When submitting interrupt packets to an endpoint we only link in the ed
once to avoid some races surrounding unlinking of periodic endpoints,
but we share one ohci_device struct / one set of ed-s for all devices,
which means that if we have an interrupt endpoint at endpoint 1 with one
device, and a non interrupt endpoint 1 with another device we end up
with the same ed linked into both the periodic and async lists, which is
not good (tm).
This commit switches over to using separate ohci_device structs, and thus
separate ed-s for devices with interrupt endpoints, fixing this.
This fixes e.g. matching a usb storage device and keyboard on the same
usb-1 hub not working.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Marek Vasut <marex@denx.de>
This commit adds support for the OHCI companion controller, which makes
usb-1 devices directly plugged into to usb root port work.
Note for now this switches usb-keyboard support for sunxi back from int-queue
support to the old interrupt polling method. Adding int-queue support to the
ohci code and switching back to int-queue support is in the works.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Convert sunxi-boards which use the sunxi-ehci code to the driver-model.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
For some reason the ohci code is full with:
#ifdef DEBUG
pkt_print(...)
#else
mdelay(1);
#endif
AFAICT there is no reason for the mdelay(1) calls. This commit disables them
when building the ohci code for new driver-model using boards. It leaves
the mdelay(1) calls in place when building for older boards, so as to avoid
causing any regressions there.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The usb spec says that we must wait a minimum amount of time after port
power on (exact time is in the hub descriptor), this is something which
we must not only do for root ports but also for external hub ports, which
is why the common usb_hub code already waits a full second after powering
up ports. Having a separate wait for just the root hub in the ohci-hcd
code only leads to doing the waiting twice for the root ports, so drop the
wait from the ohci-hcd code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The u-boot usb code uses polling for all endpoints, including interrupt
endpoints, so urbs should never be automatically resubmitted.
This also fixes a leak of the urb, as submit_int_msg() did not check if
an already re-submitted urb exists before creating a new one.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Marek Vasut <marex@denx.de>
USB scanning is slow, and there is no need to scan the companion buses
if no usb devices where handed over to the companinon controllers by any
of the main controllers.
This saves e.g. 2 seconds when booting a A10 OLinuxIno Lime with no USB-1
devices plugged into the root usb ports.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
USB companion controllers must be scanned after the main controller has
been scanned, so that any devices which the main controller which to hand
over to the companion have actually been handed over before we scan the
companion.
As there are no guarantees that this will magically happen in the right
order, split the scanning of the buses in 2 phases, first main controllers,
and then companion controllers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
Move printing of usb scan status to usb_scan_bus().
This is a preparation patch for adding companion controller support to the
usb uclass.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
Interrupt endpoints typically are polled for a long time by the usb
controller before they return anything, so calls to submit_int_msg() can
take a long time to complete this.
To avoid this the u-boot code has the an interrupt queue mechanism / API,
add support for this to the driver-model usb code and implement it for the
dm ehci code.
See the added doc comments for more details.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
This is a preparation patch for adding interrupt-queue support to the
ehci dm code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
Short circuit the retry loop in legacy_hub_port_reset() by returning an
error from usb_control_msg() when a device was handed over to a companion
by the ehci code. This avoids trying to reset low / fullspeed devices 5
times needlessly. Also do not print an error when a device has been handed
over.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
When after a reset the port status connection bit is still set and the enable
bit is not then we're dealing with a full-speed device and should hand it over
to the companion controller.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Interrupts transfers timing out is normal, so do not log an error for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Marek Vasut <marex@denx.de>
Add proper cache flushing / invalidating for non cache coherent cpus, for now
only enable this for new (driver-model) usb code to avoid regressions.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Non static function and variable declarations do not belong in a .h file.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Marek Vasut <marex@denx.de>
This is a preparation patch for adding driver-model support.
Note we do keep ohci_dev as a separate struct so that we can later add
support for interrupt-queues which requires allocating a separate ohci_dev
per interrupt-queue.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Marek Vasut <marex@denx.de>
devgone is never assigned a value, so the one comparisson reading it will
never be true, and devgone can be completely removed.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Marek Vasut <marex@denx.de>
Without this usb-1 device descriptors do not get read properly.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
The ehci driver model code for finding the first upstream usb-2 hub before
this commit has a number of issues:
1) "if (!ttdev->speed != USB_SPEED_HIGH)" does not work because the '!'
takes presedence over the '!=' this should simply be
"if (ttdev->speed == USB_SPEED_HIGH)"
2) It makes ttdev point to the first upstream usb-2 hub, but ttdev should
point to the last usb-1 device before the first usb-2 hub (when going
upstream from the device), as ttdev is used to find the port of the
first usb-2 hub to which the the last usb-1 device is connected.
3) parent_devnum however should be set to the devnum of the first usb-2
hub, so we need to keep pointers around to both usb_device structs.
To complicate things further during enumeration usb_device.dev will point
to the parent udevice, where as during normal use it will point to
the actual udevice, we must handle both cases correctly.
This commit fixes all this making usb-1 devices attached to usb-2 hubs,
including usb-1 devices attached to usb-1 hubs attached to usb-2 hubs, work.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
Use usb_get_bus in dm ehci code rather then re-implementing it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
Currently we copy over a number of usb_device values stored in the on stack
struct usb_device probed in usb_scan_device() to the final driver-model managed
struct usb_device in usb_child_pre_probe() through usb_device_platdata, and
then call usb_select_config() to fill in the rest.
There are 3 problems with this approach:
1) It does not fill in enough fields before calling usb_select_config(),
specifically it does not fill in ep0's maxpacketsize causing a div by zero
exception in the ehci driver.
2) It unnecessarily redoes a number of usb requests making usb probing slower
3) Calling usb_select_config() a second time fails on some usb-1 devices
plugged into usb-2 hubs, causing u-boot to not recognize these devices.
This commit fixes these issues by removing (*) the usb_select_config() call
from usb_child_pre_probe(), and instead of copying over things field by field
through usb_device_platdata, store a pointer to the in stack usb_device
(which is still valid when usb_child_pre_probe() gets called) and copy
over the entire struct.
*) Except for devices which are explictly instantiated through device-tree
rather then discovered through usb_scan_device() such as emulated usb devices
in the sandbox.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
Make usb_get_bus easier to use for callers, by directly returning the bus
rather then returning it via a pass-by-ref argument.
This also removes the error checking from the current callers, as
we already have an assert() for bus not being NULL in usb_get_bus().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
Do not use bus->seq before device_probe(bus), as bus->seq is not set until
after the device_probe() call. This fixes u-boot printing: "USB-1: " for
each bus it scans.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add a delay of 1 microsecond before issuing soft reset to the
controller to let ongoing ULPI transaction complete.
This prevents corruption of ULPI Function Control Register which
eventually prevents phy clock from entering to low power mode
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The 2/3 usb-phys on the sunxi SoCs are really a single separate functional
block, and are modelled as such in devicetree. So once we've moved all the
sunxi usb code to the driver-model then phy_probe will be called once
for the entire block from the driver-model enumeration code.
Move to this now as this also avoids problems with phy_probe being called
multiple times once we introduce ohci support. This also allows us to get rid
of the sunxi_usb_phy_enabled_count variable as phy_probe now is guaranteed
to be called only once.
Since we're effectively rewriting the probe / remove functions, move them
to the end of the file while we are at it, as that is the most logical place
for them.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The usbc.? files now only contain usb-phy related code, rename them to make
this clear.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Rename the sunxi_usbc_foo functions to sunxi_usb_phy_bar to make it clear
that these are usb-phy functions. Also change the verbs & nouns in the suffix
to match the verbs & nouns used in the Linux kernels generic phy framework.
This patch purely renames things, it contains no functional changes.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
This is the only function left in sunxi/usbc.c which is not phy related,
so remove it.
This is a preparation patch for turning the usbc.c code into a proper
usb phy driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The sunxi "usbc" code is mostly about phy setup, but currently also sets up
the host controller clocks, which is something which really belongs in the
host controller drivers, so move it there.
This is a preparation patch for moving the sunxi ehci code to the driver
model and for adding ohci support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Check if USB Erratum A005697 is applicable on BSC913x and
add corresponding property in the device tree via device
tree fixup which is used by linux driver
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Identify soc(s) having dual phy so as to add "utmi_dual" as phy_mode
for all these socs. This is required for supporting deel-sleep feature
in linux for usb driver
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add driver model support in the XHCI support code so that it can be used by
XHCI USB drivers.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Since driver model will want to use most of the same code for XHCI init
and uninit, put it in a separate function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
This function should not be delving into struct usb_device. Pass in the
parameters it needs directly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
This function should not be delving into struct usb_device. Pass in the
parameters it needs directly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Rather than getting this directly from struct usb_device, call a function
to obtain it. This will make it possible for driver model to provide it
another way.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
We want to use mostly the same init and uninit code for driver model, so move
the common part into two functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Try to return useful error numbers where possible. Also avoid swallowing
an error number when it is returned by a called function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
This variable is a bit of a hack. We can obtain the same information from
the normal device config. This will fit better with driver model, where
global variables are best avoided.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
This driver supports using emulation devices to provide a USB bus within
sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
These devices must have their addresses removed ready for the next USB
bus enumeration. Add this logic to usb_stop().
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Some controllers support OTG (on-the-go) where they can operate as either
host or device. The gadget layer in U-Boot supports this.
While this layer does not interact with driver model, we can provide a
function which sets up the controller in the correct way. This way the code
at least builds (although it likely will not work).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
At present USB devices with no driver model driver cannot be seen in the
device list, and we fail to set them up correctly. This means they cannot
be used.
While having real drivers that support driver model for all USB devices
is the eventual goal, we are not there yet.
As a stop-gap, add a generic USB driver which is bound when we do not have
a real driver. This allows the device to be set up and shown on the bus.
It also allows ad-hoc code (such as usb_ether) to find these devices and
set them up.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
USB devices in U-Boot are currently probed only after all devices have
been enumerated. Each type of device is probed by custom code, e.g.:
- USB storage
- Keyboard
- Ethernet
With driver model this approach doesn't work very well. We could build
a picture of the bus and then go back and add the devices later, but
this means that the data structures are incomplete for quite a while.
It also does not follow the model of being able to bind a device when we
discover it.
We would prefer to have devices automatically be bound as the device is
enumerated. This allows us to attach drivers to particular USB classes
or product/vendor IDs. This is the method used by Linux.
Add the required #defines from Linux, a way of declaring a USB driver and
the logic to locate the correct driver given the USB device's descriptors.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Add a way for EHCI controller drivers to support driver model. Drivers can
call ehci_register() to register themselves in their probe() methods.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
The index cannot be used with driver model, and isn't needed anyway. Change
the parameter to a pointer.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
These are a pain with driver model because we might have different EHCI
drivers which want to implement them differently. Now that they use
consistent function signatures, we can in good conscience move them to
a struct.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Fix non-driver-model EHCI to set up the EHCI operations correctly:
Signed-off-by: Tom Rini <trini@konsulko.com>
Move the bulk of the code in usb_lowlevel_init() into a separate function
which will also be used by driver model. Keep the CONFIG options out of
this function by providing a tweak flag for Faraday. We need to avoid using
CONFIG options in driver model code where possible, since it makes it
impossible to use multiple controllers in that code where they have
different options.
The CONFIG_EHCI_HCD_INIT_AFTER_RESET option is also kept out of the
common init function. With driver model the controller will be able to
perform this extra init itself after registering with the EHCI layer.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
With driver model we want to remove the controller pointer in struct udevice
and use driver model data structures instead. To prepare for this, move
access to this field to a function which can provide a different
implementation for driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Adjust this function so that it is passed an EHCI controller pointer so that
implementations can look up their controller. This makes the weak functions
use a consistent API.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Adjust this function so that it is passed an EHCI controller pointer so that
implementations can look up their controller. This makes the weak functions
use a consistent API.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
We don't need this anymore, so adjust the code to avoid using it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Adjust this function so that it is passed an EHCI controller pointer so that
implementations can look up their controller.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
At present the tegra driver uses a separate pointer to know which controller
type is in use. This works because only one controller type is used at a
time.
With driver model we want to make the controller state hermetic in the sense
that it is not necessary to look elsewhere to know the controller type. This
will permit a controller to implement the EHCI weak functions without
reference to global data structures.
To achieve this, define an enum for the controller type and store it with
the information on each EHCI controller.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Add a private data pointer that clients of EHCI can use to access their
private information. This establishes a link between struct ehci_ctrl and
its associated controller data structure.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Adjust this function so that it is passed an EHCI controller pointer so that
implementations can look up their controller.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Put these at the top of the file so they are in one place. Also add function
prototypes to the header file to avoid call site mismatches.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Add a uclass that can represent a USB controller. For now we do not create
devices for things attached to the controller. This will be added later.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
IIUC, interrupt transfers are NAK'd by devices until they wish to trigger
an interrupt, and e.g. EHCI controllers retry these in HW until they are
ACK'd. However, DWC2 doesn't seem to retry, so we need to do this in SW.
In practice, I've seen DWC2_HCINT_FRMOVRUN happen too. I'm not quite sure
what this error implies; perhaps it's related to how near the end of a
USB frame we're at when the interrupt transfer is initiated? Anyway,
retrying this temporary error seems to be necessary too.
With all these commits applied, both my USB keyboards (one LS Lenovo and
one FS Dell) work correctly when there is no USB hub between the SoC and
the keyboard; We still need split transactions to be implemented for hubs
to work.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
As best I can tell, there's no difference between bulk and interrupt
transfers in terms of how the HW should be programmed, at least given
that we're executing one transaction at a time rather than scheduling
them into frames for maximum throughput.
This patch ends up sharing the toggle bit state between bulk and
interrupt transfers on a particular EP. However I believe this is fine;
AFAIK a given EP either uses bulk or interrupt transfers and doesn't mix
them.
This patch doesn't do anything with the "interval" parameter for
interrupt transfers, but then most other USB controller drivers in U-Boot
don't either.
It turns out that one of my keyboards is happy to work using control
transfers but the other only gives non-zero "HID reports" via interrupt
transfers.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
A bit must be set in HCCHAR when communicating with low-speed devices.
I have no idea why there's no corresponding bit to distinguish between
full-speed and high-speed devices, but no matter; they all work now!
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
This doesn't make my LS keyboard work any better, but it does at least
report the correct speed in "usb tree".
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Use of these APIs is required on the Raspberry Pi. With this change, USB
on RPi1 should be more reliable, and USB on the RPi2 will start working.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
When I created wait_for_chhltd(), I noticed that some instances of the
code it replaced expected the ACK bit to be set and others didn't. I
assumed this was an accidental inconsistency in the code, so wrote
wait_for_chhltd() to always expect ACK to be set. This code appeared to
work correctly for both enumeration of USB keyboards and operation of
USB Ethernet devices. However, this change broke USB Mass Storage (at
least my USB SD card reader). This change reverts to exactly the
original behaviour. I'm not sure why the ACK bit isn't always set
(perhaps a quirk in the USB HW or DWC2 controller), but the code works
this way!
Fixes: 5be4ca7d6ac8 ("usb: dwc2: unify waiting for transfer completion")
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Each USB transfer is split up into chunks that are held in an aligned
buffer. This imposes a limit on the size of each chunk, but no limit on
the total size of transferred data. Fix the logic in chunk_msg() not to
reject large transfers, but simply take the size of the aligned buffer
into account when calculating the chunk size.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
The original aligned_buffer usage:
a) Uselessly copied data into the aligned buffer even for IN
transactions. Fix this my making the copy conditional.
b) Always programmed the HW to transfer to/from the start of the aligned
buffer. This worked fine for OUT transactions since the memcpy copied
the OUT data to this location too. However, for large IN transactions,
since the copy from the aligned buffer to the "client" buffer was
deferred until after all chunks were transferred. it resulted in each
chunk's transfer over-writing the data for the first transfer. Fix
this by copying IN data as soon as it's received.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
The control data toggle resets to DATA1 at the start of the data phase
of every setup transaction. We don't need a global variable to store
the value; we can just store it on the stack.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Move the body of submit_bulk_msg() into new function chunk_msg(). This
can be shared with submit_control_msg() to reduce code duplication, and
allow control messages larger than maxpacket.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
This commit allows xHCI to use both 64 and 32 bit memory
physical addresses depending on architecture it's being built for.
Also it makes use of readq()/writeq() on 64-bit systems
Signed-off-by: Sergey Temerkhanov <s.temerkhanov@gmail.com>
Signed-off-by: Radha Mohan Chintakuntla <rchintakuntla@cavium.com>
Cast pointers to unsigned long instead of a sized 32-bit type to avoid
pointer to integer cast size mismatch warnings.
Cc: Tom Warren <twarren@nvidia.com>
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Change addresses to unsigned long to be compatible with 64-bit builds.
Regardless of fixing warnings, the device is still only 32-bit capable.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Marek Vasut <marex@denx.de>
Panasonic's System LSI products, UniPhier SoC family, have been
transferred to Socionext Inc.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Support xHCI host driver used on Panasonic UniPhier platform.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Marek Vasut <marex@denx.de>
Because uniphier_ehci_reset() is only called from ehci-uniphier.c,
it can be a static function there.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Marek Vasut <marex@denx.de>
Now UniPhier platform highly depends on Device Tree configuration
(CONFIG_OF_CONTROL is select'ed by Kconfig). Since the EHCI is only
used on main U-Boot, we can drop platform devices of the EHCI
controllers. We still keep UART platform devices because they might
be useful for SPL.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Marek Vasut <marex@denx.de>
Since commit 0e7368c6c4 (kbuild: prepare for moving headers into
mach-*/include/mach), we can replace #include <asm/arch/*.h> with
<mach/*.h> so we do not need to create the symbolic link during the
build.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
The dwc3_set_mode function is used only in
drivers/usb/host/xhci-exynos5.c so make it to static.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Add a driver which locates the available XHCI controllers on the PCI bus
and makes them available.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Currently create_int_queue is only implemented by the ehci code, and that
does not honor interrupt intervals, but other drivers which might also want
to implement create_int_queue may honor intervals, so add an interval param.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Most of the usb-controller init code found in ehci-sunxi.c also is necessary
to init the otg usb controller, so move it to a common place.
While at it also update various #ifdefs / defines for sun8i support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Check USB Erratum A007792 applicability. If applicable, add
corresponding property in the device tree via device tree fixup
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add a new framework for fsl usb erratum handling to standardize
erratum checking only inside Uboot. Information to kernel is passed
via a boolean property corresponding to erratum, hence eliminating
need for code duplication inside kernel
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
move usb device tree fixup code from "arch/powerpc/" to "drivers/usb/"
so that it works independent of architecture it is running on
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
If CONFIG_OF_CONTROL is defined, search device tree nodes that are
compatible with "panasonic,uniphier-ehci" and take the base address
from their "reg" property.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Marek Vasut <marex@denx.de>
Set TXFIFOTHRESH to adjust ddr pipeline delay for successful large
usb writes
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
U-Boot has never cared about the type when we get max/min of two
values, but Linux Kernel does. This commit gets min, max, min3, max3
macros synced with the kernel introducing type checks.
Many of references of those macros must be fixed to suppress warnings.
We have two options:
- Use min, max, min3, max3 only when the arguments have the same type
(or add casts to the arguments)
- Use min_t/max_t instead with the appropriate type for the first
argument
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Pavel Machek <pavel@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
[trini: Fixup arch/blackfin/lib/string.c]
Signed-off-by: Tom Rini <trini@ti.com>
Move USB Errata checking code from "arch/powerpc" to architecture independent
file "fsl_usb.h" so that errata(s) become independent of the architecture.
For each erratum checking function for PPC arch, define a nop function for
non PPC arch for successful compilation in either case
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
U-Boot has imported various utility macros from Linux
scattering them to various places without consistency.
In include/common.h are min, max, min3, max3, ARRAY_SIZE, ALIGN,
container_of, DIV_ROUND_UP, etc.
In include/linux/compat.h are min_t, max_t, round_up, round_down,
etc.
We also have duplicated defines of min_t in some *.c files.
Moreover, we are suffering from too cluttered include/common.h.
This commit moves various macros that originate in
include/linux/kernel.h of Linux to their original position.
Note:
This commit simply moves the macros; the macros roundup,
min, max, min2, max3, ARRAY_SIZE are different
from those of Linux at this point.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
CONFIG_CPU_ARM920T was introduced into Kconfig by commit 2e07c249a6
(kconfig: arm: introduce symbol for ARM CPUs).
This commit removes all the defines of CONFIG_ARM920T and replaces the
only reference in drivers/usb/host/ohci-hcd.c with CONFIG_CPU_ARM920T.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
According to EHCI specification, the LSB of DWORD 3 of Queue Head
(Current qTD Pointer) is not T-bit, but always zero.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
This change adds support for enabling the USB host features of the board.
This includes the USB3503A hub and the SMC LAN9730 ethernet controller
as well.
Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
usb_phy_enable should return status bit, but not phy mode bit, thus
add a new function usb_phy_mode to query the PHY for it's mode and
make usb_phy_enable just return 0 but not 'phy_ctrl & USBPHY_CTRL_OTG_ID'.
Include a new board weak function board_usb_phy_mode. If board code
does not reimplement this function, it just call usb_phy_mode and return
usb_phy_mode's return value. The reason to include such a weak function
is: " SOC OTG core <--connect--> board HOST port, but no pin id for
the board host port, so board can not use usb_phy_mode to return the
phy mode, but define it's own rule."
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ye Li <B37916@freescale.com>
Add support for the 2 ehci controllers found on the sun6i (A31) soc.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Marek Vasut <marex@denx.de>
Add proper Kconfig options to select the usb Vbus gpio-s, besides moving to
Kconfig being the right thing to do, an added advantage of this is that it
allows for boards without Vbus gpio-s.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Support EHCI host driver used on Panasonic UniPhier platform.
Since Device Tree is not supported on UniPhier yet, the base address
of USB cores are passed from board files (platdevice.c).
TODO for me:
Move the base address to device trees.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Marek Vasut <marex@denx.de>
CMD_IAAD (Interrupt on Async Advance Doorbell) is bit 6, not bit 5.
While we are here, sort the flags.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
This is necessary for the device-model enabled builds to work properly.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
Mostly automatic with:
sed -i -e 's/CONFIG_\(SUN[45678]I\)/CONFIG_MACH_\1/g' $(git grep -l CONFIG_SUN[45678]I)
followed by removing the relevant #defines from include/configs/sun?i.h by
hand.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
R8A7791, R8A7793 and R8A7794 have same IP of USB controller.
This collect up address data of each SoCs.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
R8A7793 has same IP of USB controller as R8A7791 and R8A7794 of rmobile
ARM SoCs. This adds support R8A7793 to EHCI HCD of rmobile.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Add support of usb xhci. xHCI controls all USB speeds of the Host
mode, that is, the SS through the SS PHY, as well as the HS, FS, and
LS through the USB2 PHY. xHCI replaces and supersedes all previous
host HCIs (HS-only EHCI, FS/LS OHCI and UHCI), and is therefore not
backwards compatible with any of them. The USB3SS’s USB Controller is
fully compliant with xHC.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
This move makes is possible to use this header not only from kirkwood
platforms but from all Marvell mvebu platforms.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
This is the USB host controller used on the Altera SoCFPGA and Raspbery Pi.
This code has three checkpatch warnings, but to make sure it stays at least
readable and clear, these are not fixed. These bugs are in the USB request
handling combinatorial logic, so any abstracting of those is out of question.
Tested on DENX MCV (Altera SoCFPGA 5CSFXC6C6U23C8N) and RPi B+ (BCM2835).
Signed-off-by: Oleksandr Tymoshenko <gonzo@bluezbox.com>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Pavel Machek <pavel@denx.de>
Cc: Vince Bridgers <vbridger@altera.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Trying to enumerate USB devices connected via ULPI to T20 failed as
follows:
USB2: ULPI integrity check failed
Git bisecting revealed the following commit being at odds:
commit 2d34151f75
usb: tegra: refactor PHY type selection
Looking at above commit one quickly identifies a copy paste error which
this patch fixes. Happy ULPIing again (;-p).
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Periodic schedules tracks how many int_queue-s are active, and decides whether
or not to en/disable the periodic schedule based on this. This is clearly
a per controller thing.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
When we first start an int queue, the qh's overlay area is all zeros. This
gets filled by the hc with the actual qtd values as soon as it advances
the queue, but we may call poll_int_queue before then, in which case we
would think the transfer has completed as the hc has not yet copied the
qt_token to the overlay, so the active flag is not set.
This fixes this by checking the actual qtd token, rather then the overlay.
This also fixes a (theoretical) race where we see the completion in the
overlay and free and re-use the qtd before the hc has completed writing back
the overlay to the actual qtd.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
For full / low speed devices we need to get the devnum and portnr of the tt,
so of the first upstream usb-2 hub, not of the parent device (which may be a
usb-1 hub).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The mx6sl/mx6sx has 2 OTG and 1 host. So they have name
"USBO2H_USB_BASE_ADDR" in imx-regs.h. The driver hard codes
the USB base address name to "USBOH3", which causes the driver
failed to build for mx6sl/mx6sx.
This patch uniform the address name to "USB_BASE_ADDR" for all
mx6 series.
Signed-off-by: Ye.Li <B37916@freescale.com>
Add board-specific callbacks for enabling/disabling port power
into the MXS EHCI controller driver. This is in-line with the
names of callbacks on other systems.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
If the SoC has pcr, we use pcr (peripheral control register)
to enable or disable clock.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
If the SoC has pcr, we use pcr (peripheral control register)
to enable or disable clock.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
echi-rmobile does not support xHCI. This removes xHCI address
from address table. And this revise a value of CONFIG_USB_MAX_CONTROLLER_COUNT
for lager board and koelsh board.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
R8A7794 has same IP of USB controller as R8A7790 and R8A7791.
This addes support for R8A7794.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
The Allwinner aka sunxi SoCs have one or more USB host controllers.
This adds a driver for their EHCI.
Signed-off-by: Roman Byshko <rbyshko@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
upper_32_bits() and lower_32_bits() have been ported into linux/compat.h.
Start use them now in drivers/usb/host/xhci.h.
Signed-off-by: Lijun Pan <Lijun.Pan@freescale.com>
This patch returns back support for old ep93xx processors family
Signed-off-by: Sergey Kostanbaev <sergey.kostanbaev@gmail.com>
Cc: albert.u.boot@aribaud.net
Because of the brackets the & and && is evaluated before
the comparison. This is likely not the intention. Change
it to test the first and second condition to both be true.
cc: Marek Vasut <marex@denx.de>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Initialization of r8a66597 info structure is not enough.
Because initilization was used size of pointer.
This fixes that use size of r8a6659 info structure.
Signed-off-by: Yasuhisa Umano <yasuhisa.umano.zc@renesas.com>
This driver is processed as two USB hub despite one.
The number of root hub is defined in R8A66597_MAX_ROOT_HUB.
This fixes that register is accessed by using the definition
of R8A66597_MAX_ROOT_HUB.
Signed-off-by: Yasuhisa Umano <yasuhisa.umano.zc@renesas.com>
Define and use CONTROL_REGISTER_W1C_MASK to make sure that
w1c bits of usb control register do not get reset while
writing any other bit
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
A few changes are made to the Tegra EHCI driver so that it can set
everything up for device-mode operation on the first USB controller.
This can be used in conjunction with ci_udc.c to operate as a USB
device.
Detailed changes are:
* Rename set_host_mode() to set_up_vbus() since that's really what it
does.
* Modify set_up_vbus() to know whether it's initializing in host or
device mode, and:
- Skip the external VBUS check in device mode, since external VBUS is
expected in this case.
- Disable VBUS output in device mode.
* Modify init_phy_mux() to know whether it's initializing in host or
device mode, and hence skip setting USBMODE_CM_HC (which enables host
mode) in device mode. See the comments in that function for why this
is safe w.r.t. the ordering requirements of PHY selection.
* Modify init_utmi_usb_controller() to force "b session valid" in device
mode, since the HW requires this. This is done in UTMI-specific code,
since we only support device mode on the first USB controller, and that
controller can only talk to a UTMI PHY.
* Enhance ehci_hcd_init() to error-check the requested host-/device-mode
vs. the dr_mode (dual-role mode) value present in device tree, and the
HW configurations which support device mode.
* Enhance ehci_hcd_init() not to skip HW initialization when switching
between host and device mode on a controller. This requires remembering
which mode the last initialization used.
Cc: Jim Lin <jilin@nvidia.com>
Cc: Stefan Agner <stefan@agner.ch>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Both init_{utmi,ulpi}_usb_controller() have nearly identical code for
PHY type selection. Pull this out into a common function to remove the
duplication.
Cc: Jim Lin <jilin@nvidia.com>
Cc: Stefan Agner <stefan@agner.ch>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The TRM for Tegra30 and later all state that USBMODE_CM_HC must be set
before writing to hostpc1_devlc to select which PHY to use for a USB
controller. However, neither init_{utmi,ulpi}_usb_controller() do this
today, so the register writes they perform for PHY selection do not
work.
For the UTMI case, this was hacked around in commit 7e44d9320e "ARM:
Tegra: USB: EHCI: Add support for Tegra30/Tegra114" by adding code to
ehci_hcd_init() which sets USBMODE_CM_HC and duplicates the PHY
selection register write. This code doesn't cover the ULPI case, so I
wouldn't be surprised if ULPI doesn't work with the current code, unless
the ordering requirement only ends up being an issue in HW for UTMI not
ULPI.
This patch fixes init_{utmi,ulpi}_usb_controller() to correctly set
USBMODE_CM_HC before selecting the PHY. Now that this works, we can
remove the duplicate UTMI-specific code in ehci_hcd_init(), thus
simplifying that function.
Cc: Jim Lin <jilin@nvidia.com>
Cc: Stefan Agner <stefan@agner.ch>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Commit 4a271cb1b4 doesn't take into account that fdtdec_setup_gpio()
returns success when the gpio passed to it is FDT_GPIO_NONE (no
gpio node found in the fdtdec_decode_gpio() call). This results in
calling gpio_direction_output() on invalid gpio. For this reason
executing "usb start" command on Arndale causes data abort in the
ehci-exynos driver.
Add the fdt_gpio_isvalid() check to fix that problem.
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Cc: Julius Werner <jwerner@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Marek Vasut <marex@denx.de>
The rmobile SoC has usb host controller.
This supports USB controllers listed in the R8A7790, R8A7791 and R8A7740.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Increase TXFIFOTHRES field value in TXFILLTUNING register of usb for T4 Rev 2.0.
This decreases data burst rate with which data packets are posted from the TX
latency FIFO to compensate for latencies in DDR pipeline during DMA.
This avoids Tx buffer underruns and leads to successful usb writes
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Put a delay of 5 millisecond after reset so that ULPI phy
gets enough time to come out of reset. Erratum A007075 applies
to following SOCs and their variants, if any
P1010 rev 1.0
B4860 rev 1.0, 2.0
P4080 rev 2.0, 3.0
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Set correct phy_type value for second USB controller.
This is required for supporting SOCs having 2 USB controllers
working simultaneously, one with UTMI phy and other with ULPI phy
Signed-off-by: Nikhil Badola <B46172@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Combine the Tegra USB header file into one header file for all SoCs.
Use ifdef to account for the difference, especially Tegra20 is quite
different from newer SoCs. This avoids duplication, mainly for
Tegra30 and newer devices.
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Tom Warren <twarren@nvidia.com>
On Tegra30 and later, the PTS (parallel transceiver select) and STS
(serial transceiver select) are part of the HOSTPC1_DEVLC_0 register
rather than PORTSC1_0 register. Since the reset configuration
usually matches the intended configuration, this error did not show
up on Tegra30 devices.
Also use the slightly different bit fields of first USB, (USBD) on
Tegra20 and move those definitions to the Tegra20 specific header
file.
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Clear the forced powerdown bit in the UTMIP_PLL_CFG2_0 register
which brings USB2 in UTMI mode to work. This was clearly missing
since the forced powerdown bit is set in reset by default for all
USB ports.
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Many USB host controller drivers contain almost identical copies of the
same virtual root hub descriptors. Put these into a common file to avoid
duplication.
Note that there were some very minor differences between the descriptors
in the various files, such as:
- USB 1.0 vs. USB 1.1
- Manufacturer/Device ID
- Max packet size
- String content
I assume these aren't relevant.
Cc: Thomas Lange <thomas@corelatus.se>
Cc: Shinya Kuribayashi <skuribay@pobox.com>
Cc: Gary Jennejohn <garyj@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Eric Millbrandt <emillbrandt@coldhaus.com>
Cc: Pierre Aubert <p.aubert@staubli.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Daniel Hellstrom <daniel@gaisler.com>
Cc: Denis Peter <d.peter@mpl.ch>
Cc: Rodolfo Giometti <giometti@linux.it>
Cc: Zhang Wei <wei.zhang@freescale.com>
Cc: Mateusz Zalega <m.zalega@samsung.com>
Cc: Remy Bohmer <linux@bohmer.net>
Cc: Markus Klotzbuecher <mk@denx.de>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Gary Jennejohn <garyj@denx.de>
Cc: C Nauman <cnauman@diagraph.com>
Cc: David Müller <d.mueller@elsoft.ch>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Thomas Abraham <t-abraham@ti.com>
Cc: Tom Rini <trini@ti.com>
Cc: Andrew Murray <amurray@embedded-bits.co.uk>
Cc: Matej Frančeškin <matej.franceskin@comtrade.com>
Cc: Cliff Cai <cliff.cai@analog.com>
Cc: Bryan Wu <cooloney@gmail.com>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
These data structures are passed to cache-flushing routines, and hence
must be conform to both the USB the cache-flusing alignment requirements.
That means aligning to USB_DMA_MINALIGN. This is important on systems
where cache lines are >32 bytes.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Section 4.10.2 "Advance Queue" of ehci-specification-for-usb.pdf
specifies how an EHCI controller loads a new QTD for processing if the
QH is not already marked as active. It states:
=====
If the field Bytes to Transfer is not zero and the T-bit in the Alternate
Next qTD Pointer is set to zero, then the host controller uses the
Alternate Next qTD Pointer. Otherwise, the host controller uses the Next
qTD Pointer. If Next qTD Pointer’s T-bit is set to a one, then the host
controller exits this state and uses the horizontal pointer to the next
schedule data structure.
=====
Hence, we must ensure that the alternate next QTD pointer's T-bit
(TERMINATE) is set, so the EHCI controller knows to use the next QTD
pointer.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
With this, fixup a trivial build error of get_effective_memsize needing
to be updated in the new board/freescale/p1010rdb/spl.c
Signed-off-by: Tom Rini <trini@ti.com>
Use first four characters for phy_type comparison. Strcmp() should not
be used to check the phy_type string which maybe parsed by hwconfig_subarg().
Hwconfig_subarg() returns part of hwconfig string starting from
phy_type value till the end of the string. Since phy_type could be
either "utmi" or "ulpi", strncmp() should be used so that a comparison
of "utmi;fsl_ddr:bank_intlv=auto" with "utmi" will succeed.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The driver is no longer used, remove it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Michael Schwingen <michael@schwingen.org>
Cc: Tom Rini <trini@ti.com>
Arndale board has AX88760, which is USB 2.0 Hub & USB 2.0 Ethernet Combo
controller, connected to HSIC Phy of USB host controller via USB3503 hub.
This patch uses board specific board_usb_init function to perform reset
sequence for USB3503 hub and enables the relevant config options for
network to work.
Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org>
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
The controller has 3 ports. The port0 is for USB 2.0 Phy, port1 and port2
are for HSIC phys. The usb 2.0 phy is already being setup. This patch
sets up the hsic phys.
Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org>
Fix the register access in EHCI HCD. We need to use address of the register
as an ehci_writel() argument.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
In case the controller is not initialized, we shall not de-initialize it.
As the control structure will not be filled, we will produce a null ptr
dereference if the controller is not inited.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
The detection function of the EHCI PCI controller was really cryptic,
add a beefy comment and clean the portion of the code up a bit. No
change in the logic of the code.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
In commit bb1f327 we removed the UHH reset to fix NFS root (over usb
ethernet) problems with Beagleboard (3530 ES1.0). However, this
seems to cause USB detection problems for Pandaboard, about (3/8).
On further investigation, it seems that doing the UHH reset is not
the cause of the original Beagleboard problem, but in the way the reset
was done.
This patch adds proper UHH RESET mechanism for OMAP3 and OMAP4/5 based
on the UHH_REVISION register. This should fix the Beagleboard NFS
problem as well as the Pandaboard USB detection problem.
Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
CC: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Conflicts:
arch/arm/cpu/arm926ejs/mxs/Makefile
board/compulab/cm_t35/Makefile
board/corscience/tricorder/Makefile
board/ppcag/bg0900/Makefile
drivers/bootcount/Makefile
include/configs/omap4_common.h
include/configs/pdnb3.h
Makefile conflicts are due to additions/removals of
object files on the ARM branch vs KBuild introduction
on the main branch. Resolution consists in adjusting
the list of object files in the main branch version.
This also applies to two files which are not listed
as conflicting but had to be modified:
board/compulab/common/Makefile
board/udoo/Makefile
include/configs/omap4_common.h conflicts are due to
the OMAP4 conversion to ti_armv7_common.h on the ARM
side, and CONFIG_SYS_HZ removal on the main side.
Resolution is to convert as this icludes removal of
CONFIG_SYS_HZ.
include/configs/pdnb3.h is due to a removal on ARM side.
Trivial resolution is to remove the file.
Note: 'git show' will also list two files just because
they are new:
include/configs/am335x_igep0033.h
include/configs/omap3_igep00x0.h
submit_common_msg should report amount of data passed from/to device.
Instead, it always returned size requested by Host.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Get rid of too many ifdeffery in usb ohci driver
Add following two configuration for USB clock selecting
- CONFIG_USB_ATMEL_CLK_SEL_PLLB: using PLLB as usb ohci input clock
- CONFIG_USB_ATMEL_CLK_SEL_UPLL: using UPLL as usb ohci input clock
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Add usb host support for at91sam9n12ek board.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Introduce different macros for storing addresses of multiple
USB controllers. This is required for successful initialization
and usage of multiple USB controllers inside u-boot
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
commit bba679144d
"usb: rename board_usb_init_type to usb_init_type" missed xhci-omap.c
So, fix that patch here, and fix a checkpatch warning.
WARNING: Avoid unnecessary line continuations
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Previously, only host1 was supported using an index of 0.
Now, otg has index 0, host1 is 1, host2 is 2, host3 is 3.
Since OTG requires usbmode to be set after reset, I added
CONFIG_EHCI_HCD_INIT_AFTER_RESET to nitrogen6x.h and
mx6qsabreauto.h.
I also added a weak function board_ehci_power to handle
turning power on/off for otg.
Type is type of device connected (USB stick vs Host.)
Init is type of device desired.
Only power up port if type == init == USB_INIT_HOST.
Only return error if type != init.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Add the support for the dra7xx xhci usb host.
dra7xx does not contain an EHCI controller so the headers
can be removed from the board file.
The xHCI host on dra7xx is connected to a usb2 phy so need to
add support to enable those clocks.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Moving the usb/phy code from xhci-omap to the usb/phy directory
and moving the associated phy code over to the new file.
Newer TI processors adding xHCI support will have different PHY configurations
so therefore abstracting this code away will prevent messing around with the
xhci-omap file itself.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Recent patches declares board_usb_init function prototype for a new
usb architecture.
Turning on the OMAP_XHCI defines cause a redefinition compiler failure.
So update the board_usb_init to the latest prototype.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
This commit unifies board-specific USB initialization implementations
under one symbol (usb_board_init), declaration of which is available in
usb.h.
New API allows selective initialization of USB controllers whenever needed.
Signed-off-by: Mateusz Zalega <m.zalega@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Add the OMAP file for the xHCI Host controller
This code will initilialize the proper components within the
OMAP5 to enable the xHCI host controller.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Some Exynos boards, such as the SMDK5250, control USB port power through
a GPIO pin. For now this had been hardcoded in the exynos5-dt board
file, but not all boards use the same pin, requiring local changes to
support different boards.
This patch moves the GPIO initialization into the USB host controller
drivers which they belong to, and uses the samsung,vbus-gpio parameter
in the device tree to configure it.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Marek Vasut <marex@denx.de>
This adds driver layer for xHCI controller in Samsung's
exynos5 soc. This interacts with xHCI host controller stack.
Signed-off-by: Vikas C Sajjan <vikas.sajjan@samsung.com>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Julius Werner <jwerner@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Marek Vasut <marex@denx.de>
This adds stack layer for eXtensible Host Controller Interface
which facilitates use of USB 3.0 in host mode.
Adapting xHCI host controller driver in linux-kernel
by Sarah Sharp to needs in u-boot.
Initial porting from Linux kernel version 3.4, with following
top commit history of drivers/usb/host/xhci* :
cf84055 xHCI: Cleanup isoc transfer ring when TD length mismatch found
This adds the basic xHCI host controller driver with bare minimum
features:
- Control/Bulk transfer support has been added with required
infrastructure for necessary xHC data structures.
- Stream protocol hasn't been supported yet.
- No support for quirky devices has been added.
Signed-off-by: Vikas C Sajjan <vikas.sajjan@samsung.com>
Signed-off-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Marek Vasut <marex@denx.de>
Macros defining bmRequestType field of USB device request,
given in table 9.2 USB 2.0 spec, are rather generic macros
which can be further used by other Host controller stacks.
So moving them to usb_defs header.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Julius Werner <jwerner@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Marek Vasut <marex@denx.de>
The EHCI controller has some very specific requirements for the USB 2.0
port test modes, which were not closely followed in the initial test
mode commit. It demands that the host controller is completely shut down
(all ports suspended, Run/Stop bit unset) when activating test mode, and
will not work on an already enumerated port.
This patch fixes that by introducing a new ehci_shutdown() function that
closely follows the procedure listed in EHCI 4.14. Also, when we have
such a function anyway, we might as well also use it in
usb_lowlevel_stop() to make the normal host controller shutdown cleaner.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
The 'enable' argument can be better expressed as boolean.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Otavio Salvador <otavio@ossystems.com.br>
Currently we have the following behavior in ehci_hcd_init()
- Read csmr1 register, clear bit 26 and then set bit 26.
However a little bit later we call set_usb_phy_clk() which clears bit 26, so
let's get rid of the unnecessary code.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Fix the linker error for missing ulpi_reset when ulpi is not defined
in the board config.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Acked-by: Marek Vasut <marex@denx.de>
usb_lowlevel_init() allocates a new periodic_list each time it is invoked,
without freeing the original list. Since it is initialized later on in the code,
just reuse the first-allocated list in future invocations of usb_lowlevel_init.
Cc: Marek Vasut <marex@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Fixes NFS root problems with Beagle (3530 ES1.0) when used with
external USB-ethernet adapter and "USB start" command used within
u-boot.
Soft resetting the UHH module causes instability issues on
all OMAPs so we just avoid it.
See OMAP36xx Errata
i571: USB host EHCI may stall when entering smart-standby mode
i660: USBHOST Configured In Smart-Idle Can Lead To a Deadlock
On OMAP4/5, soft-resetting the UHH module can put it into
Smart-Idle mode and lead to a deadlock.
On OMAP3 this doesn't seem to be the case but still instabilities
are observed on beagle (3530 ES1.0) if soft-reset is used.
e.g. NFS root failures with Linux kernel.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Move the struct ehci_ctrl defition from ehci-hcd.c into ehci.h
so it can be re-used by drivers. In particular, the mv_udc driver
can benefit from this move.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Fix a trivial conflict in arch/arm/dts/exynos5250.dtsi about gpio and
serial.
Conflicts:
arch/arm/dts/exynos5250.dtsi
Signed-off-by: Tom Rini <trini@ti.com>
Tegra30 and Tegra114 are compatible except PLL parameters.
Tested on Tegra30 Cardhu, and Tegra114 Dalmore
platforms. All works well.
Signed-off-by: Jim Lin <jilin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Commit 8f62ca6 "usb: ehci: Support interrupt transfers via periodic list"
didn't include any cache management in the new interrupt transfer path.
It also added an extra write to or_asynclistaddr in usb_lowlevel_init(),
without having flushed out the data there.
Add the missing cache management calls, so that the code works again.
This allows the USB keyboard on Tegra's Seaboard/Springbank boards to
work.
Cc: Patrick Georgi <patrick@georgi-clan.de>
Cc: Vincent Palatin <vpalatin@chromium.org>
Cc: Julius Werner <jwerner@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This patch adds support to both Faraday FUSBH200 and FOTG210,
the differences between Faraday EHCI and standard EHCI are
listed bellow:
1. The PORTSC starts at 0x30 instead of 0x44.
2. The CONFIGFLAG(0x40) is not only un-implemented, and
also has its address space removed.
3. Faraday EHCI is a TDI design, but it doesn't
compatible with the general TDI implementation
found at both U-Boot and Linux.
4. The ISOC descriptors differ from standard EHCI in
several ways. But since U-boot doesn't support ISOC,
we don't have to worry about that.
Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
CC: Marek Vasut <marex@denx.de>
There is at least one non-EHCI compliant controller (i.e. Faraday EHCI)
not only leave RESERVED and CONFIGFLAG registers un-implemented
but also has their address spaces removed.
As an result, the PORTSC register of Faraday EHCI always
starts from 0x30 instead of 0x44 in standard EHCI.
So that we'll need a weak-aliased function for abstraction.
Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
CC: Marek Vasut <marex@denx.de>
1. The 'index' of ehci_submit_root() is not always > 0.
e.g.
While it gets invoked from usb_get_descriptor(),
the 'index' is always a '0'. (See ch.9 of USB2.0)
2. The PORTSC register is not always required, and thus it
should only report a port error when necessary.
It would cause a port scan failure if the ehci_submit_root()
always gets terminated by a port error.
Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
CC: Marek Vasut <marex@denx.de>
This commit broke USB2 on link (Chromebook Pixel):
020bbcb usb: hub: Power-cycle on root-hub ports
However the root cause seems to be a missing mask and missing 'break'
in ehci-hcd.c. This patch fixes both.
On link, 'usb start' with a USB keyboard and memory stick inserted now
finds both. The keyboard works as expected. Also ext2ls shows a directory
listing from the memory stick.
Signed-off-by: Simon Glass <sjg@chromium.org>
We can use a common global method for calculating minimum of
3 numbers. Put the same in 'common header' and let 'ehci'
use it.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Tom Rini <trini@ti.com>
This patch adds a new 'usb test' command, that will set a port to a USB
2.0 test mode (see USB 2.0 spec 7.1.20). It supports all five test modes
on both downstream hub ports and ordinary device's upstream ports. In
addition, it supports EHCI root hub ports.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Legacy iomux support is no longer needed now that all boards have been converted
to iomux-v3.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Following the removal of the smdk6400 board, the s3c64xx SoC becomes unused, so
remove associated code. It will still be possible to restore it later from the
Git history if necessary.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Use the ability to have several active EHCI controller on a system
in the PCI EHCI controller implementation.
Signed-off-by: Simon Glass <sjg@chromium.org>
The interrupt endpoint handling code stores the buffer pointer in the QH
padding field. We need to make it the size of a pointer to avoid strict
aliasing issue with the compiler.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Interrupt transfers aren't meant to be used from the async list
(the EHCI spec indicates trouble with low/full-speed intr on async).
Build a periodic list instead, and provide an API to make use of it.
Then, use that API from the existing interrupt transfer API.
This provides support for USB keyboards using EHCI.
Use timeouts to ensure we cannot get stuck in the keyboard scanning
if something wrong happens (USB device unplugged or fatal I/O error)
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Enabling the non-dt path for the driver so that
we don't get any build errors for non-dt configuration.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
With current FDT support driver tries to parse device node
twice in ehci_hcd_init() and ehci_hcd_stop(), which shouldn't
happen ideally.
Making provision to store data in a global structure and thereby
passing its pointer when needed.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
On EHCI controller with 64-bit address space support, we must initialize
properly the high word for the PCI bus master accesses.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Instead of hardcoding the PCI IDs on the USB controller, use the PCI
class to detect them.
Ensure the busmaster bit is properly set in the PCI configuration.
Signed-off-by: Simon Glass <sjg@chromium.org>
The ehci_hcd entry points were just calling into the Tegra USB
functions. Now that they are in the same file we can just move over the
implementation.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This moves the Tegra USB implementation into the drivers/usb/host
directory. Note that this merges the old
/arch/arm/cpu/armv7/tegra20/usb.c file into ehci-tegra.c. No code
changes, just moving stuff around.
v2: While at it also move some defines and the usb.h header file to make
usb driver usable for Tegra30.
NOTE: A lot more work is required to properly init the PHYs and PLL_U on
Tegra30, this is just to make porting easier and it does no harm here.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Rework ehci-mxs so it supports both ports on MX28. It was necessary
to wrap the per-port configuration into struct ehci_mxs_port and pull
out the clock configuration function.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
The ehci-mxs driver included the register definitions directly.
Use imx-regs.h instead since it contains proper handling of the
differences between mx23 and mx28.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Including header for pads is not needed and breaks board
after renaming pin definitions.
Series-to: u-boot
Series-cc: marex@denx.de,fabio.estevam@freescale.com,eric.nelson@boundarydevices.com
Signed-off-by: Stefano Babic <sbabic@denx.de>
Adding fdt support to ehci-exynos in order to parse
register base addresses from the device node.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
By commit c7e3b2b5, this was chanded to support multiple controllers.
But this has missing of parenthesis. This commit fix it.
-----
r8a66597-hcd.c: In function ‘usb_lowlevel_init’:
r8a66597-hcd.c:911:52: error: expected declaration specifiers before ‘)’
token
r8a66597-hcd.c:935:1: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or‘__attribute__’ before ‘{’ token
r8a66597-hcd.c:939:1: error: expected ‘{’ at end of input
-----
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
CC: Lucas Stach <dev@lynxeye.de>
Some variables are initialized with a value defined by macro.
This was changed to use the macro directly. And the variable not to
use deleted it.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Linux usb/ch9.h seems to have all the same information (and more)
as usbdescriptors.h so use the former instead of the later one.
As a consequense of this change USB_SPEED_* values don't correspond
directly to EHCI speed encoding anymore, I've added necessary
recoding in EHCI driver. Also there is no point to put speed into
pipe anymore so it's removed and a bunch of host drivers fixed to
look at usb_device->speed instead.
Old usbdescriptors.h included is not removed as it seems to be
used by old USB device code.
This makes usb.h and usbdevice.h incompatible. Fortunately the
only place that tries to include both are the old MUSB code and
it needs usb.h only for USB_DMA_MINALIGN used in aligned attribute
on musb_regs structure but this attribute seems to be unneeded
(old MUSB code doesn't support any DMA at all).
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
The correct bit for H1_PM is 16, not 8, which is the DP pull-up impedance
selection bit.
This issue has been reported by Eric Bénard <eric@eukrea.com> and fixed by
Christoph Fritz <chf.fritz@googlemail.com> on Linux, from which these #define-s
had been copied.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Marek Vasut <marex@denx.de>
The correct bit for H1_PM is 16, not 8, which is the DP pull-up impedance
selection bit.
This issue has been reported by Michael Burkey <mdburkey@gmail.com> and fixed by
Christoph Fritz <chf.fritz@googlemail.com> on Linux, from which these #define-s
had been copied.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Marek Vasut <marex@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
A custom board_ehci_hcd_init() may be unneeded, so add a weak default
implementation doing nothing.
By the way, use simple __weak from linux/compiler.h for
board_ehci_hcd_postinit() instead of weak alias with full attribute.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Some MXC SoCs like the i.MX35 have hosts located at unusual offsets, so prepare
to the introduction of i.MX35 support by defining the ehci-mxc hosts offsets at
SoC level.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Make EHCI power and overcurrent polarities configurable. If not set, these new
configurartions keep the default register values so that existing board files
do not have to be changed.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
The i.MX53 has MXC_H*_UCTRL_H*_OC_DIS_BIT bits to disable the oc pin.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
The MXC_*_UCTRL_*PM_BIT bits are available only on i.MX51.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
MXC_OTG_UCTRL_OPM_BIT disables (masks) the power/oc pins if set, like
MXC_H1_UCTRL_H1PM_BIT and MXC_H2_UCTRL_H2PM_BIT, not the opposite.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
MXC_OTG_PHYCTRL_OC_DIS_BIT disables the oc pin if set, like MXC_H1_OC_DIS_BIT,
not the opposite.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Clean up ehci-mxc:
- Remove useless #if's.
- Fix identation.
- Issue a #error if used with an unsupported platform.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
when missing USB PHY clock, u-boot will hang during USB
initialization when issuing "usb start". We should check
USBGP[PHY_CLK_VALID] bit to avoid CPU hanging in this case.
Due to controller issue of PHY_CLK_VALID in ULPI mode, we set
USB_EN before checking PHY_CLK_VALID, otherwise PHY_CLK_VALID
doesn't work.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David Müller <d.mueller@elsoft.ch>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: U-Boot DM <u-boot-dm@lists.denx.de>
The i.MX51 has a single USB PHY clock, while the i.MX53 has two. These 3 clocks
have different clock gate control bit-fields.
The existing code was correct only for i.MX53, so this patch fixes the i.MX51
use case.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Jana Rapava <fermata7@gmail.com>
Cc: Wolfgang Grandegger <wg@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Kill off ehci-core.h
It was used to specify some static controller data. To support more than
one controller being active at any time we have to carry the controller
data ourselfes. Change the ehci interface accordingly.
NOTE: OMAP implemented the ehci stuff a bit backwards and should be fixed
to do the same thing as other platforms. But the change for now is at least
compile clean.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Carry an index in the lowlevel usb functions to make specify the
respective usb controller.
Also pass through an controller struct from lowlevel_init to the
creation of the root usb device of this controller.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Reviewed-by: Marek Vasut <marex@denx.de>
usb_hub_descriptor has to be packed as it's used for
communication with the device. Member wHubCharacteristics
violates the natural alignment rules.
Use explicit unaligned access functions for this member.
Fixes ARMv7 traping while using USB.
v2: fix typo found by Thomas Langer
v3: rebased on top of u-boot-usb/master
Signed-off-by: Lucas Stach <dev@lynxeye.de>
* 'master' of git://git.denx.de/u-boot-usb:
MUSB driver: Timeout is never detected as the while loop does not end
usb: fix ulpi_set_vbus prototype
pxa25x: Add UDC registers definitions
USB: Fix strict aliasing in ohci-hcd
usb: Optimize USB storage read/write
ehci: Optimize qTD allocations
usb_stor_BBB_transport: Do not delay when not required
usb_storage: Remove EHCI constraints
usb_storage: Restore non-EHCI support
ehci-hcd: Boost transfer speed
ehci: cosmetic: Define used constants
ehci: Fail for multi-transaction interrupt transfers
arm:trats: Enable g_dnl composite USB gadget with embedded DFU function on TRATS
arm:trats: Support for USB UDC driver at TRATS board.
dfu:cmd: Support for DFU u-boot command
dfu: MMC specific routines for DFU operation
dfu: DFU backend implementation
dfu:usb: DFU USB function (f_dfu) support for g_dnl composite gadget
dfu:usb: Support for g_dnl composite download gadget.
ehci: cosmetic: Define the number of qt_buffers
Signed-off-by: Wolfgang Denk <wd@denx.de>
commit 5f6aa03fda
USB: Fix complaints about strict aliasing in OHCI-HCD
tried to fix this, but gcc4.4 still complains. So, this
patch basically reverts the above and does a simpler fix.
also, the above commit incorrectly changed
/* corresponds to data_buf[4-7] */
datab [1] = 0;
to
/* corresponds to databuf.u8[4-7] */
databuf.u8[1] = 0;
This patch also fixes that.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Relax the qTD transfer alignment constraints in order to need less qTDs for
buffers that are aligned to 512 bytes but not to pages.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Ilya Yanok <ilya.yanok@cogentembedded.com>
Cc: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
This patch takes advantage of the hardware EHCI qTD queuing mechanism to avoid
software and transfer splitting overhead so as to make transfers as fast as
possible.
The only drawback is a call to memalign. However, this is fast compared to the
transfer timings, and the heap size to allocate is small, e.g. 128 kiB in the
worst case for a transfer length of 65535 packets of 512 bytes.
Tested on i.MX25, i.MX35 and i.MX51. In my test conditions, the speed gain was
very significant (several times faster), which is really appreciable when
accessing large files.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Ilya Yanok <ilya.yanok@cogentembedded.com>
Cc: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
Make some light cosmetic code cleanup by the way.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Ilya Yanok <ilya.yanok@cogentembedded.com>
Cc: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
Interrupt transfers requiring several transactions are not supported by
submit_int_msg() because bInterval is ignored. This patch returns a failure code
and prints an error message in this case.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Ilya Yanok <ilya.yanok@cogentembedded.com>
Cc: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
Also enable the ohci port on hawkboard. These additions result in an
increased u-boot size -- adjust the same accordingly in the board's
config.
Move the usb header for da8xx platforms under arch-davinci.
Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com>
As the register accessing mode is the same for all i.MXS SoCs we ought
to use 'mxs' prefix intead of 'mx28'.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Buffer coming from upper layers should be cacheline aligned/padded
to perform safe cache operations. For now we don't do bounce
buffering so getting unaligned buffer is an upper layer error.
We can't check if the buffer is properly padded with current
interface so just assume it is (consider changing with in the
future). The following changes are done:
1. Remove useless length alignment check. We get actual transfer
length not the size of the underlying buffer so it's perfectly
valid for it to be unaligned.
2. Move flush_dcache_range() out of while loop or it will
flush too much.
3. Don't try to fix buffer address before calling invalidate:
if it's unaligned it's an error anyway so let cache subsystem
cry about that.
4. Fix end buffer address to be cacheline aligned assuming upper
layer reserved enough space. This is potentially dangerous
operation so upper layers should be careful about that.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
The USB spec says that 32 bytes is the minimum required alignment.
However on some platforms we have a larger minimum requirement for cache
coherency. In those cases, use that value rather than the USB spec
minimum. We add a cpp check to <usb.h> to define USB_DMA_MINALIGN and
make use of it in ehci-hcd.c and musb_core.h. We cannot use MAX() here
as we are not allowed to have tests inside of align(...).
Signed-off-by: Tom Rini <trini@ti.com>
[marek.vasut]: introduce some crazy macro voodoo
Signed-off-by: Marek Vasut <marex@denx.de>
[ilya.yanok]: moved external buffer fixes to separate patch,
we use {ALLOC,DEFINE}_ALIGN_BUFFER macros with alignment of USB_DMA_MINALIGN
for qh_list, qh and qtd structures to make sure they are proper aligned
for both controller and cache operations.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Move or_asynclistaddr programming to ehci_submit_async()
function to make sure queue head is properly programmed
before every transfer. This solves the problem with changing
qh address.
Also remove unneeded qh_list->qh_link reprogramming at the
end of transfer.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
This has never been completely sufficient and now happens too late to
paper over the cache coherency problems with the current USB stack.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
* 'master' of git://git.denx.de/u-boot-arm:
tegra: define fdt_load/fdt_high variables
tegra: enable bootz command
tegra: usb: Fix device enumeration problem of USB1
tegra: trimslice: set up serial flash pinmux
tegra: add pin_mux_spi() board initialization function
tegra: add GMC/GMD funcmux entry for SFLASH
tegra: bootcmd: start USB only when needed
tegra: bootcmd enhancements
tegra: add enterrcm command
tegra: enable CONFIG_ENV_VARS_UBOOT_CONFIG
Add env vars describing U-Boot target board
tegra: usb: fix wrong error check
tegra: add ULPI on USB2 funcmux entry
tegra: fix leftover CONFIG_TEGRA2_MMC & _SPI build switches
tegra: Add Tamonten Evaluation Carrier support
tegra: Use SD write-protect GPIO on Tamonten
tegra: Implement gpio_early_init() on Tamonten
tegra: Allow boards to perform early GPIO setup
tegra: plutux: Add device tree support
tegra: medcom: Add device tree support
tegra: Rework Tamonten support
beagle: add eeprom expansion board info for bct brettl4
Signed-off-by: Wolfgang Denk <wd@denx.de>
A known hardware issue of USB1 port where bit 1 (connect status
change) of PORTSC register will be set after issuing Port Reset
(like "usb reset" in u-boot command line).
This will be treated as an error and stops later device enumeration.
Therefore we clear that bit after Port Reset in order to proceed
later device enumeration.
Signed-off-by: Jim Lin <jilin@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This patch adds functions to enable/disable the power of USB
host controller for EXYNOS5.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Che-Liang Chiou <clchiou@chromium.org>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Commit 7a101e946cba55e32d3d1265e30456c810046da3 introduced following warning:
---8<---
ehci-atmel.c: In function 'ehci_hcd_init':
ehci-atmel.c:49:2: warning: suggest parentheses around comparison in operand of '&' [-Wparentheses]
ehci-atmel.c: In function 'ehci_hcd_stop':
ehci-atmel.c:79:2: warning: suggest parentheses around comparison in operand of '&' [-Wparentheses]
--->8---
This patch fixes it.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
cc: Bo Shen <voice.shen@atmel.com>
cc: Marek Vasut <marex@denx.de>
Some Atmel SoC support USB EHCI, add the EHCI driver to support it.
To enable the USB EHCI, add the following configuration options into
board relative configuration file and remove USB OHCI options.
#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_ATMEL
#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 2
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
* 'master' of git://git.denx.de/u-boot-usb:
USB: S5P: Add ehci support
usb:udc:samsung Add functions for storing private gadget data in UDC driver
usb:gadget:composite: Support for composite at gadget.h
usb:gadget:composite USB composite gadget support
usb:udc:samsung:cleanup Replace DEBUG_* macros with debug_cond() calls
usb:udc: Remove duplicated USB definitions from include/linux/usb/ch9.h file
USB: Document the QH and qTD antics in EHCI-HCD
USB: Drop cache flush bloat in EHCI-HCD
USB: Drop ehci_alloc/ehci_free in ehci-hcd
USB: Align buffers at cacheline
usb: use noinline define
The construction of QH and qTD lists in ehci_submit_async() call is cryptic
business, add at least a bit of comments so if someone is reading it, he can at
least reference the intel ehci manual (ehci-r10.pdf).
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Discard the creepy cache flushing mechanisms in ehci-hcd.c and replace them with
more straightforward flushing. In the new approach, the flushing takes place
directly in ehci_submit_async() call instead of going through the QH list and
flushing all members and buffers. This discards a lot of weird bit operations
on the members of QH and qTD structures.
NOTE: Certainly, this flushes even qTDs which are possibly unused in some
transactions, though the overhead of the previous code was much higher than is
the overhead of flushing two more cache lines (which most probably aren't even
cached).
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
These two functions were called only from ehci_submit_async(), therefore
dissolve them as part of ehci_submit_async() to get rid of all those static
variables.
Signed-off-by: Marek Vasut <marex@denx.de>
The reference manual of i.MX25 (nor i.MX31) does not define such
register. This seems to access read only UH2_CAPLENGTH register (if
CONFIG_MXC_USB_PORT is zero).
Signed-off-by: Timo Ketola <timo@exertus.fi>
Acked-by: Stefano Babic <sbabic@denx.de>
The USB controller in i.MX25 has a PORTSCx registers which should be
set. In this regard it is similar to the controller in i.MX31. As this
file is compiled only with i.MX25 and -31, #ifdef check can be removed.
Signed-off-by: Timo Ketola <timo@exertus.fi>
Acked-by: Stefano Babic <sbabic@denx.de>
To get USB working again on the i.MX6, this patch fixes a bug introduced
with commit 522b2a0 "Add proper IO accessors for mx6 usb registers.".
At that occasion, I also added the missing __iomem directive.
Cc: Marek Vasut <marex@denx.de>
CC: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Wolfgang Grandegger <wg@denx.de>
This is just a patch for the problem reported here:
http://lists.denx.de/pipermail/u-boot/2012-February/117580.html originally reported by Igor.
"Looks like this is copy paste error from my side,(for port2/3 it should have been bypass
for port2/3 rather its port1 set in bypass mode)"
I only submit the patch since it is missing in 2012.04-rc3 while the twister board
depends on it. Maybe it is already somewhere in the reposistory, but I cannot find it.
note: the twister boards still needs an additional `usb reset`, don't know why.
U-Boot 2012.04-rc3-dirty (Apr 19 2012 - 21:38:38)
AM35XX-GP ES1.0, CPU-OPP2, L3-165MHz, Max CPU Clock 600 Mhz
TAM3517 TWISTER Board + LPDDR/NAND
I2C: ready
DRAM: 256 MiB
NAND: 512 MiB
MMC: OMAP SD/MMC: 0
In: serial
Out: serial
Err: serial
Die ID #746c0000000000000155dc1405011024
Net: DaVinci-EMAC, smc911x-0
Hit any key to stop autoboot: 0
twister => usb start
(Re)start USB...
USB: Register 1313 NbrPorts 3
USB EHCI 1.00
scanning bus for devices... 1 USB Device(s) found
scanning bus for storage devices... 0 Storage Device(s) found
twister => usb reset
(Re)start USB...
USB: Register 1313 NbrPorts 3
USB EHCI 1.00
scanning bus for devices... 1 USB Device(s) found
scanning bus for storage devices... 0 Storage Device(s) found
twister => usb reset
(Re)start USB...
USB: Register 1313 NbrPorts 3
USB EHCI 1.00
scanning bus for devices... 1 USB Device(s) found
scanning bus for storage devices... 0 Storage Device(s) found
twister => usb reset
(Re)start USB...
USB: Register 1313 NbrPorts 3
USB EHCI 1.00
scanning bus for devices... 1 USB Device(s) found
scanning bus for storage devices... 0 Storage Device(s) found
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Acked-by: Govindraj.R <govindraj.raja <at> ti.com>
Acked-by: Tom Rini <trini@ti.com>
This adds basic support for the Tegra2 USB controller. Board files should
call board_usb_init() to set things up.
Configuration is performed through the FDT, with aliases used to set the
order of the ports, like this fragment:
aliases {
/* This defines the order of our USB ports */
usb0 = "/usb@0xc5008000";
usb1 = "/usb@0xc5000000";
};
drivers/usb/host files ONLY: Acked-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
CONFIG_USB_EHCI_TXFIFO_THRESH enables setting of the txfilltuning
field in the EHCI controller on reset.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add proper IO accessors for mx6 usb registers.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Jason Liu <r64343@freescale.com>
This patch renames mx28_register to mx28_register_32 in order to
prepare for the introduction of an 8-bit register, mx28_register_8.
Signed-off-by: Robert Delien <robert@delien.nl>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
Common code has a mdelay() func, so use that instead of the usb-specific
wait_ms() func. This also fixes the build errors:
ohci-hcd.c: In function 'submit_common_msg':
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1519:9: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1816:10: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1827:10: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1844:10: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1563:11: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1583:9: sorry, unimplemented: called from here
make[1]: *** [ohci-hcd.o] Error 1
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Marek Vasut <marex@denx.de>
This moves keyboard polling logic from USB HCD drivers into USB
keyboard driver. Remove usb_event_poll() as keyboard polling was
the only user of this API. With this patch USB keyboard works with
EHCI controllers again. Tested on a tegra2 seaboard.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Clean up added ehci-omap.c and make it generic for re-use across
omap-soc having same ehci ip block. Also pass the modes to be configured
from board file and configure the ports accordingly. All usb layers
are not cache aligned, till then keep cache off for usb ops as ehci will use
internally dma for all usb ops.
* Add a generic common header ehci-omap.h having common ip block
data and reg shifts.
* Rename and modify ehci-omap3 to ehci.h retain only conflicting
sysc reg shifts remove others and move to common header file.
* pass the board data for beagle/panda accordinly to use
ehci ports.
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Fix trailing white space, indentation by spaces instead of TABs,
excessive blank lines, trailing blank lines.
Signed-off-by: Wolfgang Denk <wd@denx.de>
This patch allows USB to work on some hosts, which need additional frobing after
the host was powered up via regular USB powerup sequence.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
Cc: Wolfgang Grandegger <wg@denx.de>
Cc: Jason Liu <r64343@freescale.com>
This is useful for USB Transceivers init etc.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
Cc: Wolfgang Grandegger <wg@denx.de>
Cc: Jason Liu <r64343@freescale.com>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
Cc: Wolfgang Grandegger <wg@denx.de>
Cc: Jason Liu <r64343@freescale.com>
It's derived from ehci-mxc and uses the header files of the
ehci-fsl interface. The callback board_ehci_hcd_init() has
been introduced to allow for board-specific setup when USB
is started.
Signed-off-by: Wolfgang Grandegger <wg@denx.de>
CC: Stefano Babic <sbabic@denx.de>
CC: Remy Bohmer <linux@bohmer.net>
According to EHCI specification v1.0, the controller should stabilize
the power on a port at most 20 ms after the port power bit transition.
So, we put this setting in the virtual descriptor corresponding field,
(bPwrOn2PwrGood = 10 => 10 x 2ms = 20ms), this saves about 500ms at each
controller initialization/enumeration.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Fix:
ehci-mxc.c: In function 'ehci_hcd_init':
ehci-mxc.c:113:6: warning: variable 'tmp' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Fix:
sl811-hcd.c: In function 'sl811_rh_submit_urb':
sl811-hcd.c:556:8: warning: variable 'wIndex' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
* 'master' of git://git.denx.de/u-boot-arm:
arm, davinci: add DAVINCI_MMC_CLKID
arm, davinci_emac: fix driver bug if more then 3 PHYs are detected
arm, davinci: da850/dm365 lowlevel cleanup
omap5: Add omap5_evm board build support.
omap4/5: Add support for booting with CH.
omap5: emif: Add emif/ddr configurations required for omap5 evm
omap5: clocks: Add clocks support for omap5 platform.
omap5: Add minimal support for omap5430.
omap: Checkpatch fixes
omap4: make omap4 code common for future reuse
GCC4.6: Squash warnings in onenand_base.c
GCC4.6: Fix common/usb.c on xscale
OneNAND: Add simple OneNAND SPL
PXA: vpac270: Enable the new generic MMC driver
PXA: Cleanup serial_pxa
PXA: Drop csb226 and innokom boards (unmaintained)
m28evk: Fix comment about the number of RAM banks
mx31: Fix checkpatch warnings in generic.c
mx31: Use proper IO accessor for GPR register
mx31: Remove duplicate definition for GPR register
qong: Use generic function for configuring GPR register
M28EVK: Enable USB HOST support
iMX28: Add USB HOST driver
iMX28: Add USB and USB PHY register definitions
M28: Add memory detection into SPL
iMX28: Fix ARM vector handling
M28: Add doc/README.m28 documentation
M28: Add MMC SPL
iMX28: Add support for DENX M28EVK board
iMX28: Add u-boot.sb target to Makefile
iMX28: Add image header generator tool
iMX28: Add driver for internal RTC
iMX28: Add GPMI NAND driver
iMX28: Add APBH DMA driver
iMX28: Add SPI driver
iMX28: Add GPIO control
iMX28: Add I2C bus driver
iMX28: Add PINMUX control
FEC: Add support for iMX28 quirks
iMX28: Add SSP MMC driver
iMX28: Initial support for iMX28 CPU
MX25: zmx25: GCC4.6 fix build warnings
da850: add new config file for AM18xx
BeagleBoard: config: Switch to ttyO2
OMAP3: Change omap3_evm maintainer
devkit8000: Fix NAND SPL on boards with 256MB NAND
integrator: enable Vpp and disable flash protection
integrator: add system controller header
integrator: make flash writeable on boot
integrator: use io-accessors for board init
integrator: move text offset to config
integrator: pass configs for core modules
ARM: remove superfluous setting of arch_number in board specific code.
SPL: Allow ARM926EJS to avoid compiling in the CPU support code
integrator: do not test first part of the memory
arm: a320: fix broken timer
ARM: define CONFIG_MACH_TYPE for all ronetix boards
dm646x: pass board revision info to kernel
dm646x: add new configuration for dm6467T
arm, davinci: Fix setting of the SDRAM configuration register
arm, davinci: Remove the duplication of LPSC functions
arm, davinci: Rename AM1808 lowlevel functions to DA850
da8xxevm: fix build error
ARM: re-add MACH_TYPE_XXXXXX for VCMA9 board and add CONFIG_MACH_TYPE
Fix:
ehci-fsl.c: In function 'ehci_hcd_init':
ehci-fsl.c:43:7: warning: variable 'usb_phy' set but not used [-Wunused-but-set-variable]
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This driver supports both EHCI ports on the i.MX28 CPU.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
The USB port to be used is determined by CONFIG_MXC_USB_PORT.
So, it appears that the comment is not correct. Remove it.
Signed-off-by: Wolfgang Grandegger <wg@denx.de>
For files like the drivers/serial/serial.c, it must include the
platform file, as the CONFIG_SYS_NS16550_COM1 must reference to the
definition in the platform definition files.
Include the platform definition file in the config file, so that it
would decouple the dependence for the driver files.
Signed-off-by: Lei Wen <leiwen@marvell.com>
There are several mdelay() definitions in the driver and
board code. Remove them all and provide a common mdelay()
in lib/time.c.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Fix:
ohci-hcd.c: In function 'dl_transfer_length':
ohci-hcd.c:968:8: warning: variable 'tdINFO' set but not used [-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
Acked-by: Remy Bohmer <linux@bohmer.net>
Add UTMI and ULPI PHY support for USB controller on qoriq series of
processors with internal UTMI PHY implemented, for example P1010/P1014
- Use both getenv() and hwconfig to get USB phy type till getenv()
is depricated
- Introduce CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY to specify if soc
has internal UTMI phy
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Acked-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
With this, the EHCI seems to "recover" from a timeout. This is particularly
observable if you were to ping the wrong IP Address and then ping the correct
one or if there was a temporary failure during tftp sessions.
All it takes is one timeout to disable it. If you have a noisy network (lot
of traffic), even if the traffic is not for the board, the timeouts don't occur.
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Remove __attribute__ ((packed)) to prevent byte access to soc
registers in some gcc versions.
Having patches to enable ehci for the BeagleBoard lying around for
several months, this one was the show-stopper.
Switched to align(4), rather than remove the attribute, per suggestion
from Alexander.
Credits have to go to Laine Walker-Avina <lwalkera@ieee.org> for
finding the problem.
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Cc: Alexander Holler <holler@ahsoftware.de>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Fail in build, because argument of inl used in r8a66597_read_fifo is wrong.
r8a66597.h:441:35: error: macro "inl" passed 2 arguments, but takes just 1
In file included from r8a66597-hcd.c:25:
r8a66597.h: In function ‘r8a66597_read_fifo’:
r8a66597.h:441: error: ‘inl’ undeclared (first use in this function)
r8a66597.h:441: error: (Each undeclared identifier is reported only once
r8a66597.h:441: error: for each function it appears in.)
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Adding support for USB host on imx25 using the internal PHY. Changing the name
of base address define for imx31 to get some unification.
Signed-off-by: Matthias Weisser <weisserm@arcor.de>
As exception among the i.MX processors, the i.MX31 has headers
without general names (mx31-regs.h, mx31.h instead of imx-regs.h and
clock.h). This requires several nasty #ifdef in the drivers to
include the correct header. The patch cleans up the driver and
renames the header files as for the other i.MX processors.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Add ULI1575 EHCI controller to the list of the supported devices.
Signed-off-by: Zhao Chenhui <b35336@freescale.com>
Acked-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds support for the PI7C9X442SL PCIe EHCI host controller
from Pericom.
Tested at P4080DS eval board from Freescale.
Signed-off-by: Ralf Trübenbach <ralf.truebenbach@men.de>
Cc: Remy Bohmer <linux@bohmer.net>
Changed both to use a common timeout for URB submission, since they were using
different values and EHCI's was too short.
Also fixed EHCI to actually check if urb submission succeeded, rather than
silently continuing into the weeds.
Change-Id: I7f71499ffaa05187d8e5618db2419e1606007b82
Signed-off-by: Simon Glass <sjg@chromium.org>
Calling usb_dev_init() from within the EHCI host driver is wrong.
The EHCI host driver should have no dependency/interconnection to the
USB device driver.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
This patch fixes a problem noticed on lwmon5 (PPC440EPx) using the
common EHCI driver, when "usb reset" is issued multiple times.
Upon the 2nd (and further) "usb reset" command, the command fails
with the following messages:
=> usb reset
(Re)start USB...
USB: Register 1111 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 5 USB Device(s) found
scanning bus for storage devices... 2 Storage Device(s) found
=> usb reset
(Re)start USB...
USB: EHCI fail to reset
Error, couldn't init Lowlevel part
This patch fixes this problem. Now "usb reset" can be called multiple
times.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
This watchdog reset call is needed here, otherwise the lwmon5 board
(PPC440EPx based) will reset upon the "usb reset" command.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
Checking the status field of the qTD token in the current code
do not take into acount cases where endpoint stall (halted) bit
is set together with XactErr status bit. As a result clearing
stall on an endpoint won't be done if this status bit was also
set. Check for halted bit and report USB_ST_STALLED status
if the host controller also indicates endpoit stall condition.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Before this commit, weak symbols were not overridden by non-weak symbols
found in archive libraries when linking with recent versions of
binutils. As stated in the System V ABI, "the link editor does not
extract archive members to resolve undefined weak symbols".
This commit changes all Makefiles to use partial linking (ld -r) instead
of creating library archives, which forces all symbols to participate in
linking, allowing non-weak symbols to override weak symbols as intended.
This approach is also used by Linux, from which the gmake function
cmd_link_o_target (defined in config.mk and used in all Makefiles) is
inspired.
The name of each former library archive is preserved except for
extensions which change from ".a" to ".o". This commit updates
references accordingly where needed, in particular in some linker
scripts.
This commit reveals board configurations that exclude some features but
include source files that depend these disabled features in the build,
resulting in undefined symbols. Known such cases include:
- disabling CMD_NET but not CMD_NFS;
- enabling CONFIG_OF_LIBFDT but not CONFIG_QE.
Signed-off-by: Sebastien Carlier <sebastien.carlier@gmail.com>
This patch solves a problem with USB hanging under higher load on a
i.MX31 board. It falls into class of typical USB problems and fixes:
if you don't understand the real cause, add a delay somewhere.
The problem appeared after introduction of ELF relocation, which
results in smaller code, which appears to run faster (probably because
it fits better in the cache); turning off the instruction cache,
adding debug printf()s and increasing the delay have all been found to
make the problem go away.
Moving the original "udelay(1)" up in the code to it's new place made
the problem appear much less frequently. Increasing the delay to 2
microseconds then made the code run reliably in all (hour-long) tests.
To be on the safe side, we set it to 5 microseconds here.
Signed-off-by: Heiko schocher <hs@denx.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
Cc: Stefano Babic <sbabic@denx.de>
Commit 3ed1607 "USB: sync Queue Element Transfer Descriptor against
EHCI spec" added an "__attribute__ ((aligned (32)))" to the
declaration of struct qTD, as used for example in the Linux kernel as
well.
However, it turns out that this attribute causes errors in "usb start"
(like "ERROR: NOT USB_CONFIG_DESC 7b" and similar). Drop the attribute
again.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Dan Lykowski <lykowdk@gmail.com>
Cc: Remy Bohmer <linux@bohmer.net>
Cc: Stefano Babic <sbabic@denx.de>
It is useful to know the EHCI-PCI hccr, hcor and hc_lenght to make sure it was
successfully registered, and at the correct location.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Appendix B "EHCI 64-Bit Data Structures" of the "Enhanced Host
Controller Interface Specification for Universal Serial Bus" (Rev.
1.0, March 12, 2002) defines additional fields which were missing in
U-Boot's struct qTD; as these are also present in recent versions of
struct ehci_qtd in the Linux kernel, we add them here, too.
This fixes some nasty memory corruption problems.
Reported-by: Dan Lykowski <lykowdk@gmail.com>
See http://permalink.gmane.org/gmane.comp.boot-loaders.u-boot/76942
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
Cc: Dan Lykowski <lykowdk@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Tested-by: Stefano Babic <sbabic@denx.de>
Sometimes a usb tree is not popolated after a system reset.
It seems a delay is required after setting the USB ports
for the MX.31 before resetting the ehci controller.
Signed-off-by: Stefano Babic <sbabic@denx.de>
This fixes TIMEOUT with my Kingston 32GB USB3.0 flashdrive, which I experienced
on my PXA270 (USB 1.1) Vpac270 board.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
This avoids a build warning that you see if anyone in the
header chain has included io.h (which is coming shortly). The previous
code redefined readl/writel; this patch renames it to be specific to
ohci. The defines are also moved from ohci-hcd.c to ohci.h.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Add USB OHCI support for at91sam9g45ekes/at91sam9m10g45ek boards.
Note that according to errata from Atmel, OHCI is not operational
on the first revision of at91sam9g45 chip. So this patch enables
OHCI support for later revisions.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
ehci_submit_async() doesn't really zero out the QH transfer overlay (as the EHCI
specification suggests) which leads to the controller seeing the "token" field
as the previous call has left it, i.e.:
- if a timeout occured on the previous call (Active bit left as 1), controller
incorrectly tries to complete a previous transaction on a newly programmed
endpoint;
- if a halt occured on the previous call (Halted bit set to 1), controller just
ignores the newly programmed TD(s) and the function then keeps returning error
ad infinitum.
This turned out to be caused by the wrong orger of the arguments to the memset()
call in ehci_alloc(), so the allocated TDs weren't cleared either.
While at it, stop needlessly initializing the alternate next TD pointer in the
QH transfer overlay...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Remy Bohmer <linux@bohmer.net>
Add NEC EHCI controller to the list of the supported devices.
Signed-off-by: Sergei Shtylyov <sshtylyov@mvista.com>
drivers/usb/host/ehci-pci.c | 1 +
1 file changed, 1 insertion(+)
Commit b416191a14 (Fix EHCI port reset.) didn't
move the code that checked for successful clearing of the port reset bit from
ehci_submit_root(), relying on wait_ms() call instead. The mentioned code also
erroneously reported port reset state when the reset was already completed.
Signed-off-by: Sergei Shtylyov <sshtylyov@mvista.com>
USB devices on the 2nd port are not detected and I get the following message:
The request port(1) is not configured
That's with default CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS value of 2. 'req->index'
is 1-based, so the comparison in ehci_submit_root() can't be correct.
Signed-off-by: Sergei Shtylyov <sshtylyov@mvista.com>
On little endian machines, EHCI root hub's USB revision is reported as 0.2 --
cpu_to_le16() was missed in the initializer for the 'bcdUSB' descriptor field.
The same should be done for the 'bcdDevice' field.
Signed-off-by: Sergei Shtylyov <sshtylyov@mvista.com>
This patch is part of migrating the AT91 support towards
using C struct for all SOC access.
It removes one more CONFIG_AT91_LEGACY warning.
at91_pmc.h needs cleanup after migration of the drivers
has been done.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
* add's a warning to all files, which need update to new SoC access
* convert common files in cpu/../at91 and a lot of drivers to use
c stucture SoC access
Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de>
In USB ehci driver, the port reset is not terminated. EHCI spec says "A host
controller must terminate the reset and stabilize the state of the port within
2 milliseconds". Without termination, a port stays at reset state. This is
observed on ppc4xx(sequoia) boards.
Signed-off-by: Chris Zhang <chris@seamicro.com>
The header files usb.h and usbdescriptors.h have the same nameed
structure definitions for
usb_config_descriptor
usb_interface_descriptor
usb_endpoint_descriptor
usb_device_descriptor
usb_string_descriptor
These are out right duplicates in usb.h
usb_device_descriptor
usb_string_descriptor
This one has extra unused elements
usb_endpoint_descriptor
unsigned char bRefresh
unsigned char bSynchAddress;
These in usb.h have extra elements at the end of the usb 2.0
specified descriptor and are used.
usb_config_descriptor
usb_interface_descriptor
The change is to consolidate the definition of the descriptors
to usbdescriptors.h. The dublicates in usb.h are removed.
The extra element structure will have their name shorted by
removing the '_descriptor' suffix.
So
usb_config_descriptor -> usb_config
usb_interface_descriptor -> usb_interface
For these, the common descriptor elements are accessed now
by an element 'desc'.
As an example
- if (iface->bInterfaceClass != USB_CLASS_HUB)
+ if (iface->desc.bInterfaceClass != USB_CLASS_HUB)
This has been compile tested on MAKEALL arm, ppc and mips.
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
This patch adds a unified s3c24x0 cpu header file that selects the header
file for the specific s3c24x0 cpu from the SOC and CPU configs defined in
board config file. This removes the current chain of s3c24-type #ifdef's
from the s3c24x0 code.
Signed-off-by: Kevin Morfitt <kevin.morfitt@fearnside-systems.co.uk>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This change is cheked in Linux source and fix found to be in sync.
This patch is tested for USB host interface on Kirkwood based
Sheevaplug platform (ARM little endian board)
Risk: the impact of this patch is not validated on big endian board.
This need to be checked...
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
ehci-hcd.c: In function 'ehci_submit_root':
ehci-hcd.c:719: warning: value computed is not used
ehci-hcd.c:748: warning: value computed is not used
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
This patch fixes the access to the 'ehci' struct elements which should
have been taken care off in 4ef01010aa
Sorry about that.
Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
The following patch reorganizes/reworks the USB support for mpc83xx
as under:-
* Moves the 83xx USB clock init from drivers/usb/host/ehci-fsl.c to
cpu/mpx83xx/cpu_init.c
* Board specific usb_phy_type is read from the environment
* Adds USB EHCI specific structure in include/usb/ehci-fsl.h
* Copyrights revamped in most of the following files
Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
The following patch moves 8xxx-specifc USB #defines from
drivers/usb/host/ehci-fsl.h to include/usb.
Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
To prepare for the 85xx USB support, which requires interface enablement
only once in (specified) order, no different than instructions for
enabling the interface under 83xx. It is unknown why the original author
enabled the interface twice (checked for references in errata, etc).
Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
This patch corrects the missing PLLB initialization in usb_cpu_init()
for AT91SAM9261.
Because of the missing PLLB initialization, the USB support for all
AT91SAM9261 based boards will work only if the PLLB is configured by a
precedent bootloader.
Signed-off-by: Ilko Iliev <iliev@ronetix.at>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
__attribute__ follows gcc's documented syntax and is generally more
common than __attribute. This change is only asthetic and should not
affect functionality.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
move to linux usb driver organisation
as following
drivers/usb/gadget
drivers/usb/host
drivers/usb/musb
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
