On a 4.18-rc1 kernel the following warning is seen on i.MX51 and
i.MX53:
CPU0: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable
Select the ARM_CORTEX_A8_CVE_2017_5715 workaround for i.MX51/i.MX53
to fix the problem.
With this patch applied the kernel reports:
CPU0: Spectre v2: using BPIALL workaround
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Enable CVE-2017-5715 option to set the IBE bit. This enables kernel
workarounds necessary for the said CVE.
With this enabled, Linux reports:
CPU0: Spectre v2: using BPIALL workaround
This workaround may need to be re-applied in OS environment around low
power transition resume states where context of ACR would be lost (off-mode
etc).
Signed-off-by: Nishanth Menon <nm@ti.com>
Enable CVE_2017_5715 and since we have our own v7_arch_cp15_set_acr
function to setup the bits, we are able to override the settings.
Without this enabled, Linux kernel reports:
CPU0: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable
With this enabled, Linux kernel reports:
CPU0: Spectre v2: using ICIALLU workaround
NOTE: This by itself does not enable the workaround for CPU1 (on
OMAP5 and DRA72/AM572 SoCs) and may require additional kernel patches.
Signed-off-by: Nishanth Menon <nm@ti.com>
As recommended by Arm in [1], ACTLR[0] (Enable invalidates of BTB)
needs to be set[2] for BTB to be invalidated on ICIALLU. This needs to
be done unconditionally for Cortex-A15 processors. Provide a config
option for platforms to enable this option based on impact analysis
for products.
NOTE: This patch in itself is NOT the final solution, this requires:
a) Implementation of v7_arch_cp15_set_acr on SoCs which may not
provide direct access to ACR register.
b) Operating Systems such as Linux to provide adequate workaround in the
right locations.
c) This workaround applies to only the boot processor. It is important
to apply workaround as necessary (context-save-restore) around low
power context loss OR additional processors as necessary in either
firmware support OR elsewhere in OS.
[1] https://developer.arm.com/support/security-update
[2] http://infocenter.arm.com/help/topic/com.arm.doc.ddi0438c/BABGHIBG.html
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Cc: Andre Przywara <Andre.Przywara@arm.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Tom Rini <trini@konsulko.com>
Cc: Michael Nazzareno Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
As recommended by Arm in [1], IBE[2] has to be enabled unconditionally
for BPIALL to be functional on Cortex-A8 processors. Provide a config
option for platforms to enable this option based on impact analysis
for products.
NOTE: This patch in itself is NOT the final solution, this requires:
a) Implementation of v7_arch_cp15_set_acr on SoCs which may not
provide direct access to ACR register.
b) Operating Systems such as Linux to provide adequate workaround in the right
locations.
c) This workaround applies to only the boot processor. It is important
to apply workaround as necessary (context-save-restore) around low
power context loss OR additional processors as necessary in either
firmware support OR elsewhere in OS.
[1] https://developer.arm.com/support/security-update
[2] http://infocenter.arm.com/help/topic/com.arm.doc.ddi0344k/Bgbffjhh.html
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Cc: Andre Przywara <Andre.Przywara@arm.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Tom Rini <trini@konsulko.com>
Cc: Michael Nazzareno Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Masking clock gate, reset register bits based on the
probed controller is proper only due to the assumption
that masking should start with 0 even thought the controller
has separate PHY or shared between OTG.
unfortunately these are fixed due to lack of separate
clock, reset drivers.
Say for example EHCI1 - EHCI3 in the datasheet (EHCI0 is for the OTG)
so we need to start reg_mask 0 - 2.
This patch calculated the mask, based on the register base
so that we can get the proper bits to set with respect to
probed controller.
We even do this masking by using PHY index specifier from dt,
but dev_read_addr_size is failing for 64-bit boards.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
This patch update the USB PHY index for Allwinner H3.
Same change[1] initially sent, by 'Chen-Yu Tai' but missed
to apply due to recursive version changes on the same series.
[1] https://lists.denx.de/pipermail/u-boot/2018-January/318817.html
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
fdt_file is looking for imx6ul-geam-kit.dtb but Linux
has imx6ul-geam.dtb, since Linux skipped -kit on file name
by below commit.
"ARM: dts: imx6ul-geam: Skip suffix -kit from dts name"
(sha1: 182de5ebce71e469cfa686fcdf08c9cbe11ece97)
So, due to this mismatch U-Boot failed to pick the
proper dtb which eventually break the Linux boot.
This patch fixed this mismatch by
- renaming dts files
- update config option to use new dtb file
- update fdt_file to new dtb file name
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Now that the clock-frequency information has been moved to the
driver, more DT sync is possible.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Use the clk framework to initialize clocks from drivers that need them
instead of having hardcoded frequencies and initializations from board
code.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Introduce a basic clock driver for Amlogic Meson SoCs which supports
enabling/disabling clock gates and getting their frequency.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
cpu_cmd() is reading cpu number via simple_strtoul() which is always
unsigned type.
Platform code implementations are not expecting that nr can be negative
and there is not checking in the code for that too.
This patch is using u32 type for cpu number to make sure that platform
code get proper value range.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add option to the booti_setup() which indicates to it that the caller
requires the image to be relocated to the beginning of the RAM and
that the information whether the image can be located anywhere in RAM
at 2 MiB aligned boundary or not is to be ignored. This is useful ie.
in case the Image is wrapped in another envelope, ie. fitImage and not
relocating it but moving it would corrupt the envelope.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bin Chen <bin.chen@linaro.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-By: Bin Chen <bin.chen@linaro.org>
Add regulator nodes and pinmux settings to the SDHI3 on E3 Ebisu
and enable HS200 mode on it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Both the RAVB and SH ether driver now support parsing the PHY reset
GPIOs from both the PHY nodes and the MAC nodes, move the reset GPIOs
back into the PHY nodes to minimize DT difference between U-Boot and
Linux.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The current state of RAVB driver expects the PHY reset GPIO in the
RAVB mode, move it back from the PHY node to avoid breakage.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
When CMD_GPIO is enabled the command 'gpio status -a' can cause
a hang or reboot if GPIO banks are not enabled, because it scans
all banks. This patch enables all GPIO banks so 'gpio status -a'
can fully execute.
Signed-off-by: Adam Ford <aford173@gmail.com>
When an exception or interrupt occurs the link register (LR) may
contain the source of the exception, although we do not print the
value it may still be extracted with a debugger. When in SPL we
loop on getting and exception, but use a linking branch, which
over-writes the LR value, use a regular branch instruction here.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Follow Linux commit 10b62a2f785a (".gitignore: move *.dtb and *.dtb.S
patterns to the top-level .gitignore").
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This patch prevents from the situation where we may end up with garbage
displayed on the LCD panel.
Such situation occurs when one performs "reboot -f" in Linux and then
stop in U-boot (or observe the garbage on the screen during boot up).
To prevent from such situation - the PWM pin is configured as GPIO and set
to LOW.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
If many values differ from the defaults, overriding the full table
is simpler and more space efficient than tweaking it through
mxs_adjust_memory_params().
Signed-off-by: Mans Rullgard <mans@mansr.com>
According to the Cortex-A7 TRM, for ACTLR.SMP bit "You must ensure this bit
is set to 1 before the caches and MMU are enabled, or any cache and TLB
maintenance operations are performed".
ROM sets this bit in normal boot flow, but when in serial download mode,
it is not set.
Here we add it in u-boot as a common flow for all i.MX cortex-a7 platforms,
including mx7d, mx6ul/ull and mx7ulp.
Signed-off-by: Ye Li <ye.li@nxp.com>
[fabio: adapted to U-Boot mainline codebase and make checkpatch happy]
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Orange Pi Zero Plus is an open-source single-board computer
using the Allwinner H5 SOC.
H5 Orangepi Zero Plus has
- Quad-core Cortex-A53
- 512MB DDR3
- micrSD slot
- 16MBit SPI Nor flash
- Debug TTL UART
- 1GBit/s Ethernet (RTL8211E)
- Wifi (RTL8189FTV)
- USB 2.0 Host
- USB 2.0 OTG + power supply
The device tree file is copied from the Linux kernel 4.17.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Orange Pi R1 is an open-source single-board computer using the
Allwinner H2+ SOC.
H2+ Orange Pi R1 has
- Quad-core Cortex-A7
- 256MB DDR3
- micrSD slot
- 128MBit SPI Nor flash
- Debug TTL UART
- 100MBit/s Ethernet (H2+)
- 100MBit/s Ethernet (RTL8152B)
- Wifi (RTL8189ETV)
- USB 2.0 OTG + power supply
This board is very similar to the Orange Pi Zero.
The device tree file is copied from the Linux kernel 4.17.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Add EtherAVB PHY reset on V3M Eagle to let the AVB driver unreset the PHY.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add EtherAVB pinmux node on V3M Eagle to set the pinmux configuration.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add device tree nodes for the Renesas RPC HF/QSPI controller
to R8A77990 E3.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
There should be return value check from zynqmp_mmio_read() in
zynqmp_mmio_rawwrite() to make sure that errors are propagated properly.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
dtc is showing some warnings and this change was also done in
the Linux kernel as "Input: gpio-keys - clean up device tree binding
example"
with this fragment in commit message
"Drop #address-cells and #size-cells, which are not required by the
gpio-keys binding documentation, as button sub-nodes are not devices."
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch splits the current mini emmc configuration into emmc0
and emmc1 configurations because emmc is probed at boot time and on
systems which have only one interface mini configuration is failing on
unused interface. This patch also adds required clock node in dts and
enables CONFIG_MMC_SDHCI_ZYNQ through defconfig.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
We currently handle the UEFI runtime reset / power off case handling via
a switch statement. Compilers (gcc in my case) may opt to handle these via
jump tables which they may conveniently put into .rodata which is not part
of the runtime section, so it will be unreachable when executed.
Fix this by just converting the switch statement into an if/else statement.
It produces smaller code that is faster and also correct because we no
longer refer .rodata from efi runtime code.
Reported-by: Andreas Färber <aferber@suse.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Synchronize the Linux Device Tree for Amlogic Meson GX boards from Linux 4.17.0
This will enable USB on Amlogic Meson GXL Boards like Khadas VIM, P212 or
LibreTech-CC.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The helios4 is built on the SolidRun Armada 38x SOM.
The port os based on the ClearFog board, using information from
https://github.com/helios-4/u-boot-marvell as well as dtb input
from https://github.com/helios-4/linux-marvell
Signed-off-by: Dennis Gilmore <dennis@ausil.us>
Signed-off-by: Dennis Gilmore <dgilmore@redhat.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Added the following:
1. defconfig for LS1012AFRWY Secure boot
2. PfE Validation support
Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
FRWY-LS1012A belongs to LS1012A family with features 2 1G SGMII PFE
MAC, Micro SD, USB 3.0, DDR, QuadSPI, Audio, UART.
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
[yorks: rebase and fix SPDX tag]
[yorks: fix board/freescale/ls1012afrdm/Kconfig]
Reviewed-by: York Sun <york.sun@nxp.com>
PPA firmware and header address may vary depending upon different
boards, configure ppa firmware and header address in board specific
Kconfig.
Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com>
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The lowlevel_init function uses r4 and r6 without preserving their
values as required by the AAPCS. Use r0 and r2 instead as these
are call-clobbered.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Since commit 0e373c0ade ("spl: add SPL_RESET_SUPPORT"),
reset is supported in SPL, enable this flag for STM32F SoCs family.
This allows to remove a specific case in RCC mfd driver.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
This is a series of line cards for Allied Telesis's SBx8100 chassis
switch. The CPU block is common to the SBx81GS24a, SBx81XS6, SBx81XS16
and SBx81GT40 cards collectively referred to as SBx81LIFKW in u-boot.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The mach/config.h file would helpfully define CONFIG_SYS_I2C and
CONFIG_SYS_I2C_MVTWSI if CONFIG_CMD_I2C was defined by the board. This
conflicts with the way DM_I2C works. As a transitional measure don't
automatically define these if CONFIG_DM_I2C is defined. It should be
possible to remove this once all kirkwood boards are migrated to DM.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch shows how to enable driver model support for the LS-CHLv2 and
LS-XHL boards.
There are a couple of open questions:
- do I need the u-boot,dm-pre-reloc tags in the device tree?
- should mach/config.h define CONFIG_DM_SEQ_ALIAS?
- how can we split this patch or are there any other pending patches
which does the same and I didn't catch these.
This patch is based on the http://git.denx.de/u-boot-marvell.git (master
branch) and needs the following patches, which are still pending:
https://patchwork.ozlabs.org/patch/909618/https://patchwork.ozlabs.org/patch/909617/https://patchwork.ozlabs.org/patch/909973/
Signed-off-by: Michael Walle <michael@walle.cc>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
This switches the clearfog boards to use DM based gpio and i2c
drivers. The io expanders are configured via their device-tree
entries.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
[baruch: add DT i2c aliases]
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Some QCA988x based modules presence is not detected by the SERDES lanes,
so force this detection which will trigger the LTSSM state machine to
negotiate link.
An example of such a card is WLE900VX.
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Tested-by: Chris Packham <judge.packham@gmail.com>
Tested-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
u-boot,dm-pre-reloc was missing from pinctrl and it's
children node. causing failure to configure pin mux
before relocation.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
This undocumented function relies on arch-specific code to declare a nop
weak version. Add the weak function in common code instead to avoid having
to duplicate the same function in each arch.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
The UEFI spec mandates that unaligned memory access should be enabled if
supported by the CPU architecture.
This patch implements the function unaligned_access() to reset the aligned
access flag in the system control register (SCTLR). It is called when the
bootefi command is invoked.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
[agraf: fix SPDX identifier]
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch adds support for loading secure bitstreams on ZynqMP
platforms. The secure bitstream images has to be generated using
Xilinx bootgen tool.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Import the R8A77990 and Ebisu DTS from linux-next to get the latest
version. This makes AVB ethernet work in U-Boot since the ethernet
node is now present in DT, as well as GPIOs.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Basic support for the Renesas Ebisu board based on R-Car E3:
- Memory,
- Main crystal,
- Serial console,
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[shimoda: rebase and add SPDX-License-Identifier]
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This patch adds basic support for the Renesas R-Car E3 (R8A77990) SoC:
- PSCI
- CPU (single)
- Cache controller
- Main clocks and controller
- Interrupt controller
- Timer
- PMU
- Reset controller
- Product register
- System controller
- UART for console
Inspried by a patch by Takeshi Kihara in the BSP.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add ID and Kconfig entry for the Renesas R8A77990 E3 SoC.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
PS clock(LPD_APB_CLK) is default clock for TTC. Add this clock
entry in TTC nodes.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Card detect bit was broken on revA and it is working fine with revC
board that's why this property can be removed.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This is control board on Bitmain Antminer S9.
There are 3 board variables with 256MB, 512MB and 1024MB DDR.
DDR memory is automatically detected with using get_with using
get_ram_size().
Bitmain is using 16MB space for FPGA which is handled via
reserved-memory. Also U-Boot is allocating 16B for storing bootcounts.
Watchdog is started but never service in U-Boot.
SPL MMC is working. SPL NAND is not working because it is not supported
as of now.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Existing EEMI version is to as 1.0 (available from xilinx v2018.1
version). Update required API version to match with EEMI API version.
New PMUFW version is required for operations with programmable logic.
Signed-off-by: Rajan Vaja <rajanv@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
ZynqMP emulation platforms are no longer tested and supported that's why
remove macros and code around.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Read reset reason reg and show it in log and also save it as variable.
Clearing reset reason when it is read to show only one status
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Overriding fastboot_set_reboot_flag() in arch/arm/mach-omap2/boot-common.c
leaves it applying all boards that derive from this, not just the ones which
have support for Android bootloader flow. Move the weak function override to
the relevant board files.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Rename fb_set_reboot_flag to fastboot_set_reboot_flag so it matches
all other fastboot code in the global name space. Fix the guards around
them so that they're dependent on FASTBOOT, not just USB_FUNCTION_FASTBOOT.
Move the weak implementation of fastboot_set_reboot_flag to fb_common.c
so we can call it from non-USB fastboot code.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Ensure that when selecting FASTBOOT_FLASH you end up with a buildable
configuration. Prior to this you could select NAND without MTDPARTS
and end up with an image which (surprisingly) excluded NAND.
Also fix dependencies on FASTBOOT_GPT_NAME/FASTBOOT_MBR_NAME which require
you have EFI_PARTITION/DOS_PARTITION enabled.
Delete redundant FASTBOOT_FLASH_NAND_DEV from Kconfig - it was only ever
used as a guard and the value was ignored in all cases, we're using
FASTBOOT_FLASH_NAND as the guard now.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Separate CMD_FASTBOOT from FASTBOOT and move code and configuration to
drivers/fastboot.
Switch dependencies on FASTBOOT to USB_FUNCTION_FASTBOOT as anyone who wants
FASTBOOT before this series wants USB_FUNCTION_FASTBOOT. Split
USB_FUNCTION_FASTBOOT from FASTBOOT so they retain their existing
behaviour.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The missing clock causes serial_msm driver probe to fail.
Added a dummy node so the probe succeeds, as the clock init
currently in db820c is empty.
Fixes: 11d59fe537 ("serial: serial_msm: fail probe if settings clocks fails")
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Currently mvebu sata driver is in arch/arm/mach_mvebu directory, this
patch moves it to drivers/ata directory with renaming "sata.c" to
"ahci_mvebu.c" which is aligned to Linux.
New ahci driver's kconfig option is added as AHCI_MVEBU which selects
SCSI_AHCI and is based on AHCI.
Signed-off-by: Ken Ma <make@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Enable SDHCI interface on AP and CP0 in A80x0 DTS files
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Evan Wang <xswang@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
For pinctrl driver of mvebu, the compatible strings
supported are defined differently from Linux version.
The patch aligned the compatible string with
Linux 4.17-rc4.
Signed-off-by: Evan Wang <xswang@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Import the dts files from Linux 4.17 and enable CONFIG_OF_CONTROL.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import the dts files from Linux 4.17 and enable CONFIG_OF_CONTROL.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import the dts files from Linux 4.17 and enable CONFIG_OF_CONTROL.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import the dts files from Linux 4.17 and enable CONFIG_OF_CONTROL.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import the dts file from Linux 4.17 and enable CONFIG_OF_CONTROL.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import the dts files from Linux 4.17 and enable CONFIG_OF_CONTROL.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
orangepi-prime has usb otg routed host with either EHCI0/OHCI0
sync the same from Linux.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
orangepi-pc2 has usb otg routed host with either EHCI0/OHCI0
sync the same from Linux.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Bananapi-m2-plus has usb otg routed host with either EHCI0/OHCI0
sync the same from Linux.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Allwinner H3 have a dual-routed USB PHY0 -- routed to either OHCI/EHCI
or MUSB controller.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Allwinner PHY USB code is now part of generic-phy framework,
so drop existing legacy handling like arch/arm/mach-sunxi.c
and related code areas.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Allwinner USB PHY handling can be done through driver-model
generic-phy so add the generic-phy ops to relevant places
on host and musb sunxi driver and enable them in respective
SOC's.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Clock gating bits on H43/H5 were wrong, fix them.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
clock gating bits on a64 are different than H3_H5, so fixed
only required bits on clock_sun6i.h.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Use OTP57 and 58 for MAC address
- OTP57 = MAC address bits [31:0]
- OTP58 = MAC address bit [47:32] stored in OTP LSB's
Use manufacture information in OTP13 to OTP15 to build unique
chip id saved in env variable "serial#"
(used for USB device enumeration)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Add support of fuse command (read/write/program/sense)
on bank 0 to access to BSEC SAFMEM (4096 OTP bits).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Add a MISC driver with read and write access to BSEC IP
(Boot and Security and OTP control)
- offset 0: shadowed values
- offset 0x80000000: OTP fuse box values (SAFMEM)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
The register TAMP_BOOT_CONTEXT is already updated in
get_bootmode() in cpu.c and no need to be done
twice.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Add the needed information to enable the debug uart
to have printf before the serial driver probe
(so before probe for clock, pincontrol and reset drivers)
To enable the debug on uart 4 (default console):
+ CONFIG_DEBUG_UART=y
+ CONFIG_DEBUG_UART_STM32=y
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
This patch adds pinmux and pinctrl driver for TLMM
subsystem in snapdragon chipsets.
Currently, supporting only 8016, but implementation is
generic and 8096 can be added easily.
Driver is using the generic dt-bindings and doesn't
introduce any new bindings (yet).
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The clock and serial nodes are needed before relocation.
This patch ensures that the msm-serial driver will probe
and provide uart output before relocation.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This reverts commit 819f1e081c.
This check was introduced in order to cope with the size limitation we had
when we were still using the raw environment in MMC. However, this
introduces padding as well, which can result in an overly huge binary if
one wants to flash the environment to some other location.
Since we now have a FAT-based environment, this check is not so useful
anymore, so we can just drop it.
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Måns Rullgård <mans@mansr.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
If an exception occurs in a loaded image and the relocation offset is
unknown, it is helful to know the instructions pointed to by the
program counter. This patch adds the missing output.
A possible output is:
Code: e1c560d0 e12fff1e e120077b e12fff1e (e7f7defb)
The parentheses indicate the instruction causing the exception.
The output can be disassembled using the decodecode script provided
by the Linux kernel project.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
- The correct way to build with thumb mode is to select SYS_THUMB_BUILD
- We should be setting -march=armv7-m in arch/arm/Makefile not the
sub-config.mk file.
Signed-off-by: Tom Rini <trini@konsulko.com>
- spl_board_init is empty on smartweb so drop that function
- When CONFIG_AT91SAM9_WATCHDOG is set we do not disable the watchdog in
SPL and instead let full U-Boot handle it. Instead of an empty
function just do not call a function.
Signed-off-by: Tom Rini <trini@konsulko.com>
For booting Linux in the generic distro mechanism, cmd/pxe.c
retrieves the FDT file name from "fdtfile" environment variable.
Rename "fdt_file" to "fdtfile" for easier migration to distro boot.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Change the phy-mode property to 'internal' that means to use a built-in PHY
implemented on LD11 SoC.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add clock-names and reset-names because this node recognizes multiple
clocks and resets. ("ether", and so on, for each)
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The GIO clock/reset, another MAC clock, and the PHY clock are required
for the ethernet of Pro4 SoC.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add syscon-phy-mode property specifying a phandle of system controller
to each ethernet node.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Drop per-SoC Makefile entries and replace them with one unified entry
now that the PFC tables are gone. Shuffle the Makefile around a bit
to make it more organized.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
All the boards use new modern PFC framework, the old PFC tables
are no longer used, so remove them.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
All the boards use new modern PFC framework, the old PFC tables
are no longer used, so remove them.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
All the boards use new modern PFC framework, the old PFC tables
are no longer used, so remove them.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
All the boards use new modern PFC framework, the old PFC tables
are no longer used, so remove them.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
All the boards use new modern PFC framework, the old PFC tables
are no longer used, so remove them.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The V2H Blanche port was broken since some time. This patch updates
the V2H Blanche port to use modern frameworks, DM, DT probing, SPL
for the preloading and puts it on par with the M2 Porter board.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Remove harcoded XHCI lists and detect mode, speed based on DT.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Serial-changes: 2
- Remove also XHCI macros from hardware.h
- Remove additional new line in zcu106
Preparation for Stratix 10 enablement. In ARM64, L2 cache controller is
accessed through processor registers. So, add CONFIG_SYS_L2_PL310 switch
conditional build in order this file can by shared across other SOCFPGAs.
Signed-off-by: Chin Liang See <chin.liang.see@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Add pinmux driver support for Stratix SoC
Signed-off-by: Chin Liang See <chin.liang.see@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Add Reset Manager driver support for Stratix SoC
Signed-off-by: Chin Liang See <chin.liang.see@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Add Clock Manager driver support for Stratix SoC
Signed-off-by: Chin Liang See <chin.liang.see@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Add the base address for watchdog and firewall.
Signed-off-by: Chin Liang See <chin.liang.see@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
According to ARM Cortex-A9 MPCore TRM section 2.2 - SCU registers
Access Control register offset is 0x50.
Signed-off-by: Ben Kalo <ben.h.kalo@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Clock frequency info is required in U-Boot because info would be erased
when transition from SPL to U-Boot.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
This patch enables DDR Kconfig support for Arria 10.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Dinh Nguyen <dinguyen@kernel.org>
Add function for both multiple DRAM bank and single DRAM bank size
initialization. This common functionality could be used by every single
SOCFPGA board.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Tested-by: Ley Foon Tan <ley.foon.tan@intel.com>
Current sdram driver is only applied to gen5 device, hence it is better
to rename sdram driver to more specific name which is related to gen5
device.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
The EMAC reset and PHY mode configuration was never working on the
Arria10 SoC, fix this. This patch pulls out the common code into
misc.c and passes the SoC-specific function call in as a function
pointer.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Regenerate Altera Arria 10 SoCDK SDMMC handoff file using latest
Quartus to get the new set of clock bindings in.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Synchronize Altera Arria 10 DT sources with Linux 4.16.3 as of commit
ef8216d28a5920022cddcb694d2d75bd1f0035ca
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Sort the Makefile entries, no functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
The A10 clock manager parsed DT bindings generated by Quartus the
bsp-editor to configure the A10 clocks. Sadly, those DT bindings
changed at some point. The clock manager patch used the old ones,
this patch replaces the bindings parser with one for the new set.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Pull the serial port configuration from DT and use DM serial instead
of having the serial configuration in two places, DT and board config.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Shuffle the default Kconfig entries around so it is not such a mess.
No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
This was never used, is not used anywhere and is just in the way
by adding annoying ifdeffery. Get rid of it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
u-boot,dm-spl property is specific to U-Boot, so move it into
*u-boot.dtsi files for relevant i.MX6UL files.
This make syncing Linux dts files straight forward.
Also update the MAINTAINERS file for dts files.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
u-boot,dm-spl property is specific to U-Boot, so move it into
*u-boot.dtsi files for relevant i.MX6QDL files.
This make syncing Linux dts files straight forward.
Also update the MAINTAINERS file for dts files.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Import the dts files from Linux 4.17 and enable device tree control in
u-boot.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import the dts files from Linux 4.17 and enable CONFIG_OF_CONTROL.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import the dts files from Linux 4.17 and enable CONFIG_OF_CONTROL.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import the dts file from Linux 4.17 and enable CONFIG_OF_CONTROL.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import the dts files from Linux 4.17 and enable CONFIG_OF_CONTROL.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import the dts files from Linux 4.17 and enable CONFIG_OF_CONTROL.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import the dts files from Linux 4.17 and enable CONFIG_OF_CONTROL.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import the dts files from Linux 4.17 and enable CONFIG_OF_CONTROL.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import the dts files from Linux 4.17 and enable CONFIG_OF_CONTROL.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import the dts files from Linux 4.17 and enable CONFIG_OF_CONTROL.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
These files are taken verbatim from the Linux kernel 4.17
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The SION pin must be set for proper operation of I2C when DM is enabled.
When legacy I2C is used, this bit is set implicitly in the u-boot code:
arch/arm/include/asm/arch-mx5/iomux-mx53.h:92:
MX53_PAD_KEY_ROW3__I2C2_SDA = IOMUX_PAD(0x368, 0x040, 4 |
IOMUX_CONFIG_SION, 0x820, 0, NO_PAD_CTRL),
The Linux kernel uses similar approach with:
arch/arm/boot/dts/imx53-tqma53.dtsi:182:
MX53_PAD_KEY_ROW3__I2C2_SDA 0xc0000000
After applying this patch it is possible to have the I2C working with DM
on imx53 devices:
MX53_PAD_KEY_ROW3__I2C2_SDA (0x1ee | IMX_PAD_SION)
Signed-off-by: Lukasz Majewski <lukma@denx.de>
It makes sense to select the MP multi processor option at the same time we
select the other SMP options needed for SMP capable i.MX6 SoCs.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Also remove the #ifdef's from clock.h since the Kconfig values defaults
the to old default values in clock.h.
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move CONFIG_MX31 from mx31pdk.h to mx31pdk_defconfig and introduce
necessary Kconfig changes as well.
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This replaces TARGET_GE_B{4,6,8}50V3 with common TARGET_GE_BX50V3.
The boards are identified automatically at runtime.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
This commit adds basic support for PWM found on Allwinner A64.
It can be used for pwm_backlight driver (e.g. for Pinebook)
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Move sys_env_device_rev_get() from the ddr training code to
sys_env_lib.c (which currently resides with the serdes code). This
brings sys_env_device_rev_get() into line with sys_env_device_id_get()
and sys_env_model_get().
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
PEX_CFG_DIRECT_ACCESS was defined in ddr3_hws_hw_training_def.h despite
only being used in the serdes code. Move this definition to ctrl_pex.h
where all the other PEX defines are. Also remove the duplicate
definition of PEX_DEVICE_AND_VENDOR_ID which is already defined in
ctrl_pex.h.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This adds basic support for the Turris Mox board from CZ.NIC, which is
currently being crowdfunded on Indiegogo.
Turris Mox is as modular router based on the Armada 3720 SOC (same as
EspressoBin).
The basic module can be extended by different modules. The device tree
binary for the kernel can be dependent on which modules are connected,
and in what order. Because of this, the board specific code creates
in U-Boot a variable called module_topology, which carries this
information.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
This adds support for the CPU watchdog found on Marvell Armada 37xx
SoCs.
There are 4 counters which can be set as CPU watchdog counters.
This driver uses the second counter (ID 1, counting from 0)
(Marvell's Linux also uses second counter by default).
In the future it could be adapted to use other counters, with
definition in the device tree.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
Since now we have driver for clocks on Armada 37xx, use it to determine
SQF clock frequency for the SPI driver.
Also change the default config files for Armada 37xx devices so that
the clock driver is enabled by default, otherwise the SPI driver cannot
be enabled.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
The drivers are based on Linux driver by Gregory Clement.
The TBG clocks support only the .get_rate method.
- since setting rate is not supported, the driver computes the rates
when probing and so subsequent calls to the .get_rate method do not
read the corresponding registers again
The peripheral clocks support methods .get_rate, .enable and .disable.
- the .set_parent method theoretically could be supported on some clocks
(the parent would have to be one of the TBG clocks)
- the .set_rate method would have to try all the divider values to find
the best approximation of a given rate, and it doesn't seem like
this should be needed in U-Boot, therefore not implemented
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Lane 0 supports SGMII1 and USB3.
Lane 1 supports SGMII0 and PEX0.
Lane 2 supports SATA0 and USB3.
This is needed for Armada 37xx.
This introduces new device tree bindings. AFAIK there is currently no
driver for Armada 37xx comphy in Linux. When such a driver will be
pushed into Linux, this will need to be rewritten accordingly.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
microblaze:
- Align defconfig
zynq:
- Rework fpga initialization and cpuinfo handling
zynqmp:
- Add ZynqMP R5 support
- Wire and enable watchdog on zcu100-revC
- Setup MMU map for DDR at run time
- Show board info based on DT and cleanup IDENT_STRING
zynqmp tools:
- Add read partition support
- Add initial support for Xilinx bif format for boot.bin generation
mmc:
- Fix get_timer usage on 64bit cpus
- Add support for SD3.0 UHS mode
nand-zynq:
- Add support for 16bit buswidth
- Use address cycles from onfi params
scsi:
- convert ceva sata to UCLASS_AHCI
timer:
- Add Cadence TTC for ZynqMP r5
watchdog:
- Minor cadence driver cleanup
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlr1ldMACgkQykllyylKDCHioACghoJw6+NqsZXl8zGWRP38yZ5K
mvgAnihfOQq125mpKPZmcc5yt6wVwYIU
=8ji9
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2018.07' of git://www.denx.de/git/u-boot-microblaze
Xilinx changes for v2018.07
microblaze:
- Align defconfig
zynq:
- Rework fpga initialization and cpuinfo handling
zynqmp:
- Add ZynqMP R5 support
- Wire and enable watchdog on zcu100-revC
- Setup MMU map for DDR at run time
- Show board info based on DT and cleanup IDENT_STRING
zynqmp tools:
- Add read partition support
- Add initial support for Xilinx bif format for boot.bin generation
mmc:
- Fix get_timer usage on 64bit cpus
- Add support for SD3.0 UHS mode
nand-zynq:
- Add support for 16bit buswidth
- Use address cycles from onfi params
scsi:
- convert ceva sata to UCLASS_AHCI
timer:
- Add Cadence TTC for ZynqMP r5
watchdog:
- Minor cadence driver cleanup
Xilinx ZynqMP also contains dual Cortex R5 which can run U-Boot.
This patch is adding minimal support to get U-Boot boot.
U-Boot on R5 runs out of DDR with default configuration that's why
DDR needs to be partitioned if there is something else running on arm64.
Console is done via Cadence uart driver and the first Cadence Triple
Timer Counter is used for time.
This configuration with uart1 was tested on zcu100-revC.
U-Boot 2018.05-rc2-00021-gd058a08d907d (Apr 18 2018 - 14:11:27 +0200)
Model: Xilinx ZynqMP R5
DRAM: 512 MiB
WARNING: Caches not enabled
MMC:
In: serial@ff010000
Out: serial@ff010000
Err: serial@ff010000
Net: Net Initialization Skipped
No ethernet found.
ZynqMP r5>
There are two ways how to run this on ZynqMP.
1. Run from ZynqMP arm64
tftpb 20000000 u-boot-r5.elf
setenv autostart no && bootelf -p 20000000
cpu 4 disable && cpu 4 release 10000000 lockstep
or
cpu 4 disable && cpu 4 release 10000000 split
2. Load via jtag when directly to R5
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch fills the MMU map for DDR at run time based on information read
from Device Tree or automatically detected from static configuration.
The patch is needed because for systems which has for example 1GB of memory
but MMU map is 2GB there could be spurious accesses which was seen in past
when mapping is not fitting with actual memory installed.
Signed-off-by: Nitin Jain <nitin.jain@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enable watchdog on zcu100 to make sure if there is a bug in the u-boot
there is proper reset.
Watchdog expires and PMU fw is informed and based on setting proper
action is taken.
The patch is enabling reset-on-timeout feature and also fixing fixed
clock rate for watchdog where 100MHz is max (and also default) clock value.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch enables support zc1275 revB board. It has
SD added compared to revA. The same configuration will
work for RevC boards aswell.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Now that showing silicon version is part of the CPU
info display, let's remove checkboard().
Note that the generic show_board_info() will still
show the DT 'model' property. For instance:
U-Boot 2018.05-rc2-00025-g611b3ee0159b (Apr 19 2018 - 11:23:12 +0200)
CPU: Zynq 7z045
Silicon: v1.0
Model: Zynq ZC706 Development Board
I2C: ready
Based on patches from Ariel D'Alessandro <ariel@vanguardiasur.com.ar>,
and Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
mini configuration doesn't need to show this information.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This commit moves the FPGA descriptor definition
to mach-zynq, where it makes more sense.
Based on patches from Ariel D'Alessandro <ariel@vanguardiasur.com.ar>
and Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
In past this code was commented and was used for debug purpose.
But there is no reason not to enabled it based on macros.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
As part of the main conversion a few files were missed. These files had
additional whitespace after the '*' and before the SPDX tag and my
previous regex was too strict. This time I did a grep for all SPDX tags
and then filtered out anything that matched the correct styles.
Fixes: 83d290c56f ("SPDX: Convert all of our single license tags to Linux Kernel style")
Reported-by: Heinrich Schuchardt <xypron.debian@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
The check for having a memory node within the fdt blob is made wrong, we
fix this here.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Add some more comments describing the various PCIe ports available.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
As the AS3722 GPIO0 is also a not connected on our Apalis TK1 module
explicitly configure it to high-impedance as well.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Mask HRESET_B after cleared the the RCW_SRC, because in the workaround
we override the RCW_SRC and if HRESET_B is issued after the override
then SoC cannot find valid RCW as the RCW_SRC was overwritten and
result in hang. So we need to mask HRESET_B in case user asserts it,
and the PORESET_B should be asserted which leads to resampling of
cfg_rcw_src pins and loading of correct RCW_SRC.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Enable support for multiple loadable images in SEC firmware FIT image.
Also add example "sec_firmware_ppa.its" file.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
JR3 was getting removed from device tree only if random number
generation was successful. However, if SEC firmware is present,
JR3 should be removed from device tree node irrespective of the
random seed generation as SEC firmware reserves it for it's use.
Not removing it in case of random number generation failure causes
the kernel to crash.
Random number generation was being called twice. This is not
required. If SEC firmware is running, SIP call can be made to the SEC
firmware to get the random number. This call itself would return
failure if function is not supported. Duplicate calling of random
number generation function has been removed.
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
TZASC controller configurations are similar. Put them in a macro and
avoid code duplication.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
find_next_zero_bit() incorrectly handles cases when:
- total bitmap size < 32
- rest of bits to process
static inline int find_next_zero_bit(void *addr, int size, int offset)
{
unsigned long *p = ((unsigned long *)addr) + (offset >> 5);
unsigned long result = offset & ~31UL;
unsigned long tmp;
if (offset >= size)
return size;
size -= result;
offset &= 31UL;
if (offset) {
tmp = *(p++);
tmp |= ~0UL >> (32-offset);
if (size < 32)
[1]
goto found_first;
if (~tmp)
goto found_middle;
size -= 32;
result += 32;
}
while (size & ~31UL) {
tmp = *(p++);
if (~tmp)
goto found_middle;
result += 32;
size -= 32;
}
[2]
if (!size)
return result;
tmp = *p;
found_first:
[3] tmp |= ~0UL >> size;
^^^ algo can reach above line from from points:
[1] offset > 0 and size < 32, tmp[offset-1..0] bits set to 1
[2] size < 32 - rest of bits to process
in both cases bits to search are tmp[size-1..0], but line [3] will simply
set all tmp[31-size..0] bits to 1 and ffz(tmp) below will fail.
example: bitmap size = 16, offset = 0, bitmap is empty.
code will go through the point [2], tmp = 0x0
after line [3] => tmp = 0xFFFF and ffz(tmp) will return 16.
found_middle:
return result + ffz(tmp);
}
Fix it by correctly seting tmp[31..size] bits to 1 in the above case [3].
Fixes: 81e9fe5a29 ("arm: implement find_next_zero_bit function")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
The clock node is used by the serial driver and it's needed
before relocation.
This patch ensures that the msm-serial driver can actually
use the clock node.
Signed-off-by: Ramon Fried <ramon.fried@linaro.org>
STiH410 has 2 PHYs wired on the DWC3 IP, USB2 and USB3 PHYs.
As currently no U-boot driver is available for the USB3 PHY and to avoid
issue during DWC3 drive probe, we use DWC3 IP with only USB2 PHY
using stih410-b2260-u-boot.dtsi file.
Fixes: 2fd4242cc5 ("ubs: xhci-dwc3: Enable USB3 PHY when available")
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
The Arria10 uses slightly different boot image header than the Gen5 SoCs,
in particular the header itself contains an offset from the start of the
header to which the Arria10 jumps. This offset must not be negative, yet
the header is placed at offset 0x40 of the bootable binary. Therefore, to
jump into U-Boot, add a trampoline just past the Arria10 boot header and
point to this trampoline at fixed offset from the header generated using
the mkimage -T socfpgaimage_v1 . Note that it is not needed to jump back
to offset 0x0 of the image, it is possible to jump directly at the reset
label and save processing two instructions.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Chin Liang See <chin.liang.see@intel.com>
This driver binds and manages the following regulator of
SoC's PWR block :
- reg11
- reg18
- usb33
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Since kirkwook SPI was recently converted to DM, add compatible strings
to the SPI flash devices to make them work with the new driver.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
'commit dda0bd674481 ("arm: dra762: Add support for device package identification")'
introduces ABZ and ACD package identification.
This patch is to extend usage of "fastboot getvar cpu" for
DRA76x ABZ and ACD devices.
Helps in fixing the boot warning.
Warning: fastboot.cpu: unknown CPU rev: 123863298
on
CPU : DRA762-GP ES1.0 ABZ package
Model: TI AM5748 IDK
Board: AM574x IDK REV 1.0A
Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
When a pin is muxed to a peripheral or as a GPIO, the only
configuration that can be set is the pullup. It is too restrictive
so this patch allows to give a full configuration.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Taking into account the Amlogic Family name starts with GX, including
the GXBB, GXL and GXM SoCs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Cache maintenance procedure is same for v7A and v7R
processors. So re-use cache-cp15.c file except for
mmu parts.
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The Memory Protection Unit(MPU) allows to partition memory into regions
and set individual protection attributes for each region. In absence
of MPU a default map[1] will take effect. Add support for configuring
MPU on Cortex-R, by reusing the existing support for Cortex-M processor.
[1] http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.ddi0460d/I1002400.html
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The Cortex-R* processors are a mid-range CPUs for use in deeply-embedded,
real-time systems. It implements the ARMv7-R architecture, and includes
Thumb-2 technology for optimum code density and processing throughput.
Except for MPU(Memory Protection Unit) and few CP15 registers, most of the
features are compatible with v7 architecture. So,reuse the same armv7
folder and introduce a new config CPU_V7R in order to differentiate
from v7 based platforms.
Tested-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Certain ARM architectures like ARMv7-A, ARMv7-R has support for
enabling caches using CP15 registers. To have a common support
for all these architectures, introduce a Kconfig symbol
SYS_ARM_CACHE_CP15 that selects cache-cp15.c
Tested-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add a Kconfig entry for MMU and imply for all platforms using
cache-cp15.c containing MMU setup. Using imply instead of select so that
MMU can be disabled by defconfigs when not needed.
Tested-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Currently CPU_V7 kconfig symbol supports only ARMv7A architectures under
armv7 folder. This led to a misconception of creating separate folders
for armv7m and armv7r. There is no reason to create separate folder for
other armv7 based architectures when it can co-exist with few Kconfig
symbols.
As a first step towards a common folder, rename CPU_V7 as CPUV7A. Later
separate Kconfig symbols can be added for CPU_V7R and CPU_V7M and
can co exist in the same folder.
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Suggested-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Not all ARM V7 based cpus has VBAR for remapping
vector base address. So, update VBAR only if it available.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Currently, regmap_init_mem() takes a udevice. This requires the node
has already been associated with a device. It prevents syscon/regmap
from behaving like those in Linux.
Change the first argumenet to take a device node.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Putting zero length array at the end of struct is a common technique
to embed arbitrary length of members. There is no good reason to let
regmap_alloc_count() branch by "if (count <= 1)".
As far as I understood the code, regmap->base is an alias of
regmap->ranges[0].start, but it is not helpful but make the code
just ugly.
Rename regmap_alloc_count() to regmap_alloc() because the _count
suffix seems pointless.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: fixup cpu_info-rcar.c]
Signed-off-by: Tom Rini <trini@konsulko.com>
This function is no more used, and replaced by psci_save
which save also context id as requested by PSCI requirements.
Even if the context id is not used by Linux, it should be saved
and restored in r0 when the CPU_ON is performed.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Replace the psci_save_target_pc call by the new function
psci_save(cpu, pc,context_id)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Replace the psci_save_target_pc call by the new function
psci_save(cpu, pc,context_id)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Add PSCI v1.0 support for Linux and manage PSCI state
for each CPU (affinity 0 level) with all mandatory functions:
- PSCI_VERSION
- CPU_SUSPEND
- CPU_OFF
- CPU_ON
- AFFINITY_INFO
- SYSTEM_OFF
- SYSTEM_RESET
- PSCI_FEATURES
and 1 optional to avoid Linux warning
- MIGRATE_INFO_TYPE
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: CITOOLS <smet-aci-reviews@lists.codex.cro.st.com>
The added function psci_arch_cpu_entry() is called
during psci_cpu_entry() and can be used by arch to handle
PSCI state transition from ON_PENDING to ON.
The default weak function is empty: not behavior change.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Save and use the 3rd parameter of PSCI CPU_ON request: context_id.
The context_id parameter is only meaningful to the caller.
U-Boot PSCI preserves a copy of the value passed in this parameter.
Following wakeup from a powerdown state, U-BOOT PSCI places
this value in R0 when it first enters the OS.
NB: this context id is not (yet?) used by Linux but it is mandatory
to be PSCI compliant.
update armv7 psci functions:
- psci_save_target_pc(): keep for backward compatibility with
current platform (only save PC and force context id to 0)
=> should be removed when all platform migrate to the new API
- psci_save(): new API to use by ARMv7 platform with PSCI,
save pc (= entry_point_address) and context_id
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have multiple licenses (in
these cases, dual license) declared in the SPDX-License-Identifier tag.
In this case we change from listing "LICENSE-A LICENSE-B" or "LICENSE-A
or LICENSE-B" or "(LICENSE-A OR LICENSE-B)" to "LICENSE-A OR LICENSE-B"
as per the Linux Kernel style document. Note that parenthesis are
allowed so when they were used before we continue to use them.
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
Banana Pi BPI-M2 Berry is a quad-core mini single board computer
built with Allwinner V40 SoC. It features
- Quad Core ARM Cortex A7 CPU V40
- 1GB of RAM .
- microSD/SATA port..
- onboard WiFi and BT
- 4 USB A 2.0 ports
- 1 USB OTG port
- 1 HDMI port
- 1 audio jack
- DC power port
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
omap-common cache enabling sequence relies on cpu_init_cp15()
(inside start.S) for enabling I-caches. But cpu_init_cp15()
can be skipped if CONFIG_SKIP_LOWLEVEL_INIT is defined. So
enable I-caches if not enabled already.
Debugged-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Tested-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Pull the symbol from the boards and zap struct rmobile_sysinfo as they
are rather useless. The entire purpose of that whole machinery was to
print board name in the CONFIG_ARCH_RMOBILE_BOARD_STRING. Do that in a
far simpler and more contained manner.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Convert the symbol to Kconfig, no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The dts Makefile entries for the H3 are not ordered correctly.
Move the Nano Pi entries before the Orange Pi so they are.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This patch adds a device tree file for the H5 version of the Libre
Computer Board ALL-H3-CC. It is the same board first introduced in
commit afe2754412 ("sunxi: Add support for Libre Computer Board
ALL-H3-CC H3 ver."), with the H3 SoC replaced with the H5 SoC, and
has 4Gb DDR3 chips instead of 2Gb ones.
The device tree utilizes the common board design file for ALL-H3-CC,
providing just the model strings and SoC specifics.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This patch adds a device tree file for the H2+ version of the Libre
Computer Board ALL-H3-CC. It is the same board first introduced in
commit afe2754412 ("sunxi: Add support for Libre Computer Board
ALL-H3-CC H3 ver."), with the H3 SoC replaced with the H2+ SoC, and
has only two 2Gb DDR3 chips instead of four.
The device tree utilizes the common board design file for ALL-H3-CC,
providing just the model strings and SoC specifics.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The Libre Computer Project ALL-H3-CC has three models, all using the
same board design, but with different pin compatible SoCs and amount of
DRAM.
Currently only the H3 1GB DRAM variant is supported. To support the two
other variants, first split the original device tree into a common board
design part and an SoC specific part.
The SoC part only defines which SoC is used and model name, and includes
the SoC specific dtsi file and the common design dtsi file.
Also fix up the SPDX identifier line to use the correct comment style,
and place it on the first line.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
If CONFIG_SPL_SERIAL_SUPPORT is disabled then the build fails because
serial_init is undefined. Guard preloader_console_init() appropriately
to fix this.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
SYS_ARCH_TIMER guards the usage of the ARM Generic Timer (aka arch
timer) in U-Boot.
At the moment it is mandatory for ARMv8 and used by a few ARMv7 boards.
Add a proper Kconfig symbol to express this dependency properly,
allowing certain board configuration to later disable arch timer in case
there are any problems with it.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[tuomas: rebase + fix conflicts and resync with moveconfig & use select]
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
The default of DISTRO_DEFAULTS is messy. Using the 'imply' keyword
is equivalent and cleaner.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
As of clang-5.0, things have changed a bit. First, we cannot
automatically guess -target values as if we do not pass one with CC then
cc-option will fail. Second, to disable movt/movw relocations the
argument has become -mno-movt.
Related to the target part, we cannot use arm-none-eabi as that ends up
being too generic of an ARM target for things like say rpi_3_32b to
work.
Signed-off-by: Tom Rini <trini@konsulko.com>
We have a large number of places where while we historically referenced
gd in the code we no longer do, as well as cases where the code added
that line "just in case" during development and never dropped it.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPI
This partly involves updating code that assumes that CONFIG_SPI implies
things that are specific to the MPC8xx SPI driver. For now, just update
the CONFIG tests. This also involves reworking the default for
CONFIG_SYS_DEF_EEPROM_ADDR so that we don't set it when we cannot make a
reasonable default, as it does not cause any compile failures.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This allows using the full SPL framework on mxs devices. In this
mode, the u-boot.sb image loaded by the boot ROM contains only the
SPL which then loads U-Boot proper or a kernel in falcon mode.
Signed-off-by: Mans Rullgard <mans@mansr.com>
With full SPL enabled, the loaded image overwrites the mxs_spl_data
location. Moving it a slightly lower address fixes this.
Signed-off-by: Mans Rullgard <mans@mansr.com>
When building in Thumb mode, the linker might generate mode switching
stubs in .glue sections. Include these in the final link.
Signed-off-by: Mans Rullgard <mans@mansr.com>
The code attempts to preserve the value of LR by storing it in R12/IP
across the lowevel_init() call. However, this register is not saved
by the callee. Use a register that guaranteed to be preserved instead.
Signed-off-by: Mans Rullgard <mans@mansr.com>
With the full SPL framework enabled, lowlevel_init() is required.
Make the empty stub weak so boards can override it.
Signed-off-by: Mans Rullgard <mans@mansr.com>
The E2 Alt port was broken since some time. This patch updates
the E2 Alt port to use modern frameworks, DM, DT probing, SPL
for the preloading and puts it on par with the M2 Porter board.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The M2-N Gose port was broken since some time. This patch updates
the M2-N Gose port to use modern frameworks, DM, DT probing, SPL
for the preloading and puts it on par with the M2 Porter board.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The H2 Lager port was broken since some time. This patch updates
the H2 Lager port to use modern frameworks, DM, DT probing, SPL
for the preloading and puts it on par with the M2 Porter board.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
All rockchip SoCs can use ns16550 driver, enable it for all
and set SYS_NS16550_MEM32 for all SoCs.
Version-changes: 2
- use imply instead of select
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The MACRO has been update after:
ee14d29 rockchip: back-to-bootrom: split BACK_TO_BOOTROM for TPL/SPL
We need to update the C code for it.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
These imports are entirely unused in the entire script.
Signed-off-by: Patrick Uiterwijk <patrick@puiterwijk.org>
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Disable rk_timer as SYS timer and use DM timer instead,
so that we can get a better timer framework, the rk_timer
is going to be clean after we conver to use DM timer or
ARM arch/generic timer.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add dts node for timer3.
Because of the rockchip timer can only KNOWN "dtd_rockchip_rk3368_timer"
with OF_PLATDATA enable, so we override its compatible to
"rockchip,rk3368-timer".
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
We should a -u-boot.dtsi for those config need by U-Boot only,
and other part sync with kernel.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Now that the SD/eMMC driver does not use the clock driver in SPL,
remove u-boot,dm-pre-reloc properties to let the fdtgrep tool drop
the unnecessary nodes.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
There is no need to use zynq name as SYS_BOARD for all boards.
The patch is adding an option to change it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
CONFIG_NAND_ZYNQ selects CONFIG_SYS_NAND_SELF_INIT, so the
driver doesn't have to play any ifdef game.
Also, we can mark zynq_nand_init() as static and get rid
of the mach-specific nand.h header.
This is really a revert of:
"mtd: zynq: nand: Move board_nand_init() function to board.c"
(sha1: 310995d9f9)
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The E2 Silk port was broken since some time. This patch updates
the E2 Silk port to use modern frameworks, DM, DT probing, SPL
for the preloading and puts it on par with the M2 Porter board.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
NOTE: The port is missing support for I2C1 for DA9063 reset, since the
I2C driver needs to be converted to DM and DT probing. That's not
an issue for this patch though, since the reset was broken on Silk
since forever.
The M2 Koelsch port was broken since some time. This patch updates
the M2 Koelsch port to use modern frameworks, DM, DT probing, SPL
for the preloading and puts it on par with the M2 Porter board.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add all the appropriate i2c alias in the base socfpga dtsi and enables
the i2c node on the DE0 NANO board.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Enable the RPC QSPI driver on R8A77970 V3M Eagle and configure
the environment layout to match that used by old U-Boot.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add device tree nodes for the Renesas RPC HF/QSPI controller.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Each imx image is created by a separate sub-make and during this process
the mkimage config file is run though cpp.
The cpp output is to the same file no matter what imx image is being
created.
This means if two imx images are generated in parallel they will attempt
to independently produce the same pre-processed mkimage config file at
the same time.
Avoid the problem by making the pre-processed config file name unique
based on the imx image it will be used in. This way each image will
create a unique config file and they won't clobber each other when run
in parallel.
This should fixed the build bug referenced in b5b0e4e3 ("imximage:
Remove failure when no IVT offset is found").
Cc: Breno Lima <breno.lima@nxp.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Working with HAB on the i.MX7 we've encountered a case where a board that
successfully authenticates u-boot when booting Linux via OPTEE subsequently
fails to properly bring up the RTC.
The RTC registers live in the low-power block of the Secure Non-Volatile
Storage (SNVS) block.
The root cause of the error has been traced to the HAB handing off the
SNVS-RTC in a state where HPCOMR::NPSWA_EN = 0 in other words where the
Non-Privileged Software Access Enable bit is zero. In ordinary
circumstances this is OK since we typically do not run in TZ mode, however
when we boot via HAB and enablng TrustZone, it is required to set
HPCOMR::NPSWA_EN = 1 in order for the upstream Linux driver to have
sufficient permissions to manipulate the SNVS-LP block.
On our reference board it is the difference between Linux doing this:
root@imx7s-warp-mbl:~# dmesg | grep rtc
snvs_rtc_enable read 0x00000000 from SNVS_LPLR @ 0x00000034
snvs_rtc_enable read 0x00000021 from SNVS_LPCR @ 0x00000038
snvs_rtc_enable read 0x00000000 from SNVS_HPLR @ 0x00000000
snvs_rtc_enable read 0x80002100 from SNVS_HPCOMR @ 0x00000004
snvs_rtc 30370000.snvs:snvs-rtc-lp: rtc core: registered
30370000.snvs:snvs-rtc-lp as rtc0
snvs_rtc 30370000.snvs:snvs-rtc-lp: setting system clock to2018-04-01 00:51:04 UTC (1522543864)
and doing this:
root@imx7s-warp-mbl:~# dmesg | grep rtc
snvs_rtc_enable read 0x00000000 from SNVS_LPLR @ 0x00000034
snvs_rtc_enable read 0x00000020 from SNVS_LPCR @ 0x00000038
snvs_rtc_enable read 0x00000001 from SNVS_HPLR @ 0x00000000
snvs_rtc_enable read 0x00002020 from SNVS_HPCOMR @ 0x00000004
snvs_rtc 30370000.snvs:snvs-rtc-lp: failed to enable rtc -110
snvs_rtc: probe of 30370000.snvs:snvs-rtc-lp failed with error -110
hctosys: unable to open rtc device (rtc0)
Note bit 1 of LPCR is not set in the second case and is set in the first
case and that bit 31 of HPCOMR is set in the second case but not in the
first.
Setting NPSWA_EN in HPCOMR allows us to boot through enabling TrustZone
and continue onto the kernel. The kernel then has the necessary permissions
to set LPCR::SRTC_ENV (RTC enable in the LP command register) whereas in
contrast - in the failing case the non-privileged kernel cannot do so.
This patch adds a simple init_snvs() call which sets the permission-bit
called from soc.c for the i.MX7. It may be possible, safe and desirable to
perform this on other i.MX processors but for now this is only tested on
i.MX7 as working.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
This patch adds hab_auth_img_or_fail() a command line function that
encapsulates a common usage of authenticate and failover, namely if
authenticate image fails, then drop to BootROM USB recovery mode.
For secure-boot systems, this type of locked down behavior is important to
ensure no unsigned images can be run.
It's possible to script this logic but, when done over and over again the
environment starts get very complex and repetitive, reducing that script
repetition down to a command line function makes sense.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Utkarsh Gupta <utkarsh.gupta@nxp.com>
Cc: Breno Lima <breno.lima@nxp.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Breno Lima <breno.lima@nxp.com>
The tester registers provide a unique chip-level identifier which
get_board_serial() returns in a "struct tag_serialnr".
This patch documents the properties of the registers; in summary.
31:0 OCOTP_TESTER0 (most significant)
- FSL-wide unique, encoded LOT ID STD II/SJC CHALLENGE/ Unique ID
OCOTP_TESTER1 (least significant)
31:24
- The X-coordinate of the die location on the wafer/SJC CHALLENGE/ Unique
ID
23:16
- The Y-coordinate of the die location on the wafer/SJC CHALLENGE/ Unique
ID
15:11
- The wafer number of the wafer on which the device was fabricated/SJC
CHALLENGE/ Unique ID
10:0
- FSL-wide unique, encoded LOT ID STD II/SJC CHALLENGE/ Unique ID
The 64 bits of data generate a unique serial number per-chip.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Currently when we define CONFIG_SERIAL_TAG we will barf with a failure to
define "struct tag_serialnr".
This structure is defined in <asm/setup.h>, this patch includes
<asm/setup.h> to fix.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
When the DDR calibration is enabled, a situation may happen that it
will fail on a few select boards out of a whole production lot. In
particular, after the first write leveling stage, the MPWLDECTRLx
registers will contain a value 0x1nn , for nn usually being 0x7f or
slightly lower.
What this means is that the HW write leveling detected that the DQS
rising edge on one or more bundles arrives slightly _after_ CLK and
therefore when the DDR DRAM samples CLK on the DQS rising edge, the
CLK signal is already high (cfr. AN4467 rev2 Figure 7 on page 18).
The HW write leveling then ends up adding almost an entire cycle (thus
the 0x17f) to the DQS delay, which indeed aligns it, but also triggers
subsequent calibration failure in DQS gating due to this massive offset.
There are two observations here:
- If the MPWLDECTRLx value is corrected from 0x17f to 0x0 , then the
DQS gating passes, the entire calibration passes as well and the
DRAM is perfectly stable even under massive load.
- When using the NXP DRAM calibrator for iMX6/7, the value 0x17f or so
in MPWLDECTRx register is not there, but it is replaced by 0x0 as one
would expect.
Someone from NXP finally explains why, quoting [1]:
"
Having said all that, the DDR Stress Test does something that we
do not advertise to the users. The Stress Test iself looks at the
values of the MPWLDECTRL0/1 fields before reporting results, and
if it sees any filed with a value greater than 200/256 delay
(reported as half-cycle = 0x1 and ABS_OFFSET > 0x48), the DDR
Stress test will reset the Write Leveling delay for this lane
to 0x000 and not report it in the log.
The reason that the DDR Stress test does this is because a delay
of more than 78% a clock cycle means that the DQS edge is arriving
within the JEDEC tolerence of 25% of the clock edge. In most cases,
DQS is arriving < 5% tCK of the SDCLK edge in the early case, and
it does not make sense to delay the DQS strobe almost a full clock
cycle and add extra latency to each Write burst just to make the
two edges align exactly. In this case, we are guilty of making a
decision for the customer without telling them we are doing it so
that we don't have to provide the above explanation to every customer.
They don't need to know it.
"
This patch adds the correction described above, that is if the MPWLDECTRx
value is over 0x148, the value is corrected back to 0x0.
[1] https://community.nxp.com/thread/456246
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Eric Nelson <eric@nelint.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
There is currently no use for building the SPL anymore, since the
SPI loader can easily be replaced by TPL and TPL does load U-Boot
directly. Upgrade TPL to SPL and replace what used to be SPL with
it. This way we build the U-Boot sources only twice, not thrice.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Shrink the TPL by using tiny printf and tiny memset by default.
This removes the biggest symbol -- vsnprintf_internal -- from
the TPL and reduces the text segment by about 2 kiB.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The H2 Stout port was broken since some time. This patch updates
the H2 Stout port to use modern frameworks, DM, DT probing, SPL
and TPL for the preloading and puts it on par with the M2 Porter
board.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The H2 Stout uses SCIFA0 for serial console, make sure it is
available very early on when probing from DT.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Without armv8_setup_psci register VBAR_EL3 is not set up property which
makes SMC calls jump to invalid location.
smp_kick_all_cpus is required to make slave cpus leave gic_wait_for_interrupt.
Without this they will never pursue booting process.
Fix was applied to the two ways of booting VxWorks: bootvx and bootm commands.
This implementation is very similar to what is done in boot_jump_linux
in arch/arm/lib/bootm.c file.
Tested on VxWorks 7 release SR0520 2017-12-08 Intel Stratix 10 SX SoC
Development Kit board.
Signed-off-by: Vasyl Vavrychuk <vasyl.vavrychuk@globallogic.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Fix up the memory map on Gen3 to match datasheet properly.
This simplifies the memory map setup as well, since we do
no longer need this massive complexity.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add JTAG recovery support into the M2 Porter TPL. This allows the
TPL to be loaded over JTAG, initialize the system, wait for the
JTAG debugger to load U-Boot image into RAM and then resume and
start U-Boot from RAM.
The procedure is as follows:
1) Load u-boot-tpl.bin to 0xe6300000
2) Write magic number 0x1337c0de to 0xe6300020
TPL checks for this particular magic and starts JTAG recovery
if this number is present. This is not present by default.
3) Start U-Boot TPL from 0xe6300000
4) Wait for a message from TPL on UART indicating JTAG boot:
"JTAG boot detected!"
5) Halt the system in JTAG debugger
6) Load U-Boot image (u-boot.img) to 0x4fffffc0
7) Write magic number 0xb33fc0de to 0xe6300024
TPL checks for this particular magic to verify that the U-Boot
image was loaded into DRAM by the JTAG debugger.
8) Resume the system in JTAG debugger
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add and enable TPL on M2 Porter. The TPL must fit into 16 kiB due
to the Gen2 BootROM restriction. The TPL is running from MERAM and
is capable of performing the initial initialization of PFC, Clock,
GPIO, LBSC, DBSC and QSPI NOR. DBSC is responsible for bringing up
the DDR DRAM access. The TPL is capable of loading the next stage,
U-Boot, from either SPI NOR or UART as a fallback. If either does
provide a valid U-Boot uImage, the system stops, which allows the
operator to load U-Boot ie. via JTAG and start it manually.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Skip the cache initialization, which can be done later on in U-Boot
proper, since this interferes with early DRAM initialization in TPL.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The tiny variants of memset and memcpy implementations can be
built for TPL as well, check whether a TPL build is in progress
and avoid including the default variants.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Similarly to ARMV7, on ARMV7M instruction cache memory needs
to be disabled before running linux kernel to avoid kernel to
be stuck.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Highlights this time around:
- Lots of minor spec compliance fixes
- Support full range of GOP BLT commands
- More fine grained error checking
- Network fixes (init, DP)
- Lots of other bug fixes...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=fzbe
-----END PGP SIGNATURE-----
Merge tag 'signed-efi-next' of git://github.com/agraf/u-boot
Patch queue for efi - 2018-04-09
Highlights this time around:
- Lots of minor spec compliance fixes
- Support full range of GOP BLT commands
- More fine grained error checking
- Network fixes (init, DP)
- Lots of other bug fixes...
Add support for zc12xx boards. All of them are internal boards for
silicon validation and share very similar base platforms.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This part hasn't been pushed to mainline yet that's why remove it.
The patch can be reverted in future when this is pushed there.
Reported-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
