Add support for A83T dram. Register are different from sun8i A33.
init code is similar to A33 dram init.
hope we'll shift duplicate code in dram_sun8i_*
to dram helper in future.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add basic clocks pll1, pll5, and some default values from allwinner u-boot.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
[hdegoede@redhat.com] Fix PLL6 init to run at 600 MHz instead of 288 MHz,
fixing the mmc support not working
[hdegoede@redhat.com] Fix PLL init code to properly wait for the PLL-s to
stabilize, fixing cold-booting directly from sdcard not working
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
On A83T, PB9,PB10 are UART0 pins.
On allwinner A83T Dev board(h8homlet), this uart0 serial connector
is exposed.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
According to the datasheets the max speed of AHB1 is 276 MHz, so
setting it to PLL6 / 3 which gives us 200MHz everywhere is fine,
and gives us a nice speed-up in certain workloads.
Suggested-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Tested-by: Chen-Yu Tsai <wens@csie.org>
Should use parenthese to wrap the macro definition, otherwise
we will encounter error like the following:
"
if (base_addr != LCDIF1_BASE_ADDR) {
puts("Wrong LCD interface!\n");
return -EINVAL;
}
"
Without this patch, we will always encounter "Wrong LCD interface".
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
GRF is the gereral register file. Add header files with register definitions.
Signed-off-by: Lin Huang <hl@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add a driver for setting up and modifying the various PLLs, peripheral
clocks and mmc clocks on RK3036
Signed-off-by: Lin Huang <hl@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
some rockchip soc will not include lib/timer.c in SPL stage,
so implement timer driver for some soc can use us delay function in SPL.
Signed-off-by: Lin Huang <hl@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
The early MMU table doesn't enable all addresses. Unused addresses
are marked as invalid, as introduced by commit 9979922. An entry
was missing for NAND flash space, causing nand boot failure.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Alison Wang <alison.wang@freescale.com>
CC: Prabhakar Kushwaha <prabhakar@freescale.com>
If the core runs at higher than x3 speed of the platform, there is
possiblity about sev instruction to getting missed by other cores.
This is because of SoC Run Control block may not able to sample
the EVENTI(Sev) signals.
Configure Run Control and EPU to periodically send out EVENTI signals to
wake up A57 cores.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
For most device addresses excution shouldn't be allowed. Revise
the MMU table to enforce execute-never bits. OCRAM, DDR and IFC
are allowed for excution.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reported-by: Zhichun Hua <zhichun.hua@freescale.com>
Freescale LSCH3 platforms use two DDR controlers interleaving mode out of
reset. It can be configured to disable one controller. To support this
operation, the driver needs to detect and skip the disabled controller.
Signed-off-by: York Sun <yorksun@freescale.com>
Add support for the third USB controller for LS1043A.
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
LS1043AQDS Specification:
-------------------------
Memory subsystem:
* 2GByte DDR4 DIMM
* 128 Mbyte NOR flash single-chip memory
* 512 Mbyte NAND flash
* 16 Mbyte high-speed SPI flash
* SD connector to interface with the SD memory card
Ethernet:
* Two RGMII ports
* XFI 10G port
* SGMII
* QSGMII with 4x 1G ports
PCIe: supports Gen 1 and Gen 2
SATA 3.0: one SATA 3.0 port
USB 3.0: two micro AB connector and one type A connector
UART: supports two UARTs up to 115200 bps for console
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
[York Sun: Add CONFIG_SYS_NS16550=y in defconfig]
Reviewed-by: York Sun <yorksun@freescale.com>
The endian and base address of PEX LUT register region is different
between Chassis 2 and Chassis 3, so move the base address definition
to chassis specific header file and add pex_lut_* functions to access
LUT register.
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Freescale's LS2085A is a another personality of LS2080A SoC with
support of AIOP and DP-DDR.
This Patch adds support of LS2085A Personality.
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: Updated MAINTAINERS files
Dropped #ifdef in cpu.h
Add CONFIG_SYS_NS16550=y in defconfig]
Reviewed-by: York Sun <yorksun@freescale.com>
LS2080A is a prime personality of Freescale’s LS2085A. It is a non-AIOP
personality without support of DP-DDR, L2 switch, 1588, PCIe endpoint etc.
So renaming existing LS2085A code base to reflect LS2080A (Prime personality)
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: Dropped #ifdef in cpu.c for cpu_type_list]
Reviewed-by: York Sun <yorksun@freescale.com>
This patch addresses a problem mentioned recently on this mailing list:
[1].
In that posting a LS1021 based system was locking up at about 5 minutes
after boot, but the problem was mysteriously related to the toolchain
used for building u-boot. Debugging the problem reveals a stuck
interrupt 29 on the GIC.
It appears Freescale's LS1021 support in u-boot erroneously sets the
64-bit ARM generic PL1 physical time CompareValue register to all-ones
with a 32-bit value. This causes the timer compare to fire 344 seconds
after u-boot configures it. Depending on how fast u-boot gets the
kernel booted, this amounts to about 5-minutes of Linux uptime before
locking up.
Apparently the bug is masked by some toolchains. Perhaps this is
explained by default compiler options, word sizes, or binutils versions.
At any rate this patch makes the manipulation explicitly 64-bit which
alleviates the issue.
[1]
https://lists.yoctoproject.org/pipermail/meta-freescale/2015-June/014400.html
Signed-off-by: Chris Kilgour <techie@whiterocker.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
We should also take MX6D option in consideration when defining
imx_iomux_v3_setup_pad().
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
The 3.4 kernel from the Allwinner SDK is clocking AHB1 at 200MHz
on Allwinner H3 and using PLL6 as the clock source (PLL6/3).
This can be verified by reading the value of the AHB1_APB1_CFG_REG
register via /dev/mem. It always reads as 0x3180 regardless of
the current cpufreq operating point. So this configuration should
be safe for use in U-Boot too.
PLL6 also needs to be configured before it is used as the clock
source, according to the "CCU / Programming Guidelines" section
of the Allwinner manual.
The current low AHB1 clock speed is limiting the USB transfer
speed when booting via FEL. This patch can increase the FEL USB
transfer speed from ~510 KB/s to ~950 KB/s.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Based on existing A23/A33 code and the original H3 boot0.
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add initial sun8i H3 support, only uart + mmc are supported for now.
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Make spl_*_load_image() functions return a value instead of
hanging if a problem is encountered. This enables main spl code
to make the decision whether to hang or not, thus preparing
it to support alternative boot devices.
Some boot devices (namely nand and spi) do not hang on error.
Instead, they return normally and SPL proceeds to boot the
contents of the load address. This is considered a bug and
is rectified by hanging on error for these devices as well.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Hans De Goede <hdegoede@redhat.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Jagan Teki <jteki@openedev.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Enable TI_EDMA3 and QUAD read support for ti_qspi on am43xx, this
increases read performance to 4 MB/s.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Fix below compilation warnings-
drivers/gpio/hi6220_gpio.c: In function ‘hi6220_gpio_probe’:
drivers/gpio/hi6220_gpio.c:82:15: warning: cast to pointer from integer
of different size [-Wint-to-pointer-cast]
bank->base = (u8 *)plat->base;
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Introudce a new function lcdif_power_down.
1. Waits for a VSYNC interrupt to guarantee the reset is done at the
VSYNC edge, which somehow makes the LCDIF consume the display FIFO(?)
and helps the LCDIF work normally at the kernel stage.
2. Add power down function to stop lcdif.
The reason to introduce lcdif_power_down is that we want lcdif to be in
initial state when doing uboot reset or before kernel boot to make
system stable, otherwise system may hang.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
Implement mxs_set_lcdclk, enable_lcdif_clock and enable_pll_video.
The three API can be used to configure lcdif related clock when
CONFIG_VIDEO_MXS enabled.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
1. Move WDOG3_BASE_ADDR to '#if !(defined(__ASSEMBLY__))'.
2. Add i.MX6UL LCDIF register base address. And Introduce
LCDIF1_BASE_ADDR to support runtime check.
3. include <asm/imx-common/regs-lcdif.h> for imx-regs.h to avoid
building error for mxsfb.c, since mxsfb.c use imx-regs.h.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Share one lcdif structure for i.MXes.
1. Discard struct mxs_lcdif_regs from imx-regs.h of i.MX7
2. Add i.MX6SX/6UL/7D support in imx-lcdif.h of imx-common
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Move 'struct mxs_lcdif_regs' and lcdif related macro definitions to
arch/arm/include/asm/imx-common/regs-lcdif.h.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
There are uint8_t, uint32_t types in regs-common.h, so include
linux/types.h.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Change mxs_set_lcdclk prototype to add a new parameter
base_addr. There are two LCD interfaces for i.MX6SX,
we may support LCDIF1 or LCDIF2.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
1. add basic psci support for imx7 chip.
2. support cpu_on and cpu_off.
3. switch to non-secure mode when boot linux kernel.
4. set csu allow accessing all peripherial register in non-secure mode.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Rename GPU functions to less generic names to avoid potential name
collisions.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
There is no justification for this function, especially in exported
form.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The implementation of noncached_init() uses define MMU_SECTION_SIZE.
Define this on ARM64.
Move the prototype of noncached_{init,alloc}() to a location that
doesn't depend on !defined(CONFIG_ARM64).
Note that noncached_init() calls mmu_set_region_dcache_behaviour() which
relies on something having set up translation tables with 2MB block size.
The core ARMv8 MMU setup code does not do this by default, but currently
relies on SoC specific MMU setup code. Be aware of this before enabling
this feature on your platform!
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Old sector number is not being cleared from FLASH_CR register. For example
when first erased sector was 001 and then you want to erase sector 010,
sector 011 gets erased instead.
This patch clears old sector number from FLASH_CR register before a new
one is written.
Signed-off-by: Vadzim Dambrouski <pftbest@gmail.com>
When building a Thumb-1-only target with CONFIG_SYS_THUMB_BUILD,
some files fail to build, most of the time because they include
mcr instructions, which only exist for Thumb-2.
This patch introduces a Kconfig option CONFIG_THUMB2 and uses
it to select between Thumb-2 and ARM mode for the aforementioned
files.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
This patch fix compilation error:
drivers/mmc/zynq_sdhci.c:16:5: error: conflicting types for
‘zynq_sdhci_init’
int zynq_sdhci_init(phys_addr_t regbase)
^
In file included from drivers/mmc/zynq_sdhci.c:14:0:
./arch/arm/include/asm/arch/sys_proto.h:16:5: note: previous declaration
of ‘zynq_sdhci_init’ was here
int zynq_sdhci_init(unsigned long regbase);
^
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The generic bitops headers are required when calling logarithmic
functions, such as ilog2().
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Add secure boot fuse helper struct to abstract the way
to find out secure boot settings per SoC iMX family
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Add CONFIG_ROM_UNIFIED_SECTIONS for mx6sx and mx6ul target
platforms to resolve corresponding HAB_RVT_BASE base address,
the RVT table contains pointers to the HAB API functions in
ROM code.
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Rework secure boot support for imx6, move existing hab support
for imx6 into imx-common for SoC reuse.
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Move common chip revision id's to main cpu header file
mx25 generic include cpu header for chip revision
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Freescale ARM-based Layerscape LS102xA contain a SATA controller
which comply with the serial ATA 3.0 specification and the
AHCI 1.3 specification.
This patch adds SATA feature on ls1021aqds and ls1021atwr boards.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Freescale LayerScape with Chassis Generation 2 is a set of SoCs with
ARMv8 cores and 2rd generation of Chassis.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
There are two LS series processors are built on ARMv8 Layersacpe
architecture currently, LS2085A and LS1043A. They are based on
ARMv8 core although use different chassis, so create fsl-layerscape
to refactor the common code for the LS series processors which also
paves the way for adding LS1043A platform.
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Config Security Level Register is different between different SoCs,
so put the CSL register definition into the arch specific directory.
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Enable snooping for CAAM read & write transactions by
programming the SCFG snoop configuration register:
SCFG_SNPCNFGCR[SECRDSNP]
SCFG_SNPCNFGCR[SECWRSNP]
Signed-off-by: Horia Geantă <horia.geanta@freescale.com>
Reviewed-by: Zhengxiong Jin <Jason.Jin@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Data types and I/O functions have been defined for
64 bit physical addresses in arm.
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
We have finished Generic Board conversion for ARM and PowerPC, i.e.
all the boards have been converted except OpenRISC, SuperH, SPARC,
which have not supported Generic Board framework yet.
Select SYS_GENERIC_BOARD in arch/Kconfig and delete all the macro
defines in include/configs/*.h.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Existing driver gets the actual omap hammc base address + 0x100
bytes as the first 0x100 bytes is not used by the driver. But
with DM conversion the base address from DT is different, to
accommodate the offset adding res0[0x100] to struct hsmmc.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
In K2G, Ethernet doesn't support SGMII instead it support RGMII,
adding support to the driver to connect to RGMII phy.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Phy mode is a board property and it can be different between
multiple board and ports, so it should not be hardcoded in
driver to one specific mode. So adding a field in eth_priv_t
structure to pass phy mode to driver.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add clock information for Galileo
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Since there is a common function to grab the serial number from the die id bits,
it makes sense have one to parse that serial number and feed it to the serial
ATAG.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
This introduces omap_die_id_display to display the full die id.
There is no need to store it in an environment variable, that no boot script
is using anyway.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
Now that we have a common prototype to grab the omap die id, functions to figure
out a serial number and usb ethernet address can use it directly.
Those also get an omap_die_id prefix for better consistency.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
This introduces omap4 support for omap_die_id, which matches the common
omap_die_id definition. It replaces board-specific code to grab the die id bits.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
This replaces the previous get_dieid definition with omap_die_id, that matches
the common omap_die_id definition.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
This introduces a common definition for omap_die_id, that aims at providing a
common interface for accessing omap platform's die id bits.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
Update the L2 AUX CTRL settings for the SoCFPGA.
Enabling D and I prefetch bits helps improve SDRAM performance on the
platform.
Also, we need to enable bit 22 of the L2. By not having bit 22 set in the
PL310 Auxiliary Control register (shared attribute override enable) has the
side effect of transforming Normal Shared Non-cacheable reads into Cacheable
no-allocate reads.
Coherent DMA buffers in Linux always have a Cacheable alias via the
kernel linear mapping and the processor can speculatively load cache
lines into the PL310 controller. With bit 22 cleared, Non-cacheable
reads would unexpectedly hit such cache lines leading to buffer
corruption.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Add 'volatile' qualifier to the asm statement in get_cr()
so that the statement is not optimized out by the compiler.
(http://comments.gmane.org/gmane.linux.linaro.toolchain/5163)
Without the 'volatile', get_cr() returns a wrong value which
prevents enabling the MMU and later causes a PCIE VA access
failure.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
PCI driver currently hangs on mx6qp.
Toggle the reset bit with the appropriate timings to fix the issue.
Based on the FSL kernel driver implementation.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
For EL3 and EL2, the documentation says that bits 31 and 23 are reserved
but should be written as 1.
For EL1, only bit 23 is not reserved, so only write bit 31 as 1.
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use the inner shareable attribute for memory, which makes more sense
considering that this code is called when caches are being enabled.
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
According to ARM PrimeCell PL175 documentation WAIT_OEN config value
is defined without any additional clocks added to the value set by a
client, the change fixes the wrong interface to WAIT_OEN config.
The change also touches a single user of LPC32xx EMC and corrects
configured "output enable delay" value on its side according to the
changed interface.
No functional change intended.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
The VF610 DDRMC driver code contains settings which are
board-specific. Move these out to boards so that new boards
can define their own without having to modify the driver.
Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
This patch extends the misc_init_r() function on sunxi boards
to test for the presence of a suitable "sunxi" SPL header. If
found, and the loader ("fel" utility) provided a non-zero value
for the boot.scr address, then the corresponding environment
variable fel_scriptaddr gets set.
misc_init_r() also sets (or clears) the "fel_booted" variable depending
on the active boot device, using the same logic as spl_boot_device().
The goal is to provide sufficient information (within the U-Boot
environment) to make intelligent decisions on how to continue the boot
process, allowing specific customizations for the "FEL boot" case.
Signed-off-by: Bernhard Nortmann <bernhard.nortmann@web.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This patch follows up on a discussion of ways to improve support
for the sunxi FEL ("USB boot") mechanism, especially with regard
to boot scripts, see:
https://groups.google.com/d/msg/linux-sunxi/wBEGUoLNRro/rHGq6nSYCQAJ
The idea is to convert the (currently unused) "pad" bytes in the
SPL header into an area where data can be passed to U-Boot. To
do this safely, we have to make sure that we're actually using
our "sunxi" flavor of the SPL, and not the Allwinner boot0.
The modified mksunxiboot introduces a special signature to the
SPL header in place of the "pub_head_size" field. This can be
used to reliably distinguish between compatible versions of sunxi
SPL and anything else (older variants or Allwinner's boot0).
Signed-off-by: Bernhard Nortmann <bernhard.nortmann@web.de>
Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The sunxi platform currently doesn't seem to make any use of the
asm/arch-sunxi/spl.h file. This patch moves some declarations from
tools/mksunxiboot.c into it.
This enables us to reuse those definitions when extending the
sunxi board code (boards/sunxi/boards.c).
Signed-off-by: Bernhard Nortmann <bernhard.nortmann@web.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Enabling a PLL while IDDQ is high. The Linux kernel checks for this
condition and warns about it verbosely, so while this seems to work
fine, fix it up according to the programming guidelines provided in
the Tegra K1 TRM (v02p), Section 5.3.8.1 ("PLLC and PLLC4 Startup
Sequence"). The Tegra114 TRM doesn't contain this information, but
the programming of PLLC is the same on Tegra114 and Tegra124.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Enabling a PLL while IDDQ is high. The Linux kernel checks for this
condition and warns about it verbosely, so while this seems to work
fine, fix it up according to the programming guidelines provided in
the Tegra K1 TRM (v02p), Section 5.3.8.1 ("PLLC and PLLC4 Startup
Sequence").
Reported-by: Nicolas Chauvet <kwizart@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
On currently supported SoCs, clk_m always runs at the same frequency as
the oscillator input. However newer SoC generations such as Tegra210 no
longer have that restriction. Prepare for that by separating clk_m from
the oscillator clock and allow SoC code to override the clk_m rate.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This function is deleted by commit 2fccd2d96b
"tegra: Convert tegra GPIO driver to use driver model".
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This arch does not seem to be supported / used at all in the current
U-Boot mainline source tree any more. So lets remove the core u8500 code
and code that was only referenced by this platform.
Please note that this patch also removes these config options:
- CONFIG_PL011_SERIAL_RLCR
- CONFIG_PL011_SERIAL_FLUSH_ON_INIT
As they only seem to be referenced by u8500 based boards. Without any
such board in the current code, these config option don't make sense
any more. Lets remove them as well.
If someone still wants to use this platform, then please send patches
to re-enable support by adding at least one board that references this
code.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: John Rigby <john.rigby@linaro.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add imx7d basic SoC system support
Misc arch dependent functions for system bring up
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
* Add Clock control module (CCM) support
* iMX7D SoC introduces 3 main clock sysmtem abstraction for clock
root frequency generation denominated clock slices.
Core clock slice: hihg speed clock for ARM core
Bus clock slice: for bus clocks
IP clock slice: Peripheral clocks
* At system boot ROM enables PLL_ARM, PLL_DDR, PLL_SYS, PLL_ENET
In u-boot, we have to:
- Configure PFD3- PFD7 for freq we needed in u-boot
- Set clock root for peripherals (ip channel)
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
* Add system arch level header files
- imx-regs.h: iMX7D SoC system architecture registers
- crm_regs.h: Clock control module registers
- sys_proto.h: helper callback function for SoC setup
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
Add system counter driver for imx7d and mx6ul
imx7 and imx6ul supports system counter timer as well as
GPT timer (arch/arm/imx-common/timer.c); The default for
imx7 is systemcounter timer.
Signed-off-by: Ye.Li <B37916@freescale.com>
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Move common imx6 arch init setup, init.c can be extended
and reused to support imx7 SoC keeping init arch common
code.
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
The current simplify lpc32xx gpio driver implementation assume a
maximum of 32 GPIO per port; there are a total of 22 GPI, 24 GPO
and 6 GPIO to managed on port 3.
Update the driver to fix the following:
1) When requesting GPI_xx and GPO_xx on port 3 (xx is the same number)
the second call to "gpio_request" will return -EBUSY.
2) The status of GPO_xx pin report the status of the
corresponding GPI_xx pin when using the "gpio status" command.
3) The gpio driver may setup the direction register for the wrong
gpio when calling "gpio_direction_input" (GPI_xx) or
"gpio_direction_output" (GPO_xx) on port 3; the call to the
direction is require to use the "gpio status" command.
The following change were done in the driver:
1) port3 GPI are cache in a separate 32 bits in the array.
2) port3 direction register written only for GPIO pins.
3) port3 GPO & GPIO (as output) are read using "p3_outp_state".
4) LPC32XX_GPI_P3_GRP updated to match the change.
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
introduce BIT() definition, used in at91_udc gadget
driver.
Signed-off-by: Heiko Schocher <hs@denx.de>
[remove all other occurrences of BIT(x) definition]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
This patch adds the "nandecc" command to switch between the SPEAr600 internal
1-bit HW ECC and the 4-bit SW BCH4 ECC. This can be needed to support NAND
chips with a stronger ECC than 1-bit, as on the x600. And to dynamically
switch between both ECC schemes for backwards compatibility.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
These boards have not been converted to generic board by the deadline.
Remove all cpu9260 and cpuat91 boards.
Signed-off-by: Simon Glass <sjg@chromium.org>
Because there is an originally defined CLK_DMA_ENABLE macro in clk.h,
no reason to add another DMA_CLK_ENABLE macro with the same value.
Remove DMA_CLK_ENABLE, since it does not follow naming convention from
the code, this implies renaming of DMA_CLK_ENABLE to CLK_DMA_ENABLE in
lpc32xx/devices.c file.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Tested-by: Sylvain Lemieux <slemieux@tycoint.com>
Add a SPI driver for the Rockchip RK3288, using driver model. It should work
for other Rockchip SoCs also.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add an I2C driver for the Rockchip RK3288, using driver model. It should work
for other Rockchip SoCs also.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add code to set up the SDRAM in SPL, ready for loading U-Boot. This uses
device tree for configuration so should be able to support other RAM
configurations. It may be possible to generalise the code to support other
SoCs at some point.
Signed-off-by: Simon Glass <sjg@chromium.org>
PMU is the power management unit and GRF is the general register file. Both
are heavily used in U-Boot. Add header files with register definitions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add header files for the peripherals and clocks supported on Rockchip
platforms. The particular implementation (and register set) for each is
SoC-specific, but it seems that the naming can be generic.
Signed-off-by: Simon Glass <sjg@chromium.org>
Since we need to support runtime check for different drivers, we need
to add get_cpu_rev for vf610, otherwise there will be build errors.
This patch introduces a dummy CPU id which is not read from chip
silicon. Later when we can get the real id from chip, can fix the
value of MXC_CPU_VF610 then.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Suggested-by: Stefano Babic <sbabic@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
There is a hole in shadow registers address map of size 0x100
between bank 5 and bank 6 on iMX6QP, iMX6DQ, iMX6SDL, iMX6SX and iMX6UL.
Bank 5 ends at 0x6F0 and Bank 6 starts at 0x800. When reading the fuses,
we should account for this hole in address space.
Similar hole exists between bank 14 and bank 15 of size
0x80 on iMX6QP, iMX6DQ, iMX6SDL and iMX6SX.
Note: iMX6SL has only 0-7 banks and there is no hole.
Note: iMX6UL doesn't have this one.
When reading, we use register offset, so need to account for holes
to get the correct address.
When writing, we use bank/word index, there is no need to account
for holes, always use bank/word index from fuse map.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Add LPDDR2 support:
1. Implement a function mx6_lpddr2_cfg to initialize MMDC for LPDDR2.
2. Introduce a structure mx6_lpddr2_cfg, most entrys are same to
mx6_ddr3_cfg, but still keep it a single one for easy to choose
parameters for LPDDR2.
3. If ddr_type is LPDDR2, use mx6_lpddr2_cfg to init MMDC.
4. Update comments.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
To i.MX6, DDR3 and LPDDR2 is supported, so rename function mx6_dram_cfg
to mx6_ddr3_cfg and the original mx6_dram_cfg function only is a wrapper.
The new reimplemented function mx6_dram_cfg only invokes mx6_ddr3_cfg
when ddr_type is for DDR3. Later we can use ddr_type to initialize
MMDC for LPDDR2.
Initialize ddr_type for different boards which enable SPL.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Add ddr_type entry for mx6_ddr_sysinfo. It will be used for
differenrate DDR3 and LPDDR2.
Introduce an enum type for ddr_type.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Add mpzqlp2ctl entry for mx6_mmdc_calibration.
MMDC_MPZQLP2CTL register is for init tZQINIT, tZQCL, tZQCS for LPDDR2 chips.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Define two structure mx6sl_iomux_ddr_regs and mx6sl_iomux_grp_regs.
Add a new function mx6sl_dram_iocfg to configure dram io.
Add header file to define macros for register address.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
* Add mxc_gpio support for imx7d SoC
* Use CONFIG_MX7 to extend mxc gpio driver support for imx7d
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
* Add imx7d support for iomux controller
* imx7d has two iomux controllers iomuxc (0x3033000) and iomuxc-lpsr
(0x302C0000) each conroller provides control and mux mode pad
registers but shares iomuxc input select register with iomuxc-lpsr
IOMUX_CONFIG_LPSR flag is used to properly set daisy chain settings
for iomuxc-lpsr pads.
* Since mx7d introduces LPSR IOMUX pins, add new base to IOMUX v3
driver for these LPSR pins.
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
To i.MX6SX/UL, two ethernet interfaces are supported.
Add ENET2 clock support:
1. Introduce a new input parameter "fec_id", only 0 and 1 are allowed.
To value 1, only i.MX6SX/UL can pass the check.
2. Modify board code who use this api to follow new api prototype.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Nikolaos Pasaloukos <Nikolaos.Pasaloukos@imgtec.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Move most macro definitions and prototypes into
"arch/arm/include/asm/imx-common/sys_proto.h" to avoid duplicated
function prototypes and marco definitions for different i.MX SoCs.
This patch do not remove the sys_proto.h for different i.MX SoCs,
because we need to modify lots of driver code and others. This patch
remove duplicated macros and prototypes and incude "sys_proto.h"
of imx-common for each sys_proto.h of different i.MX platforms.
Then later we should avoid add stuff in sys_proto.h of each platform,
and modify driver to include common sys_proto.h.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Rewrite get_cpu_rev, from "static const char *get_cpu_rev(void)" to
"u32 get_cpu_rev(void)". To align with get_cpu_rev of other i.MXes.
Also write get_imx_type to replace get_cpu_type, since we have
macro named get_cpu_type.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Use new formula for get_cpu_rev, since we need to use this formula
to do runtime check for all i.MXes.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
This commit adds ethernet support to the TS4800. Note that the
MAC address is not fused on this board and have to be read from
FEC PALR PAUR registers (this is how the kernel provided by
Technologic Systems does it).
signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Cc: Stefano Babic <sbabic@denx.de>
This patch rewrites MMU translation table entries. To start, all table
entries are written as "invalid", then "device-ngnrnr" and "normal" are
written to the entries to enable access to specific addresses.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
DEVDISRn registers provides a mechanism for gating clocks of IP blocks
that are not used. Here we implement hwconfig option to allow users
to disable unused peripherals on the board.
For ex. If eSDHC/qDMA/eDMA are unused and with disabled status in dts,
User can enable CONFIG_FSL_DEVICE_DISABLE and set "devdis:esdhc,qdma,edma"
in hwconfig, thus ESDHC controller & eDMA/qDMA will be clock gated to
save more power.
Signed-off-by: Zhuoyu Zhang <Zhuoyu.Zhang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Replace the DMACTRL[LE] hack with recommended settings
for ETSECDMAMCR to get the same end effect - obtaining
big-endian buffer descriptors and frame data for eTSEC.
The reset / default value for ETSECDMAMCR is preserved,
excepting the BD and FR bits which are cleared to enable
the BE mode in accordance with the H/W specifications.
Fixes: 52d00a8 "ls102xa: etsec: Add etsec support for LS102xA"
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Acked-by: Alison Wang <alison.wang@freescale.com>
Tested-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
ISBC Key Extension feature is not applicable for RAMBOOT
as there is no way to retrieve the CSF Header and validated
IE Key table from SRAM once CPC has been disabled.
The feature is only applicable in case of NOR SECURE BOOT.
Code Cleanup:
The SECURE_BOOT specific defines have been moved from
arch-ls102xa/config.h to
arm/include/asm/fsl_secure_boot.h
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds a minimal framework for Dickens CCN-504
interconnect configuration - mainly related to adding Clusters/cores
to snoop/DVM domain and setting QoS of the RN-I ports.
LS2085A platform makes use of these configurations to support
better network data performance and to boot a SMP Linux.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
add SCIFA port base offsets
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
On the A31s the RTC is by default secured. Thus when u-boot
loads the kernel in non-secure world, the RTC is unavailable. The
SoC has a TrustZone Protection Controller, which can be used to
enable non-secure access to the RTC.
On the A31 the TZPC doesn't seem to do anything, i.e. changes to
its register contents do not affect access to the RTC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Added functions to enable and disable USB clocks which can be invoked
during USB init and USB exit respectively.
Cc: Roger Quadros <rogerq@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Added functions to enable and disable USB clocks which can be invoked
during USB init and USB exit respectively.
Cc: Roger Quadros <rogerq@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Implemented board_usb_init(), board_usb_cleanup() and
usb_gadget_handle_interrupts() in omap5 board file that
can be invoked by various gadget drivers.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Implemented board_usb_init(), board_usb_cleanup() and
usb_gadget_handle_interrupts() in beagle_x15 board file that
can be invoked by various gadget drivers.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enabled clocks for the second dwc3 controller and second USB PHY present in
DRA7.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The SPL implementation for SPEAr600 is older than the common SPL
infrastructure. This patch now moves the SPEAr600 SPL over to the
common SPL code.
Tested on the only SPEAr board that currently uses SPL in mainline
U-Boot, the x600.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Vipin Kumar <vk.vipin@gmail.com>
DP83865 ethernet phy used on DRA74x-evm is quirky and the datasheet
provided IODELAY values for standard RGMII phys do not work.
Silicon Revision(SR) 2.0 provides an alternative bit configuration
that allows us to do a "gross adjustment" to launch the data off a
different internal clock edge. Manual IO Delay overrides are still
necessary to fine tune the clock-to-data delays. This is a necessary
workaround for the quirky ethernet Phy we have on the platform.
NOTE: SMA registers are spare "kitchen sink" registers that does
contain bits for other workaround as necessary as well. Hence the
control for the same is introduced in a generic SoC specific, board
generic location.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add support for detection of ES2.0 version of DRA7 family of
processors. ES2.0 is an incremental revision with various fixes
including the following:
- reset logic fixes
- few assymetric aging logic fixes
- MMC clock rate fixes
- Ethernet speed fixes
- edma fixes for mcasp
[ravibabu@ti.com: posted internal for an older bootloader]
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
If ecc chunk data size is 512 and oobsize is bigger than 512, there is
a chance that block_mark_bit_offset conflicts with bch ecc area.
The following graph is modified from kernel gpmi-nand.c driver with
each data block 512 bytes. We can see that Block Mark conflicts with
ecc area from bch view. We can enlarge the ecc chunk size to avoid
this problem to those oobsize which is larger than 512.
| P |
|<----------------------------------------------------------------->|
| |
| (Block Mark) |
| P' | | | |
|<--------------------------------------------------->| D | | O'|
| |<--------->| |<->|
V V V V V
+---+--------------+-+--------------+-+--------------+-+----------+-+---+
| M | data |E| data |E| data |E| data |E| |
+---+--------------+-+--------------+-+--------------+-+----------+-+---+
^ ^
| O |
|<---------------->|
P : the page size for BCH module.
E : The ECC strength.
G : the length of Galois Field.
N : The chunk count of per page.
M : the metasize of per page.
C : the ecc chunk size, aka the "data" above.
P': the nand chip's page size.
O : the nand chip's oob size.
O': the free oob.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Tested-By: Tim Harvey <tharvey@gateworks.com>
This patch moves pxa to the common timer functions added in commit
8dfafdd - Introduce common timer functions <Rob Herring>
The (removed) pxa timer code (specifically __udelay()) could deadlock at
the 32-bit boundary of get_ticks(). get_ticks() returned a 32-bit value
cast up to a 64-bit value. If get_ticks() + tmo in __udelay() crossed
the 32-bit boundary, the while condition became unconditionally true and
locked the processor. Rather than patch the specific pxa issues, simply
move everything over to the common code.
Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsuiko.com>
USB EHCI on SPEAr600 has not been tested for a while. The base controller
addresses are missing. This patch adds the defines to the header. And adds
the missing code.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Vipin Kumar <vk.vipin@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Added usb dwc3 driver support for zynqmp
this also supports the DFU and LTHOR to download
the linux images on to RAM and cen be booted from
those linux images.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The change adds a number of macro definitions used by USB OHCI driver,
if CONFIG_USB_OHCI_LPC32XX is selected from a board config file.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Tested-by: Sylvain Lemieux <slemieux@tycoint.com>
Incorporate USB driver from legacy LPCLinux NXP BSP.
The files taken from the legacy patch are:
- lpc32xx USB driver
- lpc3250 header file USB registers definition.
The legacy driver was updated and clean-up as part of the integration with the latest u-boot.
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Vladimir Zapolskiy <vz@mleia.com>
A number of LPC32xx SLC NAND defines is dictated by controller
hardware limits and OOB layout is defined by operating system, the
definitions are common for all users. Since those macro are used
in out of NAND SLC driver code (simple NAND SPL framework), they can
not be placed into the driver, therefore move them from board config
files to arch/config.h
The change also adds OOB layout details specific to small page NAND
devices taken from Linux kernel.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Tested-by: Sylvain Lemieux <slemieux@tycoint.com>
Incorporate DMA driver from legacy LPCLinux NXP BSP.
The files taken from the legacy patch are:
- lpc32xx DMA driver
- lpc3250 header file DMA registers definition.
The legacy driver was updated and clean-up as part of the integration with the latest u-boot.
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Vladimir Zapolskiy <vz@mleia.com>
Enable TI_EDMA3 and SPL_DMA support, so as to reduce boot time. With
DMA enabled there is almost 3x improvement in read performance. This
helps in reducing boot time in qspiboot mode
Also add EDMA3 base address for DRA7XX and AM57XX.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Adds functions to enable and disable edma3 clocks which can be invoked
by drivers using edma3 to control the clocks.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Add do_disable_clocks() to disable clock domains and module clocks.
These clocks are enabled using do_enable_clocks().
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Add do_disable_clocks() to disable clock domains and module clocks.
These clocks are enabled using do_enable_clocks().
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Add missing registers in struct definition.
Update GPIO MUX base register to match GPIO base (refer to "LPC32x0 User manual" Rev. 3 - 22 July 2011).
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Move arch/arm/cpu/armv7/exynos/* to arch/arm/mach-exynos/* to allow
reuse of existing code for ARMv8 based Exynos platforms.
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add support for the mipi pll, this is necessary for getting higher dotclocks
with lcd panels.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The tv-encoder on sun5i is slightly different compared to the one on
sun4i/sun7i.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
This header file uses type definitions (u8, u32) from linux/types.h but
doesn't include it. If includes aren't carefully ordered this can cause
build failures.
Cc: Tom Warren <twarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add defines to allow reading recovery mode (RCM) boot type from the boot
information table (BIT) written by the boot ROM (BR) to the IRAM.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The "method" parameter was part of the original port of the driver from
the kernel. At some point this may have been added to allow for future
differentiation (as omap1 and omap2 have different GPIO IP blocks, so
this wasn't an unreasonable thing to do). At this point however it's
just extra overhead, so drop.
Signed-off-by: Tom Rini <trini@konsulko.com>
AM43XX SoCs support up to 192 GPIO signals.
Make this amount available to the driver.
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
This patch adds the glue code for hi6220 SoC which has 2x synopsis
dw_mmc controllers. This will be used by the hikey board support
in subsequent patches.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds the header files which will be used in the subsquent
board / drivers to enable support for hi6220 hikey board.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
gpio.h - Added missing copyright in few files.
rsa-mod-exp.h - Corrected copyright in the file.
fsl_sec.h - Added missing license in files
drivers/crypto/fsl/Makefile - Removed the incomplete GPLv2 license and replaced it with GPLv2+ license
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Reboot mode is written in scratchpad memory before reboot in the form of a
single char, that is the first letter of the reboot mode string as passed to the
reboot function.
This mechanism is supported on OMAP3 both my the upstream kernel and by various
TI kernels.
It is up to each board to make use of this mechanism or not.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
The change adds support of LPC32xx SLC NAND controller.
LPC32xx SoC has two different mutually exclusive NAND controllers to
communicate with single and multiple layer chips.
This simple driver allows to specify NAND chip timings and defines
custom read_buf()/write_buf() operations, because access to 8-bit data
register must be 32-bit aligned.
Support of hardware ECC calculation is not implemented (data
correction is always done by software), since it requires a working
DMA engine.
The driver can be included to an SPL image.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Tested-by: Sylvain Lemieux <slemieux@tycoint.com>
Enable BCM SF2 ethernet and PHY for BCM Cygnus SoC
Signed-off-by: Jiandong Zheng <jdzheng@broadcom.com>
Signed-off-by: Steve Rae <srae@broadcom.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
add support for the at91sam9260 based board smartweb from
siemens. SPL is used without serial support, as this
SoC has only 4k sram for running SPL. Here a U-Boot
bootlog:
RomBOOT
>
U-Boot 2015.07-rc2-00109-g4ae828c (Jun 15 2015 - 09:31:16 +0200)
CPU: AT91SAM9260
Crystal frequency: 18.432 MHz
CPU clock : 198.656 MHz
Master clock : 99.328 MHz
Watchdog enabled
DRAM: 64 MiB
WARNING: Caches not enabled
NAND: 256 MiB
In: serial
Out: serial
Err: serial
Net: macb0
Hit any key to stop autoboot: 0
U-Boot>
Signed-off-by: Heiko Schocher <hs@denx.de>
Add a few extra sunxi display registers and constant defines.
Also rename some existing defines (e.g. dropping _GCTRL) and make
some more generic (e.g. dropping the 2x scaling from
SUNXI_LCDC_TCON1_TIMING_V_TOTAL).
This is a preparation patch for adding composite video out support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
USB devices are not really designed to get the power bounced off and on
at them. Esp. USB powered harddisks do not like this.
Currently we power off the USB ports both on a "usb reset" and when
booting the kernel, causing the usb-power to bounce off and then back
on again.
This patch removes the powering off calls, fixing the undesirable power
bouncing.
Note this requires some special handling for the OTG port:
1) We must skip the external vbus check if we've already enabled our own
vbus to avoid false positives
2) If on an usb reset we no longer detect that the id-pin is grounded, turn
off vbus as that means an external vbus may be present now
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
To enable NAND flash in sunxi SPL,
pins 0-6, 8-22 and 24 on port C are configured.
Signed-off-by: Karol Gugala <kgugala@antmicro.com>
Signed-off-by: Piotr Zierhoffer <pzierhoffer@antmicro.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
T124/210 requires some specific configuration (VPR setup) to
be performed by the bootloader before the GPU can be used.
For this reason, the GPU node in the device tree is disabled
by default. This patch enables the node if U-boot has performed
VPR configuration.
Boards enabled by this patch are T124's Jetson TK1 and Venice2
and T210's P2571.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Tom Warren <twarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
U-boot is responsible for enabling the GPU DT node after all necessary
configuration (VPR setup for T124) is performed. In order to be able to
check whether this configuration has been performed right before booting
the kernel, make it happen during board_init().
Also move VPR configuration into the more generic gpu.c file, which will
also host other GPU-related functions, and let boards specify
individually whether they need VPR setup or not.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Tom Warren <twarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
