As part of various code clean-ups we have on occasion missed removing
unused header files. None of these files are referenced anywhere else
at this point.
Signed-off-by: Tom Rini <trini@konsulko.com>
It seems like the header inclusion guard for some Uniphier DDR PHY
header was misspelled.
Make the preprocessor symbol for the #ifndef and #define lines the
same, so that the double inclusion protection works as expected.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
It seems like the header inclusion guards for some IMX related headers
were misspelled or got out of sync.
Make the preprocessor symbols for the #ifndef and #define lines the
same, so that the double inclusion protection works as expected.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This platform is currently unmaintained and untested, so remove it.
Further, as it is the only TI816X SoC example, remove related files as
well.
Signed-off-by: Tom Rini <trini@konsulko.com>
Apple's M2 Pro/Max SoC are somewhat similar to the M1 Pro/Max but
need a tweaked memory map. USB, NVMe, UART and WDT are working
with the existing drivers.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
K3 GP devices allows booting the secure binaries on them by bypassing
the x509 header on them.
ATF and OPTEE firewalling required the rproc_load to be called before
authentication. This change caused the failure for GP devices that
strips off the headers. The boot vector had been set before the headers
were stripped off causing the runtime stripping to fail and stripping
becoming in-effective.
Separate out the secure binary check on GP/HS devices so that the
boot_vector could be stripped before calling rproc_load. This allows
keeping the authentication later when the cluster is on along with
allowing the stripping of the binaries in case of gp devices.
Fixes: 1e00e9be62 ("arm: mach-k3: common: re-locate authentication for atf/optee")
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
When booting with HS silicon, the system firmware image is 278270, which
is slightly larger than currently allocated amount.
This can cause unexpected behavior if this overlap interferes with other
things in memory, so increase this with a slightly margin added as well
to avoid any boot issues that can appear after system firmware gets
loaded.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
In non-combined boot flow for K3, all the firewalls are locked by default
until sysfw comes up. Rom configures some of the firewall for its usage
along with the SRAM for R5 but the PSRAM region is still locked.
The K3 MCU Scratchpad for j721e was set to a PSRAM region triggering the
firewall exception before sysfw came up. The exception started happening
after adding multi dtb support that accesses the scratchpad for reading
EEPROM contents.
The commit changes R5 MCU scratchpad for j721e to an SRAM region.
Old Map:
┌─────────────────────────────────────┐ 0x41c00000
│ SPL │
├─────────────────────────────────────┤ 0x41c40000 (approx)
│ STACK │
├─────────────────────────────────────┤ 0x41c85b20
│ Global data │
│ sizeof(struct global_data) = 0xd8 │
├─────────────────────────────────────┤ gd->malloc_base = 0x41c85bfc
│ HEAP │
│ CONFIG_SYS_MALLOC_F_LEN = 0x70000 │
├─────────────────────────────────────┤ CONFIG_SPL_BSS_START_ADDR
│ SPL BSS │ (0x41cf5bfc)
│ CONFIG_SPL_BSS_MAX_SIZE = 0xA000 │
└─────────────────────────────────────┘ CONFIG_SYS_K3_BOOT_PARAM_TABLE_INDEX
(0x41cffbfc)
New Map:
┌─────────────────────────────────────┐ 0x41c00000
│ SPL │
├─────────────────────────────────────┤ 0x41c40000 (approx)
│ EMPTY │
├─────────────────────────────────────┤ 0x41c81920
│ STACK │
│ SPL_SIZE_LIMIT_PROVIDE_STACK=0x4000 │
├─────────────────────────────────────┤ 0x41c85920
│ Global data │
│ sizeof(struct global_data) = 0xd8 │
├─────────────────────────────────────┤ gd->malloc_base = 0x41c859f0
│ HEAP │
│ CONFIG_SYS_MALLOC_F_LEN = 0x70000 │
├─────────────────────────────────────┤ CONFIG_SPL_BSS_START_ADDR
│ SPL BSS │ (0x41cf59f0)
│ CONFIG_SPL_BSS_MAX_SIZE = 0xA000 │
├─────────────────────────────────────┤ 0x41cff9fc
│ NEW MCU SCRATCHPAD │
│ SYS_K3_MCU_SCRATCHPAD_SIZE = 0x200 │
└─────────────────────────────────────┘ CONFIG_SYS_K3_BOOT_PARAM_TABLE_INDEX
(0x41cffbfc)
Fixes: ab977c8b91 ("configs: j721s2_evm_r5: Enable support for building multiple dtbs into FIT")
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
[n-francis@ti.com: SRAM allocation addressing diagram]
Signed-off-by: Neha Francis <n-francis@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Kamlesh Gurudasani <kamlesh@ti.com>
When building for secure devices using non-buildman based image generation
the signed tispl.bin file is called tispl.bin_HS. Also build the unsigned
tispl.bin file as expected.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
To avoid using static setting for ECC enabled DDR size, switch
to calculate DDR size from DDRC setting
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Update the DDR init flow for multi-setpoint support on i.MX93. A new
fsp_cfg struct need to be added in the timing file to store the diff
part of the DDRC and DRAM MR register for each setpoint.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add 625M bypass clock that may be used DRAM 625M
bypass mode support.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
According to DDRPHY errata, the Rank-to-Rank Spacing and tphy_rdcsgap
specification does not include the Critical Delay Difference (CDD) to
properly define the required rank-to-rank read command spacing after
executing PHY training firmware.
Following the errata workaround, at the end of data training, we get
all CDD values through the MessageBlock, then re-configure the DDRC
timing of WWT/WRT/RRT/RWT with comparing MAX CDD values.
Signed-off-by: Ye Li <ye.li@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Currently bootaux only supports to boot M33 core from TCM. Since ATF
has changed to use x2 parameter for M33 image address, update the
bootaux command to use input address, so we can support boot from
any possilbe address like TCM, DDR, Flexspi NOR.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
According to datasheet, iMX93 has fused parts with CORE1 or NPU or
both disabled. So update code to support it, the kernel device tree
runtime update will be added in future patches.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Config the A55 alt root clock to 500MHz(LD mode frequency)
by default. Normally, this clock root is only used as an
intermediate clock soure for A55 core/dsu when change the
ARM PLL frequency.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The HW_CTRL_SEL should be cleared when configuring PLL to avoid
potential glitch
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Support print reset cause. Since SRSR is not accessible from non-secure
world, so first save it to grp0, then read it in non-secure world.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The MAC addresses are hard coded for bring up. Change it to support
reading from fuse.
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
OPTEE memory region is set secure access only in ATF with configuration
to TRDC, and need to remove it from U-Boot, otherwise U-Boot and Kernel
may crash when accessing the memory
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Move imx8 sci header file to include/firmware/imx, then we could
use build macro to reuse some i.MX8 drivers for i.MX9, such as
drivers/cpu/imx8_cpu.c.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Stefano Babic <sbabic@denx.de>
Commit 1a7904fdfa ("mmc: fsl_esdhc_imx: Use esdhc_soc_data
flags to set host caps") exposed the following SD card error:
U-Boot 2023.04-00652-g487e42f7bc5e (Apr 05 2023 - 22:14:21 -0300)
CPU: Freescale i.MX7D rev1.0 1000 MHz (running at 792 MHz)
CPU: Commercial temperature grade (0C to 95C) at 35C
Reset cause: POR
Model: Freescale i.MX7 SabreSD Board
Board: i.MX7D SABRESD in non-secure mode
DRAM: 1 GiB
Core: 100 devices, 19 uclasses, devicetree: separate
PMIC: PFUZE3000 DEV_ID=0x30 REV_ID=0x10
MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... Card did not respond to voltage
select! : -110
*** Warning - No block device, using default environment
The reason of the problem, as explained by Ye Li:
"When UHS is enabled in defconfig, the usdhc1 node in imx7d-sdb.dts does
not configure pad for VSELECT, also the data pad should be set to
100Mhz/200Mhz pin states."
Apply these changes into u-boot.dtsi for now. When these changes
reach the Linux mainline imx7d-sdb, they can be dropped from u-boot.dtsi.
This fixes UHS mode on the imx7d-sdb board.
Suggested-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Stop polluting the architecture directory with driver specific code,
move it into driver where it should be. Split the code slightly so
the MX8MM/MX8MN fuse readout and programming and MX8MP fuse readout
and programming are in their separate functions, and called in case
of matching SoC.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
It seems like the ROM log events for the iMX8M are not fully covered by
AN12853 i.MX ROMs Log Events, Rev. 0, May 2020. On iMX8M the ROM event
ID 0x82 seems to use parameter0 which stops the parsing because the end
of list is detected too early.
This patch adds ROM event ID 0x82 and skips the next word if ID 0x82 is
parsed.
Fixes: a5ee05cf71 ("ARM: imx: Pick correct eMMC boot partition from ROM log")
Signed-off-by: Fedor Ross <fedor.ross@ifm.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Add sfc and flash node to device tree and config options to enable
support for booting from SPI NOR flash on Radxa ROCK 5 Model B.
Similar to RK3568 the BootRom in RK3588 can read all data and look for
idbloader at 0x8000, same as on SD and eMMC.
Use the rksd format and modify the mkimage offset to generate a bootable
u-boot-rockchip-spi.bin that can be written to 0x0 of SPI NOR flash. The
FIT image is loaded from 0x60000.
=> sf probe
SF: Detected mx25u12835f with page size 256 Bytes, erase size 4 KiB, total 16 MiB
=> load mmc 1:1 10000000 u-boot-rockchip-spi.bin
1492992 bytes read in 129 ms (11 MiB/s)
=> sf update $fileaddr 0 $filesize
device 0 offset 0x0, size 0x16c800
1300480 bytes written, 192512 bytes skipped in 11.103s, speed 137694 B/s
The BROM_BOOTSOURCE_ID value read back when booting from SPI flash does
not match the expected value of 3 (SPINOR) used by other SoCs. Instead a
value of 6 is read back, add a new enum value to handle this new
bootsource id.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Eugen Hristev <eugen.hristev@collabora.com>
Enable pinctrl for sdhci in SPL to support loading of FIT image from SD
and eMMC storage when booting from SPI NOR flash.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Like other Rockchip SoCs, DM_RESET and DM_REGULATOR_FIXED is useful
across RK3588 platform. Select them from arch Kconfig.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add sfc and flash node to device tree and config options to enable
support for booting from SPI NOR flash on Radxa ROCK 3 Model A.
Unlike prior generation SoCs the BootRom in RK3568 can read all data and
look for idbloader at 0x8000, same as on SD and eMMC.
Use the rksd format and modify the mkimage offset to generate a bootable
u-boot-rockchip-spi.bin that can be written to 0x0 of SPI NOR flash. The
FIT image is loaded from 0x60000.
=> sf probe
SF: Detected mx25u12835f with page size 256 Bytes, erase size 4 KiB, total 16 MiB
=> load mmc 1:1 10000000 u-boot-rockchip-spi.bin
1384448 bytes read in 119 ms (11.1 MiB/s)
=> sf update $fileaddr 0 $filesize
device 0 offset 0x0, size 0x152000
1179648 bytes written, 204800 bytes skipped in 9.901s, speed 143185 B/s
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable pinctrl for sdmmc and sdhci in SPL to support loading of FIT
image from SD and eMMC storage when booting from SPI NOR flash.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable pinctrl for sdmmc and sdhci in SPL to support loading of FIT
image from SD and eMMC storage when booting from SPI NOR flash.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update defconfig for rk3566-radxa-cm3-io with new defaults. Also add
missing supported mmc modes to sdhci node.
Remove the SPL_ROCKCHIP_BACK_TO_BROM=y option, SPL is expected to load
next stage from a FIT image and then jump to next stage not back to
BootRom.
Add CONFIG_SPL_FIT_SIGNATURE=y to let SPL verify an auto generated hash
of FIT images. This help indicate if there is an issue loading any of
the images to DRAM or SRAM.
Extend SPL_MAX_SIZE to 0x40000, SPL is loaded to 0x0 and TF-A is loaded
to 0x40000, use the space in between as SPL_MAX_SIZE.
Add config option to include useful gpio cmd.
Remove the CONFIG_NET_RANDOM_ETHADDR=y option, ethaddr and eth1addr is
set based on cpuid read from OTP.
Filter out assigned-clock props with CONFIG_OF_SPL_REMOVE_PROPS,
U-Boot proper will read and configure assigned-clock props.
Add CONFIG_SYS_NS16550_MEM32=y to use 32bit access of serial register.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add bootph-all prop to xin24m clock node, it is referenced by cru node.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable the PCIe 2x1l 2 device and associated combphy.
On this bus, the Rock5B has an Ethernet transceiver connected.
Signed-off-by: Christopher Obbard <chris.obbard@collabora.com>
[eugen.hristev@collabora.com: minor tweaks]
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
[jonas@kwiboo.se: add PCIe pins]
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add the node for PCIe 2x1l 2 device together with the corresponding
combphy.
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
[eugen.hristev@collabora.com: moved to -u-boot.dtsi, minor
adaptations]
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
[jonas@kwiboo.se: adapt to kernel node]
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable the use of SDMA mode to boost eMMC performance on ROCK Pi 4.
Also add missing flags to indicate the supported MMC modes.
Using mmc read command to read 32 MiB data shows following improvement:
=> time mmc read 10000000 2000 10000
Before: time: 3.178 seconds
After: time: 0.402 seconds
This also enables CONFIG_SPL_FIT_SIGNATURE option to help discover
any possible future issue with loading TF-A into DRAM/SRAM.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable the use of SDMA mode to boost eMMC performance on RockPro64.
Also add missing flags to indicate the supported MMC modes.
Using mmc read command to read 32 MiB data shows following improvement:
=> time mmc read 10000000 2000 10000
Before: time: 3.178 seconds
After: time: 0.402 seconds
This also enables CONFIG_SPL_FIT_SIGNATURE option to help discover
any possible future issue with loading TF-A into DRAM/SRAM.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Loading part of TF-A into SRAM from eMMC using DMA fails on RK3399
similar to other Rockchip SoCs. Checksum validation fails with:
## Checking hash(es) for Image atf-2 ... sha256 error!
Bad hash value for 'hash' hash node in 'atf-2' image node
spl_load_simple_fit: can't load image loadables index 1 (ret = -1)
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###
Add a device tree property, u-boot,spl-fifo-mode, to control when the
rockchip_sdhci driver should disable the use of DMA and fallback on PIO
mode. Same device tree property is used by the rockchip_dw_mmc driver.
In commit 2cc6cde647 ("mmc: rockchip_sdhci: Limit number of blocks
read in a single command") the DMA mode was disabled using a CONFIG
option on RK3588. Revert that and instead disable DMA using the device
tree property for all RK3588 boards, also apply similar workaround for
all RK3399 boards.
Fixes: 2cc6cde647 ("mmc: rockchip_sdhci: Limit number of blocks read in a single command")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Quentin Schulz <foss+uboot@0leil.net> # RK3399 Puma, RK3588 Tiger
The current DT bindings for the rk3588 clock use a different ID than the
one that is supposed to be written to the hardware registers.
Thus, we cannot use directly the id provided in the phandle, but rather
use a lookup table to correctly setup the hardware.
This approach has been implemented already in Linux, by commit :
f1c506d152ff ("clk: rockchip: add clock controller for the RK3588")
Hence, implement a similar approach using the lookup table, and adapt
the existing reset driver to work with SoCs using lookup table.
The file rst-rk3588.c has been copied as much as possible from Linux.
Adapt the clk rk3588 driver as well to bind the reset driver with the
lookup table.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
To be able to initialize the pinctrl correctly at SPL level and read
u-boot proper from SD-Card, the pinctrl must be initialized.
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add USB 2.0 host nodes and PHYs.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Co-developed-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
In current implementation, applications can execute only on R5 core 0.
The boot address for R5 core 1 is not supplied. Pass TCM address for
R5 core 1 based on the argument to fix the issue.
Remove incomplete comment.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/da865717d26648ab7a84345ca8749712efdddee5.1680699999.git.michal.simek@amd.com
The "zynqmp tcminit split" command should halt both cores and not just RPU1
when configuring the TCM memory for split mode.
Signed-off-by: Neal Frager <neal.frager@amd.com>
Link: https://lore.kernel.org/r/20230323082506.31576-1-neal.frager@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add support for Schneider Electric RZ/N1D and RZ/N1S boards, which
are based on the Reneasas RZ/N1 SoC devices.
The intention is to support both boards using a single defconfig, and to
handle the differences at runtime.
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The RZ/N1 is a family of SoC devices from Renesas, featuring:
* ARM Cortex-A7 CPU (single/dual core) and/or Cortex-M3
* Integrated SRAM up to 6MB
* Integrated gigabit ethernet switch
* Optional DDR2/3 controller
* I2C, SPI, UART, NAND, QSPI, SDIO, USB, CAN, RTC, LCD
Add basic support for this family, modeled on the existing RZA1.
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
This is taken directly from Linux kernel 6.3
(commit 457391b0380335d5e9a5babdec90ac53928b23b4)
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Commit 2564fce7ee ("sunxi: move Cortex SMPEN setting into start.S")
added SPL_ARMV7_SET_CORTEX_SMPEN to enable setting SMP bit. For
platforms not using SPL boot, add the corresponding non-SPL config,
so that CONFIG_IS_ENABLED(ARMV7_SET_CORTEX_SMPEN) works as expected.
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The original function was only called once, before relocation. The new
one is called again after relocation. This was not the intent of the
original call. Fix this by renaming and updating the calling logic.
With this, chromebook_link64 makes it through SPL.
Fixes: 7fe32b3442 ("event: Convert arch_cpu_init_dm() to use events")
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This avoid an error with enable_sata_clock when
defined(CONFIG_SATA) is changed to CONFIG_IS_ENABLED(SATA).
Signed-off-by: Troy Kisky <troykiskyboundary@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The OTG port is identified by inspecting the "dr_mode" property which is
expected to be "otg" for this port. But it will work just as well as a
device controller when dr_mode is set to "peripheral", which may be
required if the mode detection pin is not set up correctly and the
device controller needs to be programmed to override this.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Instead of duplicating the string values here, use usb_get_dr_mode() to
handle the property lookup and converting the values to an enum.
This is implemented with a switch in preparation for the next patch
which adds extra handling for peripheral mode.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Linux commit 246450344dad arm64: dts: rockchip: rk3399: Radxa ROCK 4C+
Add support for Radxa ROCK 4C+ SBC.
Key differences of 4C+ compared to previous ROCK Pi 4.
- Rockchip RK3399-T SoC
- DP from 4C replaced with micro HDMI 2K@60fps
- 4-lane MIPI DSI with 1920*1080
- RK817 Audio codec
Also, an official naming convention from Radxa mention to remove
Pi from board name, so this 4C+ is named as Radxa ROCK 4C+ not
Radxa ROCK Pi 4C+.
Signed-off-by: Stephen Chen <stephen@radxa.com>
Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
sync dts{,i} files for Radxa ROCK Pi 4 series with Linux 6.3.
because rk3399-rock-pi-4a.dts is enough for ROCK Pi 4A/B/A+/B+ and ROCK
4SE, delete dts{,i} for ROCK Pi 4B.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Anbernic RGxx3 is a "pseudo-device" that encompasses the following
devices:
- Anbernic RG353M
- Anbernic RG353P
- Anbernic RG353V
- Anbernic RG353VS
- Anbernic RG503
The rk3566-anbernic-rgxx3.dtsi is synced with upstream Linux, but
rk3566-anbernic-rgxx3.dts is a U-Boot specific devicetree that
is used for all RGxx3 devices.
Via the board.c file, the bootloader automatically sets the correct
fdtfile, board, and board_name environment variables so that the
correct devicetree can be passed to Linux. It is also possible to
simply hard-code a single devicetree in the boot.scr file and use
that to load Linux as well.
The common specifications for each device are:
- Rockchip RK3566 SoC
- 2 external SDMMC slots
- 1 USB-C host port, 1 USB-C peripheral port
- 1 mini-HDMI output
- MIPI-DSI based display panel
- ADC controlled joysticks with a GPIO mux
- GPIO buttons
- A PWM controlled vibrator
- An ADC controlled button
All of the common features are defined in the devicetree synced from
upstream Linux.
TODO: DSI panel auto-detection for the RG353 devices (requires porting
of DSI controller driver and DSI-DPHY driver to send DSI commands to
the panel).
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The fdt_addr_t and phys_addr_t size have been decoupled.
A 32bit CPU can expect 64-bit data from the device tree parser,
so fix ofnode_get_addr_size function with fdt_addr_t input to
be able to handle both sizes for stm32mp SoC in spl.c file.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The fdt_addr_t and phys_addr_t size have been decoupled. A 32bit CPU
can expect 64-bit data from the device tree parser, so fix some
debug strings with fdt_addr_t to be able to handle both sizes.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The fdt_addr_t and phys_addr_t size have been decoupled. A 32bit CPU
can expect 64-bit data from the device tree parser, so use
dev_read_addr_ptr instead of the dev_read_addr function in the
various files in the drivers directory that cast to a pointer.
As we are there also streamline the error response to -EINVAL on return.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The Rockchip SoC rk3288 has 2 types of device trees floating around.
A 64bit reg size when synced from Linux and a 32bit for U-boot.
A pre-probe function in the syscon class driver assumes only 32bit.
For other odd reg structures the regmap must be defined in the individual
syscon driver. Store rk3288 platdata in a regmap before pre-probe
during bind.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Somehow, I managed to typo our company name in the U-Boot
and Linux kernel submissions.
Fix this and update the copyright year at the same time.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> # on LS1088A-RDB
This synchronises the Linux device tree with U-Boot
(cp linux/..../fsl-ls1088a-ten64.dts uboot/..../fsl-ls1088a-ten64.dts),
as of Linux v6.2-rc5.
Missing from the U-Boot copy previously was the
Ethernet PCS definitions (required for linking with PHY in
Linux but not used by U-Boot) and various upstream
fixes and formatting changes.
The board microcontroller (which doesn't have a Linux driver)
has been moved to the -u-boot.dtsi, as well as the
spi0 quadspi alias (used by U-boot 'sf' but not valid for Linux).
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> # on LS1088A-RDB
Our [U-Boot] copy of fsl-ls1088a.dtsi had all the hardware under
the top level, until the DM_SERIAL implementation recently.
In this commit, remove any remaining devices (that were in U-Boot,
but not touched by previous patches in this series) to be under /soc,
updating to their upstream (Linux) bindings.
The bindings have been copied closest to their relative positions
in the Linux version, so the eventual result is that the U-Boot
and Linux fsl-ls1088a.dtsi will be identical.
The next commit will add the hardware bindings that were not
in U-Boot.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> # on LS1088A-RDB
This moves the fsl-mc device tree definition under the /soc
node, as well as adding interrupt and IOMMU definitions that
were not in U-Boot before.
There are slight differences between the two bindings
as we add a "simple-mfd" compatible to function
under U-Boot's driver model.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> # on LS1088A-RDB
Synchronise the MDIO controller definitions with Linux, so
the controllers will be usable when passing U-Boot's
control FDT to Linux.
This also adds the PCS (internal controller) definitions
which are not used by U-Boot.
Caveat: The kernel definition uses "fsl,fman-memac-mdio",
as with other members of the Layerscape family, but
U-Boot uses a different driver for the DPAA2
Family devices (LS1088/LS2088/LX2160). So
we use "fsl,ls-mdio" as the first compatible string
for these devices.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> # on LS1088A-RDB
Synchronise the USB device tree definition with Linux, allowing
the U-Boot control FDT to be used to boot a Linux system with
working USB.
An extra compatible string, "fsl,layerscape-dwc3" is needed
for special handling in U-Boot, so has been added to the
-u-boot.dtsi file. It might be better to add this to the
Linux source bindings.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> # on LS1088A-RDB
U-Boot's definition for the I2C controllers did not contain any
clock information. This resulted in the I2C not functioning when
the U-Boot control FDT was passed to Linux.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> # on LS1088A-RDB
Move the GPIO controller definitions under the "soc" and in
the same relative position as the Linux kernel fsl-ls1088a.dtsi.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> # on LS1088A-RDB
This is required for Linux to boot using the same FDT as
U-Boot (such as passing the control FDT to bootefi).
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> # on LS1088A-RDB
The Linux kernel fsl-ls1088a.dtsi disables (status="disabled")
all PCIe controllers by default, with the bootloader (i.e U-Boot)
enabling the appropriate controllers (specified by the board
reset control word/RCW) by FDT fixup.
However, U-Boot needs these controllers to be enabled
to be usable, which we can add in the u-boot only dtsi.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> # on LS1088A-RDB
This moves the PCIe controller definitions under /soc and adopts
the same bindings (fsl,ls1088a-pcie) as Linux. Previously,
the format was different between the two versions.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> # on LS1088A-RDB
To synchronise the device tree in U-Boot with Linux, the GIC
(Interrupt Controller) and SMMU/IOMMU nodes need to be synchronised
before changing any dependent components like PCIe and DPAA2/fsl-mc.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> # on LS1088A-RDB
The top-level "memory" node does not exist in the Linux
version of the fsl-ls1088a.dtsi file. Move it to the U-Boot
"tweak" file, so we can have an identical copy of
fsl-ls1088a.dtsi between the projects in the end.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> # on LS1088A-RDB
This moves the bootph-all tags that were added in commit a593c1fec5
("arch: arm: dts: fsl-ls1088a.dtsi: tag serial nodes with bootph-all")
into a u-boot only include.
Due to the way the U-Boot device tree "tweak" system is setup[1],
we need to have a per-board <boardname>-u-boot.dtsi, which will
include the "fsl-ls1088a-u-boot.dtsi" tweaks.
By doing so, future updates to fsl-ls1088a.dtsi from upstream
(Linux kernel) can just be copied directly into the U-Boot tree,
without worrying about any extra data local to U-Boot.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
[1] - https://u-boot.readthedocs.io/en/latest/develop/devicetree/control.html#adding-tweaks-for-u-boot
The CONFIG_SYS_SOC, CONFIG_SYS_CPU and CONFIG_SYS_VENDOR
values are the same for the entire Layerscape family,
meaning there is no ability to create a LS1088A only
file here. But we will be adding per-board tweaks
later in any case.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> # on LS1088A-RDB
This a problem I found while updating the U-Boot fsl-ls1088a.dtsi
to match the Linux version.
fdt_fixup_remove_jr did not check whether there was a "crypto"
alias in the device tree before calling more fdt_* functions,
which resulted in a crash.
Fixes: a797f274
("ARMv8/sec_firmware : Update chosen/kaslr-seed with random number")
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> # on LS1088A-RDB
Update the DDR settings to those generated using 0.6 version of
Jacinto 7 DDRSS Register Configuration tool.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Update the DDR settings to those generated using 0.9.1 version of
Jacinto 7 DDRSS Register Configuration tool.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
On K3 HS-SE devices all the firewalls are locked by default
until sysfw comes up. Rom configures some of the firewall for its usage
along with the SRAM for R5 but the PSRAM region is still locked.
The K3 MCU Scratchpad for j721s2 was set to a PSRAM region triggering the
firewall exception before sysfw came up. The exception started happening
after adding multi dtb support that accesses the scratchpad for reading
EEPROM contents.
Old map:
┌─────────────────────────────────────┐ 0x41c00000
│ SPL │
├─────────────────────────────────────┤ 0x41c61f20 (approx)
│ STACK │
├─────────────────────────────────────┤ 0x41c65f20
│ Global data │
│ sizeof(struct global_data) = 0xd8 │
├─────────────────────────────────────┤ gd->malloc_base = 0x41c66000
│ HEAP │
│ CONFIG_SYS_MALLOC_F_LEN = 0x10000 │
├─────────────────────────────────────┤ CONFIG_SPL_BSS_START_ADDR
│ SPL BSS │ (0x41c76000)
│ CONFIG_SPL_BSS_MAX_SIZE = 0xA000 │
├─────────────────────────────────────┤ (0x41c80000)
│ DM DATA │
├─────────────────────────────────────┤ (0x41c84130) (approx)
│ EMPTY │
└─────────────────────────────────────┘ CONFIG_SYS_K3_BOOT_PARAM_TABLE_INDEX
(0x41cffbfc)
New map:
┌─────────────────────────────────────┐ 0x41c00000
│ SPL │
├─────────────────────────────────────┤ 0x41c61f20 (approx)
│ STACK │
├─────────────────────────────────────┤ 0x41c65f20
│ Global data │
│ sizeof(struct global_data) = 0xd8 │
├─────────────────────────────────────┤ gd->malloc_base = 0x41c66000
│ HEAP │
│ CONFIG_SYS_MALLOC_F_LEN = 0x10000 │
├─────────────────────────────────────┤ CONFIG_SPL_BSS_START_ADDR
│ SPL BSS │ (0x41c76000)
│ CONFIG_SPL_BSS_MAX_SIZE = 0xA000 │
├─────────────────────────────────────┤ (0x41c80000)
│ DM DATA │
├─────────────────────────────────────┤ (0x41c84130) (approx)
│ EMPTY │
├─────────────────────────────────────┤ SYS_K3_MCU_SCRATCHPAD_BASE
│ SCRATCHPAD │ (0x41cff9fc)
│ SYS_K3_MCU_SCRATCHPAD_SIZE = 0x200 │
└─────────────────────────────────────┘ CONFIG_SYS_K3_BOOT_PARAM_TABLE_INDEX
(0x41cffbfc)
Reviewed-by: Kamlesh Gurudasani <kamlesh@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Create *-u-boot.dtsi files for each target dtb of the IOT2050 series so
that we can drop the #include deviations from upstream dts[i] files
here.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
This platform is unsupported by TI and was never widely distributed. As
this is untested for a long while and missing some DM conversions,
remove it and related device tree files.
Signed-off-by: Tom Rini <trini@konsulko.com>
Errata doc: https://www.ti.com/lit/pdf/sprz457
Errata ID i2331 CPSW: Device lockup when reading CPSW registers
Details: A device lockup can occur during the second read of any CPSW
subsystem register after any MAIN domain power on reset (POR). A MAIN
domain POR occurs using the hardware MCU_PORz signal, or via software
using CTRLMMR_RST_CTRL.SW_MAIN_POR or CTRLMMR_MCU_RST_CTRL.SW_MAIN_POR.
After these resets, the processor and internal bus structures may get
into a state which is only recoverable with full device reset using
MCU_PORz.
Due to this errata, Ethernet boot should not be used on this device.
Workaround(s): To avoid the lockup, a warm reset should be issued after
a MAIN domain POR and before any access to the CPSW registers. The warm
reset realigns internal clocks and prevents the lockup from happening.
Workaround above errata by calling do_reset() in case of cold boot in
order to trigger warm reset. This needs enabling SYSRESET driver in R5
SPL to enable TI SCI reset driver.
Signed-off-by: Nitin Yadav <n-yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Add board specific devicetree for Bananapi R3 SBC.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Enable Quality of Service (QoS) blocks for Display SubSystem (DSS), by
servicing the DSS - DDR traffic from the Real-Time (RT) queue. This is
done by setting the DSS DMA orderID to 8.
The C7x and VPAC have been overwhelming the DSS's access to the DDR
(when it was accessing via the Non Real-Time (NRT) Queue), primarily
because their functional frequencies, and hence DDR accesses, were
significantly higher than that of DSS. This led the display to flicker
when certain edgeAI models were being run.
With the DSS traffic serviced from the RT queue, the flickering issue
has been found to be mitigated.
The am62a qos files are auto generated from the k3 resource partitioning
tool.
Section-3.1.12, "QoS Programming Guide", in the AM62A TRM[1], provides
more information about the QoS, and section-14.1, "System Interconnect
Registers", provides the register descriptions.
[1] AM62A Tech Ref Manual: https://www.ti.com/lit/pdf/spruj16
Signed-off-by: Aradhya Bhatia <a-bhatia1@ti.com>
J721E and J7200 have same file j721e_init.c which had the firewall
configs for J721E being applied on J7200 causing the warnings. Split the
firewalls for both the boards to remove those warnings.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
K3 devices have some firewalls set up by ROM that we usually remove so
that the development is easy in HS devices.
While removing the firewalls disabling a background region before
disabling the foreground regions keeps the firewall in a state where all
the transactions will be blacklisted until all the regions are disabled.
This causes a race for some other entity trying to access that memory
region before all the firewalls are disabled and causes an exception.
Since the background regions configured by ROM are in such a manner
that they allow all transactions, don't touch the background regions at
all.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Reviewed-by: Kamlesh Gurudasani <kamlesh@ti.com>
Allow non fitImage bootflow on Field Securable (HS-FS) devices in
addition to GP, force fitImage boot only on Security enforced (HS-SE)
devices where signed images are necessary to maintain chain of trust.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Kamlesh Gurudasani <kamlesh@ti.com>
On modern Qualcomm platforms including SDM845 a GENI SE QUP IP
description is supposed to be found in board device tree nodes,
the version of the IP is used by the GENI UART driver to properly
set an oversampling divider value, which impacts UART baudrate.
The change touches dragonboard845c and starqltechn board device
tree source files, a device tree node label to "debug" UART is
renamed to 'uart9' according to the naming found in Linux.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
The name "se" is used in upstream Linux device trees and has been for
ages, long before this U-Boot-ism was introduced. Same goes for the
existing compatible. Get rid of that.
[vzapolskiy: removed a ready change in the driver]
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
This adds a simple Northstar "BRCMNS" board to be used with
the BCM4708x and BCM5301x chips.
The main intention is to use this with the D-Link DIR-890L
and DIR-885L routers for loading the kernel into RAM from
NAND memory using the BCH-1 ECC and using the separately
submitted SEAMA load command, so we are currently not adding
support for things such as networking.
The DTS file is a multiplatform NorthStar board, designed to
be usable with several NorthStar designs by avoiding any
particulars not related to the operation of U-Boot.
If other board need other ECC for example, they need to
create a separate DTS file and augment the code, but I don't
know if any other users will turn up.
Cc: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The original Northstar is an ARM SoC series that comprise
BCM4709x and BCM5301x and uses a dual-core Cortex A9, the
global timer and a few other things.
This series should not be confused with North Star Plus
(NSP) which is partly supported by U-Boot already.
The SoC is well supported by the Linux kernel and OpenWrt
as it is used in many routers.
Since we currently don't need any chip-specific quirks
and can get the system up from just the device tree, a
mach-* directory doesn't even need to be added, just
some small Kconfig fragments.
Cc: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This brings in the main SoC device tree used by the
Broadcom Northstar chipset, i.e. BCM4709x and BCM5301x.
This is taken from the v6.3 Linux kernel.
Cc: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It doesn't seem appropriate for arch/SOC to use a board-level
functionality (CONFIG_OF_BOARD_FIXUP), because this prevents boards
that need to do FDT fixup from using that feature.
Also, this code is completely dead and useless (from comments by
Rasmus Villemoes on the mailing list):
- No in-tree imx8m-based board seems to set CONFIG_OF_BOARD_FIXUP
- The nodes which that function wants to disable don't even exist in
the U-Boot copy of imx8mp.dtsi.
This code was introduced in commit 35bb60787b. It seems to be some
random import of code from downstream NXP U-Boot, with a commit
message that makes no sense in upstream context.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
commit 787f04bb6a ("imx: add USB2_BOOT type") broke get_boot_device()
for IMX8 which affects booting from SDP due to boot_instance being
non-zero.
Fix this by only using boot_instance for imx8ulp and imx9.
Fixes: 787f04bb6a ("imx: add USB2_BOOT type")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Add debug messages to print the real pixel clock rate, which may not be
the requested one.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Add the get_lcd_clk() function to get the LCD pixel clock rate.
The patch has been tested on imx6ul platform.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
During some tests to check the pixel clock rate in the transition from
U-Boot to the Linux kernel, I noticed that with the same configuration
of the registers the debug messages reported different rates.
The same Linux kernel calculations are now used to get the PLL video
rate.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Avoid a buffer overflow if assigned-clock-rates has less than two elements.
Fixes: 98bcdf1635 ("imx8mn: Add low drive mode support for DDR4/LPDDR4 EVK")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The MNT Reform 2 is a modular DIY laptop. In its initial version it
is based on the BoundaryDevices i.MX8MQ SoM. Some parts have been
lifted from BoundaryDevices official U-Boot downstream project.
Signed-off-by: Patrick Wildt <patrick@blueri.se>
Tested-by: Vagrant Cascadian <vagrant@debian.org>
Tested-by: Vagrant Cascadian <vagrant@debian.org>
Signed-off-by: Stefano Babic <sbabic@denx.de>
Now that this functionality is modeled using the device tree and
regulator uclass, the named GPIO is not referenced anywhere. Remove it.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
On sunxi boards, SPL looks for U-Boot at a 32 KiB offset, unless SPL is
larger than 32 KiB, in which case U-Boot immediately follows SPL. See
the logic in spl_mmc_get_uboot_raw_sector() and spl_spi_load_image().
In two cases, the existing binman description mismatches the SPL code.
For 64-bit boards, binman would place U-Boot immediately following SPL,
even if SPL is smaller than 32 KiB. This can happen when SPL MMC support
is disabled (i.e. when booting from SPI flash).
In contrast, for 32-bit boards, binman would place U-Boot at 32 KiB,
even if SPL is larger than that. This happens because the 'offset'
property does not consider the size of previous entries.
Fix both issues by setting a minimum size for the SPL entry, which
exactly matches the logic in the SPL code. Unfortunately, this size must
be provided as a magic number, since none of the relevant config symbols
(SPL_PAD_TO, SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR, and SYS_SPI_U_BOOT_OFFS)
are guaranteed to be defined in all cases.
Fixes: cfa3db602c ("sunxi: Convert 64-bit boards to use binman")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Since commit de39dc7162 ("arm: armv7-a: Compile and tune for armv7-a
instead of armv5") is used -march=armv7-a option for Omap3 platforms.
With directive ".arch_extension sec" it is possible for -march=armv7-a to
directly use ARM SMC instruction.
So enable ".arch_extension sec" in Omap3 lowlevel_init.S and replace hand
assembled ".word 0xe1600071" by "SMC #1".
Since commit 51d0638650 ("arm: omap-common: add secure smc entry") same
pattern is already used in arch/arm/cpu/armv7/omap-common/lowlevel_init.S.
Signed-off-by: Pali Rohár <pali@kernel.org>
XEN config can be enabled by other platforms (even it doesn't need to make
sense) that's why fix dependencies. XEN (xenbus.c) requires sscanf (also
pvblock needs it). And PVBLOCK is inside drivers/xen folder which requires
XEN to be enabled.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Toolchains which do not directly support using "isb" and "dsb" directly
are no longer functionally supported in U-Boot. Furthermore, clang has
for a long time warned about using the alternate form that we were.
Update the code.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When building for ARM64, we need to pass -ffixed-x18 and otherwise pass
-ffixed-r9. Rather than having this logic in two places, we can do this
once in arch/arm/config.mk. Further, while gcc will ignore being passed
both -ffixed-r9 and -ffixed-x18 and simply use -ffixed-x18, clang will
note that -ffixed-r9 is not used. Remove this duplication to also remove
the warning.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Today, only gcc has __builtin_aarch64_crc32b (clang-16 does not, for
example). Make this option depend on CC_IS_GCC.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Default synchronous exceptions handler prints only esr and register
dump. Sometimes it requiers to see an address which caused exceptions
to understand what's going on
ARM ARM in section D13.2.41 states that FAR_EL2 will contain meanfull
value in case of ESR.EC holds 0x20, 0x21, 0x24, 0x25, 0x22, 0x34 or
0x35. Same applies for EL1.
This patch adds function whivh determine current EL, gets correct FAR
register and prints it on panic.
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Some firewalls enabled by ROM are still left on. So some
address space is inaccessible to the bootloader. For example,
in OSPI boot mode we get an exception and the system hangs.
Therefore, disable all the firewalls left on by the ROM.
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Reviewed-by: Andrew Davis <afd@ti.com>
Reviewed-by: Manorit Chawdhry <m-chawdhry@ti.com>
u-boot could be run at EL1/EL2/EL3. so we set it as same as EL1 does.
otherwise it will hang when enable mmu, that is what we encounter
in our SOC.
Signed-off-by: meitao <meitaogao@asrmicro.com>
[ Paul: pick from the Android tree. Rebase to the upstream ]
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Tom Rini <trini@konsulko.com>
Link: 3bf38943ae
In order to make invalidation by VA more efficient, set the largest
block mapping to 2MB, mapping it onto level-2. This has no material
impact on u-boot's runtime performance, and allows a huge speedup
when cleaning the cache.
Signed-off-by: Marc Zyngier <maz@kernel.org>
[ Paul: pick from the Android tree. Rebase to the upstream ]
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Tom Rini <trini@konsulko.com>
Link: 417a73581a
Some recent arm64 cores have a facility that allows the page
table walker to track the dirty state of a page. This makes it
really efficient to perform CMOs by VA as we only need to look
at dirty pages.
Signed-off-by: Marc Zyngier <maz@kernel.org>
[ Paul: pick from the Android tree. Rebase to the upstream ]
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Tom Rini <trini@konsulko.com>
Link: 3c433724e6
Makes it possible to use e.g mcu_spi0 for custom board detection.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
For setting up the master firewalls present in the K3 SoCs, the arm64
clusters need to be powered on.
Re-locates the code for atf/optee authentication.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
This matches AM64 and J721e and removes the need to forward
declare k3_spl_init(), k3_mem_init(), and check_rom_loaded_sysfw()
in sys_proto.h.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
These probably should be in some system wide header given their use.
Until then move them out of K3 sys_proto.h so we can finish cleaning
that header out.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
This matches how it was done for pre-K3 TI platforms and it allows
us to move the forward declaration out of sys_proto.h.
It also removes the need for K3_BOARD_DETECT as one is free to simply
override the weak function in their board files as needed.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
This header is only used locally by K3 init files, no need to have it
up with the global mach includes. Move into local includes.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
This function is the same for each device when it needs to shutdown
the R5 core. Move this to the common section and move the remaining
device specific ID list to the device hardware include.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
This belongs in the J721e specific file as it is the only place
this is used. Any board level users should use the SOC driver.
While here, move the J721e and J7200 SoC IDs out of sys_proto.h
and into hardware.h. Use a macro borrowed from Rockchip and add
the rest of the SoC IDs for completeness and later use.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
The MSMC fixup is something we do based on SoC, not based on the board.
So this fixup does not belong in the board files. Move this to the
mach-k3 common file so that it does not have to be done in each board
that uses these SoCs.
We use ft_system_setup() here instead of ft_board_setup() since it is no
longer board level. Enable OF_SYSTEM_SETUP in the configurations that use
this to keep functionality the same.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
This reverts commit 5717294230. This
does not exist in upstream kernel.org and breaks boot on DRA7-EVMs.
Drop the same.
Signed-off-by: Andrew Davis <afd@ti.com>
This is a collection of all the whitespace, renames, comment, and other
changes that should not change the DT functionality from Linux v6.3-rc6.
Signed-off-by: Andrew Davis <afd@ti.com>
This is a collection of all the whitespace, renames, comment, and other
changes that should not change the DT functionality from Linux v6.3-rc6.
Signed-off-by: Andrew Davis <afd@ti.com>
This is a collection of all the whitespace, renames, comment, and other
changes that should not change the DT functionality from Linux v6.3-rc6.
Signed-off-by: Andrew Davis <afd@ti.com>
This is a collection of all the whitespace, renames, comment, and other
changes that should not change the DT functionality from Linux v6.3-rc6.
Signed-off-by: Andrew Davis <afd@ti.com>
This is a collection of all the whitespace, renames, comment, and other
changes that should not change the DT functionality from Linux v6.3-rc6.
Signed-off-by: Andrew Davis <afd@ti.com>
Several DTS files have been updated in the Linux kernel with a new
PADCONF macro replacing the IOPAD version. Sync for the same here.
Signed-off-by: Andrew Davis <afd@ti.com>
- Add rk3588 evb support;
- Update pinctrl for rk3568 and rk3588;
- Update rk3288 dts;
- Update mmc support for rk3568 and rk3588;
- Add rng support for rk3588;
- Add DSI support for rk3568;
- Some other misc fixes in dts, config, driver;
_ Add usb_pgood_delay for ST boards
_ increase malloc size for pre-reloc for stm32mp15
_ Set CONFIG_USB_HUB_DEBOUNCE_TIMEOUT=2s for stm32mp15
dts:
_ Add QSPI support on STM32MP13x SoC family
_ Add FMC support on STM32MP13x SoC family
drivers/machine:
_ pinctrl_stm32: Add slew rate support for stm32_pinctrl_get_pin_muxing()
_ spi: stm32_qspi: Remove useless struct stm32_qspi_flash
_ rawnand: stm32_fmc2: remove unsupported EDO mode
_ stm32mp: fix various array bounds checks
-----BEGIN PGP SIGNATURE-----
iQJQBAABCgA6FiEEXyrViUccKBz9c35Jysd4L3sz/6YFAmQ/s+kcHHBhdHJpY2Uu
Y2hvdGFyZEBmb3NzLnN0LmNvbQAKCRDKx3gvezP/pkQHEACnlVjvcMLuT+Fx9fA7
sUfIoDnDQjRugyoEMts0tiAVabPps3rk2fVwuEG6LMRrF5qCTmexjB9HJ0zqIVZj
FxOdP6fLL1629rJpRHQM1tGGmrzktxe/DRGH0VuVKhdH4MLtOWq/yC1XPfmeYh8/
Lt+5uLIMIoBK0sZzNToDctN/KWPA6/UDrFZ7YmnIntL1F39dyiQ+jwvopZZVZ/+v
uP/rwMDDCS7J0yCPa3WocSgOnhN3cE1amgFO7jJP43MBOntWsWmb4TWY+YVoxz1z
PkZPRgQ2YHrFF3vtjL9rCiZSvelnRvSMaO+SZ7AmxNw6KR0ZC0SuCJY9glI257PA
qHK6H7jzHW+Ti2+1NsY8bb8pG9Ewt0AtKc5nSmtbaCgikzdOfoFNOSBIKIZPhXp4
7mxnRbPibK6a6TKIPFL82Ohxnt1hvr+ZD3V2yRdvx0ifMNB1J3F8Rpz4g5i1sPMQ
PqKLAQB6cev8pfw+ItL0VDLhX8zAlCXyrXlxHT0osU88HecIt6ERpNpZZH9Gwp0c
HbR8Sa3VYlG5EyMERmpsVZeA7pBGDtr3aKRRaqsTUrtltRkLOV8SBIXtGLLFiYFW
eEShJO660+Lpb83WenV9A38I8f9qZS9AN+CSAE7EjBDGowAR21VyNcOStz09Yn9a
a84w7wQygGm4mPQWlrOauq57XQ==
=3Txq
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20230419' of https://source.denx.de/u-boot/custodians/u-boot-stm
configs:
_ Add usb_pgood_delay for ST boards
_ increase malloc size for pre-reloc for stm32mp15
_ Set CONFIG_USB_HUB_DEBOUNCE_TIMEOUT=2s for stm32mp15
dts:
_ Add QSPI support on STM32MP13x SoC family
_ Add FMC support on STM32MP13x SoC family
drivers/machine:
_ pinctrl_stm32: Add slew rate support for stm32_pinctrl_get_pin_muxing()
_ spi: stm32_qspi: Remove useless struct stm32_qspi_flash
_ rawnand: stm32_fmc2: remove unsupported EDO mode
_ stm32mp: fix various array bounds checks
Add sdhci node to SPL and u-boot,spl-boot-order. Also add more supported
mmc modes and pinctrl.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add a node for the trng found on RK3588 SoCs.
Changes in V3:
- Added Reviewed-By tag.
Changes in V2:
- None
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Sync the sdmmc node from linux-next, include required nodes in SPL and
imply Kconfig options required for functional sdmmc clk in SPL and
U-Boot proper.
This make it possible for both SPL and U-Boot proper to configure sdmmc
clocks. In SPL, before TF-A is loaded, scru regs is configured, in
U-Boot proper a SCMI message is sent to TF-A.
Fixes: 95c8656b72 ("ARM: dts: rockchip: rk3588s-u-boot: Add sdmmc node")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Booting from sdmmc on RK3588 currently works because of a workaround in
the device tree, clocks are reordered so that the driver use ciu-sample
instead of ciu, and the BootRom initializes sdmmc clocks before SPL is
loaded into DRAM.
The sdmmc clocks are normally controlled by TF-A using SCMI. However,
there is a need to control these clocks in SPL, before TF-A has started.
This adds a rk3588_scru driver to control the sdmmc clocks in SPL before
TF-A has started, using scru regs. It also adds a small glue driver to
bind the scmi clock node to the rk3588_scru driver in SPL.
Fixes: 7a474df740 ("clk: rockchip: Add rk3588 clk support")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add fdtoverlay_addr_r, kernel_comp_addr_r and imply use of
OF_LIBFDT_OVERLAY on RK3568 and RK3588 to support fdtoverlay
and kernel compression.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
The TF-A blobs used to boot RK3568 and RK3588 boards is based on atf
v2.3. Mainline atf v2.3 contains an issue that could lead to a crash
when it fails to parse the fdt blob being passed as the platform param.
An issue that was fixed in atf v2.4.
The vendor TF-A seem to suffer from a similar issue, and this prevents
booting when fdt blob is large enough to trigger this condition.
Fix this by implying SPL_ATF_NO_PLATFORM_PARAM to let u-boot pass a
NULL pointer instead of the fdt blob as the platform param.
This fixes booting Radxa ROCK 3A after recent sync of device tree.
Fixes: 073d911ae6 ("rockchip: rk3568-rock-3a: Sync device tree from linux")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Running U-Boot from a SD-card on ROCK 5 Model B fails to load atf using
DMA and prints debug_uart messages.
<debug_uart>
<debug_uart>
U-Boot SPL 2023.04-rc3 (Mar 12 2023 - 00:30:16 +0000)
Trying to boot from MMC1
## Checking hash(es) for config config-1 ... OK
## Checking hash(es) for Image atf-1 ... sha256 error!
Bad hash value for 'hash' hash node in 'atf-1' image node
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###
Use fifo-mode to disable DMA in SPL, add same-as-spl to boot-order and
remove DEBUG_UART_ANNOUNCE option to fix this.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
misc_read() is documented to return the number of bytes read or a
negative error value. The Rockchip drivers currently do not implement
this correctly and instead return zero on success or a negative error
value.
In preparation for fixing the drivers, fix the condition here to only
error on negative values.
Suggested-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync rk3066/rk3188 DT files from Linux.
This is the state as of linux-next v6.2-rc4.
New nfc node for MK808 rk3066a.
CRU nodes now have a clock property.
To prefend dtoc errors a fixed clock must also be
included for tpl/spl in the rk3xxx-u-boot.dtsi file.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The gpio node names are made generic, but without
gpio bank ID. Add gpio-ranges to rk3188-u-boot.dtsi
for now till a better method is found.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The gpio node names are made generic, but without
gpio bank ID. Add gpio-ranges to rk3066a-u-boot.dtsi
for now till a better method is found.
Disable gpio6 as the driver gives an error code
on return as status.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In order to better compare the Linux rk3288.dtsi
version 6.3 -rc2 with the U-Boot version partial
sync the pwm nodes.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In order to better compare the Linux rk3288.dtsi
version 6.3 -rc2 with the U-Boot version partial
sync the vop/lvds/mipi/hdmi nodes.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # chromebook-jerry
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The rk3288 edp node has a phy node in Linux with a clock
property while current U-Boot driver expects this clock
on position index 1. Move U-Boot-specific DT clock properties
to rk3288-u-boot.dtsi and partially sync the edp node.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # chromebook-jerry
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In order to better compare the Linux rk3288.dtsi
version 6.3 -rc2 with the U-Boot version partial
sync the grf and pmu nodes.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # chromebook-jerry
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In order to better compare the Linux rk3288.dtsi version
with the U-Boot version move the io-domains nodes.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: John Keeping <john@metanate.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # chromebook-jerry
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
ft_board_setup() should be availble for use in board files but using it
in the rk3288 machine file blocks this functionality.
ft_system_setup() is the more appropriate function to use in a machine
definition.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
There is no support to initialize DRAM on RK3588 SoCs using U-Boot TPL
and instead an external TPL binary must be used to generate a bootable
u-boot-rockchip.bin image.
Enable ROCKCHIP_EXTERNAL_TPL by default for RK3588, add build steps for
RK3588 to documentation and clean up CONFIG_BINMAN_FDT options.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Jagan Teki <jagan@edgeble.ai>
rk3588 evb1 v10 is a evalution board from Rockchip, it is a dev board for
rockchip and also a reference board for board vendors.
Hardware:
SoC: RK3588
DRAM: LPDDR4X 8GB
Debug: UART2 via USB
PCIe: 3x4 *1
SATA *2
HDMI out *2
HDMI IN *1
USB2.0 Host *2
USB3.0 Host *1
Type C *1
MIPI DSI panel
dts Sync from Linux v6.2.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Jagan Teki <jagan@edgeble.ai>
In all these cases, the index on the LHS is immediately afterwards
used to access the array appearing in the ARRAY_SIZE() on the RHS - so
if that index is equal to the array size, we'll access
one-past-the-end of the array.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add QSPI support on STM32MP13x SoC family
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Import the dts files from linux-amlogic/for-next (Linux 6.4-rc1) and
add the old PHY reset bindings for dwmac to the u-boot.dtsi until we
support the new bindings in the PHY node. Without this the PHY is not
functional in u-boot or Linux.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230323143142.780306-13-christianshewitt@gmail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Import the device-tree from linux-amlogic/for-next (Linux 6.4-rc1)
to support the Radxa-Zero2 board.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230323143142.780306-10-christianshewitt@gmail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Import the device-tree from linux-amlogic/for-next (Linux 6.4-rc1)
and omit the NPU node from the A311D board variant dts as this is
not supported under U-Boot.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230323143142.780306-7-christianshewitt@gmail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Import the board dts from the linux-amlogic/for-next (6.4-rc1)
branch. This involves spliting the BPI-M5 dts into a dtsi and
then reusing this for the M2-Pro.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230323143142.780306-4-christianshewitt@gmail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Add support for both the BananaPi BPI-CM4 module and the BananaPi
baseboard which is compatible with the RaspberryPi CM4IO baseboard.
The BananaPi BPI-CM4 module follows the CM4 specifications at [1],
but with a single HDMI port and a single DSI output.
The current CM4IO baseboard DT should work fine on the Raspberry CM4
baseboard and other derivatives baseboards, but proper DT should
be written for other baseboards.
[1] https://datasheets.raspberrypi.com/cm4io/cm4io-datasheet.pdf
Link: https://lore.kernel.org/r/20230307-u-boot-cm4-v1-2-43f5a393cd37@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Add a new config option CONFIG_MVEBU_SPL_SATA_BLKSZ for specifying block
size of SATA disk. This information is used during building of SATA
kwbimage and must be correctly set, otherwise BootROM does not load SPL.
For 4K Native disks CONFIG_MVEBU_SPL_SATA_BLKSZ must be set to 4096.
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Martin Rowe <martin.p.rowe@gmail.com>
Find SATA block device by blk_get_devnum_by_uclass_id() function and read
from it the real block size of the SATA disk.
Signed-off-by: Pali Rohár <pali@kernel.org>
Some SoCs of the H616 family use a die variant, that puts some CPU power
and reset control registers at a different address. There are examples
of two instances of the same board, using different die revisions of the
otherwise same H313 SoC. We need to write to a register in that block
*very* early in the SPL boot, to switch the core to AArch64.
Since the devices are otherwise indistinguishable, let the SPL code read
that die variant and use the respective RVBAR address based on that.
That is a bit tricky, since we need to do that in hand-coded AArch32
machine language, shared by all 64-bit SoCs. To avoid build dependencies
in this mess, we always provide two addresses to choose from, and just
give identical values for all other SoCs. This allows the same code to
run on all 64-bit SoCs, and controls this switch behaviour purely from
Kconfig.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
To switch the ARMv8 Allwinner SoCs into the 64-bit AArch64 ISA, we need
to program the 64-bit start code address into an MMIO mapped register
that shadows the architectural RVBAR register.
This address is SoC specific, with just two versions out there so far.
Now a third address emerged, on a *variant* of an existing SoC (H616).
Change the boot0.h start code to make this address a Kconfig
selectable option, to allow easier maintenance.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
It turns out that some H616 and related SoCs (like H313) need TPR2
parameter for proper working. Add it.
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Currently twr2rd, trd2wr and twtp are constants, but according to
vendor driver they are calculated from other values. Do that here too,
in preparation for later introduction of new parameter.
While at it, introduce constant for t_wr_lat, which was incorrectly
calculated from tcl before.
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Part of the code, previously known as "unknown feature", also doesn't
have constant values. They are derived from TPR0 parameter in vendor
DRAM code.
Let's move that code to separate function and introduce TPR0 parameter
here too, to ease adding new boards.
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
These values are highly board specific and thus make sense to add
parameter for them. To ease adding support for new boards, let's make
them same as in vendor DRAM settings.
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Mentioned function result is always true and result isn't checked
anyway. Let's make it void.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Vendor H616 DRAM code always configure part which we call ODT
configuration. Let's reflect that here too.
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Vendor DRAM settings use TPR10 parameter to enable various features.
There are many mores features that just those that are currently
mentioned. Since new will be added later and most are not known, let's
reuse value from vendor DRAM driver as-is. This will also help adding
support for new boards.
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
While ODT values for same memory type are similar, they are not
necessary the same. Let's parameterize them and make parameter same as
in vendor DRAM settings. That way it will be easy to introduce new board
support.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Fix code style for pointer declaration. This is just cosmetic change to
avoid checkpatch errors in later commits.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Vendor DRAM code actually writes to whole CR register and not just sets
bit 31 in mctl_ctrl_init().
Just to be safe, do that here too.
Acked-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This board is configured with CONFIG_USB1_VBUS_PIN="PH24", but no
regulator exists in its device tree. Add the regulator, so USB will
continue to work when the PHY driver switches to using the regulator
uclass instead of a GPIO.
Update the device tree here because it does not exist in Linux.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
- improve tegra DC driver to work with panel ops and implement
native 180 degree panel rotation support
- add T30 support to tegra DC driver
- add DSI driver (based on mainline Linux one with minor
adjustments, only T30 tested)
- add get_display_timing ops to simple panel driver
- extend simple panel driver to use it for MIPI DSI panels
which do not require additional DSI commands for setup
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCZDBwUw4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXL3+AJ9EkQKAWXZtlYdAOVl4/nzJnuTCAQCfY58zkDsw
TnAlwmMGWFl3RF6yGXY=
=uYUp
-----END PGP SIGNATURE-----
Merge tag 'video-20230407' of https://source.denx.de/u-boot/custodians/u-boot-video
- fix building sandbox without SDL
- improve tegra DC driver to work with panel ops and implement
native 180 degree panel rotation support
- add T30 support to tegra DC driver
- add DSI driver (based on mainline Linux one with minor
adjustments, only T30 tested)
- add get_display_timing ops to simple panel driver
- extend simple panel driver to use it for MIPI DSI panels
which do not require additional DSI commands for setup
Adds support for both DSI outputs found on Tegra. Only very
minimal functionality is implemented, so advanced features
like ganged mode won't work. Driver is heavily based on
mainline Tegra DSI and re-uses much of its features.
Only T30 is supported for now but T20 support can be added
if any supported devices will be found.
Driver is wrapped as panel driver since Tegra DC driver supports
only panel drivers calls.
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # ASUS TF600T T30
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # HTC One X T30
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Internal video devices like DSI and HDMI controllers
require sending commands into DC register field.
To make this available, lets create platform data,
which is restricted to pass DC regmap only to
pre-defined devices.
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # ASUS TF T30
Tested-by: Nicolas Chauvet <kwizart@gmail.com> # Paz00
Tested-by: Robert Eckelmann <longnoserob@gmail.com> # ASUS TF101 T20
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # HTC One X T30
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
On popular request make the display driver from T20 work on T30 as
well. Turned out to be quite straight forward. However a few notes
about some things encountered during porting: Of course the T30 device
tree was completely missing host1x as well as PWM support but it turns
out this can simply be copied from T20. The only trouble compiling the
Tegra video driver for T30 had to do with some hard-coded PWM pin
muxing for T20 which is quite ugly anyway. On T30 this gets handled by
a board specific complete pin muxing table. The older Chromium U-Boot
2011.06 which to my knowledge was the only prior attempt at enabling a
display driver for T30 for whatever reason got some clocking stuff
mixed up. Turns out at least for a single display controller T20 and
T30 can be clocked quite similar. Enjoy.
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # ASUS TF T30
Tested-by: Jonas Schwöbel <jonasschwoebel@yahoo.de> # Surface RT T30
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # LG P895 T30
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Add board code for R8A779G0 V4H White Hawk board.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Synchronize configuration symbols which are now switched to Kconfig
Mallocate gd->bd->bi_boot_params, i.e. drop the assignment
Sort headers, use clrbits_le32(), use BIT macros where appropriate
Use CONFIG_SYS_CLK_FREQ for counter frequency instead of custom macro]
Add Kconfig entry and PRR ID to support R8A779G0 V4H SoC.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Update commit message]
Add DTs for R8A779G0 V4H White Hawk CPU and BreakOut boards.
Based on Linux next 20230228 DTs up to
commit 058f4df42121 ("Add linux-next specific files for 20230228")
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Tho Vu <tho.vu.wh@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Sync with Linux next 20230228, update commit message
Rename DTs to match Linux, which has dash between white-hawk]
Add R8A779G0 V4H DT extras for U-Boot.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Update compatible string to match latest upstream]
Add initial DT support for R8A779G0 (R-Car V4H). Based on Linux next
commit 058f4df42121 ("Add linux-next specific files for 20230228")
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Phong Hoang <phong.hoang.wz@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Sync with Linux next 20230228, update commit message]
Add board code for R8A779F0 S4 Spider board.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Synchronize configuration symbols which are now switched to Kconfig
Mallocate gd->bd->bi_boot_params, i.e. drop the assignment
Sort headers, use clrbits_le32(), use BIT macros where appropriate
Use CONFIG_SYS_CLK_FREQ for counter frequency instead of custom macro]
Add Kconfig entry and PRR ID to support R8A779F0 S4 SoC.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Update commit message]
Add DTs for R8A779F0 S4 Spider CPU boards and Breakout boards.
Based on Linux next 20230228 DTs up to
commit 058f4df42121 ("Add linux-next specific files for 20230228")
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Sync with Linux next 20230228, update commit message]
Add R8A779F0 S4 DT extras for U-Boot.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Update compatible string to match latest upstream]
Add initial DT for R8A779F0 S4 SoC. Based on Linux next
commit 058f4df42121 ("Add linux-next specific files for 20230228")
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Sync with Linux next 20230228, update commit message]
This adds R-Car Generation 4 (Gen4) support as Renesas ARM64 SoC.
In this version, reusing R-Car Gen3 lowlevel initialize routine [1]
and R-Car Gen3 memory map tables [2] .
[1] arch/arm/mach-rmobile/lowlevel_init_gen3.S
[2] arch/arm/mach-rmobile/memmap-gen3.c
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: - Enable DTO support by default
- Sort the Kconfig lists
- Select RCAR_64 Kconfig option to pull in all the shared
Kconfig options with Gen3, and use where applicable to
deduplicate entries.
- Fix reference [2] typo in commit message
- Drop config options moved to Kconfig, rename rest to CFG_
accordingly to synchronize with upstream changes. Drop
removed CONFIG_VERY_BIG_RAM.
- Move board size limit to arch/Kconfig
- Move GICR_BASE to headers instead of common config]
The assembly for __gnu_thumb1_case_si was taken from upstream gcc and adapted
as width suffix was removed for the add instruction [1].
Signed-off-by: Francis Laniel <francis.laniel@amarulasolutions.com>
Tested-by: Tony Dinh <mibodhi@gmail.com>
[1] 4f181f9c7e/libgcc/config/arm/lib1funcs.S (L2156)
Acked-by: Pali Rohár <pali@kernel.org>
Acked-by: Tony Dinh <mibodhi@gmail.com>
Tag the serial nodes with bootph-all in order to have these nodes and
the drivers available before relocation.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Sync the serial nodes of the LX2160A based boards with their
representation in Linux. We also imported the clockgen and sysclk nodes
which are dependencies.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Move the serial nodes under the soc node. No changes are made to the
nodes, just their location is changed.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The u-boot dts for these boards do not have an soc node, unlike its
Linux counterpart. This patch just adds the soc node as seen in Linux,
the next patches will move some nodes under it.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Tag the serial nodes with bootph-all in order to have these nodes and
the drivers available before relocation.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Sync the serial nodes of the LS1088A based boards with their
representation in Linux. We also imported the clockgen and sysclk nodes
which are dependencies.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Move the serial nodes under the soc node. No changes are made to the
nodes, just their location is changed.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The u-boot dts for these boards do not have an soc node, unlike its
Linux counterpart. This patch just adds the soc node as seen in Linux,
the next patches will move some nodes under it.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
