The Vybrid reference manual VFXXXRM Rev. 0 10/2016 states in chapter
5.2.6.1 DUMMY PADS (DDR/QuadSPI) that those pads need to be programed
for correct operation of DDR. Assume the default DDR pin configuration
which seems to work well on a Colibri VF50.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
When running usb dwc3 gadget driver, we meet random USB enumeration failure in fastboot.
The root cause is a cache coherence issue. When it happens, the ctrl_req in
gadget driver is allocated at 0xfe932f40, and the usb_composite_dev (cdev)
is allocated at 0xfe932f60. So after we submit the setup request (cache flushed) to USB
controller, any accessing to usb_composite_dev variable will cause the cache line refill, then
when setup transfer is completed, reading the setup data in ctrl_req will gets old value from
cache not from memory.
The ctrl_req is allocated by API dma_alloc_coherent, but u-boot don't have cohernet memory.
so it still needs cache maintain operations before/after HW accessing. Since the cache flush or
invalidate bases on cache line, so when the allocated memory size is not cache line aligned,
potentially it may meet such issue.
This patch modifies the dma_alloc_coherent API to round the size to cache line aligned.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
There is no code for using partition labels in the Allwinner SPL port.
Even so the name is slightly misleading, CONFIG_SPL_LIBDISK_SUPPORT was
meant to guard partition code for the SPL.
Remove the "imply" line in the Kconfig to make this obvious and avoid
unneeded code inclusions, helping to keep the H6 SPL code small.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Building peach-pi smdk5420 and peach-pit with thumb mode for SPL
ends-up in the following error:
Error: Thumb encoding does not support an immediate here -- `msr cpsr_c,#0x13|0xC0'
Use an intermediate register to be able to use thumb for exynos5 SPL.
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch sets VDD_LOG to 950 mV on RK3399-Q7.
This is required to address stability issues on Puma
in heavy-load use-cases.
Reported-by: Assaf Agmon <assaf@r-go.io>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This patch eliminates the non-standard entries "rockchip,pwm_id"
and "rockchip,pwm_voltage". They are neither documented nor
read out by any driver.
Additionally it introduces the entry regulator-init-microvolt
and sets it to 900 mV, which is the default target value
for VDD_LOG.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
All the source code of sdram_rk3036.c are from Rockchip, update the
copyright to owned by Rockchip.
Because rockchip may use this copy of code both for open source
project and internal project, update the license to use both
GPL2.0+ and BSD-3 Clause.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This is workaround for issue we can't get correct size for 4GB ram
in 32bit system and available before we really need ram space
out of 4GB, eg.enable ARM LAPE(rk3288 supports 8GB ram).
The size of 4GB is '0x1 00000000', and this value will be truncated
to 0 in 32bit system, and system can not get correct ram size.
Rockchip SoCs reserve a blob of space for peripheral near 4GB,
and we are now setting SDRAM_MAX_SIZE as max available space for
ram in 4GB, so we can use this directly to workaround the issue.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Tested-By: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Build flash.bin for i.MX8MQ, it will include signed hdmi firmware,
spl, ddr firmware, fit image(bl31.bin, u-boot-nodtb.bin, dtb).
Burn it to 33KB offset of SD card.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Refactor dram_pll_init to accept args to configure different pll freq.
Introduce dram_enable_bypass and dram_disable_bypass
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Build u-boot-dtb.cfgout before checking files, otherwise
u-boot-dtb.cfgout is generated at late stage and cause final image not
generated.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Current implementation of hab_auth_img command needs ivt_offset to
authenticate the image. But ivt header is placed at the end of image
date after padding.
This leaves the usage of hab_auth_img command to fixed size or static
offset for ivt header. New function "get_image_ivt_offset" is introduced
to find the ivt offset during runtime. The case conditional check in this
function is same as boot_get_kernel in common/bootm.c
With this variable length image e.g. FIT image with any random size can
have IVT at the end and ivt_offset option can be left optional
Can be used as "hab_auth_img $loadaddr $filesize" from u-boot script
Signed-off-by: Parthiban Nallathambi <pn@denx.de>
Reviewed-by: Breno Lima <breno.lima@nxp.com>
This file is in sync with v4.20-next tree:
e4dda4f5a4df "x86/kaslr, ACPI/NUMA: avoid including asm/kaslr.h on arm64"
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This node is in sync with v4.20-next tree:
e4dda4f5a4df "x86/kaslr, ACPI/NUMA: avoid including asm/kaslr.h on arm64"
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Introduce two board level callback functions to FIT image loading process, and
a SPL_FIT_FOUND flag to differentiate FIT image or RAW image.
Implement functions in imx common SPL codes to call HAB funtion
to authenticate the FIT image. Generally, we have to sign multiple regions
in FIT image:
1. Sign FIT FDT data (configuration)
2. Sign FIT external data (Sub-images)
Because the CSF supports to sign multiple memory blocks, so that we can use one
signature to cover all regions in FIT image and only authenticate once.
The authentication should be done after the entire FIT image is loaded into
memory including all sub-images.
We use "-p" option to generate FIT image to reserve a space for FIT IVT
and FIT CSF, also this help to fix the offset of the external data (u-boot-nodtb.bin,
ATF, u-boot DTB).
The signed FIT image layout is as below:
--------------------------------------------------
| | | | | | | |
| FIT | FIT | FIT | | U-BOOT | ATF | U-BOOT |
| FDT | IVT | CSF | | nodtb.bin | | DTB |
| | | | | | | |
--------------------------------------------------
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Using ulong is wrong as its size depends on the Host CPU architecture
(32-bit vs. 64-bit) although the Cortex-M4 is always 32-bit.
Without this patch, the stack and PC are obviously wrong and it
generates an abort when used on 64-bit processors such as the i.MX8MQ.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Otherwise can't boot the M4 core as it is impossible to load its
firmware into the TCM memory.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Add Kconfig option WATCHDOG_RESET_DISABLE to disable watchdog reset
in imx_watchdog driver, so that the watchdog will not be fed in
u-boot if CONFIG_WATCHDOG_RESET_DISABLE is enabled.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Support watchdog driver for fsl-lsch2. It's disabled in default.
If you want to use it, please enable CONFIG_IMX_WATCHDOG.
Define CONFIG_WATCHDOG_TIMEOUT_MSECS to set watchdog timeout.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Currently, the DWC3 USB node is out of sync because the bindings
for the UniPhier DWC3 PHY diverged between Linux and U-Boot.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Some users might want to modify 'bootcmd' at compile-time by editing
include/configs/uniphier.h, but overwriting it at run-time makes it
impossible.
Instead, set 'bootdev' at run-time, which contains the boot device the
system is booting from, then indirectly reference it from 'bootcmd'.
It is up to users whether to override 'bootcmd'.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This patch changes mt7629 to use the compatible platform SMP initialization
method of linux kernel.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
For signing the tiboot3.bin image, an optional KEY file can be passed
using CONFIG_SYS_K3_KEY. Right now, Makefile scripts directly takes
the config value and uses it for signing. This is okay if the build
directory is a sub-directory of source tree, otherwise it fails.
Fix it by using the path relative to the source tree.
Reported-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
OMAP3_GPIO_x is needed to enable each GPIO bank on the OMAP3
boards. At one point, the #ifdef's were replaced with
if CONFIG_IS_ENABLED but this won't work for people who need
OMAP3_GPIO_x in SPL since the SPL prefix for this option isn't
used in Kconfig. This patch moves the check to #if defined and
also makes Kconfig select the banks if CMD_GPIO is used which
makes the checks in the code less cumbersome.
Fixes: bd8a9c14c9 ("arm: mach-omap2/omap3/clock.c: Enable
all GPIO with CMD_GPIO")
Reported-by: Liam O'Shaughnessy <liam.o.shaughnessy@gumstix.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Migrate omap3_igep00x0.h]
Signed-off-by: Tom Rini <trini@konsulko.com>
This patch allows smaller binaries.
This is needed for and has been tested on Arndale board, as u-boot.bin is
now bigger than the 512K load limit, with GCC8, without thumb mode.
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Tom Rini <trini@konsulko.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The Marvell DDR3 training code is now part of the U-Boot SPL so the
comment saying it needs porting is no longer correct.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Enable 'fpga' command in u-boot. User will be able to use the FPGA
command to program the FPGA on Stratix10 SoC.
Signed-off-by: Ang, Chee Hong <chee.hong.ang@intel.com>
Add a generic mailbox API for FPGA reconfig status which can be
called by others. This new function accepts 2 different mailbox
commands: CONFIG_STATUS or RECONFIG_STATUS.
Signed-off-by: Ang, Chee Hong <chee.hong.ang@intel.com>
Under U-boot, the WiFi SDIO Module should be disabled and the
eMMC modules should be enabled, so this patch adds an s400-u-boot.dtsi
include file specific for U-Boot that will be included by the build system.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Add support for the Creator CI20 platform based on the JZ4780 SoC.
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Add initial support for the Ingenic JZ47xx MIPS SoC.
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Add header with SPL boot mode and type definitions.
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Adding the support for the Luton boards PCB91 which share common code with
the Ocelots boards, including board code, device tree and configuration.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This family of SoCs are found in the Microsemi Switches solution and have
already a support in the linux kernel.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This path add a new helper allowing to prefetch and lock instructions
into cache. This is useful very early in the boot when no RAM is
available yet.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Export create_tlb() as an inline function in mipsregs.h. It allows to
remove the declaration of the function from the board files.
Then it will allow also to use this function very early in the boot when
the stack is not usable.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
With moving write_on_tlb() to arch/mips/include/asm/mipsregs.h
there are now compiler warnings when some generic code includes
asm/io.h. This happens for example when enabling OF live tree.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
It has been noticed, that sometimes the d-cache is not in a
"clean-state" when U-Boot is running on MT7688. This was detected when
using the ethernet driver (which uses d-cache) and a TFTP command does
not complete. Flushing the complete d-cache (again?) here seems to fix
this issue.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This fixes following DTC warning:
arch/mips/dts/nexys4ddr.dtb: Warning (compatible_is_string_list): /ethernet@10e00000/mdio/phy@1:compatible: property is not a string list
As upstream DTS in Linux doesn't have the offending property,
simply remove it to fix the warning.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Remove all interrupt nodes that cause warnings regarding a missing
interrupt parent. There are no interrupt controller nodes defined
and the device trees don't match the ones in Linux anymore.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This is not used by any board. Remove it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Anup Patel <anup@brainfault.org>
Avoid reading mhartid CSR directly, instead use the one we saved
in the global data structure before.
With this patch, BBL no longer needs to be hacked to provide the
mhartid CSR emulation for S-mode U-Boot.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Anup Patel <anup@brainfault.org>
At present the hart id passed via a0 in the U-Boot entry is saved
to s0 at the beginning but does not preserve later. Save it to the
global data structure so that it can be used later.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Anup Patel <anup@brainfault.org>
With this change, we can avoid a forward declaration.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Anup Patel <anup@brainfault.org>
At present the trap handler returns to hardcoded M-mode/S-mode.
Change to returning to previous privilege level instead.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Anup Patel <anup@brainfault.org>
sp cannot be loaded before restoring other registers.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Anup Patel <anup@brainfault.org>
Currently the M-mode trap handler codes are in start.S. For future
extension, move them to a separate file mtrap.S.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Anup Patel <anup@brainfault.org>
In arch_cpu_init_dm() do some basic architecture level cpu
initialization, like FPU enable, etc.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Anup Patel <anup@brainfault.org>
With current csr_xxx ops, we cannot pass a macro to parameter
'csr', hence we need add another level to allow the parameter
to be a macro itself, aka indirect stringification.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Anup Patel <anup@brainfault.org>
This updates supports_extension() implementation to use the desc
string from the cpu driver whenever possible, which avoids the
reading of misa CSR for S-mode U-Boot.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Anup Patel <anup@brainfault.org>
This adds all exception codes in encoding.h.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Anup Patel <anup@brainfault.org>
The standard RISC-V ISA sets aside a 12-bit encoding space for up
to 4096 CSRs. This adds all known CSR numbers as defined in the
RISC-V Privileged Architecture Version 1.10.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Anup Patel <anup@brainfault.org>
With DM CPU driver, the non-DM version of print_cpuinfo() is no
longer needed.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Anup Patel <anup@brainfault.org>
This calls cpu_probe_all() to probe all available cpus.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Anup Patel <anup@brainfault.org>
Increase the heap size for the pre-relocation stage, so that CPU
driver can be loaded.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Anup Patel <anup@brainfault.org>
Add the QEMU RISC-V platform-specific Kconfig options, to include
CPU and timer drivers.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Anup Patel <anup@brainfault.org>
This adds an implementation of riscv_get_time() API that is using
rdtime instruction.
This is the case for S-mode U-Boot, and is useful for processors
that support rdtime in M-mode too.
Signed-off-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
This adds U-Boot syscon driver for SiFive's Core Local Interruptor
(CLINT). The CLINT block holds memory-mapped control and status
registers associated with software and timer interrupts.
This driver implements the riscv_get_time() API as required by
the generic RISC-V timer driver, as well as some other APIs that
are needed for handling IPI.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Anup Patel <anup@brainfault.org>
So far we have a Kconfig option for supervisor mode. This adds an
option for the machine mode.
Signed-off-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
There is no need to expose RISCV_NDS to the Kconfig menu as it is
an ax25-specific option. Introduce a dedicated Kconfig option for
the cache ops of ax25 platform and use that to guard the cache ops.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Rick Chen <rick@andestech.com>
To enumerate devices on the /soc/ node, create a "simple-bus"
driver to match "riscv-virtio-soc".
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Anup Patel <anup@brainfault.org>
RISC-V has two code models, medium low (medlow) and medium any (medany).
Medlow limits addressable memory to a single 2 GiB range between the
absolute addresses -2 GiB and +2 GiB. Medany limits addressable memory
to any single 2 GiB address range.
By default, medlow is selected for U-Boot on both 32-bit and 64-bit
systems.
The -mcmodel compiler flag is selected according to the Kconfig
configuration.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
[bmeng: adjust to make medlow the default code model for U-Boot]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Add the initial support for Elgin R1 board, which is based on the
RV1108 SoC and has the following features currently supported in
U-Boot:
- UART
- eMMC
- USB
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This is a sync with kernel mainline dts.
The U-Boot eMMC does not need to care about the power for Rockchip
SoCs, because if the board is using eMMC, the power will default on
(for bootrom), so the 'vmmc', 'vqmmc' is only useful for SD in U-Boot.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
vcc5v0_host and usbhub_enable share gpio4 RK_PA3,
which is a problem during probing (the second probe
will trigger a -EBUSY, when trying to get the gpio handle).
An analysis of the situation shows, that both regulators
are actually describing the same supply.
This patch removes the (currenlty not successful probing)
regulator vcc5v0_host from the DTS and adds the pinctrl-*
setting to usbhub_enable.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Phiilipp Tomsich <philipp.tomsich@theobroma-systems.com>
Commit 4687919684 ("serial: Remove DM_FLAG_PRE_RELOC flag in various
drivers") essentially drops flag DM_FLAG_PRE_RELOC from serial_pl01x
driver for Poplar platform, because the platform falls into the
following strategy category made by the commit.
Surround DM_FLAG_PRE_RELOC flag with OF_CONTROL check, for
drivers that support both statically declared devices and
configuration from device tree
Before the commit lands, Poplar platform works by statically declaring
pl011 serial device via U_BOOT_DEVICE() with DM_FLAG_PRE_RELOC flag set
in the driver. But since Poplar also supports device configuration from
device tree, the commit practically drops the flag for Poplar, and hence
breaks the platform from booting.
This patch changes platform code and device tree to initiate pl011
serial device from device tree rather than static declaration, so that
above strategy about DM_FLAG_PRE_RELOC applies to Poplar, and therefore
the reported boot failure gets fixed.
Reported-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Fixes: 4687919684 ("serial: Remove DM_FLAG_PRE_RELOC flag in various drivers")
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Tested-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When DM_USB is used, either the USB controllers are bound when the DTB
is parsed (when OF_CONTROL is enabled) or they are bound using the
U_BOOT_DEVICES() macro.
In the later case, the platform data is passed in a struct ti_musb_platdata
because it cannot be read from the DTB.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable DM for USB peripheral in the musb-new driver.
Also make sure that the driver can be used in the SPL.
This implies that:
* the driver must work with and without the OF_CONTROL option. That
in turn, implies that the platform data can be passed in a struct
ti_musb_platdata or be read from the dtb
* usb.o is linked in the SPL if host support is enabled
Another change is that the driver does not fail to bind (and stop the boot
process) if one of the child driver does not bind. Reporting the error is
enough. This kind of error would appear if the port is configured in the
DTS but the driver is not activated in the config.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
USB1 can be used by the romboot on all am4372 platforms to download a
firmware (SPL in our case).
It makes sense to enable USB1 in the SPL to download u-boot.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This file is used to override the values found in am4372.dtsi
Use it to fix the "compatible" options for the controllers used
to support the USB (parent bus and syscons).
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
At present these parameters are hard-coded in the sdl interface code.
Allow them to be specified by the driver instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Update sandbox's device tree and config to use driver model for sound. Use
the double buffer for sound output so that we don't need to wait for the
sound to complete before returning.
Signed-off-by: Simon Glass <sjg@chromium.org>
Update snow's device tree and config to use driver model for sound. Also
update the others as best we can.
Spring does not appear to have audio support in the kernel. The smdk5250
and smdk5420 boards use a wolfson codec which I cannot test with. So the
only boards that is tested and known to work are snow, pit and pi.
Signed-off-by: Simon Glass <sjg@chromium.org>
Allow setting the i2s pinmux correctly on exyno5420 so that i2c can be
used on that SoC. Also rename EXYNOS_AUDSS to something consistent with
other naming.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current dev_read...() functions use s32 and u32 which are convenient
for device tree but not so useful for normal code, which often wants to
use normal integers for values.
Add a helper which supports returning an unsigned int. Also add signed
versions of the unsigned readers.
Signed-off-by: Simon Glass <sjg@chromium.org>
The sound driver pulls together the audio codec and i2s drivers in order
to actually make sounds. It supports setup() and play() methods. The
sound_find_codec_i2s() function allows locating the linked codec and i2s
devices. They can be referred to from uclass-private data.
Add a uclass and a test for sound.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we use a single buffer for sound which means we cannot be
playing one sound while queueing up the next. This wouldn't matter except
that a long sound (more than a second) has to be created as a single
buffer, thus using a lot of memory. To better mimic what real sound
drivers do, add support for double buffering in sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
The i2s bus is commonly used with audio codecs. It provides a way to
stream digital data sychronously in both directions. U-Boot only supports
audio output, so this uclass is very simple, with a single tx_data()
method.
Add a uclass and a test for i2s.
Signed-off-by: Simon Glass <sjg@chromium.org>
An audio codec provides a way to convert digital data to sound and vice
versa. Add a simple uclass which just supports setting the parameters for
the codec.
Signed-off-by: Simon Glass <sjg@chromium.org>
The U-Boot sound system provides basic support for beeping. At present it
does not use driver model, but it needs to be converted. Add an option to
enable driver model for sound. For now it is not connected to anything.
Future work will add drivers which use this option. It will then be
removed once everything is converted.
Signed-off-by: Simon Glass <sjg@chromium.org>
For snow the codec is at address 0x11 on the i2c bus, in 7-bit format.
The device tree and code are in 8-bit format (i.e. shifted left one bit).
Fix both. Fix pit in a similar way.
Signed-off-by: Simon Glass <sjg@chromium.org>
There is no need for an embedded device tree for this board so let the
build process generate a separate u-boot.dtb file instead.
Signed-off-by: Felix Brack <fb@ltec.ch>
Add support for lx2160a SoC
-----BEGIN PGP SIGNATURE-----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=aT7d
-----END PGP SIGNATURE-----
Merge tag 'fsl-qoriq-for-v2019.01-rc2' of git://git.denx.de/u-boot-fsl-qoriq
Add TFA boot flow for some Layerscape platforms
Add support for lx2160a SoC
[trini: Add a bunch of missing MAINTAINERS entries]
Signed-off-by: Tom Rini <trini@konsulko.com>
- init DRAM for RK322x in SPL
- add FAN53555 PMIC/regulator driver
- update MicroCrystal RV3029 driver to Kconfig and sync from Linux
- add bootcount uclass and first DM-driver for bootcount
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcDiw9AAoJECaAFcEOcohNEa8H/RBWLbVQjHPXf6EjchXgVcSs
Gc+g2QmKZbN21XebfzBpCuZj62NROTWUcrPtor17yEBiMM1xPfe1vC7qtbkR6USj
VTt1JHeyGx3XafkkUpeps382YPfuaNqtabjwZaXlmeE4/VLbXQPE7x4tC4fdWus4
9K3OGQgRNFirn+RIZ7dQWtCby82PEC3cHkPc/n82cVHofcDsgKYK9mPpfcCn/gWF
A4Fa9cx4pjeaMrBHKjcByCiFmwYBPc97Hqzz64oHOdQP0g3h04ko+2w5DdwdeHVV
jKNcvkHESF4m1RGjrTbLEhy1f5UuOfcA1ise/cDX4pjXlBdwxHmvqT5vsE0MQzI=
=5sHL
-----END PGP SIGNATURE-----
Merge tag 'for-master-20181210' of git://git.denx.de/u-boot-rockchip
Improvements:
- init DRAM for RK322x in SPL
- add FAN53555 PMIC/regulator driver
- update MicroCrystal RV3029 driver to Kconfig and sync from Linux
- add bootcount uclass and first DM-driver for bootcount
Now that we have FAN53555 support, we can enable the regulators in our
DTS. To make these easier to identify on the U-Boot commandline, we
rename them to the names of the voltage rails they control.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The DRA7 platforms requires that the dtb used in the SPL really matches the
platform to have the best MMC performances.
To detect the board type/version an I2C EEPROM is read. This requires that
DM is initialized before the detection. As a consequence we must reset the
DM after the board detection is a new dtb would better match the platform.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
DM_I2C_COMPAT is a compatibility layer that allows using the non-DM I2C
API when DM_I2C is used. The goal is to eventually remove DM_I2C_COMPAT
when all I2C "clients" have been migrated to use the DM API.
This a step in that direction for the TI based platforms.
Build tested with buildman:
buildman -dle am33xx ti omap3 omap4 omap5 davinci keystone
boot tested with:
am335x_evm, am335x_boneblack, am335x_boneblack_vboot (DM version),
am57xx_evm, dra7xx_evm, k2g_evm, am437x_evm
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
In order to use DM_I2C, we need to move the board detection after the
early SPL initialization.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
If DM_I2C is used , the I2C controllers must be registered as U_BOOT_DEVICE
because OF_CONTROL is not used in the SPL.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
This allows the driver to be used without OF_CONTROL.
AM335x support DM_SPL but does not use SPL_OF_CONTROL. Enabling DM_I2C in
SPL thus requires that the omap I2C can be passed platdata.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Move away from SoC specific headers to handle different register layout.
Instead use driver data to get appropriate register layouts like in the
kernel. While at it, perform some mostly cosmetic alignment/cleanup in
the functions being updated.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Up until now the call to initialize the USB subsystem was hardcoded
for U-Boot running as an EFI payload. This was used to enable the
use of a USB keyboard in the U-Boot shell. However not all boards
might need this functionality. As initializing the USB subsystem can
take a considerable amount of time (several seconds on some boards),
we now initialize the USB subsystem only if U-Boot is configured to
use USB keyboards.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Up until now the call to initialize the USB subsystem was hardcoded
for U-Boot running as a coreboot payload. This was used to enable
the use of a USB keyboard in the U-Boot shell. However not all boards
might need this functionality. As initializing the USB subsystem can
take a considerable amount of time (several seconds on some boards),
we now initialize the USB subsystem only if U-Boot is configured to
use USB keyboards.
Signed-off-by: Thomas RIENOESSL <thomas.rienoessl@bachmann.info>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
At present the Kconfig options (CONFIG_I8259_PIC and CONFIG_APIC)
do not include a prompt message, which makes it impossible to
be disabled from a board defconfig file.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
mask_irq(), unmask_irq() and specific_eoi() are provided by the
i8259 PIC driver and should be wrapped with CONFIG_I8259_PIC.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Hannes Schmelzer <oe5hpm@oevsv.at>
There are still systems running which do not have any LAPIC or even
IOAPIC. Responsible MSRs for those do not exist and the systems are
crashing on trying to setup LAPIC.
This commit makes the APIC stuff able to switch off for those boards
which dont' have an LAPIC / IOAPIC.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Make the indentation aligned with what used elsewhere in U-Boot.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Intel Tangier SoC has RTC inside. So, enable it in ACPI.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Similar to Clearfog rev 2.1, GPIO 19 also used to reset onboard ethernet
PHY.
This patch depend on
net: mvneta: Add GPIO configuration support
[URL: https://patchwork.ozlabs.org/patch/1007736/]
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-By: Dennis Gilmore <dgilmore@redhat.com>
Reviewed-By: Dennis Gilmore <dgilmore@redhat.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Enable SPI flash support under U-Boot and SPL. The ENV size and offset,
ported from U-Boot 2013.01 Marvell version: 2015_T1.0p16
To create U-Boot image for SPI flash, user would need to replace
* CONFIG_MVEBU_SPL_BOOT_DEVICE_MMC with CONFIG_MVEBU_SPL_BOOT_DEVICE_SPI
* CONFIG_ENV_IS_IN_MMC with CONFIG_ENV_IS_IN_SPI_FLASH
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-By: Dennis Gilmore <dgilmore@redhat.com>
Reviewed-By: Dennis Gilmore <dgilmore@redhat.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Enable Marvell I2C driver and I2C IO expander. Set default bus to
external I2C bus. Define I2C aliases in device tree so it can be
recognized by the driver.
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-By: Dennis Gilmore <dgilmore@redhat.com>
Reviewed-By: Dennis Gilmore <dgilmore@redhat.com>
Signed-off-by: Stefan Roese <sr@denx.de>
When we clear a pmic_bus bit, we do a read-modify-write operation.
We waste some time however, by writing back the exact samea value
that was already set in the chip. Let us thus only do the write
in case data was changed.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
For a small SPL, it should be possible to build without SPI(-flash) drivers
or wihout MMC drivers.
For this to work, we have to change from 'select'ing options to 'imply'ing
them.
With this change, I can have SPL trimmed to my hard-wired starting method
(SPI-NOR or MMC) while still including all drivers in U-Boot.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
This is required when DM_USB is used, to bind the USB phys.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
syscon_regmap_lookup_by_phandle() can be used to get the regmap of a syscon
device from a reference in the DTS. It operates similarly to the linux
version of the namesake function.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Using CONFIG_DM_USB for this purpose prevents using DM_USB for host and not
for device.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
This patch fixes the problem that u-boot will not start unless icache is
enabled early.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
This patch fixes the problem that "main memory domain AXI secure access
protection error" occurs. Exclude the area (0x43f00000 to 0x47DFFFFF)
set by DBSC from the map area.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
This patch fixes the problem that "main memory domain AXI secure
access protection error" occurs when booting Cortex-A53. Exclude
the area (0x43f00000 to 0x47DFFFFF) set by DBSC from the map area.
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
This patch synchronizes the am33xx SoC specific files with those from
Linux 4.20.0. Hence all board maintainers of am33xx based boards are
on the cc list.
The main purpose of this patch is to prevent further diverging of the
dts files from U-Boot and those from Linux. It aims to set the stage
for the synchronization of board specific dts files. Example: I'm the
maintainer of the PDU001 board: once this patch is applied successfully
I will make changes to the board specific dts file in Linux only and
then post a patch with a copy of this exact dts file to U-Boot. This
will make U-Boot and Linux remain in sync.
The stumbling block of https://patchwork.ozlabs.org/patch/943627 was
removed by the patch https://patchwork.ozlabs.org/patch/962428 from
Lokesh Vutla (many thanks!). This omap-serial driver allows using the
Linux am33xx.dtsi file in U-Boot.
Other changes to dts and dtsi files made by this patch are mainly to
prevent _new_ warnings during the build process. Especially the warning
at pinmux@800 stating 'unnecessary #address-cells/#size-cells without
"ranges" or child "reg"' was not removed. This warning is a good example
showing the benefit of the synchronization: if it needs to be fixed it
will be fixed in Linux and ported back to U-Boot.
Buildman reports all 46 am33xx SoC based boards to build fine, with
warnings of course. Nevertheless this patch should be tested thoroughly
on as many boards as possible to prevent any collateral damage.
Signed-off-by: Felix Brack <fb@ltec.ch>
Reviewed-by: Tom Rini <trini@konsulko.com>
In some STM32 SoC packages, GPIO bank has not always 16 gpios.
Several cases can occur, gpio hole can be located at the beginning,
middle or end of the gpio bank or a combination of these 3
configurations.
For that, gpio bindings offer the gpio-ranges DT property which
described the gpio bank mapping.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
This patch enables CONFIG_BLK as well as CONFIG_DM_MMC for the PDU001
board. It depends on Patrice Chotard's patch 'power: regulator: denied
disable on always-on regulator' which prevents power cycling the vmmc
supply. Without this patch the board will not boot as vmmc is
unfortunately used by other board components, not just eMMC and micro SD
card. Furthermore my patch 'dts: am335x-pdu001: Fix polarity of card
detection input' is required to boot from external micro SD card. Without
this patch no SD card will be detected and hence booting will fail.
Signed-off-by: Felix Brack <fb@ltec.ch>
Reviewed-by: Tom Rini <trini@konsulko.com>
When a micro SD card is inserted in the PDU001 card cage, the card
detection switch is opened and the corresponding GPIO input is driven
by a pull-up. Hence change the active level of the card detection
input from low to high.
Signed-off-by: Felix Brack <fb@ltec.ch>
Add test for the SPL binary size and the bss section size.
This will throw an error at build time if the SPL sections
do not fit in the designated RAM area, thus avoiding oversizing the SPL.
Based on original work by Wenyou Yang.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Protect configuration registers with a hardware spinlock.
If a hwspinlock is defined in the device-tree node used it
to be sure that none of the others processors on the SoC could
change the configuration at the same time.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Implement hardware spinlock support for STM32MP1.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
This is uclass for Hardware Spinlocks.
It implements two mandatory operations: lock and unlock
and one optional relax operation.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
NXP layerscape architecture Chassis 3.2 builds upon chassis3
architecture with changes like DDR Memory map change,
removal of IFC and support of upto 8 I2C controller.
Patch add README.lsch3_2 and the above changes under
macro CONFIG_NXP_LSCH3_2.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Some lsch3 based SoCs like lx2160a contains three
serdes modules.
Add support for third serdes protocol in lsch3
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
One ls2080a, there is one SATA 3.0 advanced host controller interface
which is a high-performance SATA solution that delivers comprehensive
and fully-compliant generation 3 (1.5 Gb/s - 6.0 Gb/s) serial ATA
capabilities, in accordance with the serial ATA revision 3.0 of Serial
ATA International Organization.
Add sata node to support this feature.
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
One ls1088a, there is one SATA 3.0 advanced host controller interface
which is a high-performance SATA solution that delivers comprehensive
and fully-compliant generation 3 (1.5 Gb/s - 6.0 Gb/s) serial ATA
capabilities, in accordance with the serial ATA revision 3.0 of Serial
ATA International Organization.
Add sata node to support this feature.
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
One ls1046a, there is one SATA 3.0 advanced host controller interface
which is a high-performance SATA solution that delivers comprehensive
and fully-compliant generation 3 (1.5 Gb/s - 6.0 Gb/s) serial ATA
capabilities, in accordance with the serial ATA revision 3.0 of Serial
ATA International Organization.
Add sata node to support this feature.
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add support of MC framework for TFA
Make MC framework independent of boot source.
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Returns job ring status as true in TFABOOT, as one job ring is always
reserved.
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Changes the el2_to_aarch32 SMC ID from 0xc000ff04 to 0xc200ff17,
it is applicable to both TFA and non-TFA boot.
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Workaround of erratum A010539 clears the RCW source field in PORSR1
register, causing failure of detecting boot source using this method.
Use SMC call if U-Boot runs at EL2. If SMC is not implemented or
running at EL3, continue to read PORSR1 and presume QSPI as boot
source if erratum workaround A010539 is enabled and RCW source is
cleared.
Signed-off-by: York Sun <york.sun@nxp.com>
OCRAM initialization is performed by TFA, Hence
skipped from u-boot.
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Adds SMC calls for getting DDR size and bank info for TFABOOT.
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Removes EL3 specific erratas for TFABOOT, And now taken care in TFA.
ARM_ERRATA_855873, SYS_FSL_ERRATUM_A008850, SYS_FSL_ERRATUM_A008511,
SYS_FSL_ERRATUM_A008336, SYS_FSL_ERRATUM_A009663,
SYS_FSL_ERRATUM_A009803, SYS_FSL_ERRATUM_A009942,
SYS_FSL_ERRATUM_A010165
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
PORSR register holds the cfg_rcw_src field which can be used
to identify boot source.
Further, it can be used to select the environment location.
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
[YS: fix multiple checkpatch issues]
Reviewed-by: York Sun <york.sun@nxp.com>
Adds TFABOOT support config option and add generic code to enable
execution from DDR.
Signed-off-by: York Sun <york.sun@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Change tlb base address from OCRAM to DDR when exception level is
less than 3.
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
In case SError happens at EL2, if SCR_EL3[EA] is not routing it to
EL3, and SCR_EL3[RW] is set to aarch64, setting HCR_EL2[AMO] routes
the exception to EL2. Otherwise this exception is not taken.
Signed-off-by: York Sun <york.sun@nxp.com>
Add board support for Ficus EE board from Vamrs. This board utilizes
common Rock960 family support.
Following peripherals are tested and known to work:
* Gigabit Ethernet
* USB 2.0
* MMC
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
[Reworked based on common Rock960 family support]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add board support for Rock960 CE board from Vamrs. This board utilizes
common Rock960 family support.
Following peripherals are tested and known to work:
* USB 2.0
* MMC
This commit also adds DDR configuration for LPDDR3-2GiB-1600MHz which
is being used on the board.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Rock960 is a family of boards based on Rockchip RK3399 SoC from Vamrs.
It consists of Rock960 (Consumer Edition) and Ficus (Enterprise Edition)
96Boards.
Below are some of the key differences between both Rock960 and Ficus
boards:
1. Different host enable GPIO for USB
2. Different power and reset GPIO for PCI-E
3. No Ethernet port on Rock960
The common board support will be utilized by both boards. The device
tree has been organized in such a way that only the properties which
differ between both boards are placed in the board specific dts and
the reset of the nodes are placed in common dtsi file.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[Added instructions for SD card boot]
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Those pins would be used by many boards.
Commit grabbed from Linux:
commit b41023282d07b61a53e2c9b9508912b1e7ce7b4f
Author: Randy Li <ayaka@soulik.info>
Date: Thu Jun 21 21:32:10 2018 +0800
arm64: dts: rockchip: add some common pin-settings to rk3399
Those pins would be used by many boards.
Signed-off-by: Randy Li <ayaka@soulik.info>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Signed-off-by: Randy Li <ayaka@soulik.info>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
tpm improvements to clear up v1/v2 support
buildman toolchain fixes
New serial options to set/get config
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAlwIe0gRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreY02wgAjK9U1ADmoNi4xWgtq83EerxOGTq68BRD
CfnUDgI+FQHNv/LxdZ8lZ2lgGG1xXZ8mdeHWghllHoLEnwMQ3LxfDRnpkyC6VBE9
LvZF4F7BhTnGsKImlloQ5oMhKI4sDKjqRkRL3D633x5dq9Z571obAyGwLMo67vv6
U8iv1mRMr6au46pLvH25DF6h5LuM7TBSJVDlzmFmmD++r/YDroTJfo07qdo8sNqS
0hDPjgp3uqf1mX2cbNHk56a3DmO9fL6Gcvdv0LHGQvRyfQ36TY+cEcDU2y2p+tl+
t1LFamfZvalix9AyJegr3qGMOb9B20ar89EItXzH9J+ahnlZmEat+w==
=VAMW
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-5dec18' of git://git.denx.de/u-boot-dm
Minor sandbox enhancements / fixes
tpm improvements to clear up v1/v2 support
buildman toolchain fixes
New serial options to set/get config
Add SPCR table description as it provided in Linux kernel.
Port subtype for ACPI_DBG2_SERIAL_PORT is used as an interface type in SPCR.
Thus, provide a set of definitions to be utilized later.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This functions allow us to get and remap I/O addresses by name, which is useful when there are multiple reg addresses indexed by reg-names property.
This is needed in bmips dma/eth patch series, but can also be used on many
other drivers.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present sandbox has a start.o in the 'start' target but also includes
it in the normal target list. This is not how this is normally handled. It
is needed because sandbox does not include the u-boot-init variable in its
link rule.
Update the rule and move start.o from the normal target list to the
'extras' list.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the RAM buffer is not inited unless it is read from a file,
likely produced by an earlier phase of U-Boot. This causes valgrind
warnings whenever the RAM buffer is used. Correct this by initing it if
needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
ax25-ae350 use CONFIG_OF_BOARD via a2 and CONFIG_SYS_SDRAM_BASE
to boot from ram which allow the board to override the fdt
address originally.
But after this patch
riscv: save hart ID and device tree passed by prior boot stage
It provide prior_stage_fdt_address which offer a temporary
memory address to keep the dtb address passing from loader(gdb)
to u-boot with a1.
So passing via a2 and CONFIG_SYS_SDRAM_BASE is redundant and
can be removed. And it also somehow may corrupted BBL if it
was be arranged in CONFIG_SYS_SDRAM_BASE.
In board_fdt_blob_setup()
When boting from ram:
prior_stage_fdt_address will be use to reserved dtb temporarily.
When booting from ROM:
dtb will be pre-burned in CONFIG_SYS_FDT_BASE, if it is flash base.
Or CONFIG_SYS_FDT_BASE maybe a memory map space (NOT RAM or ROM)
which is provided by HW.
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: Greentime Hu <greentime@andestech.com>
This patch adds kconfig option RISCV_SMODE to run U-Boot in
S-mode. When this opition is enabled we use s<xyz> CSRs instead
of m<xyz> CSRs.
It is important to note that there is no equivalent S-mode CSR
for misa and mhartid CSRs so we expect M-mode runtime firmware
(BBL or equivalent) to emulate misa and mhartid CSR read.
In-future, we will have more patches to avoid accessing misa and
mhartid CSRs from S-mode.
Signed-off-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Move static definitions to cpu.c file, as it doesn't allow
the cpu.h file to be included in multiple c files.
Signed-off-by: York Sun <york.sun@nxp.com>
Set environment variable 'platform' containing the CPU type.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Synchronize DTs with mainline Linux 4.19.6 ,
commit 96db90800c06d3fe3fa08eb6222fe201286bb778
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
V2: Rebase on u-boot/master
Synchronize DTs with mainline Linux 4.19.6 ,
commit 96db90800c06d3fe3fa08eb6222fe201286bb778
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
V2: Rebase on u-boot/master
The i2c6 node is missing in mainline Linux thus far, pull it
into U-Boot specific DT until it hits mainline Linux, to make
syncing of DTs easier.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
V2: Rebase on u-boot/master
The SCIF2 node is not in Linux 4.17 DTs on E3, pull it into U-Boot
specific DT extras until it hits mainline Linux, to make syncing of
DTs easier.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
V2: Rebase on u-boot/master
The SDHI nodes are not in Linux 4.17 DTs in E3, pull them into U-Boot
specific DT extras until they hit mainline Linux, to make syncing of
DTs easier.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
V2: Rebase on u-boot/master
The SDHI nodes are missing features supported in upstream U-Boot,
like mode support properties. Pull the extras into U-Boot specific
DT until it hits mainline Linux, to make syncing of DTs easier.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
V2: Rebase on u-boot/master
The SDHI nodes are missing features supported in upstream U-Boot,
like mode support properties. Pull the extras into U-Boot specific
DT until it hits mainline Linux, to make syncing of DTs easier.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
V2: Rebase on u-boot/master
The CPLD node is missing in Linux 4.17 DTs on H3/M3W ULCB, pull the
node into U-Boot specific DT until it hits mainline Linux, to make
syncing of DTs easier.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
V2: Rebase on u-boot/master
The AVB node is not complete in Linux 4.17 DTs on V3M Eagle, pull the
AVB node extras into U-Boot specific DT until they hit mainline Linux,
to make syncing of DTs easier.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
V2: Rebase on u-boot/master
The SDHI nodes are not in Linux 4.17 DTs in M3N, pull them into U-Boot
specific DT extras until they hit mainline Linux, to make syncing of
DTs easier.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
V2: Rebase on u-boot/master
The USB nodes are not in Linux 4.17 DTs in M3N, pull them into U-Boot
specific DT extras until they hit mainline Linux, to make syncing of
DTs easier.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
V2: Rebase on u-boot/master
The RPC DT bindings are still work in progress. Extract the RPC DT node
from the DT to allow easier update and so it can be replaced once the DT
bindings are stable.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
V2: Rebase on u-boot/master
Add label to the /soc node, so it can be referenced from the U-Boot DTs.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
V2: Rebase on u-boot/master
This release is fully packed with lots of glorious improvements in UEFI
land again!
- Make PE images more standards compliant
- Improve sandbox support
- Improve correctness
- Fix RISC-V execution on virt model
- Honor board defined top of ram (fixes a few boards)
- Imply DM USB access when distro boot is available
- Code cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=6o9t
-----END PGP SIGNATURE-----
Merge tag 'signed-efi-next' of git://github.com/agraf/u-boot
Patch queue for efi - 2018-12-03
This release is fully packed with lots of glorious improvements in UEFI
land again!
- Make PE images more standards compliant
- Improve sandbox support
- Improve correctness
- Fix RISC-V execution on virt model
- Honor board defined top of ram (fixes a few boards)
- Imply DM USB access when distro boot is available
- Code cleanups
This patch switches MCR3000 board to the new DM watchdog.
The change in u-boot.lds is because MCR3000.o grows a bit
with this patch and doesn't fit anymore below env_offset on
some versions of GCC.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Use DM for both MMC and USB subsystems and use dedicated DTS
for U-Boot configuration.
Disable SPL support for GPIO and remove EVMSK leftover for
DDR power control via GPIO.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
