Board is using kv260 design for couple of parts defined by spec like i2c
eeproms, ina260, uart, etc.
Board has 4 gems. One gem connected via PS SGMII(GT), another PS RGMII(MIO)
and 2 via EMIO. First two shares the same MIO lines for PHYs. PL based one
have separate EMIO lines via PL.
Also two USB 3.0 with usb hubs are present. USB phys and USB hubs should
have separate reset line. The first usb0 hub also has USB-SD controller
(usb2244) connected to port 0.
To test compatibility with k26 you can run:
fdtoverlay -o /tmp/output.dtb -i arch/arm/dts/zynqmp-sm-k26-revA.dtb \
arch/arm/dts/zynqmp-sck-kr-g-revA.dtbo
Also add support for kr260-revB board. Based on FRU it is revision B
but schematics can be label as revA03.
Changes in revB are:
- SFP light
- GEM2/3 TX_CLK fixes
- PMOD/RPI connector fixes
- Replace si5332 with oscilators
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/dac2ee1826e73b89c8cc1e430354eb43d291f675.1652870941.git.michal.simek@amd.com
This was previously needed, but U-Boot is now capable of parsing
the new "phy-connection-type" property that is already used in
the main devicetree.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
This syncs the devicetree files with the latest Linux kernel (5.19-rc2).
This also fixes the currently broken ethernet support:
Before:
Net: Could not get PHY for FEC0: addr 0
After:
Net: eth0: ethernet@30be0000
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The HPE SoC is new to linux. A basic device tree layout with minimum
required for linux to boot including a timer and watchdog support has
been created.
The dts file is empty at this point but will be updated in subsequent
updates as board specific features are enabled.
Signed-off-by: Nick Hawkins <nick.hawkins@hpe.com>
Seems that u-boot can't probe i2c bus at 2.6Mhz speed, so lower
the speed to the default value 100Khz.
v2: fix i2c1 frequency in the root omap3-u-boot.dtsi include.
Signed-off-by: Anthoine Bourgeois <anthoine.bourgeois@gmail.com>
- Correct livetree support in stm32mp1 boards
- Activate livetree for stm32mp15 DHSOM boards
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAmKsehgACgkQ4rK92eCq
k3UexAf+JThCd7FlN3OkTVKIdZKeNm2KpQxrqt20whiqp/nSUzxXrjdlCTKZEER2
lLJoVnwr+bkmdlqsa6gAZXSsd0lUv37XnLsLA5or278tFNlKp6gzYrz49FR59mVC
ie7/NlY5FgM5qmKGCob7tjwJ78r2/S3T2EaLiAMWUmw2UB5KZU6h3napHZ+1T0se
vaEAVRzAaZeYzKU3k6RBSv2tXQ6ssvfpp9RcXpRGtrN908AqDhHiOfntuOrnsEe0
9rjY1DSXO9a5WqHRm2KQ3FrA/By2layQ+4WH/HgIPHasisnmo3E/euVWmhtTaiT/
g5bOLwyFQ2/RvdMlMxXlKUcuMfNwRA==
=Hhzj
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20220620' of https://source.denx.de/u-boot/custodians/u-boot-stm into next
- Add STM32MP13 SoCs support with associated board STM32M135F-DK
- Correct livetree support in stm32mp1 boards
- Activate livetree for stm32mp15 DHSOM boards
This adds an SFP binding for the processors it is present on. I have
only tested this for the LS1046A.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
QorIQ platforms now use different clock bindings. Although we don't use
the device tree for clocks on this platform, it is helpful to sync it
because then the bindings will more closely match Linux. Additionally,
it allows for using more clock fractions (such as platform/4).
This corresponds to Linux commit b6f5e7019391 ("ARM: dts: ls1021a:
update the clockgen node").
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Compile the device tree of STM32MP13x boards and add the needed
U-Boot add-on.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The freeze controller is required for FPGA partial reconfig.
This node is disable on default.
Enable this node via u-boot fdt command when needed.
Signed-off-by: Yau Wai Gan <yau.wai.gan@intel.com>
Signed-off-by: Dinesh Maniyam <dinesh.maniyam@intel.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@intel.com>
The freeze controller is required for FPGA partial reconfig.
This node is disable on default.
Enable this node via u-boot fdt command when needed.
Signed-off-by: Yau Wai Gan <yau.wai.gan@intel.com>
Signed-off-by: Dinesh Maniyam <dinesh.maniyam@intel.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@intel.com>
Add initial support of STM32MP13 family based on v5.18-rc2
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add DT for DH DRC Compact unit, which is a universal controller device.
The system has two ethernet ports, one CAN, RS485 and RS232, USB, uSD
card slot, eMMC and SDIO Wi-Fi.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add another mux option for SPI2 pins, this is used on DRC Compact board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add another mux option for CAN1 pins, this is used on DRC Compact board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add another mux option for UART5 pins, this is used on DRC Compact board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add another mux option for UART4 pins, this is used on DRC Compact board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add another mux option for UART3 pins, this is used on DRC Compact board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
With the move to use DM_CLK the boards uart stops working. The used
properties are not supported by the imx8mq clock driver. Thus
the correct baudrate cannot be selected. Remove this properties here and
the board can start with working uart. Keep it in the main dts because
linux handles these porperties fine.
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
This new MMC sample select value is obtained from running
tests on multiple Stratix 10 boards and proven working.
Signed-off-by: Yau Wai Gan <yau.wai.gan@intel.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@intel.com>
Mark pinctrl_wdog as u-boot,dm-spl to clean up board code,
The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Mark wdog1/pinctrl_wdog as u-boot,dm-spl to clean up board code,
The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Mark pinctrl_wdog as u-boot,dm-spl to clean up board code,
The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Mark pinctrl_wdog as u-boot,dm-spl to clean up board code,
The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Mark pinctrl_wdog as u-boot,dm-spl to clean up board code,
The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Mark pinctrl_wdog as u-boot,dm-spl to clean up board code,
The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The Cubox has an unstable phy address - which can appear at either
address 0 (intended) or 4 (unintended).
SoM revision 1.9 has replaced the ar8035 phy with an adin1300, which
will always appear at address 1.
Change the reg property of the phy node to the magic value 0xffffffff,
which indicates to the generic phy driver that all addresses should be
probed. That allows the same node (which is pinned by phy-handle) to match
either the AR8035 PHY at both possible addresses, as well as the new one
at address 1.
Also add the new adi,phy-output-clock property for enabling the 125MHz
clock used by the fec ethernet controller, as submitted to Linux [1].
Linux solves this problem differently:
For the ar8035 phy it will probe both phy nodes in device-tree in order,
and use the one that succeeds. For the new adin1300 it expects U-Boot to
patch the status field in the DTB before booting
While at it also sync the reset-delay with the upstream Linux dtb.
[1] https://patchwork.kernel.org/project/netdevbpf/patch/20220428082848.12191-4-josua@solid-run.com/
Signed-off-by: Josua Mayer <josua@solid-run.com>
The generated flash.bin does not boot the imx8mn evk LPDDR4 variant
as it misses the spl.bin description in binman.
Add its entry to fix the boot on the imx8mn evk LPDDR4 variant.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Tested-by: Arti Zirk <art@zirk.me>
Reviewed-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
AM62 StarterKit (SK) board is a low cost, small form factor board
designed for TI’s AM625 SoC. It supports the following interfaces:
* 2 GB DDR4 RAM
* x2 Gigabit Ethernet interfaces capable of working in Switch and MAC mode
* x1 HDMI Port with audio + x1 OLDI/LVDS Display interface for Dual Display
* x1 Headphone Jack
* x1 USB2.0 Hub with two Type A host and x1 USB Type-C DRP Port
* x1 UHS-1 capable µSD card slot
* 2.4/5 GHz WLAN + Bluetooth 4.2 through WL1837
* 512 Mbit OSPI flash
* x4 UART through UART-USB bridge
* XDS110 for onboard JTAG debug using USB
* Temperature sensors, user push buttons and LEDs
* 40-pin User Expansion Connector
* 24-pin header for peripherals in MCU island (I2C, UART, SPI, IO)
* 20-pin header for Programmable Realtime Unit (PRU) IO pins
* 15-pin CSI header
Add basic support for AM62-SK.
To keep the changes to minimum. Only UART And SD are supported at the
moment. This should serve as good example for adding new board support
based on AM62x SoC
Schematics: https://www.ti.com/lit/zip/sprr448
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
For dfu boot mode, the clocks property needs to be deleted and dr_mode
needs to be set to peripheral. Therefore, add the required fixes for the
same.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
This is the initial support for Broadcom's ARM-based 47622 SOC.
In this change, our first SOC is an armv7 platform called 47622. The
initial support includes a bare-bone implementation and dts with ARM
PL011 uart.
The SOC-specific code resides in arch/arm/mach-bcmbca/<soc> and board
related code is in board/broadcom/bcmba.
The u-boot image can be loaded from flash or network to the entry
point address in the memory and boot from there.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Kursad Oney <kursad.oney@broadcom.com>
Signed-off-by: Anand Gore <anand.gore@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
Add wkup_gpio pinmux setting which will be used for performing the
DT fixup for hbmc node according to mux selection state, on J721E
EVM, hypermux sel is tied to ·WKUP_GPIO0_8.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Add DT node for HyperBus Memory Controller and hbmc-mux in the
FSS. hbmc-am654 driver uses syscon_get_regmap() call which fails
with current compatible setting.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Since commit dffdb1f8eb ("board: ti: am64x: Use fdt functions
for ram and bank init") ddr_init() and dram_bank_init() have
switched to fdtdec for getting the memory configuration from
the am64xx dts files instead of using hardcoded values. This
requires an accessible memory node in SPL as we already have
in k3-am642-r5-evm.dts.
Make the memory node accessible in A53 SPL for both am642-sk
and am642-evm and in am642-sk R5 SPL.
Signed-off-by: Georgi Vlaev <g-vlaev@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
zynqmp:
- Fix DP PLL configuration for zcu102/zcu106 and SOM
- Fix split mode for starting R5s
- DT fixes
- Remove firmware node for mini configurations
- Wire TEE for multi DTB fit image
xilinx:
- Handle board_get_usable_ram_top(0) properly
phy:
- Extend psgtr timeout
mmc:
- Fix mini configuration which misses zynqmp_pm_is_function_supported()
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYo4bYwAKCRDKSWXLKUoM
IYmTAJ9t4GDXggJ7ErB3Kk7/qSrywjEGAgCgnKQVgQvjo1B6o5aiwbk1wR86zkQ=
=W7X8
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.07-rc4' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2022.07-rc4
zynqmp:
- Fix DP PLL configuration for zcu102/zcu106 and SOM
- Fix split mode for starting R5s
- DT fixes
- Remove firmware node for mini configurations
- Wire TEE for multi DTB fit image
xilinx:
- Handle board_get_usable_ram_top(0) properly
phy:
- Extend psgtr timeout
mmc:
- Fix mini configuration which misses zynqmp_pm_is_function_supported()
The bulk of it is (finally!) some DT sync from the kernel. We refrained
from syncing one incompatible change, as this would spoil booting Linux
kernels before v5.13 with U-Boot's DT (via UEFI, for instance).
I test booted Linux v5.18 and v5.4 with that new DT on some boards, and
the headless peripherals (MMC, USB, Ethernet) seemed to work.
The rest are fixes:
- silencing missing clock warnings due to the new pinctrl driver
- fixing "UART0 on PortF", allowing UART access through the SD card pins
- add an F1C100s clock driver, to enable MMC support (SPI comes later)
- some cleanups for CONS_INDEX_n in Kconfig
Tested on BananaPi-M1, Pine64-LTS, Pine-H64, X96-Mate (H616) and
OrangePi-Zero.
Use the de10-nano files as templates for the de10-standard board.
The files in qts directory are generated by quartus from the GHRD
design.
Signed-off-by: Humberto Naves <hsnaves@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Add support for DH electronics i.MX8M Plus DHCOM SoM on PDK2 carrier board.
Currently supported are serial console, EQoS and FEC ethernets, eMMC, SD,
SPI NOR and USB 3.0 host.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
The initial U-Boot F1C100s port was based on the mainline kernel DT
files, which were quite basic and were missing the essential MMC and
SPI peripherals. While we could work around this in the SPL by
hardcoding the required information, this left U-Boot proper without SD
card or SPI flash support, so actual loading would require FEL boot.
Now the missing DT bits have been submitted and accepted in the kernel
tree, so lets sync back those files into U-Boot to enable MMC and
SPI, plus benefit from some fixes.
This is a verbatim copy of the .dts and .dtsi file from
linux-sunxi/dt-for-5.19[1], which have been part of linux-next for a
while as well.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux.git/log/?h=sunxi/dt-for-5.19
Link: https://lore.kernel.org/linux-arm-kernel/20220317162349.739636-1-andre.przywara@arm.com/
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Copy the devicetree source for the H6 SoC and all existing boards
from the Linux v5.18-rc1 tag.
To maintain ABI compatibility with existing LTS kernels, one change
moving some IP blocks to the r_intc interrupt controller is excluded.
This effectively reverts Linux commits 189bef235dd3 and 73088dfee635.
This commit also adds the following new board devicetrees:
- sun50i-h6-pine-h64-model-b.dts
- sun50i-h6-tanix-tx6-mini.dts
This update should not impact any existing U-Boot functionality.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Copy the devicetree source for the A64 SoC and all existing boards
from the Linux v5.18-rc1 tag.
To maintain ABI compatibility with existing LTS kernels, one change
moving some IP blocks to the r_intc interrupt controller is excluded.
This effectively reverts Linux commits 189bef235dd3 and 73088dfee635.
This update should not impact any existing U-Boot functionality.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Copy the devicetree for the R40/T3 SoC verbatim from the Linux v5.18-rc1
tag. None of the existing boards had any devicetree updates.
This commit adds the following new board devicetrees:
- sun8i-r40-oka40i-c.dts
- sun8i-t3-cqa3t-bv3.dts
Signed-off-by: Samuel Holland <samuel@sholland.org>
Copy the devicetree source for the V3(s)/S3 SoCs and all existing boards
verbatim from the Linux v5.18-rc1 tag.
This commit also adds the following new board devicetrees:
- sun8i-s3-elimo-initium.dts
- sun8i-v3-sl631-imx179.dts
This update should not impact any existing U-Boot functionality.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Copy the devicetree source for the H2+/H3/H5 SoCs and all existing
boards from the Linux v5.18-rc1 tag.
To maintain ABI compatibility with existing LTS kernels, one change
moving some IP blocks to the r_intc interrupt controller is excluded.
This effectively reverts Linux commits 994e5818392c and 9fdef3c3d8c2.
This commit also adds the following new board devicetree:
- sun8i-h3-nanopi-r1.dts
This update should not impact any existing U-Boot functionality.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Copy the devicetree source for the A83T SoC and all existing boards
from the Linux v5.18-rc1 tag.
To maintain ABI compatibility with existing LTS kernels, one change
moving some IP blocks to the r_intc interrupt controller is excluded.
This effectively reverts Linux commits 994e5818392c and 9fdef3c3d8c2.
As with the other SoCs, updates of note include adding detection GPIO
properties in the USB PHY nodes.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Copy the devicetree source for the A80 SoC and all existing boards
verbatim from the Linux v5.18-rc1 tag.
This update should not impact any existing U-Boot functionality.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Copy the devicetree source for the A10s/A13/GR8, A31(s), and A23/A33/R16
SoCs and all existing boards from the Linux v5.18-rc1 tag.
These changes are combined into one commit due to interdependencies:
- The unit addresses were removed from bitbanged I2C buses, which
drives a Kconfig default change. This affects sun5i-a13-utoo-p66.dts
and sun6i-a31-colombus.dts.
- The pinctrl nodes were renamed, including some used by the shared
header sunxi-reference-design-tablet.dtsi.
To maintain ABI compatibility with existing LTS kernels, one change
moving some IP blocks to the r_intc interrupt controller is excluded.
This effectively reverts Linux commits 994e5818392c and 9fdef3c3d8c2.
This commit renames the file sun8i-r16-nintendo-nes-classic-edition.dts
to sun8i-r16-nintendo-nes-classic.dts to match the Linux tree.
This commit also adds the following new board devicetrees:
- sun5i-a13-licheepi-one.dts
- sun5i-a13-pocketbook-touch-lux-3.dts
- sun5i-gr8-evb.dts
- sun8i-a23-ippo-q8h-v1.2.dts
- sun8i-a23-ippo-q8h-v5.dts
- sun8i-a33-et-q8-v1.6.dts
- sun8i-a33-ippo-q8h-v1.2.dts
- sun8i-r16-nintendo-super-nes-classic.dts
As with the other SoCs, updates of note are conversion of GPIO pull-up
from pinconf to GPIO flags and renaming the detection GPIO properties in
the USB PHY nodes.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Copy the devicetree source for the A10 SoC and all existing boards
verbatim from the Linux v5.18-rc1 tag.
This commit also adds the following new board devicetree:
- sun4i-a10-topwise-a721.dts
While this update should not impact any existing U-Boot functionality,
the changes to the USB PHY detection GPIO properties are needed to
convert that driver to use the DM GPIO framework.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Copy the devicetree source for the A20 SoC and all existing boards
verbatim from the Linux v5.18-rc1 tag.
This commit also adds the following new board devicetrees:
- sun7i-a20-haoyu-marsboard.dts
- sun7i-a20-linutronix-testbox-v2.dts
- sun7i-a20-olinuxino-lime-emmc.dts
This update includes changes to the USB PHY detection GPIO properties
which are needed to convert that driver to use the DM GPIO framework.
Signed-off-by: Samuel Holland <samuel@sholland.org>
[Andre: fix Mele M5 U-Boot only DT]
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Add a u-boot dtsi for configuring the FEC node of the DH DRC02.
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Philip Oberfichtner <pro@denx.de>
Add a u-boot dtsi for configuring the FEC node of the DH picoITX.
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Philip Oberfichtner <pro@denx.de>
Firstly the FEC can now use the regulator reg_eth_vio from
imx6qdl-dhcom-som.dtsi instead of defining its own.
Secondly the &fec node is moved to the more generic SoM device tree
file, because it can be used by multiple boards.
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Philip Oberfichtner <pro@denx.de>
Migrate DH picoITX device trees from Linux commit 42226c989789
(tag v5.18-rc7). No changes have been made, the DTs are exact copies.
Furthermore add the DTB to dh_imx6_defconfig.
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Philip Oberfichtner <pro@denx.de>
Migrate DH DRC02 device trees from Linux commit 42226c989789
(tag v5.18-rc7). No changes have been made, the DTs are exact copies.
Furthermore add the DTB to dh_imx6_defconfig.
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Philip Oberfichtner <pro@denx.de>
In the DH electronics iMX6 board file fix the outdated eeprom path by
using a DT label instead.
The label has been newly created for all iMX6QDL DHCOM boards.
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Philip Oberfichtner <pro@denx.de>
The Bosch ACC (Air Center Control) Board is based on the i.MX6D.
The device tree is copied from Linux, see [1]. The only difference
compared to the Linux DT is the removal of usbphynop properties. They are
defined in the Linux version of imx6qdl.dtsi, but not in the u-boot
version.
[1] Commit 6192cf8ac082 from
git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux.git
Signed-off-by: Philip Oberfichtner <pro@denx.de>
Mark pinctrl_wdog as u-boot,dm-spl to clean up board code,
The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Mark pinctrl_wdog as u-boot,dm-spl to clean up board code,
The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Mark pinctrl_wdog as u-boot,dm-spl to clean up board code,
The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Marked related nodes as u-boot,dm-spl for serial driver model
Enable CONFIG_DM_SERIAL
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Marked related nodes as u-boot,dm-spl for serial driver model
Enable CONFIG_DM_SERIAL
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Marked related nodes as u-boot,dm-spl for serial driver model
Enable CONFIG_DM_SERIAL
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Move some common changes to imx8mq-u-boot.dtsi, so others could reuse it
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The MaxLinear GPY111 PHY is being used on some boards due to part
availability. Add support for this PHY which requires a longer reset
post-delay and RGMII delay configuration.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The I2C2 has SMBus device SMSC USB2514Bi connected to it, the device is
capable of up to 100 kHz operation. Reduce the bus frequency to 100 kHz
to guarantee this I2C device can work correctly.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
The Avenger96 board comes in multiple regulator configurations.
- rev.100 or rev.200 have Buck3 preconfigured to 3V3 operation on
boot and contains extra Enpirion EP53A8LQI DCDC converter which
supplies the IO. Reduce Buck3 voltage to 2V9 to not waste power.
- rev.200L have Buck3 preconfigured to 1V8 operation and have no
Enpirion EP53A8LQI DCDC anymore, the IO is supplied from Buck3.
Configure the Buck3 voltage on this board per PMIC NVM settings and
update buck3 voltage limits in DT passed to OS before booting OS to
prevent potential hardware damage.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
BTN_MISC looks like the most reasonable option for this button.
Button is used by firmware to indicate (after reset, power up) that user
wants to do firmware upgrade via firmware update utility.
For bootloader or OS is this just user button which is worth to have it
mapped.
Also button can be used as a wakeup source and pressing it for more time
can generate more chars that's why also adding wakeup-source and autorepeat
properties.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Link: https://lore.kernel.org/r/7f6d627473632c3c3036ec9f6aaa36e00f4615e2.1652262769.git.michal.simek@amd.com
SGMII requires phy to be configured. The support for this has been added to
Linux and U-Boot already that's why also describe the phy via DT. Clock is
coming from si5332 chip (output 1) 125MHz which is only one GT line use on
this board.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/8ad8d0c2fc9690cc90f95feddf87b0e94a685a43.1652262769.git.michal.simek@amd.com
OPP table name now should start with "opp-table" and OPP entries
shouldn't contain commas and @ signs in accordance to the new schema
requirement.
The same change was done in Linux by commit c6d4a8977598 ("ARM: tegra:
Rename CPU and EMC OPP table device-tree nodes"), commit ffbe853a3f5a
("ARM: dts: sunxi: Fix OPPs node name") or commit b7072cc5704d ("arm64:
dts: qcom: qcs404: Rename CPU and CPR OPP tables").
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/a1176349448df35127dbac15c1eeb2229505bae7.1652262769.git.michal.simek@amd.com
In all the ZynqMP boards dts files tx-buswidth is by default set to 1. Due
to this the framework only issues 1-1-1 write commands to the GQSPI driver.
But the GQSPI controller is capable of handling 1-4-4 write commands, so
updated the tx-buswidth to 4 in ZynqMP boards dts files. This would enable
the spi-nor framework to issue 1-4-4 write commands instead of 1-1-1. This
will increase the tx data transfer rate, as now the tx data will be
transferred on four lines instead on single line.
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/ad61199f55e5e00f29de6206d9d1872a52a7657e.1652193179.git.michal.simek@amd.com
STM32 programmer improvements
video: support several LTDC HW versions and fix data enable polarity
board: fix stboard error message, consider USB cable connected when boot device is USB
configs: stm32mp1: set console variable for extlinux.conf
configs: stm32mp1: add support for baudrate higher than 115200 for ST-Link
ARM: stm32mp: Fix Silicon version handling and ft_system_setup()
phy: stm32-usbphyc: Add DT phy tuning support
arm: dts: stm32mp15: alignment with v5.18
ram: Conditionally enable ASR
mach-stm32mp: psci: retain MCUDIVR, PLL3CR, PLL4CR, MSSCKSELR across suspend
configs: Use TFTP_TSIZE on DHSOM and STMicroelectronics boards
ARM: stm32: Use default CONFIG_TFTP_BLOCKSIZE on DHSOM
pinctrl: stm32: rework GPIO holes management
-----BEGIN PGP SIGNATURE-----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=s7xn
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20220510' of https://source.denx.de/u-boot/custodians/u-boot-stm
Add new STM32 MCU boards and Documentation
STM32 programmer improvements
video: support several LTDC HW versions and fix data enable polarity
board: fix stboard error message, consider USB cable connected when boot device is USB
configs: stm32mp1: set console variable for extlinux.conf
configs: stm32mp1: add support for baudrate higher than 115200 for ST-Link
ARM: stm32mp: Fix Silicon version handling and ft_system_setup()
phy: stm32-usbphyc: Add DT phy tuning support
arm: dts: stm32mp15: alignment with v5.18
ram: Conditionally enable ASR
mach-stm32mp: psci: retain MCUDIVR, PLL3CR, PLL4CR, MSSCKSELR across suspend
configs: Use TFTP_TSIZE on DHSOM and STMicroelectronics boards
ARM: stm32: Use default CONFIG_TFTP_BLOCKSIZE on DHSOM
pinctrl: stm32: rework GPIO holes management
The Buck3 on DHCOR is used to supply IO voltage. It can output either 3V3
in the default DHCOR configuration, or 2V9 in case of AV96 DHCOR variant
which has extra Empirion DCDC converter in front of the 1V8 IO supply, or
outright 1V8 in case of 1V8 IO DHCOR without the Empirion DCDC converter.
The 2V9 mode in case of AV96 DHCOR variant is used to reduce unnecessarily
high input voltage to the Empirion DCDC converter, so move it into matching
DTSI to stop confusing users.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Device tree alignment with Linux kernel v5.18-rc2:
- ARM: dts: stm32: Add support for the emtrion emSBC-Argon
(only the pincontrol part)
- ARM: dts: stm32: Drop duplicate status okay from DHCOM gpioc node
- ARM: dts: stm32: add st,stm32-sdmmc2 compatible on stm32mp151
- ARM: dts: stm32: fix AV96 board SAI2 pin muxing on stm32mp15
- ARM: dts: stm32: use exti 19 as main interrupt to support RTC wakeup on
stm32mp157
- ARM: dts: stm32: add DMA configuration to UART nodes on stm32mp151
- ARM: dts: stm32: keep uart4 behavior on *
- ARM: dts: stm32: Correct masks for GIC PPI interrupts on stm32mp15
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
The E4 revision of the AM64 SKEVM embeds a TPS65219 PMIC,
this adds the PMIC node with the required regulators voltages.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
switch the pin definitions from AM33XX_IOPAD to AM33XX_PADCONF macro
Signed-off-by: Gireesh Hiremath <Gireesh.Hiremath@in.bosch.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
In order to be able to get rid of the non-DM MDIO bus registered in
mvneta driver, start using the DM registered one in Turris MOX board
code.
This also allows us to drop the hack introduced in MOX' -u-boot.dtsi
file.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
The Zyxel NSA310s board has the network chip Marvell Alaska 88E1318S.
Use uclass mvgbe and the compatible driver M88E1310 driver to bring
up Ethernet.
- Use uclass mvgbe to bring up the network. And remove ad-hoc code.
- Remove CONFIG_RESET_PHY_R.
- Enable CONFIG_PHY_MARVELL to properly configure the network.
- Add phy mode RGMII to kirkwood-nsa310s.dts
- Miscellaneous changes: Move constants to .c file and remove header file
board/zyxel/nsa310s/nsa310s.h, add support for large USB and SATA HDDs,
use BIT macro, add/cleanup comments, and cosmetic changes.
Note that this patch is depended on the following patch:
https://patchwork.ozlabs.org/project/uboot/patch/20220412201820.10291-1-mibodhi@gmail.com/
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
The impedance of the QSPI PCB lines on the sama7g5ek is 50 Ohms.
Align the output impedance of the QSPI0 HSIOs by setting a medium drive
strength which corresponds to an impedance of 56 Ohms when VDD is in the
3.0V - 3.6V range. The high drive strength setting corresponds to an
output impedance of 42 Ohms on the QSPI0 HSIOs.
This is just a fine tunning. The memory that we have populated on sama7g5ek
works fine even with high drive strength, but it's better to adjust it and
use medium instead, in case some other flashes with higher frequencies are
tested.
Suggested-by: Mihai Sain <mihai.sain@microchip.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
QSPI1 used the clock of QSPI0, fix it.
Fixes: 5eecc37bb1 ("ARM: dts: at91: sama7g5: Add QSPI0 and OSPI1 nodes")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Prepare to use ADC channel 1 to check the hardware revision of the board:
- add u-boot dts include with saradc node
Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20220424082159.757622-6-adeep@lexina.in
Add support for OF-LIST to common imx8mp-u-boot.dtsi so that it can
be used with boards that have multiple DTB's.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Teresa Remmet <t.remmet@phytec.de>
Cc: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Sync BeagleBone dts files & TPS dtsi files with Linux v5.17 and include
the SanCloud BBE Extended WiFi dts added in v5.18-rc1. Also pull in
changes to am33xx-l4.dtsi needed to support the BeagleBone Blue.
The change to use the cpsw switch driver (commit c477358e66a3 in Linux)
is excluded from the sync as u-boot does not recognise the new
compatible string.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
The GW74xx is based on the i.MX 8M Plus SoC featuring:
- LPDDR4 DRAM
- eMMC FLASH
- Gateworks System Controller
- PCIe Gen 3.0 switch (build option)
- USB 3.0 HUB
- USB Type-C front panel connector
- GPS
- 3-axis accelerometer
- CAN bus
- 6x GbE RJ45 front-panel jacks
- 1x IMX8M FEC RGMII GbE (with Passive PoE)
- 5x IMX8M EQOS RGMII 6 port GbE Switch
(1x with 802.3af class 5 Active PoE)
- RS232/RS485/RS422 serial transceiver
- MIPI header (DSI/CSI/GPIO/PWM/I2S)
- DigI/O header (UART/GPIO/I2C/ADC)
- 802.11ac WiFi
- Bluetooth BLE
- 3x MiniPCIe sockets with PCI/USB
- 1x M.2 Socket with USB2.0, PCIe, and dual-SIM
- PMIC
- Wide range DC input supply (8V to 60V DC)
Do the following to add support for this and future imx8mp-venice boards:
- add dts
- add DRAM config
- add PMIC config
- add IMX8MP support in spl.c and venice.c
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The TI DP83867 phy has been replaced with the MaxLinear GPY111 phy
due to part availability. Add support for it:
- increase post-reset time to 300ms per datasheet
- add tx-delay/rx-delay config
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Add gpio hog support for board-specific gpio lines:
- put hogs in u-boot.dtsi so as to keep the regular dts files
in sync with the kernel. The hogs will not be put in the kernel
as that makes them un-usable by userspace as well as
re-initializes them to dt defaults overriding changes which may
have been done by bootloader commands.
- specify gpio names and initial config
- enable GPIO_HOG
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Use the common GSC driver.
This allows us to do some additional cleanup:
- rename gsc{.c,.h} to eeprom{.c.h} for clarity
- collapse eeprom_get_dev
- remove unnecessary header files and alphabatize includes
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Drop Apalis iMX8X platform as it never left sample state and is no
longer supported.
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Add DT bindings for a subset of GPCv2 which handles USB and PCIe PDs,
HSIOMIX PD controller and missing USB PD properties. This is required
to bring up the DWC3 USB controller up.
This is based on linux next and patches which are still pending
review, but which are likely going to be part of Linux 5.19:
b2d67d7bdf74 ("arm64: dts: imx8mp: disable usb3_phy1")
290918c72a29 ("arm64: dts: imx8mp: Add memory for USB3 glue layer to usb3 nodes")
https://www.spinics.net/lists/arm-kernel/msg958501.html
Tested-By: Tim Harvey <tharvey@gateworks.com> #imx8mp-venice-gw74xx
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
DT node name should be generic, therefore rename atsha204a@64 to crypto@64.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
uDPU is a bit of a specific device in that it does not have any copper
ports nor any ethernet PHY-s but 2 SFP ports.
This is an issue since MVNETA requires a PHY phandle or a fixed-link to
be defined under its node.
Since U-boot has no SFP support this is reasonable in order to know how
to configure the MAC.
However this also means that networking does not work on uDPU at all
currently, and fails with:
uDPU>> dhcp
Could not get PHY for neta@30000: addr 0
phy_connect failed
Could not get PHY for neta@40000: addr 1
phy_connect failed
So, to provide working networking using only SFP-s let add the fixed-link
at 1G which is much more common than 2.5G SFP-s as well as disable the
TX_DISABLE pins like done on Armada 7040 and 8040 platforms.
Since uDPU is not using any of the GPIO-s on the SB controller for any
purpose other than GPIO, a call to the pinctrl must be made in order for
it to get probed and thus register the SB GPIO bank, otherwise SB GPIO-s
are not registered at all.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
When storing the UBoot Environment in for example EXT4,
the U-Boot build is broken for several reasons:
1. armada-385-turris-omnia-u-boot.dtsi will not allow
CONFIG_ENV_OFFSET and CONFIG_ENV_SIZE to be undefined
2. armada-37xx/board.c ft_board_setup function does not
exist if CONFIG_ENV_IS_IN_SPI_FLASH is not defined
This commit changes these files so that selecting a
different location for the environment is possible.
Signed-off-by: Rogier Stam <rogier@unrailed.org>
Reviewed-by: Pali Rohár <pali@kernel.org>
In order to sync rk3288.dtsi from Linux it needed to
move all u-boot specific properties in separate dtsi files.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In order to update the DT for rk3288
sync the power domain dt-binding header.
This is the state as of v5.17 in Linux.
Change location to be more in line with other SoCs.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In order to sync rk322x.dtsi from Linux, move all
U-boot specific properties in separate dtsi files.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
MK808 is a RK3066-based board with 1 USB host and 1 USB OTG port,
HDMI and a micro-SD card slot. It also includes on-board NAND
and 1GB of SDRAM. Add rk3066a-mk808.dts. Move U-boot specific
things in a rk3066a-mk808-u-boot.dtsi file.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In the Linux DT the file rk3xxx.dtsi is shared between
rk3066 and rk3188. Add rk3066a.dtsi. Move U-boot specific
things in a rk3066a-u-boot.dtsi file.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Move the include for rk3xxx-u-boot.dtsi to rk3188-u-boot.dtsi
to stay in line with U-boot dtsi files.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The file rk3xxx-u-boot.dtsi was original only for rk3188 and SPL.
With rk3066 added some nodes are also needed in TPL,
so change them to u-boot,dm-pre-reloc
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The GW7903 is based on the i.MX 8M Mini SoC featuring:
- LPDDR4 DRAM
- eMMC FLASH
- microSD socket with voltage select support
- Gateworks System Controller
- M.2 A-E Socket with USB2.0 and PCIe
- MiniPCIe Socket with PCIe, USB2.0, and SIM
- IMX8M FEC
- RS232/RS485/RS422 serial transceiver
- LIS2DE12 3-axis accelerometer
- front panel LED's
- off-board isolated digital I/O
- Wide range DC power input
- 802.3at PoE
- PMIC
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Add new board based on the Toradex Verdin iMX8M Mini SoM, the MX8Menlo.
The board is a compatible replacement for i.MX53 M53Menlo and features
USB, multiple UARTs, ethernet, LEDs, SD and eMMC.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Max Krummenacher <max.krummenacher@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
The Linux kernel moved dt-bindings/pinctrl/pins-imxrt to the device tree
This patch move it in U-Boot as well.
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
In Linux IMX and IMXRT use the device tree to hold the anatop address.
The anatop is used in clock drivers as it controls the internal PLLs
This will move the macro from asm/arch-imxrt to the device tree.
This presumably should also be done with the other IMX boards as well.
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
The GW7902-C revision adds an ADC for the VDD_5P0 voltage rail.
Add register definitions for it.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Add support for Data Modul i.MX8M Mini eDM SBC board. This is an
evaluation board for various custom display units. Currently
supported are serial console, ethernet, eMMC, SD, SPI NOR,
USB host and USB OTG.
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Turns out on certain carrier boards (e.g. Iris V2) and under certain
circumstances (e.g. after a software reset) the SD card may have been
left in a strange state which later failed as follows:
Colibri iMX6ULL # mmc dev 0
Card did not respond to voltage select! : -110
Fix this as follows:
- Re-name the signaling voltage rail regulator from vmmc to vqmmc.
- Fix the name of the GPIO property to gpios.
- Specify 4-bit bus width, no write-protect capability and no 1.8
volt signaling voltage capability.
- Fix the clock vs. command pull-up vs. push-pull configuration.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Now that it is possible to use regulator-fixed-clock make use
of it. This makes U-Boot detect the PHY on first cold-boot.
This commit also adjusts the code in setup_fec and follows
how it is done in mx6ullevk.c
This commit also slows down the boot-process by about 150ms
as it now waits for the regulator-fixed-clock voltage that
drives the PHY to go up.
If you rely on very fast boot-speeds and don't need ethernet
for your boot-process you can safely revert the changes on
imx6ull-colibri.dtsi
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Explicitly use the atf-bl31 type for the bl31.bin atf-blob. This uses
the path from the BL31 environment variable, if defined.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Conversion to DM_SERIAL is mandatory.
Select DM_SERIAL and add a imx6q-tbs2910-u-boot.dtsi file
that describes the nodes that require dm-pre-reloc, which allows
the DM model to configure the UART pinctrl early.
Remove the now unneeded board UART initialization.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Tested-by: Soeren Moch <smoch@web.de>
With DM_SERIAL selected, it is no longer needed board code to
initialize the UART.
Describe the nodes that require dm-pre-reloc, which allows
the DM model to configure the UART pinctrl early.
Remove the now unneeded board UART initialization.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Configure binman ATF blob entry type to use the path from the BL31
environment variable, if defined.
Signed-off-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
The correct compatible string for i.MX8MP variant of DWC EQoS MAC
is "nxp,imx8mp-dwmac-eqos", use it. Drop the two current users of
the current wrong compatible string to avoid breaking them.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
To be in sync with the linux devicetree add the disable-smarteee
property.
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Tested-by: Marek Vasut <marex@denx.de> # 8MNANOD4-EVK
To be in sync with the linux devicetree change the 'phy-reset-gpios' in
the fec node to 'reset-gpios' in the phy node. The PHY reset will be
done by the eth-phy-uclass driver while probing the PHY. This is ok
since it is done before probing the fec.
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Tested-by: Marek Vasut <marex@denx.de> # 8MNANOD4-EVK
Reviewed-by: Fabio Estevam <festevam@gmail.com>
With the correct settings described in the device-tree the PHY settings
in the board init are no longer required. The values are taken from the
linux device tree.
The PHY latency settings are derived from the phy-mode property and the
voltage seetings are done via the regulator.
Suggested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Tested-by: Marek Vasut <marex@denx.de> # 8MNANOD4-EVK
Reviewed-by: Fabio Estevam <festevam@gmail.com>
i.MX8(QM/QXP) - updated device tree for supporting DM in SPL.
disabled use of JR1 in SPL and uboot, as JR1 is reserved
for SECO FW.
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
added crypto node in device tree.
sec is initialized based on job ring information processed
from device tree.
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
MCU Timer0 runs at 250MHz, and the clock-frequency defined in DT appears
incorrect.
Without this delays in R5 SPL are 10x off.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
xilinx:
- Allow booting bigger kernels till 100MB
zynqmp:
- DT updates (reset IDs)
- Remove unneeded low level uart initialization from psu_init*
- Enable PWM features
- Add support for 1EG device
serial_zynq:
- Change fifo behavior in DEBUG mode
zynq_sdhci:
- Fix BASECLK setting calculation
clk_zynqmp:
- Add support for showing video clock
gpio:
- Update slg driver to handle DT flags
net:
- Update ethernet_id code to support also DM_ETH_PHY
- Add support for DM_ETH_PHY in gem driver
- Enable dynamic mode for SGMII config in gem driver
pwm:
- Add driver for cadence PWM
versal:
- Add support for reserved memory
firmware:
- Handle PD enabling for SPL
- Add support for IOUSLCR SGMII configurations
include:
- Sync phy.h with Linux
- Update xilinx power domain dt binding headers
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYkxUZwAKCRDKSWXLKUoM
IXJ2AKCQcoFK7wanCCvZfuEJCSwO5E4eCACginE2CFVXKcY1P8ta4ESusjY2TH0=
=HOoS
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.07-rc1-v2' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2022.07-rc1 v2
xilinx:
- Allow booting bigger kernels till 100MB
zynqmp:
- DT updates (reset IDs)
- Remove unneeded low level uart initialization from psu_init*
- Enable PWM features
- Add support for 1EG device
serial_zynq:
- Change fifo behavior in DEBUG mode
zynq_sdhci:
- Fix BASECLK setting calculation
clk_zynqmp:
- Add support for showing video clock
gpio:
- Update slg driver to handle DT flags
net:
- Update ethernet_id code to support also DM_ETH_PHY
- Add support for DM_ETH_PHY in gem driver
- Enable dynamic mode for SGMII config in gem driver
pwm:
- Add driver for cadence PWM
versal:
- Add support for reserved memory
firmware:
- Handle PD enabling for SPL
- Add support for IOUSLCR SGMII configurations
include:
- Sync phy.h with Linux
- Update xilinx power domain dt binding headers
A big part is the DM pinctrl driver, which allows us to get rid of quite
some custom pinmux code and make the whole port much more robust. Many
thanks to Samuel for that nice contribution! There are some more or less
cosmetic warnings about missing clocks right now, I will send the trivial
fixes for that later.
Another big chunk is the mkimage upgrade, which adds RISC-V and TOC0
(secure images) support. Both features are unused at the moment, but I
have an always-secure board that will use that once the DT lands in the
kernel.
On top of those big things we have some smaller fixes, improving the
I2C DM support, fixing some H6/H616 early clock setup and improving the
eMMC boot partition support.
The gitlab CI completed successfully, including the build test for all
161 sunxi boards. I also boot tested on a A64, A20, H3, H6, and F1C100
board. USB, SD card, eMMC, and Ethernet all work there (where applicable).
Timer0 runs at 200MHz,and the clock-frequency defined in DT is
incorrect. Fix it.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-By: Nishanth Menon <nm@ti.com>
Enable access to ESM0 configuration space and add Main ESM0 and MCU ESM
nodes to the AM64 device tree.
Signed-off-by: Hari Nagalla <hnagalla@ti.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
This syncs the sun8i-h3-nanopi-neo.dts from the Linux tree, from tag
v5.18-rc1.
The alias is required to enable automatic MAC address generation.
Signed-off-by: Baltazár Radics <baltazar.radics@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
U-boot is intended to replace linux kernel in android boot image(ABL), and
it's FIT payload to replace initramfs file. The boot process is similar to
boot image with linux:
- android bootloader (ABL) unpacks android boot image
- ABL sets `linux,initrd-start property` in chosen node in unpacked FDT
- ABL sets x0 register to FDT address, and passes control to u-boot
- u-boot reads x0 register, and stores it in `prevbl_fdt_addr` env variable
- u-boot reads `linux,initrd-start` property,
and stores it in `prevbl_initrd_start_addr`
In this way, u-boot bootcmd relies on `prevbl_initrd_start_addr` env
variable, and boils down to `bootm $prevbl_initrd_start_addr`.
If more control on boot process is desired, pack a boot script in
FIT image, and put it to default configuration
What done:
- strip unneeded config options
- add FIT image support
- add framebuffer node, u-boot logo and video console
- increase LMB_MAX_REGIONS, to store all linux dtb reserved memory regions
- add linux kernel image header
Uart driver causes hang, when u-boot is used in android boot image instead
of linux. Temporary disable console driver, until investigated and fixed.
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmJH28ocHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyDv4B/9FBx95f7zR6WmguG05
VyBchjphsRSuXHb7NieVNNEIpCJu+zw8YutngN2Q8KWIbM9o1OZnrNGxuKR9s+Px
ivMXytGGsIa74XXhxv2boX151R1a5TG4UPf4Vn20qxmUiScE4FaoW5wQHG2vGqxd
/LbzENNCA1A41/RGGysqyY8nQgOEY+Iass+OaHe7XjngcCfY5oY4IRqJ/Ak7ojkv
Vm46i+KCTuyBlcMDjAwDsukSmzsujz2FyzZU1Uy62N8quEdXgrlIA/Yh4oarZ+BO
5W/BJe1rClbnBkMJJn71GUlmnYrioYeUvxvIYwZWooe0Hgr+Iv1vOXv8aJ4hBsdc
yoje
=SwGu
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2022.07-a' of https://source.denx.de/u-boot/custodians/u-boot-at91 into next
First set of u-boot-at91 features for the 2022.07 cycle:
This feature set includes the new driver for the Atmel TCB timer,
alignment in DT for sama7g5 and sama7g5ek board, one Kconfig conversion
for external reset, and the usage of Galois tables from ROM for sama5d2
device.
The ARMv8-R64 architecture introduces optional VMSA (paging based MMU)
support in the EL1/0 translation regime, which makes that part mostly
compatible to ARMv8-A.
Add a new board variant to describe the "BASE-R64" FVP model, which
inherits a lot from the existing v8-A FVP support. One major difference
is that the memory map in "inverted": DRAM starts at 0x0, MMIO is at
2GB [1].
* Create new TARGET_VEXPRESS64_BASER_FVP target, sharing most of the
exising configuration.
* Implement inverted memory map in vexpress_aemv8.h
* Create vexpress_aemv8r defconfig
* Provide an MMU memory map for the BASER_FVP
* Update vexpress64 documentation
At the moment the boot-wrapper is the only supported secure firmware. As
there is no official DT for the board yet, we rely on it being supplied
by the boot-wrapper into U-Boot, so use OF_HAS_PRIOR_STAGE, and go with
a dummy DT for now.
[1] https://developer.arm.com/documentation/100964/1114/Base-Platform/Base---memory/BaseR-Platform-memory-map
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
[Andre: rebase and add Linux kernel header]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[trini: Add MAINTAINERS entry for Peter]
The FVP base model is relying on a DT for Linux operation, so there is
no reason we would need to rely on hardcoded information for U-Boot.
Letting U-Boot use a DT will open up the usage of actual peripherals,
beyond the support for semihosting only.
Enable OF_CONTROL in the Kconfig, and use the latest dts files from
Linux. Depending on whether we use the boot-wrapper or TF-A, there is
already a DTB provided or not, respectively.
To cover the boot-wrapper, we add an arm64 Linux kernel header, which
allows the boot-wrapper to treat U-Boot like a Linux kernel. U-Boot will
find the pointer to the DTB in x0, and will use it.
Even though TF-A carries a DT, at the moment this is not made available
to non-secure world, so to not break users, we use the U-Boot provided
DTB copy in that case. For some reason TF-A puts some DT like structure
at the address x0 is pointing at, but that is very small and doesn't
carry any hardware information. Make the code to ignore those small DTBs.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The Arm Fixed Virtual Platform (FVP) is a software model for an
artificial ARM platform, it is available for free on the Arm website[1].
Add the devicetree files for the latest RevC version, as we will need
them to enable OF_CONTROL for the vexpress_aemv8a_semi board.
This is a verbatim copy of the respective files from Linux v5.17-rc6,
which is unchanged from the v5.16 release.
[1] https://developer.arm.com/tools-and-software/simulation-models/fast-models
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
colibri-imx6ull ethernet device is fec2, while the optional secondary
ethernet is fec1, update the ethernet aliases in the .dts file so that
ethaddr is set to fec2 and eth1addr to fec1.
Without this change the ethernet interfaces have a different
mac address between Linux and U-Boot.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
In order to use the TCB early in boot and in the SPL, add
u-boot,dm-pre-reloc property for the TCB and the clock that is used by
the driver (tcb0_clk).
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
When using interrupts property, a global interrupt controller needs to
be added to avoid warnings when compiling device-tree:
arch/arm/dts/at91-sama5d2_xplained.dtb: Warning (interrupts_property):
/ahb/apb/timer@f800c000: Missing interrupt-parent
Add AIC node as the sama5d2 global interrupt controller.
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Align the DT for sama7g5 SoC and sama7g5 EK board with Linux devicetree
in version 5.18.
Some things remain still different, due to some things yet unimplemented in
certain drivers. These include in PMC, pinctrl, and others.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
In Linux this DT file is named at91-sama7g5ek.dts. Rename it accordingly.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Commit f11513d997 ("net: phy: realtek: Add tx/rx delay config for
8211e") made the Realtek PHY driver honour the phy-mode DT property,
to set up the proper delay scheme for the RX and TX lines. A similar
change in the kernel revealed that those properties were mostly wrong.
The kernel DTs got updated over the last few months, but we were missing
out on the U-Boot version.
Just sync in the phy-mode properties from the mainline kernel,
v5.17-rc7, to avoid the breaking DT sync that late in the cycle.
This fixes Ethernet operation on the affected boards.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Add the PWM node and enable it for AST2600 EVB
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
This patchs add the signal description array for PWM pinctrl settings.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
Commit 0934dddc64 ("arm: a37xx: Update DTS files to version from
upstream Linux kernel") ported Linux's device-tree files for Armada 3720
SOCs. This broke SPI support on some Espressobin boards and results in
following U-Boot error:
Loading Environment from SPIFlash... jedec_spi_nor flash@0: unrecognized JEDEC id bytes: f7, 30, 0b
*** Warning - spi_flash_probe_bus_cs() failed, using default environment
Before that commit DT node for SPI was called 'spi-flash@0' and after
that commit it is called 'flash@0'. Before that commit 'spi-max-frequency'
was set to 50000000 and after it is 104000000.
Rename DT node 'spi-flash@0 in armada-3720-espressobin-u-boot.dtsi to
'flash@0' and set custom U-Boot 'spi-max-frequency' back to 50000000.
With this change SPI is working on Espressobin again and it is detected
with JEDEC ids ef, 60, 16 on our tested unit.
Loading Environment from SPIFlash... SF: Detected w25q32dw with page size 256 Bytes, erase size 4 KiB, total 4 MiB
OK
Note that it is unknown why spi-max-frequency with value 104000000 does not
work in U-Boot as it works fine with Linux kernel. Also note that in
defconfig file configs/mvebu_espressobin-88f3720_defconfig is set option
CONFIG_SF_DEFAULT_SPEED=40000000 which is different value than in DT.
Fixes: 0934dddc64 ("arm: a37xx: Update DTS files to version from upstream Linux kernel")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Commit 0934dddc64 ("arm: a37xx: Update DTS files to version from
upstream Linux kernel") ported Linux's device-tree files for Armada 3720
SOCs. This broke USB port on Turris MOX, because in Linux' DTS the bus
voltage supply is described as a `phy-supply` property of connector
node, a mechanism that is not supported in U-Boot yet.
For now, fix this by adding `vbus-supply` to usb3 node.
Fixes: 0934dddc64 ("arm: a37xx: Update DTS files to version from upstream Linux kernel")
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Add support for Kevin, an RK3399-based convertible chromebook that is
very similar to Bob. This patch is mostly based on existing support for
Bob, with only minor changes for Kevin-specific things.
Unlike other Gru boards, coreboot sets Kevin's center logic to 925 mV,
so adjust it here in the dts as well. The rk3399-gru-kevin devicetree
has an unknown event code reference which has to be defined, set it
to the Linux counterpart. The new defconfig is copied from Bob with the
diffconfig:
DEFAULT_DEVICE_TREE "rk3399-gru-bob" -> "rk3399-gru-kevin"
DEFAULT_FDT_FILE "rockchip/rk3399-gru-bob.dtb" -> "rockchip/rk3399-gru-kevin.dtb"
VIDEO_ROCKCHIP_MAX_XRES 1280 -> 2400
VIDEO_ROCKCHIP_MAX_YRES 800 -> 1600
+TARGET_CHROMEBOOK_KEVIN y
With this Kevin can boot from SPI flash to a usable U-Boot prompt on the
display with the keyboard working, but cannot boot into Linux for
unknown reasons.
eMMC starts in a working state but fails to re-init, microSD card works
but at a lower-than-expected speed, USB works but causes a hang on
de-init. There are known workarounds to solve eMMC and USB issues.
Cc: Marty E. Plummer <hanetzer@startmail.com>
Cc: Simon Glass <sjg@chromium.org>
[Alper: commit message, resync config with Bob, update MAINTAINERS,
add to Rockchip doc, add Kconfig help message, set regulator]
Co-developed-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
This adds some devicetree settings for the Gru-based boards, based on
what works on a Kevin board.
Gru-based boards usually have an 8MiB SPI flash chip and boot from it.
Make the u-boot.rom file intended to be flashed on it match its size.
Add properties for booting from SPI, and only try to boot from SPI as
MMC and SD card don't seem to work in SPL yet.
The Chromium OS EC needs a delay between transactions so it can get
itself ready. Also it currently uses a non-standard way of specifying
the interrupt. Add these so that the EC works reliably.
The Rockchip Embedded DisplayPort driver is looking for a rockchip,panel
property to find the panel it should work on. Add the property for the
Gru-based boards.
The U-Boot GPIO controlled regulator driver only considers the
"enable-gpios" devicetree property, not the singular "enable-gpio" one.
Some devicetree source files have the singular form as they were added
to Linux kernel when it used that form, and imported to U-Boot as is.
Fix one instance of this in the Gru boards' devicetree to the form that
works in U-Boot.
The PWM controlled regulator driver complains that there is no init
voltage set for a regulator it drives, though it's not clear which one.
Set them all to the voltage levels coreboot sets them: 900 mV.
The RK3399 SoC needs to know the voltage level that some supplies
provides, including one fixed 1.8V audio-related regulator. Although
this synchronization is currently statically done in the board init
functions, a not-so-hypothetical driver that does this dynamically would
query the regulator only to get -ENODATA and be confused. Make sure
U-Boot knows this supply is at 1.8V by setting its limits to that.
Most of this is a reapplication of commit 08c85b57a5 ("rockchip: gru:
Add extra device-tree settings") whose changes were removed during a
sync with Linux at commit 167efc2c7a ("arm64: dts: rk3399: Sync
v5.7-rc1 from Linux"). Apply things to rk3399-gru-u-boot.dtsi instead so
they don't get lost again.
Signed-off-by: Simon Glass <sjg@chromium.org>
[Alper: move to -u-boot.dtsi, rewrite commit message, add more nodes]
Co-developed-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
microblaze:
- Add support for reserved memory
xilinx:
- Update FRU code with MAC reading
zynqmp:
- Remove double AMS setting
- DT updates (mostly for SOMs)
- Add support for zcu106 rev 1.0
zynq:
- Update nand binding
nand:
- Aligned zynq_nand to upstream DT binding
net:
- Add support for ethernet-phy-id
mmc:
- Workaround CD in zynq_sdhci driver also for ZynqMP
- Add support for dynamic/run-time SD config for SOMs
gpio:
- Add driver for slg7xl45106
firmware:
- Add support for dynamic SD config
power-domain:
- Update zynqmp driver with the latest firmware
video:
- Add skeleton driver for DP and DPDMA
i2c:
- Fix i2c to work with QEMU
pinctrl:
- Add driver for zynqmp pinctrl driver
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYjIBkgAKCRDKSWXLKUoM
IYUwAKCYRBxb59BFq4MRvTbNcRZ7H4oGIQCfVUl3x9KZ7nFZaYAaBXFBxwna+PE=
=irCR
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.07-rc1' of https://source.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2022.07-rc1
microblaze:
- Add support for reserved memory
xilinx:
- Update FRU code with MAC reading
zynqmp:
- Remove double AMS setting
- DT updates (mostly for SOMs)
- Add support for zcu106 rev 1.0
zynq:
- Update nand binding
nand:
- Aligned zynq_nand to upstream DT binding
net:
- Add support for ethernet-phy-id
mmc:
- Workaround CD in zynq_sdhci driver also for ZynqMP
- Add support for dynamic/run-time SD config for SOMs
gpio:
- Add driver for slg7xl45106
firmware:
- Add support for dynamic SD config
power-domain:
- Update zynqmp driver with the latest firmware
video:
- Add skeleton driver for DP and DPDMA
i2c:
- Fix i2c to work with QEMU
pinctrl:
- Add driver for zynqmp pinctrl driver
Commit 0934dddc64 ("arm: a37xx: Update DTS files to version from
upstream Linux kernel") ported Linux's device-tree files for Armada 3720
SOCs. This broke network on Turris MOX, because the SOC's MDIO bus in
U-Boot currently isn't probed via DM as it's own device, but is
registered as part of mvneta's driver, which means that pinctrl
definitions are not parsed for the MDIO bus node. Also mvneta driver
does not consider "phy-handle" property, only "phy".
For now, fix this by adding armada-3720-turris-mox-u-boot.dtsi file
returning the MDIO to how it was defined previously.
A better solution (using proper mvmdio DM driver) is being work on, but
will need testing on various boards, and we need the bug fixed now for
the upcoming release.
Fixes: 0934dddc64 ("arm: a37xx: Update DTS files to version from upstream Linux kernel")
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
This patch configures U-Boot SPL for DHCOM SoM to permit DFU upload of
SPL and subsequent u-boot.itb for recovery or commissioning purposes.
The DFU usage procedure is identical to STM32MP1 DHCOR SoM, see commit
3919aa1722 ("ARM: dts: stm32: Add DFU support for DHCOR recovery") ,
except for switching the SoM into DFU mode. By default, the DHCOM SoM
has no dedicated mechanism for setting BOOTn straps into UART/USB mode,
therefore to enter DFU mode, the SoC must fail to boot from boot media
which can be selected by the BOOTn strap override mechanism first and
then fall back to DFU mode.
In case of a SoM with pre-populated BOOTn strap override button, power
the system off, remove microSD card (if applicable), hold down the BOOTn
strap override button located between eMMC and SoM edge connector, power
on the SoM. The SoC will fail to boot from SD card and fall back into
DFU mode.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The vdd_io regulator is present only on DHCOR SoM configured for 1V8 IO,
as populated on Avenger96, but not present on 3V3 DHCOR SoM. Move these
extras to Avenger96 u-boot DT extras.
Fixes: 3919aa1722 ("ARM: dts: stm32: Add DFU support for DHCOR recovery")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Fix the following warning in SPL and make sure that even DTs which
enforce Vbus detection using u-boot,force-vbus-detection;, the DFU
in SPL will work.
dwc2-udc-otg usb-otg@49000000: prop pinctrl-0 index 0 invalid phandle
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Device tree alignment with Linux kernel v5.17-rc1
- ARM: dts: stm32: add pull-up to USART3 and UART7 RX pins
on STM32MP15 DKx boards
- ARM: dts: stm32: clean uart4_idle_pins_a node for stm32mp15
- ARM: dts: stm32: tune the HS USB PHYs on stm32mp15xx-dkx
- ARM: dts: stm32: tune the HS USB PHYs on stm32mp157c-ev1
- ARM: dts: stm32: fix stusb1600 pinctrl used on stm32mp157c-dk
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
After double checking some i2c addresses are not correct. It is visible
from i2c dump
ZynqMP> i2c bus
Bus 3: i2c@ff020000
74: i2c-mux@74, offset len 1, flags 0
Bus 5: i2c@ff020000->i2c-mux@74->i2c@0
Bus 6: i2c@ff020000->i2c-mux@74->i2c@2
Bus 7: i2c@ff020000->i2c-mux@74->i2c@1
Bus 8: i2c@ff020000->i2c-mux@74->i2c@3
Bus 4: i2c@ff030000 (active 4)
74: i2c-mux@74, offset len 1, flags 0
Bus 9: i2c@ff030000->i2c-mux@74->i2c@0
Bus 10: i2c@ff030000->i2c-mux@74->i2c@3
Bus 11: i2c@ff030000->i2c-mux@74->i2c@4
Bus 12: i2c@ff030000->i2c-mux@74->i2c@5 (active 12)
51: generic_51, offset len 1, flags 0
60: generic_60, offset len 1, flags 0
74: generic_74, offset len 1, flags 0
Bus 13: i2c@ff030000->i2c-mux@74->i2c@6 (active 13)
51: generic_51, offset len 1, flags 0
5d: generic_5d, offset len 1, flags 0
74: generic_74, offset len 1, flags 0
ZynqMP> i2c dev 4
Setting bus to 4
ZynqMP> i2c mw 74 0 18
ZynqMP> i2c probe
Valid chip addresses: 18 36 37 50 51 60 74
ZynqMP> i2c mw 74 0 20
ZynqMP> i2c probe
Valid chip addresses: 51 60 74
where it is clear that si570 (u5) is at 0x60 address and 8t49n240 (u39) is
also at address 0x60 based on log above.
i2c address 0x74 is i2c mux and 0x51 is eeprom.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/0a198e9d993411e41473d130d5a5c20b6dc83458.1646639616.git.michal.simek@xilinx.com
Remap PCI I/O space to the bus address 0x0 in the Armada 37xx device-tree
in order to support legacy I/O port based cards which have hardcoded I/O
ports in low address space.
Some legacy PCI I/O based cards do not support 32-bit I/O addressing.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This adds platform code and the device tree for the Phytium Pomelo Board.
The initial support comprises the UART and the PCIE.
Signed-off-by: weichangzheng <nicholas_zheng@outlook.com>
Sync the am3517-evm device tree files with those from Linux
5.17-rc5 with some additional fixes for pinmuxing Ethernet and
moving the pinmux references to the respective peripherals.
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Derald D. Woods <woods.technical@gmail.com>
Resync the DTS files for the Logic PD SOM-LV with Linux 5.17-rc5
with some additional pending changes to address issues with
wrong pin-muxing on the OMAP35.
Signed-off-by: Adam Ford <aford173@gmail.com>
This code has been ported from Linux v5.16.9 arch/arm/boot/dts/am33xx.dtsi
file to allow correct usage of MMC2 controller in U-Boot.
This IP block is a bit specific as it is connected to L3 interconnect bus,
whereas mmc[01] are connected to L4.
Proper configuration of this block (including providing clock) is handled
in ti-sysc.c driver.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This change provides similar aliases definitions as now present in
Linux kernel v5.16.9 for am33xx.dtsi file.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Enable the led in the device tree of the refboard bcm96753ref.
It also defines two leds (led_red ad led_green).
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
This add the initial support of the broadcom reference
board bcm96753ref with a bcm6753 SoC.
This board has 1 GB of RAM, 256 MB of flash (nand),
2 USB port, 1 UART, and 4 ethernet ports.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
The main reason is to send pmufw cfg overlay from U-Boot to PMUFW to enable
access to DP. Overlay is sent when cls command is called and for that IP
has to be enabled in carrier cards.
And IP needs to be also enabled in SOM dt because with DTB reselection new
DT is not parsed in pre reloc U-Boot instance. It is called from board_f
via embedded_dtb_select(). That's why bind function is not able to allocate
memory and it ends up with error:
"Video device 'display@fd4a0000' cannot allocate frame buffer memory
-ensure the device is set up before relocation"
To avoid this situation DP is placed also to SOM where bind function is
called and frame buffer memory is allocated and just reused after DTB
reselection. Result is the same. There could be a problem in Linux with
different DP configurations but that's need to be solved there because
console should be on from u-boot already.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/c4f31641f917fddb09d976f56875057c658f264c.1645629459.git.michal.simek@xilinx.com
Use ethernet-phy-id compatible string to properly describe phy reset on
kv260 boards. Previous description wasn't correct because reset was done
for mdio bus to operate and it was in this case used for different purpose
which was eth phy reset. With ethernet-phy-id phy reset happens only for
the phy via phy framework.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/73b64f1a2b873b4e26bd2b365364bdf313794ae2.1645629459.git.michal.simek@xilinx.com
With limited low level configuration done via psu-init only IPs connected
on SOM are initialized and configured. All IPs connected to carrier card
are not initialized. There is a need to do proper reset, pin configuration
and also clock setting.
The patch targets the last part which is setting up proper clock for USBs
and SDs.
Also setup proper bus width for SD cards.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Sai Krishna Potthuri <lakshmi.sai.krishna.potthuri@xilinx.com>
Link: https://lore.kernel.org/r/d9f80b2551bd246c3d7ecb09b516806c8dc83ed9.1645629459.git.michal.simek@xilinx.com
Recent unrelated fixes (9876ae7db6) revealed that we were missing bits
from 2af181b53e in the IOT2050 dt. Add them, but only for main U-Boot.
SPL loads from QSPI only, thus cannot use DMA.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmIgkpAcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyDmXCACMc7jIpdFEz2NKTnSy
hudLhzWTQ8NrPFrOkxAJREMaMhRCh5b/5AW0469fFFZ86NxpgHyuoNJtnflN/V8t
ucVfM3/fJgfoyBnfyzv+Cuju8DQNGZZnBrYKBeIKzlD8/nwX0Ah/xbGb/IKCD3cT
IVl8UqXh57NDVYApb/04sDK1hNfjex3jYejH/l8pQYiF/fsfYQI9XPGdD0w4N6N1
D1Rtpmr9lJqJiq7xjCIwHoqigYV4E7lu5P4Uk9RzxBOo8BAcrn10DMgjlg9AL4F/
LqmLCTC65myV5tqrdVES6EHke7S3QD9vi6qB4qB/tr/AE3c/4cdzGUL7nkyzI1Cq
iZlg
=9HIi
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-fixes-2022.04-a' of https://source.denx.de/u-boot/custodians/u-boot-at91
First set of u-boot-atmel fixes for the 2022.04 cycle:
This fixes set includes only a single fix for the Ethernet on sama7g5ek
board which is broken at the moment.
Simplify the binman config and fdt nodes by using the "@..-SEQ"
substitutions and CONFIG_OF_LIST.
Signed-off-by: Michael Walle <michael@walle.cc>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
The default U-Boot environment variables and design are all set up for
the MAIN R5FSS cluster to be in Split-mode. This is the setting used
when the dts nodes were originally added in v2021.01 U-Boot and the
dt nodes are synched with the kernel binding property names in
commit 468ec2f3ef ("remoteproc: k3_r5: Sync to upstreamed kernel DT
property names") merged in v2021.04-rc2.
The modes for the MAIN R5FSS cluster got switched back to LockStep mode
by mistake in commit fa09b12dc5 ("arm: ti: k3: Resync dts files and
bindings with Linux Kernel v5.14") in v2022.01-rc1. This throws the
following warning messages when early-booting the cores using default
env variables,
k3_r5f_rproc r5f@5d00000: Invalid op: Trying to start secondary core 7 in lockstep mode
Load Remote Processor 3 with data@addr=0x82000000 83148 bytes: Failed!
Fix this by switching back both the clusters to the expected Split-mode.
Make this mode change in the u-boot specific dtsi file to avoid such
sync overrides in the future until the kernel dts is also switched to
Split-mode by default.
Fixes: fa09b12dc5 ("arm: ti: k3: Resync dts files and bindings with Linux Kernel v5.14")
Signed-off-by: Suman Anna <s-anna@ti.com>
Correct the min/max voltages of VDD_CPU. As per data sheet the VDD_CPU
minimum voltage is .6V & maximum voltage is .9V.
Correct the same. While at it fix the comment to reflect VDD_CPU
instead of VDD_MPU.
Data Sheet Link: https://www.ti.com/lit/gpn/dra829v
Signed-off-by: Keerthy <j-keerthy@ti.com>
Add support for ethernet on the imx8mn-ddr4-evk.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
The GW7902 is based on the i.MX 8M Mini / Nano SoC featuring:
- LPDDR4 DRAM
- eMMC FLASH
- Gateworks System Controller
- LTE CAT M1 modem
- USB 2.0 HUB
- M.2 Socket with USB2.0, PCIe, and dual-SIM
- IMX8M FEC
- PCIe based GbE
- RS232/RS485/RS422 serial transceiver
- GPS
- CAN bus
- WiFi / Bluetooth
- MIPI header (DSI/CSI/GPIO/PWM/I2S)
- PMIC
To add support for the i.MX8M Nano GW7902:
- Add imx8mn-venice dts/defconfig/include
- Add imx8mn-gw7902 dts
- Add imx8mn-2gb lpddr4 dram configs
- Add misc support for IMX8M Nano SoC
- rename imx8mm-venice.c to venice.c as it is no longer imx8mm specific
- update README with differences for IMX8MN vs IMX8MM
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
- a37xx: pci: Cleanup and minor fix for root port check (Pali)
- pci: mvebu: Ensure that root port is always on root zero bus (Pali)
- kwbimage: Fix dumping DATA registers for v0 images (Pali)
- kwbimage: Support for parsing extended v0 format (Pali)
- a37xx: Fix code and update DTS files to upstream version (Pali)
- a37xx: Fix and extend building memory map (Pali)
- ddr: marvell: a38x: fix BYTE_HOMOGENEOUS_SPLIT_OUT decision (Marek)
- mvebu: Optionally reset board on DDR training failure (Marek)
This change updates all Armada 37xx DTS files to version which is used by
Linux kernel v5.18.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Official DT bindings for Espressobin have disabled eMMC node.
As U-Boot requires to have this node enabled by default, do it in
armada-3720-espressobin-u-boot.dtsi DTS file.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
U-Boot specific changes should be in armada-3720-espressobin-u-boot.dtsi DTS file.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
In Linux kernel version of armada-37xx.dtsi file sdhci1 pointer refers to
sdhci@d0000 node and sdhci0 pointer to sdhci@d8000 node.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Official DT bindings have only one reg property: watchdog address space.
Convert armada-37xx-wdt.c driver to offical DT bindings and access sel_reg
register via MVEBU_REGISTER() macro, as its value (required by U-Boot
driver) is not in DT yet. In later stage can be driver cleaned to not use
it.
This change would allow U-Boot to use A3720 watchdog DTS structure from
Linux kernel.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Official DT bindings use compatible string marvell,armada-3700-ehci.
Update drivers and DTS files.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
In commit d368e10705 ("phy: marvell: a3700: Convert to official DT
bindings in COMPHY driver") was done update to official DT bindings but
compatible string of official DT bindings was not updated.
Fix it now.
Fixes: d368e10705 ("phy: marvell: a3700: Convert to official DT bindings in COMPHY driver")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
A new lpddr4 configuration is introduced for J7 SK with 4266 MTs data
rate. Therefore, update the R5 DTS file to point to the new DDR config
file.
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
EMIF tool for J721E SK is now updated to 0.6.1 that includes
* Updated write DQ training pattern to enable user pattern and clock
pattern (from 0x7 to 0x6).
* Updated IO drive strength to 40-80-80 Ohms.
J721E SK uses the lpddr4 configuration of 4266 MTs data rate which is
the same as J721E EVM but facing random failures. As the tool update is
specific to the SK board, add a new lpddr4 config of 4266 MTs.
Signed-off-by: Kevin Scholz <k-scholz@ti.com>
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
J721E Starter Kit (SK)[1] is a low cost, small form factor board designed
for TI’s J721E SoC. TI’s J721E SoC comprises of dual core A72, high
performance vision accelerators, video codec accelerators, latest C71x
and C66x DSP, high bandwidth real-time IPs for capture and display, GPU,
dedicated safety island and security accelerators. The SoC is power
optimized to provide best in class performance for industrial and
automotive applications.
J721E SK supports the following interfaces:
* 4 GB LPDDR4 RAM
* x1 Gigabit Ethernet interface
* x1 USB 3.0 Type-C port
* x3 USB 3.0 Type-A ports
* x1 PCIe M.2 E Key
* x1 PCIe M.2 M Key
* 512 Mbit OSPI flash
* x2 CSI2 Camera interface (RPi and TI Camera connector)
* 40-pin Raspberry Pi GPIO header
Add A72 specific dts for J721E-SK.
[1] https://www.ti.com/tool/SK-TDA4VM
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Board ID I2C EEPROM will be probed before SYSFW is available.
So drop the power-domains property for wakup_i2c0 on which
board ID EEPROM is connected.
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
The changes introduced with commit 6337d53fdf ("arm: dts: sync am33xx
with Linux 5.9-rc7") prevent the PDU001 from operating correctly.
This patch fixes the configuration of the pin multiplexer and uart3.
Signed-off-by: Felix Brack <fb@ltec.ch>
EMIF tool for AM64 SK is now updated to 0.8.0 that includes
* disabled Write DQ training
* improve CA ODT to 60 ohms
The lpddr4 enabled with periodic WDQ training is causing periodic 26us
stall. This makes the SoC stall without doing anything which leads to
R5 interrupt latency in TCM memory. Due to this periodic training there
are some outstanding CPU transactions waiting for the lpddr4 to complete.
Hence, disable the periodic write DQ training during the
non-initialization stage of lpddr4 which results in an approximate 1us
stall. Also, update the lpddr4 config to improve CA ODT by 60 ohms
The rationales are as follows:
- PI_WDQLVL_EN: 2 Bits register field to support write DQ leveling,
disable bit 1 that supports Write DQ during non-initialization to
avoid ~26us stall during code execution.
- MR11_DATA_F1/F2_x register fields value changed to 0x66 that changes
the CA ODT from 48ohm to 60ohm to improve the eye margin on CA bus by
increasing the signal swing.
Signed-off-by: James Doublesin <doublesin@ti.com>
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
When building for a custom board, it is quite common to maintain a
private branch which include some defconfig and .dts files. But to
hook up those .dts files requires modifying a file "belonging" to
upstream U-Boot, the arch/*/dts/Makefile. Forward-porting that branch
to a newer upstream then often results in a conflict which, while it
is trivial to resolve by hand, makes it harder to have a CI do "try to
build our board against latest upstream".
The .config usually includes information on precisely what .dtb(s) are
needed, so to avoid having to modify the Makefile, simply add the
files in (SPL_)OF_LIST to dtb-y.
A technicality is that (SPL_)OF_LIST is not always defined, so rework
the Kconfig symbols so that (SPL_)OF_LIST is always defined (when
(SPL_)OF_CONTROL), but only prompted for in the cases which used to be
their "depends on".
nios2 and microblaze already have something like this in their
dts/Makefile, and the rationale in commit 41f59f6853 is similar to
the above. So this simply generalizes existing practice. Followup
patches could remove the logic in those two makefiles, just as there's
potential for moving some common boilerplate from all the
arch/*/dts/Makefile files to the new scripts/Makefile.dts.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Simon Glass <sjg@chromium.org>
The PLL_CMNLC clocks are modelled as a child clock device of seirra. In the
function device_probe, the corresponding clocks are probed before calling
the device's probe. The PLL_CMNLC mux clock can only be created after the
device's probe. Therefore, move assigned-clocks and assigned-clock-parents
to the link nodes in U-Boot device tree file.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
