And use this to set the GMAC Transmit Clock Delay Chain value on Banana
boards, rather then keying of CONFIG_TARGET_FOO.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
This patch adds basic constructs in the ARMv8 u-boot code
to handle and apply Cortex-A57 specific erratas.
As and example, the framework showcases how erratas 833069, 826974
and 828024 can be handled and applied.
Later on this framework can be extended to include other
erratas.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Some versions of Exynos5 supports High-Speed I2C,
on few interfaces, this change allows support this.
The new flag is: PINMUX_FLAG_HS_MODE
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Akshay Saraswat <akshay.s@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
On the DRA72x (J6Eco) EVM one PMIC SMPS is powering three SoC
core rails. This concept of using one SMPS to supply multiple
core domains (in various, although limited combinations, per
primary device use case) has now become common and is used by
many customer J6/J6Eco designs; it is supported by a number of
corresponding PMIC OTP versions.
This patch implements correct operation of the core voltages
scaling routine by ensuring that each SMPS that is supplying
more than one domain shall be written only once, and with the
highest voltage of those fused in the SoC (or of those defined
in the corresponding header if fuse read is disabled or fails)
for the power rails belonging to the group.
The patch also replaces some PMIC-related magic numbers with
the appropriate definitions. The default OPP_NOM voltages for
the DRA7xx SoCs are updated as well, per the latest DMs.
Signed-off-by: Lubomir Popov <l-popov@ti.com>
As QSPI/DSPI and IFC are pin multiplexed, QSPI and DSPI are
only enabled in QSPI boot, and disabled in other boot modes.
IFC is enabled in NOR/NAND/SD boot, and disabled in QSPI boot.
This patch will add fdt support for the above rules.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
CAAM is connected to CCI-400 S0 slave interface. Disable snooping for
S0 will cause CAAM self test failure. This patch is to enable snooping
for S0 slave interface. These CCI-400 operations are moved to
board_early_init_f() to be initialized earlier. For S4 slave interface,
issuing of snoop requests and DVM message requests are enabled.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
If CONFIG_OF_CONTROL is enabled, lib/fdtdec.c is compiled.
It includes <asm/gpio.h> and then <asm/gpio.h> includes
<asm/arch/gpio.h>. As a result, all the SoCs that enable
CONFIG_OF_CONTROL must have <asm/arch/gpio.h> even if they
do not support GPIO.
The right fix would be to split the lib/fdtdec.c to remove
dependency on GPIO.This commit adds a dummy <asm/arch/gpio.h>
to support OF_CONTROL for LS102x platform. This dummy header
will be removed after FDT-GPIO stuff is fixed correctly.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch reverts to use ge0_clk125 for eTSEC clock muxing. For SAI and
CAN which are pin multiplexed with RGMII1 in EC1 of RCW, ge2_clk125 will
be used via hwconfig.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Internal memory controller counters can reach a bad state after
training in DDR4 mode if accumulated ECC or DBI mode is eanbled.
Signed-off-by: York Sun <yorksun@freescale.com>
Match the suffixes of SG_MEMCONF_* macros with SZ_* macros defined
by <linux/sizes.h> for readability.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
The DDR PHY training function, ddrphy_prepare_training() would not
work if compiled with GCC 4.9.
The struct ddrphy (arch/arm/include/asm/arch-uniphier/ddrphy-regs.h)
is specified with __packed because it represents a hardware register
mapping, but it turned out to cause a problem on GCC 4.9.
If -mno-unaligned-access is specified (yes, it is in
arch/arm/cpu/armv7/config.mk), GCC 4.9 is aware of the
__attribute__((packed)) and generates extra instructions to perform
the memory access in a way that does not cause unaligned access.
(Actually it is not need here because the register base, the first
argument of the ddrphy_prepare_training(), is always given with a
4-byte aligned address.)
Anyway, as a result, readl() / writel() is divided into byte-wise
accesses. The problem is that this hardware only accepts 4-byte
register access. Byte-wise accesses lead to unexpected behavior.
There are some options to avoid this problem.
[1] Remove -mno-unaligned-access
[2] Add __aligned(4) along with __packed to struct ddrphy
[3] Remove __packed from struct ddrphy
[1] solves the problem for ARMv7, but it does not for pre-ARMv6 and
ARMv6-M architectures where -mno-unaligned-access is default.
So, [1] does not seem reasonable in terms of code portability.
Both [2] and [3] work well, but [2] seems too much. All the members
of struct ddrphy have the u32 type. No padding would be inserted
even if __packed is dropped.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Tom Rini <trini@ti.com>
Hookup OTG USB controller support and enable the otg controller + USB-keyb
on various tablets.
This allows tablet owners to interact with u-boot without needing to solder
a serial console onto their tablet PCB.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Testing has shown that on sun4i the display backend engine does not have
deep enough fifo-s causing flickering / tearing in full-hd mode due to
fifo underruns. On sun4i use the display frontend engine to do the dma from
memory, as the frontend does have deep enough fifo-s.
As added advantage of this is that it results in much better memory bandwidth
as it reduces the amount of dram bank switches, for more details see:
http://ssvb.github.io/2014/11/11/revisiting-fullhd-x11-desktop-performance-of-the-allwinner-a10.html
Note that this changes the pipeline searched for in the simplefb node, we can
get away with doing this now, since no kernel has yet shipped with simplefb
dtb nodes, and I will make sure to get a simplefb node with the new pipeline
into 3.19 before it ships.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
While working on adding more boards I noticed that we lack a config for
the 512M cubieboard, and that some of the new boards which I want to add also
have 512M and 1G variants, rather then adding 2 defconfig's for all of these,
lets switch the exising boards which have both a 512M and 1024M variant over
to the sun4i dram autoconfig code.
This also drops the foo_RAMSIZE_defconfig variants of boards where we currently
have 2 separate configs already.
Note:
1) The newly introduced CONFIG_DRAM_EMR1 kconfig value is not used with
a value other then its default for now, but we need this to be configurable
to support some new boards with auto dram config.
2) We always set all CONFIG_DRAM_foo values in defconfigs, even if they match
the defaults, this is done to make it more clear what values are used for a
certain board.
This has been tested on a Mele A1000, Mini-X and a Cubieboard, all 1G
variants, the dram autoconfig code has also been tested on a 512M mk802
(a defconfig for the mk802 is added in a later patch).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The clocks on the A80 are hooked up slightly different, add support for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add a headerfile with all the base addresses from the sun9i blocks.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
sun4i - sun8i have (aprox.) the same iomem layout, but sun9i is quite
different, so add a wrapper cpu.h which includes the right mach specific
cpu_sun#i.h based on mach, like we already do with clock.h and dram.h .
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Which pll-s are available depends on the machine type, move the
clock_get_pllX / clock_set_pllX prototypes to the clock_sun?i.h header files
so that we only declare what is actually available. e.g. clock_get_pll5p()
is not available on sun6i / sun8i, and with sun9i we get a completely
different set of plls.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
While running some tests with an Olinuxino-A13-Micro + a 7" Olimex LCD module
I noticed that the screen flickered. This is caused by the lcd display clk
phase reg value being set to 0, where it should be 1 in this setup.
This commit adds a Kconfig option for the lcd display clk phase, so that we
can set it per board. This defaults to 1, because looking at all the fex
files in sunxi-boards, that is by far the most used value.
This commit updated the Ippo and MSI Primo73 tablet defconfigs to override the
default of 1 with 0, as that is the correct value for those tablets, this
keeps the register settings the same as before this commit.
The Olinuxino-A13 defconfigs are not updated, changing the register setting
for these boards from 0 to 1, this is intentional.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Define two structure mx6sx_iomux_ddr_regs and mx6sx_iomux_grp_regs.
Add a new function mx6sx_dram_iocfg to configure dram io.
Since mx6sx only have one channel mmdc0, define a new empty macro MMDC1
to replace mmdc1->entry=value for mx6sx. And to other mx6 soc, MMDC1
effects as "mmdc1->entry=value".
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Most of the usb-controller init code found in ehci-sunxi.c also is necessary
to init the otg usb controller, so move it to a common place.
While at it also update various #ifdefs / defines for sun8i support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add support for VGA directly from the sunxi SoC / display engine.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add lcd output support, see the new Kconfig entries and doc/README.video for
how to enable / configure this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Modify sunxi_lcdc_pll_set to work with both tcon0 and tcon1, this is a
preparation patch for adding lcd support.
While at it also swap the divider search order, searching from low to
high, as the comment above the code says we should do. In cases where there
are multiple solutions this will result in picking a lower pll clock and
divider, which is more stable and saves power.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Some boards use GPIO-s on the pmic, one example of this is the A13-OLinuXino
board, which uses gpio0 of the axp209 for the lcd-power signal.
This commit adds support for gpio pins on the AXP209 pmic, the sunxi_gpio.c
changes are universal, adding gpio support for the other AXP pmics (when
necessary) should be a matter of adding the necessary axp_gpio_foo functions
to their resp. drivers, and add "#define AXP_GPIO" to their header file.
Note this commit only adds support for the non device-model version of the
gpio code, patches for adding support to the device-model version are very
welcome.
The string representation for these gpio-s is AXP0-#, the 0 in the AXP0 prefix
is there in case we need to support gpio-s on more then 1 pmic in the future.
At least A80 boards have 2 pmics, and we may end up needing to support gpio-s
on both.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Move a few mux defines around so that all the mux defines are properly sorted
by port number.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add a write to the "unknown" (*) register to enable auto input sync, when
initially adding sunxi hdmi output support this magic write from the android
kernel code was missed, causing lcdc -> hdmi encoder sync problems.
With this write added, we can drop the modesetting retries and the extra
delays added to work around these sync problems.
With the retries dropped there also is no need to 0 all the enable flags at
the beginning of the modeset, as they are initialized to 0 already by
engines_init.
*) "unknown" is the actual name of this register in the android kernel sources
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Anatolij Gustschin <agust@denx.de>
So far we've been programming the hdmi-encoder to send out dvi data over the
hdmi connector. This works well for most devices, including hdmi devices, but
not all devices accept dvi data on a hdmi input.
Add support for sending proper hdmi data over the hdmi output found on most
sunxi boards. This can be turned on by adding monitor=hdmi as option to the
video-mode env. variable.
A follow up patch will determine whether to send dvi or hdmi automatically when
EDID is used.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Anatolij Gustschin <agust@denx.de>
Add DDC & EDID support and use it to automatically select the native mode of
the attached monitor. This can be disabled by adding edid=0 as option
to the video-mode env. variable.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Anatolij Gustschin <agust@denx.de>
PLL1 on sun6i / sun8i also has a p factor which divides the clock by
2^p (to the power p). On sun6i the p factor is ignored, but on sun8i it is
used and we were setting it to 1, resulting in the CPU running at 504 MHz
instead of 1008 MHz, this commit fixes this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
After reboot, reset or even short power off, DRAM typically retains
the old stale data for some period of time (for this type of memory,
the bits of data are stored in slowly discharging capacitors).
The current sun6i/sun8i DRAM size detection logic, which is
inherited from the Allwinner code, relies on using a large magic
signature with the hope that it is unique enough and unlikely to
ever accidentally match this leftover garbage data in RAM. But
this approach is inherently unsafe, as can be demonstrated using
the following test program:
/***** A testcase for reproducing the problem ******/
void main(int argc, char *argv[])
{
size_t size, i;
uint32_t *buf;
/* Allocate the buffer */
if (argc < 2 || !(size = (size_t)atoi(argv[1]) * 1048576) ||
!(buf = malloc(size))) {
printf("Need buffer size in MiB as a cmdline argument\n");
exit(1);
}
/* Fill it with the Allwinner DRAM "magic" values */
for (i = 0; i < size / 4; i++)
buf[i] = 0xaa55aa55 + ((uintptr_t)&buf[i] / 4) % 64;
/* Try to reboot */
system("reboot");
/* And wait */
for (;;) {}
}
/***************************************************/
If this test program is run on the device (giving it a large
chunk of memory), then the DRAM size detection logic in u-boot
gets confused after reboot and fails to initialize DRAM properly.
A better approach is not to rely on luck and abstain from making
any assumptions about the properties of the leftover garbage
data in RAM. Instead just use a more reliable code for testing
whether two different addresses refer to the same memory location.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Based on the register / dram_para headers from the Allwinner u-boot / linux
sources + the init sequences from boot0.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The sun8i boot0 code fills the DRAM with a "random" pattern before comparing
it at different offsets to do columns, etc. detection. The sun6i boot0 code
does not do it, instead relying on the memory contents being random enough
to begin with for the memcmp to properly detect the wrap-around address, iow
it is working purely by chance. Since our sun6i dram code was modelled after
the boot0 code it contained the same issue.
This commit fixes this by filling the memory with a unique, distinct pattern.
The new mctl_mem_fill function this introduces is added as an inline helper
in dram.h, so that it can be shared with the sun8i dram code.
While at it move mctl_mem_matches to dram.h for re-use in sun8i too.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The await_completion helper is already copy pasted between the sun4i and sun6i
dram code, and we need it for sun8i too, so lets make it an inline helper in
dram.h, rather then adding yet another copy.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The sun8i dram code sometimes wants to enable sigma delta mode,
add a parameter to allow this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
sun8i (A23) introduces a new bus for communicating with the pmic, the rsb,
the rsb is also used to communicate with the pmic on the A80, and is
documented in the A80 user manual.
This commit adds support for this based on the rsb driver from the allwinner
u-boot sources.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The p2wi interface is only available on sun6i, adjust the gpio pinmux and
base address defines for it to reflect this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
On sun6i the SID is stored in the pmic, rather then in the SoC itself,
add a helper function to abstract this away.
This makes our MAC address generation code also work on sun6i.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The sunxi mmc controller has both an internal clock divider, as well as
the divider in the mod0-clk for the mmc controller.
The internal divider cannot be used, as it conflicts with the setting of
clock sampling phases which is done in the mod0-clk, so it must be set to
0 (divide by 1).
For some reason while the kernel has had this correct from day one, the
u-boot sunxi mmc code has been using a fixed mod0-clk and setting its
internal divider depending on the desired speed. This is something which
we've inherited from the original Allwinner u-boot sources, but while this
has been fixed in Allwinner's own u-boot code at least for the A23 and later
upstream u-boot was still doing this wrong.
This commit fixes this, thereby also fixing mmc support not working reliable
on the A23 (which seems more sensitive to this) and possible also fixes some
other sunxi mmc issues.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add a sunxi_get_ss_bonding_id() function, and use it to differentiate between
the A31s and the A31.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Switch to using hardware leveling for certain parameters on the EMIF
rather than using precalculated values. Doing this also means we have a
common place now between am437x and am335x for setting
emif_sdram_ref_ctrl with a value for the correct delay length.
Tested-by: Felipe Balbi <balbi@ti.com>
Tested-by: Tom Rini <trini@ti.com>
Signed-off-by: James Doublesin <doublesin@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Resynchronize memcpy/memset with kernel 3.17 and build them in
Thumb2 mode (unified syntax). Those assembler files can be built
and linked in ARM mode too, however when calling them from Thumb2
built code, the stack got corrupted and the copy did not succeed
(the exact details have not been traced back). However, the Linux
kernel builds those files in Thumb2 mode. Hence U-Boot should
build them in Thumb2 mode too when CONFIG_SYS_THUMB_BUILD is set.
To build the files without warning, some assembler instructions
had to be replaced with their UAL compliant variant (thanks
Jeroen for this input).
To build the file in Thumb2 mode the implicit-it=always option need
to be set to generate Thumb2 compliant IT instructions where needed.
We add this option to the general AFLAGS when building for Thumb2.
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Agner <stefan@agner.ch>
The low-level debugging functions are useful to debug the early boot
stage where the full UART driver is not available.
UniPhier SoCs need to initialize the UART port 0 to use this feature.
The initialization routine is called at the very entry of the
lowlevel_init().
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
For NAND boot on PH1-LD4, PH1-sLD8, and some other SoCs,
the output of the system bus is disabled by default.
It must be enabled by software to have access to the system bus.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
pci ports are used as root complex in Linux. So set this as default
in u-boot for keystone devices
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Part of DMM logic is reuse from commit
47a4bea6af ("ARM: omap4: Update sdram
setting for panda rev A6") Which broke SDP4430 with ES2.3 (uses old
DDR).
So, to maintain support for newer DDR used in Panda ES rev B3, we
should, in addition to the commit
675cc77a3a ("ARM:OMAP4+: panda-es: Support
Rev B3 Elpida DDR2 RAM"), DDR timings, also do DMM configuration
specific to Panda.
Signed-off-by: Nishanth Menon <nm@ti.com>
Commit 8bc347e2ec "ARM: bootm: Allow booting in secure mode on hyp capable
systems" added the capability to select nonsec vs sec mode boot via an
environment var.
There is a subtle gotcha with this functionality, which is that the PSCI nodes
are still created in the fdt (via armv7_update_dt->fdt_psci) even when booting
in secure mode. Which means that if the kernel is PSCI aware then it will fail
to boot because it will try and do PSCI from secure world, which won't work.
This likely didn't get noticed before because the original purpose was to
support booting the legacy linux-sunxi kernels which don't understand PSCI.
To fix expose boot_nonsec (renaming with armv7_ prefix) outside of bootm.c and
use from the virt-dt code.
As well as avoiding the creation of the PSCI nodes we should also avoid
reserving the secure RAM, so do so.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
This training code provides run-time adjustment of DDR PHY parameters
for stable DDR operation.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
enable this clock with the following:
clk_usb_otg_enable((void *)HSOTG_BASE_ADDR)
Signed-off-by: Steve Rae <srae@broadcom.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Add a board rev entry for the new model A+, and augment the board
rev error handling code to be a bit more verbose.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
There is currently a regression when using newer ARM64 compilers
for semihosting: the way long types are inferred from context
is no longer the same.
The semihosting runtime uses long and size_t, so use this
explicitly in the semihosting code and interface, and voila:
the code now works again.
Tested with aarch64-linux-gnu-gcc: Linaro GCC 4.9-2014.09.
Cc: Darwin Rambo <drambo@broadcom.com>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Mark Hambleton <mark.hambleton@arm.com>
Cc: Tom Rini <trini@ti.com>
Acked-by: Steve Rae <srae@broadcom.com>
Suggested-by: Mark Hambleton <mark.hambleton@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The semihosting code exposes internal file handle handling
functions to read(), open(), close() and get the length of
a certain file handle.
However the code using it is only interested in either
reading and entire named file into memory or getting the
file length of a file referred by name. No file handles
are used.
Thus make the file handle code internal to this file by
removing these functions from the semihosting header file
and staticize them.
This gives us some freedom to rearrange the semihosting
code without affecting the external interface.
Cc: Darwin Rambo <drambo@broadcom.com>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Mark Hambleton <mark.hambleton@arm.com>
Cc: Tom Rini <trini@ti.com>
Acked-by: Steve Rae <srae@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Not all exynos 5420 based devices with an LCD also have a parade LVDS
bridge. So make sure compilation doesn't break if CONFIG_LCD is enabled
and CONFIG_VIDEO_PARADE is not.
As a side-effect move the parade functions from the exynos system header
file to its own file.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Implement an API that can be used by drivers to allocate memory from a
pool that is mapped uncached. This is useful if drivers would otherwise
need to do extensive cache maintenance (or explicitly maintaining the
cache isn't safe).
The API is protected using the new CONFIG_SYS_NONCACHED_MEMORY setting.
Boards can set this to the size to be used for the non-cached area. The
area will typically be right below the malloc() area, but architectures
should take care of aligning the beginning and end of the area to honor
any mapping restrictions. Architectures must also ensure that mappings
established for this area do not overlap with the malloc() area (which
should remain cached for improved performance).
While the API is currently only implemented for ARM v7, it should be
generic enough to allow other architectures to implement it as well.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This controller was introduced on Tegra114 to handle XUSB pads. On
Tegra124 it is also used for PCIe and SATA pin muxing and PHY control.
Only the Tegra124 PCIe and SATA functionality is currently implemented,
with weak symbols on Tegra114.
Tegra20 and Tegra30 also provide weak symbols for these functions so
that drivers can use the same API irrespective of which SoC they're
being built for.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Implement the powergate API that allows various power partitions to be
power up and down.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This reset is required for PCIe and the corresponding ID therefore needs
to be defined. The enumeration value for this was properly defined on
some SoCs but not on others. Similarly, some contained it in the mapping
of peripheral IDs to clock IDs, other didn't. This patch defines it
consistently for all supported SoC generations.
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This function is required by PCIe and SATA. This patch implements it on
Tegra20, Tegra30 and Tegra124. It isn't implemented for Tegra114 because
it doesn't support PCIe or SATA.
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This converts all Tegra boards over to use driver model for I2C. The driver
is adjusted to use driver model and the following obsolete CONFIGs are
removed:
- CONFIG_SYS_I2C_INIT_BOARD
- CONFIG_I2C_MULTI_BUS
- CONFIG_SYS_MAX_I2C_BUS
- CONFIG_SYS_I2C_SPEED
- CONFIG_SYS_I2C
This has been tested on:
- trimslice (no I2C)
- beaver
- Jetson-TK1
It has not been tested on Tegra 114 as I don't have that board.
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
LS1 has 4 SMMUs for address translation of the masters. All the
SMMUs' stream IDs are 8-bit. The address translation depends on the
stream ID of the incoming transaction.
Each master has unique stream ID assigned to it and is configurable
through SCFG registers. The stream ID for the masters is identical
and share the same register field of STREAM ID registers.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The Central Security Unit (CSU) allows secure world software to
change the default access control policies of peripherals/bus
slaves, determining which bus masters may access them. This
allows peripherals to be separated into distinct security domains.
Combined with SMMU configuration of the system masters privileges,
these features provide protection against indirect unauthorized
access to data.
For now we configure all the peripheral access permissions as R/W.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Enable hypervisors utilizing the ARMv7 virtualization extension
on the LS1021A-QDS/TWR boards with the A7 core tile, we add the
required configuration variable.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds NAND boot support for LS1021AQDS board. SPL
framework is used. PBL initialize the internal RAM and copy
SPL to it, then SPL initialize DDR using SPD and copy u-boot
from NAND flash to DDR, finally SPL transfer control to u-boot.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds QSPI boot support for LS1021AQDS/TWR board.
The QSPI boot image need to be programmed into the QSPI flash
first. Then the booting will start from QSPI memory space.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds SD boot support for LS1021AQDS board. SPL
framework is used. PBL initialize the internal RAM and copy
SPL to it, then SPL initialize DDR using SPD and copy u-boot
from SD card to DDR, finally SPL transfer control to u-boot.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: Jason Jin <jason.jin@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The patch changes PCIe dts node status to 'disabled' if the
corresponding controller is disabled according to serdes protocol.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
After wakeup from deep sleep, Clear EPU registers as early as possible
to prevent from possible issue. It's also safe to clear at normal boot.
Signed-off-by: Chenhui Zhao <chenhui.zhao@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
R-Mobile and R-Car ARM SoCs use sh_mmcif as MMC host driver.
This adds arch-rmobile/mmc.h that defines mmcif_mmc_init().
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
stv0991 architecture support added. It contains the support for
following blocks
- Timer
- uart
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
[trini: Add arch/arm/cpu/armv7/Makefile hunk]
Signed-off-by: Tom Rini <trini@ti.com>
Some UniPhier boards are equipped with an expansion slot that
some optional SRAM/NOR-flash cards can be attached to. So, run-time
detection of the number of flash banks would be more user-friendly.
Until this commit, UniPhier boards have achieved this by (ab)using
board_flash_wp_on() because the boot failed if flash_size got zero.
Fortunately, this problem was solved by commit 70879a9256 (flash:
do not fail even if flash_size is zero).
Now it is possible to throw away such a tricky workaround. This
commit also enables CONFIG_SYS_MAX_FLASH_BANKS_DETECT for further
refactoring.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Detect the board revision early during boot, and print the decoded
model name.
Eventually, this information can be used for tasks such as:
- Allowing/preventing USB device mode; some models have a USB device on-
board so only host mode makes sense. Others connect the SoC directly
to the USB connector, so device-mode might make sense.
- The on-board USB hub/Ethernet requires different GPIOs to enable it,
although luckily the default appears to be fine so far.
- The compute module contains an on-board eMMC device, so we could store
the environment there. Other models use an SD card and so don't support
saving the environment (unless we store it in a file on the FAT boot
partition...)
Set $fdtfile based on this information. At present, the mainline Linux
kernel doesn't contain a separate DTB for most models, but I hope that
will change soon.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Correctly increment the base address of the freeze controller. And since
SYSMGR_FRZCTRL_VIOCTRL_SHIFT is not needed, remove it from the include file.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Vince Bridgers <vbridger@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Marek Vasut <marex@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
socfpga_scan_manager structure was missing a data member.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Vince Bridgers <vbridger@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Marek Vasut <marex@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Re-map NAND&I2C boot-device to the "normal" NAND boot-device.
Otherwise the SPL boot IF can't handle this device correctly.
Somehow booting with Hynix 4GBit NAND H27U4G8 on Siemens
Draco leads to this boot-device passed to SPL from the BootROM.
With this change, Draco boots just fine into main U-Boot.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Roger Meier <r.meier@siemens.com>
Cc: Samuel Egli <samuel.egli@siemens.com>
The infomation of module control register for R-Car ARM SoC (r8a7790, r8a7791,
r8a7793 and r8a7794) are almost the same, they can be combined into one
structure. This provides structure that summarizes infomation of module control
register and default register values.
And this structure is the module control use of the kernel at boot time.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This adds infomation of bits for module control register. This is used
to control modules on ARM R-Car SoCs.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This addes macro for set and clear bit control for module control register.
This is used when user want to disable the function of the devices
corresponding to register.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Control macro of mstp is common in R-Car ARM SoC (r8a7790, r8a7791,
r8a7793 and r8a7794). This moves these to arch-rmobile/rcar-mstp.h
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Module control registers of R-Car ARM SoC (r8a7790, r8a7791, r8a7793 and
r8a7794) are same address. This moves these to header file of SoC.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
just add a few ifdefs around because this
device is very similar to dra7xxx.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
expose those two definitions so they can be
used by another board which we're adding in upcoming
patches.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Those regulators don't have any coupling with
what they supply, so remove the suffixes in order
to not confuse anybody.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
As checkpatch complaines about these camel-case defines, lets change
them to only use upper-case characters.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Jon Nettleton <jon.nettleton@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
If CONFIG_OF_CONTROL is enabled, lib/fdtdec.c is compiled.
It includes <asm/gpio.h> and then <asm/gpio.h> includes
<asm/arch/gpio.h>. Consequently, all the SoCs that enable
CONFIG_OF_CONTROL must have <asm/arch/gpio.h> even if they do not
support GPIO.
In the first place, GPIO has nothing to do with OF_CONTROL.
It is wrong that lib/fdtdec.c includes GPIO functions; it should
be split into two files, FDT-common things and GPIO things.
It is, however, a pretty big work to fix that correctly.
This is a compromised commit to add a dummy <asm/arch/gpio.h>
to support OF_CONTROL for UniPhier platform. This dummy header
will be removed after FDT-GPIO stuff is fixed correctly.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Merge struct s3c2410_nand and struct s3c2440_nand into one unified
struct s3c24x0_nand. While at it, fix up and rename the functions
to retrieve the NAND base address and fix up the s3c NAND driver to
reflect this change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Add simplefb support, note this depends on the kernel having support for
the clocks property which has recently been added to the simplefb devicetree
binding.
Signed-off-by: Luc Verhaegen <libv@skynet.be>
[hdegoede@redhat.com: Use pre-populated simplefb node under /chosen as
disussed on the devicetree list]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>.
This adds a fixed mode hdmi driver for the sunxi platform. The fixed
mode is a relatively safe 1024x768, more complete EDID handling is
currently not provided. Only HDMI is supported today.
This code is enabled when HPD detects an attached monitor.
Current config is such that 8MB is shaved off at the top of the RAM.
This avoids several memory handling issues, most significant is the fact
that on linux on ARM you are not allowed to remap known RAM as IO. A
clued in display driver will be able to recycle this reserved RAM in
future though.
cfbconsole was chosen as it provides the most important functionality: a
working u-boot console, allowing for the debugging of certain issues
without the need for a UART.
Signed-off-by: Luc Verhaegen <libv@skynet.be>
[hdegoede@redhat.com: Major cleanups and some small bugfixes]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
This is a preparation patch for adding support for HDMI out.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The data sheet just calls it DRAM_CLK_REG, and on sun6i we've both a
dram_clk_cfg and dram_clk_gate, and the sun4i reg matches dram_clk_gate on
sun6i, so name it the same on sun4i.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
SCFG_SCFGREVCR is SCFG bit reverse register. This register
must be written with 0xFFFFFFFF before writing to any other
SCFG register. Then other SCFG register could be written in
big-endian mode.
Address: 157_0000h base + 200h offset = 157_0200h
Bit 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15|16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
W/R SCFGREV
Reset 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0-31
SCFGREV SCFG Bit Reverse Control Filed
32'h 0000_0000 - No bit reverse is applied
32'h FFFF_FFFF - Bit reverse is applied; so 31:0 will be stored/read as
0:31
This patch removes the bit reversing for SCFG registers in
u-boot. It will be implemented through PBI commands in RCW
.pbi
write 0x570200, 0xffffffff
.end
So other SCFG register could be written in big-endian mode
in u-boot or kernel directly.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Disable the snoop for slave interface 0, 1 and 2
to avoid the interleaving on the CCI400 BUS.
Signed-off-by: Jason Jin <Jason.Jin@freescale.com>
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Define USB configs for LS1021XA such as CONFIG_SYS_FSL_USB1_ADDR,
CONFIG_USB_MAX_CONTROLLER_COUNT
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add api to check and enable pll3 as required
for thermal sensor driver.
Signed-off-by: Ye.Li <B37916@freescale.com>
Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
Add driver model support while retaining the existing legacy code. This
allows the driver to support boards that have converted to driver model
as well as those that have not.
Signed-off-by: Simon Glass <sjg@chromium.org>
These boards all have the same GPIO arrangement, so add some common platform
data that can be used by all boards. Remove the configs which are no longer
required.
Signed-off-by: Simon Glass <sjg@chromium.org>
Modify this driver to support driver model, with platform data required to
determine the GPIOs that it controls.
Signed-off-by: Simon Glass <sjg@chromium.org>
CONFIG_CPU_ARM926EJS was introduced into Kconfig by commit 2e07c249a6
(kconfig: arm: introduce symbol for ARM CPUs).
This commit removes all the defines of CONFIG_ARM926EJS and replaces
the only reference in arch/arm/lib/cache.c with CONFIG_CPU_ARM926EJS.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
CONFIG_CPU_ARM920T was introduced into Kconfig by commit 2e07c249a6
(kconfig: arm: introduce symbol for ARM CPUs).
This commit removes all the defines of CONFIG_ARM920T and replaces the
only reference in drivers/usb/host/ohci-hcd.c with CONFIG_CPU_ARM920T.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Some (not all) of ARMv7 boards define CONFIG_ARMV7, which is useless.
Besides, it is never referenced.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Move MX5 specific set_chipselect_size function into generic i.MX part,
such that MX6 based boards are able to use this function as well.
While doing this the iomuxc gpr member needed to be consolidated between
MX5 and MX6.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
There are 8 SCFG_SPARECR registers in SCFG memory block, not one.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
ls1021 is arm-core and support qe which is u-qe.
add u-qe init for arm board.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
[York Sun: Fix compiling error caused by u_qe_init()]
Reviewed-by: York Sun <yorksun@freescale.com>
The code for this board supports following features:
- Boot media support: NAND flash/SD card/SPI flash
- Support LCD display
- Support ethernet
- Support USB mass storage
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
add support for using spl code on at91sam9260 and at91sam9g45
based boards.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Bo Shen <voice.shen@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
[adopt Bo's change in spl.c]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
This change adds support for enabling the USB host features of the board.
This includes the USB3503A hub and the SMC LAN9730 ethernet controller
as well.
Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Enable/disable the usb host phy on the odroid U/X2 boards which are based
on the Exynos4412 SOC.
Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
As per Exynos5800 UM ver 0.00 section 17.13.2.1
CONCONTROL register bit 3 [update_mode], Exynos5800 does not
support the PHY initiated update. And it is recommanded to
set this field to 1'b1 during initialization. This patch sets this bit.
Applying MC-initiated mode makes DDL tracking ON, that helps in
compensate MIF voltage variation.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch intends to add a new proid for Exynos5800 which is a
variant of Exynos5420. Product id for Exynos5800 is 0x5422.
Both Exynos5420 and Exynos5800 are pin to pin compitable. This
gives us an advantage of reusing Exynos5420 clock, pinmux, memory
and other settings.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add pinmux settings, implement board_ehci_hcd_init, board_usb_phy_mode
There are two usb port on mx6slevk board:
1. otg port
2. host port
The following are the connection between usb controller and board usb
interface, host port has not ID pin set:
otg1 core <---> board otg port
otg2 core <---> board host port
In order to make host port work, board_usb_phy_mode return USB_INIT_HOST
to let host port work in host mode.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ye Li <B37916@freescale.com>
Add support for the 2 ehci controllers found on the sun6i (A31) soc.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Marek Vasut <marex@denx.de>
Add full support for dram initialization, using a fixed clock and autodetection
of the memory organization (numbers of channels, bus-width, etc.).
This is based on dram_sun6i.c and dram.h from u-boot in the Allwinner A31 SDK,
extended with extra initialization sequences and the autodetect algorithm
from boot0.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add clock_init_safe and clockset_pll5 functions, as these are needed for
SPL support resp. DRAM init (which is needed for SPL too).
Also add some extra clock register constant defines.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The A31 uses a new push-pull two wire interface, which features higher
transfer speeds (upto 6 MHz) in theory. While the hardware can burst 8
bytes each time, this driver will only see very little use and thus is
limited to single byte transmission only.
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
size_t is the canonical type to represent variables that contain a size.
Use it instead of signed integer. Physical addresses can be larger than
32-bit, so use a more appropriate type for them as well. phys_addr_t is
a type that is 32-bit on systems that use 32-bit addresses and 64-bit if
the system is 64-bit or uses a form of physical address extension to use
a larger address space on 32-bit systems. Using these types the same API
can be implemented on a wider range of systems.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The function sg_set_pinsel is useful for switching I/O pins
but it can be only used in C code. This commit adds a simple
macro that is available in asm code.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Support EHCI host driver used on Panasonic UniPhier platform.
Since Device Tree is not supported on UniPhier yet, the base address
of USB cores are passed from board files (platdevice.c).
TODO for me:
Move the base address to device trees.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Marek Vasut <marex@denx.de>
This commit adds register defines of MIO (Media I/O) block
of UniPhier platform. This file is necessary to control
the reset signals of the USB cores.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
R-Car SoCs of rmobile have same IP of rcar-i2c, and have same address.
This moves rcar-i2c of the address defined to rcar-base.h as common header of
R-Car SoCs.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
R-Car SoCs of rmobile have same IP of sh-i2c, and have same address.
This moves sh-i2c of the address defined to rcar-base.h as common header of
R-Car SoCs, and headers of each SoCs.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Renesas R8A7793 is CPU with Cortex-A15. This supports the basic register
definition and GPIO and framework of PFC.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
This function will be needed by the upcoming Designware master SPI
driver. As the SPI master controller is held in reset by the current
Preloader implementation. So we need to release the reset for the
driver to communicate with the controller.
This function is called from arch_early_init_r() if the SPI
driver is enabled.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Vince Bridgers <vbridger@altera.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Pavel Machek <pavel@denx.de>
This patch includes the latest DT sources for socfpga from the current
Linux kernel. And enables CONFIG_OF_CONTROL for the new build target
"socfpga_socrates" (the EBV SoCrates board) to make use of this new DT
support.
Until this patch, the only SoCFPGA U-Boot target in mainline is
"socfpga_cyclone5". This build target is not (yet) changed to support
DT. So nothing changes for this target. Even though the long-term
goal should be to move all SoCFPGA targets over to DT.
One of the reasons to enable DT support in SoCFPGA is, that I need to
support multiple different SPI controllers for this platform. This is
the QSPI Cadence controller and the Designware SPI master controller.
Both are implemented in the SoCFPGA. And enabling both controllers is
only possible by using the new driver model (DM). The DM SPI code
only supports DT based probing. So it was easier to move SoCFPGA to
DT than to add the (deprecated) platform-data based probing to the
DM SPI suport.
Note that the image with the dtb embedded is u-boot-dtb.img. This needs
to be used now for those DT enabled boards instead of u-boot.img.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Vince Bridgers <vbridger@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Pavel Machek <pavel@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Current get_board_rev() function returns a hard coded value which is
obviously incorrect for the majority of boards.
Allow boards to provide a correct implementation by making this
function weak.
In addition open code the trivial and useless BOARD_REV_ID define and
adjust the comment.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tom Rini <trini@ti.com>
The Keystone2 Lamar SoC uses the same keystone net driver.
This patch adds opportunity to use it by K2L SoCs.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Keystone2 Lamar SoC uses the same keystone SerDes driver.
All Keystone2 EVM boards currently use SerDes driver, so move
CONFIG_TI_KEYSTONE_SERDES to common configuration file.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
The Keystone2 Lamar SoC uses the same keystone navigator.
Move queue numbers to common hardware file, as all Keystone2 SoCs
have the same ones.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
With driver model we will have access to a bank pointer, so we want to
use it rather than converting back to a number, and then back to a
bank pointer. Add functions to provide this feature.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Mostly automatic with:
sed -i -e 's/CONFIG_\(SUN[45678]I\)/CONFIG_MACH_\1/g' $(git grep -l CONFIG_SUN[45678]I)
followed by removing the relevant #defines from include/configs/sun?i.h by
hand.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The change of the CPU frequency is waited for until PLL0ST of the PLLECR is
set to 1.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
On mx6 sabreauto board, there are two USB ports:
0: OTG
1: HOST
The EHCI driver is enabled for this board, but the IOMUX and VBUS power
control is not implemented, which cause both USB port failed to work.
This patch fix the problem by adding the board support codes.
Since the power control uses the GPIO pin from port expander MAX7310,
the PCA953X driver is enabled for accessing the MAX7310.
The ID pin of OTG Port needs to configure the GPR1 bit 13 for selecting
its daisy chain. Add a new function "imx_iomux_set_gpr_register" to
handle GPR register setting.
Signed-off-by: Ye.Li <B37916@freescale.com>
[1] arch/arm/include/asm/arch-at91/at91_shdwn.h
The top9000 was the last board to use this header file.
It was removed by commit d58a9451e7 (ppc/arm: zap EMK boards).
[2] board/matrix_vision/common/*
Some Matrix Vision boards were dropped by commit e7a565638a
(powerpc: mpc83xx: remove board support for MERGERBOX and MVBLM7)
and commit af55e35d33
(powerpc: mpc5xxx: remove board support for MVBC_P and MVSMR).
Since then these files have been unused.
[3] include/usb/omap1510_udc.h
The omap5912osk was the last board to use this header file.
It was removed by commit 62d636aa2a
(omap: remove omap5912osk board support).
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-By: Wolfgang Denk <wd@denx.de>
This patch adds extra gpio part addresses to exynos4
and exynos4x12_gpio_data arrays, which are required
since the gpio enum lists are linear
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
After remove the offsets in Exynos4/4x12 gpio enums,
an additional gpio base addresses are required.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
