Some 86xx chips use CCB as the base clock for the I2C, and others used CCB/2.
There is no pattern that can be used to determine which chips use which
frequency, so the only way to determine is to look up the actual SOC
designation and use the right value for that SOC.
Signed-off-by: Timur Tabi <timur@freescale.com>
This patch fixes a problem with DIMMs that have 8 banks. Now the
MCIF0_MBxCF register will be setup correctly for this setup too.
This was noticed with the 512MB DIMM on Canyonlands/Glacier.
Signed-off-by: Stefan Roese <sr@denx.de>
Newer gcc's might be configured to enable autovectorization by default.
If we happen to build with one of those compilers we will get SPE
instructions in random code.
-mno-spe disables the compiler for automatically generating SPE
instructions without our knowledge.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* adjust __spin_table alignment to match ePAPR v0.94 spec
* loop over all cpus when determing who is up. This fixes an issue if
the "boot cpu" isn't core0. The "boot cpu" will already be in the
cpu_up_mask so there is no harm
* Added some protection in the code to ensure proper behavior. These
changes are explicitly needed but don't hurt:
- Added eieio to ensure the "hot word" of the table is written after
all other table updates have occurred.
- Added isync to ensure we don't prefetch loading of table entries
until we a released
These issues we raised by Dave Liu.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Since the current dflush() implementation is know to have some problems
(as seem on lwmon5 ECC init) this patch removes it completely and replaces
it by using clean_dcache_range().
Tested on Katmai with ECC DIMM.
Signed-off-by: Stefan Roese <sr@denx.de>
On ppc405EP and ppc405GP (at least) the ebc is directly attached to the plb
and not to the opb. This patch will try to fixup /plb/ebc if /plb/opb/ebc
doesn't exist.
Signed-off-by: Markus Brunner <super.firetwister@gmail.com>
The PCIe root-complex/endpoint setup as configured via the "pcie_mode"
environment variable will now get passed to the Linux kernel by setting
the device_type property of the PCIe device tree node. For normal root-
complex configuration it will keep its defaults value of "pci" and for
endpoint configuration it will get changed to "pci-endpoint".
Signed-off-by: Stefan Roese <sr@denx.de>
This reverts commit 70431e8a73 which has
proven problematic getting right from the start at least on 83xx and
4xx.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
eg. because of rounding error we can get 799Mhz instead of 800Mhz.
Introduced DIV_ROUND_UP and roundup taken from linux kernel.
Signed-off-by: Dejan Minic <minic@freescale.com>
Signed-off-by: Srikanth Srinivasan <srikanth.srinivasan@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Andy Fleming <afleming@freescale.com>
Fix ARM based DaVinci DM644x timer overflow handling and cleanup timer code.
Changes:
- Remove *_masked() functions as noted by Wolfgang
- Adapt register naming to recent TI spec (sprue26, March 2007)
- Fix reset_timer() handling
- As reported by Pieter [1] the overflow fix introduced a delay of factor 16 (e.g 2 seconds became 32). While the overflow fix is basically okay, it missed to divide udelay by 16, too. Fix this.
[1] http://article.gmane.org/gmane.comp.boot-loaders.u-boot/38179
- Remove software division of timer count value (DIV(x) macro) and do it in hardware (TIM_CLK_DIV).
Many thanks to Troy Kisky <troy.kisky@boundarydevices.com> and Pieter Voorthuijsen <pieter.voorthuijsen@Prodrive.nl> for the hints & testing!
Patch is compile tested with davinci_dvevm & sonata & schmoogie configuration and tested by Pieter on DaVinci EVM hardware.
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
Acked-by: Pieter Voorthuijsen <pieter.voorthuijsen@Prodrive.nl>
dcache_enable() was missing for 440 and the patch
017e9b7925 ["allow ports to override bootelf
"] behavior uses this function.
Note: Currently the cache handling functions like
d/icache_disable/enable() are NOP's on 440. This may be changed in the
future.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch assigns the correct EBC clock for 405GP(r) CPUs
to PPC4xx_SYS_INFO structure. Without this patch U-Boot
uses an uninitialized EBC clock in its startup message.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Some 85xx chips use CCB as the base clock for the I2C. Some use CCB/2, and
some use CCB/3. There is no pattern that can be used to determine which
chips use which frequency, so the only way to determine is to look up the
actual SOC designation and use the right value for that SOC.
Update immap_85xx.h to include the GUTS PORDEVSR2 register.
Signed-off-by: Timur Tabi <timur@freescale.com>
Currently U-Boot crashes in ppc_4xx_eth_init on sequoia
with cache enabled (TLB Parity exeption). This patch
fixes the problem.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Currently U-Boot crashes on sequoia board in CPU POST if
cache is enabled (CONFIG_4xx_DCACHE defined). The cache
won't be disabled by change_tlb before CPU POST because
there is an insufficient adress range check since
CFG_MEM_TOP_HIDE was introduced. This patch tries to fix
this problem.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Current assembler codes are inconsistent in the way of register jump
instruction usage; some use jr, some use j. Of course GNU as allows both
usages, but as can be expected from `Jump Register' the mnemonic `jr' is
more intuitive than `j'. For example, Linux doesn't have `j <reg>' usage
at all.
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
The cross compiler is responsible for providing the correct libraries
and the logic to find the linking libraries.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Cache operations have to take line address (addr), not start_addr.
I noticed this bug when debugging ping failure.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
This patch adds the core support for Freescale mx31
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
32-bit wide ECC memory modules report 40-bit width.
Changed the DIMM data bus width test to 'less than 64' instead of 'equal 32'.
Signed-off-by: Lee Nipper <lee.nipper@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
We were looking at the wrong memory offset to determine of a secondary
cpu had been spun up or not. Also added a warning message if the
all the secondary cpus we expect don't spin up.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The recent change introduced by 'Update SVR numbers to expand support'
now requires that we use SVR_SOC_VER instead of SVR_VER if we want
to compare against a particular processor id.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch fixes a problem with the RGMII setup of the 460GT. The 460GT
has 2 RGMII instances and we need to configure the 2nd RGMII instance
for the EMAC2+3 channels.
Signed-off-by: Stefan Roese <sr@denx.de>
fdt.c: In function 'ft_cpu_setup':
fdt.c:33: warning: implicit declaration of function 'do_fixup_by_prop_u32'
fdt.c:39: warning: implicit declaration of function 'do_fixup_by_compat_u32'
fdt.c:43: warning: implicit declaration of function 'fdt_fixup_ethernet'
fdt.c:45: warning: implicit declaration of function 'fdt_fixup_memory'
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
AT91CAP9 and AT91SAM9 SoCs are very close hardware wise, so a
common infrastructure can be used. Let this infrastructure be
named after the AT91SAM9 family, and move the existing AT91CAP9
files to the new place.
Signed-off-by: Stelian Pop <stelian@popies.net>
The timer on AT91CAP9/AT91SAM9 is supplied by the SoC, and not by
the board, so use timer_init() instead of interrupt_init().
Signed-off-by: Stelian Pop <stelian@popies.net>
When the version_string function in start.S is not 4-byte align,
it will cause the compiler generates "unaligned opcodes detected
in executable segment". This issue affects all ColdFire CPUs.
By adding .align 4 after CONFIG_IDENT_STRING, it will pad 0's if
it is not aligned.
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Acked-by: John Rigby <jrigby@freescale.com>
This board never went into production
Signed-off-by: Zachary P. Landau <zachary.landau@labxtechnologies.com>
Acked-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Acked-by: John Rigby <jrigby@freescale.com>
All of the duplicated code for Blackfin processors and boot modes have been
unified. After all, the core is the same for all processors, just the
peripheral set differs (which gets handled in the drivers).
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This fixes a naming bug for at91rm9200 lowlevel init code:
NOR boot flash is on chipselect 0, not chipselect 2. This
makes code use the register name from chip datasheets.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This patch adds the core support for Freescale mx31
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
- Adapt register naming to recent TI spec (sprue26, March 2007)
- Fix reset_timer() handling
- As reported by Pieter [1] the overflow fix introduced a
delay of factor 16 (e.g 2 seconds became 32). While the
overflow fix is basically okay, it missed to divide udelay by
16, too. Fix this.
[1] http://article.gmane.org/gmane.comp.boot-loaders.u-boot/38179
- Remove software division of timer count value (DIV(x)
macro) and do it in hardware (TIM_CLK_DIV).
Many thanks to Troy Kisky <troy.kisky@boundarydevices.com>
and Pieter Voorthuijsen <pieter.voorthuijsen@Prodrive.nl> for
the hints & testing!
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
Acked-by: Pieter Voorthuijsen <pieter.voorthuijsen@Prodrive.nl>
Remove a few absolute references to CFG_MONITOR_BASE for ppc/mpc83xx
and use GOT relative reference.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
in the spirit of commit 1ced121600,
85xx's "Update SVR numbers to expand support", simplify SPRIDR processing
and processor ID display. Add REVID_{MAJ,MIN}OR macros to make
REVID dependent code simpler. Also added PARTID_NO_E and IS_E_PROCESSOR
convenience macros.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
delete ddr_clk and use mem_clk instead. Rename other ddr_*_clk to
mem_*_clk for consistency's sake.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch add support PCI of SuperH base code and SH7780 specific code.
Signed-off-by: Yusuke Goda <goda.yusuke@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This bug was introduced with commit aee747f19b
which enabled CFG_4xx_GPIO_TABLE for PPC405 and unintentionally
disabled the setting of the emac noise filter bits for PPC405EP when CFG_4xx_GPIO_TABLE is set.
Signed-off-by: Markus Brunner <super.firetwister@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
On PPC440EPx without a bootstrap I2C EEPROM, the PLL can be reconfigured
after startup to change the speed of the clocks. This patch adds the
option CFG_PLL_RECONFIG. If this option is set to 667, the CPU
initialization code will reconfigure the PLL to run the system with a CPU
frequency of 667MHz and PLB frequency of 166MHz, without the need for an
external EEPROM.
Signed-off-by: Mike Nuss <mike@terascala.com>
Acked-by: Stefan Roese <sr@denx.de>
This patch adds support for the AMCC Glacier 460GT eval board.
The main difference to the Canyonlands board are listed here:
- 4 ethernet ports instead of 2
- no SATA port
- no USB port
Currently EMAC2+3 are not working. This will be fixed in a later
release.
Signed-off-by: Stefan Roese <sr@denx.de>
Provide a board_lmb_reserve helper function to ensure we reserve
the page of memory we are using for the boot page translation code.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The following changes are needed to be inline with ePAPR v0.81:
* r4, r5 and now always set to 0 on boot release
* r7 is used to pass the size of the initial map area (IMA)
* EPAPR_MAGIC value changed for book-e processors
* changes in the spin table layout
* spin table supports a 64-bit physical release address
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
get_ddr_freq() and get_bus_freq() used get_sys_info() each time they were
called. However, get_sys_info() recalculates extraneous information when
called each time. Have get_ddr_freq() and get_bus_freq() return memoized
values from global_data instead.
Signed-off-by: James Yang <James.Yang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Show the DDR memory data rate in addition to the memory clock
frequency. For DDR/DDR2 memories the memory data rate is 2x the
memory clock.
Signed-off-by: James Yang <James.Yang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Speed up get_tbclk() by referencing pre-computed bus clock
frequency value from global data instead of sys_info_t. Fix
rounding of result to nearest; previously it was rounding
upwards.
Signed-off-by: James Yang <James.Yang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
FSL has taken to using SVR[16:23] as an SOC sub-version field. This
is used to distinguish certain variants within an SOC family. To
account for this, we add the SVR_SOC_VER() macro, and update the SVR_*
constants to reflect the larger value. We also add SVR numbers for all
of the current variants. Finally, to make things neater, rather than
use an enormous switch statement to print out the CPU type, we create
and array of SVR/name pairs (using a macro), and print out the CPU name
that matches the SVR SOC version.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Added the cpu command that provides a generic mechanism to get status,
reset, and release secondary cores in multicore processors.
Added support for using the ePAPR defined spin-table mechanism on 85xx.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Added the cpu command that provides a generic mechanism to get status,
reset, and release secondary cores in multicore processors.
Added support for using the ePAPR defined spin-table mechanism on 85xx.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
When we go to 36-bit physical addresses we need to keep the concept of
the physical CCSRBAR address seperate from the virtual one.
For the majority of boards CFG_CCSBAR_PHYS == CFG_CCSRBAR
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
device_type = "soc" is being deprecated, newer device trees will use
"fsl,soc" and/or "fsl,immr" for the soc nodes.
This patch also adds clock-frequency property for soc nodes (the same
value as bus-frequency).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
The following changes are based on kernel UCC ethernet performance:
1. Make the CSB bus pipeline depth as 4, and enable the repeat mode
2. Optimize transactions between QE and CSB. Added CFG_SPCR_OPT
switch to enable this setting.
The following changes are based on the App Note AN3369 and
verified to improve memory latency using LMbench:
3. CS0_CONFIG[AP_n_EN] is changed from 1 to 0
4. CS0_CONFIG[ODT_WR_CONFIG] set to 1. Was a reserved setting
previously.
5. TIMING_CFG_1[WRREC] is changed from 3clks to 2clks (based on
Twr=15ns, and this was already the setting in DDR_MODE)
6. TIMING_CFG_1[PRETOACT] is changed from 3clks to 2clks. (based on
Trp=15ns)
7. TIMING_CFG_1[ACTTOPRE] is changed from 9clks to 6clks. (based on
Tras=40ns)
8. TIMING_CFG_1[ACTTORW] is changed from 3clks to 2clks. (based on
Trcd=15ns)
9. TIMING_CFG_1[REFREC] changed from 21 clks to 11clks. (based on
Trfc=75ns)
10. TIMING_CFG_2[FOUR_ACT] is changed from 10 clks to 7clks. (based
on Tfaw=50ns)
11. TIMING_CFG_2[ADD_LAT] and DDR_MODE[AL] changed from 0 to 1 (based
on CL=3 and WL=2).
Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Include FEC specific nodes in ft_cpu_setup only if CONFIG_MPC5xxx_FEC is
defined. Systems without FEC, i.e. no FEC node in DTB, should be possible.
Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Add setup_c0_status from Linux. For the moment we disable interrupts, set
CU0, mark the kernel mode, and clear ERL and EXL. This is good enough for
reset-time configuration and will work well across most processors.
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
Without this change, we'll be suffering from deffered WATCH exception
once Status.EXL is cleared. Make sure Cause.WP is cleared.
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
We do Hit_Writeback_Inv_D and Hit_Invalidate_I. You might think that you
don't need to do Hit_Invalidate_I, but flush_cache() needs it since this
function is used not only in U-Boot specfic programs but also at loading
target binaries.
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
Currently we do 1) Index_Store_Tag_I, 2) Fill and 3) Index_Store_Tag_I
again per a loop for I-cache initialization. But according to 'See MIPS
Run', we're encouraged to use three separate loops rather than combining
them *for both I- and D-cache*. This patch tries to fix this.
In accordance with fixing above, mips_init_[id]cache are separated from
mips_cache_reset(), and rewrite cache loops are completely rewritten with
useful macros.
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
This patch replaces the current function definitions with NESTED, LEAF
and END macro. They specify some more additional information about the
function; an alignment of symbol, type of symbol, stack frame usage, etc.
These information explicitly tells the assembler and the debugger about
the types of code we want to generate.
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
The initial intension of having mips_cache_lock() was to use the cache
as memory for temporary stack use so that a C environment can be set up
as early as possible.
But now mips_cache_lock() follow lowlevel_init(). We've already have the
real memory initilaized at this point, therefore we could/should use it.
No reason to lock at all.
Other problems:
Cache locking is not consistent across MIPS implementaions. Some imple-
mentations don't support locking at all. The style of locking varies -
some support per line locking, others per way, etc. Some parts use bits
in status registers instead of cache ops. Current mips_cache_lock() is
not necessarily general-purpose.
And this is worthy of special mention; once U-Boot/MIPS locks the lines,
they are never get unlocked, so the code relies on whatever gets loaded
after U-Boot to re-initialize the cache and clear the locks. We're sup-
posed to have CFG_INIT_RAM_LOCK and unlock_ram_in_cache() implemented,
but leave the situation as it is for a long time.
For these reasons, I proposed the removal of mips_cache_lock() from the
global start-up code.
This patch adds CFG_INIT_RAM_LOCK_MIPS to make existing users aware that
*things have changed*. If he wants the same behavior as before, he needs
to have CFG_INIT_RAM_LOCK_MIPS in his config file.
If we don't have any regression report through several releases, then
we'll remove codes entirely.
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
Acked-by: Andrew Dyer <amdyer@gmail.com>
Modify the RTC API to provide one a status for the time reported by
the rtc_get() function:
0 - a reliable time is guaranteed,
< 0 - a reliable time isn't guaranteed (power fault, clock issues,
and so on).
The RTC chip drivers are responsible for providing this info if the
corresponding chip supports such functionality. If not - always
report that the time is reliable.
The POST RTC test was modified to detect the RTC faults utilizing
this new rtc_get() feature.
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
460EX doesn't support a fixed bootstrap option to boot from 512 byte page
NAND devices. The only bootstrap option for NAND booting is option F for
2k page devices. So to boot from a 512 bype page device, the I2C bootstrap
EEPROM needs to be programmed accordingly.
This patch adds basic NAND booting support for the AMCC Canyonlands aval
board and also adds support to the "bootstrap" command, to enable NAND
booting I2C setting.
Tested with 512 byte page NAND device (32MByte) on Canyonlands.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch is a rework of the 4xx interrupt handling done while
adding the 460EX/GT support. Interrupts are needed on 4xx for the
EMAC driver.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch changes the physical addess parameter from 32bit to 64bit.
This is needed for 36bit 4xx platforms to access areas located
beyond the 4GB border, like SoC peripherals (EBC etc.).
Signed-off-by: Stefan Roese <sr@denx.de>
Every now and then a Sequoia board (or equivalent hardware) had
problems connecting to a Gigabit capable network interface.
There were differences in the PHY setup between Linux and U-Boot.
This patch fixes the problem. Apparently "remote fault" is being set,
which signals to some devices (on the other end of the cable) that a
fault has occurred, while other devices ignore it. I believe the RF bit
was causing the issue, but I removed T4 also, to match up with Linux.
Signed-off-by: Mike Nuss <mike@terascala.com>
The 405EZ only supports 512 bytes of rx-/tx-fifo EMAC sizes. But
currently 4k/2k is configured. This patch fixes this issue.
Thanks to Thomas Kindler <tkindler@lenord.de> for pointing this out.
Signed-off-by: Stefan Roese <sr@denx.de>
Adds PCI support for MPC5121
Tested with drivers/net/rtl8139.c
Support is conditional since PCI on old silicon does not work.
ads5121_PCI_config turns on PCI
In this version, condition compilation of PCI code has been moved
from ifdef in board/ads5121/pci.c to board/ads5121/Makefile as
suggested by Jean-Christophe PLAGNIOL-VILLARD
Signed-off-by: John Rigby <jrigby@freescale.com>
U-Boot crashes in the net loop if CONFIG_4xx_DCACHE is
enabled. To reproduce the problem ensure that 'ethrotate'
environment variable isn't set to "no" and then run
"tftp 200000 not_existent_file".
This patch tries to fix the issue.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
There is no reason to icbi when invalidating the temporary stack in
the d-cache. Its impossible on e500 to have the i-cache contain
any addresses in the temp stack and it can be problematic in generating
transactions on the bus to non-valid addresses.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The source vector for the ECM was being set to 2,
but that's what the source vector for DDR was being
set to. Change it to 1.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Commit 0db37dc... (and some others) changed the INIT_RAM TLB
mappings to be unguarded. This collided with an existing "bug"
where the mappings for the INIT_RAM were being kept around.
This meant that speculative loads to those addresses were
succeeding in the TLB, and going out to the bus, where they
were causing an exception (there's nothing at that address). The
Flash code was coincidentally causing such a speculative load.
Rather than go back to mapping the INIT RAM as guarded, we fix
it so that the entries for the INIT_RAM are invalidated. Thus
the speculative loads will fail in the TLB, and have no effect.
Signed-off-by: Andy Fleming <afleming@freescale.com>
This reduces the build time by ~10%. Here's the gth2_config example.
BEFORE AFTER
real 0m31.441s 0m27.833s
user 0m24.766s 0m23.045s
sys 0m10.425s 0m7.468s
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
New uImage format (Flattened Image Tree) requires libfdt
functionality, print out error message if CONFIG_OF_LIBFDT
is not defined.
New uImage support is enabled by defining CONFIG_FIT (and CONFIG_OF_LIBFDT).
This commit turns it on by default.
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
This is the proper fix for a missing closing brace in the function
ft_cpu_setup() noticed by joe.hamman <at> embeddedspecialties.com.
The ft_cpu_setup() function in mpc8641hpcn.c should have been
removed earlier as it was under the obsolete CONFIG_OF_FLAT_TREE,
but was missed. Only, the sbc8641d was nominally still using it.
It all got ripped out, and the funcality that was in ft_board_setup()
was refactored to remove the CPU portions into the new file
cpu/mpc86xx/fdt.c instead. Make sbc8641d use this now.
Based loosely on an original patch from joe.hamman@embeddedspecialties.com
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Update global_data to define i2c1_clk and i2c2_clk to 85xx and 86xx.
Update the get_clocks() function in 85xx and 86xx to determine the I2C
clock frequency and store it in gd->i2c1_clk and gd->i2c2_clk.
Signed-off-by: Timur Tabi <timur@freescale.com>
R29 was an unlucky choice as with recent toolchains (gcc-4.2.x) gcc
will refuse to use load/store multiple insns; instead, it issues a
list of simple load/store instructions upon function entry and exit,
resulting in bigger code size, which in turn makes the build for a
few boards fail.
Use r2 instead.
Signed-off-by: Wolfgang Denk <wd@denx.de>
This patch enables the OneNAND boot within U-Boot.
Before this work, we used another OneNAND IPL called X-Loader based
on open source. With this work, we can build the oneboot.bin image
without other program.
The build sequence is simple.
First, it compiles the u-boot.bin
Second, it compiles OneNAND IPL
Finally, it becomes the oneboot.bin from OneNAND IPL and u-boot.bin
The mechanism is similar with NAND boot except it boots from itself.
Another thing is that you can only use the OneNAND IPL only to work
other bootloader such as RedBoot and so on.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Fix arm926ejs compile when SKIP_LOWLEVEL_INIT is on.
cpu/arm926ejs/start.o: In function `cpu_init_crit':
.../cpu/arm926ejs/start.S:227: undefined reference to `lowlevel_init'
Signed-off-by: Stelian Pop <stelian@popies.net>
Move the flat device tree setup for QE related devices into
a common file shared between 83xx & 85xx platforms that have QE's.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Changes to match 5121 device tree going mainline in 2.6.25.
Change OF_SOC from "soc5121" to plain "soc".
Remove unneeded "ref-frequency" fixups.
Remove "address" enetaddr fixup.
Add bus-frequency fixup for old OF_SOC so old
kernels with old device trees will work with new
u-boot with 66MHz IPS clock
Signed-off-by: John Rigby <jrigby@freescale.com>
The existing code assumes the SDRAM row refresh period should always
be 15.6 us. This is not always true, and indeed on the ATNGW100, the
refresh rate should really be 7.81 us.
Add a refresh_period member to struct sdram_info and initialize it
properly for both ATSTK1000 and ATNGW100. Out-of-tree boards will
panic() until the refresh_period member is updated properly.
Big thanks to Gerhard Berghofer for pointing out this issue.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
This patch allows us to use the 'gd' pointer (and thus environment
and everything else associated with it) from interrupt context on
arm920t.
Signed-off-by: Harald Welte <laforge@openmoko.org>
This patch adds a IRQ demultiplexer callback to the arm920 cpu core code,
plus a stub implementation of it for the S3C2410.
The purpose is to allow arm920t implementations such as the s3c24x0 to
implement interrupt handlers in u-boot without having to touch core
arm920t code.
Signed-off-by: Harald Welte <laforge@openmoko.org>
The current ndfc HW ECC implementation swaps the first two ECC bytes.
But the 4xx NDFC already uses the SMC (Smart Media Card) ECC ordering,
so this swapping in the HW ECC driver is bogus. This patch fixes this
problem and now really uses the SMC ECC byte order.
Thanks to Sean MacLennan for pointing this out.
Signed-off-by: Stefan Roese <sr@denx.de>
MMC support for X_Scale PXA is broken and does not work.
Mainly, the mmc_init() function cannot recognize current SD/MMC cards.
There were already some patches around the world but none of them was
merged into the official u-boot tree.
This patch makes order fixing this issue. Resubmit after code cleanup.
Applied and tested on PXA 270 (TrizepsIV module).
Signed-off-by: Stefano Babic <sbabic@denx.de>
Adds the support code in cpu/mpc86xx for the new law setup code
recently created fsl_law.c, and changes the MPC8641HPCN config
to use this code.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
* split the BAT initialization so that only 2 BATs (for the boot page
and stack) are programmed very early on. The rest are initialized later.
* Move other BAT setup, ccsrbar setup, and law setup later in the code
after translation has been enabled.
These changes will facilitate the moving of law and BAT initialization
to C code, and will aid with 36-bit physical addressing support.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
enables the RTS signal with CONFIG_SERIAL_RTS_ACTIVE.
No handshaking is done, but the active RTS signal allows to
connect to the target using a PC which is using RTS/CTS
handshake, and does no harm if the PC is set to ignore RTS.
Signed-off-by: Michael Schwingen <michael@schwingen.org>
allow to load the microde from flash or ram by download it through
the serial or other.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Stefan Roese <sr@denx.de>
Hi,
the following patch adds support to move the IXP42X NPE firmware to a
separate flash block, whose start address is defined in
CONFIG_IXP4XX_NPE_EXT_UCODE_BASE. Using that, it is possible to build
NPE-enabled u-boot without copyright problems due to the NPE firmware.
I hope the patch applies, I get whitespace-related differences in the NPE
files due to trailing whitespace in the original versions.
Signed-off-by: Michael Schwingen <michael@schwingen.org>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
The commit 9e89647889
will cause the mpc8315erdb board can't boot up.
The patch fix that bug, and remove the duplicated #ifdef
CFG_SPCR_TSECEP code and clean the SCCR_TSEC2 for
MPC8313E processor.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Now that all boards have been converted, remove old config code and the
config option for the new style.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Reworked the initial processor initialzation sequence:
* introduced cpu_early_init_f that is run in address space 1 (AS=1)
* Moved TLB/LAW and CCSR init into cpu_early_init_f()
* Reworked initial asm code to do most of the core init before TLBs
The main reasons for these changes are to allow handling of 36-bit phys
addresses in the future and some of the issues that will exist when we
do that.
There are a few caveats on what can be initialized via the LAW and TLB
static tables:
* TLB entry 14/15 can't be initialized via the TLB table
* any LAW that covers the implicit boot window (4G-8M to 4G) must map to
the code that is currently executing.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add a set of functions to manipulate TLB entries:
* set_tlb() - write a tlb entry
* invalidate_tlb() - invalidate a tlb array
* disable_tlb() - disable a variable size tlb entry
* init_tlbs() - setup initial tlbs based on static table
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Move the initialization of the LAWs into C code and provide an API
to allow modification of LAWs after init.
Board code is responsible to provide a law_table and num_law_entries.
We should be able to use the same code on 86xx as well.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
