Only the wandboard revD1 boards have PMIC, so when running on a wandboard
of different revision the following error is always shown on every boot:
pmic_get() ret -19
Instead of printing this error message, move it to debug level instead.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
This patch adds new jtag distro boot command to look for bootscript
file in DDR and execute it first incase of jtag bootmode.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
DEVICE_TREE variable has been added by commit 6ab6b2afa0
("dts: re-write dts/Makefile more simply with Kbuild")
where DT can be specified on command line. If it is not then
CONFIG_DEFAULT_DEVICE_TREE is used to ensure backward compatibility.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Names have to match device tree file names. Also add missing one.
Fixes: 50d9283347 ("arm64: zynqmp: Sync names for SC with Versal")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is no reason to do serial initializationin low level code. Uart
driver does it already based on DT.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is no reason to do serial initialization. Uart driver does it already
based on DT. Good effect is that it is clear which interface is console.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
MIO34 is connected to POWER_KILL signal. When MIO configuration is done in
psu_init() and this pin is assigned to PMU but PMU configuration is not
loaded yet. PMU gpio output is high that means board is powered off
immediately.
The patch is fixing this sequence that MIO34 stays assing to ps gpio IP.
PMU config is loaded in SPL and then pin assigned to PMU through
psu_post_config_data().
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
OF_BOARD and OF_SEPARATE can use board specific board_fdt_blob_setup().
OF_BOARD option is mostly used for picking up DTB from certain location.
OF_SEPARATE option is used when DTB is appended after u-boot binary.
This board specific function is aligned with current version in
lib/fdtdec.c with checking CONFIG_XILINX_OF_BOARD_DTB_ADDR address first.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The reason for this change is just get in sync with board_fdt_blob_setup()
available at lib/fdtdec.c.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Currently "script_offset_f" env variable is hardcoded, this variable
specifies from which offset of the flash boot.scr should be read/write.
As flashes are of different sizes having a fixed offset makes it
difficult to load other images into the flash which may overwrite the
boot script or cannot utilize the full memory. This current fix
creates a new config "CONFIG_BOOT_SCRIPT_OFFSET" which holds the
offset address, overwrites the "script_offset_f" variable.
Also removed existing variable with default values, as the default
values are held by CONFIG_BOOT_SCRIPT_OFFSET
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Emmc boot devcie is mounted to mmc@ff160000 controller on zynqmp.
Detect mmc alias at run time for setting up proper boot_targets
sequence instead of setting boot_targets manually.
Removed setting "modeboot" variable as it not longer need as we
switched to distro boot.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Emmc boot devcie is mounted to sdhci@f1050000 controller on versal, while
in emmc boot mode, boot tragets are set to mmc0. So removed mmc0 and using
the dev seq number from the sdhci@f1050000 controller.
Dev seq number is setup based on DT aliases that's why needs to be setup at
run time.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This target is out of maintenance and can be removed.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
CC: Stefan Roese <sr@denx.de>
CC: Valentin Longchamp <valentin.longchamp@ch.abb.com>
Reviewed-by: Stefan Roese <sr@denx.de>
For upcoming SECU board we have different MAC address offsets depending
on which functional unit we are running. In this case we need to pass
this value to the ivm_populate_env function instead of using the hard
coded config option there.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
CC: Stefan Roese <sr@denx.de>
CC: Valentin Longchamp <valentin.longchamp@ch.abb.com>
CC: Marek Vasut <marex@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
This patch only fixes a typo.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
CC: Stefan Roese <sr@denx.de>
CC: Valentin Longchamp <valentin.longchamp@ch.abb.com>
Reviewed-by: Stefan Roese <sr@denx.de>
All platforms currently use the "MCFTMR" DMA timer rather than the PIT
timer, so drop the MCFPIT code.
Cc: Huan Wang <alison.wang@nxp.com>
Cc: Angelo Dureghello <angelo@sysam.it>
Cc: TsiChung Liew <Tsi-Chung.Liew@nxp.com>
Cc: Wolfgang Wegner <w.wegner@astro-kom.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Angelo Dureghello <angelo@sysam.it>
This pull request provides:
* support for FIT images for UEFI binaries
* drivers for hardware random number generators
* an implementation of the EFI_RNG_PROTOCOL
* a sub-command for efidebug to display configuration tables
-----BEGIN PGP SIGNATURE-----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=SjPV
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-04-rc1' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-04-rc1
This pull request provides:
* support for FIT images for UEFI binaries
* drivers for hardware random number generators
* an implementation of the EFI_RNG_PROTOCOL
* a sub-command for efidebug to display configuration tables
- Various fixups for amlogic boards
- Unnecessary header includes drop into video/meson
-----BEGIN PGP SIGNATURE-----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=rkHZ
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20200108' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic
- Khadas VIM3L based on Amlogic S905D3 support
- Various fixups for amlogic boards
- Unnecessary header includes drop into video/meson
Add board_mmc_get_env_dev, otherwise,
Loading Environment from MMC...
MMC Device 0 not found
*** Warning - No MMC card found, using default environment
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
After the conversion to DM_PMIC the following output is seen:
PMIC: PMIC: PFUZE100 ID=0x10
Remove the unnecessary PMIC string from the board file to
avoid the repetead string.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Commit ec837c82d7 ("imx6: wandboard: convert to DM_PMIC")
caused the following pmic_get() error:
CPU: Freescale i.MX6QP rev1.0 at 792 MHz
Reset cause: POR
DRAM: 2 GiB
PMIC: pmic_get() ret -19
...
and since the PMIC presence is used to determine the board D1 revision,
the following error is seen when booting a board rev D1:
WARNING: Could not determine dtb to use
and the kernel does not boot at all.
Fix the regression by passing "pfuze100@8" as the correct parameter
to the pmic_get() function in the DM case.
Fixes: ec837c82d7 ("imx6: wandboard: convert to DM_PMIC")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Add support for the EFI_RNG_PROTOCOL routines for the qemu arm64
platform. EFI_RNG_PROTOCOL is an uefi boottime service which is
invoked by the efi stub in the kernel for getting random seed for
kaslr.
The routines are platform specific, and use the virtio-rng device on
the platform to get random data.
The feature can be enabled through the following config
CONFIG_EFI_RNG_PROTOCOL
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Changed SPDX header to use /* instead of //.
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Since the coprocessor state is tracked in a backup register, there is
no more need for tracking it in an environment variable : remove it.
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Acked-by: Patrick Delaunay <patrick.delaunay@st.com>
Khadas VIM3L uses the same board layout as VIM3, but with an S905D3 chip
instead of A311D. Board config is derived from khadas-vim3_defconfig and
sei610_defconfig. README is based on README.khadas-vim3; the difference
is that VIM3L uses FIP files from the g12a folder in vendor sources not
the g12b folder.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[narmstrong: added vim3l readme into w400 MAINTAINERS]
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJeFDfVAAoJEB6zHgIOrC/IKfsH/2cUfXuc9IgA7L90L3g7htlS
zLAQSC8Xk0WbgbmBJh/lq6zFWj2Mu2yfkZqRzwN8bHkmOPq40F+pEAszVtjH77HM
FpSjMSDVWfNXuhmoiS571dehA0TGi1b2kknrAXqpOwVuMRncMCwaPi8yZYZSGlSV
VzMtguQxD0sZg4oMZVde3tCd41smPTPNDjzLZnXdLa0b09+EtW6enGuk3vzXlS/8
QUT68wUzkeoptJhf3pQ3BXNvkFwdNdYJ74uevDmkAYtvxyl10WNykcwYmH50Q9qq
9plF11EizmTHlj16rWpZLx66RP0s4pziKaeGMr6S8uln33Cr9N496wPqtuDBnvA=
=FYPj
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2020.04-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
First set of u-boot-atmel features for 2020.04 cycle
This feature set is a patch series from Tudor Ambarus which includes
parsing of the spi flash SFDP parser for SST flashes, and using those
tables to retrieve unique saved per device MAC address. This is then
used as base mac address on the SAMA5D2 Wireless SOM EK board.
Add socdk board support for Intel Agilex SoC
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
According to the SOM and reference board the clock
can be taken from the external pin or provided from
ENET_REF_CLK. Add a new function that make the proper
set according the board type.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Make easy to map fdt file to board in order to use
this information later to apply specific change to
specific board combination.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
When pmic_get() is used with DM the first parameter must be
the complete node name plus the unit address, so fix it
accordingly.
Reported-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
When pmic_get() is used with DM the first parameter must be
the complete node name plus the unit address, so fix it
accordingly.
Reported-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
When pmic_get() is used with DM the first parameter must be
the complete node name plus the unit address, so fix it
accordingly.
Reported-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The DDR firmware binaries are not part of the U-Boot source code, so
we should look for them in the build directory, where they need to be
copied to before building U-Boot.
The ATF binary is already fetched from the build directory, but the
README files for the i.MX8M EVKs claim that it needs to be copied to
the source directory (which is still true for in-tree builds, but not
in general). Therefore we also fix the READMEs to use the build
directory as the correct location for all additional binary files.
Sined-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Take over maintainership for colibri_imx6/imx6ull/t30/vf modules.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Stefan Agner <stefan.agner@toradex.com>
Take over maintainership for apalis_imx6 and colibri_imx6 modules.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
The Embedded Artists COM board is based on NXP i.MX7ULP.
It has a BD70528 PMIC from Rohm with discrete DCDC powering option and
improved current observability (compared to the existing NXP i.MX7ULP EVK).
Add the initial support for the board.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Note: gpio7_8 was never used for usb power regulator so we remove it here
Acked-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Signed-off-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
Sync the Linux Kernel 5.4-rc6 device tree for Phytec Phycore
SoM and Segin board based on imx6UL and imx6ULL.
Changes includes Phytec naming convention for the devicetree files.
Signed-off-by: Parthiban Nallathambi <parthitce@gmail.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Enable driver model for Video to remove the following
compile warning on CM-FX6 SOM based target:
===================== WARNING ======================
This board does not use CONFIG_DM_VIDEO Please update
the board to use CONFIG_DM_VIDEO before the v2019.07 release.
====================================================
This change introduced build error as shown:
LD u-boot
drivers/built-in.o: In function ipu_displays_init'
arm-linux-ld.bfd: BFD (GNU Binutils) 2.29.1 assertion fail elf32-arm.c:9509
Makefile:1621: recipe for target 'u-boot' failed
make: *** [u-boot] Error 1
The DM converted video driver calls ipu_displays_init
in its probe, which inturn calls relevant board_video_skip.
Defining ipu_displays_init in the board file fixes build error.
Target was compile tested, build was clean.
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
Make first step in DT/DM migration. Enable OF_CONTROL only for the main
U-Boot image for now.
Remove mmc_init_main() because board_mmc_init() is not called when
DM_MMC is enabled.
DM_MMC requires DM_GPIO for card-detect to work. That in turn makes gpio
request mandatory. Add code to request/free gpios in platform code.
MMC devices are now numbered according to DT. The SD card is 1, and eMMC
is 2. Account for that in board_mmc_get_env_dev(), BOOT_TARGET_DEVICES,
and has_emmc().
DM_MMC requires BLK. However, the (BLK && !DM_USB) combination disables
USB_STORAGE. Enable DM_USB to preserve USB functionality. Add also
DM_REGULATORS for the USB power controller. This allows us to drop
board_ehci_hcd_init() and setup_usb().
Runtime selection of DT is necessary because of the i.MX6QD vs i.MX6SDL
incompatibility. DT selection does not rely on GPIOs, since DM_GPIO
depends on DT. Instead, we take one "fully featured" DT of each variant.
That should be enough to boot from both SD card and eMMC.
Since we don't select the exact DT, override the generic
show_board_info() that shows the selected DT 'model' field.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Pass rtc_status via the device tree, instead of on kernel command line.
Additionally, the 2038 mitigation is reported, if applied successfully.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
DM for PCI pulls DM for ethernet that also needs other changes described
below to build u-boot and keep existing functionality - ability to update
MAC addresses of FEC ethernet adapter and I210 adapter connected to the
Marvell switch.
- fec_mxc driver with DM needs PHYLIB;
- configuration items are moved from ge_bx50v3.h to ge_bx50v3_defconfig;
- FEC is marked as eth0 because it is always present, so indices changed:
I210 are still probed in the same order;
- board_eth_init() was used by legacy ethernet, setup for enet iomux and
pcie is moved to the board_late_init();
- pci_init() is called from the board_late_init() to initiate PCI bus
probing, so I210 devices are propagated to the device tree;
Signed-off-by: Denis Zalevskiy <denis.zalevskiy@ge.com>
[Describe PHY reset in device tree]
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Use vidconsole for output to the LCD, now that DM_VIDEO is used. Write
white text on a black background, like before migrating to DM_VIDEO.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Fix GPIO reservation warning on code paths that do not need LVDS power.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Copy device trees from linux, keeping them as separate files for
each board to ease future sync.
Update board code to use generic bx50v3 dt initially, then select
the specific dt based on board detection.
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
This patch introduces support for i.MX28 based XEA board.
This board supports DM/DTS in U-Boot proper as well as DM aware drivers
in SPL (u-boot.sb) by using OF_PLATDATA.
More detailed information regarding usage of it can be found in
./board/liebherr/xea/README file.
U-Boot SPL 2019.10-rc1-00233-g6aa549f05c (Aug 12 2019 - 09:23:36 +0200)
Trying to boot from MMC1
MMC0: Command 8 timeout (status 0xf0344020)
mmc_load_image_raw_sector: mmc block read error
U-Boot 2019.10-rc1-00233-g6aa549f05c (Aug 12 2019 - 09:23:36 +0200)
CPU: Freescale i.MX28 rev1.2 at 454 MHz
BOOT: SSP SPI #3, master, 3V3 NOR
Model: Liebherr (LWE) XEA i.MX28 Board
DRAM: 128 MiB
MMC: MXS MMC: 0
Loading Environment from SPI Flash... SF: Detected n25q128a13 with page size 256 Bytes, erase size 64 KiB, total 16 MiB
OK
In: serial
Out: serial
Err: serial
Net:
Warning: ethernet@800f0000 (eth0) using random MAC address - ce:e1:9e:46:f3:a2
eth0: ethernet@800f0000
Hit any key to stop autoboot: 0
Signed-off-by: Lukasz Majewski <lukma@denx.de>
add DM_VIDEO support and remove now unneeded board
code. As we show a bmp logo on boot, call now
bmp_display() from board code and do not use
cfb_console anymore.
Signed-off-by: Heiko Schocher <hs@denx.de>
enable CONFIG_DM_SPI and CONFIG_DM_SPI_FLASH
and get rid of build removal warnings.
define CONFIG_GPIO_ENABLE_SPI_FLASH is not longer
needed, so remove it from config_whitelist.txt
Signed-off-by: Heiko Schocher <hs@denx.de>
Enable DM_GPIO, GPIO_HOG, LED and LED_GPIO as gpio
and LEDs are now defined in DTS. Enable also here
the pinctrl driver, so pinmux setup is also done.
Signed-off-by: Heiko Schocher <hs@denx.de>
add DM_SERIAL support for the aristainetos board, and
remove not used code from board code.
remove CONSOLE_OVERWRITE_ROUTINE.
Signed-off-by: Heiko Schocher <hs@denx.de>
as we switch to support DM and DTS, rework the existing
DTS trees. Change also Linux specific Device trees, goal
is to push this changes to linux.
Collect U-Boot specific changes in separate "*u-boot*" dts
files.
Signed-off-by: Heiko Schocher <hs@denx.de>
remove aristainetos-v2.c file, as we now want to
switch to DM/DTS support and have all board specific
code in one file. Goal is to setup differences
through DT.
Signed-off-by: Heiko Schocher <hs@denx.de>
Add device trees from Linux in preparation for driver model
conversions.
device tree files taken from Linux:
71ae5fc87c34: "Merge tag 'linux-kselftest-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest"
and added SPDX license identifier.
Signed-off-by: Heiko Schocher <hs@denx.de>
remove 2b version of aristainetos board, as it
is easier to make the DM / DTS port and introduce
the 2b board version again (also some more board
version).
Signed-off-by: Heiko Schocher <hs@denx.de>
Bring in the following merges:
commit 8fbbec12f7
Merge: 87f69f467a63618e71e8
Author: Tom Rini <trini@konsulko.com>
Date: Fri Jan 3 09:48:47 2020 -0500
Merge https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriq into next
- updates and fixes on ls1028a, lx2, ls1046a, MC-DPSPARSER support
commit 87f69f467a
Merge: c0912f9bbf4466b99703
Author: Tom Rini <trini@konsulko.com>
Date: Tue Dec 24 08:18:19 2019 -0500
Merge https://gitlab.denx.de/u-boot/custodians/u-boot-mpc85xx into next
- Enable DM driver on ppc/km boards
- Enable DM_USB for some of NXP powerpc platforms: P5040, T4240, T208x,
T104x, P4080, P2041, P2020, P1020, P3041
- Some updates in mpc85xx-ddr driver, km boards
commit c0912f9bbf
Merge: 533c9f5714a1d6dc3f84
Author: Tom Rini <trini@konsulko.com>
Date: Wed Dec 18 07:20:19 2019 -0500
Merge branch 'next' of https://gitlab.denx.de/u-boot/custodians/u-boot-x86 into next
- Various x86 common codes updated for TPL/SPL
- I2C designware driver updated for PCI
- ICH SPI driver updated to support Apollo Lake
- Add Intel FSP2 base support
- Intel Apollo Lake platform specific drivers support
- Add a new board Google Chromebook Coral
commit 533c9f5714
Merge: 553cb06887033e18b47b
Author: Tom Rini <trini@konsulko.com>
Date: Tue Dec 17 07:53:08 2019 -0500
Merge tag '20191217-for-next' of https://gitlab.denx.de/u-boot/custodians/u-boot-i2c into next
i2c: for next
- misc: i2c_eeprom:
Add partition support and add ability to query size
of eeprom device and partitions
- i2c common:
add support for offset overflow in to address and add
sandbox tests for it.
commit 553cb06887
Merge: f39abbbc53b4f98b3b16
Author: Tom Rini <trini@konsulko.com>
Date: Thu Dec 12 08:18:59 2019 -0500
Merge tag 'dm-next-13dec19' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm into next
buildman improvements including toolchain environment feature
sandbox unicode support in serial
The board_boot_order() function currenly assumes that the boot source
is MMC/eMMC, but this isn't true for the NAND devices.
This patch cleans up board_boot_order() to check for NAND, SD, ESD,
MMC or EMMC. Anything beyond these are not supported, so it will
default back to the serial downloader if any of those devices are not
available.
Fixes: 9fb50c68da ("ARM: imx6q_logic: Fix MMC2 booting")
Signed-off-by: Adam Ford <aford173@gmail.com>
Following the README instructions leads to a non-booting
U-Boot:
U-Boot SPL 2020.01-rc3-00070-g9a0cbae22a (Nov 25 2019 - 13:08:24 -0300)
PMIC: PFUZE100 ID=0x10
DDRINFO: start DRAM init
DDRINFO:ddrphy calibration done
DDRINFO: ddrmix config done
Normal Boot
Trying to boot from MMC2
(It hangs here)
Use the "imx_4.19.35_1.0.0" ATF branch instead, which
fixes such problem and allow the boot to complete again.
Suggested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Currently the following hang is observed when booting a imx6sx-sdb
board:
U-Boot 2020.01-rc5-00004-g643366bcd5 (Dec 19 2019 - 14:56:23 -0300)
CPU: Freescale i.MX6SX rev1.0 996 MHz (running at 792 MHz)
CPU: Extended Commercial temperature grade (-20C to 105C) at 32C
Reset cause: POR
Model: Freescale i.MX6 SoloX SDB RevB Board
Board: MX6SX SABRE SDB revA
DRAM: 1 GiB
initcall sequence bffd8514 failed at call 87804cc0 (err=-19)
### ERROR ### Please RESET the board ###
When pmic_get() is used with DM the first parameter must be
the complete node name plus the unit address.
Fix the pmic_get() parameter to fix the boot regression.
Tested on a imx6sx-sdb and imx6q-sabresd boards.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Not all CONFIG_FSL_ESDHC defines were properly replaced with
CONFIG_FSL_ESDHC_IMX, which broke U-boot proper booting on
Colibri iMX6 SoMs.
U-boot is stuck after this message:
Commercial temperature grade DDR3 timings, 64bit bus width.
Trying to boot from MMC1
Fixes: e37ac717d7("Convert to use fsl_esdhc_imx for i.MX platforms")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Enable DP_PWR signal to power the DP to HDMI converter cable.
Signed-off-by: Wen He <wen.he_1@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Current implementation to get board version through GPIO is
broken due to endianness issue hence it is not working for rev B
board.
Fix it to make it work for Rev A as well as Rev B boards
Signed-off-by: Pramod Kumar <pramod.kumar_1@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
We can use the existing CONFIG_SYS_CONFIG_NAME define for that and
remove the option. Also fix the boot string for all km83xx boards.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
CC: Priyanka Jain <priyanka.jain@nxp.com>
CC: Valentin Longchamp <valentin.longchamp@ch.abb.com>
Remove this from the board header files and move it to Kconfig. Also use
the correct default address for kmtegr1.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
CC: Priyanka Jain <priyanka.jain@nxp.com>
CC: Valentin Longchamp <valentin.longchamp@ch.abb.com>
Orangepi Zero Plus 2 is an open-source single-board computer, available
in two Allwinner SOC variants, H3 and H5. We add support for H3 variant
here, as the H5 is already supported.
H3 Orangepi Zero Plus 2 has:
- Quad-core Cortex-A7
- 512MB DDR3
- microSD slot and 8GB eMMC
- Debug TTL UART
- HDMI
- Wifi + BT
- OTG + power supply
Sync dts from linux v5.2 commit:
"ARM: dts: sunxi: h3/h5: Remove stale pinctrl-names entry"
(sha1: 75f9a058838be9880afd75c4cb14e1bf4fe34a0b)
Commit:
"ARM: dts: sun8i: h3: Refactor the pinctrl node names"
(sha1: a4dc791974e568a15f7f37131729b1a6912f4811)
has been avoided as it breaks U-Boot build.
Signed-off-by: Diego Rondini <diego.rondini@kynetics.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The SST26VF064BEUI spi-nor flash is programmed at the factory with a
globally unique address stored in the SFDP vendor parameter table and
it is permanently writeprotected. Retrieve the EUI-48 address and set it
as ethaddr env.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Add support for coral which is a range of Apollo Lake-based Chromebook
released in 2017. This also includes reef released in 2016, since it is
based on the same SoC.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present if CONFIG_SPL_GPIO_SUPPORT is enabled then the GPIO uclass
is included in SPL/TPL without any control for boards. Some boards may
want to disable this to reduce code size where GPIOs are not needed in
SPL or TPL.
Add a new Kconfig option to permit this. Default it to 'y' so that
existing boards work correctly.
Change existing uses of CONFIG_DM_GPIO to CONFIG_IS_ENABLED(DM_GPIO) to
preserve the current behaviour. Also update the 74x164 GPIO driver since
it cannot build with SPL.
This allows us to remove the hacks in config_uncmd_spl.h and
Makefile.uncmd_spl (eventually those files should be removed).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJd77jyAAoJEB6zHgIOrC/IyYUH/iAUH4wo5qnOBiQU+MJluaiu
D8tMiJH13eW4gWnAqdGrOE9Q763asHIMshQpLK+4eXe4f4mZQ7re4CRNcYJrULeY
2StsJzl4sn/H4P5EiRuUWjkB7wnGRDD6ArH3j1uMJN4lpwCB0ZbqMQZpjt3wI2H4
KuE42d/ll08Aj0AvwdusffLIxlw5M1Z94uQSHoC3UTkPYN4VD5zXgdxv5eH6PZWe
paWmHQ0g7fL4UnYGWa0Jpx10SZpcut06dTeVGpsGiEOhaJHvpjYd4JAs/TTUxhFx
d5ZRjo1fStYmBXQIblhPNlJQkW4cqa/B+81f5aZbN/1yCijJWS2G8anGtY2ikPs=
=f0dF
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-fixes-2020.01-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
- First set of u-boot-atmel fixes for 2020.01 cycle:
This set includes a small fix for gpio bank names, one for removing
unused headers (also touches some other boards), and a fix for the QSPI
env read on one of the boards.
Up to now we only update the DRAM banks when we are define
CONFIG_BCM2711. But our one binary approach uses a config that supports
BCM2837 and BCM2711. As a result we only see one gibibyte of RAM on
Raspberry Pi 4, even if it has more RAM.
Fix this by calling dram_init_banksize.
Fixes: 5694090670 ("ARM: defconfig: add unified config for RPi3 and RPi4")
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
To update the dram bank information from device-tree we use
fdtdec_decode_ram_size() which expectes the the size-cells and
address-cells to be defined in the memory node. For normal system RAM
these values are defined in the root node. When the values differ from
the default values defined in the spec, we can end up with wrong RAM
bank information.
Switch to the "standard" way to update the RAM bank information to
avoid this.
Fixes: 9de5b89e4c ("rpi4: enable dram bank initialization")
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
- Increase stack size to avoid a stack overflow during distro boot.
- Add hifive-unleashed-a00.dts for SIFIVE FU540.
- Add OF_SEPARATE support for SIFIVE FU540.
- Add SPL support for Andes AX25 AE350.
- Improve U-Boot SPL / OpenSBI smp boot flow for RISC-V.
To get memory size from device tree instead of
get_ram_size(). This can avoid memory access fault
in U-Boot proper after PMP configurations in OpenSBI.
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: KC Lin <kclin@andestech.com>
Cc: Alan Kao <alankao@andestech.com>
This patch provides four configurations which can support U-Boot SPL
to boot from RAM or FLASH and then boot FIT image including OpenSBI
FW_DYNAMIC firmware and U-Boot proper images from RAM or MMC boot devices.
With ae350_rv[32|64]_spl_defconfigs:
U-Boot SPL will be loaded by gdb or FSBL and runs in RAM in machine mode
and then load FIT image from RAM device on AE350.
With ae350_rv[32|64]_spl_xip_defconfigs:
U-Boot SPL can be burned into SPI flash and run in flash in machine mode
and then load FIT image from SPI flash or MMC device on AE350.
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: KC Lin <kclin@andestech.com>
Cc: Alan Kao <alankao@andestech.com>
Part of the env cleanup moved this out of the environment code and into
the net code. However, this helper is sometimes needed even when the net
stack isn't included.
Move the helper to lib/net_utils.c like it's similarly-purposed
string_to_ip(). Also rename the moved function to similar naming.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reported-by: Ondrej Jirman <megous@megous.com>
-----------------
- imx8qxp_mek: increase buffer sizes and args number
- Fixes for imx7ulp
- imx8mm: Fix the first root clock in imx8mm_ahb_sels[]
- colibri_imx7: reserve DDR memory for Cortex-M4
- vining2000: fixes and convert to ethernet DM
- imx8m: fix rom version check to unbreak some B0 chips
- tbs2910: Disable VxWorks image booting support
-----BEGIN PGP SIGNATURE-----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=L2zo
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20191209' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
Fixes for 2020.01
-----------------
- imx8qxp_mek: increase buffer sizes and args number
- Fixes for imx7ulp
- imx8mm: Fix the first root clock in imx8mm_ahb_sels[]
- colibri_imx7: reserve DDR memory for Cortex-M4
- vining2000: fixes and convert to ethernet DM
- imx8m: fix rom version check to unbreak some B0 chips
- tbs2910: Disable VxWorks image booting support
The board has both VDD_SOC_IN and VDD_ARM_IN rails connected to the same
PMIC rail, align the LDO voltages to avoid leaking inside the MX6SX SoC.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>
Ever since the conversion to DM PCI, the board was missing the PCIe DT
nodes, hence the PCI did not really work. Fill in the DT nodes and add
missing PCIe device reset.
Moreover, bring the PCIe power domain up before booting Linux. This is
mandatory to keep old broken vendor kernels working, as they do not do
so and depend on the bootloader to bring the power domain up.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>
Convert the board to ethernet DM support. Adjust board file accordingly,
as the board_eth_init() contains custom clock configuration required for
this board to work. Furthermore, enable FEC1 clock to make FEC1 work as
well.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>
Enable DRAM calibration in SPL to improve behavior of the board
in edge conditions of the thermal envelope of the board and make
it even more stable.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>
In preparation for use of DDR DRAM fine-tuning upon boot,
convert the board to SPL framework instead of using DCD
tables to bring up DRAM and pinmux.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>
i.MX 7's Cortex-M4 core can run from DDR and uses DDR memory for
the rpmsg communication. Both use cases need a fixed location of
memory reserved. For the rpmsg use case the reserved area needs
to be in sync with the kernel's hardcoded vring descriptor location.
Use the linux,usable-memory property to carve out 1MB of memory
in case the M4 core is running. Also make sure that the i.MX 7
specific rpmsg driver does not get loaded in case we do not carve
out memory.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
This is a core board named Core-PX30-JD4 with a mainboard from Firefly,
name it as firefly-px30 for now.
This board can re-use the dts of PX30, the only difference is the UART IO,
the firefly use UART2 M1 while evb use UART2 M0.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Add more clarity by changing the Kconfig entry name.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[trini: Re-run migration, update a few more cases]
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
This adds a general board file based on MT8518 SoCs from MediaTek.
Apart from the generic parts (cpu) we add some low level init codes
and initialize the early clocks.
This commit is adding the basic boot support for the MT8518 eMMC board.
Signed-off-by: mingming lee <mingming.lee@mediatek.com>
[trini: Migrate env location to defconfig, set ENV_IS_IN_MMC]
Signeed-off-by: Tom Rini <trini@konsulko.com>
We don't have full device-tree support in SPL yet - add an appropriate
U_BOOT_DEVICE() to the board file.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The DM family of DaVinci SoCs is no longer supported. Drop the
irrelevant code from the driver.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Several boards still unnecessarily included micrel.h but no longer
require it since the switch to Device Tree configuration.
Signed-off-by: James Byrne <james.byrne@origamienergy.com>
These functions do not use driver model but are still used. Move them to a
new eeprom.h header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This function can be dropped when all boards use driver model for PCI. For
now, move it into init.h with a comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
A number of board function belong in init.h with the others. Move them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move this function into init.h which seems to be designed for this sort
of thing. Also update the header to declare struct global_data so that it
can be included without global_data.h being needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move these functions into the command.h header file which is a better fit.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move these two functions into the irq_funcs.h header file. Also move
interrupt_handler_t as this is used by the irq_install_handler() function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
These functions are CPU-related and do not use driver model. Move them to
cpu_func.h
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
These functions belong in cpu_func.h. Another option would be cache.h
but that code uses driver model and we have not moved these cache
functions to use driver model. Since they are CPU-related it seems
reasonable to put them here.
Move them over.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
These functions belong in cpu_func.h since they do not use driver model.
Move them over. Don't bother adding comments since these functions should
be deleted.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This function belongs in time.h so move it over and add a comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
At present this function sits in its own file but it does not really
justify it. There are similar string functions in vsprintf.h, so move it
there. Also add the missing function comment.
Use the vsprintf.h include file explicitly where needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
These don't need to be in common.h so move them out.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Drop inclusion of crc.h in common.h and use the correct header directly
instead.
With this we can drop the conflicting definition in fw_env.h and rely on
the crc.h header, which is already included.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
We have an existing U-Boot header for the one function that this defines.
Use that instead of the linux/ one. Move over the nice comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This is only used by a few files so it should not be in the common header.
Move it out.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
The deadline for migration to CONFIG_DM is v2020.01. The VCT
baords would need an almost complete rewrite of all drivers to
support driver model.
Unless someone has access to the hardware and volunteers to do the migration,
the board should be scheduled for removal.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
- Device tree alignment on v5.4-rc4 for all stm32 boards
- Correct the eMMC pin configuration on stm32mp157c-ev1
- Add DFU and SPI-NAND support for stm32mp1 board
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl3dN0YACgkQ4rK92eCq
k3WlywgAisVONrdkoC345Kq1vQRcKGYxcWVd0IWkuK3QZ4KrMRQrhEqXhmR7OhWD
4YrAlgV6FEBTlacfKKsxaL7MJ3VK+h5YLvqoGzZS2Inmrx09v6rOofVTRevmB4Qz
SlIeUKVBijORmRi31I/WcLdiPgd3RR53wQgAugU3PUpuoUb1Z+sJdOreOkl5qGyZ
8aRgvG/if8afILXfH/a4IUuPboaVjaC5B20JCzX4M4ks8lHJ3atbtawgj/e41yYv
Ybq3QudM62g4SvTgJ5/1yqjQ4Oj8dkAY7JyAiXfHa9Kip7s16aBDFklDH7eR9v7F
IxyoYcFhuPADE7ApdWtij/y/KRS66Q==
=oVPG
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20191126' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- Solve warning for stih410-b2260
- Device tree alignment on v5.4-rc4 for all stm32 boards
- Correct the eMMC pin configuration on stm32mp157c-ev1
- Add DFU and SPI-NAND support for stm32mp1 board
The board_mmc_init() defined in board files is actually
doing same thing with the cpu_mmc_init() defined in
arch/arm/cpu/armv7/ls102xa/cpu.c. So drop it.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add read for OTP and PMIC NVM with alternates
on virtual DFU device.
Serie-cc: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This patch adds the support of the spi nand device in mtdparts command
and in dfu_alt_info.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Generate automatically dfu_alt_info for the supported device.
The simple command "dfu 0" allows to start the dfu stack on usb 0
for the supported devices:
- dfu mtd for nand0
- dfu mtd for nor0
- dfu mmc for SDCard
- dfu mmc for eMMC
- dfu ram for images in DDR
The DUF alternate use the "part", "partubi" and "mmcpart" options
to select the correct MTD or GPT partition or the eMMC hw boot partition.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
- fix boot banner on RPi3/4
- add support for one binary on RPi3/4
-----BEGIN PGP SIGNATURE-----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=4Z+A
-----END PGP SIGNATURE-----
Merge tag 'rpi-next-2020.01' of https://github.com/mbgg/u-boot
- add RPi4 upstream compatible to pinctrl
- fix boot banner on RPi3/4
- add support for one binary on RPi3/4
For bcm283x based on arm64 we also have to change the mm_region.
Add assign this in mach_cpu_init() so we can create now one binary
for RPi3 and RPi4.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
The fw_dtb_pointer was defined in the assembly code, which makes him
live in section .text_rest
Put that's not necessary, we can push the variable in the .data section.
This will prevent relocation errors like:
board/raspberrypi/rpi/rpi.c:317:(.text.board_get_usable_ram_top+0x8):
relocation truncated to fit: R_AARCH64_LDST64_ABS_LO12_NC against symbol
`fw_dtb_pointer' defined in .text section in board/raspberrypi/rpi/built-in.o
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
- Clean vid/pid in Kconfig and add fastboot for rk3399
- add 'u-boot, spl-fifo-mode' for mmc
- Use FIT generator for rk3229 optee and rk3368 ATF
- fan53555: add support for Silergy SYR82X and SYR83X
The RK3368 lion board ATF can use bl31.elf like RK3399 and get the FIT
source with generic FIT generator script at:
arch/arm/mach-rockchip/make_fit_atf.py
And then we can use 'BL31' environment to get the path of bl31.elf
instead of copy it into U-Boot folder.
CC: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
- In ARMv8 NXP Layerscape platforms we also need to make use of
CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
ENV_IS_IN_FLASH.
- Migrate all platforms.
Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
We can only configure and set the environment in SPL when we have a
particular environment location set that is not "nowhere" like it is in
SECURE_BOOT designs. Update the code to reflect that.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
These functions can only be built and used when we have
ENV_IS_IN_SPI_FLASH, use that as a guard.
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The board file has a build time check to ensure that we do not have the
redundant environment overwriting the factory data. However, using the
symbol CONFIG_ENV_SIZE_REDUND isn't strictly needed as that is always
the same as CONFIG_ENV_SIZE. Use CONFIG_ENV_SIZE instead so that we can
later drop CONFIG_ENV_SIZE_REDUND.
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Support tinker-s board. The board is equivalent of tinker board
except of emmc.
TODO:
- support of usb current burst when the board is powered from pc
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
ROC-RK3308-CC is a rk3308 based board designed by
Firelfy, with eMMC and 256MB DDR3 and RTL8188 Wifi
on board.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
rockpro64 needs to setup I/O domains in order for USB to work in u-boot.
Since we currently don't have a driver to do that, split it into its own
board file and initialize I/O domains here.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
roc-rk3399-pc_defconfig is committed in below
commit <8a681f4c5aa15db51ad0209734859c9fe7c29cfd> ("rockchip: rk3399:
Add ROC-RK3399-PC support")
which doesn't follow the existing defconfigs on rk3399.
So, rename as followed with other rk3399 defconfigs.
Cc: Levin Du <djw@t-chip.com.cn>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The px30 evb is an evaluation board for the px30 together with a dsi-
connected display. This adds board and config files for it.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
-------------------
i.MX8MN SoC support
ROM API image download support
i.MX8MM enet enabling
-----BEGIN PGP SIGNATURE-----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=sgCz
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20191105' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
u-boot-imx-20191105
-------------------
i.MX8MN SoC support
ROM API image download support
i.MX8MM enet enabling
- Add support for rockchip pmic rk805,rk809, rk816, rk817
- Add rk3399 board Leez support
- Fix bug in rk3328 ram driver
- Adapt SPL to support ATF bl31 with entry at 0x40000
- Fix the u8 type comparision with '-1'.
- Fix checkpatch warning for multi blank line and review signature.
Specification
- Rockchip RK3399
- LPDDR4
- TF sd scard slot
- eMMC
- M.2 B-Key for 4G LTE
- AP6256 for WiFi + BT
- Gigabit ethernet
- HDMI out
- 40 pin header
- USB 2.0 x 2
- USB 3.0 x 1
- USB 3.0 Type-C x 1
- TYPE-C Power supply
Commit details of rk3399-leez-p710.dts sync from linus tree for Linux 5.4-rc1:
"arm64: dts: rockchip: Add dts for Leez RK3399 P710 SBC"
(sha1: fc702ed49a8668a17343811ee28214d845bfc5e6)
Signed-off-by: Andy Yan <andyshrk@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Rename the CONFIG_SECURE_BOOT name to CONFIG_NXP_ESBC to avoid
conflicts with UEFI secure boot.
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
There is an option to enable the board detection for TI platforms.
If this is option is not set, there is no reason to set the EEPROM
bus address or chip address.
This patch makes both EEPROM_BUS_ADDRESS and EEPROM_CHIP_ADDRESS
depend on TI_I2C_BOARD_DETECT.
Signed-off-by: Adam Ford <aford173@gmail.com>
The PMIC enables power to the MMC card by default, but depending
on the state it was left when restarted, it's possible the MMC
may be powered down.
This patch patch explicitly tells the twl4030 to power the MMC.
Signed-off-by: Adam Ford <aford173@gmail.com>
This adds platform code and the device tree for the Phytium Durian Board.
The initial support comprises the UART and the PCIE.
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Steven Hao <liuhao@phytium.com.cn>
add DM PCI support on the socrates board.
use PCIE_FSL now.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
add socrates device tree from linux:
commit 71ae5fc87c34 ("Merge tag 'linux-kselftest-5.2-rc1' of
git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest")
and added SPDX license identifier.
Did not fix checkpatch warnings:
arch/powerpc/dts/socrates.dts:235: check: Please don't use multiple blank lines
arch/powerpc/dts/socrates.dts:238: error: code indent should use tabs where possible
Also, add me as board maintainer.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
with u-boot,dm-spl added for imx8qm-pm node, and SPL_SIMPLE_BUS enabled,
the bind and probe code in board file could be removed.
Also we need to enlarge SYS_MALLOC_F_LEN to avoid calloc fail.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This commit adds support for the brppt2 board. The board is based on the
i.mx6 dual-lite SoC.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Enable bd71837 pmic for i.MX8MM EVK board, need to set voltage for
DRAM and linux suspend voltage requirement.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
We are going to add i2c pmic support before dram could be used.
So we need enable clk driver earlier, so use spl_early_init
and move clock controller probe eariler to board_init_f.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Migrate to DM_VIDEO, update the device tree and remove code that is no
longer necessary.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
The mccmon6 has been used a "mixed" approach between SPL and
U-Boot proper sources.
This commit decoupes SPL and u-boot proper, which allows clear
distinction between those two code bases and facilitates
conversion to DM/DTS on this particular board.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This commit converts mccmon6's u-boot proper (in a single commit to avoid
build breaks) to use solely DM/DTS.
The DTS description of the mccmon6 has been ported from Linux kernel
(v4.20, SHA1: 8fe28cb58bcb235034b64cbbb7550a8a43fd88be)
Signed-off-by: Lukasz Majewski <lukma@denx.de>
In order for 'bmode emmc' to work, the eMMC needs to be initialized in the
SPL. This change initializes the eMMC as BOOT_DEVICE_MMC1 (index=0).
Signed-off-by: Claudius Heine <ch@denx.de>
The board_boot_modes contained the wrong values for the emmc entry.
The eMMC here is connected over a 8-bit bus.
This change allows to use the 'bmode emmc' command to boot from emmc.
Signed-off-by: Claudius Heine <ch@denx.de>
Introduce imx6ull-colibri-u-boot.dtsi for u-boot specific properties to
keep original imx6ull-colibri.dts in sync with Linux.
Move all contents of imx6ull-colibri.dts to imx6ull-colibri.dtsi +
additionally fix checkpatch warnings.
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Back in the day on early board samples built-in Digilent JTAG probe
was not functional so we used externally attached Ashling Opella-XD
probe. But now with production units everything works as expected and
so we anybody may enjoy readily avaialble built-in JTAG probe so
we specify Digilent oprion on MDB's command line example.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
At present some boards generate kwbimage.cfg in the source tree
during the build. This breaks buildman testing on some systems
where the source tree is read-only. Update makefile rules to
generate it in the build tree instead.
Note some other boards have the kwbimage.cfg file written in
advance, hence we need check if the file exists in the build
tree first, otherwise we fall back to one in the source tree.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
- bmips: various small fixes
- mtmips: add new drivers for clock, reset-controller and pinctrl
- mtmips: add support for high speed UART
- mtmips: update/enhance drivers for SPI and ethernet
- mtmips: add support for MMC
-----BEGIN PGP SIGNATURE-----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=6G/J
-----END PGP SIGNATURE-----
Merge tag 'mips-pull-2019-10-25' of git://git.denx.de/u-boot-mips
- bmips: add BCRM NAND support for BCM6368, BCM6328, BCM6362 and BCM63268 SoCs
- bmips: various small fixes
- mtmips: add new drivers for clock, reset-controller and pinctrl
- mtmips: add support for high speed UART
- mtmips: update/enhance drivers for SPI and ethernet
- mtmips: add support for MMC
In SPL, DDR should be made available by the end of board_init_f()
so that apis in board_init_r() can use ddr. Adding support for
triggering DDR initialization from board_init_f().
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdspnqAAoJEB6zHgIOrC/Ixi4IAJEEiCZPu6Z3fbkFX/Um7vCX
eMTltJN8nz4oiSi3xdx3ejueqWdW3F8VuCkHb0j0bVAhMlUlVgwCzfd0cD+D2iwS
jkrgzASNAr+JeYKYEdWqqfaUxOCd2qfuBu9EXlpvKQLWLt+KRfsOsHWcgR4bf095
aGCihvd/fKhKYUvbf5cEQnsWa3UwtsKk4Web5MKjxXx3p0iVNlu4KLd/vDWfTios
X1NqiO5ZjXNrDxyG6Aj8lgDXlE5kfeKaN/aCJU1/0U2cXm8JRu2w2dv1P/e/kU+j
NHIGzICAG4Lk/4gQTeuohJxLyvj7K3i1H12ik9Qeh4H1/5fsyybyltGUo7H443s=
=JYe3
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2020.01-b' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
Second set of u-boot-atmel features and fixes for 2020.01 cycle
This feature set includes Eugen's work on a new tiny flexcom driver and
eeprom mac retrieval for the sam9x60-ek board.
A64 OLinuXino board from Olimex has three variants with onboard eMMC:
A64-OLinuXino-1Ge16GW, A64-OLinuXino-1Ge4GW and A64-OLinuXino-2Ge8G-IND. In
addition, there are two variants without eMMC. One without eMMC and one with SPI
flash. This suggests the need for separate device tree for the three eMMC
variants.
The Linux kernel upstream has chosen to create and use a separate device tree
for the eMMC variants instead of adding eMMC support existing device tree. These
changes to Linux kernel are queued for Linux 5.4.
commit <02bb66b347ff8115f53948f86b884e008ba385b9> ("arm64: dts:
allwinner: a64: Add A64 OlinuXino board (with eMMC)")
This patch has been tested on A64-OLinuXino-1Ge16GW and is based on Linux
device-tree and a64-olinuxino_defconfig.
Signed-off-by: Sunil Mohan Adapa <sunil@medhas.org>
[jagan: updated linux-next commit details]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
board_early_init_f added by commit e6cc3b25d7
("arm: zynq: Wire watchdog internals") is no longer needed that's why
remove it also with Kconfig enabling.
Fixes: ccd063e981 ("watchdog: Move watchdog_dev to data section (BSS may not be cleared)")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Remove macros which use PM_SIP_SVC offset and convert invoke_smc() to
xilinx_pm_request() which do calculation with PM_SIP_SVC already.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
- Fix ramdisk_addr_r for stm32f746-disco
- Fix USB product id for stm32mp1
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl2wHd8ACgkQ4rK92eCq
k3UEBQgAkVeXgew8P7Z/ATK6jGArMWF+OGbh+Eveb1/vD1opcizyvVm4gxg/RRQA
+yDuXhd0fXoaug4okDXplJXg7j6YRVr2PUPVoGYMcaLOX4TUcXXf+6rYycC4mzVS
5vF5Fb9k+Wu/5rI+7y0IJH2zoAvLtEJ1+8vDwH3oCIBgsTYn54FwOXU76ni9NzA/
n5Gs8Xn09TJb5BtZ/CNdBYgJ+4bDystzhVTbmaAUYSX075wMl4+Dax9EZLwc5941
3Ix5yzsDRYObrLhvZgSr3EaVcoxa6y7E3488D9o5voPbDsO5XMXf72MVFjMGJClQ
03q2RP1rNnDYzfGvPTztWPpSvgxC0A==
=UmF/
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-2019-10-23' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- Disable CONFIG_NET flag for MCU STM32
- Fix ramdisk_addr_r for stm32f746-disco
- Fix USB product id for stm32mp1
Select the correct USB product id used by the download gadget
for ST stm32mp1 boards.
The board stm32mp1 select the correct product id, as defined in
http://www.linux-usb.org/usb.ids for the STMicroelectronics
vendor id = 0x0483 (CONFIG_USB_GADGET_VENDOR_NUM):
- dfu = 0xdf11 : STM Device in DFU mode
it is the value used by ROM code and reused for stm32prog
command
- fasboot = 0x0afb : Android Fastboot device
- others = 0x5720 (CONFIG_USB_GADGET_PRODUCT_NUM)
Mass Storage Device
it is used for UMS command / usb_dnl_ums
This patch avoid conflict when the same USB VID/PID is used for
ums, fastboot or dfu command (two different protocols associated
to the same PID).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
- add HDMI/CVBS display support for Amlogic G12A SoCs and SEI510 board
- add support for Amlogic A311D based Khadas VIM3
- add support for Amlogic S905X3 based SEI610 board, targeting Android support like SEI510
-----BEGIN PGP SIGNATURE-----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=g/kq
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20191018' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic
- document alternative libretech-cc installation methods, including upstream TF-A and opensource tools
- add HDMI/CVBS display support for Amlogic G12A SoCs and SEI510 board
- add support for Amlogic A311D based Khadas VIM3
- add support for Amlogic S905X3 based SEI610 board, targeting Android support like SEI510
Add separate config file to handle the different eMMC size on
the sei610 board.
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add support for the customer board SEI610 manufactured by SEI Robotics
with the following specifications:
- Amlogic S905X3 ARM Cortex-A55 quad-core SoC
- 2GB DDR4 SDRAM
- 10/100 Ethernet (Internal PHY)
- 1 x USB 3.0 Host
- 1 x USB Type-C DRD
- 1 x FTDI USB Serial Debug Interface
- eMMC
- SDcard
- Infrared receiver
- SDIO WiFi Module
Like it's SEI510 counterpart, the boot flow is designed to boot
Android AOSP built for the Yukawa Android device.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Derived from odroid-n2_defconfig and README.odroid-n2.
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
As already documented in this README, several binaries must be
glued together in order to boot the device.
Extend the documentation to cover the prebuilt binaries
(saving you the hassle of installing ancient cross-compilers),
and also mention the open source replacements for the encryption
tool (which is especially useful if you want to avoid requiring
32-bit x86 binaries in your build system).
Signed-off-by: Daniel Drake <drake@endlessm.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Enable the DM based GPIO driver for FU540-C000 SoC.
Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
U-Boot cannot be built for h2200_defconfig with CONFIG_DM=y.
The maintainer Lukasz Dalek suggested to remove the board.
https://lists.denx.de/pipermail/u-boot/2019-August/380685.html
Cc: Lukasz Dalek <luk0104@gmail.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
[trini: As this is the last non-toradex PXA board, update travis too]
Signed-off-by: Tom Rini <trini@konsulko.com>
-------------------
Travis: https://travis-ci.org/sbabic/u-boot-imx/builds/597498628
- logicpd pinmux
- i.MX7ULP: imx_ddr_size
- fixes Toradex i.MX6/i.MX7
- pico-imx7d
- tpc70 converted to DM
- New Board: meerkat96
- add HAB version command
- i.MX8 :
imx8: Jump from alias to OCRAM address at SPL init
imx8qm/qxp: Set SPL TEXT base to OCRAM base
-----BEGIN PGP SIGNATURE-----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=J8jd
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20191014' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
u-boot-imx-20191014
-------------------
Travis: https://travis-ci.org/sbabic/u-boot-imx/builds/597498628
- logicpd pinmux
- i.MX7ULP: imx_ddr_size
- fixes Toradex i.MX6/i.MX7
- pico-imx7d
- tpc70 converted to DM
- New Board: meerkat96
- add HAB version command
- i.MX8 :
imx8: Jump from alias to OCRAM address at SPL init
imx8qm/qxp: Set SPL TEXT base to OCRAM base
Use imx_ddr_size() to retrieve the total DDR size instead
of passing a hardcoded memory size.
imx_ddr_size() calculates the memory size based on the actual
MMDC registers values and is useful to detect misconfigurations,
so switch to this more robust approach.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Implementation of pmic_get() uses uclass_find_device_by_name(), which
behaviour was changed in 4213609cc7
("drivers: core: use strcmp when find device by name"). Now we have to
supply full node name with unit address.
Fixes boot issue:
U-Boot 2019.07-00788-g0ef6e69a1e-dirty (Jul 19 2019 - 15:27:02 +0300)
CPU: Freescale i.MX7D rev1.3 1000 MHz (running at 792 MHz)
CPU: Extended Commercial temperature grade (-20C to 105C) at 41C
Reset cause: POR
DRAM: 512 MiB
initcall sequence 9ffd3a4c failed at call 87803c61 (err=-19)
ERROR Please RESET the board
Fixes: 4213609cc7("drivers: core: use strcmp when find device by name")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
This patch converts the TPC70 to use driver model and device tree
description in both SPL and u-boot proper.
Notable changes (DM/DTS conversion):
- PINCTRL{_IMX6}
- DM_I2C
- enable 'regulator' and 'pmic' commands
- DM_MMC and BLK (USDHC)
- DM_ETH
- DM WDT (including SYSRESET)
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The TPC70 can boot from SD card (debug/development) and eMMC (production).
The board_boot_order() function provides a run time check for the device
from which one wants to boot (it is selected by GPIO pins setup).
Moreover, a fallback to SD card is provided if the detection is not
possible or working properly.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
With the OCRAM expanded to 256KB and the SPL_PINCTRL enabled with
-u-boot.dtsi entries to include the pinmuxing in SPL, the manual
code setting up the pinmux can go away.
This patch removes the legacy pinmuxing code from the board file.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
So we can get rid of legacy pci config code.
PCI_PNP is not required for this board, remove it to reduce the size of the
u-boot binary.
DM_PCI does not start the host controller automatically anymore. Do so
in preboot instead.
Signed-off-by: Soeren Moch <smoch@web.de>
The Meerkat96 board, based on the NXP i.MX7D SoC, is a member of
96Boards community and complies with all Consumer Edition board
specifications.
https://www.novtech.com/products/meerkat96.htmlhttps://www.96boards.org/product/imx7-96/
The initial supported/tested devices include:
- Debug serial
- SD
- USB Host (with Ethernet)
With these support, it's good enough for loading Linux Kernel from SD or
Ethernet over USB.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
At this point, all drivers that do not use CONFIG_BLK are past their
migration deadlines, so remove this config as it's no longer helpful and
hinders enhancing block drivers.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
AM335x-ICE boards contain the CDCE913 clock synthesizer, and their
reset crystal capacitance load value of 10pF is wrong leading into
lost packets in certain networking tests. Add DT data for this
device, and probe it from the board file to program the crystal
capacitance load value to 0pF to avoid any problems.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
AM43xx-IDK boards contain the CDCE913 clock synthesizer, and their
reset crystal capacitance load value of 10pF is wrong leading into
lost packets in certain networking tests. Add DT data for this
device, and probe it from the board file to program the crystal
capacitance load value to 0pF to avoid any problems.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
AM57xx-IDK boards contain the CDCE913 clock synthesizer, and their
reset crystal capacitance load value of 10pF is wrong leading into
lost packets in certain networking tests. Add DT data for this
device, and probe it from the board file to program the crystal
capacitance load value to 0pF to avoid any problems.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Print the board name and ver along with the DT Model.
While at it print the ver for all the detected daughter cards.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
- add BOARD_LATE_INIT function calls in board.c
- add swi_status detection in board.c
- mux: add guardian interfaces to single pinmux structure
- am33xx, kconfig: add BOARD_LATE_INIT for GUARDIAN board
Signed-off-by: Moses Christopher <BollavarapuMoses.Christopher@in.bosch.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
am65x ROM support booting over UART. And U-Boot built for am65x EVM
supports UART boot as well. Add the UART boot procedure into the README
also providing a corresponding example command sequence for execution
on a host PC.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
The EEPROM contains eth1 MAC address as well, use it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Update headers generated by quartus to the latest version.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
The company Samtec was merged into Softing, migrate the board over to
the new name and update copyright headers.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
- Rename existing FSP code to fsp1
- Add fsp2 directory in preparation to support FSP 2.0
- Various x86 platform codes update
- Various bug fixes and updates in dm core, sandbox and spl
With the reverting of a previous change to spl_boot_device,
this board needs a new solution to determining if we're booting
from MMC1 or MMC2.
This patch creates board_boot_order function which overrides the
standard, and returns not only MMC1, or MMC2, but also can fall
back to NAND or the serial downloader should other boot options
fail.
Signed-off-by: Adam Ford <aford173@gmail.com>
Since convert dm_video, unused code introduced, so remove this
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Reviewed-by: Otavio Salvador <otavio@ossystems.com.br>
CONFIG_SECURE_BOOT is too generic and forbids to use it for cross
architecture purposes. If Secure Boot is required for imx, this means to
enable and use the HAB processor in the soc.
Signed-off-by: Stefano Babic <sbabic@denx.de>
In order to call preloader_console_init from board_init_f when
DM_SERIAL is enabled, it neesd to call spl_early_init() to get early access
to DM and device tree.
This patch calls spl_early_init just before preloader_console_init()
and enables DM_SERIAL and SPL_DM_SERIAL.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Per the workflow found in crt0.S, we don't need to clear BSS in
board_init_f nor do we need to call board_init_r since that will be
done for us from main when we return from board_init_f.
This patch removes the unneeded function calls from board_init_f.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add instructions on how to boot mx6ul_14x14_evk_defconfig target
using the Serial Download Protocol.
Add examples from uuu and imx_usb_loader tools.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Update the ddrc Qos setting for B1 to align with B0's setting.
Correct the initial clock for dram_pll. This setting will be
overwrite before ddr phy training. Although there is no impact
on the dram init, we still need to correct it to eliminate
confusion.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Tested-by: Robby Cai <robby.cai@nxp.com>
board early initialize fec ethernet controller pinmux
only when FEC is enabled
Signed-off-by: Parthiban Nallathambi <pn@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
boot order was added to handle both SD and eMMC. But commit
14d319b1 introduced to handle both eMMC and SD globally.
Signed-off-by: Parthiban Nallathambi <pn@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
After u-boot.cnt is padded to flash.bin automatically by script,
no need to burn the image mannually, so drop the step.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Since recent splash changes common code for splashscreen logo
should be used instead of adding duplicated code under board
directories. mx6ul_9x9_evk and mx6ul_14x14_evk configurations
used old board specific logo code and do not link, fix them.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Peng Fan <peng.fan@nxp.com>
doc/README.mxs no longer exists. It has been renamed doc/imx/common/mxs.txt,
so fix the mx28evk README accordingly.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
The get_board_id() function was using the old gpio_* compatibility layer
to read HW and SW ID numbers encoded on the PCB board.
After this change the new dm_gpio* API is used for this purpose.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
After this change the display5's emergency gpio use dm_gpio* functions
instead of legacy ones (gpio*) to read its state.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The common.c file content can be safely moved to spl.c file after
performing the DM/DTS conversion for the U-Boot proper.
It contains the non DM/DTS setup code, which now is only used by SPL.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The DM/DTS support for SPI is disabled on purpose for SPL, as it is not
supported as of time of this conversion.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
After this commit the display5 device would use I2C driver supporting
driver model (DM_I2C).
The 'i2c' and 'eeprom' commands now use DM I2C drivers and initialize
on-bus devices according to device tree description.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This code uses HW difference on the USB_RESET pin (added PULL UP resistor
on the L333 rev) to distinguish between two BK4 HW revisions.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Add Falcon mode support, which allows the SPL to load and
jump to the Linux kernel directly, without the need of loading
U-Boot proper.
CONFIG_SPL_OS_BOOT=y needs to be passed in the defconfig
in order to use Falcon mode.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Add the initial support for the pico-imx6 variants.
DDR initialization is based on the TechNexion's U-Boot code.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
When CONFIG_SPL_OS_BOOT is selected, it is still convenient to be able
to escape from Falcon mode and boot to U-Boot proper.
Add a mechanism that allows booting in U-Boot proper when the
key 'c' is entered on console at boot time.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Improve the README by adding instructions on how to boot using
Falcon mode, which allows the SPL to load the kernel directly,
without using U-Boot proper.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
When CONFIG_SPL_OS_BOOT is selected, it is still convenient to be able
to escape from Falcon mode and boot to U-Boot proper.
Add a mechanism that allows booting in U-Boot proper when the
key 'c' is entered on console at boot time.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Sync the Falcon mode instructions with the ones fro pico-imx7d.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Add support for the VXT VL050-8048NT-C01 panel connected through
the 24 bit parallel LCDIF interface.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Because FIT could not be used for AHAB secure boot on i.MX8,
so switch to use container image that could let SPL verify
ATF and U-Boot with AHAB.
Enable HUSH_PARSER in defconfig to make run netboot could work.
Note: The AHAB related code has not been added.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Because FIT could not be used for AHAB secure boot on i.MX8,
so switch to use container image that could let SPL verify
ATF and U-Boot with AHAB.
Note: The AHAB related code has not been added.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The first stage of flash.bin is larger than 584 * 512, so when
writting u-boot.itb, some data will be override. Enlarge the
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR to fix boot.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Since the SD3.0 kernel driver needs M4 image support, this causes
problem for usb boot booting into kernel. To decouple the relationship,
we modify the FDT file in u-boot to disable SD3.0.
So the kernel won't depend on M4 image.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This prevents messages like
gpio@20a0000: get_value: error: gpio GPIO2_2 not reserved
when CONFIG_DM_GPIO is enabled.
Also, when CONFIG_DM_GPIO is enabled, checkboard is too
early to use gpio_get_value, so read it directly on failure.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Commit e37ac717d7 ("Convert to use fsl_esdhc_imx for i.MX platforms")
converted FSL_ESDHC to FSL_ESDHC_IMX, but the config check for
apalis_imx6 wasn't updated accordantly.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
Only one dtb is currently supported, so match with imx6-apalis.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
