powerpc: mpc5xxx: remove board support for MVBC_P and MVSMR

These boards have been orphaned for more than 6 months.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
This commit is contained in:
Masahiro Yamada 2014-09-29 01:38:01 +09:00 committed by Tom Rini
parent e7a565638a
commit af55e35d33
26 changed files with 2 additions and 1848 deletions

View file

@ -97,12 +97,6 @@ config TARGET_MUCMC52
config TARGET_UC101
bool "Support uc101"
config TARGET_MVBC_P
bool "Support MVBC_P"
config TARGET_MVSMR
bool "Support MVSMR"
config TARGET_PCM030
bool "Support pcm030"
@ -139,8 +133,6 @@ source "board/jupiter/Kconfig"
source "board/manroland/hmi1001/Kconfig"
source "board/manroland/mucmc52/Kconfig"
source "board/manroland/uc101/Kconfig"
source "board/matrix_vision/mvbc_p/Kconfig"
source "board/matrix_vision/mvsmr/Kconfig"
source "board/mcc200/Kconfig"
source "board/motionpro/Kconfig"
source "board/munices/Kconfig"

View file

@ -1,12 +0,0 @@
if TARGET_MVBC_P
config SYS_BOARD
default "mvbc_p"
config SYS_VENDOR
default "matrix_vision"
config SYS_CONFIG_NAME
default "MVBC_P"
endif

View file

@ -1,6 +0,0 @@
MVBC_P BOARD
#M: Andre Schwarz <andre.schwarz@matrix-vision.de>
S: Orphan (since 2014-03)
F: board/matrix_vision/mvbc_p/
F: include/configs/MVBC_P.h
F: configs/MVBC_P_defconfig

View file

@ -1,11 +0,0 @@
#
# (C) Copyright 2003
# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
#
# (C) Copyright 2004-2008
# Matrix-Vision GmbH, info@matrix-vision.de
#
# SPDX-License-Identifier: GPL-2.0+
#
obj-y := mvbc_p.o fpga.o

View file

@ -1,73 +0,0 @@
Matrix Vision mvBlueCOUGAR-P (mvBC-P)
-------------------------------------
1. Board Description
The mvBC-P is a 70x40x40mm multi board gigabit ethernet network camera
with main focus on GigEVision protocol in combination with local image
preprocessing.
Power Supply is either VDC 48V or Pover over Ethernet (PoE).
2 System Components
2.1 CPU
Freescale MPC5200B CPU running at 400MHz core and 133MHz XLB/IPB.
64MB SDRAM @ 133MHz.
8 MByte Nor Flash on local bus.
1 serial ports. Console running on ttyS0 @ 115200 8N1.
2.2 PCI
PCI clock fixed at 66MHz. Arbitration inside FPGA.
Intel GD82541ER network MAC/PHY and FPGA connected.
2.3 FPGA
Altera Cyclone-II EP2C8 with PCI DMA engine.
Connects to Matrix Vision specific CCD/CMOS sensor interface.
Utilizes 64MB Nand Flash.
2.3.1 I/O @ FPGA
2 Outputs : photo coupler
2 Inputs : photo coupler
2.4 I2C
LM75 @ 0x90 for temperature monitoring.
EEPROM @ 0xA0 for vendor specifics.
image sensor interface (slave addresses depend on sensor)
3 Flash layout.
reset vector is 0x00000100, i.e. "LOWBOOT".
FF800000 u-boot
FF840000 u-boot script image
FF850000 redundant u-boot script image
FF860000 FPGA raw bit file
FF8A0000 tbd.
FF900000 root FS
FFC00000 kernel
FFFC0000 device tree blob
FFFD0000 redundant device tree blob
FFFE0000 environment
FFFF0000 redundant environment
mtd partitions are propagated to linux kernel via device tree blob.
4 Booting
On startup the bootscript @ FF840000 is executed. This script can be
exchanged easily. Default boot mode is "boot from flash", i.e. system
works stand-alone.
This behaviour depends on some environment variables :
"netboot" : yes ->try dhcp/bootp and boot from network.
A "dhcp_client_id" and "dhcp_vendor-class-identifier" can be used for
DHCP server configuration, e.g. to provide different images to
different devices.
During netboot the system tries to get 3 image files:
1. Kernel - name + data is given during BOOTP.
2. Initrd - name is stored in "initrd_name"
3. device tree blob - name is stored in "dtb_name"
Fallback files are the flash versions.

View file

@ -1,157 +0,0 @@
/*
* (C) Copyright 2002
* Rich Ireland, Enterasys Networks, rireland@enterasys.com.
* Keith Outwater, keith_outwater@mvis.com.
*
* (C) Copyright 2008
* Andre Schwarz, Matrix Vision GmbH, andre.schwarz@matrix-vision.de
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <ACEX1K.h>
#include <command.h>
#include "fpga.h"
#include "mvbc_p.h"
#ifdef FPGA_DEBUG
#define fpga_debug(fmt, args...) printf("%s: "fmt, __func__, ##args)
#else
#define fpga_debug(fmt, args...)
#endif
Altera_CYC2_Passive_Serial_fns altera_fns = {
fpga_null_fn,
fpga_config_fn,
fpga_status_fn,
fpga_done_fn,
fpga_wr_fn,
fpga_null_fn,
fpga_null_fn,
};
Altera_desc cyclone2 = {
Altera_CYC2,
passive_serial,
Altera_EP2C8_SIZE,
(void *) &altera_fns,
NULL,
};
DECLARE_GLOBAL_DATA_PTR;
int mvbc_p_init_fpga(void)
{
fpga_debug("Initialize FPGA interface\n");
fpga_init();
fpga_add(fpga_altera, &cyclone2);
fpga_config_fn(0, 1, 0);
udelay(60);
return 1;
}
int fpga_null_fn(int cookie)
{
return 0;
}
int fpga_config_fn(int assert, int flush, int cookie)
{
struct mpc5xxx_gpio *gpio = (struct mpc5xxx_gpio*)MPC5XXX_GPIO;
u32 dvo = gpio->simple_dvo;
fpga_debug("SET config : %s\n", assert ? "low" : "high");
if (assert)
dvo |= FPGA_CONFIG;
else
dvo &= ~FPGA_CONFIG;
if (flush)
gpio->simple_dvo = dvo;
return assert;
}
int fpga_done_fn(int cookie)
{
struct mpc5xxx_gpio *gpio = (struct mpc5xxx_gpio*)MPC5XXX_GPIO;
int result = 0;
udelay(10);
fpga_debug("CONF_DONE check ... ");
if (gpio->simple_ival & FPGA_CONF_DONE) {
fpga_debug("high\n");
result = 1;
} else
fpga_debug("low\n");
return result;
}
int fpga_status_fn(int cookie)
{
struct mpc5xxx_gpio *gpio = (struct mpc5xxx_gpio*)MPC5XXX_GPIO;
int result = 0;
fpga_debug("STATUS check ... ");
if (gpio->sint_ival & FPGA_STATUS) {
fpga_debug("high\n");
result = 1;
} else
fpga_debug("low\n");
return result;
}
int fpga_clk_fn(int assert_clk, int flush, int cookie)
{
struct mpc5xxx_gpio *gpio = (struct mpc5xxx_gpio*)MPC5XXX_GPIO;
u32 dvo = gpio->simple_dvo;
fpga_debug("CLOCK %s\n", assert_clk ? "high" : "low");
if (assert_clk)
dvo |= FPGA_CCLK;
else
dvo &= ~FPGA_CCLK;
if (flush)
gpio->simple_dvo = dvo;
return assert_clk;
}
static inline int _write_fpga(u8 val)
{
int i;
struct mpc5xxx_gpio *gpio = (struct mpc5xxx_gpio*)MPC5XXX_GPIO;
u32 dvo = gpio->simple_dvo;
for (i=0; i<8; i++) {
dvo &= ~FPGA_CCLK;
gpio->simple_dvo = dvo;
dvo &= ~FPGA_DIN;
if (val & 1)
dvo |= FPGA_DIN;
gpio->simple_dvo = dvo;
dvo |= FPGA_CCLK;
gpio->simple_dvo = dvo;
val >>= 1;
}
return 0;
}
int fpga_wr_fn(const void *buf, size_t len, int flush, int cookie)
{
unsigned char *data = (unsigned char *) buf;
int i;
fpga_debug("fpga_wr: buf %p / size %d\n", buf, len);
for (i = 0; i < len; i++)
_write_fpga(data[i]);
fpga_debug("\n");
return FPGA_SUCCESS;
}

View file

@ -1,17 +0,0 @@
/*
* (C) Copyright 2002
* Rich Ireland, Enterasys Networks, rireland@enterasys.com.
* Keith Outwater, keith_outwater@mvis.com.
*
* SPDX-License-Identifier: GPL-2.0+
*/
extern int mvbc_p_init_fpga(void);
extern int fpga_pgm_fn(int assert_pgm, int flush, int cookie);
extern int fpga_status_fn(int cookie);
extern int fpga_config_fn(int assert, int flush, int cookie);
extern int fpga_done_fn(int cookie);
extern int fpga_clk_fn(int assert_clk, int flush, int cookie);
extern int fpga_wr_fn(const void *buf, size_t len, int flush, int cookie);
extern int fpga_null_fn(int cookie);

View file

@ -1,255 +0,0 @@
/*
* (C) Copyright 2003
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* (C) Copyright 2004
* Mark Jonas, Freescale Semiconductor, mark.jonas@motorola.com.
*
* (C) Copyright 2005-2007
* Andre Schwarz, Matrix Vision GmbH, andre.schwarz@matrix-vision.de
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <mpc5xxx.h>
#include <malloc.h>
#include <pci.h>
#include <i2c.h>
#include <fpga.h>
#include <environment.h>
#include <fdt_support.h>
#include <netdev.h>
#include <asm/io.h>
#include "fpga.h"
#include "mvbc_p.h"
#include "../common/mv_common.h"
#define SDRAM_MODE 0x00CD0000
#define SDRAM_CONTROL 0x504F0000
#define SDRAM_CONFIG1 0xD2322800
#define SDRAM_CONFIG2 0x8AD70000
DECLARE_GLOBAL_DATA_PTR;
static void sdram_start (int hi_addr)
{
long hi_bit = hi_addr ? 0x01000000 : 0;
/* unlock mode register */
out_be32((u32*)MPC5XXX_SDRAM_CTRL, SDRAM_CONTROL | 0x80000000 | hi_bit);
/* precharge all banks */
out_be32((u32*)MPC5XXX_SDRAM_CTRL, SDRAM_CONTROL | 0x80000002 | hi_bit);
/* precharge all banks */
out_be32((u32*)MPC5XXX_SDRAM_CTRL, SDRAM_CONTROL | 0x80000002 | hi_bit);
/* auto refresh */
out_be32((u32*)MPC5XXX_SDRAM_CTRL, SDRAM_CONTROL | 0x80000004 | hi_bit);
/* set mode register */
out_be32((u32*)MPC5XXX_SDRAM_MODE, SDRAM_MODE);
/* normal operation */
out_be32((u32*)MPC5XXX_SDRAM_CTRL, SDRAM_CONTROL | hi_bit);
}
phys_addr_t initdram (int board_type)
{
ulong dramsize = 0;
ulong test1,
test2;
/* setup SDRAM chip selects */
out_be32((u32*)MPC5XXX_SDRAM_CS0CFG, 0x0000001e);
/* setup config registers */
out_be32((u32*)MPC5XXX_SDRAM_CONFIG1, SDRAM_CONFIG1);
out_be32((u32*)MPC5XXX_SDRAM_CONFIG2, SDRAM_CONFIG2);
/* find RAM size using SDRAM CS0 only */
sdram_start(0);
test1 = get_ram_size((long *)CONFIG_SYS_SDRAM_BASE, 0x80000000);
sdram_start(1);
test2 = get_ram_size((long *)CONFIG_SYS_SDRAM_BASE, 0x80000000);
if (test1 > test2) {
sdram_start(0);
dramsize = test1;
} else
dramsize = test2;
if (dramsize < (1 << 20))
dramsize = 0;
if (dramsize > 0)
out_be32((u32*)MPC5XXX_SDRAM_CS0CFG, 0x13 +
__builtin_ffs(dramsize >> 20) - 1);
else
out_be32((u32*)MPC5XXX_SDRAM_CS0CFG, 0);
return dramsize;
}
void mvbc_init_gpio(void)
{
struct mpc5xxx_gpio *gpio = (struct mpc5xxx_gpio*)MPC5XXX_GPIO;
printf("Ports : 0x%08x\n", gpio->port_config);
printf("PORCFG: 0x%08lx\n", *(vu_long*)MPC5XXX_CDM_PORCFG);
out_be32(&gpio->simple_ddr, SIMPLE_DDR);
out_be32(&gpio->simple_dvo, SIMPLE_DVO);
out_be32(&gpio->simple_ode, SIMPLE_ODE);
out_be32(&gpio->simple_gpioe, SIMPLE_GPIOEN);
out_8(&gpio->sint_ode, SINT_ODE);
out_8(&gpio->sint_ddr, SINT_DDR);
out_8(&gpio->sint_dvo, SINT_DVO);
out_8(&gpio->sint_inten, SINT_INTEN);
out_be16(&gpio->sint_itype, SINT_ITYPE);
out_8(&gpio->sint_gpioe, SINT_GPIOEN);
out_8((u8*)MPC5XXX_WU_GPIO_ODE, WKUP_ODE);
out_8((u8*)MPC5XXX_WU_GPIO_DIR, WKUP_DIR);
out_8((u8*)MPC5XXX_WU_GPIO_DATA_O, WKUP_DO);
out_8((u8*)MPC5XXX_WU_GPIO_ENABLE, WKUP_EN);
printf("simple_gpioe: 0x%08x\n", gpio->simple_gpioe);
printf("sint_gpioe : 0x%08x\n", gpio->sint_gpioe);
}
int misc_init_r(void)
{
char *s = getenv("reset_env");
if (!s) {
if (in_8((u8*)MPC5XXX_WU_GPIO_DATA_I) & MPC5XXX_GPIO_WKUP_6)
return 0;
udelay(50000);
if (in_8((u8*)MPC5XXX_WU_GPIO_DATA_I) & MPC5XXX_GPIO_WKUP_6)
return 0;
udelay(50000);
if (in_8((u8*)MPC5XXX_WU_GPIO_DATA_I) & MPC5XXX_GPIO_WKUP_6)
return 0;
}
printf(" === FACTORY RESET ===\n");
mv_reset_environment();
saveenv();
return -1;
}
int checkboard(void)
{
mvbc_init_gpio();
printf("Board: Matrix Vision mvBlueCOUGAR-P\n");
return 0;
}
void flash_preinit(void)
{
/*
* Now, when we are in RAM, enable flash write
* access for detection process.
* Note that CS_BOOT cannot be cleared when
* executing in flash.
*/
clrbits_be32((u32*)MPC5XXX_BOOTCS_CFG, 0x1);
}
void flash_afterinit(ulong size)
{
out_be32((u32*)MPC5XXX_BOOTCS_START, START_REG(CONFIG_SYS_BOOTCS_START |
size));
out_be32((u32*)MPC5XXX_CS0_START, START_REG(CONFIG_SYS_BOOTCS_START |
size));
out_be32((u32*)MPC5XXX_BOOTCS_STOP, STOP_REG(CONFIG_SYS_BOOTCS_START | size,
size));
out_be32((u32*)MPC5XXX_CS0_STOP, STOP_REG(CONFIG_SYS_BOOTCS_START | size,
size));
}
void pci_mvbc_fixup_irq(struct pci_controller *hose, pci_dev_t dev)
{
unsigned char line = 0xff;
char *s = getenv("pci_latency");
u32 base;
u8 val = 0;
if (s)
val = simple_strtoul(s, NULL, 16);
if (PCI_BUS(dev) == 0) {
switch (PCI_DEV (dev)) {
case 0xa: /* FPGA */
line = 3;
pci_hose_read_config_dword(hose, dev, PCI_BASE_ADDRESS_0, &base);
printf("found FPGA - enable arbitration\n");
writel(0x03, (u32*)(base + 0x80c0));
writel(0xf0, (u32*)(base + 0x8080));
if (val)
pci_hose_write_config_byte(hose, dev, PCI_LATENCY_TIMER, val);
break;
case 0xb: /* LAN */
line = 2;
if (val)
pci_hose_write_config_byte(hose, dev, PCI_LATENCY_TIMER, val);
break;
case 0x1a:
break;
default:
printf ("***pci_scan: illegal dev = 0x%08x\n", PCI_DEV (dev));
break;
}
pci_hose_write_config_byte(hose, dev, PCI_INTERRUPT_LINE, line);
}
}
struct pci_controller hose = {
fixup_irq:pci_mvbc_fixup_irq
};
extern void pci_mpc5xxx_init(struct pci_controller *);
void pci_init_board(void)
{
mvbc_p_init_fpga();
mv_load_fpga();
pci_mpc5xxx_init(&hose);
}
void show_boot_progress(int val)
{
struct mpc5xxx_gpio *gpio = (struct mpc5xxx_gpio*)MPC5XXX_GPIO;
switch(val) {
case BOOTSTAGE_ID_START: /* FPGA ok */
setbits_be32(&gpio->simple_dvo, LED_G0);
break;
case BOOTSTAGE_ID_NET_ETH_INIT:
setbits_be32(&gpio->simple_dvo, LED_G1);
break;
case BOOTSTAGE_ID_COPY_RAMDISK:
setbits_be32(&gpio->simple_dvo, LED_Y);
break;
case BOOTSTAGE_ID_RUN_OS:
setbits_be32(&gpio->simple_dvo, LED_R);
break;
default:
break;
}
}
void ft_board_setup(void *blob, bd_t *bd)
{
ft_cpu_setup(blob, bd);
}
int board_eth_init(bd_t *bis)
{
cpu_eth_init(bis); /* Built in FEC comes first */
return pci_eth_init(bis);
}

View file

@ -1,43 +0,0 @@
#ifndef __MVBC_H__
#define __MVBC_H__
#define LED_G0 MPC5XXX_GPIO_SIMPLE_PSC2_0
#define LED_G1 MPC5XXX_GPIO_SIMPLE_PSC2_1
#define LED_Y MPC5XXX_GPIO_SIMPLE_PSC2_2
#define LED_R MPC5XXX_GPIO_SIMPLE_PSC2_3
#define ARB_X_EN MPC5XXX_GPIO_WKUP_PSC2_4
#define FPGA_DIN MPC5XXX_GPIO_SIMPLE_PSC3_0
#define FPGA_CCLK MPC5XXX_GPIO_SIMPLE_PSC3_1
#define FPGA_CONF_DONE MPC5XXX_GPIO_SIMPLE_PSC3_2
#define FPGA_CONFIG MPC5XXX_GPIO_SIMPLE_PSC3_3
#define FPGA_STATUS MPC5XXX_GPIO_SINT_PSC3_4
#define MAN_RST MPC5XXX_GPIO_WKUP_PSC6_0
#define WD_TS MPC5XXX_GPIO_WKUP_PSC6_1
#define WD_WDI MPC5XXX_GPIO_SIMPLE_PSC6_2
#define COP_PRESENT MPC5XXX_GPIO_SIMPLE_PSC6_3
#define FACT_RST MPC5XXX_GPIO_WKUP_6
#define FLASH_RBY MPC5XXX_GPIO_WKUP_7
#define SIMPLE_DDR (LED_G0 | LED_G1 | LED_Y | LED_R | \
FPGA_DIN | FPGA_CCLK | FPGA_CONFIG | WD_WDI)
#define SIMPLE_DVO (FPGA_CONFIG)
#define SIMPLE_ODE (FPGA_CONFIG | LED_G0 | LED_G1 | LED_Y | LED_R)
#define SIMPLE_GPIOEN (LED_G0 | LED_G1 | LED_Y | LED_R | \
FPGA_DIN | FPGA_CCLK | FPGA_CONF_DONE | FPGA_CONFIG |\
WD_WDI | COP_PRESENT)
#define SINT_ODE 0
#define SINT_DDR 0
#define SINT_DVO 0
#define SINT_INTEN 0
#define SINT_ITYPE 0
#define SINT_GPIOEN (FPGA_STATUS)
#define WKUP_ODE (MAN_RST)
#define WKUP_DIR (ARB_X_EN|MAN_RST|WD_TS)
#define WKUP_DO (ARB_X_EN|MAN_RST|WD_TS)
#define WKUP_EN (ARB_X_EN|MAN_RST|WD_TS|FACT_RST|FLASH_RBY)
#endif

View file

@ -1,48 +0,0 @@
echo
echo "==== running autoscript ===="
echo
setenv bootdtb bootm \${kernel_boot} \${mv_initrd_addr_ram} \${mv_dtb_addr_ram}
setenv ramkernel setenv kernel_boot \${loadaddr}
setenv flashkernel setenv kernel_boot \${mv_kernel_addr}
setenv cpird cp \${mv_initrd_addr} \${mv_initrd_addr_ram} \${mv_initrd_length}
setenv bootfromflash run flashkernel cpird ramparam addcons e1000para addprofile bootdtb
setenv getdtb tftp \${mv_dtb_addr_ram} \${dtb_name}
setenv cpdtb cp \${mv_dtb_addr} \${mv_dtb_addr_ram} 0x2000
setenv rundtb fdt addr \${mv_dtb_addr_ram}\;fdt boardsetup
setenv bootfromnet tftp \${mv_initrd_addr_ram} \${initrd_name}\;run ramkernel
if test ${console} = yes;
then
setenv addcons setenv bootargs \${bootargs} console=ttyPSC\${console_nr},\${baudrate}N8
else
setenv addcons setenv bootargs \${bootargs} console=tty0
fi
setenv e1000para setenv bootargs \${bootargs} e1000.TxDescriptors=256 e1000.SmartPowerDownEnable=1
setenv set_static_ip setenv ipaddr \${static_ipaddr}
setenv set_static_nm setenv netmask \${static_netmask}
setenv set_static_gw setenv gatewayip \${static_gateway}
setenv set_ip setenv ip \${ipaddr}::\${gatewayip}:\${netmask}
setenv ramparam setenv bootargs root=/dev/ram0 ro rootfstype=squashfs
if test ${oprofile} = yes;
then
setenv addprofile setenv bootargs \${bootargs} profile=\${profile}
fi
if test ${autoscript_boot} != no;
then
if test ${netboot} = yes;
then
bootp
if test $? = 0;
then
echo "=== bootp succeeded -> netboot ==="
run set_ip
run getdtb rundtb bootfromnet ramparam addcons e1000para addprofile bootdtb
else
echo "=== netboot failed ==="
fi
fi
run set_static_ip set_static_nm set_static_gw set_ip
echo "=== bootfromflash ==="
run cpdtb rundtb bootfromflash
else
echo "=== boot stopped with autoscript_boot no ==="
fi

View file

@ -1 +0,0 @@
bootscript.img

View file

@ -1,12 +0,0 @@
if TARGET_MVSMR
config SYS_BOARD
default "mvsmr"
config SYS_VENDOR
default "matrix_vision"
config SYS_CONFIG_NAME
default "MVSMR"
endif

View file

@ -1,6 +0,0 @@
MVSMR BOARD
#M: Andre Schwarz <andre.schwarz@matrix-vision.de>
S: Orphan (since 2014-03)
F: board/matrix_vision/mvsmr/
F: include/configs/MVSMR.h
F: configs/MVSMR_defconfig

View file

@ -1,18 +0,0 @@
#
# (C) Copyright 2003
# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
#
# (C) Copyright 2004-2008
# Matrix-Vision GmbH, info@matrix-vision.de
#
# SPDX-License-Identifier: GPL-2.0+
#
obj-y := mvsmr.o fpga.o
extra-y := bootscript.img
MKIMAGEFLAGS_bootscript.image := -T script -C none -n mvSMR_Script
$(obj)/bootscript.img: $(src)/bootscript
$(call cmd,mkimage)

View file

@ -1,55 +0,0 @@
Matrix Vision mvSMR
-------------------
1. Board Description
The mvSMR is a 75x130mm single image processing board used
in automation. Power Supply is 24VDC.
2 System Components
2.1 CPU
Freescale MPC5200B CPU running at 400MHz core and 133MHz XLB/IPB.
64MB DDR-I @ 133MHz.
8 MByte Nor Flash on local bus.
2 serial ports. Console running on ttyS0 @ 115200 8N1.
2.2 PCI
PCI clock fixed at 33MHz due to old'n'slow Xilinx PCI core.
2.3 FPGA
Xilinx Spartan-3 XC3S200 with PCI DMA engine.
Connects to Matrix Vision specific CCD/CMOS sensor interface.
2.4 I2C
EEPROM @ 0xA0 for vendor specifics.
image sensor interface (slave addresses depend on sensor)
3 Flash layout.
reset vector is 0x00000100, i.e. "LOWBOOT".
FF800000 u-boot
FF806000 u-boot script image
FF808000 u-boot environment
FF840000 FPGA raw bit file
FF880000 root FS
FFF00000 kernel
4 Booting
On startup the bootscript @ FF806000 is executed. This script can be
exchanged easily. Default boot mode is "boot from flash", i.e. system
works stand-alone.
This behaviour depends on some environment variables :
"netboot" : yes ->try dhcp/bootp and boot from network.
A "dhcp_client_id" and "dhcp_vendor-class-identifier" can be used for
DHCP server configuration, e.g. to provide different images to
different devices.
During netboot the system tries to get 3 image files:
1. Kernel - name + data is given during BOOTP.
2. Initrd - name is stored in "initrd_name"
Fallback files are the flash versions.

View file

@ -1,42 +0,0 @@
echo
echo "==== running autoscript ===="
echo
setenv boot24 'bootm ${kernel_boot} ${mv_initrd_addr_ram}'
setenv ramkernel 'setenv kernel_boot ${loadaddr}'
setenv flashkernel 'setenv kernel_boot ${mv_kernel_addr}'
setenv cpird 'cp ${mv_initrd_addr} ${mv_initrd_addr_ram} ${mv_initrd_length}'
setenv bootfromflash run flashkernel cpird addcons boot24
setenv bootfromnet 'tftp ${mv_initrd_addr_ram} ${initrd_name};run ramkernel'
if test ${console} = yes;
then
setenv addcons 'setenv bootargs ${bootargs} console=ttyS${console_nr},${baudrate}N8'
else
setenv addcons 'setenv bootargs ${bootargs} console=tty0'
fi
setenv set_static_ip 'setenv ipaddr ${static_ipaddr}'
setenv set_static_nm 'setenv netmask ${static_netmask}'
setenv set_static_gw 'setenv gatewayip ${static_gateway}'
setenv set_ip 'setenv ip ${ipaddr}::${gatewayip}:${netmask}'
if test ${servicemode} != yes;
then
echo "=== forced flash mode ==="
run set_static_ip set_static_nm set_static_gw set_ip bootfromflash
fi
if test ${autoscript_boot} != no;
then
if test ${netboot} = yes;
then
bootp
if test $? = 0;
then
echo "=== bootp succeeded -> netboot ==="
run set_ip bootfromnet addcons boot24
else
echo "=== netboot failed ==="
fi
fi
echo "=== bootfromflash ==="
run set_static_ip set_static_nm set_static_gw set_ip bootfromflash
else
echo "=== boot stopped with autoscript_boot no ==="
fi

View file

@ -1,112 +0,0 @@
/*
* (C) Copyright 2002
* Rich Ireland, Enterasys Networks, rireland@enterasys.com.
* Keith Outwater, keith_outwater@mvis.com.
*
* (C) Copyright 2010
* Andre Schwarz, Matrix Vision GmbH, andre.schwarz@matrix-vision.de
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <spartan3.h>
#include <command.h>
#include <asm/io.h>
#include "fpga.h"
#include "mvsmr.h"
xilinx_spartan3_slave_serial_fns fpga_fns = {
fpga_pre_config_fn,
fpga_pgm_fn,
fpga_clk_fn,
fpga_init_fn,
fpga_done_fn,
fpga_wr_fn,
0
};
xilinx_desc spartan3 = {
xilinx_spartan2,
slave_serial,
XILINX_XC3S200_SIZE,
(void *) &fpga_fns,
0,
};
DECLARE_GLOBAL_DATA_PTR;
int mvsmr_init_fpga(void)
{
fpga_init();
fpga_add(fpga_xilinx, &spartan3);
return 1;
}
int fpga_init_fn(int cookie)
{
struct mpc5xxx_gpio *gpio = (struct mpc5xxx_gpio *)MPC5XXX_GPIO;
if (in_be32(&gpio->simple_ival) & FPGA_CONFIG)
return 0;
return 1;
}
int fpga_done_fn(int cookie)
{
struct mpc5xxx_gpio *gpio = (struct mpc5xxx_gpio *)MPC5XXX_GPIO;
int result = 0;
udelay(10);
if (in_be32(&gpio->simple_ival) & FPGA_DONE)
result = 1;
return result;
}
int fpga_pgm_fn(int assert, int flush, int cookie)
{
struct mpc5xxx_gpio *gpio = (struct mpc5xxx_gpio *)MPC5XXX_GPIO;
if (!assert)
setbits_8(&gpio->sint_dvo, FPGA_STATUS);
else
clrbits_8(&gpio->sint_dvo, FPGA_STATUS);
return assert;
}
int fpga_clk_fn(int assert_clk, int flush, int cookie)
{
struct mpc5xxx_gpio *gpio = (struct mpc5xxx_gpio *)MPC5XXX_GPIO;
if (assert_clk)
setbits_be32(&gpio->simple_dvo, FPGA_CCLK);
else
clrbits_be32(&gpio->simple_dvo, FPGA_CCLK);
return assert_clk;
}
int fpga_wr_fn(int assert_write, int flush, int cookie)
{
struct mpc5xxx_gpio *gpio = (struct mpc5xxx_gpio *)MPC5XXX_GPIO;
if (assert_write)
setbits_be32(&gpio->simple_dvo, FPGA_DIN);
else
clrbits_be32(&gpio->simple_dvo, FPGA_DIN);
return assert_write;
}
int fpga_pre_config_fn(int cookie)
{
struct mpc5xxx_gpio *gpio = (struct mpc5xxx_gpio *)MPC5XXX_GPIO;
setbits_8(&gpio->sint_dvo, FPGA_STATUS);
return 0;
}

View file

@ -1,15 +0,0 @@
/*
* (C) Copyright 2008
* Andre Schwarz, Matrix Vision GmbH, andre.schwarz@matrix-vision.de
*
* SPDX-License-Identifier: GPL-2.0+
*/
extern int mvsmr_init_fpga(void);
extern int fpga_pgm_fn(int assert_pgm, int flush, int cookie);
extern int fpga_init_fn(int cookie);
extern int fpga_clk_fn(int assert_clk, int flush, int cookie);
extern int fpga_wr_fn(int assert_write, int flush, int cookie);
extern int fpga_done_fn(int cookie);
extern int fpga_pre_config_fn(int cookie);

View file

@ -1,248 +0,0 @@
/*
* (C) Copyright 2003
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* (C) Copyright 2004
* Mark Jonas, Freescale Semiconductor, mark.jonas@motorola.com.
*
* (C) Copyright 2005-2010
* Andre Schwarz, Matrix Vision GmbH, andre.schwarz@matrix-vision.de
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <mpc5xxx.h>
#include <malloc.h>
#include <pci.h>
#include <i2c.h>
#include <fpga.h>
#include <environment.h>
#include <netdev.h>
#include <asm/io.h>
#include "fpga.h"
#include "mvsmr.h"
#include "../common/mv_common.h"
#define SDRAM_DDR 1
#define SDRAM_MODE 0x018D0000
#define SDRAM_EMODE 0x40090000
#define SDRAM_CONTROL 0x715f0f00
#define SDRAM_CONFIG1 0xd3722930
#define SDRAM_CONFIG2 0x46770000
DECLARE_GLOBAL_DATA_PTR;
static void sdram_start(int hi_addr)
{
long hi_bit = hi_addr ? 0x01000000 : 0;
/* unlock mode register */
out_be32((u32 *)MPC5XXX_SDRAM_CTRL, SDRAM_CONTROL | 0x80000000 |
hi_bit);
/* precharge all banks */
out_be32((u32 *)MPC5XXX_SDRAM_CTRL, SDRAM_CONTROL | 0x80000002 |
hi_bit);
/* set mode register: extended mode */
out_be32((u32 *)MPC5XXX_SDRAM_MODE, SDRAM_EMODE);
/* set mode register: reset DLL */
out_be32((u32 *)MPC5XXX_SDRAM_MODE, SDRAM_MODE | 0x04000000);
/* precharge all banks */
out_be32((u32 *)MPC5XXX_SDRAM_CTRL, SDRAM_CONTROL | 0x80000002 |
hi_bit);
/* auto refresh */
out_be32((u32 *)MPC5XXX_SDRAM_CTRL, SDRAM_CONTROL | 0x80000004 |
hi_bit);
/* set mode register */
out_be32((u32 *)MPC5XXX_SDRAM_MODE, SDRAM_MODE);
/* normal operation */
out_be32((u32 *)MPC5XXX_SDRAM_CTRL, SDRAM_CONTROL | hi_bit);
}
phys_addr_t initdram(int board_type)
{
ulong dramsize = 0;
ulong test1,
test2;
/* setup SDRAM chip selects */
out_be32((u32 *)MPC5XXX_SDRAM_CS0CFG, 0x0000001e);
/* setup config registers */
out_be32((u32 *)MPC5XXX_SDRAM_CONFIG1, SDRAM_CONFIG1);
out_be32((u32 *)MPC5XXX_SDRAM_CONFIG2, SDRAM_CONFIG2);
/* find RAM size using SDRAM CS0 only */
sdram_start(0);
test1 = get_ram_size((long *)CONFIG_SYS_SDRAM_BASE, 0x80000000);
sdram_start(1);
test2 = get_ram_size((long *)CONFIG_SYS_SDRAM_BASE, 0x80000000);
if (test1 > test2) {
sdram_start(0);
dramsize = test1;
} else
dramsize = test2;
if (dramsize < (1 << 20))
dramsize = 0;
if (dramsize > 0)
out_be32((u32 *)MPC5XXX_SDRAM_CS0CFG, 0x13 +
__builtin_ffs(dramsize >> 20) - 1);
else
out_be32((u32 *)MPC5XXX_SDRAM_CS0CFG, 0);
return dramsize;
}
void mvsmr_init_gpio(void)
{
struct mpc5xxx_gpio *gpio = (struct mpc5xxx_gpio *)MPC5XXX_GPIO;
struct mpc5xxx_wu_gpio *wu_gpio =
(struct mpc5xxx_wu_gpio *)MPC5XXX_WU_GPIO;
struct mpc5xxx_gpt_0_7 *timers = (struct mpc5xxx_gpt_0_7 *)MPC5XXX_GPT;
printf("Ports : 0x%08x\n", gpio->port_config);
printf("PORCFG: 0x%08x\n", in_be32((unsigned *)MPC5XXX_CDM_PORCFG));
out_be32(&gpio->simple_ddr, SIMPLE_DDR);
out_be32(&gpio->simple_dvo, SIMPLE_DVO);
out_be32(&gpio->simple_ode, SIMPLE_ODE);
out_be32(&gpio->simple_gpioe, SIMPLE_GPIOEN);
out_8(&gpio->sint_ode, SINT_ODE);
out_8(&gpio->sint_ddr, SINT_DDR);
out_8(&gpio->sint_dvo, SINT_DVO);
out_8(&gpio->sint_inten, SINT_INTEN);
out_be16(&gpio->sint_itype, SINT_ITYPE);
out_8(&gpio->sint_gpioe, SINT_GPIOEN);
out_8(&wu_gpio->ode, WKUP_ODE);
out_8(&wu_gpio->ddr, WKUP_DIR);
out_8(&wu_gpio->dvo, WKUP_DO);
out_8(&wu_gpio->enable, WKUP_EN);
out_be32(&timers->gpt0.emsr, 0x00000234); /* OD output high */
out_be32(&timers->gpt1.emsr, 0x00000234);
out_be32(&timers->gpt2.emsr, 0x00000234);
out_be32(&timers->gpt3.emsr, 0x00000234);
out_be32(&timers->gpt4.emsr, 0x00000234);
out_be32(&timers->gpt5.emsr, 0x00000234);
out_be32(&timers->gpt6.emsr, 0x00000024); /* push-pull output low */
out_be32(&timers->gpt7.emsr, 0x00000024);
}
int misc_init_r(void)
{
char *s = getenv("reset_env");
if (s) {
printf(" === FACTORY RESET ===\n");
mv_reset_environment();
saveenv();
}
return -1;
}
void mvsmr_get_dbg_present(void)
{
struct mpc5xxx_gpio *gpio = (struct mpc5xxx_gpio *)MPC5XXX_GPIO;
struct mpc5xxx_psc *psc = (struct mpc5xxx_psc *)MPC5XXX_PSC1;
if (in_be32(&gpio->simple_ival) & COP_PRESENT) {
setenv("dbg_present", "no\0");
setenv("bootstopkey", "abcdefghijklmnopqrstuvwxyz\0");
} else {
setenv("dbg_present", "yes\0");
setenv("bootstopkey", "s\0");
setbits_8(&psc->command, PSC_RX_ENABLE);
}
}
void mvsmr_get_service_mode(void)
{
struct mpc5xxx_wu_gpio *wu_gpio =
(struct mpc5xxx_wu_gpio *)MPC5XXX_WU_GPIO;
if (in_8(&wu_gpio->ival) & SERVICE_MODE)
setenv("servicemode", "no\0");
else
setenv("servicemode", "yes\0");
}
int mvsmr_get_mac(void)
{
unsigned char mac[6];
struct mpc5xxx_wu_gpio *wu_gpio =
(struct mpc5xxx_wu_gpio *)MPC5XXX_WU_GPIO;
if (in_8(&wu_gpio->ival) & LAN_PRSNT) {
setenv("lan_present", "no\0");
return -1;
} else
setenv("lan_present", "yes\0");
i2c_read(0x50, 0, 1, mac, 6);
eth_setenv_enetaddr("ethaddr", mac);
return 0;
}
int checkboard(void)
{
mvsmr_init_gpio();
printf("Board: Matrix Vision mvSMR\n");
return 0;
}
void flash_preinit(void)
{
/*
* Now, when we are in RAM, enable flash write
* access for detection process.
* Note that CS_BOOT cannot be cleared when
* executing in flash.
*/
clrbits_be32((u32 *)MPC5XXX_BOOTCS_CFG, 0x1);
}
void flash_afterinit(ulong size)
{
out_be32((u32 *)MPC5XXX_BOOTCS_START,
START_REG(CONFIG_SYS_BOOTCS_START | size));
out_be32((u32 *)MPC5XXX_CS0_START,
START_REG(CONFIG_SYS_BOOTCS_START | size));
out_be32((u32 *)MPC5XXX_BOOTCS_STOP,
STOP_REG(CONFIG_SYS_BOOTCS_START | size, size));
out_be32((u32 *)MPC5XXX_CS0_STOP,
STOP_REG(CONFIG_SYS_BOOTCS_START | size, size));
}
struct pci_controller hose;
void pci_init_board(void)
{
mvsmr_get_dbg_present();
mvsmr_get_service_mode();
mvsmr_init_fpga();
mv_load_fpga();
pci_mpc5xxx_init(&hose);
}
int board_eth_init(bd_t *bis)
{
if (!mvsmr_get_mac())
return cpu_eth_init(bis);
return pci_eth_init(bis);
}

View file

@ -1,43 +0,0 @@
#include <pci.h>
extern void pci_mpc5xxx_init(struct pci_controller *);
#define FPGA_DIN MPC5XXX_GPIO_SIMPLE_PSC3_0
#define FPGA_CCLK MPC5XXX_GPIO_SIMPLE_PSC3_1
#define FPGA_DONE MPC5XXX_GPIO_SIMPLE_PSC3_2
#define FPGA_CONFIG MPC5XXX_GPIO_SIMPLE_PSC3_3
#define FPGA_STATUS MPC5XXX_GPIO_SINT_PSC3_4
#define S_FPGA_DIN MPC5XXX_GPIO_SINT_PSC3_5
#define S_FPGA_CCLK MPC5XXX_GPIO_SIMPLE_PSC3_6
#define S_FPGA_DONE MPC5XXX_GPIO_SIMPLE_PSC3_7
#define S_FPGA_CONFIG MPC5XXX_GPIO_SINT_PSC3_8
#define S_FPGA_STATUS MPC5XXX_GPIO_WKUP_PSC3_9
#define MAN_RST MPC5XXX_GPIO_WKUP_PSC6_0
#define WD_TS MPC5XXX_GPIO_WKUP_PSC6_1
#define WD_WDI MPC5XXX_GPIO_SIMPLE_PSC6_2
#define COP_PRESENT MPC5XXX_GPIO_SIMPLE_PSC6_3
#define SERVICE_MODE MPC5XXX_GPIO_WKUP_6
#define FLASH_RBY MPC5XXX_GPIO_WKUP_7
#define UART_EN1 MPC5XXX_GPIO_WKUP_PSC1_4
#define LAN_PRSNT MPC5XXX_GPIO_WKUP_PSC2_4
#define SIMPLE_DDR (FPGA_DIN | FPGA_CCLK | FPGA_CONFIG | WD_WDI |\
S_FPGA_CCLK)
#define SIMPLE_DVO (FPGA_CONFIG)
#define SIMPLE_ODE (FPGA_CONFIG)
#define SIMPLE_GPIOEN (FPGA_DIN | FPGA_CCLK | FPGA_DONE | FPGA_CONFIG |\
S_FPGA_CCLK | S_FPGA_DONE | WD_WDI | COP_PRESENT)
#define SINT_ODE 0x1
#define SINT_DDR 0x3
#define SINT_DVO 0x1
#define SINT_INTEN 0
#define SINT_ITYPE 0
#define SINT_GPIOEN (FPGA_STATUS | S_FPGA_DIN | S_FPGA_CONFIG)
#define WKUP_ODE (MAN_RST | S_FPGA_STATUS)
#define WKUP_DIR (MAN_RST | WD_TS | S_FPGA_STATUS)
#define WKUP_DO (MAN_RST | WD_TS | S_FPGA_STATUS)
#define WKUP_EN (MAN_RST | WD_TS | S_FPGA_STATUS | SERVICE_MODE |\
FLASH_RBY | UART_EN1 | LAN_PRSNT)

View file

@ -1,89 +0,0 @@
/*
* (C) Copyright 2003-2004
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
* (C) Copyright 2010
* André Schwarz, Matrix Vision GmbH, as@matrix-vision.de
*
* SPDX-License-Identifier: GPL-2.0+
*/
OUTPUT_ARCH(powerpc)
SECTIONS
{
/* Read-only sections, merged into text segment: */
.text :
{
/* WARNING - the following is hand-optimized to fit within */
/* the first two sectors (=8KB) of our S29GL flash chip */
arch/powerpc/cpu/mpc5xxx/start.o (.text*)
arch/powerpc/cpu/mpc5xxx/traps.o (.text*)
board/matrix_vision/common/built-in.o (.text*)
/* This is only needed to force failure if size of above code will ever */
/* increase and grow into reserved space. */
. = ALIGN(0x2000); /* location counter has to be 0x4000 now */
. += 0x4000; /* ->0x8000, i.e. move to env_offset */
. = env_offset; /* ld error as soon as above ALIGN misplaces lc */
common/env_embedded.o (.ppcenv)
*(.text*)
. = ALIGN(16);
*(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*)))
}
/* Read-write section, merged into data segment: */
. = (. + 0x0FFF) & 0xFFFFF000;
_erotext = .;
PROVIDE (erotext = .);
.reloc :
{
_GOT2_TABLE_ = .;
KEEP(*(.got2))
KEEP(*(.got))
PROVIDE(_GLOBAL_OFFSET_TABLE_ = . + 4);
_FIXUP_TABLE_ = .;
KEEP(*(.fixup))
}
__got2_entries = ((_GLOBAL_OFFSET_TABLE_ - _GOT2_TABLE_) >> 2) - 1;
__fixup_entries = (. - _FIXUP_TABLE_) >> 2;
.data :
{
*(.data*)
*(.sdata*)
}
_edata = .;
PROVIDE (edata = .);
. = .;
. = ALIGN(4);
.u_boot_list : {
KEEP(*(SORT(.u_boot_list*)));
}
. = .;
__start___ex_table = .;
__ex_table : { *(__ex_table) }
__stop___ex_table = .;
. = ALIGN(4096);
__init_begin = .;
.text.init : { *(.text.init) }
.data.init : { *(.data.init) }
. = ALIGN(4096);
__init_end = .;
__bss_start = .;
.bss (NOLOAD) :
{
*(.bss*)
*(.sbss*)
. = ALIGN(4);
}
__bss_end = . ;
PROVIDE (end = .);
}

View file

@ -1,4 +0,0 @@
CONFIG_SYS_EXTRA_OPTIONS="MVBC_P"
CONFIG_PPC=y
CONFIG_MPC5xxx=y
CONFIG_TARGET_MVBC_P=y

View file

@ -1,3 +0,0 @@
CONFIG_PPC=y
CONFIG_MPC5xxx=y
CONFIG_TARGET_MVSMR=y

View file

@ -12,6 +12,8 @@ The list should be sorted in reverse chronological order.
Board Arch CPU Commit Removed Last known maintainer/contact
=================================================================================================
MVBC_P powerpc mpc5xxx - - Andre Schwarz <andre.schwarz@matrix-vision.de>
MVSMR powerpc mpc5xxx - - Andre Schwarz <andre.schwarz@matrix-vision.de>
MERGERBOX powerpc mpc83xx - - Andre Schwarz <andre.schwarz@matrix-vision.de>
MVBLM7 powerpc mpc83xx - - Andre Schwarz <andre.schwarz@matrix-vision.de>
bluestone powerpc ppc4xx - - Tirumala Marri <tmarri@apm.com>

View file

@ -1,300 +0,0 @@
/*
* (C) Copyright 2003-2004
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* (C) Copyright 2004-2008
* Matrix-Vision GmbH, andre.schwarz@matrix-vision.de
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
#define __CONFIG_H
#include <version.h>
#define CONFIG_MPC5200 1
#ifndef CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_TEXT_BASE 0xFF800000
#endif
#define CONFIG_SYS_MPC5XXX_CLKIN 33000000
#define CONFIG_MISC_INIT_R 1
#define CONFIG_SYS_CACHELINE_SIZE 32
#ifdef CONFIG_CMD_KGDB
#define CONFIG_SYS_CACHELINE_SHIFT 5
#endif
#define CONFIG_PSC_CONSOLE 1
#define CONFIG_BAUDRATE 115200
#define CONFIG_SYS_BAUDRATE_TABLE {9600, 19200, 38400, 57600, 115200, 230400}
#define CONFIG_PCI 1
#define CONFIG_PCI_PNP 1
#undef CONFIG_PCI_SCAN_SHOW
#define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1
#define CONFIG_PCI_MEM_BUS 0x40000000
#define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS
#define CONFIG_PCI_MEM_SIZE 0x10000000
#define CONFIG_PCI_IO_BUS 0x50000000
#define CONFIG_PCI_IO_PHYS CONFIG_PCI_IO_BUS
#define CONFIG_PCI_IO_SIZE 0x01000000
#define CONFIG_SYS_XLB_PIPELINING 1
#define CONFIG_HIGH_BATS 1
#define MV_CI mvBlueCOUGAR-P
#define MV_VCI mvBlueCOUGAR-P
#define MV_FPGA_DATA 0xff860000
#define MV_FPGA_SIZE 0
#define MV_KERNEL_ADDR 0xffd00000
#define MV_INITRD_ADDR 0xff900000
#define MV_INITRD_LENGTH 0x00400000
#define MV_SCRATCH_ADDR 0x00000000
#define MV_SCRATCH_LENGTH MV_INITRD_LENGTH
#define MV_SCRIPT_ADDR 0xff840000
#define MV_SCRIPT_ADDR2 0xff850000
#define MV_DTB_ADDR 0xfffc0000
#define CONFIG_SHOW_BOOT_PROGRESS 1
#define MV_KERNEL_ADDR_RAM 0x00100000
#define MV_DTB_ADDR_RAM 0x00600000
#define MV_INITRD_ADDR_RAM 0x01000000
/* pass open firmware flat tree */
#define CONFIG_OF_LIBFDT 1
#define CONFIG_OF_BOARD_SETUP 1
#define OF_CPU "PowerPC,5200@0"
#define OF_SOC "soc5200@f0000000"
#define OF_TBCLK (bd->bi_busfreq / 4)
#define MV_DTB_NAME mvbc-p.dtb
#define CONFIG_OF_STDOUT_VIA_ALIAS 1
/*
* Supported commands
*/
#include <config_cmd_default.h>
#define CONFIG_CMD_CACHE
#define CONFIG_CMD_NET
#define CONFIG_CMD_PING
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_SDRAM
#define CONFIG_CMD_PCI
#define CONFIG_CMD_FPGA
#define CONFIG_CMD_FPGA_LOADMK
#define CONFIG_CMD_I2C
#undef CONFIG_WATCHDOG
#define CONFIG_BOOTP_VENDOREX
#define CONFIG_BOOTP_SUBNETMASK
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_DNS
#define CONFIG_BOOTP_DNS2
#define CONFIG_BOOTP_HOSTNAME
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_NTPSERVER
#define CONFIG_BOOTP_RANDOM_DELAY
#define CONFIG_BOOTP_SEND_HOSTNAME
#define CONFIG_LIB_RAND
/*
* Autoboot
*/
#define CONFIG_BOOTDELAY 2
#define CONFIG_AUTOBOOT_KEYED
#define CONFIG_AUTOBOOT_STOP_STR "s"
#define CONFIG_ZERO_BOOTDELAY_CHECK
#define CONFIG_RESET_TO_RETRY 1000
#define CONFIG_BOOTCOMMAND "if imi ${script_addr}; \
then source ${script_addr}; \
else source ${script_addr2}; \
fi;"
#define CONFIG_BOOTARGS "root=/dev/ram ro rootfstype=squashfs"
#define CONFIG_ENV_OVERWRITE
#define CONFIG_EXTRA_ENV_SETTINGS \
"console_nr=0\0" \
"console=yes\0" \
"stdin=serial\0" \
"stdout=serial\0" \
"stderr=serial\0" \
"fpga=0\0" \
"fpgadata=" __stringify(MV_FPGA_DATA) "\0" \
"fpgadatasize=" __stringify(MV_FPGA_SIZE) "\0" \
"script_addr=" __stringify(MV_SCRIPT_ADDR) "\0" \
"script_addr2=" __stringify(MV_SCRIPT_ADDR2) "\0" \
"mv_kernel_addr=" __stringify(MV_KERNEL_ADDR) "\0" \
"mv_kernel_addr_ram=" __stringify(MV_KERNEL_ADDR_RAM) "\0" \
"mv_initrd_addr=" __stringify(MV_INITRD_ADDR) "\0" \
"mv_initrd_addr_ram=" __stringify(MV_INITRD_ADDR_RAM) "\0" \
"mv_initrd_length=" __stringify(MV_INITRD_LENGTH) "\0" \
"mv_dtb_addr=" __stringify(MV_DTB_ADDR) "\0" \
"mv_dtb_addr_ram=" __stringify(MV_DTB_ADDR_RAM) "\0" \
"dtb_name=" __stringify(MV_DTB_NAME) "\0" \
"mv_scratch_addr=" __stringify(MV_SCRATCH_ADDR) "\0" \
"mv_scratch_length=" __stringify(MV_SCRATCH_LENGTH) "\0" \
"mv_version=" U_BOOT_VERSION "\0" \
"dhcp_client_id=" __stringify(MV_CI) "\0" \
"dhcp_vendor-class-identifier=" __stringify(MV_VCI) "\0" \
"netretry=no\0" \
"use_static_ipaddr=no\0" \
"static_ipaddr=192.168.90.10\0" \
"static_netmask=255.255.255.0\0" \
"static_gateway=0.0.0.0\0" \
"initrd_name=uInitrd.mvbc-p-rfs\0" \
"zcip=no\0" \
"netboot=yes\0" \
"mvtest=Ff\0" \
"tried_bootfromflash=no\0" \
"tried_bootfromnet=no\0" \
"use_dhcp=yes\0" \
"gev_start=yes\0" \
"mvbcdma_debug=0\0" \
"mvbcia_debug=0\0" \
"propdev_debug=0\0" \
"gevss_debug=0\0" \
"watchdog=1\0" \
"sensor_cnt=1\0" \
""
/*
* IPB Bus clocking configuration.
*/
#define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK
#define CONFIG_SYS_PCICLK_EQUALS_IPBCLK_DIV2
/*
* Flash configuration
*/
#undef CONFIG_FLASH_16BIT
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_CFI_AMD_RESET 1
#define CONFIG_SYS_FLASH_EMPTY_INFO
#define CONFIG_SYS_FLASH_ERASE_TOUT 50000
#define CONFIG_SYS_FLASH_WRITE_TOUT 1000
#define CONFIG_SYS_MAX_FLASH_BANKS 1
#define CONFIG_SYS_MAX_FLASH_SECT 256
#define CONFIG_SYS_LOWBOOT
#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_FLASH_SIZE 0x00800000
/*
* Environment settings
*/
#define CONFIG_ENV_IS_IN_FLASH
#undef CONFIG_SYS_FLASH_PROTECTION
#define CONFIG_ENV_ADDR 0xFFFE0000
#define CONFIG_ENV_SIZE 0x10000
#define CONFIG_ENV_SECT_SIZE 0x10000
#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR+CONFIG_ENV_SIZE)
#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
/*
* Memory map
*/
#define CONFIG_SYS_MBAR 0xF0000000
#define CONFIG_SYS_SDRAM_BASE 0x00000000
#define CONFIG_SYS_DEFAULT_MBAR 0x80000000
#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM
#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
#define CONFIG_SYS_RAMBOOT 1
#endif
/* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */
#define CONFIG_SYS_MONITOR_LEN (512 << 10)
#define CONFIG_SYS_MALLOC_LEN (512 << 10)
#define CONFIG_SYS_BOOTMAPSZ (8 << 20)
/*
* I2C configuration
*/
#define CONFIG_HARD_I2C 1
#define CONFIG_SYS_I2C_MODULE 1
#define CONFIG_SYS_I2C_SPEED 86000
#define CONFIG_SYS_I2C_SLAVE 0x7F
/*
* Ethernet configuration
*/
#define CONFIG_NET_RETRY_COUNT 5
#define CONFIG_E1000
#define CONFIG_E1000_FALLBACK_MAC { 0xb6, 0xb4, 0x45, 0xeb, 0xfb, 0xc0 }
#undef CONFIG_MPC5xxx_FEC
#undef CONFIG_PHY_ADDR
#define CONFIG_NETDEV eth0
/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_HUSH_PARSER
#define CONFIG_CMDLINE_EDITING
#undef CONFIG_SYS_LONGHELP
#ifdef CONFIG_CMD_KGDB
#define CONFIG_SYS_CBSIZE 1024
#else
#define CONFIG_SYS_CBSIZE 256
#endif
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
#define CONFIG_SYS_MAXARGS 16
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
#define CONFIG_SYS_MEMTEST_START 0x00800000
#define CONFIG_SYS_MEMTEST_END 0x02f00000
/* default load address */
#define CONFIG_SYS_LOAD_ADDR 0x02000000
/* default location for tftp and bootm */
#define CONFIG_LOADADDR 0x00200000
/*
* Various low-level settings
*/
#define CONFIG_SYS_GPS_PORT_CONFIG 0x20000004
#define CONFIG_SYS_HID0_INIT (HID0_ICE | HID0_ICFI)
#define CONFIG_SYS_HID0_FINAL HID0_ICE
#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE
#define CONFIG_SYS_BOOTCS_CFG 0x00047800
#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE
#define CONFIG_SYS_CS_BURST 0x000000f0
#define CONFIG_SYS_CS_DEADCYCLE 0x33333303
#define CONFIG_SYS_RESET_ADDRESS 0x00000100
#undef FPGA_DEBUG
#undef CONFIG_SYS_FPGA_PROG_FEEDBACK
#define CONFIG_FPGA
#define CONFIG_FPGA_ALTERA 1
#define CONFIG_FPGA_CYCLON2 1
#define CONFIG_FPGA_COUNT 1
#endif

View file

@ -1,270 +0,0 @@
/*
* (C) Copyright 2003-2004
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* (C) Copyright 2004-2010
* Matrix-Vision GmbH, andre.schwarz@matrix-vision.de
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
#define __CONFIG_H
#include <version.h>
#define CONFIG_MPC5200 1
#ifndef CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_TEXT_BASE 0xFF800000
#endif
#define CONFIG_SYS_LDSCRIPT "board/matrix_vision/mvsmr/u-boot.lds"
#define CONFIG_SYS_MPC5XXX_CLKIN 33000000
#define CONFIG_MISC_INIT_R 1
#define CONFIG_SYS_CACHELINE_SIZE 32
#ifdef CONFIG_CMD_KGDB
#define CONFIG_SYS_CACHELINE_SHIFT 5
#endif
#define CONFIG_PSC_CONSOLE 1
#define CONFIG_BAUDRATE 115200
#define CONFIG_SYS_BAUDRATE_TABLE {9600, 19200, 38400, 57600, 115200,\
230400}
#define CONFIG_PCI 1
#define CONFIG_PCI_PNP 1
#undef CONFIG_PCI_SCAN_SHOW
#define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1
#define CONFIG_PCI_MEM_BUS 0x40000000
#define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS
#define CONFIG_PCI_MEM_SIZE 0x10000000
#define CONFIG_PCI_IO_BUS 0x50000000
#define CONFIG_PCI_IO_PHYS CONFIG_PCI_IO_BUS
#define CONFIG_PCI_IO_SIZE 0x01000000
#define CONFIG_SYS_XLB_PIPELINING 1
#define CONFIG_HIGH_BATS 1
#define MV_CI mvSMR
#define MV_VCI mvSMR
#define MV_FPGA_DATA 0xff840000
#define MV_FPGA_SIZE 0x1ff88
#define MV_KERNEL_ADDR 0xfff00000
#define MV_SCRIPT_ADDR 0xff806000
#define MV_INITRD_ADDR 0xff880000
#define MV_INITRD_LENGTH 0x00240000
#define MV_SCRATCH_ADDR 0xffcc0000
#define MV_SCRATCH_LENGTH MV_INITRD_LENGTH
#define CONFIG_SHOW_BOOT_PROGRESS 1
#define MV_KERNEL_ADDR_RAM 0x00100000
#define MV_INITRD_ADDR_RAM 0x00400000
/*
* Supported commands
*/
#include <config_cmd_default.h>
#define CONFIG_CMD_CACHE
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_FPGA
#define CONFIG_CMD_FPGA_LOADMK
#define CONFIG_CMD_I2C
#define CONFIG_CMD_MII
#define CONFIG_CMD_NET
#define CONFIG_CMD_PCI
#define CONFIG_CMD_PING
#define CONFIG_CMD_SDRAM
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_DNS
#define CONFIG_BOOTP_DNS2
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
#define CONFIG_BOOTP_NTPSERVER
#define CONFIG_BOOTP_RANDOM_DELAY
#define CONFIG_BOOTP_SEND_HOSTNAME
#define CONFIG_BOOTP_SUBNETMASK
#define CONFIG_BOOTP_VENDOREX
#define CONFIG_LIB_RAND
/*
* Autoboot
*/
#define CONFIG_BOOTDELAY 1
#define CONFIG_AUTOBOOT_KEYED
#define CONFIG_AUTOBOOT_STOP_STR "abcdefg"
#define CONFIG_ZERO_BOOTDELAY_CHECK
#define CONFIG_BOOTCOMMAND "source ${script_addr}"
#define CONFIG_BOOTARGS "root=/dev/ram ro rootfstype=squashfs" \
" allocate=6M"
#define CONFIG_EXTRA_ENV_SETTINGS \
"console_nr=0\0" \
"console=no\0" \
"stdin=serial\0" \
"stdout=serial\0" \
"stderr=serial\0" \
"fpga=0\0" \
"fpgadata=" __stringify(MV_FPGA_DATA) "\0" \
"fpgadatasize=" __stringify(MV_FPGA_SIZE) "\0" \
"mv_kernel_addr=" __stringify(MV_KERNEL_ADDR) "\0" \
"mv_kernel_addr_ram=" __stringify(MV_KERNEL_ADDR_RAM) "\0" \
"script_addr=" __stringify(MV_SCRIPT_ADDR) "\0" \
"mv_initrd_addr=" __stringify(MV_INITRD_ADDR) "\0" \
"mv_initrd_addr_ram=" __stringify(MV_INITRD_ADDR_RAM) "\0" \
"mv_initrd_length=" __stringify(MV_INITRD_LENGTH) "\0" \
"mv_scratch_addr=" __stringify(MV_SCRATCH_ADDR) "\0" \
"mv_scratch_length=" __stringify(MV_SCRATCH_LENGTH) "\0" \
"mv_version=" U_BOOT_VERSION "\0" \
"dhcp_client_id=" __stringify(MV_CI) "\0" \
"dhcp_vendor-class-identifier=" __stringify(MV_VCI) "\0" \
"netretry=no\0" \
"use_static_ipaddr=no\0" \
"static_ipaddr=192.168.0.101\0" \
"static_netmask=255.255.255.0\0" \
"static_gateway=0.0.0.0\0" \
"initrd_name=uInitrd.mvsmr-rfs\0" \
"zcip=yes\0" \
"netboot=no\0" \
""
/*
* IPB Bus clocking configuration.
*/
#define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK
/*
* Flash configuration
*/
#undef CONFIG_FLASH_16BIT
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_CFI_AMD_RESET 1
#define CONFIG_SYS_FLASH_EMPTY_INFO
#define CONFIG_SYS_FLASH_ERASE_TOUT 50000
#define CONFIG_SYS_FLASH_WRITE_TOUT 1000
#define CONFIG_SYS_MAX_FLASH_BANKS 1
#define CONFIG_SYS_MAX_FLASH_SECT 256
#define CONFIG_SYS_LOWBOOT
#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_FLASH_SIZE 0x00800000
/*
* Environment settings
*/
#define CONFIG_ENV_IS_IN_FLASH
#undef CONFIG_SYS_FLASH_PROTECTION
#define CONFIG_OVERWRITE_ETHADDR_ONCE
#define CONFIG_ENV_OFFSET 0x8000
#define CONFIG_ENV_SIZE 0x2000
#define CONFIG_ENV_SECT_SIZE 0x2000
/* used by linker script to wrap code around */
#define CONFIG_SCRIPT_OFFSET 0x6000
#define CONFIG_SCRIPT_SECT_SIZE 0x2000
/*
* Memory map
*/
#define CONFIG_SYS_MBAR 0xF0000000
#define CONFIG_SYS_SDRAM_BASE 0x00000000
#define CONFIG_SYS_DEFAULT_MBAR 0x80000000
#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM
#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
#define CONFIG_SYS_RAMBOOT 1
#endif
/* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */
#define CONFIG_SYS_MONITOR_LEN (512 << 10)
#define CONFIG_SYS_MALLOC_LEN (512 << 10)
#define CONFIG_SYS_BOOTMAPSZ (8 << 20)
/*
* I2C configuration
*/
#define CONFIG_HARD_I2C 1
#define CONFIG_SYS_I2C_MODULE 1
#define CONFIG_SYS_I2C_SPEED 86000
#define CONFIG_SYS_I2C_SLAVE 0x7F
/*
* Ethernet configuration
*/
#define CONFIG_NET_RETRY_COUNT 5
#define CONFIG_MPC5xxx_FEC
#define CONFIG_MPC5xxx_FEC_MII100
#define CONFIG_PHY_ADDR 0x00
#define CONFIG_NETDEV eth0
/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_HUSH_PARSER
#define CONFIG_CMDLINE_EDITING
#undef CONFIG_SYS_LONGHELP
#ifdef CONFIG_CMD_KGDB
#define CONFIG_SYS_CBSIZE 1024
#else
#define CONFIG_SYS_CBSIZE 256
#endif
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
#define CONFIG_SYS_MAXARGS 16
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
#define CONFIG_SYS_MEMTEST_START 0x00800000
#define CONFIG_SYS_MEMTEST_END 0x02f00000
/* default load address */
#define CONFIG_SYS_LOAD_ADDR 0x02000000
/* default location for tftp and bootm */
#define CONFIG_LOADADDR 0x00200000
/*
* Various low-level settings
*/
#define CONFIG_SYS_GPS_PORT_CONFIG 0x00050044
#define CONFIG_SYS_HID0_INIT (HID0_ICE | HID0_ICFI)
#define CONFIG_SYS_HID0_FINAL HID0_ICE
#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE
#define CONFIG_SYS_BOOTCS_CFG 0x00047800
#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE
#define CONFIG_SYS_CS_BURST 0x000000f0
#define CONFIG_SYS_CS_DEADCYCLE 0x33333303
#define CONFIG_SYS_RESET_ADDRESS 0x00000100
#undef FPGA_DEBUG
#undef CONFIG_SYS_FPGA_PROG_FEEDBACK
#define CONFIG_FPGA
#define CONFIG_FPGA_XILINX 1
#define CONFIG_FPGA_SPARTAN2 1
#define CONFIG_FPGA_COUNT 1
#endif