Commit graph

4303 commits

Author SHA1 Message Date
Max Krummenacher
8da72960ed verdin-imx8mm: enable sleep_moci output
This powers some peripherals on the carrier board e.g. the USB hub.

Related-to: ELB-3206
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
2021-10-20 15:08:26 +02:00
Marcel Ziswiler
5cfa55930b verdin-imx8mm: switch to use binman to pack images
Use binman to pack images.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
2021-10-20 15:08:26 +02:00
Marcel Ziswiler
088eb75407 arm64: dts: imx8mm-verdin-u-boot.dtsi: alphabetically re-order
Alphabetically re-order nodes and properties.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2021-10-20 15:08:25 +02:00
Marcel Ziswiler
8d060e4a66 ARM: dts: imx8mm-verdin: prepare for dek blob encapsulation
Prepare for DEK blob encapsulation support through "dek_blob" command.
On ARMv8, u-boot runs in non-secure, thus cannot encapsulate a DEK blob
for encrypted boot.
The DEK blob is encapsulated by OP-TEE through a trusted application
call. U-boot sends and receives the DEK and the DEK blob binaries
through OP-TEE dynamic shared memory.

To enable the DEK blob encapsulation, add to the defconfig:
CONFIG_SECURE_BOOT=y
CONFIG_FAT_WRITE=y
CONFIG_CMD_DEKBLOB=y

Taken from NXP's commit 56d2050f40 ("imx8m: Add DEK blob encapsulation
for imx8m").

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
2021-10-20 15:08:25 +02:00
Chris Morgan
193ab22797 rockchip: px30: sync serial flash controller bindings with mainline
The devicetree submitted and approved for the mainline linux kernel is
slightly different than the one present here. This syncs both
devicetrees (for the Rockchip SFC node at least) present on the PX30
and the Odroid Go Advance. Changes include renaming the flash node,
reordering the values in the SFC node for the rk3326-odroid-go2,
changing the name of the cs pinctrl node to cs0, and updating the
u-boot specific tree to utilize the new flash node value.

Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2021-10-15 20:56:55 +08:00
Chris Morgan
8d43e2412a rockchip: board: remove SCLK_GPU from U-Boot DT
Starting with commit 92f1e9a4b3 ("clk: Detect failure to set
defaults") the clk driver for the PX30 would fail to probe for the
Odroid Go Advance. This patch is to remove the clock for the GPU from
the U-Boot specific devicetree, as that clock is not supported by the
U-Boot clk_px30 driver.

Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2021-10-15 20:56:09 +08:00
Tom Rini
776bf6a545 - Disable ATAGS for STM32 MCU and MPU boards
- Disable bi_boot_params for STM32 MCU and MPU boards
 - Update stm32-usbphyc node management
 - Convert CONFIG_STM32_FLASH to Kconfig for STM32 MCU boards
 - Convert some USB config flags to Kconfig for various boards
 - Convert CONFIG_BOOTCOMMAND flag to Kconfig for STM32 F429 board
 - Remove specific CONFIG_STV0991 flags
 - Remove unused CONFIG_USER_LOWLEVEL_INIT flag
 - Add ofdata_to_platdata() callback for stm32_spi driver
 - Update for stm32f7_i2c driver
 - Remove gpio_hog_probe_all() from STM32 MP1 board
 - Fix bind command
 -----BEGIN PGP SIGNATURE-----
 
 iQJQBAABCgA6FiEEXyrViUccKBz9c35Jysd4L3sz/6YFAmFlgsIcHHBhdHJpY2Uu
 Y2hvdGFyZEBmb3NzLnN0LmNvbQAKCRDKx3gvezP/plnND/4q9HSlvddybIPjBHlW
 rXz1ISwj8JZPp7R4MJcB4RiHofYZzjTXx3dDYUif6oQMpCDp64KPfcUDW0kaq8U7
 ZFwJvt59boV1XWlonIXMb3gAkY6gFa5PnYAE/YXEqKvPPvUb7FkT7BWxm4LxCGsj
 mEmboR8u87s6e4ZP03HJsSVa5FnNwJUZU8b+58Vxp10YC0PPf7kpmgCucDhrghvY
 TORlk259KUFoZXz4J4My0VzDdxE05gDqq1m6Xw1CzqcUbGysMvjNEHlxGdYbWD/U
 maamP19DUmKUREmpj3kO/JZvacLJlQP/mdGJ0OWKNbIr/3ha4dYagxDoRodEVo0m
 DYaaVPGvG24G78d5meB2q9wT0aGdTyaqm+XRBQMvMN2LlaGmu9duA1t6yBuyMcFk
 BeA7d0eHMo1ezD9FFZMxwIOAWhJlcYQEAMFhUwkR1B322w0NU4nbl9KRCGuGV2Zp
 ZFQV4BoMvb0NwAdo66xwZ+gSq4Wp1y46VM6x2Mw52v2F4p3teeAqR906TdQVYO8+
 hlYChO9+qK4JO7LPX/5wQ4FIzcq1HnTzTpuOSf28hsemiPMu0OkAQv1J7DohNZix
 wELBA+ZIjGXksmDTPjpXg5CSvVALa/l2G816hp7/XTJ1XRBSz/pzjhp5rwm42zmw
 x7EPnwzpAlQCSqTQ0sgO+fgoRA==
 =S4kl
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-stm32-20211012' of https://source.denx.de/u-boot/custodians/u-boot-stm

- Disable ATAGS for STM32 MCU and MPU boards
- Disable bi_boot_params for STM32 MCU and MPU boards
- Update stm32-usbphyc node management
- Convert CONFIG_STM32_FLASH to Kconfig for STM32 MCU boards
- Convert some USB config flags to Kconfig for various boards
- Convert CONFIG_BOOTCOMMAND flag to Kconfig for STM32 F429 board
- Remove specific CONFIG_STV0991 flags
- Remove unused CONFIG_USER_LOWLEVEL_INIT flag
- Add ofdata_to_platdata() callback for stm32_spi driver
- Update for stm32f7_i2c driver
- Remove gpio_hog_probe_all() from STM32 MP1 board
- Fix bind command

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-10-12 12:01:00 -04:00
Tom Rini
618c77d99a Second set of u-boot-at91 features for the 2022.01 cycle
-----BEGIN PGP SIGNATURE-----
 
 iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmFlfXAcHGV1Z2VuLmhy
 aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyHzuB/4pV2iAeFBjNf6YYsuk
 uvBQm7+j+AQzy0J337bDwulvw8wTKKlaid4qfOpEjW316DI9oXN1bXTlwNsjtQvO
 zTILW7MoBjDRhZHsSkeSfIuD+Sc80juAoLBv+GXskQdZOTQUbWdmi2o60gdY5Ba4
 WN0i4zOGVqd7xoDuDgM3XC1M2RnKerxDeVt20Ji+5dFfmes11m7br6sWj2j/45f+
 q3G1ufHl+ea+8oRLZGjn2ddKCb1wLLOrNZA+74dsZ5SN0LCN0vFsE3+JAk4RZ2A5
 omiHVApjE+J3vAjwiVY7apjcIdVEeyb5AioiXSBAEZiq1l1UI7eKDQT75bDkaKSs
 4wBV
 =78ME
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-at91-2022.01-b' of https://source.denx.de/u-boot/custodians/u-boot-at91

Second set of u-boot-at91 features for the 2022.01 cycle:

This small feature set adds the support for PWM driver for the sama5d2
SoC. It also adds a node in the DT for this SoC.
2021-10-12 11:49:15 -04:00
Tom Rini
2aab77f726 Merge https://source.denx.de/u-boot/custodians/u-boot-sunxi
The bulk of it is Samuel's DM_I2C rework, which removes the nasty I2C
deprecation warnings for most 32-bit boards. It also includes some
smaller refactorings that pave the way for more changes, mostly driven
by needing to support the Allwinner RISC-V SoC later on.

Board wise we gain support for the FriendlyARM NanoPi R1S H5 router
board and official Pinetab support.

Build-tested for all 160 sunxi boards, and boot tested on a A64, A20,
H3, H6, and H616 board. USB, SD card, eMMC, and Ethernet all work there
(where applicable).
2021-10-12 11:45:00 -04:00
Dan Sneddon
1f83bda788 ARM: dts: sama5d2: Add pwm0 definition
Add node for the PWM0 on the SAMA5D2 SoC.

Signed-off-by: Dan Sneddon <dan.sneddon@microchip.com>
2021-10-12 15:18:39 +03:00
Jan Kiszka
08ad739f38 arm: dts: Update IOT2050 device tree files
This fixes the usage of the USB 3.0-capable port under U-Boot as USB
2.0-only port.

Original patch by Chao Zeng.

Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
2021-10-11 15:02:50 -04:00
Jan Kiszka
ce543d0d4e board: siemens: iot2050: Adjust to changes in DT and configuration
Account for the changes done between merge proposal and the final merge.

Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2021-10-11 15:02:50 -04:00
Dario Binacchi
15a0411787 ARM: dts: am43xx-clocks: add spread spectrum support
Registers for adjusting the spread spectrum clocking (SSC) have been
added. As reported by the TI spruhl7x RM, SSC is supported only for LCD
and MPU PLLs, but the PRCM_CM_SSC_DELTAMSTEP_DPLL_XXX and
PRCM_CM_SSC_MODFREQDIV_DPLL_XXX registers, as well as the enable field
in the PRCM_CM_CLKMODE_DPLL_XXX registers are mapped for all PLLs (CORE,
MPU, DDR, PER, DISP, EXTDEV).

Link: https://lore.kernel.org/r/20210606202253.31649-5-dariobin@libero.it

Signed-off-by: Dario Binacchi <dariobin@libero.it>
2021-10-11 14:27:32 -04:00
Dario Binacchi
bf4a54fa78 ARM: dts: am33xx-clocks: add spread spectrum support
Registers for adjusting the spread spectrum clocking (SSC) have been
added. As reported by the TI spruh73x RM, SSC is supported only for LCD
and MPU PLLs, but the CM_SSC_DELTAMSTEP_DPLL_XXX and
CM_SSC_MODFREQDIV_DPLL_XXX registers, as well as the enable field in the
CM_CLKMODE_DPLL_XXX registers are mapped for all PLLs (CORE, MPU, DDR,
PER, DISP).

Link: https://lore.kernel.org/r/20210606202253.31649-4-dariobin@libero.it
Signed-off-by: Dario Binacchi <dariobin@libero.it>
2021-10-11 14:27:32 -04:00
Chukun Pan
e7510d24ca sunxi: Add support for FriendlyARM NanoPi R1S H5
This adds support for the NanoPi R1S H5 board.

Allwinner H5 SoC
512MB DDR3 RAM
10/100/1000M Ethernet x 2
RTL8189ETV WiFi 802.11b/g/n
USB 2.0 host port (A)
MicroSD Slot
Reset button
Serial Debug Port
WAN - LAN - SYS LED

The dts file is taken from Linux 5.14 tag.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-10-11 10:46:44 +01:00
Patrice Chotard
2aaac1787a arm: dts: stm32: Add i2c-analog-filter property in I2C nodes for stm32h743
Add i2c-analog-filter property in I2C nodes to enable analog
filter feature.

Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
2021-10-08 08:42:40 +02:00
Patrice Chotard
5d59bd553b arm: dts: stm32: Add i2c-analog-filter property in I2C nodes for stm32f746
Add i2c-analog-filter property in I2C nodes to enable analog
filter feature.

Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
2021-10-08 08:42:40 +02:00
Robert Marko
cfb7102d8d arm: mvebu: dts: m801: correct CP1 pinctrl
Current CP1 pinctrl that is set on the Puzzle M801 is incorrect.
CP1 pins are only used for the SMI bus and the MSS I2C, all other
pins are just GPIO-s.

Due to this being set completely wrong, the pinctrl was actually
ended up being hardcoded in the board_early_init_f() step so that
SMI would work.

That is obviously not the right thing to do, so convert the register
hex values that were being written to individual pin modes and set it
in the DTS.
Add the SMI pins to the CP1 MDIO node as otherwise CP1 pinctrl does
not get probed without an consumer.

Fixes: 2ae2b8a2 ("arm: mvebu: Initial iEi Puzzle-M801 support")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
2021-10-08 08:37:55 +02:00
Pali Rohár
646a152247 arm: a37xx: pci: Increase PCIe IO size from 64 KiB to 1 MiB
Commit 079b35a261 ("arm: a37xx: pci: Increase PCIe MEM size from 16 MiB
to 127 MiB") increased size of PCIe MEM to 127 MiB, which is the maximal
possible size for allocated 128 MiB PCIe window. PCIe IO size in that
commit was unchanged.

Armada 3720 PCIe controller supports 32-bit IO space mapping so it is
possible to assign more than 64 KiB if address space for IO.

Currently controller has assigned 127 MiB + 64 KiB memory and therefore
there is 960 KiB of unused memory. So assign it to IO space by increasing
IO window from 64 KiB to 1 MiB.

Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: 079b35a261 ("arm: a37xx: pci: Increase PCIe MEM size from 16 MiB to 127 MiB")
Reviewed-by: Stefan Roese <sr@denx.de>
2021-10-08 08:33:52 +02:00
Tim Harvey
a31de24473 arm64: dts: imx8mm-venice-gw7902: use imx8mm-venice-u-boot.dtsi
Use the common imx8mm-venice-u-boot.dtsi (dtb for the
'DEFAULT_DEVICE_TREE) so that it inherits things like binman.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-10-07 17:45:01 +02:00
Tim Harvey
129c0c57b5 arm64: dts: imx8mm-venice-gw7901: use imx8mm-venice-u-boot.dtsi
Use the common imx8mm-venice-u-boot.dtsi (dtb for the
'DEFAULT_DEVICE_TREE) so that it inherits things like binman.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-10-07 17:45:00 +02:00
Tim Harvey
75c337cf2b arm64: dts: imx8mm-venice-gw700x: use imx8mm-venice-u-boot.dtsi
Use the common imx8mm-venice-u-boot.dtsi (dtb for the
'DEFAULT_DEVICE_TREE) so that it inherits things like binman.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-10-07 17:45:00 +02:00
Frieder Schrempf
9cab87f184 imx: imx8mm: Add support for Kontron Electronics SL/BL i.MX8M-Mini boards (N801x)
The Kontron SoM-Line i.MX8MM (N801x) by Kontron Electronics GmbH is a SoM
module with an i.MX8M-Mini SoC, 1/2/4 GB LPDDR4 RAM, SPI NOR, eMMC and PMIC.

The matching evaluation boards (Board-Line) have 2 Ethernets, USB 2.0, HDMI/LVDS,
SD card, CAN, RS485 and much more.

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Tested-by: Heiko Thiery <heiko.thiery@gmail.com>
2021-10-07 17:31:58 +02:00
Tim Harvey
073b105e79 imx: ventana: fix USB hub reset
Remove board_ehci_hcd_init function that is not used with DM_USB
and replace its functionality with device-tree configuraton that treats
USB HUB RST# as a gpio enable for the usbh1 vbus regulator.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-10-07 16:53:50 +02:00
Frieder Schrempf
e6f48aad15 imx: imx6ul: Add support for Kontron Electronics SL/BL i.MX6UL/ULL boards (N63xx/N64xx)
This adds support for i.MX6UL/ULL-based evaluation kits with SoMs by
Kontron Electronics GmbH.

Currently there are the following SoM flavors (SoM-Line):
  * N6310: SOM with i.MX6UL-2, 256MB RAM, 256MB SPI NAND
  * N6311: SOM with i.MX6UL-2, 512MB RAM, 512MB SPI NAND
  * N6411: SOM with i.MX6ULL, 512MB RAM, 512MB SPI NAND

And the according evaluation boards (Board-Line):
  * N6310-S: Baseboard with SOM N6310, eMMC, display (optional), ...
  * N6311-S: Baseboard with SOM N6311, eMMC, display (optional), ...
  * N6411-S: Baseboard with SOM N6411, eMMC, display (optional), ...

Currently U-Boot describes i.MX6UL and i.MX6ULL through separate config
options at compile-time. Though the differences are so minor, that for
the scope of these SoMs we just use a single defconfig that is compatible
with both SoCs.

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2021-10-07 16:53:50 +02:00
Oleksandr Suvorov
cdb18048f9 ARM: dts: imx: use generic name bus
Synchronize the u-boot and kernel imx device trees, using tuned
script from commit c0157bdcafa1 ("ARM: dts: imx: use generic name bus")

Per devicetree specification, generic names are recommended to be
used, such as bus.

i.MX AIPS is an AHB - IP bridge bus, so we could use bus as node
name.

Script:
sed -i "s/\<aips@/bus@/" arch/arm/dts/imx*.dtsi
sed -i "s/\<aips@/bus@/" arch/arm/dts/vf*.dtsi
sed -i "s/\<aips-bus@/bus@/" arch/arm/dts/imx*.dtsi
sed -i "s/\<aips-bus@/bus@/" arch/arm/dts/vf*.dtsi

Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
2021-10-07 16:53:50 +02:00
Ricardo Salveti
5089d2fc8e ARM: dts: imx6-apalis: enable watchdog
Add u-boot.dtsi specific to imx6-apalis with a watchdog enabled.

If OP-TEE is loaded by SPL, it may use a watchdog to handle fails of
u-boot running. Enable the watchdog in SPL to use it by OP-TEE.

Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Reviewed-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
2021-10-07 16:53:50 +02:00
Marek Vasut
af2d3c91d8 ARM: dts: imx8mm-verdin: Set PHY mode to RGMII-ID
Since c6df0e2ffd ("net: phy: micrel: add support for DLL setup on ksz9131")
the Micrel PHY driver correctly configures the delay register. The Verdin PHY
is RGMII-ID, so reflect that in DT, otherwise the ethernet no longer works.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Max Krummenacher <max.krummenacher@toradex.com>
Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2021-10-07 16:53:50 +02:00
Teresa Remmet
42cef89e86 arm: dts: imx8mp: Generate single bootable binary
binman conversion made flashing flash.bin
and u-boot.itb necessary. Update binman config
to create a single flash.bin image again.

This updates imx8mp_evk and phyCORE-i.MX8MP as they share the
same binman config.

Updated also imx8mp_evk documentation.

Tested on phyCORE-i.MX8MP.

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
2021-10-07 16:53:50 +02:00
Fabio Estevam
53a24dee86 imx8mm-cl-iot-gate: Split the defconfigs
Currently imx8mm-cl-iot-gate_defconfig fails to produce a working boot
binary due to the lack of fip.bin:

"  BINMAN  all
Image 'main-section' is missing external blobs and is non-functional: blob-ext

Some images are invalid"

To make the build process more consistent with the other i.MX8M targets,
split the defconfig in two:

- imx8mm-cl-iot-gate_defconfig: standard defconfig that only
requires ATF / DDR firmware.

- imx8mm-cl-iot-gate-optee_defconfig: "more advanced" defconfig that
requires ATF / Optee / mbedtls / DDR firmware.

Signed-off-by: Fabio Estevam <festevam@denx.de>
Tested-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
2021-10-07 16:53:50 +02:00
Tim Harvey
0cf5622998 arm: dts: imx8mm-venice*: remove thermal zone overrides
Remove the unnecessary thermal zone overrides.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-10-07 16:53:50 +02:00
Tim Harvey
cd7f37666a arm: dts: imx8mm-venice-gw700x: fix mp5416 pmic config
Fix various MP5416 PMIC configurations:
 - Update regulator names per dt-bindings
 - ensure values fit among valid register values
 - add required regulator-max-microamp property
 - add regulator-always-on prop

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-10-07 16:53:50 +02:00
Andrej Rosano
aaac39218d imx53: usbarmory: Add card detect configuration
After the enforcement of DM_MMC the microSD card is not detected. Fix by
correctly configuring the card detect in the devicetree.

Signed-off-by: Andrej Rosano <andrej.rosano@f-secure.com>
2021-10-07 16:53:50 +02:00
Christian Hewitt
b1463cbb54 ARM: dts: add support for Radxa Zero
Import the initial dts queued for Linux 5.16.y

Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2021-10-07 13:45:35 +02:00
Christian Hewitt
8ee224bfe4 ARM: dts: sort Amlogic Makefile section
Alpha sort the Amlogic dtb list (same as the kernel).

Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2021-10-07 13:45:35 +02:00
Vyacheslav Bocharov
de19baef68 ARM: amlogic: add JetHub D1/H1 device support
Add support for new home automation devices.

JetHome Jethub D1 (http://jethome.ru/jethub-d1) is a home automation controller with the following features:
- DIN Rail Mounting case
- Amlogic A113X (ARM Cortex-A53) quad-core up to 1.5GHz
- no video out
- 512Mb/1GB DDR3
- 8/16GB eMMC flash
- 1 x USB 2.0
- 1 x 10/100Mbps ethernet
- WiFi / Bluetooth AMPAK AP6255 (Broadcom BCM43455) IEEE 802.11a/b/g/n/ac, Bluetooth 4.2.
- TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power and Zigbee 3.0 support.
- 2 x gpio LEDS
- GPIO user Button
- 1 x 1-Wire
- 2 x RS-485
- 4 x dry contact digital GPIO inputs
- 3 x relay GPIO outputs
- DC source with a voltage of 9 to 56 V / Passive POE

JetHome Jethub H1 (http://jethome.ru/jethub-h1) is a home automation controller with the following features:
- Square plastic case
- Amlogic S905W (ARM Cortex-A53) quad-core up to 1.5GHz
- no video out
- 1GB DDR3
- 8/16GB eMMC flash
- 2 x USB 2.0
- 1 x 10/100Mbps ethernet
- WiFi / Bluetooth RTL8822CS IEEE 802.11a/b/g/n/ac, Bluetooth 5.0.
- TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power and Zigbee 3.0 support.
- MicroSD 2.x/3.x/4.x DS/HS cards.
- 1 x gpio LED
- ADC user Button
- DC source 5V microUSB with serial console

Patches from:
- JetHub H1
  https://lore.kernel.org/r/20210915085715.1134940-4-adeep@lexina.in
  https://git.kernel.org/amlogic/c/abfaae24ecf3e7f00508b60fa05e2b6789b8f607
- JetHub D1
  https://lore.kernel.org/r/20210915085715.1134940-5-adeep@lexina.in
  https://git.kernel.org/amlogic/c/8e279fb2903990cc6296ec56b3b80b2f854b6c79

Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
[narmstrong: removed unused variable value]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2021-10-07 13:45:35 +02:00
Neil Armstrong
fe8b4c1080 ARM: amlogic: add Banana Pi M5
Banana Pi BPI-M5 is a credit card format SBC with the following features:
- Amlogic S905X3 quad core Cortex-A55
- Mali-G31 GPU
- 4GB LPDDR4
- 16GB eMMC flash
- 4 USB 3.0
- 1 GbE ethernet
- HDMI output
- 2x LEDS
- SDCard
- 2.5mm Jack with Stereo Audio + CVBS
- Infrared Received
- ADC Button
- GPIO Button
- 40 pins header + 3pins debug header

[narmstrong: add missing CONFIG_SYS_LOAD_ADDR from defconfig]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2021-10-07 13:45:35 +02:00
Neil Armstrong
2c9269b14b ARM: meson: add Beelink GS-King X board
The Beelink GS-King X is a variant of the GS King boards but with an internal
USB to SATA bridge and advanced audio features.

[narmstrong: add missing CONFIG_SYS_LOAD_ADDR from defconfig]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2021-10-07 13:45:32 +02:00
Neil Armstrong
a4b553e31b ARM: amlogic: add support for Odroid-HC4 device
The Odroid-HC4 is a variant of the Odroid-C4 board but with a PCIe-SATA bridge
instead of the USB3 ports.

[narmstrong: add missing CONFIG_SYS_LOAD_ADDR from defconfig]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2021-10-07 13:45:28 +02:00
Neil Armstrong
3da675a93b ARM: meson-axg: remove local USB nodes
Drop the local USB nodes after Linux 5.14 sync.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2021-10-07 10:14:50 +02:00
Neil Armstrong
535dcb55a5 ARM: meson: keep HW order for MMC devices
Since Linux commmit [1], the order is fixed with aliases, in order to keep the
MMC device order, set it back to HW order in U-Boot dtsi files.

[1] ab547c4fb39f ("arm64: dts: amlogic: Assign a fixed index to mmc devices")

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2021-10-07 10:14:50 +02:00
Neil Armstrong
2e8d47c641 ARM: meson: Sync Amlogic DT from Linux 5.14
Import Amlogic DT changes from Linux commit 7d2a07b76933 ("Linux 5.14"),
dt-bindings clock changes and new meson-g12b-gsking-x.dts,
meson-sm1-bananapi-m5 & odroid-hc4 boards.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2021-10-07 10:14:50 +02:00
Jan Kiszka
26fa063c6e iot2050: Enable watchdog support, but do not auto-start it
This allows to use the watchdog in custom scripts but does not enforce
that the OS has to support it as well.

Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
2021-10-03 14:40:56 -04:00
Jan Kiszka
c3a879510a arm: dts: Add IOT2050 device tree files
Prepares for the addition of the IOT2050 board which is based on the TI
AM65x. The board comes in four variants, Basic and Advanced, each as
product generation 1 (SR1.0) and 2 (SR2.x), so there are separate dts
files needed. Furthermore, the SPL has its own device tree.

Based on original board support by Le Jin, Gao Nian and Chao Zeng.

Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
2021-10-03 14:40:56 -04:00
Chia-Wei Wang
8e1ebdcfd7 ARM: dts: ast2600: Make WDT by default disabled
The WDT devices described in the general .dtsi file
should be marked as "disabled" by default.

A WDT should be then enabled in the board specific
.dts file on demands.

Signed-off-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
2021-10-03 11:59:22 -04:00
Tom Rini
fa09b12dc5 arm: ti: k3: Resync dts files and bindings with Linux Kernel v5.14
This resyncs the dts files for all of the currently in-tree K3
platforms, along with relevant bindings, with the v5.14 Linux Kernel
release.  Of note are that the main-navss/mcu-navss nodes were renamed
to main_navss / mcu_navss and so the u-boot.dtsi files needed to be
updated to match.

Tested on j721e_evm and am65x_evm.

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-10-03 11:59:22 -04:00
Tom Rini
8bef036836 Xilinx changes for v2022.01-rc1
zynq:
 - Enable capsule update for qspi and mmc
 - Update zed DT qspi compatible string
 
 zynqmp:
 - Add missing modeboot for EMMC
 - Add missing nand DT properties
 - List all eeproms for SC on vck190
 - Add vck190 SC psu_init
 
 clk:
 - Handle only GATE type clock for Versal
 
 watchdog:
 - Update versal driver to handle system reset
 -----BEGIN PGP SIGNATURE-----
 
 iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYVWWZgAKCRDKSWXLKUoM
 IY3MAJ43Mlut5tK9gv45bp4HpyVOMuSvJwCfTiVr7ZxrBE8I8QC5+zHzBTmuM6g=
 =aQtT
 -----END PGP SIGNATURE-----

Merge tag 'xilinx-for-v2022.01-rc1' of https://source.denx.de/u-boot/custodians/u-boot-microblaze into next

Xilinx changes for v2022.01-rc1

zynq:
- Enable capsule update for qspi and mmc
- Update zed DT qspi compatible string

zynqmp:
- Add missing modeboot for EMMC
- Add missing nand DT properties
- List all eeproms for SC on vck190
- Add vck190 SC psu_init

clk:
- Handle only GATE type clock for Versal

watchdog:
- Update versal driver to handle system reset
2021-09-30 11:29:41 -04:00
Wolfgang Denk
0cf207ec01 WS cleanup: remove SPACE(s) followed by TAB
Signed-off-by: Wolfgang Denk <wd@denx.de>
2021-09-30 09:08:16 -04:00
Wolfgang Denk
66356b4c06 WS cleanup: remove trailing empty lines
Signed-off-by: Wolfgang Denk <wd@denx.de>
2021-09-30 08:08:56 -04:00
Michal Simek
876b854a22 arm64: zynqmp: Define all eeproms for SC on vck190
There are multiple eeproms on vck190 that's why list all of them.
FMC eeproms are present only when fmcs are plugged.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/96902661e3ab9e20b59d626e6129ccf6f3317c4d.1632488695.git.michal.simek@xilinx.com
2021-09-30 12:29:49 +02:00
Michal Simek
3482ed6faf arm: zynq: Use s25fl256s1 compatible string on zedboard
Use compatible string which is listed in the Linux kernel.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/49bc6b056b0f6f69d4d90351dc875a66b7e37619.1631715748.git.michal.simek@xilinx.com
2021-09-30 12:29:08 +02:00
Amit Kumar Mahapatra
1a94d0554d arm64: zynqmp: Add device tree properties for nand flash
Add ecc strength & ecc step size properties for nand flash devices,
when operating in software-ecc mode.

Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/866f4b888129ff0213df9cdb51b5529b199fb7b7.1631713594.git.michal.simek@xilinx.com
2021-09-30 12:28:34 +02:00
Tom Rini
6eecaf5d0f Merge branch 'network_master' of https://source.denx.de/u-boot/custodians/u-boot-net into next
- Fix some non-NULL terminated strings in the networking subsystem
- net: tsec: Mark tsec_get_interface as __maybe_unused
2021-09-29 07:58:20 -04:00
Robert Marko
65513f3c18 arm: dts: armada8040: Fix CP0 eMMC/SDIO support
During the migration to a single DTSI for the CP110-s specific pinctrl
compatibles were moved to the SoC DTSI as CP0 and CP1 have some specifics.
Namely, CP0 eMMC/SDIO support depends on the mvebu-pinctrl driver setting
the BIT(0) in eMMC PHY IO Control 0 Register to 0 in order for the connect
the eMMC/SDIO PHY to the controller and not use it as a MPP pin multiplexor.

So, the mvebu-pinctrl driver check specifically for the
"marvell,armada-8k-cpm-pinctrl" compatible to clear the that bit.

Issue is that compatibles in the 8040 DTSI were set to "marvell,8k-cpm-pinctrl"
for CP0 and "marvell,8k-cps-pinctrl" for the CP1.
This is obviously incorrect as the pinctrl driver does not know about these.

So fix the regression by applying correct compatibles to the DTSI.
Regression found and tested on the Puzzle M801 board.

Fixes: a0ba97e5 ("arm: armada: dts: Use a single dtsi for cp110 die description")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
2021-09-29 07:13:27 +02:00
Rasmus Villemoes
24ea366add imx: imx7d-sdb: fix ethernet, sync .dts with linux
Commit 0d52bab46 (mx7dsabre: Enable DM_ETH) changed these flags from 0
(aka GPIO_ACTIVE_HIGH) to GPIO_ACTIVE_LOW. It claimed to "Also sync
device tree with v5.5-rc1", but in the linux tree, these gpios have
always been GPIO_ACTIVE_HIGH ever since this node was introduced
around v4.13 (linux commit 184f39b5).

I'm guessing that the reason for the GPIO_ACTIVE_LOW was to work
around the behaviour of the soft-spi driver back then, which
effectively defaulted to spi-mode 3 and not 0. That was arguably a bug
in the soft-spi driver, which then got fixed in 0e146993bb (spi: add
support for all spi modes with soft spi), but that commit then broke
ethernet on this board.

Fix it by setting the gpios as active high, which as a bonus actually
brings us in sync with the .dts in the linux source tree.

Without this, one gets

    Net:   Could not get PHY for FEC0: addr 0
    No ethernet found.

With this, ethernet (at least ping and tftp) works as expected from
the U-Boot shell.

Cc: Fabio Estevam <festevam@gmail.com>
Cc: Joris Offouga <offougajoris@gmail.com>
Cc: "Christian Bräuner Sørensen" <yocto@bsorensen.net>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
2021-09-28 12:03:21 -04:00
Vladimir Oltean
7c2d5d1642 net: freescale: replace usage of phy-mode = "sgmii-2500" with "2500base-x"
After the discussion here:
https://lore.kernel.org/netdev/20210603143453.if7hgifupx5k433b@pali/

which resulted in this patch:
https://patchwork.kernel.org/project/netdevbpf/patch/20210704134325.24842-1-pali@kernel.org/

and many other discussions before it, notably:
https://patchwork.kernel.org/project/linux-arm-kernel/patch/1512016235-15909-1-git-send-email-Bhaskar.Upadhaya@nxp.com/

it became apparent that nobody really knows what "SGMII 2500" is.
Certainly, Freescale/NXP hardware engineers name this protocol
"SGMII 2500" in the reference manuals, but the PCS devices do not
support any "SGMII" specific features when operating at the speed of
2500 Mbps, no in-band autoneg and no speed change via symbol replication
. So that leaves a fixed speed of 2500 Mbps using a coding of 8b/10b
with a SERDES lane frequency of 3.125 GHz. In fact, "SGMII 2500 without
in-band autoneg and at a fixed speed" is indistinguishable from
"2500base-x without in-band autoneg", which is precisely what these NXP
devices support.

So it just appears that "SGMII 2500" is an unclear name with no clear
definition that stuck.

As such, in the Linux kernel, the drivers which use this SERDES protocol
use the 2500base-x phy-mode.

This patch converts U-Boot to use 2500base-x too, or at least, as much
as it can.

Note that I would have really liked to delete PHY_INTERFACE_MODE_SGMII_2500
completely, but the mvpp2 driver seems to even distinguish between SGMII
2500 and 2500base-X. Namely, it enables in-band autoneg for one but not
the other, and forces flow control for one but not the other. This goes
back to the idea that maybe 2500base-X is a fiber protocol and SGMII-2500
is an MII protocol (connects a MAC to a PHY such as Aquantia), but the
two are practically indistinguishable through everything except use case.

NXP devices can support both use cases through an identical configuration,
for example RX flow control can be unconditionally enabled in order to
support rate adaptation performed by an Aquantia PHY. At least I can
find no indication in online documents published by Cisco which would
point towards "SGMII-2500" being an actual standard with an actual
definition, so I cannot say "yes, NXP devices support it".

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
2021-09-28 18:50:56 +03:00
Vladimir Oltean
77b11f7604 net: replace the "xfi" phy-mode with "10gbase-r"
As part of the effort of making U-Boot work with the same device tree as
Linux, there is an issue with the "xfi" phy-mode. To be precise, in
Linux there was a discussion (for those who have time to read:
https://lore.kernel.org/netdev/1576768881-24971-2-git-send-email-madalin.bucur@oss.nxp.com/)

which led to a patch:
https://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next.git/commit/?id=c114574ebfdf42f826776f717c8056a00fa94881

TL;DR: "xfi" was standardized in Linux as "10gbase-r".

This patch changes the relevant occurrences in U-Boot to use "10gbase-r"
instead of "xfi" wherever applicable.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
2021-09-28 18:50:56 +03:00
Vladimir Oltean
66fd01fe59 net: update NXP copyright text
NXP Legal insists that the following are not fine:

- Saying "NXP Semiconductors" instead of "NXP", since the company's
  registered name is "NXP"

- Putting a "(c)" sign in the copyright string

- Putting a comma in the copyright string

The only accepted copyright string format is "Copyright <year-range> NXP".

This patch changes the copyright headers in the networking files that
were sent by me, or derived from code sent by me.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
2021-09-28 18:50:56 +03:00
Marek Vasut
4a60d3571b arm: socfpga: vining: Fix UDC controller phandle in DT
The USB peripheral controller is the DWC2 controller 1, not 0.
Update the phandle to fix UDC support on this board.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
2021-09-28 18:50:55 +03:00
Marek Vasut
4527568e3f arm: socfpga: vining: Un-disable WDT in DT
The WDT on this system should be enabled, make it so.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
2021-09-28 18:50:55 +03:00
Tom Rini
f899cc1432 ti: keystone: Move away from CONFIG_SOC_KEYSTONE
We have individual SOC symbols for each keystone 2 platform.  Use the
existing CONFIG_ARCH_KEYSTONE rather than CONFIG_SOC_KEYSTONE to
encompass all of the keystone families.

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-09-27 21:38:34 -04:00
Tom Rini
e908d20fcb Prepare v2021.10-rc5
-----BEGIN PGP SIGNATURE-----
 
 iQGzBAABCgAdFiEEGjx/cOCPqxcHgJu/FHw5/5Y0tywFAmFRyIMACgkQFHw5/5Y0
 tyz1jgv/aTtHWVcGiw+nvvnnlgdrY4h9yVP5AfBLhOR7ogYOw2B9xHmdh+9oCas9
 Rt45AC4nFvUszxCPJqg36kjljTKRVapemHqhCbgGGeb9GYMkNb1zjk79WnuqgeJy
 ydBUCh1NQI5pOvrpDv7kWRx1IyDi/gUgQO3RBdufbunNmn4Zj4jlw5RmMTgDACRC
 cvTr39gVQq1LOzL2W7+XkSfiEejtGERNs32Nt+jzyAm5a2PkngULUnPW6WsHu+qy
 5YJTR50TK55QgPIdoiqY14BUDpqEbHlNKsE7p6hHkDf6XSS7gLHYW2tVVt2Z8ocg
 9cW35Qotov7MeiSClc3SIEPiIefwh2oTVf0uYoP+uvlRAComvcIzphq68NIQe6Av
 es+ZJI1Qx5ERvDQMMW3xOHTlcBGgpqA0Y/QVr62rE8bEzK/1gvTiP+hVVqzUrnHJ
 f3ZAVt16clIfXKAxGsW4Am05iMmT+rtcS5IrUMuEzmkb0KK58YXsOVmsKHLX9aI1
 T74ewXfu
 =y67Q
 -----END PGP SIGNATURE-----

Merge tag 'v2021.10-rc5' into next

Prepare v2021.10-rc5
2021-09-27 09:45:36 -04:00
Kristian Amlie
15e30106ce ARM: vexpress_ca9x4: Reintroduce board in order to use with QEMU.
vexpress_ca9x4 is seemingly the only board except for qemu_arm which
is able to run U-Boot correctly, using the `-M vexpress-a9` option to
QEMU. Building for qemu_arm and running qemu-system-arm with the `-M
virt` argument has a number of downsides, most importantly that it
only supports virtio storage drivers. This significantly reduces its
usefulness in testing memory card and Flash solutions, especially when
the tested images are from a third party source.

So therefore we reintroduce the vexpress_ca9x4 board in this commit,
with the explicit goal of using it with QEMU.

A number of differences to note from the original:

* Since the board was apparently unmaintained, I have now set myself
  as the maintainer.

* The board has been converted to use the driver model, which was the
  reason it was removed in the first place.

* The vexpress_ca15_tc2 and vexpress_ca5x2 boards, which were removed
  in the same commit, are not necessary for the QEMU use case, and
  have been omitted.

* An `mmc0` alias was introduced in the dts file. The mmc is not
  detected correctly without this, now that it's based on the device
  tree instead of the board's init function.

* A couple of other nodes were removed because they were problematic
  when trying to run the UEFI bootmgr. Once again, the primary use
  case here is QEMU, and these nodes are not needed for that to work.

* Unnecessary board init code has been removed, thanks to driver model
  and device tree.

* `CONFIG_OF_EMBED` has been enabled. I know this goes against
  recommended practice, but there doesn't seem to be any other way to
  pass the dtb to U-Boot in the QEMU scenario. Using the -dtb argument
  does not work, I suppose because U-Boot doesn't use the same
  mechanics as the kernel when it's booting.

* Load addresses have been changed to fit QEMU use case.

People wanting to get a more detailed, yet somewhat isolated, diff
between this and the original, can run this command:

  git diff c6c26a05b89f25a06e7562f8c2071b60fd0c9eac~1 -- \
      $( git diff-tree --diff-filter=A -r --name-only HEAD~1 HEAD)

(Make sure to either check out this commit first, or replace HEAD with
the commit ID of this commit)

Signed-off-by: Kristian Amlie <kristian.amlie@northern.tech>
2021-09-24 14:30:46 -04:00
Marek Vasut
c3880e6597 arm: socfpga: vining: Fix UDC controller phandle in DT
The USB peripheral controller is the DWC2 controller 1, not 0.
Update the phandle to fix UDC support on this board.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
2021-09-22 21:30:39 +02:00
Marek Vasut
e21bbffa1d arm: socfpga: vining: Un-disable WDT in DT
The WDT on this system should be enabled, make it so.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
2021-09-22 21:30:39 +02:00
Patrick Delaunay
cf39d0c29d arm: dts: stm32mp1: use ssbl partition name for U-Boot
Continue to use the "ssbl" name for GPT partition of secondary boot
stage = U-Boot for basic boot with SPL to avoid to disturb existing user.

The "fip" partition name is only used for TFA_BOOT with FIP, it is a TF-A
BL2 requirement; it the default configuration for STMicroelectronics
boards.

Fixes: b73e8bf453 ("arm: stm32mp: add defconfig for trusted boot with FIP")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
2021-09-21 09:22:01 +02:00
Eugen Hristev
d65b84a1d0 ARM: dts: at91: update flexcom defines using include file
Replace the number in the flexcom-mode property with the define from the
include file.
This corresponds to the approach in Linux kernel.

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2021-09-21 10:08:24 +03:00
Eugen Hristev
26671aabcc ARM: dts: at91: sama5d2: fix dtc warning for ohci and ehci
Fixed the following DTC build warning (reproducible with W=1)

arch/arm/dts/at91-sama5d2_icp.dtb: Warning (unit_address_format): /ahb/ohci@00400000: unit name should not have leading 0s
arch/arm/dts/at91-sama5d2_icp.dtb: Warning (unit_address_format): /ahb/ehci@00500000: unit name should not have leading 0s

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Alexander Dahl <ada@thorsis.com>
2021-09-21 10:05:38 +03:00
Eugen Hristev
b6a8cce941 ARM: dts: at91: sama5d2_icp: cosmetic arrangement of the nodes
Reorder the nodes following the kernel rules: nodes in a range are sorted
by ascending bus address, and when referenced by phandle, are ordered
alphabetically.

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2021-09-21 10:05:38 +03:00
Mihai Sain
5b43508419 ARM: dts: at91: sama5d2_icp: add QSPI1 device
Add support for sst26vf064b 64Mbit qspi-flash that is
present on sama5d2_icp board.

Signed-off-by: Mihai Sain <mihai.sain@microchip.com>
[eugen.hristev@microchip.com: move u-boot properties to sama5d2_icp-u-boot.dtsi]
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2021-09-21 10:05:38 +03:00
Clément Léger
b25d7618be ARM: dts: at91: sama5d2_xplained: Add memory node in devicetree
sama5d2_xplained DRAM detection code will be modified to use device tree
instead of hardcoded addresses. In order to prepare that, add the memory
node to at91-sama5d2_xplained.dts.

Signed-off-by: Clément Léger <clement.leger@bootlin.com>
2021-09-21 10:05:38 +03:00
Claudiu Beznea
63ba551d70 ARM: dts: at91: sam9x60: add bindings for CPU
Add bindings for CPU. This will allow displaying correctly the crystal,
CPU and master clock.

Reported-by: Eugen Hristev <eugen.hristev@microchip.com>
Fixes: a64862284f ("clk: at91: sam9x60: add support compatible with
CCF")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
2021-09-21 10:05:37 +03:00
Tom Rini
6674edaabf Prepare v2021.10-rc4
-----BEGIN PGP SIGNATURE-----
 
 iQGzBAABCgAdFiEEGjx/cOCPqxcHgJu/FHw5/5Y0tywFAmFBKRgACgkQFHw5/5Y0
 tyw/PwwAtGB3rBeYW4rjWuMC5WP1UDTnvZIAok5ImWumWDahjDm8Yq2VCzAe9adw
 EYBjuNmaNl9aQvGVqlVJeIcLku5MLuLQu2za8vhc1R8X9VTPPY+LLTcdOokOmB8y
 8JiaE7fJsb1bZeV+diF9tss3B0IkUrwSJtW1d+qfdz/4UiRvwK5BhnZgzIobDldO
 g1Ldz/xiR2GOAXlUMwDrNAi6qNvmeAqRsQxySVrjltAV2ST7LJnOiHuWvJX6g6VS
 l796Hleh/kULfEW6n+1ZaTNqvVRcJ8xYSOG8w8y9u6HuPBA3JrYH1p1Eo5n7PPDv
 US71Iy/ncweTyfTMEBThWLqjHOQ05sVkWX/r4fj2iJRli+Og53lE1fVJ4ajIx7vz
 Tc76wI43i0I5lr2yTErjUG6EzDDoueqd+c8BwxihNLUK/+QG31xoCEMfC80C25ro
 QhYVFgiPWN0ySUD5M5tbGXODvfNNIDKXpY5oSOTVtemZtDEMpO2zBM1s/K3RV7Ud
 Je9Pj0Cu
 =Me42
 -----END PGP SIGNATURE-----

Merge tag 'v2021.10-rc4' into next

Prepare v2021.10-rc4

Signed-off-by: Tom Rini <trini@konsulko.com>

# gpg: Signature made Tue 14 Sep 2021 06:58:32 PM EDT
# gpg:                using RSA key 1A3C7F70E08FAB1707809BBF147C39FF9634B72C
# gpg: Good signature from "Thomas Rini <trini@konsulko.com>" [ultimate]

# Conflicts:
#	board/Arcturus/ucp1020/spl.c
#	cmd/mvebu/Kconfig
#	common/Kconfig.boot
#	common/image-fit.c
#	configs/UCP1020_defconfig
#	configs/sifive_unmatched_defconfig
#	drivers/pci/Kconfig
#	include/configs/UCP1020.h
#	include/configs/sifive-unmatched.h
#	lib/Makefile
#	scripts/config_whitelist.txt
2021-09-16 10:29:40 -04:00
Matthias Brugger
3304197272 arm: dts: bcm283x: Add minimal smbios information
At present SMBIOS tables are empty, which breaks some use-cases that
rely on that. Add some minimal information to fulfill this.

Signed-off-by: Matthias Brugger <mbrugger@suse.com>
2021-09-15 12:29:26 +02:00
Aswath Govindraju
fa7a14576d arm: dts: k3-j721e-r5-*.dts: Fix clock-names property in the usb0 instance
In the cdns3 usb driver, the clock name looked for is ref. Therefore, fix
the clock-names property in usb0 instance for proper initialization of
cdns3 usb gadget driver.

Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
2021-09-10 20:10:20 -04:00
Roger Quadros
72f78c6918 ARM: dts: Fix node status to "okay" on TI boards
As per Device Tree Specification [1], the status parameter of nodes can
be "okay", "disabled", etc. "ok" is not a valid parameter.

U-boot Driver Model does not recognize status="ok" either and treats
the node as disabled.

[1] https://github.com/devicetree-org/devicetree-specification/releases/tag/v0.3

Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
2021-09-10 20:10:20 -04:00
Aswath Govindraju
7ca1af635a arm: dts: k3-am642-evm-u-boot: Add u-boot, dm-spl tag in the pinmux node of mmc1
Add u-boot,dm-spl tag in the pinmux device tree node, required for MMCSD1
subsystem.

Fixes: b6059ddc45 ("arm: dts: k3-am642: Add r5 specific dt support")
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
2021-09-10 20:10:20 -04:00
Matwey V. Kornilov
4c9289f52f am33xx: Fix USB for am335x boards
USB nodes were mistakenly disabled in

    commit 942853dd96 ("arm: dts: Resync BeagleBone device trees")

This commit is to fix the following issue:

    starting USB...
    No working controllers found
    USB is stopped. Please issue 'usb start' first.
    starting USB...
    No working controllers found

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=0782e8572ce43f521ed6ff15e4a7ab9aa5acdc85
Fixes: 942853dd96 ("arm: dts: Resync BeagleBone device trees")
Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Reviewed-by: Paul Barker <paul.barker@sancloud.com>
2021-09-10 20:10:20 -04:00
Sven Auhagen
88426bd6b0 arm: mvebu: dts: Armada8k enable mdio
Since mvpp2 is using the new mdio driver and the cp110 has been
synced with the linux upstream, the mdio has to enabled in the
device tree file.
This is missing for some device tree files and therefore the
network cards do not come online.

Signed-off-by: Sven Auhagen <sven.auhagen@voleatech.de>
Reviewed-by: Stefan Roese <sr@denx.de>
2021-09-10 09:01:51 +02:00
Stephan Gerhold
f64011e11e board: stemmy: Add basic Fastboot support
Make use of the new drivers for ARM U8500 introduced in the U-Boot
2021.10 merge window by adding basic support for USB Fastboot with
the "stemmy" board. As a first step this will always boot directly
into USB Fastboot for now with the console displayed on the screen
to make that obvious.

Samsung uses quite strange GPT partition labels on these boards,
so also add a bunch of fastboot_partition_alias_* to make this more
easy to use.

Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
2021-09-01 19:25:37 -04:00
Stephan Gerhold
fc9d4b123d arm: dts: u8500: u-boot: Add fixed clock for eMMC
So far there is no need for a clock driver in U-Boot because the
previous boot stage leaves all the necessary clocks on. However,
some drivers in U-Boot (e.g. arm_pl180_mmci) depend on having a clock
driver to obtain the clock frequency.

Setting up the clock drivers properly is a bit tricky on U8500,
so for now add a simple fixed-clock for the eMMC that allows obtaining
the clock frequency. This should be replaced eventually if some board
actually requires enabling some of the clocks.

Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
2021-09-01 19:25:37 -04:00
Stephan Gerhold
1ae43a0e23 arm: dts: u8500: Update from Linux ux500-dts-for-v5.15
Update ste-dbx5x0.dtsi, ste-ab8500.dtsi and ste-ab8505.dtsi with
the changes made in upstream Linux. They are taken from
https://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik.git/
branch "ux500-dts-for-v5.15" (pending merge for Linux 5.15).

The only relevant change for U-Boot here is
"ARM: dts: ux500: ab8500: Link USB PHY to USB controller node" [1]
which links the USB PHY to the USB controller. This is necessary on
U-Boot because the PHY driver is implemented as part of the generic
PHY subsystem that makes use of these bindings.

[1]: https://lore.kernel.org/linux-arm-kernel/20210709182234.47232-1-stephan@gerhold.net/

Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
2021-09-01 19:25:37 -04:00
Tom Rini
b15a17be0c Merge https://gitlab.denx.de/u-boot/custodians/u-boot-sh 2021-08-31 18:37:25 -04:00
Tom Rini
b9cb74a5aa Xilinx changes for v2021.10-rc3
xilinx:
 - Disable CONFIG_ARCH_FIXUP_FDT_MEMORY
 - Print information about cpu via soc drivers and enable DISPLAY_CPUINFO
 - Wire infrastructure for DTB_RESELECT and MULTI_DTB_FIT
 
 zynq:
 - Wire single QSPI
 - Use power-source instead of io-standard properties
 - Enable nor on zc770-xm012
 
 zynqmp:
 - Change handling around multi_boot()
 - Setup offset for u-boot.itb in spi
 - Generate run time dfu_alt_info for capsule update
 - Use explicit values for enums (zynqmp_firmware.h)
 - Enable RTC/SHA1/BUTTON/BUTTON_GPIO command
 - Disable WDT driver by default
 - Bind usb/scsi via preboot because of EFI
 - DT updates/fixes
 - Add soc driver
 - Fix SPL SPI boot mode
 
 versal:
 - Add soc driver
 
 sdhci:
 - Update tap delay programming for zynq_sdhci driver
 
 cmd:
 - Fix RTC uclass handling in date command
 - Update pwm help message
 - Update reset help message
 
 watchdog:
 - Fix wwdt compilation
 
 rtc:
 - Deal with seq alias in rtc uclass
 - Add zynqmp RTC driver
 
 fdt:
 - Add kernel-doc for fdt_fixup_memory_banks()
 -----BEGIN PGP SIGNATURE-----
 
 iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYSilpgAKCRDKSWXLKUoM
 Id2JAJ9jY19JiEpOd3vuRCT5CE/pzX4yDACeP8DiXDzSi5tLHwDWUCBobUTze2s=
 =5lnj
 -----END PGP SIGNATURE-----

Merge tag 'xilinx-for-v2021.10-rc3' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze

Xilinx changes for v2021.10-rc3

xilinx:
- Disable CONFIG_ARCH_FIXUP_FDT_MEMORY
- Print information about cpu via soc drivers and enable DISPLAY_CPUINFO
- Wire infrastructure for DTB_RESELECT and MULTI_DTB_FIT

zynq:
- Wire single QSPI
- Use power-source instead of io-standard properties
- Enable nor on zc770-xm012

zynqmp:
- Change handling around multi_boot()
- Setup offset for u-boot.itb in spi
- Generate run time dfu_alt_info for capsule update
- Use explicit values for enums (zynqmp_firmware.h)
- Enable RTC/SHA1/BUTTON/BUTTON_GPIO command
- Disable WDT driver by default
- Bind usb/scsi via preboot because of EFI
- DT updates/fixes
- Add soc driver
- Fix SPL SPI boot mode

versal:
- Add soc driver

sdhci:
- Update tap delay programming for zynq_sdhci driver

cmd:
- Fix RTC uclass handling in date command
- Update pwm help message
- Update reset help message

watchdog:
- Fix wwdt compilation

rtc:
- Deal with seq alias in rtc uclass
- Add zynqmp RTC driver

fdt:
- Add kernel-doc for fdt_fixup_memory_banks()
2021-08-27 08:33:02 -04:00
Michal Simek
52ff1626cf xilinx: common: Enabling generic function for DT reselection
U-Boot support board detection at run time and based on it change DT.
This feature is implemented for SOM Kria platforms which contain two
eeproms which contain information about SOM module and CC (Carrier card).
Full U-Boot starts with minimal DT file defined by
CONFIG_DEFAULT_DEVICE_TREE which is available in multi DTB fit image.
It is using default setup of board_name variable initializaed to
DEVICE_TREE which corresponds to CONFIG_DEFAULT_DEVICE_TREE option.

When DTB_RESELECT is enabled board_detection() is called. Keep it your mind
that this code is called before relocation. board_detection() is calling
xilinx_read_eeprom() which fills board_info (xilinx_board_description)
structure which are parsed in board_name_decode().
Based on DT configuration and amount of nvmemX aliases name of the board is
composed by concatenating CONFIG_SYS_BOARD "-" <board_name> "-rev"
<board_revision> "-" <cc_name> "-rev" <cc_revision>.

If CC is not present or more are available it keeps going.

When board name is composed and returned from board_name_decode() it is
assigned to board_name variable which is used by
board_fit_config_name_match() which is called via fdtdec_setup() when it
goes over config options in multi dtb FIT image.

From practical point of view multi DTB image is key point here which has to
contain configs for detected combinations. Unfortunately as of now they
have to be full DTBs and DTBOs are not supported.

That's why configuration like:
config_X {
	description = "zynqmp-board-cc";
	fdt = "board", "cc";
};

needs to be squashed together with:
fdtoverlay -o zynqmp-board-cc -i arch/arm/dts/zynqmp-board.dtb \
arch/arm/dts/zynqmp-cc.dtbo

and only one dtb is in fit:
config_X {
	description = "zynqmp-board-cc";
	fdt = "board-cc";
};

For creating multi DTBs fit image use mkimage -E, e.g.:
mkimage -E -f all.its all.dtb

When DTB_RESELECT is enabled xilinx_read_eeprom() is called before
relocation and it uses calloc for getting a buffer. Because this is dynamic
memory it is not relocated that's why xilinx_read_eeprom() is called again
as the part of board_init(). This second read with calloc buffer placed in
proper position board_late_init_xilinx() can setup u-boot variables as
before.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-08-26 08:14:43 +02:00
Michal Simek
f28a22d55a arm64: dts: Make sure that all DTBs are 64bit aligned
Start of DTB should be 64bit aligned that's why also make sure that end is
also 64bit aligned. It is not required but it is nice thing to do.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-08-26 08:14:43 +02:00
Michal Simek
c2b7244322 ARM: zynq: Enable smcc and nor for zc770-xm012
Enable cfi flash on zc770-xm012 configuration.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-08-26 08:08:11 +02:00
Michal Simek
0df062bf04 ARM: zynq: Wire single qspi on couple of boards
Single configuration is working fine and no issue to enable it.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-08-26 08:08:11 +02:00
Sai Krishna Potthuri
b9c4e8d439 ARM: zynq: Replace 'io-standard' with 'power-source' property
Replace 'io-standard' property with 'power-source' property in all
zynq dts files to be in sync with Zynq Pinctrl driver.

Signed-off-by: Sai Krishna Potthuri <lakshmi.sai.krishna.potthuri@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-08-26 08:08:11 +02:00
Raju Kumar Pothuraju
bc353102a0 xilinx: Add jedec compatible string for QSPI (Zynq/ZynqMP)
Add missing "jedec, spi-nor" compatible string for QSPI flash node.
Spi-nor framework uses this compatibility string to probe &
initialize flash. With missing compatibility string we are observing
below error:

Zynq> sf probe 0 0 0
 jedec_spi_nor spi_flash@0:0: unrecognized JEDEC id bytes:
00, 00, 00  Failed to initialize SPI flash at 0:0 (error -2)

Signed-off-by: Raju Kumar Pothuraju <raju.kumar-pothuraju@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-08-26 08:08:11 +02:00
Michal Simek
1759a31288 arm64: zynqmp: Update comment style sm-k26
Trivial style patch.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-08-26 08:08:11 +02:00
Michal Simek
464f6558ca arm64: zynqmp: Fix header alignment on kv260 boards
Fix header alignment.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-08-26 08:08:11 +02:00
Michal Simek
4cec057ff9 arm64: zynqmp: Fix node name for ds35/36 leds
By dt-binding specs led nodes should have -led suffix that's why add it.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-08-26 08:08:11 +02:00
Siew Chin Lim
8208e9a914 arm: dts: Add base dtsi and devkit dts for Intel N5X device
Add device tree for N5X.

Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Ley Foon Tan <lftan.linux@gmail.com>
2021-08-25 15:04:44 +08:00
Adam Ford
221146c558 ARM: rmobile: beacon-renesom: Enable QSPI NOR Flash
There is a QSPI NOR flash part on the board.  Because this chip isn't
yet supported in Linux, but it is supported in U-Boot, and the
face that the RPC_SPI compatible names are different in U-Boot and
Linux, the device tree updates are confined to -u-boot.dtsi files.

In order to use the QSPI, TF-A must leave RPC unlocked by compiling
TF-A with RZG_RPC_HYPERFLASH_LOCKED=0.

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Biju Bas <biju.das.jz@bp.renesas.com>
2021-08-24 20:03:09 +02:00
Michael Walle
8331618cc3 board: sl28: drop unneeded and outdated flash partitions
This board doesn't use the MTD subsystem in u-boot, thus there is no
need to specify the partitions. They are outdated anyway. Just drop
them.

Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-08-18 15:55:15 +05:30
Marek Vasut
59f6eb477e ARM: dts: stm32: Reduce DHCOR SPI NOR frequency to 50 MHz
The SPI NOR is a bit further away from the SoC on DHCOR than on DHCOM,
which causes additional signal delay. At 108 MHz, this delay triggers
a sporadic issue where the first bit of RX data is not received by the
QSPI controller.

There are two options of addressing this problem, either by using the
DLYB block to compensate the extra delay, or by reducing the QSPI bus
clock frequency. The former requires calibration and that is overly
complex for SPL, so opt for the second option. This incurs 20ms delay
during boot, when SPL loads U-Boot to DRAM.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
2021-08-16 10:49:35 +02:00
Patrick Delaunay
2d4180b1eb arm: dts: stm32mp15: alignment with v5.14
Device tree alignment with Linux kernel v5.14-rc3
- ARM: dts: stm32: move stmmac axi config in ethernet node on stm32mp15
- ARM: dts: stm32: Configure qspi's mdma transfer to block for stm32mp151
- ARM: dts: stm32: add a new DCMI pins group on stm32mp15
- ARM: dts: stm32: fix ltdc pinctrl on microdev2.0-of7

Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
2021-08-16 10:49:35 +02:00
Patrick Delaunay
b73e8bf453 arm: stm32mp: add defconfig for trusted boot with FIP
Add TF-A FIP support for trusted boot on STM32MP15x,
when STM32MP15x_STM32IMAGE is not activated.

With FIP support the SSBL partition is named "fip" and its size is 4MB,
so the ENV partition name in device tree  (for SD card or eMMC)
or offset in defconfig (CONFIG_ENV_OFFSET / CONFIG_ENV_OFFSET_REDUND)
need to be modified.

With FIP the TEE MTD partitions are removed because the OP-TEE binray are
included in the FIP containers.

Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
2021-08-16 09:36:31 +02:00
Patrick Delaunay
f91783edf2 arm: stm32mp: handle the OP-TEE nodes in DT with FIP support
With FIP support in TF-A (when CONFIG_STM32MP15x_STM32IMAGE
is not activated), the DT nodes needed by OP-TEE are added by OP-TEE
firmware in U-Boot device tree, present in FIP.

These nodes are only required in trusted boot, when TF-A load the file
u-boot.stm32, including the U-Boot device tree with STM32IMAGE header,
in this case OP-TEE can't update the U-Boot device tree.

Moreover in trusted boot mode with FIP, as the OP-TEE nodes are present
in U-Boot device tree only when needed the function
stm32_fdt_disable_optee can be removed.

Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
2021-08-16 09:34:27 +02:00
Chris Morgan
d70c0cab8f rockchip: px30: add support for SFC for Odroid Go Advance
The Odroid Go Advance uses a Rockchip Serial Flash Controller with an
XT25F128B SPI NOR flash chip. This adds support for both. Note that
while both the controller and chip support quad mode, only two lines
are connected to the chip. Changing the pinctrl to bus2 and setting tx
and rx lines to 2 for this reason.

Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2021-08-12 09:34:11 +08:00
Chris Morgan
08b097c32f rockchip: px30: add the serial flash controller
Add the serial flash controller to the devicetree for the PX30.

Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2021-08-12 09:34:11 +08:00
Peter Robinson
100583473c arm: dts: sync the Rockhip 3368 SoCs from Linux
Sync the rk3368 DTs and associated bits from 5.14-rc1.

Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2021-08-12 09:33:13 +08:00
Peter Robinson
27e1b5ee9b arm: dts: sync the Rockhip 3328 SoCs from Linux
Sync the rk3328 DTs and associated bits from 5.14-rc1.

Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2021-08-12 09:33:13 +08:00
Peter Robinson
822556a934 arm: dts: sync the Rockhip 3399 SoCs from Linux
Sync the rk3399 DTs and associated bits from 5.14-rc1.

Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
(Remove the conflict content for vmarc-som)
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2021-08-12 09:33:13 +08:00
Xiaobo Tian
09cf012467 arm64: rk3399: r4s: Remove undesirable MAC address fetching methods for ethernet
Remove the recommended MAC address from the network card.
NanoPi R4S has a EEPROM attached to the 2nd I2C bus (U92), which stores the MAC address.

Signed-off-by: Xiaobo Tian <peterwillcn@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2021-08-11 18:10:39 +08:00
Xiaobo Tian
897f30e84a arm64: rk3399: r4s: Inheritance uses the sdmmc definition in dtsi
The host-index-min property is invalid,
so it inherits from the sdmmc definition in dtsi.

Signed-off-by: Xiaobo Tian <peterwillcn@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2021-08-11 18:10:39 +08:00
Xiaobo Tian
2ae7dacfaf arm64: rk3399: r4s: correct the LEDS label name
Correct the LEDS label name and remove the board type prefix,
which is actually unnecessary here, removes the redefined system status LED pin.

Signed-off-by: Xiaobo Tian <peterwillcn@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2021-08-11 18:10:39 +08:00
Johan Jonker
d2a74ec91b ARM: dts: rockchip: update rk3188-radxarock.dts
In the Linux DT the file rk3xxx.dtsi is shared between
rk3066 and rk3188. Both rk3xxx.dtsi and rk3188.dtsi have recently
had some updates.
For a future rk3066 support in U-boot this file must also update.
Move U-boot specific things in a rk3188-radxarock-u-boot.dtsi file.

Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2021-08-11 17:54:37 +08:00
Johan Jonker
7d4b5a850e ARM: dts: rockchip: update rk3188.dtsi
In the Linux DT the file rk3xxx.dtsi is shared between
rk3066 and rk3188. Both rk3xxx.dtsi and rk3188.dtsi have recently
had some updates.
For a future rk3066 support in U-boot this file must also update.
Move U-boot specific things in a rk3188-u-boot.dtsi file.

Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2021-08-11 17:54:37 +08:00
Johan Jonker
2ee023d293 ARM: dts: rockchip: update rk3xxx.dtsi
In the Linux DT the file rk3xxx.dtsi is shared between
rk3066 and rk3188. This file has recently had some updates.
For a future rk3066 support in U-boot this file must also update.
Move U-boot specific things in a rk3xxx-u-boot.dtsi file.

Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2021-08-11 17:54:37 +08:00
Peng Fan
3f2b4d7220 arm: imx: add i.MX8ULP EVK support
Add i.MX8ULP EVK basic support, support SD/I2C/ENET/LPUART

Log as below: I would keep some debug info for now, and after we move
to be stable and production launch, we could drop that.

U-Boot SPL 2021.07-rc4-00164-gb800e19a6b (Jun 29 2021 - 10:23:30 +0800)
Normal Boot
upower_init: soc_id=48
upower_init: version:11.11.6
upower_init: start uPower RAM service
user_upwr_rdy_callb: soc=b
user_upwr_rdy_callb: RAM version:12.6
Turn on switches ok
Turn on memories ok
Clear DDR retention ok
Poll for freq_chg_req on SIM register and change to F1 frequency.
Poll for freq_chg_req on SIM register and change to F0 frequency.
Poll for freq_chg_req on SIM register and change to F1 frequency.
Poll for freq_chg_req on SIM register and change to F2 frequency.
Poll for freq_chg_req on SIM register and change to F1 frequency.
Poll for freq_chg_req on SIM register and change to F2 frequency.
complete
De-Skew PLL is locked and ready
WDT:   Not found!
Trying to boot from BOOTROM
image offset 0x8000, pagesize 0x200, ivt offset 0x0
Load image from 0x3a800 by ROM_API
NOTICE:  BL31: v2.4(release):imx_5.10.35_2.0.0_imx8ulp_er-10-gf37e59b94
NOTICE:  BL31: Built : 01:56:58, Jun 29 2021
NOTICE:  upower_init: start uPower RAM service
NOTICE:  user_upwr_rdy_callb: soc=b
NOTICE:  user_upwr_rdy_callb: RAM version:12.6

U-Boot 2021.07-rc4-00164-gb800e19a6b (Jun 29 2021 - 10:23:30 +0800)

CPU:   Freescale i.MX8ULP rev1.0 at 744 MHz
Reset cause: POR
Boot mode: Single boot
Model: FSL i.MX8ULP EVK
DRAM:  2 GiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 2
Loading Environment from MMC... ***
Warning - bad CRC, using default environment

In:    serial@293a0000
Out:   serial@293a0000
Err:   serial@293a0000
Net:
Warning: ethernet@29950000 (eth0) using random MAC address -
96:35:88:62:e0:44
eth0: ethernet@29950000
Hit any key to stop autoboot:  0

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2021-08-09 14:46:51 +02:00
Peng Fan
6beec0e78c arm: dts: add i.MX8ULP dtsi
Add i.MX8ULP dtsi

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2021-08-09 14:46:51 +02:00
Fabio Estevam
1d1f3c8099 mx28evk: Convert to driver model
Make the conversion to driver model as it is mandatory.

Successfully tested booting Linux from the SD card.

Dropped support for networking and splash screen as these need
to be properly converted to DM and tested.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
2021-08-09 14:46:50 +02:00
Sebastian Reichel
3bbc48e8f1 board: ge: bx50v3: Add PCIe reset to DT
Add PCIe reset gpio to the Bx50v3 devicetree and get get rid of
CONFIG_PCIE_IMX_PERST_GPIO.

Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
2021-08-09 14:46:50 +02:00
Tim Harvey
a8a72c3ce9 board: gateworks: venice: add imx8mm-gw7902 support
The GW7902 is based on the i.MX 8M Mini / Nano SoC featuring:
- LPDDR4 DRAM
- eMMC FLASH
- Gateworks System Controller
- LTE CAT M1 modem
- USB 2.0 HUB
- M.2 Socket with USB2.0, PCIe, and dual-SIM
- IMX8M FEC
- PCIe based GbE
- RS232/RS485/RS422 serial transceiver
- GPS
- CAN bus
- WiFi / Bluetooth
- MIPI header (DSI/CSI/GPIO/PWM/I2S)
- PMIC

Do the following to add support for it:
- add dts
- add PMIC config

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-08-09 14:46:50 +02:00
Tim Harvey
42bc70d14a arm: dts: imx8mm-venice-gw7901: use common u-boot dtsi
Use the common imx8mm-u-boot.dtsi

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-08-09 14:46:50 +02:00
Tim Harvey
aea162c10e arm: dts: imx8mm-venice-gw700x: fix fifo-depth phy props
Replace the deprecated 'tx-fifo-depth' and 'rx-fifo-depth' properties
not supported by U-Boot drivers/net/phy/dp83867.c with the proper
'ti,fifo-depth' property.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-08-09 14:46:50 +02:00
Tim Harvey
98559e02f1 arm: dts: imx8mm-venice-gw71xx: fix USB OTG VBUS
The GW71xx has a USB Type-C connector with USB 2.0 signaling. GPIO1_12
is the power-enable to the TPS25821 Source controller and power switch
responsible for monitoring the CC pins and enabling VBUS. Therefore
GPIO1_12 must always be enabled and the vbus output enable from the
IMX8MM can be ignored.

To fix USB OTG VBUS enable a pull-up on GPIO1_12 to always power the
TPS25821 and change the regulator output to GPIO1_10 which is
unconnected.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-08-09 14:46:50 +02:00
Tim Harvey
a194e6ed45 imx: ventana: remove hard-coded USB OTG pinmux
pinmux is now done via dt. Add missing OTG_OC pinmux for boards that
use it.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-08-09 14:46:50 +02:00
Tim Harvey
dd79c97b92 imx: ventana: fix UMS support
The Gateworks Ventana boards have always had usb0=usbh1 and usb1=usbotg
because OTG is often subloaded on these boards and a bit in the EEPROM
which flagging that OTG is subloaded is used to remove the dt node via the
alias.

U-Boot DM_USB UMS requires the usb0 alias be assigned to the usbotg
so fix the usb0 alias in order for UMS to work.

Fixes 72c46327f0: ("imx: ventana: enable dm support for USB")

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-08-09 14:46:50 +02:00
Fabio Estevam
3f24bd329b imx28-evk: Import devicetree file from Linux
Import the imx28-evk devicetree files from Linux kernel
version 5.11-rc7.

This is in preparation for converting the mx28evk_defconfig
target to driver model.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
2021-08-06 13:26:08 +02:00
Tom Rini
b91c704333 Merge https://source.denx.de/u-boot/custodians/u-boot-samsung 2021-08-03 09:07:01 -04:00
Tom Rini
5371593aed Merge https://source.denx.de/u-boot/custodians/u-boot-sunxi
- Move the PSCI runtime code for H3/A23/A33 into SRAM
- Pick the environment from the actual MMC boot device (SD card vs.
  eMMC)
- Plus a small improvement from Icenowy, just for good measure.
2021-07-31 20:51:24 -04:00
Icenowy Zheng
001ec430be sunxi: decide the inclusion of SCP by SCP_ADDR existence
There are more Allwinner SoCs that do not have a SCP now.

When there's no SCP_ADDR macro defined, we can assume there's no SCP
available.

Drop the scp part of FIT description when SCP_ADDR does not exist.

Signed-off-by: Icenowy Zheng <icenowy@sipeed.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-08-01 00:11:34 +01:00
Tom Rini
38436abd5e Merge tag 'ti-v2021.10-rc2' of https://source.denx.de/u-boot/custodians/u-boot-ti
- Add MMC High speed modes for AM64 and J7200
- Add Sierra/Torrent SERDES driver
- Minor clean-ups for R5F boot from SPL
2021-07-29 08:20:06 -04:00
Tom Rini
55efa84d0f - Add SMBIOS info for Khadas VIM boards
- Fix meson-axg-mipi PHY build
 - Fix VIM3 board phy-names property setup
 - Return correct value for non emmc boot sources on VIM3
 - add kernel compression vars
 -----BEGIN PGP SIGNATURE-----
 
 iQIzBAABCgAdFiEEPVPGJshWBf4d9CyLd9zb2sjISdEFAmD/0m0ACgkQd9zb2sjI
 SdHOuhAAzKV5VKWFjz+kxAWLhIeVqK1DixVkA8qMLNE9LYfF2ibv89yM0jaTQv84
 Zs4J9ak9xC2/LQPX7ui9CzAZ53yi7qM28aQd4MzRPBha0al8dehRZdcGNTRV/WBb
 CnbwW5inx2J1e+KSZ2PVqOnCTVX39ZMdEbZnxIJmSCcgrwj1eCPUzMv0wD0fqhyq
 piAbOpKLO6v1k/p4veTCa8gEimpp1Ni4QKqeLxkZ54hrt+uvrQbb7HxqfXuGwNG4
 IWnkfocZXN6nUbjNh7NitGgRZCMtiKJSgXrwlmluXoi0OyUNwxX7Fbn9JqsbWpMR
 lqFVJxbJ4jGozWK5wb5jcT5PArVkYgr+FN7lmqefysEltBjpv0JWqdxKH44RteyA
 wA4yPz/5Oe/iZJu9h2GzHuFHma2Dr8z43NrsIO/cTKN5uG9gzbKbp8IxV2P715OZ
 R5XPzSHLFD1Q/A855yKxvF1tlizSDdKo2pXZ2BfvLBZEljd37QmVkRSy+gPL3QhD
 bMICPJ1opuJZb9dEi0L54yk9+tm4ImWTuYRNOsFc4p9EGT4P9yydqMkpzuuHXRJb
 GcLoD+TXgoxK8PijX9QWdQPnb0FkFKShwWMXOn9zyzIDIzT4HlZN8HtyPCYmbyD1
 6uFWiQQEfvbzInPmQpgk5mZoblskMSI/pN+4KHKlH3X4yWK5YGQ=
 =zrJm
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-amlogic-20210727' of https://source.denx.de/u-boot/custodians/u-boot-amlogic

- Add SMBIOS info for Khadas VIM boards
- Fix meson-axg-mipi PHY build
- Fix VIM3 board phy-names property setup
- Return correct value for non emmc boot sources on VIM3
- add kernel compression vars
2021-07-27 11:42:31 -04:00
Artem Lapkin
e10481be1e ARM: dts: meson: Use devicetree for SMBIOS settings for Khadas VIM boards
Khadas vim series: Use devicetree for SMBIOS settings
Add settings and enable the default sysinfo driver so that these can come
from the device tree.

Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Artem Lapkin <art@khadas.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2021-07-27 10:32:59 +02:00
Alexandru Gagniuc
65b3f56d42 ARM: dts: stm32mp: Add OP-TEE reserved memory to SPL dtb
Add the "/reserved-memory/optee" node to the SPL devicetree. The
purpose is to allow configuring TZC regions when booting OP-TEE.

Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2021-07-27 09:48:11 +02:00
Marek Vasut
59000ebe0b ARM: dts: stm32: Fix AV96 eMMC pinmux
Commit 500327e2ea ("ARM: dts: stm32mp1: DT alignment with Linux kernel v5.8-rc1")
renamed sdmmc2_d47_pins_b phandle to sdmmc2_d47_pins_c, but without updating
the AV96 DT which uses that phandle. Linux missed similar update as well and
it was only added in commit 1ad6e36ec266 ("ARM: dts: stm32: Fix sdmmc2 pins
on AV96") .

Update the AV96 DT pinmux phandle, otherwise eMMC 8bit mode does not work
and access to eMMC takes a very long time to fall back to 4bit mode.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
2021-07-27 09:47:40 +02:00
Patrick Delaunay
2a7034c77d stm32mp1: add pull-up for gpio button PA13 and PA14
When a push-button is released and PA13/PA14 are defined as input (high-Z)
the LED should not be active as the circuit is open but a small current
leak through PCB or push-button close the circuit and allows a small LED
bias giving erroneous level voltage.

So it is recommended to activate an internal pull-up in order to clearly
fix the voltage at PA13/PA14 when button is released and to wait
a short delay before to read the GPIO value only when the pull-up is
correctly configured.

Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
2021-07-27 09:47:40 +02:00
Suman Anna
24f3fb6547 arm: dts: k3-j721e-r5: Remove MAIN R5FSS0 cluster from SPL
The MAIN R5FSS0 cluster and corresponding nodes are no longer required
to be enabled in R5 SPL after removing the support for booting any core
from this cluster on R5 SPL. So, remove these from the relevant dts
files.

This is essentially a revert of the additions done in commit 2984b82b3b
("arm: dts: k3-j721e-r5: Enable r5fss0 cluster in SPL").

Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210726211311.5977-5-s-anna@ti.com
2021-07-27 11:00:44 +05:30
Suman Anna
31b3d7a018 arm: dts: k3-am65: Fix up MCU R5FSS cluster mode back to Split-mode
The default U-Boot environment variables and design are all set up to
have the MCU R5FSS cluster to be in Split-mode. This is the setting
in v2021.01 U-Boot and the dt nodes are synched with the kernel binding
property names in commit 468ec2f3ef ("remoteproc: k3_r5: Sync to
upstreamed kernel DT property names") merged in v2021.04-rc2.

The mode for the cluster got switched back to LockStep mode by mistake
in commit e497876343 ("arm: dts: k3-am65: Sync Linux v5.11-rc6 dts
into U-Boot") also in v2021.04-rc2. This throws the following warning
messages when early-booting the cores using default env variables,

  k3_r5f_rproc r5f@41400000: Invalid op: Trying to start secondary core 2 in lockstep mode
  Load Remote Processor 1 with data@addr=0x82000000 65268 bytes: Failed!

Fix this by switching back the cluster to the expected Split-mode.
Make this mode change in the u-boot specific dtsi file to avoid such
sync overrides in the future until the kernel dts is also switched to
Split-mode by default.

Fixes: e497876343 ("arm: dts: k3-am65: Sync Linux v5.11-rc6 dts into U-Boot")
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210726162213.28719-1-s-anna@ti.com
2021-07-27 11:00:10 +05:30
Aswath Govindraju
0817dd5432 arch: dts: am642-sk-u-boot: Disable main_sdhci0 DT node and define alias index 1 for main_sdhci1 node
A Wilink wireless device is connected to MMCSD0 subsystem and is not
supported in U-Boot. Therefore, disable main_sdhci0 device tree node in
U-Boot.

If main_sdhci0 device tree node is disabled then the the index of
main_sdhci1 node becomes 0 which leads to break in boot flow. Therefore,
add an alias to fix the index to 1.

Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210726152807.22991-3-a-govindraju@ti.com
2021-07-27 10:58:49 +05:30
Aswath Govindraju
08189ffd15 arm: dts: k3-j7200-common-proc-board-u-boot: Add u-boot tags for torrent serdes
Add u-boot tags for torrent serdes. This has properties specific to
u-boot on top of DT in v5.13 Linux Kernel.

Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210721155849.20994-15-kishon@ti.com
2021-07-27 10:57:12 +05:30
Aswath Govindraju
cbea79867e arm: dts: k3-j7200-common-proc-board: Enable SERDES DT
Add default lane function for torrent serdes. This is in sync
with v5.13 Linux Kernel.

Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210721155849.20994-14-kishon@ti.com
2021-07-27 10:57:12 +05:30
Aswath Govindraju
6c4be8eb7e arm: dts: k3-j7200-main: Add DT node for torrent serdes
Add DT node for torrent serdes. This is in sync with v5.13 Linux Kernel.

Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210721155849.20994-13-kishon@ti.com
2021-07-27 10:57:12 +05:30
Kishon Vijay Abraham I
ad256cc894 ARM: dts: k3-j721e: Add support for USB3 in USB0 instance
Configure the parent clock of wiz3_pll0_refclk to the internal clock
required for USB3 to be functional and also remove "ti,usb2-only"
property as it now supports USB3 mode. This has properties specific to
u-boot on top of DT present in v5.13 of Linux Kernel.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210721155849.20994-12-kishon@ti.com
2021-07-27 10:57:12 +05:30
Paul Barker
124b3030f5 arm: dts: Import am335x-sancloud-bbe devicetree
This device tree is imported from Linux 5.13.1 and enabled via the
am335x board file and the am335x evm defconfig.

Signed-off-by: Paul Barker <paul.barker@sancloud.com>
2021-07-27 10:56:09 +05:30
Paul Barker
942853dd96 arm: dts: Resync BeagleBone device trees
These device trees are updated to match the versions in Linux 5.13.1.
The tick-timer entry in am335x-bone-common.dtsi is preserved.

Signed-off-by: Paul Barker <paul.barker@sancloud.com>
2021-07-27 10:56:09 +05:30
Aswath Govindraju
455f9dddc8 arm: dts: k3-j7200-main: Add support for HS400 and update delay select values for MMCSD subsystems
HS400 speed mode is now supported in J7200 SoC[1]. Therefore add
mmc-hs400-1_8v tag in sdhci0 device tree node.

Also update the delay values for various speed modes supported, based on
the revised january 2021 J7200 datasheet[2].

[1] - section 12.3.6.1.1 MMCSD Features, in
      https://www.ti.com/lit/ug/spruiu1a/spruiu1a.pdf,
      (SPRUIU1A – JULY 2020 – REVISED JANUARY 2021)

[2] - https://www.ti.com/lit/ds/symlink/dra821u.pdf,
      (SPRSP57B – APRIL 2020 – REVISED JANUARY 2021)

Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210525093826.10390-3-a-govindraju@ti.com
2021-07-27 10:56:09 +05:30
Simon Glass
5e19f4aa13 samsung: exynos: Convert SROMC interface to a driver
Add a bus driver for this and use it to configure the bus parameters for
the Ethernet interface. Drop the old pre-driver-model code.

Switch over to use driver model for Ethernet.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2021-07-27 10:34:27 +09:00
Manish Narani
15ca9ebb07 arm64: zynqmp: Move USB3 PHY properties from DWC3 node to USB node
Move the PHY properties from DWC3 node to USB node in ZynqMP DTs as here
the USB3 PHY used is PSGTR, which is connected to Xilinx USB core. This
PHY initialization should be handled from Xilinx USB core as the
prerequisite register configurations are done here only.

Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-07-26 09:26:41 +02:00
Piyush Mehta
d036f4f2c6 arm64: dts: zynqmp: Enable USB2.0 for zc1751-xm016-dc2
The board zynqmp-zc1751-xm016-dc2 support only USB2.0.
This patch removes USB3.0 DT configuration for DC2 board.

Signed-off-by: Piyush Mehta <piyush.mehta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-07-26 09:18:45 +02:00
Masami Hiramatsu
11cd1d6a34 dts: synquacer: Add partition information to the spi-nor
Add partition information to the spi-nor flash.
This is required for accessing NOR flash via mtdparts.

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
2021-07-23 18:53:45 -04:00
Tom Rini
806734f41b Merge https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriq
fsl-qoriq: Update mc firmware size, address in LS1088A, LS2088A, LX2
Updates on ls1043aqds, ls1043ardb
Refactor I2C MUX Code on fsl-qoriq platforms.
2021-07-22 08:45:32 -04:00
Marek Vasut
3d5f45c95c ARM: dts: rmobile: Disable RPC HF by default
The RPC HF might be locked by ATF, and any access to its register
space would result in complete hang. Disable the RPC HF by default.
The ATF should be patched to set RPC node status = "okay" in the DT
fragment it passes to U-Boot in case the RPC HF access is unlocked,
and that way U-Boot could access the RPC HF safely.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
2021-07-20 23:33:54 +02:00
Marek Vasut
778fbe2668 ARM: dts: rmobile: Add sysinfo extras on R-Car Gen3
Add sysinfo node and phandle to the board ID EEPROM on all boards
where this functionality is described in DT, which is Salvator-X(S),
ULCB and Ebisu. The u-boot,dm-pre-reloc is necessary here, since the
sysinfo must be available early during boot. The V3M and V3H boards
currently do not describe this board ID EEPROM in upstream DT, but
that could be easily added later, once the DTs contain the necessary
nodes.

ULCB and Ebisu needs the full EEPROM node in the u-boot extras DT,
since the EEPROM node is still missing in the upstream DTs. Ebisu
also needs extra compatible string override for the i2c_dvfs.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
2021-07-20 23:33:54 +02:00
Camelia Groza
af956271f6 arm: dts: ls1043ardb: configure the RGMII ports with rgmii-id
The RGMII ports on LS1043ARDB platforms require both RX and TX internal
delays to be enabled. The device tree reports only the TX ID because the
RX ID used to be enabled by default.

With the addition of RX ID support for the Realtek 8211F PHY driver in
commit e32e4d0f58 ("net: phy: realtek: add rx delay support for
RTL8211F"), the RX ID is disabled by the driver if not reported explicitly.
This causes the RX to no longer work.

Change the phy-connection-type for the RGMII ports to "rgmii-id" in order
to enable both RX and TX internal delays.

Fixes: be1d758969 ("ARM: dts: add QorIQ DPAA 1 FMan v3 to LS1043ARDB")
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-07-20 14:53:43 +05:30
Tom Rini
dd3dfa50d8 Merge https://source.denx.de/u-boot/custodians/u-boot-marvell
- Marvell SheevaPlug: Convert Ethernet and SATA to Driver Model (Tony)
- Zyxel NSA310S NAS: Convert to Driver Model (Tony)
- Turris_omnia: Add `u-boot-env` NOR partition (Marek)
- Turris_omnia: Fixup MTD partitions in Linux' DTB (Marek)
- Espressobin: Enable 'mtd' command and define SPI NOR partitions (Pali)
2021-07-19 08:41:04 -04:00
Tom Rini
83befb4466 Merge tag 'ti-v2021.10-rc1' of https://source.denx.de/u-boot/custodians/u-boot-ti
- Enabled distro boot for all TI platforms.
- Cleanup for AM335x Guardian Board
- PRUSS rproc on AM65 platform.
- Add PMIC support for J7200
- Misc fixes for Nokia RX-51

# Conflicts:
#	arch/arm/mach-omap2/am33xx/Kconfig
2021-07-19 08:29:24 -04:00
Pali Rohár
a675eb14bd arm: mvebu: Espressobin: Enable 'mtd' command and define SPI NOR partitions
U-Boot now supports parsing SPI NOR partitions from Device Tree. So enable
'mtd' command support for Espressobin board and define partition layout in
U-Boot Espressobin DTS file. Access to SPI NOR via 'sf' command is old
method and 'mtd' command is now preferred variant.

From include file remove '#define CONFIG_MTD_PARTITIONS' as this option is
now defined and enabled in defconfig file. This change is required to fix
compile error:

      CC      arch/arm/lib/asm-offsets.s
    In file included from include/config.h:4,
                     from include/common.h:16,
                     from lib/asm-offsets.c:14:
    include/configs/mvebu_armada-37xx.h:63: warning: "CONFIG_MTD_PARTITIONS" redefined
     #define CONFIG_MTD_PARTITIONS  /* required for UBI partition support */

    In file included from ././include/linux/kconfig.h:4,
                     from <command-line>:
    include/generated/autoconf.h:44: note: this is the location of the previous definition
     #define CONFIG_MTD_PARTITIONS 1

After enabling support for mtd command, output from 'mtd list' on
Espressobin board is:

    => mtd list
    List of MTD devices:
    * w25q32dw
      - device: spi-flash@0
      - parent: spi@10600
      - driver: jedec_spi_nor
      - path: /soc/internal-regs/spi@10600/spi-flash@0
      - type: NOR flash
      - block size: 0x1000 bytes
      - min I/O: 0x1 bytes
      - 0x000000000000-0x000000400000 : "w25q32dw"
              - 0x000000000000-0x0000003f0000 : "firmware"
              - 0x0000003f0000-0x000000400000 : "u-boot-env"
    =>

Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2021-07-19 09:05:30 +02:00
Marek Behún
644b986470 ARM: dts: armada-385-turris-omnia: add u-boot-env NOR partition
Specify a separate partition `u-boot-env` for U-Boot's env settings for
the Turris Omnia board.

Do this only in U-Boot's specific DTS. We do not want to do this in
Linux' official DTS, because Omnia's stock U-Boot stores env at a
different address, and there are still boards with stock U-Boot.

In a subsequent patch will add board code that fixes Linux's DTB before
booting Linux.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
2021-07-19 09:05:30 +02:00
Tony Dinh
ee48f53722 arm: kirkwood: NSA310S: Add device tree DTS for Zyxel NSA310S board
Add device tree kirkwood-nsa310s.dts for Zyxel NSA310S board to
convert to Driver Model.

Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2021-07-19 08:44:02 +02:00
Tom Rini
d5dbc661c3 i.MX
----
 
 - mx7ulp : fix  WDOG
 - imx8 : Phytec
 - USB3 support for i.MX8
 
 CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/8277
 -----BEGIN PGP SIGNATURE-----
 
 iG0EABECAC0WIQS2TmnA27QKhpKSZe309WXkmmjvpgUCYPLjyA8cc2JhYmljQGRl
 bnguZGUACgkQ9PVl5Jpo76aBtgCfUI2SbFwh7oydllrwb0lEvWegfNcAn1JpR3Zn
 H41xrXQqCBedYKxvuUUL
 =5wvR
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-imx-20210717' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx

i.MX
----

- mx7ulp : fix  WDOG
- imx8 : Phytec
- USB3 support for i.MX8

CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/8277
2021-07-17 10:52:21 -04:00
Ye Li
4390e9f997 arm: dts: imx8mq: Add alias for two usb controllers
Add alias for two DWC3 usb controllers to fix the seq index.

Signed-off-by: Ye Li <ye.li@nxp.com>
Tested-by: Patrick Wildt <patrick@blueri.se>
2021-07-17 13:12:23 +02:00
Patrick Delaunay
db1ab52e15 ARM: dts: stm32mp15: remove mmc alias
Remove the mmc alias no more required as the sequence number
of mmc device is used for boot_instance.

Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
2021-07-16 09:28:46 +02:00
Patrick Delaunay
7e54934532 arm: dts: stm32mp15: alignment with v5.13
Device tree alignment with Linux kernel v5.13
- ARM: dts: stm32: Add PTP clock to Ethernet controller
- ARM: dts: stm32: enable the analog filter for all I2C nodes in
  stm32mp151
- ARM: dts: stm32: fix usart 2 & 3 pinconf to wake up with flow control
- ARM: dts: stm32: Add wakeup management on stm32mp15x UART nodes
- ARM: dts: stm32: add #clock-cells property to usbphyc node on stm32mp151
- ARM: dts: stm32: Add STM32MP1 I2C6 SDA/SCL pinmux
- ARM: dts: stm32: Rename mmc controller nodes to mmc@
- ARM: dts: stm32: Add additional init state for SDMMC1 pins

Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
2021-07-16 09:28:46 +02:00
Gowtham Tammana
2094e70692 arm/dts: k3-j7200-r5-common: Hook buck1_reg to vtm supply
Hook buck1_reg to vtm avs supply.

Signed-off-by: Gowtham Tammana <g-tammana@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210714205300.17424-5-g-tammana@ti.com
2021-07-15 17:56:04 +05:30
Gowtham Tammana
fcdf03aab9 arm/dts: k3-j7200-r5-common: Add VTM node
Add voltage and thermal management (VTM) node. The efuse values for the
OPPs are stored under the VTM, and is needed for AVS class 0 support.

Signed-off-by: Gowtham Tammana <g-tammana@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210714205300.17424-4-g-tammana@ti.com
2021-07-15 17:56:04 +05:30
Gowtham Tammana
6fb8706bcb arm/dts: k3-j7200-r5-common: Add pmic lp876441 node
Add pmic lp876411 node needed for CPU AVS support.

Signed-off-by: Gowtham Tammana <g-tammana@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210714205300.17424-3-g-tammana@ti.com
2021-07-15 17:56:04 +05:30
Lokesh Vutla
c81e7f8d17 arm: dts: ti: k3-am65-main: Add ICSSG nodes
Add the DT nodes for the ICSSG0, ICSSG1 and ICSSG2 processor subsystems
that are present on the K3 AM65x SoCs. The three ICSSGs are identical
to each other for the most part, with the ICSSG2 supporting slightly
enhanced features for supporting SGMII PRU Ethernet. Each ICSSG instance
is represented by a PRUSS subsystem node. These nodes are enabled by
default.

DT nodes are fetch from Linux 5.13 Kernel.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210622063431.3151-5-lokeshvutla@ti.com
2021-07-15 17:56:04 +05:30
Lokesh Vutla
654b60a8fd arm: dts: k3-am654-base-board: Add r5 specific u-boot dtsi
So far all the u-boot specific properties for both r5 and a53 are
placed in k3-am654-base-board-u-boot.dtsi. But there are few a53
nodes that should be updated but doesn't belong to r5. So create a
separate r5 specific u-boot dtsi.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210622063431.3151-4-lokeshvutla@ti.com
2021-07-15 17:56:04 +05:30
Aswath Govindraju
776e25788c arm: dts: k3-am64-main: Reserve OCMRAM for DMSC-lite and secure proxy communication
The final 128KB in SRAM is reserved by default for DMSC-lite code and
secure proxy communication buffer. The memory region used for DMSC-lite
code can be optionally freed up by secure firmware API[1]. However, the
buffer for secure proxy communication is not configurable. This default
hardware configuration is unique for AM64.

Therefore, indicate the area reserved for DMSC-lite code and secure proxy
communication buffer in the oc_sram device tree node.

[1] - http://downloads.ti.com/tisci/esd/latest/6_topic_user_guides/security_handover.html#triggering-security-handover

Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20210616163821.20457-3-a-govindraju@ti.com
2021-07-15 17:56:04 +05:30
Aswath Govindraju
5242c6a432 configs: am64x_evm_a53_defconfig: Move TF-A load address to 0x701c0000
Earlier, the region 0x701c0000 to 0x701dffff was firewalled off because of
a bug in SYSFW. In the v2021.05 release of SYSFW this bug has been fixed
and this region can now be used for other allocations.

Therefore, move TF-A's load address to 0x701c0000 and update its location
in the device tree node. Also, increase the size allocated for TF-A to
account for future expansions.

Fixes: defd62ca13 ("arm: dts: k3-am64-main: Update the location of ATF in SRAM and increase its max size")
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20210616163821.20457-2-a-govindraju@ti.com
2021-07-15 17:56:04 +05:30
Gireesh Hiremath
9cd380ef5f am335x, guardian: Enable panel driver Himax HX8238D
- Enable lcd controller
- Display splash screen

Signed-off-by: Gireesh Hiremath <Gireesh.Hiremath@in.bosch.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210611161350.2141-16-Gireesh.Hiremath@in.bosch.com
2021-07-15 17:56:03 +05:30
Moses Christopher
cea76a4f42 am335x, guardian: Update pinmux configuration
pinmux update for guardian board
- control ASP Board Power: GPIO, on/off ASP Board Power
- control Coincell Voltage Measurement: GPIO, enable/disable
  ADC measurements
- powerOff Device GPIO-PowerOff, cut the PMIC supply

Signed-off-by: Moses Christopher <BollavarapuMoses.Christopher@in.bosch.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210611161350.2141-7-Gireesh.Hiremath@in.bosch.com
2021-07-15 17:56:03 +05:30
Kunihiko Hayashi
9e9074bcdd ARM: dts: uniphier: Add support for Akebi96
Add the device tree for Akebi96. Akebi96 is a 96boards certified
development board based on UniPhier LD20.
( https://www.96boards.org/product/akebi96/ )

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
2021-07-14 16:48:10 -04:00
Tim Harvey
1cb87b929e arm: dts: imx8mm-venice-gw7901.dts: fix dsa switch configuration
Fix the dsa switch config:
- remove the unnecessary phy-mode from the switch itself
- added the necessary fixed-link node to the non-cpu ports required
  for U-Boot DSA

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-07-10 18:12:42 +02:00
Tim Harvey
c9f7ef37f9 board: gateworks: venice: add imx8mm-gw7901 support
The Gateworks GW7901 is an ARM based single board computer (SBC)
featuring:
 - i.MX8M Mini SoC
 - LPDDR4 DRAM
 - eMMC FLASH
 - SPI FRAM
 - Gateworks System Controller (GSC)
 - Atmel ATECC Crypto Authentication
 - USB 2.0
 - Microchip GbE Switch
 - Multiple multi-protocol RS232/RS485/RS422 Serial ports
 - onboard 802.11ac WiFi / BT
 - microSD socket
 - miniPCIe socket with PCIe, USB 2.0 and dual SIM sockets
 - Wide range DC power input
 - 802.3at PoE

To add support for this board:
 - add dts from Linux (accepted for v5.14)
 - add SPL PMIC config

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-07-10 18:12:41 +02:00
Teresa Remmet
f11e3dafb3 arm: dts: imx8mp-phyboard-pollux-rdk-u-boot: Add wdog pinctrl entry
Add missing pinctrl entry in spl.

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
2021-07-10 16:53:34 +02:00
Teresa Remmet
1feac813fe board: phytec: phycore_imx8mp: Change debug UART
With the first redesign the debug UART had changed from
UART2 to UART1.
As the first hardware revision is considered as alpha and
will not be supported in future. The old setup will not
be preserved.

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
2021-07-10 16:53:34 +02:00
Teresa Remmet
3240d9c63a arm: dts: imx8mp-phyboard-pollux: Sync dts files with kernel
This update includes eqos support and some minor changes.

Synced with kernel commit
412627f6ffe3 ("arm64: dts: imx8mp-phyboard-pollux-rdk: Add missing pinctrl entry")

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
2021-07-10 16:53:34 +02:00
Teresa Remmet
dafb164f61 arm: dts: imx8mp: Add common u-boot dtsi
Factor out the common node settings for dm-spl and dm-pre-reloc
and move them to imx8mp-u-boot.dtsi

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
2021-07-10 16:53:34 +02:00
Teresa Remmet
6bd1db0a0c arm: dts: imx8mp: Resync imx8mp device tree include
Sync imx8mp include with kernel commit:
d1689cd3c0f4 ("arm64: dts: imx8mp: Use the correct name for child node "snps, dwc3"")

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
2021-07-10 16:53:34 +02:00
Yu-Tung Chang
2527b24f39 sunxi: h3: Add initial ZeroPi support
ZeroPi is a new board of high performance with low cost
designed by FriendlyElec., using the Allwinner H3 SOC.

ZeroPi features
- Allwinner H3, Quad-core Cortex-A7@1.2GHz
- 256MB/512MB DDR3 RAM
- microsd slot
- 10/100/1000Mbps Ethernet
- Debug Serial Port
- DC 5V/2A power-supply

Signed-off-by: Yu-Tung Chang <mtwget@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-07-10 01:22:09 +01:00
Andre Przywara
8fcf1fa246 arm: dts: sunxi: h3: Update DT files
Update the H3 DT files from the Linux 5.12 release.

The changes update some boards, and don't affect U-Boot, but fix Gigabit
Ethernet when this DT is passed on to the Linux kernel.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-07-10 01:22:09 +01:00
Andre Przywara
58f68611df arm: dts: sunxi: h5: Update DT files
Update the H5 DT files from the Linux 5.12 release.

The changes don't affect U-Boot at all, but fix Gigabit Ethernet when
this DT is passed on to the Linux kernel. It also introduces DVFS.

This also updates the shared sunxi-h3-h5.dtsi, but that only adds nodes
that are of no concern to U-Boot.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-07-10 01:22:09 +01:00
Andre Przywara
127e57c671 arm: dts: sunxi: h6: Update DT files
Update the H6 DT files from the Linux 5.12 release.

The changes are minimal (many LED node renames), but also help to enable
USB port 0 in U-Boot (later), enable the RSB device (not yet used in
U-Boot), and also introduce an MMC frequency limit.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-07-10 01:22:09 +01:00
Tom Rini
008604c3b8 First set of u-boot-atmel fixes for 2021.10 cycle
-----BEGIN PGP SIGNATURE-----
 
 iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmDkSkAcHGV1Z2VuLmhy
 aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyD24B/9t87hFqWovJvVAcoUT
 JoTqFblplE4Sckssy0cQyR7sRpzuZEaakUeAxaLFecBN6Tn30YJEG3hNpEDCLEbA
 hn/oiZ4hQ3JA9Yu2SHepQi0fLqdAjkQtMXy57o3Mk20GBLtPtpdItUHxg3iyeMSj
 Ny1mm/KjL6ltmNeGfYfeqRf435Rm718DB94wCZTgS9woYe3Z5YRDNBPyL7u27hpY
 2WiyvvU9EA12mjGYdEt5sCqnTQZFtHHlEWNHz4a3db6HkcPV7pfr+SpTNJjcFhIg
 O7VN7yUTwnV0UGu5IXTWcZqFIqJkLPbPX5cvkSBnnaGge4e0K3Cw36Nv/EqCY8LX
 gWfu
 =Ru8k
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-atmel-fixes-2021.10-a' of https://source.denx.de/u-boot/custodians/u-boot-atmel

First set of u-boot-atmel fixes for 2021.10 cycle:

This small fixes set is dedicated to fixing the onewire subsystem for
the at91 boards which was broken since 2020.04.
2021-07-07 08:52:14 -04:00
Tom Rini
5617efd2c8 Merge branch '2021-07-06-platform-updates'
- mpc8379erdb DM_USB, DM_PCI and DM_ETH support.
- Drop PCI support from the integrator family of boards
- Add synquacer support
- Assorted lpc32xx updates and improvements
- snapdragon (and related) fixes, Broadcom iproc update
2021-07-06 18:10:10 -04:00
Stephan Gerhold
698c1df4d1 arm: dts: db410c: Add missing cd-gpios for SD card detection
It looks like SD card detection is broken at the moment for DB410c.
The eMMC is detected correctly, but the SD card is not.

This is probably similar to the issue fixed in commit 8505147403
("mmc: msm_sdhci: Use mmc_of_parse for setting host_caps") for eMMC,
except that the SD card does not have a property like "non-removable"
that skips the card detection.

The SDHCI on DB410c cannot detect itself if a SD card is inserted,
so add the necessary cd-gpios to make SD card detection work again.

While at it, fix the #gpio-cells for the soc_gpios to avoid DTC
warnings - the soc_gpios are actually already used with two cells
for the gpio-leds so this was just wrong all the time.

Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
2021-07-06 14:12:15 -04:00
Trevor Woerner
faf78fd464 arm: lpc32xx: add EA LPC3250 DevKitv2 board support
Add basic support for running U-Boot on the Embedded Artists LPC3250
Developer's Kit v2 board by launching U-Boot from the board's s1l loader
(which comes pre-installed on the board).

Signed-off-by: Trevor Woerner <twoerner@gmail.com>
2021-07-06 14:12:14 -04:00
Trevor Woerner
eb5807e68f lpc32xx: import device tree from Linux
Import the dtsi, dts, and clock binding files for the lpc32xx ea3250 board
directly and unmodified from the latest Linux kernel.

Signed-off-by: Trevor Woerner <twoerner@gmail.com>
2021-07-06 14:11:50 -04:00
Masami Hiramatsu
2f1f797efa ARM: dts: synquacer: Add device trees for DeveloperBox
Add device trees for 96boards EE DeveloperBox and basement SynQuacer
SoC dtsi. These files are imported from EDK2

commit 83d38b0b4c0f240d4488c600bbe87cea391f3922

as-is (except for the changes #include path and some macros).

And add U-Boot specific changes in synquacer-sc2a11-developerbox-u-boot.dtsi

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
2021-07-06 14:11:49 -04:00
Eugen Hristev
89bd68a748 ARM: dts: at91: fix the GPIO polarity for onewire
The GPIO polarity for onewire must be GPIO_ACTIVE_HIGH.
On previous versions this used to work as it looks like the right flag values
are being passed since :
https://lists.denx.de/pipermail/u-boot/2020-April/407195.html

And that series broke the old functionality for onewire nodes.
Some boards had the correct value for the polarity, but it wasn't clear
so I replaced it with the right macro for the flag, instead of an empty value.

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2021-07-06 15:17:10 +03:00
Michael Walle
515ed9df24 board: sl28: add DSA support for variant 2
Now that u-boot gained DSA support, and it is already enabled for the
kontron_sl28 board, add the last missing piece and enable the
corresponding devices it in the device tree.

Signed-off-by: Michael Walle <michael@walle.cc>
2021-07-06 05:22:41 +03:00
Vladimir Oltean
bec7d5342d arm: dts: ls1028a: disable enetc-2 by default
The enetc-2 port is used as DSA master (connected back-to-back to
mscc_felix_port4). Since the convention is to not enable ports in the
common SoC dtsi unless they are used on the board, then enable enetc-2
only when mscc_felix_port4 itself is enabled.

All existing device trees appear to adhere to this rule, so disable
enetc-2 in the SoC dtsi.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
2021-07-06 05:22:41 +03:00
Vladimir Oltean
9feb636680 arm: dts: ls1028a: declare the fixed-link speeds for the internal ENETC ports
To comply with the device tree bindings expectations for an Ethernet
controller, as well as to simplify the driver code, declare fixed-link
nodes for the internal ENETC ports (attached to the mscc_felix switch).

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
2021-07-06 05:22:41 +03:00
Vladimir Oltean
aee4479a85 arm: dts: ls1028a: enable internal RGMII delays for the LS1028A-QDS AR8035 PHY
There are no PCB trace delays on this board, so the PHY needs to enable
its internal ones in order to have a proper electrical connection to the
enetc MAC.

Fixes: b32e9a7578 ("arm: dts: ls1028a updates for network interfaces")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
2021-07-06 05:22:41 +03:00
Vladimir Oltean
39dca76c34 arm: dts: ls1028a: enable the switch CPU port for the LS1028A-QDS
Due to an upstream change, the ls1028a.dtsi bindings for the mscc_felix
switch got accepted with all ports disabled by default and with no link
to the DSA master - this needs to be done on a per board basis.

Note that enetc-2 is not currently disabled in the ls1028a.dtsi, but
presumably at some point it might become. Explicitly enable it in the
QDS device trees anyway, to proactively avoid issues when that happens.

Fixes: a7fdac7e2a ("arm: dts: ls1028a: define QDS networking protocol combinations")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
2021-07-06 05:22:41 +03:00
Tom Rini
6b69f15fd6 Xilinx changes for v2021.10
clk:
 - Add driver for Xilinx Clocking Wizard IP
 
 fdt:
 - Also record architecture in /fit-images
 
 net:
 - Fix plat/priv data handling in axi emac
 - Add support for 10G/25G speeds
 
 pca953x:
 - Add missing dependency on i2c
 
 serial:
 - Fix dependencies for DEBUG uart for pl010/pl011
 - Add setconfig option for cadence serial driver
 
 watchdog:
 - Add cadence wdt expire now function
 
 zynq:
 - Update DT bindings to reflect the latest state and descriptions
 
 zynqmp:
 - Update DT bindings to reflect the latest state and descriptions
 - SPL: Add support for ECC DRAM initialization
 - Fix R5 core 1 handling logic
 - Enable firmware driver for mini configurations
 - Enable secure boot, regulators, wdt
 - Add support xck devices and 67dr
 - Add psu init for sm/smk-k26 SOMs
 - Add handling for MMC seq number via mmc_get_env_dev()
 - Handle reserved memory locations
 - Add support for u-boot.itb generation for secure OS
 - Handle BL32 handoffs for secure OS
 - Add support for 64bit addresses for u-boot.its generation
 - Change eeprom handling via nvmem aliases
 -----BEGIN PGP SIGNATURE-----
 
 iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYN105QAKCRDKSWXLKUoM
 IZiFAJ9CIiEpHiBbnAhA0VOMGoaXHGULywCdED/5dNgVtc1C7y4avzETbEyWzD4=
 =CdMa
 -----END PGP SIGNATURE-----

Merge tag 'xilinx-for-v2021.10' of https://source.denx.de/u-boot/custodians/u-boot-microblaze into next

Xilinx changes for v2021.10

clk:
- Add driver for Xilinx Clocking Wizard IP

fdt:
- Also record architecture in /fit-images

net:
- Fix plat/priv data handling in axi emac
- Add support for 10G/25G speeds

pca953x:
- Add missing dependency on i2c

serial:
- Fix dependencies for DEBUG uart for pl010/pl011
- Add setconfig option for cadence serial driver

watchdog:
- Add cadence wdt expire now function

zynq:
- Update DT bindings to reflect the latest state and descriptions

zynqmp:
- Update DT bindings to reflect the latest state and descriptions
- SPL: Add support for ECC DRAM initialization
- Fix R5 core 1 handling logic
- Enable firmware driver for mini configurations
- Enable secure boot, regulators, wdt
- Add support xck devices and 67dr
- Add psu init for sm/smk-k26 SOMs
- Add handling for MMC seq number via mmc_get_env_dev()
- Handle reserved memory locations
- Add support for u-boot.itb generation for secure OS
- Handle BL32 handoffs for secure OS
- Add support for 64bit addresses for u-boot.its generation
- Change eeprom handling via nvmem aliases
2021-07-01 08:57:23 -04:00
Tom Rini
8fba49bc8e Merge branch 'next' of https://source.denx.de/u-boot/custodians/u-boot-sh into next
- V3U Falcon board support
2021-06-28 18:32:07 -04:00
Tom Rini
6d0453d889 Prepare v2021.07-rc5
-----BEGIN PGP SIGNATURE-----
 
 iQGzBAABCgAdFiEEGjx/cOCPqxcHgJu/FHw5/5Y0tywFAmDaJXgACgkQFHw5/5Y0
 tyySmwwAkW7GVAv+bXSd+8u1IsScl0QrSCoBdfHpdMcAME3gZmXqxClxskfbYJR/
 3IByQFlsn7j8HruR/49+etk0i0Pc4HNfynTLuAy+77/lh+h3Pnru/VPBhQqR7KW0
 NN5STn91QWLl74vRmx5wmEfSMhg7LTE1US8Rh6UXAd2dAiPd+hUawIR9D0Pq5Gzm
 nn7HvamDYspFUgSYYl8h1RtRQ9VqAFpnnPphpLkvX6323uCQwccXu5pnj1fLfGfj
 iO2Q+bDcwpEdUosox/LM1BdMoaSA+opOjk/e72y9V84+Jk6D+Jn5zQEpF5TJnTyI
 Yi2+NuJWS5xFWk1dnJrbGt0HpWM2oO12dZZ7eYy/FdsPJiWAS0ppRuxHVb868vjD
 ulca7acFPUjGyo3vBw1S0iVmPCBFGHBoyg3QLrUHYbpISeBeoa2w2cDxQl90ahw/
 TgRx+yutKfwkBPfILwDylNOgCGRwvLfroRyMEMiQ3gTSOCBmBX/yMv1k8tb9ZvPZ
 /WVsK6dw
 =F7x1
 -----END PGP SIGNATURE-----

Merge tag 'v2021.07-rc5' into next

Prepare v2021.07-rc5

# gpg: Signature made Mon 28 Jun 2021 03:39:36 PM EDT
# gpg:                using RSA key 1A3C7F70E08FAB1707809BBF147C39FF9634B72C
# gpg: Good signature from "Thomas Rini <trini@konsulko.com>" [ultimate]

# Conflicts:
#	configs/am64x_evm_r5_defconfig
2021-06-28 16:22:13 -04:00
Piyush Mehta
436978b1d8 arm64: dts: zynqmp: Add psgtr and phy entry for USB and SATA node
This patch adds psgtr clocks and phy entry for USB0, USB1 and SATA node for
zc1751-xm017-dc3 board.

Signed-off-by: Piyush Mehta <piyush.mehta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-06-28 09:35:27 +02:00
Hai Pham
4cfdcf3948 ARM: renesas: Add R8A779A0 V3U Falcon board code
Add board code for the R8A779A0 V3U Falcon board.

Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
--
Marek: - various small rebase fixes and clean ups
2021-06-24 20:22:18 +02:00
Marek Vasut
ae3c0d42fa ARM: dts: renesas: Add RPC node to R8A779A0 V3U
The R-Car V3U does support RPC interface, however the support for it is
missing in upstream Linux DTs as of commit 9f4ad9e425a1 ("Linux 5.12"),
add the node into u-boot.dtsi to let U-Boot access the SPI NOR or HF.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
2021-06-24 20:22:18 +02:00
Hai Pham
b35fc0dabd ARM: dts: renesas: Add R8A779A0 V3U DT extras
Add R8A779A0 V3U DT extras for U-Boot.

Based on "ARM: dts: renesas: Add R8A779A0 V3U DTs"
by Hai Pham <hai.pham.ud@renesas.com>

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
2021-06-24 20:22:17 +02:00
Marek Vasut
6232d0a740 ARM: dts: renesas: Add R8A779A0 V3U Falcon DTs
Import R8A779A0 V3U Falcon DTs from Linux 5.12,
commit 9f4ad9e425a1 ("Linux 5.12") .

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
2021-06-24 20:22:17 +02:00
Marek Vasut
b6ec11b62d ARM: dts: renesas: Add R8A779A0 V3U DTs and headers
Import R8A779A0 V3U DTs and headers from Linux 5.12,
commit 9f4ad9e425a1 ("Linux 5.12") .

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
2021-06-24 20:22:17 +02:00
Michal Simek
3972ae65e4 arm64: zynqmp: Add missing year in Kria dts files
DT files have been added this year but forgot to update it that's why do it
in separate patch now.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-06-23 09:48:36 +02:00
Michal Simek
9899f3e6b9 arm64: zynqmp: Add psgtr description to zc1751 dc1 board
Wire psgtr for zc1751 dc1 board.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-06-23 09:48:36 +02:00
Michal Simek
52caf2c12b arm64: zynqmp: Remove gpio from aliases list
It is not recommended to have aliases for gpio. In past it was used in
Linux for assigning numbers via sysfs which is deprecated and libgpiod
should be used instead.
In U-Boot this number is used for seq number but gpio offset are not
counted from this number. That's why having these aliases only for seq
number is not needed. As is done in Linux it is the best to use full gpio
name instead of sequence number which depends on sequence in binding.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-06-23 09:48:36 +02:00
Michal Simek
83dc13384b arm64: zynqmp: Enable USB3.0 for dc2/dc3
Both boards are usb3.0 capable. dc3 was also missing enabling dwc3* nodes.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-06-23 09:48:36 +02:00
Michal Simek
cb4380abfd arm64: zynqmp: Update usb dwc3 DT description
Align USB nodes with the latest dt-bindings. It is adding resets, new
interrupt and also some quirks.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-06-23 09:48:36 +02:00
Michal Simek
b6d8d4b100 arm64: zynqmp: Use overlay sugar syntax for Kria SOM
dtc supports new sugar syntax which is easier compare to previous one
that's why also covert overlays for SOM to it.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-06-23 09:48:35 +02:00
Michal Simek
3dbd53144c arm64: zynqmp: Remove revA compatibility string from kv260 revB/1
kv260-revB is different compare to revA (usbhub is wired via i2c) that's
why remove revA compatible string.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-06-23 09:48:35 +02:00
Michal Simek
6a2ce6ec24 arm64: zynqmp: Sync psgtr location on zcu104/zcu111/zc1751-dc1
psgtr node should be below pinctrl for easier comparion among dts files.
That's why move that nodes to different location.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-06-23 09:48:35 +02:00
Michal Simek
e0f99280ee arm64: zynqmp: Remove information about dma clock on zcu106
Clock setting is not static anymore that's why it depends on firmware setup
that's why remove this comment.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-06-23 09:48:35 +02:00
Michal Simek
d245d0dfd8 arm64: zynqmp: Remove unused property from SD/USB
Linux kernel is not using these properties that's why they can be removed.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-06-23 09:48:35 +02:00
Michal Simek
0c79419d35 arm64: zynqmp: Remove can aliases from zc1751
Networking subsystem is not using aliases that's why remove them for CAN
devices. There is also no any other Xilinx ZynqMP DT file with them.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-06-23 09:48:35 +02:00
Michal Simek
43086886ad arm64: zynqmp: Remove si5328 and si5382 nodes
There are no drivers for these devices that's why remove that nodes
completely. This change is done based on Linux kernel.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/20210308115437.2232847-1-quanyang.wang@windriver.com
2021-06-23 09:48:35 +02:00
Michal Simek
531abcb71e xilinx: Convert xlnx,eeprom property to nvmem alias
Convert all boards to use nvmem alias instead of xlnx,eeprom. The change is
done based on discussion in the link below.

Link: https://lore.kernel.org/r/CAL_JsqLMDqpkyg-Q7mUfw-XH67-v068Q6e9wTq2UOoN=0-_coQ@mail.gmail.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-06-23 09:48:35 +02:00
Srinivas Neeli
ee6b3c54e9 arm64: zynqmp: rtc: Update rtc calibration value
As per the design specification
"The 16-bit Seconds Calibration Value represents the number of
 Oscillator Ticks that are required to measure the largest time
 period that is less than or equal to 1 second.
 For an oscillator that is 32.768 KHz, this value will be 0x7FFF."

Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-06-23 09:48:35 +02:00
Michal Simek
5fa9672248 arm64: zynqmp: Sync psgtr location on zcu100/zcu106
psgtr node should be below pinctrl for easier comparion among dts files.
That's why move that nodes to different location.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-06-23 09:48:35 +02:00
Michal Simek
abd30371d3 arm64: zynqmp: Sync dp port location on zc1751 dc4
Historically dpdma and dpsub are placed at the end of files. Move nodes
there for easier comparison among dts files.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-06-23 09:48:35 +02:00
Michal Simek
af04516992 arm64: zynqmp: Remove unused dp_aclk clock
dp_aclk is not used anywhere that's why remove it.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-06-23 09:48:35 +02:00
Michal Simek
70fbcdb825 arm64: zynqmp: Remove addition newline from zc1751 dc1
Trivial patch.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-06-23 09:48:35 +02:00
Michal Simek
184309b8c6 arm64: zynqmp: Add maximum-speed property for dwc3 nodes
dwc3 can be used only for higher speeds than super-speed that's why
explicitly set it up.
This is also aligned with other ZynqMP dts files.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-06-23 09:48:35 +02:00
Michal Simek
7c3ad8f6a3 arm64: zynqmp: Remove additional header from zc1232 DT
Remove unused phy.h from zc1232 DTS.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-06-23 09:48:35 +02:00
Michal Simek
02860e1562 zynqmp: Remove u-boot,dm-pre-reloc for uart instances
Uarts already have u-boot,dm-pre-reloc via zynqmp.dtsi that's why there is
no need to have them in platform DT files too.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-06-23 09:48:35 +02:00
Michal Simek
447fb8db02 arm64: zynqmp: Update Copyright years to 2021
Trivial change for all files I have touched recently.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-06-23 09:48:35 +02:00
Michal Simek
eca0376b54 arm64: zynqmp: Add label for zynqmp_ipi
Add label which is used by bootloader for adding bootloader specific flag.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/3dc8416abdd3498e61edcd83830a12af295c5c6d.1611224800.git.michal.simek@xilinx.com
2021-06-23 09:48:35 +02:00
Michal Simek
f2b5dd38de arm64: zynqmp: Move DP nodes to the end of file (zcu106)
Just sync it with others for easier comparison.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-06-23 09:48:35 +02:00
Michal Simek
fee3e307f2 arm64: zynqmp: Add reset description for sata
Sata needs to get reset before configuration that's why add property for it
there.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-06-23 09:48:35 +02:00
Stefano Stabellini
ce42bd2fa3 arm64: zynqmp: Add missing SMID for pcie to zynqmp.dtsi
The SMMU is disabled in device tree so this change has no impact.
The benefit is that this way it is in sync with xen.dtsi. Xen enables
the SMMU and makes use of it.

Signed-off-by: Stefano Stabellini <stefano.stabellini@xilinx.com>
2021-06-23 09:48:35 +02:00
Michal Simek
d9be8b4f2f arm64: zynqmp: Disable CCI by default
There is no reason to have CCI no enabled by default. Enable it when your
system configuration requires it. In Xilinx configuration flow this is
work for Device Tree Generator which reads information from HW Design
configuration.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-06-23 09:48:35 +02:00
Michal Simek
1242a6b13d arm64: zynqmp: Update psgtr clocks index for boards
Update the psgtr clock indexing for couple of zynqmp boards.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-06-23 09:48:35 +02:00
Michal Simek
767aa16d41 ARM: zynq: Rename bus to be align with simple-bus yaml
Rename amba to AXI. Based on Xilinx Zynq TRM (Chapter 5) chip is "AXI
point-to-point channels for communicating addresses, data, and response
transactions between master and slave clients. This ARM AMBA 3.0..."

Issues are reported as:
.. amba: $nodename:0: 'amba' does not match
'^([a-z][a-z0-9\\-]+-bus|bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
>From schema:
../github.com/devicetree-org/dt-schema/dtschema/schemas/simple-bus.yaml

Similar change has been done for Xilinx ZynqMP SoC.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/8a4bc80debfbb79c296e76fc1e4c173e62657286.1606397101.git.michal.simek@xilinx.com
2021-06-23 09:48:35 +02:00
Michal Simek
351b9f5f95 arm64: zynqmp: Enable gpio driver for zcu1275/zcu1285
Enable gpio driver on these boards. GPIOs can be used on any board.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-06-23 09:48:35 +02:00
Michal Simek
e246dc49cf ARM: zynq: Fix OCM mapping to be aligned with binding on zc702
The Linux commit f69629919942 ("dt-bindings: sram: Convert SRAM bindings to
json-schema") converted binding to yaml and some missing required
properties started to be reported. Align binding based on it.

The patch is fixing these warnings:
.../zynq-zc702.dt.yaml: sram@fffc0000: '#address-cells' is a required property
.../zynq-zc702.dt.yaml: sram@fffc0000: '#size-cells' is a required property
.../zynq-zc702.dt.yaml: sram@fffc0000: 'ranges' is a required property
>From schema: .../Documentation/devicetree/bindings/sram/sram.yaml

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/87c02786ccd8d7827827a9d95a8737bb300caeb0.1606397101.git.michal.simek@xilinx.com
2021-06-23 09:48:35 +02:00
Michal Simek
742fdd1e6b ARM: zynq: Convert at25 binding to new description on zc770-xm013
The Linux commit f8f79fa6bb25 ("dt-bindings: at25: convert the binding
document to yaml") converted binding to yaml and 3 deprecated properties
pop up.

The patch is fixing these warnings:
.../zynq-zc770-xm013.dt.yaml: eeprom@2: 'pagesize' is a required property
.../zynq-zc770-xm013.dt.yaml: eeprom@2: 'size' is a required property
.../zynq-zc770-xm013.dt.yaml: eeprom@2: 'address-width' is a required property
>From schema: .../Documentation/devicetree/bindings/eeprom/at25.yaml

by converting them to new binding.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/be2c1125d98386033e182012eb08986924707a76.1606397101.git.michal.simek@xilinx.com
2021-06-23 09:48:35 +02:00
Vignesh Raghavendra
95eca8612b ARM: dts: k3-j7200-common-proc-board-u-boot.dtsi: Fix dtc warnings
Fix following dtc warning by explicitly setting up #size-cells
and #address-cells when overriding node in -u-boot.dtsi

arch/arm/dts/k3-j7200-common-proc-board.dtb: Warning (reg_format):
/bus@100000/bus@28380000/mcu-navss/ringacc@2b800000:reg: property has
invalid length (80 bytes) (#address-cells == 2, #size-cells == 1)

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
2021-06-21 13:18:17 -04:00
Fabio Estevam
31b3829f74 o4-imx-nano: Fix dtc warnings
Remove the LED unit addresses and reg properties to
fix the following dtc build warnings:

arch/arm/dts/o4-imx-nano.dtb: Warning (reg_format): /leds/led@0:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1)
...
arch/arm/dts/o4-imx-nano.dtb: Warning (avoid_default_addr_size): /leds/led@0: Relying on default #address-cells value

Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Oleh Kravchenko <oleg@kaa.org.ua>
2021-06-21 13:31:40 +02:00
Tom Rini
28afb71646 Merge tag 'u-boot-rockchip-20210618' of https://source.denx.de/u-boot/custodians/u-boot-rockchip into next
- New SoC platform support: rk3568;
- rockchip pcie Code compile issue fix;
- Board fix for rk3399 Khadas Edge;
- Add Rockchip NFC driver;
2021-06-19 08:20:12 -04:00
Michael Walle
82a3c9ef20 net: use the same alias stem for ethernet as linux
Linux uses the prefix "ethernet" whereas u-boot uses "eth". This is from
the linux tree:

$ grep "eth[0-9].*=.*&" arch/**/*dts{,i}|wc -l
0
$ grep "ethernet[0-9].*=.*&" arch/**/*dts{,i}|wc -l
633

In u-boot device trees both prefixes are used. Until recently the only
user of the ethernet alias was the sandbox test device tree. This
changed with commit fc054d563b ("net: Introduce DSA class for Ethernet
switches"). There, the MAC addresses are inherited based on the devices
sequence IDs which is in turn given by the device tree.

Before there are more users in u-boot and both worlds will differ even
more, rename the alias prefix to "ethernet" to match the linux ones.
Also adapt the test cases and rename any old aliases in the u-boot
device trees.

Cc: David Wu <david.wu@rock-chips.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2021-06-18 11:29:17 +03:00
Joseph Chen
636ffbd25c arm: dts: rockchip: Add dts for rk3568 evb
Add dts for rk3568 evb, sync from the linux kernel
upstream list [0].

[0] https://patchwork.kernel.org/project/linux-rockchip/list/?series=474969

Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2021-06-18 14:36:24 +08:00
Joseph Chen
a4a9ce1660 arm: dts: Sync rockchip-pinconf.dtsi from kernel
Sync from linux kernel:
https://patchwork.kernel.org/project/linux-rockchip/list/?series=474969

Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2021-06-18 14:36:24 +08:00
Grzegorz Szymaszek
95a34eb42e arm: dts: stm32mp157c-odyssey-som: enable SDMMC2 in SPL
Enable the SDMMC2 device tree node, as well as the pins it uses, in
U-Boot SPL.

Signed-off-by: Grzegorz Szymaszek <gszymaszek@short.pl>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
2021-06-18 08:34:16 +02:00
Grzegorz Szymaszek
7db3307848 arm: dts: stm32mp157c-odyssey-som: enable the SDMMC2 eMMC HS DDR mode
Enable the SDMMC2 eMMC high-speed DDR mode as it is done in the
corresponding Linux kernel device tree.

Signed-off-by: Grzegorz Szymaszek <gszymaszek@short.pl>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
2021-06-18 08:34:16 +02:00
Grzegorz Szymaszek
51a2ac966e arm: dts: stm32mp157c-odyssey-som: set the SDMMC2 VQMMC supply
Set the SDMMC2 VQMMC supply to vdd (buck3). Note that in the
corresponding Linux kernel device tree, the supply is set to v3v3
(buck4), which is wrong.

Signed-off-by: Grzegorz Szymaszek <gszymaszek@short.pl>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
2021-06-18 08:34:16 +02:00
Grzegorz Szymaszek
b1c8ad53f5 arm: dts: stm32mp157c-odyssey-som: enable all SDMMC2 data lanes
Add the “sdmmc2_d47_pins_d” pins to the SDMMC2 pinctrls. Increase the
bus width from four to eight.

Signed-off-by: Grzegorz Szymaszek <gszymaszek@short.pl>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
2021-06-18 08:34:16 +02:00
Grzegorz Szymaszek
b40a034a63 arm: dts: stm32mp157c-odyssey-som: fix the basic SDMMC2 properties
The SDMMC2 interface hosts an eMMC. Replace the interface properties
that would only apply to SD cards—“broken-cd” and “disable-wp”—with
relevant ones: “non-removable”, “no-sd” and “no-sdio”.

Signed-off-by: Grzegorz Szymaszek <gszymaszek@short.pl>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
2021-06-18 08:34:16 +02:00
Tom Rini
a298d4fbcd Merge https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriq
- fsl-qoriq: Bug fixes related pfe, eth, thermal node, vid.c, cpu release,
  mmc, usb, env, etc for Layerscape boards
- powerpc: Update Maintainers for some boards.
2021-06-17 08:44:56 -04:00
Aleksandar Gerasimovski
a7fd6fa1c2 board/km: add support for expu1 design based on nxp
The EXPU1 design is a new 40G capable ethernet service unit card for
Hitachi-Powergrids wired-com product lines.

The base SoC is same as for already added SELI8 card, consequently the
already added u-boot support for SELI8 is reused.

Signed-off-by: Rainer Boschung <rainer.boschung@hitachi-powergrids.com>
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
[Fixed new line error at EOF]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-06-17 11:46:11 +05:30
Lasse Klok Mikkelsen
fb6c96f14e arm: dts: ls1021a.dtsi: Fix invalid reg on gpio nodes
Address and size cells on SOC are set to 1. But gpio nodes are specified
with 2 cells. This fixes the gpio nodes to correct cells.

Signed-off-by: Lasse Klok Mikkelsen <lkmi@prevas.dk>
Reviewed-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-06-17 11:46:11 +05:30
Yangbo Lu
38d1a18750 arm: dts: lx2162aqds: support eMMC HS400 mode on esdhc1
Add properties related to eMMC HS400 mode for esdhc1.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-06-17 11:46:11 +05:30
Tom Rini
b2c4b7f665 u-boot-imx-20210616
-------------------
 
 - imxrt : fixes, USB, imxrt1020-evk
 - imx8m:
 	fix for verdin-imx8mm
 	Add conga-QMX8 board
 - imx6 :
 	documentation for pico-imx6:
 	Add SeeedStudio NPI-IMX6ULL Support
 	ventana: DM PCI
 - imx7d:
 	added SMEGW01 board
 
 CI : https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/7765
 -----BEGIN PGP SIGNATURE-----
 
 iG0EABECAC0WIQS2TmnA27QKhpKSZe309WXkmmjvpgUCYMoTAg8cc2JhYmljQGRl
 bnguZGUACgkQ9PVl5Jpo76aaXgCfa0IWXD0nOT0xQ50aKZGD3fspahsAn3rfnviv
 HnrT4j7bdBRksuYJ15PR
 =NEGm
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-imx-20210616' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx

u-boot-imx-20210616
-------------------

- imxrt : fixes, USB, imxrt1020-evk
- imx8m:
	fix for verdin-imx8mm
	Add conga-QMX8 board
- imx6 :
	documentation for pico-imx6:
	Add SeeedStudio NPI-IMX6ULL Support
	ventana: DM PCI
- imx7d:
	added SMEGW01 board

CI : https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/7765
2021-06-16 11:18:11 -04:00
Michael Walle
2bf4658b8c board: sl28: fix RGMII clock and voltage
It was noticed that the clock isn't continuously enabled when there is
no link. This is because the 125MHz clock is derived from the internal
PLL which seems to go into some kind of power-down mode every once in a
while. The LS1028A expects a contiuous clock. Thus enable the PLL all
the time.

Also, the RGMII pad voltage is wrong, it was configured to 2.5V (that is
the VDDH regulator). The correct voltage is 1.8V, i.e. the VDDIO
regulator.

Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-06-16 18:14:08 +05:30
Vignesh Raghavendra
2af181b53e ARM: dts: k3: Add cfg register space for ringacc and udmap
R5 SPL needs access to cfg space of Rings and UDMAP, therefore add RING
CFG, TCHAN CFG and RCHAN CFG address ranges.
Note that these registers are present within respective IPs but are
not populated in Linux DT nodes (as they are configured via TISCI APIs)
and hence are added to -u-boot.dtsi for now.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210607141753.28796-6-vigneshr@ti.com
2021-06-11 19:18:52 +05:30