U-Boot and SPL don't necessary share the same location, so we might end
with U-Boot SPL in read-only memory (XIP) and U-Boot in read-write memory.
In case of non XIP boot mode, we rely on such variables as "hart_lottery"
and "available_harts_lock" which we use as atomics.
The problem is that CONFIG_XIP also propagate to main U-Boot, not only SPL,
so we need CONFIG_SPL_XIP to distinguish SPL XIP from other XIP modes.
This adds an option special for SPL to behave it in XIP manner and we don't
use hart_lottery and available_harts_lock, during start proccess.
Signed-off-by: Nikita Shubin <n.shubin@yadro.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Add a simple uclass test for SCSI. It reads the partition table from a
disk image and checks that it looks correct.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present sandbox is producing a warning about SCSI migration. Drop the
legacy code and replace it with a new implementation.
Also drop the SATA command, which does not work with driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
The following faulty behavior was observed. The sandbox configured with
CONFIG_SANDBOX_CRASH_RESET=y was invoked with
./u-boot -T -S
After executing `exception undefined' the sandbox reboots.
When executing `exception undefined' the sandbox exits with SIGSEGV.
The expected behavior is that the sandbox should reboot again.
If we are relaunching the sandbox in a signal handler, we have to unblock
the respective signal before calling execv(). See signal(7) man-page.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
During init_dram() is called also setup_ddr_tlbs_phys() function which may
print message about unmapped DDR memory. So in this case print also
re-aligning filler after unmapped DDR memory message.
Signed-off-by: Pali Rohár <pali@kernel.org>
Currently U-Boot SPL prints just generic message "2 GiB left unmapped".
Change it to more detailed "2 GiB of DDR memory left unmapped in U-Boot".
This is just U-Boot configuration and operating system may map more (or
also less) memory.
Signed-off-by: Pali Rohár <pali@kernel.org>
Commit 37dc958947 ("global_data.h: Change ram_top type to phys_addr_t")
changed type of ram_top member from ulong to phys_addr_t but did not
changed types in board_get_usable_ram_top() function which returns value
for ram_top.
So change ulong to phys_addr_t type also in board_get_usable_ram_top()
signature and implementations.
Fixes: 37dc958947 ("global_data.h: Change ram_top type to phys_addr_t")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
The input clock for uart is too slow (25MHz) which introduces frequent data
error on both receiving and transmitting even if the baudrate is 115200.
Using high-speed can significantly solve this issue.
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds general board files based on MT7981 SoCs.
MT7981 uses one mmc controller for booting from both SD and eMMC, and the
pins of mmc controller are also shared with spi controller.
So three configs are need for these boot types:
1. mt7981_rfb_defconfig - SPI-NOR and SPI-NAND
2. mt7981_emmc_rfb_defconfig - eMMC only
3. mt7981_sd_rfb_defconfig - SD only
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Add general board files based on MT7986 SoCs.
MT7986 uses one mmc controller for booting from both SD and eMMC.
Both MT7986A and MT7986B use the same pins for spi controller.
Configs for various boot types:
1. mt7986_rfb_defconfig - SPI-NOR and SPI-NAND for MT7986A/B
2. mt7986a_bpir3_emmc_defconfig - eMMC for MT7986A only
3. mt7986a_bpir3_sd_defconfig - SD for MT7986A only
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds basic support for MediaTek MT7981 SoC.
This include the file that will initialize the SoC after boot and its
device tree.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds basic support for MediaTek MT7986 SoC.
This include the file that will initialize the SoC after boot and its
device tree.
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Remove the unnecessary nodes for TFABOOT and keep the mandatory part
in SOC dtsi, only the DDRCTRL and DDRPHY addresses.
This patch allows to manage the DDR configuration setting in U-Boot
device tree only if it is needed, when CONFIG_SPL is defined.
With TFABOOT, the DDR configuration is done in TF-A BL2 and the DDR size
is dynamically computed in U-Boot since commit d72e7bbe7c ("ram:
stm32mp1: compute DDR size from DDRCTL registers").
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Change the mask of OTP0 used to close the device on STM32MP
- STM32MP15x: bit 6 of OPT0
- STM32MP13x: 0b111111 = 0x3F for OTP_SECURED closed device
And support the 2 keys for STM32MP13x
- PKHTH : Hash of the 8 ECC Public Keys Hashes Table
(ECDSA is the authentication algorithm)
- EDMK : Encryption/Decryption Master Key
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Update the command stm32key to support several keys selected by
key name and managed by the new sub-command:
stm32key list
stm32key select [<key>]
stm32key read -a
This patch doesn't change the STM32MP15 behavior, only PKH is
supported, but it is a preliminary patch for STM32MP13 support.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Split the read_hash_otp function and introduce the helper function
read_close_status to read the close status in OTP separately of the PKH.
This patch is a preliminary step for STM32MP13 support.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add defines for value used in stm32key for BSEC permanent lock status
and error.
This patch is a preliminary step to support more lock status in BSEC
driver.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Improve the partitioning trace done in command stm32prog:
- remove the trace "partition: Done" when the GPT partitioning is not done
- indicate the mmc instance used for each 'gpt write' command
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
As the SMC is only supported in SP-MIN for STM32MP15x, the associated
partition should be absent when the TA NVMEM is not available in OPT-TEE
in STM32MP13x.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Solve many compilation warning when stm32prog is activated on the aarch64.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Change the defaut flashlayout location, hardcoded at STM32_DDR_BASE,
to CONFIG_SYS_LOAD_ADDR to avoid issue on board with reserved memory
at STM32_DDR_BASE.
This patch changes the command behavior for STM32MP13 and STM32MP15
platform, as CONFIG_SYS_LOAD_ADDR(0xc2000000) != STM32_DDR_BASE
but without impact for serial boot with STM32CubeProgrammer.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
When the STM32CubeProgrammer sent a empty flashlayout.tsv
file, the command stm32prog correctly parse the file
but data->dev_nb = 0 and the stm32prog_devices_init
operations should be skipped.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
TI DP83867 is using strapping based on MIO pins. Tristate setup can influce
PHY address. That's why switch description with ethernet-phy-id compatible
string which enable calling reset. PHY itself setups phy address after
power up or reset. Reset description will be added in separate commit.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/52bf9ac0453d4e4896d8edd2618e684bb1ff6012.1662721547.git.michal.simek@amd.com
The upstream Linux DSA drivers do not require phy-handle nodes in
the DSA ports yet the U-Boot DSA drivers do. Add a phy-handle and
the mdio nodes to the u-boot.dtsi file so that future dts file
syncrhonization between Linux and U-Boot don't break networking.
Fixes: 24a7a3c1c0 ("imx8mm: synchronise device tree with linux")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The upstream Linux DSA drivers do not require phy-handle nodes in
the DSA ports yet the U-Boot DSA drivers do. Add a phy-handle and
the mdio nodes to the u-boot.dtsi file so that future dts file
syncrhonization between Linux and U-Boot don't break networking.
Fixes: e0caa84ca6 ("imx8mp: synchronise device tree with linux")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmMoEdgcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyNvEB/4nEeiBx7Lo1gK+79PJ
9kCUngglHRu3/+FJMpcOp+2b6sSW1IZs8qGBMAMFSRoFElrLMMbVEgBR0ZfJCl3c
It0xN9Buhe8muwtAdE8Amr4PddUEynzglVPpFUFfir6ZqFAcedmN6iuh+K82r7Be
7s/8tRb2hVp//TpkEntf2yxrYnyeW4qiXyUxbUhaUyyhkM3RBXySuY4qnaaLp3NY
R9rsIY5j3kA2QylebEamlXI+KDvszrGbkUOUUrlwkygQNR/GmAYQPlY1TdBwk0wE
U1CO8zQYaL3OY998lU32pMVClmwyXbn2i7KAyMm3TEgrfpjQsLTS2BK+w+RBdMGL
XGnt
=lRvM
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2023.01-a' of https://source.denx.de/u-boot/custodians/u-boot-at91 into next
First set of u-boot-at91 features for the 2023.01 cycle:
This feature set includes the important update on PIO4 pinctrl driver
that solves a long time mismatch between Linux and U-boot, related on
the unification of pinctrl and gpio driver support, now respecting the
pinctrl bindings ABI; and also support for pinctrl subnodes. The feature
set also adds support for PDA screen detection for sam9x60_curiosity
board , one fix for SD-Card reinsertion and one fix for sam9x60 clocks.
Adding the "u-boot,dm-pre-reloc" DT property to the timer node is
necesssary to support the timer in the early boot phases (e.g.
SPL & pre-reloc).
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Tony Dinh <mibodhi@gmail.com>
Add the DT bindings / descriptions for timer0 & timer1, exactly as done
in mainline Linux.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Tony Dinh <mibodhi@gmail.com>
This patch changes the compilation, so that the Armada 375 board(s) are
compiled in a separate step. This is necessary for the timer dts
conversion, as A375 has a different / timer description in the dts.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Tony Dinh <mibodhi@gmail.com>
Now that the new timer support is available for these platforms, let's
select this IF for all these platforms. This way it's not necessary
that each board changes it's config header.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Tony Dinh <mibodhi@gmail.com>
With the recent changes in the Marvel mvneta network driver, the MDIO
bus is not connected any more. This patch updates the DT nodes to use
the nodes from the dtsi files instead of creating ad-hoc nodes.
Signed-off-by: Stefan Roese <sr@denx.de>
I messed up application of patch 5a428e7510 ("mmc: fsl_esdhc_spl: Add
support for builds without CONFIG_SYS_MMC_U_BOOT_OFFS"). I took it from
a work-in-progress branch where I changed usage of
CONFIG_SDCARD to CONFIG_SD_BOOT
and refactored
SYS_MPC85XX_NO_RESETVEC
mess.
But these changes aren't in master yet. Fix the wrong usage of these
macros.
Fixes: 5a428e7510 ("mmc: fsl_esdhc_spl: Add support for builds without
CONFIG_SYS_MMC_U_BOOT_OFFS")
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Pali Rohár <pali@kernel.org>
This patch makes sure that the Devicetree for the sama7
boards are aligned with the Devicetree from Linux. This
implies removing the GPIO compatible and replacing it
with the PINCTRL one, as well as unifying the SDMMC
pinctrl related subnodes under one single subnode.
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
This patch makes sure that the Devicetree for the sama5
boards are aligned with the Devicetree from Linux. This
implies removing the GPIO compatible and replacing it
with the PINCTRL one, as well as unifying the SDMMC
pinctrl related subnodes under one single subnode.
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
Fix copy-paste error of the I2C5 bus recovery GPIO assignment,
the I2C5 GPIOs are on gpio3 instead of gpio5.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: uboot-imx <uboot-imx@nxp.com>
The ECSPI1 is on I2C1/I2C2 pins of the SoC, update the pinmux accordingly.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: uboot-imx <uboot-imx@nxp.com>
Rename imx8mp-dhcom-pdk2-u-boot.dtsi to imx8mp-dhcom-u-boot.dtsi, since
this file is shared by PDK2, PicoITX and DRC02. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: uboot-imx <uboot-imx@nxp.com>
This PHY is not used on PDK2, the header was added due to copy-paste
error, drop it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: uboot-imx <uboot-imx@nxp.com>
Add information about which exact SoM variant is used on which PDK2 variant.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: uboot-imx <uboot-imx@nxp.com>
When the imx8mm.dtsi file was pulled in from Linux, the UARTs
were moved into an spba sub-node which wasn't being included
in the SPL device tree. This meant the references to the UART
weren't being handled properly and when booting the system would
constantly reboot. Fix this by adding the spba node to the spl
device tree to restore normal booting.
Fixes: 4e5114daf9 ("imx8mn: synchronise device tree with linux")
Signed-off-by: Adam Ford <aford173@gmail.com>
Fix spurious ampersand in address print e.g.
Find img info 0x&480331a0, size 855
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>"
The NXP i.MXRT1170 Evaluation Kit (EVK) provides a platform for rapid
evaluation of the i.MXRT, which features NXP's implementation of the Arm
Cortex-M7 and Cortex-M4 core.
The EVK provides 64 MB SDRAM, Micro SD card socket,
USB 2.0 OTG.
This patch aims to support the preliminary booting up features
as follows:
GPIO
LPUART
SD/MMC
SDRAM
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
This commit adds board support for i.MXRT1170-EVK from NXP. This board
is an evaluation kit provided by NXP for i.MXRT117x processor family.
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Only one occurance of WATCHDOG_RESET is left in one assembler file.
This patch changes this occurance to a direct call to watchdog_reset
and then removes all the ASSEMBLY ifdef'ery in watchdog.h, as it's not
needed any more to clean this mess a bit up.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Tom Rini <trini@konsulko.com> [am335x_evm, mx6cuboxi, rpi_3,dra7xx_evm, pine64_plus, am65x_evm, j721e_evm]
Globally replace all occurances of WATCHDOG_RESET() with schedule(),
which handles the HW_WATCHDOG functionality and the cyclic
infrastructure.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Rini <trini@konsulko.com> [am335x_evm, mx6cuboxi, rpi_3,dra7xx_evm, pine64_plus, am65x_evm, j721e_evm]
When fixed offset via CONFIG_SYS_MMC_U_BOOT_OFFS is not specified then
expects that U-Boot proper is placed immediately after SPL without any
additional padding.
This allows to generate smaller SPL+U-Boot final binary as it is not
required to specify fixed offset to U-Boot proper at SPL compile time.
In this case offset to U-Boot proper is calculated at SPL compile time in
linker script.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Change 8-byte alignment of SPL binary to just 4-byte alignment as objcopy
trims trailing zero bytes when converting ELF file to RAW binary.
This is same fix for SPL linker script as was done fix for U-Boot linker
script in commit e8c0e0064c ("powerpc: mpc85xx: Fix CONFIG_OF_SEPARATE
support").
It is required for the patch "mmc: fsl_esdhc_spl: Add support for builds
without CONFIG_SYS_MMC_U_BOOT_OFFS" which triggered this issue in SPL.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Commit d433c74eec ("Convert CONFIG_SDCARD et al to Kconfig") converted
SYS_EXTRA_OPTIONS=SDCARD or SPIFLASH to config options CONFIG_SDCARD and
CONFIG_SPIFLASH, but left one occurance unchanged.
Fix this.
Fixes: d433c74eec ("Convert CONFIG_SDCARD et al to Kconfig")
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Pali Rohár <pali@kernel.org>
Building of final u-boot.bin binary for mpc85xx via binman is needed only
when inserting DTB binary in the middle of the u-boot ELF binary (before
.bootpg and .resetvec ELF sections).
These requirements are met when CONFIG_MPC85XX_HAVE_RESET_VECTOR is enabled
(= generating .bootpg/.resetvec sections) and CONFIG_OF_SEPARATE is enabled
(= inserting DTB binary).
So in all other cases use standard build procedure instead of custom
mpc85xx u-boot.bin Makefile target via binman.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Currently Makefile produces final mpc85xx image when SPL is not used in
custom file u-boot-with-dtb.bin. It is quite confusing name as build
process produce also intermediate file standard file u-boot-dtb.bin (which
is just intermediate and not bootable). Other platforms use u-boot.bin
(UBOOT_BIN) as standard name for final bootable raw image.
So change Makefile rules and binman to produce final bootable file for
mpc85xx also into file u-boot.bin. There is just need for mpc85xx to not
define default rule for u-boot.bin then instruct binman (via DTS file) to
store final image into u-boot.bin (instead of u-boot-with-dtb.bin) and
finally rename target u-boot-with-dtb.bin to u-boot.bin.
With this change are also removed custom Makefile hacks for mpc85xx that it
produced non-standard output file. And also updated documentation.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
We currently have an if_type (interface type) and a uclass id. These are
closely related and we don't need to have both.
Drop the if_type values and use the uclass ones instead.
Maintain the existing, subtle, one-way conversion between UCLASS_USB and
UCLASS_MASS_STORAGE for now, and add a comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
Enable this option on all boards which support block devices. Drop the
related depencies on BLK since these are not needed anymore.
Disable BLOCK_CACHE on M5253DEMO as this causes a build error.
Signed-off-by: Simon Glass <sjg@chromium.org>
* Remove unnecessary device tree nodes which are not needed in
U-Boot directly.
* Move all U-Boot specific device tree properties to u-boot dtsi.
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Commit 6337d53fdf ("arm: dts: sync am33xx with Linux 5.9-rc7") syncs
the am335x device tree with the latest linux kernel am335x device tree.
That causes problems with device tree in SPL stage.
To fix the issues CONFIG_SPL_OF_TRANSLATE must be set to handle the
synced bus addresses correctly.
A custom U-Boot device tree is also needed since the SPL build removes
bus properties from bus nodes which are not explicitly marked with the
u-boot,dm-spl or u-boot,dm-pre-reloc flag. Therefore all parent buses of
the in the SPL needed devices must be marked with u-boot,dm-pre-reloc.
Also since there is no driver for "ti,sysc" compatible property in SPL
the buses marked with this compatible string must also be marked with
compatible = "simple-bus" to make the underlying devices visible in
SPL. Otherwise the matching device drivers aren't found and the uclass
drivers are dropped.
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
The SPI and NAND board variants never went into production.
Drop those board variants.
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Add functions to read 8/16-bit integers like the existing functions for
32/64-bit to simplify read of 8/16-bit integers from device tree
properties.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
This is required for architectures which do not support compressed kernel images (i.e. ARM64). This is only used while not booting via FIT image.
Signed-off-by: Nathan Barrett-Morrison <nathan.morrison@timesys.com>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
GQSPI driver is using it but this function is never called for Versal
because it is removed by linker. But function should be declared to avoid
this build warning:
drivers/spi/zynqmp_gqspi.c: In function 'zynqmp_qspi_set_tapdelay':
drivers/spi/zynqmp_gqspi.c:378:3: warning: implicit declaration of function
'zynqmp_mmio_write' [-Wimplicit-function-declaration]
378 | zynqmp_mmio_write(IOU_TAPDLY_BYPASS_OFST,
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20220825125906.11581-3-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Added ref_clk 'ref' property for GUCTL_REFCLKPER and GFLADJ_REFCLK_FLADJ
calculation. This property configure correct value for SOF/ITP counter
and period of ref_clk.
This patch adds 'ref' property for both dwc3_0 and dwc3_1 cores.
Signed-off-by: Piyush Mehta <piyush.mehta@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/417545b948ea12a9301a5e80851f98523be2b443.1661259809.git.michal.simek@amd.com
Update MTD partitions of Kria device trees to allocate 128KB of QSPI
memory for secure OS. Increased "SHA256" partition size & changed
starting address of "User" partition to accommodate the new partition
"Secure OS Storage"
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/9cc64b8c731d11439de73d0af54c65080068f00b.1661242681.git.michal.simek@amd.com
Commit 5bb2c550b1 ("arm: mvebu: Move internal registers in
arch_very_early_init() function") moved code from file cpu.c to lowlevel.c,
which moves Marvell internal registers from address INTREG_BASE_ADDR_REG to
SOC_REGS_PHY_BASE.
But the steps describing how to do it correctly were documented only in
older U-Boot versions and commit cefd764222 ("arm: mvebu: Fix internal
register config on A38x") probably unintentionally removed important
details about MMU from code comments around.
Commit 5bb2c550b1 ("arm: mvebu: Move internal registers in
arch_very_early_init() function") implemented code movement according to
(now incomplete) comments which resulted in semi-broken code.
The result is that I-cache is currently disabled for all Armada 38x boards
and maybe there are some other (unreported / undetected) issues.
Reimplement it correctly. First flush all caches, then disable MMU and L2
cache and then move Marvell internal registers. There is no need to
explicitly disable I-cache.
After this change lzmadec command with lzma image of 0x7000000 bytes is
doing decompression just 5 seconds. Before this change it was 30 seconds.
To make lowlevel.S code more readable, extend asm/pl310.h header file to be
compatible with assembler and use macros from this file.
Fixes: 5bb2c550b1 ("arm: mvebu: Move internal registers in arch_very_early_init() function")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
For some unknown reason when L2 cache is disabled on Armada 385 then loadb,
loadx and loady commands do not work with higher baudrates than 115200
(they just abort transfer) and lzmadec command with lzma image of size
0x7000000 (maybe even smaller, we tested this one) is doing decompression
for more than 2 minutes. After enabling L2 cache decompression takes only
30s and loadb, loadx and loady are stable and working fine.
git bisect identified problematic commit 3308933d2f ("arm: mvebu: Avoid
reading MVEBU_REG_PCIE_DEVID register too many times"). Before this commit
above issues were not present.
But investigation showed that above issue was possible to reproduce also by
reverting that commit and forcing compiler to do inline optimization of
mvebu_soc_family() function. Which seems that the root of this issue is in
caches and position of instruction of segments. So currently it is unknown
what is or was broken, but code movement, code inlining or other compiler
optimization triggered it.
Commit 3e5ce7ceeb ("arm: mvebu: Enable L2 cache on Armada XP") mentioned
that enabling L2 cache on Armada XP improved performance and that Armada
38x has L2 disabled (which is default state) and if needed it has to be
enabled in separate patch. As enabling L2 cache also improve performance
on Armada 38x, enable it.
Note that Aurora cache in no outer mode is available only on Armada XP,
hence it is not touched for Armada 38x code.
Fixes: 3308933d2f ("arm: mvebu: Avoid reading MVEBU_REG_PCIE_DEVID register too many times")
Reported-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Replace magic constant 1 when disabling MMU by macro CR_M from include
header file asm/system.h.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Commit c86d53fd88 ("arm: mvebu: Don't disable cache at startup on Armada
XP at all") introduced branch for non-AXP code which was guarded by A38X
condition. Fix this issue by checking for AXP platform, not by A38X.
Fixes: c86d53fd88 ("arm: mvebu: Don't disable cache at startup on Armada XP at all")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Commit 3308933d2f ("arm: mvebu: Avoid reading MVEBU_REG_PCIE_DEVID
register too many times") broke support for caches on all Armada SoCs.
Before that commit there was code:
if (mvebu_soc_family() != MVEBU_SOC_A375) {
dcache_enable();
}
And after that commit there is code:
if (IS_ENABLED(CONFIG_ARMADA_375)) {
dcache_enable();
}
Comment above this code says that d-cache should be disabled on Armada 375.
But new code inverted logic and broke Armada 375 and slowed down all other
Armada SoCs (including A38x).
Fix this issue by changing logic to:
if (!IS_ENABLED(CONFIG_ARMADA_375)) {
dcache_enable();
}
Which matches behavior prior that commit.
Fixes: 3308933d2f ("arm: mvebu: Avoid reading MVEBU_REG_PCIE_DEVID register too many times")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Move arm twd timer driver from zynq to generic location.
DM timer drivers are designed differently to original driver. Timer is
counting up and not down.
Information about clock rates are find out in timer_pre_probe() that's
why there is no need to get any additional information from DT in the
driver itself (only register offset).
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Link: https://lore.kernel.org/r/20220805061629.1207-1-stefan.herbrechtsmeier-oss@weidmueller.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
- remove test on CONFIG_DM_REGULATOR in stm32mp1 board
and enable CONFIG_DM_REGULATOR for stm32f769-disco
- handle ck_usbo_48m clock provided by USBPHYC to fix the command 'usb start'
after alignment with Linux kernel v5.19 DT (clocks = <&usbphyc>)
- Fix SYS_HZ_CLOCK value for stih410-b2260 board
- Switch STMM32MP15x DHSOM to FMC2 EBI driver
- Remove hwlocks from pinctrl in STM32MP15x to avoid issue with kernel
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAmMZoW4ACgkQ4rK92eCq
k3W2MAgAsmy2aSlMYo/AGlJ/KCrZuk6OirNHtdOdacvbcdUUbpkNpBSjdkrRm2If
VUnY1utIIJe6gFgnBUxXJ3RF5FZuhkdawc6V25HtDp6H3WamzJknKs5Vc4TlKp59
hZCOto7/+G/cd2XLdCKFUBl+new1pdDPsEm56+57DeZ7QGAQRX35PUQ5+HBjQJ/N
n/wJgS6wkEdIQLLwmCVxbHUkC+pRotTza5F2A0qZJgYPMcMpVFYKtzIa4GbWB5YS
MKGHbM8f3C8RLPQaHHTRycoA2Yor1I52B4Oi7605c5zHQr9pjrgtWsernDzkIhsB
ThYHSYQBUBTY4HBfzFwzCkVGqqLWNg==
=PMFY
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20220907' of https://source.denx.de/u-boot/custodians/u-boot-stm
- simplify the STM32MP15x package parsing code
- remove test on CONFIG_DM_REGULATOR in stm32mp1 board
and enable CONFIG_DM_REGULATOR for stm32f769-disco
- handle ck_usbo_48m clock provided by USBPHYC to fix the command 'usb start'
after alignment with Linux kernel v5.19 DT (clocks = <&usbphyc>)
- Fix SYS_HZ_CLOCK value for stih410-b2260 board
- Switch STMM32MP15x DHSOM to FMC2 EBI driver
- Remove hwlocks from pinctrl in STM32MP15x to avoid issue with kernel
This reduces sec_firmware_get_data to a single call to
fit_get_data_conf_prop. I think sec_firmware_check_copy_loadable could also
be converted, but it does not map as straightforwardly, so I have left it
for a future cleanup.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The config to use for FIT images can be better specified by enabling
CONFIG_MULTI_DTB_FIT and implementing board_fit_config_name_match.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Removes hwlocks properties from stm32mp151 pinctrl node. These locks
could be used for other purpose, depending on board and software
configuration hence do not enforce their use to protect pinctrl
devices.
This patch is an alignment with Linux device tree with v6.0 as the
hwsem support wasn’t yet added in pincontrol in kernel. It avoids
issues when the Linux kernel is started with the U-Boot device tree.
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Perform long overdue conversion of ad-hoc FMC2 EBI bus initialization
to upstream FMC2 EBI driver. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Since commit ef4ce6df32 "video: stm32: stm32_ltdc: fix data enable polarity"
The panel display output wasn't functional anymore.
Device tree display-timings de-active property value must be updated
to 1.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Simplify the package parsing code for STM32MP15X as package can be
affected with get_cpu_package() result.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
P1/P2 RDB boards have external max6370 watchdog connected to CPLD and this
watchdog is not deactivated on board reset. So if it is active during board
reset, it can trigger another reset when CPU is booting U-Boot. To prevent
possible infinite reset loop caused by external watchdog, turn it off
before reset.
Do it via a new board_reset_prepare() callback which is called from
do_reset() function before any reset sequence.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
CPLD's system reset register is buggy and requires workaround in U-Boot.
So use this kind of board reset only when there is no other reset option.
Introduce a new board_reset_last() callback which is last-stage
board-specific reset and implement CPLD's system reset in this new
board_reset_last() callback instead of board_reset() callback.
Fixes: 20fb58fc5a ("board: freescale: p1_p2_rdb_pc: Implement board_reset()")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This commit sychronizes the header file for FU740 PRCI clocks with the
one from Linux 5.19.
The constant values are the same, but all constant names are changed
(most are just prefixed with FU740_).
Signed-off-by: Icenowy Zheng <uwu@icenowy.me>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
By default the OCRAM is marked as secure. While the SPL runs in EL3 and
thus can access it, DMA devices cannot. Mark the whole OCRAM as
non-secure.
This will fix MMC and SD card boot on LS1028A when using SPL instead of
TF-A.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This adds the onkey, RTC and watchdog children to the DA9063 PMIC node,
fixes the compatible for qspi0's flash node to match the official DT
schema (it being an is25wp256 is discoverable, hence jedec,spi-nor is
the only compatible that should be present) and exposes the card detect
GPIO.
Note that the device trees still diverge in some places (including
important things like the PCIe controller's clock name) and should be
cleaned up so that a common device tree is used in both projects rather
than having different bindings. This patch does not attempt to do that,
merely expose important functionality present in Linux's that is not in
U-Boot's so that it can be used without the OS providing its own bundled
copy.
Signed-off-by: Jessica Clarke <jrtc27@jrtc27.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
This new image is similar to u-boot-rockchip.bin except that it's
destined to be flashed on SPI-NOR flashes.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This prepares for the creation of a u-boot-rockchip-spi.bin image
similar to u-boot-rockchip.bin to the exception it's destined for
SPI-NOR flashes instead of MMC storage medium.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This allows to build u-boot-rockchip.bin binary with binman for Rockchip
ARM64 boards instead of the legacy Makefile way.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
idbloader.img content - currently created by way of Makefile - can be
created by binman directly.
So let's do that for Rockchip ARM platforms.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
While technically not a bug, let's have some consistency in paths
returned by u-boot,spl-boot-order look-up and the one saved in
u-boot,spl-boot-device by syncing spl_boot_devices_tbl and boot_devices
node paths.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Tested-by: Xavier Drudis Ferran <xdrudis@tinet.cat>
Reviewed-by: Xavier Drudis Ferran <xdrudis@tinet.cat>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
On RK3399, mmc0 is eMMC and mmc1 is SD card, c.f. console:
MMC: mmc@fe320000: 1, mmc@fe330000: 0
In arch/arm/mach-rockchip/spl-boot-order.c:board_boot_order, the
boot_device (BOOT_DEVICE_*) value is gotten from spl_node_to_boot_device
function. Said function returns BOOT_DEVICE_MMC1 for mmc0 (eMMC) and
BOOT_DEVICE_MMC2 for mmc1 (SD card).
Since the SD card controller is at mmc@fe320000, it should be associated
with BOOT_DEVICE_MMC2 and not BOOT_DEVICE_MMC1. Same applies to eMMC.
Let's fix that by swapping the two BOOT_DEVICEs.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Tested-by: Xavier Drudis Ferran <xdrudis@tinet.cat>
Rockchip SoCs need the boot_devices array defined in order to map the
bootloader's value to a U-Boot device. Implement this for rk3308.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@vrull.eu>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
When idbloader.img is flashed on the eMMC, the SPL still tries to load
from SPI-NOR first.
This is due to an incorrect look-up in the Device Tree. Since commit
822556a934 ("arm: dts: sync the Rockhip 3399 SoCs from Linux"), the
node name (but not label) changed from sdhci@fe330000 to mmc@fe330000
meaning U-Boot SPL is not looking for the correct node name anymore and
fails to find the "same-as-spl" node when eMMC is the medium from which
the SPL booted.
Fixes: 822556a934 ("arm: dts: sync the Rockhip 3399 SoCs from Linux")
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Xavier Drudis Ferran <xdrudis@tinet.cat>
Reviewed-by: Artem Lapkin <email2tema@gmail.com>
Tested-by: Artem Lapkin <email2tema@gmail.com>
Tested-by: Lapkin Artem <email2tema@gmail.com>
Tested-by: Lapkin Artem <email2tema@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The boot_devices constants for rk3288 were changed to match the
binding, but the dtsi file was not synced.
Fix by renaming the rk3288 mmc node names.
Also correct the clock name for "ciu-drive".
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Some tests can have race conditions which are hard to detect on a single
one. Add a way to run tests more than once, to help with this.
Each individual test is run the requested number of times before moving
to the next test. If any runs failed, a message is shown.
This is most useful when running a single test, since running all tests
multiple times can take a while.
Signed-off-by: Simon Glass <sjg@chromium.org>
LTO (Link-Time Optimisation) is an very useful feature which can
significantly reduce the size of U-Boot binaries. So far it has been
made available for selected ARM boards and sandbox.
However, incremental builds are much slower when LTO is used. For example,
an incremental build of sandbox takes 2.1 seconds on my machine, but 6.7
seconds with LTO enabled.
Add a NO_LTO parameter to the build, similar to NO_SDL, so it can be
disabled during development if needed, for faster builds.
Add some documentation about LTO while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
There is currently a problem that U-Boot can not work on ARMv4
because assembly imlementations of memcpy() and some other functions
use "bx lr" instruction that is not available on ARMv4 ("mov pc, lr"
should be used instead).
A working preprocessor-based solution to this problem is found in
arch/arm/lib/relocate.S. Move it to the "ret" macro in
arch/arm/include/asm/assembler.h and change all "bx lr" code
to "ret lr" in functions that may run on ARMv4. Linux source code
deals with this problem in the same manner.
v1 -> v2:
Comment update. Pointed out by Andre Przywara.
Signed-off-by: Sergei Antonov <saproj@gmail.com>
CC: Samuel Holland <samuel@sholland.org>
CC: Ye Li <ye.li@nxp.com>
CC: Simon Glass <sjg@chromium.org>
CC: Andre Przywara <andre.przywara@arm.com>
CC: Marek Vasut <marex@denx.de>
CC: Sean Anderson <sean.anderson@seco.com>
CC: Tom Rini <trini@konsulko.com>
The compatible values used for device nodes representing Renesas Reduced
Pin Count Interfaces were based on preliminary versions of the Device
Tree Bindings.
Correct them in both DTSi files and drivers, to match the final DT
Bindings.
Note that there are no DT bindings for RPC-IF on RZ/A1 yet, hence the
most logical SoC-specific value is used, without specifying a
family-specific value.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
According to the Generic Names Recommendation in the Devicetree
Specification Release v0.3, and the DT Bindings for the Renesas Reduced
Pin Count Interface, the node name for a Renesas RPC-IF device should be
"spi". Especially on R-Car Gen3 and RZ/G2, the node name matters, as
the node is enabled by passing a DT fragment from TF-A to U-Boot, and
from U-Boot to subsequent software.
Fix this by renaming the device nodes from "rpc" to "spi".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Introduce the new Kconfig symbol CONFIG_SPL_SYS_L2_PL310 to allow the
SPL to build cache-pl310.c.
Before this commit, the SPL could enable the PL310 L2 cache [1], but the
cache maintenance functions from cache-pl310.c were only useable for
non-SPL builds.
After enabling the cache one must be able to flush it, too. Thus this
commit allows cache-pl310.c to be included in the SPL build.
[1] See for example arch/arm/mach-imx/cache.c: v7_outer_cache_enable()
Signed-off-by: Philip Oberfichtner <pro@denx.de>
This converts CONFIG_SYS_L2_PL310 to Kconfig.
For omap2 and mvebu the 'select SYS_L2_PL310' locations were
determined using ./tools/moveconfig -i CONFIG_SYS_L2_PL310.
For mx6 I manually chose ARCH_MX6 as 'select' location. The
correctness has been verified using
$ ./tools/moveconfig.py -f ARCH_MX6 ~SYS_L2_PL310 ~SYS_L2CACHE_OFF
0 matches
That means whenever an ARCH_MX6 board had SYS_L2_PL310 disabled, this
was correctly reflected in SYS_L2CACHE_OFF. Thus it's safe to insert
the 'select' statement under ARCH_MX6.
Signed-off-by: Philip Oberfichtner <pro@denx.de>
Newer versions of GCC won't initialize parts of structures which don't
appear to be used. This results in uninitialized semihosting parameters
passed via R1. Fix this by marking the inline assembly as clobbering
memory.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Currently for all Qcom SoCs/boards there are separate compatibles for
GPIO and pinctrl. But this is inconsistent with official (upstream) Linux
bindings which requires only a single compatible "qcom,<SoC name>-pinctrl"
and there is no such compatible property as "qcom,tlmm-<SoC name>".
So fix this inconsistency for Qcom SoCs in order to comply with upstream
DT bindings. This is done via removing compatibles from "msm_gpio" driver
and via binding to "msm_gpio" driver from pinctrl driver in case
"gpio-controller" property is specified for pinctrl node.
Suggested-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
DT compatible is sufficient to make platform specific differentiation,
so remove redundant CONFIG_SDM845 check.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
For USB3 host controller to detect devices on the bus it is required to
enable a PMIC GPIO: usb_vbus_boost_pin. So enable that during board
specific initialization.
And since this PMIC GPIO parsing is quite u-boot specific, so add a
DT override to qcs404-evb-uboot.dtsi to represent usb_vbus_boost_pin.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
QCS404 SoC provides support for two USB controllers: one USB3 and the
other one being USB2. The USB3 controller supports further 2 PHY: one high
speed PHY and the other super speed PHY. The USB2 controller supports a
single high speed PHY. So add corresponding DT nodes.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Drivers like USB, ethernet etc. uses ".enable" hook to enable clocks.
So add corresponding support for Qcom clock drivers.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
The board has only one network interface. The linux kernel will
gracefully skip a the ethernet interface if no connected PHY could be
probed. u-boot on the other hand will throw an error message. The kernel
device tree is about to be fixed. For now, just disable the ethernet
interface in our -u-boot.dtsi.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Use the new mvebu GPIO driver and convert all the function calls to the
former kirkwood GPIO driver. This means that we are now using the LED
uclass and the regulator uclass. Unfortunately, the GPIO LED doesn't
offer a blinking method. Thus we are now stuck with solid on and off
states, which makes debugging a bit harder. Also, there is no GPIO fan
driver for now.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
If something is wrong with the environment, we cannot rely on a proper
u-boot operation anymore. In fact, it is possible, that we never reach
misc_init_r() with a broken environment.
Also don't enable the netconsole by environment settings. This way the
user don't have to reconfigure the environment. Instead the network
console is only enabled when the push button is pressed during boot.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
The board code needs this to be set. Otherwise, the recovery mechanism
doesn't work. Therefore, select this option automatically with the
board.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
If we switch to CONFIG_TIMER, we don't need the legacy timer macros and
functions anymore. Add the proper guards to exclude them from compiling.
Cc: Pali Rohár <pali@kernel.org>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
mbus driver is initialized from arch_cpu_init() callback which is called
before relocation. This driver stores lot of functions and structure
pointers into global variables, so it is data position dependent.
Therefore after relocations all pointers are invalid and driver does not
work anymore as all pointers referes to the old memory, which overlaps with
CONFIG_SYS_LOAD_ADDR and ${loadaddr}.
For example U-Boot fuse command crashes if loadaddr memory is cleared or
rewritten by some image loaded by U-Boot load command.
mw.w ${loadaddr} 0x0 10000
fuse read 0 1 2
Fix this issue by removing of all mbus global variables in which are stored
pointers to structures or functions which changes during relocation. And
replace it by direct function calls (not via pointers). With this change
fuse command finally works.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Stefan Roese <sr@denx.de>
SPI0 CS0 Flash is mapped to address range 0xD4000000 - 0xD7FFFFFF by BootROM.
Proper U-Boot removes this direct mapping. So it is available only in SPL.
This applies for all 32-bit Armada BootROMs. SPL mvebu code is used only on
32-bit Armada SoCs. So move env_sf_get_env_addr() function from Turris
Omnia board to common SPL mvebu code and add proper checks for SPI0 CS0.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
The kmtegr1 board is out of maintenance and can be removed. As it is the
only board in the tree using MPC8309 the support for this CPU is dropped
completely.
Signed-off-by: Holger Brunck <holger.brunck@hitachienergy.com>
This board is missing migration to CONFIG_DM, which had a deadline of
v2020.01, which is now more than 2 years passed due. Remove it.
Cc: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have been orphaned for some time and are behind on various
DM migrations. Remove them.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The *aqds* platforms have not been migrated to be able to enable
CONFIG_DM_ETH with CONFIG_FMAN_ENET. Disable CONFIG_FMAN_ENET on these
platforms.
Cc: Mingkai Hu <mingkai.hu@nxp.com>
Cc: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Cc: Pramod Kumar <pramod.kumar_1@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This driver has not been converted to DM_ETH. The migration
deadline passed 2 years ago.
Cc: Trevor Woerner <twoerner@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Ramon Fried <rfried.dev@gmail.com>
This board is behind on several mandatory DM migrations and is missing
OF_CONTROL support that makes other conversions impossible. Remove it.
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Cc: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board is behind on several mandatory DM migrations and is missing
OF_CONTROL support that makes other conversions impossible. Remove it.
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board is behind on several mandatory DM migrations and is missing
OF_CONTROL support that makes other conversions impossible. Remove it.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Uri Mashiach <uri.mashiach@compulab.co.il>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board is not converted to use CONFIG_DM, well passed the migration
deadline. Remove it.
Cc: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The Yocto project builds their aarch64 cross-compiler with the
configure knob --enable-standard-branch-protection, which means that
their gcc behaves as if -mbranch-protection=standard is passed; the
default (lacking that configure knob) is -mbranch-protection=none.
This means that when building U-Boot using the Yocto toolchain, most
functions end up containing paciasp/autiasp/bti instructions. However,
since U-Boot is not an ordinary userspace application, there's no OS
kernel which has set up the required authentication keys, so these
instructions do nothing at all (even on arm64 hardware that does have
the pointer authentication capability). They do however make the image
larger.
It is theoretically possible for U-Boot to make use of the pointer
authentication protection - cf. the linux kernel's
CONFIG_ARM64_PTR_AUTH_KERNEL - but it is far from trivial, and it's
hard to see just what threat model it would protect against in a
bootloader context. Regardless, we certainly have none of the required
infrastructure now, so explicitly pass -mbranch-protection=none to
ensure those useless instructions do not get emitted.
For a toolchain not configured with
--enable-standard-branch-protection, this changes nothing. For the
Yocto toolchain, this reduces the size of both SPL and U-Boot proper
by about 3% for my imx8mp target.
If you don't have a Yocto toolchain, the effect can easily be
reproduced by applying this patch and changing =none to =standard.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Simon Glass <sjg@chromium.org>
pcm051_rev3_defconfig config (Phytec Wega board) has been dropped in
64efd11d ("arm: Remove pcm051 board")
due to expired migration deadlines. Here, pcm051_rev3_defconfig support is
reintroduced.
Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Some of config options are board specific and should be set in into their
default values automatically. So move them from defconfig file to Kconfig
definitions to ensure that possible user custom defconfig files would have
these required options also enabled.
Signed-off-by: Pali Rohár <pali@kernel.org>
Switch from custom board specific fixup/copy code to U-Boot generic
position independent code provided by config option POSITION_INDEPENDENT.
This also slightly decrease size of u-boot.bin binary (by 52 bytes). Note
that option POSITION_INDEPENDENT increase size but not more than custom
board fixup/copy code which is being deleted (as it is not needed anymore).
Signed-off-by: Pali Rohár <pali@kernel.org>
caam driver model enabled in spl for secure boot.
fsl_rsa_mod_exp driver enabled in spl for validating uboot image.
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
This board is behind on several mandatory DM migrations and is missing
OF_CONTROL support that makes other conversions impossible. Remove it.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This board is behind on several mandatory DM migrations and is missing
OF_CONTROL support that makes other conversions impossible. Remove it.
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Heiko Schocher <hs@denx.de>
This converts the following to Kconfig:
CONFIG_FSL_NGPIXIS
CONFIG_SYS_FSL_QMAN_V3
CONFIG_SYS_FSL_RAID_ENGINE
CONFIG_SYS_FSL_RMU
CONFIG_SYS_FSL_SINGLE_SOURCE_CLK
CONFIG_SYS_FSL_SRIO_LIODN
CONFIG_SYS_FSL_TBCLK_DIV
CONFIG_SYS_FSL_USB1_PHY_ENABLE
CONFIG_SYS_FSL_USB2_PHY_ENABLE
CONFIG_SYS_FSL_USB_DUAL_PHY_ENABLE
CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_FSL_PCIE_COMPAT
To do this, introduce a choice and option for each of the strings used
and set CONFIG_SYS_FSL_PCIE_COMPAT based on that.
Signed-off-by: Tom Rini <trini@konsulko.com>
We can determine which of these we need given CPU_BIG_ENDIAN being
enabled or not, so move that logic to Kconfig from config.mk.
Cc: Alexey Brodkin <alexey.brodkin@synopsys.com>
Cc: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS
CONFIG_SYS_FSL_OTHER_DDR_NUM_CTRLS
And we remove the entries from the README for a number of already
converted items.
Signed-off-by: Tom Rini <trini@konsulko.com>
Update sandbox to include the VBE bootmeth. Update a few existing tests to
take account of this change, specifically that the new bootmeth now
appears when scanning.
Signed-off-by: Simon Glass <sjg@chromium.org>
For most testing we don't want this bootmeth to actually do anything. For
the one test where we do, add a test hook to obtain the correct behaviour.
This will allow us to bind the device always, rather than just doing it
for this test.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rename these to VESA, itself an abbreviation, to avoid a conflict with
Verified Boot for Embedded.
Rename this to avoid referencing VBE.
Signed-off-by: Simon Glass <sjg@chromium.org>
We want to use VBE to mean Verfiied Boot for Embedded in U-Boot. Rename
the existing VBE (Vesa BIOS extensions) to allow this.
Verified Boot for Embedded is documented doc/develop/vbe.rst
Signed-off-by: Simon Glass <sjg@chromium.org>
The booting flow is SPL -> OpenSBI -> U-Boot.
The boot hart may change after OpenSBI and may not always be hart0,
so wrap the related branch instruction with M-MODE.
Current DTB setup for XIP is not valid.
There is no chance for CONFIG_SYS_FDT_BASE, the DTB address used
in XIP mode, to be returned. Fix this.
Fixes: 2e8d2f8843 ("riscv: Remove OF_PRIOR_STAGE from RISC-V boards")
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Restore global pointer before board_init_f_init_reserve call,
as "a0" can be set in harts_early_init call and we end up with
invalid global pointer.
Signed-off-by: Nikita Shubin <n.shubin@yadro.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Replace code that accessed the GPIO registers directly with code that
makes use of the LED_GPIO driver.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Move U-Boot specific device tree property u-boot,dm-pre-reloc into U-Boot
specific device tree include file armada-38x-controlcenterdc-u-boot.dtsi.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Move U-Boot specific device tree property u-boot,dm-pre-reloc into U-Boot
specific device tree include file armada-xp-theadorable-u-boot.dtsi.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Replace it by including of mvebu-u-boot.dtsi file. When board does not use
-u-boot.dtsi then mvebu-u-boot.dtsi is included automatically by makefile
scripts/Makefile.lib.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Set u-boot,dm-pre-reloc for /soc/, /soc/internal-regs/ and &uart0 nodes as
it is required on every 32-bit Armada SoCs. And set also u-boot,dm-pre-reloc
for &spi0 when going to boot from SPI because otherwise SPL SPI drivers do
not load.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
64-bit Armada DTS files are not build correctly during compilation of
32-bit Armada boards and vice versa. So fix makefile build system to
compile only those dts files which are compatible for the current build
(64-bit Armada DTS files only for 64-bit builds and 32-bit Armada DTS files
only for 32-bit builds).
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
BootROM boot method should always work so always add it as fallback method
to spl_boot_list. In case U-Boot SPI driver fails it is better to try using
BootROM than hanging as by default only one boot method is specified.
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
UniPhier LD20, PXs2 and PXs3 boards have ethernet phy that has RX/TX delays
of RGMII interface using pull-ups on the RXDLY and TXDLY pins.
So should set the phy-mode to "rgmii-id" to show that RX/TX delays are
enabled.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
All `sm efuseread/efusewrite` commands exit with an error, even if the fuse
have actually been dealt with correctly.
This is because the smc call return the size it actually processed but this
result is checked against 0.
Return failure in do_efuse_read/write if the return value of
meson_sm_read/write_efuse() is not the requested size.
Fixes: 52195ba5f5 ("ARM: amlogic: add sm efuse write support and cmd for read/write efuse")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20220804144138.33809-1-jbrunet@baylibre.com
This converts the following to Kconfig:
CONFIG_SYS_FSL_CORES_PER_CLUSTER
As part of this, correct the dependencies on SYS_FSL_THREADS_PER_CORE.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_FSL_CCSR_GUR_BE
CONFIG_SYS_FSL_CCSR_SCFG_BE
CONFIG_SYS_FSL_ESDHC_BE
CONFIG_SYS_FSL_IFC_BE
CONFIG_SYS_FSL_PEX_LUT_BE
CONFIG_SYS_FSL_CCSR_GUR_LE
CONFIG_SYS_FSL_CCSR_SCFG_LE
CONFIG_SYS_FSL_ESDHC_LE
CONFIG_SYS_FSL_IFC_LE
CONFIG_SYS_FSL_PEX_LUT_LE
Signed-off-by: Tom Rini <trini@konsulko.com>
If the device is a GP and we detect a signing certificate then remove it.
It would fail to authenticate otherwise as the device is GP and has no
secure authentication services in SYSFW.
This shouldn't happen often as trying to boot signed images on GP devices
doesn't make much sense, but if we run into a signed image we should at
least try to ignore the certificate and boot the image anyway. This could
help with users of GP devices who only have HS images available.
If this does happen, print a nice big warning.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
We can skip the image authentication check at runtime if the device is GP.
This reduces the delta between GP and HS U-Boot builds. End goal is
to re-unify the two build types into one build that can run on all
device types.
Signed-off-by: Andrew Davis <afd@ti.com>
On HS-FS devices signing boot images is optional. To ease use
we check if we are HS-FS and if no certificate is attached
to the image we skip the authentication step with a warning
that this will fail when the device is set to security enforcing.
Signed-off-by: Andrew Davis <afd@ti.com>
K3 SoCs are available in a number of device types such as
GP, HS-FS, EMU, etc. Like OMAP SoCs we can detect this at runtime
and should print this out as part of the SoC information line.
We add this as part of the common.c file as it will be used
to also modify our security state early in the device boot.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
SPL_GPIO_SUPPORT is named SPL_GPIO since commit 83061dbd1c ("Rename
GPIO_SUPPORT to GPIO"), SPL_MMC_SUPPORT is named SPL_MMC since commit
103c5f1806 ("mmc: Rename MMC_SUPPORT to MMC"), SPL_SERIAL_SUPPORT is
named SPL_SERIAL since commit 2a73606668 ("serial: Rename
SERIAL_SUPPORT to SERIAL") so let's select the correct Kconfig options.
Fixes: 8b71576f38 ("mx7ulp_com: add support for SPL")
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
There is a bug in Turris Omnia's schematics, whereupon the MPP[26] pin,
which is routed to CN11 pin header, is documented as SPI CS1, but
MPP[26] pin does not support this function. Instead it controls chip
select 2 if in "spi0" mode.
Fix the name of the pin node in pinctrl node and fix the comment in SPI
node.
Signed-off-by: Marek Behún <kabel@kernel.org>
* Add SPDX-License-Identifier
* Add SFP and LED nodes
* Fix PHY nad NOR nodes
* Remove duplicates from u-boot.dtsi file
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Linux kernel uses compatible string "marvell,armada370-nand-controller" for
nand controllers on Armada 370/XP/38x. U-Boot currently uses mix of
"marvell,armada370-nand" and "marvell,mvebu-pxa3xx-nand".
So unify it and use just Linux kernel compatible string.
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Stefan Roese <sr@denx.de>
QorIQ U-Boot binary for SD card booting compiled during build process
(either u-boot.bin or u-boot-with-spl.bin) cannot be directly loaded by
QorIQ pre-PBL BootROM. Compiled U-Boot binary first needs to be processed
by Freescale boot_format tool as described in doc/README.mpc85xx-sd-spi-boot
BootROM requires that image on SD card must contain special boot sector.
Implement support for generating this special boot sector directly in
U-Boot start code. Boot sector needs to be at the beginning of the image,
so when compiling only proper U-Boot without SPL then it needs to be in
proper U-Boot. When compiling SPL with proper U-Boot then it needs to be
only in SPL.
Support can be enabled by a new config option FSL_PREPBL_ESDHC_BOOT_SECTOR.
Via other two additional options FSL_PREPBL_ESDHC_BOOT_SECTOR_START and
FSL_PREPBL_ESDHC_BOOT_SECTOR_DATA it is possible to tune how final U-Boot
image could be stored on the SD card.
Signed-off-by: Pali Rohár <pali@kernel.org>
This allows U-Boot mvebu-gpio.c driver to switch particular MPP pin into
GPIO mode and enable GPIO support.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
The generic ARM relocate_code function was using its own function entry
point as a relocation base, and it was obtaining that address by using
the "adr" instruction on that entry point label.
However that label is not just an ordinary label, instead we explicitly
mark it as a function start address. Normally that doesn't change much
(other than for debugging), but when assembled in Thumb mode, newer
versions of the GNU assembler prepare everything for this address being
used as the argument to a "bx" call, so make sure bit 0 is set in there
to mark this function as Thumb code. Of course this doesn't end up very
well when we use this address for the ensuing memcpy operation.
To avoid this problem, and to solve it in a robust way, add an extra
label, which is not marked as a function entry, and use that for the adr
instruction. This lets all assemblers generate the right immediate offset
in the "adr" instruction.
This fixes in particular ARMv7-M ports when using GNU binutils v2.37 or
newer (commit d3e52e120b68 seems to trigger the change in behaviour).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reported-by: Jesse Taube <mr.bossman075@gmail.com>
After we switch to use BINMAN_SYMBOLS, there is no need to pad
the file size to 0x8000 and 0x4000. After we use BINMAN_SYMBOLS,
the u-boot-spl-ddr.bin shrink about 36KB with i.MX8MP-EVK.
Tested-by: Tim Harvey <tharvey@gateworks.com> #imx8m[m,n,p]-venice
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
We are migrating to use binman symbols, the current names are
inconsistent across different boards, so unify them.
Also add `type = "blob-ext";`, since the new names are not valid binman
types.
Tested-by: Tim Harvey <tharvey@gateworks.com> #imx8m[m,n,p]-venice
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
[Alper: Edit commit message]
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Set ARM clock to OD frequency 1.7Ghz, since we have set PMIC VDD_SOC
to Overdrive voltage 0.9V
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add the DTSi file and DT header files for i.MX93 SoC
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Since i.MX9 uses same DDR PHY with i.MX8M, split the DDRPHY to a common
directory under imx, then use dedicated ddr controller driver for each
iMX9 and iMX8M.
The DDRPHY registers are space compressed, so it needs conversion to
access the DDRPHY address. Introduce a common PHY address remap function
for both iMX8M and iMX9 for all PHY registers accessing.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Implement the DDR driver clock interfaces for set DDR rate and
bypass DDR PLL
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add bootaux command to support on-demand booting M33 from u-boot.
It kicks M33 via ATF by "bootaux 0x201e0000 0"
Signed-off-by: Peng Fan <peng.fan@nxp.com>
To support on-demand booting M33 image from A core. SPL needs
to follow M33 kick up sequence to release M33 firstly,
then set M33 CPUWAIT signal. ATF will clear CPUWAIT to kick
M33 to run.
The prepare function also works around the M33 TCM ECC issue by
clean the TCM. Also enable sentinel handshake and WDOG1 clock
for M33 stop and reset.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add power init of MEDIAMIX, MLMIX and DDRMIX. And clear isolation
of MIPI DSI/CSI, USBPHY after the power up.
SPL should call the power init in its boot sequence before accessing
above three MIX and USB.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add GPIO registers structure for iMX93, so that we can enable lpgpio
driver
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
i.MX93 fuse can be accessed through FSB and s400-api. Add mapping tables
for i.MX93. The offset address of FSB accessing OTP shadow registers is
different between i.MX8ULP and i.MX93, so use macro to define the offset
address instead of hardcode.
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Update the get chip revision methond to use S400 API, also record
other information like lifecycle and UID to global data.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add TRDC driver to iMX9. The TRDC init splits to two phases:
1. Early init phase will release TRDC from Sentinel and open write
permission to the memory where SPL image runs. Sentinel will set
the memory to RX only after ROM authentication for the OEM
closed part.
2. Init phase will configure TRDC to allow non-secure master to
access DDR. So the peripherals can work in u-boot.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Introduce Sentinel API ahab_release_m33_trout to make sure sentinel
release M33 trout and make sure M33 could boot.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
To support more RDC instances on i.MX93, update API to latest
definition.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Since iMX9 uses S401 which shares the API with iMX8ULP. So move S400
MU driver and API to a common place and selected by CONFIG_IMX_SENTINEL
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
i.MX9 shares same ROM API with i.MX8ULP, so make the i.MX8ULP the function
prototype common and usable by i.MX9.
Also include mmc env functions that use ROM API.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add timer_init to update ARM arch timer with correct frequency
from system counter and enable system counter.
Signed-off-by: Jian Li <jian.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add clock API to support CCM root clock and LPCG setting
Set the CCM AUTHEN register to allow non-secure world to set
root clock and lpcg.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
i.MX8MN/P/ULP supports ROM API, they have almost same get_boot_device
implementation, so move to a common file. And when support i.MX9,
no need to include the other function copy.
Since sys_proto.h is included in imx_romapi.c, there will be build
warning for i.MX8M because wdog_regs not defined, so include imx-regs.h
in i.MX8M sys_proro.h
Signed-off-by: Peng Fan <peng.fan@nxp.com>
For SoCs support ROM API, CONFIG_SPL_BOOTROM_SUPPORT is needed,
so use this macro to guard the code to avoid extend the list.
And drop the guard with structure definition, there is no need.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Move the default mapping of spl_boot_device to weak function of
spl_board_boot_device. So that every board of iMX7/8/8M can overwrite
this function to implement specific mapping.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The SPL SDP is configured as BOOT_DEVICE_BOARD, so when booting from
USB, change its type to BOOT_DEVICE_BOARD, so we can use SDP.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
All the SoCs use mach-imx has CONFIG_MACH_IMX selected, so
the macro could be the gate to build arch/arm/mach-imx to simplify
the rules.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
With supporting timer_get_boot_us, we can profile boot up time with below
configs and function bootstage_mark_name().
CONFIG_BOOTSTAGE=y
CONFIG_BOOTSTAGE_REPORT=y
CONFIG_CMD_BOOTSTAGE=y
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Store a set of supported bitstream types in xilinx_desc structure.
It will be used to determine whether an FPGA image is able to be
loaded with a given driver.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Tested-by: Ricardo Salveti <ricardo@foundries.io>
Tested-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Link: https://lore.kernel.org/r/20220722141614.297383-4-oleksandr.suvorov@foundries.io
Signed-off-by: Michal Simek <michal.simek@amd.com>
Mailbox driver might be need for Versal and other future platforms.
To remove the dependency, move struct zynqmp_ipi_msg to
zynqmp_firmware.h so that mailbox driver compiles for other platforms
easily.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20220722084658.30995-5-ashok.reddy.soma@xilinx.com
With commit ce39ee28ec ("zynqmp: Do not place u-boot to reserved memory
location"), the function board_get_usable_ram_top() is allocating
MMU_SECTION_SIZE of about 2MB using lmb_alloc(). But we dont have this
much memory in case of mini U-Boot.
Keep these functions which use lmb under CONFIG_LMB so that they are
compiled and used only when LMB is enabled.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/75e52def75f573e554a6b177a78504c128cb0c4a.1657183534.git.michal.simek@amd.com
There are no references to CONFIG_SOC_DM355 / CONFIG_SOC_DM365 /
CONFIG_SOC_DM644X / CONFIG_SOC_DM646X and the files these Makefile lines
reference have already been dropped.
Signed-off-by: Tom Rini <trini@konsulko.com>
