replace looking up i2c bus name by bus number and define bus numbers and
eeprom address with #defines.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The intention of commit d714a75fd4 ("imx: replace CONFIG_SECURE_BOOT
with CONFIG_IMX_HAB") was to convert from CONFIG_SECURE_BOOT to
CONFIG_IMX_HAB, but it replaced with an extra "_" character.
Fix it by using the correct CONFIG_IMX_HAB symbol.
Fixes: d714a75fd4 ("imx: replace CONFIG_SECURE_BOOT with CONFIG_IMX_HAB")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
The GW54xx-G revision has the foolowing changes:
- replaces the EOL GbE PHY with an updated part (requires an enable pin)
- replaces the EOL analog video decoder with an updated part
(requires dt prop)
- add power control to miniPCIe socket
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The GW53xx-G revision has the foolowing changes:
- replaces the EOL GbE PHY with an updated part (requires an enable pin)
- replaces the EOL analog video decoder with an updated part
(requires dt prop)
- add power control to miniPCIe socket
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The GW5913 is a Single Board Computer based on the NXP i.MX6Q/DL SoC
with the following features:
- DDR3 DRAM
- NAND FLASH (256MiB or 2048MiB)
- Gateworks System Periperhal Controller
- front panel LED's
- front panel pushbutton
- Digital I/O connector (I2C/GPIO/UART)
- u-blox Zoe-M8Q GPS
- 1x RJ45 GbE
- 1x MiniPCIe socket with PCIe USB 2.0 and nanoSIM socket
- Passive PoE and wide-range DC power supply
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The GW5912 is a Single Board Computer based on the NXP i.MX6Q/DL SoC
with the following features:
- DDR3 DRAM
- NAND FLASH (256MiB or 2048MiB)
- microSD socket
- Gateworks System Periperhal Controller
- front panel LED's
- front panel pushbutton
- RS232 connector (2x UARTs)
- CAN/RS485 connector
- Digital I/O connector (I2C/GPIO)
- SPI connector
- u-blox Zoe-M8Q GPS
- LIS2DE12 Accellerometer
- 1x FEC GbE RJ45 with 802.3at Active PoE
- 1x PCI GbE RJ45 with Passive PoE
- 5x MiniPCIe socket with PCIe/USB 2.0
- 1x MiniPCIe socket with PCIe/USB 2.0 and SIM socket
- Aux power input with wide-range DC power supply
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The GW5910 is a Single Board Computer based on the NXP i.MX6Q/DL SoC
with the following features:
- DDR3 DRAM
- NAND FLASH (256MiB or 2048MiB)
- microSD socket
- Gateworks System Periperhal Controller
- front panel LED's
- front panel pushbutton
- RS232 connector (2x UARTs)
- Digital I/O connector (I2C/GPIO)
- SPI connector
- u-blox Zoe-M8Q GPS
- LIS2DE12 Accellerometer
- TI CC1352 ARM Cortex-M4 multiprotocol sub-1GHz / 2.4GHz wireless MCU
- On-board brcmfmac WiFi and BT module
- RGMII RJ45 GbE
- 1x MiniPCIe socket with PCIe/USB 2.0
- 1x MiniPCIe socket with USB 2.0 and nanoSIM socket
- Passive PoE and wide-range DC power supply
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Move board/revision specific dt fixups for WDOG and UHS-I features
so that we can call them early for U-Boot control dt as well.
Additionally drop a deprected non-mainline dt-prop fixup regarding
HDMI input format.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
EEPROM bits no longer indicate support for NAND so instead use
hard-coded value from board config struct.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Only one dtb is currently supported, so match with imx6-colibri.
Signed-off-by: Ming Liu <ming.liu@toradex.com>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
If config block support is enabled, USB gadget modes unconditionally
use Toradex Product ID as USB PID. Some applications might prefer a
different and/or static USB PID. Add a Kconfig configuration option
to descide whether to use USB PID from config block or the fallback
config option CONFIG_G_DNL_PRODUCT_NUM.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
In case USB serial downloader has been used to load U-Boot start the
serial download protocol (SDP) emulation. This allows to download
complete images such as Toradex Easy Installer over USB SDP as well.
This code uses the boot ROM provided boot information to reliably
detect USB serial downloader.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
The bootparams do not have to be at fixed location, they can be
dynamically mallocated instead. Make it so to get rid of another
fixed assignment.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Biju Das <biju.das.jz@bp.renesas.com>
Cc: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
The main reason for this to be implemented is capsule update.
Two memories are supported and tested which is MMC FAT based and QSPI
based.
For creating capsule these commands are used:
./tools/mkeficapsule --raw spl/boot.bin --index 1 capsule1.bin
./tools/mkeficapsule --raw u-boot.itb --index 2 capsule2.bin
Then transfer to SD card where these commands run:
load mmc 0 10000000 capsule1.bin
efidebug capsule update -v 10000000
load mmc 0 10000000 capsule2.bin
efidebug capsule update -v 10000000
Depends on the boot device used are binaries loaded to qspi or mmc fat
partition.
Also multiboot register is handled to make sure that the same location(id)
is used as image which is upgraded.
Two locations are used by purpose for SPL flow. If only boot.bin is used
create only one capsule.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
When U-Boot runs in EL2 there is no access to csu_base registers that's why
this has to be done via firmware interface to find out multi boot register
value. Till now this function is called only from SPL in EL3.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Change multi_boot() to return multiboot value and move print out of this
function and let this function to be used by other functions without
duplicating message.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
When env_set() is called there is no need to allocate memory for variable
which is already saved that's why free it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
It is a pain to have to specify the value 10 in each call. Add a new
dectoul() function and update the code to use it.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is a pain to have to specify the value 16 in each call. Add a new
hextoul() function and update the code to use it.
Add a proper comment to simple_strtoul() while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
- Move the PSCI runtime code for H3/A23/A33 into SRAM
- Pick the environment from the actual MMC boot device (SD card vs.
eMMC)
- Plus a small improvement from Icenowy, just for good measure.
Currently, the environment is always stored in eMMC if eMMC is enabled
in the config. This means images written to SD and eMMC will cross-
contaminate their environments unless the configuration is changed.
By dropping the device number from the environment location string and
implementing mmc_get_env_dev, we will always use the environment from
the boot device when booting from SD/eMMC.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
In DM Ethernet, the old "egiga0" and 'egiga1" names are no longer valid,
so replace these with Ethernet PHY names from device tree. Also, read
Ethernet PHY address for each port from device tree.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The gdsys a38x config file (controlcenterdc_defconfig) uses BootROM to
load U-Boot proper.
Since it is now possible to do this via U-Boot SPL framework, we do not
need to provide custom spl_board_init() which calls return_to_bootrom().
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Now that proper load and execution addresses are set in v1 kwbimage we
can use it for loading and booting U-Boot proper.
Use the new spl_parse_board_header() function to implement parsing the
kwbimage v1 header. Use information from this header to locate offset and
size of the U-Boot proper binary, instead of using the legacy U-Boot
header which is prepended to the U-Boot proper binary stored at fixed
offset. This has the advantage that we do not need to relay on legacy
U-Boot header anymore and therefore U-Boot proper binary can be stored at
any offset, as is the case when loading & booting U-Boot proper by
BootROM. The CONFIG_SYS_U_BOOT_OFFS option is therefore not used by SPL
code anymore.
Also allow to compile U-Boot SPL without CONFIG_SPL_SPI_FLASH_SUPPORT,
CONFIG_SPL_MMC_SUPPORT or CONFIG_SPL_SATA_SUPPORT set. In this case
BootROM is used for loading and executing U-Boot proper. This reduces the
size of U-Boot's SPL image. By default these config options are enabled
and so BootROM loading is not used. In some cases BootROM reads from SPI
NOR at lower speed than U-Boot SPL. So people can decide whether they
want to have smaller SPL binary at the cost of slower boot.
Therefore dependency on CONFIG_SPL_DM_SPI, CONFIG_SPL_SPI_FLASH_SUPPORT,
CONFIG_SPL_SPI_LOAD, CONFIG_SPL_SPI_SUPPORT, CONFIG_SPL_DM_GPIO,
CONFIG_SPL_DM_MMC, CONFIG_SPL_GPIO_SUPPORT, CONFIG_SPL_LIBDISK_SUPPORT,
CONFIG_SPL_MMC_SUPPORT, CONFIG_SPL_SATA_SUPPORT and
CONFIG_SPL_LIBDISK_SUPPORT is changed from strict to related "imply"
(which can be selectivelly turned off and causes booting via BootROM).
Options CONFIG_SYS_SPI_U_BOOT_OFFS,
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR and
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_DATA_PART_OFFSET have to to be set to
zero as they define the location where kwbimage header starts. It is the
location where BootROM expects start of the kwbimage from which it reads,
parses and executes SPL part. The same applies to option
CONFIG_SPL_SATA_RAW_U_BOOT_SECTOR, which has to be set to one.
Update all config files to set correct values of these options and set
CONFIG_SYS_U_BOOT_OFFS to the correct value - the offset where U-Boot
proper starts.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
The PADCONFIG_202 register (0x02621328) is affected by the locking
of the RSTMUX8 register (0x02620328), and so cannot be configured
in kernel. This has been confirmed as a hardware bug and affects
all K2G SoCs.
Setup the pinmux for this pin before locking the RSTMUX8 register
to allow the ICSS1 PRU1 Ethernet PHY port to work properly. The
workaround was added only for the K2G-ICE board to configure the
pins needed for the PRUSS Ethernet usecase.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210726232248.24395-1-s-anna@ti.com
Align reset_cpu function with the next prototypes in
sysreset.h or in cpu_func.h to solve compilation issue:
void reset_cpu(void);
This patch solves the prototype conflict when cpu_func.h is
included.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Rename these options so that CONFIG_IS_ENABLED can be used with them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
It is quite confusing that CONFIG_SYS_I2C selects the legacy I2C and
CONFIG_DM_I2C selects the current I2C. The deadline to migrate I2C is less
than a year away.
Also we want to have a CONFIG_I2C for U-Boot proper just like we have
CONFIG_SPL_I2C for SPL, so we can simplify the Makefile rules.
Rename this symbol so it is clear it is going away.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Rename this option so that CONFIG_IS_ENABLED can be used with it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
need return -1 if boot source is not EMMC or SD ( for example it will be
useful if we have multy env sources configuration and device was booted
from SPI flash and env need read from SPI not from mmc )
Signed-off-by: Artem Lapkin <art@khadas.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
When a push-button is released and PA13/PA14 are defined as input (high-Z)
the LED should not be active as the circuit is open but a small current
leak through PCB or push-button close the circuit and allows a small LED
bias giving erroneous level voltage.
So it is recommended to activate an internal pull-up in order to clearly
fix the voltage at PA13/PA14 when button is released and to wait
a short delay before to read the GPIO value only when the pull-up is
correctly configured.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Move j721e document from board/ti/j721e/README to
doc/board/ti/j721e_evm.rst after converting it to RST format.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210721155849.20994-20-kishon@ti.com
Add support for probing and configuring Torrent serdes on J7200.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210721155849.20994-11-kishon@ti.com
This device tree is imported from Linux 5.13.1 and enabled via the
am335x board file and the am335x evm defconfig.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
Add a bus driver for this and use it to configure the bus parameters for
the Ethernet interface. Drop the old pre-driver-model code.
Switch over to use driver model for Ethernet.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The SPL can also be compiled with sysreset drivers just fine, so
update the condition to cater for that option.
The same change was done by commit efa1a62ad2 ("ARM: imx8m: Do not define
do_reset() if sysreset is enabled").
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The system refuses to boot without any environment, so return ENVL_NOWHERE when
there's nowhere to store the environment instead of ENVL_UNKNOWN.
This fixes that the board won't boot from eMMC when CONFIG_ENV_IS_IN_FAT is not
defined, for example. Similar for other combinations.
Fixes: 1025bd098a "xilinx: zynqmp: Add support for saving variables"
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Split arasan_zynqmp_set_tapdelay() to handle input and output tapdelays
separately. This is required to handle zero values for ITAP and OTAP
values. If we dont split, we will have to remove the if() in the
function, which makes ITAP values to be overwritten when OTAP values are
called to set and vice-versa.
Restrict tap_delay value calculated to max allowed 8 bits for ITAP and 6
bits for OTAP for ZynqMP.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
At the moment pressing the volume down key does not actually launch
fastboot. This is because setting "bootdelay" to "-1" actually
disables autoboot and drops to the U-Boot console. It does not execute
the "bootcmd".
The correct value for "bootdelay" here would be "-2", which disables
the delay and key checking and would immediately execute the "bootcmd".
However, even better in this case is using "preboot" to trigger Fastboot.
The advantage is that running "fastboot continue" will actually continue
the autoboot process instead of ending up in the U-Boot shell.
Also make sure to unset "preboot" again immediately in case the user
saves the environment after triggering fastboot.
Cc: Ramon Fried <rfried.dev@gmail.com>
Fixes: aa043ee91a ("db410c: automatically launch fastboot")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
At the moment the U-Boot port for the DragonBoard 410c is designed
to be loaded as an Android boot image after Qualcomm's Little Kernel (LK)
bootloader. This is simple to set up but LK is redundant in this case,
since everything done by LK can be also done directly by U-Boot.
Dropping LK entirely has at least the following advantages:
- Easier installation/board code (no need for Android boot images)
- (Slightly) faster boot
- Boot directly in 64-bit without a round trip to 32-bit for LK
So far this was not possible yet because of unsolved problems:
1. Signing tool: The firmware expects a "signed" ELF image with extra
(Qualcomm-specific) ELF headers, usually used for secure boot.
The DragonBoard 410c does not have secure boot by default but the
extra ELF headers are still required.
2. PSCI bug: There seems to be a bug in the PSCI implementation
(part of the TrustZone/tz firmware) that causes all other CPU cores
to be started in 32-bit mode if LK is missing in the boot chain.
This causes Linux to hang early during boot.
There is a solution for both problems now:
1. qtestsign (https://github.com/msm8916-mainline/qtestsign)
can be used as a "signing" tool for U-Boot and other firmware.
2. A workaround for the "PSCI bug" is to execute the TZ syscall when
entering U-Boot. That way PSCI is made aware of the 64-bit switch
and starts all other CPU cores in 64-bit mode as well.
Simplify the dragonboard410c board by removing all the extra code that
is only used to build an Android boot image that can be loaded by LK.
This allows dropping the custom linker script, special image magic,
as well as most of the special build/installation instructions.
CONFIG_REMAKE_ELF is used to build a new ELF image that has both U-Boot
and the appended DTB combined. The resulting u-boot.elf can then be
passed to the "signing" tool (e.g. qtestsign).
The PSCI workaround is placed in the "boot0" hook that is enabled
with CONFIG_ENABLE_ARM_SOC_BOOT0_HOOK. The extra check for EL1 allows
compatibility with custom firmware that enters U-Boot in EL2 or EL3,
e.g. qhypstub (https://github.com/msm8916-mainline/qhypstub).
As a first step these changes apply only to DragonBoard410c.
Similar changes could likely also work for the DragonBoard 820c.
Note that removing LK wouldn't be possible that easily without a lot of
work already done three years ago by Ramon Fried. A lot of missing
initialization, pinctrl etc was already added back then even though
it was not strictly needed yet.
Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Since the SCBM SMMU is not only connected to the NETSEC
but also shared with the F_SDH30 (eMMC controller), that
should be initialized at board level instead of NETSEC.
Move the SMMU initialization code into board support
and call it from board_init().
Without this fix, if the NETSEC is disabled, the Linux
eMMC ADMA cause an error because SMMU is not initialized.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Ensure USB hub, PCIe-USB bridge, and ULPI device to be reset
even if the rebooting is without power-cycling.
Signed-off-by: Vincent Chen <vincent.chen@sifive.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Create a new function spl_reset_device_by_gpio to reset the device
whose reset pin is connected to the GPIO. Then, using this function
to initialize GEMGXL.
Signed-off-by: Vincent Chen <vincent.chen@sifive.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
This patch reverts the following commits:
- 4b4159d0f3 ("riscv: dts: add dts for unmatched rev1")
- ffe9a394df ("board: sifive: support spl multi-dtb on unmatched board")
We won't plan to support unmatched that the revision below 3 in u-boot,
so they can be dropped because they might be useless.
Changed in v2:
- rebase codebase to the latest master branch
Signed-off-by: Zong Li <zong.li@sifive.com>
Suggested-by: David Abdurachmanov <david.abdurachmanov@sifive.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
We wouldn't like to allow user to change the serial number, so remove
the command for changing serial number in EEPROM.
Signed-off-by: Zong Li <zong.li@sifive.com>
Suggested-by: David Abdurachmanov <david.abdurachmanov@sifive.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
lx2160ardb Rev-C board has i2c node for thermal monitors
connected to different chip offset.
Add device tree fixup to use lx2160ardb dts and apply
thermal node fixups for lx2160ardb Rev-C board.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
[sp:thernal->thermal]
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Updates the board configuration to enable use of the PCA9547 I2C mux.
Signed-off-by: Stephen Carlson <stcarlso@linux.microsoft.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Updates the board configuration to enable use of the PCA9547 I2C mux.
Signed-off-by: Stephen Carlson <stcarlso@linux.microsoft.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Updates the board configuration to enable use of the PCA9547 I2C mux.
Signed-off-by: Stephen Carlson <stcarlso@linux.microsoft.com>
[Squashed ls2088a patch to fix compilation]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Updates the board configuration to enable use of the PCA9547 I2C mux.
Signed-off-by: Stephen Carlson <stcarlso@linux.microsoft.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Updates the board configuration to enable use of the PCA9547 I2C mux.
Signed-off-by: Stephen Carlson <stcarlso@linux.microsoft.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Updates the board configuration to enable use of the PCA9547 I2C mux.
Signed-off-by: Stephen Carlson <stcarlso@linux.microsoft.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Updates the board configuration to enable use of the PCA9547 I2C mux.
Signed-off-by: Stephen Carlson <stcarlso@linux.microsoft.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Refactors similar mux code from multiple NXP boards into a common location,
and allows it to be disabled in config.
New config: CONFIG_FSL_USE_PCA9547_MUX to enable PCA9547 mux functionality.
Signed-off-by: Stephen Carlson <stcarlso@linux.microsoft.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
- Marvell SheevaPlug: Convert Ethernet and SATA to Driver Model (Tony)
- Zyxel NSA310S NAS: Convert to Driver Model (Tony)
- Turris_omnia: Add `u-boot-env` NOR partition (Marek)
- Turris_omnia: Fixup MTD partitions in Linux' DTB (Marek)
- Espressobin: Enable 'mtd' command and define SPI NOR partitions (Pali)
- Enabled distro boot for all TI platforms.
- Cleanup for AM335x Guardian Board
- PRUSS rproc on AM65 platform.
- Add PMIC support for J7200
- Misc fixes for Nokia RX-51
# Conflicts:
# arch/arm/mach-omap2/am33xx/Kconfig
Fixup SPI NOR partition nodes in Linux' device tree prior booting Linux.
Linux' devicetree does not contain "u-boot-env" partition and we do not
want to add it there because the address is different between stock
U-Boot and current upstream U-Boot.
Instead we add code that recreates partition nodes from scratch
according to how U-Boot sees them (which is defined in U-Boot's device
tree).
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
- In DM Ethernet, the old "egiga0" name is no longer valid, so replace it
with Ethernet PHY name from device tree. Also, Ethernet PHY address
is available so read it from device tree.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
In DM Ethernet, the old "egiga0" name is no longer valid, so replace it
with Ethernet PHY name from device tree. Also, Ethernet PHY address
is available so read it from device tree.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
As the deadline for migration to DM_USB, when using a USB host
controller has now gone two years past the deadline, enforce migration.
This is done by:
- Ensuring that all host controller options (other than the very legacy
old MUSB ones) now select USB_HOST. USB_HOST now enforces DM_USB and
OF_CONTROL.
- Remove other parts of Kconfig logic that had platforms pick DM_USB.
- To keep Kconfig happy, have some select statements test for USB_HOST
as well.
- Re-order some Kconfig entries and menus so that we can cleanly pick
host or gadget roles. For the various HCD options that have platform
glue options, group them together and update dependencies in some
cases.
- As SPL_DM_USB is not required, on platforms that had not yet enabled
it, disable it.
Cc: Marek Vasut <marex@denx.de>
Cc: Icenowy Zheng <icenowy@aosc.io>
Cc: Samuel Holland <samuel@sholland.org>
Cc: FUKAUMI Naoki <naobsd@gmail.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
As the logic here is only used when we have a USB host controller, test
on CONFIG_USB_HOST rather than CONFIG_USB in general. This lets us move
towards using CONFIG_USB only as a menu symbol to say that we have some
form of USB, and then USB_HOST or USB_GADGET depending on the role that
USB plays within the build.
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it. As this is also the last in family remove the related
support as well.
Cc: Angelo Durgehello <angelo.dureghello@timesys.com>
Cc: TsiChung Liew <Tsi-Chung.Liew@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it. As this is also the last in family remove the related
support as well.
Cc: Angelo Durgehello <angelo.dureghello@timesys.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Angelo Durgehello <angelo.dureghello@timesys.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Angelo Durgehello <angelo.dureghello@timesys.com>
Cc: TsiChung Liew <Tsi-Chung.Liew@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
- mips: malta: convert to PCI DM and ETH DM
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEiQkHUH+J02LLC9InKPlOlyTyXBgFAmD0dbMACgkQKPlOlyTy
XBgxOBAAulyJqvTHDWIk6l6d8qseSBgWuwPf0mE/YDKowGrfLbiCWEJICvg3qeJZ
tkIuT5/y2DCjRpKQ2i1GtgTtG2+7AzEMR9FuSys1NMXXyNiLrPdoXKvR/2sDv7F4
V0UPhhaOPNTHObnKea9+x8Kb+fYhT8RrfPvnm55OTeTXpk/jKWUfH+LhQ6ij2lRp
NXnbo5byDyxznn9c5VTT3urMmsXLQdoqiHGfa52+1Zn0TH5AvAHTTQNx4V1bzsKx
z5vG4a5D9Ul52drxhWLgIwSEdwHc08oXA0G7dKnCT8fdZrONqH2QJ2CWQ1AhPQou
Vb+J5fS69N5vJcNRXIHBTQr9R092HT1onV6xCgoy+W7hP0jJuFd8lf0Qs+TKwbxC
t0SdRwXO3AUirejwBtJVfUCtdTQFFtulPIvJLCgLnqIwCzer7rVcLdlpWBaBen3M
VEKFe9mrjYBdVnZiatxMffcplAkIzXturhXSlhE3vqJo3eJ/QPMJL4fnX9MWH8cc
kKFGF1qILI+34mTR2lw+QOJzNehHr+Jre6QzuXUhCCW8APi6CTQeOR/7KqOfTDvH
jZFO9tuOA3W5yQ0sLWmeD1SB+nGI+oQSebe1/ly9aPcYYNlp0w8drKcyUpMaqJ+U
IhwEHszQesZCMkkhccBhtl9pgnfKoD0m0RAdlcFbD67VyPFQKxA=
=wDfz
-----END PGP SIGNATURE-----
Merge tag 'mips-pull-2021-07-18' of https://source.denx.de/u-boot/custodians/u-boot-mips
- mips: gardena-smart-gateway: adjust config to new production values
- mips: malta: convert to PCI DM and ETH DM
As almost all peripherals are connected via PCI dependent on the
used core card, PCI setup is always required. Thus run pci_init()
including PCI scanning and probing and core card specific setups
in board_early_init_r().
Also prepare support for dynamically managing the status of the
different PCI DT nodes dependent on used core card via option
CONFIG_OF_BOARD_FIXUP. Before this feature can be enabled,
the call order of the fix_fdt() init hook in board_init_f
needs to be changed. Otherwise rw_fdt_blob points to a read-only
NOR flash address. Thus this options needs to stay disabled
until the board_init_f problem could be solved. This breaks
running the default U-Boot image on real HW using the FPGA core
card but Qemu emulation still works. Currently Qemu is more
important as MIPS CI tests depend on Malta and the deadline
for PCI DM conversion will be enforced soon.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
The capsule signature is now part of our DTB. This is problematic when a
user is allowed to change/fixup that DTB from U-Boots command line since he
can overwrite the signature as well.
So Instead of adding the key on the DTB, embed it in the u-boot binary it
self as part of it's .rodata. This assumes that the U-Boot binary we load
is authenticated by a previous boot stage loader.
Reviewed-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Tested-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Tested-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Setup USB clock in board codes, and enable the DWC3 XHCI and
PHY drivers to make USB3.0 host port working on i.MX8MQ EVK.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Patrick Wildt <patrick@blueri.se>
Use the device sequence number in boot_instance variable
and no more the SDMMC instance provided by ROM code/TF-A.
After this patch we don't need to define the mmc alias in
device tree, for example:
mmc0 = &sdmmc1;
mmc1 = &sdmmc2;
mmc2 = &sdmmc3;
to have a correct mapping between the ROM code boot device =
"${boot_device}${boot_instance}" and the MMC device in U-Boot.
With this patch the 'mmc0' device (used in mmc commands) is
always used when only one instance sdmmc is activated in device
tree, even if it is only the sdmmc2 or sdmmc3.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Enable U-Boot bootz command and update env scripts to try loading also
zImage file and to try booting via bootz command.
Update also lowlevel_init.S code for checking validity of zImage magic to
correctly relocate kernel in zImage format.
This change allows U-Boot to directly boot Linux kernel without need for
converting kernel image into U-Boot uImage format.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210618132704.32066-1-pali@kernel.org
Use VENDOR_COREBOOT instead of TARGET_COREBOOT so we can have multiple
coreboot boards, sharing options. Only SYS_CONFIG_NAME needs to be
defined TARGET_COREBOOT.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Set up coral so that it can boot from coreboot, even though it is a
bare-metal build. This helps with testing since the same image can be used
in both cases.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The BIOS version may not be present, e.g. on a Chrome OS build. Add the
BIOS date as well, so we get some sort of indication of coreboot's
vintage.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a new 'quiet' argument to mmc_get_op_cond() function which avoids
printing error message when SD/eMMC card is not detected.
Espressobin and mx6cuboxi boards use this function for detecting presence
of eMMC and therefore it is expected and normal that eMMC does not have to
be connected. So error message "Card did not respond to voltage select!"
should be skipped in this case as it is not an error.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Use function mmc_get_op_cond() instead of mmc_init() for detecting presence
of eMMC. Documentation for this function says that it could be used to
detect the presence of SD/eMMC when no card detect logic is available.
This function is also used by mx6cuboxi board for detecting presence of eMMC.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Ensure that 'env default -a' always set correct value to $fdtfile, even
when custom user variable is already stored in non-volatile env storage
(means that env_get("fdtfile") call returns non-NULL value).
As default value is now correctly set like if specified at compile time in
CONFIG_EXTRA_ENV_SETTINGS, there is no need to set $fdtfile explicitly via
env_set("fdtfile", ...) call.
So remove wrong skip based on env_get("fdtfile") and then also unneeded
env_set("fdtfile", ...) call.
Fixes: c4df0f6f31 ("arm: mvebu: Espressobin: Set default value for $fdtfile env variable")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
The U-Boot "stemmy" board is mainly intended to simplify booting
mainline Linux on various smartphones from Samsung based on ST-Ericsson
Ux500. While the mainline kernel is working great, there are still some
features missing there. In particular, it is currently not possible to
charge the battery when using the mainline kernel.
This means that it is still necessary to boot the downstream/vendor
kernel from Samsung sometimes to charge the device. That kernel is
ancient, still uses board files + ATAGS instead of device trees and
relies on a strange very long kernel command line hardcoded in the
Samsung bootloader.
Actually, since mainline is booted with device trees there is a very
simple way to make the old downstream kernel work as well: We can
simply take most of the ATAGS passed to U-Boot from the Samsung
bootloader and copy them as-is when booting a kernel without device
tree. That way the long command line and other needed ATAGS are copied
as-is without having to bother with them.
The only exception is the ATAG_INITRD - since the initrd is loaded
by U-Boot, the atag for that should be generated in U-Boot so it points
to the correct address. All other ATAGS are copied as-is and not
generated in U-Boot.
Also use the chance and provide a serial# for U-Boot by parsing the
ATAG_SERIAL that is also passed by the Samsung bootloader.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
At the moment the "stemmy" board attempts to detect the RAM size with
a simple memory test (get_ram_size()). Unfortunately, this does not work
correctly for devices with 768 MiB RAM (e.g. Samsung Galaxy Ace 2
(GT-I8160), "codina"). Reading/writing memory after the 768 MiB RAM
succeeds but actually overwrites some earlier parts of the memory.
For U-Boot this does not result in any major problems, but on Linux
this will eventually lead to strange crashes because of the memory
corruption.
Since the "stemmy" U-Boot port is designed to be chainloaded from
the original Samsung bootloader, the most reliable way to get the
available amount of RAM is to look at the ATAGS passed by the Samsung
bootloader. Fortunately, the header used to generate ATAGS in U-Boot
(asm/setup.h) can also be easily used to parse them.
Also clarify and simplify stemmy.h a bit to make it more clear where
some of the magic values in there are actually coming from.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
The default implementation of checkboard() calls the
nxp_board_rev_string() function
to retrieve a character representing the revision number of the board.
However, this
attempt to retrieve the revision number may fail in certain situations or be
otherwise undesirable.
There is already a configuration option to avoid retrieving the
revision number of
the board: CONFIG_NXP_BOARD_REVISION. In fact, if this option is enabled, the
nxp_board_rev_string() function's definition will be omitted entirely,
meaning that the previous implementation of checkboard() would result
in a linker error.
This changeset makes the default implementation of checkboard() respect the
CONFIG_NXP_BOARD_REVISION configuration option, only attempting to retrieve
the board revision number if that option is defined.
Signed-off-by: Cody Gray <cody@codygray.com>
The Gateworks System Controller thermal protection feature will disable
the board primary power supply if the on-board temperature sensor
reaches 86C. In many cases this could occur before the temperature
critical components such as CPU, DRAM, eMMC, and power supplies have
reached their max temperature.
Remove the forced re-enable of thermal protection so that users can
knowingly disable it.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The Gateworks GW7901 is an ARM based single board computer (SBC)
featuring:
- i.MX8M Mini SoC
- LPDDR4 DRAM
- eMMC FLASH
- SPI FRAM
- Gateworks System Controller (GSC)
- Atmel ATECC Crypto Authentication
- USB 2.0
- Microchip GbE Switch
- Multiple multi-protocol RS232/RS485/RS422 Serial ports
- onboard 802.11ac WiFi / BT
- microSD socket
- miniPCIe socket with PCIe, USB 2.0 and dual SIM sockets
- Wide range DC power input
- 802.3at PoE
To add support for this board:
- add dts from Linux (accepted for v5.14)
- add SPL PMIC config
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Increase VDD_ARM to prevent timing issues as VDD_SOC is
used in OD mode. Also increase GIC clock.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Enable support for the fec ethernet on phyCORE-i.MX8MP.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
With the first redesign the debug UART had changed from
UART2 to UART1.
As the first hardware revision is considered as alpha and
will not be supported in future. The old setup will not
be preserved.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
If reset-gpio is defined by device-tree use that if
CONFIG_PCIE_IMX_PERST_GPIO is not defined.
Note that after this the following boards which define
CONFIG_PCIE_IMX_PERST_GPIO in their board header file as well as their
device-tree should be able to remove CONFIG_PCIE_IMX_PERST_GPIO without
consequence:
- mx6sabresd
- mx6sxsabresd
- novena
- tbs2910
- vining_2000
Note that the ge_bx50v3 board uses CONFIG_PCIE_IMX_PERST_GPIO and does
not have reset-gpios defined it it's pcie node in the dt thus removing
CONFIG_PCIE_IMX_PERST_GPIO globally can't be done until that board adds
reset-gpios.
Cc: Ian Ray <ian.ray@ge.com> (maintainer:GE BX50V3 BOARD)
Cc: Sebastian Reichel <sebastian.reichel@collabora.com> (maintainer:GE BX50V3 BOARD)
Cc: Fabio Estevam <festevam@gmail.com> (maintainer:MX6SABRESD BOARD)
Cc: Marek Vasut <marex@denx.de> (maintainer:NOVENA BOARD)
Cc: Soeren Moch <smoch@web.de> (maintainer:TBS2910 BOARD)
Cc: Silvio Fricke <open-source@softing.de> (maintainer:VINING_2000 BOARD)
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Add LVDS support for DLC0700XDP21LF 7in 1024x600 display
(equivalent to the DLC-700JMGT4 with new touch controller)
Signed-off-by: Robert Jones <rjones@gateworks.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
In the default pulse-skipping mode regulators that are very lightly
loaded can fail to regulate properly. Switching them to always use
continuous mode causes only around 10mW of overall system power
difference in a lightly loaded system that isn't already operating
them in continuous mode.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
In the default 'auto' mode regulators that are very lightly loaded
can be put in PFM mode and fail to regulator properly. Switching them
to always use continuous PWM mode has a neglibable affect on system
power and garuntees proper regulation under lightly loaded circumstances.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Substitutions in EOL parts changes the VDD_2P5 voltage rail such that
the previously unused VGEN6 LDO is needed in place of the lower power
VGEN5 for the GW54xx-G.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Aside from the usual fixes and updates one visible change is the
MMC update, which fixes some lingering bugs and gives a decent speed
increase on some boards (9->19 MB/s on H6, 21->43 MB/s on A64 eMMC).
I am keeping an watchful eye on bug reports here, to spot any correctness
regressions.
Another change is finally the enablement of the first USB host port on
many boards without micro-USB (data) sockets, like the Pine64 family.
That doubles the number of usable USB ports from 1 to 2 on those boards.
Some smaller fixes, 4GB DRAM support (on the H616) and a new board (ZeroPi)
conclude this first round of changes.
Compile-tested for all 157 sunxi boards, boot-tested on Pine H64,
Pine64-LTS, OrangePi Zero 2 and BananaPi M2 Berry.
Summary:
- DT update for H3/H5/H6
- Enable first USB port on boards without micro-USB
- ZeroPi board support
- 4GB DRAM support for H616 boards
- MMC fixes and speed improvement
- some fixes
We hardcode the pinctrl setting for the MMC controllers in boards.c,
since we need them also in the SPL, where there is no DT yet.
Add the respective setting for the H616 SoC, to enable eMMC on boards
with this SoC as well.
Also to make diagnosing this problem easier, print a warning if a board
tries to setup MMC2 pins without a respective SoC setting being defined.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan at amarulasolutions.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec at siol.net>
ZeroPi is a new board of high performance with low cost
designed by FriendlyElec., using the Allwinner H3 SOC.
ZeroPi features
- Allwinner H3, Quad-core Cortex-A7@1.2GHz
- 256MB/512MB DDR3 RAM
- microsd slot
- 10/100/1000Mbps Ethernet
- Debug Serial Port
- DC 5V/2A power-supply
Signed-off-by: Yu-Tung Chang <mtwget@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The cavium,bdk node is a non-standard dt node used by the BDK and
therefore it is removed from the dt before booting Linux. Do not
require this node to exist as it won't for standard dt's.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Stefan Roese <sr@denx.de>
While this platform has not yet been converted, there is active efforts
to do so. Keep the platform for now.
This reverts commit aa697e6904.
Signed-off-by: Tom Rini <trini@konsulko.com>
If MUSB support is disabled, these parts of the code will fail to build.
Cc: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove them. As this is
the last of the SPEAr platforms, so remove the rest of the remaining
support as well.
Cc: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove them. As this is
also the last SPEAR3XX platform, remove that symbol as well.
Cc: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove them.
Cc: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove them.
Cc: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove it
Cc: Gerald Kerma <dreagle@doukki.net>
Cc: Tony Dinh <mibodhi@gmail.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove it
Cc: Ajay Bhargav <contact@8051projects.net>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove it.
This is also the last PL010_SERIAL using board, so remove those
references.
Cc: Sergey Kostanbaev <sergey.kostanbaev@fairwaves.ru>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove them.
Cc: Andreas Bießmann <andreas@biessmann.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it. As this is the last
ARCH_T4160 platform, remove that support as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove them.
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it.
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it. As this is the last
ARCH_MPC8315 platform, remove that support as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it. This is also the last
of the ARCH_MPC8641/MPC8610 platforms, so remove that support as well.
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
These boards have not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove them. As this includes
the last ARCH_MPC8572 platform, remove that as well.
Cc: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Peter Tyser <ptyser@xes-inc.com>
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it.
Cc: Valentin Longchamp <valentin.longchamp@hitachi-powergrids.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it. As this is the last
ARCH_MPC8568 platform, remove that support as well.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_PCI by the deadline
and is also missing conversion to CONFIG_DM. Remove them. As this is
the only ARCH_T1023 platform left, remove that support as well.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove them. As this is the only
ARCH_MPC8555 platform left, remove that support as well.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it. As this is the only
MPC8541 target left, remove that architecture support as well.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it.
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_PCI by the deadline and are
also missing conversion to CONFIG_DM. Remove them.
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_PCI by the deadline
and is also missing conversion to CONFIG_DM. Remove them.
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_PCI by the deadline.
Remove it.
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Heiko Schocher <hs@denx.de>
This board has not been converted to CONFIG_DM_PCI by the deadline.
Remove it.
Cc: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These board has not been converted to CONFIG_DM_PCI by the deadline.
Remove them. As this is the last of the mcf547x_8x family of boards,
remove that support as well.
Cc: TsiChung Liew <Tsi-Chung.Liew@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These board has not been converted to CONFIG_DM_PCI by the deadline.
Remove them. As this is all of the CONFIG_M548x platforms as well,
remove that code.
Cc: TsiChung Liew <Tsi-Chung.Liew@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
When we do not have bootstage enabled, rather than include an empty
dummy function, we just don't reference it. This saves us space in some
tight builds. This also shows a few cases where show_boot_progress was
incorrectly guarded before.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
The board code here references the display_width / display_height
variables set in the video driver, declare these as externs as gcc-11
will notice and lead to a multiple definition error.
Signed-off-by: Tom Rini <trini@konsulko.com>
In some board cpld.h files the definition of the cpld_data struct
not-quite makes a typedef for cpld_data_t. This problem is caught with
gcc-11 as a multiple definition error. As there are no users of this
non-typedef, fix this by not declaring it one to begin with.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Previous device tree for OpenPiton emits a warning during compilation.
This commit fixes the previous warning adds dts to the OpenPiton RISC-V
board and added the device tree to MAINTAINER file.
Signed-off-by: Tianrui Wei <tianrui-wei@outlook.com>
Reported-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
- mpc8379erdb DM_USB, DM_PCI and DM_ETH support.
- Drop PCI support from the integrator family of boards
- Add synquacer support
- Assorted lpc32xx updates and improvements
- snapdragon (and related) fixes, Broadcom iproc update
Enable a DMed i2c driver for the ea-lpc3250devkitv2 board.
Include some sample commands/output for testing.
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
Add basic support for running U-Boot on the Embedded Artists LPC3250
Developer's Kit v2 board by launching U-Boot from the board's s1l loader
(which comes pre-installed on the board).
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
There's nothing special or unique to the lpc32xx that requires its own config
parameter for specifying the console uart index. Therefore instead of using
the lpc32xx-specific CONFIG_SYS_LPC32XX_UART include parameter, use the
already-available CONFIG_CONS_INDEX from Kconfig.
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add the DeveloperBox 96boards EE support. This board is also
known as Socionext SynQuacer E-Series. It contians one "SC2A11"
SoC, which has 24-cores of arm Cortex-A53, and 4 DDR3 slots,
3 PCIe slots (1 4x port and 2 1x ports which are expanded via
PCIe bridge chip), 2 USB 3.0 ports and 2 USB 2.0 ports, 2 SATA
ports and 1 GbE, 64MB NOR flash and 8GB eMMC on standard
MicroATX Form Factor.
For more information, see this page;
https://www.96boards.org/product/developerbox/
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
We didn't convert the Integrator to use DM for PCI in
time, and we don't use it either so let's just drop
PCI support from the Integrator.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
There are two revisions of unmatched board with different DDR timing,
we'd like to support multi-dtb mechanism in SPL, then it selects the
right DTB at runtime according to PCB revision in I2C EEPROM.
Signed-off-by: Zong Li <zong.li@sifive.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
There are different DDR parameter settings for different board
revisions. Add a new interface to get the PCB revision to determine
which DT should be selected at runtime.
Signed-off-by: Zong Li <zong.li@sifive.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Add initial support for the PCB description EEPROM for SiFive HiFive
Unmatched boards.
This implementation is refactored based on Paul Walmsley's porting and
adopt the suggestions from David Abdurachmanov.
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: David Abdurachmanov <david.abdurachmanov@sifive.com>
Signed-off-by: Zong Li <zong.li@sifive.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
This patch adds openpiton-riscv64 SOC support. In particular, this
board supports a standard bootflow through zsbl->u-boot SPL->
opensbi->u-boot proper->Linux. There are separate defconfigs for
building u-boot SPL and u-boot proper
Signed-off-by: Tianrui Wei <tianrui-wei@outlook.com>
Signed-off-by: Jonathan Balkind <jbalkind@ucsb.edu>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
clk:
- Add driver for Xilinx Clocking Wizard IP
fdt:
- Also record architecture in /fit-images
net:
- Fix plat/priv data handling in axi emac
- Add support for 10G/25G speeds
pca953x:
- Add missing dependency on i2c
serial:
- Fix dependencies for DEBUG uart for pl010/pl011
- Add setconfig option for cadence serial driver
watchdog:
- Add cadence wdt expire now function
zynq:
- Update DT bindings to reflect the latest state and descriptions
zynqmp:
- Update DT bindings to reflect the latest state and descriptions
- SPL: Add support for ECC DRAM initialization
- Fix R5 core 1 handling logic
- Enable firmware driver for mini configurations
- Enable secure boot, regulators, wdt
- Add support xck devices and 67dr
- Add psu init for sm/smk-k26 SOMs
- Add handling for MMC seq number via mmc_get_env_dev()
- Handle reserved memory locations
- Add support for u-boot.itb generation for secure OS
- Handle BL32 handoffs for secure OS
- Add support for 64bit addresses for u-boot.its generation
- Change eeprom handling via nvmem aliases
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYN105QAKCRDKSWXLKUoM
IZiFAJ9CIiEpHiBbnAhA0VOMGoaXHGULywCdED/5dNgVtc1C7y4avzETbEyWzD4=
=CdMa
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2021.10' of https://source.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2021.10
clk:
- Add driver for Xilinx Clocking Wizard IP
fdt:
- Also record architecture in /fit-images
net:
- Fix plat/priv data handling in axi emac
- Add support for 10G/25G speeds
pca953x:
- Add missing dependency on i2c
serial:
- Fix dependencies for DEBUG uart for pl010/pl011
- Add setconfig option for cadence serial driver
watchdog:
- Add cadence wdt expire now function
zynq:
- Update DT bindings to reflect the latest state and descriptions
zynqmp:
- Update DT bindings to reflect the latest state and descriptions
- SPL: Add support for ECC DRAM initialization
- Fix R5 core 1 handling logic
- Enable firmware driver for mini configurations
- Enable secure boot, regulators, wdt
- Add support xck devices and 67dr
- Add psu init for sm/smk-k26 SOMs
- Add handling for MMC seq number via mmc_get_env_dev()
- Handle reserved memory locations
- Add support for u-boot.itb generation for secure OS
- Handle BL32 handoffs for secure OS
- Add support for 64bit addresses for u-boot.its generation
- Change eeprom handling via nvmem aliases
Add zynqmp 67dr silicon to zynqmp device id table.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Init GICv3 for V3U Falcon in early phase
Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Init the Generic Timer for V3U Falcon in early phase
Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Add board code for the R8A779A0 V3U Falcon board.
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
--
Marek: - various small rebase fixes and clean ups
TF-A and SecureOS can allocate the part of DDR for self but U-Boot is not
handling this configuration that the part of memory is reserved and
shouldn't be used by U-Boot. That's why read all reserved memory locations
and don't use it.
The code was taken from commit 4a1b975dac ("board: stm32mp1: reserve
memory for OP-TEE in device tree") and commit 1419e5b516 ("stm32mp:
update MMU config before the relocation") which is used by stm32 and does
the job properly.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
K26 has EMMC and SD and default 0 is not working when system is booting out
of SD which is controller 1. Add controller autodetection via
mmc_get_env_dev(). The same code is used for distro_boot selection done in
board_late_init(). bootseq variable can't be reused because this is called
so late.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
SVDs are using different name which can't be handled via zynqmp_devices
structure. That's why introduce zynqmp_detect_svd_name() which checks ID
code for these devices and show proper name for them.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Use the correct name for STMicroelectronics phys config properties,
replace '_' by '-':
"st,eth_clk_sel" => "st,eth-clk-sel"
"st,eth-ref-clk-sel" => st,eth-clk-sel"
These property name are aligned with the upstreamed Linux kernel binding:
linux/Documentation/devicetree/bindings/net/stm32-dwmac.yaml
See Linux kernel commit "dt-bindings: net: stmmac: add phys config
properties" merged in v5.1-rc1.
This patch allow to reuse the kernel device tree directly in U-Boot.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmDLD78cHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyLhSB/0UqOd+Ujf2meiHU9yr
oOOCLxVTjTUfIZKLad/zwlj2Xqzsjs6XMawC95BgouvkQLmj/gwerRWcZPg9l7/X
hvb9VJi+iJoLRRpBPbeF3bMb92kCE+YZodFXyutlcY+Z0ZB9755zoVgR6ccKfksd
Xp2y8AFptfYQNZ1l0yb3lhm1261CldWALrGTjRpY2hQ8nEMbV8z6WUB1hAF9CECa
PGbKaiqm9OdktwHsLy4cYFFCuzkykn6T3P6ODineP7IxgEgZKTfJClSTFGY9S0GQ
kwd7K/7j0W3rI5NPknB+Fb4IFAaTs/oozR+5ml7j+2S3G5GXjSGx8zaSOmOZvpP3
KxwN
=/I5V
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2021.10-a' of https://source.denx.de/u-boot/custodians/u-boot-atmel into next
First set of u-boot-atmel features for the 2021.10 cycle:
This feature set converts the boards pm9261 and pm9263 Ethernet support
to DM; enables hash command for all SAM boards; fixes the NAND pmecc
bit-flips correction; adds Falcon boot for sama5d3_xplained board; and
other minor adjustments.
Add Priyanka Jain as MAINTAINER for
T2080RDB_revD_defconfig,
T2080RDB_revD_NAND_defconfig,
T2080RDB_revD_SDCARD_defconfig and
T2080RDB_revD_SPIFLASH_defconfig
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Under DM, we rely on u-boot's device tree to provide the correct PHY
addresses. The board_fix_fdt callback is intended to be used for
device tree fixups before relocation. Unfortunately, this isn't an
option when booting from flash since the device tree isn't writable
before relocation.
This patch introduces the CONFIG_T2080RDB_REV_D option to signal that a
board revision D or up is the target. The config option is used to set
the correct Aquantia PHY address in the board's u-boot device tree.
Defconfig files with the option enable explicitly are added for
convenience.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The T2080RDB boards revisions D and up have updated 10G Aquantia PHYs
connected to MAC1 and MAC2. The second Aquantia PHY is located at a
different address on the MDIO bus compared to rev C (0x8 instead of 0x1).
Fix-up the Linux device tree to update the PHY address for the second
Aquantia PHY on boards revisions D and up. Also rename the PHY node to
reflect the changes.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Detect and print the board revision version based on the CPLD registers.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Both DM_ETH and DM_PCI are enabled for the T2080RDB board. Remove the
board_eth_init() callback and the non-DM_ETH code paths since they are not
needed anymore.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This patch adds the front led initialization and the application
buffer enable to the eraly board inititlaization.
Signed-off-by: Rainer Boschung <rainer.boschung@hitachi-powergrids.com>
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This is most probably a typo, and in older u-uboot versions is same as
'saveenv', in the newer uboot versions there is a separate 'save' command
that is different from 'saveenv'.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
From production view this is standard test executed during production on
all linux based foxmc cards.
On CENT2 HW defined memory region is zero means that some DDR accesses are
done by memory_post_dataline and memory_post_addrline but pattern tests
are skipped that's why mem_regions is fast there.
On ls102x for the complete DDR region of 1GiB memory_regions_post_test
takes approx. 4min and this is too much for production, so this patch
defines only 1MiB region as compromise.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The EXPU1 design is a new 40G capable ethernet service unit card for
Hitachi-Powergrids wired-com product lines.
The base SoC is same as for already added SELI8 card, consequently the
already added u-boot support for SELI8 is reused.
Signed-off-by: Rainer Boschung <rainer.boschung@hitachi-powergrids.com>
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
[Fixed new line error at EOF]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Commit df86d32 breaks linux kernel and product application boot.
Linux kernel and our product application scripts are expecting 0x prefix
for hexadecimal values, while env_set_hex writes them without a prefix.
This patch partially revert env_set_hex usage for affected env variables.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add check for return value of adjust_vdd()
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Priyanka Singh <priyanka.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Now that the k210 clock driver does not depend on CCF, we should no longer
imply it (and probably should not have in the first place). We can also
reduce the pre-relocation malloc arena back to something sensible.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
When using bootefi to boot a EFI binary, u-boot is supposed to
provide networking service for EFI application. Currently, 'pfe stop'
command is called from bootcmd before running bootefi. As a result
network stops working for EFI applications and console is flooded with
"Rx pkt not on expected port" messages.
Implement board_quiesce_devices() for ls1012a boards and call
pfe_command_stop() from it instead of calling 'pfe stop' from
*_bootcmd and bootcmd.
Tested-by: Anji Jagarlmudi <anji.jagarlmudi@nxp.com>
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
[Fixed checkpatch space error]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
One of the points of putting the rescue boot command into default
environment is that user can invoke it without physical access to the
board (without having to press the factory reset button), by running
run bootcmd_rescue
in U-Boot's console.
Therefore we have to ensure that bootcmd_rescue is always set to default
value, regardless of whether the factory reset button was pressed.
Otherwise the variable will be empty for example after upgrade from
previous U-Boot.
Fixes: ec3784d626 ("arm: mvebu: turris_mox: add support for board rescue mode")
Fixes: 176c3e7760 ("arm: mvebu: turris_omnia: support invoking rescue boot from console")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
This supports Falcon boot support for Microchip SAMA5D3 Xplained,
tested on raw MMC, and on raw NAND.
spl_start_uboot() is has the simplest possible implementation.
It doesn't test the environment because enabling environment support
currently causes the SPL to exceed its maximum size (64 KiB).
It doesn't check the serial for incoming characters either because
this functionality currently doesn't seem to work from the SPL
on this board.
Settings for Falcon boot from at FAT partition are also added to
avoid compile failures when CONFIG_SPL_OS_BOOT is enabled, but this
particular case is currently not functional as adding FAT and
partition support cause the SPL to be too big again.
Signed-off-by: Michael Opdenacker <michael.opdenacker@bootlin.com>
Update build instructions and image formats based on HSM rearch. A new
DM image is added into the build, which gets executed right after R5
SPL finishes its job.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
board_fit_image_post_process() passes only start and size of the image,
but type of the image is not passed. So pass fit and node_offset, to
derive information about image to be processed.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
The default register configuration after powerup for PSSYSMON_ANALOG_BUS
register is incorrect. Hence, fix this in SPL by writing correct fixed
value. It follows UG1085 chapter 'PS SYSMON Analog_Bus' and reflects commit
sw_apps:zynq ("056ca65d44549ce27f716d423e8dfdefeee7440c")
in Xilinx:embeddedsw[1].
[1] https://github.com/Xilinx/embeddedsw
Signed-off-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Configure blinking on ethernet PHY LEDs on the MOX A board when entering
rescue mode via reset button.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Add necessary config options and board code to support board factory
reset / rescue mode on Turris MOX.
In order to also support invoking rescue mode from U-Boot console,
without having to press the factory reset button, put the rescue command
into `bootcmd_rescue` default environment variable. When factory reset
button is pressed, invoke rescue mode via distroboot by setting
`boot_targets` to `rescue`.
Rescue boot from console can be invoked by running
run bootcmd_rescue
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Add support for Storopack's SMEGW01 board, which is an
IoT gateway based on the i.MX7D SoC.
Based on the original U-Boot work done by Phytec.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Enable driver model support for FEC ethernet which allows us to remove
the iomux and board_eth_init function. Replace the toggling of the ethernet
phy reset with dt configuration.
Enable driver model support for PCI which allows us to remove the
eth1000_initialize() call. Additionally enable PCI_INIT_R to scan for
PCI devices on init such as the e1000 that is present on the GW552x.
Convert board_pci_fixup to use dm callback and remove pcidisable env
variable which is not supported for DM_PCI and thus leave PCI always
enabled during init.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
A simple prototyping board with one microSD port, one Ethernet port,
2 USB ports, I2C, SPI, GPIO, and UART interfaces.
Signed-off-by: Oleh Kravchenko <oleg@kaa.org.ua>
Cc: Stefano Babic <sbabic@denx.de>
Board designed for quick prototyping and has one microSD port,
2 Ethernet ports, 2 USB ports, I2C, SPI, CAN, RS-485, GPIO,
UART interfaces, and 2 RGB LEDs.
Signed-off-by: Oleh Kravchenko <oleg@kaa.org.ua>
Cc: Stefano Babic <sbabic@denx.de>
The board was not converted to DM_VIDEO before deadline, so disable
video support for now.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Make it possible to invoke rescue boot from U-Boot console, without
having to press the factory reset button. This is needed when accessing
the device remotely, for example.
Achieve this by putting rescue command into `bootcmd_rescue` default
environment variable and setting some distroboot environment variables
to their default values when the factory button is pressed.
Rescue boot from console can be invoked by running
run bootcmd_rescue
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Update rescue mode boot command on Turris Omnia. We are compressing the
image with lzma now.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Add defconfig and board support for HiFive Unmatched.
Signed-off-by: Green Wan <green.wan@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Currently the code sets eth1addr only if /ethernet1 alias exists in DT,
the node pointed to by the alias has "micrel,ks8851-mll" compatible
string, and the KSZ8851 CCR register read indicates programmed EEPROM
is not connected.
This is not sufficient to detect cases where the DT still contains the
KSZ8851 nodes, but the chip itself is not present. Extend the detection
to handle these cases.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Adding new DH electronics mailing list.
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Remove qemu_mips boards because DM migration doesn't make sense.
The board support for qemu_mips is already marked as deprecated
in Qemu in favour of the Malta board. Also qemu_mips support
has been removed from Linux a long time ago.
The official replacement is the Malta board. The same Malta U-Boot
image can be used with Qemu and on physical hardware.
All combinations of Big Endian and Little Endian as well as 32 bit
and 64 bit are supported.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
When building with LTO, the compiler complains about type mismatch of
function usb_gadget_handle_interrupts(). This function is defined
without parameters in files
arch/arm/mach-rockchip/board.c
board/samsung/common/exynos5-dt.c
but it should have one parameter, int index.
Fix this.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This commit does the same thing as Linux commit 33def8498fdd.
Use a more generic form for __section that requires quotes to avoid
complications with clang and gcc differences.
Remove the quote operator # from compiler_attributes.h __section macro.
Convert all unquoted __section(foo) uses to quoted __section("foo").
Also convert __attribute__((section("foo"))) uses to __section("foo")
even if the __attribute__ has multiple list entry forms.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use the new BINMAN_STANDALONE_FDT option for AE350 based SPL defconfigs,
so that binman is now used to generate u-boot.itb.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Rick Chen <rick@andestech.com>
At present SiFive Unleashed board uses the Makefile to create the FIT,
using USE_SPL_FIT_GENERATOR, which is deprecated as per the Makefile
warning. Update to use binman instead.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The current capsule authentication code checks if the environment
variable capsule_authentication_enabled is set, for authenticating the
capsule. This is in addition to the check for the config symbol
CONFIG_EFI_CAPSULE_AUTHENTICATE. Remove the check for the environment
variable. The capsule will now be authenticated if the config symbol
is set.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviwed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This patch adds the base support for the Marvell Octeon TX2 CN913x DB.
Only one defconfig is added with this patch. Other board variants are
available (NAND, MMC booting) and images for these boards can be
generated by following the documentation added in the included README.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This is more consistent with the naming of other ram banks, and matches
what Linux is doing.
Reported-by: Damien Le Moal <Damien.LeMoal@wdc.com>
Signed-off-by: Sean Anderson <seanga2@gmail.com>
We just need to initialize all the clocks pre-reloc. The clock driver
creates a bunch of devices, so we need to increase the pre-reloc malloc
arena.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Update the Kconfig and the board file to make the am335x board compatible
with cape detection.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
The am335x from BeagleBone use i2c EEPROM to detect capes.
The memory is wired to i2c bus 2 therefore it need to be enabled.
Add i2c2 clock, pinmux description and pinmux enable function.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Add the extension_board_scan specific function to scan the information
of the EEPROM on one-wire and fill the extension struct.
Add the Kconfig symbol to enable the needs to detect DIPs.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Andre Przywara <andre.przywara@arm.com>
The BeagleBone platforms all use a common mechanism to discover and
identify extension boards (called "capes"): each extension board has an
I2C-connected EEPROM describing itself.
This patch implements a generic extension_scan_board() feature that can
be used by all BeagleBone platforms to read those I2C EEPROMs and fill
in the list of "extension" structures.
Following commits will enable this common logic on two BeagleBone
platforms.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
This commit extends the sandbox to implement a dummy
extension_board_scan() function and enables the extension command in
the sandbox configuration. It then adds a test that checks the proper
functionality of the extension command by applying two Device Tree
overlays to the sandbox Device Tree.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
[trini: Limit to running on sandbox]
Signed-off-by: Tom Rini <trini@konsulko.com>
Enable CONFIG_DM_ETH in configs/pm9263_defconfig
Drop legacy initialization in board/ronetix/pm9263.c
Remove network related setting from include/configs/pm9263.h
Signed-off-by: Ilko Iliev <iliev@ronetix.at>
Scrub duplicate /memory@* node entries here. Some R-Car DTs might
contain multiple /memory@* nodes, however fdt_fixup_memory_banks()
either generates single /memory node or updates the first /memory
node. Any remaining memory nodes are thus potential duplicates.
However, it is not possible to delete all the memory nodes right
away, since some of those might not be DRAM memory nodes, but some
sort of other memory. Thus, delete only the memory nodes which are
in the R-Car3 DBSC ranges.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
The rcar-common/common.c contains various common board functions shared
by all R-Car and RZG boards. This board is not compiling the file in, so
add it. This way, part of the board code can be de-duplicated too.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Adam Ford <aford173@gmail.com>
Parse MAC addresses from EEPROM and set them in the env. This is needed
to get MAC address for additional ethernet ports on the EVM.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
I2C EEPROM data contains the board name and its revision.
Add support for:
- Reading EEPROM data and store a copy at end of SRAM
- Updating env variable with relevant board info
- Printing board info during boot.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
In SPL, DDR should be made available by the end of board_init_f()
so that apis in board_init_r() can use ddr. Adding support for
triggering DDR initialization from board_init_f().
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Create a new CONFIG_K3_DDRSS option to select the common parts of the
k3-ddrss driver. Also introduce a choice that depends on the top level
option to select CONFIG_K3_J721E_DDRSS for j721e support, and update
corresponding Kconfig as required.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
These specific configs are missing a number of migrations. In addition,
they are blocking completion of the now-expired DM_MMC migration as it
requires enabling BLK.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Ruchika Gupta <ruchika.gupta@nxp.com>
Cc: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Supported peripherals: Ethernet, eMMC, Serial.
U-Boot SPL 2021.04-00911-g5fa1e2ffeb-dirty (Apr 23 2021 - 09:11:14
+0200)
Normal Boot
Trying to boot from MMC2
U-Boot 2021.04-00911-g5fa1e2ffeb-dirty (Apr 23 2021 - 09:11:14 +0200)
CPU: Freescale i.MX8MQ rev2.1 at 1000 MHz
Reset cause: POR
Model: Ronetix iMX8M-CM SoM
DRAM: 1 GiB
WDT: Started with servicing (60s timeout)
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... OK
In: serial
Out: serial
Err: serial
Net:
Warning: ethernet@30be0000 (eth0) using random MAC address -
42:0d:e7:78:da:53
eth0: ethernet@30be0000
Hit any key to stop autoboot: 0
u-boot=>
Signed-off-by: Ilko Iliev <iliev@ronetix.at>
Current setup instructions for i.MX8QM MEK board include somewhat
conflicting instructions, so here's an attempt to fix it.
After trying both sets of firmwares, I can conclude that both of
them fail to work:
- no boot at all with imx-sc-firmware-0.7 / firmware-imx-7.6
- partial success with imx-sc-firmware-1.1 / firmware-imx-8.0:
U-Boot 2021.04-rc3-00135-ge0669a43c8 (Mar 08 2021 - 16:49:08 +0200)
CPU: NXP i.MX8QM RevB A53 at 1200 MHz
Model: Freescale i.MX8QM MEK
Board: iMX8QM MEK
mu_hal_receivemsg timeout
Build: SCFW 65afe5f6, SECO-FW 65afe5f6, ATF a-20190
mu_hal_receivemsg timeout
sc_misc_get_boot_dev: res:16
Boot: SD0
DRAM: mu_hal_sendmsg timeout
sc_rm_is_memreg_owned: mr:0 res:21
...
Signed-off-by: Priit Laes <priit.laes@paf.com>
Engicam C.TOUCH 2.0 is an EDIMM compliant general purpose Carrier
board.
Genaral features:
- Ethernet 10/100
- Wifi/BT
- USB Type A/OTG
- Audio Out
- CAN
- LVDS panel connector
i.Core MX8M Mini is an EDIMM SoM based on NXP i.MX8M Mini from Engicam.
i.Core MX8M Mini needs to mount on top of this Carrier board for
creating complete i.Core MX8M Mini C.TOUCH 2.0 board.
Linux dts commit details:
commit <a142252061ff> ("arm64: dts: imx8mm: Add Engicam i.Core MX8M Mini
C.TOUCH 2.0")
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Engicam EDIMM2.2 Starter Kit is an EDIMM 2.2 Form Factor Capacitive
Evaluation Board.
Genaral features:
- LCD 7" C.Touch
- microSD slot
- Ethernet 1Gb
- Wifi/BT
- 2x LVDS Full HD interfaces
- 3x USB 2.0
- 1x USB 3.0
- HDMI Out
- Mini PCIe
- MIPI CSI
- 2x CAN
- Audio Out
i.Core MX8M Mini is an EDIMM SoM based on NXP i.MX8M Mini from Engicam.
i.Core MX8M Mini needs to mount on top of this Evaluation board for
creating complete i.Core MX8M Mini EDIMM2.2 Starter Kit.
Linux dts commit details:
commit <051c08eea682> ("arm64: dts: imx8mm: Add Engicam i.Core MX8M Mini
EDIMM2.2 Starter Kit")
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
The DA9063 enables the CRYSTAL bit by default, but there is no
crystal populated on the BA16 system on module. Without explicitly
clearing the CRYSTAL bit the system runs unstable and sometimes
reboots unexpectedly.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Currently, all comphy definitions are PHY_TYPE_XX and PHY_SPEEED_XX.
Those definition might be confused with MDIO PHY definitions.
This patch does the following changes:
- PHY_TYPE_XX --> COMPHY_TYPE_XX
- PHY_SPEED_XX --> COMPHY_SPEED_XX
This improves readability, no functional change.
Change-Id: I2bd1d9289ebbc5c16fa80f9870f797ea1bcaf5fa
Signed-off-by: Igal Liberman <igall@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
This patch adds the base support for the Marvell Octeon TX2 CN9130 CRB.
Not all interfaces are supported fully yet.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds the board specific QLM/DLM init code to the Octeon 3
EBB7304 board. The configuration of each port is read from the
environment exactly as done in the 2013 U-Boot version to keep the
board and it's configuration compatible.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
- MIPS: octeon: add support for QLM and PCI-E controller
- MIPS: octeon: add support for AHCI and SATA
- MIPS: octeon: add E1000 ethernet support
- MIPS: octeon: add Octeon III NIC23 board
- ata/scsi: add support for Big Endian platforms
-----BEGIN PGP SIGNATURE-----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=JwRN
-----END PGP SIGNATURE-----
Merge tag 'mips-pull-2021-04-24' of https://source.denx.de/u-boot/custodians/u-boot-mips
- MIPS: octeon: fix minor bugs of initial merge
- MIPS: octeon: add support for QLM and PCI-E controller
- MIPS: octeon: add support for AHCI and SATA
- MIPS: octeon: add E1000 ethernet support
- MIPS: octeon: add Octeon III NIC23 board
- ata/scsi: add support for Big Endian platforms
This patch adds the board specific QLM/DLM init code to the Octeon 3
EBB7304 board. The configuration of each port is read from the
environment exactly as done in the 2013 U-Boot version to keep the
board and it's configuration compatible.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Currently u-boot supports addresses upto 39-bits only. If anybody
wants to use addresses of more than 39-bits in Linux they will have
a separate memory node in DT. In such cases they will have multiple
memory nodes.
Currently u-boot selects and runs on lower memory bank region.
But bootscript is being loaded on dram bank 0, where dram bank 0 will
point to 1st memory node in DT. If first memory node is mentioned as
higher ddr(>39-bits address) then u-boot cannot load the bootscript.
So fix this issue by setting bootscript address within the lower memory
bank region.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Change "dfu_usb" to "usb_dfu" for better representation and change
required macros. Add 60s timeout of dfu-utils to start transaction.
Add support for usb thor to distro boot. Remove DFU_ALT_INFO_RAM
as we use bootcmd_usb_dfu instead of dfu_ram.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
In usb boot mode distro boot should select usb device as primary boot
device instead of usb host. So make usb dfu as primary boot device. But do
not list it in boot_targets as fallback option because it is not classic
mode for booting. Using 60s timeout by default should be enough time for
dfu-utils to start transaction. In case none needs this please change
timeout value in the command or disable CONFIG_DFU_TIMEOUT.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enable saving variables to MMC(FAT) and SPI based on primary
bootmode. If bootmode is JTAG, dont save env anywhere(NOWHERE).
Enable ENV_FAT_DEVICE_AND_PART="0:auto" for Versal platforms as well.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enable saving variables to MMC(FAT), NAND, SPI based on primary
bootmode. If bootmode is JTAG, dont save env anywhere(NOWHERE).
Since most of the flashes on zynq evaluation boards are 16MB in size,
set default ENV_OFFSET to 15MB(0xE00000).
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
U-boot might display wrong module revision information
for modules with an assembly version 'K'. "cfgblock create"
does not takes into account all revision digits from PID8.
This fix takes into account all digits of PID8
to store module revision.
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Rob does not have access to any Calxeda systems anymore, also has
expressed a lack of interest in those systems in the past.
I have multiple working Midway nodes under my desk in the office, so
am happy to take over maintainership.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
