add at least icache support for at91 based boards.
This speeds up NOR flash access on an at91sam9g15
based board from 15.2 seconds reading 8 MiB from
a SPI NOR flash to 5.7 seconds.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Adding new handoff for SDRAM ctrcfg.extratime1 which is
required for stable LPDDR2 operation. Since the board is
using DDR3, the handoff is set to default value 0.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Adding new handoff for SDRAM ctrcfg.extratime1 which is
required for stable LPDDR2 operation. Since the board is
using DDR3, the handoff is set to default value 0.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Adding new handoff for SDRAM ctrcfg.extratime1 which is
required for stable LPDDR2 operation. Since the board is
using DDR3, the handoff is set to default value 0.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Adding new handoff for SDRAM ctrcfg.extratime1 which is
required for stable LPDDR2 operation. Since the board is
using DDR3, the handoff is set to default value 0.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Adding new handoff for SDRAM ctrcfg.extratime1 which is
required for stable LPDDR2 operation. Since the board is
using DDR3, the handoff is set to default value 0.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Adding new handoff for SDRAM ctrcfg.extratime1 which is
required for stable LPDDR2 operation. Since the board is
using DDR3, the handoff is set to default value 0.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Adding new handoff for SDRAM ctrcfg.extratime1 which is
required for stable LPDDR2 operation. Since the board is
using DDR3, the handoff is set to default value 0.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Adding new handoff for SDRAM ctrcfg.extratime1 which is
required for stable LPDDR2 operation. Since the board is
using DDR3, the handoff is set to default value 0.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
i.CoreM6 Quad/Dual modules are system on module solutions
manufactured by Engicam with following characteristics:
CPU NXP i.MX6 DQ, 800MHz
RAM 1GB, 32, 64 bit, DDR3-800/1066
NAND SLC,512MB
Power supply Single 5V
MAX LCD RES FULLHD
and more info at
http://www.engicam.com/en/products/embedded/som/sodimm/i-core-m6s-dl-d-q
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add DM_GPIO, DM_MMC support for u-boot and disable for SPL.
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
i.CoreM6 DualLite/Solo modules are system on module solutions
manufactured by Engicam with following characteristics:
CPU NXP i.MX6 DL, 800MHz
RAM 1GB, 32, 64 bit, DDR3-800/1066
NAND SLC,512MB
Power supply Single 5V
MAX LCD RES FULLHD
and more info at
http://www.engicam.com/en/products/embedded/som/sodimm/i-core-m6s-dl-d-q
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Boot Log for i.CoreM6 DualLite/Solo Starter Kit:
-----------------------------------------------
U-Boot SPL 2016.09-rc2-30739-gd1fa290 (Sep 17 2016 - 00:37:46)
Trying to boot from MMC1
U-Boot 2016.09-rc2-30739-gd1fa290 (Sep 17 2016 - 00:37:46 +0530)
CPU: Freescale i.MX6SOLO rev1.3 at 792MHz
CPU: Industrial temperature grade (-40C to 105C) at 31C
Reset cause: POR
DRAM: 256 MiB
MMC: FSL_SDHC: 0
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc0 is current device
switch to partitions #0, OK
mmc0 is current device
reading boot.scr
** Unable to read file boot.scr **
reading zImage
6741808 bytes read in 341 ms (18.9 MiB/s)
Booting from mmc ...
reading imx6dl-icore.dtb
30600 bytes read in 19 ms (1.5 MiB/s)
Booting using the fdt blob at 0x18000000
Using Device Tree in place at 18000000, end 1800a787
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
Boot Log for i.CoreM6 Quad/Dual Starter Kit:
--------------------------------------------
U-Boot SPL 2016.09-rc2-30739-gd1fa290 (Sep 17 2016 - 00:37:46)
Trying to boot from MMC1
U-Boot 2016.09-rc2-30739-gd1fa290 (Sep 17 2016 - 00:37:46 +0530)
CPU: Freescale i.MX6Q rev1.2 at 792MHz
CPU: Industrial temperature grade (-40C to 105C) at 28C
Reset cause: POR
DRAM: 512 MiB
MMC: FSL_SDHC: 0
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot: 0
icorem6qdl>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add plugin code for mx6ullevk.
Define CONFIG_USE_IMXIMG_PLUGIN in defconfig file to use plugin code.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
This should be defined in a header file so that arguments are checked.
Move it to video.h.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Most armv8 systems have PSCI support enabled in EL3, either through
ARM Trusted Firmware or other firmware.
On these systems, we do not need to implement system reset manually,
but can instead rely on higher level firmware to deal with it.
The exclude list seems excessive right now, but NXP is working on
providing an in-tree PSCI implementation, so that all NXP systems
can eventually use PSCI as well.
Signed-off-by: Alexander Graf <agraf@suse.de>
[agraf: fix meson]
Reviewed-by: Simon Glass <sjg@chromium.org>
All systems that are running on armv8 are running bare metal with firmware
that implements PSCI running in EL3. That means we don't really need to expose
the hypercall variants of them.
This patch leaves the code in, but makes the code explicit enough to have the
compiler optimize it out. With this we don't need to worry about hvc vs smc
calling convention when calling psci helper functions.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a README to explain the steps for booting mx6sabresd in different ways:
1. Booting via Normal U-Boot (u-boot.imx)
2. Booting via SPL (SPL and u-boot.img)
3. Booting via Falcon mode (SPL launches the kernel directly)
Signed-off-by: Diego Dorta <diego.dorta@nxp.com>
Allow i.MX6Q Sabre SD to load the kernel and dtb via SPL in Falcon mode.
Based on the Falcon mode code for MX6 Gateworks Ventana board.
Signed-off-by: Diego Dorta <diego.dorta@nxp.com>
Declaring a CSF section makes the imximage tool increase the size of
data to be loaded by the BootROM and also adds a pointer to that CSF
section in the IVT header to the BootROM can check the signature.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
PBL flush command is restricted to CCSR memory space. So use WAIT
PBI command to provide enough time for data to get flush in
target memory.
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
[York Sun: rewrap commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
T series boards use unified RCW for sd, spi and nand boot.
Now split txxx_rcw.cfg to txxx_sd_rcw.cfg, txxx_spi_rcw.cfg
and txxx_nand_rcw.cfg for SPI/NAND/SD boot.
And modify RCW[PBI_SRC] for them:
PBI_SRC=5 for SPI 24-bit addressing
PBI_SRC=6 for SD boot
PBI_SRC=14 for IFC NAND boot
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Sometimes devicetree nodes and or properties are added out of the u-boot
console, maybe through some script or manual interaction.
The devicetree as loaded or embedded is quite small, so the devicetree
has to be resized to take up those new nodes/properties.
In original the devicetree was only extended by effective
4 * add_mem_rsv.
With this commit we can add an argument to the "fdt resize" command,
which takes the extrasize to be added.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Acked-by: Simon Glass <sjg@chromium.org>
Ethernet ports might be used in the kernel even if CPSW driver
is disabled at u-boot. So always set ethaddr and eth1addr
environment variable from efuse.
Retain usbnet_devaddr as it is required for SPL USB eth boot.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Both ethernet ports can be used as CPSW ethernet (RMII mode)
or PRU ethernet (MII mode) by setting the jumper near the port.
Read the jumper value and set the pinmux, external mux and
PHY clock accordingly.
As jumper line is overridden by PHY RX_DV pin immediately
after bootstrap (power-up/reset), we have to use GPIO edge
detection to capture the jumper line status.
As u-boot doesn't provide any infrastructure for GPIO edge
detection, we directly access the GPIO registers.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Create a Kconfig entry for DISPLAY_BOARDINFO and make it be the default
in certain architectures. Migrate all config files.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This patch adds a small README to explain the 2 defconfig files and its
usage for the different console UART options.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Synology DS109 is based on MV88F6281. The code
is based on Dreamplug code with modificatons
from Synologys open source repository.
Signed-off-by: Walter Schweizer <swwa@users.sourceforge.net>
Signed-off-by: Stefan Roese <sr@denx.de>
As a standard practice complex definitions should be protected
with parentheses, as it might fail when used in a complex if
statements.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add DTS support for dra72 evm Rev C which has the following
changes
* Two ethernet ports now instead of the single one in rev B.
* DP83867 ethernet phy instead of DP838865.
Cc: Vignesh R <vigneshr@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Commit f225d39d30 ("vexpress: Check TC2 firmware support before defaulting
to nonsec booting") added support to check if the firmware on TC2 is
configured appropriately before booting in nonsec/hyp mode.
However when booting in non-secure/hyp mode, CCI control must be done in
secure firmware and can't be done in non-secure/hyp mode. In order to
ensure that, this patch disables the cci slave port inteface so that it
is not accessed at all.
Cc: Jon Medhurst <tixy@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Jon Medhurst <tixy@linaro.org>
Tested-by: Jon Medhurst <tixy@linaro.org>
We now use device tree to provide SoC data to the UART driver, there
is no need for the legancy UART platform data.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Fix various misspellings of:
* deprecated
* partition
* preceding,preceded
* preparation
* its versus it's
* export
* existing
* scenario
* redundant
* remaining
* value
* architecture
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Stefan Roese <sr@denx.de>
At present there are two SPI functions only used by freescale which are
defined in the spi_flash.h header. One function name matches an existing
generic SPL function.
Move these into a private header to avoid confusion.
Arcturus looks like it does not actually support SPI, so drop the SPI code
from that board.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Delete CONFIG_SKIP_LOWLEVEL_INIT define in ls1021atwr.h and
ls1021aqds.h can let it run cpu_init_cp15 to enable i-cache. First
stage of u-boot can run faster after that. There is a description
about skip lowlevel init in board/freescale/ls1021atwr/README.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Update the API's for transition of Security Monitor states. Instead
of providing both initial and final states for transition, just
provide final state for transition as Security Monitor driver will
take care of it internally.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
[York Sun: Reformatted commit message slightly]
Reviewed-by: York Sun <york.sun@nxp.com>
PCM052 SoMs may be equipped with various sizes of DDR.
Keep default of 256MB; new PCM052-based targets will
specify their actual DDR size.
Linux command line is auto-adjusted to DDR size.
Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
Add i.MX6ULL EVK board support:
Add device tree file, which is copied from NXP Linux.
Enabled DM_MMC, DM_GPIO, DM_I2C, DM_SPI, PINCTRL, DM_REGULATOR.
The uart iomux settings are still keeped in board file.
Boot Log:
U-Boot 2016.09-rc1-00366-gbb419ef-dirty (Aug 11 2016 - 13:08:58 +0800)
CPU: Freescale i.MX6ULL rev1.0 at 396MHz
CPU: Commercial temperature grade (0C to 95C) at 15C
Reset cause: POR
Model: Freescale i.MX6 ULL 14x14 EVK Board
Board: MX6ULL 14x14 EVK
DRAM: 512 MiB
MMC: initialized IMX pinctrl driver
FSL_SDHC: 0, FSL_SDHC: 1
In: serial
Out: serial
Err: serial
Net: CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot: 0
=> mmc dev 1
switch to partitions #0, OK
mmc1 is current device
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
When using SPL on i.mx6 we frequently notice some DDR initialization
mismatches between the SPL code and the non-SPL code.
This causes stability issues like the ones reported at 7dbda25ecd
("mx6ul_14x14_evk: Pass refsel and refr fields to avoid hang") and also:
http://lists.denx.de/pipermail/u-boot/2016-September/266355.html .
As the non-SPL code have been tested for long time and proves to be reliable,
let's configure the DDR in the exact same way as the non-SPL case.
The idea is simple: just use the DCD table and write directly to the DDR
registers.
Retrieved the DCD tables from:
board/freescale/mx6sabresd/mx6q_4x_mt41j128.cfg
and
board/freescale/mx6sabresd/mx6qp.cfg
(NXP U-Boot branch imx_v2015.04_4.1.15_1.0.0_ga)
This method makes it easier for people converting from non-SPL to SPL code.
Other benefit is that the SPL binary size is reduced from 44 kB to 39.9 kB.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
A kernel hang is observed when running wandboard 3.14 kernel and
going to the lowest operational point of cpufreq:
# ifconfig eth0 down
# echo 1 > /sys/class/graphics/fb0/blank
The problem is caused by incorrect setting of the REFR field
of register MDREF. Setting it to 4 refresh commands per refresh
cycle fixes the hang.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
When CONFIG_FIT_IMAGE_POST_PROCESS or CONFIG_SPL_FIT_IMAGE_POST_PROCESS
is enabled board_fit_image_post_process will be called, add this
function to am33xx boards when CONFIG_TI_SECURE_DEVICE is set to
verify the loaded image.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
rockchip platform have a protocol to pass the the kernel reboot mode to bootloader
by some special registers when system reboot. In bootloader we should read it and take action.
We can only setup boot_mode in board_late_init becasue "setenv" need env setuped.
So add CONFIG_BOARD_LATE_INIT to common header and use a entry "rk_board_late_init"
to replace "board_late_init" in board file.
Signed-off-by: Jacob Chen <jacob2.chen@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
The latest rk3288-miniarm board doesn't have eMMC device, so remove it.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add vdd_center pwm regulator get_device to
enable this regulator.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
EEC is being enabled based on the ddr size populated by SPD data.
But not all keystone platforms have SPD data to detect ddr3 size.
So, enable ECC using the detected DDR size.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The function fdt_fixup_dr_usb is specific to fsl/nxp. So,
make the function name explicit and rename fdt_fixup_dr_usb
into fsl_fdt_fixup_dr_usb.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Commit ce02a71c23 "tegra: dts: Sync tegra20 device tree files with
Linux" enabled the ULPI USB port on Ventana, but made no attempt to ensure
that U-Boot code could handle this. In practice, various code is missing,
and various configuration options are not enabled, which causes U-Boot to
hang when attempting to initialize this USB port. This patch enables ULPI
PHY support on Ventana, and adds the required pinmux setup for the port to
operate. Note that Ventana is so similar to Seaboard that this change is
made in the Seaboard board file, which is shared with Ventana.
Seaboard also has the ULPI USB port wired up in hardware, although to an
internal port that often doesn't have anything attached to it. However,
the DT nodes for the USB controller and PHY had different status property
values, so the port was not initialized by U-Boot. Fix this inconsistency,
and enable the ULPI port, just like in the Linux kernel DT. This likewise
requires enabling ULPI support in the Seaboard defconfig.
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This patch adds basic support for the Marvell Armada 7K DB-88F7040
development board. Supported are the following interfaces:
- UART
- SPI (incl. SPI NOR)
- I2C
- USB
- SATA / AHCI
Support for other interfaces will follow.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
This patch adds basic support for the Marvell Armada 3700 DB-88F3720
development board. Supported are the following interfaces:
- UART
- SPI (incl. SPI NOR)
- I2C
- Ethernet
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Instead of using multiple macros, a data structure is used to pass
board-specific parameters to MMDC DDR driver.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This board is a plug in card for Marvell's switch system development
kits. Form-factor aside it is similar to the DB-88F6820-GP with the
following differences.
- TCLK is 200MHz
- SPI1 is used
- No SATA
- No MMC
- NAND flash
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Use a board-specific board_sat_r_get() function to configure the board
for PCIe 2.0 capability (e.g. 5GB/s link speed). Otherwise the default
of 2.5GB/s will be established.
Signed-off-by: Stefan Roese <sr@denx.de>
Now, arch/${ARCH}/include/asm/errno.h and include/linux/errno.h have
the same content. (both just wrap <asm-generic/errno.h>)
Replace all include directives for <asm/errno.h> with <linux/errno.h>.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Fixup include/clk.]
Signed-off-by: Tom Rini <trini@konsulko.com>
We are supposed to use #include <...> to include headers in the
public include paths. We should use #include "..." only for headers
in local directories.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
rk3399 using one gpio control signal for two usb 2.0 host port,
it's better to enable the power in board file instead of in usb driver.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
There is no interrupt line for each PWM which used by pinctrl to get the
periph_id, so it's not able to enable the default pinctrl setting by pinctrl
framework, let's enable it at board_init().
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Chip ID needs to be known for loading bitstream because
U-Boot checks ID from bitstream header in BIT format.
BIN format is completely unchecked.
The chipid is get from ATF via SMC.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
SPL needs to have bigger stack size because of USB.
Simple malloc needs to be disabled because dfu code requires different
allocation functions. There is no space in OCM that's why random place
in DDR is used.
BOOTD must be disabled because it is causing compilation error.
All variables are disabled and used only variables valid for DFU because
they are simple huge. Including automatic variables added by
CONFIG_ENV_VARS_UBOOT_CONFIG.
Hardcode addresses for u-boot, atf, kernel and dtb
just for SPL DFU code.
Enable SPL DFU for zcu100.
Create new usb_dfu_spl variable just to run Linux kernel loaded in SPL.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Function is defined in g_dnl.h and have different parameter
then it is used. This patch fixes it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch introduces support for building U-Boot to run on the MIPS
Boston development board. This is a board built around an FPGA & an
Intel EG20T Platform Controller Hub, used largely as part of the
development of new CPUs and their software support. It is essentially
the successor to the older MIPS Malta board.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Enable support for the MIPS Coherence Manager & L2 caches on the MIPS
Malta board, removing the need for us to attempt to bypass the L2 during
boot (which would fail with recent CPUs that expose L2 config via the CM
anyway).
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
MIPSfpga is an FPGA based dev platform.
In a nutshell, its a microAptiv cpu core with lots of Xilinx IP blocks
The FPGA dev board used is the Nexys4DDR board by Digilent.
For more information, check the Readme file in board/imgtec/xilfpga
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
There are a few boards that use CONFIG_ISO_STRING as part of a sanity
check during firmware update at run time. Move this string to Kconfig.
Signed-off-by: Tom Rini <trini@konsulko.com>
Convert CONFIG_MIP405T from SYS_EXTRA_OPTIONS to a real config
There are two boards, MIP405 and MIP405T that have a few differences.
Start by checking for CONFIG_TARGET_MIP405. Then introduce
CONFIG_TARGET_MIP405T and use that not CONFIG_MIP405T. Next, convert
also convert the usage of CONFIG_ISO_STRING to be based on Kconfig.
Signed-off-by: Tom Rini <trini@konsulko.com>
Move the config IDENT_STRING to Kconfig and migrate all boards
[sivadur: Migrate zynq boards]
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
[trini: Update configs, add some default to sunxi Kconfig]
Signed-off-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Acked-by: Simon Glass <sjg@chromium.org>
Changed 'Sandbox' to 'sandbox' in subject:
Signed-off-by: Simon Glass <sjg@chromium.org>
The NanoPi NEO is a simple h3 board with 512MB RAM, ethernet, one usb
and one usb OTG connector.
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
LS1046AQDS Specification:
-------------------------
Memory subsystem:
* 8GByte DDR4 SDRAM (64bit bus)
* 128 Mbyte NOR flash single-chip memory
* 512 Mbyte NAND flash
* 64 Mbyte high-speed SPI flash
* SD connector to interface with the SD memory card
Ethernet:
* Two XFI 10G ports
* Two SGMII ports
* Two RGMII ports
PCIe: supports Gen 1 and Gen 2
SATA 3.0: one SATA 3.0 port
USB 3.0: two micro AB connector and one type A connector
UART: supports two UARTs up to 115200 bps for console
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS1046ARDB Specification:
-------------------------
Memory subsystem:
* 8GByte DDR4 SDRAM (64bit bus)
* 512 Mbyte NAND flash
* Two 64 Mbyte high-speed SPI flash
* SD connector to interface with the SD memory card
* On-board 4G eMMC
Ethernet:
* Two XFI 10G ports
* Two SGMII ports
* Two RGMII ports
PCIe:
* PCIe1 (SerDes2 Lane0) to miniPCIe slot
* PCIe2 (SerDes2 Lane1) to x2 PCIe slot
* PCIe3 (SerDes2 Lane2) to x4 PCIe slot
SATA:
* SerDes2 Lane3 to SATA port
USB 3.0: one super speed USB 3.0 type A port
one Micro-AB port
UART: supports two UARTs up to 115200 bps for console
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This general MMDC driver adds basic support for Freescale MMDC
(Multi Mode DDR Controller). Currently MMDC is integrated on ARMv8
LS1012A SoC for DDR3L, there will be a update to this driver to
support more flexible configuration if new features (DDR4, multiple
controllers/chip selections, etc) are implimented in future.
Meantime, reuse common MMDC driver for LS1012ARDB/LS1012AQDS/
LS1012AFRDM.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The deep sleep function of LS1 platform, is mapped into PSCI system
suspend function, this patch adds implementation of it.
Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
As the access to serders protocol unselected PCIe controller will
hang. So disable the R/W permission to unselected PCIe controller
including its CCSR, IO space and memory space according to the
serders protocol field of RCW.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add this API to make the individual device is able to be set to
the specified permission.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Move forward the basic non-secure access enable operation, so the
subsequent individual device access permission can override it.
And collect the dispersed callers in board level, and then move
them to SoC level.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
sec_init() which was earlier called in misc_init_r()
is now done in board_init() before PPA init as SEC
block will be used during PPA image validation.
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Update the README to add support for K2G EVM. Also
- Add steps on how to use MMC boot
- Fix load address when using CCS
- Update build target to u-boot.bin from u-boot-dtb.bin as all ks2
platforms uses DT.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
When beagleboard-X15 is booted, we see the following log:
Unidentified board claims BBRDX15_ in eeprom header
This is because of the missing check for x15 (the default) and reports
an error for a valid board configuration. Fix the same.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Felipe Balbi has move on from TI and the current email ID is no longer
valid. So, replacing with Lokesh.
While at it, update missing config file which was untracked.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
We are supposed to not add config entries with only "default y"
in board/SoC Kconfig files.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Add ARCH_SUPPORT_PSCI as a non-configurable option that platforms
can select. Then, move CONFIG_ARMV7_PSCI, which is automatically
enabled if both ARMV7_NONSEC and ARCH_SUPPORT_PSCI are enabled.
Reviewed-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The PBIAS fixing is done in the MMC driver, and doing it in the
the board file conflicts with the driver causing intermittent
hangs on reboot. Remove this from the board file and let
the driver do it.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Remove the device definition from board file, update the driver with
the new compatible property and update config with necessary options.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
On the raspberry pi, you can disable the serial port to gain dynamic frequency
scaling which can get handy at times.
However, in such a configuration the serial controller gets its rx queue filled
up with zero bytes which then happily get transmitted on to whoever calls
getc() today.
This patch adds detection logic for that case by checking whether the RX pin is
mapped to GPIO15 and disables the mini uart if it is not mapped properly.
That way we can leave the driver enabled in the tree and can determine during
runtime whether serial is usable or not, having a single binary that allows for
uart and non-uart operation.
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
warp7 has two targets:
- warp7_defconfig: boots in non-secure mode
- warp7_secure_defconfig: boots in secure mode
Print the mode that is being used to help users to easily identify
which target is running on the board.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
To be in the safe side we need to enable the CCGR clocks prior
to calling arch_cpu_init().
Inspired by Tim Harvey's commit d783c2744f ("imx: ventana: fix boot to SD").
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Eric Nelson <eric@nelint.com>
Tested-by: Eric Nelson <eric@nelint.com>
Adjust DDR3 initialization done in SPL by comparing them against
the NXP DCD table.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Eric Nelson <eric@nelint.com>
When running a NXP 4.1 kernel with U-Boot mainline on a mx6ul-evk,
we observe a hang when going into the lowest operational point of cpufreq.
This hang issue does not happen on the NXP U-Boot version.
After comparing the SPL DDR initialization against the DCD table
from NXP U-Boot, the key difference that causes the hang is the
MDREF register setting:
DATA 4 0x021B0020 0x00000800
,which means:
REF_SEL = 0 --> Periodic refresh cycle: 64kHz
REFR = 1 ---> Refresh Rate - 2 refreshes
So adjust the MDREF initialization for mx6ul_evk accordingly
to fix the kernel hang issue at low bus frequency.
Reported-by: Eric Nelson <eric@nelint.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Eric Nelson <eric@nelint.com>
Currently MX6 SPL DDR initialization hardcodes the REF_SEL and
REFR fields of the MDREF register as 1 and 7, respectively for
DDR3 and 0 and 3 for LPDDR2.
Looking at the MDREF initialization done via DCD we see that
boards do need to initialize these fields differently:
$ git grep 0x021b0020 board/
board/bachmann/ot1200/mx6q_4x_mt41j128.cfg:DATA 4 0x021b0020 0x00005800
board/ccv/xpress/imximage.cfg:DATA 4 0x021b0020 0x00000800 /* MMDC0_MDREF */
board/freescale/mx6qarm2/imximage.cfg:DATA 4 0x021b0020 0x7800
board/freescale/mx6qarm2/imximage.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6qarm2/imximage_mx6dl.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6qarm2/imximage_mx6dl.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6qsabreauto/imximage.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6qsabreauto/mx6dl.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6qsabreauto/mx6qp.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6sabresd/mx6dlsabresd.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6sabresd/mx6q_4x_mt41j128.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6slevk/imximage.cfg:DATA 4 0x021b0020 0x00001800
board/freescale/mx6sxsabreauto/imximage.cfg:DATA 4 0x021b0020 0x00000800
board/freescale/mx6sxsabresd/imximage.cfg:DATA 4 0x021b0020 0x00000800
board/warp/imximage.cfg:DATA 4 0x021b0020 0x00001800
So introduce a mechanism for users to be able to configure
REFSEL and REFR fields as needed.
Keep all the mx6 SPL users in their current REF_SEL and REFR values,
so no functional changes for the existing users.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Eric Nelson <eric@nelint.com>
Register LDOGCTL contains only bit 0 as a valid bit, so there is no need
to do a read-modify-write operation.
Simplify the code by writing directly to this register.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Register LDOGCTL contains only bit 0 as a valid bit, so there is no need
to do a read-modify-write operation.
Simplify the code by writing directly to this register.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Register LDOGCTL contains only bit 0 as a valid bit, so there is no need
to do a read-modify-write operation.
Simplify the code by writing directly to this register.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
ft_board_setup may return early in the case that the board revision
cannot be obtained. In that case it is assumed that no revision
specific correction in the fdt is neccessary. But the mtd partitions
will not be fixed up either altough they are not revision specific.
Move the call to fdt_fixup_mtdparts in front of the revision specific
part to ensure that the partitions are fixed up even if the board
revision cannot be obtained.
While on it, fix a spelling mistake in a comment introduced by the
same commit.
Fixes: 62d6bac660 ("ARM: board: cm_fx6: fixup mtd partitions in the fdt")
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Nikita Kiryanov <nikita@compulab.co.il>
Only a single pad is changed to change sdhc2_dat3 from an
SDIO pin to and from GPIO4:5, so remove the array and use
the imx_iomux_v3_setup_pad() routine.
Signed-off-by: Eric Nelson <eric@nelint.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Since commit a13d3757f7 ("warp: Use imx_ddr_size() for calculating the
DDR size") warp board no longer boots.
The reason for the breakage is that the warp board is using the DDR
configuration from mx6slevk. A fundamental difference between warp and
mx6slevk is that warp only uses one DDR chip select while mx6slevk uses two.
The imx_ddr() function calculates the RAM size in runtime by reading the
values of registers MDCTL and MDMISC.
So in order to fix this warp boot issue, create a imximage DDR file specific
to warp, where the MDCTL register is configured to only activates a single
chip select.
Reported-by: Breno Lima <breno.lima@nxp.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
Add support for Advantech DMS-BA16 board. The board is based on Advantech
BA16 module which has a i.MX6D processor. The board supports:
- FEC Ethernet
- USB Ports
- SDHC and MMC boot
- SPI NOR
- LVDS and HDMI display
Basic information about the module:
- Module manufacturer: Advantech
- CPU: Freescale ARM Cortex-A9 i.MX6D
- SPECS:
Up to 2GB Onboard DDR3 Memory;
Up to 16GB Onboard eMMC NAND Flash
Supports OpenGL ES 2.0 and OpenVG 1.1
HDMI, 24-bit LVDS
1x UART, 2x I2C, 8x GPIO,
4x Host USB 2.0 port, 1x USB OTG port,
1x micro SD (SDHC),1x SDIO, 1x SATA II,
1x 10/100/1000 Mbps Ethernet, 1x PCIe X1 Gen2
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Cc: u-boot@lists.denx.de
Cc: sbabic@denx.de
mx7dsabresd has two targets:
- mx7dsabresd_defconfig: boots in non-secure mode
- mx7dsabresd_secure_defconfig: boots in secure mode
Print the mode that is being used to help users to easily identify
which target is running on the board.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Casting "int"s to pointers is only valid for 32-bit systems.
Add the appropriate pointer type cast to avoid a compiler warning
when compiling for AArch64.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
There is no "CONFIG_MACH_SUN50I_A64" in upstream U-Boot, so fix
the name to prevent the option to be enabled.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The Orange Pi Plus2E is an extended version of the Orange Pi Pc Plus,
with 2G RAM and an external gbit ethernet phy.
The dts file is identical to the one submitted to the upstream kernel,
except that it has the pending patch to enable the ethernet controller
squashed in, as u-boot already has sun8i-emac support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
A33-OLinuXino is A33 development board designed by Olimex LTD.
It has AXP223 PMU, 1GB DRAM, a micro SD card, one USB-OTG connector,
headphone and mic jacks, connector for LiPo battery and optional
4GB NAND Flash.
It has two 40-pin headers. One for LCD panel, and one for
additional modules. Also there is CSI/DSI connector.
The dts files are identical to the ones submitted to the upstream kernel.
Signed-off-by: Stefan Mavrodiev <stefan.mavrodiev@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The iNet D978 rev2 is a tablet board designed by iNet, which is intended to
use on 10" tablets with a appearance like Apple iPad. It has A33 SoC, 1GB
RAM, 8GB/16GB NAND, SDIO Wi-Fi, a MicroUSB port and a MicroSD slot.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The Colorado TK1 SOM is a small form factor board similar to the
Jetson TK1. The main differences lie in the pinmux, and in that the
PCIe controller is set to use in 4lanes+1lane, rather than 2+2.
The pinmux header here was generated from a spreadsheet provided by
Colorado Engineering using the tegra-pinmux scripts. The spreadsheet
was converted from v09 to v11 by me.
Signed-off-by: Peter Chubb <peter.chubb@data61.csiro.au>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This introduces two board defconfig files for generating EFI 32-bit
and 64-bit payloads, to run on QEMU x86 target.
With these in place, hopefully buildman will catch any build error
with EFI payload support on x86.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch add maintainer information for rk3399 evb.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Add a defconfig and dts file for the Empire Electronix M712 tablet, this
is a 7" A13 tablet, with micro-usb (otg), headphone and micro-sd slots on
the outside. It uses a Goodix gt811 touchscreen controller, a RTL8188CTV
wifi chip and a DMART06 (1238a4) accelerometer.
The dts file is identical to the one submitted to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add a defconfig and dts file for tablets using the generic inet-q972 PCB.
Tablets with this PCB feature a mini-hdmi output, micro-usb usb-host,
micro-usb usb-otg, 3.5mm headphone jack, a micro sd slot,
(mini) power-barrel and an usb wifi module.
This has been tested on a 9.7" 1024x768 qware qw tb9718-qhd tablet.
The dts files are identical to the ones submitted to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
To common use of rcar-gen2-common directory in the R-Car SoCs,
and change from rcar-gen2-common to rcar-common.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
BLANCHE is development board based on R-Car V2H SoC (R8A7792)
This commit supports the following periherals:
- SCIF, Ethernet, QSPI, MMC
Signed-off-by: Masakazu Mochizuki <masakazu.mochizuki.wd@hitachi.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Salvator-x is an entry level development board based on
R-Car H3 SoC (R8A7795). This commit supports SCIF only.
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
To common use of rcar-gen2-common directory in the R-Car SoCs, and change from
rcar-gen2-common to rcar-common.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This patch adds support for the BayTrail based theadorable-x86-dfi-bt700
board which uses the DFI BT700 BayTrail Qseven SoM on a custom baseboard.
The main difference to the DFI baseboard is, that it isn't equipped
with a Super IO chip and uses the internal HS SIO UART (memory mapped
PCI based) as the console UART.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This patch adds support for the DFI BayTrail BT700 QSeven SoM installed
on the DFI Q7X-151 baseboard. The baseboard is equipped with the Nuvoton
NCT6102D Super IO chip providing the UART as console.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This patch includes the following changes:
- Remove Designware I2C support from dts as its not used
- Configure SMBus PADs in dts
- Enable I2C commands and I2C support
- Configure SMSC2513 USB hub via SMBus upon startup
- Move environment location to match Minnowmax example
- Enhancement of the default environment
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Without PS/2 keyboard and mouse in the ASL file, Windows does not
see them. No problem for Linux as it probes keyboard and mouse via
the legacy 8042 I/O port.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add entry for the missing internal UART defconfig to the MAINTAINERS
file.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
CC: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The 'xtfpga' board is actually a set of FPGA evaluation boards that
can be configured to run an Xtensa processor.
- Avnet Xilinx LX60
- Avnet Xilinx LX110
- Avnet Xilinx LX200
- Xilinx ML605
- Xilinx KC705
These boards share the same components (open-ethernet, ns16550 serial,
lcd display, flash, etc.).
Signed-off-by: Chris Zankel <chris@zankel.net>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
The firmware on TC2 needs to be configured appropriately before booting
in nonsec mode will work as expected, so test for this and fall back to
sec mode if required.
Signed-off-by: Jon Medhurst <tixy@linaro.org>
Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>
Tested-by: Ryan Harkin <ryan.harkin@linaro.org>
Run scripts/coccinelle/net/mdio_register.cocci on the U-Boot code base.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Program vdd_core for Jetson TK1 to 1V, which is the max safe voltage for
ultra low temperature operations. vdd_cpu and vdd_gpu are already at 1V.
Signed-off-by: Bibek Basu <bbasu@nvidia.com>
(swarren: fixed comments to better match the code)
(swarren: moved board ifdef around data in header, made code generic)
(swarren: fixed typos in commit description)
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
p2771-0000 has a couple of PCIe ports; one physically x4 desktop PCI
connector (which may run at x2 electrically, depending on the board
version and configuration) and a x1 connection to the M.2 slot (which may
not be active, depending on the board version and configuration). This
change enables those.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Now that clock and reset drivers exist for Tegra186, we can enable the SD
card controller. Now that a BPMP I2C driver exists for Tegra186, we can
communicate with the PMIC to enable power to the SD card. Hook up the DT
content and board code required to make the SD card work.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Linux stopped the use of keyword 'boolean' in Kconfig.
Refer to commit 6341e62b212a2541efb0160c470e90bd226d5496 ("kconfig:
use bool instead of boolean for type definition attributes")
in Linux Kernel.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
These config targets were added well before the Kconfig migration began
as a way to demonstrate how to make these platforms work with cut down
features. At this point in time they no longer serve a good purpose so
remove them.
Signed-off-by: Tom Rini <trini@konsulko.com>
Miniarm is a rockchip rk3288 based development board, which has lots of
interface such as HDMI, USB, micro-SD card, Audio etc.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Enable fastboot feature on rk3036, please refer to doc/README.rockchip
for more detailed usage.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
As of now we have 2 flavors of ARC SDP boards:
1) AXS101 - with ARC770 in ASIC
2) AXS103 - with ARC HS38 in FPGA
Both options share exactly the same base-board and only differ with
CPU-tiles in use. That means all peripherals are the same (they are
implemented in FPGA on the base-board) and so generic board could be
used for both.
While at it:
* Recreated defconfigs with savedefconfig
* In include/configs/axs10x.h numerical sizes replaced with
defines from linux/sizes.h for better readability.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
ARCangel was one of the main development boards back in the day but
now it's gone and replaced by other boards like ARC SDP.
But we also used to have simulation platform very similar to ARCangel4
in terms of CPU settings as well as basic IO like UART. Even though
ARCangel4 is long gone now we have a replacement for simulation which is
a plain or stand-alone nSIM and Free nSIM.
Note Free nSIM is available for download here:
https://www.synopsys.com/cgi-bin/dwarcnsim/req1.cgi
And while at it:
* Finally switch hex numerical values in nsim.h to defines from
include/linux/sizes.h
* Add defconfigs with ARC HS38 cores
* Recreated all defconfigs with savedefconfig
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
It is confusing to mention MAKEALL when it is not the normal way of building
U-Boot anymore. Update the documentation to suit.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
It seems that bytes 13-14 of the SID / bytes 1-2 from word 3 of the SID
are always 0 on H3 making it a poor candidate to use as source for the
serialnr / mac-address, and the other non constant words (1 and 2) also
have quite a few bits which are the same for some boards,
This commits switches to using the crc32 of words 1 - 3 to get a
more unique value for the mac-address / serialnr.
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Corentin LABBE <clabbe.montjoie@gmail.com>
Cc: Amit Singh Tomar <amittomer25@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
On 2 of my H3 boards bytes 13-15 of the SID are all 0 leading to
the NIC specific bytes of the mac all being 0, which leads to the
boards not getting an ipv6 address from the dhcp server.
This commits adds a check to ensure this does not happen.
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Corentin LABBE <clabbe.montjoie@gmail.com>
Cc: Amit Singh Tomar <amittomer25@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
PopMetal is a rockchip rk3288 based board made by ChipSpark, which has
many interface such as HDMI, VGA, USB, micro-SD card, WiFi, Audio and
Gigabit Ethernet.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Fennec is a RK3288-based development board with 2 USB ports, HDMI,
micro-SD card, audio and WiFi and Gigabit Ethernet. It also includes
on-board 8GB eMMC and 2GB of SDRAM. Expansion connectors provides access
to display pins, I2C, SPI, UART and GPIOs.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
The 'evb-rk3288' is not a vendor name, change it to 'rockchip' which is
the real vendor name.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
RK3399 needs reserve 0x200000 at the beginning of DRAM, for ATF bl31.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
imx_ddr_size() can be used to calculate the DDR size in runtime.
By using this function we no longer need to define PHYS_SDRAM_SIZE.
Cc: Martin Donnelly <martin.donnelly@ge.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
imx_ddr_size() can be used to calculate the DDR size in runtime.
By using this function we no longer need to define PHYS_SDRAM_SIZE.
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Heiko Schocher <hs@denx.de>
imx_ddr_size() can be used to calculate the DDR size in runtime.
By using this function we no longer need to define PHYS_SDRAM_SIZE.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
This commit adds support for the Toradex Computer on Modules
Colibri iMX7S/iMX7D. The two modules/SoC's are very similar hence
can be easily supported by one board. The board code detects RAM
size at runtime which is one of the differences between the two
boards. The board also uses the UART's in DTE mode, hence making
use of the new DTE support via serial DM.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
It's not necessary to implement the is_mx6q function, there is a macro in
sys_proto.h already implemented.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
It's not necessary to implement the is_mx6q function, there is a macro in
sys_proto.h already implemented.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
It's not necessary to use the is_cpu_type function, there is a macro in
sys_proto.h already implemented.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Added removal of the fsl,ext-reset-output property in the wdog node for board
revisions that pre-date the addition of the external watchdog reset signal.
This property is a recent addition to mainline linux kernel in order to
specify that the IMX watchdog external reset should be used instead of the
internal chip-level reset.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Re-factor the board-specific dt fixups so that they are easier to follow
and extend in the future:
- use defines for DT paths
- use switch/case per board
- order models numerically
There is no functional change in the code
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The hwconfig env var allows user to control hardware specific configuration
of board specific features but not all Ventana boards have the same features.
We will use the magic default value of "_UNKNOWN_" to signify that the
bootloader should create this based on detected board model.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Ventana boards with a PCI Marvell Sky2 GigE MAC require the MAC address to
be placed in a DT node in order for the mainline linux driver to obtain it.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The GW16082 mini-PCI expansion mezzanine uses a TI XIO2001 PCIe-to-PCI
bridge with legacy INTA/B/C/D interrupts. These interrupts are assigned
in the reverse order according to the PCI spec.
If the TI bridge is found on the Ventana PCI bus, add device-tree nodes
according to bus enumeration explicitly defining the interrupt mapping
to override the default PCI mapping in the Linux kernel. This allows
the GW16082 to work with upstream kernels that support device-tree
irq parsing.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
There is a new Orange Pi PC *Plus* version available now,
this is an extended version of the regular Orange Pi PC
with sdio wifi and an eMMC.
The upstream kernel devs have decided that they want a separate
dts for the PC Plus rather then sharing a single dts between the
regular PC and the PC Plus. So add a new orangepi_pc_plus_defconfig
to match.
The added dts file matches the one submitted to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
QSPI and IFC are pin-multiplexed on LS1043AQDS board. If QSPI is
enabled, IFC would not be initialized correctly. So disable the IFC
node for Linux.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch implements PSCI functions for ls102xa SoC following PSCI v1.0,
they are as the list:
psci_version,
psci_features,
psci_cpu_suspend,
psci_affinity_info,
psci_system_reset,
psci_system_off.
Tested on LS1021aQDS, LS1021aTWR.
Signed-off-by: Wang Dongsheng <dongsheng.wang@nxp.com>
Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add SD secure boot target for ls1021atwr.
Implement board specific spl_board_init() to setup CAAM stream ID and
corresponding stream ID in SMMU. Change the u-boot size defined by a
macro for copying the main U-Boot by SPL to also include the u-boot
Secure Boot header size as header is appended to u-boot image. So header
will also be copied from SD to DDR.
Reviewed-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
Override jump_to_image_no_args function to include validation of
u-boot image using spl_validate_uboot before jumping to u-boot image.
Also define macros in SPL framework to enable crypto operations.
Reviewed-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
Add a README to guide people flash the ATF and U-Boot
with Rockchip tools to bring up to board.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
RK3399 is a SoC from Rockchip with dual-core Cortex-A72
and quad-core Cortex-A53 CPU. It supports two USB3.0
type-C ports and two USB2.0 EHCI ports. Other interfaces
are very much like RK3288, the DRAM are 32bit width address
and support address from 0 to 4GB-128MB range.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
The 'evb_rk3036' and 'kylin' is not a vendor name, let's replace them
to 'rockchip' which is a real _vendor_ name, and meet the architecure
'board/<vendor>/<board-name>/'.
More boards from rockchip like evb_rk3288, evb_rk3399 will comes later.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Eddie Cai <eddie.cai.kernel@gmail.com>
evb-3288 board RK3288-based development board with 2 USB ports, HDMI,
VGA, micro-SD card, audio, WiFi and Gigabit Ethernet. It also includes
on-board 8G eMMC and 2GB of SDRAM. Expansion connector provide access to
display pins, I2C, SPI, UART and GPIOs. This add some basic files
required to allow the board to output serial messaged and can run
command(mmc info etc).
evb-rk3288 also supports booting from eMMC or SD card, the default is eMMC.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Sandbox is built with 64-bit ints by default. This doesn't work properly on
32-bit machines.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
We already have an SPL driver for the sunxi NAND controller, now add
the normal/standard one.
The source has been copied from Linux 4.6 with a few changes to make
it work in u-boot.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
On most platforms the print_fpga_state function is never called. Only
on dlvision-10g do we, so in that case inline it. Drop it from
everywhere else to avoid extra strings.
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Reinhard Pfau <reinhard.pfau@gdsys.cc>
Acked-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Per Vikas' request, the problem this commit is supposed to be solving is
something he doesn't see and further this introduces additional hardware
requirements.
This reverts commit 4b2fd720a7.
Signed-off-by: Tom Rini <trini@konsulko.com>
For mpc85xx SoCs, the core begins execution from address 0xFFFFFFFC.
In non-secure boot scenario from NAND, this address will map to CPC
configured as SRAM. But in case of secure boot, this default address
always maps to IBR (Internal Boot ROM).
The IBR code requires that the bootloader(U-boot) must lie in 0 to 3.5G
address space i.e. 0x0 - 0xDFFFFFFF.
For secure boot target from NAND, the text base for SPL is kept same as
non-secure boot target i.e. 0xFFFx_xxxx but the SPL U-boot binary will
be copied to CPC configured as SRAM with address in 0-3.5G(0xBFFC_0000)
As a the virtual and physical address of CPC would be different. The
virtual address 0xFFFx_xxxx needs to be mapped to physical address
0xBFFx_xxxx.
Create a new PBI file to configure CPC as SRAM with address 0xBFFC0000
and update DCFG SCRTACH1 register with location of Header required for
secure boot.
The changes are similar to
commit 467a40dfe3
powerpc/mpc85xx: SECURE BOOT- NAND secure boot target for P3041
While P3041 has a 1MB CPC and does not require SPL. On T104x, CPC
is only 256K and thus SPL framework is used.
The changes are only applicable for SPL U-Boot running out of CPC SRAM
and not the next level U-Boot loaded on DDR.
Reviewed-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
As part of Chain of Trust for Secure boot, the SPL U-Boot will validate
the next level U-boot image. Add a new function spl_validate_uboot to
perform the validation.
Enable hardware crypto operations in SPL using SEC block.
In case of Secure Boot, PAMU is not bypassed. For allowing SEC block
access to CPC configured as SRAM, configure PAMU.
Reviewed-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
Rev A03 of P2180 requires some PMIC programming adjustments, yet the
PMIC's own OTP has not been updated. Consequently, U-Boot must make
these changes itself.
NVIDIA's syseng team has confirmed that these changes can be enabled on
all board revisions without issue.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The PPA use PSCI to make secondary cores bootup. So when PPA was
enabled, add the CONFIG_ARMV8_PSCI to identify the SMP boot-method
between PSCI and spin-table.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The cm-fx6 module has an on-board st,m25p compatible spi flash chip
used for U-Boot (binary & environment). Overwrite the partitions in
the device tree by the partition table provided in the mtdparts
environment variable, if it is set.
This allows to specify a kernel independent partitioning in the
environment and provides a convient way for the user to adapt the
partition table.
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Introduce virtual and physical addresses in the mapping table. This change
have no impact on existing boards because they all use idential mapping.
Signed-off-by: York Sun <york.sun@nxp.com>
Secure_ram variable was put in generic global data. But only ARMv8
uses this variable. Move it to ARM specific data structure.
Signed-off-by: York Sun <york.sun@nxp.com>
The Orange Pi Lite SBC is a small H3 based SBC, with 512MB RAM,
micro-sd slot, HDMI out, 2 USB-A connectors, 1 micro-USB connector,
sdio attached rtl8189ftv wifi and an ir receiver.
The dts file is identical to the one submitted to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Now that we know that the BROM stores a value indicating the boot-source
at the beginning of SRAM, use that instead of trying to recreate the
BROM's boot probing.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
We always define CONFIG_MISC_INIT_R on sunxi and misc_init_r is never
called in the spl, so the linker will optimize it and parse_spl_header(),
of which it is the only caller, away.
On the tests I've done (Orange Pi PC build) the SPL actually becomes
8 bytes smaller with this patch.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Currently we fill ethaddr with a fixed unique address based on the SoCs
serial (from the sid) to make sure that boards which use the integrated
emac / gmac get a fixed mac rather then a random one.
On some boards the wifi does not come with a fixed mac either, so we need
to also set eth1addr.
This commit changes the ethaddr setting code to check for ethernet%d
aliases (as fdt_fixup_ethernet does) and set an ethaddr variable for
all present aliases.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The patch converts one of the "reserved" fields in the sunxi SPL
header to a fel_uEnv_length entry. When booting over USB ("FEL
mode"), this enables the sunxi-fel utility to pass the string
length of uEnv.txt compatible data; at the same time requesting
that this data be imported into the U-Boot environment.
If parse_spl_header() in the sunxi board.c encounters a non-zero
value in this header field, it will therefore call himport_r() to
merge the string (lines) passed via FEL into the default settings.
Environment vars can be changed this way even before U-Boot will
attempt to autoboot - specifically, this also allows overriding
"bootcmd".
With fel_script_addr set and a zero fel_uEnv_length, U-Boot is
safe to assume that data in .scr format (a mkimage-type script)
was passed at fel_script_addr, and will handle it using the
existing mechanism ("bootcmd_fel").
Signed-off-by: Bernhard Nortmann <bernhard.nortmann@web.de>
Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
It is useful to be able to build SPL for sandbox. It provides additional
build coverage and allows SPL features to be tested in sandbox. However
it does not need worthwhile to always create an SPL build. It nearly
doubles the build time and the feature is (so far) seldom used.
So for now, create a separate build target for sandbox SPL. This allows
experimentation with this new feature without impacting existing workflows.
Signed-off-by: Simon Glass <sjg@chromium.org>
This change is to remove a halt at about 200KiB
while sending a large(1MiB) binary to a micro controller using USART1.
USART1 is connected to a PC via an on-board ST-Link debugger
that also functions as a USB-Serial converter.
However, it seems to loss some data occasionally.
So I changed the serial port to USART6 and connected it to the PC using
an FTDI USB-Serial cable, therefore the transmission was successfully
completed.
Signed-off-by: Toshifumi NISHINAGA <tnishinaga.dev@gmail.com>
This patch adds SDRAM support for stm32f746 discovery board.
This patch depends on previous patch.
This patch is based on STM32F4 and emcraft's[1].
[1]: https://github.com/EmcraftSystems/u-boot
Signed-off-by: Toshifumi NISHINAGA <tnishinaga.dev@gmail.com>
Modify the SPL build procedure for AM437x high-security (HS) device
variants to create a secure u-boot_HS.img FIT blob that contains U-Boot
and DTB artifacts signed (and optionally encrypted) with a TI-specific
process based on the CONFIG_TI_SECURE_DEVICE config option and the
externally-provided image signing tool.
Also populate the corresponding FIT image post processing call to be
performed during SPL runtime.
Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Modify the SPL build procedure for AM57xx and DRA7xx high-security (HS)
device variants to create a secure u-boot_HS.img FIT blob that contains
U-Boot and DTB artifacts signed with a TI-specific process based on the
CONFIG_TI_SECURE_DEVICE config option and the externally-provided image
signing tool.
Also populate the corresponding FIT image post processing call to be
performed during SPL runtime.
Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Define a default board_run_command() function. This function contains
the commands needed to boot the board when CLI is disabled (CONFIG_CMDLINE=n).
Signed-off-by: Andrej Rosano <andrej@inversepath.com>
Add USB host support.
Tested by connecting a USB pen drive:
=> usb start
starting USB...
USB0: Port not available.
USB1: USB EHCI 1.00
scanning bus 1 for devices... 2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Add a README file to help users to install U-boot binary into the eMMC.
Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Pico-imx6ul has a KSZ8081 Ethernet PHY.
Add support for it.
Signed-off-by: Diego Dorta <diego.dorta@nxp.com>
Acked-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Instead of passing the total RAM size via PHYS_SDRAM_SIZE option,
we should better use imx_ddr_size() function, which automatically
determines the RAM size.
Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Instead of passing the total RAM size via PHYS_SDRAM_SIZE option,
we should better use imx_ddr_size() function, which automatically
determines the RAM size.
Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Instead of passing the total RAM size via PHYS_SDRAM_SIZE option,
we should better use imx_ddr_size() function, which automatically
determines the RAM size.
Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Instead of passing the total RAM size via PHYS_SDRAM_SIZE option,
we should better use imx_ddr_size() function, which automatically
determines the RAM size.
Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Acked-by: Fabio Estevam <fabio.estevam@nxp.com>
Custom Board based on MX6 Dual, 1GB RAM and eMMC.
There are two variants of the board with and without
PCIe (ZC5202 and ZC5601).
Signed-off-by: Stefano Babic <sbabic@denx.de>
Old revisions of Utilite (based on cm-fx6) do not have a dedicated
card detect pin. But the card is removable by the user and card
detection can be realized with polling (e.g. supported by Linux).
Add the broken-cd property to the mmc device tree instead of the
non-removable property to make card detection possible if polling
is supported.
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
Add support for Advantech SOM-DB5800 with the SOM-6867 installed.
This is very similar to conga-qeval20-qa3-e3845 in that there is a
reference carrier board (SOM-DB5800) with a Baytrail based SoM (SOM-6867)
installed.
Currently supported:
- 2x UART (From ITE EC on SOM-6867) routed to COM3/4 connectors on
SOM-DB5800.
- 4x USB 2.0 (EHCI)
- Video
- SATA
- Ethernet
- PCIe
- Realtek ALC892 HD Audio
Pad configuration for HDA_RSTB, HDA_SYNC, HDA_CLK, HDA_SDO
HDA_SDI0 is set in DT to enable HD Audio codec.
Pin defaults for codec pin complexs are not changed.
Not supported:
- Winbond Super I/O (Must be disabled with jumpers on SOM-DB8500)
- USB 3.0 (XHCI)
- TPM
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This patch adds support to enable and use the internal BayTrail UART
instead of the one integrated in the Super IO Winbond chip. For this,
a 2nd defconfig file is added.
This is useful for tests done for the congatec SoM used on baseboards
without such a Super IO chip.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Since we lack information about the DRAM initialization for the
Allwinner A64 SoC, booting any A64 based board like the Pine64 is a bit
involved at the moment.
Add a README file to explain the process.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Move to board/sunxi/ from doc/]
Signed-off-by: Tom Rini <trini@konsulko.com>
The Parrot Board is an evaluation board with an Allwinner R16 (assumed
to be close to an Allwinner A33), 4GB of eMMC, 512MB of RAM, USB host
and OTG, a WiFi/Bluetooth combo chip, a micro SD Card reader, 2
controllable buttons, an LVDS port with separated backlight and
capacitive touch panel ports, an audio/microphone jack, a camera CSI
port, 2 sets of 22 GPIOs and an accelerometer.
The DTS file is identical to the one submitted to the upstream kernel.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The switch to simple_printf was causing the SPL dram info to show as:
DRAM: u MiB
This fixes this by switching from %lu to %d for printing the DRAM size.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Align the name of the defconfig file for high-security (HS) device variants
from the AM43xx family of SoCs with the corresponding name used for the
general purpose devices. This allows for easier cross-association of those
files and also provides room to grow from an HS device part number
perspective.
Furthermore, update and cleanup associated MAINTAINERS file.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Madan Srinivas <madans@ti.com>
Not only am335x supports booting from NOR, i.MX6 SoCs also
supports booting from NOR. Make NOR_BOOT a common
option to let different SoCs share it.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Christophe Ricard <christophe-h.ricard@st.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Francois Retief <fgretief@spaceteq.co.za>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
add DM and DTS support for the at91 based siemens
boards.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
[rebased on current ToT]
Signed-off-by: Andreas Bießmann <andreas@biessmann.org>
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
[rebased on current ToT]
Signed-off-by: Andreas Bießmann <andreas@biessmann.org>
There is no more define of CONFIG_SYS_HUSH_PARSER. Rename some
remaining references and drop the backward compatible Kconfig entry.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
s/hardkernel/amlogic/ to have a single place for all the amlogic-based
boards.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Acked-by: Beniamino Galvani <b.galvani@gmail.com>
The LBMAP switches on the board will tell which boot device is used.
Only QSPI boot is supported if the boot device is IFCCard.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This reverts commit 1a5f0de08e86("sunxi: make SoC variant choice
mandatory").
With the optional marking in the Kconfig "make savedefconfig"
will drop CONFIG_MACH_SUN4I=y from all the A10 boards, making it
hard to see at a glance which family of sunxi chips the defconfig
is for.
This commit therefore restores the optional, and restores
CONFIG_MACH_SUN4I=y to all defconfig's which had it dropped
because of this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The inet86dz board is a board used in 7" tablets from various oems.
These tablets are a23 based 7" tablets featuring a 1024x600 LCD,
512MB RAM, 4G NAND, rtl8188etv usb wifi, gsl1680 touchschreen,
micro-sd slot, 3.5mm headphone jack and a micro-usb otg connector
which doubles as charging port.
The dts file this commit adds is identical to the one submitted to
the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The Polaroid MID2407PXE03 is an a23 based 7" tablet based on a M86_MB V2.0
PCB, featuring a 800x480 LCD, 512MB RAM, 4G NAND, esp8089 wifi, gsl1680
touchschreen, micro-sd slot, 3.5mm headphone jack and a micro-usb otg
connector which doubles as charging port.
The dts file is identical to the one submitted to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The following changes are made to the clock API:
* The concept of "clocks" and "peripheral clocks" are unified; each clock
provider now implements a single set of clocks. This provides a simpler
conceptual interface to clients, and better aligns with device tree
clock bindings.
* Clocks are now identified with a single "struct clk", rather than
requiring clients to store the clock provider device and clock identity
values separately. For simple clock consumers, this isolates clients
from internal details of the clock API.
* clk.h is split so it only contains the client/consumer API, whereas
clk-uclass.h contains the provider API. This aligns with the recently
added reset and mailbox APIs.
* clk_ops .of_xlate(), .request(), and .free() are added so providers
can customize these operations if needed. This also aligns with the
recently added reset and mailbox APIs.
* clk_disable() is added.
* All users of the current clock APIs are updated.
* Sandbox clock tests are updated to exercise clock lookup via DT, and
clock enable/disable.
* rkclk_get_clk() is removed and replaced with standard APIs.
Buildman shows no clock-related errors for any board for which buildman
can download a toolchain.
test/py passes for sandbox (which invokes the dm clk test amongst
others).
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add a README file for helping users to install U-Boot into the eMMC.
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Acked-by: Fabio Estevam <fabio.estevam@nxp.com>
The latest version of warp7 board provides the connection of the
WDOG1_B pin to the PMIC.
Program the watchdog to enable the WDOG1_B output which causes
a POR reset.
Based on the imx7dsabresd code.
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Acked-by: Fabio Estevam <fabio.estevam@nxp.com>
The current pad DSE for QSPI is 60ohm. This setting cause
too strong drive to clock and data signals. Need to change
the DSE to 120ohm for better signal quality.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Q901 is PMOS, LCD_nPWREN should be at low voltage then output is 3V3.
If LCD_nPWREN is high, output is 2.4V which is not correct.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Fix 74LV OE gpio index. gpio index is wrong,
so gpio output will not have effect, since we
use wrong GPIO5_IO18, but not correct GPIO5_IO8.
And at the end of the initialization of 74lv init, should
keep OE voltage level at LOW to make 74lv output the correct
voltage.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
LCD_PWR_EN controls the G pin of Q13 PMOS which needs low voltage to connect
D to S for outputting LCD 3.3V. If LCD_PWR_EN is high, we measured the LCD 3v3
is actually 1.2V.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Currently the LVDS backlight does not work in U-Boot after a “reboot” comand
in the kernel.
This problem occurs because the kernel uses this pin in PWM mode and U-Boot
does not configure the backlight pin as GPIO functionality.
So fix the problem by explicitly configuring the backlight pin as GPIO in
U-Boot.
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
This patch is doing the following:
1. Implementing the errata for LS2080.
2. Adding fixup for fdt for LS2080.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
FIT allows for a multiple dtb in a single image. SPL needs away to
detect the right dtb to be used. Adding support for the same for am57xx
platforms.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
board/am57xx supports all boards based on am57xx. Rename the taget
as TARGET_AM57XX_EVM.
Fixes: 74cc8b097d ("board: ti: beagle_x15: Rename to indicate support for TI am57xx evms")
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add initial support for NXP's S32V234 SoC and S32V234EVB board.
The S32V230 family is designed to support computation-intensive applications
for image processing. The S32V234, as part of the S32V230 family, is a
high-performance automotive processor designed to support safe
computation-intensive applications in the area of vision and sensor fusion.
Code originally writen by:
Original-signed-off-by: Stoica Cosmin-Stefan <cosminstefan.stoica@freescale.com>
Original-signed-off-by: Mihaela Martinas <Mihaela.Martinas@freescale.com>
Original-signed-off-by: Eddy Petrișor <eddy.petrisor@gmail.com>
Signed-off-by: Eddy Petrișor <eddy.petrisor@nxp.com>
Now when we have support of IOC (IO-Coherency block) cahce operations
on regions are tuned to not be dummy stubs if IOC was found and enabled
in the core. That makes flush_dcache_range() useless for our purposes
here. And since we do need to flush modified reset vector to at least L2
cache (AKA SLC) so other cores will see it via its L1 instruction cache
we're using always functional flush_dcache_all() here.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Marek Vasut <marex@denx.de>
This board is based on Snapper 9G45 which has an Atmel AT91SAM9G45 chip and
128MB of SDRAM. It includes a small LCD, 2xUSB host, SD card, Ethernet and
two UARTs.
Signed-off-by: Andre Renaud <andre@designa-electronics.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
[apply CONFIG_BOOTDELAY transition]
Signed-off-by: Andreas Bießmann <andreas@biessmann.org>
Currently omap_vcores which holds pmic data is being assigned based
on the SoC type. PMIC is not a part of SoC. It is logical to
to assign omap_vcores based on board type. Hence over ride the
vcores_init function and assign omap_vcores based on the board type.
Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
This patch adds QSPI boot support for LS2080AQDS board.
The QSPI boot image need to be programmed into the QSPI flash
first. Then we can switch to booting from QSPI memory space.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
When QSPI is enabled, NOR flash and QIXIS can't be accessed
through IFC due to pin mux. Enable I2C QIXIS access and I2C
early init to read the sysclk and ddrclk.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Environment variable mcinitcmd is defined to initiate MC and DPL
deployment from the location where it is stored (NOR, NAND, SD, SATA,
USB) during booting. If this variable is not defined then macro
MC_BOOT_ENV_VAR will be null and MC will not be booted and DPL will
not be applied during U-boot booting.
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
In the draco CPU board family, etamin is a new variant
with bigger flash and more RAM. Due to new flash that
uses larger pages (4K) some changes are necessary because
it impacts the MTD partition layout and the ubi mount
parameters.
Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
[trini: Move BOOTDELAY into defconfig, just always be 3 now]
Signed-off-by: Tom Rini <trini@konsulko.com>
read the ECC Type field from the i2c eeprom, instead
configuring it static in the U-Boot binary.
see RM:
Table 26-17. NAND Geometry Information on I2C EEPROM
Signed-off-by: Heiko Schocher <hs@denx.de>
This adds support for IS1 board. Pretty usual socfpga board,
256MB of RAM, does not have MMC, two SPI chips, one ethernet port, two
additional ethernet ports connected to the FPGA.
Signed-off-by: Pavel Machek <pavel@denx.de>
Use a single defconfig for all DRA7xx hs platforms by enabling FIT and delete
the platform specific defconfigs.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
There is a new strider console flavor with DisplayPort
video.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Reviewed-by: Tom Rini <trini@konsulko.com>
