Tegra U-Boot ensures that board_get_usable_ram_top() never returns a value
over 4GB, since some peripherals can't access such addresses. However, on
systems with more than 2GB of RAM, RAM bank 1 does describe this extra
RAM, so that Linux (or whatever OS) can use it, subject to DMA
limitations. Since board_get_usable_ram_top() points at the top of RAM
bank 0, the memory locations describes by RAM bank 1 are not mapped by
U-Boot's MMU configuration, and so cannot be used for anything.
For some completely inexplicable reason, U-Boot's EFI support ignores the
value returned by board_get_usable_ram_top(), and EFI memory allocation
routines will return values above U-Boot's RAM top. This causes U-Boot to
crash when it accesses that RAM, since it isn't mapped by the MMU. One
use-case where this happens is TFTP download of a file on Jetson TX1
(p2371-2180).
This change explicitly tells the EFI code that this extra RAM should not
be used, thus avoiding the crash.
A previous attempt to make EFI honor board_get_usable_ram_top() was
rejected. So, this patch will need to be replicated for any board that
implements board_get_usable_ram_top().
Fixes: aa909462d0 ("efi_loader: efi_allocate_pages is too restrictive")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Use CONFIG_IS_ENABLED(EFI_LOADER) to avoid explicitly checking CONFIG_SPL
too. This simplifies the conditional.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
If PCIe Mox module is connected we want to have PCIe node enabled
in U-Boot's device tree.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
Remove smi_pins definition since it is already in armada-37xx.dtsi.
Add assigned-clocks definitions to spi0.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
The bootROM in the Armada-38x (and similar) SoC has two modes for UART
boot. The first is when the normal boot media is blank (or otherwise
missing the kwb header). The second is when the boot sequence has been
interrupted with the magic byte sequence on the UART lines.
In the first mode the bootROM routine and error code register will
indicate that there was an error booting from the configured media in
bits 7:0. In the second mode there is no error to indicate but the boot
source is provided via bits 31:28.
Handle both situations so that kwboot can be used for both boot
strapping a blank board and for intercepting a regular boot sequence.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Signed-off-by: Stefan Roese <sr@denx.de>
This reverts commit e83e2b3900. This
prevents kwboot from overriding the hardware strapped boot source.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Detect the SD/eMMC boot device at run-time. Load the environment from
the boot deice, as well as save to it.
Leave the environment offset the same as in the SPI flash.
Make SD/eMMC 0 the default environment device when the boot device is
not detected.
Cc: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
Incorrect type of size variable results in 0 being
returned for sdram sizes greater than or equal to
4GB.
Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
just try to bring up an imx6ull board with console
on uart5 and found, that input_val for pin
MX6UL_PAD_UART5_RX_DATA__UART5_DCE_RX is 7 and
not 5 on imx6ull.
With this patch rx works now.
Signed-off-by: Heiko Schocher <hs@denx.de>
There are two versions of imx6ul pico SOMs: one with 256MB and another
one with 512MB of RAM.
Convert to SPL so that both versions can be supported. This patch
doesn't rework the clock initialization to avoid changing the behavior
in this same patch, so it will be cleaned up in future.
Currently only the 256MB is tested/supported.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
With DM enabled, this patch enables DM_SERIAL and removes
the NS16550 initialization from da850_lowlevel since the driver
will take care of that itself.
Signed-off-by: Adam Ford <aford173@gmail.com>
boot-common.c checks to see if I2C is enabled in SPL, but
it doens't check for DM_I2C before initializing it. This
will now only initialize the I2C is the DM_I2C is not enabled
to avoid initializing it more than once.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With the re-sync from Linux 4.18, several entries in
da850-evm-u-boot.dtsi are no longer necessary, so this patch
removes them.
Signed-off-by: Adam Ford <aford173@gmail.com>
Add the minimum dt nodes required to boot. These nodes
will get deleted as kernel gets these nodes added in the
main dts files.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add initial support for AM654 based EVM running on A53. Enable
4GB of DDR available on the EVM so that kernel DTB file
can be updated accordingly.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[Andreas: Added 4GB ddr support]
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
As no gpio.h is defined in arch/arm/mach-k3/include/,
to avoid compilation failure, do not include asm/arch/gpio.h.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Update Makefile to generate
- tispl.bin: First stage bootloader on ARMv8 core
- u-boot.img: Second stage bootloader on ARMv8 core.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
By default the device control module registers are locked,
preventing any writes to its registers.
Unlock those registers as part of the init flow.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
AM654 allows for booting from primary or backup boot media.
Both media can be chosen individually based on switch settings.
ROM looks for a valid image in primary boot media, if not found
then looks in backup boot media. In order to pass this boot media
information to boot loader, ROM stores a value at a particular
address. Add support for reading this information and determining
the boot media correctly.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
On K3 family SoCs, once the ROM loads image on R5, M3 resets R5 and
expects to start executing from 0x0. In order to handle this ROM
updates the boot vector of R5 such that first 64 bytes of image load
address are mapped to 0x0.
In this case, it is SPL's responsibility to jump to the proper image
location. So, update the PC with address of reset vector(like how
other exception vectors are handled), instead of branching to reset.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The AM654 device is designed for industrial automation and PLC
controller class platforms among other applications. Introduce
base support for AM654 SoC.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The MIO clock is enabled by default, and the STDMAC clock is
enabled by the clk driver. The ad-hoc way to enable the clock
is no longer needed.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
There are multiple GPIOs that can be used with the same driver depending
on the CONFIG_GPIO_BASE defined in the controller driver.
GPIO3 and 4 require a clock to be enabled so let's enable them when the
driver is built.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Add support for loading U-Boot on the Broadcom 7260 SoC. This port
assumes Broadcom's BOLT bootloader is acting as the second stage
bootloader, and U-Boot is acting as the third stage bootloader, loaded
as an ELF program by BOLT.
Signed-off-by: Thomas Fitzsimmons <fitzsim@fitzsim.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Four different boards had different options for enabling cache
that were virtually all the same. This consolidates these
common functions into arch/arm/cpu/arm926ejs/cache.c
This also has the positive side-effect of enabling cache on
the Davinci (da850) boards.
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Add mach-at91 to the list of consolidations]
Signed-off-by: Tom Rini <trini@konsulko.com>
This commit fixes various devicetree warnings in the at91 devicetrees
like:
arch/arm/dts/sama5d36ek_cmp.dtb: Warning (avoid_unnecessary_addr_size): /gpio_keys: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
These warnings make buildman report failed builds for most of at91 boards.
Thus, fixing it.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
For at91family, makefile was building unwanted DTBs
Moved them under specific target configuration.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
All architectures have the same definition for s8/16/32/64
and u8/16/32/64.
Factor out the duplicated code into <asm-generic/int-ll64.h>.
BTW, Linux unified the kernel space definition into int-ll64.h
a few years ago as you see in Linux commit 0c79a8e29b5f
("asm/types.h: Remove include/asm-generic/int-l64.h").
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
arch/arm/Makefile references armv5 for backwards compatibility with
older compilers. This patch removes those references to armv5,
since by now newer compilers are required which should have armv7
support enabled.
The Makefile also also has a list of options for mtune, but the
entry for CONFIG_CPU_V7A is empty, so this patch tunes the
CPU_V7A architecture to generic-armv7-a.
The following size changed apply to omap3_logic using GCC.
Stock
text data bss dec hex filename
50910 429 67580 118919 1d087 spl/u-boot-spl
540713 22700 327072 890485 d9675 u-boot
Without Armv5
text data bss dec hex filename
50916 429 67580 118925 1d08d spl/u-boot-spl
540719 22700 327064 890483 d9673 u-boot
mtune=generic-armv7-a
text data bss dec hex filename
50932 429 67580 118941 1d09d spl/u-boot-spl
540519 22700 327080 890299 d95bb u-boot
Signed-off-by: Adam Ford <aford173@gmail.com>
In commit a1274cc94a ("ARM: Page align secure section only when it is
executed in situ"), we used output section attributes (the "ALIGN"
keyword after the colon) to specify the alignment requirements. Using
the constant "COMMONPAGE" there was recently broken in binutils 2.31 [1].
Binutils maintainer Alan Modra suggested the former method would still
work. Since both methods achieve the same result, this patch does just
that. This fixes the "reboot after bootm" issue we've been seeing on
sunxi when booting non-secure.
[1] https://sourceware.org/bugzilla/show_bug.cgi?id=23571
Suggested-by: Alan Modra <amodra@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Jagan Teki <jagan@openedev.com>
When re-syncing the DTS files from the kernel, something caused
the MMC driver to no longer detect the MMC card. Undoing the
CD-invert appears to fix the issue.
Fixes: e6ea2390cd ("ARM: DTS: Resync LogicPD-Torpedo-37xx-devkit
with Linux 4.18-RC4")
Signed-off-by: Adam Ford <aford173@gmail.com>
This patch adds system suspend/resume support,
when linux kernel enters deep sleep mode, SoC will go
into below mode:
- CA7 platform goes into STOP mode;
- SoC goes into DSM mode;
- DDR goes into self-refresh mode;
- CPU0/SCU will be powered down.
When wake up event arrives:
- SoC DSM mdoe exits;
- CA7 platform exit STOP mode, SCU/CPU0 power up;
- Invalidate L1 cache;
- DDR exit self-refresh mode;
- Do secure monitor mode related initialization;
- Jump to linux kernel resume entry.
Belwo is the log of 1 iteration of system suspend/resume:
[ 338.824862] PM: suspend entry (deep)
[ 338.828853] PM: Syncing filesystems ... done.
[ 338.834433] Freezing user space processes ... (elapsed 0.001 seconds) done.
[ 338.842939] OOM killer disabled.
[ 338.846182] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
[ 338.869717] PM: suspend devices took 0.010 seconds
[ 338.877846] Disabling non-boot CPUs ...
[ 338.960301] Retrying again to check for CPU kill
[ 338.964953] CPU1 killed.
[ 338.968104] Enabling non-boot CPUs ...
[ 338.973598] CPU1 is up
[ 339.267155] mmc1: queuing unknown CIS tuple 0x80 (2 bytes)
[ 339.275833] mmc1: queuing unknown CIS tuple 0x80 (7 bytes)
[ 339.284158] mmc1: queuing unknown CIS tuple 0x80 (6 bytes)
[ 339.385065] PM: resume devices took 0.400 seconds
[ 339.389836] OOM killer enabled.
[ 339.392986] Restarting tasks ... done.
[ 339.398990] PM: suspend exit
The resume entry function has to initialize stack pointer before calling
C code, otherwise there will be an external abort occur, in additional,
invalidate L1 cache must be done in secure section as well, so this
patch also adds assembly code back and keep it as simple as possible.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Tested-by: Stefan Agner <stefan@agner.ch>
Add i.MX7D GPC initialization for low power mode
support like system suspend/resume from linux kernel:
- Pending IOMUXC IRQ to workaround GPC state machine issue;
- Mask all GPC interrupts for M4/C0/C1;
- Configure SCU timing;
- Configure time slot ack;
- Configure C0/C1 power up/down timing;
- Configure wakeup source mechanism;
- Disable DSM/RBC related settings.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
This patch improves cpu hotplug, previous cpu_off
implementation is NOT safe, a CPU can NOT power down
itself in runtime, it will cause system bus hang due
to pending transaction. So need to use other online
CPU to kill it when it is ready for killed.
Here use SRC parameter register and a magic number
of ~0 as handshake for killing a offline CPU,
when the online CPU checks the psci_affinity_info,
it will help kill the offline CPU according to
the magic number stored in SRC parameter register.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
The existing imx_watchdog driver is compatible with mx25 chipsets.
Add a WDOG1_BASE_ADDR define for the base address and enable the driver
in watchdog's Makefile.
To use the driver, a board must define CONFIG_IMX_WATCHDOG and
CONFIG_HW_WATCHDOG.
This fixes an issue when booting an mx25 chip via usb/serial. In this
case, the boot rom will always enable the watchdog. If u-boot is running
in interactive mode and the watchdog is not serviced, the system is
rebooted when the watchdog expires.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
