Commit graph

16238 commits

Author SHA1 Message Date
Lothar Waßmann
267c5b7989 arm: mx6: remove unused config variable CONFIG_SPL_NAND_MXS
The config variable CONFIG_SPL_NAND_MXS is only set in
include/configs/imx6_spl.h but used nowhere.
Remove it.

Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2017-05-31 10:11:11 +02:00
Tim Harvey
6ecbe13756 drivers: pci: imx: add imx_pcie_remove function
There is no dedicated reset signal wired up for the MX6QDL thus if the
bootloader enables the link we need some special handling to get the core
back into a state where it is safe to touch it for configuration.

While there has been some special handling in the Linux kernel to do this,
it was removed in 4.11 thus we need to do it properly in the bootloader
and therefore without this if you enable PCI in the bootloader you will hang
while booting the 4.11 kernel.

This puts the PCIe controller back into a safe state for the kernel driver
before launching the kernel.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Peter Senna Tschudin <peter.senna@collabora.com>
2017-05-31 10:09:03 +02:00
Fabio Estevam
da384fc67a mx7dsabresd: Increase CONFIG_ENV_OFFSET
After running 'saveenv' we can no longer boot.

Adjust CONFIG_ENV_OFFSET so that U-Boot binary and the environment
section do not overlap.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-05-31 10:04:59 +02:00
Vanessa Maegima
1541d7a63d pico-imx7d: Add initial support
Add the initial support for pico-imx7d board based on Wig Cheng's
source code.

Add support for eMMC, USB gadget, I2C, PMIC and Ethernet.

For more information about this board, please visit:
http://www.technexion.org/products/pico/pico-som/pico-imx7-emmc

Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-05-31 09:58:40 +02:00
Patrick Wildt
f3d9ec2a69 arm: mvebu: clearfog: generic distro bootcmd
Switch Clearfog to the generic distro defaults.  This has been taken
from a Debian mailing list thread:

https://lists.debian.org/debian-boot/2016/10/msg00026.html

Signed-off-by: Patrick Wildt <patrick@blueri.se>
Signed-off-by: Stefan Roese <sr@denx.de>
2017-05-31 07:42:52 +02:00
Keerthy
6183b29559 power: pmic: tps65218: Fix tps65218_voltage_update function
Currently while setting the vsel value for dcdc1 and dcdc2
the driver is wrongly masking the entire 8 bits in the process
clearing PFM (bit7) field as well. Hence describe an appropriate
mask for vsel field and modify only those bits in the vsel
mask.

Source: http://www.ti.com/lit/ds/symlink/tps65218.pdf

Signed-off-by: Keerthy <j-keerthy@ti.com>
Fixes: 86db550b38 ("power: Add support for the TPS65218 PMIC")
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2017-05-29 17:28:52 +09:00
Tom Rini
7ca0d3dde1 mmc: Change 'part_config' to be a u8 not char.
In some places we check if part_config is set to MMCPART_NOAVAILABLE
(0xff).  With part_config being a char this is always false.  We should
be using a u8 to store this value instead, after a quick consultation
with the Linux Kernel.  Reported by clang-3.8.

Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-05-29 17:28:51 +09:00
Tom Rini
380e86f361 Merge git://git.denx.de/u-boot-fsl-qoriq 2017-05-26 11:19:27 -04:00
Tom Rini
8dc1b17f14 Merge branch 'master' of git://git.denx.de/u-boot-nds32
Move FTMAC100 to where it should be, alphabetically in
drivers/net/Kconfig

Signed-off-by: Tom Rini <trini@konsulko.com>

Conflicts:
	drivers/net/Kconfig
2017-05-26 11:18:53 -04:00
Tom Rini
be62fbf376 Merge branch 'rmobile' of git://git.denx.de/u-boot-sh 2017-05-23 16:22:03 -04:00
Udit Agarwal
7676074ac7 armv8: LS2080A: Adjust memory map for secure boot headers for NOR-boot
This patch adjusts memory map for secure boot headers on LS2080AQDS
and LS2080ARDB platforms. Secure boot headers are placed on NOR
flash at offset 0x00600000.

Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-05-23 09:59:14 -07:00
Santan Kumar
f5bf23d827 armv8: ls2080ardb, ls2080aqds: Adjust memory map for NOR-boot
This patch adjusts memory map for images on LS2080ARDB and
LS2080AQDS NOR flash as below

Image				Flash Offset
RCW+PBI				0x00000000
Boot firmware (U-Boot)		0x00100000
Boot firmware Environment	0x00300000
PPA firmware			0x00400000
PHY firmware			0x00980000
DPAA2 MC			0x00A00000
DPAA2 DPL			0x00D00000
DPAA2 DPC			0x00E00000
Kernel.itb			0x01000000

Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-05-23 09:52:29 -07:00
Alison Wang
8104deb2d6 armv8: layerscape: Adjust memory mapping for Flash/SD card on LS1046A
This patch is to adjust the memory mapping for FLash/SD card on
LS1046AQDS and LS1046ARDB, such as FMAN firmware load address, U-Boot
start address on serial flash and environment address.

Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-05-23 09:51:28 -07:00
Alison Wang
a9a5cef391 armv8: layerscape: Adjust memory mapping for Flash/SD card on LS1043A
This patch is to adjust the memory mapping for FLash/SD card on
LS1043AQDS and LS1043ARDB, such as PPA firmware load address, FMAN
firmware load address, QE firmware load address, U-Boot start address
on serial flash and environment address.

Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-05-23 09:50:25 -07:00
Alison Wang
615bfce564 arm: ls1021a: Adjust memory mapping for Flash/SD card on LS1021AQDS/TWR
This patch is to adjust the memory mapping for FLash/SD card on
LS1021AQDS and LS1021ATWR, such as U-Boot start address on serial
Flash, QE firmware load address and environment address.

Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-05-23 09:48:41 -07:00
Priyanka Jain
3049a583f3 armv8: ls2080ardb: Add LS2081ARDB board support
LS2081ARDB board is similar to LS2080ARDB board with few differences
 It hosts LS2081A SoC
 Default boot source is QSPI-boot
 It does not have IFC interface
 RTC and QSPI flash device are different
 It provides QIXIS access via I2C

Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-05-23 09:47:08 -07:00
Priyanka Jain
89a168f776 armv8: ls2080ardb: Add QSPI-boot support
QSPI-boot is supported on LS2088ARDB RevF board with LS2088A SoC.
LS2088ARDB RevF Board has limitation that QIXIS can not be accessed.
CONFIG_FSL_QIXIS is not enabled.

Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-05-23 09:38:55 -07:00
York Sun
c40e6f9169 armv8: ls1043ardb: Make NET independent of FMan
This allows using PCIe NIC without enabling DPAA FMan.

Signed-off-by: York Sun <york.sun@nxp.com>
CC: Mingkai Hu <mingkai.hu@nxp.com>
Acked-by: Mingkai Hu <mingkai.hu@nxp.com>
2017-05-23 09:24:43 -07:00
York Sun
99b47c25d0 armv8: ls1046ardb: Make NET independent of FMan
This allows using PCIe NIC without enabling DPAA FMan.

Signed-off-by: York Sun <york.sun@nxp.com>
CC: Mingkai Hu <mingkai.hu@nxp.com>
Acked-by: Mingkai Hu <mingkai.hu@nxp.com>
2017-05-23 09:23:52 -07:00
Suresh Gupta
5e3f763a4b armv8: ls1012a: fix the size of flash for multiple boards
LS1012AFRDM, LS1012ARDB, LS1012AQDS all have S25FS512S flash
of 64MB size.

Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
2017-05-23 09:18:01 -07:00
Suresh Gupta
e9420444f6 armv8: layperscape: remove CONFIG_SPI_FLASH_BAR from some platforms
ls1012ardb, ls1046ardb, ls2080ardb have S25FS512S flash which does
not support Bank Address Register commands.

Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-05-23 09:12:42 -07:00
Hou Zhiqiang
3098e539d6 armv8: ls1046a: enable PCI command tool
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-05-23 09:12:00 -07:00
rick
be71a179bd nds32: eth: Support ftmac100 DM.
Support Andestech eth ftmac100 device tree flow on AG101P/AE3XX platform.
Verification:
 Boot linux kernel via dhcp and bootm ok.

 NDS32 # setenv bootm_size 0x2000000;setenv fdt_high 0x1f00000;
 NDS32 # dhcp 0x600000 10.0.4.97:boomimage-310y-ae300-spi.bin
 BOOTP broadcast 1
 BOOTP broadcast 2
 BOOTP broadcast 3
 BOOTP broadcast 4
 DHCP client bound to address 10.0.4.178 (4899 ms)
	Using mac@e0100000 device
	TFTP from server 10.0.4.97; our IP address is 10.0.4.178
	Filename 'boomimage-310y-ae300-spi.bin'.
	Load address: 0x600000
	Loading: #################################################################
	         #################################################################
	         #################################################################
...
...
	         ###################################
	         233.4 KiB/s
					 done
					 Bytes transferred = 13872076 (d3abcc hex)
	NDS32 # dhcp 0x2000000 10.0.4.97:ae300.dtb
	BOOTP broadcast 1
	BOOTP broadcast 2
	BOOTP broadcast 3
	BOOTP broadcast 4
	DHCP client bound to address 10.0.4.178 (4592 ms)
	Using mac@e0100000 device
	TFTP from server 10.0.4.97; our IP address is 10.0.4.178
	Filename 'ae300.dtb'.
	Load address: 0x2000000
	Loading: #
	         82 KiB/s
					 done
					 Bytes transferred = 2378 (94a hex)
	NDS32 # bootm 0x600000 - 0x2000000
	 Image Name:
	 Created:      2017-03-22   6:52:03 UTC
	 Image Type:   NDS32 Linux Kernel Image (uncompressed)
	 Data Size:    13872012 Bytes = 13.2 MiB
	 Load Address: 0000c000
	 Entry Point:  0000c000
	 Verifying Checksum ... OK
	 Booting using the fdt blob at 0x2000000
	 Loading Kernel Image ... OK
	 Loading Device Tree to 01efc000, end 01eff949 ... OK
	 Linux version 3.10.102-20375-gb0034c1-dirty (rick@app09)
	(gcc version 4.9.3 (2016-07-06_nds32le-linux-glibc-v3_experimental) )
  #293 PREEMPT Wed Mar 22 14:49:28 CST 2017
	CPU: NDS32 N13, AndesCore ID(wb), CPU_VER 0x0d11103f(id 13, rev 17, cfg 4159)
...
...
Signed-off-by: rick <rick@andestech.com>
2017-05-23 13:48:27 +08:00
Tom Rini
711391131c Merge git://git.denx.de/u-boot-sunxi
trini: Make Kconfig SPL_xxx entires only show if SPL, so that we don't
get Kconfig errors on platforms without SPL, ie sandbox (without SPL).

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-05-22 19:20:28 +00:00
Tom Rini
c2774e6149 Merge branch 'master' of git://git.denx.de/u-boot-nds32 2017-05-22 14:14:44 -04:00
Lothar Waßmann
e34b913a94 ColdFire: Remove rogue 'CONFIG_SYS_NO_FLASH' embedded within another CONFIG_ name
The original commit for the MCF54418TWR ColdFire development board
support defined a 'CONFIG_SYS_FAULT_ECCONFIG_SYS_NO_FLASHHO_LINK_DOWN'
which obviously has a rogue 'CONFIG_SYS_NO_FLASH' embedded in the
intended 'CONFIG_SYS_FAULT_ECHO_LINK_DOWN' define.

Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
2017-05-22 12:45:33 -04:00
Simon Glass
ee7c0e712a Convert CONFIG_CMD_LZMADEC to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_LZMADEC

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-05-22 12:45:33 -04:00
Simon Glass
aed998aa34 Convert CONFIG_LZMA to Kconfig
This converts the following to Kconfig:
   CONFIG_LZMA

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-05-22 12:45:32 -04:00
Simon Glass
4a37cb5038 Kconfig: Drop CONFIG_CMD_LOADY
This is not used in U-Boot. Drop it.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-05-22 12:45:32 -04:00
Simon Glass
6bac227a67 Convert CONFIG_CMD_KGDB to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_KGDB

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-05-22 12:45:32 -04:00
Simon Glass
1b330894bd Convert CONFIG_CMD_IRQ to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_IRQ

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-05-22 12:45:31 -04:00
Simon Glass
b8682a7fcf Convert CONFIG_CMD_JFFS2 to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_JFFS2

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-05-22 12:45:30 -04:00
Simon Glass
7d0f5c1300 Convert CONFIG_CMD_IOTRACE to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_IOTRACE

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-05-22 12:45:30 -04:00
Simon Glass
070f3168fa Convert CONFIG_CMD_IOLOOP to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_IOLOOP

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-05-22 12:45:29 -04:00
Simon Glass
594e8d1c62 Convert CONFIG_CMD_IO to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_IO

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-05-22 12:45:29 -04:00
Simon Glass
56aa7dcbdb Kconfig: Drop CONFIG_CMD_IMX_FUSE
This option is not used in U-Boot. Drop it.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-05-22 12:45:29 -04:00
Simon Glass
b5834adfed Kconfig: Drop CONFIG_CMD_IMXOTP
This option is not used in U-Boot. Drop it.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-05-22 12:45:28 -04:00
Simon Glass
c7c111e5f7 Convert CONFIG_CMD_IMMAP to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_IMMAP

Also move this command out of the cmd/ directory since it is
PowerPC-specific.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-05-22 12:45:28 -04:00
Simon Glass
fc843a02ac Kconfig: Add a CONFIG_IDE option
At present IDE support is controlled by CONFIG_CMD_IDE. Add a separate
CONFIG_IDE option so that IDE support can be enabled without requiring
the 'ide' command.

Update existing users and move the ide driver into drivers/block since
it should not be in common/.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-05-22 12:45:27 -04:00
Simon Glass
75eb9976b7 Convert CONFIG_CMD_IDE to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_IDE

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-05-22 12:45:27 -04:00
Simon Glass
7a01f3c6f4 Convert CONFIG_CMD_HDMIDETECT to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_HDMIDETECT

Note that we cannot do 'default y if VIDEO' because this option is only
enabled for a small subset of mx6 boards. Also this command is is not a
great implementation (it doesn't use driver model).

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-05-22 12:45:22 -04:00
Simon Glass
e8e09ba5b7 Convert CONFIG_CMD_HD44760 to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_HD44760

Also drop CONFIG_CMD_HD44780 which appears to be a typo.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-05-22 12:38:23 -04:00
Simon Glass
551c393446 Convert CONFIG_CMD_HASH to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_HASH

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Rework slightly, enable on some boards again]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-05-22 12:38:15 -04:00
Simon Glass
520f556d0d Convert CONFIG_CMD_GSC to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_GSC

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-05-22 09:33:58 -04:00
Simon Glass
d91a9d7fb3 Convert CONFIG_CMD_GETTIME to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_GETTIME

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-05-22 09:33:58 -04:00
Simon Glass
51f2937036 Convert CONFIG_CMD_FUSE to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_FUSE

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-05-22 09:33:58 -04:00
Simon Glass
fe7604a3bc Convert CONFIG_CMD_FPGA_LOADBP et al to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_FPGA_LOADBP
   CONFIG_CMD_FPGA_LOADFS
   CONFIG_CMD_FPGA_LOADMK
   CONFIG_CMD_FPGA_LOADP

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-05-22 09:33:57 -04:00
Simon Glass
df1c489ade Convert CONFIG_CMD_FPGAD to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_FPGAD

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-05-22 09:33:57 -04:00
Simon Glass
b0e7a70a05 Convert CONFIG_CMD_FDC to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_FDC

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-05-22 09:33:56 -04:00
Simon Glass
ef072200fa Convert CONFIG_CMD_ETHSW to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_ETHSW

Also enable it for sandbox to increase build coverage.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-05-22 09:33:56 -04:00
Simon Glass
230ecd7150 Convert CONFIG_CMD_ERRATA to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_ERRATA

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-05-22 09:33:54 -04:00
Simon Glass
ffc76589d0 Convert CONFIG_CMD_ENV_FLAGS to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_ENV_FLAGS

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-05-22 09:33:54 -04:00
Simon Glass
a55d29d2ac Convert CONFIG_CMD_ENV_CALLBACK to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_ENV_CALLBACK

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-05-22 09:33:53 -04:00
Simon Glass
dcab138793 Kconfig: Drop CONFIG_CMD_ENV
This option is not used in U-Boot. Drop it.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-05-22 09:33:53 -04:00
Simon Glass
42e6f852dd Convert CONFIG_CMD_ENTERRCM to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_ENTERRCM

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-05-22 09:33:53 -04:00
Simon Glass
a1dc980d88 Convert CONFIG_CMD_EEPROM et al to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_EEPROM
   CONFIG_CMD_EEPROM_LAYOUT
   CONFIG_EEPROM_LAYOUT_HELP_STRING

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Rework Kconfig logic slightly, define EEPROM location on TI eval
platforms]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-05-22 09:33:49 -04:00
Simon Glass
d96e8985f6 Convert CONFIG_CMD_EECONFIG to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_EECONFIG

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-05-22 08:37:14 -04:00
Simon Glass
d63323fb59 Convert CONFIG_CMD_ECCTEST to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_ECCTEST

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-05-22 08:37:13 -04:00
Simon Glass
21c7297991 Kconfig: Drop CONFIG_SYS_I2C_DS4510_ADDR
This is only used by one board and always set to 0x51. Drop this option.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
2017-05-22 08:37:12 -04:00
Simon Glass
dd937b82fe Kconfig: Drop CONFIG_SYS_I2C_DS1621_ADDR
Now that dtt is gone, this is not used. Drop it.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-05-22 08:37:12 -04:00
Simon Glass
853eaa4f30 Drop digital thermometer and thermostat (DTT) drivers
This subsystem is quite old. It has been replaced with a driver-model
version (UCLASS_THERMAL). Boards are free to convert to that if required,
but here is a removal patch that could be applied in the meantime.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-05-22 08:37:11 -04:00
Simon Glass
ab3c4fbe8a Drop three-wire serial (TWS) support
This subsystem has not been converted to driver model, there is only one
driver and only one board that uses it. Drop it and its CONFIG option.

Also drop the rtc4543 RTC driver since it uses TWS.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-05-22 08:37:10 -04:00
Simon Glass
2c6ebff1e1 Kconfig: Drop CONFIG_SYS_I2C_DTT_ADDR
This option is only defined to a non-default value by canyonlands, which
needs conversion to driver model (where the I2C address would be defined
by the device tree).

Drop this option.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
2017-05-22 08:37:09 -04:00
Simon Glass
879704d8f7 Convert CONFIG_DS4510 to Kconfig
This converts the following to Kconfig:
   CONFIG_DS4510

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
2017-05-22 08:37:08 -04:00
Simon Glass
1136eb5e8f Kconfig: Drop CONFIG_CMD_DS4510
This option enables a command in the driver. But the functions defined by
the driver are not called anywhere else in U-Boot. So it does not seem
useful to have this driver without its commands.

Drop this option, move the header file out of the common include/
directory and make all the function static.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
2017-05-22 08:37:07 -04:00
Simon Glass
523f97ac75 Kconfig: Drop CONFIG_CMD_DS4510_INFO
This option is only used in one driver and two boards. It does not seem
worth having the ability to remove this part of the support.

Drop the option.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
2017-05-22 08:37:05 -04:00
Tom Rini
089df18bfe lib: move hash CONFIG options to Kconfig
Commit 94e3c8c4fd ("crypto/fsl - Add progressive hashing support
using hardware acceleration.") created entries for CONFIG_SHA1,
CONFIG_SHA256, CONFIG_SHA_HW_ACCEL, and CONFIG_SHA_PROG_HW_ACCEL.
However, no defconfig has migrated to it.  Complete the move by first
adding additional logic to various Kconfig files to select this when
required and then use the moveconfig tool.  In many cases we can select
these because they are required to implement other drivers.  We also
correct how we include the various hashing algorithms in SPL.

This commit was generated as follows (after Kconfig additions):

[1] tools/moveconfig.py -y SHA1 SHA256 SHA_HW_ACCEL
[2] tools/moveconfig.py -y SHA_PROG_HW_ACCEL

Note:
We cannot move SHA_HW_ACCEL and SHA_PROG_HW_ACCEL simultaneously
because there is dependency between them.

Cc: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Cc: Naveen Burmi <NaveenBurmi@freescale.com>
Cc: Po Liu <po.liu@freescale.com>
Cc: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Cc: Priyanka Jain <Priyanka.Jain@freescale.com>
Cc: Shaohui Xie <Shaohui.Xie@freescale.com>
Cc: Chunhe Lan <Chunhe.Lan@freescale.com>
Cc: Chander Kashyap <k.chander@samsung.com>
Cc: Steve Rae <steve.rae@raedomain.com>
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: Feng Li <feng.li_2@nxp.com>
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Sumit Garg <sumit.garg@nxp.com>
Cc: Mingkai Hu <Mingkai.Hu@freescale.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Akshay Saraswat <akshay.s@samsung.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-05-22 08:36:58 -04:00
Tom Rini
0db7f6859f FIT: Rename FIT_DISABLE_SHA256 to FIT_ENABLE_SHA256_SUPPORT
We rename CONFIG_FIT_DISABLE_SHA256 to CONFIG_FIT_ENABLE_SHA256_SUPPORT which
is enabled by default and now a positive option.  Convert the handful of boards
that were disabling it before to save space.

Cc: Dirk Eibach <eibach@gdsys.de>
Cc: Lukasz Dalek <luk0104@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-22 07:29:55 -04:00
Ley Foon Tan
0680f1b1f7 Convert CONFIG_SPL_BOARD_INIT to Kconfig
This converts the following to Kconfig:
   CONFIG_SPL_BOARD_INIT

Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
[trini: Update the Kconfig logic]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-05-22 07:29:48 -04:00
rick
b841b6e946 nds32: Support AE3XX platform.
Support Andestech AE3xx platform: serial, timer device tree flow.

Signed-off-by: rick <rick@andestech.com>
2017-05-22 14:05:46 +08:00
rick
86132af799 nds32: Support AG101P serial DM.
Support AG101P serial device tree flow.

Signed-off-by: rick <rick@andestech.com>
2017-05-22 14:05:33 +08:00
Marek Vasut
4c443bdbf6 ARM: rmobile: salvator-x: Enable SCIF2 clock
There are two UARTs on the board, so enable the clock for the
second one as well.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-05-22 04:38:27 +09:00
Marek Vasut
d1018f5f9f ARM: rmobile: salvator-x: Add USB support
Add support for the EHCI USB.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-05-22 04:38:27 +09:00
Marek Vasut
fe2e8ff955 ARM: rmobile: salvator-x: Add DVFS and PMIC support
Add support for rebooting the board using the ROHM BD9571MWV I2C PMIC,
but keep the CPU reboot option as a fallback.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-05-22 04:38:27 +09:00
Marek Vasut
90e53f8b45 ARM: rmobile: salvator-x: Add RAVB ethernet support
Add support for the AVB ethernet on the Salvator-X board.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-05-22 04:38:27 +09:00
Marek Vasut
50fb0c451f ARM: rmobile: salvator-x: Add SD support
Add support for the SD card slots on the Salvator-X board.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-05-22 04:38:27 +09:00
Marek Vasut
8474681c3e ARM: rmobile: salvator-x: Adjust UART clock
The UART uses internal SCIF clock except on R8A7795 H3 WS1.0 .
Use the internal clock and ignore the early version of the chip.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-05-22 04:38:27 +09:00
Marek Vasut
f7fda5d1c0 ARM: rmobile: salvator-x: Set default device tree
Set default device tree file in the salvator-x_defconfig
and use it in the environment.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-05-22 04:38:26 +09:00
Marek Vasut
c94cb71d95 ARM: rmobile: salvator-x: Move OF_LIBFDT and CMD_FDT to board config
Move these two Kconfig symbols to the salvator-x_defconfig.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-05-22 04:38:26 +09:00
Marek Vasut
2dea3b3e7b ARM: rmobile: Add R8A7796 support
Add Kconfig entry for the R8A7796 RCar M3 SoC.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-05-22 04:38:26 +09:00
Marek Vasut
43c8352e3e ARM: rmobile: Update link address to match latest BL2
Update the CONFIG_SYS_TEXT_BASE to match BL2 Rev.1.0.9 and newer,
which loads the U-Boot to 0x50000000 .

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-05-22 04:38:25 +09:00
Tom Rini
a375ff8e14 Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2017-05-18 17:17:45 -04:00
Ley Foon Tan
1b2594030d arm: socfpga: Add config and defconfig for Arria 10
Add config and defconfig for the Arria10 and update socfpga_common.h.

Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2017-05-18 11:33:19 +02:00
Ley Foon Tan
827e6a7e0d arm: socfpga: Add reset driver support for Arria 10
Add reset driver support for Arria 10.

Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2017-05-18 11:33:17 +02:00
Peng Fan
d1e204b566 imx: mx7dsabresd: switch to DM USB
Switch to use DM USB.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2017-05-18 11:24:34 +02:00
Peng Fan
6fbbcfdf06 imx: mx7dsabresd: enable more DM drivers
Enable more DM drivers. The imx I2C/MMC DM drivers needs DM_GPIO
enabled. The 74x164 drivers needs SOFT_SPI and DM_GPIO enabled.
So needs to enable them together.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2017-05-18 11:24:34 +02:00
Peng Fan
993274f485 arm: dts: imx7: sync with Linux
Sync with Linux commit 308ac756("Merge tag 'gpio-v4.11-3'").

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefan Agner <stefan.agner@toradex.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2017-05-18 11:24:33 +02:00
Jagan Teki
6f1f3f59ed engicam: Set fdt_file env during run-time
Set fdt_file env variable during board_late_init

Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-05-18 11:23:31 +02:00
Jagan Teki
08273bc260 geam6ul: Add mmc_late_init
Let the runtime code can set the mmcdev and mmcroot based
on the devno using mmc_get_env_dev instead of defining
separately in build-time configs using mmc_late_init func.

Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-05-18 11:23:31 +02:00
Jagan Teki
9786496cdc geam6ul: Add modeboot env via board_late_init
Add runtime, modeboot env which is setting mmcboot, or
nandboot based on the bootdevice so-that conditional
macros b/w MMC and NAND for CONFIG_BOOTCOMMAND should
be avoided in config files.

Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-05-18 11:23:31 +02:00
Jagan Teki
4bbd40596b icorem6: Add mmc_late_init
Let the runtime code can set the mmcdev and mmcroot based
on the devno using mmc_get_env_dev instead of defining
separately in build-time configs using mmc_late_init func.

Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-05-18 11:23:31 +02:00
Jagan Teki
98f5661033 icorem6: Add modeboot env via board_late_init
Add runtime, modeboot env which is setting mmcboot, or
nandboot based on the bootdevice so-that conditional
macros b/w MMC and NAND for CONFIG_BOOTCOMMAND should
be avoided in config files.

Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-05-18 11:23:31 +02:00
Fabio Estevam
9e408a39b4 mx25pdk: Add fuse API support
Select CONFIG_FSL_IIM and CONFIG_CMD_FUSE so that the fuse API can
be used.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-05-18 11:23:31 +02:00
Tom Rini
fa8967cfba Merge git://git.denx.de/u-boot-uniphier
- Add workaround code to make LD20 SoC boot from ARM Trusted Firmware
- Sync DT with Linux to fix DTC warnings
- Add new SoC support code
- Misc fix, updates
2017-05-17 14:13:58 -04:00
Siarhei Siamashka
7f0ef5a945 sunxi: Store the device tree name in the SPL header
This patch updates the mksunxiboot tool to optionally add
the default device tree name string to the SPL header. This
information can be used by the firmware upgrade tools to
protect users from harming themselves by trying to upgrade
to an incompatible bootloader.

The primary use case here is a non-removable bootable media
(such as NAND, eMMC or SPI flash), which already may have
a properly working, but a little bit outdated bootloader
installed. For example, the user may download or build a
new U-Boot image for "Cubieboard", and then attemept to
install it on a "Cubieboard2" hardware by mistake as a
replacement for the already existing bootloader. If this
happens, the flash programming tool can identify this
problem and warn the user.

The size of the SPL header is also increased from 64 bytes
to 96 bytes to provide enough space for the device tree name
string.
[Andre: split patch to remove OF_LIST hash feature]

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2017-05-17 23:23:58 +05:30
Andre Przywara
d29adf8eef sunxi: enable automatic FIT build for 64-bit SoCs
The Allwinner SoCs with 64-bit cores use an ARM Trusted Firmware binary,
which needs to be loaded alongside U-Boot proper.
Set the respective Kconfig options to let them select this feature and
also automatically build the FIT image.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[Rename Kconfig path to arch/arm/mach-sunxi/Kconfig]
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-05-17 23:23:25 +05:30
Andre Przywara
54522c9291 sunxi: A64: move SPL stack to end of SRAM A2
The SPL stack is usually located at the end of SRAM A1, where it grows
towards the end of the SPL.
For the really big AArch64 binaries the stack overwrites code pretty
soon, so move the SPL stack to the end of SRAM A2, which is unused at this
time.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Jagan Teki <jagan@openedev.com>
2017-05-17 23:21:02 +05:30
Masahiro Yamada
edee114a8b ARM: uniphier: move kernel physical base to 0x82080000
Reserve enough space below the kernel base.
The assumed address map is:
  80000000 - 80ffffff : for IPP
  81000000 - 81ffffff : for ARM secure
  82000000 -          : for Linux

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-05-17 21:51:04 +09:00
Masahiro Yamada
8d3064d9a9 ARM: uniphier: add usbupdate command
This script command will be useful to update boot images in the
USB storage.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-05-17 21:46:20 +09:00
Stefan Roese
426f99fa98 dm: core: Add DM_FLAG_OS_PREPARE flag
This new flag can be added to DM device drivers, which need to do some
final configuration before U-Boot exits and the OS (e.g. Linux) is
started. The remove functions of those drivers will get called at
this stage to do these last-stage configuration steps.

Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
2017-05-17 17:13:06 +08:00
Simon Glass
ddb3ac3c71 x86: Convert MMC to driver model
Convert the pci_mmc driver over to driver model and migrate all x86 boards
that use it.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
2017-05-17 17:13:06 +08:00
Tom Rini
4125bbcef6 Merge branch 'master' of git://git.denx.de/u-boot-mmc
- Add #undef CONFIG_DM_MMC_OPS to omap3_logic in the SPL build case, to
  match other TI platforms in the same situation.

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-05-16 08:10:50 -04:00
Tom Rini
d09ec7f816 Merge branch 'master' of git://git.denx.de/u-boot-video 2017-05-15 20:16:02 -04:00
Philipp Tomsich
10ba6b3339 video: bmp: rename CONFIG_BMP_24BMP to CONFIG_BMP_24BPP
Due to a typo, the 24 bit-per-pixel configuration ends in 24BMP
instead of 24BPP. This change renames it throughout the source tree
for consistency and to make moving these options into Kconfig easier
and less error-prone.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
2017-05-15 20:55:13 +02:00
Jernej Skrabec
43c6bdd020 edid: Add HDMI flag to timing info
Some DVI monitors don't show anything in HDMI mode since audio stream
confuses them. To solve this situation, this commit adds HDMI flag in
timing data and sets it accordingly during edid parsing.

First existence of extension block is checked. If it exists and it is
CEA861 extension, then data blocks are checked for presence of HDMI
vendor specific data block. If it is present, HDMI flag is set.

Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-15 20:32:12 +02:00
Tom Rini
cb33bda44f Merge branch 'master' of git://git.denx.de/u-boot-i2c 2017-05-15 13:01:26 -04:00
Tom Rini
1d1ab61c32 Kconfig: OMAP: USB: Migrate CONFIG_USB_EHCI_OMAP to Kconfig
Follow the exiting logic for the i.MX options when migrating this
option.

Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marek Vasut <marex@denx.de>
2017-05-15 13:00:26 -04:00
Tom Rini
80f1f3204a Kconfig: USB: Migrate existing USB_EHCI_xxx options
The following options are migrated over fully now:
- USB_EHCI_ATMEL
- USB_EHCI_MARVELL
- USB_EHCI_MX6
- USB_EHCI_MX7
- USB_EHCI_MSM
- USB_EHCI_ZYNQ
- USB_EHCI_GENERIC

This also requires fixing the depends on USB_EHCI_MARVELL as it's used
by Orion5X and Kirkwood as well.

Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marek Vasut <marex@denx.de>
2017-05-15 13:00:26 -04:00
Tom Rini
64d6ac5bc4 Kconfig: USB: Migrate CONFIG_USB_EHCI_HCD users to Kconfig
Migrate the rest of the users of CONFIG_USB_EHCI_HCD over to Kconfig.
For a few SoCs, imply or default y this if USB is enabled.  In some
cases we had not already migrated to CONFIG_USB so do that as well.

Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marek Vasut <marex@denx.de>
2017-05-15 13:00:21 -04:00
Tom Rini
8850c5d57c Kconfig: USB: Migrate CONFIG_USB_EHCI to CONFIG_USB_EHCI_HCD
In order to be able to migrate the various SoC EHCI CONFIG options we
first need to finish the switch from CONFIG_USB_EHCI to
CONFIG_USB_EHCI_HCD.

Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marek Vasut <marex@denx.de>
2017-05-15 10:40:05 -04:00
Tom Rini
86a0307918 whitelist: Drop more unused OMAP symbols
The symbol CONFIG_OMAP3_LOGIC_USE_NEW_PRODUCT_ID was recently dropped
from usage and CONFIG_OMAP3_MICRON_DDR is unused in code.

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-05-15 10:40:03 -04:00
Tom Rini
897f706200 watchdog: Migrate OMAP_WATCHDOG to Kconfig
Move this entry to Kconfig.  As it is a hardware watchdog, select
HW_WATCHDOG.  While we could default to enabling this for all platforms,
it is currently only enabled by default on AM33XX, so keep that logic
today.

Cc: Roger Meier <r.meier@siemens.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-05-15 10:40:02 -04:00
Tom Rini
68ccab5193 omap3: Migrate CONFIG_OMAP3_GPIO_X to Kconfig
The symbols CONFIG_OMAP3_GPIO_X control if we enable the clocks for a
given GPIO bank in U-Boot.  select the required banks for each target.
In some cases we need to also migrate from CONFIG_USB_EHCI (deprecated,
in include/configs/) to CONFIG_USB_EHCI_HCD as we only require the GPIO
bank to be enabled if USB is also enabled.

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-05-15 10:40:00 -04:00
Tom Rini
29cb2b3b90 gpio: Move OMAP_GPIO to Kconfig
This driver is used often enough such that we want to have this enabled
by default on any ARCH_OMAP2PLUS board, and this only compiles on
ARCH_OMAP2PLUS due to required defines, so mark that as the depends.

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-05-15 10:40:00 -04:00
Tom Rini
bdf10677a9 omap3: Drop unused CONFIG_OMAP3_xxx board defines
We no longer have a need for a per-board CONFIG_OMAP3_xxx define (we
have CONFIG_TARGET_xxx when this is required), so drop these unused
references.

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-05-15 10:39:59 -04:00
Tom Rini
77777f769f omap4: Drop redundant CONFIG_OMAP4430 symbol
While there are a few different OMAP4 SoCs, today we always set
CONFIG_OMAP4430 and CONFIG_OMAP44XX.  Convert the few test of
CONFIG_OMAP4430 to CONFIG_OMAP44XX.

Cc: Marek Vasut <marex@denx.de>
Cc: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-05-15 10:39:59 -04:00
Tom Rini
864896be3b omap3: Drop CONFIG_OMAP3_EVM, switch to CONFIG_TARGET_OMAP3_EVM when needed
We make use of CONFIG_OMAP3_EVM today to know when to do a specific
tweak in MUSB.  This can be tested on via CONFIG_TARGET_OMAP3_EVM
instead, so switch there so we can drop the now unused symbol
CONFIG_OMAP3_EVM.  In investigating what to do about the symbol usage we
see that the cairo board defines the same function, but never called it
(as it does not define CONFIG_OMAP3_EVM) and was just returning anyhow,
so drop that function from that board.

Cc: "Albert ARIBAUD (3ADEV)" <albert.aribaud@3adev.fr>
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-05-15 10:39:58 -04:00
Tom Rini
d87f82967f omap5: Migrate CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC to Kconfig
While in theory this value could be used in places outside of "omap5"
(such as OMAP4), we only make use of it today in OMAP5, so place the
Kconfig entry there.  Given that Kconfig lets us provide a default, we
drop CONFIG_DEFAULT_OMAP_RESET_TIME_MAX_USEC entirely.  The contents of
doc/README.omap-reset-time make a good help entry, so adjust them
slightly and delete the file.  Move the comment about range to where we
use the value now, and have Kconfig enforce the upper bound.

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-05-15 10:39:57 -04:00
Tom Rini
89024ddc9e TI: Drop 'CONFIG_OMAP'
In the two cases in the code where we use CONFIG_OMAP as a useful test
currently we can make use of CONFIG_ARCH_OMAP2PLUS instead.  With that
changed we can drop all defines of CONFIG_OMAP.  While in here,
CONFIG_OMAP3430 is only defined and then never used, so drop.

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-05-15 10:39:56 -04:00
Kever Yang
bcc1726a7b spl: add support to booting with ATF
ATF(ARM Trusted Firmware) is used by ARM arch64 SoCs, find more infomation
about ATF at: https://github.com/ARM-software/arm-trusted-firmware

SPL is considered as BL2 in ATF terminology, it needs to load other parts
of ATF binary like BL31, BL32, SCP-BL30, and BL33(U-Boot). And needs to
prepare the parameter for BL31 which including entry and image information
for all other images. Then the SPL handle PC to BL31 with the parameter,
the BL31 will do the rest of work and at last get into U-Boot(BL33).

This patch needs work with patches from Andre for SPL support multi
binary in FIT.

The entry point of bl31 and bl33 are still using hard code because we
still can not get them from the FIT image information.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-05-15 10:38:09 -04:00
Jean-Jacques Hiblot
e83d61a57d include: config: am335x: disable DM_MMC_OPS if DM_MMC is disabled
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-15 13:51:31 +09:00
Simon Glass
b0103f33b4 i2c: Drop CONFIG_SYS_I2C_BOARD_LATE_INIT
This option is not used by any boards. Drop it.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-05-15 06:18:51 +02:00
Simon Glass
eb5ba3aefd i2c: Drop use of CONFIG_I2C_HARD
This option is pretty old. It predates CONFIG_SYS_I2C which is itself
deprecated in favour of driver model. Disable it for all boards.

Also drop I2C options which depend on this.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-05-15 06:17:09 +02:00
Tom Rini
22f3368e71 Merge branch 'master' of git://git.denx.de/u-boot-mips 2017-05-13 16:45:35 -04:00
Tom Rini
f552d69246 Kconfig: Drop CONFIG_EMAC_MDIO_PHY_NUM
This particular macro hasn't been used in the code for some time, remove
these references that were missed.

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-05-12 08:37:36 -04:00
Peng Fan
25112101d0 asm-generic: global_data: change timebase_l/h to unsigned int
Change type of timebase_l/h to unsigned int.
>From lib/time.c: ((uint64_t)gd->timebase_h << 32) | gd->timebase_l;
This piece code is based on that timebase_h and timebase_l are
32bits width, so change the type to unsigned int.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Eddie Cai <eddie.cai.linux@gmail.com>
Cc: Jagan Teki <jteki@openedev.com>
Cc: York Sun <york.sun@nxp.com>
Cc: "Robert P. J. Day" <rpjday@crashcourse.ca>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-12 08:37:35 -04:00
Lokesh Vutla
59041a5084 arm: am33xx: Fix MPU opp selection
Update MPU frequencies and voltages as per the latest
DM[1] dated: OCT 2011 Revised APRIL 2016, Section 5.4.
Below is the consolidated data:

MPU values for PG 2.0 and later(Package ZCZ and ZCE):

 -------------------------------------------------------
|	|	  ZCZ		|	  ZCE		|
|-------------------------------------------------------|
|	| VDD[V]   | ARM [MHz]	| VDD[V]   | ARM [MHz]  |
|-------|----------|------------|----------|------------|
| NITRO |  1.325   |   1000     |   NA     |    NA      |
|-------|----------|------------|----------|------------|
| TURBO |   1.26   |    800	|   NA     |    NA      |
|-------|----------|------------|----------|------------|
|OPP120 |   1.20   |    720     |   NA     |    NA      |
|-------|----------|------------|----------|------------|
|OPP100 |   1.10   |    600     |   1.10   |    600     |
|-------|----------|------------|----------|------------|
| OPP50 |   0.95   |    300     |   0.95   |    300     |
 -------------------------------------------------------

There is no eFuse blown on PG1.0 Silicons due to which there is
no way to detect the maximum frequencies supported. So default
to OPP100 for which both frequency and voltages are common on both
the packages.

[1] http://www.ti.com/lit/ds/symlink/am3356.pdf

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-05-12 08:37:12 -04:00
Lokesh Vutla
c187dd685a configs: convert CONFIG_SYS_MPUCLK to Kconfig
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-05-12 08:37:11 -04:00
Paul Burton
dc55db4965 boston: Bump CONFIG_SYS_BOOTM_LEN to 64MiB
The default value of CONFIG_SYS_BOOTM_LEN is too small for typical
boston Linux kernels. Increase the limit to 64MB, which covers current
kernels with plenty of breathing room.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-12 13:29:50 +02:00
Lokesh Vutla
238205f1b3 configs: am335x_evm: Enable SPL_DM
Enable SPL_DM on all AM335x based TI platforms.

http://patchwork.ozlabs.org/patch/751300/
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-05-11 22:21:29 -04:00
Lokesh Vutla
3a517fdc2b configs: am335x_evm: Use omap2 generic spl load script
No reason to use a separate load script for am33xx than using
omap-common load script.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-05-11 22:21:28 -04:00
Lokesh Vutla
a52cf086ac serial: omap: Support debug UART
Add debug UART functions to permit omap specific ns16550 to
provide an early debug UART. This is mostly in common with
DEBUG_UART_NS16550 except for Mode definition register which
is required for selecting UART mode(16x auto-baud or 13x mode).

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-05-11 22:21:27 -04:00
Alex Deymo
88b6329cce disk: Return the partition number in part_get_info_by_name()
Similar to what blk_get_device_part_str() does, this patch makes
part_get_info_by_name() return the partition number in case of a match.
This is useful when the partition number is needed and not just the
descriptor.

Signed-off-by: Alex Deymo <deymo@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-11 22:03:37 -04:00
Alex Deymo
210a7176ee image: Update include/android_image.h
Update the Android image header format to the latest version published
in AOSP. The original code moved to a new repository, so this patch also
updates the reference to that path.

Signed-off-by: Alex Deymo <deymo@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-11 22:03:37 -04:00
Tom Rini
1f5541c881 Merge git://git.denx.de/u-boot-rockchip
This adds a new firefly-rk3399 board, MIPI support for rk3399 and
rk3288, rk818 pmic support, mkimage improvements for rockchip and a few
other things.
2017-05-10 17:40:11 -04:00
Tom Rini
102d86552a Merge branch 'master' of git://git.denx.de/u-boot-mips 2017-05-10 15:50:21 -04:00
Jacob Chen
453c5a927c power: rk808: rename to rk8xx
Since this driver can be used for rk8xx series pmic,
let's rename rk808 to rk8xx, to make it clear.

Configs parts are done by sed -i "s/RK808/RK8XX/g" `grep RK808 -lr ./`

Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
2017-05-10 13:37:22 -06:00
Jacob Chen
d77af8a8c9 power: pmic: rk808: add RK818 support
The RK818 chip is a Power Management IC (PMIC) for multimedia and handheld
devices.

For boards use rk818, the input current should be set in the early stage, before
ddr initialization.

Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
2017-05-10 13:37:22 -06:00
Jacob Chen
1daa93c0b4 power: pmic: append rk818 regs to rk808
Both RK808 and RK818 chips are using a similar register map,
so we can reuse them.

I have also add reg prefix to exist registers, to keep them same style.

Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-10 13:37:22 -06:00
Jonas Karlman
8880efbd1f i2c_eeprom: add read and write functions
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-10 13:37:22 -06:00
Kever Yang
0b60111aa6 power: regulator: pwm: support pwm polarity setting
The latest kernel PWM drivers enable the polarity settings. When system
run from U-Boot to kerenl, if there are differences in polarity set or
duty cycle, the PMW will re-init:
  close -> set polarity and duty cycle -> enable the PWM.
The power supply controled by pwm regulator may have voltage shaking,
which lead to the system not stable.

Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
2017-05-10 13:37:21 -06:00
Kever Yang
dde2223372 rockchip: dts: rk3399: sync with kernel dts
The kernel dts has update a lot since the first time we commit rk3399.dtsi,
sync with kernel for further development.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
2017-05-10 13:37:21 -06:00
Kever Yang
fd9884e292 rockchip: dts: evb-rk3399: add gmac support
Enable gmac for evb-rk3399.

Change-Id: I85e35667e08e22e38577e63eb0e65731fc9c69b6
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2017-05-10 13:37:21 -06:00
Philipp Tomsich
3e75c07ddb rockchip: spl: rk3399: spi: enable SPL_SPI_LOAD if SPI is enabled for SPL
To include the ability to load from an SPI flash in SPL, it's not
sufficient to define SPL_SPI_SUPPORT and SPL_SPI_FLASH_SUPPORT via
Kconfig... so we conditionally define SPL_SPI_LOAD if SPI support
is already enabled for SPL via Kconfig.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
2017-05-10 13:37:21 -06:00
Álvaro Fernández Rojas
a1b5e5e7c1 mips: bmips: add bcm6328-power-domain driver support for BCM63268
This driver can control up to 32 power domains.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2017-05-10 16:16:09 +02:00
Álvaro Fernández Rojas
9a5cb22fda mips: bmips: add bcm6328-power-domain driver support for BCM6328
This driver can control up to 32 power domains.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2017-05-10 16:16:09 +02:00
Álvaro Fernández Rojas
02bb1fa09e mips: bmips: add bcm6345-rst driver support for BCM63268
This driver can control up to 32 clocks.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-10 16:16:09 +02:00
Álvaro Fernández Rojas
78118211fb mips: bmips: add bcm6345-rst driver support for BCM6328
This driver can control up to 32 clocks.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-10 16:16:09 +02:00
Álvaro Fernández Rojas
efe8b9d012 mips: bmips: add bcm6345-rst driver support for BCM6358
This driver can control up to 32 resets.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-10 16:16:09 +02:00
Álvaro Fernández Rojas
969ebdb930 mips: bmips: add bcm6345-clk driver support for BCM63268
This driver can control up to 32 clocks.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-10 16:16:09 +02:00
Álvaro Fernández Rojas
5b14e13c24 mips: bmips: add bcm6345-clk driver support for BCM6328
This driver can control up to 32 clocks.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-10 16:16:09 +02:00
Álvaro Fernández Rojas
70789bd2a5 mips: bmips: add bcm6345-clk driver support for BCM6358
This driver can control up to 32 clocks.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-10 16:16:09 +02:00
Álvaro Fernández Rojas
a186d2630b mips: bmips: add NeufBox 4 (Sercomm) board
This serves as an example for bcm6358-leds.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-10 16:16:09 +02:00
Álvaro Fernández Rojas
77ca99d1a0 MIPS: add BMIPS Comtrend VR-3032u board
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-10 16:16:09 +02:00
Álvaro Fernández Rojas
6a235bb87b MIPS: add support for Broadcom MIPS BCM63268 SoC family
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-10 16:16:09 +02:00
Álvaro Fernández Rojas
0642f485dc MIPS: add BMIPS Comtrend AR-5387un board
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-10 16:16:09 +02:00
Álvaro Fernández Rojas
6471a225e7 MIPS: add support for Broadcom MIPS BCM6328 SoC family
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-10 16:16:09 +02:00
Álvaro Fernández Rojas
4a2b2724a2 MIPS: add BMIPS Huawei HG556a board
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-10 16:16:09 +02:00
Álvaro Fernández Rojas
e30d2bd40e MIPS: add support for Broadcom MIPS BCM6358 SoC family
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-10 16:16:09 +02:00
Álvaro Fernández Rojas
ee422142f4 MIPS: add initial infrastructure for Broadcom MIPS SoCs
CFE checks CPU Thread in a different way (using register $22):
mfc0	t1, C0_BCM_CONFIG, 3 # $22
li	t2, CP0_CMT_TPID # (1 << 31)
and	t1, t2
bnez	t1, 2f	# if we are running on thread 1, skip init
nop

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-10 16:16:09 +02:00
Adam Ford
05b8dc5cd3 power: twl4030: Remove CONFIG_TWL4030_POWER from include/configs
With the addition of Kconfig now having CONFIG_TWL4030_POWER and
with that being the default when OMAP34XX is selected, this
is no longer needed in include/configs and can be removed from the
whitelist.

This has only been tested on logic PD DM3730 using ti_omap3_common.h

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-09 20:35:38 -04:00
Adam Ford
15fde737fc omap3_logic: Add Device Tree Support and more DM drivers
This patch also removes all the excessive code for NS16550 intiailization
as the device tree can do that now.  This also adds DM_I2C and DM_MMC
since the overlying drivers have the built-in support already.  The
corresponding include/config/omap3_logic.h also reduced in size
due to the new device tree support.

Signed-off-by: Adam Ford <aford173@gmail.com>

Changes in V2:
  Retain Auto-detect ability between SOM-LV and Torpedo
  Split this off from the device sub submissions
2017-05-09 20:35:38 -04:00
Adam Ford
cac4d6a680 omap3630: Copy Device tree from Linux 4.9.y stable
Add device tree support to allow for CONFIG_OF_CONTROL in OMAP3630 boards.
DM3730 can use this same device tree.

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-05-09 20:35:36 -04:00
Alex Deymo
82f766d1d2 Allow boards to initialize the DT at runtime.
In some boards like the Raspberry Pi the initial bootloader will pass
a DT to the kernel. When using U-Boot as such kernel, the board code in
U-Boot should be able to provide U-Boot with this, already assembled
device tree blob.

This patch introduces a new config option CONFIG_OF_BOARD to use instead
of CONFIG_OF_EMBED or CONFIG_OF_SEPARATE which will initialize the DT
from a board-specific funtion instead of bundling one with U-Boot or as
a separated file. This allows boards like the Raspberry Pi to reuse the
device tree passed from the bootcode.bin and start.elf firmware
files, including the run-time selected device tree overlays.

Signed-off-by: Alex Deymo <deymo@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-09 20:35:06 -04:00
Simon Glass
ea843b6dab dm: video: arm: rpi: Convert to use driver model for video
Adjust the video driver to work with driver model and move over existing
baords. There is no need to keep the old code.

We can also drop setting of CONFIG_FB_ADDR since driver model doesn't have
this problem.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
2017-05-09 20:27:17 -04:00
Simon Glass
25085236c6 dm: arm: rpi: Move to driver model for USB
Start using driver model for USB on the Raspberry Pi. The dwc2 supports
this now so this is just a config change.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-05-09 20:19:31 -04:00
Simon Glass
91b00b5fcc arm: rpi: Drop CONFIG_CONS_INDEX
This is not needed now that serial uses driver model.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-05-09 20:19:05 -04:00
Tom Rini
dd9999d5f4 Merge git://git.denx.de/u-boot-dm 2017-05-09 16:11:36 -04:00
Jean-Jacques Hiblot
72e5016f87 drivers: phy: add generic PHY framework
The PHY framework provides a set of APIs to control a PHY. This API is
derived from the linux version of the generic PHY framework.
Currently the API supports init(), deinit(), power_on, power_off() and
reset(). The framework provides a way to get a reference to a phy from the
device-tree.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-09 12:14:16 -06:00
Wenyou Yang
0b8908f9c3 configs: at91sam9263ek: Update for DT and DM support
Update the configuration files to support the device tree and driver
model. The device clock and pins configuration are handled by the
clock and the pinctrl drivers respectively.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-09 12:14:16 -06:00
Wenyou Yang
2011dca2c1 configs: at91sam9rlek: Update for DT and DM support
Update the configuration files to support the device tree and driver
model. The device clock and pins configuration are handled by the
clock and the pinctrl drivers respectively.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-09 12:14:16 -06:00
Wenyou Yang
83f1c2ef30 configs: at91sam9260ek/9g20ek: Update for DT and DM
Update the configuration files to support the device tree and driver
model. The device clock and pins configuration are handled by the
clock and the pinctrl drivers respectively.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-09 12:14:16 -06:00
Wenyou Yang
59b37122b1 configs: at91sam9m10g45ek: Update to support DM/DT
Update the configuration files to support the device tree and driver
model. The device clock and pins configuration are handled by the
clock and the pinctrl drivers respectively.

Because the limitation of internal SRAM size, the SPL with driver
model can't be supported, disable the SPL option.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-09 12:14:15 -06:00
Wenyou Yang
0ab5433da2 configs: at91sam9n12ek: Update for DT and DM support
Update the configuration files to support the device tree and driver
model. The device clock and pins configuration are handled by the
clock and the pinctrl drivers respectively.

Because the limitation of internal SRAM size, the SPL with driver
model can't be supported, disable the SPL option.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-09 12:14:15 -06:00
Wenyou Yang
74631b69d6 configs: at91sam9x5ek: Update to support DM/DT
Update the configuration files to support the device tree and driver
model. The device clock and pins configuration are handled by the
clock and the pinctrl drivers respectively.

Because the limitation of internal SRAM size, the SPL with driver
model can't be supported, disable the SPL option.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-09 12:14:15 -06:00
Wenyou Yang
62904b7346 configs: sama5d2_xplained: update for SPL
Enable config options to support the SPL, increase the malloc
memory size for the SPL and board_init_f stage and increase
the memory space for the SPL binary.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
2017-05-09 12:14:15 -06:00
Wenyou Yang
d4ce9e7bbf configs: sama5d2_xplained: enable CONFIG_DM_ETH
Enable CONFIG_DM_ETH to make MACB to support driver model.

Because the USB Ether doesn't support driver model so far,
remove this feature.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
2017-05-09 12:14:15 -06:00
Chris Packham
e38f5fc8d8 ARM: mvebu: switch db-88f6820-amc to DM for i2c
Move existing configuration from header file to defconfig or dts as
appropriate.

Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
2017-05-09 13:38:18 +02:00
Igal Liberman
b617a0d7b8 phy: marvell: cp110: add 5G XFI mode
This patch adds the option to configure a comphy to 5G XFI mode.

In order to configure the comphy to 5G XFI, update
the comphy node in the device-tree:
	phy2 {
		phy-type = <PHY_TYPE_SFI>;
		phy-speed = <PHY_SPEED_5_15625G>;
	};

Signed-off-by: Igal Liberman <igall@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
2017-05-09 13:38:18 +02:00
Stefan Roese
6ecc0b1cdf phy: marvell: add IGNORE COMPHY type
This type tells u-boot to preserve the COMPHY settings as is
it is usefull in situations where the COMPHY was initialized by
earlier firmware.
Note that IGNORE is different from UNCONNECTED since setting
UNCONNECTED type will disconnect the COMPHY in the COMPHY MUX
which is a desired behaviour

Signed-off-by: Yehuda Yitschak <yehuday@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2017-05-09 13:38:18 +02:00
Stefan Roese
e89acc4bf1 phy: marvell: cp110: update utmi phy connection type
UTMI_PHY_TO_USB_HOST was used in USB3 UTMI dts node only, but there will
be USB2 UTMI dts node for some SoCs that have got USB2 controller, so rename
TO_USB_HOST to TO_USB3_HOST to distinguish TO_USB2_HOST in later on patches.

Signed-off-by: zachary <zhangzg@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2017-05-09 13:38:18 +02:00
Stefan Roese
cb686454c7 phy: marvell: Replace PHY_TYPE_KR with PHY_TYPE_SFI
Use correct naming as done in the latest Marvell U-Boot version as well.

Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2017-05-09 13:38:18 +02:00
Konstantin Porotchkin
f59472e84e arm64: mvebu: a8k: Add NAND configuration parameters
Add NAND configuration parameters to A8K shared config file.
Add defconfig for db-88f7040 board with boot from NAND setup.

Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2017-05-09 13:38:18 +02:00
Tom Rini
a6d4cd4778 Merge branch 'master' of git://git.denx.de/u-boot-sunxi 2017-05-08 15:44:44 -04:00
Lokesh Vutla
ee3c6532be ARM: keystone2: Add support for getting external clock dynamically
One some keystone2 platforms like K2G ICE, there is an option
to switch between 24MHz or 25MHz as sysclk. But the existing
driver assumes it is always 24MHz. Add support for getting
all reference clocks dynamically by reading boot pins.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-05-08 12:34:29 -04:00
maxims@google.com
3b95902d47 aspeed: Add support for Clocks needed by MACs
Add support for clocks needed by MACs to ast2500 clock driver.
The clocks are D2-PLL, which is used by both MACs and PCLK_MAC1 and
PCLK_MAC2 for MAC1 and MAC2 respectively.

The rate of D2-PLL is hardcoded to 250MHz -- the value used in Aspeed
SDK. It is not entirely clear from the datasheet how this clock is used
by MACs, so not clear if the rate would ever need to be different. So,
for now, hardcoding it is probably safer.

The rate of PCLK_MAC{1,2} is chosen based on MAC speed selected through
hardware strapping.

So, the network driver would only need to enable these clocks, no need
to configure the rate.

Signed-off-by: Maxim Sloyko <maxims@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-08 11:57:35 -04:00
maxims@google.com
c93adc08f3 aspeed: Device Tree configuration for Reset Driver
Add Reset Driver configuration to ast2500 SoC Device Tree and bindings
for various reset signals

Signed-off-by: Maxim Sloyko <maxims@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-08 11:57:32 -04:00
maxims@google.com
0753bc2d30 dm: Simple Watchdog uclass
This is a simple uclass for Watchdog Timers. It has four operations:
start, restart, reset, stop. Drivers must implement start, restart and
stop operations, while implementing reset is optional: It's default
implementation expires watchdog timer in one clock tick.

Signed-off-by: Maxim Sloyko <maxims@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-08 11:57:30 -04:00
Pau Pajuelo
2e0c6f38f3 igep003x: Add netboot support
netboot allows to boot an external image using TFTP and NFS protocols

Signed-off-by: Pau Pajuelo <ppajuelo@iseebcn.com>
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Tested-by: Pau Pajuelo <ppajuel@gmail.com>
2017-05-08 11:57:27 -04:00
Pau Pajuelo
09533e5de7 igep003x: Add support for IGEP SMARC AM335x
The IGEP SMARC AM335x is an industrial processor module with
following highlights:

  o AM3352 TI processor (Up to AM3359)
  o Cortex-A8 ARM CPU
  o SMARC form factor module
  o Up to 512 MB DDR3 SDRAM / 512 MB FLASH
  o WiFi a/b/g/n and Bluetooth v4.0 on-board
  o Ethernet 10/100/1000 Mbps and 10/100 Mbps controller on-board
  o JTAG debug connector available
  o Designed for industrial range purposes

Signed-off-by: Pau Pajuelo <ppajuelo@iseebcn.com>
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Tested-by: Pau Pajuelo <ppajuel@gmail.com>
2017-05-08 11:57:27 -04:00
Ladislav Michl
3607e0f86f igep003x: UBIize
Convert IGEP board to use UBI volumes for U-Boot, its environment and
kernel. With exception of first four sectors read by SoC BootROM whole
NAND is UBI managed.

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Heiko Schocher<hs@denx.de>
Tested-by: Pau Pajuelo <ppajuel@gmail.com>
2017-05-08 11:57:27 -04:00
Ladislav Michl
a96c08f509 igep0033: Rename to igep003x
Rename igep0033 to igep003x as IGEP SMARC AM335x module (igep0034)
can use the same source files.

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Tested-by: Pau Pajuelo <ppajuel@gmail.com>
2017-05-08 11:57:26 -04:00
Vikas Manocha
fddd70ef37 stm32f7: remove not needed configuration from board config
This patch removes:
	- CONFIG_CMD_MEM: enabled by default
	- CONFIG_DESIGNWARE_ETH : not being used anywhere.

Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
2017-05-08 11:57:25 -04:00
Vikas Manocha
bfea69ad27 stm32f7: sdram: correct sdram configuration as per micron sdram
Actually the sdram memory on stm32f746 discovery board is micron part
MT48LC_4M32_B2B5_6A. This patch does the modification required in the
device tree node & driver for the same.

Also we are passing here all the timing parameters in terms of clock
cycles, so no need to convert time(ns or ms) to cycles.

Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
2017-05-08 11:57:22 -04:00
Vikas Manocha
a241c241cf stm32f7: enable board info read from device tree
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
2017-05-08 11:57:22 -04:00
Vikas Manocha
57af3cc32a stm32f7: stm32f746-disco: read memory info from device tree
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
2017-05-08 11:57:21 -04:00
Vikas Manocha
2f80a9f72e stm32f746: to switch on user LED1 & read user button
All discovery boards have one user button & one user LED. Here we are
just reading the button status & switching ON the user LED.

Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
2017-05-08 11:57:21 -04:00
Vikas Manocha
280057bd7d stm32f7: use stm32f7 gpio driver supporting driver model
With this gpio driver supporting DM, there is no need to enable clocks
for different gpios (for pin muxing) in the board specific code.

Need to increase the allocatable area required before relocation from 0x400 to
0xC00 becuase of 10 new gpio devices(& new gpio class) added in device tree.

Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-08 11:57:21 -04:00
Vikas Manocha
6c9a10034a stm32f7: sdram: use sdram device tree node to configure sdram controller
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
2017-05-08 11:39:05 -04:00
Vikas Manocha
5bf5250e9d spl: make image arg or fdt blob address reconfigurable
At present fdt blob or argument address being passed to kernel is fixed at
compile time using macro CONFIG_SYS_SPL_ARGS_ADDR. FDT blob from
different media like nand, nor flash are copied to the address pointed
by the macro.
The problem is, it makes args/fdt blob compulsory to copy which is not required
in cases like for NOR Flash. This patch removes this limitation.

Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
2017-05-08 11:38:40 -04:00
Uri Mashiach
e627290ac6 arm: am57xx: cl-som-am57x: fix USB scan
USB bus scan attempt:
----------------------------------cut----------------------------------
=> usb start
starting USB...
USB0:   Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.00
scanning bus 0 for devices... data abort
pc : [<fff6240e>]          lr : [<fff623b3>]
reloc pc : [<8081b40e>]    lr : [<8081b3b3>]
sp : fdf42930  ip : fdf42960     fp : 00000000
r10: 00000001  r9 : fdf42ef0     r8 : 48890020
r7 : 00000002  r6 : fffa5840     r5 : fff8b140  r4 : fdf429c0
r3 : 00000000  r2 : 00000004     r1 : 00000000  r0 : 00000000
Flags: nZcv  IRQs off  FIQs off  Mode SVC_32
Resetting CPU ...

resetting ...
----------------------------------cut----------------------------------

Fix by enabling USB configuration in the SPL.

Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Igor Grinberg <grinberg@compulab.co.il>
2017-05-08 11:38:38 -04:00
Uri Mashiach
ef3f3b8100 arm: usb: dra7xx: xHCI registers based on USB port index
Modify the determination of the base address of xHCI registers of DRA7XX
targets.
Before the commit: by the target.
After the commit: by the USB port index.

Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Roger Quadros <rogerq@ti.com>
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
2017-05-08 11:38:36 -04:00
Uri Mashiach
67566ab66b arm: dra7xx: move CONFIG_DRA7XX to Kconfig
The symbol CONFIG_DRA7XX is needed for Kconfig conditions.

Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-05-08 11:38:35 -04:00
xypron.glpk@gmx.de
cc93834dee meson: gxbb: increase CONFIG_SYS_BOOTM_LEN
A feature rich Linux kernel needs more than 8 MiB.
Hence enlarge CONFIG_SYS_BOOTM_LEN to 64 MiB for the GXBB systems.
As all known GXBB systems have at least 512 MiB of RAM this poses no problem.

Cc: Andreas Färber <afaerber@suse.de>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2017-05-05 16:45:52 -04:00
xypron.glpk@gmx.de
d03857485e meson: gxbb: change ramdisk_addr_r
0x10000000 is the start of a 2 MiB area used by the
ARM Trusted Firmware (BL31).

See
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable.git/tree/arch/arm64/boot/dts/amlogic/meson-gx.dtsi?id=refs/tags/v4.10.10

So we should not load the ramdisk here.

The legacy Ubuntu image for the Odroid C2 comes with the
following line in boot.ini:
setenv initrd_loadaddr "0x13000000"

See
http://odroid.in/ubuntu_16.04lts/ubuntu64-16.04-minimal-odroid-c2-20160815.img.xz
http://deb.odroid.in/c2/pool/main/u/u-boot/u-boot_20170226-752a100-8_arm64.deb

So let's use the same address.

With the patch booting Linux with booti succeeds on an Odroid C2,
without the patch Linux hangs.

Cc: Andreas Färber <afaerber@suse.de>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Vagrant Cascadian <vagrant@debian.org>
2017-05-01 12:38:17 -04:00
xypron.glpk@gmx.de
1f677e4266 meson: gxbb: enable MMC as boot target
To enable automatic booting from SD card or eMMC the MMC
devices 0, 1, and 2 are added to the BOOT_TARGET_DEVICES.

Booting from SD card, eMMC, and DHCP are tried in sequence.
A missing or failing device is gracefully handled.

Cc: Andreas Färber <afaerber@suse.de>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tested-by: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Tested-by: Andreas Färber <afaerber@suse.de>
2017-05-01 11:49:48 -04:00
Chris Packham
c9032ce168 cmd: add Kconfig option for 'date' command
Signed-off-by: Chris Packham <judge.packham@gmail.com>
[trini: default y if DM_RTC, re-sync]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-05-01 09:04:56 -04:00
Simon Glass
00aff7bbc3 powerpc: Drop configs/manroland
This is not used in U-Boot. Drop it.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-04-30 13:41:02 -04:00
Simon Glass
93d66ee566 Convert CONFIG_CMD_DISPLAY to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_DISPLAY

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-04-30 13:41:01 -04:00
Simon Glass
3bd25cb512 Convert CONFIG_CMD_DIAG to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_DIAG

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: imply CMD_DIAG on some keymile configs]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-04-30 13:41:01 -04:00
Simon Glass
10c01337d3 Kconfig: Drop CONFIG_CMD_DFL
This option is not used in U-Boot. Drop it.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-04-30 13:41:00 -04:00
Simon Glass
d569c95ec0 Convert CONFIG_CMD_DEKBLOB to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_DEKBLOB

Note: This option does not seem to actually be enabled by any board.

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: imply under SECURE_BOOT for mx5/6/7]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-04-30 13:41:00 -04:00
Simon Glass
279e7c491b Kconfig: Drop CONFIG_CMD_DEFAULTENV_VARS
This option does not exist in U-Boot. Drop it.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-04-30 13:41:00 -04:00
Simon Glass
9707274718 fs: Convert CONFIG_CMD_CRAMFS to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_CRAMFS

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: imply CMD_CRAMFS for keymile]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-04-30 13:40:59 -04:00
Simon Glass
d315628edb Convert CONFIG_CMD_CLK to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_CLK

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: imply CMD_CLK on ARCH_ZYNQ]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-04-30 13:40:58 -04:00
Simon Glass
3d0aeb9090 Drop CONFIG_CMD_CLEAR
This option is not used in U-Boot. Drop it.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-04-30 13:40:58 -04:00
Simon Glass
854fcd5537 Convert CONFIG_CMD_CHIP_CONFIG to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_CHIP_CONFIG

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-04-30 13:40:57 -04:00
Simon Glass
d66a10fc00 fs: Convert CONFIG_CMD_CBFS to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_CBFS

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: imply CMD_CBFS on SYS_COREBOOT]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-04-30 13:40:56 -04:00
Simon Glass
983b103f1c Convert CONFIG_SYS_WHITE_ON_BLACK to Kconfig
This converts the following to Kconfig:
   CONFIG_SYS_WHITE_ON_BLACK

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Make this default y on various SoCs]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-04-30 13:40:13 -04:00
Simon Glass
4893e34b00 Convert CONFIG_CMD_BSP to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_BSP

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-04-30 10:30:10 -04:00
Simon Glass
0f7102588c Convert CONFIG_CMD_BMP to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_BMP

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Add depends on LCD || DM_VIDEO || VIDEO]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-04-30 10:30:08 -04:00
Simon Glass
218257b01a Convert CONFIG_CMD_BMODE to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_BMODE

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Make this default y and depend on mx5/6/7]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-04-30 10:30:06 -04:00
Simon Glass
ac20a1b21c Convert CONFIG_CMD_BEDBUG to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_BEDBUG

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-04-30 10:30:02 -04:00
Simon Glass
ac60e46e7d Convert CONFIG_CMD_BAT to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_BAT

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-04-30 10:30:00 -04:00
Simon Glass
4848d89d1f ti816x_evm: Change CONFIG_CMD_ASKEN to CONFIG_CMD_ASKENV
This looks like a typo. Fix it.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-04-30 10:29:58 -04:00
Simon Glass
b1a873df0a Convert CONFIG_CMD_AES et al to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_AES
   CONFIG_AES

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Add select AES to CMD_AES]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-04-30 10:29:55 -04:00
Simon Glass
92572ecf80 power: Drop CONFIG_PMIC
This option is not used in U-Boot. Drop it.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-04-30 10:29:54 -04:00
Simon Glass
0fd28b1f0e power: Drop CONFIG_I2C_PMIC
This is only used by one board and should not be a CONFIG option. Instead
it should use the driver model pmic framework. For now, just move the
setting into the only board that uses it.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-04-30 10:29:53 -04:00
Simon Glass
bdf25a5e04 power: Convert CONFIG_PMIC_AS3722 to Kconfig
This converts the following to Kconfig:
   CONFIG_PMIC_AS3722

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-04-30 10:29:50 -04:00
Simon Glass
56aceaf282 power: Rename CONFIG_AS3722_POWER to CONFIG_PMIC_AS3722
Before converting this to Kconfig, rename it to match the other PMICs.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-04-30 10:29:47 -04:00
Tom Rini
29ec685883 arm: Re-sync ARCH_MX5 / MX51 / MX53 CONFIG options
A few boards had not been fully re-synced with CONFIG_ARCH_MX5 / CONFIG_MX51 /
CONFIG_MX53 being in Kconfig.  Do so now.

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-04-30 10:29:38 -04:00
Jernej Skrabec
56009451d8 sunxi: video: Add A64/H3/H5 HDMI driver
This commit adds support for HDMI output.

Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-04-28 09:21:25 +02:00
Jernej Skrabec
a8f01ccff2 sunxi: i2c: Add support for DM I2C
This commit adds support for DM I2C on sunxi platform. It can coexist
with old style sunxi I2C driver, because it is still used in SPL and
by some SoCs.

Because sunxi platform doesn't yet support DM clk, reset and pinctrl
driver, workaround is needed to enable clocks and set resets and
pinctrls. This is done by calling i2c_init_board() in board_init().
This means that CONFIG_I2Cx_ENABLE options needs to be correctly set
in order to use needed I2C controller.

Commit is based on the previous patch made by Philipp Tomsich

Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-04-28 09:19:03 +02:00
Masahiro Yamada
a93fbf4a78 ARM: omap2+: rename config to ARCH_OMAP2PLUS and consolidate Kconfig
In Linux, CONFIG_ARCH_OMAP2PLUS is used for OMAP2 or later SoCs.
Rename CONFIG_ARCH_OMAP2 to CONFIG_ARCH_OMAP2PLUS to follow this
naming.

Move the OMAP2+ board/SoC choice down to mach-omap2/Kconfig to slim
down the arch/arm/Kconfig level.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-04-27 16:49:08 -04:00
Alexey Brodkin
a1b343d754 clean-up: Remove uselsess mentions of CONFIG_COMMAND_HISTORY
These were reminders that somehow slipped through the cracks
or were erroneously introduced after previous clean-ups.

Getting rid of then once again. Hopefully for good now :)

Where missing and appropriate replace with CONFIG_CMDLINE_EDITING
which really enables shell history as of now.

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Peter Griffin <peter.griffin@linaro.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Steve Rae <steve.rae@raedomain.com>
Cc: Jon Mason <jon.mason@broadcom.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-04-27 16:49:03 -04:00
Tom Rini
6f008a2e16 Merge git://git.denx.de/u-boot-sunxi 2017-04-25 16:12:42 -04:00
Tom Rini
9ad99bee9c Merge branch 'master' of git://git.denx.de/u-boot-socfpga 2017-04-25 08:59:56 -04:00
Dalon Westergreen
6bd041f00d arm: socfpga: add cyclone5 based de10-nano board
Add support for the Terasic DE10-Nano board.  The board
is based on the DE0-Nano-Soc board but adds a larger FPGA
and an HDMI output.

Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
Reviewed-by: Dinh Nguyen <dinguyen@kernel.org>
2017-04-25 12:46:44 +02:00
Tom Rini
9a1d64809d Merge branch 'master' of git://git.denx.de/u-boot-mips 2017-04-24 21:08:10 -04:00
Andreas Färber
2eff3b7179 sunxi: Fix arm64 fdtfile variable
Currently $fdtfile is constructed from CONFIG_DEFAULT_TREE, containing
the filename. However on arm64 that file is located in an allwinner
subdirectory.

To avoid the need for users/distros symlinking the .dtb files, prepend
the vendor directory for ARM64.

This aligns Pine64 with other boards such as Raspberry Pi 3.

Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-04-24 11:55:42 +05:30
Kyle Edwards
1967228b02 mips: qemu-mips/64: Expand malloc pool for CONFIG_SYS_BOOTPARAMS_LEN
Before this patch, CONFIG_SYS_BOOTPARAMS_LEN was the same size as
CONFIG_SYS_MALLOC_LEN. So, if malloc() had previously been called, and
initr_malloc_bootparams() was called, it would fail with an out-of-
memory error. This patch fixes this issue by expanding the malloc pool
to 256KB.

Signed-off-by: Kyle Edwards <kyleedwardsny@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2017-04-21 13:54:47 +02:00
Kyle Edwards
9828d050cf mips: qemu-mips/64: Remove obsolete CONFIG_SYS_MONITOR_LEN from config
This fixes an issue with the saveenv command causing U-Boot to no
longer work on the QEMU Mips pseudoboard. Because the offset of the
environment was being determined by CONFIG_SYS_MONITOR_LEN, and this
value was less than the actual size of U-Boot, saveenv was overwriting
parts of the U-Boot code. Because CONFIG_SYS_MONITOR_LEN is no longer
used on MIPS, this patch removes it and places the environment at the
end of the pseudoboard's 4MB flash.

Signed-off-by: Kyle Edwards <kyleedwardsny@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2017-04-21 13:54:47 +02:00
Icenowy Zheng
e267d94011 sunxi: add DTSI file for V3s
As we have now V3s support in board code, the V3s DTSI file should also
be added.

Add also some CCU include headers to satisfy the DTSI file.

Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-04-21 09:23:27 +02:00
Icenowy Zheng
c199489f17 sunxi: add basic V3s support
Basic U-Boot support is now present for V3s.

Some memory addresses are changed specially for V3s, as the original
address map cannot fit into a so small DRAM.

As the DRAM controller code needs a big refactor, the SPL support is
disabled in this version.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-04-21 09:23:17 +02:00
Mylène Josserand
7095f86418 sunxi: Convert CONS_INDEX to Kconfig
Convert the CONS_INDEX configuration to Kconfig.
Update sunxi's defconfigs to remove SYS_EXTRA_OPTIONS variable not
needed anymore.
Default value is 1 except for sun5i (equals 2) and sun8i (equals 5).

Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
[Maxime: Added a depends on ARCH_SUNXI to avoid build breakages]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-04-20 13:20:32 +02:00
Tom Rini
3c476d841d Merge git://git.denx.de/u-boot-fsl-qoriq 2017-04-18 11:36:06 -04:00
Masahiro Yamada
573a3811ed sysreset: psci: support system reset in a generic way with PSCI
If the system is running PSCI firmware, the System Reset function
(func ID: 0x80000009) is supposed to be handled by PSCI, that is,
the SoC/board specific reset implementation should be moved to PSCI.
U-Boot should call the PSCI service according to the arm-smccc
manner.

The arm-smccc is supported on ARMv7 or later.  Especially, ARMv8
generation SoCs are likely to run ARM Trusted Firmware BL31.  In
this case, U-Boot is a non-secure world boot loader, so it should
not be able to reset the system directly.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-04-18 10:29:19 -04:00
Masahiro Yamada
c54bcf6805 ARM: adjust arm-smccc code for use in U-Boot
Adjust ARM SMC Calling Convention code for U-Boot:
  - Replace the license block with SPDX
  - Change path to asm-offsets.h
  - Define UNWIND() as no-op
  - Add Kconfig entry
  - Add asm-offsets

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-04-18 10:29:17 -04:00
Masahiro Yamada
c2da86f39e ARM: import arm-smccc code from Linux 4.11-rc6
Imports ARM SMC Calling Convention code from Linux 4.11-rc6.
The files have been copied as follows:

[Linux]                           [U-Boot]
arch/arm/kernel/smccc-call.S   -> arch/arm/cpu/armv7/smccc-call.S
arch/arm64/kernel/smccc-call.S -> arch/arm/cpu/armv8/smccc-call.S
arch/arm/include/asm/opcodes*  -> arch/arm/include/asm/opcodes*
include/linux/arm-smccc.h      -> include/linux/arm-smccc.h

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-04-18 10:29:16 -04:00
York Sun
73fb583829 armv7: ls1021a: Drop macro CONFIG_LS102XA
Use CONFIG_ARCH_LS1021A instead.

Signed-off-by: York Sun <york.sun@nxp.com>
2017-04-17 09:03:30 -07:00
York Sun
c1303bfd7e armv8: ls1043a: Drop macro CONFIG_LS1043A
Use CONFIG_ARCH_LS1043A instead.

Signed-off-by: York Sun <york.sun@nxp.com>
2017-04-17 09:03:30 -07:00
York Sun
4a3ab19322 armv8: ls2080a: Drop macro CONFIG_LS2080A
Use CONFIG_ARCH_LS2080A instead.

Signed-off-by: York Sun <york.sun@nxp.com>
2017-04-17 09:03:30 -07:00
Ruchika Gupta
511fc86d0b arm: ls1046ardb: Add SD secure boot target
- Add SD secure boot target for ls1046ardb.
- Change the u-boot size defined by a macro for copying the main
  U-Boot by SPL to also include the u-boot Secure Boot header size
  as header is appended to u-boot image. So header will also be
  copied from SD to DDR.
- CONFIG_MAX_SPL_SIZE is limited to 90KB. SPL is copied to OCRAM
  (128K) where 32K are reserved for use by boot ROM and 6K for the
  header.
- Reduce the size of CAAM driver for SPL Blobification functions
  and descriptors, that are not required at the time of SPL are
  disabled. Further error code conversion to strings is disabled
  for SPL build.

Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-04-17 09:03:30 -07:00
Ruchika Gupta
762f92a60e arm: ls1043ardb: Add NAND secure boot target
Add NAND secure boot target for ls1043ardb.

- Change the u-boot size defined by a macro for copying the main
  U-Boot by SPL to also include the u-boot Secure Boot header size as
  header is appended to u-boot image. So header will also be copied
  from SD to DDR.
- MACRO for CONFIG_BOOTSCRIPT_COPY_RAM is enabled to copy Bootscript
  from NAND to DDR. Offsets for Bootscript on NAND and DDR have been
  also defined.

Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-04-17 09:03:30 -07:00
Ruchika Gupta
70f9661ca9 arm: ls1043ardb: Add SD secure boot target
- Add SD secure boot target for ls1043ardb.
- Implement FSL_LSCH2 specific spl_board_init() to setup CAAM stream
  ID and corresponding stream ID in SMMU.
- Change the u-boot size defined by a macro for copying the main
  U-Boot by SPL to also include the u-boot Secure Boot header size as
  header is appended to u-boot image. So header will also be copied
  from SD to DDR.
- CONFIG_MAX_SPL_SIZE is limited to 90KB. SPL is copied to OCRAM
  (128K) where 32K are reserved for use by boot ROM and 6K for secure
  boto header.
- Error messages during SPL boot are limited to error code numbers
  instead of strings to reduce the size of SPL image.

Signed-off-by: Vinitha Pillai-B57223 <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-04-17 09:03:30 -07:00
Vinitha Pillai-B57223
11d14bfb75 armv8: LS1012ARDB: Add QSPI Secure Boot target
Add QSPI Secure Boot target to enable chain of trust

Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Reviewed-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-04-17 09:03:30 -07:00
Vinitha Pillai-B57223
f7244f2c48 armv8: LS1046ARDB: Add QSPI Secure Boot target
Add QSPI Secure Boot target. Also enable sec init.

Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-04-17 09:03:30 -07:00
Sumit Garg
a52ff334c5 armv8: ls1046ardb: SPL size reduction
Using changes in this patch we were able to reduce approx 4k
size of u-boot-spl.bin image. Following is breif description of
changes to reduce SPL size:
1. Changes in board/freescale/ls1046ardb/Makefile to remove
   compilation of eth.c and cpld.c in case of SPL build.
2. Changes in board/freescale/ls1046ardb/ls1046ardb.c to keep
   only ddr_init and board_early_init_f funcations in case of SPL
   build.
3. Changes in ls1046a_common.h & ls1046ardb.h to remove driver
   specific macros due to which static data was being compiled in
   case of SPL build.
4. Disable MMC driver from bieng compiled in case of SPL NAND
   build and NAND driver from bieng compiled in case of SPL MMC build.

Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-04-17 09:03:30 -07:00
Sumit Garg
4139b17037 armv8: ls1043ardb: SPL size reduction
Using changes in this patch we were able to reduce approx 10k
size of u-boot-spl.bin image. Following is breif description of
changes to reduce SPL size:
1. Changes in board/freescale/ls1043ardb/Makefile to remove
   compilation of eth.c and cpld.c in case of SPL build.
2. Changes in board/freescale/ls1043ardb/ls1043ardb.c to keep
   only ddr_init and board_early_init_f funcations in case of SPL
   build.
3. Changes in ls1043a_common.h & ls1043ardb.h to remove driver
   specific macros due to which static data was being compiled in
   case of SPL build.
4. Disable MMC driver from bieng compiled in case of SPL NAND
   build and NAND driver from bieng compiled in case of SPL MMC build.
5. Remove I2C driver support from SPL in case of LS1043ARDB.

Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-04-17 09:03:30 -07:00
Tom Rini
af8ef2ed21 Merge git://git.denx.de/u-boot-rockchip 2017-04-16 22:08:13 -04:00
Tom Rini
51f866e8da Merge git://git.denx.de/u-boot-dm 2017-04-16 22:07:52 -04:00
Klaus Goger
a13110a99f rockchip: ARM64: split RK3399-Q7 board off the RK3399-EVB board
The RK3399-Q7 SoM is a Qseven-compatible (70mm x 70mm, MXM-230
connector) system-on-module from Theobroma Systems, featuring the
Rockchip RK3399.

It provides the following feature set:
 * up to 4GB DDR3
 * on-module SPI-NOR flash
 * on-module eMMC (with 8-bit interace)
 * SD card (on a baseboad) via edge connector
 * Gigabit Ethernet w/ on-module Micrel KSZ9031 GbE PHY
 * HDMI/eDP/MIPI displays
 * 2x MIPI-CSI
 * USB
   - 1x USB 3.0 dual-role (direct connection)
   - 2x USB 3.0 host + 1x USB 2.0 (on-module USB 3.0 hub)
 * on-module STM32 Cortex-M0 companion controller, implementing:
   - low-power RTC functionality (ISL1208 emulation)
   - fan controller (AMC6821 emulation)
   - USB<->CAN bridge controller

Note that we use a multi-payload FIT image for booting and have
Cortex-M0 payload in a separate subimage: we thus rely on the FIT
image loader to put it into the SRAM region that ATF expects it in.

Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Fixed build warning on puma-rk3399:
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-04-15 10:13:17 -06:00
Kever Yang
86d012657c rockchip: rk3399: do not use lower address
The lower address is reserved for ATF, do not use it.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
2017-04-15 10:13:17 -06:00
Eddie Cai
1e9d6c159f rockchip: Add USB to the default boot targets
Now that most rockchip SoC based board have usb host support, enable
USB boot targets by default.

Signed-off-by: Eddie Cai <eddie.cai.linux@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Fixed build errors when CONFIG_CMD_USB not defined:
Signed-off-by: Simon Glass <sjg@chromium.org>
2017-04-15 10:13:17 -06:00
Eddie Cai
bfc664ba8b rockchip: tinker: configs: Add USB, PXE, DHCP to the default boot targets
tinker board support ethernet and usb host, so enable USB, PXE and DHCP support.

Signed-off-by: Eddie Cai <eddie.cai.linux@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2017-04-15 10:13:17 -06:00
Wenyou Yang
1878804a2b board: sama5d3_xplained: Update to support DM/DT
Update the configuration files to support the device tree and driver
model, so do SPL. The device clock and pins configuration are handled
by the clock and the pinctrl drivers respectively.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Fix build error with sama5d3_xplained_mmc:
Signed-off-by: Simon Glass <sjg@chromium.org>
2017-04-14 20:10:35 -06:00
Wenyou Yang
b6ceefedf7 board: sama5d3xek: Clean up code
Due to the introduction of the pinctrl and clk driver, and using
device tree files, remove the unneeded hardcoded pin configuration
and clock enabling code from the board file.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Remove CONFIG_PHY_MICREL as per previous patch:
Signed-off-by: Simon Glass <sjg@chromium.org>
2017-04-14 20:10:25 -06:00
Wenyou Yang
a97cb06154 board: sama5d3xek: Update to support DM/DT
Update the configuration files to support the device tree and
driver model, so do SPL. The device clock and pins configuration
are handled by the clock and the pinctrl drivers respectively.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Add back CONFIG_PHY_MICREL to prevent a build error:
Signed-off-by: Simon Glass <sjg@chromium.org>
2017-04-14 20:09:28 -06:00
Tom Rini
3fea953698 Merge branch 'master' of git://git.denx.de/u-boot-video 2017-04-14 22:05:17 -04:00
Simon Glass
53378dac8d dm: led: Add support for blinking LEDs
Allow LEDs to be blinked if the driver supports it. Enable this for
sandbox so that the tests run.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ziping Chen <techping.chan@gmail.com>
2017-04-14 19:38:57 -06:00
Simon Glass
9413ad4f0d dm: led: Support toggling LEDs
Add support for toggling an LED into the uclass interface. This can be
efficiently implemented by the driver.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ziping Chen <techping.chan@gmail.com>
2017-04-14 19:38:57 -06:00
Simon Glass
8f4b612333 dm: led: Add support for getting the state of an LED
It is useful to be able to read the LED as well as write it. Add this to
the uclass and update the GPIO driver.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ziping Chen <techping.chan@gmail.com>
2017-04-14 19:38:57 -06:00
Simon Glass
ddae9fcddc dm: led: Adjust the LED uclass
At present this is very simple, supporting only on and off. We want to
also support toggling and blinking. As a first step, change the name of
the main method and use an enum to indicate the state.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ziping Chen <techping.chan@gmail.com>
2017-04-14 19:38:57 -06:00
Simon Glass
56e19871dc dm: led: Rename struct led_uclass_plat
These structures are normally named with 'uc' instead of 'uclass'. Change
this one for consistency.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ziping Chen <techping.chan@gmail.com>
2017-04-14 19:38:57 -06:00
Tom Rini
c1a16c3ab5 Merge branch 'master' of git://git.denx.de/u-boot-socfpga 2017-04-14 09:05:57 -04:00
Tom Rini
af1b7286d8 Merge branch 'master' of git://git.denx.de/u-boot-mmc 2017-04-14 09:05:46 -04:00
Dalon Westergreen
09397d99ed arm: socfpga: sr1500 use environment in common header
This removes the default environment from the sr1500 header
and instead uses the common environment provided in
socfpga_common.h which now uses distro boot.

This board has no upstream devicetree in the kernel source,
so set to socfpga_cyclone5_sr1500.dtb.

Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>

--
Changes in v2:
 - Remove unneeded CONFIG_BOOTFILE
 - set devicetree name to match socfpga_{fpga model}_{board model}.dts
   pattern
2017-04-14 14:07:13 +02:00
Dalon Westergreen
19a8fed57c arm: socfpga: Socrates use environment in common header
This removes the default environment from the socrates headers
and instead uses the common environment provided in
socfpga_common.h which now uses distro boot.

Change default devicetree name to match devicetree name in
upstream kernel source.

Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>

--
Changes in v2:
 - Remove unneeded CONFIG_BOOTFILE
2017-04-14 14:07:11 +02:00
Dalon Westergreen
b52acd8f97 arm: socfpga: SoCKit use environment in common header
This removes the default environment from the SoCKit headers
and instead uses the common environment provided in
socfpga_common.h which now uses distro boot.

Change default devicetree name to match devicetree name in
upstream kernel source.

Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>

--
Changes in v2:
 - Remove unneeded CONFIG_BOOTFILE
2017-04-14 14:07:09 +02:00
Dalon Westergreen
9e41d225ca arm: socfpga: DE1 use environment in common header
This removes the default environment from the de1 headers
and instead uses the common environment provided in
socfpga_common.h which now uses distro boot.

This board does not have a devicetree in the upstream kernel
source so set devicetree to socfpga_cyclone5_de1_soc.dtb.

Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>

--
Changes in V2:
 - Remove unneeded CONFIG_BOOTFILE
 - set devicetree name to match socfpga_{fpga model}_{board model}.dts
   pattern
2017-04-14 14:07:07 +02:00
Dalon Westergreen
5e7ae1afb2 arm: socfpga: C5 SoCDK use environment in common header
This removes the default environment from the C5 SoCDK headers
and instead uses the common environment provided in
socfpga_common.h which now uses distro boot.

In addition to the above, add support to boot from the custom
a2 type partition.

Change default devicetree name to match devicetree name in
upstream kernel source.

Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>

--
Changes in v2:
 - Remove unneeded CONFIG_BOOTFILE
2017-04-14 14:07:05 +02:00
Dalon Westergreen
57b6b62f56 arm: socfpga: A5 SoCDK use environment in common header
This removes the default environment from the A5 socdk headers
and instead uses the common environment provided in
socfpga_common.h which now uses distro boot.

Add support to boot from the custom a2 type partition.

Change default devicetree name to match devicetree name in
upstream kernel source.

Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>

--
Changes in v3:
 - Fix small typo in defconfig, missing "C"
Changes in v2:
 - Remove unneeded CONFIG_BOOTFILE
 - Fix dtb name

a5config test

Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
2017-04-14 14:07:03 +02:00
Dalon Westergreen
29c0655173 arm: socfpga: DE0 use environment in common header
This removes the default environment from the de0 headers
and instead uses the common environment provided in
socfpga_common.h which now uses distro boot.

In addition to the above, add support to boot from the custom
a2 type partition

Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>

--
Changes in v2:
 - Remove unneeded CONFIG_BOOTFILE
2017-04-14 14:07:01 +02:00
Dalon Westergreen
451e824125 arm: socfpga: Add distro boot to socfpga common header
This adds a common environment and support for distro boot
in the common socfpga header.

Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>

--
Changes in v5:
 - Per Frank, to support OpenSuse the ENV must be after the GPT
Changes in v4:
 - Move env back to being right after the MBR
Changes in v3:
 - fix spacing between asterix
 - remove verify=n as a default setting

Changes in v2:
 - Remove unneeded CONFIG_BOOTFILE and fdt_addr
 - cleanup spacing in MMC env size

common

Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
2017-04-14 14:06:59 +02:00
Ley Foon Tan
707cd012e2 arm: socfpga: Convert Altera DDR SDRAM driver to use Kconfig
Convert Altera DDR SDRAM driver to use Kconfig method.
Enable ALTERA_SDRAM by default if it is on Gen5 target.
Arria 10 will have different driver.

Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2017-04-14 14:06:57 +02:00
Ley Foon Tan
e11b5e8d6e fdt: Add compatible strings for Arria 10
Add compatible strings for Intel Arria 10 SoCFPGA device.

Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2017-04-14 14:06:55 +02:00
Marek Vasut
d70b338ec6 ARM: socfpga: mcvevk: Add default dfu_alt_info
Add default DFU altinfo for eMMC.

Signed-off-by: Marek Vasut <marex@denx.de>
2017-04-14 14:06:52 +02:00
Marek Vasut
55ce55faaa ARM: socfpga: Reduce the DFU buffer size
There is no point in having such gargantuan buffer, it only requires
huge malloc area. Reduce the DFU buffer size.

Signed-off-by: Marek Vasut <marex@denx.de>
2017-04-14 14:06:49 +02:00
Marek Vasut
a548bc511f ARM: socfpga: Rename MCVEVK
The board is now manufactured by Aries Embedded GmbH , rename it.

Signed-off-by: Marek Vasut <marex@denx.de>
2017-04-14 14:06:44 +02:00
Stefan Agner
80b9c3bb80 board: toradex: colibri_vf: Add DCU support for Colibri Vybrid
The Vybrid SoC family has the same display controller unit (DCU)
like the LS1021A SoC. This patch adds platform data, pinmux defines
and clock control to enable the driver for Toradex Colibri Vybrid
module.

Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2017-04-14 14:03:07 +02:00
Stefan Agner
77810e638e video: fsl_dcu_fb: fix framebuffer to the end of memory
Fix the framebuffer location to the very end of the available memory.
This allows to remove the area from available memory for the kernel,
which in turn allows to display the splash screen through the Linux
kernel boot process.

Ideas has been taken from the sunxi display driver, e.g.
20779ec3a5 ("sunxi: video: Dynamically reserve framebuffer memory")

Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
2017-04-14 13:50:41 +02:00
Sanchayan Maity
b215fb3f34 Convert CONFIG_FSL_DCU_FB to Kconfig
Rename CONFIG_FSL_DCU_FB to CONFIG_VIDEO_FSL_DCU_FB
and convert it to Kconfig.

Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Reviewed-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Alison Wang <alison.wang@nxp.com>
2017-04-14 13:37:35 +02:00
Heiner Kallweit
a3b02a1d49 arm: dts: update Meson GXBB / Odroid-C2 DT with recent Linux version
As a prerequisite for adding a Meson GX MMC driver update the
Meson GXBB / Odroid-C2 device tree in Uboot with the latest
version from Linux.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
2017-04-14 15:16:06 +09:00
Tom Rini
b7b24a7a3c Merge git://git.denx.de/u-boot-dm
Here with some DM changes as well as the long-standing AT91 DM/DT
conversion patches which I have picked up via dm.
2017-04-13 17:31:06 -04:00
Wenyou Yang
ef33aa3dca board: sama5d4ek: update to support DM/DT
Update the configuration files to support the device tree and driver
model, so do SPL. The device clock and pins configuration are handled
by the clock and the pinctrl drivers respectively.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
2017-04-13 14:44:52 -06:00
Wenyou Yang
6dbadb4d95 board: sama5d4_xplained: update to support DM/DT
Update the configuration files to support the device tree and
driver model, so do SPL. The device clock and pins configuration
are handled by the clock and the pinctrl drivers respectively.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
2017-04-13 14:44:52 -06:00
Wenyou Yang
fc977b94a4 configs: at91-sama5_common: fix for CONFIG_AT91_GPIO
Add #ifndef CONFIG_DM_GPIO for CONFIG_AT91_GPIO define to avoid
the redefine compilation error.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
2017-04-13 14:44:52 -06:00
Wenyou Yang
9319a756ff pinctrl: at91: add pinctrl driver
AT91 PIO controller is a combined gpio-controller, pin-mux and
pin-config module. The peripheral's pins are assigned through
per-pin based muxing logic.

Each SoC will have to describe the its limitation and pin
configuration via device tree. This will allow to do not need
to touch the C code when adding new SoC if the IP version is
supported.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-04-13 14:44:50 -06:00
Tom Rini
1622559066 Merge branch 'master' of git://www.denx.de/git/u-boot-imx
Drop CONFIG_STACKSIZE from include/configs/imx6_logic.h

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-04-13 11:19:00 -04:00
Peng Fan
0342e335ba lib: div64: sync with Linux
Sync with Linux commit ad0376eb1483b ("Merge tag 'edac_for_4.11_2'").

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Tom Rini <trini@konsulko.com>
2017-04-13 09:41:10 -04:00
Tom Rini
6823e6fe66 sandbox: Change CONFIG_SANDBOX_BITS_PER_LONG to hard-coded
Instead of having CONFIG_SANDBOX_BITS_PER_LONG in sandbox.h set to 64
with a comment to change to 32 on a 32bit host, simply set this to 64 in
asm/types.h and have the comment be there.

Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-04-13 09:41:09 -04:00
Simon Glass
f1683aa73c board_f: Rename initdram() to dram_init()
This allows us to use the same DRAM init function on all archs. Add a
dummy function for arc, which does not use DRAM init here.

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Dummy function on nios2]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-04-13 09:40:57 -04:00
Simon Glass
3eace37e50 arm: freescale: Rename initdram() to fsl_initdram()
This function name shadows a global name but is in fact different. This
is very confusing. Rename it to help with the following refactoring.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-04-12 13:28:32 -04:00
tim.chick
6bacc73621 debug_uart: Try not to use stack in printch
Spam detection software, running on the system "lists.denx.de",
has identified this incoming email as possible spam.  The original
message has been attached to this so you can view it or label
similar future email.  If you have any questions, see
@@CONTACT_ADDRESS@@ for details.

Content preview:  Previous change to create _printch causes the stack to be
  used, breaking printch before stack is available. Inline _printch to prevent
   this happening. Signed-off-by: Tim Chick <tim.chick@mediatek.com> --- [...]

Content analysis details:   (6.3 points, 5.0 required)

 pts rule name              description
---- ---------------------- --------------------------------------------------
 0.7 RCVD_IN_XBL            RBL: Received via a relay in Spamhaus XBL
                            [188.29.165.105 listed in zen.spamhaus.org]
 3.6 RCVD_IN_PBL            RBL: Received via a relay in Spamhaus PBL
 1.6 RCVD_IN_BRBL_LASTEXT   RBL: No description available.
                            [188.29.165.105 listed in bb.barracudacentral.org]
 0.4 RDNS_DYNAMIC           Delivered to internal network by host with
                            dynamic-looking rDNS
Previous change to create _printch causes the stack to be used,
breaking printch before stack is available. Inline _printch to
prevent this happening.

Signed-off-by: Tim Chick <tim.chick@mediatek.com>
2017-04-12 13:28:30 -04:00
Stefano Babic
b80c0b9934 Rename aes.h to uboot_aes.h
aes.h is a too generic name if this file can
be exported and used by a program.
Rename it to avoid any conflicts with
other files (for example, from openSSL).

Signed-off-by: Stefano Babic <sbabic@denx.de>
2017-04-12 13:28:27 -04:00
Adam Ford
f479cec3b6 imx: i.mx6q: add the initial support for LogicPD i.MX6Q SOM
Logic PD has an i.MX6Q system on module (SOM) with a development kit. The
SOM has a built-in microSD socket, DDR and NAND flash.  The development kit
has an SMSC Ethernet PHY, serial debug port and a variety of peripherals.
This have been verified to boot the i.MX6Q version over either SD
on the development kit or NAND built into the SOM.  Items in the dtsi file
are specific to the SOM itself.  Items in the dts file are in the baseboard.
Future versions of the SOM will come out supporting the same basebord and
potentially future base boards will come out supporting the same SOM.

Signed-off-by: Adam Ford <aford173@gmail.com>
2017-04-12 18:59:12 +02:00
Tim Harvey
b69999efd8 imx: ventana: config: set MMC env Partition to 1
Partition 1 equates to EMMC boot0

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2017-04-12 18:24:04 +02:00
Vagrant Cascadian
52526ba42e Set console speed to 115200 on mx6cuboxi.
By default, u-boot itself outputs on the serial console at 115200, so
it may as well pass the same value to the booted operating system as
well.

Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-04-12 18:09:32 +02:00
Yung-Ching LIN
f6f7e73d45 board: advantech: dms-ba16: Add the configuration options for display initialization
Add the configuration options for display initialization in case we need to
do the display initialization in kernel to support different timing settings

Signed-off-by: Ken Lin <yungching0725@gmail.com>
Acked-by: Akshay Bhat <akshay.bhat@timesys.com>
2017-04-12 18:04:33 +02:00
Lukasz Majewski
5b8299e320 MCCMON6: defconfig: Add tftp_nor_dtb command for NOR DTB update
Signed-off-by: Lukasz Majewski <lukma@denx.de>
2017-04-12 17:48:45 +02:00
Tom Rini
01cce5fdd0 Merge git://git.denx.de/u-boot-x86 2017-04-10 08:07:29 -04:00
Bin Meng
d24c7fbcc5 dm: rtc: Add 16-bit read/write support
At present there are only 8-bit and 32-bit read/write routines in
the rtc uclass driver. This adds the 16-bit support.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-04-10 10:02:03 +08:00
Andy Shevchenko
c04cf0a571 x86: Remove unused option
There is option which is not used:
	CONFIG_ZBOOT_32

Remove it from default x86 config and from whitelist.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2017-04-10 10:02:03 +08:00
Madan Srinivas
a5c7e41be3 image: Fixes build warning with CONFIG_FIT_IMAGE_POST_PROCESS
The function 'board_fit_image_post_process' is defined only when the
config option CONFIG_FIT_IMAGE_POST_PROCESS is enabled. For secure
systems that do not use SPL but do use FIT kernel images, only
CONFIG_FIT_IMAGE_POST_PROCESS will be defined, which will result in an
implicit declaration of function 'board_fit_image_post_process' warning
while building u-boot. Fix this warning.

Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-04-08 21:35:04 -04:00
Andrew F. Davis
f7c8f032f4 ti_armv7_common: env: Change FIT image name to match build name
The most common name for a FIT image containing a bootable kernel is
"fitImage", as our builds now use this name also, change this to the
default in our U-Boot environment.

Signed-off-by: Andrew F. Davis <afd@ti.com>
2017-04-08 21:35:03 -04:00
Sekhar Nori
1120dda8cc davinci: omapl138_lcdk: switch to using common mmc args
Now that we have common MMC/SD boot environment
variables that can be used across TI platforms,
switch OMAP-L138 LCDK to use them.

As a nice side-effect, we get support for using
uEnv.txt on this platform.

Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-04-08 21:33:12 -04:00
Sekhar Nori
88fdfcd21d ARM: ti: consolidate mmc environment variables
Introduce include/environment/ti/mmc.h that
consolidates environment variable definitions
for various TI boards that support MMC/SD.

This allows reuse of same environment variables
on non-ARMv7 TI platforms like OMAP-L138 for
example.

While at it, move DFU-related environment variable
includes to only non-SPL builds for AM335x and
AM437x since they are not really used for SPL
today.

Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-04-08 21:33:12 -04:00
Sekhar Nori
6e8069616e davinci: omapl138_lcdk: use environment variables for memory addresses
Use environment variables for various memory addresses
used on OMAP-L138 LCDK board. This makes it easy to
customize the boot process.

Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-04-08 21:32:50 -04:00
Sekhar Nori
4c8865a239 davinci: omapl138_lcdk: remove spiboot
OMAP-L138 LCDK board does not have a SPI flash.
Remove spiboot related environment variable
definitions.

Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-04-08 21:32:49 -04:00
Tom Rini
089795090a Merge branch 'master' of git://git.denx.de/u-boot-sunxi 2017-04-08 09:28:02 -04:00
Alexandru Gagniuc
306b236bc1 common/xyzModem.c: unifdef (Remove useless #ifdefs)
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
2017-04-08 09:26:54 -04:00
robertcnelson@gmail.com
52609d753b config: am335x_evm: detect BeagleBone Blue using BLA
BeagleBone Blue is next grenation of boards from BeagleBoard.org, focusing
on robotics with a TI wl1835 wireless module for connectivity.

This board can be indentified by the BLAx value after A335BNLT (BBB)
in the at24 eeprom:
BLAx: [aa 55 33 ee 41 33 33 35  42 4e 4c 54 42 4c 41 30 |.U3.A335BNLTBLA2|]

http://beagleboard.org/blue
https://github.com/beagleboard/beaglebone-blue

firmware: https://github.com/beagleboard/beaglebone-black-wireless/tree/master/firmware
wl18xx mac address: /proc/device-tree/ocp/ethernet@4a100000/slave@4a100200/mac-address

Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
CC: Tom Rini <trini@konsulko.com>
CC: Jason Kridner <jkridner@beagleboard.org>
CC: Will Newton <willn@resin.io>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-04-08 09:26:52 -04:00
robertcnelson@gmail.com
2b79fba691 config: am335x_evm: detect Green Wireless using GW1
SeeedStudio BeagleBone Green Wireless (BBGW) is an expansion of the
SeeedStudio Green (BBG) with the Ethernet replaced by a TI wl1835
wireless module.

This board can be indentified by the GW1x value after A335BNLT (BBB)
in the at24 eeprom:
GW1x [aa 55 33 ee 41 33 33 35  42 4e 4c 54 47 57 31 41  |.U3.A335BNLTGW1A|]

http://beagleboard.org/green-wireless
http://wiki.seeed.cc/BeagleBone_Green_Wireless/

firmware: https://github.com/beagleboard/beaglebone-black-wireless/tree/master/firmware
wl18xx mac address: Stored in at24 eeprom at address 5-16:
hexdump -e '8/1 "%c"' /sys/bus/i2c/devices/0-0050/eeprom | cut -b 5-16

Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
CC: Tom Rini <trini@konsulko.com>
CC: Jason Kridner <jkridner@beagleboard.org>
CC: Will Newton <willn@resin.io>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-04-08 09:26:52 -04:00
robertcnelson@gmail.com
4015949f1f config: am335x_evm: detect Black Wireless using BWA
BeagleBone Black Wireless is clone of the BeagleBone Black (BBB) with
the Ethernet replaced by a TI wl1835 wireless module.

This board can be indentified by the BWAx value after A335BNLT (BBB)
in the at24 eeprom:
BWAx [aa 55 33 ee 41 33 33 35  42 4e 4c 54 42 57 41 35  |.U3.A335BNLTBWA5|]

http://beagleboard.org/black-wireless
https://github.com/beagleboard/beaglebone-black-wireless

firmware: https://github.com/beagleboard/beaglebone-black-wireless/tree/master/firmware
wl18xx mac address: /proc/device-tree/ocp/ethernet@4a100000/slave@4a100200/mac-address

Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
CC: Tom Rini <trini@konsulko.com>
CC: Jason Kridner <jkridner@beagleboard.org>
CC: Will Newton <willn@resin.io>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-04-08 09:26:51 -04:00
Vikas Manocha
dc11d83a2e stm32f7: enable instruction & data cache
It also enables commands for cache enable/disable/status.

Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
2017-04-08 09:26:51 -04:00
Andrew F. Davis
5bb7318f9c ti_armv7_common: env: Use args_mmc in FIT loading path
The env command 'args_fit' does not define a root path, this forces us to
embed the rootfs into the FIT image. FIT images do not need to contain a
rootfs, when they do not the kernel will fall-back to the kernel argument
'root', if this is not defined the kernel will not boot. It is safe to
add this as when we do have the rootfs in FIT this argument is ignored.
As 'loadfit' is only called from the MMC boot path, use 'args_mmc' to
correctly populate 'bootargs'.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-04-08 09:26:49 -04:00
Vignesh R
3f18ff07c8 ARM: keystone: Pass SPI MTD partition table via kernel command line
SPI U-Boot image for K2 boards have now exceeded 512K partition
allocated to it and no longer fit the partitions defined in kernel DTS
file. Therefore, pass an updated MTD partition table from U-Boot as
kernel command line arguments to avoid kernel from accidentally
modifying boot loader image that has overflowed to next user partition.

To do is, introduce a common environment file for declaring SPI
partition so that each individual boards need not repeat the same.
Choose appropriate SPI bus from board config file and pass it as command
line argument to kernel.

Signed-off-by: Vignesh R <vigneshr@ti.com>
2017-04-08 09:26:47 -04:00
Maxime Ripard
d6a7e0cbe3 sunxi: Add default environment size
On boards that defines ENV_IS_NOWHERE, such as the NES classic, commit
19dbe7d1a3f7 ("common: Move environment choice to Kconfig") broke the build
because of a missing environment size.

Reintroduce a default environment size consistent with what we had before.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-04-07 11:23:46 +05:30
Maxime Ripard
c8564b24ab sunxi: Add the default mtdids and mtdparts to our env
In order for the user to be able to see and modify them, add those
variables to the default environment.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-04-07 11:23:46 +05:30
Hans de Goede
d482a8dfba sunxi: Enable UBI and NAND support
Enable the NAND and UBI support in the configuration header so that we can
(finally) use it.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Jagan Teki <jagan@openedev.com>
2017-04-07 11:23:46 +05:30
Maxime Ripard
fb1c43cc37 common: Move environment choice to Kconfig
The environment location is something that might change per board
(depending on what storage options are availaible there) or depending on
the user choice (when we have several options).

Instead of hardcoding it in our configuration header, create a Kconfig
choice with the options we use for now, and the symbols that depend on it.

Once done, also remove the irrelevant sunxi defines.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-04-07 11:23:45 +05:30
Tom Rini
01abae4d04 Remove various unused interrupt related code
With d53ecad92f some unused interrupt related code was removed.
However all of these options are currently unused.  Rather than migrate
some of these options to Kconfig we just remove the code in question.

The only related code changes here are that in some cases we use
CONFIG_STACKSIZE in non-IRQ related context.  In these cases we rename
and move the value local to the code in question.

Fixes: d53ecad92f ("Merge branch 'master' of git://git.denx.de/u-boot-sunxi")
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-04-06 20:42:18 -04:00
Tom Rini
d53ecad92f Merge branch 'master' of git://git.denx.de/u-boot-sunxi
trini: Disable CONFIG_SPL_USE_ARCH_MEMSET on orangepi_2

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-04-06 20:40:24 -04:00
Simon Glass
e47b2d674f board_f: Make relocation functions generic
This header file is used by three archs. It could be used by all of them
since relocation is a common function. Move it into a generic file.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-04-05 16:36:57 -04:00
Simon Glass
96d4b75c0d board_f: Make init_helpers generic
This header file is used by two archs. It could be used by all of them
since it allows the cache to be on during relocation. Move it into a
generic file.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-04-05 16:36:56 -04:00
Simon Glass
e5fb573f64 powerpc: Move setup_board_extra() into a PPC file
We don't need this PPC-specific function in generic code. Move it to
the powerpc directory.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
2017-04-05 16:36:55 -04:00
Simon Glass
5e924a13e7 Move dram_init_banksize() to a common header
This is an weak function present on all archs so we should have it in the
common header file. Remove it from arch-specific headers and add a
function comment.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-04-05 16:36:51 -04:00
Simon Glass
088454cde2 board_f: Drop return value from initdram()
At present we cannot use this function as an init sequence call without a
wrapper, since it returns the RAM size. Adjust it to set the RAM size in
global_data instead, and return 0 on success.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
2017-04-05 13:59:20 -04:00
Simon Glass
52c411805c board_f: Drop board_type parameter from initdram()
It looks like only cm5200 and tqm8xx use this feature, so we don't really
need it in generic code. Drop it and have the users access gd->board_type
directly.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
2017-04-05 13:58:44 -04:00
Simon Glass
eca803756a i2c: Drop CONFIG_SOFT_I2C_MULTI_BUS
This is not used by any board. Drop it.

Signed-off-by: Simon Glass <sjg@chromium.org>
Clean up board_f sequence a little
This series tries to remove #ifdefs from the board_f init sequence. It
gets as far as I2C and then we need to discuss whether we can start to
remove the old I2C framework.

I think that ideally each entry in the init sequence should be enabled by
at most one CONFIG, which is in Kconfig and is not arch-specific.
END
Acked-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
2017-04-05 13:55:11 -04:00
Simon Glass
664ee4c995 i2c: Drop unused i2c_soft...() functions
These are not used in U-Boot. Manual relocation fixup is used by blackfin
but that is being removed.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-04-05 13:55:10 -04:00
Simon Glass
8749fa6af3 board_f: powerpc: Make prt_8260_rsr(), prt_8260_clks() private
Move these two function calls into checkcpu(), which is called on this
arch immediately after these two.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
2017-04-05 13:55:08 -04:00
Simon Glass
689697785e board_f: sandbox: Move sandbox_early_getopt_check() into misc_init_f()
We don't need a special hook for sandbox as one of the later ones will do
just as well. We can print error messages about bad options after we
print the banner. In fact, it seems better.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
2017-04-05 13:55:07 -04:00
Simon Glass
d891ab95c2 board_f: powerpc: Move prt_83xx_rsr() to private code
This function is called just before checkcpu() on MPX83xx. Move it to the
code for that arch.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-04-05 13:55:06 -04:00
Simon Glass
70e2aaf380 board_f: powerpc: Use timer_init() instead of init_timebase()
There is no good reason to use a different name on PowerPC. Change it to
timer_init() like the others.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2017-04-05 13:54:29 -04:00
Simon Glass
75efc34bfa board_f: Remove adjust_sdram_tbs_8xx() from the init sequence
We can just call this from the only place that needs it.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
2017-04-05 13:52:52 -04:00
Simon Glass
26345552d6 board_f: Remove sdram_adjust_866() from the init sequence
We can just call this from the only function that needs it.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
2017-04-05 13:52:51 -04:00
Simon Glass
d593c61672 board_f: powerpc: Rename get_clocks_866() to get_clocks()
We really don't need to have a name like this in the generic init
sequence. Use the generic get_clocks() name so that we can merge these
two at some point.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2017-04-05 13:52:50 -04:00
Simon Glass
671549e5b0 board_f: x86: Rename x86_fsp_init() to arch_fsp_init()
While x86 is the only user and this could in principle be moved to
arch_cpu_init() there is some justification for this being a separate
call. It provides a way to handle init which is not CPU-specific, but
must happen before the CPU can be set up.

Rename the function to be more generic.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
2017-04-05 13:52:36 -04:00
Simon Glass
2d986c0f54 board_f: initcall: Add a header guard
This file is missing the usual header guard. Add it.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-04-05 13:52:35 -04:00