mx6slevk has a m25p32 SPI NOR flash connected to ESCSPI port.
Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
There is ES2 is a new revision to R8A7791.
This adds support this revision.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
There is ES2 is a new revision to R8A7790.
This adds support this revision.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
These functions are defined but has no prototype declaration. Add them.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Header files of R8A7790 and R8A7791 have common part of many.
This coordinates as rcar-base.h.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Make funtions static which are locally used in file
and remove the declaration from header file.
Signed-off-by: Manish Badarkhe <badarkhe.manish@gmail.com>
Ethernet driver configures the CPSW, SGMI and Phy and uses
the the Navigator APIs. The driver supports 4 Ethernet ports and
can work with only one port at a time.
Port configurations are defined in board.c.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Multicore navigator consists of Network Coprocessor (NetCP) and
Queue Manager sub system. More details on the hardware can
be obtained from the following links:-
Network Coprocessor: http://www.ti.com/lit/pdf/sprugz6
Multicore Navigator: http://www.ti.com/lit/pdf/sprugr9
Multicore navigator driver implements APIs to configure
the Queue Manager and NetCP Pkt DMA.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Acked-by: Tom Rini <trini@ti.com>
k2hk EVM is based on Texas Instruments Keystone2 Hawking/Kepler
SoC. Keystone2 SoC has ARM v7 Cortex-A15 MPCore processor. Please
refer the ti/k2hk_evm/README for details on the board, build and other
information.
This patch add support for keystone architecture and k2hk evm.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Sandeep Nair <sandeep_n@ti.com>
This patch moves the davinci i2c_defs.h file to drivers.i2c directory.
It will allow to reuse the davinci_i2c driver for TI Keystone2 SOCs.
Not used "git mv" command to move the file because small part of
it with definitions specific for Davinci SOCs has to remain in the
arch/arm/include/asm/arch-davinci.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Tom Rini <trini@ti.com>
Similar to OMAP5uEVM, PandaBoard, BeagleBoard-XM has a USB based
ethernet without MAC address embedded. So fake a MAC address following
the similar strategy used on OMAP5 and PandaBoard family.
Signed-off-by: Nishanth Menon <nm@ti.com>
introduce get_die_id() function which allows generation of
information such as fake MAC address from the processor ID code.
Signed-off-by: Nishanth Menon <nm@ti.com>
TI platforms such as OMAP5uevm, PandaBoard, use equivalent
logic to generate fake USB MAC address from device unique DIE ID.
Consolidate this to a generic location such that other TI platforms such
as BeagleBoard-XM can also use the same.
NOTE: at this point in time, I dont yet see a need for a generic dummy
ethernet MAC address creation function, but if there is a need in the
future, this can be further abstracted out.
Signed-off-by: Nishanth Menon <nm@ti.com>
The only remaining user of the custom bit manipulation function sr32()
is arch/arm/cpu/armv7/omap3/clock.c, so make it a static function in
that file to prepare complete removal.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Use smaller fields in the Tegra pinmux structures in order to pack the
data tables into a smaller space. This saves around 1-3KB for the SPL
and around 3-8KB for the main build of U-Boot, depending on the board,
which SoC it uses, and how many pinmux table entries there are.
In order to pack PMUX_FUNC_* into a smaller space, don't hard-code the
values of PMUX_FUNC_RSVD* to values which require 16 bits to store them,
but instead let their values be assigned automatically, so they end up
fitting into 8 bits.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Combine the Tegra USB header file into one header file for all SoCs.
Use ifdef to account for the difference, especially Tegra20 is quite
different from newer SoCs. This avoids duplication, mainly for
Tegra30 and newer devices.
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Tom Warren <twarren@nvidia.com>
On Tegra30 and later, the PTS (parallel transceiver select) and STS
(serial transceiver select) are part of the HOSTPC1_DEVLC_0 register
rather than PORTSC1_0 register. Since the reset configuration
usually matches the intended configuration, this error did not show
up on Tegra30 devices.
Also use the slightly different bit fields of first USB, (USBD) on
Tegra20 and move those definitions to the Tegra20 specific header
file.
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This renames all the pinmux pins, drive groups, and functions so they
have a prefix which matches the type name. These lists are also auto-
generated using scripts that were also used to generate the kernel
pinctrl drivers. This ensures that the lists are consistent between the
two.
The entries in tegra124_pingroups[] are all updated to remove the columns
which are no longer used.
All affected code is updated to match.
There are differences in the set of drive groups. I have validated this
against the TRM. There are differences order of pin definitions in
pinmux.c; these previously had significant mismatches with the correct
order:-( I adjusted a few entries in pinmux-config-venice2.h since the
set of legal functions for some pins was updated to match the TRM.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This renames all the pinmux pins, drive groups, and functions so they
have a prefix which matches the type name. These lists are also auto-
generated using scripts that were also used to generate the kernel
pinctrl drivers. This ensures that the lists are consistent between the
two.
The entries in tegra114_pingroups[] are all updated to remove the columns
which are no longer used.
All affected code is updated to match.
This introduces a few changes to pin/group/function naming and the set of
available functions for each pin. The new values now exactly match the
TRM; the chip documentation. I adjusted a few entries in
pinmux-config-dalmore.h due to this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This renames all the pinmux pins, drive groups, and functions so they
have a prefix which matches the type name. These lists are also auto-
generated using scripts that were also used to generate the kernel
pinctrl drivers. This ensures that the lists are consistent between the
two.
The entries in tegra30_pingroups[] are all updated to remove the columns
which are no longer used.
All affected code is updated to match.
This introduces a few changes to pin/group/function naming and the set of
available functions for each pin. The new values now exactly match the
TRM; the chip documentation. I adjusted one entry in
pinmux-config-cardhu.h due to this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This renames all the Tegra20 pinmux pins and functions so they have a
prefix which matches the type name.
The entries in tegra20_pingroups[] are all updated to remove the columns
which are no longer used.
All affected code is updated to match.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Clean up the naming of pinmux-related objects:
* Refer to drive groups rather than pad groups to match the Linux kernel.
* Ensure all pinmux API types are prefixed with pmux_, values (defines)
are prefixed with PMUX_, and functions prefixed with pinmux_.
* Modify a few type names to make their content clearer.
* Minimal changes to SoC-specific .h/.c files are made so the code still
compiles. A separate per-SoC change will be made immediately following,
in order to keep individual patch size down.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Remove a few unused functions from the pinmux header. They aren't
currently used, and removing them prevents any new usage from appearing.
This will ease moving to just pinmux_config_table() and
padgrp_config_table() in the future.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Much of arch/arm/cpu/tegra*-common/pinmux.c is identical. Remove the
duplication by creating pinmux-common.c for all the identical code.
This leaves:
* arch/arm/include/asm/arch-tegra*/pinmux.h defining only the names of
the various pins/pin groups, drive groups, and mux functions.
* arch/arm/cpu/tegra*-common/pinmux.c containing only the lookup table
stating which pin groups support which mux functions.
The code in pinmux-common.c is semantically identical to that in the
various original pinmux.c, but had some consistency and cleanup fixes
applied during migration.
I removed the definition of struct pmux_tri_ctlr, since this is different
between SoCs (especially Tegra20 vs all others), and it's much simpler to
deal with this via the new REG/MUX_REG/... defines. spl.c, warmboot.c,
and warmboot_avp.c needed updates due to this, since they previously
hijacked this struct to encode the location of some non-pinmux registers.
Now, that code simply calculates these register addresses directly using
simple and obvious math. I like this method better irrespective of the
pinmux code cleanup anyway.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Tegra's "APB misc" register region contains various miscellaneous
registers and the Tegra pinmux registers. Some code that touches the
misc registers currently uses struct pmux_tri_ctlr, which is intended to
be a definition of pinmux registers, rather than struct apb_misc_pp_ctrl,
which is intended to be a definition of the miscellaneous registers.
Convert all such code to use struct apb_misc_pp_ctrl, since struct
pmux_tri_ctlr goes away in the next patch.
This requires adding a missing field definition to struct
apb_misc_pp_ctrl, and moving the header into a more common location.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
pinmux_init() is a board-level function, not a pinmux driver function.
Move the prototype to a board header rather than the driver header.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
For consistency with other SoCs, modify Tegra20's enum pmux_func to:
* Remove PMUX_FUNC values that aren't real
* Use the same PMUX_FUNC_RSVD[1-4] values, and ensure (RSVD1 & 3)==0;
this will be assumed by pinmux_set_func() in a future patch.
Unfortunately, PMUX_FUNC_RSVD is still used in the pin macros. Use a
private define inside the driver to prevent this from causing compilaton
errors. This will be cleaned up when the pin tables are re-written in a
later patch in this series.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This field isn't used anywhere, so remove it. Note that PIN() macros are
left unchanged for now, to avoid many diffs to them; later commits will
completely rewrite them just one time.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This field isn't used anywhere, so remove it. Note that PIN() macros are
left unchanged for now, to avoid many diffs to them; later commits will
completely rewrite them just one time.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
this function is used by several board together with board_video_skip
to detect if hdmi is plugged is order to select the display to use.
So move it in imx-common to share it.
Signed-off-by: Eric Bénard <eric@eukrea.com>
this function is shared by several boards and thus can be factorized
Signed-off-by: Eric Bénard <eric@eukrea.com>
Acked-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Stefano Babic <sbabic@denx.de>
This patch add gicv3 support to uboot armv8 platform.
Changes for v2:
- rename arm/cpu/armv8/gic.S with arm/lib/gic_64.S
- move smp_kick_all_cpus() from gic.S to start.S, it would be
implementation dependent.
- Each core initialize it's own ReDistributor instead of master
initializeing all ReDistributors. This is advised by arnab.basu
<arnab.basu@freescale.com>.
Signed-off-by: David Feng <fenghua@phytium.com.cn>
This patch contains several changes required for second Ethernet
(enet1/RMII1) port on vf610
- ANADIG PLL5 control definitions required for Ethernet RMII1 clock
- Secondary Ethernet (enet1) MAC RMII1 base address definition
- RMII1 iomux definitions
- VF610_PAD_PTA6__RMII0_CLKOUT iomux definition required for
internal (e.g. crystal-less) Ethernet clocking.
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
[stefan@agner.ch: regrouped patch]
Signed-off-by: Stefan Agner <stefan@agner.ch>
The anadig_reg structure started at the wrong offset (fixed by adding
reserved_0x000[4]), was missing some reserved field required for
alignment purpose (reserved_0x094[3] between pll4_denom and pll6_ctrl)
and further contained a too short reserved field causing further miss-
alignment (reserved_0x0C4[7]). Also, rename all the reserved fields
and using a memory offset based scheme for.
Discovered and tested by temporarily putting the following debug
instrumentation into board_init():
struct anadig_reg *anadig = (struct anadig_reg *)ANADIG_BASE_ADDR;
printf("&anadig->pll3_ctrl=0x%p\n", &anadig->pll3_ctrl);
printf("&anadig->pll5_ctrl=0x%p\n", &anadig->pll5_ctrl);
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
[stefan@agner.ch: regrouped patch]
Signed-off-by: Stefan Agner <stefan@agner.ch>
When SoC first boots up, we should invalidate the cache but not flush it.
We can use the same function for invalid and flush mostly, with a wrapper.
Invalidating large cache can ben slow on emulator, so we postpone doing
so until I-cache is enabled, and before enabling D-cache.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: David Feng <fenghua@phytium.com.cn>
Clock Manager driver will be called to reconfigure all the
clocks setting based on user input. The input are passed to
Preloader through handoff files
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
CC: Pavel Machek <pavel@denx.de>
Cc: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Pavel Machek <pavel@denx.de>
Fix the macros guarding the spl.h header for various platforms. Due to
a typo and a propagation of it, the macros went out-of-sync with their
ifdef check, so fix this.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
The way that struct mmc was implemented was a bit of a mess;
configuration and internal state all jumbled up in a single structure.
On top of that the way initialization is done with mmc_register leads
to a lot of duplicated code in drivers.
Typically the initialization got something like this in every driver.
struct mmc *mmc = malloc(sizeof(struct mmc));
memset(mmc, 0, sizeof(struct mmc);
/* fill in fields of mmc struct */
/* store private data pointer */
mmc_register(mmc);
By using the new mmc_create call one just passes an mmc config struct
and an optional private data pointer like this:
struct mmc = mmc_create(&cfg, priv);
All in tree drivers have been updated to the new form, and expect
mmc_register to go away before long.
Changes since v1:
* Use calloc instead of manually calling memset.
* Mark mmc_register as deprecated.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Pull out "$(SRCTREE)/" from CONFIG_SYS_KWD_CONFIG
and push it into the top Makefile.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Michael Walle <michael@walle.cc>
Cc: Simon Guinot <simon.guinot@sequanux.org>
Cc: Dave Purdy <david.c.purdy@gmail.com>
Cc: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
Cc: Luka Perkov <luka@openwrt.org>
Cc: Valentin Longchamp <valentin.longchamp@keymile.com>
Cc: Jason Cooper <u-boot@lakedaemon.net>
Cc: Siddarth Gore <gores@marvell.com>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Eric Cooper <ecc@cmu.edu>
Cc: Suriyan Ramasami <suriyan.r@gmail.com>
This patch adds common dtsi file and config header for all
Exynos 4 based boards.
Patch additionaly adds board specific (weak) functions for
board_early_init_f and board_power_init functions.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch enables support for device tree for sdhci driver.
Non DT case is still supported.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch enables parsing mipi data from device tree.
Non device tree case is still supported.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add NAND SPL boot support with hardware PMECC.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Add SPI SPL boot support for sama5d3xek board.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Tegra124 moved the CSITE block's base address. Fix U-Boot to use
the correct address.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Register pmc_pwrgate_timer_mult has a different layout on Tegra114 and
Tegra124. Reflect this in pmc.h.
Also, simply write the whole of the register in start_cpu() rather than
doing a read-modify-write; the register is simple enough that the code
can easily construct the entire desired value.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
<asm/arch-tegra/tegra.h> needs to use CONFIG_TEGRA* to conditionalize
some definitions, since some modules moved between generations. Move
the definition of CONFIG_TEGRAnn to a header that's included earlier,
so that it's set by the time tegra.h needs to use it.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
omap_elm.h is a generic header used by OMAP ELM driver for all TI platfoms.
Hence this file should be present in generic folder instead of architecture
specific include folder.
Build tested using: ./MAKEALL -s am33xx -s omap3 -s omap4 -s omap5
Signed-off-by: Pekon Gupta <pekon@ti.com>
omap_gpmc.h is a generic header used by OMAP NAND driver for all TI platfoms.
Hence this file should be present in generic folder instead of architecture
specific include folder.
Build tested using: ./MAKEALL -s am33xx -s omap3 -s omap4 -s omap5
Signed-off-by: Pekon Gupta <pekon@ti.com>
Each SoC platform (AM33xx, OMAP3, OMAP4, OMAP5) has its own copy of GPMC related
defines and declarations scattered in SoC platform specific header files
like include/asm/arch-xx/cpu.h
However, GPMC hardware remains same across all platforms thus this patch merges
GPMC data scattered across different arch-xx specific header files into single
header file include/asm/arch/omap_gpmc.h
Build tested using: ./MAKEALL -s am33xx -s omap3 -s omap4 -s omap5
Signed-off-by: Pekon Gupta <pekon@ti.com>
OMAP NAND driver can detect Page-size and OOB-size of NAND device from ONFI
params or nand_id[] table. And based on that it defines ECC layout.
This patch
1) removes following board configs used for defining NAND ECC layout
- GPMC_NAND_ECC_LP_x16_LAYOUT (for large page x16 NAND)
- GPMC_NAND_ECC_LP_x8_LAYOUT (for large page x8 NAND)
- GPMC_NAND_ECC_SP_x16_LAYOUT (for small page x16 NAND)
- GPMC_NAND_ECC_SP_x8_LAYOUT (for small page x8 NAND)
2) removes unused #defines in common omap_gpmc.h depending on above configs
Build tested using: ./MAKEALL -s am33xx -s omap3 -s omap4 -s omap5
Signed-off-by: Pekon Gupta <pekon@ti.com>
Currently there are two sets of omap_gpmc.h header files
(a) arch/arm/include/asm/omap_gpmc.h
common header file for all platforms, containing defines and declarations used
by GPMC NAND driver.
(b) arch/arm/include/asm/arch-xx/omap_gpmc.h
SoC platform specific header file containing defines like ECC layout.
This patch removes platform specific arch-xx/omap_gpmc.c because:
- GPMC hardware engine is common for all SoC platforms hence only (a) is enough
- ECC layout is now defined in omap_nand.c driver itself based on ecc-scheme
selected. Hence all ECC layout declarations in (b) are redundant.
Build tested using: ./MAKEALL -s am33xx -s omap3 -s omap4 -s omap5
Signed-off-by: Pekon Gupta <pekon@ti.com>
Copied from Linux sources "include/linux/sizes.h" commit
413541dd66d51f791a0b169d9b9014e4f56be13c
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Tom Rini <trini@ti.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Acked-by: Tom Rini <trini@ti.com>
Acked-by: Stefan Roese <sr@denx.de>
[trini: Add bcm Kona platforms to the patch]
Signed-off-by: Tom Rini <trini@ti.com>
chip->ecc.hwctl() is used for preparing the H/W controller before read/write
NAND accesses (like assigning data-buf, enabling ECC scheme configs, etc.)
Though all ECC schemes in OMAP NAND driver use GPMC controller for generating
ECC syndrome (for both Read/Write accesses). But but in current code
HAM1_ECC and BCHx_ECC schemes implement individual function to achieve this.
This patch
(1) removes omap_hwecc_init() and omap_hwecc_init_bch()
as chip->ecc.hwctl will re-initializeGPMC before every read/write call.
omap_hwecc_init_bch() -> omap_enable_ecc_bch()
(2) merges the GPMC configuration code for all ECC schemes into
single omap_enable_hwecc(), thus adding scalability for future ECC schemes.
omap_enable_hwecc() + omap_enable_ecc_bch() -> omap_enable_hwecc()
Signed-off-by: Pekon Gupta <pekon@ti.com>
Add bcm281xx architecture support code including a clock framework and
chip reset. Define register block base addresses for the bcm281xx
architecture and create an empty gpio header file required when
CONFIG_CMD_GPIO is set.
Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Reviewed-by: Steve Rae <srae@broadcom.com>
Reviewed-by: Tim Kryger <tkryger@linaro.org>
The Kona architecture is present on a number of Broadcom mobile SoCs
including the bcm281xx family of chips.
Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Reviewed-by: Steve Rae <srae@broadcom.com>
Reviewed-by: Tim Kryger <tkryger@linaro.org>
Schematic indicates GPIO5_7 is to be used for VTT regulator control
rather than GPIO0_21 so modify enable_vtt_regulator to reflect this.
Without this some boards will experience DDR3 corruption and fail to
boot.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
[trini: Rework patch against mainline]
Signed-off-by: Tom Rini <trini@ti.com>
Adds support for Bernecker & Rainer Industrieelektronik GmbH KWB
Motherboard, using TI's AM3352 SoC.
Most of code is derived from TI's AM335x_EVM
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
Cc: trini@ti.com
This patch add support for the Silica Pengwyn board [1]
The board is based on a TI AM3354 CPU [2]
All jumpers removed it will boot from the SDcard, the console is on
UART1 accessible via the FDTI -> USB. The on board NAND flash is
supported and can act as boot medium, depending on jumper settings.
USB Host, USB Device and Ethernet are also provided but untested.
[1]
http://www.silica.com/product/silica-pengwyn-board.html
[2]
http://www.ti.com/product/am3354
Signed-off-by: Lothar Felten <lothar.felten@gmail.com>
[trini: Move CONFIG_BOARD_LATE_INIT into am335x_evm.h, drop unused
spi0_pin_mux from Pengwyn support]
Signed-off-by: Tom Rini <trini@ti.com>
Conflicts:
Makefile
drivers/net/npe/Makefile
These two conflicts arise from commit 0b2d3f20
("ARM: NET: Remove the IXP NPE ethernet driver") and are
resolved by deleting the drivers/net/npe/Makefile file
and removing the CONFIG_IXP4XX_NPE line from Makefile.
Having CONFIG_SYS_I2C_BASE requires DW I2C driver to explicitly include
<arch/hardware.h> which other platforms may not have at all.
It's always good to have a driver platform-independent.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Tom Rini <trini@ti.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Vipin Kumar <vipin.kumar@st.com>
Cc: Armando Visconti <armando.visconti@st.com>
- When CONFIG_DISPLAY_CPUINFO is not enabled,
print_cpuinfo() should be defined as an empty function
in a header, include/common.h
- Remove #ifdef CONFIG_DISPLAY_CPUINFO .. #endif
from caller, common/board_f.c and arch/arm/lib/board.c
- Remove redundant prototypes in arch/arm/lib/board.c,
arch/arm/include/asm/arch-am33x/sys_proto.h and
board/nokia/rx51/rx51.h, keeping the one in include/common.h
- Add #ifdef CONFIG_DISPLAY_CPUINFO to the func definition
where it is missing
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Add the SATA boot support for OMAP5 and dra7xx.
Renamed the omap_sata_init to the common init_sata(int dev)
for commonality in with sata stack.
Added the ROM boot device ID for SATA.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
SPL is using ps7_init.c/h files which are generated
from design tools which have to be copied to
boards/xilinx/zynq folder before compilation.
BSS section is moved to SDRAM because fat support
requires more space than SRAM size.
Added:
- MMC and QSPI support
- Boot OS directly from SPL
- Enable SPL command
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
Remove hard coded clock divider setting and use the Zynq clock framework
to dynamically calculate appropriate dividers at run time.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The GEM driver should not need to know about Zynq specific details of
RCLK related registers and bitfields in the SLCR. Move those details to
the slcr driver.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Define both serial uarts in the driver and return
default uart based on board configuration.
- Move baseaddresses to hardware.h
- Define default baudrate and clock values
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The dual lite and solo variant have only 4 SPI controller.
respect this in the MXC_SPI_BASE_ADRESSES macro
Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Provide define for the SCLK_CTL field of the config reg of ECSPI.
While at it, oder the defines to improve readability and make
adding more defines easier.
Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Currently when we boot a mx6dual U-boot reports that it is a mx6quad.
Report it as MX6D instead:
CPU: Freescale i.MX6D rev1.2 at 792 MHz
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano babic <sbabic@denx.de>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Instead of duplicating the CPU definitions at mx5 and mx6 sys_proto.h header
files, introduce a common header to centralize such definitions.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
This patch corrects the divider value written to CLKDIV register.
Since SDCLKIN is divided inside controller by the DIVRATIO value set
in the CLKSEL register, we need to use the same output clock value to
calculate the CLKDIV value.
as per user manual: cclk_in = SDCLKIN / (DIVRATIO + 1)
Input parameter to mmc_clk is changed to dwmci_host, since
we need the same to read DWMCI_CLKSEL register.
This improves the read timing values for channel 0 on SMDK5250
from 0.288sec to 0.144sec
Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
This patch adds s5p_cpu_rev.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch enables to read cpu revision on Exynos CPU.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The architecture is unmaintained and dead, remove it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Michael Schwingen <michael@schwingen.org>
Cc: Tom Rini <trini@ti.com>
These headers define the Tegra124 hardware. Add them to the usual
place.
Add Tegra124 chip ID/SKU ID definitions to common headers.
There's no real HW change on Tegra124 for 90% of the toys, so it might
make sense for a future patch to unify some of the content of these
files in a common location.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Pass just the partition ID to power_partition(), rather than also passing
the partition's status register mask too. This makes it simpler to get
call-sites correct, since they don't need to pass two different values
that define the same thing and must match.
Consequently, we can remove the mask definitions from pmc.h.
Suggested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Use a named constant for the PLL lock bit in enable_cpu_clocks().
Construct the complete value of pmc_pwrgate_toggle, rather than doing a
read-modify-write; the register is simple enough and doesn't need to
maintain state between operations.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Based on the Tegra TRM, the system clock (which is the AVP clock) can
run up to 275MHz. On power on, the default sytem clock source is set to
PLLP_OUT0. In function clock_early_init(), PLLP_OUT0 will be set to
408MHz which is beyond system clock's upper limit.
The fix is to set the system clock to CLK_M before initializing PLLP,
and then switch back to PLLP_OUT4, which has an appropriate divider
configured, after PLLP has been configured
Implement this logic in new function tegra30_set_up_pllp(),
which sets up PLLP and all PLLP_OUT* dividers, and handles the AVP
clock switching. Remove the duplicate PLLP setup from pllx_set_rate()
and adjust_pllp_out_freqs().
Signed-off-by: Jimmy Zhang <jimmzhang@nvidia.com>
[swarren, significantly refactored the change]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Tegra114 and later's PMC module removes the pwrgate_timer_on register
and replaces it with a clamp_status register. Adjust pmc.h to reflect
this, and update any code affected by the change.
The cpu.c change in this patch was extracted from a much larger patch
by Jimmy Zhang. The pmc.h change was written from scratch, but inspired
by related changes made by Tom Warren.
There could well be other differences in the PMC register set for chips
after Tegra20/30. However, they don't affect the code in U-Boot at
present, so I haven't attempted an exhaustive update of pmc.h.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Some clock sources have 3-bit muxes in bits 31:29. Implement core
support for this mux field.
Signed-off-by: Tom Warren <twarren@nvidia.com>
[swarren, extracted from a larger patch by Tom]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Since all code that sets or interprets MASK_BITS_* now uses the enums
to define/compare the values, there is no need for MASK_BITS_* to have
a specific integer value. In fact, having a specific integer value may
encourage people to hard-code those values, or interpret the values in
incorrect ways.
As such, remove the logic that assigns a specific value to the enum
values in order to make it completely clear that it's just an enum, not
something that directly represents some integer value.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
OUT_CLK_SOURCE_ are currently named after the number of bits the mask
they represent includes. However, bit count is not the only possible
variable; bit position may also vary. Rename OUT_CLK_SOURCE_ to
OUT_CLK_SOURCE_31_30_ and OUT_CLK_SOURCE4_ to OUT_CLK_SOURCE_31_28 to
more completely describe exactly what they represent, without having to
go look up the definitions.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The only place where the MASK_BITS_* values are used is in
adjust_periph_pll(), which interprets the value 4 (old MASK_BITS_29_28,
new MASK_BITS_31_28) as being associated with mask OUT_CLK_SOURCE4_MASK,
i.e. bits 31:28. Rename the MASK_BITS_ macro to reflect how it's actually
implemented.
Note that no Tegra clock register actually uses all of bits 31:28 as
the mux field. Rather, bits 30:28, 29:28, or 28 are used. However, in
those cases, nothing is stored in the bits above the mux field, so it's
safe to pretend that the mux field extends all the way to the end of the
register. As such, the U-Boot clock driver is currently a bit lazy, and
doesn't distinguish between 31:28, 30:28, 29:28 and 28; it just lumps
them all together and pretends they're all 31:28. This patch doesn't
cause this issue; it was pre-existing. Hopefully, future patches will
clean this up.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The enum used to define the set of register bits used to represent a
clock's input mux, MUX_BITS_*, is defined separately for each SoC at
present. Move this definition to a common location to ease fixing up
some issues with the definition, and the code that uses it.
Signed-off-by: Tom Warren <twarren@nvidia.com>
[swarren, extracted from a larger patch by Tom]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Old s5p gpio coding method was not clean and was not working properly
for all parts and banks. New method is clean and easy to extend.
Gpio coding mask:
0x000000ff - pin number
0x00ffff00 - bank offset
0xff000000 - part number
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add PCIe driver for the Freescale i.MX6 SoC . This driver operates the
PCIe block in RC mode only, the EP mode is NOT supported. The driver is
tested with the Intel e1000 NIC driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Split the SATA clock enabling function and add PCI express clock
enabling function. The SATA clock enabling function starts up the
100MHz SATA reference PLL in ENET_PLL register, but the code can
be re-used to enable the 125MHz PCIe reference in ENET_PLL, so pull
this code into separate function. Moreover, add the PCIe clock
enabling code.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Add SPL support to be able to detect a USB Mass Storage device
connected to a USB host. Once a USB Mass storage device is detected
the SPL will load the u-boot.img from a FAT partition to target address.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Patch adds modification to shared omap5 abb_setup() function, and
proper registers definitions needed for ABB setup sequence. ABB is
initialized for MPU voltage domain at OPP_NOM.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
ES1.1 silicon is a very minor variant of ES1.0. Add priliminary support
for ES1.1 IDCODE change.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
This patch enables dynamically powering down the
IO receiver when not performing a read on boards using DDR3.
This optimizes both active and standby power consumption.
This bit is not set on EVM SK and EVM 1.5 and later boards.
Setting the same.
This has been tested on PG2.0 EVM1.5, EVM1.2, EVM-SK, BBB.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Satyanarayana, Sandhya <sandhya.satyanarayana@ti.com>
Other TI processors like am33xx, omap4 and omap5 have called these variables
as NON_SECURE_SRAM_*, shouldn't be a big problem rename these variables to
be coherent.
One reason more to rename these variables is to have the possibility of any
OMAP3 board to use the ti_armv7_common.h include as the NON_SECURE_SRAM_END
is used to define the CONFIG_SYS_INIT_SP_ADDR variable.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
The commit
f3f98bb0 : "ARM: OMAP4/5: Do not configure non essential pads, clocks, dplls"
removed the config option aimed towards moving that stuff into kernel, which
renders some code unreachable. Remove that code.
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
The commit
f3f98bb0 : "ARM: OMAP4/5: Do not configure non essential pads, clocks, dplls"
removed the config option aimed towards moving that stuff into kernel, which
renders some code unreachable. Remove that code.
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Send RPC commands to the VideoCore to turn on the SDHCI and USB modules.
For SDHCI this isn't needed in practice, since the firmware already
turned on the power in order to load U-Boot. However, it's best to be
explicit. For USB, this is necessary, since the module isn't powered
otherwise. This will allow the kernel USB driver to work.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Commit 022298278 (mx6: soc: Disable VDDPU regulator) is causing kernel hang
for people using FSL kernel 3.0.35 and 3.10, so revert it for now.
Reported-by: Otavio Salvador <otavio@ossystems.com.br>
Reported-by: Pierre Aubert <p.aubert@staubli.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
This adds base register address of SH QSPI.
Currently, SH QSPI is used only from R8A7790 and R8A7791.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
SolidRun has designed the Hummingboard board based on mx6q/dl/solo.
Add the initial support for the mx6 solo variant.
More information about this hardware can be found at:
http://imx.solid-run.com/wiki/index.php?title=Carrier-One_Hardware
(Carrier-One was the previous name of Hummingboard).
Based on the work from Jon Nettleton <jon.nettleton@gmail.com>.
Signed-off-by: Jon Nettleton <jon.nettleton@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Provide an argument to enable_fec_anatop_clock() to specify the clock frequency
that will be generated.
No changes are made to mx6slevk, which uses the default 50MHz fec clock.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
The controller has 3 ports. The port0 is for USB 2.0 Phy, port1 and port2
are for HSIC phys. The usb 2.0 phy is already being setup. This patch
sets up the hsic phys.
Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org>
Bringing in the MMC tree means that CONFIG_BOUNCE_BUFFER needed to be
added to include/configs/exynos5-dt.h now.
Conflicts:
include/configs/exynos5250-dt.h
Signed-off-by: Tom Rini <trini@ti.com>
GPIO dummy routines are required for fdt build, may be removed
these dependencies once the u-boot fdt is fully optimized.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Added support to find the bootmodes by reading
slcr bootmode register. this can be helpful to
autoboot the configurations w.r.t a specified bootmode.
Added this functionality on board_late_init as it's not
needed for normal initializtion part.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
The toolchain sets __aarch64__ for both LE and BE. In the case of
posix_types.h we cannot reliably use config.h as that will lead to
problems. In the case of byteorder.h it's clearer to check the EB flag
being set in either case instead.
Cc: David Feng <fenghua@phytium.com.cn>
Signed-off-by: Tom Rini <trini@ti.com>
Amended by Albert ARIBAUD <albert.u.boot@aribaud.net> to
actually remove the config.h include from the posix_types.h
files, with permission from Tom Rini.
Relocation code based on a patch by Scott Wood, which is:
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: David Feng <fenghua@phytium.com.cn>
To add the DesignWare MMC driver support for Altera SOCFPGA. It
required information such as clocks and bus width from platform
specific files (SOCFPGA handoff files)
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
The macro allows easy setting in per-pin, as for example:
,----
| imx_iomux_v3_setup_pad(MX6_PAD_NANDF_D1__GPIO_2_1 | MUX_MODE_SION);
`----
The IOMUX_CONFIG_SION allows for reading PAD value from PSR register.
The following quote from the datasheet:
,----
| ...
| 28.4.2.2 GPIO Write Mode
| The programming sequence for driving output signals should be as follows:
| 1. Configure IOMUX to select GPIO mode (Via IOMUXC), also enable SION if need
| to read loopback pad value through PSR
| 2. Configure GPIO direction register to output (GPIO_GDIR[GDIR] set to 1b).
| 3. Write value to data register (GPIO_DR).
| ...
`----
This fixes the gpio_get_value to properly work when a GPIO is set for
output and has no conflicts.
Thanks for Benoît Thébaudeau <benoit.thebaudeau@advansee.com>, Fabio
Estevam <fabio.estevam@freescale.com> and Eric Bénard
<eric@eukrea.com> for helping to properly trace this down.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Stefano Babic <sbabic@denx.de>
As U-boot does not use GPU/VPU peripherals, shutdown the VDDPU regulator
in order to save power.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Jason Liu <r64343@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Adds code in pinmux and gpio framework to support Exynos5420.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch intends to add DDR3 initialization code for Exynos5420.
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch adds code for clock initialization and clock settings
of various IP's and controllers, required for Exynos5420
Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add dmc and phy_control register structure for 5420.
Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add structure for power register for Exynos5420
Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Adds base addresses of various IPs and controllers required for
Exynos5420.
Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Create a common board.c file for all functions which are common across
all EXYNOS5 platforms.
exynos_init function is provided for platform specific code.
Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
GP EVM has 1GB DDR3 attached(Part no: MT41K512M8RH).
Adding details for the same.
Below is the brief description of DDR3 init sequence(SW leveling):
-> Enable VTT regulator
-> Configure VTP
-> Configure DDR IO settings
-> Disable initialization and refreshes until EMIF registers are programmed.
-> Program Timing registers
-> Program leveling registers
-> Program PHY control and Temp alert and ZQ config registers.
-> Enable initialization and refreshes and configure SDRAM CONFIG register
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
AM4372 EPOS EVM has 1GB LPDDR2(Part no: MT42L256M32D2LG-25 WT:A)
Adding LPDDR2 init sequence and register details for the same.
Below is the brief description of LPDDR2 init sequence:
-> Configure VTP
-> Configure DDR IO settings
-> Disable initialization and refreshes until EMIF registers are programmed.
-> Program Timing registers
-> Program PHY control and Temp alert and ZQ config registers.
-> Enable initialization and refreshes and configure SDRAM CONFIG register
-> Wait till initialization is complete and the configure MR registers.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Updating the Multiplier and Dividers value for all DPLLs.
Safest OPP is read from DEV ATTRIBUTE register. Accoring to the value
returned the MPU DPLL is locked.
At different OPPs follwoing are the MPU locked frequencies.
OPP50 300MHz
OPP100 600MHz
OPP120 720MHz
OPPTB 800MHz
OPPNT 1000MHz
According to the latest DM following is the OPP table dependencies:
VDD_CORE VDD_MPU
OPP50 OPP50
OPP50 OPP100
OPP100 OPP50
OPP100 OPP100
OPP100 OPP120
So at different OPPs of MPU it is safest to lock CORE at OPP_NOM.
Following are the DPLL locking frequencies at OPP NOM:
Core locks at 1000MHz
Per locks at 960MHz
LPDDR2 locks at 266MHz
DDR3 locks at 400MHz
Touching AM33xx files also to get DPLL values specific to board but no
functionality difference.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Updating the mux data for UART, adding data for i2c0 and mmc.
And also updating pad_signals structure.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add support for reading onboard EEPROM to enable
board detection.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The CPU complex reset masks are not matching with the datasheet for
the CLK_RST_CONTROLLER_RST_CPU_CMPLX_SET/CLR_0 registers. For both T20
and T30 the register consist of groups of 4 bits, with one bit for
each CPU core. On T20 the 2 high bits of each group are always stubbed
as there is only 2 cores.
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swrren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add the Tegra30 SKU b1 and treat it like other Tegra30 chips.
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Reviewed-by: Julian Scheel <julian.scheel@avionic-design.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Move setup_sata function definition from platform file nitrogen6x.c
to arch/arm/imx-common/sata.c to avoid code duplication.
Signed-off-by: Giuseppe Pagano <giuseppe.pagano@seco.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
CC: Eric Nelson <eric.nelson@boundarydevices.com>
This allows the use of either or both declarations from
the files mx6q_pins.h and mx6dl_pins.h.
All board files should include <asm/arch/mx6-pins.h>
with one of the following defined in boards.cfg
MX6Q - for boards targeting i.MX6Q or i.MX6D
MX6DL - for boards targeting i.MX6DL
MX6S - for boards targeting i.MX6S
MX6QDL - for boards that support any of the above with
run-time detection
Pad declarations will be MX6_PAD_x for single-variant boards
and MX6Q_PAD_x and MX6DL_PAD_x for boards supporting both
processor classes.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Stefano Babic <sbabic@denx.de>
With the current scenario SPL size is being overlapped with the public
stack and not allowing any OMAP4 device to boot. So the suggestion came
up was to move the TEXT_BASE down to non-HS limit. Fixing the same and
also moving the SRAM_SCRATCH_SPACE_ADDR up to the end of image
downloadable area.
Discussion on this can be seen here:
https://www.mail-archive.com/u-boot@lists.denx.de/msg127147.html
Tested on OMAP4460 PANDA.
Reported-by: Chao Xu <caesarxuchao@gmail.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
In order to get the very same value for legacy pin definitions and new gpio
definitions set the legacy PIN_BASE to 0.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
This patch define new names for GPIO pins on at91 devices. Follow up patches
will convert the whole infrastructure to use these new definitions.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Tested-by: Bo Shen <voice.shen@atmel.com>
This patch change the per_clocks_enable() function used in OMAP3
code to enable peripherals clocks. Only required clock should be
activated. So if the board use the uart(x) as a console we need
to activate it. The Board's config should include define to enable
every subsystem that the board use. For a complete list
of affected peripherals, registers CM_FCLKEN_PER and CM_ICLKEN_PER
should be checked.
Right now the bootloader can enable and disable clocks for:
uart(x) using CONFIG_SYS_NS16550
gpio bank (x) using CONFIG_OMAP3_GPIO_X with X = { 2, 3, 4, 5, 6 }
i2c bus using CONFIG_DRIVER_OMAP34XX_I2C.
Not required gptimer(x) and mcbsp(x) for booting are disabled by default and
are not supported by any define.
Their activation need to included in the per_clocks_enable if the
peripheral is included. Not booting board should enable the peripheral
clock connected to their driver
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tom Rini <trini@ti.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
When core power domain hits oswr, then DDR3 memories does not come back
while resuming. This is because when EMIF registers are lost, then the
controller takes care of copying the values from the shadow registers.
If the shadow registers are not updated with the right values, then this
results in incorrect settings while resuming. So updating the shadow registers
with the corresponding status registers here during the boot.
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Currently the DDR3 memory on DRA7 ES1.0 evm board is enabled using
software leveling. This was done since hardware leveling was not
working. Now that the right sequence to do hw leveling is identified,
use it. This is required for EMIF clockdomain to idle and come back
during lowpower usecases.
Signed-off-by: Sricharan R <r.sricharan@ti.com>
A generic is_dra7xx cpu check is useful for grouping
all the revisions under that. This is used in the
subsequent patches.
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Based on the definitive guide to EMIF configuration[1] certain registers
that we have been modifying (and are documented registers) should be
left in their reset values rather than modified. This has been tested
on AM335x GP EVM and Beaglebone White.
[1]: http://processors.wiki.ti.com/index.php/AM335x_EMIF_Configuration_tips
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Cc: Javier Martinez Canillas <javier@dowhile0.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Tom Rini <trini@ti.com>
Tested-by: Matt Porter <matt.porter@linaro.org>
Adding Freeze Controller driver. All HPS IOs need to be
in freeze state during pin mux or IO buffer configuration.
It is to avoid any glitch which might happen
during the configuration from propagating to external devices.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Wolfgang Denk <wd@denx.de>
CC: Pavel Machek <pavel@denx.de>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Tom Rini <trini@ti.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
This patch implements a custom spi_copy funtion to copy u-boot from SF
to RAM. This is faster then iROM spi_copy funtion as this runs spi at
50Mhz and also in WORD mode of operation.
Changed a printf in pinmux.c to debug just to avoid the compilation
error in SPL.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Tom Wai-Hong Tam <waihong@chromium.org>
Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The koelsch board has R8A7791, 2GB DDR3-SDRAM, USB,
Quad SPI, Ethernet, and more.
This patch supports the following functions:
- DDR3-SDRAM
- SCIF
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
CC: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CC: Albert Aribaud <albert.u.boot@aribaud.net>
Renesas R8A7791 is CPU with Cortex-A15.
This supports the basic register definition and GPIO and
framework of PFC.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
CC: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CC: Albert Aribaud <albert.u.boot@aribaud.net>
Renesas R8A7790 is CPU with Cortex-A7 and A15.
This supports the basic register definition and GPIO and
framework of PFC.
Signed-off-by: Kouei Abe <kouei.abe.cp@renesas.com>
Signed-off-by: Ryo Kataoka <ryo.kataoka.wt@renesas.com>
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
CC: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CC: Albert Aribaud <albert.u.boot@aribaud.net>
Enable Atmel sama5d3xek boart spl boot support, which can load u-boot
from SD card with FAT file system.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
The MPDDRC supports different type of SDRAM
This patch add ddr2 initialization function
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
The offset of MULA field in PLLA register in sama5d3 is 18,
and the length only 7 bits.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
GPMC controller is common IP to interface with both NAND and NOR flash devices.
Also, it supports max 8 chip-selects, which can be independently connected to
any of the devices.
But ROM code expects the boot-device to be connected to only chip-select[0].
Thus to resolve conflict between NOR and NAND boot. This patch:
- combines NOR and NAND configs spread in board files to common gpmc_init()
- configures GPMC based on boot-mode selected for SPL boot.
Signed-off-by: Pekon Gupta <pekon@ti.com>
BCH8_ECC scheme implemented in omap_gpmc.c driver has following favours
+-----------------------------------+-----------------+-----------------+
|ECC Scheme | ECC Calculation | Error Detection |
+-----------------------------------+-----------------+-----------------+
|OMAP_ECC_BCH8_CODE_HW |GPMC |ELM H/W engine |
|OMAP_ECC_BCH8_CODE_HW_DETECTION_SW |GPMC |S/W BCH library |
+-----------------------------------+-----------------+-----------------+
Current implementation limits the BCH8_CODE_HW only for AM33xx device family.
(using CONFIG_AM33XX). However, other SoC families (like TI81xx) also have
ELM hardware module, and can support ECC error detection using ELM.
This patch
- removes CONFIG_AM33xx
Thus this driver can be reused by all devices having ELM h/w engine.
- adds omap_select_ecc_scheme()
A common function to handle ecc-scheme related configurations. This
can be used both during device-probe and via user-space u-boot commads
to change ecc-scheme. During device probe ecc-scheme is selected based
on CONFIG_NAND_OMAP_ELM or CONFIG_NAND_OMAP_BCH8
- enables CONFIG_BCH
S/W library (lib/bch.c) required by OMAP_ECC_BCHx_CODE_HW_DETECTION_SW
is enabled by CONFIG_BCH.
- enables CONFIG_SYS_NAND_ONFI_DETECTION
for auto-detection of ONFI compliant NAND devices
- updates following README doc
doc/README.nand
board/ti/am335x/README
doc/README.omap3
Signed-off-by: Pekon Gupta <pekon@ti.com>
[scottwood@freescale.com: fixed unused variable warning]
Signed-off-by: Scott Wood <scottwood@freescale.com>
ELM hardware engine which is used for ECC error detection, is present on all
latest OMAP SoC (like OMAP4xxx, OMAP5xxx, DRA7xxx, AM33xx, AM43xx). Thus ELM
driver should be moved to common drivers/mtd/nand/ folder so that all SoC
having on-chip ELM hardware engine can re-use it.
This patch has following changes:
- mv arch/arm/include/asm/arch-am33xx/elm.h arch/arm/include/asm/omap_elm.h
- mv arch/arm/cpu/armv7/am33xx/elm.c drivers/mtd/nand/omap_elm.c
- update Makefiles
- update #include <asm/elm.h>
- add CONFIG_NAND_OMAP_ELM to compile driver/mtd/nand/omap_elm.c
and include in all board configs using AM33xx SoC platform.
Signed-off-by: Pekon Gupta <pekon@ti.com>
The SAMA5D36 chip is the superset product of SAMA5D3x family.
For detail information please refer to:
http://www.atmel.com/Microsite/sama5d3/default.aspx
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
- add omap24xx driver to new multibus/multiadpater support
- adapted all config files, which uses this driver
Tested on the am335x based siemens boards rut, dxr2 and pxm2
posted here:
http://patchwork.ozlabs.org/patch/263211/
Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Tom Rini <trini@ti.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Steve Sakoman <sakoman@gmail.com>
Cc: Thomas Weber <weber@corscience.de>
Cc: Tom Rix <Tom.Rix@windriver.com>
Cc: Grazvydas Ignotas <notasas@gmail.com>
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Cc: Luca Ceresoli <luca.ceresoli@comelit.it>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Ilya Yanok <yanok@emcraft.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Nishanth Menon <nm@ti.com>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: Peter Barada <peter.barada@logicpd.com>
Cc: Nagendra T S <nagendra@mistralsolutions.com>
Cc: Michael Jones <michael.jones@matrix-vision.de>
Cc: Raphael Assenat <raph@8d.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Stefano Babic <sbabic@denx.de>
Add the missing "right" field to struct bcm2835_mbox_tag_overscan.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Conflicts:
arch/arm/cpu/arm926ejs/mxs/Makefile
board/compulab/cm_t35/Makefile
board/corscience/tricorder/Makefile
board/ppcag/bg0900/Makefile
drivers/bootcount/Makefile
include/configs/omap4_common.h
include/configs/pdnb3.h
Makefile conflicts are due to additions/removals of
object files on the ARM branch vs KBuild introduction
on the main branch. Resolution consists in adjusting
the list of object files in the main branch version.
This also applies to two files which are not listed
as conflicting but had to be modified:
board/compulab/common/Makefile
board/udoo/Makefile
include/configs/omap4_common.h conflicts are due to
the OMAP4 conversion to ti_armv7_common.h on the ARM
side, and CONFIG_SYS_HZ removal on the main side.
Resolution is to convert as this icludes removal of
CONFIG_SYS_HZ.
include/configs/pdnb3.h is due to a removal on ARM side.
Trivial resolution is to remove the file.
Note: 'git show' will also list two files just because
they are new:
include/configs/am335x_igep0033.h
include/configs/omap3_igep00x0.h
Linux Kernel abolished include/linux/config.h long time ago.
(around version v2.6.18..v2.6.19)
We don't need to provide Linux copatibility any more.
This commit deletes include/linux/config.h
and fixes source files not to include this.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Roger Meier <r.meier@siemens.com>
Acked-by: Bo Shen <voice.shen@atmel.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Add usb host support for at91sam9n12ek board.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
The change from 0x64656465 to 0x64646464 is to remove the weak pull
enabled on DQS, nDQS lines. This pulls the differential signals in the
same direction which is not intended. So disabling the weak pulls improves
signal integrity.
On the uEVM there are 4 DDR3 devices. The VREF for 2 of the devices is powered by
the OMAP's VREF_CA_OUT pins. The VREF on the other 2 devices is powered by the OMAP's
VREF_DQ_OUT pins. So the net effect here is that only half of the DDR3 devices were being
supplied a VREF! This was clearly a mistake. The second change improves the robustness of
the interface and was specifically seen to cure corruption observed at high temperatures
on some boards.
With the above two changes better memory stability was observed with extended
temperature ranges around 100C.
Signed-off-by: Sricharan R <r.sricharan@ti.com>
UART booting is supported on this SoC, but via UART3 rather than UART1.
Because of this we must change the board to use UART3 for all console
access (only one UART is exposed on this board and a slight HW mod is
required to switch UARTs).
Signed-off-by: Minal Shah <minal.shah@ti.com>
[trini: Make apply to mainline, reword commit]
Signed-off-by: Tom Rini <trini@ti.com>
This removes the PAD_CTL_DSE_120ohm as done for i.MX6Q's IPU1_DI0_PIN4
pin definition and makes it aligned with 3.0.35-4.1.0 and 3.12
mainline kernel.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
SMDK5420 has a new Security Management Unit added
for dwmmc driver, hence, configuring the control
registers to support booting via eMMC.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Add the support for the am437x xhci usb host.
The xHCI host on AM437 is connected to a usb2 phy so need to
add support to enable those clocks.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Add the support for the dra7xx xhci usb host.
dra7xx does not contain an EHCI controller so the headers
can be removed from the board file.
The xHCI host on dra7xx is connected to a usb2 phy so need to
add support to enable those clocks.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
This commit unifies board-specific USB initialization implementations
under one symbol (usb_board_init), declaration of which is available in
usb.h.
New API allows selective initialization of USB controllers whenever needed.
Signed-off-by: Mateusz Zalega <m.zalega@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Add the OMAP file for the xHCI Host controller
This code will initilialize the proper components within the
OMAP5 to enable the xHCI host controller.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Adding methods to turn on/off power to USB3.0 type PHY
as and when required by the controller.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Julius Werner <jwerner@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Marek Vasut <marex@denx.de>
This adds driver layer for xHCI controller in Samsung's
exynos5 soc. This interacts with xHCI host controller stack.
Signed-off-by: Vikas C Sajjan <vikas.sajjan@samsung.com>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Julius Werner <jwerner@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Marek Vasut <marex@denx.de>
In case the MX23/MX28 is switched into JTAG mode via the BootMode select
switches, the BootROM bypasses the CPU core registers initialization.
This in turn means that the Stack Pointer (SP) register is not set as
it is in every other mode of operation, but instead is only zeroed out.
To prevent U-Boot SPL from crashing in this obscure JTAG mode, configure
the SP to point at the CONFIG_SYS_INIT_SP_ADDR if the SP is zeroed out.
Note that in case the SP is already configured, we must preserve that exact
SP value and must not modify it. This is important since in every other mode
but the JTAG mode, the SPL returns into the BootROM and BootROM in turn loads
U-Boot itself. If the SP were to be corrupted, the BootROM won't be able to
continue it's operation after returned from SPL and the system would crash.
Finally, add the JTAG mode switch identifier, so it's not recognised as
Unknown mode.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Add a MAC address create based on the OMAP die ID registers.
Then poplulate the ethaddr enviroment variable so that the device
tree alias can be updated prior to boot.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Since SPI register access is so expensive, it is worth transferring data
a word at a time if we can. This complicates the driver unfortunately.
Use the byte-swapping feature to avoid having to convert to/from big
endian in software.
This change increases speed from about 2MB/s to about 4.5MB/s.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Adding System Manager driver which will configure the
pin mux for real hardware Cyclone V development kit
(not Virtual Platform)
Signed-off-by: Chin Liang See <clsee@altera.com>
Reviewed-by: Pavel Machek <pavel@denx.de>
Acked-by: Dinh Nguyen <dinguyen@altera.com>
Cc: Wolfgang Denk <wd@denx.de>
CC: Pavel Machek <pavel@denx.de>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Tom Rini <trini@ti.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
We can run the DDR at 400MHz, so update the timings for that purpose.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
For the KVM and XEN hypervisors to be usable, we need to enter the
kernel in HYP mode. Now that we already are in non-secure state,
HYP mode switching is within short reach.
While doing the non-secure switch, we have to enable the HVC
instruction and setup the HYP mode HVBAR (while still secure).
The actual switch is done by dropping back from a HYP mode handler
without actually leaving HYP mode, so we introduce a new handler
routine in our new secure exception vector table.
In the assembly switching routine we save and restore the banked LR
and SP registers around the hypercall to do the actual HYP mode
switch.
The C routine first checks whether we are in HYP mode already and
also whether the virtualization extensions are available. It also
checks whether the HYP mode switch was finally successful.
The bootm command part only calls the new function after the
non-secure switch.
Signed-off-by: Andre Przywara <andre.przywara@linaro.org>
Currently the non-secure switch is only done for the boot processor.
To enable full SMP support, we have to switch all secondary cores
into non-secure state also.
So we add an entry point for secondary CPUs coming out of low-power
state and make sure we put them into WFI again after having switched
to non-secure state.
For this we acknowledge and EOI the wake-up IPI, then go into WFI.
Once being kicked out of it later, we sanity check that the start
address has actually been changed (since another attempt to switch
to non-secure would block the core) and jump to the new address.
The actual CPU kick is done by sending an inter-processor interrupt
via the GIC to all CPU interfaces except the requesting processor.
The secondary cores will then setup their respective GIC CPU
interface.
While this approach is pretty universal across several ARMv7 boards,
we make this function weak in case someone needs to tweak this for
a specific board.
The way of setting the secondary's start address is board specific,
but mostly different only in the actual SMP pen address, so we also
provide a weak default implementation and just depend on the proper
address to be set in the config file.
Signed-off-by: Andre Przywara <andre.przywara@linaro.org>
The core specific part of the work is done in the assembly routine
in nonsec_virt.S, introduced with the previous patch, but for the full
glory we need to setup the GIC distributor interface once for the
whole system, which is done in C here.
The routine is placed in arch/arm/cpu/armv7 to allow easy access from
other ARMv7 boards.
We check the availability of the security extensions first.
Since we need a safe way to access the GIC, we use the PERIPHBASE
registers on Cortex-A15 and A7 CPUs and do some sanity checks.
Boards not implementing the CBAR can override this value via a
configuration file variable.
Then we actually do the GIC enablement:
a) enable the GIC distributor, both for non-secure and secure state
(GICD_CTLR[1:0] = 11b)
b) allow all interrupts to be handled from non-secure state
(GICD_IGROUPRn = 0xFFFFFFFF)
The core specific GIC setup is then done in the assembly routine.
Signed-off-by: Andre Przywara <andre.przywara@linaro.org>
While actually switching to non-secure state is one thing, another
part of this process is to make sure that we still have full access
to the interrupt controller (GIC).
The GIC is fully aware of secure vs. non-secure state, some
registers are banked, others may be configured to be accessible from
secure state only.
To be as generic as possible, we get the GIC memory mapped address
based on the PERIPHBASE value in the CBAR register. Since this
register is not architecturally defined, we check the MIDR before to
be from an A15 or A7.
For CPUs not having the CBAR or boards with wrong information herein
we allow providing the base address as a configuration variable.
Now that we know the GIC address, we:
a) allow private interrupts to be delivered to the core
(GICD_IGROUPR0 = 0xFFFFFFFF)
b) enable the CPU interface (GICC_CTLR[0] = 1)
c) set the priority filter to allow non-secure interrupts
(GICC_PMR = 0xFF)
Also we allow access to all coprocessor interfaces from non-secure
state by writing the appropriate bits in the NSACR register.
The generic timer base frequency register is only accessible from
secure state, so we have to program it now. Actually this should be
done from primary firmware before, but some boards seems to omit
this, so if needed we do this here with a board specific value.
The Versatile Express board does not need this, so we remove the
frequency from the configuration file here.
After having switched to non-secure state, we also enable the
non-secure GIC CPU interface, since this register is banked.
Since we need to call this routine also directly from the smp_pen
later (where we don't have any stack), we can only use caller saved
registers r0-r3 and r12 to not mess with the compiler.
Signed-off-by: Andre Przywara <andre.przywara@linaro.org>
armv7.h contains some useful constants, but also C prototypes.
To include it also in assembly files, protect the non-assembly
part appropriately.
Signed-off-by: Andre Przywara <andre.przywara@linaro.org>
