I was trying to employ lpddr4_mr_read() to something similar to what
the imx8mm-cl-iot-gate board is doing for auto-detecting the RAM
type. However, the version in drivers/ddr/imx/imx8m/ddrphy_utils.c
differs from the private one used by that board in how it extracts the
byte value, and I was only getting zeroes. Adding a bit of debug
printf'ing gives me
tmp = 0x00ffff00
tmp = 0x00070700
tmp = 0x00000000
tmp = 0x00101000
and indeed I was expecting a (combined) value of 0xff070010 (0xff
being Manufacturer ID for Micron). I can't find any documentation that
says how the values are supposed to be read, but clearly the iot-gate
definition is the right one, both for its use case as well as my
imx8mp-based board.
So lift the private definition of lpddr4_mr_read() from the
imx8mm-cl-iot-gate board code to ddrphy_utils.c, and add a declaration
in the ddr.h header where e.g. get_trained_CDD() is already declared.
This has only been compile-tested for the imx8mm-cl-iot-gate
board (since I don't have the hardware), but since I've merely moved
its definition of lpddr4_mr_read(), I'd be surprised if it changed
anything for that board.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Tested-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Introduce helper macro UART_BASE_ADDR(n), which returns Nth UART base
address. Convert all board configurations to this new macro. This is the
first step toward switching CONFIG_MXC_UART_BASE to Kconfig. This is a
clean up, no functional change.
The new macro contains compile-time test to verify N is in suitable
range. The test works such that it multiplies constant N by constant
double-negation of size of a non-empty structure, i.e. it multiplies
constant N by constant 1 in each successful compilation case.
The non-empty structure may contain C11 _Static_assert(), make use of
this and place the kernel variant of static assert in there, so that
it performs the compile-time check for N in the correct range. Note
that it is not possible to directly use static_assert in compound
statements, hence this convoluted construct.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Introduce helper macro UART_BASE_ADDR(n), which returns Nth UART base
address. Convert all board configurations to this new macro. This is the
first step toward switching CONFIG_MXC_UART_BASE to Kconfig. This is a
clean up, no functional change.
The new macro contains compile-time test to verify N is in suitable
range. The test works such that it multiplies constant N by constant
double-negation of size of a non-empty structure, i.e. it multiplies
constant N by constant 1 in each successful compilation case.
The non-empty structure may contain C11 _Static_assert(), make use of
this and place the kernel variant of static assert in there, so that
it performs the compile-time check for N in the correct range. Note
that it is not possible to directly use static_assert in compound
statements, hence this convoluted construct.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Introduce helper macro UART_BASE_ADDR(n), which returns Nth UART base
address. Convert all board configurations to this new macro. This is the
first step toward switching CONFIG_MXC_UART_BASE to Kconfig. This is a
clean up, no functional change.
The new macro contains compile-time test to verify N is in suitable
range. The test works such that it multiplies constant N by constant
double-negation of size of a non-empty structure, i.e. it multiplies
constant N by constant 1 in each successful compilation case.
The non-empty structure may contain C11 _Static_assert(), make use of
this and place the kernel variant of static assert in there, so that
it performs the compile-time check for N in the correct range. Note
that it is not possible to directly use static_assert in compound
statements, hence this convoluted construct.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
The I2C2 has SMBus device SMSC USB2514Bi connected to it, the device is
capable of up to 100 kHz operation. Reduce the bus frequency to 100 kHz
to guarantee this I2C device can work correctly.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
When trying to boot via USB on i.MX8MN it is necessary to specify
the U-Boot environment location, otherwise the boot process simply
hangs.
Specify the environment location when booting from USB.
Tested on a imx8mn-evk.
Suggested-by: Michael Nazzareno Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Tested-By: Tim Harvey <tharvey@gateworks.com>
The Avenger96 board comes in multiple regulator configurations.
- rev.100 or rev.200 have Buck3 preconfigured to 3V3 operation on
boot and contains extra Enpirion EP53A8LQI DCDC converter which
supplies the IO. Reduce Buck3 voltage to 2V9 to not waste power.
- rev.200L have Buck3 preconfigured to 1V8 operation and have no
Enpirion EP53A8LQI DCDC anymore, the IO is supplied from Buck3.
Configure the Buck3 voltage on this board per PMIC NVM settings and
update buck3 voltage limits in DT passed to OS before booting OS to
prevent potential hardware damage.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
BTN_MISC looks like the most reasonable option for this button.
Button is used by firmware to indicate (after reset, power up) that user
wants to do firmware upgrade via firmware update utility.
For bootloader or OS is this just user button which is worth to have it
mapped.
Also button can be used as a wakeup source and pressing it for more time
can generate more chars that's why also adding wakeup-source and autorepeat
properties.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Link: https://lore.kernel.org/r/7f6d627473632c3c3036ec9f6aaa36e00f4615e2.1652262769.git.michal.simek@amd.com
SGMII requires phy to be configured. The support for this has been added to
Linux and U-Boot already that's why also describe the phy via DT. Clock is
coming from si5332 chip (output 1) 125MHz which is only one GT line use on
this board.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/8ad8d0c2fc9690cc90f95feddf87b0e94a685a43.1652262769.git.michal.simek@amd.com
OPP table name now should start with "opp-table" and OPP entries
shouldn't contain commas and @ signs in accordance to the new schema
requirement.
The same change was done in Linux by commit c6d4a8977598 ("ARM: tegra:
Rename CPU and EMC OPP table device-tree nodes"), commit ffbe853a3f5a
("ARM: dts: sunxi: Fix OPPs node name") or commit b7072cc5704d ("arm64:
dts: qcom: qcs404: Rename CPU and CPR OPP tables").
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/a1176349448df35127dbac15c1eeb2229505bae7.1652262769.git.michal.simek@amd.com
In all the ZynqMP boards dts files tx-buswidth is by default set to 1. Due
to this the framework only issues 1-1-1 write commands to the GQSPI driver.
But the GQSPI controller is capable of handling 1-4-4 write commands, so
updated the tx-buswidth to 4 in ZynqMP boards dts files. This would enable
the spi-nor framework to issue 1-4-4 write commands instead of 1-1-1. This
will increase the tx data transfer rate, as now the tx data will be
transferred on four lines instead on single line.
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/ad61199f55e5e00f29de6206d9d1872a52a7657e.1652193179.git.michal.simek@amd.com
This patch fixes two issues in the set_r5_reset function.
1. When in split mode, the lpd_amba_rst bit should only be set when
both r5 cpu cores are in reset. Otherwise, if one r5 core is still
running, setting the lpd_amba_rst bit will cause an error for the
running core. The set_r5_reset function has been modified to check
if the other r5 core is still running before setting the lpd_amba_rst
bit.
2. The cpu_disable function was always assuming that the r5 cores
are in split mode when resetting either core 4 or 5. This is
incorrect for lockstep functionality. This patch adds a function
check_r5_mode to handle the cpu_disable function correctly for
the r5 cores by checking the mode and handling the reset appropriately.
Signed-off-by: Neal Frager <neal.frager@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/d99cbd7f2394ac055ef27457298f554ff0747ba7.1651648344.git.michal.simek@amd.com
Moving of internal registers from INTREG_BASE_ADDR_REG to SOC_REGS_PHY_BASE
needs to be done very early, prior calling any function which may touch
internal registers, like debug_uart_init().
So do it earlier in arch_very_early_init() instead of arch_cpu_init().
Movement is done in proper U-Boot, not in SPL. SPL may return to bootrom
and bootrom requires internal registers at (old) expected location.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
When this option is set then ARM _main() function would call
arch_very_early_init() function at the beginning. It would be before
calling any other functions like debug_uart_init() and also before
initializing C runtime environment.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Nothing selects ARMADA_64BIT. Instead the 64-bit SoCs just select ARM64
directly. Remove the unused config item.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
STM32 programmer improvements
video: support several LTDC HW versions and fix data enable polarity
board: fix stboard error message, consider USB cable connected when boot device is USB
configs: stm32mp1: set console variable for extlinux.conf
configs: stm32mp1: add support for baudrate higher than 115200 for ST-Link
ARM: stm32mp: Fix Silicon version handling and ft_system_setup()
phy: stm32-usbphyc: Add DT phy tuning support
arm: dts: stm32mp15: alignment with v5.18
ram: Conditionally enable ASR
mach-stm32mp: psci: retain MCUDIVR, PLL3CR, PLL4CR, MSSCKSELR across suspend
configs: Use TFTP_TSIZE on DHSOM and STMicroelectronics boards
ARM: stm32: Use default CONFIG_TFTP_BLOCKSIZE on DHSOM
pinctrl: stm32: rework GPIO holes management
-----BEGIN PGP SIGNATURE-----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=s7xn
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20220510' of https://source.denx.de/u-boot/custodians/u-boot-stm
Add new STM32 MCU boards and Documentation
STM32 programmer improvements
video: support several LTDC HW versions and fix data enable polarity
board: fix stboard error message, consider USB cable connected when boot device is USB
configs: stm32mp1: set console variable for extlinux.conf
configs: stm32mp1: add support for baudrate higher than 115200 for ST-Link
ARM: stm32mp: Fix Silicon version handling and ft_system_setup()
phy: stm32-usbphyc: Add DT phy tuning support
arm: dts: stm32mp15: alignment with v5.18
ram: Conditionally enable ASR
mach-stm32mp: psci: retain MCUDIVR, PLL3CR, PLL4CR, MSSCKSELR across suspend
configs: Use TFTP_TSIZE on DHSOM and STMicroelectronics boards
ARM: stm32: Use default CONFIG_TFTP_BLOCKSIZE on DHSOM
pinctrl: stm32: rework GPIO holes management
The Buck3 on DHCOR is used to supply IO voltage. It can output either 3V3
in the default DHCOR configuration, or 2V9 in case of AV96 DHCOR variant
which has extra Empirion DCDC converter in front of the 1V8 IO supply, or
outright 1V8 in case of 1V8 IO DHCOR without the Empirion DCDC converter.
The 2V9 mode in case of AV96 DHCOR variant is used to reduce unnecessarily
high input voltage to the Empirion DCDC converter, so move it into matching
DTSI to stop confusing users.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
The SoC seems to lose the values of MCUDIVR, PLL3CR, PLL4CR, RCC_MSSCKSELR
during suspend/resume cycle, cache them and reinstate their values on resume.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Device tree alignment with Linux kernel v5.18-rc2:
- ARM: dts: stm32: Add support for the emtrion emSBC-Argon
(only the pincontrol part)
- ARM: dts: stm32: Drop duplicate status okay from DHCOM gpioc node
- ARM: dts: stm32: add st,stm32-sdmmc2 compatible on stm32mp151
- ARM: dts: stm32: fix AV96 board SAI2 pin muxing on stm32mp15
- ARM: dts: stm32: use exti 19 as main interrupt to support RTC wakeup on
stm32mp157
- ARM: dts: stm32: add DMA configuration to UART nodes on stm32mp151
- ARM: dts: stm32: keep uart4 behavior on *
- ARM: dts: stm32: Correct masks for GIC PPI interrupts on stm32mp15
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Handle correctly the silicon revision = REV_ID[15:0] of Device Version
and the associated device marking, A to Z on STMicroelectronics STM32MP
SOCs.
This patch prepare the introduction of next STM32MP family,
with STM32MP13x Rev.Z for REV_ID = 1.1.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
The function ft_system_setup shouldn't return an error when the
/soc node is absent in the provided device tree but just skip the
updates.
This patch solves an issue when the U-Boot pytest is executed on board.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Accept flashlayout without header in alternate 0, to simplify
the support of stm32prog command with dfu-util.
By default the flashlayout file size is the size of the received binary,
provided with the offset in the DFU alternate.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Update the stm32prog command to allow the reception of U-Boot script in
the FlashLayout alternate during the first USB enumeration.
This patch is aligned with the last TF-A behavior: the Flashlayout
is now loaded by U-Boot; it is no more present at STM32_DDR_BASE when
the stm32prog is launched after a serial boot, on UART or on USB.
The received script must be a U-Boot legacy image, no more need to add
a stm32image header.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
When an interruption is received during the first USB enumeration
used to received the FlashLayout, with handle ctrl-c, the second
enumeration is not needed and the result for stm32prog_usb_loop
is false (reset is not needed).
This patch avoids the need of a second ctrl to interrupt the command
stm32prog.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add support of UUID for FIP parttion, required by Firmware update
support in TF-A:
- UUID TYPE for FIP partition: 19d5df83-11b0-457b-be2c-7559c13142a5
- "fip-a" partition UUID: 4fd84c93-54ef-463f-a7ef-ae25ff887087
- "fip-b" partition UUID: 09c54952-d5bf-45af-acee-335303766fb3
This check is done with a new partition type "FIP" associated
at the FIP UUID.
The A/B partition UUID is detected by the partition name:
"fip-a", "fip-b".
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add support of new header for the STM32IMAGE version V2
in command stm32prog command for STM32MP13x family.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
When OP-TEE is used, the SMC for BSEC management are not
available and the PTA provisioning for OTP must be used.
U-Boot opens the session to this PTA and use it for OTP
access.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add a configuration flag CONFIG_CMD_STM32PROG_OTP to enable the support of
OTP update in stm32prog command.
This new configuration allows to deactivate this feature for security reason
and it is a preliminary step for support of OPT update with the OP-TEE
provisioning TA.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
The E4 revision of the AM64 SKEVM embeds a TPS65219 PMIC,
this adds the PMIC node with the required regulators voltages.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
switch the pin definitions from AM33XX_IOPAD to AM33XX_PADCONF macro
Signed-off-by: Gireesh Hiremath <Gireesh.Hiremath@in.bosch.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
With sandbox, U-Boot can be run without a device tree (i.e. no -d or -T
parameter). In this case an empty device tree is created for convenience.
With a recent change this causes an error due to the missing '/binman'
node.
Add this node to avoid the problem, as well as a test that U-Boot can
be run without a device tree.
Fixes: 059df5624b ("arch: Kconfig: imply BINMAN for SANDBOX")
Fixes: https://source.denx.de/u-boot/u-boot/-/issues/11
Signed-off-by: Simon Glass <sjg@chromium.org>
In order to be able to get rid of the non-DM MDIO bus registered in
mvneta driver, start using the DM registered one in Turris MOX board
code.
This also allows us to drop the hack introduced in MOX' -u-boot.dtsi
file.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Add the Octeon ethernet (BGX) and SFP DT nodes to the NIC23 dts file to
enable ethernet support on this board.
Signed-off-by: Stefan Roese <sr@denx.de>
Add the Octeon ethernet (BGX), SMI and PHY DT nodes to the EBB7304 dts
file to enable ethernet support on this board.
Signed-off-by: Stefan Roese <sr@denx.de>
Call octeon_bootmem_init() earlier in the boot process, so that this
bootmemory infrastructure is already initialized when e.g. the
networking support gets probed.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds the newly added C files to the Makefile to enable
compilation. This is done in a separate step, to not introduce build
breakage while adding the single files with potentially missing
externals.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch includes misc changes to already present Octeon MIPS C files
files, which are necessary for the upcoming ethernet support.
The changes are mostly:
- DM GPIO & I2C infrastructure
- Coding style cleanup while reworking of the code
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-range.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-qlm-tables.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-pko-internal-ports-range.c from 2013 U-Boot. It will be used
by the later added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-pko3-resources.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-pko3-compat.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-pko3-queue.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-pko3.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-pko.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-pki-resources.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-pki.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-ipd.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-ilk.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-global-resource.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-fpa-resource.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-fpa.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-fau-compat.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-cmd-queue.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-agl.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-helper-xaui.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-helper-sfp.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-helper-sgmii.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-helper-rgmii.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-helper-pko3.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-helper-pko.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-helper-pki.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-helper-npi.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-helper-loop.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-helper-ipd.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-helper-ilk.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-helper-fpa.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-helper-board.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-helper-bgx.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-helper-agl.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch includes misc changes to already present Octeon MIPS header
files, which are necessary for the upcoming ethernet support.
The changes are mostly:
- DM GPIO & I2C infrastructure
- Coding style cleanup while reworking the headers
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-xcv-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support networking on the MIPS Octeon II /
III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-pcsxxx-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support networking on the MIPS Octeon II /
III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-npei-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support networking on the MIPS Octeon II /
III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-lbk-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support networking on the MIPS Octeon II /
III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-iob-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support networking on the MIPS Octeon II /
III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-igl-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support networking on the MIPS Octeon II /
III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import misc cvmx-helper header files from 2013 U-Boot. They will be used
by the later added drivers to support networking on the MIPS Octeon II /
III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Add a mask parameter to control the lookup of the PCI region from which
the mapping can be made.
Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Evolve dm_pci_map_bar() to include an offset and length parameter. These
allow a portion of the memory to be mapped and range checks to be
applied.
Passing both the offset and length as zero results in the previous
behaviour and this is used to migrate the previous callers.
Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add tests for the functions dm_pci_bus_to_phys() and
dm_pci_phys_to_bus() which convert between PCI bus addresses and
physical addresses based on the ranges declared for the PCI controller.
The ranges of bus#1 are used for the tests, adding a translation to one
of the ranges to cover more cases.
Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
To quote the author:
U-Boot provides a verified-boot feature based around FIT, but there is
no standard way of implementing it for a board. At present the various
required pieces must be built up separately, to produce a working
implementation. In particular, there is no built-in support for selecting
A/B boot or recovery mode.
This series introduces VPL, a verified program loader phase for U-Boot.
Its purpose is to run the verified-boot process and decide which SPL
binary should be run. It is critical that this decision happens before
SPL runs, since SPL sets up SDRAM and we need to be able to update the
SDRAM-init code in the field.
Adding VPL into the boot flow provides a standard place to implement
verified boot. This series includes the phase itself, some useful Kconfig
options and a sandbox_vpl build for sandbox. No verfied-boot support is
provided in this series.
Most of the patches in this series are fixes and improvements to docs and
various Kconfig conditions for SPL.
Add an initial VPL build for sandbox. This includes the flow:
TPL (with of-platdata) -> VPL -> SPL -> U-Boot
To run it:
./tpl/u-boot-tpl -D
The -D is needed to get the default device tree, which includes the serial
console info.
Add a Makefile check for OF_HOSTFILE which is the option that enables
devicetree control on sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
The Zyxel NSA310s board has the network chip Marvell Alaska 88E1318S.
Use uclass mvgbe and the compatible driver M88E1310 driver to bring
up Ethernet.
- Use uclass mvgbe to bring up the network. And remove ad-hoc code.
- Remove CONFIG_RESET_PHY_R.
- Enable CONFIG_PHY_MARVELL to properly configure the network.
- Add phy mode RGMII to kirkwood-nsa310s.dts
- Miscellaneous changes: Move constants to .c file and remove header file
board/zyxel/nsa310s/nsa310s.h, add support for large USB and SATA HDDs,
use BIT macro, add/cleanup comments, and cosmetic changes.
Note that this patch is depended on the following patch:
https://patchwork.ozlabs.org/project/uboot/patch/20220412201820.10291-1-mibodhi@gmail.com/
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Upstream Linux kernel uses for mpc8548-based PCIe controllers compatible
string "fsl,mpc8548-pcie". So change U-Boot fsl PCIe driver and all DTS
files to use "fsl,mpc8548-pcie" instead of "fsl,pcie-mpc8548" to be
compatible with Linux kernel.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Linux P2020 USB kernel driver uses compatible string fsl-usb2-dr-v1.6 and
needs more DT properties. Copy P2020 usb@22000 properties from upstream
Linux kernel.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
interrupts property for spi@7000 node is needed for compatibility with
Linux kernel.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Device tree include file p2020-post.dtsi should be included after the board
device tree file and overrides settings of the board. So it should not
disable some node as board cannot enable it via normal way (it has to
enable it after inclusion of p2020-post.dtsi file).
Fix it by removal of explicit disable in p2020-post.dtsi file and then
remove explicit post-post enable in all P2020 board device tree files.
Currently no P2020 board has spi@7000 node disabled.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Linux kernel eSDHC driver for P2020 requires additional compatible string
fsl,p2020-esdhc and interrupts property. Add them to p2020-post.dtsi file
to make U-Boot board DTS files compatible for Linux kernel.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Import pq3-etsec1-timer-0.dtsi device tree include file from upstream Linux
kernel for P2020. This allows U-Boot to use P2020 device tree files from
upstream Linux kernel which reference ptp_clock@24e00 device.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Import pq3-gpio-0.dtsi device tree include file from upstream Linux kernel
for P2020. This allows U-Boot to use P2020 device tree files from upstream
Linux kernel which reference gpio-controller@fc00 device.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
It is too confusing if sections are defined in non-ascending order.
Also linker has to go backward and then again forward when generating final
binary.
To make future changes easier, define all linker sections in ascending
order.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Linker knows exact size of the image, so there is no need to use
CONFIG_SYS_MONITOR_LEN macro (which should be upper limit).
Remove usage of CONFIG_SYS_MONITOR_LEN macro to simplify setup.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
.interp section is not available in output ELF binary and SIZEOF_HEADERS is
needed at all.
There is no change in generated u-boot.bin binary.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
mpc85xx SPL NAND linker script u-boot-nand_spl.lds is not used since
Jun 2014 commit 0234446fd1 ("nand_spl: remove MPC8536DS support").
Remove it.
Signed-off-by: Pali Rohár <pali@kernel.org>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Currently CONFIG_OF_SEPARATE is completely broken and U-Boot for some
mpc85xx board (e.g. P2020) has to be compiled with CONFIG_OF_EMBED.
Otherwise it crashes during early init.
When debug console is enabled and all debug logging options are turned on
then U-Boot on P2020 with CONFIG_OF_SEPARATE prints following error:
No valid device tree binary found at 110dc300
initcall sequence 110d3560 failed at call 1109535c (err=-1)
### ERROR ### Please RESET the board ###
Problem is with appended DTB. When CONFIG_SYS_MPC85XX_NO_RESETVEC is set
U-Boot binary image without DTB ends immediately after the .u_boot_list
section. At this position is defined _end symbol at which U-Boot expects
start of the appended DTB.
Problem is that after .u_boot_list section are in linker script defined
another sections with 256 byte long padding which are completely empty.
During conversion of U-Boot ELF binary to RAW binary u-boot-nodtb.bin,
objcopy removes trailing zero padding and therefore DTB is appended at
wrong position.
Changing alignment from 256 bytes to 4 bytes fixes this issue. And appended
DTB is finally at he correct position. With this fix U-Boot on P2020 with
CONFIG_OF_SEPARATE option starts working again.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
For compatibility with Linux kernel DTS files and also with other U-Boot
powerpc DTS files, rename esdhc@2e000 node to sdhc@2e000 in p1020-post.dtsi
and p2020-post.dtsi include files.
Linux kernel DTS files which include these dtsi files, expect that esdhc
node has name sdhc@2e000 and do not work with other node names.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This node is required for NAND and NOR support. Node is taken from the
upstream Linux kernel DTS file.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Import pq3-duart-0.dtsi device tree include file from upstream Linux kernel
for P2020. This allows U-Boot to use P2020 device tree files from upstream
Linux kernel which reference serial0 or serial1 devices.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
P2020 DTS files in upstream Linux kernel use fsl/p2020si-pre.dtsi and
fsl/p2020si-post.dtsi include device tree files.
Add symlinks for these include device tree files into U-Boot powerpc
directory and points them to U-Boot inline device tree files p2020.dtsi and
p2020-post.dtsi.
This allows to use P2020 DTS files from upstream Linux kernel in U-Boot.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The real entry point is _start_e500. There is no _start symbol at all. So
rename _start_e500 to _start for convension that _start symbol is used as
entry point.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
_start symbol contains only 32-bit data number 0x27051956 despite it is
marked as text section. This magic number is IH_MAGIC which is used for
marking uboot image header.
mpc85xx start.S code does not define valid uboot image header, so IH_MAGIC
number in _start symbol is useless there.
Moreover this _start symbol is not used at all. Entry point is at symbol
_start_e500.
So because this _start symbol is not used for anything, completely remove
it with IH_MAGIC number. After _start symbol was _start_cont symbol, so
replace all relative address calculations by _start_cont.
Signed-off-by: Pali Rohár <pali@kernel.org>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
NXP/Freescale Layerscape CPUs support high-speed serial interfaces (SERDES)
that can be configured for the application. Interfaces not used by the
application can be set to protocol 0 to turn them off and save power, but
U-Boot would emit a warning that 0 was invalid for a SERDES protocol on
boot. Replace the warning text with a notice that the SERDES is disabled.
Signed-off-by: Stephen Carlson <stcarlso@linux.microsoft.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
There is an user-selectable SYS_HAS_ARMV8_SECURE_BASE, which has the
same meaning but is just for the ls1043ardb board. As no in-tree config
uses this, drop it and replace it with something more sophiticated:
ARMV8_PSCI_RELOCATE. This option will then enable the ARMV8_SECURE_BASE
option which is used as the base to relocate the PSCI code (or any code
in the secure region, but that is only PSCI). A SoC (or board) can now
opt-in into having such a secure region by enabling
SYS_HAS_ARMV8_SECURE_BASE. Enable it for the LS1043A SoC, where it was
possible to relocate the PSCI code before as well as on the LS1028A SoC
where there will be PSCI support soon.
Additionally, make ARMV8_PSCI and SEC_FIRMWARE_ARMV8_PSCI exclusive.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
If we are running in EL2 skip PSCI implementation setup. This avoids an
exception if CONFIG_ARMV8_PSCI is set, but u-boot is started by TF-A.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
There are two different implementations to do a secure monitor call:
smc_call() and arm_smccc_smc(). The former is defined in fwcall.c and
seems to be an ad-hoc implementation. The latter is imported from linux.
smc_call() is also only available if CONFIG_ARMV8_PSCI is not defined.
This makes it impossible to have both PSCI calls and PSCI implementation
in one u-boot build. The layerscape SoC code decide at runtime via
check_psci() if there is a PSCI support. Therefore, this is a
prerequisite patch to add PSCI implementation support for the layerscape
SoCs.
Note, for the TFA part, this is only compile time tested with
(ls1028ardb_tfa_defconfig).
Signed-off-by: Michael Walle <michael@walle.cc>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
psci_update_dt() is also required if CONFIG_ARMV8_PSCI is set, that is,
if u-boot is the PSCI provider.
Guard the check which is intended to call into the PSCI implementation
in the secure firmware, by the proper macro SEC_FIRMWARE_ARMV8_PSCI.
Mark the function as weak because - unfortunately - there is already
a stub of the same function in arch/arm/mach-rmobile/psci-r8a779a0.c
which does not the same as the common one.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The impedance of the QSPI PCB lines on the sama7g5ek is 50 Ohms.
Align the output impedance of the QSPI0 HSIOs by setting a medium drive
strength which corresponds to an impedance of 56 Ohms when VDD is in the
3.0V - 3.6V range. The high drive strength setting corresponds to an
output impedance of 42 Ohms on the QSPI0 HSIOs.
This is just a fine tunning. The memory that we have populated on sama7g5ek
works fine even with high drive strength, but it's better to adjust it and
use medium instead, in case some other flashes with higher frequencies are
tested.
Suggested-by: Mihai Sain <mihai.sain@microchip.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
QSPI1 used the clock of QSPI0, fix it.
Fixes: 5eecc37bb1 ("ARM: dts: at91: sama7g5: Add QSPI0 and OSPI1 nodes")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
This commit removes the default reset driver for armv7, since
it is no longer needed due to the presence of the SYSRESET driver.
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
This commit adds a condition to the Makefile so that whenever the SYSRESET
option is chosen in the configuration, the default reset driver is ignored.
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
As removal of nds32 has been ack'd for the Linux kernel, remove support
here as well.
Cc: Rick Chen <rick@andestech.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Add a set of combined tests for the bootdev, bootflow and bootmeth
commands, along with associated functionality.
Expand the sandbox console-recording limit so that these can work.
These tests rely on a filesystem script which is not yet added to the
Python tests. It is included here as a shell script.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is helpful to be able to try out bootstd on sandbox, using host files.
This is easier than using a block device, which must have a filesystem,
partition table, etc.
Add a new driver which provides this feature. For now it is not used in
tests, but it is likely to be useful.
Add notes in the devicetree also, but don't disturb the tests.
Signed-off-by: Simon Glass <sjg@chromium.org>
Prepare to use ADC channel 1 to check the hardware revision of the board:
- add u-boot dts include with saradc node
Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20220424082159.757622-6-adeep@lexina.in
There is a Kconfig for this erratum, but it is ignored for armv8.
Respect it.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Unless you have a spare Apple Silicon machine, getting access to
the serial port on Apple Silicon machines requires special
hardware. Given that most machines come with a built-in screen
the framebuffer is likely to be the most convenient output device
for most users. While U-Boot will output to both serial and
framebuffer, OSes might not. Therefore set stdout-path to point
at /chosen/framebuffer when a keyboard is connected to the machine.
This behaviour can be overridden by setting the "stdout" variable
in the U-Boot environment. I addition to that keep the serial
console as the default when running under the m1n1 hypervisor.
The m1n1 hypervisor virtualizes the serial port such that it
can be easily accessed from any other machine with a USB port.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Janne Grunau <j@jannau.net>
Tested-by: Janne Grunau <j@jannau.net>
Since COUNTER_FREQUENCY is obselete, so set cntfrq_el0 if
CONFIG_COUNTER_FREQUENCY is valid
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@vrull.eu>
Set default COUNTER_FREQUENCY according to config header file
under include/configs/
i.MX6UL/ULL/7D/8QM/8QXP all has system counter frequency run at 8MHz,
so set default value for them.
SUNXI/EXYNOS/ROCKCHIP_RK3128/ROCKCHIP_RK3288/ROCKCHIP_RK322X/ROCKCHIP_RK3036
at 24MHz. ARCH_LX2160A at 25MHz
ARCH_ZYNQMP at 100MHz
Fix wrong environment.h and remove DECLARE_GLOBAL_DATA_PTR
Fixes: 30e39ac7c9 (imx: imx7 Support for Manufacturing Protection)
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Gaurav Jain <gaurav.jain@nxp.com>
Update the Kconfig and Makefile to allow build for iMX8M and
restrict the build only in u-boot.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Gaurav Jain <gaurav.jain@nxp.com>
Add support for OF-LIST to common imx8mp-u-boot.dtsi so that it can
be used with boards that have multiple DTB's.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Teresa Remmet <t.remmet@phytec.de>
Cc: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
If .bss does not immediately follow the end of the image, then
CONFIG_SPL_SEPARATE_BSS must be selected. Typically, the location of bss
is specified by using CONFIG_SPL_BSS_START_ADDR in a linker script. On
these arches, CONFIG_SPL_SEPARATE_BSS should be enabled. If there is an
option to use an alternate boot script (e.g. CONFIG_SPL_LDSCRIPT is just
a default), just imply. If there is not, select.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Sync BeagleBone dts files & TPS dtsi files with Linux v5.17 and include
the SanCloud BBE Extended WiFi dts added in v5.18-rc1. Also pull in
changes to am33xx-l4.dtsi needed to support the BeagleBone Blue.
The change to use the cpsw switch driver (commit c477358e66a3 in Linux)
is excluded from the sync as u-boot does not recognise the new
compatible string.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
Implement arch_env_get_location() instead of env_get_location(), so that
the env_get_location() can be implemented on board level and override the
arch_env_get_location() architecture defaults.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Adam Ford <aford173@gmail.com>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Marek Behún <marek.behun@nic.cz>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Tommaso Merciai <tomm.merciai@gmail.com>
Cc: Vladimir Oltean <vladimir.oltean@nxp.com>
Implement arch_env_get_location() instead of env_get_location(), so that
the env_get_location() can be implemented on board level and override the
arch_env_get_location() architecture defaults.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Adam Ford <aford173@gmail.com>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Marek Behún <marek.behun@nic.cz>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Tommaso Merciai <tomm.merciai@gmail.com>
Cc: Vladimir Oltean <vladimir.oltean@nxp.com>
The 4 GiB boundary is at 0xffffffff+1 , not at 0x80000000, fix this.
The PHYS_SDRAM of i.MX8M is at 0x40000000 , so to restrict ram_top
below 4 GiB, the ram_top has to be set to 0xffffffff as it is not
an offset from the start of PHYS_SDRAM, but rather a physical address
marking the topmost allowed DRAM address.
Fixes: e27bddff4b ("imx8m: Restrict usable memory to space below 4G boundary")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Frieder Schrempf <frieder.schrempf@kontron.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
There are no users of the imx6_pcie_toggle_power and imx6_pcie_toggle_reset
weak overrides and as these functions are able to be handled now via dt
properties lets remove these.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
If vpcie-supply is defined by device-tree use that if
CONFIG_PCIE_IMX_POWER_GPIO is not defined.
Note that after this the following boards which define
CONFIG_PCIE_IMX_POWER_GPIO in their board header file as well as their
device-tree should be able to remove CONFIG_PCIE_IMX_PERST_GPIO without
consequence:
- mx6sabresd
- mx6sxsabresd
- novena
Note that the ge_bx50v3 board uses CONFIG_PCIE_IMX_POWER_GPIO and does
not have vpcie-supply defined in it's pcie node in the dt thus removing
CONFIG_PCIE_IMX_POWER_GPIO globally can't be done until that board adds
vpcie-supply.
Cc: Ian Ray <ian.ray@ge.com> (maintainer:GE BX50V3 BOARD)
Cc: Sebastian Reichel <sebastian.reichel@collabora.com> (maintainer:GE BX50V3 BOARD)
Cc: Fabio Estevam <festevam@gmail.com> (maintainer:MX6SABRESD BOARD)
Cc: Marek Vasut <marex@denx.de> (maintainer:NOVENA BOARD)
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The Colibri PXA270 has been end-of-life since quite a while and would
require more and more maintenance (e.g. DM conversions).
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
The GW74xx is based on the i.MX 8M Plus SoC featuring:
- LPDDR4 DRAM
- eMMC FLASH
- Gateworks System Controller
- PCIe Gen 3.0 switch (build option)
- USB 3.0 HUB
- USB Type-C front panel connector
- GPS
- 3-axis accelerometer
- CAN bus
- 6x GbE RJ45 front-panel jacks
- 1x IMX8M FEC RGMII GbE (with Passive PoE)
- 5x IMX8M EQOS RGMII 6 port GbE Switch
(1x with 802.3af class 5 Active PoE)
- RS232/RS485/RS422 serial transceiver
- MIPI header (DSI/CSI/GPIO/PWM/I2S)
- DigI/O header (UART/GPIO/I2C/ADC)
- 802.11ac WiFi
- Bluetooth BLE
- 3x MiniPCIe sockets with PCI/USB
- 1x M.2 Socket with USB2.0, PCIe, and dual-SIM
- PMIC
- Wide range DC input supply (8V to 60V DC)
Do the following to add support for this and future imx8mp-venice boards:
- add dts
- add DRAM config
- add PMIC config
- add IMX8MP support in spl.c and venice.c
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Use the common GSC driver.
This allows us to do some additional cleanup:
- use the GSC driver functions
- move waiting for the EEPROM to the SPL int (it will always be ready
after this)
- move eeprom functions into eeprom file and elimate GSC_I2C_BUS
- eliminate some redundant EEPROM reads (the EEPROM must be read in
SPL before relocation, in SPL after relocation, and in U-Boot init.
All subsequent uses can use the global structure)
- remove unnecessary header files and alphabatize includes
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The TI DP83867 phy has been replaced with the MaxLinear GPY111 phy
due to part availability. Add support for it:
- increase post-reset time to 300ms per datasheet
- add tx-delay/rx-delay config
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Add gpio hog support for board-specific gpio lines:
- put hogs in u-boot.dtsi so as to keep the regular dts files
in sync with the kernel. The hogs will not be put in the kernel
as that makes them un-usable by userspace as well as
re-initializes them to dt defaults overriding changes which may
have been done by bootloader commands.
- specify gpio names and initial config
- enable GPIO_HOG
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Use the common GSC driver.
This allows us to do some additional cleanup:
- rename gsc{.c,.h} to eeprom{.c.h} for clarity
- collapse eeprom_get_dev
- remove unnecessary header files and alphabatize includes
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Drop Apalis iMX8X platform as it never left sample state and is no
longer supported.
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Add DT bindings for a subset of GPCv2 which handles USB and PCIe PDs,
HSIOMIX PD controller and missing USB PD properties. This is required
to bring up the DWC3 USB controller up.
This is based on linux next and patches which are still pending
review, but which are likely going to be part of Linux 5.19:
b2d67d7bdf74 ("arm64: dts: imx8mp: disable usb3_phy1")
290918c72a29 ("arm64: dts: imx8mp: Add memory for USB3 glue layer to usb3 nodes")
https://www.spinics.net/lists/arm-kernel/msg958501.html
Tested-By: Tim Harvey <tharvey@gateworks.com> #imx8mp-venice-gw74xx
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
The arch/arm/include/asm/arch-imx8m/power-domain.h is not included
anywhere except in drivers/power/domain/imx8m-power-domain.c, just
inline the content and drop the header. No functional change.
Tested-By: Tim Harvey <tharvey@gateworks.com> #imx8mp-venice-defconfig
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
The div loop uses reassign and reuse parent_rate, which causes
the parent rate reference to be wrong after the first loop, the
resulting clock becomes incorrect for div != 1.
Fixes: 829e06bf41 ("imx8ulp: clock: Add MIPI DSI clock and DCNano clock")
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
DT node name should be generic, therefore rename atsha204a@64 to crypto@64.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Implement write support for Security OTP values via mailbox API commands
MBOX_CMD_OTP_WRITE_32B and MBOX_CMD_OTP_WRITE.
Write support for North and South Bridge OTPs are not implemented as these
OTPs are already burned in factory with some data.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
U-Boot SPL is on 32-bit mvebu executed by the BootROM. And BootROM expects
that U-Boot SPL returns execution back to the BootROM. Vectors during
execution of U-Boot SPL should not be changed as BootROM does not expect it
and uses its own vectors. So do not overwrite vectors in SPL build.
Signed-off-by: Pali Rohár <pali@kernel.org>
Armada 385 contains 64 lines of HD eFuse and 2 lines of LD eFuse. HD eFuse
is used for secure boot and each line is 64 bits long + 1 lock bit. LD
eFuse lines are 256 bits long + 1 lock bit. LD 0 line is reserved for
Marvell Internal Use and LD 1 line is for General Purpose Data. U-Boot
already contains HD eFuse reading and programming support.
This patch implements LD eFuse reading support. LD 0 line is mapped to
U-Boot fuse bank 64 and LD 1 line to fuse bank 65.
LD 0 Marvell Internal Use line seems that was burned in factory with some
data and can be read by U-Boot fuse command:
=> fuse read 64 0 9
LD 1 General Purpose Data line is by default empty and can be read by
U-Boot fuse command:
=> fuse read 65 0 9
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
uDPU is a bit of a specific device in that it does not have any copper
ports nor any ethernet PHY-s but 2 SFP ports.
This is an issue since MVNETA requires a PHY phandle or a fixed-link to
be defined under its node.
Since U-boot has no SFP support this is reasonable in order to know how
to configure the MAC.
However this also means that networking does not work on uDPU at all
currently, and fails with:
uDPU>> dhcp
Could not get PHY for neta@30000: addr 0
phy_connect failed
Could not get PHY for neta@40000: addr 1
phy_connect failed
So, to provide working networking using only SFP-s let add the fixed-link
at 1G which is much more common than 2.5G SFP-s as well as disable the
TX_DISABLE pins like done on Armada 7040 and 8040 platforms.
Since uDPU is not using any of the GPIO-s on the SB controller for any
purpose other than GPIO, a call to the pinctrl must be made in order for
it to get probed and thus register the SB GPIO bank, otherwise SB GPIO-s
are not registered at all.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
It is not possible for the A53 core (on which U-Boot is running) to read it
directly. For this purpose Marvell defined mbox API for sending OTP
commands between CM3 and A53 cores.
Implement these Marvell fuse reading mbox commands via U-Boot fuse API.
Banks 0-43 are used for accessing Security OTP (44 rows with 67 bits via 44
banks and words 0-2).
Note that of the 67 bits, the 3 upper bits are: 1 lock bit and 2
auxiliary bits (meant for testing during the manufacture of the SOC, as
I understand it).
Also note that the lock bit and the auxiliary bits are not readable
via Marvell commands.
With CZ.NIC's commands the lock bit is readable.
Write support is not implemented yet.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Allow to specify input parameters, define all available mbox commands
supported by CZ.NIC's secure firmware and also Marvell's fuse.bin firmware
and fix parsing response from Marvell OTP commands.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Generic A3720 mbox code is currently in Turris Mox specific board file
board/CZ.NIC/turris_mox/mox_sp.c. Move it to board independent arch file
arch/arm/mach-mvebu/armada3700/mbox.c.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Implement reading NB and SB fuses of Armada 37xx SOC via U-Boot fuse API.
Banks 0-43 are reserved for accessing Security OTP (not implemented yet).
Bank 44 is used for accessing North Bridge OTP (69 bits via words 0-2).
Bank 45 is used for accessing South Bridge OTP (97 bits via words 0-3).
Write support is not implemented yet because it looks like that both North
and South Bridge OTPs are already burned in factory with some data. The
meaning of some bits of North Bridge is documented in WTMI source code.
The meaning of bits in South Bridge is unknown.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
When storing the UBoot Environment in for example EXT4,
the U-Boot build is broken for several reasons:
1. armada-385-turris-omnia-u-boot.dtsi will not allow
CONFIG_ENV_OFFSET and CONFIG_ENV_SIZE to be undefined
2. armada-37xx/board.c ft_board_setup function does not
exist if CONFIG_ENV_IS_IN_SPI_FLASH is not defined
This commit changes these files so that selecting a
different location for the environment is possible.
Signed-off-by: Rogier Stam <rogier@unrailed.org>
Reviewed-by: Pali Rohár <pali@kernel.org>
Use this larger boundary to ensure that linker lists at least start on the
maximum possible alignment boundary. See also the CONFIG_LINKER_LIST_ALIGN
setting, but that is host-arch-specific, so it seems better to use the
largest value for every host architecture.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present fputc() is used before the console is available, then write()
is used. These are not compatible. Since fputc() buffers internally it is
better to use the write(), so that a partial line is immediately
displayed.
This has a slight effect on performance, but we are already using write()
for the vast majority of the output with no obvious impacts.
Signed-off-by: Simon Glass <sjg@chromium.org>
The DT node name pattern in mmc-controller.yaml for mmc
is "^mmc(@.*)?$". The Rockchip mmc nodes have been synced
with Linux, so update the boot_devices constants as well.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In order to sync rk3288.dtsi from Linux it needed to
move all u-boot specific properties in separate dtsi files.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In order to update the DT for rk3288
sync the power domain dt-binding header.
This is the state as of v5.17 in Linux.
Change location to be more in line with other SoCs.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In order to sync rk322x.dtsi from Linux, move all
U-boot specific properties in separate dtsi files.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
MK808 is a RK3066-based board with 1 USB host and 1 USB OTG port,
HDMI and a micro-SD card slot. It also includes on-board NAND
and 1GB of SDRAM.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
MK808 is a RK3066-based board with 1 USB host and 1 USB OTG port,
HDMI and a micro-SD card slot. It also includes on-board NAND
and 1GB of SDRAM. Add rk3066a-mk808.dts. Move U-boot specific
things in a rk3066a-mk808-u-boot.dtsi file.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In the Linux DT the file rk3xxx.dtsi is shared between
rk3066 and rk3188. Add rk3066a.dtsi. Move U-boot specific
things in a rk3066a-u-boot.dtsi file.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Move the include for rk3xxx-u-boot.dtsi to rk3188-u-boot.dtsi
to stay in line with U-boot dtsi files.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The file rk3xxx-u-boot.dtsi was original only for rk3188 and SPL.
With rk3066 added some nodes are also needed in TPL,
so change them to u-boot,dm-pre-reloc
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add the clock driver for the rk3066 platform.
Derived from the rk3288 and rk3188 driver it
supports only a bare minimum to bring up the system
to reduce the TPL size for:
SDRAM clock configuration.
The boot devices NAND, EMMC, SDMMC, SPI.
A UART for the debug messages (fixed) at 115200n8.
A SARADC for the recovery button.
A TIMER for the delays (fixed).
There's support for two possible frequencies,
the safe 600MHz which will work with default pmic settings and
will be set to get away from the 24MHz default and
the maximum of 1.416Ghz, which boards can set if they
were able to get pmic support for it.
After the clock tree is set during the TPL probe
there's no parent update support.
In OF_REAL mode the drivers ns16550.c and dw-apb-timer.c
obtain the (fixed) clk_get_rate from the clock driver
instead of platdata.
The rk3066 cru node has a number of assigned-clocks properties
that call the .set_rate() function. Add them to the list so that
they return a 0 instead of -ENOENT.
Signed-off-by: Paweł Jarosz <paweljarosz3691@gmail.com>
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
grf is needed by various drivers for rk3066 soc.
Signed-off-by: Paweł Jarosz <paweljarosz3691@gmail.com>
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Not all Rockchip SoC models use the ARM arch timer.
Call the function timer_init() only when
CONFIG_SYS_ARCH_TIMER is available.
Use the call condition IS_ENABLED to increase
build coverage and make the code easier to read.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Rockchip SoCs rk3066/rk3188 have no CONFIG_ROCKCHIP_STIMER_BASE
defined. Currently there's no exception in TPL. Make this more
generic and compile the code inside the function rockchip_stimer_init()
only when CONFIG_ROCKCHIP_STIMER_BASE is available.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Rockchip SoCs rk3066/rk3188 have no CONFIG_ROCKCHIP_STIMER_BASE
defined. Currently only rk3188 has an exception in SPL. Make this more
generic and compile code inside the function rockchip_stimer_init()
only when CONFIG_ROCKCHIP_STIMER_BASE is available.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
- DM9000 DM support
- tftp server bug fix
- mdio ofnode support functions
- Various phy fixes and improvements.
[trini: Fixup merge conflicts in drivers/net/phy/ethernet_id.c
drivers/net/phy/phy.c include/phy.h]
It seems like there was some merge error when first cleaning up and
sharing this function. We have both an inline version of the function
in include/tables_csum.h and a non-inline version in lib/tables_csum.c.
Rework things so that we only have the non-inline version (due to number
of calls, we should not inline this).
Fixes: 1befb38b86 ("x86: Move table csum into separate file")
Fixes: 2b445e4d31 ("x86: Move table csum into separate header")
Cc: Alexander Graf <agraf@csgraf.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This adds a test to ensure that puts is equivalent to putc called in a
loop. We don't verify the contents of the message to avoid having to
record console output a second time (though that could be added in the
future). The globals are initialized to non-zero values to avoid a
warning; in particular, the character count is off-by-one (but we always
make relative measurements).
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The M1 Ultra consists of two M1 Max dies. The second die's I/O is at
a consistent offset of 0x2000000000.
Signed-off-by: Janne Grunau <j@jannau.net>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
The GW7903 is based on the i.MX 8M Mini SoC featuring:
- LPDDR4 DRAM
- eMMC FLASH
- microSD socket with voltage select support
- Gateworks System Controller
- M.2 A-E Socket with USB2.0 and PCIe
- MiniPCIe Socket with PCIe, USB2.0, and SIM
- IMX8M FEC
- RS232/RS485/RS422 serial transceiver
- LIS2DE12 3-axis accelerometer
- front panel LED's
- off-board isolated digital I/O
- Wide range DC power input
- 802.3at PoE
- PMIC
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
This is the only place where i.MX8M code does SMCCC call, remove it.
The output has little value as it prints some part of commit ID, and
worse, if there is no SMC handler installed, the code outright hangs
or crashes the system.
By removing this one instance of SMCCC call, U-Boot no longer depends
on SMC handlers and can boot without hanging in any case. If there is
a need to dump this commit ID, use CMD_SMC instead and do 'smc' call
from U-Boot shell or scripts instead of hard-coding SMCCC dependency
into architecture code. This particular code can be replaced by:
=> smc 0xc2000003 0 0 0 0 0 0
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Enable instruction cache early on to speed up the boot process on i.MX8M.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Add new board based on the Toradex Verdin iMX8M Mini SoM, the MX8Menlo.
The board is a compatible replacement for i.MX53 M53Menlo and features
USB, multiple UARTs, ethernet, LEDs, SD and eMMC.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Max Krummenacher <max.krummenacher@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
The Linux kernel moved dt-bindings/pinctrl/pins-imxrt to the device tree
This patch move it in U-Boot as well.
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
In Linux IMX and IMXRT use the device tree to hold the anatop address.
The anatop is used in clock drivers as it controls the internal PLLs
This will move the macro from asm/arch-imxrt to the device tree.
This presumably should also be done with the other IMX boards as well.
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
The FlexSPI NOR boot offset does not require any special handling,
the image_offset is correct in either case (0x1000 for FlexSPI NOR
and 0x8000 for SD/eMMC) and the offset of u-boot.itb from the start
of flash.bin is always 0x58000 on MX8MN/MX8MP, which matches the
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR * 512 - 0x8000 in case
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x300, which is always the
case on MX8MN/MX8MP.
The CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR is really overloaded in
case of the MX8MN/MX8MP, but fixing that needs additional plumbing.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
The GW7902-C revision adds an ADC for the VDD_5P0 voltage rail.
Add register definitions for it.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Add support for Data Modul i.MX8M Mini eDM SBC board. This is an
evaluation board for various custom display units. Currently
supported are serial console, ethernet, eMMC, SD, SPI NOR,
USB host and USB OTG.
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
This macro currently supports only one parameter. Based on Linux iopoll,
let's extend read_poll_timeout common API to allow multiple variable
parameters.
Signed-off-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
Add init_nand_clk to enable gpmi nand clock. Since i.MX8M not use CCF,
so we still use legacy mode to configure the clock.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Set the BYPASS ID SWAP bit (GPR10 bit 1).
The ID SWAP function randomly make TZASC grant non-secure access to
secure memory. TZASC ID SWAP should be bypassed by setting the bit
TZASC_ID_SWAP_BYPASS(bit 1) in IOMUX_GPR10 register.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Turns out on certain carrier boards (e.g. Iris V2) and under certain
circumstances (e.g. after a software reset) the SD card may have been
left in a strange state which later failed as follows:
Colibri iMX6ULL # mmc dev 0
Card did not respond to voltage select! : -110
Fix this as follows:
- Re-name the signaling voltage rail regulator from vmmc to vqmmc.
- Fix the name of the GPIO property to gpios.
- Specify 4-bit bus width, no write-protect capability and no 1.8
volt signaling voltage capability.
- Fix the clock vs. command pull-up vs. push-pull configuration.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Now that it is possible to use regulator-fixed-clock make use
of it. This makes U-Boot detect the PHY on first cold-boot.
This commit also adjusts the code in setup_fec and follows
how it is done in mx6ullevk.c
This commit also slows down the boot-process by about 150ms
as it now waits for the regulator-fixed-clock voltage that
drives the PHY to go up.
If you rely on very fast boot-speeds and don't need ethernet
for your boot-process you can safely revert the changes on
imx6ull-colibri.dtsi
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Explicitly use the atf-bl31 type for the bl31.bin atf-blob. This uses
the path from the BL31 environment variable, if defined.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
The EFI memory init uses gd->ram_top for conventional memory. In
current implementation, the ram_top is below optee address. This cause
grub failed to allocation memory for initrd.
The change updates DDR bank setup functions to place the u-boot at top
DDR in 4GB space.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Need to drop phy-reset-gpios before booting linux, this property
is legacy property and replaced with reset-gpios.
If provide both, kernel would failed to request the same gpio twice
and cause fec not work.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The extcon is an decrepted property and not used by upstream Linux and
NXP 5.10 kernel, so we remove it before kicking linux in case it is in
dts. Otherwise distro kernel will not able to have usb function.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Beside the fused modules on iMX8MP Lite, this part has also fused
GPU3D/2D, LVDS and MIPI DSI.
So we have to disable them for kernel and also disable MIPI DSI
in u-boot DTS for splash screen at runtime.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Wait 1ms before issuing the first MRS command to write DDR3 Mode
registers.
There is a requirement to wait a minimum time before issuing command to
the DDR3 device, according to the JEDEC standard this time is 500us
(after RESET_n is de-asserted until CKE becomes active) + tXPR (Reset
CKE Exit time, maximum value 360ns).
It seems that for some reason this is not enforced by the MMDC
controller.
Without this change we experienced random memory initialization failures
with about 2% boot failure rate on specific problematic boards, after
this change we were able to do more than 10.000 power-cycle without a
single failure.
Fixes: fe0f7f7842 ("mx6: add mmdc configuration for MX6Q/MX6DL")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The current DDR write level calibration routine always overwrite
the ralat/walat fields to their maximum value, just save
the existing values at the beginning of the calibration routine
and restore it at the end.
In case the delay is estimated by the user to be more than one cycle the
walat should be configured according to that, this is not
automatically done. From the i.MX6 RM:
The user should read the results of the associated delay-line at
MPWLDECTRL#[WL_DL_ABS_OFFSET#] and in case the user estimates that the
reasonable delay may be above 1 cycle then the user should indicate it at
MPWLDECTRL#[WL_CYC_DEL#]. Moreover the user should indicate it in
MDMISC[WALAT] field. For example, if the result of the write leveling calibration
is 100/256 parts of a cycle, but the user estimates that the delay is above 2 cycles
then MPWLDECTRL#[WL_CYC_DEL#] should be configured to 2, so the total
delay will be 2 and 100/256 parts of a cycle
Probably it would just possible to not overwrite the mdmisc register in
the first place, since this is not present in the write_level_calib() example
in NXP AN4467 nor in the i.MX6 RM (44.11.6.1 Hardware Write Leveling
Calibration).
Fixes: d339f16911 ("arm: imx6: Add DDR3 calibration code for MX6 Q/D/DL")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Enable multiple storages for u-boot env:
MMC or SPI flash or NOWHERE for usb
so u-boot can runtime select the storage flash according to boot device.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The TEE memory should be reserved when TEE is present, so need
to runtime update dram bank and memory information according to
tee present or not.
Signed-off-by: Ji Luo <ji.luo@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Enable wdog_ad interrupt being triggered by CMC1 to CM33 to let CM33
know A35 reset and reinitialize rpmsg.
Clear wdog_ad and AD_PERIPH reset interrupt after A35 up, otherwise
M33 will always receive interrupt.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Assign the LPAV owner to RTD, and assign LPAV masters and peripherals
to APD. So except the masters and peripherals, other resources
(like DDR, cgc2, pcc5) in LPAV won't be reset during reboot and suspend.
No needs to initialize DDR again after reboot.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Enable MU0_B clk by default. When M33 image is loaded by Jlink,
the previous method not enable MU0_B clk and not able to communicate
with M33, so let's enable it by default.
And we not put it under kernel dts, because it conflicts with i.MX8QM
suspend/resume logic which requires large change.
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When reset with dual boot mode, the LPAV domain won't power down
due to its master is not assigned to APD. So the NICLPAV keeps the
last setting to use PLL4PFD1. So before SPL initialize the PLL4,
we need to switch NICLPAV to FRO192, otherwise system will hang.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When M33 is LPAV owner in dual boot, DDR, PCC5, CGC2 won't be reset
during APD reset. So no need to init DDR again after reboot, but need to
reconfigure the PLL4 PFD/PFDDIV/LPAV NIC etc, because kernel may
change or disable some of them.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add a new ddr script, defconfig for ND
Configure the clock for ND mode
changing A35 to 960MHz for OD mode
Update NIC CLK for the various modes
Introduce clock_init_early/late, late is used after pmic voltage
setting, early is used in the very early stage for upower mu, lpuart and
etc.
Note: NIC runs at 324MHz, 442MHz has some random kernel hang issue with
cpuidle enabled now.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add i3c controller clock enable/disable function for imx8ulp.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
