This uclass is intended to provide a way to obtain information about a
U-Boot board. But the concept of a U-Boot 'board' is the whole system,
not just one circuit board, meaning that 'board' is something of a
misnomer for this uclass.
In addition, the name 'board' is a bit overused in U-Boot and we want to
use the same uclass to provide SMBIOS information.
The obvious name is 'system' but that is so vague as to be meaningless.
Use 'sysinfo' instead, since this uclass is aimed at providing information
on the system.
Rename everything accordingly.
Note: Due to the patch delta caused by the symbol renames, this patch
shows some renamed files as being deleted in one place and created in
another.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a script to boot Chrome OS from the internal MMC. This involved adding
a few commands and options.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present CONFIG_CHROMEOS is used to determine whether verified boot is
in use. The code to implement that is not in U-Boot mainline.
However, it is useful to be able to boot a Chromebook in developer mode
in U-Boot mainline without needing the verified boot code.
To allow this, use CONFIG_CHROMEOS_VBOOT to indicate that verified boot
should be used, and CONFIG_CHROMEOS to indicate that the board supports
Chrome OS. That allows us to define CONFIG_CHROMEOS on coral.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
If u-boot gets used as coreboot payload it might be nice to get
vendor, model and bios version from smbios. I am not sure about
the output of all the read information.
With qemu target for coreboot this could look this:
CBFS: Found @ offset 14f40 size 3b188
Checking segment from ROM address 0xffc15178
Checking segment from ROM address 0xffc15194
Loading segment from ROM address 0xffc15178
code (compression=1)
New segment dstaddr 0x01110000 memsize 0x889ef srcaddr 0xffc151b0 filesize 0x3b150
Loading Segment: addr: 0x01110000 memsz: 0x00000000000889ef filesz: 0x000000000003b150
using LZMA
Loading segment from ROM address 0xffc15194
Entry Point 0x01110000
BS: BS_PAYLOAD_LOAD run times (exec / console): 77 / 1 ms
Jumping to boot code at 0x01110000(0x07fa7000)
U-Boot 2020.10-00536-g5dcf7cc590-dirty (Oct 07 2020 - 14:21:51 +0200)
CPU: x86_64, vendor AMD, device 663h
DRAM: 127.1 MiB
MMC:
Video: No video mode configured in coreboot!
Video: No video mode configured in coreboot!
Vendor: QEMU
Model: Standard PC (i440FX + PIIX, 1996)
Bios Version: 4.12-3152-g326a499f6f-dirty
Net: e1000: 52:54:00:12:34:56
eth0: e1000#0
No working controllers found
Finalizing coreboot
Hit any key to stop autoboot: 0
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
GE B1x5v2 patient monitor series is similar to the CARESCAPE Monitor
series (GE Bx50). It consists of a carrier PCB used in combination
with a Congatec QMX6 SoM. This adds U-Boot support using device model
everywhere and SPL for memory initialization.
Proper configuration is provided as 'ge_b1x5v2_defconfig' and the
combined image u-boot-with-spi.imx can be flashed directly to 1024
byte offset to /dev/mtdblock0. Alternatively SPL and u-boot.imx can
be loaded separately via USB-OTG using e.g. imx_usb.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
- New PX30 board: Engicam PX30.Core;
- Fix USB HID support for rock960;
- Remove host endianness dependency for rockchip mkimage;
- dts update for rk3288-tinker;
- Enable console MUX for some ROCKPi boards;
- Add config-based ddr selection for px30;
PX30.Core is an EDIMM SOM based on Rockchip PX30 from Engicam.
C.TOUCH 2.0 is a general purpose carrier board with capacitive
touch interface support.
PX30.Core needs to mount on top of this Carrier board for creating
complete PX30.Core C.TOUCH 2.0 board.
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
PX30.Core is an EDIMM SOM based on Rockchip PX30 from Engicam.
EDIMM2.2 Starter Kit is an EDIMM 2.2 Form Factor Capacitive
Evaluation Board from Engicam.
PX30.Core needs to mount on top of this Evaluation board for
creating complete PX30.Core EDIMM2.2 Starter Kit.
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
Enable Console multiplexing in ROCKPi N8 which would is
required to video out the console buffer.
Enable it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
Enable Console multiplexing in ROCKPi N10 which would is
required to video out the console buffer.
Enable it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
On aristianetos boards the display type is detected
through "panel" environment variable. Dependend on the
display type we detect the board type and this decides which
DTB we have to use for the board.
So we need early spi environment access.
Signed-off-by: Heiko Schocher <hs@denx.de>
Fix up USB config options so keyboards and other USB devices work.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
Change-Id: I34b0696e0ac7303186f20c83278dde340399b690
Add a simple test that we can obtain the correct parent for an I2C
device. This requires updating the driver names to match the compatible
strings, adding them to the devicetree and enabling a few options.
Signed-off-by: Simon Glass <sjg@chromium.org>
We have a test in dtoc for this feature, but not one in U-Boot itself.
Add a simple test that checks that the information comes through
correctly.
Signed-off-by: Simon Glass <sjg@chromium.org>
- Armada 8k: Add NAND support via PXA3xx NAND driver (Baruch)
- Armada 8k: Use ATF serdes init instead of the "old" U-Boot version
(Baruch)
- Minor update to Octeon TX/TX2 defconfig (Stefan)
common:
- Add support for 64bit loadables from SPL
xilinx:
- Update documentation and record ownership
- Enable eeprom board detection based legacy and fru formats
- Add support for FRU format
microblaze:
- Optimize low level ASM code
- Enable SPI/I2C
- Enable distro boot
zynq:
- Add support for Zturn V5
zynqmp:
- Improve silicon detection code
- Enable several kconfig options
- Align DT with the latest state
- Enabling security commands
- Enable and support FPGA loading from SPL
- Optimize xilinx_pm_request() calling
versal:
- Some DTs/Kconfig/defconfig alignments
- Add binding header for clock and power
zynq-sdhci:
- Add support for tap delay programming
zynq-spi/zynq-qspi:
- Use clock framework for getting clocks
xilinx-spi:
- Fix some code issues (unused variables)
serial:
- Check return value from clock functions in pl01x
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCX5rH/QAKCRDKSWXLKUoM
IRPAAJ9SvHR3w1qTc5W+Q5CWBUH5wJbNYQCaA4PpqZCdvyu1+nF5luL6JHhbDgw=
=hOd7
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2021.01-v2' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2021.01-v2
common:
- Add support for 64bit loadables from SPL
xilinx:
- Update documentation and record ownership
- Enable eeprom board detection based legacy and fru formats
- Add support for FRU format
microblaze:
- Optimize low level ASM code
- Enable SPI/I2C
- Enable distro boot
zynq:
- Add support for Zturn V5
zynqmp:
- Improve silicon detection code
- Enable several kconfig options
- Align DT with the latest state
- Enabling security commands
- Enable and support FPGA loading from SPL
- Optimize xilinx_pm_request() calling
versal:
- Some DTs/Kconfig/defconfig alignments
- Add binding header for clock and power
zynq-sdhci:
- Add support for tap delay programming
zynq-spi/zynq-qspi:
- Use clock framework for getting clocks
xilinx-spi:
- Fix some code issues (unused variables)
serial:
- Check return value from clock functions in pl01x
Enable the now included network drivers in the currently supported
Marvell Octeon TX & TX2 boards.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Suneel Garapati <sgarapati@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Tests tests run the three mux subcommands: list, select, and deselect,
and verify that the commands do what we expect.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Provide tests to check the behavior of the multiplexer framework.
Two sets of tests are added. One is using an emulated multiplexer driver
that can be used to test basic functionality like select, deselect, etc.
The other is using the mmio mux which adds tests specific to it.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With disabled legacy VIDEO option CONSOLE_MUX is not auto-selected
any more, re-enable it.
Fixes: 9dec5a0ea1 ("nokia_rx51: disable obsolete VIDEO config")
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Pali Rohár <pali@kernel.org>
There is no reason to have ZYNQ specific Kconfig macro in generic location
to be visible for all other SoCs. That's why move it to Xilinx common
location to be visible only for us.
Also introduce new bool entry ZYNQ_MAC_IN_EEPROM to have also an option to
disable it or enable. This has connection to code which is reading the
whole content of i2c and also work with the rest of date not just with MAC
address.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
SPL DT contains only nodes which are contain u-boot,dm-pre-reloc property.
iommu node is not this case that's why when DT is read DTC reports some
warnings.
$ dtc -I dtb -O dts dts/dt-spl.dtb >/dev/null
<stdout>: Warning (iommus_property): /amba/spi@ff0f0000:iommus: Could not get phandle node for (cell 0)
<stdout>: Warning (iommus_property): /amba/mmc@ff160000:iommus: Could not get phandle node for (cell 0)
<stdout>: Warning (iommus_property): /amba/mmc@ff170000:iommus: Could not get phandle node for (cell 0)
SPL also has an option to remove some DT properties which are useless for
SPL to make DT even smaller.
Default DT properties are pinctrl-0 pinctrl-names interrupt-parent
interrupts which are already removed.
The patch extends this list with iommus to get rid of above warnings.
Also power-domains unused properties can be removed.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Sometimes it is very useful to be able disable/enable cache that's why
enable commands for it by default.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
fpga bitstream needs to be listed in config node in FIT image. Only tested
option is bitstream in BIN format.
Enabling this feature increase code size by almost 4k.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Mini u-boot timer clock is not updated when u-boot is migrated from
emulator to silicon. Due to this slower clock of 2.72Mhz, delay() functions
are not working accurately. Update CONFIG_COUNTER_FREQUENCY to 100Mhz.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add distro boot support for microblaze and enable jtag, qspi,
dhcp, pxe boot targets for distro boot.
Enable DISTRO_DEFAULTS config in microblaze defconfig and also
enable support for spi xilinx driver & spi vendors to access
spi flash by distro boot.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Adding Z-turn board V5 to resolve the change between:
"Z-TURNBOARD_schematic.pdf" schematics state version 1 to 4 has Atheros AR8035
"Z-Turn_Board_sch_V15_20160303.pdf" schematics state version 5 has Micrel KSZ9031
At this time the S25FL128SAGNFI003 doesn't work because of bug:
*** Warning - spi_flash_probe_bus_cs() failed, using default environment
zynq-zturn was checked on V5 board, same error.
Maybe Z-turn board have the same problem (board with W25Q128BVFIG).
Signed-off-by: Alexandre GRIVEAUX <agriveaux@deutnet.info>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
DM_VIDEO conversion deadline has passed, disable VIDEO config.
Boards should convert to DM_VIDEO if they need video console
support.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
DM_VIDEO conversion deadline has passed, disable VIDEO config.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Erik van Luijk <evanluijk@interact.nl>
The "cmd/Kconfig" has a TODO description for CMD_MISC that it should
really be named as CMD_SLEEP. Change it in the whole source tree.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Enable the CMD_MDIO Kconfig option by removing the "is not set"
indication from all the defconfigs for this SoC.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add basic support for the Kontron SMARC-sAL28 board. This includes just
the bare minimum to be able to bring up the board and boot linux.
For now, the Single and Dual PHY variant is supported. Other variants
will fall back to the basic variant.
In particular, there is no watchdog support for now. This means that you
have to disable the default watchdog, otherwise you'll end up in the
recovery bootloader. See the board README for details.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Enable support to compile OPTEE driver, access AVB TA
and RPMB API's access via RPC from OPTEE for lx2160
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
CONFIG_{SPL,TPL}_SIZE_LIMIT are defined as hex (SPL_SIZE_LIMIT was
converted in b51882d0 ("spl: Convert CONFIG_SPL_SIZE_LIMIT to hex"), but
there are still places that reference integer values. Change those to hex
as well. Also, update the Makefile to check for 0x0 instead of 0.
This also fixes the following build error when CONFIG_SPL_SIZE_LIMIT
is set by menuconfig to 0x0:
...
spl/u-boot-spl.bin exceeds file size limit:
limit: 0 bytes
actual: 0x80f0 bytes
excess: 0x80f0 bytes
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- Fix stm32prog command: parsing of FlashLayout without partition
- Update MAINTAINERS for ARM STM STM32MP
- Manage eth1addr on dh board with KS8851
- Limit size of cacheable DDR in pre-reloc stage in stm32mp1
- Use mmc_of_parse() to read host capabilities in mmc:sdmmc2 driver
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl+QXvgACgkQ4rK92eCq
k3Vbrgf/cBKPY9bS+lJVARgjDvIOdcXzpgH/F7dUlq+dzu/mCwhIBVKxM7/nXh5p
RhfGET2fpMYY/41LkKza7AqOiGTXZG4pTmCGe1UHXrXeIPjinWG1LQjU/KOk6U4n
681P9BZfTUXrVgzLBIUY1KBFVyMaiYfVjxU3MnA1vqrubymFbf+IpUt3OIegUDCp
AjrTdj7sFEQ3nG/pgTyqFCwkl/MG53aB9MiaBBRxeGHYnDn0qzAEHSGqzSZZGhNl
1ubJDF3K7w6Pj3MzIeA80M5r0fJoTy/qWcNH31psOpyQaHJ9NbPGjFYE6AkDPV4l
27QN71AcRtCzlv1XQpblA98pa1bUYw==
=Bl3G
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20201021' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- Activate CMD_EXPORTENV/CMD_IMPORTENV/CMD_ELF for STM32MP15 defconfig
- Fix stm32prog command: parsing of FlashLayout without partition
- Update MAINTAINERS for ARM STM STM32MP
- Manage eth1addr on dh board with KS8851
- Limit size of cacheable DDR in pre-reloc stage in stm32mp1
- Use mmc_of_parse() to read host capabilities in mmc:sdmmc2 driver
A64-Teres-I board is a laptop which comes with a builtin keyboard.
The keyboard+trackpad controller pauses for 2 seconds at a firmware
prompt before loading its HID interface.
U-Boot needs to wait equally long to reliably enable the keyboard.
Signed-off-by: Jonas Smedegaard <dr@jones.dk>
Reviewed-by: Tom Rini <trini@konsulko.com>
Series-Cc: Jagan Teki <jagan@amarulasolutions.com>
Series-Cc: Lukasz Majewski <lukma@denx.de>
Series-Cc: Andre Przywara <andre.przywara@arm.com>
Olimex OLinuXino LIME2 rev. H through L uses Micrel KSZ9031 PHY.
This enables the Micrel PHY for A20-OLinuXino-Lime2-eMMC_defconfig.
Signed-off-by: Jonas Smedegaard <dr@jones.dk>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
According to the devicetree and the schematic, the 3.3V power rail for
the PHY is enabled by GPIO PC16. It's wired as active-high, with a
pull-up resistor, so actually works already when the GPIO is in
High-Z state.
However we should not take any chances and explicitly set the GPIO pin
to high, to avoid accidentally losing the PHY power.
The existing MACPWR Kconfig allows to do this easily.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Activate CONFIG_CMD_ELF to accept the command "bootelf".
This patch simplifies the file stm32mp defconfig, as we have
no reason to deactivate this command.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Activate CONFIG_CMD_IMPORTENV to accept the command "env import".
This command is useful in script to include some variable.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Enable mtu3, xhci, tphy drivers.
Device mode: enable fastboot;
Host mode: enable USB, FAT commands, and fixed regulator,
mass storage drivers;
Due to device mode is enabled by default, comment out
the host mode config here.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAl+NMmQcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyLnEB/0cWFfjDfCMY1o7R4QX
DeDRlD6k6acQWlwa5EiRKwpbPMJKrSI/m5alMCYZG6YHvGtzihqnqohz3gl1sepi
W7eyyyFsM4hqe4P3lSETJRGWe/O8bNkoa0hBzqZ9btqw2OJLBu4JYB+zKgz8kaDY
jzkGLgaaK6wtG3rEu+q4fjzp1y9kuz31WnN+9qS8jd/9UH13XKCkJl9TfY5pLfgc
mmbn2NWtAhi91uShcnIsOpLaNm23IV0ITa22etB9F1docZuUrbhOtiIF45AADjpG
/xtkV3dEVGml3N/17RizgOwxX3xughG0ak9xifsK6tfgqfVhaGMgkToNNBM+1ddm
rZZM
=hF12
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2021.01-b' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
Second set of u-boot-atmel features for 2021.01 cycle:
This feature set brings the rework of the clock tree for sam9x60 SoC.
This makes the clock tree fully compatible with Common Clock Framework
and allows full clock configuration in U-Boot. This means that the
sam9x60 boards can boot now using U-Boot.
This also includes the definitions for sam9x60 SiPs and a divisor fix
for the clock on sama7g5 SoC.
Done with:
./tools/moveconfig.py VIDEO_BMP_GZIP
The 3 suspicious migration because CMD_BMP and SPLASH_SCREEN
are not activated in these defconfigs:
- trats_defconfig
- s5pc210_universal_defconfig
- trats2_defconfig
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- fsl_esdhc_imx cleanup
- not send cm13 if send_status is 0.
- Add reinit API
- Add mmc HS400 for fsl_esdhc
- Several cleanup for fsl_esdhc
- Add ADMA2 for sdhci
- Octeon TX: Add NAND driver (Suneel)
- Octeon TX: Add NIC driver driver (Suneel)
- Octeon TX2: Add NIC driver driver (Suneel)
- Armada 8040: Add iEi Puzzle-M80 board support (Luka)
- Armada A37xx SPI: Add support for CS-GPIO (George)
- Espressobin: Use Linux model/compatible strings (Andre)
- Espressobin: Add armada-3720-espressobin-emmc.dts from Linux (Andre)
- Armada A37xx: Small cleanup of config header (Pali)
Add PStore command to sandbox and sandbox64 defconfigs.
Add test checking:
- 'pstore display' of all records
- 'pstore display' only the 2nd dump record
- 'pstore save' of all records
Signed-off-by: Frédéric Danis <frederic.danis@collabora.com>
[trini: Adjust to always load files from source directory]
Signed-off-by: Tom Rini <trini@konsulko.com>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Add initial U-Boot support for the iEi Puzzle-M801 board based on the
Marvell Armada 88F8040 SoC.
Currently supported hardware:
1x USB 3.0
4x Gigabit Ethernet
2x SFP+ (with NXP PCA9555 and NXP PCA9544)
1x SATA 3.0
1x M.2 type B
1x RJ45 UART
1x SPI flash
1x EPSON RX8010 RTC
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
- Minor cleanup on K3 env variables
- Fix OSPI compatible for J721e
- Drop unused property in omap-usb2-phy
- Update Maintainer for am335x-guardian board.
CONFIG_OF_EMBED was primarily enabled to support the S10/Agilex
spl hex file requirements. Since this option now produces a
warning during build, and the spl hex can be created using
alternate methods, CONFIG_OF_EMBED is no longer needed.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Don't invoke 'SYSTEM_RESET' PSCI function because PSCI
function calls are not supported by u-boot running in EL3.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
All SoCFPGA platforms (except Cyclone V) are now switching
to CONFIG_WDT (driver model for watchdog timer drivers)
from CONFIG_HW_WATCHDOG.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
In current implementation, any exception would trigger a CPU reset.
But a bad written SPL would cause infinite loop where the system
will reload the same SPL instead of loading factory safe image.
Hence this patch is to ensure any exception will cause a hang. At this
moment, watchdog shall be triggered and Remote System Update mechanism
shall load the next production image or factory safe image.
Signed-off-by: Chin Liang See <chin.liang.see@intel.com>
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Now that PIE works when U-Boot is started from ROM, let's enable
CONFIG_POSITION_INDEPENDENT, which allows to load U-Boot also via
ARM Trusted-Firmware's fip.bin to DRAM, without tweaking the
configuration.
To get a writable initial stack, we need to keep the fixed initial
stack pointer, which points to DRAM in our case.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
This patch adds the board specific configuration (struct) for the
Octeon 3 EBB7304 EVK. This struct is ported from the 2013er Cavium /
Marvell U-Boot repository. Also, the Octeon RAM driver is enabled in
the board defconfig for its usage.
Tested with one and two DIMMs on the EBB7304 EVK (8 & 16 GiB).
Signed-off-by: Stefan Roese <sr@denx.de>
The following bugs in the UEFI system are resolved:
* illegal free in EFI_LOAD_FILE2_PROTOCOL implementation
* incorrect documentation of EFI_LOAD_FILE2_PROTOCOL implementation
* output of CRC32 as decimal instead hexadecimal in unit test
* use EfiReservedMemoryType for no-map reserved memory
* avoid unnecessary resets in UEFI unit tests
* call EFI bootmgr even without having /EFI/boot
-----BEGIN PGP SIGNATURE-----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=laLr
-----END PGP SIGNATURE-----
Merge tag 'efi-2021-01-rc1' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2021-01-rc1
The following bugs in the UEFI system are resolved:
* illegal free in EFI_LOAD_FILE2_PROTOCOL implementation
* incorrect documentation of EFI_LOAD_FILE2_PROTOCOL implementation
* output of CRC32 as decimal instead hexadecimal in unit test
* use EfiReservedMemoryType for no-map reserved memory
* avoid unnecessary resets in UEFI unit tests
* call EFI bootmgr even without having /EFI/boot
- Add USB support for GXL and AXG SoCs
- Update Gadget code to use the new GXL and AXG USB glue driver
- Add a VIM3 board support to add dynamic PCIe enable in OS DT
- Fix AXG pinmux with requesting GPIOs
- Add missing GPIOA_18 for AXG pinctrl
- Add Amlogic PWM driver
-----BEGIN PGP SIGNATURE-----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=rbAX
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20201005' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic
- generate unique mac address from SoC serial on S400 board
- Add USB support for GXL and AXG SoCs
- Update Gadget code to use the new GXL and AXG USB glue driver
- Add a VIM3 board support to add dynamic PCIe enable in OS DT
- Fix AXG pinmux with requesting GPIOs
- Add missing GPIOA_18 for AXG pinctrl
- Add Amlogic PWM driver
CONFIG_EFI_GRUB_ARM32 is only needed for architectures with caches that are
not managed via CP15 (or for some outdated buggy versions of GRUB). It
makes more sense to disable the setting per architecture than per defconfig.
Move QEMU's CONFIG_EFI_GRUB_ARM32_WORKAROUND=n from defconfig to Kconfig.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The VIM3 on-board MCU can mux the PCIe/USB3.0 shared differential
lines using a FUSB340TMX USB 3.1 SuperSpeed Data Switch between
an USB3.0 Type A connector and a M.2 Key M slot.
The PHY driving these differential lines is shared between
the USB3.0 controller and the PCIe Controller, thus only
a single controller can use it.
This adds this dynamic switching right before booting Linux
and the configuration steps in the boards documentation.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
[narmstrong: fixed warning by replacing min() by min_t()]
Use the newly added VIM3 board support instead of the generic W400.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This commit enable the support of the generic udp protocol.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add tests for SCMI reset controllers. A test device driver
sandbox-scmi_devices.c is used to get reset resources, allowing further
resets manipulation.
Change sandbox-smci_agent to emulate 1 reset controller exposed through
an agent. Add DM test scmi_resets to test this reset controller.
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add tests for SCMI clocks. A test device driver sandbox-scmi_devices.c
is used to get clock resources, allowing further clock manipulation.
Change sandbox-smci_agent to emulate 3 clocks exposed through 2 agents.
Add DM test scmi_clocks to test these 3 clocks.
Update DM test sandbox_scmi_agent with load/remove test sequences
factorized by {load|remove}_sandbox_scmi_test_devices() helper functions.
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This change introduces SCMI agent uclass to interact with a firmware
using the SCMI protocols [1].
SCMI agent uclass currently supports a single method to request
processing of the SCMI message by an identified server. A SCMI message
is made of a byte payload associated to a protocol ID and a message ID,
all defined by the SCMI specification [1]. On return from process_msg()
method, the caller gets the service response.
SCMI agent uclass defines a post bind generic sequence for all devices.
The sequence binds all the SCMI protocols listed in the FDT for that
SCMI agent device. Currently none, but later change will introduce
protocols.
This change implements a simple sandbox device for the SCMI agent uclass.
The sandbox nicely answers SCMI_NOT_SUPPORTED to SCMI messages.
To prepare for further test support, the sandbox exposes a architecture
function for test application to read the sandbox emulated devices state.
Currently supports 2 SCMI agents, identified by an ID in the FDT device
name. The simplistic DM test does nothing yet.
SCMI agent uclass is designed for platforms that embed a SCMI server in
a firmware hosted somewhere, for example in a companion co-processor or
in the secure world of the executing processor. SCMI protocols allow an
SCMI agent to discover and access external resources as clock, reset
controllers and more. SCMI agent and server communicate following the
SCMI specification [1]. This SCMI agent implementation complies with
the DT bindings defined in the Linux kernel source tree regarding
SCMI agent description since v5.8.
Links: [1] https://developer.arm.com/architectures/system-architectures/software-standards/scmi
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Remove empty board_early_init_f function, since it is disabled
in ebisu and condor board configs.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Use "imply" instead of "select" for BOARD_EARLY_INIT_F config option,
and then disable it on boards which don't need it.
Updated grpeach_defconfig to disable CONFIG_BOARD_EARLY_INIT_F option for
RZA1.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Enable the fitImage update options on RCar Gen3 boards.
This permits easy update of multiple bootloader components.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Enable the RPC Hyperflash driver on R8A7795,R8A7796,R8A77965
Salvator-X,ULCB and R8A77990 Ebisu. Note that to make the HF
accessible, mainline ATF is mandatory and must be built with
RCAR_RPC_HYPERFLASH_LOCKED=0 . Note that this is intended for
development and testing convenience only and must be disabled
in deployment for platform security reasons.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
- Enhance the 'zboot' command to be more like 'bootm' with sub-commands
- The last series of ACPI core changes for programmatic generation of
ACPI tables
- Add all required ACPI tables for ApolloLake and enable ACPIGEN on
Chromebook Coral
- A feature minor enhancements to the 'hob' command
- Intel edison: Support for writing an xFSTK image via binman
Enable new features and provide require device-tree config so that U-Boot
produces the correct ACPI tables on Coral.
Signed-off-by: Simon Glass <sjg@chromium.org>
Intel WiFi chips can use a common routine to write the information needed
by linux. Add an implementation of this.
Enable it for coral.
Signed-off-by: Simon Glass <sjg@chromium.org>
The extra ACPI code increases U-Boot above it current size limit. Move
the start earlier to provide space.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
arm64:
- Support for bigger U-Boot images compiled with PIE
microblaze:
- Extend support for LE/BE systems
zynqmp:
- Refactor silicon ID detection code with using firmware interface
- Add support for saving variables based on bootmode
zynqmp-r5:
- Fix MPU mapping and defconfig setting.
xilinx:
- Minor driver changes: names alignment
- Enable UBIFS
- Minor DT and macros fixes
- Fix boot with appended DT
- Fix distro boot
cmd:
- pxe: Add fixing for platforms with manual relocation support
clk:
- fixed_rate: Add DM flag to support early boot on r5
fpga:
- zynqmppl: Use only firmware interface and enable SPL build
serial:
- uartlite: Enable for ARM systems and support endians
mmc:
- zynq: Fix indentation
net:
- gem: Support for multiple phys
- emac: Fix 64bit support and enable it for arm64
kconfig:
- Setup default values for Xilinx platforms
- Fix dependecies for Xilinx drivers
- Source board Kconfig only when platform is enabled
- Fix FPGA Kconfig entry with SPL
- Change some defconfig values
bindings:
- Add binding doc for vsc8531
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCX2x4MgAKCRDKSWXLKUoM
IZQtAJ9HpNwG5q3nHt9WedzLCTkr3YoLAACeJJ0Wlpp5p5xPzuPmnoo/Vi4MtNQ=
=yxRo
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2021.01' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2021.01
arm64:
- Support for bigger U-Boot images compiled with PIE
microblaze:
- Extend support for LE/BE systems
zynqmp:
- Refactor silicon ID detection code with using firmware interface
- Add support for saving variables based on bootmode
zynqmp-r5:
- Fix MPU mapping and defconfig setting.
xilinx:
- Minor driver changes: names alignment
- Enable UBIFS
- Minor DT and macros fixes
- Fix boot with appended DT
- Fix distro boot
cmd:
- pxe: Add fixing for platforms with manual relocation support
clk:
- fixed_rate: Add DM flag to support early boot on r5
fpga:
- zynqmppl: Use only firmware interface and enable SPL build
serial:
- uartlite: Enable for ARM systems and support endians
mmc:
- zynq: Fix indentation
net:
- gem: Support for multiple phys
- emac: Fix 64bit support and enable it for arm64
kconfig:
- Setup default values for Xilinx platforms
- Fix dependecies for Xilinx drivers
- Source board Kconfig only when platform is enabled
- Fix FPGA Kconfig entry with SPL
- Change some defconfig values
bindings:
- Add binding doc for vsc8531
commit 0cfccb5401 ("configs: Resync with savedefconfig")
removed CONFIG_USB_STORAGE from some powerpc platforms' defconfig
files, whicih would block the use case of system loading rootfs
from USB drives, add them back.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Enable the DM_ETH and DM_MDIO config.
On P2020RDB, the eTSEC1 is connecting with a switch VSC7385,
so also enable the fixed PHY support.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Enable the DM_ETH and DM_MDIO config.
On P1020RDB, the eTSEC1 is connecting with a switch VSC7385,
so also enable the fixed PHY support.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The tsec driver now requires DM_MDIO when DM_ETH is enabled. To avoid
build errors, enable DM_MDIO in these boards' configs before we actually
add DM_MDIO support to tsec.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This patch is to enable espi DM for T2080QDS in uboot
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Testing on a DNS-325 NAS has shown that in order for the device to work
we need to set CONFIG_NR_DRAM_BANKS to 1 and not 2.
Tested-by: Dmitry N. Kolesnikov <dk.diklab@gmail.com>
Reported-by: Dmitry N. Kolesnikov <dk.diklab@gmail.com>
Cc: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
Signed-off-by: Tom Rini <trini@konsulko.com>
Required for the generic distro mechanism.
Linux ships with 4 variants:
marvell/armada-3720-espressobin-v7-emmc.dtb
marvell/armada-3720-espressobin-v7.dtb
marvell/armada-3720-espressobin-emmc.dtb
marvell/armada-3720-espressobin.dtb
Use available information to determine the appropriate filename.
Fixes booting GRUB EFI arm64 on Fedora.
Reported-by: Dennis Gilmore <dennis@ausil.us>
Signed-off-by: Andre Heider <a.heider@gmail.com>
The hardware does not provide a MAC address. Enable this so that
network access works with just the default environment.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Acked-by: Konstantin Porotchkin <kostap@marvell.com>
CONFIG_ENV_OVERWRITE disables write protection on various environment
variables like "ethaddr" and "serial".
Enable this config in LS1046A and LS1012A defconfigs. This resolves an
error while setting multiple values of "ethaddr" variable.
Before the change:
=> setenv ethaddr 00:E0:0C:00:06:0
=> setenv ethaddr 00:E0:0C:00:06:1
Error: Can't overwrite "ethaddr"
Error inserting "ethaddr" variable, errno=1
After the change:
=> setenv ethaddr 00:E0:0C:00:06:0
=> setenv ethaddr 00:E0:0C:00:06:1
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Both SOCs shouldn't have any problem with 64bit dma accesses. Also with PIE
enabled when u-boot is placed above 4GB without any memory mapped below 4GB
address space efi_memory_init() call is failing due to missing memory node.
For this two reason disable this option for ZynqMP and Versal.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The patch does sed 's/SPL_FPGA_SUPPORT/SPL_FPGA/g' but also fixing Makefile
and zynqmp.c to simplify if/endif logic in zynqmp.c.
This change is mostly done to be able to use CONFIG_IS_ENABLED macro and
obj-$(CONFIG_$(SPL_)FPGA) in Makefile. For them symbols need to be in sync.
And removing one line from Topic Miami boards which is not needed because
symbol is not enabled via Kconfig.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Enable position independent pre-relocation to let users options to put
u-boot to different locations.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enabling saving variables to MMC(FAT), NAND, SPI based on primary bootmode.
Maybe that logic can be tuned for more complicated use cases and better
tested for different bootmodes.
Tested on zcu104 to SD(FAT) and JTAG(NOWHERE).
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
NAND_ARASAN selecting DM_MTD uunconditionally. Driver can be enabled with
!DM that's why Kconfig it showing it as error:
WARNING: unmet direct dependencies detected for DM_MTD
Depends on [n]: DM [=n]
Selected by [y]:
- NAND_ARASAN [=y] && MTD_RAW_NAND [=y]
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add CONFIG_XILINX_UARTLITE config to versal/zynqmp defconfig to
enable uartlite driver support by default.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enable required configs for using ubifs in uboot.
UBIFS testing procedure from u-boot:
Let's say we have two partitions in dt as below and want to format
partition1 "images" with ubifs.
partition@0 {
label = "boot";
reg = <0x0 0x1000000>;
};
partition@1 {
label = "images";
reg = <0x1000000 0x7000000>;
};
We will format the partition from linux and copy some files and access
from uboot later.
First thing, in linux config disable CONFIG_MTD_SPI_NOR_USE_4K_SECTORS.
this is required as ubifs expects min LEB size as 15*1024 bytes.
Use below commands in linux to format "images" partition with ubifs.
ubiformat /dev/mtd1
ubiattach /dev/ubi_ctrl -m 1
ubimkvol /dev/ubi0 -N images -m
mount -t ubifs ubi0:images /mnt
We can copy files to /mnt and unmount it.
To access this ubifs partition from uboot, run below commands.
(Don't forget to probe device before, e.g. sf probe 0 0 0)
setenv mtdids "nor0=nor0"
setenv mtdparts "mtdparts=nor0:16m(boot),112m(images)"
ubi part images
ubifsmount ubi0:images
make sure we match "mtdparts" to whatever is given in dt w.r.t partition
sizes.
"mtdparts" command will list the mtd partitions in u-boot.
Once ubifs is mounted, we can use "ubifsls" to list the files in that
partition and use "ubifsload <addr> <filename>" to load files from ubifs
partition to DDR.
Reading information about mtd layout from DT is not supported.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Do not source xilinx board Kconfig by other boards. These configs should be
available only when Xilinx platforms are selected.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
CONFIG_BLK needs to be enabled by default to allow U-Boot to
compile after a 'make pic32mzdask_defconfig'.
Signed-off-by: John Robertson <john.robertson@simiatec.com>
Setting CONFIG_ENV_ADDR to something other than 0 stops gd->env_addr
from being allocated dynamically. When the environment is in SPI we need
it to be allocated as we can't use a direct memory mapped address.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Silence the "Driver Model for Ethernet drivers" migration warning for
the bcm7445 and bcm7260 ports, neither of which supports networking yet.
Signed-off-by: Thomas Fitzsimmons <fitzsim@fitzsim.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This is not required for sysboot (we defined fdtfile), let's save a few
bytes in the binary image without these variables.
Signed-off-by: Soeren Moch <smoch@web.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The Toradex product is called apalis-imx8 consisting of SoM with
i.MX8QM and i.MX8QP SoCs.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
The Toradex product is called colibri-imx8x consisting of SoM with
i.MX8QXP and i.MX8DX SoCs.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
The size of the binary created with the default U-boot config is much
greater than the default offset for environment `0x60000`.
In case if that binary is used for booting via MMC it is overlapped with
the environment stored on MMC.
This leads to U-Boot corruption while saving environment with `saveenv`
command and non-bootable SabreLite board.
The offset for environment `CONFIG_ENV_OFFSET=0x60000` was added in
commit a09fea1 but did not count in the change to `0xC0000` if option
`CONFIG_ENV_IS_IN_MMC` is used.
The offset is also used for variant with environment saving onto SPI NOR
flash (with enabled option `CONFIG_ENV_IS_IN_SPI_FLASH`). In that case the
U-Boot binary flashed on SPI NOR is also corrupted after environment
saving with the original 0x60000 offset.
Signed-off-by: Denis Pynkin <denis.pynkin@collabora.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable and set preboot var with fdtfile evaluation.
preboot will be checked and run immediately before starting the
CONFIG_BOOTDELAY countdown and/or running the auto-boot command resp.
entering interactive mode.
This provides possibility to use different boot cmds in interactive mode
without manual setting fdtfile value, as it it's already evaluated
before entering interactive mode.
Fixes: a62c60610f("colibri_imx7_emmc: add Colibri iMX7D 1GB (eMMC) module support")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Enable and set preboot var with fdtfile evaluation.
preboot will be checked and run immediately before starting the
CONFIG_BOOTDELAY countdown and/or running the auto-boot command resp.
entering interactive mode.
This provides possibility to use different boot cmds in interactive mode
without manual setting fdtfile value, as it it's already evaluated
before entering interactive mode.
Fixes: 304042c1f3("colibri_vf: set fdtfile for distroboot")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Enable and set preboot var with fdtfile evaluation.
preboot will be checked and run immediately before starting the
CONFIG_BOOTDELAY countdown and/or running the auto-boot command resp.
entering interactive mode.
This provides possibility to use different boot cmds in interactive mode
without manual setting fdtfile value, as it it's already evaluated
before entering interactive mode.
Fixes: board: 31b1e17f44("toradex: add Colibri iMX6ULL support")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
enable DTS support for keymile mpc83xx based boards.
get rid of compile warning:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Therefore done:
- add DTS for all mpc83xx based boards from keymile
mainly they are not mainlined to linux.
- add u-boot specific dtsi
- add stdout-path
- add missing ucc4 par_io definitions, which were
in board code, but not in linux DTS
- remove not used ethernet nodes
Signed-off-by: Heiko Schocher <hs@denx.de>
Patch-cc: Mario Six <mario.six@gdsys.cc>
Patch-cc: Qiang Zhao <qiang.zhao@nxp.com>
Series-to: u-boot
Series-version: 3
Series-changes: 3
- rebase patchset to current mainline commit
c0192950df
- update defconfig files
Series-changes: 2
- add patch which fixes Codingstyle errors in drivers/qe
- add patch which converts the mpc83xx based boards from
keymile to DM_ETH
Cover-letter:
powerpc, mpc83xx: add DM_ETH support
This patch series adds DM ethernet support for mpc83xx based
keymile boards.
Travis build:
END
am335x internal SRAM is too small to support the addition of
SPI bootmode to the default defconfig. Add a separate spiboot_defconfig
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Enable the FS_LOADER and associated configs in the j7200_evm_r5_defconfig
so that the R5 SPL can support the loading of firmware files from a boot
media/file system.
Signed-off-by: Suman Anna <s-anna@ti.com>
The A72 U-boot can support early booting of any of the Main or MCU R5F
remote processors from U-boot prompt to achieve various system usecases
before booting the Linux kernel. Update the default BOOTCOMMAND to provide
an automatic and easier way to start various remote processors through
added environment variables.
Signed-off-by: Suman Anna <s-anna@ti.com>
The J7200 SoCs has two R5F sub-systems. Enable the TI K3
R5F remoteproc driver and the remoteproc command options
to allow these R5F processors to be booted from A72 U-Boot.
The Kconfigs are added using savedefconfig.
Signed-off-by: Suman Anna <s-anna@ti.com>
Enable configs required to support HyperFlash boot and detection of
onboard mux switch for HyperFlash selection
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Enable options SYS_WHITE_ON_BLACK to permit HDMI background
screen from white to back, also enable USB_KEYBOARD.
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Supporting USB keyboards out of the box is both handy for development
and production. Notably if u-boot is used to boot into GRUB. This patch
adds USB keyboard support for 32 bit RPi4 config.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Enable support of ISSI SPI flashes found on EspressoBIN boards
Change-Id: I6de61c48f108fb4f410f321b9db45887d23212e5
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-on: http://vgitil04.il.marvell.com:8080/61455
Tested-by: iSoC Platform CI <ykjenk@marvell.com>
Reviewed-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Reviewed-by: Stefan Chulski <stefanc@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Include support for CONFIG_SPI_FLASH_GIGADEVICE for supporting
newly produces EspressoBin boards (v7)
Change-Id: I5d4b972cbe2ee5a9d52ce9908794ad4e1b59ee3b
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-on: http://vgitil04.il.marvell.com:8080/61236
Tested-by: iSoC Platform CI <ykjenk@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
For testing automated updates via dfu and mtd we need the dfu and mtd
commands as well as preboot support.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Due to different partition layouts in different U-Boot versions, DTS for
Espressobin in Linux does not contain any definition of MTD partitions.
See commit https://git.kernel.org/stable/c/00954566464a4 for more details.
This patch via ft_board_setup() hook fills current partition layout used by
U-Boot, so booted kernel would see correct MTD partitions layout.
U-Boot env partition is calculated from CONFIG_ENV_OFFSET option.
First partition contains secure firmware, ARM trusted firmware and U-Boot
with checksums. So it is not possible to replace just one image (e.g.
U-Boot) without updating other parts where is stored checksum of U-Boot.
Therefore there is no extra partition defined for U-Boot and first
partition is called just 'firmware'.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Konstantin Porotchkin <kostap@marvell.com>
Tested-by: Andre Heider <a.heider@gmail.com>
Espressobin board comes with Marvell's U-Boot version where U-Boot env is
stored in SPI at offset 0x3F0000. This patch changes env offset in
Espressobin defconfig file to match Marvell's U-Boot version.
Users who want to use previous or different env offset can still change it
in .config file when compiling U-Boot.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Andre Heider <a.heider@gmail.com>
Enabled SDIO slot 0 (south bridge) for SD card on
Espressobin board.
Change-Id: I51a2debf9fba276b9c4a2bc6da91328d47f443e3
Signed-off-by: Wilson Ding <dingwei@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-on: http://vgitil04.il.marvell.com:8080/60945
Tested-by: iSoC Platform CI <ykjenk@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
[pali: Define cd-gpios and enable CONFIG_DM_REGULATOR_GPIO]
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Andre Heider <a.heider@gmail.com>
CMD_ADC selected DM_REGULATOR unconditionally without enabling DM.
That's why change select to depends on to cover it.
Kconfig is showing this issue as:
WARNING: unmet direct dependencies detected for REGMAP
Depends on [n]: DM [=n]
Selected by [y]:
- DM_REGULATOR_PBIAS [=y] && DM_REGULATOR [=y]
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Update CMD_ADC=y configs to enable DM_REGULATOR now]
Signed-off-by: Tom Rini <trini@konsulko.com>
- Add basic Marvell/Cavium OcteonTX/TX2 support (Suneel)
- Infrastructure changes to PCI uclass to support these SoC's (Suneel)
- Add PCI, MMC & watchdog driver drivers for OcteonTX/TX2 (Suneel)
- Increase CONFIG_SYS_MALLOC_F_LEN for qemu-x86 (Stefan)
- Sipeed Maix support S-mode.
- Provide command sbi.
- Use fdtdec_get_addr_size_auto_parent to get fu540 cache base address.
- Fix a compiler error with CONFIG_SPL_SMP=n.
- Fix sifive ram driver 32 compiler warnings.
- Fix kendryte/pll.h redefine nop() warning.
With the upcoming increase of the malloc area in U-Boot
("pci: pci-uclass: Dynamically allocate the PCI regions"), the CI QEMU
x86 test fails:
U-Boot 2020.10-rc2-g0a668f6d38 (Aug 25 2020 - 06:12:51 +0000)
alloc space exhausted
Error binding driver 'cpu_qemu': -12
Some drivers failed to bind
alloc space exhausted
initcall sequence fff6a760 failed at call fff13b3d (err=-19)
This patch now increases CONFIG_SYS_MALLOC_F_LEN to 0x1000, which is
already used on qemu-x86_64_defconfig.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
As explained in the CONFIG_DM_MDIO text inside drivers/net/Kconfig:
"Useful in particular for systems that support
DM_ETH and have a stand-alone MDIO hardware block shared by multiple
Ethernet interfaces."
i.MX6 has a single FEC instance, so there is no need to select
CONFIG_DM_MDIO.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
We have a number of platforms that are a combination of a carrier board
and System-on-Module (SoM) that in turn allows for the board to have
different SoCs on it. In some cases, this is handled via board-specific
Kconfig options. In other cases we make use of
CONFIG_SYS_EXTRA_OPTIONS. This latter case however can lead to invalid
configurations as we will not in turn get options that in Kconfig are
selected by or depend on that setting.
To resolve this, make the SoC option a choice in Kconfig and make boards
depend on what they can support. This change opens us up for further
clean-ups in the cases where a single CONFIG_TARGET_xxx can support
different SoCs and today they do not, or do not cleanly do so.
Reported-by: Matt Porter <mporter@konsulko.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: "NXP i.MX U-Boot Team" <uboot-imx@nxp.com>
Cc: Soeren Moch <smoch@web.de>
Cc: Markus Niebel <Markus.Niebel@tq-group.com>
Cc: Igor Opaniuk <igor.opaniuk@toradex.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Andreas Geisreiter <ageisreiter@dh-electronics.de>
Cc: Ludwig Zenz <lzenz@dh-electronics.de>
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Akshay Bhat <akshaybhat@timesys.com>
Cc: Ken Lin <Ken.Lin@advantech.com.tw>
Cc: Ian Ray <ian.ray@ge.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Raffaele RECALCATI <raffaele.recalcati@bticino.it>
Cc: Simone CIANNI <simone.cianni@bticino.it>
Cc: Adam Ford <aford173@gmail.com>
Cc: Marcin Niestroj <m.niestroj@grinn-global.com>
Cc: "Eric Bénard" <eric@eukrea.com>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Jason Liu <jason.hui.liu@nxp.com>
Cc: Ye Li <ye.li@nxp.com>
Cc: Eric Nelson <eric@nelint.com>
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Parthiban Nallathambi <parthiban@linumiz.com>
Cc: Marek Vasut <marex@denx.de>
Cc: "Sébastien Szymanski" <sebastien.szymanski@armadeus.com>
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: Niel Fourie <lusus@denx.de>
Cc: Martyn Welch <martyn.welch@collabora.com>
Cc: Richard Hu <richard.hu@technexion.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Boris Brezillon <bbrezillon@kernel.org>
Cc: Arkadiusz Karas <arkadiusz.karas@somlabs.com>
Cc: Breno Lima <breno.lima@nxp.com>
Cc: Francesco Montefoschi <francesco.montefoschi@udoo.org>
Cc: Silvio Fricke <open-source@softing.de>
Tested-by: Matt Porter <mporter@konsulko.com> [colibri_imx6]
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marcin Niestroj <m.niestroj@grinn-global.com>
This patch adds support for all OcteonTX2 96xx/95xx
boards from Marvell.
For 96xx boards, use octeontx_96xx_defconfig and
for 95xx boards, use octeontx_95xx_defconfig.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
This patch adds support for all OcteonTX 81xx/83xx
boards from Marvell.
For 81xx boards, use octeontx_81xx_defconfig and
for 83xx boards, use octeontx_83xx_defconfig.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Enable PCI memory regions in ranges property to be of multiple entry.
This helps to add support for SoC's like OcteonTX/TX2 where every
peripheral is on PCI bus.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Provide a defconfig that can be used to build U-Boot for the Maix boards
running upon OpenSBI.
Update the documentation.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
CONFIG_CMD_RUN is set on by default in Kconfig.
Create xenguest_arm64_defconfig by using savedefconfig to avoid unnecessary
options.
Signed-off-by: Anastasiia Lukianenko <anastasiia_lukianenko@epam.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Total Compute is based on ARM architecture and has
the following features enabled in u-boot:
- PL011 UART
- PL180 MMC
- NOR Flash
- FIT image with Signature
- AVB
Signed-off-by: Usama Arif <usama.arif@arm.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPLASH_SCREEN
CONFIG_SPLASH_SCREEN_ALIGN
CONFIG_SPLASHIMAGE_GUARD
CONFIG_SPLASH_SOURCE
Signed-off-by: Simon Glass <sjg@chromium.org>
Remove adhoc dt binding for fixed-partition definition for i2c eeprom.
fixed-partition are using reg property instead of offset/size pair.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Enable DFU tftp support for firmware update. Fill dfu_ram_tftp variable to
have command present for showing how to use it.
boot FIT image has been created from below fragment. Key part is that type
of image has to be firmware. Also based on experiment load property is
completely ignored and base addresses are taken from dfu_alt_info variable.
$ cat update_uboot.its
/dts-v1/;
/ {
description = "Automatic U-Boot update";
#address-cells = <1>;
images {
Image {
description = "Kernel";
data = /incbin/("/tftpboot/Image");
compression = "none";
arch = "arm64";
type = "firmware";
os = "linux";
load = <0x80000>;
entry = <0x80000>;
hash-1 {
algo = "sha1";
};
};
system.dtb {
description = "DTB";
data = /incbin/("/tftpboot/system.dtb");
compression = "none";
arch = "arm64";
type = "firmware";
load = <0>;
hash-1 {
algo = "sha1";
};
};
};
};
$ mkimage -f update_uboot.its /tftpboot/boot
When U-Boot starts get IP address and server IP.
dhcp
setenv serverip 192.168.0.105
And then run prepared command.
run dfu_ram_tftp
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
- Remove pinmux definition from pico-imx6ul.c
- Enable NET_RANDOM_ETHADDR for temporary solution, because micrel_ksz8xxx
driver does not support DM_ETH yet, so cannot read MAC address directly.
Before enable DM_ETH:
Net: FEC [PRIME]
After enable DM_ETH:
Net:
Warning: using random MAC address - ca:3f:43:8f:67:d4
eth1: ethernet@20b4000
Here is the test commands:
=> dhcp
BOOTP broadcast 1
DHCP client bound to address 10.88.88.94 (139 ms)
*** ERROR: `serverip' not set
Cannot autoload with TFTPGET
=> ping 8.8.8.8
Using ethernet@20b4000 device
host 8.8.8.8 is alive
Signed-off-by: Wig Cheng <wig.cheng@technexion.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
It's due to the warning messages issue after compiled:
===================== WARNING ======================
This board does not use CONFIG_DM_VIDEO Please update
the board to use CONFIG_DM_VIDEO before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Enable DM_VIDEO can fix it on the stage of compilation.
Signed-off-by: Wig Cheng <wig.cheng@technexion.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add initial infrastructure for Xen para-virtualized block device.
This includes compile-time configuration and the skeleton for
the future driver implementation.
Add new class UCLASS_PVBLOCK which is going to be a parent for
virtual block devices.
Add new interface type IF_TYPE_PVBLOCK.
Implement basic driver setup by reading XenStore configuration.
Signed-off-by: Andrii Anisov <andrii_anisov@epam.com>
Signed-off-by: Anastasiia Lukianenko <anastasiia_lukianenko@epam.com>
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Add support for Xen para-virtualized serial driver. This
driver fully supports serial console for the virtual machine.
Please note that as the driver is initialized late, so no banner
nor memory size is visible.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Signed-off-by: Anastasiia Lukianenko <anastasiia_lukianenko@epam.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Introduce a minimal Xen guest board running as a virtual
machine under Xen Project's hypervisor [1], [2].
Part of the code is ported from Xen mini-os and also uses
work initially done by different authors from NXP: please see
relevant files for their copyrights.
[1] https://xenbits.xen.org
[2] https://wiki.xenproject.org/
Signed-off-by: Andrii Anisov <andrii_anisov@epam.com>
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Signed-off-by: Anastasiia Lukianenko <anastasiia_lukianenko@epam.com>
Switch DTB provider form OF_EMBED to OF_SEPARATE
to avoid the compile warning message:
==================== WARNING ======================
CONFIG_OF_EMBED is enabled. This option should only
be used for debugging purposes. Please use
CONFIG_OF_SEPARATE for boards in mainline.
See doc/README.fdt-control for more info.
====================================================
Signed-off-by: Chia-Wei, Wang <chiawei_wang@aspeedtech.com>
Move the BOOTCOMMAND definition from the board inclusion
header to the default configuration file.
Signed-off-by: Chia-Wei, Wang <chiawei_wang@aspeedtech.com>
- Add STM32 FMC2 EBI controller driver
- Fix dwc3-sti-glue which allows STiH410-B2260 to boot again
- Add fitImage its entry for 587-200 DHCOR SoM
- Add both PDK2 and DRC02 DT into DHCOM fitImage its
- Fix DHCOM KS8851 ethernet MAC address
- Remove stm32mp1 board.c file
- Use const for struct node_info in board stm32mp1.c file
-----BEGIN PGP SIGNATURE-----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=J4aq
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20200813' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- Use IS_ENABLED to prevent ifdef in board_key_check for STM32MP
- Add STM32 FMC2 EBI controller driver
- Fix dwc3-sti-glue which allows STiH410-B2260 to boot again
- Add fitImage its entry for 587-200 DHCOR SoM
- Add both PDK2 and DRC02 DT into DHCOM fitImage its
- Fix DHCOM KS8851 ethernet MAC address
- Remove stm32mp1 board.c file
- Use const for struct node_info in board stm32mp1.c file
Include both PDK2 and DRC02 DTs in the DHCOM fitImage .its and implement
support in SPL to select the correct configuration entry for U-Boot by
using the machine compatible string from SPL DT.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
This patch enables the support of FMC2 EBI.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Because of space constraints, create a new USB defconfig for R5 to
faciliate booting from USB mass storage devices
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Because of space constraints, create a new USB defconfig for R5 to
faciliate booting in USB peripheral (DFU) bootmode
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
This commit completes the migrations for DM_ETH and DM_USB. The board
is now consistent with omap3_beagle and other remaining OMAP3 boards.
Cc: Tom Rini <trini@konsulko.com>
Cc: Adam Ford <aford173@gmail.com>
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
This converts the following to Kconfig:
CONFIG_SYS_MMC_ENV_DEV
CONFIG_SYS_MMC_ENV_PART
Note that with this conversion we now have consistent behavior with
respect to ensuring that we have always selected the correct MMC
device and hardware partition.
Signed-off-by: Tom Rini <trini@konsulko.com>
Add Python scripts to test 'ls' and 'load' commands. The scripts
generate a SquashFS image and clean the directory after the assertions,
or if an exception is raised.
Signed-off-by: Joao Marcos Costa <joaomarcos.costa@bootlin.com>
Add various fixes and improvements to this command that were missed in
the original version. Unfortunately I forgot to send v2.
- Fix Kconfig name
- Use a separate variable for the remaining search length
- Correct a minor bug
- Move into a separate test suite
- Add -q flag to the 'quiet' test to test operation when console is enabled
- Enable the feature for sandbox
Signed-off-by: Simon Glass <sjg@chromium.org>
Update the MikroTik CRS305-1G-4S flash layout to support redundant UBI
partitions.
Additionally enable the UBI commands in crs305-1g-4s_defconfig.
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Jakov Petrina <jakov.petrina@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
MikroTik CRS328-4C-20S-4S board has a switch chip with an integrated
Marvell Prestera 98DX3236 CPU.
This commit includes two board variants, namely the factory
default one and a Bit variant. The Bit board variant has a
bigger Macronix flash.
Add basic U-Boot, UART and SPI flash support.
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Jakov Petrina <jakov.petrina@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
MikroTik CRS326-24G-2S board has a switch chip with an integrated
Marvell Prestera 98DX3236 CPU.
This commit includes two board variants, namely the factory
default one and a Bit variant. The Bit board variant has a
bigger Macronix flash.
Add basic U-Boot, UART and SPI flash support.
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Jakov Petrina <jakov.petrina@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
MikroTik CRS305-1G-4S Bit board has a switch chip with an integrated
Marvell Prestera 98DX3236 CPU.
The Bit board variant is added, which has a bigger Macronix flash.
Add basic U-Boot, UART and Winbond SPI flash support.
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Jakov Petrina <jakov.petrina@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
This commit moves CONFIG_PREBOOT="usb start" to common/KConfig
for all boards also declaring USB_KEYBOARD.
Besides simplifying defconfig files, this also enables support for
board-specific CONFIG_PREBOOT for sunxi boards:
commit 37304aaf60 ("Convert CONFIG_USE_PREBOOT and CONFIG_PREBOOT to
Kconfig") intended to support CONFIG_PREBOOT, but
include/configs/sunxi-common.h hardcodes preboot as part of internally
defined CONSOLE_STDIN_SETTINGS, silently ignoring any board-specific
CONFIG_PREBOOT.
Signed-off-by: Jonas Smedegaard <dr@jones.dk>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Series-Cc: Jagan Teki <jagan@amarulasolutions.com>
Series-Cc: Lukasz Majewski <lukma@denx.de>
Series-Cc: Andre Przywara <andre.przywara@arm.com>
-----------
- fixes for Toradex board
- fix warnings from previous PR
- HAB: reset instead of panic after failure
- new board: MYiR Tech MYS-6ULX
- mx6cuboxi: use OF_PLATDATA
- further changes for DM
Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/714513163
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQS2TmnA27QKhpKSZe309WXkmmjvpgUCXykjtQ8cc2JhYmljQGRl
bnguZGUACgkQ9PVl5Jpo76a1WQCcD+objdS+90mDdT0yTpW3jHS4YiwAn2V2rTTo
4hKj5yxRg3cvb/pBAmbQ
=TyRs
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20200804' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
For 2020.10
-----------
- fixes for Toradex board
- fix warnings from previous PR
- HAB: reset instead of panic after failure
- new board: MYiR Tech MYS-6ULX
- mx6cuboxi: use OF_PLATDATA
- further changes for DM
Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/714513163
Migration to DM_VIDEO changed the output device name (in stout, stderr)
from 'vga' to 'vidconsole'. This also was adapted in the default environment.
However, existing user defined environments still use 'vga'. Enable this
workaround to map the 'vga' name to 'vidconsole'. So we get HDMI video
output also with existing legacy environments.
Signed-off-by: Soeren Moch <smoch@web.de>
This patch enables the following options for the Octeon EBB7304 EVB:
- PCI & DM_PCI
- DM_SPI_FLASH & SPI flash device support
- SPI & Octeon SPI driver
- GPIO cmd support
- I2C cmd support
Signed-off-by: Stefan Roese <sr@denx.de>
Before enable _DM_ETH:
Net: FEC [PRIME]
After enable DM_ETH:
Net: eth0: ethernet@2188000
Here is the test commands:
=> dhcp
BOOTP broadcast 1
DHCP client bound to address 10.88.88.152 (146 ms)
*** ERROR: `serverip' not set
Cannot autoload with TFTPGET
=> ping 8.8.8.8
Using ethernet@2188000 device
host 8.8.8.8 is alive
Signed-off-by: Wig Cheng <wig.cheng@technexion.com>
Enable CONFIG_SPL_DM_SPI_FLASH to be able to boot from SPI NOR,
modify the offset of U-boot proper in the SPI NOR, so the
difference in offset matches between SPL and U-boot matches that of
the SD Card, allowing u-boot-with-spl.imx to also be copied to SPI
NOR at an offset of 0x400. Update the README to reflect this
change.
Signed-off-by: Niel Fourie <lusus@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
MYS-6ULX is single board computer (SBC) comes with eMMC or NAND based
on imx6ULL SoC from NXP and provision for expansion board. This
commit adds support only for SBC with NAND.
CPU: Freescale i.MX6ULL rev1.1 528 MHz (running at 396 MHz)
CPU: Commercial temperature grade (0C to 95C) at 45C
Reset cause: WDOG
Model: MYiR i.MX6ULL MYS-6ULX Single Board Computer with NAND
Board: MYiR MYS-6ULX 6ULL Single Board Computer
DRAM: 256 MiB
NAND: 256 MiB
MMC: FSL_SDHC: 0
In: serial@2020000
Out: serial@2020000
Err: serial@2020000
Net: FEC0
Working:
- Eth0
- MMC/SD
- NAND
- UART 1
- USB host
Signed-off-by: Parthiban Nallathambi <parthiban@linumiz.com>
Enable these extra PCI ethernet devices, so they can be tested in CI.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Switch r2dplus to DM and DT probing for serial and clock.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The ethernet on r2dplus is on PCI bus, enumerate the PCI early
to get the ethernet operational.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Enable DM ethernet support for the board, now that rtl8139 is converted.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
As both MMC and GPIO driver now supports OF_PLATDATA, enable it in
defconfig in order to reduce the SPL footprint. After applying this
setting the SPL reduction is 5 KB, which partially compensates the
increment due to DM.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support of environment location with the new env command:
'env select' and 'env load'
The ENV backend is selected by priority order
- 0 = "nowhere" (default at boot)
- 1 = "EXT4"
To test EXT4 env support, this backend is selected by name:
> env select EXT4
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Activate ENV in EXT4 support in sandbox.
The sandbox behavior don't change; the default environment with
the nowhere backend (CONFIG_ENV_IS_NOWHERE)is still used:
the weak function env_get_location() return ENVL_NOWHERE for priority 0.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Refactor to allow any arch to create SPI-flash images
New button uclass
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl8g33sRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreaeEgf/QhmJjd6lEE3ABncRa3texyqq7j9eu+9P
2JMCahrIzps83LLOkzNSGs1+m1hRuTcdnYNV8FxdmkAjDTYwV5RHOfwtpAr2nkH2
HBbJRA2qMPleqT8wcymouhaCIRTTCGfUkFgZ+OowwSlHnQ4d2oGU/59Z+AkbpfX0
3svA1Mlr5rUTZ3qTvdsepuZckuYOTGYZ5jgjbgr+G8F4iW4Ov+OkBxqDz9zFCveF
md5CHKP1SV+bq67Q9uqUEwatLzYpy1p24j1Qe4G08U1+XCi6r+95VEc7TWxggboj
eV/5d/sZbGESAtJiJ4TmqpGVcOLzBLI0FOunky0JNFwdcyRS/6KcCg==
=Xjil
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-28jul20' of git://git.denx.de/u-boot-dm
Use binman instead of one of the Rockchip build scripts
Refactor to allow any arch to create SPI-flash images
New button uclass
- fix SPL boot issue due to early dbgmcu_init() call
- fix SPL boot issue due to dcache memory region configuration
- add support of CONFIG_ENV_IS_IN_MMC
- add specific SD/eMMC partition for U-Boot enviromnent
- enable env in SPL
- use "env info -q" to remove log during boot
- remove env location override for dh_stm32mp1
- update management of misc_read
- check result of find_mmc_device in stm32prog
- use regulator_set_enable_if_allowed for disabling vdd supply in usbphyc
- enable CMD_ADTIMG flag to handle Android images
- device tree alignment with Linux Kernel v5.8-rc1
- remove hnp-srp-disable for usbotg on dk1
- add reset support to uart nodes on stm32mp15x
- use correct weak function name spl_board_prepare_for_linux
- use cd-gpios for ST and DHSOM boards
- add seeed studio odyssey-stm32mp157c board support
- move ethernet PHY into SoM DT
- add DHSOM based DRC02 board support
Enable EXT4 and FAT fs support for ns3.
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Enable BCM IPROC mmc driver ns3.
Enable DMA for MMC Host to have better reads and writes.
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add both DRAM banks memory information and
the corresponding MMU page table mappings.
Signed-off-by: Bharat Kumar Reddy Gooty <bharat.gooty@broadcom.com>
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support for Broadcom Northstar 3 SoC.
NS3 is a octo-core 64-bit ARMv8 Cortex-A72 processors
targeting a broad range of networking applications.
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Changes in relation to FriendlyARM's U-Boot nanopi2-v2016.01:
- Configuration changed, mainly several "CONFIG_..." moved from
s5p4418_nanopi2.h to s5p4418_nanopi2_defconfig and USB related
configs removed because USB is not supported yet.
- s5p4418_nanopi2.h: "CONFIG_" removed from several s5p4418/nanopi2
specific defines because the appropriate values do not need to be
configurable.
- pinctrl is supported now, therefore "CONFIG_PINCTRL=y" added to
s5p4418_nanopi2_defconfig.
Signed-off-by: Stefan Bosch <stefan_b@posteo.net>
The QEMU/mach-virt targeted port of u-boot currently only runs on
QEMU under TCG emulation, which does not model the caches at all,
and so no users can exist that are relying on the GRUB hack for
EFI boot.
We will shortly enable support for running under KVM, but the GRUB
hack (which disables all caches without doing cache cleaning by VA
during ExitBootServices()) is likely to cause more problems than it
solves, given that KVM hosts require correct maintenance if they
incorporate non-architected system caches.
So let's disable the GRUB hack by default on the QEMU/mach-virt
port.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
QEMU's mach-virt machine only supports selecting CPU models that
implement the virtualization extensions, and are therefore guaranteed
to support LPAE as well.
Initially, QEMU would not allow emulating these CPUs running in HYP
mode (or EL2, for AArch64), but today, it also contains a complete
implementation of the virtualization extensions themselves.
This means we could be running U-Boot in HYP mode, in which case the
LPAE long descriptor page table format is the only format that is
supported. If we are not running in HYP mode, we can use either.
So let's enable CONFIG_ARMV7_LPAE for qemu_arm_defconfig so that we
get the best support for running with the MMU and caches enabled at
any privilege level.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Acked-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Enable the support of button (driver and command) on sandbox.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Enable the support of button (driver and command) on sandbox64.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
At present there is not enough space for U-Boot due to the EFI loader.
Correct this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This board does not have microcode but at present that is not supported
by Kconfig nor the binman image layout. Fix both of these.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present the image layout is not correct, since it uses the SDRAM
address of the 64-bit U-Boot as the ROM address. Fix this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present this board uses a custom script to produce the .its file.
Update it to use binman instead. Binman can create all the images that
are needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present this board uses a custom script to produce the .its file.
Update it to use binman instead. Binman can create all the images that
are needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we use the empty string to indicate that there is no FIT
generator, but this doesn't allow an individual board to undefine it.
Create a separate bool instead.
Update the config of the boards which currently have an empty string.
Signed-off-by: Simon Glass <sjg@chromium.org>
This Kconfig is not needed anymore since U-Boot will build the ROM if the
required binary blobs exist.
The BUILD_ROM environment variable used to request that the ROM be built.
Now this always happens if the required binary blobs are available. Update
it to mean that U-Boot should fail if the ROM cannot be built. This
behaviour should be compatible with how it used to work.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Update the config for chromebook_bob to support booting from SPI flash.
The existing SPL size is too small since ATF is needed, so double it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Linux distributions generally use the "make defconfig && make tools-all"
recipe to generate a uboot-tools (or similar) package.
This patch enables FIT cipher support in the default mkimage build.
Signed-off-by: Patrick Oppenlander <patrick.oppenlander@gmail.com>
Done with:
./tools/moveconfig.py -S SPL_LOAD_FIT_ADDRESS
./tools/moveconfig.py -S SPL_LOAD_FIT_ADDRESS -H
Signed-off-by: Peng Fan <peng.fan@nxp.com>
[trini: A few more migrations]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_NAND_DRIVERS
CONFIG_SPL_NAND_ECC
CONFIG_SPL_NAND_SIMPLE
Signed-off-by: Adam Ford <aford173@gmail.com>
This converts the following to Kconfig:
CONFIG_ENV_OVERWRITE
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rerun migration, remove some comments]
Signed-off-by: Tom Rini <trini@konsulko.com>
Activate the support of the command adtimg to handle android images.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Activate env config in SPL with CONFIG_SPL_ENV_SUPPORT
and use CONFIG_IS_ENABLED macro to test the activated
CONFIG_$(SPL_)ENV_IS_IN_... in env_get_location.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Save the environment at the end of the U-Boot partition, the GPT
partition named "ssbl" in SD card or eMMC and avoid requirements
on the "bootfs" file system generated via specific raw tools
(like wic and genimage).
With the previous configuration of the U-Boot environment saved in ext4
file, U-Boot need to create/modify the file uenv.txt in the ext4 file
system; so this EXT4 file system need to be generated without some
functionality, like metadata_csum and dir_index, because they are not
supported by U-Boot.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
- Bug fixes and updates on ls2088a,ls1028a, ls1046a, ls1043a, ls1012a
- lx2-watchdog support
- layerscape: pci-endpoint support, spin table relocation fixes and
cleanups
- fsl-crypto: RNG support and bug fixes
1. Configure white on black for video console.
2. Enable printing bmp logo during late board init stage.
3. Use iomux configuration from device tree.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Restore CONFIG_ENV_ADDR value to fix boot hang with IFC-NOR
which is default boot source.
Signed-off-by: Ashish Kumar <ashish.kumar@nxp.com>
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Add Root Complex and Endpoint mode specific config entries, such that
it's feasible to enable the RC and/or EP mode driver indepently.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Enable support for sub command 'env info' in sandbox
with CONFIG_CMD_NVEDIT_INFO. This is aimed primarily
at adding unit test.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Enable CONFIG_SOC_DEVICE and CONFIG_SOC_DEVICE_TI_K3 so the TI K3 SoC
driver can be used for SoC detection.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Enable CONFIG_SOC_DEVICE and CONFIG_SOC_DEVICE_TI_K3 so the TI K3 SoC
driver can be used for SoC detection.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Add a sandbox SOC driver, and some tests for the SOC uclass.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
The Beacon EmbeddedWorks kit is based on the R8A774A1 SoC also
known as the RZ/G2M.
The kit consists of a SOM + Baseboard and supports microSD,
eMMC, Ethernet, a couple celular radios, two CAN interfaces,
Bluetooth and WiFi.
Signed-off-by: Adam Ford <aford173@gmail.com>
Add Kconfig entries for the dc2114x driver and convert various boards.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
- Fix SiFive HiFive Unleashed board booting failure problem.
- Enable SiFive fu540 PWM driver.
- Support SiFive fu540: SPI boot.
- Update OpenSBI used for RISC-V CI testing.
- Revert "riscv: Allow use of reset drivers".
- Revert "Revert "riscv: sifive: fu540: Add gpio-restart support"".
- sysreset: syscon:
- Don't assume default value for offset and mask property.
- Support value property.
- qemu: Add syscon reboot and poweroff support.
- Fix SIFIVE debug serial dependency.
- Fix linking error when building u-boot-spl with no SMP support.
- AE350 use fdtdec_get_addr_size_auto_noparent to parse smc reg.
- Make memory node available to SPL in hifive-unleashed-a00-u-boot.dtsi
- SiFive fu540 avoid using hardcoded ram base and size.
Add booting from SPI for SiFive Unleashed board.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
- New rk3326 board: Hardkernel Odroid Go2;
- Update board config and dts for RockPI 4/N8/N10;
- Update led boot on support for roc-rk3399-pc;
- Enable SPI Flash suppor for rk3328 rock64 board;
- Update rockchip pcie phy to use generic framework;
Disable ram rockchip debug driver for ROCKPi N8/N10 boards
since we have verified ram in many instances with respective
U-Boot versions.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable PCI/NVME for M.2 Slot on RockPI-4 boards.
=> nvme info
Device 0: Vendor: 0x144d Rev: 4L1QCXB7 Prod: S35FNX0J623292
Type: Hard Disk
Capacity: 122104.3 MB = 119.2 GB (250069680 x 512)
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable common on board devices for ROCKPi N8.
- USB 2.0 Host
- USB 2.0 OTG/Gadget
- HDMI Out
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable common on board devices for ROCKPi N10.
- USB 2.0 Host
- USB 3.0 Host
- USB 3.0 Gadget
- HDMI Out
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
ROC-RK3399-PC has specific set of configurations for
on-board led setup.
Due to easiness for user to know the state of the board
roc-rk339-pc board code will setup the low power led
on/off, and waiting for user to press power key and then
glow full power led.
All this needs to happen only during power-on-reset not
for soft reset or WDT.
Also, it is not a proper usage to ask the user to press
the Power key if the board connected remotely, so add
the environment variable 'pwr_key' to check as well.
So, user need to press Power key only
- during POR
- pwr_key=y
Tested-by: Suniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
roc-rk3399-pc has some specific requirements to support LEDS,
environment. board detection and etc prior to U-Boot proper.
So as of now SPL would be a better stage for these custom board
requirements to support unlike TPL. Adding few of these custom
requirements like LEDS in TPL would require extra code pulling
and also the size of TPL can grow.
So, this patch moves the leds code from TPL into SPL Board init
led_setup code.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
(split tpl.c change as separate patch)
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Rock PI 4C has AP6256 Wifi/BT, PoE, miniDP, USB Host enabled
GPIO pin change compared to 4B, 4C.
So, add or enable difference nodes/properties in 4C dts
by including common dtsi.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Rock PI 4 has 3 variants of hardware platforms called
RockPI 4A, 4B, and 4C.
- Rock PI 4A has no Wif/BT.
- Rock PI 4B has AP6256 Wifi/BT, PoE.
- Rock PI 4C has AP6256 Wifi/BT, PoE, miniDP, USB Host enable
GPIO pin change compared to 4B, 4C
So move common nodes, properties into dtsi file and include
on respective variant dts files.
Use 4B dts into default rock-pi-4 defconfig until we find any
solution for dynamic detection of these variants.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
To fix below build error:
drivers/usb/host/built-in.o: In function `xhci_dwc3_remove':
drivers/usb/host/xhci-dwc3.c:174: undefined reference to `dwc3_shutdown_phy'
drivers/usb/host/built-in.o: In function `xhci_dwc3_probe':
drivers/usb/host/xhci-dwc3.c:130: undefined reference to `dwc3_setup_phy'
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Disable ram rockchip debug driver for roc-rk3399-pc
boards since we have verified ram in many instances
with respective U-Boot versions.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add U-Boot SPI Flash support for the PINE64 Rock64 board
Signed-off-by: Johannes Krottmayer <krjdev@gmail.com>
Cc: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Adjust the ENV offset, size to fit into all images
on 16MB flash.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable DWC3 core, gadget for roc-rk3399-pc board.
This would help to use fastboot by default.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable config options to get HDMI output on RockPI-4 boards.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable USB gadget for rock-pi-4 boards.
This would help to use fastboot by default.
Note: Connect the Host USB cable (Port A or C) to rock-pi-4
Upper USB 3.0 port.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable PCI/NVME for M.2 Slot on RockPI-4 boards.
=> nvme info
Device 0: Vendor: 0x144d Rev: 2B2QEXM7 Prod: S4EUNG0MC10012Y
Type: Hard Disk
Capacity: 238475.1 MB = 232.8 GB (488397168 x 512)
Cc: Tom Cubie <tom@radxa.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable USB3.0 Host support for RockPI-4 boards.
Note that the Upper USB3.0 port is marked as otg and
lower USB3.0 port marked as host, so this below log
capture when USB3.0 mass storage plug in at lower
USB 3.0 port.
Log:
Bus usb@fe380000: USB EHCI 1.00
Bus usb@fe3c0000: USB EHCI 1.00
Bus dwc3: usb maximum-speed not found
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
Bus dwc3: usb maximum-speed not found
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus usb@fe380000 for devices... 1 USB Device(s) found
scanning bus usb@fe3c0000 for devices... 1 USB Device(s) found
scanning bus dwc3 for devices... 1 USB Device(s) found
scanning bus dwc3 for devices... cannot reset port 1!?
2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
=> usb tree
USB device tree:
1 Hub (480 Mb/s, 0mA)
u-boot EHCI Host Controller
1 Hub (480 Mb/s, 0mA)
u-boot EHCI Host Controller
1 Hub (5 Gb/s, 0mA)
U-Boot XHCI Host Controller
1 Hub (5 Gb/s, 0mA)
| U-Boot XHCI Host Controller
|
+-2 Mass Storage (5 Gb/s, 224mA)
SanDisk Dual Drive 040130e3ee554b7078843f4eb331646
Cc: Tom Cubie <tom@radxa.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable USB3.0 Host support for RockPro64 boards.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Also known as Odroid Go Advance but named Go2 internally by the
vendor it seems.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable CONFIG_SOC_DEVICE and CONFIG_SOC_DEVICE_TI_K3 so the TI K3 SoC
driver can be used for SoC detection.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Enable CONFIG_SOC_DEVICE and CONFIG_SOC_DEVICE_TI_K3 so the TI K3 SoC
driver can be used for SoC detection.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Add a sandbox SOC driver, and some tests for the SOC uclass.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
This patch adds very basic minimal support for the Marvell Octeon 3
CN73xx based EBB7304 EVK. Please note that the basic Octeon port does
not support DDR3/4 initialization yet. To still use U-Boot on with this
port, the L2 cache (4MiB) is used as RAM. This way, U-Boot can boot
to the prompt on this board.
Supported devices:
- UART
- reset
- CFI parallel NOR flash
Signed-off-by: Stefan Roese <sr@denx.de>
- New timer API to allow delays with a 32-bit microsecond timer
- Add dynamic ACPI structs (DSDT/SSDT) generations to the DM core
- x86: Enable ACPI table generation by default
- x86: Enable the copy framebuffer on Coral
- x86: A few fixes to FSP2 with ApolloLake
- x86: Drop setup_pcat_compatibility()
- x86: Primary-to-Sideband Bus minor fixes
----------------
- i.MX DDR driver fix/update for i.MX8M
- i.MX pinctrl driver fix.
- Use arm_smccc_smc to remove imx sip function
- i.MX8M clk update
- support booting aarch32 kernel on aarch64 hardware
- fused part support for i.MX8MP
- imx6: pcm058 to DM
Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/708734785
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQS2TmnA27QKhpKSZe309WXkmmjvpgUCXxCxWw8cc2JhYmljQGRl
bnguZGUACgkQ9PVl5Jpo76bPyACcDZ8gD9jf1P/Zh+7kqrGdIWwURF8AnAiEtNnu
FhE/WQQj4mAEWE4F2bFE
=7ceG
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20200716' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
i.MX for 2020.10
----------------
- i.MX DDR driver fix/update for i.MX8M
- i.MX pinctrl driver fix.
- Use arm_smccc_smc to remove imx sip function
- i.MX8M clk update
- support booting aarch32 kernel on aarch64 hardware
- fused part support for i.MX8MP
- imx6: pcm058 to DM
Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/708734785
This chip is used on coral and we need to generate ACPI tables for sound
to make it work. Add a driver that does just this (i.e. at present does
not actually support playing sound).
Signed-off-by: Simon Glass <sjg@chromium.org>
[bmeng: Use the correct acpi_irq_polarity enum number]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
This chip is used on coral and we need to generate ACPI tables for sound
to make it work. Add a driver that does just this (i.e. at present does
not actually support playing sound).
Signed-off-by: Simon Glass <sjg@chromium.org>
Write required information into the SSDT to describe the SD card
card-detect pin. Since the required GPIO properties are not present in
the device-tree binding, set them manually for now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Enable this feature on chromebook_coral to speed up the display.
With this change, the time taken to print the environment to the display
without CONFIG_CONSOLE_SCROLL_LINES is reduced from 1830ms to 62ms.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Commit 4503299 has a side effect on this board, and build is broken.
Adjust mx6memcal_defconfig to build it again.
Signed-off-by: Stefano Babic <sbabic@denx.de>
As explained in the CONFIG_DM_MDIO text inside drivers/net/Kconfig:
"Useful in particular for systems that support
DM_ETH and have a stand-alone MDIO hardware block shared by multiple
Ethernet interfaces."
i.MX6 has a single FEC instance, so there is no need to select
CONFIG_DM_MDIO.
Remove it from the i.MX6 defconfig files.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
This commit enables imx28 based XEA board's u-boot.sb (SPL) to download
u-boot proper (u-boot.img) via Ymodem protocol.
This is extremely useful in the recovery scenario where u-boot.sb is
downloaded via uuu utility to SDRAM [*], and then one can upload u-boot
proper via serial console to fully debrick the device.
Note - debricking procedure of imx28 devices:
- NXP's original USB based tools (like mxsldr or uuu) expect single
u-boot.sb which is a relic of the old U-Boot (~2013) without SPL and
U-Boot proper distinction.
[*] On Host:
------------
cat << EOF > imx28_xea.lst
uuu_version 1.3.0
SDPS: boot -f /srv/tftp/xea/u-boot.sb
SDPU: done
EOF
Please start picocom:
sudo picocom -b 115200 -s "sz -vv" /dev/ttyUSB1
sudo ./uuu/uuu -V imx28_xea.lst
On the U-boot console one shall see:
Trying to boot from UART
CCC
Then please press CTRL+A, S
and type u-boot.img
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Peng Fan <peng.fan@nxp.com>
as patch
gpio: search for gpio label if gpio is not found through bank name
is now in mainline, but functionality is disabled, we
need to enable
CONFIG_DM_GPIO_LOOKUP_LABEL
for the aristainetos boards.
Signed-off-by: Heiko Schocher <hs@denx.de>
Convert pcm058 support to use device trees and the driver model.
Add rudimentary boot scripts to the environment, expand README.
Signed-off-by: Niel Fourie <lusus@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Current codes assume the OPTEE address is at the end of first DRAM bank.
Adjust the process to allow OPTEE in the middle of first bank.
When OPTEE memory is removed from first bank, it may split the first bank
to two banks, adjust the MMU table for the split case,
Since the default CONFIG_NR_DRAM_BANKS is 4, it is enough, just enlarge
i.MX8MP evk to default to avoid issue.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Silvano di Ninno <silvano.dininno@nxp.com>
Tested-by: Silvano di Ninno <silvano.dininno@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
At this point in time we can now remove our legacy code and switch to
enabling DM for USB and Ethernet.
Cc: Derald D. Woods <woods.technical@gmail.com>
Cc: Adam Ford <aford173@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tested-by: Derald D. Woods <woods.technical@gmail.com>
There are two options that are currently whitelisted, but they
are redundant, because there are not necessary since Kconfig options
exist to basically state the same thing.
CONFIG_DIRECT_NOR_BOOT and CONFIG_USE_NOR are both set together and
only used by the da850 when booting from NOR, however the only time
CONFIG_MTD_NOR_FLASH is configured is when booting from NOR. Since
NOR doesn't need SPL, the options for SPL can be moved to a check for
building SPL instead of checking for NOR.
This patch removes the checks for these two config options and unifies
the checks around the Kconfig option of CONFIG_MTD_NOR_FLASH.
Since this board is the only board that uses these two config options,
they can be removed from the whitelist table.
Signed-off-by: Adam Ford <aford173@gmail.com>
I actually do not see this used these days because eMMC or NAND is used
for non-volatile devices. Dump the burden to maintain this crappy code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently, the supports for the following two ARMv7 SoC groups
are exclusive, because the boot ROM loads the SPL to a different
address:
- LD4, sLD8 (SPL is loaded at 0x00040000)
- Pro4, Pro5, PXs2, LD6b (SPL is loaded at 0x00100000)
This limitation exists only when CONFIG_SPL=y.
Instead of using crappy CONFIG options, checking SPL and SPL_TEXT_BASE
is cleaner.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This requires enabling BRCMSTB PCIe and XHCI_PCI drivers as well as PCI
and USB commands. To get it working one has to call the following commands:
"pci enum; usb start;", thus such commands have been added to the default
"preboot" environment variable. One has to update their environment if it
is already configured to get this feature working out of the box.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Move ADDR_MAP related config options from include/configs/*.h to the
proper place in lib/Kconfig. This has been done using
./tools/moveconfig.py and manual inspection of the generated changes.
This is a preparation to use ADDR_MAP helper on ARM 32bit Raspberry Pi4
board for mapping the PCIe XHCI MMIO, which is above the 4GiB identity
mapping limit.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Supporting USB keyboards out of the box is both handy for development
and production. Notably if u-boot is used to boot into GRUB.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[mb: drop rpi_4_32b_defconfig hunk]
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
This is required in order to access the reset controller used to
initialize the board's xHCI chip.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
This requires enabling BRCMSTB PCIe and XHCI_PCI drivers as well as PCI
and USB commands. To get it working one has to call the following commands:
"pci enum; usb start;", thus such commands have been added to the default
"preboot" environment variable. One has to update their environment if it
is already configured to get this feature working out of the box.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
DM, OF_CONTROL, DM_SPI and other driver model migration
deadlines are expired for this board.
Remove it.
Acked-by: Magnus Lilja <lilja.magnus@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Enable DM_SPI, DM_SPI_FLASH for db-88f6281-bp-nand board.
Cc: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
OF_CONTROL, DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Cc: Lothar Felten <lothar.felten@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
OF_CONTROL, DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Cc: Ash Charles <ash@gumstix.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
OF_CONTROL, DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Cc: Gilles Gameiro <gilles@gigadevices.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
OF_CONTROL, DM_SPI and other driver model migration deadlines
are expired for this board.
Drop it.
Cc: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
OF_CONTROL, DM_SPI and other driver model migration deadlines
are expired for this board.
Drop it.
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
OF_CONTROL, DM_SPI and other driver model migration deadlines
are expired for this board.
Drop it.
Cc: Ash Charles <ash@gumstix.com>
Cc: Steve Sakoman <sakoman@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
DM, DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
DM, DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Enable DM_SPI, DM_SPI_FLASH for siemens rut board.
Build is fine, but not tested.
Cc: Samuel Egli <samuel.egli@siemens.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Enable DM_SPI, DM_SPI_FLASH for siemens pxm2 board.
Build is fine, but not tested.
Cc: Samuel Egli <samuel.egli@siemens.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Enable DM_SPI, DM_SPI_FLASH for siemens thuban board.
Build is fine, but not tested.
Cc: Samuel Egli <samuel.egli@siemens.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Enable DM_SPI, DM_SPI_FLASH for siemens rastaban board.
Build is fine, but not tested.
Cc: Samuel Egli <samuel.egli@siemens.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Enable DM_SPI, DM_SPI_FLASH for siemens etamin board.
Build is fine, but not tested.
Cc: Samuel Egli <samuel.egli@siemens.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Enable DM_SPI, DM_SPI_FLASH for siemens draco board.
Build is fine, but not tested.
Cc: Samuel Egli <samuel.egli@siemens.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Enable DM_SPI for am355x igep003x board.
Build is fine, but not tested.
Cc: Javier Martínez Canillas <javier@dowhile0.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
- Add two- and three-argument versions of CONFIG_IS_ENABLED in
linux/kconfig.h
- Adds a new feature which supports copying modified parts of
the frame buffer to the uncached hardware buffer
- Enable the copy framebuffer on various x86 targets
i2c changes for v2020.10
- Add support for I2C controllers found on Octeon II/III and Octeon TX
TX2 SoC platforms.
- Add I2C controller support for Cortina Access CAxxxx SoCs
- new rtc methods, rtc command, and tests
- imx_lpi2c: Improve the codes to use private data
- stm32f7_i2c.c: Add new compatible "st,stm32mp15-i2c"
- stm32f7_i2c.c: Add Fast Mode Plus support
- pwm: Add PWM driver for SiFive SoC
This patch enables DM_ETH for the following Kirkwood-based LaCie boards:
- d2 Network v2
- Internet Space v2
- 2Big Network v2
- Network Space v2
- Network Space Lite v2
- Network Space Max v2
- Network Space Mini v2
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This patch enables DM_USB and USB_STORAGE for the following
Kirkwood-based LaCie boards:
- d2 Network v2
- Internet Space v2
- 2Big Network v2
- Network Space v2
- Network Space Lite v2
- Network Space Max v2
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This patch switches the SATA driver from mvsata_ide to sata_mv for the
following Kirkwood-based LaCie boards:
- d2 Network v2
- Internet Space v2
- 2Big Network v2
- Network Space v2
- Network Space Lite v2
- Network Space Max v2
- Network Space Mini v2
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This patch converts the following Kirkwood-based LaCie boards to DM,
DM_SPI and DM_SPI_FLASH:
- d2 Network v2
- Internet Space v2
- 2Big Network v2
- Network Space v2
- Network Space Lite v2
- Network Space Max v2
- Network Space Mini v2
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The helios4 is built on the same microsom as the clearfog, by syncing the config
we enable the same featureset that exists in the som on the helios4. The current
config does not boot as some of the clearfog changes needed to be made on the
helios4 also, generally speaking most changes for the clearfog should also be
made on the helios4.
Signed-off-by: Dennis Gilmore <dennis@ausil.us>
Reviewed-by: Stefan Roese <sr@denx.de>
This seems like a more reasonable resolution for this board, since it is
quite slow. It also allows it to work with a 5" LCD display in my lab.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Update the video driver to support this feature and enable it on
minnowmax to speed up the display.
With this change, the time taken to print the environment to the display
without CONFIG_CONSOLE_SCROLL_LINES is reduced from over 13 seconds to
300ms, at 1280x1024.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Update the video driver to support this feature and enable it on link.
Also remove the multi-line scrolling since normal scrolling is fast enough
now.
With this change, the time taken to print the environment to the display
without CONFIG_CONSOLE_SCROLL_LINES is reduced from about 930ms to 29ms.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Update the video driver to support this feature and enable it on samus.
Also remove the multi-line scrolling since normal scrolling is fast enough
now.
With this change, the time taken to print the environment to the display
without CONFIG_CONSOLE_SCROLL_LINES is reduced from about 430ms to 12ms.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Enable this feature on sandbox by updating the SDL driver to have two
framebuffers.
Update the video tests to check that the copy framebuffer is kept in sync.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
In order to allow adding unit tests of the rtc command, add it to the
various sandbox defconfigs.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
commit 2bd261dd17 ("gpio: search for gpio label if gpio is not found through bank name")
disabled DM_GPIO_LOOKUP_LABEL which is needed
in sandbox defconfigs, as we have tests for this
functionality.
Signed-off-by: Heiko Schocher <hs@denx.de>
Odroid C4 is an Amlogic SM1 device, the board config and board documentation
are adapted from the Odroid-N2 support from the same vendor.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
[narmstrong: fix odroid-c4.rst typos and structure]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Add a proper Odroid-N2 board support to handle the Ethernet MAC
address stored in the in-SoC eFuses.
Signed-off-by: Pascal Vizeli <pvizeli@syshack.ch>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
The ARM Juno boards (-r1 and -r2) feature a Silicon Image 3132 PCIe
SATA controller soldered on the board, providing two SATA ports.
Enable the driver and the sata command in the defconfig, to be able to
load images from SATA disks.
Tested by loading kernels and Grub/EFI from an SSD and successfully
booting a Linux system (with and without using UEFI).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
The ARM Juno boards in their -r1 and -r2 variants sport a PCIe
controller, which we configure already in board specific code to be ECAM
compliant. Hence we can just enable the generic ECAM driver to let
U-Boot use PCIe devices.
Add the respective options to the Juno defconfig to enable the PCI
framework and the generic ECAM driver, and initialise the driver upon
loading U-Boot.
Make some functions in the Juno PCIe init code static on the way.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds MAC and PHY related configs (needed for proper
ethernet operations) for Action Semi S700 SoC.
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
- use OPP information in device tree for 800MHz/650MHz support
- ram: inprovments of test command
- solve boot on closed chip when access to DBGMCU_IDC is protected
- stm32prog command: Add "device anme" during USB enumeration
- update configs: activate WATCHDOG and 'env erase' command,
increase teed partition, support SD card after NOR boot by default and
use env info in env_check
- some sboard cleanups: gpio hog in dh board, specific driver for
type-c stusb1600 controller code in a driver move part of code in spl.c
and in common directory
- fix STM32 compatible for dwc_eth_qos driver
- support of new pinctrl ops get_dir_flags/set_dir_flags in stm32 and stmfx
drivers
- vrefbuf: fix a possible overshoot when re-enabling
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl8EgGEACgkQ4rK92eCq
k3V7mwf+N5Iq6CbUPP11mFiNgAFZ5+hcn6gBTWvbjnd+oaIp15hiQrUNusGNFxXe
oyM4fvm12tjuWFlA0U6VtiLhuVQB1Yte048oX+edDCCLGwxkp6cKBHtCaGT14XvY
ow60XInv/dlrINumf8isy+5QlLgT1Cb7aGZN1qRHsUtnHB/IC836KO+hukGRUvk3
Lqz+FbHqitKnL+CIboC2+YzXqG6ZXdixFZVVPmTVd34C8hQOdkExJ//uR/lH/s6f
vjaecs7HpIuKRpKpt5WcoLzTLd1hstqNNhmTbBHmVo+EqIjMkpISUwDpDJNU5pki
BPbdG9VXqb46JLaTtPT+U4gX4yJ3Bw==
=jQCC
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20200707' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- arch and board update for stm32mp15:
- use OPP information in device tree for 800MHz/650MHz support
- ram: inprovments of test command
- solve boot on closed chip when access to DBGMCU_IDC is protected
- stm32prog command: Add "device anme" during USB enumeration
- update configs: activate WATCHDOG and 'env erase' command,
increase teed partition, support SD card after NOR boot by default and
use env info in env_check
- some sboard cleanups: gpio hog in dh board, specific driver for
type-c stusb1600 controller code in a driver move part of code in spl.c
and in common directory
- fix STM32 compatible for dwc_eth_qos driver
- support of new pinctrl ops get_dir_flags/set_dir_flags in stm32 and stmfx
drivers
- vrefbuf: fix a possible overshoot when re-enabling
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAl8DHgAcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyAdDCACFX01IPRmdkNEYrJf0
YfhQPAPZ/5EyHBv36ePl93CbIRnJPpnrGbBXe8+/Jdcq7l6EkJh2cuO+t9axXner
m0kH35LzLiR9Olz6q5Su0InPWpnDtXxtIczK5v7ZHBeMZ2so763e7SQ2VIMyJJb/
VT6hilqJK6+W1c2X1wmzxyh/nnv/bDBz97cavJN1EKw1arYr8jh/8/tpABk5msDm
J6Z5WsS/CYk7cj6hX7dSNRfqcKsjl/gCYjnVssfgaP1sH+NX0mtS8C6zchNILmpB
2T/dKnpYBBAWTD5fGNVKxKphAuZgQHw51AJhkOnYDrMKisifFC0ssvxkh+nvwyTm
1w4R
=1YzJ
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2020.10-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
First set of u-boot-atmel features for 2020.10 cycle
Migrate the ST Microelectronics STUSB160X Type-C controller code in
a generic I2C driver in st/common, based on Linux one in :
drivers/usb/typec/stusb160x.c
This patch simplifies the stm32mp1 board code and allows to reuse
this STUSB160X driver in other boards.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Activate the command env erase to reset the environment with the command:
> env erase
it is simpler than:
> env default -a
> env save
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
As kernel v5.6 have a solution since so we will be able to enable
the watchdog at boot time. It is reloaded by the watchdog
framework (if CONFIG_WATCHDOG_HANDLE_BOOT_ENABLED is set) and
until the userspace watchdog daemon takes over control.
Need presence of kernel patch 85fdc63fe256 ("drivers: watchdog:
stm32_iwdg: set WDOG_HW_RUNNING at probe") integrated in v5.6-rc1.
This patch revert the previous commit ca351e705a ("stm32mp1:
deactivate WATCHDOG in defconfig").
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
This patch activates the new configuration CONFIG_GPIO_HOG.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add a function stmpic_init to early initialize the PMIC STPMIC1
- keep vdd on during the reset cycle (to avoid issue when backup battery
is absent)
- Check if debug is enabled to program PMIC according to the bit
This patch allows to remove the compilation of spl.c file from stm32mp1
board in dh_stm32mp1.
CONFIG_SPL_BOARD_INIT is removed as the new function is called earlier
in SPL, in the function board_early_init_f.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Rock Pi N8 is a Rockchip RK3288 based SBC, which has
- VMARC RK3288 SOM (as per SMARC standard) from Vamrs.
- Compatible carrier board from Radxa.
VAMRC RK3288 SOM need to mount on top of radxa dalang
carrier board for making Rock Pi N8 SBC.
So, add initial support for Rock Pi N8 by including rk3288,
rk3288 vamrc-som and raxda dalang carrier board dtsi files.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Rock Pi N10 is a Rockchip RK3399Pro based SBC, which has
- VMARC RK3399Pro SOM (as per SMARC standard) from Vamrs.
- Compatible carrier board from Radxa.
VAMRC RK3399Pro SOM need to mount on top of radxa dalang
carrier board for making Rock Pi N10 SBC.
So, add initial support for Rock Pi N10 by including rk3399,
rk3399pro vamrc-som and raxda dalang carrier board dtsi files.
rk3399pro-rock-pi-n10.dts was synced from linux-next v5.7-rc1.
Tested
- ROCK PI N10 Model B
- ROCK PI N10 Model C
- Boot from SD
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Some minor fixes for SPI flash on the Pinebook Pro and also
default to saving environment to the SPI flash as it's
guaranteed to be on board.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
(applied with make savedefconfig)
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The built in keyboard on the Pinebook Pro is attached via USB so
fix this up to ensure USB works as expected.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable the rng so UEFI can provide entropy for KASLR
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
With video output enabled and USB keyboard supported there is no need
for serial console. So let initialize USB subsystem so keyboard connected to
board (either directly or via hub) can be used to interrupt autoboot.
U-Boot TPL 2020.07-rc3-00123-g52d6cbd1a7 (Jun 03 2020 - 17:34:20)
Channel 0: LPDDR4, 50MHz
BW=32 Col=10 Bk=8 CS0 Row=16/15 CS=1 Die BW=16 Size=2048MB
Channel 1: LPDDR4, 50MHz
BW=32 Col=10 Bk=8 CS0 Row=16/15 CS=1 Die BW=16 Size=2048MB
256B stride
256B stride
lpddr4_set_rate: change freq to 400000000 mhz 0, 1
lpddr4_set_rate: change freq to 800000000 mhz 1, 0
Trying to boot from BOOTROM
Returning to boot ROM...
U-Boot SPL 2020.07-rc3-00123-g52d6cbd1a7 (Jun 03 2020 - 17:34:20 +0200)
Trying to boot from SPI
U-Boot 2020.07-rc3-00123-g52d6cbd1a7 (Jun 03 2020 - 17:34:20 +0200)
SoC: Rockchip rk3399
Reset cause: RST
Model: Pine64 RockPro64 v2.1
DRAM: 3.9 GiB
PMIC: RK808
MMC: mmc@fe310000: 2, mmc@fe320000: 1, sdhci@fe330000: 0
Loading Environment from SPI Flash... SF: Detected gd25q128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB
OK
In: serial
Out: vidconsole
Err: vidconsole
Model: Pine64 RockPro64 v2.1
Net: eth0: ethernet@fe300000
starting USB...
Bus usb@fe380000: USB EHCI 1.00
Bus usb@fe3a0000: USB OHCI 1.0
Bus usb@fe3c0000: USB EHCI 1.00
Bus usb@fe3e0000: USB OHCI 1.0
Bus dwc3: Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
Bus dwc3: Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus usb@fe380000 for devices... 1 USB Device(s) found
scanning bus usb@fe3a0000 for devices... 1 USB Device(s) found
scanning bus usb@fe3c0000 for devices... 1 USB Device(s) found
scanning bus usb@fe3e0000 for devices... 2 USB Device(s) found
scanning bus dwc3 for devices... 1 USB Device(s) found
scanning bus dwc3 for devices... 2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
Hit any key to stop autoboot: 0
=>
Signed-off-by: Marcin Juszkiewicz <marcin@juszkiewicz.com.pl>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
- Resync Kconfiglib with the v14.1.0 release.
- Re-sync our <linux/compiler*h> files with v5.7-rc5 from upstream.
- Fully resync checkpatch.pl with v5.7 release.
To safely to all of the above, we have a few bugfixes about functions
that need a 'static inline' but weren't. We also stop setting
CROSS_COMPILE in arch/*/config.mk. Finally, with the above changes
boards can now opt-in to optimizing inlining and we do this for the
socfpga stratix10 platform for space savings.
currently gpio hog function is not tested with "ut dm gpio"
so add some basic tests for gpio hog functionality.
For this enable GPIO_HOG in sandbox_defconfig, add
in DTS some gpio hog entries, and add testcase in
"ut dm gpio" command.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Starting from OpenSBI v0.7, the SBI firmware inserts/fixes up the
reserved memory node for PMP protected memory regions. All RISC-V
boards need to copy the reserved memory node from the device tree
provided by the firmware to the device tree used by U-Boot.
Turn on CONFIG_OF_BOARD_FIXUP by default for OF_SEPARATE.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Enable the new CONFIG_OPTIMIZE_INLINING and CONFIG_SPL_OPTIMIZE_INLINING
options for this platform. With gcc-9.2 from kernel.org this saves us
1784 bytes in U-Boot and 80 bytes in SPL.
Cc: Marek Vasut <marex@denx.de>
Cc: Chin-Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinh.nguyen@intel.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Marek Vasut <marex@denx.de>
The Sipeed Maix series is a collection of boards built around the RISC-V
Kendryte K210 processor. This processor contains several peripherals to
accelerate neural network processing and other "ai" tasks. This includes a
"KPU" neural network processor, an audio processor supporting beamforming
reception, and a digital video port supporting capture and output at VGA
resolution. Other peripherals include 8M of sram (accessible with and
without caching); remappable pins, including 40 GPIOs; AES, FFT, and SHA256
accelerators; a DMA controller; and I2C, I2S, and SPI controllers. Maix
peripherals vary, but include spi flash; on-board usb-serial bridges; ports
for cameras, displays, and sd cards; and ESP32 chips. Currently, only the
Sipeed Maix Bit V2.0 (bitm) is supported, but the boards are fairly
similar.
Documentation for Maix boards is located at
<http://dl.sipeed.com/MAIX/HDK/>. Documentation for the Kendryte K210 is
located at <https://kendryte.com/downloads/>. However, hardware details are
rather lacking, so most technical reference has been taken from the
standalone sdk located at
<https://github.com/kendryte/kendryte-standalone-sdk>.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
This patch adds a generic reset driver. It is designed to be useful when
one has a register in a regmap which contains bits that reset other
devices. I thought this seemed like a very generic use, so here is a
generic driver. The overall structure has been modeled on the syscon-reboot
driver.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This type of bus is used in Linux to designate buses which have power
domains and/or clocks which need to be enabled before their child devices
can be used. Because power domains are automatically enabled before probing
in U-Boot, we just need to enable any clocks present.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- Minor updates to some platforms I am the listed maintainer of.
Notably this removes the ti814x_evm which stopped building with the PXA
MMC migration series (oops) but hasn't been functional in some time.
The TI814x (DM814x) platform is rather old and in need of a lot of
migration work. As much of that work is well past the deadline, remove
this platform.
Signed-off-by: Tom Rini <trini@konsulko.com>
This platform is already using DM in general and the MMC controller is
the early generation of what is compatible with "ti,omap4-hsmmc" so
enable DM_MMC (which in turn gets BLK enabled).
Signed-off-by: Tom Rini <trini@konsulko.com>
- Makefile: add rule to build an endian-swapped U-Boot image
used by MIPS Malta EL variants
- CI: add Qemu tests for MIPS Malta
-----BEGIN PGP SIGNATURE-----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=dnTK
-----END PGP SIGNATURE-----
Merge tag 'mips-pull-2020-06-29' of https://gitlab.denx.de/u-boot/custodians/u-boot-mips into next
- net: pcnet: cleanup and add DM support
- Makefile: add rule to build an endian-swapped U-Boot image
used by MIPS Malta EL variants
- CI: add Qemu tests for MIPS Malta
The Qemu Malta machine expects the firmware in Big-Endian byte order.
Therefore the Little-Endian variants of the Malta board needs to
be byte swapped.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Add Kconfig entries for the pcnet driver and convert MIPS malta
to use those.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
This change allows more fine tuning of driver model based SPI support in
SPL and TPL. It is now possible to explicitly enable/disable the DM_SPI
support in SPL and TPL via Kconfig option.
Before this change it was necessary to use:
/* SPI Flash Configs */
#if defined(CONFIG_SPL_BUILD)
#undef CONFIG_DM_SPI
#undef CONFIG_DM_SPI_FLASH
#undef CONFIG_SPI_FLASH_MTD
#endif
in the ./include/configs/<board>.h, which is error prone and shall be
avoided when we strive to switch to Kconfig.
The goal of this patch:
Provide distinction for DM_SPI support in both U-Boot proper and SPL (TPL).
Valid use case is when U-Boot proper wants to use DM_SPI, but SPL must
still support non DM driver.
Another use case is the conversion of non DM/DTS SPI driver to support
DM/DTS. When such driver needs to work in both SPL and U-Boot proper, the
distinction is needed in Kconfig (also if SPL version of the driver
supports OF_PLATDATA).
In the end of the day one would have to support following use cases (in
single driver file - e.g. mxs_spi.c):
- U-Boot proper driver supporting DT/DTS
- U-Boot proper driver without DT/DTS support (deprecated)
- SPL driver without DT/DTS support
- SPL (and TPL) driver with DT/DTS (when the SoC has enough resources to
run full blown DT/DTS)
- SPL driver with DT/DTS and SPL_OF_PLATDATA (when one have constrained
environment with no fitImage and OF_LIBFDT support).
Some boards do require SPI support (with DM) in SPL (TPL) and some only
have DM_SPI{_FLASH} defined to allow compiling SPL.
This patch converts #ifdef CONFIG_DM_SPI* to #if CONFIG_IS_ENABLED(DM_SPI)
and provides corresponding defines in Kconfig.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Adam Ford <aford173@gmail.com> #da850-evm
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[trini: Fixup a few platforms]
Signed-off-by: Tom Rini <trini@konsulko.com>
Due to how the Makefile logic is we currently get DM_SPI support in SPL
enabled by having DM_SPI enabled for full U-Boot but not having
CONFIG_SPL_DM_SPI set. Add this missing option to boards that were
inadvertently making use of it.
Cc: Adam Ford <aford173@gmail.com>
Cc: Akash Gajjar <akash@openedev.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Andy Yan <andy.yan@rock-chips.com>
Cc: Anup Patel <anup.patel@wdc.com>
Cc: Atish Patra <atish.patra@wdc.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Chee Hong Ang <chee.hong.ang@intel.com>
Cc: Chin-Liang See <clsee@altera.com>
Cc: Dalon Westergreen <dwesterg@gmail.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Klaus Goger <klaus.goger@theobroma-systems.com>
Cc: Levin Du <djw@t-chip.com.cn>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Luca Ceresoli <luca@lucaceresoli.net>
Cc: Marek Vasut <marex@denx.de>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Mike Looijmans <mike.looijmans@topic.nl>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Peter Robinson <pbrobinson@gmail.com>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefan Roese <sr@denx.de>
Cc: Suniel Mahesh <sunil@amarulasolutions.com>
Cc: Vitaly Andrianov <vitalya@ti.com>
Cc: Wolfgang Grandegger <wg@aries-embedded.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
This converts the following to Kconfig:
CONFIG_CONSOLE_MUX
Cc: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
This converts the following to Kconfig:
CONFIG_BOOTCOUNT_ENV
CONFIG_BOOTCOUNT_LIMIT
Cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_AUTOBOOT_PROMPT
CONFIG_AUTOBOOT_KEYED
CONFIG_AUTOBOOT_STOP_STR
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_ATMEL_NAND_HW_PMECC
CONFIG_ATMEL_NAND_HWECC
CONFIG_NAND_ATMEL
CONFIG_PMECC_CAP
CONFIG_PMECC_SECTOR_SIZE
Signed-off-by: Tom Rini <trini@konsulko.com>
This board is very close to its limit. Drop this command before the bd
refactoring, which increases the size slightly on one toolchain.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Versal:
- xspi bootmode fix
- Removing one clock from clk driver
- Align u-boot memory setting with OS by default
- Map TCM and OCM by default
ZynqMP:
- Minor DT improvements
- Reduce console buffer for mini configurations
- Add fix for AMS
- Add support for XDP platform
Zynq:
- Support for AES engine
- Enable bigger memory test by default
- Extend documentation for SD preparation
- Use different freq for Topic miami board
mmc:
- minor GD pointer removal
net:
- Support fixed-link cases by zynq gem
- Fix phy looking loop in axi enet driver
spi:
- Cleanup global macros for xilinx spi drivers
firmware:
- Add support for pmufw reloading
fpga:
- Improve error status reporting
common:
- Remove 4kB addition space for FDT allocation
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCXvScEQAKCRDKSWXLKUoM
IeHUAJ9Z1shAlbILuHZKEpqQySLHdUVgBQCff8Nf+wi1rByTrwflKt14MtIsdFY=
=2Yuu
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2020.10' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2020.10
Versal:
- xspi bootmode fix
- Removing one clock from clk driver
- Align u-boot memory setting with OS by default
- Map TCM and OCM by default
ZynqMP:
- Minor DT improvements
- Reduce console buffer for mini configurations
- Add fix for AMS
- Add support for XDP platform
Zynq:
- Support for AES engine
- Enable bigger memory test by default
- Extend documentation for SD preparation
- Use different freq for Topic miami board
mmc:
- minor GD pointer removal
net:
- Support fixed-link cases by zynq gem
- Fix phy looking loop in axi enet driver
spi:
- Cleanup global macros for xilinx spi drivers
firmware:
- Add support for pmufw reloading
fpga:
- Improve error status reporting
common:
- Remove 4kB addition space for FDT allocation
XDP - Xilinx Drone Platform is a board for drones or other UAV.
Pinmux the SD card by default, and if the SD card detect line is high
(inactive) then pinmux the SD1 interface to EMIO instead. SD is placed on
extension card and shares connection with on board wife. That means that
when SD card is present in the board wifi can't be used.
There seems to be an issue with DDR access from PL at 2400MT/s, after
updating the PMU and ATF firmware this is causing extremely slow DDR
access. Reducing the DDR speed from 2400 to 2133 appears to solve that
issue, even though the hardware has proven to be 2400 capable.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enable alternative memory test for zynq platforms.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is no reason not to let U-Boot to update memory node by default. In
past this was disabled by purpose to be able to test different memory
configurations from one U-Boot instance.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
In order to take the beneficts of DT and DM in SPL, like reusing the code
and avoid redundancy, enable SPL_OF_CONTROL, SPL_DM and SPL_DM_MMC.
With this new configuration SPL image is 50 KB, higher than the
38 KB from the previous version, but it still under the 68 KB limit.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
We need to change the environment offset to avoid corrupting the U-Boot
binary when saving it.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
This fixes the boot from USB loader, which is critical to easy the
manufacture process.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Select default U-Boot and SPL text base for the MX7 SoC. The U-Boot
text base is picked as the one used by various MX7 boards. The SPL
text base however is different.
The SPL text base is set to 0x912000 instead of the usual 0x911000,
that is because the 0x911000 value cannot work. Using 0x911000 as a
SPL text base will result in the DCD header being placed below the
0x911000 address, which is a reserved SRAM area which must not be
used. This will actually trigger eMMC boot failure on MX7D at least.
Hence the increment.
Update all boards affected by this SPL problem to the new SPL_TEXT_BASE.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
For using a debug UART on the Wandboard CONFIG_MXC_UART=y must be set in
the .config file.
To avoid duplicate definitions move the setting from
include/configs/wandboard.h to configs/wandboard_defconfig.
Document the debug UART settings in the README.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
It appears that MMC access on the Sabrelite has been broken since
cdcaee9518:
Loading Environment from MMC... Card did not respond to voltage select!
*** Warning - No block device, using default environment
Remove the board_mmc_init() and related entries now that we should be
using DM_MMC, add PINCTRL so that things work as expected.
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Troy Kisky <troy.kisky@boundarydevices.com>
This introduces automatic boot counter that increases after every
reset.After a power-on reset, it will be initialized with 1,
and each reboot will increment the value by 1. By default it's
disabled if bootlimit isn't set.
To enable this feature you have set bootcount limit ("bootlimit"),
alternate boot action ("altbootcmd") that will be performed if
the new value of bootcount exceeds the value of bootlimit, and
"upgrade_available" to let U-Boot automatically increase and save
the counter value after every reset:
> setenv bootlimit 5
> setenv upgrade_available 1
> setenv altbootcmd "bootm ..."
In case the bootlimit exceeds, the message will be shown and
albootcmd executed:
Warning: Bootlimit (5) exceeded. Using altbootcmd.
To reset bootcount run:
> bootcount reset
Print current value:
> bootcount print
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
s/fdt-module/fdt_module/g, as we don't use dash in fdt_file anymore.
Fixes: 4c63a601("apalis-tk1: support v1.2 hardware revision")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
1. Use distro_bootcmd as default boot command instead of
legacy emmcboot wrapper.
2. Drop emmcboot and sdboot wrappers.
3. Provide proper boot order for Distro Boot.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
This got dropped by a global 'make savedefconfig' resync as
required patches are still in flight.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Migration to DM_ETH is mandatory, so convert mx6cuboxi to Ethernet
Driver Model.
This also brings the benefit of restoring Ethernet functionality.
Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Tom Rini <trini@konsulko.com>
This allows Nano to use the key M.2 on the CVB to connect and use a M.2
NVMe SSD stick. Works on my Nano B00, WD SN750 NVMe SSD shows up
w/'nvme' commands. Will add booting from NVMe via distro cmds in a future
patch.
Signed-off-by: Tom Warren <twarren@nvidia.com>
- use 'vidconsole' stdout in nitrogen6x upgrade script
- add option for selection of the vidconsole commands
lcdputs and setcurs
- allow building ipuv3 driver with disabled CONFIG_PANEL
- make backlight and panel drivers optional
- remove useless code from ipuv3 driver
- extend existing DM_VIDEO work-around for console name
to support 'vga'
- remove non-DM code in ipuv3
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCXuvRkA4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXMpeAJkB/FzsJ3O7putHrbLKOrLRF3zZYwCfQxa9jKuh
DXNTYVrHS/43T8ijGYo=
=7G75
-----END PGP SIGNATURE-----
Merge tag 'video-next' of https://gitlab.denx.de/u-boot/custodians/u-boot-video into next
- migrate remaining imx5/imx6qd boards to DM_VIDEO
- use 'vidconsole' stdout in nitrogen6x upgrade script
- add option for selection of the vidconsole commands
lcdputs and setcurs
- allow building ipuv3 driver with disabled CONFIG_PANEL
- make backlight and panel drivers optional
- remove useless code from ipuv3 driver
- extend existing DM_VIDEO work-around for console name
to support 'vga'
- remove non-DM code in ipuv3
Migration to DM_VIDEO driver is long overdue. Update defconfig
to enable usage of converted ipuv3 driver DM configuration.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Jason Liu <jason.hui.liu@nxp.com>
Acked-by: Jason Liu<jason.hui.liu@nxp.com>
Migration to DM_VIDEO driver is long overdue. Update defconfigs
to enable usage of converted ipuv3 driver DM configuration.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Migration to DM_VIDEO driver is long overdue. Update defconfig
to enable usage of converted ipuv3 driver DM configuration.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Migration to DM_VIDEO driver is long overdue. Update defconfigs
to enable usage of converted ipuv3 driver DM configuration.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Akshay Bhat <akshaybhat@timesys.com>
Cc: Ken Lin <Ken.Lin@advantech.com.tw>
Migration to DM_VIDEO driver is long overdue. Update defconfigs
to enable usage of converted ipuv3 driver DM configuration.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Eric Bénard <eric@eukrea.com>
Add Kconfig entries for the pcnet driver and convert MIPS malta
to use those.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Migration to DM_VIDEO driver is long overdue, configure it in
board config files. To enable the display set stdout like:
setenv stdout serial,vidconsole
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Soeren Moch <smoch@web.de>
Enable driver model for Video to remove compiler warning.
To enable display, issue
setenv stdout serial,vidconsole;
Add CONFIG_DM_VIDEO to all defconfigs whose board is
nitrogen6x.
mx6qsabrelite_defconfig
nitrogen6dl2g_defconfig
nitrogen6dl_defconfig
nitrogen6q2g_defconfig
nitrogen6q_defconfig
nitrogen6s1g_defconfig
nitrogen6s_defconfig
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Tested-by: Anatolij Gustschin <agust@denx.de>
Enable DM_SPI for am355x baltos board.
Build is fine, but not tested.
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Yegor Yefremov <yegorslists@googlemail.com>
DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Patch-cc: Xiaobo Xie <xiaobo.xie@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Patch-cc: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Patch-cc: Poonam Aggrwal <poonam.aggrwal@nxp.com>
Patch-cc: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Patch-cc: Timur Tabi <timur@tabi.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Patch-cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Patch-cc: Po Liu <po.liu@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Patch-cc: Naveen Burmi <naveen.burmi@nxp.com>
Patch-cc: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Patch-cc: Poonam Aggrwal <poonam.aggrwal@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Patch-cc: Ashish Kumar <ashish.kumar@nxp.com>
Patch-cc: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Now that CONFIG_SPL_SEPARATE_BSS is selected for all the AT91 based
boards, cleanups the defconfigs by removing it.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The da850evm boots from SPI flash while the da850evm_nand_defconfig
boots from NAND and these are configs are mutually exclusive.
Since there isn't a need for SPI during SPL in the NAND configuration,
this patch removes the SPI drivers in SPL while making them still
available in U-Boot proper. This should save some code space in SPL.
Signed-off-by: Adam Ford <aford173@gmail.com>
Cleanup this driver to use dt in U-boot and static platdata in SPL.
This requires the following steps:
1. Move all platdata assignment from probe() to ofdata_to_platdata().
This function is only called in U-boot.
2. Replicate all the platdata assignment being done in
ofdata_to_platdata() in the omapl138 board file. This data is used in
the SPL case where SPL_OF_CONTROL is not enabled.
3. Remove SPL_OF_CONTROL and related configs from omapl138_lcdk_defconfig
This cleanup effectively reverts 3ef94715cc ('mmc: davinci: fix mmc boot in SPL')
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
change to how sequence numbers are assigned to devices
minor fixes and improvements
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl7kQ4kRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreZrvAgAqc/TEj7QHPyW9rQSl8h65MXK93qRsnZo
4segKEtK0Rmv0S2VfmPCwujsDFl5gZUNt+rXD/l7F0a4Wzx4eYgYrEXOYsXs/ZHP
jjGrcbvO4Qkx3QzjMqqoUiQqeCgNQ9XIre8F+1NmZeQ2bFtPKbJXtXKYTcMI1wSW
PhRGbbsTnKNKC0dL0nLFG6+NC/sk6xRqMx28Ip38FTrQL+Uh67LZFpLkY3yuHo/1
CVhCw+7Aov0I6tDrdKrngjFqXRSoTsuOhavSFoW9U6llqDL7FIC6aoRo7x24lSJN
VFTRpXPmNHeslE6NHEOQs9elFpbxXR34te3k4p74rFuX/J/490UaYA==
=172C
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-12jun20' of git://git.denx.de/u-boot-dm into next
patman improvements to allow it to work with Zephyr
change to how sequence numbers are assigned to devices
minor fixes and improvements
ti_phy_init function was allocated to the DP83867 PHY. This function
name is to generic for a specific PHY. The function can be moved to a
TI specific file that can register all TI PHYs that are defined in the
defconfig. The ti_phy_init file will contain all TI PHYs initialization
so that only phy_ti_init can be called from the framework.
In addition to the above the config flag for the DP83867 needs to be changed
in the Kconfig and dependent defconfig files. The config flag that was
used for the DP83867 was also generic in nature so a more specific
config flag for the DP83867 was created.
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
This keeps the compatibility with the old bootcmd.
The fdtfile environment variable also needed to be set to
imx6q-tbs2910.dtb to enable booting mainline kernels
otherwise with extlinux.conf it tries to load
mx6-tbs2910.dtb instead.
With arm-linux-gnueabi-gcc 9.2.0-1 from the Parabola
GNU/Linux distribution, we have the following size
differences:
- text: +2041 bytes
- data: 0 bytes
- bss: 0 bytes
- total: +2041 bytes
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@cyberdimension.org>
Reviewed-by: Soeren Moch <smoch@web.de>
This is needed to enable distro_boot support later on.
Adding the necessary configuration to enable booting general
purpose distributions is typically done by enabling
CONFIG_DISTRO_DEFAULTS.
However the resulting image size is is already very close to
the size limit and PXE isn't strictly needed, so instead we
made sure that all the configuration selected by
CONFIG_DISTRO_DEFAULTS were selected, with the exception of
PXE related configuration (CONFIG_BOOTP_PXE and
CONFIG_CMD_PXE) that are both disabled.
With arm-linux-gnueabi-gcc 9.3.0-1 from the Parabola
GNU/Linux distribution, we have the following size
differences:
- text: +7526 bytes
- data: +28 bytes
- bss: -12 bytes
- total: +7542 bytes
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@cyberdimension.org>
Reviewed-by: Soeren Moch <smoch@web.de>
This doesn't affect the size of the image: with
arm-linux-gnueabi-gcc 9.2.0-1 from the Parabola GNU/Linux
distribution, the text, data, bss and total sizes remain
unchanged.
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@cyberdimension.org>
Reviewed-by: Soeren Moch <smoch@web.de>
As that the resulting image is already very close to the
size limit, and that CONFIG_GZIP is not strictly required,
removing it shouldn't hurt.
With arm-linux-gnueabi-gcc 9.2.0-1 from the Parabola
GNU/Linux distribution we have the following size
reduction:
- text: 9752
- data: 0
- bss: 16
- total: 9768
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@cyberdimension.org>
Acked-by: Soeren Moch <smoch@web.de>
The loadb and loads commands are not needed for booting.
There are also more reliable and faster alternatives to
loadb and loads that can be used with the current configuration.
As that the resulting image is already very close to the
size limit, removing the loadb and loads commands shouldn't
hurt.
With arm-linux-gnueabi-gcc 9.2.0-1 from the Parabola
GNU/Linux distribution we have the following size
reduction:
- text: 6733 bytes
- data: 116 bytes
- bss: 1172 bytes
- total: 8021 bytes
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@cyberdimension.org>
Acked-by: Soeren Moch <smoch@web.de>
Enable DM_SPI for am355x sl50 board.
Build is fine, but not tested.
Cc: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Enable DM_SPI for igep00x0 board.
Build is fine, but not tested.
Cc: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
OF_CONTROL, DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Acked-by: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
OF_CONTROL, DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Acked-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
This would make SPL build to DM_SPL, SPL_OF_CONTROL.
Build fine with but not tested.
Cc: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Convert the board to DM_ETH instead of legacy networking. This requires
a minor addition to the DT to satisfy the requirement for specifying a
PHY node. No functional change from board user perspective.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
The u-boot-spl.bin pad with ddr firmware conflicts with the
CONFIG_MALLOC_F_ADDR area, the ddr firmware will be overwritten
by malloc in SPL stage and cause ddr initialization not able
to finish. So update the related addresses to fix the issue.
Reported-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Currently watchdog driver is not selected, which causes system to reboot
after staying 60s in the U-Boot prompt.
Fix this problem by enabling CONFIG_WATCHDOG so that watchdog can be
properly serviced.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Currently watchdog driver is not selected, which causes system to reboot
after staying 60s in the U-Boot prompt.
Fix this problem by enabling CONFIG_WATCHDOG so that watchdog can be
properly serviced.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Currently watchdog driver is not selected, which causes system to reboot
after staying 60s in the U-Boot prompt.
Fix this problem by enabling CONFIG_WATCHDOG so that watchdog can be
properly serviced.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Adam Ford <aford173@gmail.com>
Currently watchdog driver is not selected, which causes system to reboot
after staying 60s in the U-Boot prompt.
Fix this problem by enabling CONFIG_WATCHDOG so that watchdog can be
properly serviced.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Currently the watchdog driver is not selected, which causes the following
warnings in both SPL and U-Boot proper:
U-Boot SPL 2020.07-rc1-00387-g67887903af (May 07 2020 - 23:49:27 -0300)
Normal Boot
WDT: Started without servicing (60s timeout)
Trying to boot from MMC1
U-Boot 2020.07-rc1-00387-g67887903af (May 07 2020 - 23:49:27 -0300)
CPU: Freescale i.MX8MMQ rev1.0 at 1200 MHz
Reset cause: POR
Model: FSL i.MX8MM EVK board
DRAM: 2 GiB
WDT: Started without servicing (60s timeout)
....
System reboots after staying 60s in the U-Boot prompt.
Fix this problem by enabling CONFIG_WATCHDOG so that watchdog can be
properly serviced.
Suggested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Enable CONFIG_PCI and CONFIG_NVME and related configs for the
Pinebook Pro.
Signed-off-by: Patrick Wildt <patrick@blueri.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
With recently added changes we get support for usb3 including handling
of the phys (type-c and inno-usb2), so enable the necessary config
options on puma.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
