Since SCU MU driver has been bound in dm_init, so we don't need to
bind it again. Just replace by using uclass function to probe it.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
To support SPL loading container file, add a new Makefile target,
and introduce a new Kconfig file to source the cfg file which
will be parsed by mkimage.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add parsing i.MX8 Container file support, this is to let
SPL could load images in a container file to destination address.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The changes were added by following patch:
commit <9002e735e717> ("imx: mx6sabresd: fix boot hang with video")
commit <f45ec8fcfb86> ("imx6: dts: add 'u-boot, dm-pre-reloc' to soc and ipu nodes")
Let's move the U-Boot specific change to imx6qdl-u-boot.dtsi
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Move CONFIG_CSF_SIZE to Kconfig and define default value as 0x4000.
mx8mqevk requires 0x2000 add this configuration in imx8mq_evk_defconfig
file.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
On i.MX7ULP B0, there is change in NIC clock dividers architecture.
On A0, the NIC1 BUS and EXT dividers were in a chain with NIC1 DIV, but
on B0 they are parallel with NIC1 DIV. So now the dividers are independent.
This patch modifies the scg_nic_get_rate function according to this change.
Signed-off-by: Ye Li <ye.li@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
The normal target frequency for ULP A7 core is 500Mhz, but now ROM
set the core frequency to 413Mhz. So change it to 500Mhz in u-boot.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The GPU uses APLL PFD2 as its clock parent (483.84Mhz) with divider
set to 1. This frequecy is out of ULP A0 spec. The MAX rate for GPU
is 350Mhz. So we simply configure the APLL PFD2 to 345.6Mhz (FRAC=28)
to workaround the problem. The correct fix should let GPU handle the
clock rate in kernel.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The num/denom is a float value, but in the calculation it is convert
to integer 0, and cause the result wrong.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Wrong I2c driver configuration name is used in codes, so I2c driver is
not built. Correct it.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Since many drivers need this CONFIG_MX7ULP to distiguish the settings
for i.MX7ULP only. Add this entry to cpu's kconfig.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The offset for FRAC and the mask for PCD are not correct.
If we set FRAC, we can't get the right frequency. Fix them
to correct value.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
On i.MX7ULP, value zero is reserved in SCG1 RCCR register,
so the val should be decreased by 1 to get the correct clock
source index.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The board will reboot if A7 core enter mem mode by rtc, then M4 core
enter VLLS mode after the RTC alarm expired. Enable the dumb PMIC mode
to fix this issue.
Since i.MX7ULP B0 moves the SNVS LP into M4 domain, A core can't access
it. So check the CPU rev and not apply the settings for B0.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Previously the SPL size on all iMX6 platforms was restricted to 68KB
because the OCRAM size on iMX6SL/DL parts is only 128KB. However, the
other iMX6 variants have 256KB of OCRAM. Add an option
CONFIG_MX6_OCRAM_256KB which allows using the full size on boards which
don't need to support the SL/DL variants. This allows for an SPL size of
196KB, which makes it much easier to use configurations such as SPL with
driver model and FDT control.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Tested-by: Adam Ford <aford173@gmail.com> #imx6q_logic
There is no need to use HAB for FIT signature validation when
SPL_FIT_SIGNATURE is also enabled, as that will be validated via the
normal U-Boot signed FIT image flow.
This allows having SPL validated by HAB and the payloads to follow
being validated with FIT signatures only.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Toradex Apalis iMX6 modules are available in the iMX6D and iMX6Q
variants, which are quite similar and already managed via only one
dtb in u-boot (imx6-apalis.dtb). Select MX6Q via Kconfig by default in
order to automatically enable the HAS_CAAM and MX6_SMP features.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
The gpio command currently uses equal bank names "GPIO0_"
for all existing gpio banks, i. e.:
U-Boot# gpio status -a
Bank GPIO0_:
GPIO0_0: input: 0 [ ]
GPIO0_1: input: 0 [ ]
...
Bank GPIO0_:
GPIO0_0: input: 0 [ ]
GPIO0_1: input: 0 [ ]
...
So the command is broken, it is not possible to address
a desired bank. Add gpio aliases to fix this.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Pass spl_image and bootdev to board_return_bootrom.
i.MX8MN needs the args to let ROM to load images
Cc: Simon Glass <sjg@chromium.org>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
To support DM_VIDEO,
Add display node for lcdif
Drop board iomuxc settings.
Enable DM_VIDEO
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Add i.MX6ULZ board support. the i.MX6ULZ is SW compatible
with i.MX6ULL. so most code of i.MX6ULL can be reused
by i.MX6ULZ.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add i.MX6ULZ cpu type and helper.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Import kernel dts for i.MX6ULZ from
commit <0a8ad0ffa4d8> ("Merge tag 'for-linus-5.3-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Sync kernel dts for i.MX6ULL from
commit <0a8ad0ffa4d8> ("Merge tag 'for-linus-5.3-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Sync kernel dts for i.MX6UL from
commit <0a8ad0ffa4d8> ("Merge tag 'for-linus-5.3-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Move the exisiting function of getting board dtb from versal to a common
Xilinx folder.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
With new mailbox driver PMUFW configuration object can be loaded via the
same interface and there is no need to have pmu_ipc.c completely.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Probe ZynqMP firmware driver on the board initialization phase and
ensure that firmware is in place to continue execution. The probing is
done on board_init so it can be used for both SPL and U-Boot proper.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Removes the old function to get the firmware version.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
New firmware header to place firmware specific macro and function
declarations. The patch also moves the macros defining PM operations as
well as some helper macros.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Cleanup PM ID handling by using enum values.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The following patch adds a mailbox node and firmware node to following the
mainline DT.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
zynqmp-power driver for ZynqMP to handle the communication with the PMU
firmware. Firmware driver just probes subnodes and power driver handles
communication with PMU using the IPI mailbox driver.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
ZynqMP mailbox driver implementing IPI communication with PMU. This would
allow U-Boot SPL to communicate with PMUFW to request privileged
operations.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Similar SCs but different wiring.
- dc_i2c is connected to X-PRC cards that's why label is required to have
an option to hook up some devices.
- Exactly identify i2c devices on x-prc boards.
In case of missing i2c connection devices won't be accessible.
- USB 0 should be device mode with super speed.
- USB 1 should be host mode.
- Fix i2c mux reset pin entry - commented, not verified.
- Fix i2c1 eeprom compatible string - it is an ST 128Kbit device.
Need to use atmel fallback.
- Fix si570 I2C slave address and add corresponding part numbers.
- Enable AMS for system monitoring.
- phy reset property should be commented because it will throw a
warning dump when called from context that can sleep.
No support for phys property (zynqmp phy driver) with SGMII.
Add is-internal-pcspma property required by uboot.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Change has been done across the whole tree only zynqmp-mini-qspi hasn't
been fixed.
Origin changed done by commit ffd4c7c2ec
("dts: switch spi-flash to jedec, spi-nor compatible")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch added alias for usb node in dts file.
Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds clock driver support for Versal platform. The clock driver
queries and performs clock operations using PLM firmware by communicating
with it using SMC calls.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch provides an option to enable/disable OCM and TCM memory into MMU
table with corresponding memory attributes.
The same change was done for ZynqMP by commit 189bec47ab
("arm64: zynqmp: Provide a Kconfig option to define OCM and TCM in MMU")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Code reads DT and setup MMU table based on memory node. This will ensure
that only DT needs to be changed.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch is setting up the initrd_high to as high as possible by leaving
max stack size for u-boot so that bigger rootfs can also be loaded by
u-boot for booting kernel.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch is setting up the initrd_high to as high as possible by leaving
max stack size for u-boot so that bigger rootfs can also be loaded by
u-boot for booting kernel.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Define board_late_init which performs bootmode detection
and prepares corresponding distro boot commaand sequence.
Also disable it for mini platforms because simply there is no need to have
it enabled.
But also disable it for virtual platform because Qemu is not modelling this
register space that's why travis testing would fail. This configuration
should be reverted when mainline Qemu is updated.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This node is used by qspi driver for supporting qspi boot mode in SPL.
Similar changes have beeen done by commit a9022b017a
("ARM64: zynqmp: Add u-boot,dm-pre-reloc to clk nodes")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The sam9x60 qspi controller uses 2 clocks, one for the peripheral register
access, the other for the qspi core and phy. Both are mandatory.
Enable the qspi node together with the SST26VF064B qspi nor flash
memory. Booting from the QSPI NOR flash is now possible.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
sama5's SFR has at offset 0x04 the DDR Configuration Register,
while sam9x60's SFR contains the EBI Chip Select Register. Add
a union to reconcile both boards.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
The Special Function Registers (SFR) are present in sam9x5 and
sam9x60 too, rename sama5_sfr to at91_sfr.h.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Add new board SAM9X60-EK using the ARM926 SAM9X60 SoC.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
[tudor.ambarus@microchip.com:
- fix number of DRAM banks:
One DDR2-SDRAM (W972GG6KB 2 Gbit = 16 Mbit x 16 x 8 banks]
- drop SPL related macros
- drop memtest macros
- drop CONFIG_SPI_BOOT, CONFIG_SYS_USE_DATAFLASH related macros
- drop inclusion of asm/arch/at91sam9_smc.h]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Add Ethernet controller to dtsi file and enable it on sam9x60ek
platform connected with rmii.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
add device tree files for sam9x60ek board with below changes.
- Add initial device nodes (pmc, pinctrl, sdhc, dbgu & pit)
- Add the reg property for the pinctrl node.
- Add the "u-boot,dm-pre-reloc" property to determine which nodes
are used by the board_init_f stage.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
[prasanthi.chellakumar@microchip.com: fix style/whitespace issues]
Signed-off-by: Prasanthi Chellakumar <prasanthi.chellakumar@microchip.com>
[nicolas.ferre@microchip.com:
- fix gclk,
- fix pio/pinctrl controller definition and allow to have more
than only PIOA for this SoC,
- removing pinctrl address]
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
[claudiu.beznea@microchip.com:
- use SAM9X60's compatible for pinctrl
- add drive strength and slew rate options for SDMMC0 pins.]
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
[tudor.ambarus@microchip.com:
- u-boot,dm-pre-reloc property in dedicated file,
- fix pit len, starts from 0xFFFFFE40 and it is of len 0x10]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Add node for hlcld for u-boot logo display at boot.
This is compatible with the Precision Design Associates (PDA) TM5000 screen.
Timings are compatible with simple panel from Linux, panel name is
pda_91_00156_a0
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
qspi1 does not have an alias/seq number. This is required for
SPL default SF bus booting for the boards that have this SoC
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Add a function in SFR implementation that will open the DDR input
buffers.
This can be called at DRAM initialization time.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Add support for the SAMA5D27-WLSOM1-EK. It's based on the Microchip
WireLess SoM which contains the SAMa5D27 LPDDR2 2Gbits SiP.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
[eugen.hristev@microchip.com]: added u-boot specific dtsi and ported to 2019.10
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
This is currently a decimal value which is not as convenient or
meaningful. Also U-Boot tends to use hex everywhere.
Convert this option to hex and add a comment for the size_check macro.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: correct the typo in the commit title]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
At present there is only one control for this and it is used for both SPL
and TPL. But SPL might have a lot more space than TPL so the extra cost of
a full printf() might be acceptable.
Split the option into two, providing separate SPL and TPL controls. The
TPL setting defaults to the same as SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present this is defined in Kconfig but there is a separate one in the
CONFIG whitelist. It looks like these are duplicates.
Rename the non-Kconfig one and remove it from the whitelist.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
We have a 'safe' version of this function but sometimes it is not needed.
Add a normal version too and update a few places that can use it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This reverts commit 0797f7f0b7.
Tegra specific solution is not required any more as efi core has been
made aware of ram_top with the following commit:
7b78d6438a efi_loader: Reserve unaccessible memory
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
The SPL device tree is missing the entires for gpio1, uart1, usdhc1 and
usdhc2. This creates the missing imx6q-logicpd-u-boot.dtsi file
which will enable these functions so SPL can properly setup UART, detect
microSD card, and startup.
Fixes: 8f4691e31a ("ARM: imx6q_logic: With SPL_OF_CONTROL enabled,
remove MMC init")
Signed-off-by: Adam Ford <aford173@gmail.com>
On HS devices the access to TRNG is restricted on the non-secure
ARM side, disable the node in DT to prevent firewall violations.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
The memory allocated to store the FIT image containing SYSFW and board
configuration data is statically defined to the largest size expected.
This was 269000 bytes but now needs to be grown to 276000 to make room
for the signatures attached to the board configuration data on High
Security devices.
Signed-off-by: Andrew F. Davis <afd@ti.com>
This patch restores commit c49d0ac38a ("ARM: dts: rmobile: Increase off-on
delay on the SD Vcc regulator"), which was accidentally dropped during DT
resync in commit 317d13ac63 ("ARM: dts: rmobile: Synchronize Gen3 DTs with
Linux 5.0").
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Fixes: 317d13ac63 ("ARM: dts: rmobile: Synchronize Gen3 DTs with Linux 5.0")
The commit 619f002db8 ("rockchip: make_fit_atf.py: fix loadables property
set error") fixed the double-loading of the primary atf-image, but didn't
take into account that there may be rare atf images with only that main
section present.
Right now this will result in a broken its due to the loadables section not
getting closed correctly, so fix that by adapting the guards around the loop.
The guards now protect against 0 segments when the bl31 binary doesn't
contain any section and 1 segment when only a core atf section is present.
Fixes: 619f002db8 ("rockchip: make_fit_atf.py: fix loadables property set error")
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
Originally the cpuid var the value gets read into was defined as
u8 cpuid[RK3399_CPUID_LEN];
hence the sizeof(cpuid) would return the correct the correct number
of array elements.
With the move to a separate function cpuid becomes a pointer and
sizeof(cpuid) hence returns the pointer size - 8 in the arm64 case.
We do have the actual id length available as function param so use
it for actual amount of bytes to read.
Fixes: 0482538499 ("rockchip: rk3399: derive ethaddr from cpuid")
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
Tinker board needs to mux all the sdmmc gpio and
activate the regulator connected to bank 7. Remove
all the bank that are not in use and mark them as dm,spl
so-that it would initialize at SPL.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
newline \n was missed in fdt_path_offset, error loop.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
ROCKCHIP_BROM_HELPER is selected as if TPL/SPL ROCKCHIP_BACK_TO_BROM
has been defined, so drop the explicit enablement for vyasa board.
This change is supposed to missed during config move to
other locations, and missed to drop the same.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
According to the latest am572x[1] and dra74x[2] data manuals, mmc3
default, hs, sdr12 and sdr25 modes use iodelay values given in
MMC3_MANUAL1. Set the MODE_SELECT bit for these so that manual mode is
selected and correct iodelay values are configured.
[1] http://www.ti.com/lit/ds/symlink/am5728.pdf
[2] http://www.ti.com/lit/ds/symlink/dra746.pdf
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
API get_ti_sci_handle() is relying on the device-tree node name
to be "dmsc" for probing the ti_sci device. But with the introduction
of debug messages for dmsc, the node name changed to dmsc@44083000.
Because of this ti_sci is never probed cause a boot failure. Instead
of relying on device-tree node name, use the first available firmware
node for probing ti_sci.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The da8xx GPIO driver is available with DM_GPIO support. This
patch enables the CMD_GPIO, CMD_DM, and DM_GPIO and DA8XX_GPIO.
Signed-off-by: Adam Ford <aford173@gmail.com>
Add device tree from Linux for driver model conversion
and enable OF_CONTROL. This will remove the following compile
warning:
==================================================
Device Tree Source is not correctly specified.
Please define 'CONFIG_DEFAULT_DEVICE_TREE'
or build with 'DEVICE_TREE=<device_tree>' argument
===================================================
Target was compile tested, build was clean.
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
In SerDes protocol 0x13BB, lane C was erroneously assigned
to PCIE1, this is now updated to PCIE2
Fixes: 36f50b7523 ("armv8: ls1028a: Add other serdes
protocal support")
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The correct config entry is CONFIG_PCIE_LAYERSCAPE and this
typo results in skipping the fixup of Linux PCIe DT nodes.
Also enable the fixup when Layerscape Gen4 controller driver
is enabled.
Fixes: 4da0e52c9d (armv8: fsl-layerscape: fix config dependency
for layerscape pci code)
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
By default, i2c input clock is programmed at
platform clk / 2 in u-boot, but this is not
correct for all the platforms,
Update I2C clock divider's default values as per
SoC (LS1012A, LS1028A, LX2160A and LS1088A).
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The SP805-WDT module on LS1028A requires configuration of PMU's
PCTBENR register to enable watchdog counter decrement and reset
signal generation. The watchdog clock needs to be enabled first.
Signed-off-by: Thomas Schaefer <thomas.schaefer@kontron.com>
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add the device-tree structure describing the MUX in board dts.
QDS board has an on-board RGMII PHY and 4 slots for extension cards.
All these can be accessed over MDIO through a MDIO MUX controlled
over I2C.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Use obj-$(config) instead of #ifdef $config to make the code looks
clean, and move the misc_init for U-Boot proper only.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The rk3188/Makefile already depends on !TPL_BUILD, so no need to add
this again in parent Makefile, remove it.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
- fix bcm2835_sdhost to wait long enough for a transfer to complete
- increase kernel image size from 8 MB to 64 MB on arm64
- add support for RPi4
- add prefixes for raspberry pi related stuff to git-mailrc
-----BEGIN PGP SIGNATURE-----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=hWTf
-----END PGP SIGNATURE-----
Merge tag 'rpi-next-2019.10' of https://github.com/mbgg/u-boot
- fix mailbox status register used for polling
- fix bcm2835_sdhost to wait long enough for a transfer to complete
- increase kernel image size from 8 MB to 64 MB on arm64
- add support for RPi4
- add prefixes for raspberry pi related stuff to git-mailrc
This clock has a different mbox ID so have this included in the relevant
header file.
Signed-off-by: Andrei Gherzan <andrei@balena.io>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Define two target configs for Raspberry Pi 4 (32 and 64bit) and the
corresponding BCM2838* configs.
Be aware of the current limitation in firmware which requires an
explicit configuration to force the arm in 64bit mode when the
respective target is used.
Signed-off-by: Andrei Gherzan <andrei@balena.io>
[mb: rename BCM2838 -> BCM2711]
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Devices of bcm283x have different base address, depending if they are on
bcm2835 or bcm2836/7. Use BCM283x_BASE depending on the SoC you want to
build and only add the offset in the header files.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: Andrei Gherzan <andrei@balena.io>
Before we can send a message to the mailbox we have to check that there
is space to do so. Therefore we poll the status register. But up to now
the wrong status register, the one of mailbox 0, was checked. Fix this
by polling the status regiser of mailbox 1.
Signed-off-by: Fabian Vogt <fvogt@suse.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
[mb: rename registers and update commit message]
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Add nodes for the Aspeed SD controllers with their necessary properties.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Implicitly Marvell MDIO driver uses DT node names for devices, but in this
case that is not unique. Set MDIO device names for master/slave to
cpm/cps.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Create drivers/net/fsl-mc/Kconfig and move fsl-mc specific configs
from arch/arm/cpu/armv8/fsl-layerscape/Kconfig to this new Kconfig
Signed-off-by: Florinel Iordache <florinel.iordache@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
When CONFIG_CLK enabled, use CLK UCLASS for clk related settings.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
hs: removed hunk in mxc_i2c_probe() as not longer in code
This reverts commit fc04b92354 where the
FVP DRAM configuration was added.
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
The current code in reserve_noncached() has two issues:
1) The first update of gd->start_addr_sp always rounds down to a section
start. However, the equivalent calculation in cache.c:noncached_init()
always first rounds up to a section start, then subtracts a section size.
These two calculations differ if the initial value is already rounded to
section alignment.
2) The second update of gd->start_addr_sp subtracts exactly
CONFIG_SYS_NONCACHED_MEMORY, whereas the equivalent calculation in
cache.c:noncached_init() rounds the noncached size up to section
alignment before subtracting it. The two calculations differ if the
noncached region size is not a multiple of the MMU section size.
In practice, one/both of those issues causes a practical problem on
Jetson TX1; U-Boot triggers a synchronous abort during initialization,
likely due to overlapping use of some memory region.
This change fixes both these issues by duplicating the exact calculations
from noncached_init() into reserve_noncached().
However, this fix assumes that gd->start_addr_sp on entry to
reserve_noncached() exactly matches mem_malloc_start on entry to
noncached_init(). I haven't traced the code to see whether it absolutely
guarantees this in all (or indeed any!) cases. Consequently, I added some
comments in the hope that this condition will continue to be true.
Fixes: 5f7adb5b1c ("board_f: reserve noncached space below malloc area")
Cc: Vikas Manocha <vikas.manocha@st.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Alignment with kernel patch proposal for binding:
[PATCH v4 0/8] stm32 m4 remoteproc on STM32MP157c
https://lkml.org/lkml/2019/5/14/159
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Since the commit 8729b1ae2c ("misc: Update read() and
write() methods to return bytes xfered"); The misc bsec driver
need to be adapted to reflect the number of transferred bytes.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Due to kernel DT alignment, pwr-supply is renamed to vdd-supply
and is a subnode of pwr-regulators.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
As for Audio codec IC, HDMI IC is not "IO safe".
HDMI regulators (v3v3 and v1v2) must be enabled to allow
I2C1 bus usage. HDMI IC must be under reset during power up
and keep HDMI and AUDIO devices in reset while they are not
used in U-Boot to keep them in low power mode
(each device can be kept in reset independently keeping their
power supplies ON until kernel).
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add the boot for NOR, SPL load U-Boot.img at offset
CONFIG_SYS_SPI_U_BOOT_OFFS = 0x80000.
It is the start address of mtd partition ssbl in nor.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add imply for FDT overlay that can be usefuill for kernel device tree
management but it is not mandatory (can be removed to gain space)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Depending on backup register value, we maintain the debug unit
powered-on for debugging purpose.
Only BUCK1 is required for powering the debug unit, so revert
the setting for all the other power lanes, except BUCK3 that
has to be always on.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Avoid U-Boot auto-boot interruption for line break detection
on console when the RX line connected to STLINK is floating
(-IO error in getc cause by framing error and testc return 1)
Same workaround is applied on all the STMicroelectonics board.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
The pre-relocation probe is needed to reserve video frame buffer
in video_reserve() for all the board;
LDTC must be tagged prereloc in SOC U-Boot dtsi file.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add node in DT and avoid error to search UCLASS_SYSRESET in
board_f.c::print_resetinfo() and lost 1.6s in U-Boot
for the trusted boot chain.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This patch adds independent watchdog support for stm32mp157c
in SPL.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Update DDR configuration with the latest update:
- Change DQSGE to 1 for DDR3, to cure missing DQS preamble.
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
When the pinmux configuration was added, it was accidentally placed into
the omap3_pmx_wkup node when it should have been placed into the
omap3_pmx_core. This error was accidentally propagated to U-Boot by
me when I blindly copied the device tree from Linux.
This patch moves the i2c2_pins and i2c3_pins to the correct node
which should eliminate i2c bus errors and timeouts due to the fact
the bootloader uses the save device tree that no longer properly
assigns these pins.
Signed-off-by: Adam Ford <aford173@gmail.com>
This converts the following to Kconfig:
CONFIG_ARCH_CPU_INIT
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Tested-by: Felix Brack <fb@ltec.ch>
- remove rk3288 fennec board
- remove SPL raw image support for Rockchip SoCs
- add common misc_init_r() for ethaddr from cpuid
- enable USB HOST support for rk3328
- unify code for finding a valid gpt in part driver
Several options are presenting themselves on a various boards
where the options are clearly not used. (ie, arm64 options on
arm9, or SPL/TPL options when SPL or TPL are not defined)
This patch is not attempting to be a complete list of items, but
more like low hanging fruit.
This patch attempts to reduce some of the menuconfig noise
by defining dependencies so they don't appear when not used.
Signed-off-by: Adam Ford <aford173@gmail.com>
Generate a MAC address based on the cpuid available in the efuse
block: Use the first 6 byte of the cpuid's SHA256 hash and set the
locally administered bits. Also ensure that the multicast bit is
cleared.
The MAC address is only generated and set if there is no ethaddr
present in the saved environment.
This is based off of Klaus Goger's work in 8adc9d
Signed-off-by: Rohan Garg <rohan.garg@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
According to rock64 schemetic, both VCC_HOST1_5V and VCC_HOST_5V are
controlled by USB20_HOST_DRV(GPIO0A2), fix it so that we can get correct
power supply for USB HOST ports.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Enable USB host support on GR Peach board.
To use USB host on GR Peach, it might be necessary to solder JP3 header
onto the board first and then short it. Shorting JP3 is mandatory to let
the U5 regulator to supply VBUS to the CN3 USB port.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Add ICID setup for the platform devices contained on this chip: usb,
sata, sdhc, sec. The ICID macros for SEC needed to be adapted because
the format of the registers is different.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
The current implementation assumes that the registers holding the ICIDs
are universally big endian. That's no longer the case on newer
platforms so update the code to take into account the endianness of
each register.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
By default, i2c input clock is platform clk / 2, but some of the
platform of i2c clock divider does not meet this kind of circumstance,
so alone to set default values for these platforms.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Enable related configs on all ls1088aqds boards to support pcf2127
rtc DM function.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Add the pcf2127-rtc node under the i2c0->i2c-mux@77->i2c@3 for ls1088aqds boards.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
This patch adds some slave nodes to support the i2c dm on the device
side under the i2c0 controller.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
One ls1088a, there are four I2C controllers. So add all I2C node
for ls1088a in device tree.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
As no gpio.h is defined for this architecture, to avoid
compilation failure, do not include <asm/arch/gpio.h> for
arch ls1088a.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Enable related configs on all ls2088aqds boards to support ds3231
rtc DM function.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Add the ds3232-rtc node under the i2c0->i2c-mux@77->i2c@0 for ls2088aqds
boards.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Add some slave nodes to support the i2c dm on the device side under the i2c0.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
One ls2088a, there are four I2C controllers. So add I2C nodes in dts
for ls2088a.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
As no gpio.h is defined for this architecture, to avoid
compilation failure, do not include <asm/arch/gpio.h> for
arch ls2080a.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Add the pcf2127-rtc node under the i2c1 in dts for ls1028aqds boards.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Add pca9547 node to support i2c multiplexer under the i2c0 controller
in dts for ls1028aqds boards.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Enable related configs on all ls1028aqds boards to support pcf2127
rtc DM function.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Alex Marginean <alexm.osslist@gmail.com>
Tested-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Add some slave nodes to support the i2c dm on the device side under the i2c0.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
As no gpio.h is defined for this architecture, to avoid
compilation failure, do not include <asm/arch/gpio.h> for
arch ls1028a.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Enable related configs on all lx2160ardb boards to support pcf2127
rtc DM feature.
Also remove SYS_I2C_MXC_I2Cx, where x is from 1 to 8 from
Kconfig.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Add the pcf2127-rtc node under the i2c0->i2c-mux@77->i2c@3 in dts for
lx2160aqds boards.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Lx2160ardb need to use i2c0 before relocation, so we also need to set
u-boot, dm-pre-reloc to initialize node before relocation.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Adds the pcf2127-rtc node under the i2c4 node dts of lx2160ardb boards.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
In lx2160a soc, there are eight i2c controllers, this patch adds i2c
nodes for lx2160a, and the gpio2 nodes on which the i2c4 controller
depends.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
As no gpio.h is defined for this architecture, to avoid
compilation failure, do not include <asm/arch/gpio.h> for
arch ls2160a.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
I2C dm mode enablemenet causes below compilation errors:
In file included from include/config.h:8:0,
from include/common.h:20:
include/config_fallbacks.h:51:4: error: #error "Cannot define
CONFIG_SYS_I2C when CONFIG_DM_I2C is used"
# error "Cannot define CONFIG_SYS_I2C when CONFIG_DM_I2C is used"
^~~~~
In file included from include/config.h:8:0,
from include/common.h:20:
include/config_fallbacks.h:51:4: error: #error "Cannot define
CONFIG_SYS_I2C when CONFIG_DM_I2C is used"
# error "Cannot define CONFIG_SYS_I2C when CONFIG_DM_I2C is used"
^~~~~
board/freescale/lx2160a/lx2160a.c: In function 'board_early_init_f':
board/freescale/lx2160a/lx2160a.c:108:2: warning: implicit declaration
of function 'i2c_early_init_f'; did you mean 'arch_early_init_r'?
[-Wimplicit-function-declaration]
i2c_early_init_f();
^~~~~~~~~~~~~~~~
arch_early_init_r
drivers/i2c/mxc_i2c.c: In function 'mxc_i2c_probe':
drivers/i2c/mxc_i2c.c:824:8: warning: implicit declaration of function
'enable_i2c_clk';
did you mean 'enable_irq_wake'? [-Wimplicit-function-declaration]
ret = enable_i2c_clk(1, bus->seq);
^~~~~~~~~~~~~~
enable_irq_wake
So fix these compilation errors.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Select BOARD_LATE_INIT for ls1028ardb and ls1028aqds targets
so that late init work can be done.
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
TI HS platforms generate *dtb_HS binary blobs and there is no
rule for cleanup. Added entry for cleanup in clean-files target.
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
The commit 1b42ab3eda ("ARM: DRA7: Fixup DSPEVE, IVA and GPU clock
frequencies based on OPP") updates the kernel device-tree blob to adjust
the DSP, IVA and GPU DPLL clocks based on a one-time OPP choice selected
in U-Boot. All these DPLL clocks are children of the cm_core_aon clocks
DT node.
The hierarchy of this clocks DT node has changed in newer Linux kernels
starting from v5.0, and this results in a failure in ft_fixup_clocks()
function to update the clock rates on these newer kernels. Fix this by
updating the lookup logic to look through both the newer and older
DT hierarchy paths for the cm_core_aon clocks node.
Signed-off-by: Suman Anna <s-anna@ti.com>
This is a generic implementation. Add CONFIG_SYSRESET_CMD_POWEROFF
to signal when we need it. Enable it from the STPMIC1 config and in
sandbox.
The config flag is transitionary, that is it can be removed after all
poweroff implementations use sysreset, and just have CMD_POWEROFF depend
on sysreset.
Signed-off-by: Urja Rannikko <urjaman@gmail.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
It seems that SYSRESET_POWER_OFF was added recently, and all previous code
used SYSRESET_POWER for poweroff. SYSRESET_POWER is supposed to be a
PMIC-level power cycle, not a poweroff.
(Comment by Simon Glass)
SYSRESET_POWER means to do a power reset (removing and reinstating all power)
SYSRESET_POWER_OFF means to turn the device off and leave it off
Signed-off-by: Urja Rannikko <urjaman@gmail.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
(Update comment to help understand the patch)
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The socfpga gen5 SPL manually zeroed bss in board_init_f(). Now that the
DDR driver does not use bss any more, bss is not used before board_init_r()
and we can remove this hack.
bss is normally zeroed by crt0.S, but after board_init_f(), before
board_init_r(). socfpga just had this double-zeroing because it invalidly
used bss in board_init_f() already (during DDR initialization).
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
A previous commit...
commit 2a51e16bd5 ("configs: Make USE_TINY_PRINTF depend on SPL||TPL and be default")
...causes the System Firmware version string during SPL boot to no longer
getting printed to the console as expected. To fix this issue rework the
handling of that string to only use basic printf() syntax rather than
for example disabling CONFIG_USE_TINY_PRINTF on affected devices, this
way maintaining most of the memory size benefit the initial patch brings
when it comes to SPL.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add needed device-tree nodes to support PCIe 0
and SERDES on AM65x SoC. The nodes are kept
disabled by default.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This commit adds support for the B&R brsmarc1 SoM.
The SoM is based on TI's AM335x SoC.
Mainly vxWorks 6.9.4.x is running on the board,
doing some PLC stuff on various carrier boards.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
This patch disables DM watchdog support for SPL builds and uses
the legacy omap watchdog driver on TI AM335x chipsets.
The following build error is reported if DM watchdog support was
enabled in SPL:
CC spl/drivers/usb/gadget/rndis.o
LD spl/drivers/usb/gadget/built-in.o
LD spl/drivers/usb/musb-new/built-in.o
LD spl/drivers/built-in.o
LD spl/u-boot-spl
arm-linux-ld.bfd: u-boot-spl section .u_boot_list will not fit in region .sram
arm-linux-ld.bfd: region .sram overflowed by 440 bytes
make[1]: *** [spl/u-boot-spl] Error 1
make: *** [spl/u-boot-spl] Error 2
Adjusted WATCHDOG_RESET macro accordingly. Earlier it was pointing
to hw_watchdog_reset. Since CONFIG_WATCHDOG replaces CONFIG_HW_WATCHDOG,
now WATCHDOG_RESET macro points to watchdog_reset. This watchdog_reset
is not defined anywhere for am33xx/omap2 and needs to be defined. Fixed
this by simply calling hw_watchdog_reset in watchdog_reset.
Built and tested on AM335x device (BeagleboneBlack), compile tested for
all other AM33xx/omap2 based boards.
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
[trini: Fix watchdog.h logic]
Signed-off-by: Tom Rini <trini@konsulko.com>
This patch adds device tree and driver model watchdog support,
converts the legacy omap watchdog driver to driver model for
TI AM335x chipsets. The following compile warning is removed:
===================== WARNING ======================
This board does not use CONFIG_WDT (DM watchdog support).
Please update the board to use CONFIG_WDT before the
v2019.10 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
CONFIG_HW_WATCHDOG is no more a default option for AM33XX devices
after DT/DM conversion, adjusted kconfig accordingly.
DM watchdog support is enabled by default in SPL. The SPL image
doesn't fit into SRAM because of size constraints and build breaks
with an overflow. For this reason DM watchdog support should be
disabled in SPL, driver code should be adjusted accordingly to serve
this purpose.
Built and tested on AM335x device (BeagleboneBlack), compile tested
for all other AM33xx based boards.
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
Add support for fastboot_set_reboot_flag() by storing the reboot
flag in the common code to be used by the custom PSCI reboot handler.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The Secure Monitor offers multiple services, like returning the
SoC unique serial number, and can provide the "reboot reason" as
set by the previous booted system.
This extends the Amlogic specific "sm" cmd with a "reboot_reason" subcommand
to print or set a specified environment variable with the reboot reason in
human readable format.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The Secure Monitor offers multiple services, like returning the
SoC unique serial number, already used to generate an unique MAC
address.
This adds a new, Amlogic specific, "sm" cmd with a "serial" subcommand
to write the SoC unique serial to memory.
This "cm" command will be extended in further patches.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Import Linux 5.2-rc1 sei510 DT from 5f9e832c1370 ("Linus 5.3-rc1") for the
meson-g12a-sei510 board.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Activate the driver model for the serial interface in the KM Kirkwood
Kconfig file. The associated preprocessor definitions could be removed
from the header file. However, the clock of 200 MHz needs to be declared
in the device tree.
Signed-off-by: Pascal Linder <pascal.linder@edu.hefr.ch>
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This file contains lots of internal details about the environment. Most
code can include env.h instead, calling the functions there as needed.
Rename this file and add a comment at the top to indicate its internal
nature.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
[trini: Fixup apalis-tk1.c]
Signed-off-by: Tom Rini <trini@konsulko.com>
This header file is now only used by files that access internal
environment features. Drop it from various places where it is not needed.
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Move these functions to the new header file and rename set_default_env()
to env_set_default() so that it has a consistent env_ prefix.
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Move env_set_hex() over to the new header file along with env_set_addr()
which uses it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This commit adds board support for Hikey960 board from Hisilicon. This
board is one of the Consumer Edition boards of the 96Boards family
powered by Kirin960 SoC.
More information about this board can be found in 96Boards website:
https://www.96boards.org/product/hikey960/
The initial supported/tested devices include:
- Debug serial
- SD
With these support, it's good enough for loading Linux Kernel from SD.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
This commit adds devicetree for Hikey960 board. Most of the contents are
copied from Linux kernel with some modifications for u-boot. To be
more precise, SD card's speed related properties are removed due to a
bug in u-boot clock implementation. Hence forcing the SD controller to
work in standard speed.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Add a few bits of platform code to support R8A77980 V3H SoC.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Import R8A77980 V3H DTs and headers from Linux 5.2.7 , commit 5697a9d3d55f.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Support the V1.2 hardware revision with the following pin muxing
changes:
Ddc_scl_pv4 and ddc_sda_pv5 previously used as Apalis GPIO3 and GPIO4
are now used as DDC pins.
Gen2_i2c_scl_pt5 and gen2_i2c_sda_pt6 previously used as DDC pins are
now used as USB power enable signals.
Usb_vbus_en0_pn4 and usb_vbus_en1_pn5 previously used as USB power
enable signals are now used as GPIO3 and GPIO4.
Additionally a new device tree file tegra124-apalis-v1.2-eval.dtb is
loaded on V1.2 and later modules and resp. USB power enable signals
activated.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
When mainline kernels reboot TK1 they use SW_RESET,
that reset mode does not reset PMIC. Some rails
need to be off for RAM Re-repair to work correctly.
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Dominik Sliwa <dominik.sliwa@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
- Add rk3399 boards Khadas Edge/-V/-Captain
- Add fully souce code support for rk3328 including TPL/DRAM init
- Enable boot from eMMC for rk3399 rock960/ficus boards
- turn on the IO supply for dw_mmc
This adds missing hifsys reset parts in header files.
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
The original mtk_qspi driver has been removed. We change MT7629 to use
newly added mtk-spimem driver.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Enable TPL support and some related option in Kconfig.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
[cherry picked from commit 430b01462b with minor modifications]
Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update dmc node for full feature driver.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
[cherry picked from commit 1e14956365 with minor modifications]
Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This driver supports DDR3/LPDDR3/DDR4 SDRAM initialization.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
[cherry picked from commit 9fb0777ec3 with minor modifications]
Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Split u-boot specific dts configuration to separate
rk3328-evb-u-boot.dtsi
Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This commits enables booting from eMMC when using SPL on 96Boards
Ficus board by adding SDHCI to boot order. Since the SDHCI driver
already has the reloc flag, this works straightaway. While we are at it,
let's also include the common u-boot dtsi for rk3399.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This commits enables booting from eMMC when using SPL on 96Boards
Rock960 board by adding SDHCI to boot order. Since the SDHCI driver
already has the reloc flag, this works straightaway. While we are at it,
let's also include the common u-boot dtsi for rk3399.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add devicetree support for Khadas Edge-Captain.
Khadas Captain is the carrier board for Khadas Edge.
Specification
- Rockchip RK3399
- Dual-Channel 2GB/4GB LPDDR4
- SD card slot
- Onboard 16GB/32GB/128GB eMMC
- RTL8211FD 1Gbps
- AP6356S/AP6398S WiFI/BT
- HDMI Out, DP, MIPI DSI/CSI, eDP
- USB 3.0, 2.0
- USB Type C power and data
- GPIO expansion ports
- Full 4 Lane M.2 Socket
- 16MB SPI Flash
- IR
- Programmable MCU
Commit details of rk3399-khadas-edge-*.dts sync from Linux 5.3-rc2:
"arm64: dts: rockchip: Add support for Khadas Edge/Edge-V/Captain boards"
(sha1: c2aacceedc86af87428d998e23a1aca24fd8aa2e)
Signed-off-by: Nick Xie <nick@khadas.com>
Tested-by: Chris Webb <chris@arachsys.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add devicetree support for Khadas Edge-V.
Khadas Edge-V is a Khadas VIM form factor Rockchip RK3399 board.
Specification
- Rockchip RK3399
- Dual-Channel 2GB/4GB LPDDR4
- SD card slot
- Onboard 16GB/32GB/128GB eMMC
- RTL8211FD 1Gbps
- AP6356S/AP6398S WiFI/BT
- HDMI Out, DP, MIPI DSI/CSI, eDP
- USB 3.0, 2.0
- USB Type C power and data
- GPIO expansion ports
- Full 4 Lane M.2 Socket
- 16MB SPI Flash
- IR
- Programmable MCU
Commit details of rk3399-khadas-edge-*.dts sync from Linux 5.3-rc2:
"arm64: dts: rockchip: Add support for Khadas Edge/Edge-V/Captain boards"
(sha1: c2aacceedc86af87428d998e23a1aca24fd8aa2e)
Signed-off-by: Nick Xie <nick@khadas.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add devicetree support for Khadas Edge.
Khadas Edge is an expandable Rockchip RK3399 board with goldfinger.
Specification
- Rockchip RK3399
- Dual-Channel 2GB/4GB LPDDR4
- Onboard 16GB/32GB/128GB eMMC
- RTL8211FD 1Gbps
- AP6356S/AP6398S WiFI/BT
- HDMI Out, DP
- USB 3.0, 2.0
- USB Type C power and data
- 16MB SPI Flash
- Programmable MCU
Commit details of rk3399-khadas-edge-*.dts sync from Linux 5.3-rc2:
"arm64: dts: rockchip: Add support for Khadas Edge/Edge-V/Captain boards"
(sha1: c2aacceedc86af87428d998e23a1aca24fd8aa2e)
Signed-off-by: Nick Xie <nick@khadas.com>
Tested-by: Chris Webb <chris@arachsys.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
DMA for MMCs can be enabled, since the previous patch fixes
the following issue in SPL:
Trying to boot from MMC1
spl: mmc init failed with error: -110
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###
Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Set DDR as non-secure so that MMC DMA can access.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
[cherry picked from bfe741ab9e and 73d952acc8 with minor modifications]
Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The BCM2835/2836 watchdog is not used in mainline U-Boot at all. This
patch removes the driver and its references (CONFIG_BCM2835_WDT)
completely.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Paolo Pisati <p.pisati@gmail.com>
- add support for 4GiB DRAM memory
- add support for Amlogic G12B based Odroid-N2
- small duplicate logic fix for gxbb clock driver
-----BEGIN PGP SIGNATURE-----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=Q5fc
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20190731' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic
- sync Amlogic G12A DT with linux 5.3-rc1
- add support for 4GiB DRAM memory
- add support for Amlogic G12B based Odroid-N2
- small duplicate logic fix for gxbb clock driver
In attempts to speed up SPL and reduce size, the MDIO pin muxing
was inadvertently affected. Since the ethernet driver will setup
the pin muxing when ethernet is loaded, this patch will also
pinmux the MDIO pins at the same time. Once an DM compatible
MDIO driver is available, this can be removed.
Fixes: 877ab2423b ("ARM: davinci: da850: Manual pinmux only
when PINCTRL not available")
Signed-off-by: Adam Ford <aford173@gmail.com>
The commit 355be915ed ("arm: dts: k3-am654: Update power-domains
property for each node") has updated the power-domain cells value
and updated power-domains property in various existing dts nodes but
missed updating the cpsw_nuss node. This results in the following
build warning, fix this.
arch/arm/dts/k3-am654-base-board.dtb: Warning (power_domains_property): /interconnect@100000/interconnect@28380000/cpsw_nuss@046000000:power-domains: property size (8) too small for cell size 2
arch/arm/dts/k3-am654-r5-base-board.dtb: Warning (power_domains_property): /interconnect@100000/interconnect@28380000/cpsw_nuss@046000000:power-domains: property size (8) too small for cell size 2
Fixes: 355be915ed ("arm: dts: k3-am654: Update power-domains property for each node")
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
"fastboot flashall" expects "fastboot getvar product" value to be one of
values provided in android-info.txt file (in AOSP), from "require
board=" list. Before this patch, "am57xx" is returned for all AM57xx
based boards, as it's set in $board env var from SYS_BOARD in
board/ti/am57xx/Kconfig file, which is used for default implementation
of "fastboot getvar product".
In order to fix that inconsistency, let's do next:
1. In U-Boot: override fastboot.product, reusing the value from
$board_name
2. In AOSP: provide values for all AM57xx boards we can use to
device/ti/beagle_x15/board-info.txt file
This way requirements check in "fastboot flashall" will work as
expected, verifying that user tries to flash images to the board which
those images were built for.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Acked-by: Andrew F. Davis <afd@ti.com>
When configured with 4GiB DRAM size, only 3.8GiB is available, the
I/O beeing mapped in the last 256MiB of the first 4GiB physical memory/
First fixup the mm_region to handle the first 3.8GiB as memory and the
last 256MiB as I/O.
Then limit the real memory reported by the firmware to the available
physical space, 3.8GiB aligned with the mm_region memory zone size.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Mark Kettenis <kettenis@openbsd.org>
Import HardKernel Odroid-N2 DT from Linux 5.3-rc1, commit 5f9e832c1370
("Linus 5.3-rc1") based on an Amlogic G12B S922X SoC.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Mark Kettenis <kettenis@openbsd.org>
Sync the Amlogic Meson G12A DT and Bindings file with the Linux 5.3-rc1
from the commit 5f9e832c1370 ("Linus 5.3-rc1").
Also remove the meson-g12a-u-boot.dtsi and meson-g12a-u200-u-boot.dtsi,
now conflicting with the main DT content.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Mark Kettenis <kettenis@openbsd.org>
fpga:
- Xilinx virtex2 cleanup
- Altera cyclon2 cleanup
zynq:
- Minor Kconfig cleanup
- Add psu_init configuration for Z-turn board
zynqmp:
- Add support for pmufw config passing to PMU
- script for psu_init conversion
- zcu1275 renaming
xilinx:
- Add support for UltraZed-EV SoM
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCXUBgGwAKCRDKSWXLKUoM
IcJJAKCUoHRpqNgcZUiE10D9/VhZ3bUVtwCgi0fzSlqgHVG2EzApfqN+2KfrGJo=
=7i0K
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2019.10' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx/FPGA changes for v2019.10
fpga:
- Xilinx virtex2 cleanup
- Altera cyclon2 cleanup
zynq:
- Minor Kconfig cleanup
- Add psu_init configuration for Z-turn board
zynqmp:
- Add support for pmufw config passing to PMU
- script for psu_init conversion
- zcu1275 renaming
xilinx:
- Add support for UltraZed-EV SoM
Avnet UltraZed-EV Starter Kit is composed by the UltraZed-EV SoM and the
only publicly-available compatible carrier card. The SoM is based on the EV
version of the Xilinx ZynqMP SoC+FPGA.
The psu_init_gpl.c file has been generated from the board definition files
at [0] using Vivado 2018.3 and then minimized by
tools/zynqmp_psu_init_minimize.sh. Manually removed serdes init code since
it is not mentioned in device tree and fixed a checkpatch error.
[0] 3686c9ff7d/ultrazed_7ev_cc/1.1
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Optionally allow U-Boot to load a configuration object into the Power
Management Unit (PMU) firmware on Xilinx ZynqMP.
The configuration object is required by the PMU FW to enable most SoC
peripherals. So far the only way to boot using U-Boot SPL was to hard-code
the configuration object in the PMU firmware. Allow a different boot
process, where the PMU FW is equal for any ZynqMP chip and its
configuration is passed at runtime by U-Boot SPL.
All the code for Inter-processor communication with the PMU is isolated in
a new file (pmu_ipc.c). The code is inspired by the same feature as
implemented in the Xilinx First Stage Bootloader (FSBL) and Arm Trusted
Firmware:
* fb647e6b4c/lib/sw_apps/zynqmp_fsbl/src/xfsbl_misc_drivers.c (L295)
* c48d02bade/plat/xilinx/zynqmp/pm_service/pm_api_sys.c (L357)
SPL logs on the console before loading the configuration object:
U-Boot SPL 2019.07-rc1-00511-gaec224515c87 (May 15 2019 - 08:43:41 +0200)
Loading PMUFW cfg obj (2008 bytes)
EL Level: EL3
...
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Name of this platform has changed and released to customers that's why
name has also changed.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Series-to: uboot
When an image is signed/encrypted on K2 devices the image may get padded
to meet alignment requirements for the signature/encryption type. The
original size is appended as 4 bytes little-endian to the end of the
final image.
Normally the trailing extra bytes are ignored and so restoring the
exact original size is not important. In the case of initrd the
original size is important as the kernel uses it to look for
additional filesystem data and can do the wrong thing when the
size is not correct.
Read off the original size and report it back from the image post
processing stage.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Enable the driver-model on da850-evm. We need to add a dummy nand node
to the device tree, as the real nand node is a sub-node of the aemif
device.
On linux the aemif driver populates all its child nodes, but we can't do
it in u-boot currently.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Tested-by: Adam Ford <aford173@gmail.com> #da850-evm
Enable the driver-model on da850-lcdk. We need to add a dummy nand node
to the device tree, as the real nand node is a sub-node of the aemif
device.
On linux the aemif driver populates all its child nodes, but we can't do
it in u-boot currently.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The pumpkin board is made by Gossamer Engineering and is using
a MediaTek SoC. The board currently comes in two available version:
MT8516 SoC and MT8167 SoC.
The board provides the following IOs: eMMC, NAND, SD card, USB type-A,
Ethernet, Wi-Fi, Bluetooth, Audio (jack out, 2 PDM port, 1 analog in),
serial over USB, and an expansion header.
Additionally there is a HDMI port, DSI port, and camera port only
on the MT8167 version of the board.
The board can be powered by battery and/or via a USB Type-C port and
is using a PMIC MT6392.
The eMMC and NAND are sharing pins and cannot be used together.
This commit is adding the basic boot support for the Pumpkin MT8516
board on the eMMC.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
- Clean up and migrate to use common rockchip spl board file
- Clean up and migrate to use common rockchip board file
- Increase rk3288 CONFIG_SYS_BOOTM_LEN to 16MB
Use common board file for board_init() and board_late_init(),
for Rockchip SoCs have very similar process.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Use common board file for board_init() and board_late_init(),
for Rockchip SoCs have very similar process.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Use common board file for board_init() and board_late_init(),
for Rockchip SoCs have very similar process.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Use common board file for board_init() and board_late_init(),
for Rockchip SoCs have very similar process.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Use common board file for board_init() and board_late_init(),
for Rockchip SoCs have very similar process.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The rk3288_detect_reset_reason() is per-SoC operation, move
it to rk3288.c, and extend the rk_board_late_init() with
rk3288_board_late_init() to make all the board works fine
as before.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The veyron_init() should go to its board file veyron.c,
and the board_early_init_f() could be the right place.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Use common board file for board_init() and board_late_init(),
for Rockchip SoCs have very similar process.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Use common board file for board_init() and board_late_init(),
for Rockchip SoCs have very similar process.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Use common board file for board_init() and board_late_init(),
for Rockchip SoCs have very similar process.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Use common board file for board_init() and board_late_init(),
for Rockchip SoCs have very similar process.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Add common board file for Rockchip SoCs to avoid too much
copy-paste work for different SoCs.
This board file in charge for common board_init() and board_late_init()
in U-Boot proper.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Use "snps,dwc2" for compatible name and and common variable
names so that we can share the common code for all SoCs.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The fastboot_set_reboot_flag() update a TAG into a register
for next boot, use the common macro for the register so that
we can re-use the function for different SoCs.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
rk3399 has similar boot flow in SPL with other Rockchip SoCs,
migrate to use common spl board file.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Add a board_early_init_f() in board_init_f() and move the board
specific init code into its own board file.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Move boot_devices definition into rk3399.c, so that we can
share the common code for board_spl_was_booted_from().
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
rk3368 has similar boot flow in SPL with other Rockchip SoCs,
migrate to use common spl board file.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
rk3328 has similar boot flow in SPL with other Rockchip SoCs,
migrate to use common spl board file.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
"u-boot,spl-boot-order" is more flexible and other rockchip SoCs
has convert to use it, migrate to use the new dts property.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
We are using "u-boot,spl-boot-order" now and re-use the
definition from rk3288-u-boot.dtsi, so remove it directly here.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
rk3288 has similar boot flow in SPL with other Rockchip SoCs,
migrate to use common spl board file.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Only firefly-rk3288 has the dts node "u-boot,boot-led",
while CONFIG_SPL_LED is not enable, move code to firefly-rk3288
now in case someone need this code.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Update to fix warning:
u-boot.itb.tmp: Warning (unit_address_vs_reg): Node /images/uboot@1
has a unit name, but no reg property
u-boot.itb.tmp: Warning (unit_address_vs_reg): Node /images/optee@1
has a unit name, but no reg property
u-boot.itb.tmp: Warning (unit_address_vs_reg): Node /images/fdt@1
has a unit name, but no reg property
u-boot.itb.tmp: Warning (unit_address_vs_reg): Node /configurations/conf@1
has a unit name, but no reg property
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
rk322x has similar boot flow in SPL with other Rockchip SoCs,
migrate to use common spl board file.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
rk3188 has similar boot flow in SPL with other Rockchip SoCs,
migrate to use common spl board file.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
SPL bootrom support is a boot device just like mmc and etc,
use formal boot device instead of jump to bootrom directly.
Enable the Kconfig by default if ROCKCHIP_BACK_TO_BROM is enabled.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Init CPU frquency in clock driver instead of in SPL board file,
this will help for use common board file later.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The common spl board file handles board_init_f() in SPL,
and with board_early_init_f() and arch_cpu_init() callback,
other operateion after board_init_f() should go to board specific
spl_board_init().
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Provide proper display timings for lcdif node, used by mxsfb DM_VIDEO
enabled framebuffer driver.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
1. This fixes linking issues when building with DM_VIDEO enabled mxsfb
driver.
2. Provide proper defines for both VIDEO=y and DM_VIDEO=y.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Fix lcdif DT node and make it conform to the structure defined in the
Linux devicetree bindings [1]. Currently there is support only for
old style lcdif node definitions.
[1] https://www.kernel.org/doc/Documentation/devicetree/bindings/display/mxsfb.txt
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Add dumb node for NXP Display Control Unit0(DCU), which permits DM_ENABLED
converted driver to be probed. Currently no display timings are provided
in this node.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Like the other Logic PD OMAP35/DM37 boards, this board has device
tree enabled for U-Boot. This patch converts the board to enable
SPL_OF_CONTROL and further shrinks the device tree in SPL to limit
it to UART3 (console), MMC1, i2c1, and GPIO4 (for mmc1 CD and WP).
There appears to be a bug in minicom so users may need to
switch the minicom terminal emulation to ANSI from VT102 due
to the junk that gets pushed out of the UART on startup.
Signed-off-by: Adam Ford <aford173@gmail.com>
Update the MMC2_HS200_MANUAL1 iodelay values to match with the latest
dra76x data manual[1].
Also this particular pinctrl-array is using spaces instead of tabs for
spacing between the values and the comments. Fix this as well.
[1] http://www.ti.com/lit/ds/symlink/dra76p.pdf
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
If UHS speed modes are enabled, a compatible SD card switches down to 1.8V
during enumeration. If after this a software reboot/crash takes place and
on-chip ROM tries to enumerate the SD card, the difference in
IO voltages (host @ 3.3V and card @ 1.8V) may end up damaging the card.
The fix for this is to have support for power cycling the card in
hardware (with a PORz/soft-reset line causing a power cycle of the card).
Because the beaglebone X15 (rev A,B and C), am57xx-evms and am57xx-idks don't
have this capability, disable voltage switching for these boards.
The major effect of this is that the maximum supported speed mode is now
high speed(50 MHz) down from SDR104(200 MHz).
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Sync with kernel dts by adding pinmuxes for mmc1 and mmc2. This fixes an
issue where mmc2 (eMMC) was coming up in HS52 mode instead of the
highest DDR52 mode.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
During a short period when the bus voltage is switched from 3.3v to 1.8v,
(to enumerate UHS mode), the mmc module is disabled and the mmc IO lines
are kept in a state according to the programmed pad mux pull type.
According to 4.2.4.2 Timing to Switch Signal Voltage in "SD Specifications
Part 1 Physical Layer Specification Version 5.00 February 22, 2016", the
host should hold CLK low for at least 5ms.
In order to keep the card line low during voltage switch, the pad mux of
mmc1_clk line should be configured to pull down.
Add a new pinctrl group for clock line without pullup to be used in boards
where mmc1_clk line is not connected to an external pullup.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Common Processor board is the baseboard that has most of the actual connectors,
power supply etc. A SOM (System on Module) is plugged on to the common
processor board and this contains the SoC, PMIC, DDR and basic highspeed
components necessary for functionality. Add initial dt support for this
common processor board.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The A72 U-Boot code loads and boots a number of remote processors
including the C71x DSP, both the C66_0 and C66_1 DSPs, and the various
Main R5FSS Cores. Change the memory attributes for the DDR regions used
by the remote processors so that the cores can see and execute the
proper code.
A separate table based on the current AM65x table is added for J721E SoCs,
since the number of remote processors and their DDR usage will be different
between the two SoC families.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Use the System Firmware (SYSFW) loader framework to load and start
the SYSFW as part of the J721E early initialization sequence. While
at it also initialize the MCU_UART0 pinmux as it is used by SYSFW
to print diagnostic messages.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Populate the release_resources_for_core_shutdown() api with
shutting down r5 cores so that it will by called just after
jumping to ATF.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Obtain the boot index as left behind by the device boot ROM and store
it in scratch pad SRAM for later use before it may get overwritten.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
To access various control MMR functionality the registers need to
be unlocked. Do that for all control MMR regions in the MCU and MAIN
domains. We may want to go back later and limit the unlocking that's
being done.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
J721E allows for booting from primary or backup boot media.
Both media can be chosen individually based on switch settings.
ROM looks for a valid image in primary boot media, if not found
then looks in backup boot media. In order to pass this boot media
information to boot loader, ROM stores a value at a particular
address. Add support for reading this information and determining
the boot media correctly.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
The J721E SoC belongs to the K3 Multicore SoC architecture platform,
providing advanced system integration to enable lower system costs
of automotive applications such as infotainment, cluster, premium
Audio, Gateway, industrial and a range of broad market applications.
This SoC is designed around reducing the system cost by eliminating
the need of an external system MCU and is targeted towards ASIL-B/C
certification/requirements in addition to allowing complex software
and system use-cases.
Some highlights of this SoC are:
* Dual Cortex-A72s in a single cluster, three clusters of lockstep
capable dual Cortex-R5F MCUs, Deep-learning Matrix Multiply Accelerator(MMA),
C7x floating point Vector DSP, Two C66x floating point DSPs.
* 3D GPU PowerVR Rogue 8XE GE8430
* Vision Processing Accelerator (VPAC) with image signal processor and Depth
and Motion Processing Accelerator (DMPAC)
* Two Gigabit Industrial Communication Subsystems (ICSSG), each with dual
PRUs and dual RTUs
* Two CSI2.0 4L RX plus one CSI2.0 4L TX, one eDP/DP, One DSI Tx, and
up to two DPI interfaces.
* Integrated Ethernet switch supporting up to a total of 8 external ports in
addition to legacy Ethernet switch of up to 2 ports.
* System MMU (SMMU) Version 3.0 and advanced virtualisation
capabilities.
* Upto 4 PCIe-GEN3 controllers, 2 USB3.0 Dual-role device subsystems,
16 MCANs, 12 McASP, eMMC and SD, UFS, OSPI/HyperBus memory controller, QSPI,
I3C and I2C, eCAP/eQEP, eHRPWM, MLB among other peripherals.
* Two hardware accelerator block containing AES/DES/SHA/MD5 called SA2UL
management.
* Configurable L3 Cache and IO-coherent architecture with high data throughput
capable distributed DMA architecture under NAVSS
* Centralized System Controller for Security, Power, and Resource
Management (DMSC)
See J721E Technical Reference Manual (SPRUIL1, May 2019)
for further details: http://www.ti.com/lit/pdf/spruil1
Add base support for J721E SoC
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Update the power-domain-cells to 2 and add the permissions
to each node. Mark the following nodes accessed by r5 as shared:
- DDR node
- main uart 0
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Rather than simply parking the R5 core in WFE after starting up ATF
on A53 instead use SYSFW API to properly shut down the R5 CPU cores
as well as associated timer resources that were pre-allocated. This
allows software further downstream to properly and gracefully bring
the R5 cores back online if desired.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
boot_devices may defined in soc file, and used in board file,
we need to delear it in header file.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The boot source from BootRom is store at a fix offset of IRAM,
update to use the common macro instead of rk3399 specific one.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Now that we removed all legacy boards selecting TI_EMAC we can
completely convert the driver code to using the driver model.
This patch also updates all remaining users of davinci_emac.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Tested-by: Adam Ford <aford173@gmail.com> #am3517-evm & da850-evm
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The LS1021A-TSN is a development board built by VVDN/Argonboards in
partnership with NXP.
It features the LS1021A SoC and the first-generation SJA1105T Ethernet
switch for prototyping implementations of a subset of IEEE 802.1 TSN
standards.
Supported boot media: microSD card (via SPL), QSPI flash.
Rev. A of the board uses a Spansion S25FL512S_256K serial flash, which
is 64 MB in size and has an erase sector size of 256KB (therefore,
flashing the RCW would erase part of U-Boot).
Rev. B and C of the board use a Spansion S25FL256S1 serial flash, which
is only 32 MB in size but has an erase sector size of 64KB (therefore
the RCW image can be flashed without erasing U-Boot).
To avoid the problems above, the U-Boot base address has been selected
at 0x100000 (the start of the 5th 256KB erase sector), which works for
all board revisions. Actually 0x40000 would have been enough, but
0x100000 is common for all Layerscape devices.
eTSEC3 is connecting directly to SJA1105 via an RGMII fixed-link, but
SJA1105 is currently not supported by uboot. Therefore, eTSEC3 is
disabled.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Jianchao Wang <jianchao.wang@nxp.com>
Signed-off-by: Changming Huang <jerry.huang@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
[Vladimir] Code taken from https://github.com/openil/u-boot (which
itself is mostly copied from ls1021a-iot) and adapted with the following
changes:
- Add a008850 errata workaround
- Converted eTSEC, MMC to DM to avoid all build warnings
- Plugged in distro boot feature, including support for extlinux.conf
- Added defconfig for QSPI boot
- Added the board/freescale/ls1021atsn/README.rst for initial setup
- Increased CONFIG_SYS_MONITOR_LEN so that the SPL malloc pool does not
get overwritten during copying of the u-boot.bin payload from MMC to
DDR.
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Now that we have added driver model support to the TSEC driver,
convert ls1021atwr board to use it.
This depends on previous DM series for ls1021atwr:
http://patchwork.ozlabs.org/patch/561855/
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
[Vladimir] Made the following changes:
- Added 'status = "disabled";' for all Ethernet ports in ls1021a.dtsi
- Fixed the confusion between the SGMII/TBI PCS for enet0 and enet1 -
a mistake ported over from Linux. Each SGMII PCS lies on the private
MDIO bus of the interface (and the RGMII enet2 has no SGMII PCS).
- Added CONFIG_DM_ETH to all ls1021atwr_* defconfigs
- Completely removed non-DM_ETH support from ls1021atwr
- Changed "compatible" string from "fsl,tsec-mdio" to "fsl,etsec2-mdio"
and from "fsl,tsec" to "fsl,etsec2" to match Linux
This patch solves the following warnings:
arch/arm/mach-stm32mp/psci.c:
warning: no previous prototype for ‘psci_set_state’ [-Wmissing-prototypes]
warning: no previous prototype for ‘psci_arch_cpu_entry’ [-Wmissing-prototypes]
warning: no previous prototype for ‘psci_features’ [-Wmissing-prototypes]
warning: no previous prototype for ‘psci_version’ [-Wmissing-prototypes]
warning: no previous prototype for ‘psci_affinity_info’ [-Wmissing-prototypes]
warning: no previous prototype for ‘psci_migrate_info_type’ [-Wmissing-prototypes]
warning: no previous prototype for ‘psci_cpu_on’ [-Wmissing-prototypes]
warning: no previous prototype for ‘psci_cpu_off’ [-Wmissing-prototypes]
warning: no previous prototype for ‘psci_system_reset’ [-Wmissing-prototypes]
warning: no previous prototype for ‘psci_system_off’ [-Wmissing-prototypes]
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
* Implement the EVT_SIGNAL_VIRTUAL_ADDRESS_CHANGE event.
* Address errors of type -Werror=address-of-packed-member when building
with GCC9.1
* Fix an error when adding memory add addres 0x00000000.
* Rework some code comments for Sphinx compliance.
-----BEGIN PGP SIGNATURE-----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=aj4j
-----END PGP SIGNATURE-----
Merge tag 'efi-2019-10-rc1-2' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for v2019.10-rc1 (2)
* Implement the EVT_SIGNAL_VIRTUAL_ADDRESS_CHANGE event.
* Address errors of type -Werror=address-of-packed-member when building
with GCC9.1
* Fix an error when adding memory add addres 0x00000000.
* Rework some code comments for Sphinx compliance.
Update "dma-ranges" DT property of all PCIe controllers in the system
with the up-to-date DRAM layout. This allows the PCIe controller take
full advantage of all the available DRAM.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The generic code in common/spl/spl.c allows TPL/SPL banners to be
silenced by unsetting CONFIG_TPL_BANNER_PRINT or CONFIG_SPL_BANNER_PRINT
respectively. However, arch/arm/mach-rockchip/tpl.c prints this banner
unconditionally.
Fix the rockchip-specific tpl.c so that the TPL banner depends on
CONFIG_TPL_BANNER_PRINT in the same way as the generic code.
Signed-off-by: <chris@arachsys.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
If CONFIG_DEBUG_UART is set but CONFIG_TPL_SERIAL_SUPPORT is not, the
serial output should be available in SPL and full U-Boot, but not built
in TPL. However, the rockchip tpl.c instead fails to compile with
undefined references to the debug UART.
Instead, initialise the debug UART and print the TPL banner only if both
CONFIG_DEBUG_UART and CONFIG_TPL_SERIAL_SUPPORT are set.
Signed-off-by: <chris@arachsys.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
For STM32 QSPI driver, "st,stm32-qspi" compatible string was first
introduced in U-boot. But later in kernel side, "st,stm32f469-qspi"
was used.
To simplify, align U-boot QSPI compatible string with kernel one.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
For STM32 QSPI driver, "st,stm32-qspi" compatible string was first
introduced in U-boot. But later in kernel side, "st,stm32f469-qspi"
was used.
To simplify, align U-boot QSPI compatible string with kernel one.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
This moves sysreset support for socfgpa from ad-hoc code in mach-socfpga
to a UCLASS_SYSRESET based dm driver.
A side effect is that gen5 and a10 can now select between cold and warm
reset.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
This adds a define for the bit in rstmgr's ctrl regiser that issues
a cold reset (we had a define for the warm reset bit only) in preparation
for a proper sysrese driver.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Series changes: 2
- separate this patch to the register descriptions from the actual
sysreset driver patch
make_fit_aft.py depends on the non-standard library pyelftools to pull
out PT_LOAD segments from ELF files. However, this is as easy to do
manually, without imposing the extra dependency on users.
Structures in the ELF file are unpacked into variables named to exactly
match the ELF spec to ensure the destructuring code is reasonably
self-documenting.
Signed-off-by: Chris Webb <chris@arachsys.com>
Reviewed-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
SPL/TPL share the same secure_timer_init(), update to use
one copy source code and update to use CONFIG_ROCKCHIP_STIMER_BASE
as base address and rename to function name to rockchip_stimer_init().
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Rockchip SoCs have similar boot process, prefer to use TPL for DRAM
init and back to bootrom, and SPL as Trust ATF/U-Boot loader. TPL
common board is a basic TPL board init which can be shared for most
of SoCs to avoid copy-pase for different SoCs.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The SoC related init will move to SPL and keep TPL clean,
so that we can reuse the common TPL board file.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
We have convert all SoC to use DM timer or ARM arch/generic
timer, we can remove this rk_timer now.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
We prefer to use ARM arch timer instead of rockchip timer, so that
we are using the same timer for SPL, U-Boot and Kernel, which will
make things simple and easy to track to boot time.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
We prefer to use ARM arch timer instead of rockchip timer, so that
we are using the same timer for SPL, U-Boot and Kernel, which will
make things simple and easy to track to boot time.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
We prefer to use ARM arch timer instead of rockchip timer, so that
we are using the same timer for SPL, U-Boot and Kernel, which will
make things simple and easy to track the boot time.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
We prefer to use ARM arch timer instead of rockchip timer, so that
we are using the same timer for SPL, U-Boot and Kernel, which will
make things simple and easy to track to boot time.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
We share the same default SPL boot order for all rk3288 boards,
use dts instead of hard code in board file.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The fdt interfaces are actuall depends on OF_LIBFDT instead
of OF_CONTROL, some boards may enable OF_CONTROL while disable
OF_LIBFDT.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The rk3288-firefly board have different setting for sdmmc
io, sync then from kernel mainline:
6fbc7275c7a9 Linux 5.2-rc7
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Add arch_cpu_init() in SPL for soc related init, and
move configure_l2ctlr() into it.
The arch_cpu_init() only need to run once, so no need
to run in TPL.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
We needs SPL LIBCOMMON and LIBGENERIC for all boards,
so we can enable them by default and no need to define
in each board.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
We needs SPL LIBCOMMON and LIBGENERIC for all boards,
so we can enable them by default and no need to define
in each board.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
We needs SPL LIBCOMMON and LIBGENERIC for all boards,
so we can enable them by default and no need to define
in each board.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
We needs SPL LIBCOMMON and LIBGENERIC for all boards,
so we can enable them by default and no need to define
in each board.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Rockchip SoCs have different ROCKCHIP_BOOT_MODE_REG value,
move it to SoC's own Kconfig, and add address for rk3128 and
rk3328 so that all SoCs have available address.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Each SoC have its config setting and its Kconfig, move
the specific setting to its own Kconfig file.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Each SoC have its config setting and its Kconfig, move
the specific setting to its own Kconfig file.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Each SoC have its config setting and its Kconfig, move
the specific setting to its own Kconfig file.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Each SoC have its config setting and its Kconfig, move
the specific setting to its own Kconfig file.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Use LPDDR4-100 sdram timings dtsi for RockPI-4 board.
All these timings are processed during TPL stage of rock-pi-4 board,
bootchain. This make TPL would replace rockchip in house rkbin in
current bootchain.
Bootchain after and before this change:
TPL -> SPL -> U-Boot proper
rkbin -> SPL -> U-Boot proper
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Use DDR3-1866 2GB ddr timings dtsi for 1GB NanoPi Neo4 board.
Since sdram rk3399 support dynamic stride and rank detection it
can able to detect 1GB ddr eventough the timings are meant for
dual channel, 2GB size.
Bootchain after and before this change are:
TPL -> SPL -> U-Boot proper
rkbin -> SPL -> U-Boot proper
This certainly fix the second channel data training initialization
since we have dynamic rank, stride where second channel capabilities
are clear or memset to 0.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Use LPDDR4-100 sdram timings dtsi for Rockpro64 board.
All these timings are processed during TPL stage of rockpro64 board,
bootchain. This make TPL would replace rockchip in house rkbin in
current bootchain.
Bootchain after and before this change:
TPL -> SPL -> U-Boot proper
rkbin -> SPL -> U-Boot proper
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Add sdram timings for LPDDR4-100 via rk3399-sdram-lpddr4-100.dtsi file.
all timings are dumped from rkbin/bin/rk33/rk3399_ddr_800MHz_v1.20.bin
Associated LPDDR4 board -u-boot.dtsi can include this to make these
timings available during SPL or TPL stages.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Add u-boot,dm-pre-reloc property for pmu in rk3399-u-boot.dtsi
so-that SPL can access pmu.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Add pmu compatible with relevant U_BOOT_DRIVER for rk3399
via syscon rk3399 driver.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Add pmu header file for rk3399 SoC, this will help
to configure pmu in sdram driver.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Add DdrMode structure with associated bit fields.
These would help to reconfigure sdram capabilities during
lpddr4 setup related configs.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Add DdrTimingC0 structure with associated bit fields.
These would help to reconfigure sdram capabilities during
lpddr4 setup related configs.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Add dram config macro for handling ddr version number.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
cs0_row, cs1_row and cs1_col needs more bits to show its
correct value, update to make use of both sys_reg2,
sys_reg3.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
(Squash similar patches into one patch)
Signed-off-by: Kever Yang <Kever.yang@rock-chips.com>
Add simplified and meaningful macro for all setting.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
(Squash the similar patches into 1 patch)
Signed-off-by: Kever Yang <Kever.yang@rock-chips.com>
For a single binary approach for imx6 quad/dual/duallite/solo it
is necessary to enable CONFIG_SATA for quad/dual. On the other hand
on imx6 duallite/sole SATA is not available.
Therefore sata_remove() is skipped according to a blacklist scheme.
Adding further imx derivates is probably not recessary as they are
usually not pin-compatible and therefore a different board with its
own configuration.
Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.com>
According to iMX6DQ RM, the minor field (low 8 bits) in DIGPROG is not
aligned on silicon revision 1.3. So update get_cpu_rev to correct the
revision.
0x00630002 Silicon revision 1.2
0x00630005 Silicon revision 1.3
0x00630006 Silicon revision 1.6
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
This device tree adds support for DHCOM iMX6 duallite and solo
deriviates.
Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.com>
Reviewed-by: Marek Vasut <marex@denx.de>
To use the device tree definitions imx6q-dhcom-som.dtsi for all imx6 derivatives rename
it to imx6qdl-dhcom.dtsi. We omit the '-som', because it simplifies further mainlinening
of already existing device trees.
To reuse board level common stuff imx6qdl-dhcom-pdk2.dtsi is created and included by
imx6q-dhcom-pdk2.dts.
Signed-off-by Ludwig Zenz <lzenz@dh-electronics.com>
Reviewed-by: Marek Vasut <marex@denx.de>
The gpio command currently uses equal bank names "GPIO0_"
for all existing gpio banks, i. e.:
U-Boot# gpio status -a
Bank GPIO0_:
GPIO0_0: input: 0 [ ]
GPIO0_1: output: 1 [x] dbg1.gpios
...
Bank GPIO0_:
GPIO0_0: input: 0 [ ]
GPIO0_1: input: 0 [ ]
...
So the command is broken, it is not possible to address
a desired bank. Add gpio aliases to fix this.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
New imx8 boards started adding duplicated UART init code.
Factor out this to common function sc_pm_setup_uart().
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
This file setups UART5 based serial to be used as pre-relocation
console in the U-Boot proper.
On purpose pinux configuration is omitted here as it has been already
done in SPL. For early pre-relocation code we only need the serial
device from DTS.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
This commit ports from Linux kernel - tag: v5.1 - the device tree
description for display5 board.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Those properties are U-Boot specific as the mxs gpio Linux driver (up to
version v5.1.11) is not supporting them.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This patch copies from the Linux kernel stable (tag v5.1.11)
SHA1: 17bb763e7eaf i.MX28 related device tree files.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Currently, when the spl_boot_device checks the boot device, it
will only return MMC1 when it's either sd or eMMC regardless
of whether or not it's MMC1 or MMC2. This is a problem when
booting from MMC2 if MMC isn't being manually configured like in
the DM_SPL case with SPL_OF_CONTROL.
This patch will check the register and return either MMC1 or MMC2.
Signed-off-by: Adam Ford <aford173@gmail.com>
Writing/updating boot image in nand device is not
straight forward in i.MX6 platform and it requires
boot control block(BCB) to be configured.
It becomes difficult to use uboot 'nand' command to
write BCB since it requires platform specific attributes
need to be taken care of.
It is even difficult to use existing msx-nand.c driver by
incorporating BCB attributes like mxs_dma_desc does
because it requires change in mtd and nand command.
So, cmd_nandbcb implemented in arch/arm/mach-imx
BCB contains two data structures, Firmware Configuration Block(FCB)
and Discovered Bad Block Table(DBBT). FCB has nand timings,
DBBT search area, page address of firmware.
On summary, nandbcb update will
- erase the entire partition
- create BCB by creating 2 FCB/DBBT block followed by
1 FW block based on partition size and erasesize.
- fill FCB/DBBT structures
- write FW/SPL on FW1
- write FCB/DBBT in first 2 blocks
for nand boot, up on reset bootrom look for FCB structure in
first block's if FCB found the nand timings are loaded for
further reads. once FCB read done, DTTB will load and finally
firmware will be loaded which is boot image.
Refer section "NAND Boot" from doc/imx/common/imx6.txt for more usage
information.
Reviewed-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Sergey Kubushyn <ksi@koi8.net>
Signed-off-by: Shyam Saini <shyam.saini@amarulasolutions.com>
Add code to print the channel stride, this would help to
print the stride of associated channel.
Here is sample print on LPDDR4, 50MHz.
256B stride
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Add sdram ddr info print support, this would help to
observe the sdram base parameters.
Here is sample print on LPDDR4, 50MHz channel 0
BW=32 Col=10 Bk=8 CS0 Row=15 CS1 Row=15 CS=2 Die BW=16
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Add sdram driver to handle debug across rockchip SoCs.
This would help to improve code debugging feature for
sdram drivers in rockchip family, whoever wants to
debug the driver should call these core debug code on
their respective platform sdram drivers.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Add DDR4 enum number in common header.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
dramtype enum numbers as common across all dram controllers
in rockchip, so move the eneum values in common header.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Move common sdram structures like sdram_cap_info, sdram_base_params
into sdram_common header, this would help to reuse the same
from another controllers like px30.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Most of the ddr parameters are common in rk3399_base_params
structure and which would reuse it in another controller like
px30 in future.
So, rename the structure from rk3399_base_params into
sdram_base_params.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Group common ddr attributes like
- rank
- col
- bk
- bw
- dbw
- row_3_4
- cs0_row
- cs1_row
- ddrconfig
into a common cap_info structure for more code readability and extend
if possible based on the new features.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Let the board continue boot from the storage device where
it bootup.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
RK3399 use sdhci for eMMC and DW MMC for SD Card, and
spl will only try to boot from SDMMC if we don't specify
other boot device for spl-boot-order. So add sdhci and sdmmc
for spl-boot-order here.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync the dts files for the Rock960 boards from Linux to get the
latest changes and fixes for the devices.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
- Various FS/disk related fixes with security implications.
- Proper fix for the pci_ep test.
- Assorted bugfixes
- Some MediaTek updates.
- 'env erase' support.
The timer0 node has its two clocks written in reversed order. The timer0
is used as the tick timer which causes a problem that the time a delay
function used is 4 times longer.
This patch reverses these two clocks to solve this issue.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch sets CNTVOFF of ARM CP15 timer to zero to make sure the virtual
counter is fully usable for linux kernel.
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
If U-Boot is loaded and started from TF-A (you need to change
SYS_TEXT_BASE to 0x60000000), it will hang up at flash initialization.
If secure mode is off (default, or -machine virt,secure=off) at qemu,
it will provide dtb with two flash memory banks:
flash@0 {
bank-width = <0x4>;
reg = <0x0 0x0 0x0 0x4000000 0x0 0x4000000 0x0 0x4000000>;
compatible = "cfi-flash";
};
If secure mode is on, on the other hand, qemu provides dtb with 1 bank:
flash@0 {
bank-width = <0x4>;
reg = <0x0 0x4000000 0x0 0x4000000>;
compatible = "cfi-flash";
};
As a result, flash_init()/flash_get_size() will eventually fail.
With this patch applied, relevant CONFIG values are modified.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Currently, CONFIG_TFABOOT is located in armv8/fsl-layerscape Kconfig,
but it will be also useful for other targets if some additional
configuration are necessary.
So move it to arch/arm/Kconfig.
Please note that CONFIG_TFABOOT still depends on
CONFIG_ARCH_SUPPORT_TFABOOT and so the menu won't come up
if any target doesn't need its own customization for TF-A boot.
This will maintain the compatibility.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Sriram Dash <sriram.dash@nxp.com>
Cc: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Cc: Peng Ma <peng.ma@nxp.com>
Cc: Yuantian Tang <andy.tang@nxp.com>
Cc: Pankit Garg <pankit.garg@nxp.com>
When a crash occurs in thumb mode the crash dump is incorrect. This is due
to the usage of a non-existing configuration variable CONFIG_ARM_THUMB in
the definition of macro thumb_mode(regs).
Use CONFIG_IS_ENABLED(SYS_THUMB_BUILD) to detect that the code has been
compiled for thumb mode. Remove ARM_THUMB from config_whitelist.txt.
With the patch crash dumps indicate thumb mode correctly.
On a system with thumb mode:
=> exception unaligned
data abort
pc : [<8f7a2b52>] lr : [<8f7ab1ef>]
reloc pc : [<1780cb52>] lr : [<178151ef>]
sp : 8ed8c3f8 ip : 8f7a2b4d fp : 00000002
r10: 8f7f8228 r9 : 8ed95ea8 r8 : 8ed99488
r7 : 8f7ab141 r6 : 00000000 r5 : 8ed8c3f9 r4 : 8f7f6390
r3 : 8ed9948c r2 : 00000001 r1 : 00000000 r0 : 8f7f6390
Flags: nzCv IRQs off FIQs off Mode SVC_32 (T)
Code: 8f7e 466d f105 0501 (e9d5) 6700
The Flags line has '(T)' and in the Code line the output is in u16 groups.
On a system without thumb mode:
=> exception breakpoint
prefetch abort
pc : [<7ff5a5c8>] lr : [<7ff675ec>]
reloc pc : [<0000e5c8>] lr : [<0001b5ec>]
sp : 7ee0ad80 ip : 7ff5a5cc fp : 7ff674cc
r10: 00000002 r9 : 7ef0bed8 r8 : 7ffd6214
r7 : 7ef0e080 r6 : 00000000 r5 : 7ffd4090 r4 : 00000000
r3 : 7ef0e084 r2 : 00000001 r1 : 00000000 r0 : 7ffd4090
Flags: nzCv IRQs off FIQs off Mode SVC_32
Code: e1a0500d e2855001 e1c560d0 e3a00001 (e12fff1e)
The Flags line does not show '(T)' and in the Code line the output is in
u32 groups.
Reported-by: Marek Vasut <marex@denx.de>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
The TI AM654x EVM base board and the associated daughtercards have on-
board I2C-based EEPROMs containing board configuration data. Use the
board detection infrastructure introduced earlier to do the following:
1) Parse the AM654x EVM base board EEPROM and populate items like board
name and MAC addresses into the TI common EEPROM data structure
residing in SRAM scratch space
2) Check for presence of daughter card(s) by probing the associated
presence signals via an I2C-based GPIO expander. Then, if such a
card is found, parse the data such as additional Ethernet MAC
addresses from its on-board EEPROM and populate into U-Boot
accordingly
3) Dynamically create an U-Boot ENV variable called overlay_files
containing a list of daugherboard-specific DTB overlays based on
daughercards found.
This patch adds support for the AM654x base board ("AM6-COMPROCEVM")
as well as for the IDK ("AM6-IDKAPPEVM"), OLDI LCD ("OLDI-LCD1EVM")
PCIe/USB3.0 ("SER-PCIEUSBEVM"), 2 Lane PCIe/USB2.0 ("SER-PCIE2LEVM"),
and general purpuse ("AM6-GPAPPEVM") daughtercards.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
The board detection scheme employed on various TI EVMs makes use of
SRAM scratch space to share data read from an on-board EEPROM between
the different bootloading stages. Map the associated definition that's
used to locate this data into the SRAM scratch space we use on AM654x.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
The AM654 base board has a TCA9554/PCA9554-type GPIO expander on the
wkup_i2c0 bus at address 0x38 that is used to detect the presence of
daughter cards. Add a respective DTS description of this expander
to enable its use.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
To enable the use of an EEPROM-based board detection scheme we need to
be able to access the I2C bus associated with the EEPROMs across all
3 stages of U-Boot: R5 SPL, A53 SPL, and A53 U-Boot (proper). So go
ahead and add/update the wkup_i2c0 peripheral module DTS definitions
and its associated pinmux node accordingly.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Only U-Boot specifc DT properties or overrides, must be in -u-boot.dtsi.
Pinctrl nodes does not belong here. Now that pinctrl nodes are in kernel
DT, there is no reason to be keep these in -u-boot.dtsi. Move them to
proper places so that it would ease copying DT entries from kernel DT.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
There is no need for to include this header here, so drop it.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Use the System Firmware (SYSFW) loader framework to load and start
the SYSFW as part of the AM654 early initialization sequence. While
at it also initialize the WKUP_UART0 pinmux as it is used by SYSFW
to print diagnostic messages.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Introduce a framework that allows loading the System Firmware (SYSFW)
binary as well as the associated configuration data from an image tree
blob named "sysfw.itb" from an FS-based MMC boot media or from an MMC
RAW mode partition or sector.
To simplify the handling of and loading from the different boot media
we tap into the existing U-Boot SPL framework usually used for loading
U-Boot by building on an earlier commit that exposes some of that
functionality.
Note that this initial implementation only supports FS and RAW-based
eMMC/SD card boot.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
On some platform we have sufficient memory available early on to allow
setting up and using a basic BSS prior to entering board_init_f(). Doing
so can for example be used to carry state over to board_init_r() without
having to resort to extending U-Boot's global data structure.
To support such scenarios add a Kconfig option called CONFIG_SPL_EARLY_BSS
to allow moving the initialization of BSS prior to entering board_init_f(),
if enabled. Note that using this option usually should go along with using
CONFIG_SPL_SEPARATE_BSS and configuring BSS to be located in memory
actually available prior to board_init_f().
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
With changes in the driver requiring phy related properties,
add the same for the SD card node to prevent breaking boot with
the driver update.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Sync the sdhci0 node from kernel. This changes the compatible that is
required to be there in the driver. Change the same for the SD card node
which is not yet supported in kernel. This also syncs the main_pmx0 node
as a side effect.
Also change the name of the driver to match the compatible in kernel.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
We should use predefined constants instead of magic numbers.
Move some constant definitions from include/pe.h to
include/asm-generic/pe.h.
Use these constants in crt0_*_efi.S.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
So far USB was not enabled for the Allwinner H6 boards, as the PHY
driver was not ready and the clock gates were missing. Since this is now
fixed, let's add the PHY and the OHCI/EHCI drivers to the build, for
all existing H6 boards.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com> # Pine-H64
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Probably for no particular reason SUNXI_GPIO was still defined the "old
way", in header files only.
Introduce SUNXI_GPIO to the Kconfig file in drivers/gpio to remove
another line from our dreadful config_whitelist.txt.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com> # Pine-H64
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Add some basic line delay values to be used with DDR3 DRAM chips on
some H6 TV boxes.
Taken from a register dump after boot0 initialised the DRAM.
Put them as the default delay values for DDR3 DRAM until we know better.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Add a routine to program the timing parameters for DDR3-1333 DRAM chips
connected to the H6 DRAM controller.
The values were gathered from doing back-calculations from a register
dump, trying to match them up with the official JEDEC DDDR3 spec.
If in doubt, the register dump values were taken for now, but the JEDEC
recommendation were added as a comment.
Many thanks to Jernej for contributing fixes!
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
At the moment the H6 DRAM driver only supports LPDDR3 DRAM.
Extend the driver to cover DDR3 DRAM as well.
The changes are partly motivated by looking at the ZynqMP register
documentation, partly by looking at register dumps after boot0/libdram
has initialised the controller.
Many thanks to Jernej for contributing some fixes!
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Currently the H6 DRAM driver only supports one kind of LPDDR3 DRAM.
Split the timing parameters for this LPDDR3 configuration into a
separate file, to allow selecting an alternative later at compile time
(as the sunxi-dw driver does).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The DRAM controller manual suggests to first program the PHY
initialisation parameters to the PHY_PIR register, and then set bit 0 to
trigger the initialisation. This is also used in boot0.
Follow this recommendation by setting bit 0 in a separate step.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Using memcpy() is, however tempting, not a good idea: It depends on the
specific implementation of memcpy, also lacks barriers. In this
particular case the first registers were written using 64-bit writes,
and the last register using four separate single-byte writes.
Replace the memcpy with a proper loop using the writel() accessor.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Add mcu cpsw and its components along with scm_conf node
to have ethernet functional.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The Beelink X2 is an STB based on the Allwinner H3 SoC with a uSD slot,
2 USB ports( 1 * USB-2 Host, 1 USB OTG), a 10/100M ethernet port using the
SoC's integrated PHY, Wifi via an sdio wifi chip, HDMI, an IR receiver, a
dual colour LED and an optical S/PDIF connector.
Linux commit details about the sun8i-h3-beelink-x2.dts sync:
"ARM: dts: sun8i: h3: Add ethernet0 alias to Beelink X2"
(sha1: cc4bddade114b696ab27c1a77cfc7040151306da)
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Since we have limited resources in SPL, it is the best interest
to keep the SPL as small as possible and that includes the DTB.
There are a few items in the device tree that can be removed,
because these boards don't use them.
Signed-off-by: Adam Ford <aford173@gmail.com>
The MMC card-detect pin was incorrectly defined which was fixed.
This patch resync's the dts and removes the u-boot specific fix.
Signed-off-by: Adam Ford <aford173@gmail.com>
The USE_TINY_PRINTF symbol only changes things within SPL and TPL
builds, so make it depend on that support. Next, make it default as
within these cases we should rarely have need of more advanced print
formats outside of the debug context.
To do this, in a few cases we need to correct our Kconfig dependencies
as we had cases of non-SPL targets select'ing this symbol. Finally, in
the case of a few boards we really do need the full printf
functionality.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts LEGO MINDSTORMS EV3 to the driver model. MMC, SERIAL, SPI
and SPI_FLASH are converted.
The device tree contains only the minimal nodes required by U-Boot
since the size of U-Boot is limited to 256K on this device.
Signed-off-by: David Lechner <david@lechnology.com>
Since pinctrl_stm32 driver update, each gpio bank is now binded
by pinctrl driver. The compatible string "st,stm32-gpio" becomes
useless, remove it.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
This patch solves the following warnings:
arch/arm/mach-stm32mp/bsec.c: In function 'stm32mp_bsec_read':
warning: comparison between signed and unsigned integer expressions [-Wsign-compare]
if (offset >= STM32_BSEC_OTP_OFFSET) {
^~
arch/arm/mach-stm32mp/bsec.c: In function 'stm32mp_bsec_write':
warning: comparison between signed and unsigned integer expressions [-Wsign-compare]
if (offset >= STM32_BSEC_OTP_OFFSET) {
^~
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This patch solves the following warnings:
arch/arm/mach-stm32mp/cpu.c:378:16: warning: comparison between signed
and unsigned integer expressions [-Wsign-compare]
if (instance > ARRAY_SIZE(serial_addr))
^
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add support of Trusted boot chain with OP-TEE
- reserved 32MB at the end of the DDR for OP-TEE
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Synchronize device tree with v5.2-rc4 label and
update the associated u-boot dtsi.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Tested-by: Pierre-Jean Texier <pjtexier@koncepto.io>
U-Boot should disable nodes in device tree if needed according
ETZPC status in ft_system_setup().
ETZPC itself use an array on addresses to do the match between the status
bits and the node.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add IPCC mailbox support on stm32mp157 eval and disco boards.
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
- SPL SATA enhancements to allow booting from RAW SATA device
needed for Clearfog (Baruch)
- Enable SATA booting on Clearfog (Baruch)
- Misc changes to Turris Omnia (Marek)
- Enable CMD_BOOTZ and increase SYS_BOOTM_LEN on crs305-1g-4s
(Luka)
- Enable FIT support for db-xc3-24g4xg (Chris)
- Enable DM_SPI on Keymile Kirkwood board with necessary changes
for this (Pascal)
- Set 38x and 39x AVS on lower frequency (Baruch)
- import DT updates from Linux
- add UniPhier SPI controller driver
- make U-Boot image for 64bit SoCs position independent
- tidy up various init code for next generation SoCs
- misc cleanups
-----BEGIN PGP SIGNATURE-----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=X9wS
-----END PGP SIGNATURE-----
Merge tag 'uniphier-v2019.10' of https://gitlab.denx.de/u-boot/custodians/u-boot-uniphier
UniPhier SoC updates for v2019.10
- import DT updates from Linux
- add UniPhier SPI controller driver
- make U-Boot image for 64bit SoCs position independent
- tidy up various init code for next generation SoCs
- misc cleanups
