To support the Spansion SPI NOR flashes, this patch enables the support in
defconfig. This increases the U-Boot binary too much so that it does
not fit into its area in the ROM. So also move the VIDEO BIOS blob
a bit to make some space here.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add Intel Edison board which is using U-Boot.
The patch is based on work done by the following people (in alphabetical
order):
Aiden Park <aiden.park@intel.com>
Dukjoon Jeon <dukjoon.jeon@intel.com>
eric.park <eric.park@intel.com>
Fabien Chereau <fabien.chereau@intel.com>
Felipe Balbi <felipe.balbi@linux.intel.com>
Scott D Phillips <scott.d.phillips@intel.com>
Sebastien Colleur <sebastienx.colleur@intel.com>
Steve Sakoman <steve.sakoman@intel.com>
Vincent Tinelli <vincent.tinelli@intel.com>
In case we're building for Intel Edison, we must have 4096 bytes of
zeroes in the beginning on u-boot.bin. This is done in
board/intel/edison/config.mk.
First run sets hardware_id environment variable which is read from
System Controller Unit (SCU).
Serial number (serial# environment variable) is generated based on eMMC
CID.
MAC address on USB network interface is unique to the board but kept the
same all over the time.
Set mac address from U-Boot using following scheme:
OUI = 02:00:86
next 3 bytes of MAC address set from eMMC serial number
This allows to have a unique mac address across reboot and flashing.
Signed-off-by: Vincent Tinelli <vincent.tinelli@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[bmeng: Add MAINTAINERS file for Intel Edison board]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Kbuild complains if USB is not selected before any of host driver.
warning: (X86) selects USB_EHCI_HCD which has unmet direct dependencies (USB)
warning: (X86) selects USB_EHCI_HCD which has unmet direct dependencies (USB)
Select it for X86.
Fixes: 64d6ac5bc4 ("Kconfig: USB: Migrate CONFIG_USB_EHCI_HCD users to Kconfig")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[bmeng: Update all x86 boards' defconfig files to remove CONFIG_USB]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
BayTrail SoC supports both EHCI and xHCI controllers. However only
one host controller (either EHCI or xHCI) can be used. To enable
HSIC and SS ports, xHCI must be used. This turns on xHCI support on
Intel MinnowMax board.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Change these board to use a live device tree after relocation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Beaver, Jetson-TK1
Tested-by: Stephen Warren <swarren@nvidia.com>
Convert this PMIC driver to driver model and fix up other users. The
regulator and GPIO functions are now handled by separate drivers.
Update nyan-big to work correct. Three boards will need to be updated by
the maintainers: apalis-tk1, cei-tk1-som. Also the TODO in the code re
as3722_sd_set_voltage() needs to be completed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Jetson-TK1
Tested-by: Stephen Warren <swarren@nvidia.com>
function board_init_f_init_reserve will call memset, which
is implemented in lib, and enabled by CONFIG_SPL_LIBGENERIC_SUPPORT
in spl stage.
To reduce the code size, also enable SPL_TINY_MEMSET.
As rk3036 will return to bootrom immediately after dram
initialization, there is no need to run DM, so disable
SPL_DM_SERIAL.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
RK3036 has no enough sapce use ARCH_MEMCPY/MEMSET in spl stage
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
RK3036 only has 4kb sram, the spl code will use
3.4 ~ 3.5 kb, the last 0.5kb are used for SP and
GD, so there is no space for malloc. Also, the spl
will directly return to bootrom after dram initialized,
they never need the space for malloc.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add four macros of CONFIG_USB_KEYBOARD,CONFIG_DM_KEYBOARD,etc in the
firefly-rk3288_defconfig,can support usb keyboard device when these four
macros are enabled.
Signed-off-by: Leo Wen <leo.wen@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
GPIOs are now supported on Meson GXBB, enable driver and command in
the config.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
It has been a while since ARM Trusted Firmware supported UniPhier SoC
family. U-Boot SPL was intended as a temporary loader that runs in
secure world. It is a maintenance headache to support two different
boot mechanisms. Secure firmware is realm of ARM Trusted Firmware
and now U-Boot only serves as a non-secure boot loader for UniPhier
ARMv8 SoCs.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This converts the following to Kconfig:
CONFIG_FPGA_SOCFPGA
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Dinh Nguyen <dinguyen@kernel.org>
This converts the following to Kconfig:
CONFIG_FPGA
CONFIG_FPGA_ALTERA
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Dinh Nguyen <dinguyen@kernel.org>
This converts the following to Kconfig:
CONFIG_ENV_IS_IN_MMC
CONFIG_ENV_IS_IN_NAND
CONFIG_ENV_IS_IN_UBI
CONFIG_ENV_IS_NOWHERE
In fact this already exists for sunxi as a 'choice' config. However not
all the choices are available in Kconfig yet so we cannot use that. It
would lead to more than one option being set.
In addition, one purpose of this series is to allow the environment to be
stored in more than one place. So the existing choice is converted to a
normal config allowing each option to be set independently.
There are not many opportunities for Kconfig updates to reduce the size of
this patch. This was tested with
./tools/moveconfig.py -i CONFIG_ENV_IS_IN_MMC
And then manual updates. This is because for CHAIN_OF_TRUST boards they
can only have ENV_IS_NOWHERE set, so we enforce that via Kconfig logic
now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
The above CONFIG options are in Kconfig, and now have correct depends and
inter-dependencies. Migrate these to configs/ from include/configs/. In the
case of CMD_UBIFS also change it to be a default y if CMD_UBI.
Signed-off-by: Tom Rini <trini@konsulko.com>
Move CONFIG_CMD_SATA option to Kconfig to fix the following build
error:
In file included from include/configs/mx6cuboxi.h:137:0,
from include/config.h:7,
from include/common.h:21,
from common/env_common.c:11:
include/config_distro_bootcmd.h:161:2: error: expected '}' before 'BOOT_TARGET_DEVICES_references_SATA_without_CONFIG_SATA'
BOOT_TARGET_DEVICES_references_SATA_without_CONFIG_SATA
Reported-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
warp can run different kernel versions, such as NXP 4.1 or
mainline.
Currently the rootfs location is passed via mmcblk number and the
problem with this approach is that the mmcblk number for the eMMC
changes depending on the kernel version.
In order to avoid such issue, use UUID method to specify the rootfs
location.
Succesfully tested booting a NXP 4.1 and also a mainline 4.12 kernel.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
mx6sabre boards can run different kernel versions, such as NXP 4.1 or
mainline.
Currently the rootfs location is passed via mmcblk number and the
problem with this approach is that the mmcblk number for the eMMC
changes depending on the kernel version.
In order to avoid such issue, use UUID method to specify the rootfs
location.
Succesfully tested booting a NXP 4.1 and also a mainline kernel on a
mx6qsabresd and mx6dlsabreauto.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
WEIM cannot be used when I2C3 is enabled due to pin conflict, so keep
WEIM disabled by default.
I2C3 controls GPIO I2C expander (USB host and OTG have VBUS controlled by
the GPIO I2C expander), magnetometer, accelerometer.
Not disabling WEIM in U-Boot causes I2C3 to behave badly when booting
a NXP 4.1 kernel, which leads to probe failure on several devices,
including the lack of USB:
imx_usb 2184000.usb: Can't register ci_hdrc platform device, err=-517
By keeping WEIM disabled in U-Boot these kernel issues are gone.
Reported-by: Takashi Matsuzawa <tmatsuzawa@xevo.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Change is consistent with other SOCs and it is in preparation
for adding SOMs. SOC's related files are moved from cpu/ to
mach-imx/<SOC>.
This change is also coherent with the structure in kernel.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@nxp.com>
CC: Akshay Bhat <akshaybhat@timesys.com>
CC: Ken Lin <Ken.Lin@advantech.com.tw>
CC: Marek Vasut <marek.vasut@gmail.com>
CC: Heiko Schocher <hs@denx.de>
CC: "Sébastien Szymanski" <sebastien.szymanski@armadeus.com>
CC: Christian Gmeiner <christian.gmeiner@gmail.com>
CC: Stefan Roese <sr@denx.de>
CC: Patrick Bruenn <p.bruenn@beckhoff.com>
CC: Troy Kisky <troy.kisky@boundarydevices.com>
CC: Nikita Kiryanov <nikita@compulab.co.il>
CC: Otavio Salvador <otavio@ossystems.com.br>
CC: "Eric Bénard" <eric@eukrea.com>
CC: Jagan Teki <jagan@amarulasolutions.com>
CC: Ye Li <ye.li@nxp.com>
CC: Peng Fan <peng.fan@nxp.com>
CC: Adrian Alonso <adrian.alonso@nxp.com>
CC: Alison Wang <b18965@freescale.com>
CC: Tim Harvey <tharvey@gateworks.com>
CC: Martin Donnelly <martin.donnelly@ge.com>
CC: Marcin Niestroj <m.niestroj@grinn-global.com>
CC: Lukasz Majewski <lukma@denx.de>
CC: Adam Ford <aford173@gmail.com>
CC: "Albert ARIBAUD (3ADEV)" <albert.aribaud@3adev.fr>
CC: Boris Brezillon <boris.brezillon@free-electrons.com>
CC: Soeren Moch <smoch@web.de>
CC: Richard Hu <richard.hu@technexion.com>
CC: Wig Cheng <wig.cheng@technexion.com>
CC: Vanessa Maegima <vanessa.maegima@nxp.com>
CC: Max Krummenacher <max.krummenacher@toradex.com>
CC: Stefan Agner <stefan.agner@toradex.com>
CC: Markus Niebel <Markus.Niebel@tq-group.com>
CC: Breno Lima <breno.lima@nxp.com>
CC: Francesco Montefoschi <francesco.montefoschi@udoo.org>
CC: Jaehoon Chung <jh80.chung@samsung.com>
CC: Scott Wood <oss@buserror.net>
CC: Joe Hershberger <joe.hershberger@ni.com>
CC: Anatolij Gustschin <agust@denx.de>
CC: Simon Glass <sjg@chromium.org>
CC: "Andrew F. Davis" <afd@ti.com>
CC: "Łukasz Majewski" <l.majewski@samsung.com>
CC: Patrice Chotard <patrice.chotard@st.com>
CC: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CC: Hans de Goede <hdegoede@redhat.com>
CC: Masahiro Yamada <yamada.masahiro@socionext.com>
CC: Stephen Warren <swarren@nvidia.com>
CC: Andre Przywara <andre.przywara@arm.com>
CC: "Álvaro Fernández Rojas" <noltari@gmail.com>
CC: York Sun <york.sun@nxp.com>
CC: Xiaoliang Yang <xiaoliang.yang@nxp.com>
CC: Chen-Yu Tsai <wens@csie.org>
CC: George McCollister <george.mccollister@gmail.com>
CC: Sven Ebenfeld <sven.ebenfeld@gmail.com>
CC: Filip Brozovic <fbrozovic@gmail.com>
CC: Petr Kulhavy <brain@jikos.cz>
CC: Eric Nelson <eric@nelint.com>
CC: Bai Ping <ping.bai@nxp.com>
CC: Anson Huang <Anson.Huang@nxp.com>
CC: Sanchayan Maity <maitysanchayan@gmail.com>
CC: Lokesh Vutla <lokeshvutla@ti.com>
CC: Patrick Delaunay <patrick.delaunay@st.com>
CC: Gary Bisson <gary.bisson@boundarydevices.com>
CC: Alexander Graf <agraf@suse.de>
CC: u-boot@lists.denx.de
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
As mx6sabreauto supports SPL now, all variants can boot using the same
defconfig.
This patch:
- Removes non-SPL targets.
- Renames target to mx6sabreauto_defconfig.
- Renames folder and board files to mx6sabreauto.
- Updates MAINTAINERS, Makefile and Kconfig accordingly.
- Removes .cfg files.
- Adds a README with instructions to build and flash SPL and u-boot.img.
Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Add support for mx6q, mx6dl and mx6qp sabreauto boards in SPL.
Retrieved the mx6q DCD table from:
board/freescale/mx6qsabreauto/imximage.cfg
Retrieved the mx6dl DCD table from:
board/freescale/mx6qsabreauto/mx6dl.cfg
Retrieved the mx6qp DCD table from:
board/freescale/mx6qsabreauto/mx6qp.cfg
Flashed SPL and u-boot.img to an SD card and could successfully boot it
on mx6q, mx6qp and mx6dl sabreauto boards.
Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
imx6qdl_icore_mmc_defconfig => imx6qdl_icore_rqs_defconfig
Since icorem6_rqs support MMC/eMMC boot, so doesn't need
to name it explicitly.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add support for the debug UART to assist with early debugging.
Enable it for i.CoreM6 as an example.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
SPL is already selected via CONFIG_SPL=y, so there is no need
to pass it inside CONFIG_SYS_EXTRA_OPTIONS.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
SPL is already selected via CONFIG_SPL=y, so there is no need
to pass it inside CONFIG_SYS_EXTRA_OPTIONS.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
SPL is already selected via CONFIG_SPL=y, so there is no need
to pass it inside CONFIG_SYS_EXTRA_OPTIONS.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
SPL is already selected via CONFIG_SPL=y, so there is no need
to pass it inside CONFIG_SYS_EXTRA_OPTIONS.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Currently, Marvell Armada8k development board use 3 different
defconfigs:
mvebu_db-88f7040-nand_defconfig
mvebu_db-88f7040_defconfig
mvebu_db-88f8040_defconfig
Having 3 different defconfigs makes maintenance difficult.
This patch removes the defconfigs mentioned above and introduce
a new defconfig which represents the Armada8k family.
NOTE:
In order not to break automatic tools compilation,
a default device-tree is set in the defconfig (armada-8040-db).
However, when compiling u-boot, the user MUST explicitly export
the DEVICE_TREE for the requested board because using A80x0
device-tree on A70x0 might break the device.
For more information, refer to "doc/README.marvell" (intoduced
in this patch).
Change-Id: I98515b6306498358f3722ecf7ac4c87f236ebbd8
Signed-off-by: Igal Liberman <igall@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The Turris Omnia is a open-source router created by CZ.NIC.
The code is based on the Marvell/db-88f6820-gp by Stefan Roese
with modifications from Tomas Hlavacek in the CZ.NIC turris-omnia-uboot
repository, which can be found at
https://gitlab.labs.nic.cz/turris/turris-omnia-uboot
By default, the Turris Omnia uses btrfs as the main and only filesystem,
and also loads kernel and device tree from this filesystem. Since U-Boot
does not yet support btrfs, you should not flash your Turris Omnia board
with this unless you know what you are doing.
Signed-off-by: Tomas Hlavacek <tomas.hlavacek@nic.cz>
Signed-off-by: Marek Behun <marek.behun@nic.cz>
create mode 100644 board/CZ.NIC/turris_omnia/Makefile
create mode 100644 board/CZ.NIC/turris_omnia/kwbimage.cfg
create mode 100644 board/CZ.NIC/turris_omnia/turris_omnia.c
create mode 100644 configs/turris_omnia_defconfig
create mode 100644 include/configs/turris_omnia.h
Signed-off-by: Stefan Roese <sr@denx.de>
When CONFIG_CMD_FASTBOOT or CONFIG_USB_FUNCTION_FASTBOOT are defined
in am335x_evm.h, a dependency on g_dnl.c is created. This in turn
creates a dependency on having USB gadget enabled.
As a result we can't create configs with USB gadget disabled.
Since these CONFIG_ variables are now part of kconfig, move them to
the board defconfigs, and out of am335x_evm.h. This both preserves
current defaults, and allows creating configs with USB gadget off.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The TI816x has 2 GPIO banks. For bank 0 we had been clearing the enable
bit when setting BIT(8). Correct this by setting it to BIT(1) | BIT(8)
after we set and wait for BIT(1) (aka PRCM_MOD_EN). Enable GPIO1 as
well so that when CMD_GPIO is enabled it won't crash probing the second
bank. Enable CMD_GPIO on ti816x_evm.
Signed-off-by: Tom Rini <trini@konsulko.com>
The ti816x SoC revision of the ethernet IP block is handled by the
"davinci_emac" driver, rather than the "cpsw" driver as done by later
members of the family. Enable the relevant plumbing.
Signed-off-by: Sriramakrishnan <srk@ti.com>
Signed-off-by: Vitaly Wool <vitaly.wool@konsulko.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Enable full bootstage support so we can time SPL and U-Boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Beaver, Jetson-TK1
Enable this to allow debugging when the serial UART driver is
misconfigured.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Beaver, Jetson-TK1
Enable the pre-console buffer, displaying the model and post-relocation
console announce on sandbox. Also add a model name to the device tree.
This allows testing of these features.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
As a demonstration of how to use SCSI with driver model, move link over
to use this. This patch needs more work, but illustrates the concept.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The phyCORE-RK3288 is a SoM (System on Module) containing a RK3288 SoC.
The module can be connected to different carrier boards.
It can be also equipped with different RAM, SPI flash and eMMC variants.
The Rapid Development Kit option is using the following setup:
- 1 GB DDR3 RAM (2 Banks)
- 1x 4 KB EEPROM
- DP83867 Gigabit Ethernet PHY
- 16 MB SPI Flash
- 4 GB eMMC Flash
Add basic support for the PCM-947 carrier board, a RK3288 based development
board made by PHYTEC. This board works in a combination with
the phyCORE-RK3288 System on Module.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The driver changes gpio to fixed regulator to control vbus, so add
fixed regulator node in DTS for xhci driver.
Signed-off-by: Meng Dongyang <daniel.meng@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This change migrates the USB_DWC2 configuration item to Kconfig
and runs moveconfig to adjust header files and defconfig.
Signed-off-by: Meng Dongyang <daniel.meng@rock-chips.com>
Split off into a separate patch:
Ran moveconfig to migrate other boards:
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
rk3036 sdram driver does not use DM, remove CONFIG_RAM first.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Enable mmc_dw_rockchip driver, disable CONFIG_SPL_OF_PLATDATA
first for some dependence patches still not merged.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
The rv1108 do not have DRAM driver now, so disable it first,
or else it will get conflict with the sdram common code.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This port adds support for:
1) Serial
2) eMMC
3) USB
It has been tested with ARM TRUSTED FIRMWARE running u-boot as the
BL33 executable [see board's README]
eMMC has been tested for reading and booting the loader and linux
kernels as well as saving the u-boot environment.
USB has been tested with ASIX networking adapter and SanDisk 7.4GB
drive.
PSCI has been tested via the reset call (PSCI executes from DDR)
The firwmare upgrade process has been tested via TFTP and USB FAT
filesystem containing the fastboot.bin image in one of the partitions.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Include K2G ICE to OF_LIST so it can be used for runtime board
detection.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable various config options to allow U-boot at runtime to select the
proper dtb to use from the list of dtb's within the FIT image.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
CS Systemes d'Information (CSSI) manufactures two boards, named MCR3000
and CMPC885 which are respectively based on MPC866 and MPC885 processors.
This patch adds support for the first board.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
On startup the SL50 board halt at U-Boot prompt. Use CONFIG_AUTOBOOT_KEYED
to enable autoboot for this board and define the <SPACE> key to get the
U-Boot prompt.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
AVR32 is gone. It's already more than two years for no support in Buildroot,
even longer there is no support in GCC (last version is heavily patched 4.2.4).
Linux kernel v4.12 got rid of it (and v4.11 didn't build successfully).
There is no good point to keep this support in U-Boot either.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The Odroid C2 comes with several expansion options such as an RTC module.
As these expansions are not considered in the Linux device tree they have
to be enabled via device tree overlays.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
CHIP and CHIP Pro devices have options of DIP addon boards some of which need
overlays from the beginning so it makes sense to enable device tree overlays.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
96boards CE devices such as the DragonBoard and Hikey devices have numerous
mezzanine options some of which need overlays from the beginning so it makes
sense to enable device tree overlays.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
TI am33xx devices such as the BeagleBone devices have numerous cape options such
as screens some of which need overlays from the beginning so it makes sense to
enable evice tree overlays.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Raspberry Pi has numerous HAT and other HW expansion options such as screens and
cameras some of which need overlays from the beginning so it makes sense to
enable evice tree overlays.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Fastmap significantly reduces flash scan time, enable it by default.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Heiko Schocher <hs@denx.de>
There was for long time no activity in the 4xx area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in 4xx,
so remove it.
Signed-off-by: Heiko Schocher <hs@denx.de>
Enable DFU and USB mass storage support for the DENX MA5D4 SoM.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
ARC HS Development Kit board is a new low-cost
development platform sporting ARC HS38 in real silicon
with nice set of features such as:
* Quad-core ARC HS38 with 512 kB L2 cache and running @1GHz
* 4Gb of DDR (we use only lowest 1Gb out of it now)
* Lots of DesigWare peripherals
* Different connectivity modules:
- Synopsys HAPS HT3
- Arduino-compatible connector
- MikroBUS
This initial commit supports the following peripherals:
* UART (DW 8250)
* Ethernet (DW GMAC)
* SD/MMC (DW Mobile Storage)
* USB 1.1 & 2.0
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
With eb5ba3aefd "i2c: Drop use of CONFIG_I2C_HARD" in place we
cannot use I2C EEPROM any longer so we're dropping all references to
both EEPROM and I2C which was only used for EEPROM.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Simon Glass <sjg@chromium.org>
since commit: f8b7fff1d5 "serial: atmel_usart: Add clk support"
taurus board comes not up anymore. Fix it.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Wenyou Yang <wenyou.yang@microchip.com>
since commit: f8b7fff1d5 "serial: atmel_usart: Add clk support"
smartweb board comes not up anymore. Fix it.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Wenyou Yang <wenyou.yang@microchip.com>
The CONFIG_DEFAULT_FDT_FILE expects just the file not a full path
as that might vary depending on the variant of Linux distro you
might be using.
Cc: Martin Donnelly <martin.donnelly@ge.com>
Cc: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Acked-by: Fabio Estevam <fabio.estevam@nxp.com>
The ti816x SoC revision of the ethernet IP block is handled by the
"davinci_emac" driver, rather than the "cpsw" driver as done by later
members of the family. Enable the relevant plumbing.
Signed-off-by: Sriramakrishnan <srk@ti.com>
Signed-off-by: Vitaly Wool <vitaly.wool@konsulko.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The commit "fb82fe385173 configs: Resync defconfigs" resynced all config
files. This exposed two latent issues with the Gen3 boards in that we
had not been setting CONFIG_DEFAULT_FDT_FILE correctly and had not been
setting CONFIG_CMD_MMC. Fix both of these.
Fixes: fb82fe3851 ("configs: Resync defconfigs")
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
The topic-miamilite SoM contains a Zynq xc7z010 SoC, 1GB DDR3L RAM,
64MB dual-parallel QSPI NOR flash and clock sources.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Move the only use of CONFIG_SF_DUAL_FLASH to defconfig. This makes the
associated topic_miamiplus.h header obsolete, so remove that as well.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There was for long time no activity in the mpx5xxx area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in mpc5xxx,
so remove it.
Signed-off-by: Heiko Schocher <hs@denx.de>
Adds CONFIG_SPL_USB_GADGET_SUPPORT and CONFIG_SPL_USBETH_SUPPORT.
Removes CONFIG_SPL_NAND_SUPPORT, CONFIG_SPL_MTD_SUPPORT, and CONFIG_SPL_YMODEM_SUPPORT
to free up space to fit in RAM.
Signed-off-by: Michael Welling <mwelling@ieee.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marek Vasut <marex@denx.de>
NanoPi NEO2 is designed and developed by FriendlyElec
using the Allwinner 64-bit H5 SOC.
NanoPi Neo2 key features
- Allwinner H5, Quad-core 64-bit Cortex-A53
- 512MB DDR3 RAM
- microSD slot
- 10/100/1000M Ethernet
- Serial Debug Port
- 5V 2A DC MicroUSB power-supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Orangepi Win/WinPlus is an open-source single-board computer
using the Allwinner A64 SOC.
A64 Orangepi Win/WinPlus has
- A64 Quad-core Cortex-A53 64bit
- 1GB(Win)/2GB(Win Plus) DDR3 SDRAM
- Debug TTL UART
- Four USB 2.0
- HDMI
- LCD
- Audio and MIC
- Wifi + BT
- IR receiver
- 5V DC power supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Orangepi Zero Plus 2 is an open-source single-board computer
using the Allwinner h5 SOC.
H5 Orangepi Zero Plus 2 has
- Quad-core Cortex-A53
- 512MB DDR3
- micrSD slot and 8GB eMMC
- Debug TTL UART
- HDMI
- Wifi + BT
- OTG+power supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Whistler is an ancient Tegra 2 reference board. I may have been the only
person who ever used it with upstream software, and I've just recycled
the board hardware. Hence, it makes sense to remove support from software.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Enable DHCP command by default. Move environmental variable location
to before U-Boot image. Enlarge reserved mem for malloc. Update
maintainer.
Signed-off-by: York Sun <york.sun@nxp.com>
There was for long time no activity in the 5xx area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in 5xx,
so remove it.
Signed-off-by: Heiko Schocher <hs@denx.de>
There was for long time no activity in the 8260 area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in 8260,
so remove it.
Signed-off-by: Heiko Schocher <hs@denx.de>
There was for long time no activity in the 8xx area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in 8xx,
so remove it (with a heavy heart, knowing that I remove
here the root of U-Boot).
Signed-off-by: Heiko Schocher <hs@denx.de>
CONFIG_FAT_WRITE is imply'ed when CONFIG_CMD_FAT
is selected (see CONFIG_TI_COMMON_CMD_OPTIONS).
Dont disable it in defconfig so the imply takes
effect and 'fatwrite' is available for users.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Like commit 3337e3af5d this enables suitable commands needed for booting
general purpose Linux distribution. This is required for example if we want
to use PXE or DHCP as default boot targets, symbols no longer enabled by
config_distro_defaults.h.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Almost all users of CONFIG_AM33XX/AM43XX have been migrated. Finish
moving the last few over to Kconfig, and put all of the boards under the
appropriate Kconfig chocie now. This board choice is non-optional, so
remove that keyword on am33xx.
Signed-off-by: Tom Rini <trini@konsulko.com>
The display on jerry is so fast that this option is not needed. Drop it so
that the display scrolls more smoothly.
Signed-off-by: Simon Glass <sjg@chromium.org>
If U-Boot is chain-loaded from a previous boot loader we must set up the
clocks the way U-Boot wants them. Add code for this. It will do nothing if
SPL has already done the job.
Signed-off-by: Simon Glass <sjg@chromium.org>
Enable this so we can roughly measure CPU performance. Also enable the
cache command to allow for timing.
Signed-off-by: Simon Glass <sjg@chromium.org>
This commit supports booting from stm32 internal nor flash. spl U-Boot
initializes the sdram memory, copies next image (e.g. standard U-Boot)
to sdram & then jumps to entry point.
Here are the flash memory addresses for U-Boot-spl & standard U-Boot:
- spl U-Boot : 0x0800_0000
- standard U-Boot : 0x0800_8000
To compile u-boot without spl: Remove SUPPORT_SPL configuration
(arch/arm/mach-stm32/Kconfig)
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
[trini: Rework Kconfig logic a bit]
Signed-off-by: Tom Rini <trini@konsulko.com>
The SoPine is a SoM by Pine64, with an Allwinner A64 SoC, a LPDDR3 DRAM
chip, an AXP803 PMIC, a SPI NOR Flash and a MicroSD slot. The card
detect pin of the MicroSD slot is broken, however, it doesn't matter as
the design of SoPine didn't allow hot-swapping the MicroSD card (The
MicroSD slot is at the back of the SoM, and when the SoM is installed on
the baseboard, it's nearly impossible to remove the MicroSD).
The official baseboard of it is a board with nearly the same connectors
with the original Pine64+, with the MicroUSB power jack replaced, and
at the position of MicroSD slot a eMMC module slot is added.
Add support for SoPine with the official baseboard by adding its
defconfig file. It still uses the device tree of Pine64, however, it
will change after a proper device tree of SoPine with baseboard is
accepted by Linux mainline.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
[Update board/sunxi/MAINTAINERS]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
NanoPi M1 Plus is designed and developed by FriendlyElec
for professionals, enterprise users, makers and hobbyists
using the Allwinner H3 SOC.
NanoPi M1 Plus key features
- Allwinner H3, Quad-core Cortex-A7@1.2GHz
- 1GB DDR3 RAM
- 8GB eMMC
- microSD slot
- 10/100/1000M Ethernet
- Serial Debug Port
- 5V 2A DC power-supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
For the RK3399-Q7, we need spl_board_init to be called during SPL
startup to set up the pinmux for the debug UART. Enable SPL_BOARD_INIT
via defconfig to ensure this function is in fact called.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
To better support different RAM timings (DDR3-1333 and DDR3-1866 are
assembly options for the RK3399-Q7), this refactors the DTS support
and renames the default DTS variant from rk3399-puma to
rk3399-puma-ddr1600:
- changes the rk3399-puma DTS into a board-specific DTSI by removing
the inclusion of the DRAM timings
- adds a new rk3399-puma-ddr1600.dts, which includes the (new) common
board DTSI and the DDR3-1600 timing DTSI
- wires this up from arch/arm/dts/Makefile and configs/puma-rk3399_defconfig
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
With HDMI output for the RK3399 working, this update the RK3399-Q7
(Puma) defconfig for the new functionality:
1. enables PMIC command (to check if the HDMI voltages are correct)
+CONFIG_CMD_PMIC=y
+CONFIG_CMD_REGULATOR=y
2. enables video-output (via HDMI)
+CONFIG_DM_VIDEO=y
+CONFIG_DISPLAY=y
+CONFIG_VIDEO_ROCKCHIP=y
+CONFIG_DISPLAY_ROCKCHIP_HDMI=y
3. turns on the 'dcache'-command (for a dcache flush) for our QA to
fill the framebuffer using 'mw.l'
+CONFIG_CMD_CACHE=y
4. turns on the 'bmp'-command
+CONFIG_CMD_BMP=y
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Add basic support for rv1108 evb, whith this patch we
can boot into u-boot console.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
For the RK3399-Q7 module, we use full OF_CONTROL (i.e. not
OF_PLATDATA) for SPL. In this configuration, the rockchip_dw_mmc
driver retrieves one of its clocks via clk_get_by_name and fails if
this is not possible. For this reason, we can not filter clock-names
from the device-tree nodes used for the configuration of the SPL
stage.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The RK3399-Q7 exposes I2C on its edge connector and uses it as one of
the interfaces towards the on-module STM32 (for the emulated RTC and
fan-controller).
Enable I2C and CMD_I2C support in the defconfig.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The RK3399-Q7 has a KSZ9031 GbE PHY. Enable support for it in defconfig.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
On the RK3399-Q7, we need PMIC support (for the RK808) to enable HDMI
output, as one of the required powerrails is not enabled on boot.
For this, we need to enable the RK808 driver.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Version-changes: 3
- With the recent upstream changes to the RK808 (PMIC) driver, the
associated configuration options have been renamed to RK8XX. Track
this change in the RK3399-Q7 defconfig.
Reviewed-by: Simon Glass <sjg@chromium.org>
Add config of max root ports and add config to enable xhci
controller.
Signed-off-by: Meng Dongyang <daniel.meng@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add defconfig for usb and ehci and ohci controller, config maximal
number of ports of the root hub for ohci driver.
Signed-off-by: Meng Dongyang <daniel.meng@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
PX5 EVB is designed by Rockchip for automotive field
with integrated CVBS (TP2825) / MIPI DSI / CSI / LVDS
HDMI video input/output interface, audio codec ES8396,
WIFI / BT (on RTL8723BS), Gsensor BMA250E and light&proximity
sensor STK3410.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The GeekBox is a TV box from GeekBuying, based on an MXM3 module.
The module can be used with base boards such as the GeekBox Landingship.
This adds basic support to chain-load U-Boot from Rockchip's miniloader.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Sheep board is designed by Rockchip as a EVB for rk3368.
Currently it is able to boot a linux kernel and system
to console with the miniloader run as fist level loader.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
With everything in place (i.e. the new efuse driver, the clk-support
for the non-secure efuse block, and the board-specific functions to
derive 'serial#' from the cpu-id within the efuses), enable this in
the RK3399-Q7 defconfig.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
The option is named PINCTRL_ROCKCHIP_RK3399 not ROCKCHIP_RK3399_PINCTRL.
Set the correct option.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
Supported boot devices are raw QSPI and raw SD card.
Add support for a FAT16/32 file system for SD card.
The SOC's boot ROM only supports FAT file system.
Therefore remove the SPL support for the EXT file system.
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
The symbol CONFIG_TI81XX is used for the parts that are common to the
TI816x and TI814x SoCs and are not part of CONFIG_ARCH_OMAP2PLUS nor
CONFIG_AM33XX. It however has so few uses that we can just modify the
code to check for both and drop the symbol. The symbols CONFIG_TI816X
and CONFIG_TI814X are for the repective SoCs.
Signed-off-by: Tom Rini <trini@konsulko.com>
- Switch to using <configs/ti_armv7_omap.h> and family. This lets us
drop lots of custom defines.
- Ensure that our default environment uses DEFAULT_LINUX_BOOT_ENV so
that Linux will boot correctly.
- Enable CONFIG_DISTRO_DEFAULTS
- Switch to using CONFIG_OF_CONTROL
- Various other cleanups to match other SoCs in the family line.
Signed-off-by: Tom Rini <trini@konsulko.com>
On this platform, we can trace a general failure to boot to enabling /
disabling this option. When this is enabled, we go off into the
weeds during SPL and are unable to talk with the SD card and
mmc_initialize() fails.
Signed-off-by: Tom Rini <trini@konsulko.com>
Any TFTP or DHCP boot on the Davinci OMAP-L138 LCDK board requires
that the 'ethaddr' variable be defined. There are no e-fuses to store
the ethernet mac address for this platform, and neither is a MAC
address reserved in any format. So enable random MAC address support
so that networking boot can be supported.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Remove the CONFIG_I2C_COMPAT, instead enable the CONFIG_SYS_I2C_S3C24X0.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Now that these symbols are in Kconfig, migrate all users. Use imply on
a number of platforms that default to having this enabled. As part of
this we must migrate some straglers for CMD_FAT and DOS_PARTITION.
Signed-off-by: Tom Rini <trini@konsulko.com>
Orangepi Prime is an open-source single-board computer
using the Allwinner h5 SOC.
H5 Orangepi Prime has
- Quad-core Cortex-A53
- 2GB DDR3
- Debug TTL UART
- 1000M/100M Ethernet RJ45
- Three USB 2.0
- HDMI
- Audio and MIC
- Wifi + BT
- IR receiver
- HDMI
- Wifi + BT
Boot from MMC:
-------------
U-Boot SPL 2017.05-00662-ga3f4c05-dirty (May 25 2017 - 13:30:14)
DRAM: 2048 MiB
Trying to boot from MMC1
NOTICE: BL3-1: Running on H5 (1718) in SRAM A2 (@0x44000)
NOTICE: Configuring SPC Controller
NOTICE: BL3-1: v1.0(debug):aa75c8d
NOTICE: BL3-1: Built : 18:28:27, May 24 2017
INFO: BL3-1: Initializing runtime services
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address: 0x4a000000, SPSR: 0x3c9
U-Boot 2017.05-00662-ga3f4c05-dirty (May 25 2017 - 13:30:14 +0000) Allwinner Technology
CPU: Allwinner H5 (SUN50I)
Model: OrangePi Prime
DRAM: 2 GiB
MMC: SUNXI SD/MMC: 0
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: phy interface7
eth0: ethernet@1c30000
starting USB...
USB0: USB EHCI 1.00
USB1: USB OHCI 1.0
scanning bus 0 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
Hit any key to stop autoboot: 0
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
CONFIG_SPL_BOARD_INIT is used for SPL boot. It is only enabled for
secure boot at this moment. Enable it in defconfig files for SPL
build.
Signed-off-by: York Sun <york.sun@nxp.com>
Add CONFIG_NAND_BOOT config flag to organise
NAND_BOOT specific code in config flag like
-nand-boot specfic errata errata_rcw_src()
-CONFIG_SYS_NAND_U_BOOT_DST,etc
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Abhimanyu Saini <abhimanyu.saini@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This updates sandbox to use a live device tree. This means that after
relocation (from board_init_r() onwards) it no-longer uses flat device
tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a sandbox board to test the non-livetree build (i.e. with
CONFIG_OF_FLAT disabled). This increases our build and test coverage.
Signed-off-by: Simon Glass <sjg@chromium.org>
Enable CONFIG_DM_MMC_OPS and CONFIG_BLK for all Tegra devices. This moves
Tegra to use driver model fully for MMC.
Signed-off-by: Simon Glass <sjg@chromium.org>
BPI-M64 is a 64-bit quad-core mini single board computer
using the Allwinner A64 SOC.
BPI-M64 features
- 1.2 Ghz Quad-Core ARM Cortex A53
- 2GB DDR3 SDRAM with 733MHz
- MicroSD/eMMC(8GB)
- 10/100/1000Mbps ethernet (Realtek RTL8211E/D)
- Wifi + BT
- IR receiver
- Audio In/Out
- Video In/Out
- 5V 2A DC power-supply
For dts file,
Sync with Linux commit 4879b7ae("Merge tag 'dmaengine-4.12-rc1'").
Boot from MMC:
-------------
U-Boot SPL 2017.05-00667-g85dd258-dirty (May 29 2017 - 13:07:31)
DRAM: 2048 MiB
Trying to boot from MMC1
NOTICE: BL3-1: Running on A64/H64 (1689) in SRAM A2 (@0x44000)
NOTICE: Configuring SPC Controller
NOTICE: BL3-1: v1.0(debug):aa75c8d
NOTICE: BL3-1: Built : 18:28:27, May 24 2017
NOTICE: Configuring AXP PMIC
NOTICE: PMIC: setup successful
INFO: BL3-1: Initializing runtime services
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address: 0x4a000000, SPSR: 0x3c9
U-Boot 2017.05-00667-g85dd258-dirty (May 29 2017 - 13:07:31 +0000) Allwinner Technology
CPU: Allwinner A64 (SUN50I)
Model: BananaPi-M64
DRAM: 2 GiB
MMC: SUNXI SD/MMC: 0, SUNXI SD/MMC: 1
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: No ethernet found.
starting USB...
No controllers found
Hit any key to stop autoboot: 0
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Currently these (board agnostic) commands cannot be selected using
menuconfig and friends. Fix this the obvious way. As part of this,
don't muddle the meaning of CONFIG_HASH_VERIFY to mean both 'hash -v'
and "we have a hashing command" as this makes the Kconfig logic odd.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
[trini: Re-apply, add imply for a few cases, run moveconfig.py, also
migrate CRC32_VERIFY]
Signed-off-by: Tom Rini <trini@konsulko.com>
As mx6sabresd only supports SPL target now, there is no need to
keep the 'spl' in the name of the target, so simply rename it
to mx6sabresd_defconfig.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
nand defconfig is accidentally removed from below
commit, so recover the same.
"icorem6: Make SPL to pick suitable fdt"
(sha1: 15455a6b01)
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add the initial support for pico-imx7d board based on Wig Cheng's
source code.
Add support for eMMC, USB gadget, I2C, PMIC and Ethernet.
For more information about this board, please visit:
http://www.technexion.org/products/pico/pico-som/pico-imx7-emmc
Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Switch Clearfog to the generic distro defaults. This has been taken
from a Debian mailing list thread:
https://lists.debian.org/debian-boot/2016/10/msg00026.html
Signed-off-by: Patrick Wildt <patrick@blueri.se>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch enable the PINCTRL and GPIO support, including the GPIO
command on the Armada 3720 DB.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Konstantin Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
To enable support for the Armada 37xx pinctrl driver, we need to
change the Kconfig symbol for the Armada 7k/8k pinctrl driver and its
dependencies to distinguish between both platforms and drivers.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Konstantin Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
NanoPi M1 is a board based on Allwinner H3 CPU.
This commit adds the support for this platform with:
- an include device tree which enables UART, LEDs, GPIO key switch,
1 USB host ports and the SD-card as a dtsi file.
- a device tree specific to this board that enables the
2 additional USB ports
- a defconfig file for minimal support
- a section in MAINTAINERS (add myself)
Synchronized with the kernel device tree, from commits:
sun8i-nanopi.dtsi: 85d2913614d9ab899d23b7ab7d22d23cf45bd1de
sun8i-h3-nanopi-m1.dts: 10efbf5f16336b7540ad6a16aa1cb0b26bab033b
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
LS2081ARDB board is similar to LS2080ARDB board with few differences
It hosts LS2081A SoC
Default boot source is QSPI-boot
It does not have IFC interface
RTC and QSPI flash device are different
It provides QIXIS access via I2C
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
On the A33, uart0 is muxed on the PB pins. On SBCs these pins may be
available for use. Such is the case on the Sinlinx SinA33.
Set CONS_INDEX=1 to use uart0 as the console, matching the device tree.
Fixes: 7095f86418 ("sunxi: Convert CONS_INDEX to Kconfig")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
QSPI-boot is supported on LS2088ARDB RevF board with LS2088A SoC.
LS2088ARDB RevF Board has limitation that QIXIS can not be accessed.
CONFIG_FSL_QIXIS is not enabled.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
trini: Make Kconfig SPL_xxx entires only show if SPL, so that we don't
get Kconfig errors on platforms without SPL, ie sandbox (without SPL).
Signed-off-by: Tom Rini <trini@konsulko.com>
