There is no real need to include full DT when only some nodes are enough to
use. It will save some space.
Retested with FSBL for initial SoC setup. SPL didn't work.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Users have option to overwrite default device tree
(CONFIG_DEFAULT_DEVICE_TREE) via environment variable DEVICE_TREE.
Feature has been added long time ago by commit 74de8c9a16
("dts/Makefile: Build the user specified dts") for a little bit different
reason.
But this variable can be also used for different purpose like choosing
proper configuration from FIT image in SPL.
And this is the functionality I would like to use on Xilinx Zynq devices
that current u-boot.img can be composed in the same way based on OF_LIST
and different configuration is taken based on platform specific SPL.
SPL requires low level ps7_init_gpl configuration that's why different
boards require different SPL with fixed board_fit_config_name_match().
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Instead of symlink include origin file and just change model description.
Difference is not in DT but in ps7_init configurations which is taken based
on device tree name that's why the same DT can't be used.
Also update model and update comments to match configurations.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Pinctrl is handled via firmare interface that's why move it there without
reg property and new compatible string.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
dtbs_check is showing warning around GIC compatible property as
interrupt-controller@f9010000: compatible: ['arm,gic-400', 'arm,cortex-a15-gic']
is not valid under any of the given schemas
Similar change has been done also by Linux kernel commit 5400cdc1410b
("ARM: dts: sunxi: Fix GIC compatible")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Node name should be <name>@<address> which is not how partitions are
described.
Issue was found by running dtbs_check as:
flash@0: 'partition@qspi-device-tree', 'partition@qspi-fsbl-uboot',
'partition@qspi-linux', 'partition@qspi-rootfs'
do not match any of the regexes: ...
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Sync DP subsystem with the latest state in Xilinx U-Boot repository.
This binding hasn't been approved in mainline Linux but it is much better
than ancient version which this patch removes.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
In kernel 5.4, support has been added for reading MTD devices via
the nvmem API.
For this the mtd devices are registered as read-only NVMEM providers
under sysfs with the same name as the flash partition label property.
So if flash partition label property of multiple flash devices are identical
then the second mtd device fails to get registered as a NVMEM provider.
This patch fixes the issue by having different label property for different
flashes.
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add clock-cells and clock-output-names for sdhci0 and sdhci1.
These are needed for linux sdhci driver from 5.4 version onwards.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reset controller is handled via firmware that's why it should be the part
of firmware node. Origin solution hasn't been removed when above change was
applied by commit b07e97b4ba ("arm64: zynqmp: Use reset header in
zynqmp.dtsi").
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Modify dts files to add 'no-1-8-v' property for all the ZynqMP boards.
User can remove this property to enable the UHS mode. This is to keep
the same speed (HS) modes across all the stages of the Linux Boot. Due
to power cycling limitation of some of the ZynqMP boards, some SD cards
don't get power cycled and are failing in Linux.
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Sync zynqmp fpga manager with mainline.
Signed-off-by: Nava kishore Manne <nava.manne@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
None name address should be aligned with address. DTC 1.5.1 is reporting
issues related to that.
arch/arm/boot/dts/zynq-zc770-xm010.dts:106.10-119.4: Warning
(spi_bus_reg): /amba/spi@e0007000/flash@0: SPI bus unit address format
error, expected "1"
arch/arm/boot/dts/zynq-zc770-xm013.dts:101.19-109.4: Warning
(spi_bus_reg): /amba/spi@e0006000/eeprom@0: SPI bus unit address format
error, expected "2"
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The same change has been done for Zynq by commit 1241c72b6db1
("ARM: dts: zynq: replace gpio-key,wakeup with wakeup-source property")
in mainline Linux kernel.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Most of the legacy "gpio-key,wakeup" boolean property is already
replaced with "wakeup-source". However few occurrences of old property
has popped up again, probably from the remnants in downstream trees.
Replace the legacy properties with the unified "wakeup-source"
property introduced in the Linux kernel commit 700a38b27eef
("Input: gpio_keys - switch to using generic device properties")
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The dtc has new checks for I2C and SPI buses.
Fix the warnings in node names and unit-addresses.
Warning from Linux kernel:
arch/arm/boot/dts/zynq-zc702.dts:187.13-190.6: Warning (i2c_bus_reg): /amba/i2c@e0004000/i2c-mux@74/i2c@7/hwmon@52: I2C bus unit address format error, expected "34"
arch/arm/boot/dts/zynq-zc702.dts:191.13-194.6: Warning (i2c_bus_reg): /amba/i2c@e0004000/i2c-mux@74/i2c@7/hwmon@53: I2C bus unit address format error, expected "35"
arch/arm/boot/dts/zynq-zc702.dts:195.13-198.6: Warning (i2c_bus_reg): /amba/i2c@e0004000/i2c-mux@74/i2c@7/hwmon@54: I2C bus unit address format error, expected "36"
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Multi boot register can be used for using different boot images and design
better boot strategy. Let EL3 SPL or U-Boot to read it and print it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for the Amlogic based libretech-pc platform.
This platform comes with 2 variant, based on the s905d or s912 SoC.
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
[narmstrong: update board/amlogic/q200/MAINTAINERS]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Sync the libretech-pc device tree from Linux v5.6-rc2
11a48a5a18c6 ("Linux 5.6-rc2")
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Sync the device tree and dt-bindings from Linux v5.6-rc2
11a48a5a18c6 ("Linux 5.6-rc2")
The only exception to this is the mmc pinctrl pin bias of gxl SoC family.
This is a fix which found its way to u-boot but not Linux yet.
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The card-detect GPIO and any other GPIO access currently doesn't work in
U-Boot SPL on any STM32 platform and crashes the SPL. To work around this
problem on AV96 right before release, remove the cd-gpios from DT. This
patch must be reverted right after release, once the proper fix for the
GPIO driver, "gpio: stm32: support gpio ops in SPL", is applied.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Tom Rini <trini@konsulko.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
USB 3 host controller may be described in ACPI to allow users alter
the properties or other features. Describe it for Intel Tangier SoC.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
There is established way to provide I²C timings, or actually counters,
to the OS via ACPI. Fill them for Intel Merrifield platform.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
There is no need to have an assignment to NULL for XSDT pointer.
Therefore, no need to assign it when rsdt_address is not set.
Because of above changes we may decrease indentation level as well.
While here, drop unnecessary parentheses.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Commit f4dc714aaa ("arm64: Turn u-boot.bin back into an ELF file after
relocate-rela")
introduce REMAKE_ELF option to recreate u-boot.elf from u-boot ->
u-boot.bin + DT -> u-boot.elf.
The best is to ilustrate it from make V=1 output
cat u-boot-nodtb.bin dts/dt.dtb > u-boot-dtb.bin
cp u-boot-dtb.bin u-boot.bin
aarch64-linux-gnu-objcopy -I binary -B aarch64 -O elf64-littleaarch64 u-boot.bin u-boot-elf.o
aarch64-linux-gnu-ld.bfd u-boot-elf.o -o u-boot.elf --defsym="_start"=0x8000000 -Ttext=0x8000000
Last command has no explicit linker script passed that's why toolchain
internal linker script is used.
In Binutils 2.32 case it contains SIZEOF_HEADERS symbol which has changed
behavior by commit
https://sourceware.org/git/?p=binutils-gdb.git;a=commit;h=64029e93683a266c38d19789e780f3748bd6a188
which result in situation that program headers has changed from
(xilinx_zynqmp_mini_defconfig)
Program Headers:
Type Offset VirtAddr PhysAddr
FileSiz MemSiz Flags Align
LOAD 0x0000000000010000 0x00000000fffc0000 0x00000000fffc0000
0x0000000000018918 0x0000000000018918 RW 0x10000
to
Program Headers:
Type Offset VirtAddr PhysAddr
FileSiz MemSiz Flags Align
LOAD 0x0000000000000000 0x00000000fffb0000 0x00000000fffb0000
0x0000000000028918 0x0000000000028918 RW 0x10000
Xilinx tools like XSDB or Bootgen are using program headers for loading ELF
to the right location and by above binutils change ELF is loaded to
incorrect location.
The patch is explicitly use u-boot-elf.lds (just cat now) for u-boot.elf
recreation which is called when REMAKE_ELF is setup.
By purpose u-boot-elf.lds doesn't contain OUTPUT_FORMAT/OUTPUT_ARCH to be
able to use by all archs.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Tested-By: Álvaro Fernández Rojas <noltari@gmail.com>
When generating the MAC address based on the boards serial number
the last digit was overwritten with the null termination. That way
boards with serial numbers close to each other would use the same
MAC address.
Signed-off-by: Jan-Christoph Tebbe <Jan-Christoph.Tebbe@ithinx.io>
The Jetson Nano Developer Kit is a Tegra X1-based development board. It
is similar to Jetson TX1 but it is not pin compatible. It features 4GB
of LPDDR4, a SPI NOR flash for early boot firmware and an SD card slot
used for storage.
HDMI 2.0 or DP 1.2 are available for display, four USB ports (3 USB 2.0
and 1 USB 3.0) can be used to attach a variety of peripherals and a PCI
Ethernet controller provides onboard network connectivity. NVMe support
has also been added. Env save is at the end of QSPI (4MB-8K).
A 40-pin header on the board can be used to extend the capabilities and
exposed interfaces of the Jetson Nano.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
According to the HW team, for some reason the normal clock select code
picks what appears to be a perfectly valid 375KHz SD card clock, based
on the CAR clock source and SDMMC1 controller register settings (CAR =
408MHz PLLP0 divided by 68 for 6MHz, then a SD Clock Control register
divisor of 16 = 375KHz). But the resulting SD card clock, as measured by
the HW team, is 700KHz, which is out-of-spec. So the WAR is to use the
values given in the TRM PLLP table to generate a 400KHz SD-clock (CAR
clock of 24.7MHz, SD Clock Control divisor of 62) only for SDMMC1 on
T210 when the requested clock is <= 400KHz. Note that as far as I can
tell, the other requests for clocks in the Tegra MMC driver result in
valid SD clocks.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
As per the T210 TRM, when running at 3.3v, the SDMMC1 tap/trim and
autocal values need to be set to condition the signals correctly before
talking to the SD-card. This is the same as what's being done in CBoot,
but it gets reset when the SDMMC1 HW is soft-reset during SD driver
init, so needs to be repeated here. Also set autocal and tap/trim for
SDMMC3, although no T210 boards use it for SD-card at this time.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Fix VI_I2C clock source type. Will be needed by VI_I2C driver.
Also added use of INTERNAL_ID macro in two places, needed to keep
the id returned to 8 bits.
Signed-off-by: Tom Warren <twarren@nvidia.com>
T210 CBoot is now doing the full pinmux and GPIO init, based on the DTB
tables. Remove pinmux/GPIO init tables & code from all T210-based builds
below:
p2371-2180 aka TX1
p2371-0000
e2220-1170
p2571
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
This commit removes the programming sequence that enables PLLE and UPHY
PLL hardware power sequencers. Per TRM, boot software should enable PLLE
and UPHY PLLs in software controlled power-on state and should power
down PLL before jumping into kernel or the next stage boot software.
Adds call to board_cleanup_before_linux to facilitate this.
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
This adds to the DT the I2C controllers that connect to the board ID EEPROM,
etc. With this change, you can now probe all I2C devices on a TX1 board.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Enable pre console buffer for rk3399 platform.
This would help to capture the console messages prior to
the console being initialised. Enabling this would help
to capture all the console messages on video output source
like HDMI. So we can find the full console messages of
U-Boot proper on HDMI display when enabled it for RK3399
platform boards.
Buffer address used for pre console is 0x0f200000 which is
ram base plus 240MiB. right now the Allwinner SoC is using
similar computation.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
VOP display endpoint pipeline configuration differs
between rk3288 vs rk3399.
These VOP pipeline configuration depends on how the
different display interfaces connected in sequence to
IN and OUT ports like for,
RK3288:
vopb_out: port {
#address-cells = <1>;
#size-cells = <0>;
vopb_out_edp: endpoint@0 {
reg = <0>;
remote-endpoint = <&edp_in_vopb>;
};
vopb_out_hdmi: endpoint@1 {
reg = <1>;
remote-endpoint = <&hdmi_in_vopb>;
};
vopb_out_lvds: endpoint@2 {
reg = <2>;
remote-endpoint = <&lvds_in_vopb>;
};
vopb_out_mipi: endpoint@3 {
reg = <3>;
remote-endpoint = <&mipi_in_vopb>;
};
};
RK3399:
vopb_out: port {
#address-cells = <1>;
#size-cells = <0>;
vopb_out_edp: endpoint@0 {
reg = <0>;
remote-endpoint = <&edp_in_vopb>;
};
vopb_out_mipi: endpoint@1 {
reg = <1>;
remote-endpoint = <&mipi_in_vopb>;
};
vopb_out_hdmi: endpoint@2 {
reg = <2>;
remote-endpoint = <&hdmi_in_vopb>;
};
vopb_out_mipi1: endpoint@3 {
reg = <3>;
remote-endpoint = <&mipi1_in_vopb>;
};
vopb_out_dp: endpoint@4 {
reg = <4>;
remote-endpoint = <&dp_in_vopb>;
};
};
here, HDMI interface has endpoint 1 in rk3288 and 2 in rk3399.
The rockchip vop driver often depends on this determined endpoint
number and stored in vop_mode. So based on this vop_mode the bpp
and pin polarity would configure on detected display interface.
Since, the existing driver using rk3288 vop mode settings enabling
the same will result wrong display interface configuration for rk3399.
Add the patch for fixing these vop modes for rk3399.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
compatibility with stm32mp15_dhcom_basic_defconfig
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl6EiK0ACgkQ4rK92eCq
k3V6DggAhU7jE5MGs9A7En+YpANXbJ4tl56IZIjdzPzEjA2G3yuBv/DLci/w27aF
eaP83ayI/ZrVtevEBFomP0JRrzQc9r/ot+USVugGsoAigLbzJc5uba42FGn09Olh
uKkst0Fb7uPRzZQNwRc7hTKVSLvT11c0oPQyhhJM2djPDTETDry+RPnEFQ41SEUt
bNILmj0VRzikzbe5RXFWWYMUWBrt22pG2LLhog+WSRSpqrWM2zES64NnwAXxD/mR
YIQFZIZ6eWW2Otp+qzenkg5ZWIMVWRyUBAP5e0auKRE8TGWAXgBcoFRTRLf7oA/P
yr3TTBMWiPdqdXNe3MYzAiTpm7jrtg==
=RALH
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20200401' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- Fix device tree of Avenger96 board from Arrow Electronics and add
compatibility with stm32mp15_dhcom_basic_defconfig
The core and vdd PMIC buck regulators were misconfigured, which caused
instability of the board and malfunction of high-speed interfaces, like
the RGMII. Configure the PMIC correctly to repair these problems. Also,
model the missing Enpirion EP53A8LQI on the DHCOR SoM as a fixed regulator.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
The AV96 RGMII uses different pinmux for ETH_RGMII_TXD0, ETH_RGMII_RXD2
and ETH_RGMII_TX_CTL. Use the correct pinmux to make ethernet operational.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Add another mux option for DWMAC RGMII, this is used on AV96 board.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
The board has an EEPROM on the same I2C bus as PMIC, at address 0x53.
The EEPROM contains the board MAC address.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Change-Id: I340a0675c11e4599968b2e3ef0515fb8da8d7b42
Use DT /aliases node to establish a stable phandle to the configuration
EEPROM. This permits the configuration EEPROM to be moved e.g. to a
different address or a different bus. Adjust the board code to handle
new phandle lookup.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
The DH Electronics DHCOR SOM has QSPI NOR on the SoM itself, add it
into the DT.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Change-Id: Ia7c454c496f50e3fc4851ec1154f3641c416e98e
The eMMC uses different pinmux for the top four data lines, use such
a pinmux, otherwise it takes a very long time until the test for 8bit
operation times out. And this is the correct pinmux per schematic too.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Add another mux option for SDMMC2 pins 4..7, this is used on AV96 board.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
The SD uses different pinmux for the D123DIRline, use such a pinmux,
otherwise there is a pinmux collision on the AV96. Add missing SD
voltage regulator switch and enable SDR104 operation.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Add another mux option for SDMMC1 direction pins, in particular
SDMMC1_D123DIR, this is used on AV96 board.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
The sdmmc1_dir_pins_a: sdmmc1-dir-0 layout changed in commit 35a54d41d9
("ARM: dts: stm32mp1: sync device tree with v5.2-rc4") such that pins{};
became pins1{};pins2{};, however the SPL extras were not updated to reflect
that change. Fix this.
This fixes booting from SD1 X9 slot on the AV96 board.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Fixes: 35a54d41d9 ("ARM: dts: stm32mp1: sync device tree with v5.2-rc4")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
This last minute pull-request is intended to fix some drivers
when used on ARC boards. The problem was introduced by
07906b3dad
What happened while doing one pretty simple improvement to make
U-Boot port more flexible and portable (by switching accessors from
assembly-written to plain C version) we implicitly added 2 problems:
1. Downgraded accessors from being volatile which signalled to
the compiler that it's now possible to do all kinds of optimizations
which may easily include merge of subsequent byte reads/writes into
word operations. Which is OK for accessing mormal memory but
breaks operation of peripherals if we access its memory-mapped regs
in such a "creative" manner.
2. As a part of assembly-written implementation we had compiler barriers
in form of the following construction 'asm volatile("" : : : "memory")',
and we dropped it in C implemntation. This in its turn enabled compiler
to mess with instruction ordering. Guess what it gives us in the end :)
So with all that we had in some corner-cases veeery funny instruction flows
generated. And in particular it broke DW SPI functionality when we were
writing large amount of data. Funny enough our tests which were writing
small amount of data still worked and only by the chance we caught that
breakage and unrolled that quite interesting loop of unexpected
problems.
The road to hell is paved with good intentions. Amen :)
We add memory barriers for __raw_readX / __raw_writeX accessors same
way as it is done for readX and writeX accessors as lots of U-boot
driver uses __raw_readX / __raw_writeX instead of proper accessor
with barrier.
It will save us from lot's of debugging in the future and it is OK
as U-Boot is not that performance oriented as real run-time
software like OS or user bare-metal app so we may afford being not
super fast as we only being executed once.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
We must use compiler barriers in C-version read/write IO accessors
before and after operation (read or write) so it won't be reordered
by compiler.
Fixes commit 07906b3dad ("ARC: Switch to generic accessors")
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
We must use 'volatile' in C-version read/write IO accessors
implementation to avoid merging several reads (writes) into
one read (write), or optimizing them out by compiler.
Fixes commit 07906b3dad ("ARC: Switch to generic accessors")
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Add save_boot_params() to save reset status value from bootrom.
Bootrom will clear the status register in reset manager and stores the
reset status value in shared memory. Bootrom stores shared data at last
2KB of onchip RAM.
This function save reset status provided by bootrom to rst_mgr_status.
More information about reset status register value can be found in reset
manager register description.
When running in debugger without bootrom, r0 to r3 are random values.
So, skip save the value when r0 is not bootrom shared data address.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Configure RX and TX bus-width values to use flexspi in octal I/O mode.
If bus-widths are not specified, then single I/O mode is set by default.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Configure RX and TX bus-width values to use flexspi in octal I/O mode.
If bus-widths are not specified, then single I/O mode is set by default.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
lx2160a-qds has 2 micron "mt35xu512aba" flashes of size 64M each
connected on A0 and B1 i.e on CS0 and CS3. Since flashes are connected
on different buses, only one flash can be probed at a time.
Add fspi node properties aligned with LX2160A-RDB fspi properties.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This supports i2c DM and enables CONFIG_DM_I2C
for SoC LS1046A
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
This supports i2c DM and enables CONFIG_DM_I2C
for SoC LS1043A
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Select BOARD_LATE_INIT config so that many board works can be done
in late init stage.
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add IIC3 node from mainline Linux DT. This will be further updated in
subsequent DT sync, however adding this node for now is sufficient and
minimal change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Since commit 79030a4861 ("rockchip: Add Single boot image
(with binman, pad_cat)") the following boot regression is seen:
U-Boot 2020.04-rc3-00050-gd16e18ca6c-dirty (Mar 09 2020 - 11:40:07 -0300)
Model: Elgin RV1108 R1 board
DRAM: 128 MiB
initcall sequence 67fd12a0 failed at call 6000b927 (err=-22)
This happens because the above commit missed to include the
"rockchip-u-boot.dtsi" for rv1108, so include this file
like it done for other Rockchip SoC dtsi's.
Fixes: 79030a4861 ("rockchip: Add Single boot image (with binman, pad_cat)")
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In order to make the console pins more robust to noise, activate
the pullups and increase its drive strength.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This parameter "st,phy-cal" becomes optional and when it is
absent the built-in PHY calibration is done.
It is the case in the helper dtsi file "stm32mp15-ddr.dtsi"
except if DDR_PHY_CAL_SKIP is defined.
This patch also impact the ddr interactive mode
- the registers of the param 'phy.cal' are initialized to 0 when
"st,phy-cal" is not present in device tree (default behavior when
DDR_PHY_CAL_SKIP is not activated)
- the info 'cal' field can be use to change the calibration behavior
- cal=1 => use param phy.cal to initialize the PHY, built-in training
is skipped
- cal=0 => param phy.cal is absent, built-in training is used (default)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Need to increase the LPDDR2/LPDDR3 the voltage vdd2_ddr: buck2
form 1.2V to 1.25V for 32bits configuration.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
This commit manages diversity for STM32M15x SOCs with:
- dedicated files to support all STM32MP15 SOCs family.
The differences between those SOCs are:
-STM32MP151 [1]: common file.
-STM32MP153 [2]: STM32MP151 + CANs + a second CortexA7-CPU.
-STM32MP157 [3]: STM32MP153 + DSI + GPU.
- new files to manage security diversity on STM32MP15x SOCs.
On STM32MP15xY, "Y" gives information:
-Y = A means no cryp IP and no secure boot.
-Y = C means cryp IP + secure boot.
- stm32mp157 pinctrl files to better manage package diversity.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
This path allows to set the cntfrq register of targeted cpu.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Reviewed-by: Patrick DELAUNAY <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
The STM32MP1 series is available in 3 different lines which are pin-to-pin
compatible:
- STM32MP157: Dual Cortex-A7 cores, Cortex-M4 core @ 209 MHz,
3D GPU, DSI display interface and CAN FD
- STM32MP153: Dual Cortex-A7 cores, Cortex-M4 core @ 209 MHz
and CAN FD
- STM32MP151: Single Cortex-A7 core, Cortex-M4 core @ 209 MHz
Each line comes with a security option (cryptography & secure boot)
& a Cortex-A frequency option :
- A : Cortex-A7 @ 650 MHz
- C : Secure Boot + HW Crypto + Cortex-A7 @ 650 MHz
- D : Cortex-A7 @ 800 MHz
- F : Secure Boot + HW Crypto + Cortex-A7 @ 800 MHz
This patch adds the support of STM32MP15xD and STM32MP15xF in U-Boot.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Update the kernel device tree for STM32MP15x product lines according
the used soc and its part number, when CONFIG_OF_SYSTEM_SETUP is activated:
- STM32MP15XA hasn't Crypto (cryp1/2)
- STM32M151 and STM32M153 hasn't 3D GPU and DSI host
- STM32M151 hasn't CAN FD and has single A7
For example:
FDT: cpu 1 node remove for STM32MP151AAA Rev.B
FDT: can@4400e000 node disabled for STM32MP151AAA Rev.B
FDT: gpu@59000000 node disabled for STM32MP151AAA Rev.B
FDT: dsi@5a000000 node disabled for STM32MP151AAA Rev.B
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Add a function get_soc_name to get a string with the full name
of the SOC "STM32MP15xxx Rev.x"
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Add the SMC code and operation for trace on errors.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Add BSEC lock access (read / write) at 0xC0000000 offset of misc driver.
The write access only available for Trusted boot mode, based on new
SMC STM32_SMC_WRLOCK_OTP.
With the fuse command, the permanent lock status is accessed with
0x10000000 offset (0xC0000000 - 0x8000000 for OTP sense/program
divided by u32 size), for example:
Read lock status of fuse 57 (0x39)
STM32MP> fuse sense 0 0x10000039 1
Sensing bank 0:
Word 0x10000039: 00000000
Set permanent lock of fuse 57 (0x39)
STM32MP> fuse prog 0 0x10000039 1
Sensing bank 0:
Word 0x10000039: 00000000
WARNING: the OTP lock is updated only after reboot
WARING: Programming lock or fuses is an irreversible operation!
This may brick your system.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Remove the test offs < 0 , as offs is unsigned.
This patch solves the warnings when compiling with W=1
on stm32mp1 board:
In function ‘stm32mp_bsec_read’:
arch/arm/mach-stm32mp/bsec.c:368:11: warning:
comparison of unsigned expression < 0 is always false [-Wtype-limits]
368 | if (offs < 0 || (offs % 4) || (size % 4))
| ^
In function ‘stm32mp_bsec_write’:
arch/arm/mach-stm32mp/bsec.c:405:11: warning:
comparison of unsigned expression < 0 is always false [-Wtype-limits]
405 | if (offs < 0 || (offs % 4) || (size % 4))
| ^
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Some config symbols are found in *almost* every _defconfig file for
Allwinner boards, because those options are actually a platform choice,
and not a per-board decision.
Some of these options are older, some have recently been added.
Move those options to be set for all Allwinner boards in their
respective Kconfig files.
The rationales are as follows:
- NR_DRAM_BANKS: All Allwinner SoC map DRAM at one contiguous region of
address space only, starting at 1 GB. So it's always one bank.
- SPL_{DOS,EFI}_PARTITION: The Allwinner SPL does only support raw MMC
accesses, we don't care about filesystems or partitions in there, so
there is no need to define those symbols at all.
- USE_PREBOOT: We start USB early when a keyboard is configured, using the
preboot env variable, so we need to set this variable.
- SYS_RELOC_GD_ENV_ADDR: We don't specify any ENV_ADDR, so need this
symbol to be set (according to 8d8ee47e03).
- SYS_USB_EVENT_POLL_VIA_INT_QUEUE: According to commit eab9433aa5,
specifying this reduces the latency of the USB keyboard handling, so
this was formerly enabled in config headers for all Allwinner boards.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # Amarula A64-Relic
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The Allwinner H6 SoC uses a quite different memory map, also changes the
clocks quite a bit. This requires some changes to the SPL SPI routine,
which hardcodes these values so far.
Using the just introduced helper functions to determine base address
and SPI controller generation, we can cover some of these differences
easily.
The clock setup is different, so requires some explicit code changes
there (reset and clock gate in one register at a different address).
Also we need to change the pinmux function to use a different set of
pins that the H6 uses for SPI0.
Eventually we can enable the H6 to use SPI booting in Kconfig.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Now that we can easily select an SoC specific SPI0 base address, adding
support for the Allwinner R40 is fairly trivial:
We set the base address, add this SoC to the ones that use PC23 and
enable it in Kconfig.
This allows booting from SPI flash on R40 boards.
Tested on a Bananapi M2 Berry with SPI flash connected to the header pins.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
So far we were using the CONFIG_SUNXI_GEN_SUN6I symbol to select between
the two SPI controller generations used on Allwinner SoCs. This is a
convenience symbol to roughly differentiate between "older" and "newer"
generation of SoCs.
The H6 SoCs is the newest SoC so far, but is sufficiently different to
not define this symbol. However it is using a SPI controller compatible
to the "new gen" SoCs.
To prepare for H6 support, we replace the check for this single symbol
with an explicit function, which can later be extended.
For now we just return CONFIG_SUNXI_GEN_SUN6I in there, so this does not
create a functional change.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
So far on all supported Allwinner SoCs we find the old generation SPI
controller always at address 0x1c05000, and the new generation one at
0x1c68000. However the Allwinner R40 SoC has a new generation SPI at
the old address, and the H6 uses a completely different address.
So split off the base address from the respective SPI registers, by
changing the #defines to just contain offsets.
The base address is provided by a function, so it can easily be extended
later when support for those SoCs materialises.
This does not change the code size (since the toolchain is clever enough
to optimise this properly), also does not bring any functional change at
this point.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Using memcpy() for some MMIO access is generally frowned upon and might
break things on some platforms. Allwinner H3, which fails to boot, being
an example here.
Moreover, fields being accessed are naturally aligned and warnings
produced by GCC have been quiesced for some time already by:
53dc8ae ("gcc-9: silence 'address-of-packed-member' warning")
That said, it should be okay to revert this commit.
This reverts commit 9bd34a69a4.
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Tomasz Duszynski <tduszyns@gmail.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
K3 J721E:
* OSPI boot support
* Support for loading remote cores in R5 SPL
* PMIC ESM Support
* Minor fixes for R5F and C7x remoteproc drivers
K3 AM654:
* Update AVS class 0 voltages.
* Add I2C nodes
DRA7xx/AM57xx:
* Fixed Android boot on AM57xx
AM33/AM43/Davinci:
* switch to driver model for the net and mdio driver for baltos
* Add DM/DTS support for omap video driver
* Enable fastboot on am335x-evm
Few v0.1 SBI calls are being replaced by new SBI calls that follows
v0.2 calling convention.
Implement the replacement extensions and few additional new SBI
function calls that makes way for a better SBI interface in future.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
We now have SBI v0.2 which is more scalable and extendable to handle
future needs for RISC-V supervisor interfaces.
Introduce a new config and move all SBI v0.1 code under that config.
This allows to implement the new replacement SBI extensions cleanly
and remove v0.1 extensions easily in future. Currently, the config
is enabled by default. Once all M-mode software, with v0.1, is no
longer in use, this config option and all relevant code can be easily
removed.
This commit is inspired from Linux kernel patch:
https://patchwork.kernel.org/patch/11407361/
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Few v0.1 SBI calls are being replaced by new SBI calls that follows
v0.2 calling convention.
This patch just defines these new extensions.
This commit is inspired from Linux kernel patch:
https://patchwork.kernel.org/patch/11407359/
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
The SBI v0.2 introduces a base extension which is backward compatible
with v0.1. Implement all helper functions and minimum required SBI
calls from v0.2 for now. All other base extension function will be
added later as per need.
As v0.2 calling convention is backward compatible with v0.1, remove
the v0.1 helper functions and just use v0.2 calling convention.
Add a new Kconfig options CONFIG_SBI for the new SBI v0.2 codes, and
let CONFIG_SBI_IPI depend on it.
This commit is inspired from Linux kernel patch:
https://patchwork.kernel.org/patch/11407363/
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
As per the new SBI specification, current SBI implementation version
is defined as 0.1 and will be removed/replaced in future. Each of the
function call in 0.1 is defined as a separate extension which makes
easier to replace them one at a time.
Rename existing implementation to reflect that. This patch is just
a preparatory patch for SBI v0.2 and doesn't introduce any functional
changes.
This commit is inspired from Linux kernel patch:
https://patchwork.kernel.org/patch/11407355/
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
There is no need for S-mode U-Boot to call sbi_clear_ipi() as it
can be cleared directly from S-mode. This saves some cycles.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas@auer.io>
Currently sbi_remote_sfence_vma{,_asid} does not pass their arguments
to SBI at all, which is semantically incorrect.
This keeps in sync with Linux kernel commit:
a21344dfc6ad: fix sbi_remote_sfence_vma{,_asid}
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas@auer.io>
As there is only one linker script to use in this case, rather than use
the BOARDDIR variable hard-code the path.
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Suggested-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Masahiro Yamada <masahiroy@kernel.org>
As there is only one machine under mach-orion5x, having a Kconfig entry
for SPL_LDSCRIPT is not helpful, move this to the defconfig file.
Suggested-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Masahiro Yamada <masahiroy@kernel.org>
In a few places we have Kconfig entries that set SPL_LDSCRIPT to what is
the default value anyways. Drop these.
Cc: Michal Simek <monstr@monstr.eu>
Cc: Rick Chen <rick@andestech.com>
Cc: Philippe Reynes <tremyfr@yahoo.fr>
Cc: Eric Jarrige <eric.jarrige@armadeus.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com> (for Microblaze)
Reviewed-by: Masahiro Yamada <masahiroy@kernel.org>
The A72 U-Boot code supports early load and boot of a number of
remote processors including the C66_0 and C66_1 DSPs. The current
code supports only loading into the DDR regions which were already
given the appropriate memory attributes. The C66 DSPs also have L1
and L2 internal memory regions that can behave as normal-memories.
Add a new entry to the J721E MMU table covering these regions with
the appropriate memory attributes to allow the A72 U-Boot code to
support loading directly into these memory regions.
Signed-off-by: Suman Anna <s-anna@ti.com>
Add a separate function for printing sysfw version so that it can be
called independently of k3_sysfw_loader.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The binman-option BINMAN_FDT is introduced by this commit:
commit 3c10dc95bd ("binman: Add a library to access binman entries")
BINMAN_FDT being selected when BINMAN=y that resulting in mt7623
and mt7622 are unable to boot. The root cause of this issue is commit:
commit cbd2fba1ec ("arm: MediaTek: add basic support for MT7629 boards")
select BINMAN=y in all mediatek SoCs, and others mediatek SoCs not
expect to use BINMAN_FDT.
This patch remove BINMAN=y option when ARCH_MEDIATEK=y and
move this to the specify SoCs part config.
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Correct the dependency for STM32 ETZPC protection, linked to SOC
STM32MP identified by CONFIG_STM32MP15x and not linked to
CONFIG_TARGET_STM32MP1 (no more existing).
This patch fix an issue introduced by commit 846254888e ("stm32mp1:
split board and SOC support for STM32MP15x family").
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Instead of resetting the ethernet phy through functions in imx8mq_evk.c, let the
driver reset the phy via dts description adding a reset duration of 10 ms
following atheros 8031's datasheet recommendation.
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
The FEC in the i.MX8MM doesn't support this feature. So don't pretend one
can use it.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Let pinctrl configuration for eMMC node (usdhc1) also be
accessible in SPL.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
The current implementation in arch/arm/mach-imx/cpu.c uses non-DM
code to retrieve the core clock frequency. As the root clock is not
listed we currently get:
CPU: Freescale i.MX8MMQ rev1.0 at 0 MHz
Fix this by adding the missing entry, which results in:
CPU: Freescale i.MX8MMQ rev1.0 at 1200 MHz
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Before DM_VIDEO conversion this board used 24bpp
display configuration, so use it again.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Update the dummy clock names to use unique identifiers. Otherwise the
previous node just gets overwitten by the next one with the same name.
This fixes eMMC boot not working on J721e-evm.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
System firmware does not guarantee that clocks going out of the device
will be stable during power management configuration. There are some
DCRC errors when SPL tries to get the next stage during eMMC boot after
sysfw pm configuration.
Therefore add a config_pm_pre_callback() to switch off the eMMC clock
before power management and restart it after it is done.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The call to spl_mmc_get_uboot_raw_sector() completely ignores and
overwrites the raw_sect value passed from the caller of spl_mmc_load().
Fix this by passing raw_sect to the function and returning the same
value in the default case.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
With the latest RIOT, there is a different otap delay value for each
speed mode. Add a new binding with every supported speed mode. Also
disable a given speed mode in the host caps if its corresponding
otap-del-sel is not present.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Use cpu_x86_get_count() to read the number of cores.
cpu_x86_get_count() reads the number of CPUs from the device tree.
Using this function we can support multiple Apollo Lake
variants, e.g.: E3940 (4 cores) and E3930 (2 cores).
This was tested on the E3940 and E3930 Apollo Lake variants.
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The function cpu_x86_get_count() is also useful for other modules.
Make it non-static and add a prototype + description.
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Drop the Apollo Lake prefix 'apl' from the functions, types and
variables in the P2SB driver.
The P2SB is not Apollo Lake specific, and as such it was moved in
commit 2999846c11 ("x86: Move P2SB from Apollo Lake to a more generic
location") from the Apollo Lake folder to the intel_common folder.
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This reverts commit 0d67fac29f.
As real hardware testing (*) shows the above mentioned commit
breaks U-Boot on it. Revert for the upcoming release. We may get
more information in the future and optimize the code accordingly.
(*) on Intel Edison board.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: fix a typo in the commit message]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
This function doesn't use uclass_find_first_device() correctly. Add a
check that the device is found so we don't try to read properties from a
NULL device.
The fixes booting on minnoxmax.
Fixes: 87f1084a63 ("x86: Adjust mrccache_get_region() to use livetree")
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add initial support for the ABB SECU board, which is an ArriaV-based
SoCFPGA system with ethernet and booting from Denali NAND.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Add the "u-boot,dm-pre-reloc" property to the "ti,tilcdc,panel"
compatible node. In this way the video-uclass module can allocate the
amount of memory needed to be assigned to the frame buffer.
For boards that support Linux the property is added to the *-u-boot.dtsi
file since it is a u-boot specific dt flag.
Ran building tests with CONFIG_AM335X_LCD enabled and disabled for the
following configurations:
- brxre1_defconfig --> success
- am335x_guardian_defconfig --> success
- am335x_evm_defconfig --> success
- da850evm_defconfig --> failure with CONFIG_AM335X_LCD enabled
Enabling CONFIG_AM335X_LCD in da850evm_defconfig causes building errors
even without applying the patch. The driver has never been enabled on the
da850 and must be adapted for this platform.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Tested-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Felix Brack <fb@ltec.ch>
Update the driver to support the device tree and the driver model.
Timings and panel parameters are now loaded from the device tree.
The DM code replaces the am335x_lcdpanel structure with
tilcdc_panel_info taken from the linux kernel, as well the management
of additional parameters not covered in the legacy code. In addition,
the am335x_lcdpanel structure contains parameters and operations that
were probably a requirement of the board for which this driver was
developed and which, however, were not developed in the linux kernel.
All this led to rewrite th DM controller initialization code, except
for the pixel clock setting that is executed in a function created in a
previous patch with code taken from the legacy am335xfb_init.
The patch has been tested on a custom board with u-boot 2018.11-rc2 and
the following device-tree configuration:
panel {
compatible = "ti,tilcdc,panel";
pinctrl-names = "default";
pinctrl-0 = <&lcd_enable_pins>;
enable-gpios = <&gpio0 31 0>;
backlight = <&backlight>;
status = "okay";
u-boot,dm-pre-reloc;
panel-info {
ac-bias = <255>;
ac-bias-intrpt = <0>;
dma-burst-sz = <16>;
bpp = <16>;
fdd = <0x80>;
sync-edge = <0>;
sync-ctrl = <1>;
raster-order = <0>;
fifo-th = <0>;
};
display-timings {
native-mode = <&timing0>;
timing0: 800x480 {
hactive = <800>;
vactive = <480>;
hback-porch = <46>;
hfront-porch = <210>;
hsync-len = <20>;
vback-porch = <23>;
vfront-porch = <22>;
vsync-len = <10>;
clock-frequency = <33000000>;
hsync-active = <0>;
vsync-active = <0>;
};
};
};
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Tested-by: Dario Binacchi <dariobin@libero.it>
The ESM handling on J7 processor board requires routing the
MCU_SAFETY_ERROR signal to the PMIC on the board for critical safety
error handling. The PMIC itself should then reset the board based on
receiving it. Enable the support for the board by adding the esm
node in place.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Main domain ESM support is needed to configure main domain watchdogs
to generate ESM pin events by default. On J7 processor board these
propagate to the PMIC to generate a reset when watchdog expires.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Add fs_loader node which will be needed for loading firmwares
from the boot media/filesystem.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
MCU Domain rf50 is currently shutting down after loading the ATF.
Load elf firmware and jump to firmware post loading ATF.
ROM doesn't enable ATCM memory, so make sure that firmware that
is being loaded doesn't use ATCM memory or override SPL.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add MAIN domain R5FSS0 remoteproc support from spl. This enables
loading the elf firmware in SPL and starting the remotecore.
In order to start the core, there should be a file with path
"/lib/firmware/j7-main-r5f0_0-fw" under filesystem
of respective boot mode.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[Guard start_non_linux_remote_cores under CONFIG_FS_LOADER]
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Move the generic elf loading/validating functions to lib/
so that they can be re-used and accessed by code existing
outside cmd.
While at it remove the duplicate static version of load_elf_image_phdr
under arch/arm/mach-imx/imx_bootaux.c.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Suggested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Since ROM configures OSPI controller to be in memory mapped mode in OSPI
boot, R5 SPL can directly pass the memory mapped pointer to ROM. With
this ROM can directly pull the SYSFW image from OSPI.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Populate address mapping entries in A53 MMU for 4 GB of MMIO space
reserved for providing MMIO access to multiple flash devices through
OSPI/HBMC IPs within FSS.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
- Enable ADMA and HS400 for the eMMC driver on 64-bit SoCs
- Add some convenient environment variables to handle SD card
- Sanitize the NAND controller reset sequence and its WP handling
- Sync DT with Linux
-----BEGIN PGP SIGNATURE-----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=h4lQ
-----END PGP SIGNATURE-----
Merge tag 'uniphier-v2020.04-3' of https://gitlab.denx.de/u-boot/custodians/u-boot-uniphier
UniPhier SoC updates for v2020.04 (3rd)
- Enable ADMA and HS400 for the eMMC driver on 64-bit SoCs
- Add some convenient environment variables to handle SD card
- Sanitize the NAND controller reset sequence and its WP handling
- Sync DT with Linux
The compatible string "i2c-eeprom" is U-Boot own compatible, which
has never been approved by the DT community. "u-boot,i2c-offset-len"
is also a U-Boot own hack.
Linux adds "atmel,*" as generic compatibles, and U-Boot also followed
it by commit d7e28918aa ("i2c_eeprom: Add reading support").
The U-Boot own hack is no longer needed. Just sync with Linux.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Import the nodename changes I made in Linux for avoiding dt-schama
warnings. This follows the $nodename patterns in the dt-schema.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Commit f3729ba6e7 ("watchdog: mpc8xx_wdt: Watchdog driver and macros
cleanup") switched the watchdog to CONFIG_WATCHDOG. But this is not
compatible with the 8xx because it starts the watchdog HW timer at
reset and must be serviced from the very beginning including while
U-boot is executed in the firmware before relocation in RAM.
Select CONFIG_HW_WATCHDOG and make hw_watchdog_reset() visible.
Meanwhile, finalise the cleanup of arch/powerpc/cpu/mpc8xx/Kconfig by
removing the lines put in comment in that commit, and also remove
again the selection of CONFIG_MPC8xx_WATCHDOG which was removed by
that commit and brought back by mistake by commit b3134ffbd9
("watchdog: Kconfig: Sort entry alphabetically")
Note that there was an 'imply WATCHDOG' in the original commit but
it disappeared in the Kconfig alphabetical sorting, so no need to
remove it here.
Fixes: f3729ba6e7 ("watchdog: mpc8xx_wdt: Watchdog driver and macros cleanup")
Fixes: b3134ffbd9 ("watchdog: Kconfig: Sort entry alphabetically")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Stefan Roese <sr@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The base address 0x43f00000 is no longer true for the future SoC.
Extract the base address from the device tree.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This workaround was previously needed for LD4, Pro4, sLD8, Pro5
SoCs. The boot ROM does not touch this register for PXs2/LD6b or
later.
Now that the reset signal of the Denali NAND controller is always
asserted in board_init() then deasserted in the driver, the
WRITE_PROTECT register gets back to the default value, which means
the write protect is deasserted.
This workaround can go away entirely.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The comment /* deassert reset */ is wrong. It asserts the reset.
It no longer needs to stay in SPL. The NAND controller reset is
handled in the driver. So, this assert can be moved to the
board_init() of U-Boot proper.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add handy macros:
- sdscript: source boot.scr in the file system of the SD media
- sdboot : boot the kernel using the images in the file system
of the SD media
- sdscript: update the boot firmware in the SD media
(in raw block sectors)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Macro SZ_64K is undeclared. Include sizes.h to fix the compilation
error.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The sata of our powerpc platforms are updated. These changes is to
fit the driver probe.
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This reverts commit 856b9cdb53.
Commit 856b9cdb53 ("powerpc: mpc85xx: delete FSL_SATA for T2080QDS
board.") is to fit support sata DM mode, Now the driver will be reverted,
So revert it.
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Put the target entries for rk3399 devices in alphabetical order.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The implementation of dma_map_single() and dma_unmap_single() is
exactly the same for all the architectures that support them.
Factor them out to <linux/dma-mapping.h>, and make all drivers to
include <linux/dma-mapping.h> instead of <asm/dma-mapping.h>.
If we need to differentiate them for some architectures, we can
move the generic definitions to <asm-generic/dma-mapping.h>.
Add some comments to the helpers. The concept is quite similar to
the DMA-API of Linux kernel. Drivers are agnostic about what is
going on behind the scene. Just call dma_map_single() before the
DMA, and dma_unmap_single() after it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Added support for onboard LED's and push button. When powered board will be
in low power mode(yellow LED), on button press, board enters full power mode
(red LED) and boots u-boot.
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
roc-pc-rk3399 board has one user button & three user LED's. Currently
we don't have any code support for these devices. Since button and LED's are
specific to roc-pc-rk3399 board, split it into its own board file and add code
support here.
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
adc_channel_single_shot() requires the full device name e.g.
"saradc@ff100000", which differs between Rockchip SoC's, but they all
share the prefix "saradc"; find the ADC device with this name prefix and
use its full name.
Signed-off-by: Hugh Cole-Baker <sigmaris@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync rk3288-vyasa dts file from Linux.
This sync has changes required to work HDMI output on
Vyasa RK3288 board.
This sync excludes the io_domains node since it is not
available in rk3288.dtsi.
Changes like vcc50_hdmi, vdd10_lcd and ddc-i2c-bus are
not merged to Linux yet but wil resync later if any
further updates on this.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable pre console buffer for rk3288 platform.
This would help to capture the console messages prior to
the console being initialised. Enabling this would help
to capture all the console messages on video output source
like HDMI. So we can find the full console messages of
U-Boot proper on HDMI display when enabled it for RK3288
platform boards.
Buffer address used for pre console is 0x0f000000 which is
ram base plus 240MiB. right now the Allwinner SoC is using
similar computation.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
There have been multiple peripherals added to the main px30 dtsi
in the Linux kernel since its addition to u-boot. So to make it easier
to sync board devicetrees, update the core dtsi from Linux.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Move the U-Boot specific bits to a -u-boot.dtsi include so all the
u-boot.dtsi hierarchy is included.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
There's some bits in the U-Boot rk3399.dtsi that aren't yet in the
upstream Linux dtsi but are needed for early boot. This moves them
to the u-boot.dtsi to make it easier to sync the rest of rk3399.dtsi
with upstream.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The upstream linux kernel for the Rockchip 3399 SoC use usbdrd3 naming so move
the two remaining devices over to that for their device trees to make it
easier to sync with upstream DTs.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The core Rockchip spl code contains a default board_fit_config_name_match
implementation doing nothing. Individual boards may want to handle this
differently, so add a __weak atribute to make it possible to override
this function in other places.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The script iterates over the given devicetrees and creates both
fdt_x node as well as a conf-node for each passed dt.
But there is a slight bug in that it always references fdt_1 in each
conf node instead of the matching fdt_x as expected.
So fix that by referencing the number of the current dt similar to
how the fdt_x nodes gets created.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
- DT alignment with kernel v5.5-rc7 for stm32mp1 boards
- fix STM32 image format for big endian hosts in mkimage
- solve warnings in device tree and code for stm32mp1 boards
- remove fdt_high and initrd_high for stm32 and stih boards
- add support of STM32MP15x Rev.Z
- update stm32mp1 readme
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl5GcB0ACgkQ4rK92eCq
k3Wr9gf/dDPJi6UBhLDio/IVKDBddOEUN0Lwdr9W0upL+DrdvEOyNyMSEKuLccIE
UTd1NmNNwcvgDRaPvB5o3R7twWItTW0cYlmVkFSZ228aq6xdf/SElN2OUD6B9Gh+
8bi6oVLu41TNMYn4VYxsEftcT2megfH8s+SH/FlvR5ua1yCC1vyrytEQjPIbJAB2
sa90ewDyp5EYqGLdAk6AVjPLeNZsaleGwuyLf04PoC2xhn+3HTEKJCJN4O46aJUr
0GUI7YN7pTjIfZdYfFqjcwoQV1xV2HtbjCTcOb8Td8TEYjIoILF8tSyfIwDXWGB5
zMQIQxUdQyNiqdBPFcnkAufjk+zLIQ==
=0dG+
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20200214' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- add DH Electronics DHCOM SoM and PDK2 board
- DT alignment with kernel v5.5-rc7 for stm32mp1 boards
- fix STM32 image format for big endian hosts in mkimage
- solve warnings in device tree and code for stm32mp1 boards
- remove fdt_high and initrd_high for stm32 and stih boards
- add support of STM32MP15x Rev.Z
- update stm32mp1 readme
Add support for Rev.Z of STM32MP15x cpu.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Fix the following DT dtc warnings for stm32mp1 boards:
Warning (unit_address_vs_reg): /soc/rcc@50000000/st,pll@0:
node has a unit name, but no reg property
Warning (unit_address_vs_reg): /soc/rcc@50000000/st,pll@1:
node has a unit name, but no reg property
Warning (unit_address_vs_reg): /soc/rcc@50000000/st,pll@2:
node has a unit name, but no reg property
Warning (unit_address_vs_reg): /soc/rcc@50000000/st,pll@3:
node has a unit name, but no reg property
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
This patch fix the warning:
dt.dts: Warning (simple_bus_reg): Node /soc/ddr@5A003000
simple-bus unit address format error, expected "5a003000"
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
LTDC modifies the clock frequency to adapt it to the display. Such
frequency change is not detected by the FDCAN driver that instead
cache the value at probe and pretend to use it later.
Keep the LTDC alone on PLL4_Q by moving the FDCAN to PLL4_R.
Signed-off-by: Antonio Borneo <antonio.borneo@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Device tree and binding alignment with kernel v5.5-rc7
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Update the driver to use the latest binding from kernel v5.5-rc1:
no more use syscon or regmap to access to pwr register and
only one pwr_regulators node with the compatibility "st,stm32mp1,pwr-reg"
is available.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Device tree and binding alignment with kernel v5.4
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Activate early console functionality on AM65x devices to allow for
early diagnostic messages until the main console is ready
to get activated.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The boot parameter table index memory address for J721E was configured
to an incorrect value which prevented the use of this definition to
determine which boot parameter table is active which is needed to be
able to distinguish between primary and backup boot modes. Fix this
issue by updating the value to the correct one also in alignment with
the J721E Technical Reference Manual (TRM).
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Data manual mentions the new silicon revisions as SR instead of PG. Use
the same nomenclature inside U-Boot as well.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
mcu uart will be used during uart boot for loading sysfw.itb. Since
sysfw is not yet available during uart load, power-domain cannot be
enabled. We need to rely on ROM for doing that, so disable power-domains
and clocks for mcu uart. Also fix the mcu uart frequency.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add scm_conf syscon node and its parents as well as the ethernet phy
node to u-boot.dtsi. This enables ethernet boot.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add support for DH Electronics DHCOM SoM and PDK2 rev. 400 carrier
board. This is an SoM with STM32MP15xx and an evaluation kit. The
baseboard provides Ethernet, UART, USB, CAN and optional display.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
First of all U-Boot is not that performance oriented as real run-time
software like OS or user bare-metal app so we may afford being not super
fast as we only being executed once. That in return allows us to be more
universal and support wider variety of devices.
And looking forward that will significantly reduce maintenance and simplify
support of newer architectures.
And while at it we add quad-word accessors like readq(), writeq() etc.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
It's a very rare if at all existing occasion when ARC CPU template
is used as is w/o any changes - in the end it's a beauty and competitive
advantage of ARC cores to be tailored for a particular use-case - and
so it doesn't make a lot of sense to offer template-based "-mcpu" selection.
Given for each and every platform we end-up adding quite a few more flags
it's logical to move "-mcpu" selection to platform's definition as well
which we exactly do here.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Given now nsim_hs38 configuration is usable on QEMU and in QEMU
we have Virtio working perfectly fine the next logical step
is to add support of supported & known to work net & bkl to this
config.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Since v2019.06 DesingWare nSIM supports DesignWare UART simulation
and so we may switch from pretty unusual ARC UART to much more standard
DesignWare UART (which in case of U-Boot is just an ordinary 16650 UART).
This among other things makes built dinaries compatible with our other
platforms to name a few: FPGA-based HAPS boards, QEMU and even ZeBU.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
TPM TEE driver
Various minor sandbox video enhancements
New driver model core utility functions
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl48iogACgkQfxc6PpAI
reaVzAf/an3/yKe6r3CVWlcRV6H/dVg1ApnnLpX7jS0p0b++oCVvOiy7z1WPXj3k
b1SSgENDeeZ/8EHio+Gf7ZidH/TGEj7L6YEFwd1t60GMkZiWEkNf4Z53tw482YG+
96hoPD+ySTW+ddIdVHWAFG2I4aEiKHANJAp/ItNdD+rLbrEwNQy+eiK5JTOk80B6
/X8AJCLZeAC1s7vs+2+WolgjT78QGzA9HHalMiublcqh0ivKKk0QeQiOKKPe8JYJ
om5YY1TxayQ60Xmo5f39/SBfzEEklxw83sU9o1tBeYzyVUpu7fQdkxiDbWdsij77
DgwLdeYQJGbN+hdSWE0gjTqyhW+lWA==
=KRoA
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-6feb20' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm
sandbox conversion to SDL2
TPM TEE driver
Various minor sandbox video enhancements
New driver model core utility functions
- Move P2SB from Apollo Lake to a more generic location
- Add a function to find a device by drvdata in DM core
- Enhancement of DM IRQ uclass driver
- Add a clock driver for Intel devices
- Add support for ACPI general-purpose events
- Add a TPM driver for H1/Cr50
- Enable TPM on Google Chromebook Coral
The add instruction on risc-v can have any three sources and targets, so there
is no need for an intermediate mov.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When debugging, it can be helpful to see more information about an
unhandled exception. This patch adds an option to view the registers at
the time of the trap, similar to the linux output on a kernel panic.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Due to the two-instruction sequence needed to access arbitrary memory
locations, the RISC-V linker aggressively optimises memory accesses and
jumps at link-time. This is called "linker relaxation," and is discussed
in this SiFive article
<https://www.sifive.com/blog/all-aboard-part-3-linker-relaxation-in-riscv-toolchain>.
One of the optimizations in place is to assume that the __global_pointer
symbol is placed in the gp register. To quote the article:
"...The magic __global_pointer$ symbol is defined to point 0x800 bytes
past the start of the .sdata section. The 0x800 magic number allows
signed 12-bit offsets from __global_pointer$ to address symbols at the
start of the .sdata section. The linker assumes that if this symbol is
defined, then the gp register contains that value, which it can then use
to relax accesses to global symbols within that 12-bit range. The
compiler treats the gp register as a constant so it doesn't need to be
saved or restored, which means it is generally only written by _start,
the ELF entry point."
However, U-Boot instead keeps the global data pointer in gp. This causes
memory accesses and jumps optimized to use the gp pointer to fail. To
fix this problem, we undefine the __global_pointer symbol.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Override the panel compatible string for LCD in U-Boot.
Include U-Boot device tree overrides in device-specific device trees so
that the panel compatible string is used.
Fixes: 8c26739859 ("board: ge: bx50v3: sync devicetrees from Linux")
Signed-off-by: Ian Ray <ian.ray@ge.com>
Enable DM_VIDEO for mx53ppd.
Enable DM_REGULATOR_FIXED and DM_PWM for the backlight.
Remove unused MX53PPD_LCD_POWER.
Remove old (incorrect) setup_iomux_lcd.
Enable backlight via display enable handler.
Use cls command to initiate display in HW agnostic manner.
Modify `failbootcmd' to use lcdputs.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Add bootcount node, linking to i2c eeprom "bootcount" partitions for
storage.
Enable i2c eeprom bootcount backend storage.
Enable bootcount command and use it for failbootcmd.
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Add bootcount node, linking to i2c eeprom "bootcount" partitions for
storage.
Enable i2c eeprom bootcount backend storage.
Enable bootcount command and use it for failbootcmd.
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Remove old (pre-DM) i2c setup code.
Enable DM i2c.
Convert common code to use DM rtc.
Convert common code to read VPD from eeprom partition.
Convert the generic i2c PMIC init code to use the new da9063 driver.
mx53ppd only:
Correct RTC compatible in device tree.
Enable MXC DM i2c driver.
Define CONFIG_SYS_MALLOC_F_LEN so that DM is available in pre-reloc.
Make GPIO banks available during preloc, since initialisation is done
in board_early_init_f().
Add gpio_request() calls to satisfy the DM_GPIO compatibility API.
Remove unused power configuration.
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Signed-off-by: Ian Ray <ian.ray@ge.com>
Just move the defconfig entries which are required into the Novena
entry in arch Kconfig, no functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Vagrant Cascadian <vagrant@debian.org>
These nodes are not in upstream kernel, so move these in u-boot.dtsi
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The 'enable-active-high' DTS property configures GPIO so it is active with
HIGH state (by default it is low).
The 'regulator-boot-on' property indicates that the regulator was enabled
in the 'earlier' stage - i.e. bootloader/firmware.
In the XEA case the 'fec-3v3' was configured (as a "wrapper" on GPIO0_0) in
very early SPL code, so it shouldn't be modified at latter stages.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This adds initial minimal support for the Toradex Verdin iMX8M Mini Quad
2GB WB IT V1.0A module. They are now strapped to boot from eFuses which
are factory fused to properly boot from their on-module eMMC. U-Boot
supports booting from the on-module eMMC only, SDP support is disabled
for now due to missing i.MX 8M Mini USB support.
Functionality wise the following is known to be working:
- eMMC, 8-bit and 4-bit MMC/SD card slots
- Ethernet
- GPIOs
- I2C
Boot sequence is:
SPL ---> ATF (TF-A) ---> U-boot proper
ATF, U-boot proper and u-boot.dtb images are packed into a FIT image,
loaded by SPL.
Boot:
U-Boot SPL 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100)
Normal Boot
Trying to boot from MMC1
NOTICE: Configuring TZASC380
NOTICE: RDC off
NOTICE: BL31: v2.0(release):rel_imx_4.14.98_2.3.0-0-g09c5cc994-dirty
NOTICE: BL31: Built : 01:11:41, Jan 25 2020
NOTICE: sip svc init
U-Boot 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100)
CPU: Freescale i.MX8MMQ rev1.0 at 0 MHz
Reset cause: POR
DRAM: 2 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... OK
In: serial
Out: serial
Err: serial
Model: Toradex Verdin iMX8M Mini Quad 2GB Wi-Fi / BT IT V1.0A, Serial#
06535149
Net: eth0: ethernet@30be0000
Hit any key to stop autoboot: 0
Verdin iMX8MM #
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
The Cortina CAxxxx GPIO driver maintains DM_GPIO support
across different CPU ISA in the CAxxxx Soc Family; Not just ARM.
Therefore, it is not desirable to split out and maintain separete
gpio header file for each CPU architecture.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Jason Li <jason.li@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
To match the other PowerPC platforms the function show_regs() must not
be marked static but instead be an exposed global function.
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Christophe Leroy <christophe.leroy@c-s.fr>
Add nodes to the device tree for Cr50 and other available I2C ports. Also
enable the ACPI interrupt driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
ACPI GPEs are used to signal interrupts from peripherals that are accessed
via ACPI. In U-Boot these are modelled as interrupts using a separate
interrupt controller. Configuration is via the device tree.
Add a simple driver for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present driver model supports the IRQ uclass but there is no way to
request a particular interrupt for a driver.
Add a mechanism, similar to clock and reset, to read the interrupts
required by a device from the device tree and to request those interrupts.
U-Boot itself does not have interrupt-driven handlers, so just provide a
means to read and clear an interrupt. This can be useful to handle
peripherals which must use an interrupt to determine when data is
available, for example.
Bring over the basic binding file as well, from Linux v5.4. Note that the
older binding is not supported in U-Boot; the newer 'special form' must be
used.
Add a simple test of the new functionality.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Allow this driver to be used in TPL by setting up the interrupt type
correctly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add an IRQ type to each driver and use irq_first_device_type() to find
and probe the correct one.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
There can be different types of interrupt controllers in a system and some
drivers may need to distinguish between these. In general this can be
handled using the device tree by adding the interrupt information to
device nodes.
However on x86 devices we have interrupt controllers which are not tied
to any particular device and not really used in U-Boot. These still need
to be inited, so a convenient method is to give each controller a type
and allow a particular controller type to be probed.
Add support for this in sandbox along with a test.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: remove the new bland line at EOF of test/dm/irq.c]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
This config is not actually used here and in U-Boot it seems better to set
this using the device tree for each individual controller. The monolithic
config of the FSP-S is only necessary if the FSP is actually configuring
something, but here it is not.
The FSP-S does enable/disable the various I2C ports. It might be nice to
handle this using the okay/disabled property of each port, but that can be
considered later.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Enable the Intel clock driver and modify coral's device tree to use it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The Primary to Sideband Bridge (P2SB) is not specific to Apollo Lake, so
move its driver to a common location within arch/x86.
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present dm/device.h includes the linux-compatible features. This
requires including linux/compat.h which in turn includes a lot of headers.
One of these is malloc.h which we thus end up including in every file in
U-Boot. Apart from the inefficiency of this, it is problematic for sandbox
which needs to use the system malloc() in some files.
Move the compatibility features into a separate header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present devres.h is included in all files that include dm.h but few
make use of it. Also this pulls in linux/compat which adds several more
headers. Drop the automatic inclusion and require files to include devres
themselves. This provides a good indication of which files use devres.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Add a new device-tree property to control the colour depth. At present we
support 16bpp and 32bpp.
While we are here, update the code to use livetree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
On high-DPI displays U-Boot's LCD window can look very small. Add a
-K flag to expand it to make things easier to read, while still using
the existing resolution internally.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Sandbox currently uses SDL1.2. SDL2 has been around for quite a while and
is widely supported. It has a number of useful features. It seems
appropriate to move sandbox over.
Update the code to use SDL2 instead of SDL1.2.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present when audio stops, any in-progress output is cut off. Fix this
by waiting for output to finish.
Also use booleans for the boolean variables.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present there is no positive indication that U-Boot has finished
sending sound data. This means that it is not possible to power down an
audio codec, for example. Add a new method that is called once all sound
data has been sent.
Add a new method for this, called when the sound_play() call is done.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some files use U-Boot headers but still need to access the system
malloc(). Allow this by creating a new asm/malloc.h which can be used so
long as U-Boot's malloc.h has not been included.
Signed-off-by: Simon Glass <sjg@chromium.org>
The last member of this array is supposed to be all zeroes according to
the getopt_long() man page. Fix the function to do this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some sandbox files are not built with U-Boot headers, so with the renamed
malloc functions there is now no need to use the special os_... allocation
functions to access the system routines. Instead we can just call them
directly.
Update the affected files accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present options are presented in essentially random order. It is easier
to browse them if they are sorted into alphabetical order. Adjust the
help function to handle this.
Signed-off-by: Simon Glass <sjg@chromium.org>
If CONFIG_CMDLINE=n, common/cli.c calls board_run_command. This fails to
link on most architectures. However, the sandbox architecture has an
implementation which we can use.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Add a function to read a property from the chosen node, providing access
to its length. Update ofnode_get_chosen_string() to make use of it.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function is actually intended to read a string rather than a
property. All of its current callers use it that way. Also there is no way
to return the length of the property from this function.
Rename it to better indicate its purpose, using ofnode_read as the prefix
since this matches most other functions.
Also add some tests which are missing for these functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
- add dfu support to dwc2 for bcm2835
- enable DFU for RPi4
- Fix RPi4 memory map to include the genet device
- add driver for the genet ethernet device
- enable network support in RPi4 config
-----BEGIN PGP SIGNATURE-----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=Sv9b
-----END PGP SIGNATURE-----
Merge tag 'rpi-next-2020.04' of https://gitlab.denx.de/u-boot/custodians/u-boot-raspberrypi
- DFU support file operations lager then the default max size
- add dfu support to dwc2 for bcm2835
- enable DFU for RPi4
- Fix RPi4 memory map to include the genet device
- add driver for the genet ethernet device
- enable network support in RPi4 config
Add DDR2 support to Gen5 DRAM driver. As the DDR2 macro names generated
by Quartus are named differently than the DDR3 ones, use anon unions to
store them in the same structures, without growing their size.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Convert the designware watchdog timer driver to DM and add DT probing
support. Perform minor coding style clean up, like drop superfluous
braces. These ought to be no functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dalon Westergreen <dwesterg@gmail.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Philipp Tomisch <philipp.tomisch@theobroma-systems.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # roc-rk3399-pc
- Various minor fixes for x86
- Switch to ACPI mode on Intel edison
- Support run-time configuration for NS16550 driver
- Update coreboot and slimbootloader serial drivers to use NS16550
run-time configuration
- ICH SPI driver fixes to hardware sequencing erase case
- Move ITSS from Apollo Lake to a more generic location
- Intel GPIO driver bug fixes
- Move to vs2017-win2016 platform build host for Azure pipelines
This supports i2c DM and enables CONFIG_DM_I2C
for SoC LS1012A
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Fix below SPL build error when DM_I2C is enabled,
- arch/arm/cpu/armv8/built-in.o: In function `board_init_f:
arch/arm/cpu/armv8/fsl-layerscape/spl.c:74: undefined reference to `i2c_init_all'
arch/arm/cpu/armv8/fsl-layerscape/spl.c:74:(.text.board_init_f+0x30):
relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol
`i2c_init_all'
make[2]: *** [spl/u-boot-spl] Error 1
make[1]: *** [spl/u-boot-spl] Error 2
make: *** [sub-make] Error 2
arch/arm/cpu/armv8/fsl-layerscape/spl.c: In function 'board_init_f':
arch/arm/cpu/armv8/fsl-layerscape/spl.c:74:2: warning: implicit
declaration of function 'i2c_init_all'; did you mean 'misc_init_r'?
[-Wimplicit-function-declaration]`
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Sync the interrupt properties with the ones from Linux. Also use the
constants provided by the dt-bindings header. Please note, that there
are actual changes/fixes in the irq flags. U-Boot won't use the
interrupt properties anyway. It's just to be consistent with the Linux
device tree.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Also align the fspi node with the kernel one.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The Interrupt Timer Subsystem (ITSS) is not specific to Apollo Lake, so
remove the apl-prefix of the implemented functions/structures/...
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a Kconfig option to support enabling/disabling the inclusion of
the ITSS driver depending on the platform.
Atuomatically select the ITSS driver when building for Apollo Lake.
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: squashed in http://patchwork.ozlabs.org/patch/1232761/]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
The Interrupt Timer Subsystem (ITSS) is not specific to Apollo Lake, so
move it to a common location within arch/x86.
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: conditionally build itss.c]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
IO expanders are required to power cycle SD card. So enable the same
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
J721e SoC has 2 I2C instances in MCU domain and 7 I2C instances in main
domain. Add DT nodes for the same
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Enable USB0 in peripheral mode so that it be used for DFU
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add support to download SYSFW into internal RAM via DFU in DFU boot
mode. Prepare a DFU config entity entry dynamically using buffer address
allocated for SYSFW and start DFU gadget to get SYSFW.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
J721e does not support USB Host MSC boot, but only supports DFU boot.
Since BOOT_DEVICE_USB is often used for host boot mode and
BOOT_DEVICE_DFU is used for DFU boot, rename BOOT_DEVICE_USB macro to
BOOT_DEVICE_DFU
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The code in this file is not specific to Apollo Lake. According to
coreboot sources (where this code comes from), it is common to at least:
* Apollo Lake
* Cannon Lake
* Ice Lake
* Skylake
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
ITSS stands for "Interrupt Timer Subsystem", so add that term to the
description of the relevant files.
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The fs segment is only used to get the global data pointer.
If it is accessed beyond sizeof(new_gd->arch.gd_addr), it is a bug.
To specify the byte-granule limit size, drop the G bit, so the
flag field is 0x8093 instead of 0xc093, and set the limit field
to sizeof(new_gd->arch.gd_addr) - 1.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: fixed the comments about FS segement]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
I do not know why the boot code immediately after the system reset
should write-back the cache content. I think the cache invalidation
should be enough.
I tested this commit with qemu-x86_defconfig, and it worked for me.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Slim Bootloader provides serial port info in its HOB to support
both IO or MMIO serial ports, but it's controlled by SYS_NS16550_MEM32
or SYS_NS16550_PORT_MAPPED in U-Boot.
To support both serial port configurations dynamically at runtime,
Slim Bootloader serial driver leverages NS16550_DYNAMIC.
Signed-off-by: Aiden Park <aiden.park@intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: remove the obsolete comments for data->type]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Use this UART to improve the compatibility of U-Boot when used as a
coreboot payload.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Since mid 2016, coreboot has additional fields in the serial struct that
it passes down to U-Boot. Add these so we are in sync.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This particular chunk of code was not updated, likely due to the order
in which the patches were posted and applied. Fix this missing part.
Fixes: bb25aca134 ("arm: socfpga: Convert reset manager from struct to defines")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dalon Westergreen <dwesterg@gmail.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Denali NAND driver changes:
- Set up more registers in denali-spl for SOCFPGA
- Make clocks optional
- Do not assert reset signals in the remove hook
- associate SPARE_AREA_SKIP_BYTES with DT compatible
- switch to UCLASS_MTD
UniPhier platform changes:
- fix a bug in dram_init()
- specify loadaddr for "source" command
-----BEGIN PGP SIGNATURE-----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=PvYc
-----END PGP SIGNATURE-----
Merge tag 'uniphier-v2020.04-2' of https://gitlab.denx.de/u-boot/custodians/u-boot-uniphier
UniPhier SoC updates for v2020.04 (2nd)
Denali NAND driver changes:
- Set up more registers in denali-spl for SOCFPGA
- Make clocks optional
- Do not assert reset signals in the remove hook
- associate SPARE_AREA_SKIP_BYTES with DT compatible
- switch to UCLASS_MTD
UniPhier platform changes:
- fix a bug in dram_init()
- specify loadaddr for "source" command
gd->ram_base is not set at all if the end address of the DRAM ch0
exceeds the 4GB limit.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
UCLASS_MTD is a better fit for NAND drivers.
Make NAND_DENALI_DT depend on DM_MTD, which is needed to compile
drivers/mtd/mtd-uclass.c
Also, make ARCH_UNIPHIER select DM_MTD because all the defconfig
of this platform enables NAND_DENALI_DT.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Now that the reset controlling of the Denali NAND driver (denali_dt.c)
works for this platform, remove the adhoc reset deassert code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add alias for mmc/sdmmc so that we can have a fix mmc number for emmc.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Add rk3328-sdram-ddr4-666.dtsi for support ddr4 init.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
All rockchip platforms support TPL or SPL-based bootloader
in mainline with U-Boot proper as final stage. For each
stage we need to burn the image on to flash with respective
offsets.
This patch creates a single boot image component using
- binman, for arm32 rockchip platforms
- pad_cat, for arm64 rockchip platforms.
This would help users to get rid of burning different
boot stage images.
The new image called 'u-boot-rockchip.bin'
which can burn into flash like:
₹ sudo dd if=u-boot-rockchip.bin of=/dev/sda seek=64
This would support all rockchip platforms, except rk3128
since it doesn't support for SPL yet.
Cc: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Cc: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add U-Boot specific dtsi file for rk3188 SoC. This
would help to add U-Boot specific dts nodes, properties
which are common across rk3188.
Right now, the file is empty, will add required changes
in future patches.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add U-Boot specific dtsi file for rk3036 SoC. This
would help to add U-Boot specific dts nodes, properties
which are common across rk3036.
Right now, the file is empty, will add required changes
in future patches.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add bootcount support for Rockchip rk3399.
The bootcount value is preserved in PMU_SYS_REG0 register,
this would help to support redundent boot.
Once the redundant boot triggers, the altboot command
will look for extlinux-rollback.conf on particular
bootable partition which supposed to be a recovery
partition where redundant boot required.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add cpu reset cause in common cpu-info file.
This would help to print the reset cause for
various resets.
Right now it support rk3288, rk3399. rest of rockchip
platforms doesn't have reset cause support ye but this
code is more feasible to extend the same.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Few of the rockchip family SoC atleast rk3288,
rk3399 are sharing some cru register bits so
adding common code between these SoC families
would require to include both cru include files
that indeed resulting function declarations error.
So, create a common cru include as cru.h then
include the rk3399 arch cru include file and move
the common cru register bit definitions into it.
The rest of rockchip cru files will add it in future.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add cpu information for rockchip soc.
This would help to print the SoC family number, with
associated temparature, clock and reason for reset etc.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Enable winbond SPI flash for ROC-PC-RK3399 board.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable winbond SPI flash for ROC-PC-RK3399 board.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync the ROC-RK3399-PC device tree changes from Linux
with below commit details:
commit <c36308abe4110e4db362d5e2ae3797834a7b1192> ("arm64: dts:
rockchip: Enable MTD Flash on rk3399-roc-pc")
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Some of the devices(for instance, pcie and gnet controller) sitting on
SCB bus falls behind/below the memory range that we currenty have.
This patch updates the memory range to map those devices correctly.
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
XOM pins provide information for iROM bootloader about the boot device.
Those pins are mapped to lower bits of OP_MODE register (0x10000008),
which is common for all Exynos SoC variants. Set the default MMC device id
to reflect the boot device selected by XOM[7:5] pins (2 for the SD or 0 for
the eMMC).
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Since frac_pll_init() is only used in this file, change it to 'static'.
This fixes the following sparse warning:
arch/arm/mach-imx/imx8m/clock_imx8mq.c:662:5: warning: no previous
prototype for ‘frac_pll_init’ [-Wmissing-prototypes]
Signed-off-by: Pedro Jardim <jardim.c.pedro@gmail.com>
