In some cases, the best config cannot be used because the VCO would be
out-of-spec. In these cases, we may need to try a worse combination of r/od
in order to find the best representable config. This also adds a few test
cases to catch this and other (possible) unlikely errors.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Everything here sits in a while (true) loop. However, this introduces a
couple of layers of indentation. We can simplify the code by introducing a
single goto instead of using continue/break. This will also make adding
loops in the next patch easier.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The PLL functions take ulong arguments for rate, but still check if that
rate is negative (which is never true). The correct way to handle this is
to use IS_ERR_VALUE (like is already done in k210_clk_set_rate). While
we're at it, we can move the error checking up into the caller of the pll
set/get rate functions. This also protects our other calculations from
using bogus values for rate.
Fixes: 609bd60b94 ("clk: k210: Rewrite to remove CCF")
Reported-by: Coverity Scan <scan-admin@coverity.com>
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The values of CONFIG_NAND_OMAP_ECCSCHEME map to the enum in
include/linux/mtd/omap_gpmc.h for valid ECC schemes. Make which one we
will use be a choice statement, enumerating the ones which we have
implemented.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_NAND_FSL_ELBC
CONFIG_NAND_FSL_IFC
Note that a number of PowerPC platforms had previously enabled
CONFIG_NAND_FSL_ELBC without CONFIG_MTD_RAW_NAND, and now they no longer
enable the option, reducing the size of a few functions.
Signed-off-by: Tom Rini <trini@konsulko.com>
We only include <linux/mtd/rawnand.h> in <nand.h> for the forward
declaration of struct nand_chip, so do that directly. Then, include
<linux/mtd/rawnand.h> where required directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_NAND_BAD_BLOCK_POS
In order to do this, introduce a choice for HAS_LARGE/SMALL_BADBLOCK_POS
as those are the only valid values. Use LARGE as the default as no
in-tree boards use SMALL, but it is possible.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_NAND_LOAD
CONFIG_SYS_NAND_BLOCK_SIZE
CONFIG_SYS_NAND_PAGE_SIZE
CONFIG_SYS_NAND_OOBSIZE
Signed-off-by: Tom Rini <trini@konsulko.com>
Use dev_ function to read the sides and colour to support a live tree.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use dev_ function to read the name and boolean to support a live tree.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The generic GPIO flags binding is shared across many drivers, some of
which need their own xlate function. Factor out the flag translation
code from gpio_xlate_offs_flags so it does not need to be duplicated.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Translation of an OF GPIO specifier should fail if the pin offset is
larger than the number of pins in the GPIO bank.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Translation of a pin name to a device+offset should fail if the offset
is larger than the number of pins in the GPIO bank.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Parse different gpio properties from dt as part of probe
function. This detail is required to enable pinctrl pad
later when gpio lines are requested.
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Signed-off-by: Bharat Gooty <bharat.gooty@broadcom.com>
Acked-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Both dummy.nbytes and dummy.buswidth may be zero. By not checking
the later, it is possible to trigger division by zero and a crash.
This does happen with tiny SPI NOR framework in SPL. Fix this by
adding the check and returning zero dummy bytes in such a case.
Fixes: 38b0852b0e ("spi: cadence-qspi: Add support for octal DTR flashes")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Pratyush Yadav <p.yadav@ti.com>
[trini: Drop Pratyush's RB as his requested changes weren't made as
Marek disagreed]
To avoid the need of extra boot scripting on AM65x for loading a
watchdog firmware, add the required rproc init and loading logic for the
first R5F core to the watchdog start handler. In case the R5F cluster is
in lock-step mode, also initialize the second core. The firmware itself
is embedded into U-Boot binary to ease access to it and ensure it is
properly hashed in case of secure boot.
One possible firmware source is https://github.com/siemens/k3-rti-wdt.
The board is responsible for providing the firmware as additional
loadable via the U-Boot fit image. The driver will pick up its location
from /fit-images/k3-rti-wdt-firmware then.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
To avoid W=1 build warnings, declare this function as static, since it
is not used outside of this translation module.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The function prototype for ft_pci_setup is inside fdt_support.h, we need
to include that header.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
To avoid W=1 build warnings, declare this function as static, since it
is not used outside of this translation module.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
To avoid W=1 build warnings, declare this function as static, since it
is not used outside of this translation module.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
To avoid W=1 build warnings, declare this function as static, since it
is not used outside of this translation module.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
To avoid W=1 build warnings, declare this function as static, since it
is not used outside of this translation module.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
To avoid a build warning with W=1, provide a function prototype for
dm_pciauto_prescan_setup_bridge, which is a non-static function whose
definition is inside pci_auto.c.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Writing of individual registers was not functioning
correctly as a 0 'offset' byte under DM-managed
I2C was being appended in front of register we
wanted to access.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
The RX8025/RX8035 does not like having it's time registers
set byte-by-byte in separate I2C transactions.
From the note at the top of the file, it appears
target-dependent workarounds have been used in the
past for this.
Resolve this by setting the time registers in a single
I2C transaction.
As part of this, also ensure the '24/12' flag in the RTC
is reset before writing the date (instead of after), otherwise
the RX8035 will clear the seconds and minutes registers.
Tested on Traverse Ten64 (NXP LS1088A) with RX8035.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
The RX8035 is a newer model from EPSON which is
very similar in operation to the RX8025.
The changes mirror similar ones that will be
in Linux 5.15:
https://lore.kernel.org/all/20210709044518.28769-2-matt@traverse.com.au/
The UBOOT_DRIVER ID has also been corrected, previously
it declared itself as rx8010sj_rtc which is a different driver.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
A search of the tree showed there is only one user
of this driver (soon to be two) - board/socrates
The second user will be the Traverse Ten64 board.
Both these boards have DM_RTC.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
We enforce that DM_SERIAL will have SYS_MALLOC_F enabled and so
SYS_MALLOC_F_LEN will have a value. Remove the build-time check.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline.
Remove it. As this is the last ARCH_MX25 platform, remove those
references as well.
Cc: Matthias Weisser <weisserm@arcor.de>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline.
Remove it. As this is the last armada100 platform, remove that support
as well.
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline.
Remove it. As this is the last mx35 platform, remove that support as
well.
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefano Babic <sbabic@denx.de>
zynq:
- Enable capsule update for qspi and mmc
- Update zed DT qspi compatible string
zynqmp:
- Add missing modeboot for EMMC
- Add missing nand DT properties
- List all eeproms for SC on vck190
- Add vck190 SC psu_init
clk:
- Handle only GATE type clock for Versal
watchdog:
- Update versal driver to handle system reset
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYVWWZgAKCRDKSWXLKUoM
IY3MAJ43Mlut5tK9gv45bp4HpyVOMuSvJwCfTiVr7ZxrBE8I8QC5+zHzBTmuM6g=
=aQtT
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.01-rc1' of https://source.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2022.01-rc1
zynq:
- Enable capsule update for qspi and mmc
- Update zed DT qspi compatible string
zynqmp:
- Add missing modeboot for EMMC
- Add missing nand DT properties
- List all eeproms for SC on vck190
- Add vck190 SC psu_init
clk:
- Handle only GATE type clock for Versal
watchdog:
- Update versal driver to handle system reset
Wdt expire command makes the wdt to count least possible ticks(1)
and expires immediately. Add expire_now option to the xlnx_wwdt_ops
and implement it by calling xlnx_wwdt_start() with minimum possible
count(1).
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/1632808919-8600-3-git-send-email-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Existing driver uses generic watchdog mode which generates a signal to
PLM firmware, but the signal cannot be used to reset the system.
Change driver to use window watchdog basic mode. This window watchdog mode
generates a signal to PLM firmware which decides what action to take upon
expiry of watchdog.
Timeout value for xlnx_wwdt_start will come in milli seconds from wdt
framework. Make changes to load count value accordingly.
Add checks before loading the timer for min and max possible values.
Fix authour email id of Ashok Reddy Soma to long email id.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/1632808919-8600-2-git-send-email-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Clocks should be enabled or disabled only if they are of GATE type
clocks. If they are not of GATE type clocks, don't touch them.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/1632808827-6109-1-git-send-email-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
nand_dt_init() is still using fdtdec_xx() interface.
If OF_LIVE flag is enabled, dt property can't be get anymore.
Updating all fdtdec_xx() interface to ofnode_xx() to solve this issue.
For doing this, node parameter type must be ofnode.
First idea was to convert "node" parameter to ofnode type inside
nand_dt_init() using offset_to_ofnode(node). But offset_to_ofnode()
is not bijective, in case OF_LIVE flag is enabled, it performs an assert().
So, this leads to update nand_chip struct flash_node field from int to
ofnode and to update all nand_dt_init() callers.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Before e2e95e5e25 ("spi: Update speed/mode on change") most systems
silently defaulted to SF bus mode 0. Now the mode is always updated,
which causes breakage. It seems most SF which are used as boot media
operate in bus mode 0, so switch that as the default.
This should fix booting at least on Altera SoCFPGA, ST STM32, Xilinx
ZynqMP, NXP iMX and Rockchip SoCs, which recently ran into trouble
with mode 3. Marvell Kirkwood and Xilinx microblaze need to be checked
as those might need mode 3.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Cc: Andreas Biessmann <andreas@biessmann.org>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Valentin Longchamp <valentin.longchamp@hitachi-powergrids.com>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Force the mtd name of spi-nor to "nor" + the driver sequence number:
"nor0", "nor1"... beginning after the existing nor devices.
This patch is coherent with existing "nand" and "spi-nand"
mtd device names.
When CFI MTD NOR device are supported, the spi-nor index is chosen after
the last CFI device defined by CONFIG_SYS_MAX_FLASH_BANKS.
When CONFIG_SYS_MAX_FLASH_BANKS_DETECT is activated, this config
is replaced by to cfi_flash_num_flash_banks in the include file
mtd/cfi_flash.h.
This generic name "nor%d" can be use to identify the mtd spi-nor device
without knowing the real device name or the DT path of the device,
used with API get_mtd_device_nm() and is used in mtdparts command.
This patch also avoids issue when the same NOR device is present 2 times,
for example on STM32MP15F-EV1:
STM32MP> mtd list
SF: Detected mx66l51235l with page size 256 Bytes, erase size 64 KiB, \
total 64 MiB
List of MTD devices:
* nand0
- type: NAND flash
- block size: 0x40000 bytes
- min I/O: 0x1000 bytes
- OOB size: 224 bytes
- OOB available: 118 bytes
- ECC strength: 8 bits
- ECC step size: 512 bytes
- bitflip threshold: 6 bits
- 0x000000000000-0x000040000000 : "nand0"
* mx66l51235l
- device: mx66l51235l@0
- parent: spi@58003000
- driver: jedec_spi_nor
- path: /soc/spi@58003000/mx66l51235l@0
- type: NOR flash
- block size: 0x10000 bytes
- min I/O: 0x1 bytes
- 0x000000000000-0x000004000000 : "mx66l51235l"
* mx66l51235l
- device: mx66l51235l@1
- parent: spi@58003000
- driver: jedec_spi_nor
- path: /soc/spi@58003000/mx66l51235l@1
- type: NOR flash
- block size: 0x10000 bytes
- min I/O: 0x1 bytes
- 0x000000000000-0x000004000000 : "mx66l51235l"
The same mtd name "mx66l51235l" identify the 2 instances
mx66l51235l@0 and mx66l51235l@1.
This patch fixes a ST32CubeProgrammer / stm32prog command issue
with nor0 target on STM32MP157C-EV1 board introduced by
commit b7f060565e ("mtd: spi-nor: allow registering multiple MTDs when
DM is enabled").
Fixes: b7f060565e ("mtd: spi-nor: allow registering multiple MTDs when DM is enabled")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
[trini: Add <dm/device.h> to <mtd.h> for DM_MAX_SEQ_STR]
Signed-off-by: Tom Rini <trini@konsulko.com>
These functions can return errors, it's best to catch them and trigger
the driver unwind code path.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
strncpy() simply bails out when copying a source string whose size
exceeds the destination string size, potentially leaving the destination
string unterminated.
One possible way to address is to pass MDIO_NAME_LEN - 1 and a
previously zero-initialized destination string, but this is more
difficult to maintain.
The chosen alternative is to use strlcpy(), which properly limits the
copy len in the (srclen >= size) case to "size - 1", and which is also
more efficient than the strncpy() byte-by-byte implementation by using
memcpy. The destination string returned by strlcpy() is always NULL
terminated.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
strncpy() simply bails out when copying a source string whose size
exceeds the destination string size, potentially leaving the destination
string unterminated.
One possible way to address is to pass MDIO_NAME_LEN - 1 and a
previously zero-initialized destination string, but this is more
difficult to maintain.
The chosen alternative is to use strlcpy(), which properly limits the
copy len in the (srclen >= size) case to "size - 1", and which is also
more efficient than the strncpy() byte-by-byte implementation by using
memcpy. The destination string returned by strlcpy() is always NULL
terminated.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
strncpy() simply bails out when copying a source string whose size
exceeds the destination string size, potentially leaving the destination
string unterminated.
One possible way to address is to pass MDIO_NAME_LEN - 1 and a
previously zero-initialized destination string, but this is more
difficult to maintain.
The chosen alternative is to use strlcpy(), which properly limits the
copy len in the (srclen >= size) case to "size - 1", and which is also
more efficient than the strncpy() byte-by-byte implementation by using
memcpy. The destination string returned by strlcpy() is always NULL
terminated.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
strncpy() simply bails out when copying a source string whose size
exceeds the destination string size, potentially leaving the destination
string unterminated.
One possible way to address is to pass MDIO_NAME_LEN - 1 and a
previously zero-initialized destination string, but this is more
difficult to maintain.
The chosen alternative is to use strlcpy(), which properly limits the
copy len in the (srclen >= size) case to "size - 1", and which is also
more efficient than the strncpy() byte-by-byte implementation by using
memcpy. The destination string returned by strlcpy() is always NULL
terminated.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
strncpy() simply bails out when copying a source string whose size
exceeds the destination string size, potentially leaving the destination
string unterminated.
One possible way to address is to pass MDIO_NAME_LEN - 1 and a
previously zero-initialized destination string, but this is more
difficult to maintain.
The chosen alternative is to use strlcpy(), which properly limits the
copy len in the (srclen >= size) case to "size - 1", and which is also
more efficient than the strncpy() byte-by-byte implementation by using
memcpy. The destination string returned by strlcpy() is always NULL
terminated.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
strncpy() simply bails out when copying a source string whose size
exceeds the destination string size, potentially leaving the destination
string unterminated.
One possible way to address is to pass MDIO_NAME_LEN - 1 and a
previously zero-initialized destination string, but this is more
difficult to maintain.
The chosen alternative is to use strlcpy(), which properly limits the
copy len in the (srclen >= size) case to "size - 1", and which is also
more efficient than the strncpy() byte-by-byte implementation by using
memcpy. The destination string returned by strlcpy() is always NULL
terminated.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
strncpy() simply bails out when copying a source string whose size
exceeds the destination string size, potentially leaving the destination
string unterminated.
One possible way to address is to pass MDIO_NAME_LEN - 1 and a
previously zero-initialized destination string, but this is more
difficult to maintain.
The chosen alternative is to use strlcpy(), which properly limits the
copy len in the (srclen >= size) case to "size - 1", and which is also
more efficient than the strncpy() byte-by-byte implementation by using
memcpy. The destination string returned by strlcpy() is always NULL
terminated.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
strncpy() simply bails out when copying a source string whose size
exceeds the destination string size, potentially leaving the destination
string unterminated.
One possible way to address is to pass MDIO_NAME_LEN - 1 and a
previously zero-initialized destination string, but this is more
difficult to maintain.
The chosen alternative is to use strlcpy(), which properly limits the
copy len in the (srclen >= size) case to "size - 1", and which is also
more efficient than the strncpy() byte-by-byte implementation by using
memcpy. The destination string returned by strlcpy() is always NULL
terminated.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
strncpy() simply bails out when copying a source string whose size
exceeds the destination string size, potentially leaving the destination
string unterminated.
One possible way to address is to pass MDIO_NAME_LEN - 1 and a
previously zero-initialized destination string, but this is more
difficult to maintain.
The chosen alternative is to use strlcpy(), which properly limits the
copy len in the (srclen >= size) case to "size - 1", and which is also
more efficient than the strncpy() byte-by-byte implementation by using
memcpy. The destination string returned by strlcpy() is always NULL
terminated.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
strncpy() simply bails out when copying a source string whose size
exceeds the destination string size, potentially leaving the destination
string unterminated.
One possible way to address is to pass MDIO_NAME_LEN - 1 and a
previously zero-initialized destination string, but this is more
difficult to maintain.
The chosen alternative is to use strlcpy(), which properly limits the
copy len in the (srclen >= size) case to "size - 1", and which is also
more efficient than the strncpy() byte-by-byte implementation by using
memcpy. The destination string returned by strlcpy() is always NULL
terminated.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
strncpy() simply bails out when copying a source string whose size
exceeds the destination string size, potentially leaving the destination
string unterminated.
One possible way to address is to pass MDIO_NAME_LEN - 1 and a
previously zero-initialized destination string, but this is more
difficult to maintain.
The chosen alternative is to use strlcpy(), which properly limits the
copy len in the (srclen >= size) case to "size - 1", and which is also
more efficient than the strncpy() byte-by-byte implementation by using
memcpy. The destination string returned by strlcpy() is always NULL
terminated.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
strncpy() simply bails out when copying a source string whose size
exceeds the destination string size, potentially leaving the destination
string unterminated.
One possible way to address is to pass MDIO_NAME_LEN - 1 and a
previously zero-initialized destination string, but this is more
difficult to maintain.
The chosen alternative is to use strlcpy(), which properly limits the
copy len in the (srclen >= size) case to "size - 1", and which is also
more efficient than the strncpy() byte-by-byte implementation by using
memcpy. The destination string returned by strlcpy() is always NULL
terminated.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
strncpy() simply bails out when copying a source string whose size
exceeds the destination string size, potentially leaving the destination
string unterminated.
One possible way to address is to pass MDIO_NAME_LEN - 1 and a
previously zero-initialized destination string, but this is more
difficult to maintain.
The chosen alternative is to use strlcpy(), which properly limits the
copy len in the (srclen >= size) case to "size - 1", and which is also
more efficient than the strncpy() byte-by-byte implementation by using
memcpy. The destination string returned by strlcpy() is always NULL
terminated.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
strncpy() simply bails out when copying a source string whose size
exceeds the destination string size, potentially leaving the destination
string unterminated.
One possible way to address is to pass MDIO_NAME_LEN - 1 and a
previously zero-initialized destination string, but this is more
difficult to maintain.
The chosen alternative is to use strlcpy(), which properly limits the
copy len in the (srclen >= size) case to "size - 1", and which is also
more efficient than the strncpy() byte-by-byte implementation by using
memcpy. The destination string returned by strlcpy() is always NULL
terminated.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
strncpy() simply bails out when copying a source string whose size
exceeds the destination string size, potentially leaving the destination
string unterminated.
One possible way to address is to pass MDIO_NAME_LEN - 1 and a
previously zero-initialized destination string, but this is more
difficult to maintain.
The chosen alternative is to use strlcpy(), which properly limits the
copy len in the (srclen >= size) case to "size - 1", and which is also
more efficient than the strncpy() byte-by-byte implementation by using
memcpy. The destination string returned by strlcpy() is always NULL
terminated.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
strncpy() simply bails out when copying a source string whose size
exceeds the destination string size, potentially leaving the destination
string unterminated.
One possible way to address is to pass MDIO_NAME_LEN - 1 and a
previously zero-initialized destination string, but this is more
difficult to maintain.
The chosen alternative is to use strlcpy(), which properly limits the
copy len in the (srclen >= size) case to "size - 1", and which is also
more efficient than the strncpy() byte-by-byte implementation by using
memcpy. The destination string returned by strlcpy() is always NULL
terminated.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
strncpy() simply bails out when copying a source string whose size
exceeds the destination string size, potentially leaving the destination
string unterminated.
One possible way to address is to pass MDIO_NAME_LEN - 1 and a
previously zero-initialized destination string, but this is more
difficult to maintain.
The chosen alternative is to use strlcpy(), which properly limits the
copy len in the (srclen >= size) case to "size - 1", and which is also
more efficient than the strncpy() byte-by-byte implementation by using
memcpy. The destination string returned by strlcpy() is always NULL
terminated.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The two should be equivalent, but at the moment some platforms
(ls1021a-tsn.dts) use phy-mode only, which is not parsed.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Currently the init_phy function may overwrite the priv->interface
property, since it calls tsec_get_interface which tries to determine it
dynamically based on default register values in ECNTRL.
Let's do that only if phy-connection-type happens to not be defined in
the device tree.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The felix driver runs only on NXP LS1028A, which most definitely does
not support the parallel 10G interface, just USXGMII, and that only up
to 2.5Gbps (toned down from 10 Gbps via symbol replication).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The enetc driver runs only on NXP LS1028A, which most definitely does
not support the parallel 10G interface, just USXGMII, and that only up
to 2.5Gbps (toned down from 10 Gbps via symbol replication).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
After the discussion here:
https://lore.kernel.org/netdev/20210603143453.if7hgifupx5k433b@pali/
which resulted in this patch:
https://patchwork.kernel.org/project/netdevbpf/patch/20210704134325.24842-1-pali@kernel.org/
and many other discussions before it, notably:
https://patchwork.kernel.org/project/linux-arm-kernel/patch/1512016235-15909-1-git-send-email-Bhaskar.Upadhaya@nxp.com/
it became apparent that nobody really knows what "SGMII 2500" is.
Certainly, Freescale/NXP hardware engineers name this protocol
"SGMII 2500" in the reference manuals, but the PCS devices do not
support any "SGMII" specific features when operating at the speed of
2500 Mbps, no in-band autoneg and no speed change via symbol replication
. So that leaves a fixed speed of 2500 Mbps using a coding of 8b/10b
with a SERDES lane frequency of 3.125 GHz. In fact, "SGMII 2500 without
in-band autoneg and at a fixed speed" is indistinguishable from
"2500base-x without in-band autoneg", which is precisely what these NXP
devices support.
So it just appears that "SGMII 2500" is an unclear name with no clear
definition that stuck.
As such, in the Linux kernel, the drivers which use this SERDES protocol
use the 2500base-x phy-mode.
This patch converts U-Boot to use 2500base-x too, or at least, as much
as it can.
Note that I would have really liked to delete PHY_INTERFACE_MODE_SGMII_2500
completely, but the mvpp2 driver seems to even distinguish between SGMII
2500 and 2500base-X. Namely, it enables in-band autoneg for one but not
the other, and forces flow control for one but not the other. This goes
back to the idea that maybe 2500base-X is a fiber protocol and SGMII-2500
is an MII protocol (connects a MAC to a PHY such as Aquantia), but the
two are practically indistinguishable through everything except use case.
NXP devices can support both use cases through an identical configuration,
for example RX flow control can be unconditionally enabled in order to
support rate adaptation performed by an Aquantia PHY. At least I can
find no indication in online documents published by Cisco which would
point towards "SGMII-2500" being an actual standard with an actual
definition, so I cannot say "yes, NXP devices support it".
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
To avoid a warning with W=1 about this function not having a previous
prototype, declare it as static, because it is not used outside of this
translation module.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
NXP Legal insists that the following are not fine:
- Saying "NXP Semiconductors" instead of "NXP", since the company's
registered name is "NXP"
- Putting a "(c)" sign in the copyright string
- Putting a comma in the copyright string
The only accepted copyright string format is "Copyright <year-range> NXP".
This patch changes the copyright headers in the networking files that
were sent by me, or derived from code sent by me.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Make sure that the link status returned by phy_startup() is propagated
to the .start() method of struct eth_ops.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Tested-by: Michael Walle <michael@walle.cc>
It is an unfortunate reality that some PHY settings done by U-Boot
persist even after the PHY is reset and taken over by Linux, and even
more unfortunate that Linux has come to depend on things being set in a
certain way.
For example, on the NXP LS1028A-RDB, the felix switch ports are
connected to a VSC8514 QSGMII PHY. Between the switch port PCS and the
PHY, the U-Boot drivers enable in-band auto-negotiation which makes the
copper-side negotiated speed and duplex be transmitted from the PHY to
the MAC automatically.
The PHY driver portion that does this is in vsc8514_config():
/* Enable Serdes Auto-negotiation */
phy_write(phydev, MDIO_DEVAD_NONE, PHY_EXT_PAGE_ACCESS,
PHY_EXT_PAGE_ACCESS_EXTENDED3);
val = phy_read(phydev, MDIO_DEVAD_NONE, MIIM_VSC8514_MAC_SERDES_CON);
val = val | MIIM_VSC8574_MAC_SERDES_ANEG;
phy_write(phydev, MDIO_DEVAD_NONE, MIIM_VSC8514_MAC_SERDES_CON, val);
The point is that in-band autoneg should be turned on in both the PHY
and the MAC, or off in both the PHY and the MAC, otherwise the QSGMII
link will be broken.
And because phy_config() is currently called at .port_enable() time, the
result is that ports on which traffic has been sent in U-Boot will have
in-band autoneg enabled, and the rest won't.
It can be argued that the Linux kernel should not assume one way or
another and just reinitialize everything according to what it expects,
and that is completely fair. In fact, I've already started an attempt to
remove this dependency, although admittedly I am making slow progress at
it:
https://patchwork.kernel.org/project/netdevbpf/cover/20210212172341.3489046-1-olteanv@gmail.com/
Nonetheless, the sad reality is that NXP also has, apart from kernel
drivers, some user space networking (DPDK), and for some reason, the
expectation there is that somebody else initializes the PHYs. The kernel
can't do it because the device ownership doesn't belong to the kernel,
so what remains is for the bootloader to do it (especially since other
drivers generally call phy_config() at probe time). This is a really
weak guarantee that might break at any time, but apparently that is
enough for some.
Since initializing the ports and PHYs at probe time does not break
anything, we can just do that.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Tested-by: Michael Walle <michael@walle.cc>
No one is calling this function from outside felix_switch.c.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Tested-by: Michael Walle <michael@walle.cc>
Non DM builds fail with the following error:
drivers/net/tsec.c:641:24: error: 'tsec_get_interface' defined but not used [-Werror=unused-function]
641 | static phy_interface_t tsec_get_interface(struct tsec_private *priv)
Fix that.
Signed-off-by: Ramon Fried <rfried.dev@gmail.com>
In commit b24bb99d cp110 configuration initially done in u-boot
was removed and delegated to atf firmware as smc call.
That commit didn't account for later introduced in d13b740c SATA invert polarity support.
This patch adds support of passing SATA invert polarity flags to atf
firmware during the smc call.
Signed-off-by: Denis Odintsov <shiva@mail.ru>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Rabeeh Khoury <rabeeh@solid-run.com>
Cc: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Remove the driver st_smic.c used in SPEAr products and the associated
config CONFIG_ST_SMI; this driver is no more used in U-Boot after the
commit 570c3dcfc1 ("arm: Remove spear600 boards and the rest of SPEAr
support").
Fixes: 570c3dcfc1 ("arm: Remove spear600 boards and the rest of SPEAr support")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
The KBUILD_BASENAME contains just the name of the compiled module,
in this case 'sequencer', rather than a full path to the compiled
file. Use it to prevent pulling the full path into the U-Boot binary,
which is useless and annoying.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
This adds support for the DWC_sub31 controllers such as those
found on Apple's M1 SoC. This version of the controller
seems to work fine with the existing driver.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Allow using different PHY interfaces for multiple USB controllers. When no
value is set in DT, we fall back to CONFIG_MXC_USB_PORTSC for now to stay
compatible with current board configurations.
This also adds support for the HSIC mode of the i.MX7.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Import usb_phy_interface enum values and DT match strings from the Linux
kernel.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Some platforms, like the Allwinner H6, do not have a separate glue layer
around the dwc3. Instead, they rely on the clocks/resets/phys referenced
from the dwc3 DT node itself. Add support for enabling the clocks/resets
referenced from the dwc3 DT node.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Resetting an XHCI controller inside xhci_register undoes any register
setup performed by the platform driver. And at least on the Allwinner
H6, resetting the XHCI controller also resets the PHY, which prevents
the controller from working. That means the controller must be taken out
of reset before initializing the PHY, which must be done before calling
xhci_register.
The logic in the XHCI core was added to support the Raspberry Pi 4
(although this was not mentioned in the commit log!), which uses the
xhci-pci platform driver. Move the reset logic to the platform driver,
where it belongs, and where it cannot interfere with other platform
drivers.
This also fixes a failure to call reset_free if xhci_register failed.
Fixes: 0b80371b35 ("usb: xhci: Add reset controller support")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This driver is needed for XHCI to work on the Allwinner H6 SoC. The
driver is copied from Linux v5.10.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
nand_dt_init() is still using fdtdec_xx() interface.
If OF_LIVE flag is enabled, dt property can't be get anymore.
Updating all fdtdec_xx() interface to ofnode_xx() to solve this issue.
For doing this, node parameter type must be ofnode.
First idea was to convert "node" parameter to ofnode type inside
nand_dt_init() using offset_to_ofnode(node). But offset_to_ofnode()
is not bijective, in case OF_LIVE flag is enabled, it performs an assert().
So, this leads to update nand_chip struct flash_node field from int to
ofnode and to update all nand_dt_init() callers.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
The controller may need to have clocks/resets enabled for it to work.
Add support for this. Since the clocks/resets are optional on some
platforms (per the device tree binding), do not prevent probing the
controller if they are missing.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
The Linux i2c driver supports i2c-scl-rising-time-ns,
and i2c-scl-falling-time-ns, but U-Boot uses hard-coded values
for these values.
Update the calculation by fetching them from the device tree if
present and use the previous values as the default if they are
missing.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
We have individual SOC symbols for each keystone 2 platform. Use the
existing CONFIG_ARCH_KEYSTONE rather than CONFIG_SOC_KEYSTONE to
encompass all of the keystone families.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_OMAP_EHCI_PHY1_RESET_GPIO
CONFIG_OMAP_EHCI_PHY2_RESET_GPIO
CONFIG_OMAP_EHCI_PHY3_RESET_GPIO
To do this, we also introduce CONFIG_HAS_CONFIG_OMAP_EHCI_PHYn_RESET_GPIO
options to get setting the GPIO number.
Signed-off-by: Tom Rini <trini@konsulko.com>
Move the main option for handling drivers/dma/keystone_nav* to Kconfig,
and enable it by default. All of the sub-symbols are not configurable,
so remove them from the CONFIG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
The COFNIG_KEYSTONE_RBL_NAND option is always enabled for the driver on
keystone platforms, but not older davinci platforms. Use def_bool for
the symbol. For CONFIG_KEYSTONE_NAND_MAX_RBL_PAGE, it's only used within
the driver and derived from another symbol, so remove CONFIG from the
name. Finally, CONFIG_KEYSTONE_NAND_MAX_RBL_SIZE is a bit more fixed.
For now, use the value directly. Long term, as part of DM'ifying NAND,
this should come from the device tree.
Signed-off-by: Tom Rini <trini@konsulko.com>
At this point in time, all platforms that had previously used
drivers/usb/phy/omap_usb_phy.c have been migrated to DM and related
options. Remove this now unused code and some related unused defines.
Signed-off-by: Tom Rini <trini@konsulko.com>
This is only used in the aemif driver that is otherwise currently
keystone2 centric. Moving forward, if this is applicable to some other
platform then such base addresses should be able to be obtained via the
device tree. Use KS2_AEMIF_CNTRL_BASE directly now rather than
indirectly.
Signed-off-by: Tom Rini <trini@konsulko.com>
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmFR2fMRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreaAnAf/ZKPy3CRphbgAmbLhNQhQGpLosLcFp343
cv53gfsv1DakLRrhqMSnOQSVoTg9P22uHbooDDR9WHfZyEL6tvGZ+dgN2/wlDhDj
wbvvsM7FB+uvLVfMF3MURQBvy4dPO+FyCm/uHmry2V2uqWPw4ss+aVhxeQ5s4/oI
LpS6yaiM8UAj2GTUZSqJ1+/W7YG9N6tL73n0PDyCvSrdCkyPWqpww1rtST88SfFI
bBEWc6ksna/29haOwHQ2xopEbVxtHv2byULfqUtnsbtE4Ozw8o0fx66tdwPHTQlM
7eSuRiEbqjlJuUZFIbMat7nb7inZkaWupZ/Sr1HUUiDdKMygrRsQhg==
=x8Uf
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-next-27sep21' of https://source.denx.de/u-boot/custodians/u-boot-dm into next
Various of-platdata improvements, including CONFIG_OF_REAL
In commit b24bb99d cp110 configuration initially done in u-boot
was removed and delegated to atf firmware as smc call.
That commit didn't account for later introduced in d13b740c SATA invert polarity support.
This patch adds support of passing SATA invert polarity flags to atf
firmware during the smc call.
Signed-off-by: Denis Odintsov <shiva@mail.ru>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Rabeeh Khoury <rabeeh@solid-run.com>
Cc: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Some PCIe controller's read_config() method support indicating error
directly via return value, but some cannot distinguish all-ones (or
all-zeros) read response from an error.
The current code in pci_bind_bus_devices() interprets all-ones /
all-zeros in PCI_VENDOR_ID register as "nothing connected", and
continues the cycle, but an error returned via return value breaks the
cycle.
This is wrong for the PCIe controllers which return this error via
return value.
Handle all errors when reading PCI_VENDOR_ID the same way.
This fixes enumeration of PCI devices for example when there is a PCI
bridge connected behind another PCI bridge and not all ports are
connected to a device, and the controller (for example Aardvark)
translates the UR error (Unsupported Request) as -EOPNOTSUPP.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The cpu nodes in arch/sandbox/dts/test.dts should conform to the devicetree
specification:
* property device_type must be set to "cpu"
* the reg property must be provided
* the cpu nodes must have an address
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support for accessing GPIOs using of-plata. This uses the same
mechanism as for clocks, but allows use of the xlate() method so that
the driver can interpret the parameters.
Update the condition for GPIO_HOG so that it is not built into SPL,
since it needs SPL_OF_REAL which is not enabled in sandbox_spl.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function is available but not exported. More generally it does not
really work as intended.
Reimplement it and add a sandbox test too.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is actually a misnomer now, since the phandle info may contain
a driver_info index or a udevice index. Rename it to use the word
'phandle', which seems more accurate. Add a comment while we are here.
Also add a test for this function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Convert some of these occurences to C code, where it is easy to do. This
should help encourage this approach to be used in new code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Use the livetree API for this driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Now that we have a 'positive' Kconfig option, use this instead of the
negative one, which is harder to understand.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current API is outdated as it requires a devicetree pointer.
Move these functions to use the ofnode API and update this globally. Add
some tests while we are here.
Correct the call in exynos_dsim_config_parse_dt() which is obviously
wrong.
Signed-off-by: Simon Glass <sjg@chromium.org>
Use the more generic reset-gpios property name.
Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Remove the driver st_smic.c used in SPEAr products and the associated
config CONFIG_ST_SMI; this driver is no more used in U-Boot after the
commit 570c3dcfc1 ("arm: Remove spear600 boards and the rest of SPEAr
support").
Fixes: 570c3dcfc1 ("arm: Remove spear600 boards and the rest of SPEAr support")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Lower 4 bits of PCI_MEMORY_BASE and PCI_MEMORY_LIMIT registers are reserved
and should be zero. So do not set them to non-zero value.
Lower 4 bits of PCI_PREF_MEMORY_BASE and PCI_PREF_MEMORY_LIMIT registers
contain information if 64-bit memory addressing is supported. So preserve
this information when overwriting these registers.
Lower 4 bits of PCI_IO_BASE and PCI_IO_LIMIT register contain information
if 32-bit io addressing is supported. So preserve this information and do
not try to configure 32-bit io addressing (via PCI_IO_BASE_UPPER16 and
PCI_IO_LIMIT_UPPER16 registers) when it is unsupported.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmFKxpEcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyBLaB/0XsIdkGAvcHLWW8yUg
27GiRznikNKwn9/qIj2ByraoUd4BvxdQV4gKHR1R9n0sgYh/8VMyLbmhRoCRKFwP
3mQ0MUyjaeU5sEWzasovJVpXhuUapEiV0jEg6t3Lgwd3mp2QK2Pk87zoleQfZNkb
VAVCnt1T+kb3y0W9oa3XZbuH2wam9T5pNWRGW70JbgzdwJNKLO1Qo7MfcUNiDxJu
Jf7uXtYwwILlN38G1KSk1ymMjfaotCqj7RzNaV3Ero57MVj3VzerKGb7H+XPOYf2
nYXyietYLJJkzvHzSDwIdCSVlOSQL8QqVB8GCmLiNQD4tG830RcvSJnYpRLylWQK
6F+Y
=Q/aS
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2022.01-a' of https://source.denx.de/u-boot/custodians/u-boot-at91 into next
First set of u-boot-at91 features for the 2022.01 cycle:
This feature set includes : the support for CPU driver for arm926
(sam9x60 device); changes required for OP-TEE boot for sama5d2_xplained
and sama5d27_som1_ek boards; QSPI boot configuration for sama5d2_icp;
starting to remove old Kconfig unused symbols from config_whitelist.txt
(work will take more time); also small fixes and updates in mach, DT,
configs, etc.
The KBUILD_BASENAME contains just the name of the compiled module,
in this case 'sequencer', rather than a full path to the compiled
file. Use it to prevent pulling the full path into the U-Boot binary,
which is useless and annoying.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
This adds support for the DWC_sub31 controllers such as those
found on Apple's M1 SoC. This version of the controller
seems to work fine with the existing driver.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Allow using different PHY interfaces for multiple USB controllers. When no
value is set in DT, we fall back to CONFIG_MXC_USB_PORTSC for now to stay
compatible with current board configurations.
This also adds support for the HSIC mode of the i.MX7.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Import usb_phy_interface enum values and DT match strings from the Linux
kernel.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Some platforms, like the Allwinner H6, do not have a separate glue layer
around the dwc3. Instead, they rely on the clocks/resets/phys referenced
from the dwc3 DT node itself. Add support for enabling the clocks/resets
referenced from the dwc3 DT node.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Resetting an XHCI controller inside xhci_register undoes any register
setup performed by the platform driver. And at least on the Allwinner
H6, resetting the XHCI controller also resets the PHY, which prevents
the controller from working. That means the controller must be taken out
of reset before initializing the PHY, which must be done before calling
xhci_register.
The logic in the XHCI core was added to support the Raspberry Pi 4
(although this was not mentioned in the commit log!), which uses the
xhci-pci platform driver. Move the reset logic to the platform driver,
where it belongs, and where it cannot interfere with other platform
drivers.
This also fixes a failure to call reset_free if xhci_register failed.
Fixes: 0b80371b35 ("usb: xhci: Add reset controller support")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This driver is needed for XHCI to work on the Allwinner H6 SoC. The
driver is copied from Linux v5.10.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The crystal, CPU and master clock were not displayed correctly on SAM9X60
after adding CCF clock support. Add compatible for ARM926EJ-S to fix
this.
Reported-by: Eugen Hristev <eugen.hristev@microchip.com>
Fixes: a64862284f ("clk: at91: sam9x60: add support compatible with CCF")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Split master clock in 2 controlling block: one for prescaler one for
divider. This will allow referencing correctly the CPU clock and
master clock in device trees.
Reported-by: Eugen Hristev <eugen.hristev@microchip.com>
Fixes: a64862284f ("clk: at91: sam9x60: add support compatible with
CCF")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
reset_*_bulk expects a real pointer.
Fixes: 4f7abafe1c ("driver: watchdog: reset watchdog in designware_wdt_stop() function")
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The K3 SoCs have some PLL output clocks (POSTDIV clocks) which in
turn serve as inputs to other HSDIV output clocks. These clocks use
the actual value to compute the divider clock rate, and need to be
registered with the CLK_DIVIDER_ONE_BASED flags. The current k3-clk
driver and data lacks the infrastructure to pass in divider flags.
Update the driver and data to account for these divider flags.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
There are three different divider values in the DIV_CTRL register
controlled by the k3-pll driver. Currently the ti_pll_clk_set_rate
function writes the entire register when programming plld, even though
plld only resides in the lower 6 bits.
Change the plld programming to read-modify-write to only affect the
relevant bits for plld and to preserve the other two divider values
present in the upper 16 bits, otherwise they will always get set to zero
when programming plld.
Fixes: 0aa2930ca1 ("clk: add support for TI K3 SoC PLL")
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Header file version.h does not use anything from timestamp.h. Including of
timestamp.h has side effect which cause recompiling object file at every
make run because timestamp.h changes at every run.
So remove timestamp.h from version.h and include timestamp.h in files
which needs it.
This change reduce recompilation time of final U-Boot binary when U-Boot
source files were not changed as less source files needs to be recompiled.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Add in lib/acpi/acpi_table.c and test/dm/acpi.c, rework a few others]
Signed-off-by: Tom Rini <trini@konsulko.com>
More C files do not use compile time timestamp macros and do not have to be
recompiled every time when SOURCE_DATE_EPOCH changes.
This patch moves version_string[] from version.h to version_string.h and
updates other C files which only needs version_string[] string to include
version_string.h instead of version.h. After applying this patch these
files are not recompiled every time when SOURCE_DATE_EPOCH changes.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
With legacy PCI code removed and thus DM_PCI also removed, a few places
did not get correctly updated with the merge to next and thus broke.
Remove now extraneous dependencies on DM_PCI.
Signed-off-by: Tom Rini <trini@konsulko.com>
Some SoCs (as seen on A20) seem to misreport the MMC FIFO level if the
FIFO is completely full: the level size reads as zero, but the FIFO_FULL
bit is set. We won't do a single iteration of the read loop in this
case, so will be stuck forever.
Check for this situation and use a safe minimal FIFO size instead when
we hit this case.
This fixes MMC boot on A20 devices after the MMC FIFO optimisation
(9faae5457f).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Support using mmc command for enumerating mmc card in a given mode
Fix device_remove in mmc
Fix switch issue with send_status disabled
Drop 1ms delay in fsl_esdhc command sending
Revert "mmc: sdhci: set to INT_DATA_END when there are data"
Since the beginning of this driver which was initially for the MPC8379
and MPC8536 SoCs, there is this spurious 1ms delay. According to the
comment it should actually be only 8 clock cycles. Esp. during EFI block
transfers, this 1ms add up to a significant delay and slows down EFI
boot.
I couldn't find any mention in the MPC8536 that there should be a delay
of 8 clock cycles between commands. The SD card specification mentions that
the clock has to be left enabled for 8 cycles after a command or
response. But I don't see how this delay will help with this.
Go ahead and just remove it. If there will ever be any regression we can
introduce a compile time flag, but for now I'd like to keep it simple.
In the split off imx driver this delay was also removed in commit
9098682200 ("mmc: fsl_esdhc_imx: remove the 1ms delay before sending
command").
Signed-off-by: Michael Walle <michael@walle.cc>
HS400_ES is missed when down grade to HS mode during
device_remove the mmc device
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
When send_status is false or wait_dat0 is not supported, the switch
function should not send CMD13 but directly return.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Add support for enumerating MMC card in a given mode using mmc rescan and
mmc dev commands. The speed mode is provided as the last argument in these
commands and is indicated using the index from enum bus_mode in
include/mmc.h. A speed mode can be set only if it has already been enabled
in the device tree.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
This reverts commit 17ea3c8628.
In eMMC specification, for the response-with-busy(R1b, R5b)
command, the DAT0 will driven to LOW as BUSY status, and in
sdhci specification, the transfer complete bit should be wait
for BUSY status de-assert.
All response-with-busy commands don't contain data, the data
judgement is no need.
Signed-off-by: Yuezhang.Mo <Yuezhang.Mo@sony.com>
Reviewed-by: Andy Wu <Andy.Wu@sony.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Use dev_dbg() instead of dev_err() in pcie_advk_check_pio_status().
For example CRS is not an error status, it just says that the request
should be retried.
Without this, U-Boot spams the terminal with
pcie_advk pcie@d0070000: Non-posted PIO Response Status: UR, 0xc80 @ 0x100000
pcie_advk pcie@d0070000: Non-posted PIO Response Status: UR, 0xc80 @ 0x108000
pcie_advk pcie@d0070000: Non-posted PIO Response Status: UR, 0xc80 @ 0x110000
pcie_advk pcie@d0070000: Non-posted PIO Response Status: UR, 0xc80 @ 0x120000
pcie_advk pcie@d0070000: Non-posted PIO Response Status: UR, 0xc80 @ 0x128000
pcie_advk pcie@d0070000: Non-posted PIO Response Status: UR, 0xc80 @ 0x130000
...
when a device is not connected to a PCIe switch (Unsupported Request
from the switch).
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
While a board could have multiple SATA ports, some of the ports might
not have a disk attached to them. So while probing for disks,
sata_mv_probe() should continue probing all ports, and skip one with
no disk attached.
Tests with:
- Seagate Goflex Net (Marvell Kirkwood 88F6281) out-of-tree u-boot.
- Zyxel NSA325 (Marvell Kirkwood 88F6282 out-of-tree u-boot.
Observation:
If a board has 2 or more SATA ports, and there is only one disk
attached to one of the ports, sata_mv_probe() does not return
a successful probe status. And if only one disk is attached to the
2nd port (i.e. port 1), it is not probed at all.
Patch Description:
Let sata_mv_probe() continues probing all ports, even if there
is error in probing a given port, and then return a successful
status if there is at least one port was probed successfully.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
According to PCIe base specification, if CRS Software Visibility is not
enabled, the Root Complex must re-issue the Configuration Request as a new
Request.
Normally this part of Root Complex is implemented in hardware but aardvark
is somehow special and does not implement it in hardware and expect that
handling of config requests are fully implemented in software.
This re-issuing functionality is required also because U-Boot does not
support CRS Software Visibility feature and therefore expects that Root
Complex re-issues requests as is specified in PCIe base specification.
Retry / re-issue config request up to the PIO_MAX_RETRIES, to prevent
infinite loop. After retry count exceed PIO_MAX_RETRIES, returns failure.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
There was mistake in commit 4cd61c43fd ("arm: a37xx: pci: Fix handling
PIO config error responses"). U-Boot does not support handling of CRS
return value for PCI_VENDOR_ID config read request and also does not set
CRSSVE bit.
Therefore disable returning CRS response for now.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: 4cd61c43fd ("arm: a37xx: pci: Fix handling PIO config error responses")
Reviewed-by: Stefan Roese <sr@denx.de>
calculate_hash() would try to select the appropriate hashing function
by a if/elseif contruct. But that is exactly why hash_lookup_algo()
exists, so use it instead.
This does mean that we now have to 'select HASH' to make sure we get
the hash_lookup_algo() symbol. However, the change makes sense because
even basic FITs will have to deal with "hash" nodes.
My only concern is that the 'select SPL_HASH' might cause some
platform to grow above its SPL size allowance
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
[trini: Make FSL_CAAM be implied only on ARM && SPL]
Signed-off-by: Tom Rini <trini@konsulko.com>
This driver is currently responsible for enabling all ccache ways.
Composable cache could be configure as RAM or cache, we will use it as
RAM at the beginning to put the u-boot SPL there. In u-boot proper
phrase, we will use the composable cache as cache, and try to enable the
cache ways.
Signed-off-by: Zong Li <zong.li@sifive.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
The ocores_i2c.c driver is missing a sentinel at the end of
the compatible strings list. This causes the "dm compat" command
to spew garbage.
Signed-off-by: Thomas Skibo <thomas-git@skibo.net>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The code under drivers/net is related to ethernet networking drivers, in
some fashion or another. Drop these from the top-level Makefile and
also move the phy rule into drivers/net/Makefile which is where it
belongs. Make the new rule for drivers/net check for the build-stage
relevant ETH symbol.
Fix up some Kconfig dependencies while we're here to mirror how the
Makefile logic now works.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Introduce ETH, Kconfig dependency changes, am43xx fix]
Signed-off-by: Tom Rini <trini@konsulko.com>
Move the power/ rules into drivers/power to avoid clutter in the Makefile
and drivers/Makefile files.
We must select SPL_POWER if SPL_POWER_DOMAIN is used, since the two are
currently independent and boards do not necessarily enable SPL_POWER.
Add a TPL_POWER as well, as that is used by one board.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
At present we have SPL_POWER but not piain POWER. This works because
there is a special build rule in Makefile that always includes the
drivers/power directory.
It is better to have all driver directories included by drivers/Makefile
and there is already a rule in there for this purpose. It just needs a
Kconfig for U-Boot proper, so add one.
Update the pmic.h header file so that it defines the old pmic struct
always, when driver model is not in use. That will avoid build errors
for boards which enable POWER but not DM_PMIC.
Enable this option always. That seems strange at first sight, but it
actually but mimics the current Makefile behaviour. Once we can drop the
old PMICs it should be easy enough to rename DM_PMIC to POWWER, or
something similar.
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_POWER_I2C
CONFIG_POWER_LEGACY
They are handled at the same time due to a dependency between them.
Update the Makefile rule to use legacy power only in U-Boot proper.
Unfortunately a separate rule is needed in SPL to be able to build
legacy power. Add SPL related symbols for both, to allow for SPL-only
usage.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
[trini: More SPL related cleanups, reword commit message]
Signed-off-by: Tom Rini <trini@konsulko.com>
This option is used in pre-driver model code and much of it has never
been converted to driver model.
We want to add a new option to enable power support, so we can use a
simple rule in the Makefile. Rename this one, which is really about
a particular implementation of power.
Also update the pmic.h header file so it either includes the legacy
API or the driver model one.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Add a proper Kconfig option for SPL so we can remove the hack in some of
the board config files.
This involves adding CONFIG_SPL_DM_PMIC to some of the configs as well
as updateing the Makefile rule for PMIC_RK8XX to exclude SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
[trini: Add SPL_PMIC_RK8XX, enable when needed, handle undef of
CONFIG_DM_PMIC_PFUZE100 as well]
Signed-off-by: Tom Rini <trini@konsulko.com>
At present we have SPL_GPIO and TPL_GPIO but not piain GPIO. This
works because there is a special build rule in Makefile that always
includes the drivers/gpio directory.
It is better to have all driver directories included by drivers/Makefile
and there is already a rule in there for this purpose. It just needs a
Kconfig for U-Boot proper, so add one.
Enable the option always for now, since this mimics current behaviour.
This can be updated once DM_GPIO is used everywhere.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is not a good idea to use things called CONFIG_xxx in the source code
since this prefix is reserved for use by Kconfig. Rename these variables.
Signed-off-by: Simon Glass <sjg@chromium.org>
We cannot use the existing DMA config for the MCD driver because it is
not migrated to driver model. In order to move it to drivers/Makefile
we need some sort of option for it. Add a new DMA_LEGACY option, which
also acts as a signal that it should be migrated.
Enable this for devkit3250 which uses CONFIG_DMA_LPC32XX which is not
converted to Kconfig.
For now this is not used in the Makefile. That update happens in a
following patch.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rename this option so that CONFIG_IS_ENABLED can be used with it.
Oddly there is already an SPL_CACHE option. Drop it in favour of this one.
Drop the special SPL Makefile rule which is now superfluous.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we have SPL_SERIAL and TPL_SERIAL but not piain SERIAL. This
works because there is a special build rule in Makefile that always
includes the drivers/serial directory.
It is better to have all driver directories included by drivers/Makefile
and there is already a rule in there for this purpose. It just needs a
Kconfig for U-Boot proper, so add one.
It is always enabled, for now, since that mimics the current behaviour.
It should be possible to drop the strange 'SERIAL_PRESENT' option at some
point and use SERIAL instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rename these options so that CONFIG_IS_ENABLED can be used with them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
[trini: Fixup some incorrect renames]
Signed-off-by: Tom Rini <trini@konsulko.com>
DMA is aligned to ARCH_DMA_MINALIGN(64 bytes), but as per spec, alignment
required is 4bytes only. Change DMA alignment from ARCH_DMA_MINALIGN to
GQSPI_DMA_ALIGN. Remove alignment of data length in non-exponential case.
Some minor improvements in the initialization to initialize gen_fifo
threshold and disable qspi controller while setting config register.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Current implementation uses auto mode for starting generic FIFO.
The recommendation from IP designers is to use manual mode, hence
change to manual start mode.
In fill genfifo first write to genfio and then trigger manual start.
Also enable and check for genfifo empty interrupt status in place of
genfifo not full interrupt.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This new option allows to disable ahci-pci driver in SPL. Disabling it is
needed when SPL_PCI is not enabled as ahci-pci depends on PCI.
This change fixes following compile error when CONFIG_SPL_SATA_SUPPORT is
enabled and SPL_PCI is disabled.
LD spl/u-boot-spl
arm-linux-gnueabihf-ld.bfd: drivers/ata/ahci.o: in function `ahci_probe_scsi_pci':
drivers/ata/ahci.c:1205: undefined reference to `dm_pci_map_bar'
arm-linux-gnueabihf-ld.bfd: drivers/ata/ahci.c:1215: undefined reference to `dm_pci_read_config16'
arm-linux-gnueabihf-ld.bfd: drivers/ata/ahci.c:1216: undefined reference to `dm_pci_read_config16'
arm-linux-gnueabihf-ld.bfd: drivers/ata/ahci.c:1220: undefined reference to `dm_pci_map_bar'
make[1]: *** [scripts/Makefile.spl:512: spl/u-boot-spl] Error 1
make: *** [Makefile:1977: spl/u-boot-spl] Error 2
LD spl/u-boot-spl
arm-linux-gnueabihf-ld.bfd: drivers/ata/ahci-pci.o: in function `ahci_pci_probe':
drivers/ata/ahci-pci.c:21: undefined reference to `ahci_probe_scsi_pci'
make[1]: *** [scripts/Makefile.spl:512: spl/u-boot-spl] Error 1
make: *** [Makefile:1977: spl/u-boot-spl] Error 2
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
File drivers/ata/ahci-pci.c calls function ahci_probe_scsi_pci() which is
compiled only when DM_PCI is enabled. So add missing dependency into
Kconfig.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
The ds1307 driver also supports the DS1339 and DS1340.
However, in ds1307_rtc_reset the register writes assume that the chip
is a DS1307. This is evident in the writing of bits SQWE, RS1, RS0 to
the control register. While this applies correctly to the DS1307, on a
DS1340 the control register doesn't contain those bits (instead, the
register is used for clock calibration). By writing these bits the
clock calibration will be changed and the chip can become
non-functional after a reset call.
Signed-off-by: Callum Sinclair <callum.sinclair@alliedtelesis.co.nz>
Add purely software-implmented drivers to support multiple
hash operations including CRC, MD5, and SHA family.
This driver is based on the new hash uclass.
Signed-off-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
Add UCLASS_HASH for hash driver development. Thus the
hash drivers (SW or HW-accelerated) can be developed
in the DM-based fashion.
Signed-off-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
default n/no doesn't need to be specified. It is default option anyway.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[trini: Rework FSP_USE_UPD portion]
Signed-off-by: Tom Rini <trini@konsulko.com>
- Guard most of the options in drivers/ddr/fsl/Kconfig with
SYS_FSL_DDR || SYS_FSL_MMDC.
- Migrate FSL_DMA, DDR_ECC, DDR_ECC_CMD, and ECC_INIT_VIA_DDRCONTROLLER
to Kconfig.
- Clean up the logic for including the DDR_ECC_CMD code.
Signed-off-by: Tom Rini <trini@konsulko.com>
As this symbol can either be a fixed value or the function
get_board_ddr_clk, migration is tricky. Introduce a choice of DYNAMIC
or STATIC_DDR_CLK_FREQ. If DYNAMIC, we continue to use the board
defined get_board_ddr_clk function. If STATIC, set CONFIG_DDR_CLK_FREQ
to that value and now include/clock_legacy.h contains the function
prototype or defines get_board_ddr_clk() to that static value. Update
callers to test for DYNAMIC or STATIC.
Signed-off-by: Tom Rini <trini@konsulko.com>
Move the symbol that controls building some JEDEC SPD support functions
to Kconfig. This is required on the TI keystone 2 platforms and very
frequently (but not always) used on large number of Freescale/NXP
platforms, so use imply there.
Signed-off-by: Tom Rini <trini@konsulko.com>
We have a number of CONFIG symbols to express the fixed size of system
memory. For now, rename CONFIG_DDR_FIXED_SIZE to CONFIG_SYS_SDRAM_SIZE
and adjust usage to match that CONFIG_SYS_SDRAM_SIZE expects the entire
size rather than MiB.
Cc: Marek Behún <marek.behun@nic.cz>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Marek Behún <marek.behun@nic.cz>
A rather common kind of external watchdog circuit is one that is kept
alive by toggling a gpio. Add a driver for handling such a watchdog.
The corresponding linux driver apparently has support for some
watchdog circuits which can be disabled by tri-stating the gpio, but I
have never actually encountered such a chip in the wild; the whole
point of adding an external watchdog is usually that it is not in any
way under software control. For forward-compatibility, and to make DT
describe the hardware, the current driver only supports devices that
have the always-running property. I went a little back and forth on
whether I should fail ->probe or only ->start, and ended up deciding
->start was the right place.
The compatible string is probably a little odd as it has nothing to do
with linux per se - however, I chose that to make .dts snippets
reusable between device trees used with U-Boot and linux, and this is
the (only) compatible string that linux' corresponding driver and DT
binding accepts. I have asked whether one should/could add "wdt-gpio"
to that binding, but the answer was no:
https://lore.kernel.org/lkml/CAL_JsqKEGaFpiFV_oAtE+S_bnHkg4qry+bhx2EDs=NSbVf_giA@mail.gmail.com/
If someone feels strongly about this, I can certainly remove the
"linux," part from the string - it probably wouldn't the only place where
one can't reuse a DT snippet as-is between linux and U-Boot.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
A board can have and make use of more than one watchdog device, say
one built into the SOC and an external gpio-petted one. Having
wdt-uclass only handle the first is both a little arbitrary and
unexpected.
So change initr_watchdog() so we visit (probe) all DM watchdog
devices, and call the init_watchdog_dev helper for each.
Similarly let watchdog_reset() loop over the whole uclass - each
having their own ratelimiting metadata, and a separate "is this device
running" flag.
This gets rid of the watchdog_dev member of struct global_data. We
do, however, still need the GD_FLG_WDT_READY set in
initr_watchdog(). This is because watchdog_reset() can get called
before DM is ready, and I don't think we can call uclass_get() that
early.
The current code just returns 0 if "getting" the first device fails -
that can of course happen because there are no devices, but it could
also happen if its ->probe call failed. In keeping with that, continue
with the handling of the remaining devices even if one fails to
probe. This is also why we cannot use uclass_probe_all().
If desired, it's possible to later add a per-device "u-boot,autostart"
boolean property, so that one can do CONFIG_WATCHDOG_AUTOSTART
per-device.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Since the watchdog_dev member of struct global_data is going away in
favor of the wdt-uclass handling all watchdog devices, prepare for
that by adding a helper to call wdt_stop() on all known devices.
If an error is encountered, still do wdt_stop() on remaining devices,
but remember and return the first error seen.
Initially, this will only be used in one single
place (board/alliedtelesis/x530/x530.c).
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
As a step towards handling all DM watchdogs in watchdog_reset(), use a
per-device flag to keep track of whether the device has been started
instead of a bit in gd->flags.
We will still need that bit to know whether we are past
initr_watchdog() and hence have populated gd->watchdog_dev -
incidentally, that is how it was used prior to commit 9c44ff1c5f.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
In preparation for handling all DM watchdogs in watchdog_reset(), pull
out the code which handles starting (or not) the gd->watchdog_dev
device.
Include the device name in various printfs.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
The addition of .pre_probe and .per_device_auto made this look
bad. Fix it.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
As preparation for having the wdt-uclass provided watchdog_reset()
function handle all DM watchdog devices, and not just the first such,
introduce a uclass-owned struct to hold the reset_period and
next_reset, so these become per-device instead of being static
variables.
No functional change intended.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
wdt_start() does the "no ->start? return -ENOSYS" check, don't
open-code that in wdt_expire_now().
Also, wdt_start() maintains some global (and later some per-device)
state, which would get out of sync with this direct method call - not
that it matters much here since the board is supposed to reset very
soon.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
These symbols are now either unused or were only used within the config
file to determine other logic, which could be done in a way that doesn't
further pollute the CONFIG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
The value CONFIG_ALTERA_SPI_IDLE_VAL is never re-defined by a board.
Rename this to ALTERA_SPI_IDLE_VAL.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This driver uses the CONFIG namespace to set the chips internal CONFIG
namespace related bits. However, CONFIG is reserved for the top-level
Kconfig based configuration system. Use CFG as the namespace here
instead to avoid pollution.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This driver uses the CONFIG namespace to set the chips internal CONFIG
namespace related bits. However, CONFIG is reserved for the top-level
Kconfig based configuration system. Use CFG as the namespace here
instead to avoid pollution.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
- As there are no boards that use different values for speed / slave on
different buses, use a single option.
- Switch to using the common SYS_I2C_SPEED / SYS_I2C_SLAVE options.
- Introduce _HAS_ options for additional buses as only the first one is
common to all users.
- Convert all remaining symbols to Kconfig.
Signed-off-by: Tom Rini <trini@konsulko.com>
- Migrate SYS_I2C_SH and related defines to Kconfig
- Remove currently unused SYS_I2C_SH related defines
- Cleanup related README section.
Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_I2C_MXC
CONFIG_SYS_I2C_MXC_I2C1
CONFIG_SYS_I2C_MXC_I2C2
CONFIG_SYS_I2C_MXC_I2C3
CONFIG_SYS_I2C_MXC_I2C4
Signed-off-by: Tom Rini <trini@konsulko.com>
The omap24xx I2C driver uses its own CONFIG namespace for common I2C
variables. Rather than convert more of them to Kconfig, rename these to
the common I2C ones and remove the entirely unused functionality. As
part of this, we make the am335x_shc platforms consistent with their
intended speed values.
Signed-off-by: Tom Rini <trini@konsulko.com>
There are no users of more than 1 i2c bus in the non-DM case currently.
Remove the additional defines for this.
Signed-off-by: Tom Rini <trini@konsulko.com>
Convert SYS_I2C_EARLY_INIT to Kconfig, and make it depend on
SPL_SYS_I2C_LEGACY. Remove the weak implementation as it's either
something that needs to exist for real, or shouldn't be called.
Signed-off-by: Tom Rini <trini@konsulko.com>
First, we convert CONFIG_SYS_I2C_LEGACY to Kconfig. Next, as you cannot
have SYS_I2C_LEGACY and DM_I2C at the same time, introduce
CONFIG_SPL_SYS_I2C_LEGACY so that we can enable the legacy option only
in SPL. Finally, for some PowerPC cases we also need
CONFIG_TPL_SYS_I2C_LEGACY support. Convert all of the existing users to
one or more symbols.
Signed-off-by: Tom Rini <trini@konsulko.com>
Currently the legacy software i2c support is only used for a single bus.
Remove all of the extra and unused support. Also update the README to
not reference that, and finish removing some already badly auto-edited
related text.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_I2C_SOFT
CONFIG_SYS_I2C_SOFT_SPEED
CONFIG_SYS_I2C_SOFT_SLAVE
Signed-off-by: Tom Rini <trini@konsulko.com>
- Rename usages of CONFIG_SYS_DEF_EEPROM_ADDR to CONFIG_SYS_I2C_EEPROM_ADDR
based on current usage.
- Convert CONFIG_SYS_I2C_EEPROM_ADDR, CONFIG_SYS_I2C_EEPROM_ADDR_LEN,
CONFIG_SYS_I2C_EEPROM_BUS, CONFIG_CONFIG_SYS_EEPROM_SIZE
CONFIG_SYS_EEPROM_PAGE_WRITE_BITS and CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS
to Kconfig. We move these symbols around a bit and add appropriate
dependencies to them. In some cases, we now add a correct default value
as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
Finish moving this driver to Kconfig.
- Update the dependency logic for Exynos5 too
- Remove the unused CONFIG_SYS_I2C_S3C24X0_SPEED variable
- Drop CONFIG_SYS_I2C_S3C24X0_SLAVE as it's always set to 0.
- Move the internal SYS_I2C_S3C24X0_SLAVE define closer to the only user.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
There are a number of DWC2 configuration options that are set in dwc2.h
and referenced in dwc2.c only. Move these out of the CONFIG_DWC2
namespace and in to the DWC2 namespace. Note that hikey was defining an
option that was already always enabled, so we can remove that hunk.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
xilinx:
- Disable CONFIG_ARCH_FIXUP_FDT_MEMORY
- Print information about cpu via soc drivers and enable DISPLAY_CPUINFO
- Wire infrastructure for DTB_RESELECT and MULTI_DTB_FIT
zynq:
- Wire single QSPI
- Use power-source instead of io-standard properties
- Enable nor on zc770-xm012
zynqmp:
- Change handling around multi_boot()
- Setup offset for u-boot.itb in spi
- Generate run time dfu_alt_info for capsule update
- Use explicit values for enums (zynqmp_firmware.h)
- Enable RTC/SHA1/BUTTON/BUTTON_GPIO command
- Disable WDT driver by default
- Bind usb/scsi via preboot because of EFI
- DT updates/fixes
- Add soc driver
- Fix SPL SPI boot mode
versal:
- Add soc driver
sdhci:
- Update tap delay programming for zynq_sdhci driver
cmd:
- Fix RTC uclass handling in date command
- Update pwm help message
- Update reset help message
watchdog:
- Fix wwdt compilation
rtc:
- Deal with seq alias in rtc uclass
- Add zynqmp RTC driver
fdt:
- Add kernel-doc for fdt_fixup_memory_banks()
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYSilpgAKCRDKSWXLKUoM
Id2JAJ9jY19JiEpOd3vuRCT5CE/pzX4yDACeP8DiXDzSi5tLHwDWUCBobUTze2s=
=5lnj
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2021.10-rc3' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2021.10-rc3
xilinx:
- Disable CONFIG_ARCH_FIXUP_FDT_MEMORY
- Print information about cpu via soc drivers and enable DISPLAY_CPUINFO
- Wire infrastructure for DTB_RESELECT and MULTI_DTB_FIT
zynq:
- Wire single QSPI
- Use power-source instead of io-standard properties
- Enable nor on zc770-xm012
zynqmp:
- Change handling around multi_boot()
- Setup offset for u-boot.itb in spi
- Generate run time dfu_alt_info for capsule update
- Use explicit values for enums (zynqmp_firmware.h)
- Enable RTC/SHA1/BUTTON/BUTTON_GPIO command
- Disable WDT driver by default
- Bind usb/scsi via preboot because of EFI
- DT updates/fixes
- Add soc driver
- Fix SPL SPI boot mode
versal:
- Add soc driver
sdhci:
- Update tap delay programming for zynq_sdhci driver
cmd:
- Fix RTC uclass handling in date command
- Update pwm help message
- Update reset help message
watchdog:
- Fix wwdt compilation
rtc:
- Deal with seq alias in rtc uclass
- Add zynqmp RTC driver
fdt:
- Add kernel-doc for fdt_fixup_memory_banks()
dev_dbg, dev_err and dev_warn seems to be moved to different header file.
Include dm/device_compat.h file to compile properly.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
soc_xilinx_versal driver allows identification of family & revision
of versal SoC. This driver is selected by CONFIG_SOC_XILINX_VERSAL.
Probe this driver using platdata U_BOOT_DEVICE structure which is
defined at mach-versal/cpu.c.
Add this config to xilinx_versal_virt_defconfig &
xilinx_versal_mini_ospi_defconfig file to select this driver.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Reviewed-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
soc_xilinx_zynqmp driver allows identification of family & revision
of zynqmp SoC. This driver is selected by CONFIG_SOC_XILINX_ZYNQMP.
Add this config to xilinx_zynqmp_virt_defconfig file.
Probe this driver using platdata U_BOOT_DEVICE structure which is
specified in mach-zynqmp/cpu.c.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Reviewed-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Since set_control_reg is available in sdhci.c, use it and remove
arasan_sdhci_set_control_reg().
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
As per SD spec when SD host controller is reset, it takes 1000msec
to detect the card state. In case, if we enable the sd bus voltage &
card detect state is not stable, then host controller will disable
the sd bus voltage.
In case of warm/subsystem reboot, due to unstable card detect state
host controller is disabling the sd bus voltage to sd card causing
sd card timeout error. So we wait for a maximum of 1000msec to get
the card detect state stable before we enable the sd bus voltage.
This current fix is workaround for now, this needs to be analysed
further. Zynqmp platform should behave the same as Versal, but we
did not encounter this issue as of now. So we are fixing it for
Versal only.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Move tapdelay function calls to zynq_sdhci.c and make them static
inline. zynqmp_tap_delay.h has function prototypes for the functions
defined in tap_delays.c, which will not be needed anymore.
Remove tap_delays.c and zynqmp_tap_delay.h files.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Currently xilinx sdhci driver is using zynqmp_mmio_write() to set
tapdelay values and DLL resets. Continue to use this for SPL and mini
U-Boot where U-Boot will be executed at EL3 level.
Use firmware call xilinx_pm_request() using appropriate arguments to
set input/output tapdelays and also for DLL resets in regular flow(EL2).
Host driver should explicitly request DLL reset before ITAP (assert DLL)
and after OTAP (release DLL) to avoid issues in some cases. Also handle
error return where possible.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The DDR subsystem in Diamond Mesa is consisted of controller, PHY,
memory reset manager and memory clock manager.
Configuration settings of controller, PHY and memory reset manager
is come from DDR handoff data in bitstream, which contain the register
base addresses and user settings from tool.
Configuration settings of memory clock manager is come from the HPS
handoff data in bitstream, however the register base address is defined
in device tree.
The calibration is fully done in HPS, which requires IMEM and DMEM
binaries loading to PHY SRAM for running this calibration, both
IMEM and DMEM binaries are also part of bitstream, this bitstream
would be loaded to OCRAM by SDM, and configured by DDR driver.
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Minimum 1GB memory size is required in current memory test, so this patch
improves the memory test for processing memory size less than 1GB, and
the size in power of two.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
fsl-qoriq: Fixes related to env, spi, usb, crypto, configs, distro-boot
for Layerscape Boards like lx2, sl28, ls2088ardb.
powerpc: Fixes for t208xrdb revd board and cortina related configs
update for T208xRDB, T4240RDB.
i2c changes for for-v2021.10-rc3
new driver:
- Introduce mcp230xx support
from Sebastian Reichel
new feature:
- i2c-gpio: add support for "sda-gpios" + "scl-gpios" i2c-gpio bindings.
from Samuel Holland
- bootcount: add a new driver with syscon as backend
from Nandor Han
The driver will use a syscon regmap as backend and supports both
16 and 32 size value. The value will be stored in the CPU's endianness.
Signed-off-by: Nandor Han <nandor.han@vaisala.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
To avoid confusion about the order of the GPIOs, the i2c-gpio binding
was updated to use a separate property for each GPIO instead of an
array. However, the driver only supports the old binding. Add support
for the new binding as well, so the driver continues to work as device
trees are updated.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Introduce driver for I2C based MCP230xx GPIO chips, which are
quite common and already well supported by the Linux kernel.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add function to apply a bitmask to an i2c register, so
that specific bits can be cleared and/or set.
Suggested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
'gpt' and 'mmc0' fastboot partitions have been treated as the same device,
but it is wrong.
Fill disk_partition structure with eMMC user partition info
to properly flash data.
Signed-off-by: Oleh Kravchenko <oleg@kaa.org.ua>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Sean Anderson <sean.anderson@seco.com>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
The current U-Boot version has the next matches for boot partitions:
> mmc0boot0 to EMMC_BOOT1
> mmc0boot1 to EMMC_BOOT1 (should be EMMC_BOOT2)
This patch fixes a typo for the boot partition number.
Signed-off-by: Oleh Kravchenko <oleg@kaa.org.ua>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Marek Vasut <marex@denx.de>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
One of the "dma_addr_t" instances was left out when
converting to "caam_dma_addr_t".
Fixes: 2ff17d2f74 ("crypto: fsl: refactor for 32 bit version CAAM support on ARM64")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add support for boards supporting TFA boot separately in cortina
firmware. Please note, a weak function is defined to retrieve firmware
address values as CONFIG_CORTINA_FW_ADDR is now defined in defconfig and
can only have one possible value defined. This weak function will help
in overwrting the values to get proper addresses as per boot source.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Use moveconfig.py script to convert below defines to Kconfig and move
these entries to defconfigs.
CONFIG_CORTINA_FW_ADDR
CONFIG_CORTINA_FW_LENGTH
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Import linux commit 007773e16a6f ("spi: nxp-fspi: Ensure width is
respected in spi-mem operations") to fix SPI access on boards which
don't have all SPI I/O lines connected to the flash.
Since commit 71025f013c ("mtd: spi-nor-core: Rework hwcaps selection")
u-boot figures out the capabilities by looking at spi_mem_supports_op().
The FlexSPI driver doesn't take the board layout into account. Fix that.
Fixes: 383fded70c ("spi: nxp_fspi: new driver for the FlexSPI controller")
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add the support of the BSEC clock used by the STM32MP misc driver
since the commit 622c956cad ("stm32mp: bsec: manage clock when present
in device tree") even if this clock is not yet defined in kernel device
tree stm32mp151.dtsi.
This patch avoids issue for basic boot when this secure clock are not
provided by secure world with SCMI.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
