Mirrors/u-boot
2
0
Fork 0
mirror of https://github.com/AsahiLinux/u-boot synced 2024-11-10 15:14:43 +00:00
Code Issues Projects Releases Packages Wiki Activity

i2c: Drop use of CONFIG_I2C_HARD

Browse source 
This option is pretty old. It predates CONFIG_SYS_I2C which is itself
deprecated in favour of driver model. Disable it for all boards.

Also drop I2C options which depend on this.

Signed-off-by: Simon Glass <sjg@chromium.org>
This commit is contained in:
Simon Glass 2017-05-12 21:09:49 -06:00 committed by Heiko Schocher
parent 22f3368e71
commit eb5ba3aefd
81 changed files with 211 additions and 701 deletions
Show stats Download patch file Download diff file Expand all files Collapse all files

17
README
View file

@ -2213,22 +2213,9 @@ The following options need to be configured:
- approved multibus support
- better i2c mux support
** Please consider updating your I2C driver now. **
** CONFIG_HARD_I2C is now being removed **
These enable legacy I2C serial bus commands. Defining
CONFIG_HARD_I2C will include the appropriate I2C driver
for the selected CPU.
This will allow you to use i2c commands at the u-boot
command line (as long as you set CONFIG_CMD_I2C in
CONFIG_COMMANDS) and communicate with i2c based realtime
clock chips. See common/cmd_i2c.c for a description of the
command line interface.
CONFIG_HARD_I2C selects a hardware I2C controller.
There are several other quantities that must also be
defined when you define CONFIG_HARD_I2C.
----under removal:
In both cases you will need to define CONFIG_SYS_I2C_SPEED
to be the frequency (in Hz) at which you wish your i2c bus

12
arch/arm/include/asm/arch-armada100/config.h
View file

@ -24,17 +24,5 @@
#define MV_UART_CONSOLE_BASE ARMD1_UART1_BASE
#define CONFIG_SYS_NS16550_IER (1 << 6) /* Bit 6 in UART_IER register
represents UART Unit Enable */
/*
* I2C definition
*/
#ifdef CONFIG_CMD_I2C
#define CONFIG_I2C_MV 1
#define CONFIG_MV_I2C_NUM 2
#define CONFIG_I2C_MULTI_BUS 1
#define CONFIG_MV_I2C_REG {0xd4011000, 0xd4025000}
#define CONFIG_HARD_I2C 1
#define CONFIG_SYS_I2C_SPEED 0
#define CONFIG_SYS_I2C_SLAVE 0xfe
#endif
#endif /* _ARMD1_CONFIG_H */

12
board/alphaproject/ap_sh4a_4a/ap_sh4a_4a.c
View file

@ -156,17 +156,7 @@ int board_init(void)
int board_late_init(void)
{
u8 mac[6];
/* Read Mac Address and set*/
i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
i2c_set_bus_num(CONFIG_SYS_I2C_MODULE);
/* Read MAC address */
i2c_read(0x50, 0x0, 0, mac, 6);
if (is_valid_ethaddr(mac))
eth_setenv_enetaddr("ethaddr", mac);
printf("Cannot use I2C to get MAC address\n");
return 0;
}

32
board/cm5200/cm5200.c
View file

@ -161,14 +161,7 @@ int dram_init(void)
*/
static void read_hw_id(hw_id_t hw_id)
{
int i;
for (i = 0; i < HW_ID_ELEM_COUNT; ++i)
if (i2c_read(CONFIG_SYS_I2C_EEPROM,
hw_id_format[i].offset,
2,
(uchar *)&hw_id[i][0],
hw_id_format[i].length) != 0)
printf("ERROR: can't read HW ID from EEPROM\n");
printf("ERROR: can't read HW ID from EEPROM\n");
}
@ -221,7 +214,7 @@ static void compose_module_name(hw_id_t hw_id, char *buf)
strcat(buf, tmp);
}
#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C_SOFT)
/*
* Compose string with hostname.
* buf is assumed to have enough space, and be null-terminated.
@ -237,7 +230,7 @@ static void compose_hostname(hw_id_t hw_id, char *buf)
*p = tolower(*p);
}
#endif
#ifdef CONFIG_OF_BOARD_SETUP
/*
@ -270,15 +263,6 @@ int checkboard(void)
hw_id_t hw_id_tmp;
char module_name_tmp[MODULE_NAME_MAXLEN] = "";
/*
* We need I2C to access HW ID data from EEPROM, so we call i2c_init()
* here despite the fact that it will be called again later on. We
* also use a little trick to silence I2C-related output.
*/
gd->flags |= GD_FLG_SILENT;
i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
gd->flags &= ~GD_FLG_SILENT;
read_hw_id(hw_id_tmp);
identify_module(hw_id_tmp); /* this sets gd->board_type */
compose_module_name(hw_id_tmp, module_name_tmp);
@ -334,16 +318,16 @@ int misc_init_r(void)
" device at address %02X:%04X\n", CONFIG_SYS_I2C_EEPROM,
CONFIG_MAC_OFFSET);
}
hostname[0] = 0x00;
/* set the hostname appropriate to the module we're running on */
compose_hostname(hw_id, hostname);
setenv("hostname", hostname);
#endif /* defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C_SOFT) */
if (!getenv("ethaddr"))
printf(LOG_PREFIX "MAC address not set, networking is not "
"operational\n");
/* set the hostname appropriate to the module we're running on */
hostname[0] = 0x00;
compose_hostname(hw_id, hostname);
setenv("hostname", hostname);
return 0;
}
#endif /* CONFIG_MISC_INIT_R */

32
board/cm5200/cmd_cm5200.c
View file

@ -13,34 +13,6 @@
#ifdef CONFIG_CMD_BSP
static int do_i2c_test(char * const argv[])
{
unsigned char temp, temp1;
printf("Starting I2C Test\n"
"Please set Jumper:\nI2C SDA 2-3\nI2C SCL 2-3\n\n"
"Please press any key to start\n\n");
getc();
temp = 0xf0; /* set io 0-4 as output */
i2c_write(CONFIG_SYS_I2C_IO, 3, 1, (uchar *)&temp, 1);
printf("Press I2C4-7. LED I2C0-3 should have the same state\n\n"
"Press any key to stop\n\n");
while (!tstc()) {
i2c_read(CONFIG_SYS_I2C_IO, 0, 1, (uchar *)&temp, 1);
temp1 = (temp >> 4) & 0x03;
temp1 |= (temp >> 3) & 0x08; /* S302 -> LED303 */
temp1 |= (temp >> 5) & 0x04; /* S303 -> LED302 */
temp = temp1;
i2c_write(CONFIG_SYS_I2C_IO, 1, 1, (uchar *)&temp, 1);
}
getc();
return 0;
}
static int do_usb_test(char * const argv[])
{
int i;
@ -387,9 +359,7 @@ static int cmd_fkt(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
switch (argc) {
case 2:
if (strncmp(argv[1], "i2c", 3) == 0)
rcode = do_i2c_test(argv);
else if (strncmp(argv[1], "led", 3) == 0)
if (strncmp(argv[1], "led", 3) == 0)
rcode = do_led_test(argv);
else if (strncmp(argv[1], "usb", 3) == 0)
rcode = do_usb_test(argv);

3
board/davedenx/aria/aria.c
View file

@ -29,9 +29,6 @@ int misc_init_r(void)
{
u32 tmp;
/* we use I2C-2 for on-board eeprom */
i2c_set_bus_num(2);
tmp = in_be32((u32*)CONFIG_SYS_ARIA_FPGA_BASE);
printf("FPGA: %u-%u.%u.%u\n",
(tmp & 0xFF000000) >> 24,

12
board/esd/mecp5123/mecp5123.c
View file

@ -18,17 +18,7 @@ DECLARE_GLOBAL_DATA_PTR;
int eeprom_write_enable(unsigned dev_addr, int state)
{
volatile immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
if (dev_addr != CONFIG_SYS_I2C_EEPROM_ADDR)
return -1;
if (state == 0)
setbits_be32(&im->gpio.gpdat, 0x00100000);
else
clrbits_be32(&im->gpio.gpdat, 0x00100000);
return 0;
return -ENOSYS;
}
int board_early_init_f(void)

21
board/freescale/mpc5121ads/mpc5121ads.c
View file

@ -174,27 +174,6 @@ int dram_init(void)
int misc_init_r(void)
{
u8 tmp_val;
/* Using this for DIU init before the driver in linux takes over
* Enable the TFP410 Encoder (I2C address 0x38)
*/
i2c_set_bus_num(2);
tmp_val = 0xBF;
i2c_write(0x38, 0x08, 1, &tmp_val, sizeof(tmp_val));
/* Verify if enabled */
tmp_val = 0;
i2c_read(0x38, 0x08, 1, &tmp_val, sizeof(tmp_val));
debug("DVI Encoder Read: 0x%02x\n", tmp_val);
tmp_val = 0x10;
i2c_write(0x38, 0x0A, 1, &tmp_val, sizeof(tmp_val));
/* Verify if enabled */
tmp_val = 0;
i2c_read(0x38, 0x0A, 1, &tmp_val, sizeof(tmp_val));
debug("DVI Encoder Read: 0x%02x\n", tmp_val);
return 0;
}

53
board/ifm/ac14xx/ac14xx.c
View file

@ -17,7 +17,6 @@
#include <i2c.h>
#endif
static int eeprom_diag;
static int mac_diag;
static int gpio_diag;
@ -136,7 +135,6 @@ struct __attribute__ ((__packed__)) eeprom_layout {
#define HW_COMP_MAINCPU 2
static struct eeprom_layout eeprom_content;
static int eeprom_was_read; /* has_been_read */
static int eeprom_is_valid;
static int eeprom_version;
@ -153,53 +151,7 @@ static int eeprom_version;
static int read_eeprom(void)
{
int eeprom_datalen;
int ret;
if (eeprom_was_read)
return 0;
eeprom_is_valid = 0;
ret = i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0,
CONFIG_SYS_I2C_EEPROM_ADDR_LEN,
(uchar *)&eeprom_content, sizeof(eeprom_content));
if (eeprom_diag) {
printf("DIAG: %s() read rc[%d], size[%d]\n",
__func__, ret, sizeof(eeprom_content));
}
if (ret != 0)
return -1;
eeprom_was_read = 1;
/*
* check validity of EEPROM content
* (check version, length, optionally checksum)
*/
eeprom_is_valid = 1;
eeprom_datalen = get_eeprom_field_int(eeprom_content.len);
eeprom_version = get_eeprom_field_int(eeprom_content.version);
if (eeprom_diag) {
printf("DIAG: %s() magic[%c%c%c] len[%d] ver[%d] type[%d]\n",
__func__, eeprom_content.magic[0],
eeprom_content.magic[1], eeprom_content.magic[2],
eeprom_datalen, eeprom_version, eeprom_content.type);
}
if (strncmp(eeprom_content.magic, "ifm", strlen("ifm")) != 0)
eeprom_is_valid = 0;
if (eeprom_datalen < sizeof(struct eeprom_layout) - 5)
eeprom_is_valid = 0;
if ((eeprom_version != 1) && (eeprom_version != 2))
eeprom_is_valid = 0;
if (eeprom_content.type != HW_COMP_MAINCPU)
eeprom_is_valid = 0;
if (eeprom_diag)
printf("DIAG: %s() valid[%d]\n", __func__, eeprom_is_valid);
return ret;
return -ENOSYS;
}
int mac_read_from_eeprom(void)
@ -324,9 +276,6 @@ int misc_init_r(void)
char *s;
int want_recovery;
/* we use bus I2C-0 for the on-board eeprom */
i2c_set_bus_num(0);
/* setup GPIO directions and initial values */
gpio_configure();

12
board/renesas/r0p7734/r0p7734.c
View file

@ -44,17 +44,7 @@ int board_init(void)
int board_late_init(void)
{
u8 mac[6];
/* Read Mac Address and set*/
i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
i2c_set_bus_num(CONFIG_SYS_I2C_MODULE);
/* Read MAC address */
i2c_read(0x50, 0x10, 0, mac, 6);
if (is_valid_ethaddr(mac))
eth_setenv_enetaddr("ethaddr", mac);
printf("Cannot get MAC address from I2C\n");
return 0;
}

18
board/tqc/tqm5200/tqm5200.c
View file

@ -486,20 +486,14 @@ int board_early_init_f (void)
static int tfp410_read_reg(int reg, uchar *buf)
{
if (i2c_read(CONFIG_SYS_TFP410_ADDR, reg, 1, buf, 1) != 0) {
puts ("Error reading the chip.\n");
return 1;
}
return 0;
puts("Error reading the chip.\n");
return -ENOSYS;
}
static int tfp410_write_reg(int reg, uchar buf)
{
if (i2c_write(CONFIG_SYS_TFP410_ADDR, reg, 1, &buf, 1) != 0) {
puts ("Error writing the chip.\n");
return 1;
}
return 0;
puts("Error writing the chip.\n");
return -ENOSYS;
}
typedef struct _tfp410_config {
@ -525,12 +519,9 @@ static int charon_last_stage_init(void)
{
volatile struct mpc5xxx_lpb *lpb =
(struct mpc5xxx_lpb *) MPC5XXX_LPB;
int oldbus = i2c_get_bus_num();
uchar buf;
int i = 0;
i2c_set_bus_num(CONFIG_SYS_TFP410_BUS);
/* check version */
if (tfp410_read_reg(TFP410_REG_DEV_ID_H, &buf) != 0)
return -1;
@ -551,7 +542,6 @@ static int charon_last_stage_init(void)
i++;
}
printf("TFP410 initialized.\n");
i2c_set_bus_num(oldbus);
/* set deadcycle for cs3 to 0 */
setbits_be32(&lpb->cs_deadcycle, 0xffffcfff);

2
configs/MiniFAP_defconfig
View file

@ -10,7 +10,6 @@ CONFIG_SYS_CONSOLE_IS_IN_ENV=y
CONFIG_HUSH_PARSER=y
CONFIG_CMD_ASKENV=y
CONFIG_LOOPW=y
CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
@ -19,7 +18,6 @@ CONFIG_CMD_PING=y
CONFIG_CMD_SNTP=y
CONFIG_CMD_BMP=y
CONFIG_CMD_BSP=y
CONFIG_CMD_DATE=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_FAT=y
CONFIG_CMD_DIAG=y

1
configs/O2D300_defconfig
View file

@ -4,7 +4,6 @@ CONFIG_TARGET_O2D300=y
CONFIG_OF_BOARD_SETUP=y
CONFIG_BOOTDELAY=5
CONFIG_HUSH_PARSER=y
CONFIG_CMD_I2C=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y

1
configs/O2DNT2_RAMBOOT_defconfig
View file

@ -8,7 +8,6 @@ CONFIG_HUSH_PARSER=y
CONFIG_AUTOBOOT_KEYED=y
CONFIG_AUTOBOOT_PROMPT="Autobooting in %d seconds, press password to stop\n"
CONFIG_AUTOBOOT_STOP_STR="++++++++++"
CONFIG_CMD_I2C=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y

1
configs/O2DNT2_defconfig
View file

@ -7,7 +7,6 @@ CONFIG_HUSH_PARSER=y
CONFIG_AUTOBOOT_KEYED=y
CONFIG_AUTOBOOT_PROMPT="Autobooting in %d seconds, press password to stop\n"
CONFIG_AUTOBOOT_STOP_STR="++++++++++"
CONFIG_CMD_I2C=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y

1
configs/O2D_defconfig
View file

@ -4,7 +4,6 @@ CONFIG_TARGET_O2D=y
CONFIG_OF_BOARD_SETUP=y
CONFIG_BOOTDELAY=5
CONFIG_HUSH_PARSER=y
CONFIG_CMD_I2C=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y

1
configs/O2I_defconfig
View file

@ -4,7 +4,6 @@ CONFIG_TARGET_O2I=y
CONFIG_OF_BOARD_SETUP=y
CONFIG_BOOTDELAY=5
CONFIG_HUSH_PARSER=y
CONFIG_CMD_I2C=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y

1
configs/O2MNT_O2M110_defconfig
View file

@ -5,7 +5,6 @@ CONFIG_OF_BOARD_SETUP=y
CONFIG_SYS_EXTRA_OPTIONS="IFM_SENSOR_TYPE=\"O2M110\""
CONFIG_BOOTDELAY=5
CONFIG_HUSH_PARSER=y
CONFIG_CMD_I2C=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y

1
configs/O2MNT_O2M112_defconfig
View file

@ -5,7 +5,6 @@ CONFIG_OF_BOARD_SETUP=y
CONFIG_SYS_EXTRA_OPTIONS="IFM_SENSOR_TYPE=\"O2M112\""
CONFIG_BOOTDELAY=5
CONFIG_HUSH_PARSER=y
CONFIG_CMD_I2C=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y

1
configs/O2MNT_O2M113_defconfig
View file

@ -5,7 +5,6 @@ CONFIG_OF_BOARD_SETUP=y
CONFIG_SYS_EXTRA_OPTIONS="IFM_SENSOR_TYPE=\"O2M113\""
CONFIG_BOOTDELAY=5
CONFIG_HUSH_PARSER=y
CONFIG_CMD_I2C=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y

1
configs/O2MNT_defconfig
View file

@ -4,7 +4,6 @@ CONFIG_TARGET_O2MNT=y
CONFIG_OF_BOARD_SETUP=y
CONFIG_BOOTDELAY=5
CONFIG_HUSH_PARSER=y
CONFIG_CMD_I2C=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y

1
configs/O3DNT_defconfig
View file

@ -4,7 +4,6 @@ CONFIG_TARGET_O3DNT=y
CONFIG_OF_BOARD_SETUP=y
CONFIG_BOOTDELAY=5
CONFIG_HUSH_PARSER=y
CONFIG_CMD_I2C=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y

2
configs/TQM5200S_HIGHBOOT_defconfig
View file

@ -7,7 +7,6 @@ CONFIG_BOOTDELAY=5
CONFIG_HUSH_PARSER=y
CONFIG_CMD_ASKENV=y
CONFIG_LOOPW=y
CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
@ -15,7 +14,6 @@ CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
CONFIG_CMD_SNTP=y
CONFIG_CMD_BSP=y
CONFIG_CMD_DATE=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_FAT=y
CONFIG_CMD_DIAG=y

2
configs/TQM5200S_defconfig
View file

@ -7,7 +7,6 @@ CONFIG_BOOTDELAY=5
CONFIG_HUSH_PARSER=y
CONFIG_CMD_ASKENV=y
CONFIG_LOOPW=y
CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
@ -15,7 +14,6 @@ CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
CONFIG_CMD_SNTP=y
CONFIG_CMD_BSP=y
CONFIG_CMD_DATE=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_FAT=y
CONFIG_CMD_DIAG=y

2
configs/TQM5200_B_HIGHBOOT_defconfig
View file

@ -10,7 +10,6 @@ CONFIG_SYS_CONSOLE_IS_IN_ENV=y
CONFIG_HUSH_PARSER=y
CONFIG_CMD_ASKENV=y
CONFIG_LOOPW=y
CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
@ -19,7 +18,6 @@ CONFIG_CMD_PING=y
CONFIG_CMD_SNTP=y
CONFIG_CMD_BMP=y
CONFIG_CMD_BSP=y
CONFIG_CMD_DATE=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_FAT=y
CONFIG_CMD_DIAG=y

2
configs/TQM5200_B_defconfig
View file

@ -10,7 +10,6 @@ CONFIG_SYS_CONSOLE_IS_IN_ENV=y
CONFIG_HUSH_PARSER=y
CONFIG_CMD_ASKENV=y
CONFIG_LOOPW=y
CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
@ -19,7 +18,6 @@ CONFIG_CMD_PING=y
CONFIG_CMD_SNTP=y
CONFIG_CMD_BMP=y
CONFIG_CMD_BSP=y
CONFIG_CMD_DATE=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_FAT=y
CONFIG_CMD_DIAG=y

2
configs/TQM5200_STK100_defconfig
View file

@ -10,7 +10,6 @@ CONFIG_SYS_CONSOLE_IS_IN_ENV=y
CONFIG_HUSH_PARSER=y
CONFIG_CMD_ASKENV=y
CONFIG_LOOPW=y
CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
@ -19,7 +18,6 @@ CONFIG_CMD_PING=y
CONFIG_CMD_SNTP=y
CONFIG_CMD_BMP=y
CONFIG_CMD_BSP=y
CONFIG_CMD_DATE=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_FAT=y
CONFIG_CMD_DIAG=y

2
configs/TQM5200_defconfig
View file

@ -9,7 +9,6 @@ CONFIG_SYS_CONSOLE_IS_IN_ENV=y
CONFIG_HUSH_PARSER=y
CONFIG_CMD_ASKENV=y
CONFIG_LOOPW=y
CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
@ -18,7 +17,6 @@ CONFIG_CMD_PING=y
CONFIG_CMD_SNTP=y
CONFIG_CMD_BMP=y
CONFIG_CMD_BSP=y
CONFIG_CMD_DATE=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_FAT=y
CONFIG_CMD_DIAG=y

1
configs/a4m072_defconfig
View file

@ -7,7 +7,6 @@ CONFIG_HUSH_PARSER=y
CONFIG_AUTOBOOT_KEYED=y
CONFIG_AUTOBOOT_PROMPT="autoboot in %d seconds\n"
CONFIG_AUTOBOOT_DELAY_STR="asdfg"
CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y

1
configs/ac14xx_defconfig
View file

@ -5,7 +5,6 @@ CONFIG_FIT=y
CONFIG_OF_BOARD_SETUP=y
CONFIG_SYS_PROMPT="ac14xx> "
CONFIG_CMD_ASKENV=y
CONFIG_CMD_I2C=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y

1
configs/ap_sh4a_4a_defconfig
View file

@ -13,7 +13,6 @@ CONFIG_VERSION_VARIABLE=y
# CONFIG_CMD_ENV_EXISTS is not set
# CONFIG_CMD_LOADB is not set
# CONFIG_CMD_LOADS is not set
CONFIG_CMD_I2C=y
# CONFIG_CMD_FPGA is not set
# CONFIG_CMD_ECHO is not set
# CONFIG_CMD_ITEST is not set

2
configs/apx4devkit_defconfig
View file

@ -14,14 +14,12 @@ CONFIG_HUSH_PARSER=y
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
CONFIG_CMD_MMC=y
CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
CONFIG_CMD_CACHE=y
CONFIG_CMD_DATE=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_FAT=y
CONFIG_CMD_UBI=y

1
configs/aria_defconfig
View file

@ -5,7 +5,6 @@ CONFIG_OF_BOARD_SETUP=y
CONFIG_BOOTDELAY=5
CONFIG_HUSH_PARSER=y
CONFIG_CMD_ASKENV=y
CONFIG_CMD_I2C=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y

1
configs/aspenite_defconfig
View file

@ -6,7 +6,6 @@ CONFIG_BOOTDELAY=3
CONFIG_BOARD_EARLY_INIT_F=y
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
CONFIG_CMD_I2C=y
# CONFIG_CMD_SETEXPR is not set
# CONFIG_CMD_NET is not set
# CONFIG_CMD_NFS is not set

2
configs/cam5200_defconfig
View file

@ -7,14 +7,12 @@ CONFIG_BOOTDELAY=5
CONFIG_HUSH_PARSER=y
CONFIG_CMD_ASKENV=y
CONFIG_LOOPW=y
CONFIG_CMD_I2C=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
CONFIG_CMD_SNTP=y
CONFIG_CMD_BSP=y
CONFIG_CMD_DATE=y
CONFIG_MAC_PARTITION=y
CONFIG_DOS_PARTITION=y
CONFIG_ISO_PARTITION=y

2
configs/cam5200_niosflash_defconfig
View file

@ -7,14 +7,12 @@ CONFIG_BOOTDELAY=5
CONFIG_HUSH_PARSER=y
CONFIG_CMD_ASKENV=y
CONFIG_LOOPW=y
CONFIG_CMD_I2C=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
CONFIG_CMD_SNTP=y
CONFIG_CMD_BSP=y
CONFIG_CMD_DATE=y
CONFIG_MAC_PARTITION=y
CONFIG_DOS_PARTITION=y
CONFIG_ISO_PARTITION=y

1
configs/charon_defconfig
View file

@ -9,7 +9,6 @@ CONFIG_SYS_CONSOLE_IS_IN_ENV=y
CONFIG_HUSH_PARSER=y
CONFIG_CMD_ASKENV=y
CONFIG_LOOPW=y
CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y

1
configs/cm5200_defconfig
View file

@ -6,7 +6,6 @@ CONFIG_BOOTDELAY=5
CONFIG_SILENT_CONSOLE=y
CONFIG_CMD_ASKENV=y
CONFIG_LOOPW=y
CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y

2
configs/digsy_mtc_RAMBOOT_defconfig
View file

@ -13,7 +13,6 @@ CONFIG_AUTOBOOT_PROMPT="Press SPACE to abort autoboot in %d seconds\n"
CONFIG_AUTOBOOT_DELAY_STR="d"
CONFIG_AUTOBOOT_STOP_STR=" "
CONFIG_LOOPW=y
CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
@ -21,7 +20,6 @@ CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
CONFIG_CMD_BMP=y
CONFIG_CMD_CACHE=y
CONFIG_CMD_DATE=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_FAT=y
CONFIG_CMD_DIAG=y

2
configs/digsy_mtc_defconfig
View file

@ -11,7 +11,6 @@ CONFIG_AUTOBOOT_KEYED=y
CONFIG_AUTOBOOT_PROMPT="autoboot in %d seconds\n"
CONFIG_AUTOBOOT_DELAY_STR=" "
CONFIG_LOOPW=y
CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
@ -19,7 +18,6 @@ CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
CONFIG_CMD_BMP=y
CONFIG_CMD_CACHE=y
CONFIG_CMD_DATE=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_FAT=y
CONFIG_CMD_DIAG=y

2
configs/digsy_mtc_rev5_RAMBOOT_defconfig
View file

@ -13,7 +13,6 @@ CONFIG_AUTOBOOT_PROMPT="Press SPACE to abort autoboot in %d seconds\n"
CONFIG_AUTOBOOT_DELAY_STR="d"
CONFIG_AUTOBOOT_STOP_STR=" "
CONFIG_LOOPW=y
CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
@ -21,7 +20,6 @@ CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
CONFIG_CMD_BMP=y
CONFIG_CMD_CACHE=y
CONFIG_CMD_DATE=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_FAT=y
CONFIG_CMD_DIAG=y

2
configs/digsy_mtc_rev5_defconfig
View file

@ -13,7 +13,6 @@ CONFIG_AUTOBOOT_PROMPT="Press SPACE to abort autoboot in %d seconds\n"
CONFIG_AUTOBOOT_DELAY_STR="d"
CONFIG_AUTOBOOT_STOP_STR=" "
CONFIG_LOOPW=y
CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
@ -21,7 +20,6 @@ CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
CONFIG_CMD_BMP=y
CONFIG_CMD_CACHE=y
CONFIG_CMD_DATE=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_FAT=y
CONFIG_CMD_DIAG=y

2
configs/fo300_defconfig
View file

@ -12,7 +12,6 @@ CONFIG_BOARD_EARLY_INIT_F=y
CONFIG_HUSH_PARSER=y
CONFIG_CMD_ASKENV=y
CONFIG_LOOPW=y
CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
@ -21,7 +20,6 @@ CONFIG_CMD_PING=y
CONFIG_CMD_SNTP=y
CONFIG_CMD_BMP=y
CONFIG_CMD_BSP=y
CONFIG_CMD_DATE=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_FAT=y
CONFIG_CMD_DIAG=y

1
configs/gplugd_defconfig
View file

@ -6,7 +6,6 @@ CONFIG_BOOTDELAY=3
CONFIG_BOARD_EARLY_INIT_F=y
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
# CONFIG_CMD_FPGA is not set
# CONFIG_CMD_SETEXPR is not set

2
configs/ipek01_defconfig
View file

@ -7,13 +7,11 @@ CONFIG_BOOTDELAY=5
# CONFIG_CONSOLE_MUX is not set
CONFIG_SYS_CONSOLE_IS_IN_ENV=y
CONFIG_LOOPW=y
CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
CONFIG_CMD_BMP=y
CONFIG_CMD_DATE=y
CONFIG_CMD_FAT=y
# CONFIG_MMC is not set
CONFIG_MTD_NOR_FLASH=y

1
configs/m28evk_defconfig
View file

@ -22,7 +22,6 @@ CONFIG_CMD_GREPENV=y
CONFIG_CMD_MMC=y
CONFIG_CMD_SF=y
CONFIG_CMD_SPI=y
CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
CONFIG_CMD_GPIO=y
CONFIG_CMD_DHCP=y

2
configs/mecp5123_defconfig
View file

@ -6,12 +6,10 @@ CONFIG_BOOTDELAY=5
CONFIG_BOARD_EARLY_INIT_F=y
CONFIG_HUSH_PARSER=y
CONFIG_CMD_ASKENV=y
CONFIG_CMD_I2C=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
CONFIG_CMD_DATE=y
CONFIG_CMD_FAT=y
# CONFIG_MMC is not set
CONFIG_MTD_NOR_FLASH=y

2
configs/motionpro_defconfig
View file

@ -8,12 +8,10 @@ CONFIG_AUTOBOOT_KEYED=y
CONFIG_AUTOBOOT_PROMPT="Autobooting in %d seconds, press \"<Esc><Esc>\" to stop\n"
CONFIG_AUTOBOOT_STOP_STR="\x1b\x1b"
CONFIG_CMD_ASKENV=y
CONFIG_CMD_I2C=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
CONFIG_CMD_DATE=y
CONFIG_CMD_FAT=y
CONFIG_CMD_BEDBUG=y
CONFIG_LED_STATUS=y

2
configs/mpc5121ads_defconfig
View file

@ -6,13 +6,11 @@ CONFIG_BOOTDELAY=5
CONFIG_BOARD_EARLY_INIT_F=y
CONFIG_HUSH_PARSER=y
CONFIG_CMD_ASKENV=y
CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
CONFIG_CMD_DATE=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_FAT=y
CONFIG_MAC_PARTITION=y

2
configs/mpc5121ads_rev2_defconfig
View file

@ -7,13 +7,11 @@ CONFIG_BOOTDELAY=5
CONFIG_BOARD_EARLY_INIT_F=y
CONFIG_HUSH_PARSER=y
CONFIG_CMD_ASKENV=y
CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
CONFIG_CMD_DATE=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_FAT=y
CONFIG_MAC_PARTITION=y

2
configs/pcm030_LOWBOOT_defconfig
View file

@ -4,11 +4,9 @@ CONFIG_TARGET_PCM030=y
CONFIG_OF_BOARD_SETUP=y
CONFIG_SYS_EXTRA_OPTIONS="SYS_TEXT_BASE=0xFF000000"
CONFIG_BOOTDELAY=3
CONFIG_CMD_I2C=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
CONFIG_CMD_DATE=y
# CONFIG_MMC is not set
CONFIG_MTD_NOR_FLASH=y
CONFIG_USB=y

2
configs/pcm030_defconfig
View file

@ -4,11 +4,9 @@ CONFIG_TARGET_PCM030=y
CONFIG_OF_BOARD_SETUP=y
CONFIG_BOOTDELAY=3
CONFIG_SYS_PROMPT="uboot> "
CONFIG_CMD_I2C=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
CONFIG_CMD_DATE=y
# CONFIG_MMC is not set
CONFIG_MTD_NOR_FLASH=y
CONFIG_USB=y

2
configs/pdm360ng_defconfig
View file

@ -10,13 +10,11 @@ CONFIG_SILENT_CONSOLE=y
# CONFIG_CONSOLE_MUX is not set
CONFIG_HUSH_PARSER=y
CONFIG_CMD_ASKENV=y
CONFIG_CMD_I2C=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
CONFIG_CMD_BMP=y
CONFIG_CMD_DATE=y
# CONFIG_MMC is not set
CONFIG_MTD_NOR_FLASH=y
# CONFIG_PCI is not set

1
configs/r0p7734_defconfig
View file

@ -13,7 +13,6 @@ CONFIG_VERSION_VARIABLE=y
# CONFIG_CMD_ENV_EXISTS is not set
# CONFIG_CMD_LOADB is not set
# CONFIG_CMD_LOADS is not set
CONFIG_CMD_I2C=y
# CONFIG_CMD_FPGA is not set
# CONFIG_CMD_ECHO is not set
# CONFIG_CMD_ITEST is not set

2
configs/v38b_defconfig
View file

@ -3,13 +3,11 @@ CONFIG_MPC5xxx=y
CONFIG_TARGET_V38B=y
CONFIG_BOOTDELAY=3
CONFIG_BOARD_EARLY_INIT_F=y
CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
CONFIG_CMD_DATE=y
CONFIG_CMD_FAT=y
CONFIG_CMD_DIAG=y
CONFIG_MAC_PARTITION=y

10
include/common.h
View file

@ -499,9 +499,19 @@ void reset_phy (void);
void fdc_hw_init (void);
/* $(BOARD)/eeprom.c */
#ifdef CONFIG_CMD_EEPROM
void eeprom_init (int bus);
int eeprom_read (unsigned dev_addr, unsigned offset, uchar *buffer, unsigned cnt);
int eeprom_write (unsigned dev_addr, unsigned offset, uchar *buffer, unsigned cnt);
#else
/*
* Some EEPROM code is depecated because it used the legacy I2C interface. Add
* some macros here so we don't have to touch every one of those uses
*/
#define eeprom_init(bus)
#define eeprom_read(dev_addr, offset, buffer, cnt) ((void)-ENOSYS)
#define eeprom_write(dev_addr, offset, buffer, cnt) ((void)-ENOSYS)
#endif
/*
* Set this up regardless of board

1
include/configs/M54418TWR.h
View file

@ -166,7 +166,6 @@
/* I2c */
#undef CONFIG_SYS_FSL_I2C
#undef CONFIG_HARD_I2C /* I2C with hardware support */
#undef CONFIG_SYS_I2C_SOFT /* I2C bit-banged */
/* I2C speed and slave address */
#define CONFIG_SYS_I2C_SPEED 80000

64
include/configs/TQM5200.h
View file

@ -124,8 +124,7 @@
#ifndef CONFIG_CAM5200
/* POST support */
#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \
CONFIG_SYS_POST_CPU | \
CONFIG_SYS_POST_I2C)
CONFIG_SYS_POST_CPU)
#endif
#ifdef CONFIG_POST
@ -144,7 +143,6 @@
/*
* Command line configuration.
*/
#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_JFFS2
#define CONFIG_CMD_REGINFO
@ -278,54 +276,6 @@
#define CONFIG_SYS_PCICLK_EQUALS_IPBCLK_DIV2 /* define for 66MHz speed */
#endif
/*
* I2C configuration
*/
#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
#ifdef CONFIG_TQM5200_REV100
#define CONFIG_SYS_I2C_MODULE 1 /* Select I2C module #1 for rev. 100 board */
#else
#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #2 for all other revs */
#endif
/*
* I2C clock frequency
*
* Please notice, that the resulting clock frequency could differ from the
* configured value. This is because the I2C clock is derived from system
* clock over a frequency divider with only a few divider values. U-Boot
* calculates the best approximation for CONFIG_SYS_I2C_SPEED. However the calculated
* approximation allways lies below the configured value, never above.
*/
#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
#define CONFIG_SYS_I2C_SLAVE 0x7F
/*
* EEPROM configuration for onboard EEPROM M24C32 (M24C64 should work
* also). For other EEPROMs configuration should be verified. On Mini-FAP the
* EEPROM (24C64) is on the same I2C address (but on other I2C bus), so the
* same configuration could be used.
*/
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* =32 Bytes per write */
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 20
/*
* HW-Monitor configuration on Mini-FAP
*/
#if defined (CONFIG_MINIFAP)
#define CONFIG_SYS_I2C_HWMON_ADDR 0x2C
#endif
/* List of I2C addresses to be verified by POST */
#if defined (CONFIG_MINIFAP)
#undef CONFIG_SYS_POST_I2C_ADDRS
#define CONFIG_SYS_POST_I2C_ADDRS {CONFIG_SYS_I2C_EEPROM_ADDR, \
CONFIG_SYS_I2C_HWMON_ADDR, \
CONFIG_SYS_I2C_SLAVE}
#endif
/*
* Flash configuration
*/
@ -544,18 +494,6 @@
#endif
#endif
/*
* RTC configuration
*/
#if defined (CONFIG_STK52XX) && !defined (CONFIG_STK52XX_REV100)
# define CONFIG_RTC_M41T11 1
# define CONFIG_SYS_I2C_RTC_ADDR 0x68
# define CONFIG_SYS_M41T11_BASE_YEAR 1900 /* because Linux uses the same base
year */
#else
# define CONFIG_RTC_MPC5200 1 /* use internal MPC5200 RTC */
#endif
/*
* Miscellaneous configurable options
*/

20
include/configs/a4m072.h
View file

@ -81,7 +81,6 @@
/*
* Command line configuration.
*/
#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_IDE
#if defined(CONFIG_PCI)
@ -145,25 +144,6 @@
*/
#undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
/*
* I2C configuration
*/
#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */
#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
#define CONFIG_SYS_I2C_SLAVE 0x7F
/*
* EEPROM configuration
*/
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x52 /* 1010010x */
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
#define CONFIG_SYS_EEPROM_WREN 1
#define CONFIG_SYS_EEPROM_WP GPIO_PSC2_4
/*
* Flash configuration
*/

18
include/configs/ac14xx.h
View file

@ -336,28 +336,11 @@
#define CONFIG_CMDLINE_EDITING 1 /* command line history */
/* I2C */
#define CONFIG_HARD_I2C /* I2C with hardware support */
#define CONFIG_I2C_MULTI_BUS
/* I2C speed and slave address */
#define CONFIG_SYS_I2C_SPEED 100000
#define CONFIG_SYS_I2C_SLAVE 0x7F
/*
* IIM - IC Identification Module
*/
#undef CONFIG_FSL_IIM
/*
* EEPROM configuration for Atmel AT24C01:
* 8-bit addresses, 30ms write delay, 32-Byte Page Write Mode
*/
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x52
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 30
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5
/*
* Ethernet configuration
*/
@ -384,7 +367,6 @@
#define CONFIG_LOADS_ECHO 1
#define CONFIG_SYS_LOADS_BAUD_CHANGE 1
#define CONFIG_CMD_EEPROM
#undef CONFIG_CMD_FUSE
#undef CONFIG_CMD_IDE
#define CONFIG_CMD_JFFS2

14
include/configs/ap_sh4a_4a.h
View file

@ -35,20 +35,6 @@
#define CONFIG_BITBANGMII
#define CONFIG_BITBANGMII_MULTI
/* I2C */
#define CONFIG_SH_SH7734_I2C 1
#define CONFIG_HARD_I2C 1
#define CONFIG_I2C_MULTI_BUS 1
#define CONFIG_SYS_MAX_I2C_BUS 2
#define CONFIG_SYS_I2C_MODULE 0
#define CONFIG_SYS_I2C_SPEED 400000 /* 400 kHz */
#define CONFIG_SYS_I2C_SLAVE 0x50
#define CONFIG_SH_I2C_DATA_HIGH 4
#define CONFIG_SH_I2C_DATA_LOW 5
#define CONFIG_SH_I2C_CLOCK 500000000
#define CONFIG_SH_I2C_BASE0 0xFFC70000
#define CONFIG_SH_I2C_BASE1 0xFFC71000
/* undef to save memory */
#define CONFIG_SYS_LONGHELP
/* Monitor Command Prompt */

6
include/configs/apx4devkit.h
View file

@ -79,12 +79,6 @@
#define CONFIG_USB_MAX_CONTROLLER_COUNT 1
#endif
/* RTC */
#ifdef CONFIG_CMD_DATE
#define CONFIG_RTC_PCF8563
#define CONFIG_SYS_I2C_RTC_ADDR 0x51
#endif
/* Boot Linux */
#define CONFIG_BOOTFILE "uImage"
#define CONFIG_BOOTCOMMAND "run bootcmd_nand"

21
include/configs/aria.h
View file

@ -340,31 +340,11 @@
#endif
/* I2C */
#define CONFIG_HARD_I2C /* I2C with hardware support */
#define CONFIG_I2C_MULTI_BUS
/* I2C speed and slave address */
#define CONFIG_SYS_I2C_SPEED 100000
#define CONFIG_SYS_I2C_SLAVE 0x7F
#if 0
#define CONFIG_SYS_I2C_NOPROBES {{0,0x69}} /* Don't probe these addrs */
#endif
/*
* IIM - IC Identification Module
*/
#undef CONFIG_FSL_IIM
/*
* EEPROM configuration for Atmel AT24C32A-10TQ-2.7:
* 16-bit addresses, 10ms write delay, 32-Byte Page Write Mode
*/
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5
/*
* Ethernet configuration
*/
@ -392,7 +372,6 @@
#define CONFIG_LOADS_ECHO 1
#define CONFIG_SYS_LOADS_BAUD_CHANGE 1
#define CONFIG_CMD_EEPROM
#undef CONFIG_CMD_FUSE
#undef CONFIG_CMD_IDE
#define CONFIG_CMD_JFFS2

2
include/configs/axs10x.h
View file

@ -100,7 +100,7 @@
/*
* Environment settings
*/
#define CONFIG_ENV_IS_IN_EEPROM
#define CONFIG_ENV_IS_NOWHERE
#define CONFIG_ENV_SIZE SZ_512
#define CONFIG_ENV_OFFSET 0

12
include/configs/cm5200.h
View file

@ -44,7 +44,7 @@
/*
* POST support
*/
#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | CONFIG_SYS_POST_CPU | CONFIG_SYS_POST_I2C)
#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | CONFIG_SYS_POST_CPU)
#define MPC5XXX_SRAM_POST_SIZE (MPC5XXX_SRAM_SIZE - 4)
/* List of I2C addresses to be verified by POST */
#define CONFIG_SYS_POST_I2C_ADDRS {CONFIG_SYS_I2C_SLAVE, \
@ -199,16 +199,6 @@
"2m(kernel),27904k(rootfs)," \
"-(config)"
/*
* I2C configuration
*/
#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #2 */
#define CONFIG_SYS_I2C_SPEED 40000 /* 40 kHz */
#define CONFIG_SYS_I2C_SLAVE 0x0
#define CONFIG_SYS_I2C_IO 0x38 /* PCA9554AD I2C I/O port address */
#define CONFIG_SYS_I2C_EEPROM 0x53 /* I2C EEPROM device address */
/*
* RTC configuration
*/

31
include/configs/digsy_mtc.h
View file

@ -85,7 +85,6 @@
/*
* Command line configuration.
*/
#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_IDE
#define CONFIG_CMD_IRQ
#define CONFIG_CMD_PCI
@ -205,36 +204,6 @@
#define CONFIG_BOOTCOMMAND "run mtcb_start"
/*
* I2C configuration
*/
#define CONFIG_HARD_I2C 1
#define CONFIG_SYS_I2C_MODULE 1
#define CONFIG_SYS_I2C_SPEED 100000
#define CONFIG_SYS_I2C_SLAVE 0x7F
/*
* EEPROM configuration
*/
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 70
/*
* RTC configuration
*/
#if defined(CONFIG_DIGSY_REV5)
#define CONFIG_SYS_I2C_RTC_ADDR 0x56
#define CONFIG_RTC_RV3029
/* Enable 5k Ohm trickle charge resistor */
#define CONFIG_SYS_RV3029_TCR 0x20
#else
#define CONFIG_RTC_DS1337
#define CONFIG_SYS_I2C_RTC_ADDR 0x68
#define CONFIG_SYS_DS1339_TCR_VAL 0xAB /* diode + 4k resistor */
#endif
/*
* Flash configuration
*/

1
include/configs/ids8313.h
View file

@ -165,7 +165,6 @@
#define CONFIG_TSEC2
#define CONFIG_TSEC_ENET
#define CONFIG_HARD_SPI
#define CONFIG_HARD_I2C
/*
* NOR FLASH setup

23
include/configs/ipek01.h
View file

@ -150,29 +150,6 @@
#define OF_SOC "soc5200@f0000000"
#define OF_TBCLK (bd->bi_busfreq / 4)
/*
* I2C configuration
*/
#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */
#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
#define CONFIG_SYS_I2C_SLAVE 0x7F
/*
* EEPROM configuration
*/
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x53
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
/*
* RTC configuration
*/
#define CONFIG_RTC_PCF8563
#define CONFIG_SYS_I2C_RTC_ADDR 0x51
#define CONFIG_SYS_FLASH_BASE 0xFC000000
#define CONFIG_SYS_FLASH_SIZE 0x01000000
#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + \

19
include/configs/jupiter.h
View file

@ -127,25 +127,6 @@
#define OF_STDOUT_PATH "/soc5200@f0000000/serial@2000"
#endif
#if 0
/*
* I2C configuration
*/
#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */
#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
#define CONFIG_SYS_I2C_SLAVE 0x7F
/*
* EEPROM configuration
*/
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 70
#endif
/*
* Flash configuration
*/

6
include/configs/m28evk.h
View file

@ -16,7 +16,6 @@
/* U-Boot Commands */
#define CONFIG_FAT_WRITE
#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_NAND
#define CONFIG_CMD_NAND_TRIMFFS
@ -63,11 +62,6 @@
#define CONFIG_FEC_MXC
#endif
/* EEPROM */
#ifdef CONFIG_CMD_EEPROM
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
#endif
/* RTC */
#ifdef CONFIG_CMD_DATE
/* Use the internal RTC in the MXS chip */

176
include/configs/manroland/mpc5200-common.h Normal file
View file

@ -0,0 +1,176 @@
/*
* (C) Copyright 2009
* Heiko Schocher, DENX Software Engineering, hs@denx.de.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __MANROLAND_MPC52XX__COMMON_H
#define __MANROLAND_MPC52XX__COMMON_H
/*
* High Level Configuration Options
* (easy to change)
*/
#define CONFIG_MPC5200 1 /* MPC5200 CPU */
/* ... running at 33.000000MHz */
#define CONFIG_SYS_MPC5XXX_CLKIN 33000000
#define CONFIG_HIGH_BATS 1 /* High BATs supported */
/*
* Serial console configuration
*/
#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */
#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200,\
230400 }
#if (CONFIG_SYS_TEXT_BASE == 0xFFF00000) /* Boot low */
# define CONFIG_SYS_LOWBOOT 1
#endif
/*
* IPB Bus clocking configuration.
*/
#define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
/*
* Flash configuration
*/
#define CONFIG_SYS_FLASH_BASE 0xFF800000
#define CONFIG_SYS_FLASH_SIZE 0x00800000 /* 8 MByte */
#define CONFIG_ENV_ADDR (CONFIG_SYS_TEXT_BASE+0x40000) /* second sector */
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks
(= chip selects) */
#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout [ms]*/
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout [ms]*/
#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_SYS_FLASH_EMPTY_INFO
#define CONFIG_SYS_FLASH_CFI_AMD_RESET
/*
* Environment settings
*/
#define CONFIG_ENV_IS_IN_FLASH 1
#define CONFIG_ENV_SIZE 0x4000
#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET+CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
/*
* Memory map
*/
#define CONFIG_SYS_MBAR 0xF0000000
#define CONFIG_SYS_DEFAULT_MBAR 0x80000000
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE -\
GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
#define CONFIG_SYS_SDRAM_BASE 0x00000000
#define CONFIG_SYS_SRAM_BASE 0x80100000 /* CS 1 */
#define CONFIG_SYS_DISPLAY_BASE 0x80600000 /* CS 3 */
/* Settings for XLB = 132 MHz */
#define SDRAM_DDR 1
#define SDRAM_MODE 0x018D0000
#define SDRAM_EMODE 0x40090000
#define SDRAM_CONTROL 0x714f0f00
#define SDRAM_CONFIG1 0x73722930
#define SDRAM_CONFIG2 0x47770000
#define SDRAM_TAPDELAY 0x10000000
/* Use ON-Chip SRAM until RAM will be available */
#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM
#ifdef CONFIG_POST
/* preserve space for the post_word at end of on-chip SRAM */
#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_POST_SIZE
#else
#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE
#endif
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
# define CONFIG_SYS_RAMBOOT 1
#endif
#define CONFIG_SYS_MONITOR_LEN (192 << 10)
#define CONFIG_SYS_MALLOC_LEN (512 << 10)
#define CONFIG_SYS_BOOTMAPSZ (8 << 20)
/*
* Ethernet configuration
*/
#define CONFIG_MPC5xxx_FEC 1
#define CONFIG_MPC5xxx_FEC_MII100
#define CONFIG_PHY_ADDR 0x00
#define CONFIG_MII 1
/*use Hardware WDT */
#define CONFIG_HW_WATCHDOG
#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
#if defined(CONFIG_CMD_KGDB)
# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
#endif
/*
* Various low-level settings
*/
#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI
#define CONFIG_SYS_HID0_FINAL HID0_ICE
#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE
#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE
/* 8Mbit SRAM @0x80100000 */
#define CONFIG_SYS_CS1_START CONFIG_SYS_SRAM_BASE
#define CONFIG_SYS_CS_BURST 0x00000000
#define CONFIG_SYS_CS_DEADCYCLE 0x33333333
/*-----------------------------------------------------------------------
* IDE/ATA stuff Supports IDE harddisk
*-----------------------------------------------------------------------
*/
#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */
#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
#undef CONFIG_IDE_LED /* LED for ide not supported */
#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
#define CONFIG_IDE_PREINIT 1
#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA
/* Offset for data I/O */
#define CONFIG_SYS_ATA_DATA_OFFSET (0x0060)
/* Offset for normal register accesses */
#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET)
/* Offset for alternate registers */
#define CONFIG_SYS_ATA_ALT_OFFSET (0x005C)
/* Interval between registers */
#define CONFIG_SYS_ATA_STRIDE 4
#define CONFIG_ATAPI 1
#define OF_CPU "PowerPC,5200@0"
#define OF_SOC "soc5200@f0000000"
#define OF_TBCLK (bd->bi_busfreq / 4)
#define OF_STDOUT_PATH "/soc5200@f0000000/serial@2000"
#define CONFIG_OF_IDE_FIXUP
#endif /* __MANROLAND_MPC52XX__COMMON_H */

18
include/configs/mecp5123.h
View file

@ -241,26 +241,11 @@
#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
/* I2C */
#define CONFIG_HARD_I2C /* I2C with hardware support */
#define CONFIG_I2C_MULTI_BUS
#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed */
#define CONFIG_SYS_I2C_SLAVE 0x7F /* slave address */
/*
* IIM - IC Identification Module
*/
#undef CONFIG_FSL_IIM
/*
* EEPROM configuration
*/
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* 16-bit EEPROM address */
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* Atmel: AT24C32A-10TQ-2.7 */
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* 10ms of delay */
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* 32-Byte Page Write Mode */
#define CONFIG_SYS_EEPROM_WREN /* Use EEPROM write protect */
/*
* Ethernet configuration
*/
@ -280,7 +265,7 @@
/*
* Environment
*/
#define CONFIG_ENV_IS_IN_EEPROM /* Store env in I2C EEPROM */
#define CONFIG_ENV_IS_NOWHERE /* Store env in I2C EEPROM */
#define CONFIG_ENV_SIZE 0x1000
#define CONFIG_ENV_OFFSET 0x0000 /* environment starts here */
@ -288,7 +273,6 @@
#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
#define CONFIG_CMD_REGINFO
#define CONFIG_CMD_EEPROM
#undef CONFIG_CMD_FUSE
#undef CONFIG_CMD_IDE
#define CONFIG_CMD_JFFS2

22
include/configs/motionpro.h
View file

@ -34,7 +34,6 @@
* Command line configuration.
*/
#define CONFIG_CMD_DTT
#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_IDE
#define CONFIG_CMD_IMMAP
#define CONFIG_CMD_JFFS2
@ -255,21 +254,6 @@
#define CONFIG_SYS_ATA_REG_OFFSET CONFIG_SYS_ATA_DATA_OFFSET
#define CONFIG_SYS_ATA_STRIDE 4
/*
* I2C configuration
*/
#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
#define CONFIG_SYS_I2C_MODULE 2 /* select I2C module #2 */
#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
#define CONFIG_SYS_I2C_SLAVE 0x7F
/*
* EEPROM configuration
*/
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 1 /* 2 bytes per write cycle */
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 /* 2ms/cycle + 3ms extra */
/*
* RTC configuration
*/
@ -283,12 +267,6 @@
#define ENABLE_GPIO_OUT 0x00000024
#define LED_ON 0x00000010
/*
* Temperature sensor
*/
#define CONFIG_DTT_LM75 1
#define CONFIG_DTT_SENSORS { 0x49 }
/*
* Environment settings
*/

18
include/configs/mpc5121ads.h
View file

@ -327,28 +327,11 @@
#endif
/* I2C */
#define CONFIG_HARD_I2C /* I2C with hardware support */
#define CONFIG_I2C_MULTI_BUS
#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed and slave address */
#define CONFIG_SYS_I2C_SLAVE 0x7F
#if 0
#define CONFIG_SYS_I2C_NOPROBES {{0,0x69}} /* Don't probe these addrs */
#endif
/*
* IIM - IC Identification Module
*/
#undef CONFIG_FSL_IIM
/*
* EEPROM configuration
*/
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* 16-bit EEPROM address */
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* Atmel: AT24C32A-10TQ-2.7 */
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* 10ms of delay */
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* 32-Byte Page Write Mode */
/*
* Ethernet configuration
*/
@ -396,7 +379,6 @@
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_IDE
#define CONFIG_CMD_JFFS2
#define CONFIG_CMD_REGINFO

10
include/configs/mxs.h
View file

@ -126,16 +126,6 @@
#endif
#endif
/* I2C */
#ifdef CONFIG_CMD_I2C
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_MXS
#define CONFIG_HARD_I2C
#ifndef CONFIG_SYS_I2C_SPEED
#define CONFIG_SYS_I2C_SPEED 400000
#endif
#endif
/* LCD */
#ifdef CONFIG_VIDEO
#define CONFIG_VIDEO_MXS

22
include/configs/o2dnt-common.h
View file

@ -68,7 +68,6 @@
/*
* Supported commands
*/
#define CONFIG_CMD_EEPROM
#ifdef CONFIG_PCI
#define CONFIG_CMD_PCI
#endif
@ -172,27 +171,6 @@
#define CONFIG_SYS_PCICLK_EQUALS_IPBCLK_DIV2 /* define for 66MHz speed */
#endif
/*
* I2C configuration
*/
#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
#define CONFIG_SYS_I2C_MODULE 1 /* Select I2C module #1 or #2 */
#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
#define CONFIG_SYS_I2C_SLAVE 0x7F
/*
* EEPROM configuration:
*
* O2DNT board is equiped with Ramtron FRAM device FM24CL16
* 16 Kib Ferroelectric Nonvolatile serial RAM memory
* organized as 2048 x 8 bits and addressable as eight I2C devices
* 0x50 ... 0x57 each 256 bytes in size
*
*/
#define CONFIG_SYS_I2C_FRAM
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
/*
* There is no write delay with FRAM, write operations are performed at bus
* speed. Thus, no status polling or write delay is needed.

31
include/configs/pcm030.h
View file

@ -49,7 +49,6 @@ Serial console configuration
/*
* Command line configuration.
*/
#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_JFFS2
#define CONFIG_CMD_PCI
@ -120,31 +119,6 @@ IPB Bus clocking configuration.
#define CONFIG_PCI_IO_SIZE 0x01000000
#define CONFIG_SYS_XLB_PIPELINING 1
/*---------------------------------------------------------------------------
I2C configuration
---------------------------------------------------------------------------*/
#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */
#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
#define CONFIG_SYS_I2C_SLAVE 0x7F
/*---------------------------------------------------------------------------
EEPROM CAT24WC32 configuration
---------------------------------------------------------------------------*/
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x52 /* 1010100x */
#define CONFIG_SYS_I2C_FACT_ADDR 0x52 /* EEPROM CAT24WC32 */
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* Bytes of address */
#define CONFIG_SYS_EEPROM_SIZE 2048
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 15
/*---------------------------------------------------------------------------
RTC configuration
---------------------------------------------------------------------------*/
#define RTC
#define CONFIG_RTC_PCF8563 1
#define CONFIG_SYS_I2C_RTC_ADDR 0x51
/*---------------------------------------------------------------------------
Flash configuration
---------------------------------------------------------------------------*/
@ -172,11 +146,10 @@ RTC configuration
Environment settings
---------------------------------------------------------------------------*/
/* pcm030 ships with environment is EEPROM by default */
#define CONFIG_ENV_IS_IN_EEPROM 1
#define CONFIG_ENV_IS_NOWHERE
#define CONFIG_ENV_OFFSET 0x00 /* environment starts at the */
/*beginning of the EEPROM */
#define CONFIG_ENV_SIZE CONFIG_SYS_EEPROM_SIZE
#define CONFIG_ENV_SIZE 2048
#define CONFIG_ENV_OVERWRITE 1

30
include/configs/pdm360ng.h
View file

@ -301,34 +301,11 @@
#define CONFIG_SYS_PDM360NG_COPROC_READ_DELAY 5000
#define CONFIG_SYS_PDM360NG_COPROC_BAUDRATE 38400
/*
* I2C
*/
#define CONFIG_HARD_I2C /* I2C with hardware support */
#define CONFIG_I2C_MULTI_BUS
#define CONFIG_I2C_CMD_TREE
/* I2C speed and slave address */
#define CONFIG_SYS_I2C_SPEED 100000
#define CONFIG_SYS_I2C_SLAVE 0x7F
/*
* IIM - IC Identification Module
*/
#undef CONFIG_FSL_IIM
/*
* EEPROM configuration
*/
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* 16-bit EEPROM addr */
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* ST AT24C01 */
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* 10ms of delay */
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* 16-Byte Write Mode */
/*
* MAC addr in EEPROM
*/
#define CONFIG_SYS_I2C_EEPROM_BUS_NUM 0
#define CONFIG_SYS_I2C_EEPROM_MAC_OFFSET 0x10
/*
* Enabled only to delete "ethaddr" before testing
* "ethaddr" setting from EEPROM
@ -344,12 +321,6 @@
#define CONFIG_FEC_AN_TIMEOUT 1
#define CONFIG_HAS_ETH0
/*
* Configure on-board RTC
*/
#define CONFIG_RTC_M41T62 /* use M41T00 rtc via i2c */
#define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */
/*
* Environment
*/
@ -367,7 +338,6 @@
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_REGINFO
#undef CONFIG_CMD_FUSE

14
include/configs/r0p7734.h
View file

@ -40,20 +40,6 @@
# define CONFIG_SMC911X_BASE (0x84000000)
#endif
/* I2C */
#define CONFIG_SH_SH7734_I2C 1
#define CONFIG_HARD_I2C 1
#define CONFIG_I2C_MULTI_BUS 1
#define CONFIG_SYS_MAX_I2C_BUS 2
#define CONFIG_SYS_I2C_MODULE 0
#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
#define CONFIG_SYS_I2C_SLAVE 0x50
#define CONFIG_SH_I2C_DATA_HIGH 4
#define CONFIG_SH_I2C_DATA_LOW 5
#define CONFIG_SH_I2C_CLOCK 500000000
#define CONFIG_SH_I2C_BASE0 0xFFC70000
#define CONFIG_SH_I2C_BASE1 0xFFC7100
/* undef to save memory */
#define CONFIG_SYS_LONGHELP
/* Monitor Command Prompt */

10
include/configs/s32v234evb.h
View file

@ -97,16 +97,6 @@
#define CONFIG_PHY_MICREL
#endif
#if 0 /* Disable until the I2C driver will be updated */
/* I2C Configs */
#define CONFIG_CMD_I2C
#define CONFIG_HARD_I2C
#define CONFIG_I2C_MXC
#define CONFIG_SYS_I2C_BASE I2C0_BASE_ADDR
#define CONFIG_SYS_I2C_SPEED 100000
#endif
#if 0 /* Disable until the FLASH will be implemented */
#define CONFIG_SYS_USE_NAND
#endif

21
include/configs/v38b.h
View file

@ -134,27 +134,6 @@
*/
#undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
/*
* I2C configuration
*/
#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */
#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
#define CONFIG_SYS_I2C_SLAVE 0x7F
/*
* EEPROM configuration
*/
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 70
/*
* RTC configuration
*/
#define CONFIG_SYS_I2C_RTC_ADDR 0x51
/*
* Flash configuration - use CFI driver
*/