CONFIG_PRELOADER with CONFIG_SPL_BUILD
arm/km: portl2 environment address update to P1B
arm/km: adapt bootcounter evaluation
arm/km: enable jffs2 cmds
arm/km: trigger reconfiguration for the Xilinx FPGA
arm/km: add boardid and hwkey to kernel command line
ARM: Reintroduce MACH_TYPE_KM_KIRKWOOD for keymile ARM boards
netspace_v2: enable I2C EEPROM support
netspace_v2: fix SDRAM configuration
armada100: define CONFIG_SYS_CACHELINE_SIZE
pantheon: define CONFIG_SYS_CACHELINE_SIZE
kirkwood: define CONFIG_SYS_CACHELINE_SIZE
kirkwood: drop empty asm-offsets.s file
arm/km/mgcoge3un: enhance "waitforne" feature
arm/km: add variable waitforne to mgcoge3un
gplugD: Fix for error:MACH_TYPE_SHEEVAD undeclared
ARM: dreamplug: fix compilation
ARM: DockStar: fix compilation
ARM: netspace_v2: fix warnings
am335x: Drop board_sysinfo struct
am335x: Temporarily add MACH_TYPE define
misc:pmic:samsung Enable PMIC driver at C210 Universal target
dcache:s5p CONFIG_SYS_CACHELINE_SIZE added for s5p UNIVERSAL C210 target
dcache:s5p CONFIG_SYS_CACHELINE_SIZE added for s5p GONI target
smdkv310: use macro for mmc data read function address
smdkv310: use spl framework for mmc spl
SMDKV310: use get_ram_size() to validate dram size
SMDKV310: Initialize board id using CONFIG_MACH_TYPE
ORIGEN : use absolute paths and fix tool naming
ORIGEN : enable device tree support
MX25: tx25: Fix building due to missing MACH_TYPE
mx31: Add board support for HALE TT-01
mx31: add ESD control registers
mx31: define pins and init for UART2 and CSPI3
MX35: add support for flea3 board
MX51: vision2: add MACH_TYPE in config file
vision2: Remove unused header file
mx51evk: Remove unused get_board_rev function
mx51evk: Remove unneeded '1' from mx51evk.h
I2C: Fix mxc_i2c.c problem on imx31_phycore
mx35pdk: Add RTC support
mx51evk: Use GPIO API for configuring the IOMUX
mx51evk: Add RTC support
rtc: Make mc13783-rtc driver generic
qong: remove unneeded IOMUX settings
qong: Use mx31_set_gpr to setup USBH2 pins
mx31: Introduce mx31_set_gpr function
mx31pdk: Add MC13783 PMIC support
qong: remove unneeded "1" from qong.h
misc: pmic: fix regression in pmic_fsl.c (SPI)
mx5 configs: CONFIG_PRIME should really be CONFIG_ETHPRIME
MX35: Drop unnecessary prototypes from imx-regs.h
I2C: added I2C-2 and I2C-3 to MX35
MX35: factorize common assembly code
MX35: add reset cause as provided by other i.MX
MX35: add pins definition for UART3
MX35: added ESDC structure to imx-regs
The problem was caused by a global variable being used early in the boot
process.
The symptoms were on imx31_phycore board, reading the environment from I2C
EEPROM didn't work correctly and causes default environment to be loaded.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Heiko Schocher <hs@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
Tested-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Stefano Babic <sbabic@denx.de>
When enable the multi-bus, the current_bus is not inited in the original
implementation, which make the i2c operation unpredicatable.
Signed-off-by: Lei Wen <leiwen@marvell.com>
When DEBUG_I2C is open, the following build issue would shows up.
mv_i2c.c: In function 'i2c_transfer':
mv_i2c.c:257: error: 'ISR' undeclared (first use in this function)
mv_i2c.c:257: error: (Each undeclared identifier is reported only once
mv_i2c.c:257: error: for each function it appears in.)
Signed-off-by: Lei Wen <leiwen@marvell.com>
There are some locations in the code which anticipate printf() being called
before the console is ready by squelching printf() on gd->have_console.
Move this squelching into printf(), vprintf(), puts() and putc(). Also
make tstc() and getc() return 0 if console is not yet initialised
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
Tested-by: Simon Glass <sjg@chromium.org>
Rewrite the mxc_i2c driver.
* This version is much closer to Linux implementation.
* Fixes IPG_PERCLK being incorrectly used as clock source
* Fixes behaviour of the driver on iMX51
* Clean up coding style a bit ;-)
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Jason Hui <jason.hui@linaro.org>
Acked-by: Jason Liu <jason.hui@linro.org>
Acked-by: Heiko Schocher <hs@denx.de>
Tested-by: Jason Liu <jason.hui@linro.org>
This allows the EEPROM layer to send a single i2c write command
per page, and wait CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS between
i2c write commands.
Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Deblock i2c bus when switching to another i2c bus, if using
i2c_set_bus_num().
Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Add the ability to support multiple i2c bus for mv_i2c
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Lei Wen <leiwen@marvell.com>
Add i2c_clk_enable in the cpu specific code, since previous platform it,
while new platform don't need. In the pantheon and armada100 platform,
this function is defined as NULL one.
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Lei Wen <leiwen@marvell.com>
The original 10000 value would be 100ms, which is not
the comments said.
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Lei Wen <leiwen@marvell.com>
For better sharing with other platform other than pxa's,
it is more convenient to put the driver to the common place.
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Lei Wen <leiwen@marvell.com>
As exception among the i.MX processors, the i.MX31 has headers
without general names (mx31-regs.h, mx31.h instead of imx-regs.h and
clock.h). This requires several nasty #ifdef in the drivers to
include the correct header. The patch cleans up the driver and
renames the header files as for the other i.MX processors.
Signed-off-by: Stefano Babic <sbabic@denx.de>
The omap24xx driver only seems to support devices that have a single subaddress
byte. With these types of devices, the first access in a bus transaction is
usually a write (writes the subaddress) followed by either a read or write to
access the devices registers.
Many such devices will respond to a read as the first access, but there are at
least some that will NACK such a read. (e.g. ADV7180.)
The probe function attempts to detect a devices ACK to a read access only and
fails to find devices that NACK a read.
This commit modifies the probe function to start a write instead. This detects
devices that respond to reads (since they must also respond to writes) as well
as those that only respond to writes. The bus is immediately set to idle after a
(N)ACK avoiding actually writing anything to the device.
Signed-off-by: Nick Thompson <nick.thompson@ge.com>
There is sporadic failures when more as one I2C slave
is on the bus and the processor tries to communicate
with more as one slave.
The problem was seen on a mx35pdk (two I2C slaves,
PMIC controller and CAN/RTC chip).
The current driver uses the IIF bit in the status register
to check if the bus is busy or not. According to the manual,
this is not correct, because the IIB bit should be checked.
Not only, to check if a transfer is finished must be checked
the ICF bit, and this is not tested at all.
This patch comes from analyse with a corresponding driver
provided by Freescale as part of the LTIB tool. Comparing
the two drivers, it appears that the current u-boot driver checks
the wrong bits, and depending on race condition, the transfer
can be successful or not.
The patch gets rid also of own debug function (DPRINTF),
replaced with the general debug().
Tested on Freescale mx35pdk.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
This driver accesses to processor's register
via __REG macros, that are removed (or are planned
to be removed) and replaced by C structures.
This patches replaces all occurrencies of __REG macros.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
Make at91 header includes in soft_i2c depend only on CONFIG_AT91FAMILY
rather than individual SoCs.
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Acked-by: Reinhard Meyer<u-boot@emk-elektronik.de>
It can be optimised out by the compiler otherwise resulting
in obscure errors like a board not booting.
This has been documented in README since 2006 when these were
first fixed up for GCC 4.x.
Signed-off-by: John Rigby <john.rigby@linaro.org>
Fix some additional places.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-By: Albert ARIBAUD <albert.aribaud@free.fr>
Before this commit, weak symbols were not overridden by non-weak symbols
found in archive libraries when linking with recent versions of
binutils. As stated in the System V ABI, "the link editor does not
extract archive members to resolve undefined weak symbols".
This commit changes all Makefiles to use partial linking (ld -r) instead
of creating library archives, which forces all symbols to participate in
linking, allowing non-weak symbols to override weak symbols as intended.
This approach is also used by Linux, from which the gmake function
cmd_link_o_target (defined in config.mk and used in all Makefiles) is
inspired.
The name of each former library archive is preserved except for
extensions which change from ".a" to ".o". This commit updates
references accordingly where needed, in particular in some linker
scripts.
This commit reveals board configurations that exclude some features but
include source files that depend these disabled features in the build,
resulting in undefined symbols. Known such cases include:
- disabling CMD_NET but not CMD_NFS;
- enabling CONFIG_OF_LIBFDT but not CONFIG_QE.
Signed-off-by: Sebastien Carlier <sebastien.carlier@gmail.com>
This patch adds generic support for the Samsung s3c2440 processor.
Global s3c24x0 changes to struct members converting from upper case to
lower case.
Signed-off-by: Craig Nauman <cnauman@diagraph.com>
Cc: kevin.morfitt@fearnside-systems.co.uk
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
On OMAP36/37XX the standard on chip pullups are not sufficient to
ensure proper i2c operation without external pullups or switching
to high speed mode and enabling special on chip pullups.
This is an issue for Beagle xM, which does not have external pullups
on the expansion board i2c lines.
The issue manifests itself as an AL (arbitration lost) error when
probing for a non-existent device (i.e. on a Beagle xM with no expansion
boards attached). This issue does not occur on expansion boards that
include pullups or on Overo 37XX COM's since they include pull-ups.
This patch fixes the issue by checking for the AL bit in the i2c_probe
function.
Signed-off-by: Steve Sakoman <steve.sakoman@linaro.org>
This patch removes the "magic number" delays and instead
monitors state changes in the status register bits.
Signed-off-by: Steve Sakoman <steve.sakoman@linaro.org>
Tested-by: Heiko Schocher <hs@denx.de>
This patch removes the "magic number" delays and instead
monitors state changes in the status register bits.
Signed-off-by: Steve Sakoman <steve.sakoman@linaro.org>
Tested-by: Heiko Schocher <hs@denx.de>
This patch removes the "magic number" delays and instead
monitors state changes in the status register bits.
Signed-off-by: Steve Sakoman <steve.sakomanlinaro.org>
Tested-by: Heiko Schocher <hs@denx.de>
This patch matches the poll interval (1 millisecond) and timeout (1 second)
used in the linux driver. It also adds a return value of 0 in the event of
a timeout error and cleans up some formatting errors in that section of the
code.
Signed-off-by: Steve Sakoman <steve.sakoman@linaro.org>
Tested-by: Heiko Schocher <hs@denx.de>
This patch moves some ppc4xx related headers from the common include
directory (include/) to the powerpc specific one
(arch/powerpc/include/asm/). This way to common include directory is not
so cluttered with files.
Signed-off-by: Stefan Roese <sr@denx.de>
This rewrite of the mvtwsi driver is 25% smaller and much
faster and simpler than the previous code.
Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
Acked-by: Prafulla Wadaskar<prafulla@marvell.com>
Acked-by: Heiko Schocher<hs@denx.de>
This driver is not kirkwood-specific and can also be used
e.g. by orion5x. Rename to a SoC-neutral name.
Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
Acked-by: Prafulla Wadaskar<prafulla@marvell.com>
Acked-by: Heiko Schocher<hs@denx.de>
Make the header guard to be generic to stop conflicting with
omap2 i2c header file arch/arm/include/asm/arch-omap24xx/i2c.h
Cc: Steve Sakoman <steve@sakoman.com>
Cc: Heiko <hs@denx.de>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Wolfang Denk <wd@denx.de>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Steve Sakoman <steve@sakoman.com>
This patch modifies the init routine to follow the TRM
recommendations. It also modifies the i2c_read_byte function
to reflect subtle differences between the i2c controller in
OMAP3 and OMAP4.
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Acked-by: Nishanth Menon <menon.nishanth@gmail.com>
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Since the vast majority of GPIO I2C implementations behave the same way,
support the common GPIO framework with default settings.
This adds two new defines CONFIG_SOFT_I2C_GPIO_{SCL,SDA} so that boards
which want GPIO I2C support need only define these.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Tested-by: Thomas Chou <thomas@wytron.com.tw>
This patch modifies the omap24xx driver so that it will also work with OMAP4.
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
In order to do this cleanly, the register accesses have to be converted to
a C struct (base pointer), so do that in the process.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This patch adds a callpoint in i2c_init that allows board specific
i2c board initialization (typically for i2c bus reset) that is called
after i2c_init operations, allowing the i2c_board_late_init function
to use the pre-configured i2c bus speed and slave address.
