Commit 0934dddc64 ("arm: a37xx: Update DTS files to version from
upstream Linux kernel") ported Linux's device-tree files for Armada 3720
SOCs. This broke network on Turris MOX, because the SOC's MDIO bus in
U-Boot currently isn't probed via DM as it's own device, but is
registered as part of mvneta's driver, which means that pinctrl
definitions are not parsed for the MDIO bus node. Also mvneta driver
does not consider "phy-handle" property, only "phy".
For now, fix this by adding armada-3720-turris-mox-u-boot.dtsi file
returning the MDIO to how it was defined previously.
A better solution (using proper mvmdio DM driver) is being work on, but
will need testing on various boards, and we need the bug fixed now for
the upcoming release.
Fixes: 0934dddc64 ("arm: a37xx: Update DTS files to version from upstream Linux kernel")
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
This patch configures U-Boot SPL for DHCOM SoM to permit DFU upload of
SPL and subsequent u-boot.itb for recovery or commissioning purposes.
The DFU usage procedure is identical to STM32MP1 DHCOR SoM, see commit
3919aa1722 ("ARM: dts: stm32: Add DFU support for DHCOR recovery") ,
except for switching the SoM into DFU mode. By default, the DHCOM SoM
has no dedicated mechanism for setting BOOTn straps into UART/USB mode,
therefore to enter DFU mode, the SoC must fail to boot from boot media
which can be selected by the BOOTn strap override mechanism first and
then fall back to DFU mode.
In case of a SoM with pre-populated BOOTn strap override button, power
the system off, remove microSD card (if applicable), hold down the BOOTn
strap override button located between eMMC and SoM edge connector, power
on the SoM. The SoC will fail to boot from SD card and fall back into
DFU mode.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Implement PSCI system suspend and placement of DRAM into SSR while the
CPUs are in suspend. This saves non-trivial amount of power in suspend,
on 2x W632GU6NB-15 ~710mW.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
The vdd_io regulator is present only on DHCOR SoM configured for 1V8 IO,
as populated on Avenger96, but not present on 3V3 DHCOR SoM. Move these
extras to Avenger96 u-boot DT extras.
Fixes: 3919aa1722 ("ARM: dts: stm32: Add DFU support for DHCOR recovery")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Fix the following warning in SPL and make sure that even DTs which
enforce Vbus detection using u-boot,force-vbus-detection;, the DFU
in SPL will work.
dwc2-udc-otg usb-otg@49000000: prop pinctrl-0 index 0 invalid phandle
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Device tree alignment with Linux kernel v5.17-rc1
- ARM: dts: stm32: add pull-up to USART3 and UART7 RX pins
on STM32MP15 DKx boards
- ARM: dts: stm32: clean uart4_idle_pins_a node for stm32mp15
- ARM: dts: stm32: tune the HS USB PHYs on stm32mp15xx-dkx
- ARM: dts: stm32: tune the HS USB PHYs on stm32mp157c-ev1
- ARM: dts: stm32: fix stusb1600 pinctrl used on stm32mp157c-dk
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add the missing @dev reference in some function description.
Fixes: b66bfdf238 ("arm: stm32mp: bsec: migrate trace to log macro")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add support of the permanent lock support in U-Boot proper
when BSEC is not managed by secure monitor (TF-A SP_MIN or OP-TEE).
This patch avoid issue with stm32key command and fuse command
on basic boot for this missing feature of U-Boot BSEC driver.
Reported-by: Johann Neuhauser <jneuhauser@dh-electronics.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Tested-by: Johann Neuhauser <jneuhauser@dh-electronics.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
After double checking some i2c addresses are not correct. It is visible
from i2c dump
ZynqMP> i2c bus
Bus 3: i2c@ff020000
74: i2c-mux@74, offset len 1, flags 0
Bus 5: i2c@ff020000->i2c-mux@74->i2c@0
Bus 6: i2c@ff020000->i2c-mux@74->i2c@2
Bus 7: i2c@ff020000->i2c-mux@74->i2c@1
Bus 8: i2c@ff020000->i2c-mux@74->i2c@3
Bus 4: i2c@ff030000 (active 4)
74: i2c-mux@74, offset len 1, flags 0
Bus 9: i2c@ff030000->i2c-mux@74->i2c@0
Bus 10: i2c@ff030000->i2c-mux@74->i2c@3
Bus 11: i2c@ff030000->i2c-mux@74->i2c@4
Bus 12: i2c@ff030000->i2c-mux@74->i2c@5 (active 12)
51: generic_51, offset len 1, flags 0
60: generic_60, offset len 1, flags 0
74: generic_74, offset len 1, flags 0
Bus 13: i2c@ff030000->i2c-mux@74->i2c@6 (active 13)
51: generic_51, offset len 1, flags 0
5d: generic_5d, offset len 1, flags 0
74: generic_74, offset len 1, flags 0
ZynqMP> i2c dev 4
Setting bus to 4
ZynqMP> i2c mw 74 0 18
ZynqMP> i2c probe
Valid chip addresses: 18 36 37 50 51 60 74
ZynqMP> i2c mw 74 0 20
ZynqMP> i2c probe
Valid chip addresses: 51 60 74
where it is clear that si570 (u5) is at 0x60 address and 8t49n240 (u39) is
also at address 0x60 based on log above.
i2c address 0x74 is i2c mux and 0x51 is eeprom.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/0a198e9d993411e41473d130d5a5c20b6dc83458.1646639616.git.michal.simek@xilinx.com
Remap PCI I/O space to the bus address 0x0 in the Armada 37xx device-tree
in order to support legacy I/O port based cards which have hardcoded I/O
ports in low address space.
Some legacy PCI I/O based cards do not support 32-bit I/O addressing.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This adds platform code and the device tree for the Phytium Pomelo Board.
The initial support comprises the UART and the PCIE.
Signed-off-by: weichangzheng <nicholas_zheng@outlook.com>
get_osc_clk_speed and get_sys_clkin_sel are only used in
one file. Make them static.
Tested on OMAP3530, DM3730, AM3517.
Signed-off-by: Adam Ford <aford173@gmail.com>
Sync the am3517-evm device tree files with those from Linux
5.17-rc5 with some additional fixes for pinmuxing Ethernet and
moving the pinmux references to the respective peripherals.
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Derald D. Woods <woods.technical@gmail.com>
Resync the DTS files for the Logic PD SOM-LV with Linux 5.17-rc5
with some additional pending changes to address issues with
wrong pin-muxing on the OMAP35.
Signed-off-by: Adam Ford <aford173@gmail.com>
Instead of a special function, send an event after driver model is inited
and adjust the boards which use this function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Commit 7945caf22c ("arm: sunxi: Enable SPI/SPI-FLASH support for A64")
selected CONFIG_SPI by default on all Allwinner A64 boards, even though
only 4 out of the 14 A64 boards have a SPI flash chip. All other SoCs
had to manually select DM_SPI and friends, even though they are a
platform property (the sunxi SPI driver is DM_SPI only).
Clean this up to allow easy selection of SPI flash support in U-Boot
proper, by selecting DM_SPI and DM_SPI_FLASH *if* CONFIG_SPI is
selected, for *all* Allwinner SoCs. This simplifies the defconfig for
two Libretech boards already.
Also remove the forced CONFIG_SPI from the A64 Kconfig, instead let the
four boards which allow SPI booting select this explicitly.
Any board wishing to support SPI flash in U-Boot proper now just defines
CONFIG_SPI and CONFIG_SPI_FLASH_<vendor> in its defconfig, Kconfig takes
care of the rest.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
This code has been ported from Linux v5.16.9 arch/arm/boot/dts/am33xx.dtsi
file to allow correct usage of MMC2 controller in U-Boot.
This IP block is a bit specific as it is connected to L3 interconnect bus,
whereas mmc[01] are connected to L4.
Proper configuration of this block (including providing clock) is handled
in ti-sysc.c driver.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This change provides similar aliases definitions as now present in
Linux kernel v5.16.9 for am33xx.dtsi file.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Enable the led in the device tree of the refboard bcm96753ref.
It also defines two leds (led_red ad led_green).
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
This add the initial support of the broadcom reference
board bcm96753ref with a bcm6753 SoC.
This board has 1 GB of RAM, 256 MB of flash (nand),
2 USB port, 1 UART, and 4 ethernet ports.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
The main reason is to send pmufw cfg overlay from U-Boot to PMUFW to enable
access to DP. Overlay is sent when cls command is called and for that IP
has to be enabled in carrier cards.
And IP needs to be also enabled in SOM dt because with DTB reselection new
DT is not parsed in pre reloc U-Boot instance. It is called from board_f
via embedded_dtb_select(). That's why bind function is not able to allocate
memory and it ends up with error:
"Video device 'display@fd4a0000' cannot allocate frame buffer memory
-ensure the device is set up before relocation"
To avoid this situation DP is placed also to SOM where bind function is
called and frame buffer memory is allocated and just reused after DTB
reselection. Result is the same. There could be a problem in Linux with
different DP configurations but that's need to be solved there because
console should be on from u-boot already.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/c4f31641f917fddb09d976f56875057c658f264c.1645629459.git.michal.simek@xilinx.com
Use ethernet-phy-id compatible string to properly describe phy reset on
kv260 boards. Previous description wasn't correct because reset was done
for mdio bus to operate and it was in this case used for different purpose
which was eth phy reset. With ethernet-phy-id phy reset happens only for
the phy via phy framework.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/73b64f1a2b873b4e26bd2b365364bdf313794ae2.1645629459.git.michal.simek@xilinx.com
With limited low level configuration done via psu-init only IPs connected
on SOM are initialized and configured. All IPs connected to carrier card
are not initialized. There is a need to do proper reset, pin configuration
and also clock setting.
The patch targets the last part which is setting up proper clock for USBs
and SDs.
Also setup proper bus width for SD cards.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Sai Krishna Potthuri <lakshmi.sai.krishna.potthuri@xilinx.com>
Link: https://lore.kernel.org/r/d9f80b2551bd246c3d7ecb09b516806c8dc83ed9.1645629459.git.michal.simek@xilinx.com
Recent unrelated fixes (9876ae7db6) revealed that we were missing bits
from 2af181b53e in the IOT2050 dt. Add them, but only for main U-Boot.
SPL loads from QSPI only, thus cannot use DMA.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
We only want to call do_board_detect() if CONFIG_TI_I2C_BOARD_DETECT
is set. Same as done for am64.
This makes it possible to add a custom am65 based board design to
U-Boot that does not use this board detection mechanism.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
The a3700_fdt_fix_pcie_regions() function still computes nonsense.
It computes the fixup offset from the PCI address taken from the first
row of the "ranges" array, which means that:
- PCI address must equal CPU address (otherwise the computed fix offset
will be wrong),
- the first row must contain the lowest address.
This is the case for the default device-tree, which is why we didn't
notice it.
It also adds the fixup offset to all PCI and CPU addresses, which is
wrong.
Instead:
1) The fixup offset must be computed from the CPU address, not PCI
address.
2) The fixup offset must be computed from the row containing the lowest
CPU address, which is not necessarily contained in the first row.
3) The PCI address - the address to which the PCIe controller remaps the
address space as seen from the point of view of the PCIe device -
must be fixed by the fix offset in the same way as the CPU address
only in the special case when the CPU adn PCI addresses are the same.
Same addresses means that remapping is disabled, and thus if we
change the CPU address, we need also to change the PCI address so
that the remapping is still disabled afterwards.
Consider an example:
The ranges entries contain:
PCI address CPU address
70000000 EA000000
E9000000 E9000000
EB000000 EB000000
By default CPU PCIe window is at: E8000000 - F0000000
Consider the case when TF-A moves it to: F2000000 - FA000000
Until now the function would take the PCI address of the first entry:
70000000, and the new base, F2000000, to compute the fix offset:
F2000000 - 70000000 = 82000000, and then add 8200000 to all addresses,
resulting in
PCI address CPU address
F2000000 6C000000
6B000000 6B000000
6D000000 6D000000
which is complete nonsense - none of the CPU addresses is in the
requested window.
Now it will take the lowest CPU address, which is in second row,
E9000000, and compute the fix offset F2000000 - E9000000 = 09000000,
and then add it to all CPU addresses and those PCI addresses which
equal to their corresponding CPU addresses, resulting in
PCI address CPU address
70000000 F3000000
F2000000 F2000000
F4000000 F4000000
where all of the CPU addresses are in the needed window.
Fixes: 4a82fca8e3 ("arm: a37xx: pci: Fix a3700_fdt_fix_pcie_regions() function")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
This converts the following to Kconfig:
CONFIG_CHIP_SELECTS_PER_CTRL
Cc: Alison Wang <alison.wang@nxp.com>
Cc: Pramod Kumar <pramod.kumar_1@nxp.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These particular values are not configurable and today we always set
CONFIG_SECURE_BL1_ONLY. Move these to where they're used in the code,
and drop from the CONFIG namespace.
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmIgkpAcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyDmXCACMc7jIpdFEz2NKTnSy
hudLhzWTQ8NrPFrOkxAJREMaMhRCh5b/5AW0469fFFZ86NxpgHyuoNJtnflN/V8t
ucVfM3/fJgfoyBnfyzv+Cuju8DQNGZZnBrYKBeIKzlD8/nwX0Ah/xbGb/IKCD3cT
IVl8UqXh57NDVYApb/04sDK1hNfjex3jYejH/l8pQYiF/fsfYQI9XPGdD0w4N6N1
D1Rtpmr9lJqJiq7xjCIwHoqigYV4E7lu5P4Uk9RzxBOo8BAcrn10DMgjlg9AL4F/
LqmLCTC65myV5tqrdVES6EHke7S3QD9vi6qB4qB/tr/AE3c/4cdzGUL7nkyzI1Cq
iZlg
=9HIi
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-fixes-2022.04-a' of https://source.denx.de/u-boot/custodians/u-boot-at91
First set of u-boot-atmel fixes for the 2022.04 cycle:
This fixes set includes only a single fix for the Ethernet on sama7g5ek
board which is broken at the moment.
Commit 88998f7775 ("arm: arm926ej-s: Add sunxi code") introduced
the ARM926 version of the code to save and restore some FEL state, to
be able to return to the BROM FEL code after the SPL has run.
However during review a change was made, that happened to mess up the
register restore part, so SCTLR and CPSR ended up with the wrong values,
breaking return to FEL.
Use the same offset that we actually save those registers to, to make
FEL booting actually work on the Lichee Pi Nano.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Enable SPI boot in SPL on SUNIV architecture and use
it in the licheepi nano that uses the F1C100s.
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The SUNIV SoCs come with a sun6i-style SPI controller at the base address
of sun4i SPI controller. The module clock of the SPI controller is
missing which leaves us running directly from the AHB clock, which is
set to 200MHz.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
[Icenowy: Original implementation]
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
[Jesse: adaptation to Upstream U-Boot]
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
In contrast to other Allwinner SoCs the F1C100s BROM does not store a
boot source indicator in the eGON header in SRAM. This leaves the SPL
guessing where we were exactly booted from, and for instance trying
the SD card first, even though we booted from SPI flash.
By inspecting the BROM code and by experimentation, Samuel found that the
top of the BROM stack contains unique pointers for each of the boot
sources, which we can use as a boot source indicator.
This patch removes the existing board_boot_order bodge and replace it
with a proper boot source indication function.
The only caveat is that this only works in the SPL, as the SPL header
gets overwritten with the exception vectors, once U-Boot proper takes
over. Always return MMC0 as the boot source, when called from U-Boot
proper, as a placeholder for now, until we find another way.
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Suggested-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The branch_if_master macro jumps to a label if the CPU is the "master"
core, which we define as having all affinity levels set to 0. To check
for this condition, we need to mask off some bits from the MPIDR
register, then compare the remaining register value against zero.
The implementation of this was slighly broken (it preserved the upper
RES0 bits), overly complicated and hard to understand, especially since
it lacked comments. The same was true for the very similar
branch_if_slave macro.
Use a much shorter assembly sequence for those checks, use the same
masking for both macros (just negate the final branch), and put some
comments on them, to make it clear what the code does.
This allows to drop the second temporary register for branch_if_master,
so we adjust all call sites as well.
Also use the opportunity to remove a misleading comment: the macro
works fine on SoCs with multiple clusters. Judging by the commit
message, the original problem with the Juno SoC stems from the fact that
the master CPU *can* be configured to be from cluster 1, so the
assumption that the master CPU has all affinity values set to 0 does not
hold there. But this is already mentioned above in a comment, so remove
the extra comment.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The switch_el macro is a neat contraption to handle cases where we need
different code depending on the current exception level, but its
implementation was longer than needed.
Simplify it by doing just one comparison, then using the different
condition codes to branch to the desired target. PState.CurrentEL just
holds two bits, and since we don't care about EL0, we can use >, =, < to
select EL3, EL2 and EL1, respectively.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
asm/io.h is the header file containing the central MMIO accessor macros.
Judging by the header and the comments, it was apparently once copied
from the Linux kernel, but has deviated since then *heavily*. There is
absolutely no point in staying close to the original Linux code anymore,
so just remove the old cruft, by:
- removing pointless Linux history
- removing commented code
- removing outdated comments
- removing unused definitions (for mem_isa)
This massively improves the readability of the file.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
In ARMv8 we have the choice between two stack pointers to use: SP_EL0 or
SP_ELx, which is banked per exception level. This choice is stored in
the SP field of PState, and can be read and set via the SPSel special
register. When the CPU takes an exception, it automatically switches to
the SP_ELx stack pointer.
Trusted Firmware enters U-Boot typically with SPSel set to 1, so we use
SP_ELx all along as our sole stack pointer, both for normal operation and
for exceptions.
But if we now for some reason enter U-Boot with SPSel cleared, we will
setup and use SP_EL0, which is fine, but leaves SP_ELx uninitialised.
When we now take an exception, we try to save the GPRs to some undefined
location, which will usually end badly.
To make sure we always have SP_ELx pointing to some memory, set SPSel
to 1 in the early boot code, to ensure safe operation at all times.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The ARMv8 architecture describes the "SError interrupt" as the fourth
kind of exception, next to synchronous exceptions, IRQs, and FIQs.
Those SErrors signal exceptional conditions from which the system might
not easily recover, and are normally generated by the interconnect as a
response to some bus error. A typical situation is access to a
non-existing memory address or device, but it might be deliberately
triggered by a device as well.
The SError interrupt replaces the Armv7 asynchronous abort.
Trusted Firmware enters U-Boot (BL33) typically with SErrors masked,
and we never enable them. However any SError condition still triggers
the SError interrupt, and this condition stays pending, it just won't be
handled. If now later on the Linux kernel unmasks the "A" bit in PState,
it will immediately take the exception, leading to a kernel crash.
This leaves many people scratching their head about the reason for
this, and leads to long debug sessions, possibly looking at the wrong
places (the kernel, but not U-Boot).
To avoid the situation, just unmask SErrors early in the ARMv8 boot
process, so that the U-Boot exception handlers reports them in a timely
manner. As SErrors are typically asynchronous, the register dump does
not need to point at the actual culprit, but it should happen very
shortly after the condition.
For those exceptions to be taken, we also need to route them to EL2,
if U-Boot is running in this exception level.
This removes the respective code snippet from the Freescale lowlevel
routine, as this is now handled in generic ARMv8 code.
Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Support for Apple M1 Pro and Max will allow using a single binary for
all M1 SoCs. The M1 Pro/Max have a different memory layout. The RAM
start address is 0x100_0000_0000 instead of 0x8_0000_0000.
Replace the hardcoded memory layout with dynamic initialized
environment variables in board_late_init().
Tested on Mac Mini (2020) and Macbook Pro 14-inch (2021).
Signed-off-by: Janne Grunau <j@jannau.net>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Simplify the binman config and fdt nodes by using the "@..-SEQ"
substitutions and CONFIG_OF_LIST.
Signed-off-by: Michael Walle <michael@walle.cc>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
omap_ehci_hcd_stop appears to be dead code, and omap_ehci_hcd_init
is only called by the probe function, so it can be static to that
function. Remove both from the header along with some additional
checking for DM_USB.
Signed-off-by: Adam Ford <aford173@gmail.com>
The default U-Boot environment variables and design are all set up for
the MAIN R5FSS cluster to be in Split-mode. This is the setting used
when the dts nodes were originally added in v2021.01 U-Boot and the
dt nodes are synched with the kernel binding property names in
commit 468ec2f3ef ("remoteproc: k3_r5: Sync to upstreamed kernel DT
property names") merged in v2021.04-rc2.
The modes for the MAIN R5FSS cluster got switched back to LockStep mode
by mistake in commit fa09b12dc5 ("arm: ti: k3: Resync dts files and
bindings with Linux Kernel v5.14") in v2022.01-rc1. This throws the
following warning messages when early-booting the cores using default
env variables,
k3_r5f_rproc r5f@5d00000: Invalid op: Trying to start secondary core 7 in lockstep mode
Load Remote Processor 3 with data@addr=0x82000000 83148 bytes: Failed!
Fix this by switching back both the clusters to the expected Split-mode.
Make this mode change in the u-boot specific dtsi file to avoid such
sync overrides in the future until the kernel dts is also switched to
Split-mode by default.
Fixes: fa09b12dc5 ("arm: ti: k3: Resync dts files and bindings with Linux Kernel v5.14")
Signed-off-by: Suman Anna <s-anna@ti.com>
There are a few memory functions for both the emif4 (AM3517)
and sdrc (OMAP35/DM37) code that can be defined as static,
because those functions are not used externally. Make them
static and clean up some of the corresponding headers.
Signed-off-by: Adam Ford <aford173@gmail.com>
With LTO enabled, some functions appear to be optimized in a
way that causes hanging on some OMAP3 boards after some
unrelated patches were applied. The solution appears to make
several functions __used. There also appears be to be some
dead code, so remove it while cleaning this up.
This has been tested on a general purpose OMAP3530, DM3730,
and AM3517.
Signed-off-by: Adam Ford <aford173@gmail.com>
Correct the min/max voltages of VDD_CPU. As per data sheet the VDD_CPU
minimum voltage is .6V & maximum voltage is .9V.
Correct the same. While at it fix the comment to reflect VDD_CPU
instead of VDD_MPU.
Data Sheet Link: https://www.ti.com/lit/gpn/dra829v
Signed-off-by: Keerthy <j-keerthy@ti.com>
Choose the memory map based on the compatible property from the
device tree passed to us by m1n1. Since DRAM on the M1 Pro/Max
starts at a different address avoid hardcoding the top of usable
memory. Also make sure that the addresses entered into the memory
map are page aligned such that we don't crash in dcache_enable().
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Tested on: Macbook M1 Max
Tested-by: Janne Grunau <j@jannau.net>
The commit 0dba45864b ("arm: Init the debug UART") calls
debug_uart_init() from crt0.S but it won't work because SOC is not
configured yet. That's why create board_debug_uart_init() which calls
psu_init() via new psu_uboot_init() earlier before the first access to UART
in SPL. In full U-Boot call psu_uboot_init() only when
CONFIG_ZYNQMP_PSU_INIT_ENABLED is enabled.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/878dc2daaa8685346f889989fbfb98b2e44da7fb.1645104518.git.michal.simek@xilinx.com
ZYNQMP_PSU_INIT_ENABLED is called only when BOARD_EARLY_INIT_F is defined
that's why cover this dependency in Kconfig.
board_early_init_f() is only part related to
CONFIG_ZYNQMP_PSU_INIT_ENABLED which is disabled now that's why disable
BOARD_EARLY_INIT_F and also build board_early_init_f() only when
CONFIG_BOARD_EARLY_INIT_F is enabled.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/d89253ec1590cd513dcd4bfbedebae618bd6d605.1645104518.git.michal.simek@xilinx.com
ZYNQMP_PSU_INIT_ENABLED specifically saying that has connection to full
U-Boot not SPL that's why build psu_spl_init for SPL all the time.
Also disable ZYNQMP_PSU_INIT_ENABLED because it ends up in situation that
psu_init() is called twice which is wrong. By default only SPL should call
it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/bf1e5d9a163f8853c7d951ad42965114ab0b1f50.1645104518.git.michal.simek@xilinx.com
Add support for ethernet on the imx8mn-ddr4-evk.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
This function is used in nxp u-boot tree.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The GW7902 is based on the i.MX 8M Mini / Nano SoC featuring:
- LPDDR4 DRAM
- eMMC FLASH
- Gateworks System Controller
- LTE CAT M1 modem
- USB 2.0 HUB
- M.2 Socket with USB2.0, PCIe, and dual-SIM
- IMX8M FEC
- PCIe based GbE
- RS232/RS485/RS422 serial transceiver
- GPS
- CAN bus
- WiFi / Bluetooth
- MIPI header (DSI/CSI/GPIO/PWM/I2S)
- PMIC
To add support for the i.MX8M Nano GW7902:
- Add imx8mn-venice dts/defconfig/include
- Add imx8mn-gw7902 dts
- Add imx8mn-2gb lpddr4 dram configs
- Add misc support for IMX8M Nano SoC
- rename imx8mm-venice.c to venice.c as it is no longer imx8mm specific
- update README with differences for IMX8MN vs IMX8MM
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The interface for NOR/OneNAND is called "EIM" not "EMI". Fix this.
Signed-off-by: Harald Seiler <hws@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
- a37xx: pci: Cleanup and minor fix for root port check (Pali)
- pci: mvebu: Ensure that root port is always on root zero bus (Pali)
- kwbimage: Fix dumping DATA registers for v0 images (Pali)
- kwbimage: Support for parsing extended v0 format (Pali)
- a37xx: Fix code and update DTS files to upstream version (Pali)
- a37xx: Fix and extend building memory map (Pali)
- ddr: marvell: a38x: fix BYTE_HOMOGENEOUS_SPLIT_OUT decision (Marek)
- mvebu: Optionally reset board on DDR training failure (Marek)
Some boards may occacionally fail DDR training. Currently we hang() in
this case. Add an option that makes the board do an immediate reset in
such a case, so that a new training is tried as soon as possible,
instead of hanging and possibly waiting for watchdog to reset the board.
(If the DDR training fails while booting the image via UART, we will
still hang - it doesn't make sense to reset in such a case, because
after reset the board will try booting from another medium, and the
UART booting utility does not expect that.)
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Function is named build_mem_map, not a3700_build_mem_map.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
In function build_mem_map() prepare also mapping for CCI-400 and
BootROM windows.
BootROM window is 1 MB long and by default starts at address 0xfff00000.
A53 AP BootROM is 16 kB long and repeats in this BootROM window 64 times.
RVBAR_EL3 register is set to value 0xffff0000, so by default A53 AP BootROM
is accessed via range 0xffff0000-0xffff3fff.
CCI-400 window when new TF-A version is used, starts at address 0xfe000000
and when old TF-A version is used, starts at address 0xd8000000.
Physical addresses are read directly from mvebu registers, so if TF-A
remaps it in future (again) then it would not cause any issue for U-Boot.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Function build_mem_map() modifies global variable mem_map. This variable is
used by the get_page_table_size() function which is called by function
arm_reserve_mmu() (as aliased macro PGTABLE_SIZE). Function
arm_reserve_mmu() is called earlier than enable_caches() which calls
build_mem_map(). So arm_reserve_mmu() does not calculate reserved memory
correctly.
Fix this issue by calling build_mem_map() from a3700_dram_init() which is
called before arm_reserve_mmu().
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
This change updates all Armada 37xx DTS files to version which is used by
Linux kernel v5.18.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Official DT bindings for Espressobin have disabled eMMC node.
As U-Boot requires to have this node enabled by default, do it in
armada-3720-espressobin-u-boot.dtsi DTS file.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
U-Boot specific changes should be in armada-3720-espressobin-u-boot.dtsi DTS file.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
In Linux kernel version of armada-37xx.dtsi file sdhci1 pointer refers to
sdhci@d0000 node and sdhci0 pointer to sdhci@d8000 node.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Official DT bindings have only one reg property: watchdog address space.
Convert armada-37xx-wdt.c driver to offical DT bindings and access sel_reg
register via MVEBU_REGISTER() macro, as its value (required by U-Boot
driver) is not in DT yet. In later stage can be driver cleaned to not use
it.
This change would allow U-Boot to use A3720 watchdog DTS structure from
Linux kernel.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Official DT bindings use compatible string marvell,armada-3700-ehci.
Update drivers and DTS files.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
In commit d368e10705 ("phy: marvell: a3700: Convert to official DT
bindings in COMPHY driver") was done update to official DT bindings but
compatible string of official DT bindings was not updated.
Fix it now.
Fixes: d368e10705 ("phy: marvell: a3700: Convert to official DT bindings in COMPHY driver")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
A new lpddr4 configuration is introduced for J7 SK with 4266 MTs data
rate. Therefore, update the R5 DTS file to point to the new DDR config
file.
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
EMIF tool for J721E SK is now updated to 0.6.1 that includes
* Updated write DQ training pattern to enable user pattern and clock
pattern (from 0x7 to 0x6).
* Updated IO drive strength to 40-80-80 Ohms.
J721E SK uses the lpddr4 configuration of 4266 MTs data rate which is
the same as J721E EVM but facing random failures. As the tool update is
specific to the SK board, add a new lpddr4 config of 4266 MTs.
Signed-off-by: Kevin Scholz <k-scholz@ti.com>
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
J721E Starter Kit (SK)[1] is a low cost, small form factor board designed
for TI’s J721E SoC. TI’s J721E SoC comprises of dual core A72, high
performance vision accelerators, video codec accelerators, latest C71x
and C66x DSP, high bandwidth real-time IPs for capture and display, GPU,
dedicated safety island and security accelerators. The SoC is power
optimized to provide best in class performance for industrial and
automotive applications.
J721E SK supports the following interfaces:
* 4 GB LPDDR4 RAM
* x1 Gigabit Ethernet interface
* x1 USB 3.0 Type-C port
* x3 USB 3.0 Type-A ports
* x1 PCIe M.2 E Key
* x1 PCIe M.2 M Key
* 512 Mbit OSPI flash
* x2 CSI2 Camera interface (RPi and TI Camera connector)
* 40-pin Raspberry Pi GPIO header
Add A72 specific dts for J721E-SK.
[1] https://www.ti.com/tool/SK-TDA4VM
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Board ID I2C EEPROM will be probed before SYSFW is available.
So drop the power-domains property for wakup_i2c0 on which
board ID EEPROM is connected.
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Enable support for selecting DTB from FIT within SPL based on the
board name read from EEPROM. This will help to use single defconfig
for both EVM and SK.
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
The changes introduced with commit 6337d53fdf ("arm: dts: sync am33xx
with Linux 5.9-rc7") prevent the PDU001 from operating correctly.
This patch fixes the configuration of the pin multiplexer and uart3.
Signed-off-by: Felix Brack <fb@ltec.ch>
EMIF tool for AM64 SK is now updated to 0.8.0 that includes
* disabled Write DQ training
* improve CA ODT to 60 ohms
The lpddr4 enabled with periodic WDQ training is causing periodic 26us
stall. This makes the SoC stall without doing anything which leads to
R5 interrupt latency in TCM memory. Due to this periodic training there
are some outstanding CPU transactions waiting for the lpddr4 to complete.
Hence, disable the periodic write DQ training during the
non-initialization stage of lpddr4 which results in an approximate 1us
stall. Also, update the lpddr4 config to improve CA ODT by 60 ohms
The rationales are as follows:
- PI_WDQLVL_EN: 2 Bits register field to support write DQ leveling,
disable bit 1 that supports Write DQ during non-initialization to
avoid ~26us stall during code execution.
- MR11_DATA_F1/F2_x register fields value changed to 0x66 that changes
the CA ODT from 48ohm to 60ohm to improve the eye margin on CA bus by
increasing the signal swing.
Signed-off-by: James Doublesin <doublesin@ti.com>
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Add a driver for the SPI controller integrated on Apple SoCs.
This is necessary to support the keyboard on Apple Silicon laopts
since their keyboard uses an Apple-specific HID over SPI protocol.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested on: Macbook Air M1
Tested-by: Simon Glass <sjg@chromium.org>
The power management controller found on Apple SoCs als provides
a way to reset all devices within a power domain. This is needed
to cleanly shutdown the NVMe controller before we hand over
control to the OS.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested on: Macbook Air M1
Tested-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Most Apple IOPs run a firmware that is based on what Apple calls
RTKit. RTKit implements a common mailbox protocol. This code
provides an implementation of the AP side of this protocol,
providing a function to initialize RTKit-based firmwares as well
as a function to do a clean shutdown of this firmware.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested on: Macbook Air M1
Tested-by: Simon Glass <sjg@chromium.org>
U-Boot is expected to support multiple generations of Apple SoCs
in a single binary with a single defconfig. Therefore it makes
more sense to set SYS_SOC to "apple".
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
This mailbox driver provides a communication channel with the
Apple IOP controllers found on Apple SoCs. These IOP controllers
are used to implement various functions such as the System
Manegement Controller (SMC) and NVMe storage. It allows sending
and receiving a 96-bit message over a single channel.
The header file with the struct used for mailbox messages is taken
straight from Linux.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested on: Macbook Air M1
Tested-by: Simon Glass <sjg@chromium.org>
When building for a custom board, it is quite common to maintain a
private branch which include some defconfig and .dts files. But to
hook up those .dts files requires modifying a file "belonging" to
upstream U-Boot, the arch/*/dts/Makefile. Forward-porting that branch
to a newer upstream then often results in a conflict which, while it
is trivial to resolve by hand, makes it harder to have a CI do "try to
build our board against latest upstream".
The .config usually includes information on precisely what .dtb(s) are
needed, so to avoid having to modify the Makefile, simply add the
files in (SPL_)OF_LIST to dtb-y.
A technicality is that (SPL_)OF_LIST is not always defined, so rework
the Kconfig symbols so that (SPL_)OF_LIST is always defined (when
(SPL_)OF_CONTROL), but only prompted for in the cases which used to be
their "depends on".
nios2 and microblaze already have something like this in their
dts/Makefile, and the rationale in commit 41f59f6853 is similar to
the above. So this simply generalizes existing practice. Followup
patches could remove the logic in those two makefiles, just as there's
potential for moving some common boilerplate from all the
arch/*/dts/Makefile files to the new scripts/Makefile.dts.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SCSI_AHCI_PLAT
CONFIG_SYS_SCSI_MAX_SCSI_ID
CONFIG_SYS_SCSI_MAX_LUN
CONFIG_SYS_SATA_MAX_DEVICE
Drop CONFIG_SCSI for everything except the sandbox build. We only need
one build for tests.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This is defined based on two other CONFIGs for all boards except sandbox
and durian.
For sandbox the value does not matter. For durian the value seems
excessive.
Drop the option completely, to simplify configuration and reduce the
number of things we need to convert to Kconfig.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This converts the following to Kconfig:
CONFIG_SYS_IDE_MAXBUS
CONFIG_SYS_IDE_MAXDEVICE
CONFIG_SYS_ATA_BASE_ADDR
CONFIG_SYS_ATA_STRIDE
CONFIG_SYS_ATA_DATA_OFFSET
CONFIG_SYS_ATA_REG_OFFSET
CONFIG_SYS_ATA_ALT_OFFSET
CONFIG_SYS_ATA_IDE0_OFFSET
CONFIG_SYS_ATA_IDE1_OFFSET
CONFIG_ATAPI
CONFIG_IDE_RESET
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This is supposed to be a build-system flag. Move it there so we can
define it before linux/kconfig.h is included.
Signed-off-by: Simon Glass <sjg@chromium.org>
The PLL_CMNLC clocks are modelled as a child clock device of seirra. In the
function device_probe, the corresponding clocks are probed before calling
the device's probe. The PLL_CMNLC mux clock can only be created after the
device's probe. Therefore, move assigned-clocks and assigned-clock-parents
to the link nodes in U-Boot device tree file.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
First check the presence of the ipu firmware in the boot partition.
If present enable the ipu and the related clocks & then move
on to load the firmware and eventually start remoteproc IPU1/IPU2.
do_enable_clocks by default puts the clock domains into auto
which does not work well with reset. Hence adding do_enable_ipu_clocks
function.
Signed-off-by: Keerthy <j-keerthy@ti.com>
[Amjad: fix IPU1_LOAD_ADDR and compile warnings]
Signed-off-by: Amjad Ouled-Ameur <aouledameur@baylibre.com>
J721S2 can support two instances for DDR. Therefore, add the device support
for the same and use 4266MT/s as DDR frequency.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
The EVM architecture for J721S2 is similar to that of J721E and J7200. It
is as follows,
+------------------------------------------------------+
| +-------------------------------------------+ |
| | | |
| | Add-on Card 1 Options | |
| | | |
| +-------------------------------------------+ |
| |
| |
| +-------------------+ |
| | | |
| | SOM | |
| +--------------+ | | |
| | | | | |
| | Add-on | +-------------------+ |
| | Card 2 | | Power Supply
| | Options | | |
| | | | |
| +--------------+ | <---
+------------------------------------------------------+
Common Processor Board
Common Processor board is the baseboard that contains most of the actual
connectors, power supply etc. The System on Module (SoM) is plugged on to
the common processor baord. Therefore, add support for peripherals brought
out in the common processor board.
Link to Common Processor Board: https://www.ti.com/lit/zip/sprr439
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
A System on Module (SoM) contains the SoC, PMIC, DDR and basic high speed
components necessary for functionality. Therefore, add support for the
components present on the SoM.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
The J721S2 SoC belongs to the K3 Multicore SoC architecture platform,
providing advanced system integration in automotive ADAS applications and
industrial applications requiring AI at the network edge. This SoC extends
the Jacinto 7 family of SoCs with focus on lowering system costs and power
while providing interfaces, memory architecture and compute performance for
single and multi-sensor applications.
Some highlights of this SoC are:
* Dual Cortex-A72s in a single cluster, three clusters of lockstep capable
dual Cortex-R5F MCUs, Deep-learning Matrix Multiply Accelerator(MMA), C7x
floating point Vector DSP.
* 3D GPU: Automotive grade IMG BXS-4-64
* Vision Processing Accelerator (VPAC) with image signal processor and
Depth and Motion Processing Accelerator (DMPAC)
* Two CSI2.0 4L RX plus one eDP/DP, two DSI Tx, and one DPI interface.
* Two Ethernet ports with RGMII support.
* Single 4 lane PCIe-GEN3 controllers, USB3.0 Dual-role device subsystems,
* Up to 20 MCANs, 5 McASP, eMMC and SD, OSPI/HyperBus memory controller,
QSPI, I3C and I2C, eCAP/eQEP, eHRPWM, MLB among other peripherals.
* Hardware accelerator blocks containing AES/DES/SHA/MD5 called SA2UL
management.
See J721S2 Technical Reference Manual (SPRUJ28 – NOVEMBER 2021)
for further details: http://www.ti.com/lit/pdf/spruj28
Introduce basic support for the J721S2 SoC.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
This adds initial support for the Toradex Verdin iMX8M Plus Quad 4GB WB
IT V1.0B module. They are strapped to boot from eFuses which are factory
fused to properly boot from their on-module eMMC. U-Boot supports
booting from the on-module eMMC only, SDP support is disabled for now
due to missing i.MX 8M Plus USB support.
Functionality wise the following is known to be working:
- eMMC, 8-bit and 4-bit MMC/SD card slots
- Ethernet both on-module eQoS and FEC (requires PHY on carrier board)
- GPIOs
- I2C
Boot sequence is:
SPL ---> ATF (TF-A) ---> U-boot proper
ATF, U-boot proper and u-boot.dtb images are packed into a FIT image,
loaded by SPL.
Boot:
U-Boot SPL 2022.04-rc1-00164-g21a0312611-dirty (Feb 07 2022 - 11:34:04 +0100)
Quad die, dual rank failed, attempting dual die, single rank configuration.
Normal Boot
WDT: Started watchdog@30280000 with servicing (60s timeout)
Trying to boot from BOOTROM
Find img info 0x&48025a00, size 872
Need continue download 1024
Download 779264, Total size 780424
NOTICE: BL31: v2.2(release):rel_imx_5.4.70_2.3.2_rc1-5-g835a8f67b
NOTICE: BL31: Built : 16:52:37, Aug 26 2021
U-Boot 2022.04-rc1-00164-g21a0312611-dirty (Feb 07 2022 - 11:34:04 +0100)
CPU: Freescale i.MX8MP[8] rev1.1 at 1200 MHz
Reset cause: POR
DRAM: 8 GiB
Core: 78 devices, 18 uclasses, devicetree: separate
WDT: Started watchdog@30280000 with servicing (60s timeout)
MMC: FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... OK
In: serial
Out: serial
Err: serial
Model: Toradex Verdin iMX8M Plus Quad 4GB Wi-Fi / BT IT V1.0B, Serial# 06817281
Carrier: Toradex Verdin Development Board V1.1A, Serial# 10807609
Setting variant to wifi
Net: Hard-coding pdata->enetaddr
eth1: ethernet@30be0000, eth0: ethernet@30bf0000 [PRIME]
Hit any key to stop autoboot: 0
Verdin iMX8MP #
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Update to the 5.16 imx8mq dts files and dt bindings
Changes since v1:
Dropped rfkill.h that is not in linux mainline yet.
Signed-off-by: Angus Ainslie <angus@akkea.ca>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Commit 97c16dc8bf ("imx: mx6ull: update the REFTOP_VBGADJ setting")
made this macro unused. Then remove it.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The previous code wrote the contents of the fuse as is in the
REFTOP_VBGADJ[2:0], but this was wrong if you consider the contents of
the table in the code comment. This table is also different from the
table in the commit description. But then, which of the two is correct?
If it is assumed that an unprogrammed fuse has a value of 0 then for
backward compatibility of the code REFTOP_VBGADJ[2:0] must be set to
6 (b'110). Therefore, the table in the code comment can be considered
correct as well as this patch.
Fixes: 97c16dc8bf ("imx: mx6ull: update the REFTOP_VBGADJ setting")
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Add the PCIe support on i.MX8MM platforms.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Tim Harvey <tharvey@gateworks.com>
Tested-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Marek Vasut <marex@denx.de> # Pick from Linux 854a4766ac12 ("arm64: dts: imx8mm: Add the pcie support")
Add the PCIe PHY support on iMX8MM platforms.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Tim Harvey <tharvey@gateworks.com>
Tested-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Marek Vasut <marex@denx.de> # Pick from Linux b9ec888f636f ("arm64: dts: imx8mm: Add the pcie phy support")
Fix address of the pad control register
(IOMUXC_SW_PAD_CTL_PAD_SD1_DATA0) for SD1_DATA0_GPIO2_IO2. This seems
to be a typo but it leads to an exception when pinctrl is applied due to
wrong memory address access.
Signed-off-by: Oliver Stäbler <oliver.staebler@bytesatwork.ch>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Fixes: c1c9d41319c3 ("dt-bindings: imx: Add pinctrl binding doc for imx8mm")
Fixes: 748f908cc882 ("arm64: add basic DTS for i.MX8MQ")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Marek Vasut <marex@denx.de> # Picked from Linux 5cfad4f45806f ("arm64: dts: imx8mm/q: Fix pad control of SD1_DATA0")
Add PLL 1.4 GHz, 1.5 GHz, 1.6 GHz, 1.8 GHz options for iMX8M SoCs
in case they should be operated faster, e.g. to improve boot time.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Linux uses slightly different divider settings for the 1.2 GHz PLL
configuration, adjust the coefficients to match Linux.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
According to TRM for i.MX8M Nano and Plus, GPR10 register contains lock
bit for TZASC_ID_SWAP_BYPASS bit. This bit is required to be set in
order to avoid AXI bus errors when GPU is enabled on the platform.
TZASC_ID_SWAP_BYPASS bit is alread set for all imx8m applicable
derivatives, but is missing a lock settings to be applied.
Set the TZASC_ID_SWAP_BYPASS_LOCK bit for those derivatives which have
it implemented.
Since we're here, provide also names to bits from TRM instead of using
BIT() macro in the code.
Fixes: deca6cfbf5 ("imx8mn: set BYPASS ID SWAP to avoid AXI bus errors")
Fixes: a07c718129 ("imx8mp: set BYPASS ID SWAP to avoid AXI bus errors")
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Cc: Peng Fan <peng.fan@nxp.com>
With the updated device tree's having USB support, enable in
U-Boot. This also requires the addition of the imx8m power
domain, since the USB is gated by the power domain controller.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Resync the SOM and baseboar files with the device trees that will
be included in 5.17-RC1 when it's cut. This will improve pinmuxing
for USDHC1 and add USB functionality.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
As suggested in commit 028abfd9b1 ("imx8mm-evk: Generate a single
bootable flash.bin again") for imx8mm_evk, it is possible to produce
single bootable image via binman. This restores the original behavior in
distros, where only one boot container is used to create target image.
Perform similar adaptions in order to provide single bootable image for
imx8mn-ddr4-evk derivate.
Update documentation to drop additional step of copying u-boot.itb
Fixes: 353dfe4b43 ("imx8mn-ddr4-evk: switch to use binman")
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Rather than using odd implicit blob-ext naming, explicitly specify the
type to be of blob-ext and therefore also simplify the node naming.
Signed-off-by: Patrick Wildt <patrick@blueri.se>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Some of the nodes were named using a underscore, so rectify this and
consistenly use dashes.
Signed-off-by: Patrick Wildt <patrick@blueri.se>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
When using a board variant that selects the lvds specific dtb the
*.u-boot.dtsi file will not be included. To have a lvds dtb specific
u-boot.dtsi file move this part to a common board u-boot.dtsi file and
include this in the board base u-boot.dtsi and create an additional one
for the lvds variant.
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Add support of secondary boot address for imx8mn. The secondary
boot address is hardcoded in the fuse. The value is calculated
from there according to the following description:
The fuse IMG_CNTN_SET1_OFFSET (0x490[22:19]) is defined as follows:
- Secondary boot is disabled if fuse value is bigger than 10, n = fuse
value bigger than 10.
- n == 0: Offset = 4MB
- n == 2: Offset = 1MB
- Others & n <= 10 : Offset = 1MB*2^n
- For FlexSPI boot, the valid values are: 0, 1, 2, 3, 4, 5, 6, and 7.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Similar to what has been done before with c5437e5b for u-boot proper, we
enable the SMP bit for SPL as well. This is necessary when SDP booting
straight into Linux, i.e. falcon boot. When SDP boot mode is active, the
ROM code does not set this bit which makes the caches not work once
activated in Linux.
On an i.MX6ULL (528MHz), this reduces a minimal kernel's boot time into
an initramfs shell from ~6.1s down to ~1.2s.
Signed-off-by: Sven Schwermer <sven@svenschwermer.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Synchronize DH DHCOM DTs with Linux commit 25960cafa06e ("Linux 5.15.12").
There is no functional change to the resulting DTs. The imx6qdl-dhcom-pdk2.dtsi
had to be adjusted with additional headers, gpio.h, pwm.h, input.h, else
the DT cannot be compiled, the same change is likely necessary in Linux.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add labels to remaining anatop regulators, so their supplies can be
assigned in board DTs. This is similar to Linux kernel commit
93385546ba369 ("ARM: dts: imx6qdl-sabresd: Assign corresponding power supply for LDOs")
except it does not contain the unrelated sabresd changes.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Now the dts information corresponds to the one available in the kernel.
With this patch applied the 'mtd list' shows proper names and
offsets for MTD partitions.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
With the current configuration provided in mxsimage{-spl}.mx28.cfg the
size of SPL binary has been constrained to 32 KiB, due to "LOAD IVT"
command with 0x8000 offset.
The problem was that, the imx28 ROM takes the u-boot.sb and then
extracts from it the IVT header and places it on the 0x8000 OCRAM offset
overwriting any valid (i.e. loaded from eMMC or SPI-NOR) SPL code. This
bug was unnoticed as the overwrite size was just 32 bytes, so the
probability that some important code is altered was low.
However, in the XEA board (where the SPL size is ~39KiB), the overwritten
data was `(struct dm_spi_ops *) 0x800c <mxs_spi_ops>`, which is used
during the boot process.
As a result the SPL execution code hanged with "undefined instruction"
abort as callbacks (with wrong addresses) from it were called.
The fix is to change the OCRAM's offset where IVT is loaded to 0xE000,
so the SPL can grow up to ~57KiB (the maximal size of OCRAM memory
available is 0xE3FC).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
According to the i.MX6ULL Reference Manual, pad CSI_DATA07 may
have the ESAI_TX0 functionality, not ESAI_T0.
Also, NXP's i.MX Config Tools 10.0 generates dtsi with the
MX6ULL_PAD_CSI_DATA07__ESAI_TX0 naming, so fix it accordingly.
There are no devicetree users in mainline that use the old name,
so just remove the old entry.
Fixes: f8ca22b8de ("arm: dts: imx6ull: add pinctrl defines")
Reported-by: George Makarov <georgemakarov1@gmail.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Use imx6_src_get_boot_mode() instead of manually reading SBMR1. The
existing function has proper handling for software overrides of the
bootdevice which can happen, for example, when booting from an alternate
source using `bmode`.
Signed-off-by: Harald Seiler <hws@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The PDK2 board is capable of running both 100M and 1G ethernet. However,
the i.MX6 has only one ethernet MAC, so it is possible to configure
either 100M or 1G Ethernet. In case of 100M option, the PHY is on the
SoM and the signals are routed to a RJ45 port. For 1G the PHY is on
the PDK2 board with another RJ45 port. 100M and 1G ethernet use
different signal pins from the i.MX6, but share the MDIO bus.
This SoM board combination is used to demonstrate how to enable 1G
ethernet configuration.
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: Stefano Babic <sbabic@denx.de>
The FXL6408 GPIO expander manages critical devices,
including on-module USB hub. Configure the expander to
switch the USB hub into bypass mode, allowing to use
on-carrier-board USB hub.
Signed-off-by: Oleksandr Suvorov <cryosay@gmail.com>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Extension boards can be added to Compulab's iot-gate-imx8mm.
We implement extension board manager for detecting the extension
boards.
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: uboot-imx <uboot-imx@nxp.com>
Obatin the SoC current temperature in print_cpuinfo().
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The DDRLOCKED bit in CGC2 DDRCLK will auto lock up and down by HW
according to DDR DIV updating or DDR CLK halt status change. So DDR
PCC disable/enable will trigger the lock up/down flow. We
need wait until unlock to ensure clock is ready.
And before configuring the DDRCLK DIV, we need polling the DDRLOCKED
until it is unlocked. Otherwise writing ti DIV bits will not set.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This patch implements enable_adc1_clk() to enable or disable the ADC1
clock on i.MX8ULP.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Get the MAC address from fuse bank5 word 3 and 4. It has
MSB first at lowest address, so have a reverse order with other
iMX used in mac.c
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When LPAV is allocated to RTD, the LPAV won't be reset. So we have to
reset DCNano and MIPI DSI in u-boot before enabling the drivers
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The LPAV is not allocated to APD when dual boot, so LPAV won't
reset when APD is reset. We have to explicitly reset the DDR,
otherwise its initialization will fail.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
8ULP ROM should read the LPOSC trim BIAS fuse to fill the CGC0
LPOSCCTRL[7:0], but it writes a fixed value on A0.1 revision.
A0.2 will fix the issue in ROM. But A0.1 we have to workaround
it in SPL by setting LPOSCCTRL BIASCURRENT again.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Remove the freescale vendor name from CPU revision print to align
with other i.MX platforms
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The setting does not have effect because we should set it after
power on the PS16 for NIC AV.
So move it after upower_init which has powered on all PS
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
To avoid DCNANO underrun issue on high loading test, set its
read Qos on NIC_LPAV to highest
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The board use IO9 of PCA6416 on LPI2C0 and TPM0 for MIPI DSI MUX and
backlight. However the LPI2C0 and TPM0 are M33 resources, in this
patch we simply access them, but this is a temporary solution.
We will modify it when M33 FW changes to set MIPI DSI panel as default
path and enable backlight after reset.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add the DSI clock enable and disable with PCC reset used.
Add the LCD pixel clock calculation and configuration for DCNano
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Assign the PXP/HIFI4/EPDC to APD domain, otherwise APD not
able to receive interrupts from the modules.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When single boot, assign AP domain as the master domain of the LPAV.
Allocates LPAV master and slave resources like GPU, DCNano, MIPI-DSI
eDMA channel and eDMA request to APD
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
S400 enables RDC only when the DBD_EN is fused. Otherwise, the RDC
is allowed by all masters.
Current S400 has issue if the XRDC has released to A35, then A35 reset
will fail in ROM due to S400 fails to get XRDC.
So temp work around is checking the DBD_EN, if it is not fused, we
don't need to call release XRDC or TRDC.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Change boot device logic to also allow environment stored in fat and in
ext4 when booting from SD or from eMMC.
As the boot device check for SD and for eMMC was depending on
ENV_IS_IN_MMC being defined, change the ifdef blocks at env_get_location
to use IS_ENABLED instead for all modes, returning NOWHERE when no valid
mode is found.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Correct printf format for unsigned long long is %llx and not %llxx.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The imx28 uses following voltage supplies hierarchy:
VDD_5V (VDD_BAT) -> VDDIO -> VDDA -> VDDMEM
\-----> VDDD
One shall first enable DCDC on the parent source (VDDIO) and then
follow with its children.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add EA iMX7ULP COM board support for building SPL.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Force selecting features present in SoC i.MX7ULP.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Reviewed-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Return the root clock values for MXC_CSPI_CLK, MXC_I2C_CLK,
MXC_UART_CLK and MXC_QSPI_CLK.
At least for the I2C clock the missing support leads to a wrong
configured I2C frequency. The expected value is 100kHz but the resulting
value is about 1MHz.
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Non GMAC's MDIO pins should have slew rate disabled for R(G)MII modes. Set
them accordingly in DT.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Tested-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
This is the promised second part of the sunxi PR for 2022.04, albeit
technially outside of the merge window. We were working on this full
steam since the beginning of the year, and it deserves to be merged,
I think.
The main attraction is support for the F1C100s SoC, which sports a
venerable ARM926 core. Support for this SoC and the LicheePi Nano board
has been in Linux for years, and U-Boot patches were posted mid last
year already.
The new SoC using ARMv5 also means that the bulk of the new code should
not touch any existing boards, although we did some refactorings first,
of course, which actually cleans up some existing sunxi code.
Compile tested for all 160 sunxi boards, and briefly tested on BananaPi M1,
OrangePi Zero, Pine64 and Pine-H64. Tested by others on their boards,
including F1C100s and F1C200s devices.
Add device tree files for suniv and
Lichee Pi Nano it is a board based on F1C100s.
dt-bindings/dts are synced with 5.16.0
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Add support for the suniv architecture, which is newer ARM9 SoCs by
Allwinner. The design of it seems to be a mixture of sun3i, sun4i and
sun6i.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Add support for F1C100s internal dram controller.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This patch aims to add header files for the suniv.
The header files included add support for uart, and clocks.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Some Allwinner SoCs use ARM926EJ-S core.
Add Allwinner/sunXi specific code to ARM926EJ-S CPU dircetory.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Both armv7 and arm926ejs use this timer code so move it to mach-sunxi.
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The ARMv7 start code has support for saving some boot params at the
entry point, which is used by some SoCs to return to BROM.
Port this to ARM926EJ-S start code.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
When we added Allwinner SoC support to ARMv8, we needed to pull in an
implementation of lowlevel_init() calling the C function s_init(), as
sunxi required it as this time.
The last few patches got rid of this bogus requirement, and as sunxi was
still the only user, we can now remove this lowlevel_init.S from ARMv8
altogether.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Currently we do some magic "SRAM setup" MMIO writes in s_init(), copied
from the original BSP U-Boot. The comment speaks of this being required
before DRAM access gets enabled, but there is no indication that this
would actually be required that early.
Move this out of s_init(), into board_init_f(). Since this actually only
affects a very few older SoCs, the actual code goes into the cpu/armv7
directory, to move it out of the way for all other SoCs.
This also uses the opportunity to convert some #ifdefs over to the fancy
IS_ENABLED() macros used in actual C code.
We keep the s_init() stub around for now, since armv8's lowlevel_init
still relies on it.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
According to their TRMs, Cortex ARMv7 CPUs with SMP support require the
ACTLR.SMPEN bit to be set as early as possible, before any cache or TLB
maintenance operations are done. As we do those things still in start.S,
we need to move the SMPEN bit setting there, too.
This introduces a new ARMv7 wide symbol and code to set bit 6 in ACTLR
very early in start.S, and moves sunxi boards over to use that instead
of the custom code we had in our board.c file (where it was called
technically too late).
In practice we got away with this so far, because at this point all the
other cores were still in reset, so any broadcasting would have been
ignored anyway. But it is architecturally cleaner to do it early, and
we move a core specific piece of code out of board.c.
This also gets rid of the ARM_CORTEX_CPU_IS_UP kludge I introduced a few
years back, and moves the respective logic into the new Kconfig entry.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
So far all Allwinner based boards were doing some not-so-lowlevel-setup
in lowlevel's s_init() routine.
This includes the initial clock, timer and pinmux setup, among other
things. This is clearly out of the "absolute bare minimum to get started"
scope that lowlevel_init.S suggests for this function.
Since we have an SPL, which is called right after s_init(), move those
calls to our board_init_f() function. As we overwrite this only for
the SPL, this has the added benefit of not doing this setup *again*
shortly afterwards, when running U-Boot proper.
This makes gpio_init() to be called from the SPL only, so pull this code
into a CONFIG_SPL_BUILD protected part to avoid build warnings.
Reviewed-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
There is some code that tries to "reset" the SCTLR_ELx register early in
the boot process. The idea seems to be to guarantee some sane settings
that U-Boot actually relies on, for instance running in little-endian
mode, with the MMU off initially.
However the current code has multiple problems:
- For a start, no platform or config defines the symbol that would
enable that code.
- The code itself really only works if the bits that it tries to clear
are already cleared:
- If we run in big-endian mode initially, any previous loads would have
been wrong already. That applies to the (optional) relocation code,
but more prominently to the mask that it uses to clear those bits:
"ldr x1, =0xfdfffffa" looks innocent, but actually involves a memory
access to the literal pool, using the current endianness.
- If we run with the MMU enabled, we are probably doomed already. We
*could* hope that we are running with an identity mapping, but would
need to do some cache maintenance to avoid losing dirty cache lines.
- The idea of doing a read-modify-write of SCTLR is somewhat
questionable to begin with, because as the owner of the current
exception level we should initialise all bits of this register with a
certain fixed value.
- The code is unnecessarily complicated, and the function name is
misspelled.
While those problems *could* admittedly be fixed, the point that is does
not seem to be used at all at the moment tells me we should just remove
this code, and be it to not give a bad example.
If people care, I could introduce some proper SCTLR initialisation code.
We are about to work this out for the boot-wrapper[1] as we speak, but
apparently we got away without doing this in U-Boot ever since, so it
might not be worth the potential trouble.
[1] https://lore.kernel.org/linux-arm-kernel/20220114105653.3003399-7-mark.rutland@arm.com/
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Setting LINUX_KERNEL_IMAGE_HEADER=y attempts to include an ARM64 Linux
kernel image header at the start of both U-Boot proper and SPL binaries.
However, some definitions that the image header uses are not included by
the SPL linker script, resulting in a build error. Include them the way
they are included in U-Boot proper's linker script to fix the error.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
The commit in the Fixes: tag below broke traffic through switch ports
where the SERDES protocol requires in-band autoneg and this requirement
isn't described in the device tree: SGMII, QSGMII, USXGMII (with
2500Base-X, in-band autoneg isn't supported).
The LS1028A-QDS boards are not yet ready for syncing their device trees
with Linux, since Ethernet is missing there (but has been submitted):
https://lore.kernel.org/lkml/20211112223457.10599-11-leoyang.li@nxp.com/
When agreement is reached for the Ethernet support in Linux, there will
be a sync for these boards as well. For now, just enable in-band autoneg
to fix the breakage.
Fixes: e3789a7262 ("net: dsa: felix: configure the in-band autoneg property based on OF node info")
Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Allow device trees to be reused between Linux and U-Boot.
The source for these device trees is linux-next as of commit
bd8a9cd624c6 ("arm64: dts: ls1028a-rdb: update copyright"), which was
chosen because some changes needed to be done to the Linux DTs too,
before they could be shared:
https://lore.kernel.org/linux-arm-kernel/20211202141528.2450169-5-vladimir.oltean@nxp.com/T/#m6f63c92e75fa79a01144b2c2c6dc4776e7971395
There are two more commits on the RDB device tree which haven't been
picked up yet, because they have dependencies on the SoC device tree:
dd3d936a1b17 ("arm64: dts: ls1028a: add ftm_alarm1 node to be used as wakeup source")
b2e2d3e02fb6 ("arm64: dts: ls1028a-rdb: enable pwm0")
These will be picked up on the next resync.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reuse the scheme implemented by the Kontron SL28 boards in
commit d08011d7f9
("arm: dts: ls1028a: disable the PCIe controller by default")
and move the 'status = "okay"' lines for the PCIe controllers
inside a separate U-Boot dtsi for the LS1028A-RDB board. This way, the
existing Linux device tree can simply be dropped in.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
There is no I2C peripheral on these buses on the reference design board,
and the Linux device tree does not enable them either.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
There is no SPI peripheral on the LS1028A-RDB, therefore no reason to
enable these nodes in the U-Boot device tree (and Linux does not enable
them either).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
In a bit of a blunder, the blamed commit in the Fixes: tag below made
the mscc_felix switch driver look at the 'managed = "in-band-status"'
device tree property, forgetting that the U-Boot device tree had not
been updated to include that property, whereas the Linux one does.
The switch is therefore described in the device tree as not requiring
in-band autoneg, but the PHY driver for VSC8514 (drivers/net/phy/mscc.c)
still enables that feature. This results in a mismatch => no traffic.
This patch is a copy-paste of the Ethernet device tree nodes from Linux,
which resolves that issue. The device tree update also renames the
Ethernet PHY labels.
Fixes: e3789a7262 ("net: dsa: felix: configure the in-band autoneg property based on OF node info")
Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The nodes in the NXP LS1028A-RDB device tree are out of order, regroup
them alphabetically to have a simple delta when the Linux device tree is
brought in.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
During the LS1028A-RDB sync with Linux device trees, it was observed
that the same RTC is present on the two boards, and the wrong compatible
string is used in both places. This change updates the RTC from the
LX2160A-RDB to use the compatible string that was established in Linux.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: Michael Walle <michael@walle.cc>
During this board's sync with Linux device trees, it was observed that
it doesn't use the same compatible string for the RTC node as in U-Boot.
This change makes the RTC compatible strings match, for a smoother sync.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The LS1028A-QDS board won't be synced with the Linux device trees right
now, since those are currently still in progress (Ethernet is missing).
However, while we're at converting the RDB, it can be observed that the
same RTC is present on the two boards, and the wrong compatible string
is used in both places. This change updates the RTC from the QDS to use
the compatible string that was established in Linux.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: Michael Walle <michael@walle.cc>
During the LS1028A-RDB sync with Linux device trees, it was observed
that the same RTC is present on the two boards, and the wrong compatible
string is used in both places. This change updates the RTC from the
LX2160A-QDS to use the compatible string that was established in Linux.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: Michael Walle <michael@walle.cc>
During the LS1028A-RDB sync with Linux device trees, it was observed
that the same RTC is present on the two boards, and the wrong compatible
string is used in both places. This change updates the RTC from the
LS1088A-RDB to use the compatible string that was established in Linux.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: Michael Walle <michael@walle.cc>
During the LS1028A-RDB sync with Linux device trees, it was observed
that the same RTC is present on the two boards, and the wrong compatible
string is used in both places. This change updates the RTC from the
LS1088A-QDS to use the compatible string that was established in Linux.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Even not used by u-boot, this has to be inline with the hw and kernel dts.
U-boot partition table is defined by MTDPARTS_DEFAULT Kconfig.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Beside that mounted rgmii debug phy is 1000Mbps capable, the debug link
between the piggy board and the phy is 100Mbps only.
This leads to longer link establishment time when working in debug mode,
as phy tries to autoneg 1000Mbps.
This patch fixes the speed to 100Mbps and allows smother link establishment
time for the debug interface.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The Ten64 is a networking-oriented MiniITX board
using the NXP LS1088A SoC.
This patch provides the bare minimum to support
Ten64 boards under U-Boot for distroboot.
Some related drivers have not yet been submitted
and this basic support lacks some of the
opinionated defaults provided by our firmware
distribution.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Although it isn't known what bit 0 in PHY reg 8 does, it's obvious that
it has to be set before read calibration and cleared afterwards. This is
already done for first rank, but not for second (copy & paste error.)
Fix it.
Fixes: f4317dbd06 ("sunxi: Add H616 DRAM support")
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Kconfig symbol is missing CONFIG_ prefix, so compiler will always
skip ODT configuration.
Fix symbol name.
Fixes: f4317dbd06 ("sunxi: Add H616 DRAM support")
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
For sunxi boards with the AXP209, AXP221, AXP809, and AXP818 PMICs
(plus possibly others, I only confirmed the datasheets for these),
it is sometimes desirable to not boot whenever the device is
plugged in. An example would be when using the NTC CHIP inside a
PocketCHIP.
This provides a configurable option to check if bit 0 of
register 0 of the PMIC says it was powered because of a power button
press (0) or a plug-in event (1). If the value is 1 and this option
is selected, the device shuts down shortly after printing a message
to console stating the reason why it's shutting down. Powering up the
board with the power button is not affected.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
[Andre: reword to speak of boot, remove #ifdefs]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The calls for flipping bits in the Allwinner pin controller registers
were using unnecessarily complex pointer arithmetic.
Improve readability by simplifying the expression.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The GPIO and pinctrl drivers need these setters for pin configuration.
Since they are DM drivers, they should not be using hardcoded base
addresses. Factor out variants of the setter functions which take a
pointer to the GPIO bank's MMIO registers.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The return values of these functions are always zero, and they are
never checked. Since they are not needed, remove them.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
ROM supports cpsw_port2 for Ethernet boot and SPL stages continue to
download images on the same port, therefore there is no need to enable
cpsw_port1. Disable the same.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Since commit 9855034397 ("fdt: Don't call board_fdt_blob_setup()
without OF_BOARD") board_fdt_blob_setup() is no more called on
STM32MP platforms in trusted boot which hangs during boot process.
Enable OF_BOARD flag to fix this issue.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add the partition name and remove the line number in error messages
of treat_partition_list() to provide correct information to user of
STM32CubeProgrammer.
The "line number" value was confusing because it is incorrect here;
the index in part_array[] is not aligned with the line number in
the parsed Layout file, because the empty lines and the lines beginning
by '#' are skipped during the first parsing in parse_flash_layout().
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Synchronize DH DHCOM DTs with Linux commit 25960cafa06e ("Linux 5.15.12").
There is no functional change to the resulting DTs. The eeprom0 alias and
PHY reset GPIO are now reinstated in SoM u-boot dtsi.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Synchronize DH DHCOR DTs with Linux commit 25960cafa06e ("Linux 5.15.12").
There is no functional change to the resulting DTs. The eeprom0 alias is
now reinstated in SoM u-boot dtsi, the PHY reset GPIO is reinstated in AV96
u-boot dtsi.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Device tree alignment with Linux kernel v5.16-rc5
- ARM: dts: stm32: set otg-rev on stm32mp151
- ARM: dts: stm32: use usbphyc ck_usbo_48m as USBH OHCI clock on stm32mp151
- ARM: dts: stm32: fix AV96 board SAI2 pin muxing on stm32mp15
- ARM: dts: stm32: fix SAI sub nodes register range
- ARM: dts: stm32: fix STUSB1600 Type-C irq level on stm32mp15xx-dkx
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Default value for CONFIG_SYS_BOOTCOUNT_SINGLEWORD and
CONFIG_SYS_BOOTCOUNT_ADDR are only needed when
CONFIG_BOOTCOUNT_GENERIC is used.
This patch avoids to define these configs when an other bootcount backend
is activated, for example for CONFIG_BOOTCOUNT_ENV.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Today the bootcount is not managed by the Linux kernel for STM32MP15 as
we don't have driver to update the used backup register in TAMP and the
recovery command still executes the normal bootcmd with
'altbootcmd=run bootcmd'.
So the bootcount feature is never used, the config CONFIG_BOOTCOUNT_LIMIT
and the associated environment variable 'altbootcmd' can be removed to
reduce the U-Boot size.
Each boards can re-enable this feature later in their defconfig, if it is
needed, with the expected backend, for example CONFIG_BOOTCOUNT_GENERIC
or CONFIG_BOOTCOUNT_ENV.
CC: Marek Vasut <marex@denx.de>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This patch configures U-Boot SPL for DHCOR SoM to permit DFU upload of
SPL and subsequent u-boot.itb for recovery or commissioning purposes.
To start U-Boot on DHCOR based board, e.g. Avenger96, proceed as follows:
- Install dfu-util on the host PC (in debian this is package 'dfu-util')
- Power off the Avenger96 board.
- Connect both USB-serial console and USB-OTG microB ports to host PC.
- Switch Avenger96 to USB boot mode -- BOOT0..2 switches all set to 0.
- Power on the Avenger96 board.
- Verify using '$ dmesg' that a new device has been detected as follows:
New USB device found, idVendor=0483, idProduct=df11, bcdDevice= 2.00
New USB device strings: Mfr=1, Product=2, SerialNumber=3
Product: DFU in HS Mode @Device ID /0x500, @Revision ID /0x0000
Manufacturer: STMicroelectronics
- Upload U-Boot SPL:
$ dfu-util -a 1 -D u-boot-spl.stm32
- Upload U-Boot proper:
$ dfu-util -a 0 -D u-boot.itb
- At this point, SPL will wait for user to press "Ctrl-C" on serial
console. When ready to interact with U-Boot, press Ctrl-C to start
the bootloader.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
In case the SoC reports the boot device type is USB, it means the SPL was
loaded via BootROM DFU mode. Currently the spl_boot_device() returns boot
device as USB host, change it to DFU instead, so the SPL can continue the
DFU boot and load U-Boot via DFU.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
When booting from QSPI, the boot ROM appears to mux the QSPI
pins, but it's not guaranteed to be setup when booting from
eMMC. Fix this by explicitly configuring the pinmux.
Signed-off-by: Adam Ford <aford173@gmail.com>
This converts the following to Kconfig:
CONFIG_AT91_EFLASH
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Eugen Hristev <eugen.hristev@microchip.com>
- fdt_support: Add fdt_for_each_node_by_compatible() helper macro
(Marek)
- turris_omnia: Fixup SATA or PCIe nodes at runtime in DT blob (Pali)
- pci_mvebu: Add support for Kirkwood PCIe controllers (Pali)
- SPL: More verifications for kwbimage in SPL (Pali)
- mvebu: Remove comphy_update_map() (Pali)
- Minor misc stuff
Use the preferred
if (IS_ENABLED(X))
instead of
#ifdef X
where possible.
There are still places where this is not possible or is more complicated
to convert in this file. Leave those be for now.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Checkpatch warns about using uint32/16/8_t instead of u32/16/8.
Use the preferred types.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Print the wrong srcaddr (spl_image->offset) in error message also for
SATA case.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Last 4 bytes of kwbimage boot image is checksum. Verify it via the new
spl_check_board_image() function which is called by U-Boot SPL after
loading kwbimage.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Each boot mode has its own kwbimage specified by blockid. So check that
kwbimage is valid by blockid.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Add parameter spl_boot_device to spl_parse_board_header(), which allows
the implementations to see from which device we are booting and do
boot-device-specific checks of the image header.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
There are certain restrictions for kwbimage offset and blocksize.
Validate them.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Kirkwood uses macros KW_DEFADR_PCI_MEM and KW_DEFADR_PCI_IO for base
address of PCIe mappings. Size of PCIe windows is not defined in any macro
yet, so export them in new KW_DEFADR_PCI_MEM_SIZE and KW_DEFADR_PCI_IO_SIZE
macros.
Kirkwood arch code already maps mbus windows for io and mem, so avoid
calling mvebu_mbus_add_window_by_id() function which would try to do
duplicate window mapping.
Kirkwood PCIe controllers already use "marvell,kirkwood-pcie" DT compatible
string, so mark pci_mvebu.c driver as compatible for it.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Add macro fdt_for_each_node_by_compatible() to allow iterating over
fdt nodes by compatible string.
Convert various usages of
off = fdt_node_offset_by_compatible(fdt, start, compat);
while (off > 0) {
code();
off = fdt_node_offset_by_compatible(fdt, off, compat);
}
and similar, to
fdt_for_each_node_by_compatible(off, fdt, start, compat)
code();
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
gpio:
- Add modepin driver
net:
- Save random mac addresses to eth variable
zynqmp gem:
- Add support for mdio bus DT description
- Add support for reset and SGMII phy configuration
- Reduce timeout for MDIO accesses
zynqmp clk:
- Fix clock handling for gem and usb
phy:
- Add zynqmp phy/serdes driver
serial:
- Add one missing compatible string
microblaze:
- Symbol alignement
- SPL fixups
- Code cleanups
zynqmp:
- Various dt changes, DP pre-reloc, gem resets, gem clocks
- Switch SOM to shared psu configuration
- Move dcache handling to firmware driver
- Workaround gmii2rgmii DT description issue
- Enable broadcasts again
- Change firmware enablement logic
- Small adjustement in firmware driver
versal:
- Support new mmc@ DT nodes
- Fix run time variable handling
- Add missing I2C_PMC ID for power domain
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYeg7sQAKCRDKSWXLKUoM
IVhJAKCAiNx/joEeFBJ0XgThtJzFhCjdMwCfYKY9Ewz4L0n2I56lDgR3UJroct0=
=HtB+
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.04-rc1' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2022.04-rc1
gpio:
- Add modepin driver
net:
- Save random mac addresses to eth variable
zynqmp gem:
- Add support for mdio bus DT description
- Add support for reset and SGMII phy configuration
- Reduce timeout for MDIO accesses
zynqmp clk:
- Fix clock handling for gem and usb
phy:
- Add zynqmp phy/serdes driver
serial:
- Add one missing compatible string
microblaze:
- Symbol alignement
- SPL fixups
- Code cleanups
zynqmp:
- Various dt changes, DP pre-reloc, gem resets, gem clocks
- Switch SOM to shared psu configuration
- Move dcache handling to firmware driver
- Workaround gmii2rgmii DT description issue
- Enable broadcasts again
- Change firmware enablement logic
- Small adjustement in firmware driver
versal:
- Support new mmc@ DT nodes
- Fix run time variable handling
- Add missing I2C_PMC ID for power domain
There are 4 MDIO bus controllers in AST2600 SOC. Each of them can
connect to one or more PHY chips and is flexible to work with the 4 MAC
devices in AST2600. On AST2600 EVB, MDIO 0,1,2,3 connect to the PHY
chips used by MAC 0,1,2,3 respectively.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
This patch adds node for mmc/sd controller found on Action Semi OWL
S700 SoC.
Since, upstream Linux binding has not been merged for S700 MMC/SD
controller, Changes are put in u-boot specific dtsi file.
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
This Synchronizes the Actions Semi S700 SoC DT changes from
commit "g58e1100fdc59" ("Linux v5.16-rc3").
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
asm/mmu.h include is currently guarded by CONFIG_ADDR_MAP ifdef because
the header is only present on arm and powerpc. In order to remove the
dependency on this header and the associated ifdef, move init_addr_map()
declaration to init.h, since it is only called during the common init
sequence.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Add a return value to init_addr_map and use it directly in the
post-relocation init sequence, rather than using a wrapper stub.
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Factor out armv7m fragment to spl_perform_fixups(), which is an arch/board
specific function designed for this purpose.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
- Let am335x_evm use the CPSW or PRUSS ethernet.
- Implement timer_get_boot_us in the omap timer driver
- gpmc bitflip, QSPI clock calculation on am437x, da8xx_gpio bugfixes
- Assorted K3 updates
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmHlNOccHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyL0JB/4+sKNWPMgOYvP2uLCC
euRGomhxJ5WmxJVDtJeBIRg0YKSkwnE8JwIN2qqGu15xJnNX9Ck5qnIMPbiZ/io9
ocW5Z/4C4rfJX/OzD6FtmbMNsvG/umVmZkjRU3ryRXKGyNVpVjLQ2EEECaJfk1WZ
Nd/J6/Jo8nafb1x4OeY+F6+xwZAuj7Mrun9SsDSyrIvmEqSnaQNioj+lStkauL51
NwQgBxZBQmbdCgF7Ooy6rYlXZBR6r/rgWB9n3RP8emDCwfCMul9HOMT432oKNbhW
bGrcMu9AWv/pgzXogxSzYbEdTAnoVEODtU1suCa8LV6KJPEG693gARnRm/KjvPHa
FfsK
=39IY
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2022.04-b' of https://source.denx.de/u-boot/custodians/u-boot-at91
Second set of u-boot-at91 features for the 2022.04 cycle:
This small feature set includes few changes for sama7g5 and sama7g5ek:
turn blue led on at boot, changes required for the Rev4 of the board,
better sync with the Linux DT with regards to the new DT nodes.
The rev4 of the board sama7g5ek has the eeproms on flexcom8 instead of
flexcom1.
Initialize flexcom8 with required pincontrol and move the eeproms accordingly.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Add Flexcom8 node with required referenced nodes as phandles.
Since Flexcom8 is present in Linux, take the node exactly as-is from Linux.
Some nodes are referenced in Linux as phandles, the dma and the gic.
Add them as well to the file, even if they are unused by Uboot.
This is a step towards having the U-boot DT equivalent with the DT in Linux.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
This driver supports power domains for the power management
controller found on Apple SoCs.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
These are necessary to make sure the power domains needed for the
serial console are availble in the pre-relocation phase.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This synchronizes the device trees with those that are in the
process of being upstreamed into Linux. This is mostly the
current state of the device trees on the asahilinux branch
with a few extra bits used by OpenBSD. This includes device
trees for machines that were still missing.
There are still some differences that will hopefully be resolved
soon.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Probe toplevel AM65 CPSW NUSS driver from misc_init_r() when driver
is enabled. Since driver is modeled as UCLASS_MISC, we need to
explicitly probe the driver. Use common misc_init_r() that entire
K3 family of SoCs.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
In case of xSPI bootmode OSPI flash is in DDR mode and needs to be accessed
in multiple of 16bit accesses Hence we cannot parse sysfw.itb FIT image
directly on OSPI flash via MMIO window. So, copy the image to internal
on-chip RAM before parsing the image.
Moreover, board cfg data maybe modified by ROM/TIFS in case of HS platform
and thus cannot reside in OSPI/xSPI and needs to be copied over to
internal OCRAM.
This unblocks OSPI/xSPI boot on HS platforms
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Dave Gerlach <d-gerlach@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Currently only the PADCFG registers of the main domain are unlocked.
Also unlock PADCFG registers of MCU domain, so MCU pin muxing can be configured by u-boot or Linux.
Signed-off-by: Michael Liebert <liebert@ibv-augsburg.de>
Tested-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Acked-by: Nishanth Menon <nm@ti.com>
Documentation:
* Fix building HTML documentation of readthedocs.io
* Add ARM Juno board documentation
* Build requirements for Alpine Linux
* Include DM headers in API documentation
UEFI:
* Fix section alignment of EFI binaries
* Fix header length of RISC-V EFI binaries allowing to run them on EDK II
* Remove kaslr-seed from device tree if the EFI_RNG_PROTOCOL is provided
Other:
* Let 'part list' show all 128 GPT partitions
-----BEGIN PGP SIGNATURE-----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=NZ+6
-----END PGP SIGNATURE-----
Merge tag 'efi-2022-04-rc1' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2022-04-rc1
Documentation:
* Fix building HTML documentation of readthedocs.io
* Add ARM Juno board documentation
* Build requirements for Alpine Linux
* Include DM headers in API documentation
UEFI:
* Fix section alignment of EFI binaries
* Fix header length of RISC-V EFI binaries allowing to run them on EDK II
* Remove kaslr-seed from device tree if the EFI_RNG_PROTOCOL is provided
Other:
* Let 'part list' show all 128 GPT partitions
The alignment of sections in the EFI binaries generated by U-Boot is
incorrect.
According to the PE-COFF specification [1] the minimum value for
FileAlignment is 512. If the value of SectionAlignment is
less then the page size, it must equal FileAlignment.
Let's set both values to 512 for the ARM and RISC-V architectures.
[1] https://docs.microsoft.com/en-us/windows/win32/debug/pe-format
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Apple's ARMv8 cores don't implement EL3 and therefore don't
provide a PSCI implementation. So don't attempt to use
PSCI to reset on machines using Apple SoCs.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
BootROMs on pre-A38x SoCs enabled its output on UART by default, but A38x'
BootROM has its output on UART disabled by default.
To enable BootROM output on A38x SoC, it is required to set DEBUG flag
(which only enables BootROM output and nothing more) in kwbimage. For UART
images this DEBUG flag is ignored by BootROM.
Enable kwbimage DEBUG flag for all A38x boards.
With this change BootROM prints the following (success) information on UART
before booting U-Boot kwbimage:
BootROM - 1.73
Booting from SPI flash
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
U-Boot SPL for mvebu platform is not compiled as position independent.
Therefore it is required to instruct BootROM to load U-Boot SPL at the
correct address. Loading of kwbimage binary code at specific address can be
now achieved by the new LOAD_ADDRESS token as part of BINARY command in
kwbimage config file.
Update mvebu Makefile to put value of $(CONFIG_SPL_TEXT_BASE) into
LOAD_ADDRESS token when generating kwbimage.cfg from kwbimage.cfg.in.
It is required to update regex for sed to find replacement tokens at any
position on a line in kwbimage config file and not only at the beginning of
the line. This is because LOAD_ADDRESS is specified at the end of line
containing the BINARY command.
It looks like all Armada boards set CONFIG_SPL_TEXT_BASE to value
0x40004030 or 0x40000030. Why this value? It is because main kwbimage
header is at address 0x40004030 or 0x40000000 and it is 32 bytes long.
After the main header there is the binary header, which consist of 1 byte
for type, 3 bytes for size, 1 byte for number of arguments, 3 reserved
bytes and then 4 bytes for each argument. After these arguments comes the
executable code.
So arguments start at address 0x40004028 or 0x40000028. Before commit
e6571f38c9 ("arm: mvebu: Remove dummy BIN header arguments for SPL
binary") there were two (dummy) arguments, which resulted in load address
of 0x40004030 or 0x40000030, always. After that commit (which removed dummy
arguments), load address stayed same due to the 128-bit alignment done by
mkimage.
This patch now reflects the dependency between $(CONFIG_SPL_TEXT_BASE),
load address and dummy kwbimage arguments, and allows the user to adjust
$(CONFIG_SPL_TEXT_BASE) config option to some other value.
For unsupported values, when mkimage/kwbimage cannot set chosen load address
as specified by $(CONFIG_SPL_TEXT_BASE), the build process now fails,
instead of silently generating non-working kwbimage.
Removal of this alignment between $(CONFIG_SPL_TEXT_BASE) and LOAD_ADDRESS
can only be done by compiling U-Boot SPL as position independent. But this
currently is not possible for 32-bit ARM version of U-Boot SPL.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Usage of $(call cmd,...) is standard way to call other commands which
generate things.
It also has the advantage of printing build information in the form
KWBCFG arch/arm/mach-mvebu/kwbimage.cfg
if verbosity is disabled, and printing the build command otherwise.
Note that the '#' character needs to be escaped in Makefile when used as
value for make variable assignment.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
The DT properties for the "enable-arbiter" and "keep-config" config
knobs were previously named inconsistently:
- The u-boot driver used "nand-enable-arbiter" and "nand-keep-config"
names, without Marvell prefixes.
- The Linux driver uses "marvell,nand-keep-config" ("enable-arbiter"
does not exist anymore in recent kernels, but it also used to be
"marvell,nand-enable-arbiter").
- The device trees almost all use "marvell," prefixed names, except for
one single instance of "nand-enable-arbiter" without vendor prefix.
This commit standardizes on the vendor prefixed version, making the
u-boot driver read from DT props "marvell,nand-enable-arbiter" and
"marvell,nand-keep-config". The one device tree using the unprefixed
version is also changed to use the new naming.
This has the side effect of making the previously no-op "marvell,"
config knobs already present in some DTs actually do something. This was
likely the original intention of the DT authors, but note that this
commit was not tested on every single impacted board.
Signed-off-by: Pierre Bourdon <delroth@gmail.com>
As explained in commit 3bedbcc3aa ("arm: mvebu: a38x: serdes: Don't
overwrite read-only SAR PCIe registers") it is required to set Maximum Link
Width bits of PCIe Root Port Link Capabilities Register depending of number
of used serdes lanes. As this register is part of PCIe address space and
not serdes address space, move it into pci_mvebu.c driver.
Read number of PCIe lanes from DT property "num-lanes" which is used also
by other PCIe controller drivers in Linux kernel. If this property is
absent then it defaults to 1. This property needs to be set to 4 for every
mvebu board which use PEX_ROOT_COMPLEX_X4 or PEX_BUS_MODE_X4.
Enabling of PCIe port needs to be done afer all registers in PCIe address
space are properly configure. For this purpose use new mvebu-reset driver
(part of system-controller) and remove this code from serdes code.
Because some PCIe ports cannot be enabled individually, it is required to
first setup all PCIe ports and then enable them.
This change contains also all required "num-lanes" and "resets" DTS
properties, to make pci_mvebu.c driver work correctly.
Signed-off-by: Pali Rohár <pali@kernel.org>
Enabling and disabling PCIe ports is done via address space of system
controller. All 32-bit Armada SoCs use low 4 bits in SoC Control 1 Register
for enabling and disabling some or more PCIe ports. Correct mapping needs
to be set in particular DTS files.
DT API for mvebu-reset is prepared for implementing resets also for other
HW blocks, but currently only PCIe is implemented via index 0.
Currently this driver is not used as PCIe ports are automatically enabled
by SerDes code executed by U-Boot SPL. But this will change in followup
patches.
Signed-off-by: Pali Rohár <pali@kernel.org>
Do not call pci_set_region() for resources which were not properly mapped.
This prevents U-Boot to access unmapped memory space.
Update MBUS_PCI_MEM_SIZE and MBUS_PCI_IO_SIZE macros to cover all PCIe MEM
and IO ranges. Previously these macros covered only address ranges for the
first PCIe port. Between MBUS_PCI_IO_BASE and MBUS_PCI_MEM_BASE there is
space for six 128 MB long address ranges. So set MBUS_PCI_MEM_SIZE to value
of 6*128 MB. Similarly set MBUS_PCI_IO_SIZE to 6*64 KB.
Function resource_size() returns zero when start address is 0 and end
address is -1. So set invalid resources to these values to indicate that
resource has no mapping.
Split global PCIe MEM and IO resources (defined by MBUS_PCI_*_* macros)
into PCIe ports in mvebu_pcie_bind() function which allocates per-port
based struct mvebu_pcie, instead of using global state variables
mvebu_pcie_membase and mvebu_pcie_iobase. This makes pci_mvebu.c driver
independent of global static variables (which store the state of
allocation) and allows to bind and unbind the driver more times.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
The only user of board_pex_config() weak function is A385 controlcenterdc
board. It looks like that code in its board_pex_config() function needs to
be executed after PCIe link is up. Therefore put this code into
spl_board_init() function which is called after a38x serdes initialization,
and therefore it is after the serdes hws_pex_config() function finishes
(which is the state before this change).
With this change completely remove board_pex_config() function as it is not
used anymore.
Signed-off-by: Pali Rohár <pali@kernel.org>
Rely on the new watchdog timer driver and the sysreset uclass to
reset the system. This gets rid of hard-coded addresses and
should work on systems based on the new M1 Pro and M1 Max SoCs
as well.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-on: Apple M1 Macbook
Tested-by: Simon Glass <sjg@chromium.org>
Add a node for the watchdog timer based on the proposed Linux
device tree bindings.
Remove the old reboot node which was a watchdog timert node in
disguise using a preliminary device tree binding.
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-on: Apple M1 Macbook
Tested-by: Simon Glass <sjg@chromium.org>
a7y17lte is called SM-A720F, and a3y17lte SM-A320F. a3y17lte also
should select PINCTRL_EXYNOS78x0, not the (non-existent)
PINCTRL_EXYNOS7880, and it has an Exynos 7870 SoC and not 7880.
Fixes: 3e2095e960 ("board: samsung: add support for Galaxy A series
of 2017 (a5y17lte)")
Signed-off-by: Henrik Grimler <henrik@grimler.se>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
- meson64_android: add board specific env settings, in order to support VIM3/L for android
- add changes to support VIM3/L android boot by using meson64_android.h config
-----BEGIN PGP SIGNATURE-----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=dLEg
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20220107' of https://source.denx.de/u-boot/custodians/u-boot-amlogic into next
- disable CONFIG_NET_RANDOM_ETHADDR when unnecessary on amlogic based configs
- meson64_android: add board specific env settings, in order to support VIM3/L for android
- add changes to support VIM3/L android boot by using meson64_android.h config
All i.MX8MQ boards have been converted to binman, which makes it
necessary to flash both flash.bin and u-boot.itb to get a bootable
system. Prior to the conversion, only flash.bin was needed.
Such new requirement breaks existing distro mechanisms to generate the
final binary because the extra u-boot.itb is now required.
Generate a final flash.bin that can be used again as a single bootable
binary to keep the original behavior.
After this change the SPL binary is called spl.bin, which is a more
descriptive name for its purpose, and can still be used standalone (for
example, for secure boot purposes).
Also update imx8mq_evk.rst to remove the u-boot.itb copy step.
This is a cherry-pick of 028abfd9b1 ("imx8mm-evk: Generate a single
bootable flash.bin again") adjusted to apply to i.MX8MQ.
Signed-off-by: Patrick Wildt <patrick@blueri.se>
Reviewed-by: Fabio Estevam <festevam@denx.de>
CMD_DM is useful for showing the whole DM tree.
Enable it via "imply CMD_DM".
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
The binman node is part of the imx8mm-u-boot.dtsi file which
is duplicated in imx8mm-kontron-n801x-s-u-boot.dtsi and causes
a build error. Remove the duplicate.
Fixes: 3cbb31f0e848 ("arm64: dts: imx8mm: use common binman configuration")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The binman node is part of the imx8mm-u-boot.dtsi file which
is duplicated in phycore-imx8mm-u-boot.dtsi and causes a build
error. Remove the duplicate.
Fixes: 3cbb31f0e848 ("arm64: dts: imx8mm: use common binman configuration")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
