Commit graph

3326 commits

Author SHA1 Message Date
Roger Quadros
d59baeb76f ARM: OMAP5+: sata: Move scsi_scan() to the right place
scsi_scan() must be called as part of scsi_init() and not
as part of sata_init().

Signed-off-by: Roger Quadros <rogerq@ti.com>
2014-10-10 09:44:42 -04:00
Roger Quadros
3160b1b986 OMAP5+: sata/scsi: Implement scsi_init()
On OMAP platforms, SATA controller provides the SCSI subsystem
so implement scsi_init().

Get rid of the unnecessary sata_init() call from dra7xx-evm
and omap5-uevm board files.

Signed-off-by: Roger Quadros <rogerq@ti.com>
2014-10-10 09:44:42 -04:00
Albert ARIBAUD
ebf8644a11 Merge branch 'u-boot-samsung/master' into 'u-boot-arm/master' 2014-10-10 08:56:01 +02:00
Nobuhiro Iwamatsu
88982893c4 arm: rmobile: r8a7794: Skip initialize L2 cache
rmobile/lowlevel_init_ca15.S are common in r8a7790, r8a7791 and r8a7794 of
rmobile SoCs.  The initialize L2 cache in lowlevel_init_ca15.S only needed
for Cortex-A15. The r8a7794 is Cortex-A7, not Cortex-A15.
This adds Skip to initialize L2 cache when r8a7794.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2014-10-09 14:45:03 +09:00
Nobuhiro Iwamatsu
237faf095f arm: rmobile: r8a7791: Fix initialize L2 cache
rmobile/lowlevel_init_ca15.S are common in r8a7790 and r8a7791 of
rmobile SoC. But L2 cache of r8a7791 does not use L2CTLR[5].
This adds fix to set L2CTLR [5] only when the r8a7790.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2014-10-09 14:45:03 +09:00
Nobuhiro Iwamatsu
7d83580364 arm: rmobile: Remove unnecessary initialization for l2ctlr
This removes duplicate initialization of l2ctlr.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2014-10-09 14:45:03 +09:00
Albert ARIBAUD
4b19b7448e Merge remote-tracking branch 'u-boot-imx/master'
The single file conflict below is actually trivial.

Conflicts:
	board/boundary/nitrogen6x/nitrogen6x.c
2014-10-08 21:20:49 +02:00
Robert Baldyga
dab067c323 armv7: s5pc1xx: improve cache handling
Move cache handling code to C file, and add enable_caches() and
disable_caches() functions.

Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-10-08 19:42:04 +09:00
Simon Glass
93327f6976 samsung: Enable device tree for smdkc100
Change this board to add a device tree.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-10-08 17:25:48 +09:00
Simon Glass
311757be27 samsung: Enable device tree for s5p_goni
Change this board to add a device tree.

This also adds a pinmux header file although it is not used as yet.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-10-08 17:25:47 +09:00
Simon Glass
1d55110003 config: Move smdkv310 to use common exynos4 file
Most of the smdkv310 features are common with other exynos4 boards. To
permit easier addition of driver model support, use the common file and
add a device tree file.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-10-08 17:25:47 +09:00
Simon Glass
f0d80fbcd7 exynos: dts: Add device tree node for cros_ec keyboard
Add a keyboard definition so that the keyboard can be used on pit.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-10-08 17:25:47 +09:00
Simon Glass
e4d761000a Exynos: Use 900MHz ARM frequency in SPL for peach_pit
The device seems to hang in SPL if the full speed is used when booting from
USB, perhaps because the PMIC has not been set to the maximum ARM core
voltage yet. Slow it down to a reliable speed.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-10-08 17:25:46 +09:00
Tom Rini
dd0204e48d Merge branch 'master' of git://git.denx.de/u-boot-arm 2014-10-07 07:38:39 -04:00
Anthony Felice
c19a8bc571 vf610twr: Tune DDR initialization settings
Removed settings in unsupported register fields. They didn’t
do anything, and in most cases, were not documented in the
reference manual.

Changed register settings to comply with JEDEC required values.

Changed timing parameters because they included full clock
periods that were doing nothing.

Signed-off-by: Anthony Felice <tony.felice@timesys.com>
[rebased on v2014.10-rc2]
Signed-off-by: Stefan Agner <stefan@agner.ch>
2014-10-07 13:08:31 +02:00
Marek Vasut
7249fafb1a arm: socfpga: Add command to control HPS-FPGA bridges
Add command to enable and disable the bridges between HPS and FPGA.

This patch does have a checkpatch issue with the assembler portion,
checkpatch correctly complains that there should be no whitespace
before quoted newline. I do not agree that fixing this specific
checkpatch issue will improve the readability, thus this one is not
addressed.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Wolfgang Denk <wd@denx.de>
2014-10-06 17:46:51 +02:00
Marek Vasut
4ab333b765 arm: socfpga: Move cache_enable to CPU code
Move icache_enable() and dcache_enable() function calls from
board code into the CPU code and into the enable_caches()
function. This is how the cache enabling code was designed
to work.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
2014-10-06 17:46:51 +02:00
Pavel Machek
13e81d45f8 arm: socfpga: nic301: Add NIC-301 configuration code
Add code which configures the AMBA NIC-301 and the SCU on the SoCFPGA .
The code sets the access permissions for the CPU to the AMBA slaves such
that the CPU can access them in both secure and non-secure mode.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
2014-10-06 17:46:51 +02:00
Marek Vasut
60d804c2f3 arm: socfpga: pl310: Map SDRAM to 0x0
Configure the PL310 address filter to make sure DRAM is mapped to 0x0.
This code also configures the "remap" register of NIC-301 and sets the
required 'mpuzero' bit.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
2014-10-06 17:46:50 +02:00
Marek Vasut
7056efcc32 arm: socfpga: nic301: Add NIC-301 GPV register file
Add register definition for the NIC-301 used on SoCFPGA.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
2014-10-06 17:46:50 +02:00
Marek Vasut
181d363852 arm: socfpga: scu: Add SCU register file
Add the Snoop Control Unit register definition file.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
2014-10-06 17:46:50 +02:00
Marek Vasut
807abb18f1 arm: socfpga: sysmgr: Add FPGA bits into system manager
Add missing system manager bits from Altera U-Boot to make the code
comparable. These are the bits which depend on the FPGA manager.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
2014-10-06 17:46:50 +02:00
Marek Vasut
abb25f4e95 arm: socfpga: reset: Add function to reset FPGA bridges
Add function to enable and disable FPGA bridges. This code is used
by the FPGA manager to disable the bridges before programming the
FPGA and will later be also used by the initialization code for the
chip to put the chip into well defined state during startup.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
2014-10-06 17:46:50 +02:00
Pavel Machek
230fe9b202 arm: socfpga: fpga: Add SoCFPGA FPGA programming interface
Add code necessary to program the FPGA part of SoCFPGA from U-Boot
with an RBF blob. This patch also integrates the code into the
FPGA driver framework in U-Boot so it can be used via the 'fpga'
command.

Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>

V2: Move the not-CPU specific stuff into drivers/fpga/ and base
    this on the cleaned up altera FPGA support.
2014-10-06 17:46:50 +02:00
Pavel Machek
d5a3d3c9ef arm: socfpga: misc: Align print_cpuinfo() output
Cosmetic change to the print_cpuinfo() function output. Align the
output with the rest of initial output produced by U-Boot.

Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
2014-10-06 17:46:49 +02:00
Pavel Machek
4e736869c6 arm: socfpga: misc: Add SD controller init
Add CPU function to register and initialize the dw_mmc SD controller.
This allows us to use the HPS SDMMC block.

Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
2014-10-06 17:46:49 +02:00
Pavel Machek
45d6e67710 arm: socfpga: misc: Add proper ethernet initialization
Add function to initialize the EMAC blocks upon board startup.
The preprocessor guards against building on SoCFPGA-VT and against
SPL build are not needed as those are handled implicitly via both
SPL framework and the socfpga_cyclone5.h config file, which will
not define CONFIG_DESIGNWARE_ETH if building for SoCFPGA-VT.

We cannot handle two EMAC ethernet blocks yet, therefore the ifdefs.
Once there is hardware using both EMAC blocks, this ifdef will have
to go.

Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
2014-10-06 17:46:49 +02:00
Marek Vasut
e9d6a20034 arm: socfpga: reset: Add EMAC reset functions
Add functions to reset the EMAC ethernet blocks. We cannot handle
two EMAC ethernet blocks yet, therefore the ifdefs. Once there is
hardware using both EMAC blocks, this ifdef will have to go.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
2014-10-06 17:46:49 +02:00
Marek Vasut
2110eeaf0f arm: socfpga: timer: Pull the timer reload value from config file
The timer reload value is a property of the timer hardware and there
is no reason for this to be configurable. Place this into the timer
driver just like on the other hardware.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Pavel Machek <pavel@denx.de>
2014-10-06 17:46:49 +02:00
Marek Vasut
036ba54f5b arm: socfpga: clock: Sync with reference code
Add the missing pieces from the reference clock code from Altera. This
puts the code on par with the Altera U-Boot fork for all but the SDRAM
self-refresh bits, which are not part of this patch.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
2014-10-06 17:46:49 +02:00
Marek Vasut
44428ab6ab arm: socfpga: clock: Clean up bit definitions
Clean up the clock code definitions so they are aligned with mainline
standards. There are no functional changes in this patch.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
2014-10-06 17:46:49 +02:00
Marek Vasut
5d8ad0cd3a arm: socfpga: clock: Trim down code duplication
Pull out functions to read frequency of Main clock VCO and
PLL clock VCO as the code is duplicated multiple times.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Pavel Machek <pavel@denx.de>
2014-10-06 17:46:49 +02:00
Pavel Machek
a832ddba55 arm: socfpga: clock: Add code to read clock configuration
Add the entire bulk of code to read out clock configuration from the SoCFPGA
CPU registers. This is important for MMC, QSPI and UART drivers as otherwise
they cannot determine the frequency of their upstream clock.

Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>

V2: Fixed the L4 MP clock divider and synced the clock code with latest
    rocketboards codebase (thanks Dinh for pointing this out)
2014-10-06 17:46:49 +02:00
Marek Vasut
4425e62856 arm: socfpga: clock: Drop nonsense inlining from clock manager code
The inlining is done by GCC when needed, there is no need to do it
explicitly. Furthermore, the inline keyword does not force-inline
the code, but is only a hint for the compiler. Scrub this hint.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Pavel Machek <pavel@denx.de>
2014-10-06 17:46:48 +02:00
Marek Vasut
09f7e314e4 arm: socfpga: clock: Implant order into bit definitions
The bit definitions for clock manager are complete chaos. Implement
some basic logical order into them.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
2014-10-06 17:46:48 +02:00
Marek Vasut
665e4caf02 arm: socfpga: sysmgr: Clean up system manager
Clean up the system manager register definition and add the missing
register definitions in place.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
2014-10-06 17:46:48 +02:00
Pavel Machek
de6da9255a arm: socfpga: Add watchdog disable for socfpga
This adds watchdog disable. It is neccessary for running Linux kernel.

Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>

V2: Move RSTMGR_PERMODRST_L4WD0_LSB to reset_manager.h
    Reset watchdog only if CONFIG_HW_WATCHDOG is undefined (the default)
2014-10-06 17:46:48 +02:00
Marek Vasut
be324354ee arm: socfpga: Clean up base address file
Sort the list of functional block addresses and fix indentation.
No functional change.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
Acked-by: Chin Liang See <clsee@altera.com>
2014-10-06 17:46:48 +02:00
Pavel Machek
e1f006f438 arm: socfpga: Complete the list of base addresses
Add base addresses for all subsystems as documented in the
Cyclone V HPS documentation.

Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Chin Liang See <clsee@altera.com>
2014-10-06 17:46:48 +02:00
Marek Vasut
ff7e9700ed arm: cache: Add support for write-allocate D-Cache
Add configuration for the write-allocate mode of L1 D-Cache on ARM.
This is needed for D-Cache operation on Cortex-A9 on the SoCFPGA .

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
2014-10-06 17:40:21 +02:00
Christian Gmeiner
39d0973300 imx6: add Bachmann OT1200 board
This patch adds support for the OT1200 series of devices.

Following components are used in u-boot:
+ ethernet
+ i2c
+ emmc
+ gpio

For more details see README.

Changes v1 > v2
  - make use of enable_cspi_clock(..)
  - fix usage of OUTPUT_40OHM define
  - added README

Changes v2 > v3
  - improve spelling in README
  - added own copy of mx6q_4x_mt41j128.cfg

Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
2014-10-06 17:24:28 +02:00
Masahiro Yamada
66cba041fe ARM: UniPhier: add Kconfig and defconfig
This commit allows to build Panasonic UniPhier family:
PH1-LD4, PH1-Pro4, PH1-sLD8

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-10-05 14:10:09 +09:00
Masahiro Yamada
5894ca007d ARM: UniPhier: add UniPhier SoC support code
These are used by Panasonic UniPhier SoC family.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-10-05 14:10:09 +09:00
Nitin Garg
13bc86037e imx6sx: Fix i.MX6SX HAB api function table offset
i.MX6SX ROM implements unified table sections.
The HAB function table is at offset 0x100. Update
the HAB function pointers accordingly.

Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-10-01 09:10:28 +02:00
Ye.Li
5546ad0734 usb: ehci-mx6: Rename the USB register base address
The mx6sl/mx6sx has 2 OTG and 1 host. So they have name
"USBO2H_USB_BASE_ADDR" in imx-regs.h. The driver hard codes
the USB base address name to "USBOH3", which causes the driver
failed to build for mx6sl/mx6sx.

This patch uniform the address name to "USB_BASE_ADDR" for all
mx6 series.

Signed-off-by: Ye.Li <B37916@freescale.com>
2014-09-29 10:33:27 +02:00
Ye.Li
9293d7fd50 imx: mx6: Checking PLL2 PFD0 and PFD2 for periph_clk before PFD reset
Checking the pre_periph_clk_sel and pre_periph2_clk of CCM CBCMR
register, if the PLL2 PFD0 or PLL2 PFD2 is used for the clock source,
do not reset this PFD to avoid system hang. Customers may set this
in DDR script or use BT_FREQ to select low freq boot.

Signed-off-by: Ye.Li <B37916@freescale.com>
2014-09-29 10:24:07 +02:00
Marek Vasut
7c604e98c2 arm: mxs: Wait for DRAM to start
Instead of waiting for a fixed period of time and hoping for the best
that the DRAM will start, read back an EMI status register which tells
us exactly when the DRAM started.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2014-09-29 09:02:16 +02:00
Marek Vasut
be0ecdbed5 arm: mxs: Wait when disabling VDDMEM current limiter
According to i.MX23 datasheet Table 32-17, we must wait for the supply
to settle before disabling the current limiter. Indeed, not waiting a
little here causes the system to crash at times.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2014-09-29 09:02:16 +02:00
Tom Rini
2c2277f15c Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriq 2014-09-26 09:57:52 -04:00
York Sun
c7eae7fcb1 board/ls1021aqds: Add DDR4 support
LS1021AQDS has a variant with DDR4 slot. This patch adds a new defconfig
for this variant to enable DDR4 support. RAW timing parameters are not
added for DDR4. The board timing parameters are only tuned for single-
rank 1600 and 1800MT/s with Micron DIMM 9ASF51272AZ-2G1A1 due to DIMM
availability.

Signed-off-by: York Sun <yorksun@freescale.com>
CC: Alison Wang <alison.wang@freescale.com>
2014-09-25 09:12:12 -07:00
York Sun
40f8dec54d armv8/fsl-lsch3: Release secondary cores from boot hold off with Boot Page
Secondary cores need to be released from holdoff by boot release
registers. With GPP bootrom, they can boot from main memory
directly. Individual spin table is used for each core. Spin table
and the boot page is reserved in device tree so OS won't overwrite.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Arnab Basu <arnab.basu@freescale.com>
2014-09-25 08:36:19 -07:00
York Sun
d9c68b1444 ARMv8/ls2085a_emu: Enable DP-DDR as standalone memory block
DP-DDR is used for DPAA, separated from main memory pool for general
use. It has 32-bit bus width and use a standard DDR4 DIMM (64-bit).

Signed-off-by: York Sun <yorksun@freescale.com>
2014-09-25 08:36:18 -07:00
Masahiro Yamada
783e6a72b8 kconfig: move CONFIG_OF_* to Kconfig
This commit moves:
  CONFIG_OF_CONTROL
  CONFIG_OF_SEPARATE
  CONFIG_OF_EMBED
  CONFIG_OF_HOSTFILE

Because these options are currently not supported for SPL,
the "Device Tree Control" menu does not appear in the SPL
configuration.

Note:
zynq-common.h should be adjusted so as not to change the
default value of CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
2014-09-25 09:27:50 -04:00
Masahiro Yamada
c79cba37b3 cosmetic: replace MIN, MAX with min, max
The macro MIN, MAX is defined as the aliase of min, max,
respectively.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-09-24 18:30:29 -04:00
Stefan Roese
75f698e51c arm: kirkwood: spi.h: Add some missing parenthesis
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-09-24 17:47:16 +05:30
Nitin Garg
36c1ca4d46 imx: Support i.MX6 High Assurance Boot authentication
When CONFIG_SECURE_BOOT is enabled, the signed images
like kernel and dtb can be authenticated using iMX6 CAAM.
The added command hab_auth_img can be used for HAB
authentication of images. The command takes the image
DDR location, IVT (Image Vector Table) offset inside
image as parameters. Detailed info about signing images
can be found in Freescale AppNote AN4581.

Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
2014-09-22 16:21:04 +02:00
Stefano Babic
42817eb85d Merge branch 'master' of git://git.denx.de/u-boot-arm 2014-09-22 15:51:01 +02:00
Albert ARIBAUD
2a8c9c86b9 Merge branch 'u-boot-ti/master' into 'u-boot-arm/master' 2014-09-21 16:56:44 +02:00
Bo Shen
abe307ddb8 ARM: atmel: add pcr related definition
Using CPU_HAS_PCR micro to present the SoC has pcr
(peripheral control register).

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-09-19 00:11:19 +02:00
Bo Shen
b24c1a10b5 ARM: atmel: use pcr to enable or disable peripheral clock
When use pcr (peripheral control register), then we won't need
to care about the peripheral ID.

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-09-19 00:11:18 +02:00
Bo Shen
7b1dc26fae ARM: atmel: sama5d3: add timings register
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-09-19 00:11:17 +02:00
Murali Karicheri
6c343825dd ARM: keystone: ddr3: workaround for ddr3a/3b memory issue
This patch implements a workaround to fix DDR3 memory issue.
The code for workaround detects PGSR0 errors and then preps for
and executes a software-controlled hard reset.In board_early_init,
where logic has been added to identify whether or not the previous
reset was a PORz. PLL initialization is skipped in the case of a
software-controlled hard reset.

Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Keegan Garcia <kgarcia@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-09-17 21:06:56 -04:00
Tom Rini
e38b15b061 Merge branch 'master' of git://git.denx.de/u-boot-arm 2014-09-17 18:01:04 -04:00
Albert ARIBAUD
c292adae17 Merge branch 'u-boot-imx/master' into 'u-boot-arm/master' 2014-09-17 23:35:34 +02:00
Tom Rini
1ee30aeed4 Revert "ARM: SPL: do not set gd again"
At the high level, the problem is that we set gd multiple times (and
still do, even after the commit we're reverting).  We set important
parts of gd to the copy which is not above stack but rather in the data
section.  For the release, we're going to revert this change and for the
next release we shall correct things to only, really, set gd once to an
appropriate location and ensure that comments about it are correct too.

This reverts commit f0c3a6c4ad.

Acked-by: Albert Aribaud <albert.u.boot@aribaud.net>
Signed-off-by: Tom Rini <trini@ti.com>
2014-09-16 12:24:00 -04:00
Masahiro Yamada
016a954ee9 kconfig: armv8: move CONFIG_ARM64 to Kconfig
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-09-16 12:24:00 -04:00
Masahiro Yamada
8813fdaf4b vexpress64: kconfig: consolidate CONFIG_TARGET_VEXPRESS_AEMV8A_SEMI
We do not have to distinguish CONFIG_TARGET_VEXPRESS_AEMV8A_SEMI
from CONFIG_TARGET_VEXPRESS_AEMV8A.  Rename the former to the latter.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Steve Rae <srae@broadcom.com>
Cc: David Feng <fenghua@phytium.com.cn>
2014-09-16 12:24:00 -04:00
Stefano Babic
d4940fc521 Merge branch 'master' of git://git.denx.de/u-boot-arm 2014-09-16 16:30:11 +02:00
Andrew Ruder
816264fc66 arm: mx35: use common timer functions
This patch moves mx35 to the common timer functions added in commit

  8dfafdd - Introduce common timer functions <Rob Herring>

The (removed) mx35 timer code (specifically __udelay()) could deadlock at
the 32-bit boundary of get_ticks().  get_ticks() returned a 32-bit value
cast up to a 64-bit value.  If get_ticks() + tmo in __udelay() crossed
the 32-bit boundary, the while condition became unconditionally true and
locks the processor.  Rather than patch the specific mx35 issues, simply
move everything over to the common code.

Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2014-09-16 12:53:09 +02:00
Andrew Ruder
93a0ea501e arm: mx31: use common timer functions
This patch moves mx31 to the common timer functions added in commit

  8dfafdd - Introduce common timer functions <Rob Herring>

The (removed) mx31 timer code (specifically __udelay()) could deadlock at
the 32-bit boundary of get_ticks().  get_ticks() returned a 32-bit value
cast up to a 64-bit value.  If get_ticks() + tmo in __udelay() crossed
the 32-bit boundary, the while condition became unconditionally true and
locks the processor.  Rather than patch the specific mx31 issues, simply
move everything over to the common code.

Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Helmut Raiger <helmut.raiger@hale.at>
2014-09-16 12:51:46 +02:00
Masahiro Yamada
461be2f96e kconfig: remove redundant "string" type in arch and board Kconfigs
Now the types of CONFIG_SYS_{ARCH, CPU, SOC, VENDOR, BOARD, CONFIG_NAME}
are specified in arch/Kconfig.

We can delete the ones in arch and board Kconfig files.

This commit can be easily reproduced by the following command:

find . -name Kconfig -a ! -path ./arch/Kconfig | xargs sed -i -e '
/config[[:space:]]SYS_\(ARCH\|CPU\|SOC\|\VENDOR\|BOARD\|CONFIG_NAME\)/ {
    N
    s/\n[[:space:]]*string//
}
'

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-09-13 16:43:55 -04:00
Tom Rini
8d028d404f Merge branch 'master' of git://git.denx.de/u-boot-dm 2014-09-13 16:32:52 -04:00
Tom Rini
114cc4290b Merge branch 'master' of git://git.denx.de/u-boot-arm 2014-09-12 11:27:46 -04:00
Benoît Thébaudeau
a7f99bf139 arm: Fix _start for CONFIG_SYS_DV_NOR_BOOT_CFG
The boards using CONFIG_SYS_DV_NOR_BOOT_CFG (i.e. calimain,
da850evm_direct_nor and enbw_cmc) had the _start symbol defined after
the CONFIG_SYS_DV_NOR_BOOT_CFG word rather than before it in
arch/arm/lib/vectors.S. Because of that, if by lack of luck
'gd->mon_len = (ulong)&__bss_end - (ulong)_start' (see setup_mon_len())
was a multiple of 4 kiB (see reserve_uboot()), then the last BSS word
overlapped the first word of the following reserved RAM area (or went
beyond the top of RAM without such an area) after relocation because
__image_copy_start did not match _start (see relocate_code()).

This was broken by commit 41623c9 'arm: move exception handling out of
start.S files', which defined _start twice (before and after the
CONFIG_SYS_DV_NOR_BOOT_CFG word), then by commit 0a26e1d 'arm: fix a
double-definition error of _start symbol', which kept the definition of
the _start symbol after the CONFIG_SYS_DV_NOR_BOOT_CFG word. This new
commit fixes this issue by restoring the original behavior, i.e. by
defining the _start symbol before the CONFIG_SYS_DV_NOR_BOOT_CFG word.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Manfred Rudigier <manfred.rudigier@omicron.at>
Cc: Christian Riesch <christian.riesch@omicron.at>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: Heiko Schocher <hs@denx.de>
2014-09-11 18:04:39 +02:00
Benoît Thébaudeau
58f9e1ae63 arm: Make reset position-independent
Some boards, like mx31pdk and tx25, require the beginning of the SPL
code to be position-independent. For these two boards, this is because
they use the i.MX external NAND boot, which starts by executing the
first NAND Flash page from the NFC page buffer. The SPL then needs to
copy itself to its actual link address in order to free the NFC page
buffer and use it to load the non-SPL image from Flash before running
it. This means that the SPL runtime address differs from its link
address between the reset and the initial copy performed by
board_init_f(), so this part of the SPL binary must be
position-independent.

This requirement was broken by commit 41623c9 'arm: move exception
handling out of start.S files', which used an absolute address to branch
to the reset routine. This new commit restores the original behavior,
which just performed a relative branch. This fixes the boot of mx31pdk
and tx25.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
Reported-by: Helmut Raiger <helmut.raiger@hale.at>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Magnus Lilja <lilja.magnus@gmail.com>
Cc: John Rigby <jcrigby@gmail.com>
Tested-by: Magnus Lilja <lilja.magnus@gmail.com>
2014-09-11 18:04:34 +02:00
Stefano Babic
3d8f1798ba imx: Fix build of mx6sxsabresd
Commit 224beb833e add clock
enabling function for FEC, but the masks are not available
for SX processor and the mx6sxsabresd cannot be built clean.

Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
CC: Nikita Kiryanov <nikita@compulab.co.il>
2014-09-11 10:13:44 +02:00
Simon Glass
c369139234 tegra: dts: Add serial port details
Some Tegra device tree files do not include information about the serial
ports. Add this and also add information about the input clock speed.

The console alias needs to be set up to indicate which port is used for
the console.

Also add a binding file since this is missing.

Series-changes; 5
- Add full serial port nodes from Linux tree (commit fc9d4dbe)
- Use /chosen/stdout-path instead of /aliases/console to specify the console

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-09-10 13:00:02 -06:00
Simon Glass
2fccd2d96b tegra: Convert tegra GPIO driver to use driver model
This is an implementation of GPIOs for Tegra that uses driver model. It has
been tested on trimslice and also using the new iotrace feature.

The implementation uses a top-level GPIO device (which has no actual GPIOS).
Under this all the banks are created as separate GPIO devices.

The GPIOs are named as per the Tegra datasheet/header files: A0..A7, B0..B7,
..., Z0..Z7, AA0..AA7, etc.

Since driver model is not yet available before relocation, or in SPL, a
special function is provided for seaboard's SPL code.

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-09-10 12:59:59 -06:00
Fabio Estevam
1b8ad74a6f pcie_imx: Add mx6solox support
Let PCI on mx6solox also be supported.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
2014-09-09 17:24:49 +02:00
Fabio Estevam
ac17dcf653 mx6: imx-regs: Provide a structure for GPC registers
Introduce a structure for accessing the General Power Controller block (GPC)
registers.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-09-09 17:24:49 +02:00
Fabio Estevam
19a895cbe9 mx6qsabreauto: Remove imx6q-sabreauto.dts
Commit fa9c021632 ("mx6: add example DTB for mx6qsabreauto") introduced
'imx6q-sabreauto.dts' but it adds no real value as the dts file only contains
the 'model' and 'compatible' strings.

After this commit the final binary is also changed from 'u-boot.imx' to
'u-boot-dtb.imx', which may confuse users.

So revert it until a more complete and useful device tree could be provided.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
2014-09-09 17:11:01 +02:00
Nikolay Dimitrov
2d59e3ecd2 mx6: Fix ECSPI typo in soc_boot_modes
Signed-off-by: Nikolay Dimitrov <picmaster@mail.bg>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
2014-09-09 16:47:43 +02:00
Ye.Li
4aa7ac30a7 iMX6: Disable the L2 before chaning the PL310 latency
The Latency parameters of PL310 Tag RAM latency control register and
Data RAM Latency control register are set in L2 cache enable. And
setting these registers must have PL310 NOT enabled.

But when using Plugin mode boot, the PL310 is enabled by bootrom.
The patch disables the PL310 before applying this setting.

Signed-off-by: Ye.Li <Ye.Li@freescale.com>
2014-09-09 16:30:40 +02:00
Nikita Kiryanov
e32028a70b arm: mx6: add support for Compulab cm-fx6 CoM
Add initial support for Compulab CM-FX6 CoM.
Support includes MMC, SPI flash, and SPL with dynamic DRAM detection.

Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
2014-09-09 15:35:43 +02:00
Nikita Kiryanov
ea818ae748 arm: mx6: add get_cpu_type()
Define get_cpu_type(). Reuse it in is_cpu_type().

Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
2014-09-09 15:35:00 +02:00
Nikita Kiryanov
07ee927d2c arm: mx6: ddr: fix cs0_end calculation
Current way of calculation CS0_END field for MMDCx_MDASP register
is problematic because in most cases the user is forced to define
cs_density in an unnatural way: as value - 2, instead of value.

This breaks the abstraction provided by struct mx6_ddr_sysinfo
because the user is forced to be aware of the way the calculation
is performed.

Refactor the calculation.

Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
2014-09-09 15:35:00 +02:00
Nikita Kiryanov
08155289a4 arm: mx6: ddr: configure MMDC for slow_pd
According to MX6 TRM, both MMDC and DRAM should be configured to
the same powerdown precharge. Currently, mx6_dram_cfg()
configures MMDC for fast pd (MDPDC[7] = 0), and the DRAM for
'slow exit (DLL off)' (MR0[12] = 0).

Configure MMDC for slow pd.

Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Tim Harvey <tharvey@gateworks.com>
2014-09-09 15:35:00 +02:00
Nikita Kiryanov
06a51b8cc8 arm: mx6: ddr: do not write into reserved bit
Bit 16 in mapsr register is in a reserved field. Don't write to it.

Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
2014-09-09 15:35:00 +02:00
Nikita Kiryanov
3368918f71 arm: mx6: ddr: cleanup
No functional changes.

Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
2014-09-09 15:33:39 +02:00
Nikita Kiryanov
c6c2492ad8 i2c: imx: add macros to setup pads for multiple SoC types
Add macro which defines i2c_pads_info structs for multiple SoC types,
and a macro which selects the appropriate struct based on CPU type,
thus eliminating the need to manage multiple i2c pad configurations
manually when supporting multiple SoC types.

Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
2014-09-09 15:32:32 +02:00
Nikita Kiryanov
224beb833e mx6: add clock enabling functions
Add functions to enable/disable clocks for UART, SPI, ENET, and MMC.

Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
2014-09-09 15:32:32 +02:00
Jeroen Hofstee
f2cbb037a7 eabi_compat: add __aeabi_memcpy __aeabi_memset
cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-09-09 13:51:11 +02:00
Jeroen Hofstee
c65a2abb6c ARM: make gd a function for clang
"clang does not support global register variables; this is
unlikely to be implemented soon because it requires additional
LLVM backend support" [1]

Workaround it by obtaining the value of gd/r9 by an inline
asm routine. Note there is no set routine added for ARM at the
moment, since most if not all updates of gd from c are actually
not needed for ARM.

[1] http://clang.llvm.org/docs/UsersManual.html

cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-09-09 13:51:08 +02:00
Jeroen Hofstee
f0c3a6c4ad ARM: SPL: do not set gd again
Just before calling board_init_f, crt0.S has already
reserved space for the initial gd on the stack. There
should be no need to allocate it again.

cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-09-09 13:50:57 +02:00
Albert ARIBAUD
b653516769 Merge branch 'u-boot-samsung/master' into 'u-boot-arm/master' 2014-09-09 00:21:24 +02:00
Wang Huan
327def5060 video: dcu: Add DCU driver support
This patch is to add DCU driver support. DCU also named
2D-ACE(Two Dimensional Animation and Compositing Engine)
is a system master that fetches graphics stored in internal
or external memory and displays them on a TFT LCD panel.

Signed-off-by: Alison Wang <alison.wang@freescale.com>
2014-09-08 10:30:35 -07:00
Wang Huan
c8a7d9dab0 arm: ls102xa: Add basic support for LS1021ATWR board
LS102xA is an ARMv7 implementation. This patch is to add
basic support for LS1021ATWR board.
 One DDR controller
 DUART1 is used as the console

For the detail board information, please refer to README.

Signed-off-by: Chen Lu <chen.lu@freescale.com>
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
2014-09-08 10:30:35 -07:00
Wang Huan
550e3dc090 arm: ls102xa: Add basic support for LS1021AQDS board
LS102xA is an ARMv7 implementation. This patch is to add
basic support for LS1021AQDS board.
 One DDR controller
 DUART1 is used as the console

For the detail board information, please refer to README.

Signed-off-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: Jason Jin <jason.jin@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
2014-09-08 10:30:34 -07:00
Wang Huan
d60a2099a2 arm: ls102xa: Add Freescale LS102xA SoC support
The QorIQ LS1 family is built on Layerscape architecture,
the industry's first software-aware, core-agnostic networking
architecture to offer unprecedented efficiency and scale.

Freescale LS102xA is a set of SoCs combines two ARM
Cortex-A7 cores that have been optimized for high
reliability and pack the highest level of integration
available for sub-3 W embedded communications processors
with Layerscape architecture and with a comprehensive
enablement model focused on ease of programmability.

Signed-off-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: Jason Jin <jason.jin@freescale.com>
Signed-off-by: Jingchang Lu <jingchang.lu@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
2014-09-08 10:30:32 -07:00
Ajay Kumar
466d40396e ARM: exynos: peach_pit: Add DT nodes for fimd and parade bridge chip
This patch adds DT properties for fimd and the parade bridge chip
present on peach_pit. The panel supports 1366x768 resolution.

Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-09-05 20:37:07 +09:00
Ajay Kumar
a99cea0313 exynos5420: add callbacks needed for exynos_fb driver
Add initialization code for peach_pit panel, parade bridge chip,
and backlight.

Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-09-05 20:37:07 +09:00
Ajay Kumar
2358fc8ed9 ARM: exynos: Add missing declaration for gpio_direction_input
This patch adds missing declaration for gpio_direction_input
function, thereby helps in resolving compilation warnings.

Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-09-05 20:37:07 +09:00
Ajay Kumar
45c480c9f6 video: exynos_fimd: Add framework to disable FIMD sysmmu
On Exynos5420 and newer versions, the FIMD sysmmus are in
"on state" by default.
We have to disable them in order to make FIMD DMA work.
This patch adds the required framework to exynos_fimd driver,
and disables FIMD sysmmu on Exynos5420.

Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-09-05 20:37:07 +09:00
Ajay Kumar
496f0e47e1 arm: exynos: Add get_lcd_clk and set_lcd_clk callbacks for Exynos5420
Add get_lcd_clk and set_lcd_clk callbacks for Exynos5420 needed by
exynos video driver.
Also, configure ACLK_400_DISP1 as the parent for MUX_ACLK_400_DISP1_SUB_SEL.

Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-09-05 20:37:07 +09:00
Ajay Kumar
e6756f6a2e arm: exynos: Add RPLL for Exynos5420
RPLL is needed to drive the LCD panel on Exynos5420 based boards.

Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-09-05 20:37:07 +09:00
Ajay Kumar
f0017175e3 exynos_fb: Remove usage of static defines
Previously, we used to statically assign values for vl_col, vl_row and
vl_bpix using #defines like LCD_XRES, LCD_YRES and LCD_COLOR16.

Introducing the function exynos_lcd_early_init() would take care of this
assignment on the fly by parsing FIMD DT properties, thereby allowing us
to remove LCD_XRES and LCD_YRES from the main config file.

Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-09-05 20:37:07 +09:00
Przemyslaw Marczak
73eca21128 odroid: kconfig: add odroid_defconfig
This config is valid for two devices:
- Odroid X2,
- Odroid U3.

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-09-05 13:58:50 +09:00
Przemyslaw Marczak
a47fa7906c odroid: add odroid U3/X2 device tree description
This is a standard description for Odroid boards.

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-09-05 13:58:50 +09:00
Przemyslaw Marczak
1fb4dab2a1 arm:reset: call the reset_misc() before the cpu reset
On an Odroid U3 board, the SOC is unable to reset the eMMC card
in the DWMMC mode by the cpu software reset. Manual reset of the card
by switching proper gpio pin - fixes this issue.

Such solution needs to add a call to pre reset function.
This is done by the reset_misc() function, which is called before reset_cpu().
The function reset_misc() is a weak function.

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>

Changes v4:
- arch/arm/reset: fix weak function attribute to proper style
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-09-05 13:58:49 +09:00
Przemyslaw Marczak
4fb4d55a35 arch:exynos: boot mode: add get_boot_mode(), code cleanup
This patch introduces code clean-up for exynos boot mode check.
It includes:
- removal of typedef: boot_mode
- move the boot mode enum to arch-exynos/power.h
- add bootmode for sequence: eMMC 4.4 ch4 / SD ch2
- add new function: get_boot_mode() for OM[5:1] pin check
- update spl boot code

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>

Changes v5:
- exynos: boot mode: add missing bootmode (1st:EMMC 4.4 / 2nd:SD ch2)

Changes v6:
- none

changes v7:
- change boot mode name: BOOT_MODE_MMC to BOOT_MODE_SD
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-09-05 13:58:49 +09:00
Przemyslaw Marczak
19f1b629bf exynos: pinmux: fix the gpio names for exynos4x12 mmc
This change fixes the bad gpio configuration for the exynos dwmmc.

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Beomho Seo <beomho.seo@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-09-05 13:58:49 +09:00
R Sricharan
681f785f7c ARM: DRA72: DDR3: Add emif settings for 666MHz clock
On DRA72x, EMIF supports DDR3 upto 667MHz.
Adding the required settings for DDR3 at 666MHz and enabling it.

Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2014-09-04 13:12:49 -04:00
Khoronzhuk, Ivan
e6c9428a2f keystone2: use readl/writel functions instead of redefinition
There is no reason to redefine pure readl/writel functions.
So remove this redundancy.

Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Acked-by: Vitaly Andrianov <vitalya@ti.com>
2014-09-04 13:06:00 -04:00
Khoronzhuk, Ivan
1c4044ae4a ARM: keystone: clock: use correct BWADJ field mask for PASSPLLCTL0
The mask for BWADJ field of PASSPLLCTL0 register has to be 0xff, but
by mistake, here is used shift instead of mask, so correct it.

Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-09-04 13:05:57 -04:00
Masahiro Yamada
a1263632bb mx6: tqma6: get board support back to Kconfig build system
The QS Systems TQMa6 board support was added by commit cb07d74e
and lost by commit e82abaeb.

Commit e82abaeb merged the IMX branch based on pre-Kconfig
and the mainline based on post-Kconfig, simply deleting
the boards.cfg file.  As a result, some boards added just before
the merge were lost.

This commit adds Kconfig, defconfig, MAINTAINERS for TQMa6 board
to work on the Kconfig infrastructure.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Markus Niebel <Markus.Niebel@tq-group.com>
Cc: Stefano Babic <sbabic@denx.de>
2014-08-31 12:01:04 -04:00
Masahiro Yamada
16e16fdde2 nomadik: kconfig: move board select menu and common settings
Becuase the board select menu in arch/arm/Kconfig is too big,
move the Nomadik board select menu to nomadik/Kconfig.

Move also common settings (CONFIG_SYS_CPU="arm926ejs" and
CONFIG_SYS_SOC="nomadik").

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-08-30 21:22:00 -04:00
Masahiro Yamada
ef2b694c73 highbank: kconfig: move common settings
Move Highbank-specific settings to highbank/Kconfig.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Rob Herring <robh@kernel.org>
2014-08-30 21:22:00 -04:00
Masahiro Yamada
22f2be7a12 orion5x: kconfig: move board select menu and common settings
Becuase the board select menu in arch/arm/Kconfig is too big,
move the Orion5x board select menu to orion5x/Kconfig.

Move also common settings (CONFIG_SYS_CPU="arm926ejs" and
CONFIG_SYS_SOC="orion5x").

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
2014-08-30 21:21:59 -04:00
Masahiro Yamada
c338f09e96 keystone: kconfig: move board select menu and common settings
Becuase the board select menu in arch/arm/Kconfig is too big,
move the Keystone board select menu to keystone/Kconfig.

Move also common settings (CONFIG_SYS_CPU="armv7" and
CONFIG_SYS_SOC="keystone").

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Tom Rini <trini@ti.com>
Cc: Vitaly Andrianov <vitalya@ti.com>
2014-08-30 21:21:59 -04:00
Masahiro Yamada
6c5431ac81 omap5: kconfig: move board select menu and common settings
Becuase the board select menu in arch/arm/Kconfig is too big,
move the OMAP5 board select menu to omap5/Kconfig.

Move also common settings (CONFIG_SYS_CPU="armv7" and
CONFIG_SYS_SOC="omap5").

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Tom Rini <trini@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
2014-08-30 21:21:59 -04:00
Masahiro Yamada
d08215a5f1 omap4: kconfig: move board select menu and common settings
Becuase the board select menu in arch/arm/Kconfig is too big,
move the OMAP4 board select menu to omap4/Kconfig.

Move also common settings (CONFIG_SYS_CPU="armv7" and
CONFIG_SYS_SOC="omap4").

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Tom Rini <trini@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
2014-08-30 21:21:59 -04:00
Masahiro Yamada
3cfbcb58d3 omap3: kconfig: move board select menu and common settings
Becuase the board select menu in arch/arm/Kconfig is too big,
move the OMAP3 board select menu to omap3/Kconfig.

Move also common settings (CONFIG_SYS_CPU="armv7" and
CONFIG_SYS_SOC="omap3

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Tom Rini <trini@ti.com>
2014-08-30 21:21:59 -04:00
Masahiro Yamada
3491ba6311 davinci: kconfig: move board select menu and common settings
Becuase the board select menu in arch/arm/Kconfig is too big,
move the Davinci board select menu to davinci/Kconfig.

Move also common settings (CONFIG_SYS_CPU="arm926ejs" and
CONFIG_SYS_SOC="davinci").

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Tom Rini <trini@ti.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
2014-08-30 21:21:59 -04:00
Masahiro Yamada
72df68cc6b exynos: kconfig: move board select menu and common settings
Becuase the board select menu in arch/arm/Kconfig is too big,
move the Exynos board select menu to exynos/Kconfig.

Consolidate also common settings (CONFIG_SYS_CPU="armv7" and
CONFIG_SYS_SOC="exynos").

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
2014-08-30 21:21:59 -04:00
Masahiro Yamada
47539e2317 kirkwood: kconfig: refactor Kconfig and defconfig
Becuase the board select menu in arch/arm/Kconfig is too big,
move the KirkWood board select menu to kirkwood/Kconfig.

Consolidate also common settings (CONFIG_SYS_CPU="arm926ejs" and
CONFIG_SYS_SOC="kirkwood").

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Prafulla Wadasdkar <prafulla@marvell.com>
Cc: Luka Perkov <luka@openwrt.org>
2014-08-30 21:21:21 -04:00
Masahiro Yamada
ad17a81c06 versatile: kconfig: move common settings
Move Versatile-specific settings to versatile/Kconfig.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-08-30 21:19:32 -04:00
Masahiro Yamada
f40b989863 rmobile: kconfig: move board select menu and common settings
Becuase the board select menu in arch/arm/Kconfig is too big,
move the Rmobile board select menu to rmobile/Kconfig.

Consolidate also common settings (CONFIG_SYS_CPU="armv7" and
CONFIG_SYS_SOC="rmobile").

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2014-08-30 21:19:32 -04:00
Masahiro Yamada
ddd960e6c4 tegra: kconfig: move board select menu and common settings
Becuase the board select menu in arch/arm/Kconfig is too big,
move the Tegra board select menu to tegra/Kconfig.

Insert the Tegra SoC select menu between the arch select and the
board select.

 Architecture select
 |-- Tegra Platform (Tegra)
     |- Tegra SoC select (Tegra20 / 30 / 114 / 124)
        |- Board select

Consolidate also common settings (CONFIG_SYS_CPU="armv7" and
CONFIG_SYS_SOC="tegra*") and always "select" CONFIG_SPL as follows:

  config TEGRA
          bool
          select SPL

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Cc: Tom Warren <twarren@nvidia.com>
2014-08-30 21:19:32 -04:00
Masahiro Yamada
44dcb4036b zynq: kconfig: move board select menu and common settings
Becuase the board select menu in arch/arm/Kconfig is too big,
move the Zynq board select menu to zynq/Kconfig.

Consolidate also common settings (CONFIG_SYS_CPU="armv7" and
CONFIG_SYS_SOC="zynq").

Refactor board/xilinx/zynq/MAINTAINERS too.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
2014-08-30 21:19:32 -04:00
Benoît Thébaudeau
eeadd3fe0f arm: Add missing .vectors section to linker scripts
Commit 41623c9 'arm: move exception handling out of start.S files' missed some
linker scripts. Hence, some boards no longer had exception handling linked since
this commit. Restore the original behavior by adding the .vectors section to
these linker scripts.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
2014-08-30 07:46:41 -04:00
Tom Rini
3f1b6bebe0 arm64: Correct passing of Linux kernel args
The Documentation/arm64/booting.txt document says that pass in x1/x2/x3
as 0 as they are reserved for future use.

Signed-off-by: Tom Rini <trini@ti.com>
2014-08-30 07:46:40 -04:00
Steve Rae
9dec5270be arm: convert Cygnus and NSP boards to Kconfig
Convert the bcm958300k and the bcm958622hr boards from "boards.cfg" to Kconfig.

Signed-off-by: Steve Rae <srae@broadcom.com>
2014-08-30 07:46:40 -04:00
Scott Branden
da1f5ac295 arm: add Cygnus and NSP boards
The bcm_ep board configuration is used by a number of boards
including Cygnus and NSP.
Add builds for the bcm958300k and the bcm958622hr boards.

Signed-off-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Steve Rae <srae@broadcom.com>
2014-08-30 07:46:40 -04:00
Scott Branden
562f01a2ba arm: bcmnsp: Add bcmnsp u-architecture
Base support for the Broadcom NSP SoC.
Based on iproc-common and the SoC specific reset function.

Signed-off-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Steve Rae <srae@broadcom.com>
2014-08-30 07:46:40 -04:00
Scott Branden
7986688075 arm: bcmcygnus: Add bcmcygnus u-architecture
Base support for the Broadcom Cygnus SoC.
Based on iproc-common and the SoC specific reset function.

Signed-off-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Steve Rae <srae@broadcom.com>
2014-08-30 07:46:40 -04:00
Scott Branden
c4b4500910 arm: iproc: Initial commit of iproc architecture code
The iproc architecture code is present in several Broadcom
chip architectures, including Cygnus and NSP.

Signed-off-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Steve Rae <srae@broadcom.com>
2014-08-30 07:46:40 -04:00
Stefan Agner
b0e31c7b66 arm: vf610: add NFC clock support
Add NFC (NAND Flash Controller) clock support and enable them
at board initialization time.

Signed-off-by: Stefan Agner <stefan@agner.ch>
2014-08-30 07:46:40 -04:00
Stefan Agner
baa3134440 arm: vf610: add NFC pin mux
Add pin mux for NAND Flash Controller (NFC). NAND can be connected
using 8 or 16 data lines, this patch adds pin mux entries for all
16 data lines.

Signed-off-by: Stefan Agner <stefan@agner.ch>
2014-08-30 07:46:39 -04:00
Marek Vasut
221a49d5bd ARM: Fix overflow in MMU setup
The patch fixes a corner case where adding size to DRAM start resulted
in a value (1 << 32), which in turn overflew the u32 computation, which
resulted in 0 and it therefore prevented correct setup of the MMU tables.

The addition of DRAM bank start and it's size can end up right at the end
of the address space in the special case of a machine with enough memory.
To prevent this overflow, shift the start and size separately and add them
only after they were shifted.

Hopefully, we only have systems in tree which have DRAM size aligned to
1MiB boundary. If not, this patch would break such systems. On the other
hand, such system would be broken by design anyway.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
2014-08-30 07:46:39 -04:00
Jiandong Zheng
2d66a0fd58 arm: bcm281xx: Add Ethernet Clock support
Enable Ethernet clock when Broadcom StarFighter2 Ethernet block
(CONFIG_BCM_SF2_ETH) is enabled.

Signed-off-by: Jiandong Zheng <jdzheng@broadcom.com>
Signed-off-by: Steve Rae <srae@broadcom.com>
2014-08-30 07:46:39 -04:00
Sergey Kostanbaev
0bf62d7bc4 arm: ep9315: Add .vectors section to lds and remove obsolete lds
However ep9315 don't use
interrupt vectors during startup, but _startup symbol is used inside uboot to
calculate actual monitor size.

Signed-off-by: Sergey Kostanbaev <sergey.kostanbaev@gmail.com>
Cc: albert.u.boot@aribaud.net
2014-08-30 07:46:38 -04:00
Pavel Machek
99b97106f3 socfpga: initialize designware ethernet
Enable initialization fo designware ethernet controller. With this
patch, ethernet works in my configuration, provided I set ethernet
address in the environment.

Signed-off-by: Pavel Machek <pavel@denx.de>
2014-08-30 07:46:38 -04:00
Chin Liang See
3ab019e1dc socfpga: Fix SOCFPGA build error for Altera dev kit
To fix the build error when build for Altera dev kit, not
virtual target. At same time, set the build for Altera dev
kit as default instead virtual target. With that, U-Boot
is booting well and SPL still lack of few drivers.

Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
2014-08-29 15:50:54 -04:00
Pavel Machek
51fb455f82 socfpga: fix clock manager register definition
Structure defining clock manager hardware was wrong, leading to
wrong registers being accessed and hang in MMC init.

This fixes structure to match hardware.

Signed-off-by: Pavel Machek <pavel@denx.de>
2014-08-29 15:50:50 -04:00
Christian Riesch
db993fc8ec arm: include config.h in arch/arm/lib/vectors.S
config.h is required for CONFIG_SYS_DV_NOR_BOOT_CFG.

Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Reported-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
2014-08-29 15:50:43 -04:00
Jeroen Hofstee
8863aa5c98 ARM:asm:io.h use static inline
When compiling u-boot with W=1 the extern inline void for
read* is likely causing the most noise. gcc / clang will
warn there is never a actual declaration for these functions.
Instead of declaring these extern make them static inline so
it is actually declared.

cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-08-29 15:50:43 -04:00
Tom Rini
6defdc0b55 Merge branch 'master' of git://git.denx.de/u-boot-ti 2014-08-29 13:47:42 -04:00
Tom Rini
7f14fb20f8 Merge branch 'zynq' of git://www.denx.de/git/u-boot-microblaze 2014-08-29 11:07:35 -04:00
Tom Rini
5ddc329341 Merge branch 'master' of git://git.denx.de/u-boot-tegra 2014-08-29 11:07:10 -04:00
Tom Rini
5a1095a830 Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2014-08-29 11:06:51 -04:00
Tom Rini
6af857c50d Merge branch 'master' of http://git.denx.de/u-boot-sunxi 2014-08-29 11:06:26 -04:00
Tom Rini
3e1b36bd58 Merge branch 'master' of git://git.denx.de/u-boot-arm 2014-08-28 13:03:25 -04:00
Lokesh Vutla
7b92252370 ARM: DRA: Enable VTT regulator
DRA7 evm REV G and later boards uses a vtt regulator for DDR3 termination
and this is controlled by gpio7_11. Configuring gpio7_11.
The pad A22(offset 0x3b4) is used by gpio7_11 on REV G and later boards,
and left unused on previous boards, so it is safe enough to enable gpio
on all DRA7 boards.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2014-08-25 10:48:13 -04:00
Sricharan R
f2a1b93b5c ARM: DRA7: Enable software leveling for dra7
Currently hw leveling is enabled by default on DRA7/72.
But the hardware team suggested to use sw leveling as hw leveling
is not characterized and seen some test case failures.
So enabling sw leveling on all DRA7 platforms.

Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2014-08-25 10:48:13 -04:00
Vitaly Andrianov
61f66fd5a8 keystone2: use EFUSE_BOOTROM information to configure PLLs
This patch reads EFUSE_BOOTROM register to see the maximum supported
clock for CORE and TETRIS PLLs and configure them accordingly.

Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-08-25 10:48:12 -04:00
pekon gupta
9352697aa0 board/ti/dra7xx: add support for parallel NOR
This patch adds support for parallel NOR device (S29GL512S10) present on J6-EVM.
The Flash device is connected to GPMC controller on chip-select[0] and accessed
as memory-mapped device. It has data-witdh=x16, capacity-64MBytes(512Mbits) and
is CFI compatible.

As multiple devices are share GPMC pins on this board, so following board
settings are required to detect NOR device:
     SW5.1 (NAND_BOOTn) = OFF (logic-1)
     SW5.2 (NOR_BOOTn)  = ON  (logic-0) /* Active-low */
     SW5.3 (eMMC_BOOTn) = OFF (logic-1)
     SW5.4 (QSPI_BOOTn) = OFF (logic-1)

And also set appropriate SYSBOOT configurations:
     SW3.1 (SYSBOOT[ 8])= ON  (logic-1) /* selects SYS_CLK1 speed */
     SW3.2 (SYSBOOT[ 9])= OFF (logic-0) /* selects SYS_CLK1 speed */
     SW3.3 (SYSBOOT[10])= ON  (logic-1) /* wait-pin monitoring = enabled */
     SW3.4 (SYSBOOT[11])= OFF (logic-0) /* device type: Non Muxed */
     SW3.5 (SYSBOOT[12])= OFF (logic-0) /* device type: Non Muxed */
     SW3.6 (SYSBOOT[13])= ON  (logic-1) /* device bus-width: 1(x16) */
     SW3.7 (SYSBOOT[14])= OFF (logic-0) /* reserved */
     SW3.8 (SYSBOOT[15])= ON  (logic-1) /* reserved */

Also, following changes are required to enable NOR Flash support in
dra7xx_evm board profile:
2014-08-25 10:48:12 -04:00
Masahiro Yamada
62d636aa2a omap: remove omap5912osk board support
Emails to the board maintainer
"Rishi Bhattacharya <rishi@ti.com>"
have been bouncing.

Tom suggested to remove this board.

Remove also omap1510_udc.c because this is the last board
to enable it.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Suggested-by: Tom Rini <trini@ti.com>
2014-08-21 12:01:12 -04:00
Fabio Estevam
d145878d59 mx6sxsabresd: Add Ethernet support
mx6sxsabresd board has 2 FEC ports, each one connected to a AR8031.

Add support for one FEC port initially.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-08-20 13:15:23 +02:00
Fabio Estevam
5c045cddaa mx6sx: Adjust enable_fec_anatop_clock() for mx6solox
Configure and enable the ethernet clock for mx6solox.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-08-20 13:14:09 +02:00
Fabio Estevam
080d72f233 mx6sxsabresd: Convert to the new Kconfig style
mx6sxsabresd was not in the master branch when the conversion to the new Kconfig
style happened, so convert it now so that it can build again.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-08-20 13:11:12 +02:00
Marek Vasut
b299ab7435 ARM: mx6: Handle the MMDCx_MDCTL COL field caprices
The COL field value cannot be easily calculated from the desired
column number. Instead, there are special cases for that, see the
datasheet, MMDCx_MDCTL field description, field COL . Cater for
those special cases.

Signed-off-by: Marek Vasut <marex@denx.de>
2014-08-20 12:22:52 +02:00
Marek Vasut
fcfdfdd58c ARM: mx6: Prevent overflow in DRAM size detection
The MX6 DRAM controller can be configured to handle 4GiB of DRAM, but
only 3840 MiB of that can be really used. In case the controller is
configured to operate a 4GiB module, the imx_ddr_size() function will
correctly compute that there is 4GiB of DRAM in the system. Firstly,
the return value is 32-bit, so the function will effectively return
zero. Secondly, the MX6 cannot address the full 4GiB, but only 3840MiB
of all that. Thus, clamp the returned size to 3840MiB in such case.

Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Tim Harvey <tharvey@gateworks.com>
2014-08-20 12:21:57 +02:00
Marek Vasut
68968901e7 ARM: mx5: Fix CHSCCDR name
Fix the name of the CCM CHSCCDR register.

Signed-off-by: Marek Vasut <marex@denx.de>
2014-08-20 12:19:20 +02:00
Gabriel Huau
a76df70908 mx6: add support of multi-processor command
This allows u-boot to load different OS or Bare Metal application on
different cores of the i.MX6 SoC.
For example: running Android on cpu0 and a RT OS like QNX/FreeRTOS on cpu1.

Signed-off-by: Gabriel Huau <contact@huau-gabriel.fr>
Acked-by: Stefano Babic <sbabic@denx.de>
2014-08-20 11:52:54 +02:00
Michal Simek
ae2ee77f98 ARM: zynq: Remove spl.h
Do not specify own zynq specific SPL macros
because there is no need for that.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-08-19 08:48:18 +02:00
Michal Simek
dbc31f6a20 ARM: zynq: Move ps7_init() out of spl.h
Prepare for spl.h removal.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-08-19 08:48:00 +02:00
Stefan Agner
24d4d422c1 ARM: tegra: add Colibri T30 board support
This adds board support for the Toradex Colibri T30 module.

Working functions:
- SD card boot
- eMMC environment and boot
- USB host/USB client (on the dual role port)
- Network (via ASIX USB)

Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-08-18 16:59:04 -07:00
Stephen Warren
aeb3fcb359 ARM: tegra: Use mem size from MC rather than ODMDATA
In at least Tegra124, the Tegra memory controller (MC) has a register
that controls the memory size. Read this to determine the memory size
rather than requiring this to be redundantly encoded into the ODMDATA.
This way, changes to the BCT (i.e. MC configuration) automatically
updated SW's view of the memory size, without requiring manual changes
to the ODMDATA.

Future work potentially required:
* Clip the memory size to architectural limits; U-Boot probably doesn't
  and won't support either LPAE or Tegra's "swiss cheese" memory layout,
  at least one of which would be required for >2GB RAM.
* Subtract out any carveout required by firmware on future SoCs.

Based-on-work-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-08-18 16:57:03 -07:00
Bryan Wu
df3443dfa4 ARM: tegra: Disable VPR
On Tegra114 and Tegra124 platforms, certain display-related registers cannot
be accessed unless the VPR registers are programmed.  For bootloader, we
probably don't care about VPR, so we disable it (which counts as programming
it, and allows those display-related registers to be accessed).

This patch is based on the commit 5f499646c83ba08079f3fdff6591f638a0ce4c0c
in Chromium OS U-Boot project.

Signed-off-by: Andrew Chew <achew@nvidia.com>
Signed-off-by: Jimmy Zhang <jimmzhang@nvidia.com>
Signed-off-by: Bryan Wu <pengw@nvidia.com>
[acourbot: ensure write went through, vpr.c style changes]
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Cc: Tom Warren <TWarren@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Terje Bergstrom <tbergstrom@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-08-18 16:57:02 -07:00
Stefano Babic
7e9291720d Update aristainetos board to Kconfig
aristainetos board was merged in u-boot-imx before
Kconfig was integrated, but it is not yet
mainline.

Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
2014-08-13 09:30:41 +02:00
Siarhei Siamashka
bf4ca384ad sunxi: dram: Autodetect DDR3 bus width and density
In the case if the 'dram_para' struct does not specify the exact bus
width or chip density, just use a trial and error method to find a
usable configuration.

Because all the major bugs in the DRAM initialization sequence are
now hopefully fixed, it should be safe to re-initialize the DRAM
controller multiple times until we get it configured right. The
original Allwinner's boot0 bootloader also used a similar
autodetection trick.

The DDR3 spec contains the package pinout and addressing table for
different possible chip densities. It appears to be impossible to
distinguish between a single chip with 16 I/O data lines and a pair
of chips with 8 I/O data lines in the case if they provide the same
storage capacity. Because a single 16-bit chip has a higher density
than a pair of equivalent 8-bit chips, it has stricter refresh timings.
So in the case of doubt, we assume that 16-bit chips are used.
Additionally, only Allwinner A20 has all A0-A15 address lines and
can support densities up to 8192. The older Allwinner A10 and
Allwinner A13 can only support densities up to 4096.

We deliberately leave out DDR2, dual-rank configurations and the
special case of a 8-bit chip with density 8192. None of these
configurations seem to have been ever used in real devices. And no
new devices are likely to use these exotic configurations (because
only up to 2GB of RAM can be populated in any case).

This DRAM autodetection feature potentially allows to have a single
low performance fail-safe DDR3 initialiazation for a universal single
bootloader binary, which can be compatible with all Allwinner
A10/A13/A20 based devices (if the ifdefs are replaced with a runtime
SoC type detection).

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-08-12 08:42:34 +02:00
Siarhei Siamashka
935758b1d5 sunxi: dram: Derive write recovery delay from DRAM clock speed
The write recovery time is 15ns for all JEDEC DDR3 speed bins. And
instead of hardcoding it to 10 cycles, it is possible to set tighter
timings based on accurate calculations. For example, DRAM clock
frequencies up to 533MHz need only 8 cycles for write recovery.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-08-12 08:42:33 +02:00
Siarhei Siamashka
b5c71f5f9c sunxi: dram: Drop DDR2 support and assume only single rank DDR3 memory
All the known Allwinner A10/A13/A20 devices are using just single rank
DDR3 memory. So don't pretend that we support DDR2 or more than one
rank, because nobody could ever test these configurations for real and
they are likely broken. Support for these features can be added back
in the case if such hardware actually exists.

As part of this code cleanup, also replace division by 1024 with
division by 1000 for the refresh timing calculations. This allows
to use the original non-skewed tRFC timing table from the DRR3 spec
and make code less confusing.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-08-12 08:42:33 +02:00
Siarhei Siamashka
d755a5fb20 sunxi: dram: Configurable DQS gating window mode and delay
The hardware DQS gate training is a bit unreliable and does not
always find the best delay settings.

So we introduce a 32-bit 'dqs_gating_delay' variable, where each
byte encodes the DQS gating delay for each byte lane. The delay
granularity is 1/4 cycle.

Also we allow to enable the active DQS gating window mode, which
works better than the passive mode in practice. The DDR3 spec
says that there is a 0.9 cycles preamble and 0.3 cycle postamble.
The DQS window has to be opened during preamble and closed during
postamble. In the passive window mode, the gating window is opened
and closed by just using the gating delay settings. And because
of the 1/4 cycle delay granularity, accurately hitting the 0.3
cycle long postamble is a bit tough. In the active window mode,
the gating window is auto-closing with the help of monitoring
the DQS line, which relaxes the gating delay accuracy requirements.

But the hardware DQS gate training is still performed in the passive
window mode. It is a more strict test, which is reducing the results
variance compared to the training with active window mode.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-08-12 08:42:33 +02:00
Siarhei Siamashka
e044daa33e sunxi: dram: Add a helper function 'mctl_get_number_of_lanes'
It is going to be useful in more than one place.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-08-12 08:42:33 +02:00
Siarhei Siamashka
b8f7cb6ae3 sunxi: dram: Improve DQS gate data training error handling
The stale error status should be cleared for all sun4i/sun5i/sun7i
hardware and not just for sun7i. Also there are two types of DQS
gate training errors ("found no result" and "found more than one
possible result"). Both are handled now.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-08-12 08:42:33 +02:00
Siarhei Siamashka
013f2d7469 sunxi: dram: Use divisor P=1 for PLL5
This configures the PLL5P clock frequency to something in the ballpark
of 1GHz and allows more choices for MBUS and G2D clock frequency
selection (using their own divisors). In particular, it enables the use
of 2/3 clock speed ratio between MBUS and DRAM.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-08-12 08:42:33 +02:00
Siarhei Siamashka
1a9717cbb3 sunxi: dram: Configurable MBUS clock speed (use PLL5 or PLL6)
The sun5i hardware (Allwinner A13) introduced configurable MBUS clock
speed. Allwinner A13 uses only 16-bit data bus width to connect the
external DRAM, which is halved compared to the 32-bit data bus of sun4i
(Allwinner A10), so it does not make much sense to clock a wider
internal bus at a very high speed. The Allwinner A13 manual specifies
300 MHz MBUS clock speed limit and 533 MHz DRAM clock speed limit. Newer
sun7i hardware (Allwinner A20) has a full width 32-bit external memory
interface again, but still keeps the MBUS clock speed configurable.
Clocking MBUS too low inhibits memory performance and one has to find
the optimal MBUS/DRAM clock speed ratio, which may depend on many
factors:
    http://linux-sunxi.org/A10_DRAM_Controller_Performance

This patch introduces a new 'mbus_clock' parameter for the 'dram_para'
struct and uses it as a desired MBUS clock speed target. If 'mbus_clock'
is not set, 300 MHz is used by default to match the older hardcoded
settings.

PLL5P and PLL6 are both evaluated as possible clock sources. Preferring
the one, which can provide higher clock frequency that is lower or
equal to the 'mbus_clock' target. In the case of a tie, PLL5P has
higher priority.

Attempting to set the MBUS clock speed has no effect on sun4i, but does
no harm either.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-08-12 08:42:33 +02:00
Siarhei Siamashka
5c18384dea sunxi: dram: Re-introduce the impedance calibration ond ODT
The DRAM controller allows to configure impedance either by using the
calibration against an external high precision 240 ohm resistor, or
by skipping the calibration and loading pre-defined data. The DRAM
controller register guide is available here:

    http://linux-sunxi.org/A10_DRAM_Controller_Register_Guide#SDR_ZQCR0

The new code supports both of the impedance configuration modes:
   - If the higher bits of the 'zq' parameter in the 'dram_para' struct
     are zero, then the lowest 8 bits are used as the ZPROG value, where
     two divisors encoded in lower and higher 4 bits. One divisor is
     used for calibrating the termination impedance, and another is used
     for the output impedance.
   - If bits 27:8 in the 'zq' parameters are non-zero, then they are
     used as the pre-defined ZDATA value instead of performing the ZQ
     calibration.

Two lowest bits in the 'odt_en' parameter enable ODT for the DQ and DQS
lines individually. Enabling ODT for both DQ and DQS means that the
'odt_en' parameter needs to be set to 3.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-08-12 08:42:33 +02:00
Siarhei Siamashka
94cd301988 sunxi: dram: Add 'await_bits_clear'/'await_bits_set' helper functions
The old 'await_completion' function is not sufficient, because
in some cases we want to wait for bits to be cleared, and in the
other cases we want to wait for bits to be set. So split the
'await_completion' into two new 'await_bits_clear' and
'await_bits_set' functions.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-08-12 08:42:33 +02:00
Siarhei Siamashka
cfc89b003b sunxi: dram: Do DDR3 reset in the same way on sun4i/sun5i/sun7i
The older differences were likely justified by the need to mitigate
the CKE delay timing violations on sun4i/sun5i. The CKE problem is
already resolved, so now we can use the sun7i variant of this code
everywhere.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-08-12 08:42:32 +02:00
Siarhei Siamashka
7e40e1926a sunxi: dram: Remove broken impedance and ODT configuration code
We can safely remove it, because none of the currently supported
boards uses these features.

The existing implementation had multiple problems:
   - unnecessary code duplication between sun4i/sun5i/sun7i
   - ZQ calibration was never initiated explicitly, and could be
     only triggered by setting the highest bit in the 'zq' parameter
     in the 'dram_para' struct (this was never actually done for
     any of the known Allwinner devices).
   - even if the ZQ calibration could be started, no attempts were
     made to wait for its completion, or checking whether the
     default automatically initiated ZQ calibration is still
     in progress
   - ODT was only ever enabled on sun4i, but not on sun5i/sun7i

Additionally, SDR_IOCR was set to 0x00cc0000 only on sun4i. There
are some hints in the Rockchip Linux kernel sources, indicating
that these bits are related to the automatic I/O power down
feature, which is poorly understood on sunxi hardware at the
moment. Avoiding to set these bits on sun4i too does not seem to
have any measurable/visible impact.

The impedance and ODT configuration code will be re-introdeced in
one of the next comits.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-08-12 08:42:32 +02:00
Siarhei Siamashka
f8e88b6837 sunxi: dram: Fix CKE delay handling for sun4i/sun5i
Before driving the CKE pin (Clock Enable) high, the DDR3 spec requires
to wait for additional 500 us after the RESET pin is de-asserted.

The DRAM controller takes care of this delay by itself, using a
configurable counter in the SDR_IDCR register. This works in the same
way on sun4i/sun5i/sun7i hardware (even the default register value
0x00c80064 is identical). Except that the counter is ticking a bit
slower on sun7i (3 DRAM clock cycles instead of 2), resulting in
longer actual delays for the same settings.

This patch configures the SDR_IDCR register for all sun4i/sun5i/sun7i
SoC variants and not just for sun7i alone. Also an explicit udelay(500)
is added immediately after DDR3 reset for extra safety. This is a
duplicated functionality. But since we don't have perfect documentation,
it may be reasonable to play safe. Half a millisecond boot time increase
is not that significant. Boot time can be always optimized later.
Preferebly by the people, who have the hardware equipment to check the
actual signals on the RESET and CKE lines and verify all the timings.

The old code did not configure the SDR_IDCR register for sun4i/sun5i,
but performed the DDR3 reset very early for sun4i/sun5i. This resulted
in a larger time gap between the DDR3 reset and the DDR3 initialization
steps and reduced the chances of CKE delay timing violation to cause
real troubles.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-08-12 08:42:32 +02:00
Siarhei Siamashka
e626d2d446 sunxi: dram: Respect the DDR3 reset timing requirements
The RESET pin needs to be kept low for at least 200 us according
to the DDR3 spec. So just do it the right way.

This issue did not cause any visible major problems earlier, because
the DRAM RESET pin is usually already low after the board reset. And
the time gap before reaching the sunxi u-boot DRAM initialization
code appeared to be sufficient.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-08-12 08:42:32 +02:00
Siarhei Siamashka
f257796773 sunxi: dram: Remove broken super-standby remnants
If the dram->ppwrsctl (SDR_DPCR) register has the lowest bit set to 1,
this means that DRAM is currently in self-refresh mode and retaining the
old data. Since we have no idea what to do in this situation yet, just
set this register to 0 and initialize DRAM in the same way as on any
normal reboot (discarding whatever was stored there).

This part of code was apparently used by the Allwinner boot0 bootloader
to handle resume from the so-called super-standby mode. But this
particular code got somehow mangled on the way from the boot0 bootloader
to the u-boot-sunxi bootloader and has no chance of doing anything even
remotely sane. For example:
1. in the original boot0 code we had "mctl_write_w(SDR_DPCR,
   0x16510000)" (write to the register) and in the u-boot it now looks
   like "setbits_le32(&dram->ppwrsctl, 0x16510000)" (set bits in the
   register)
2. in the original boot0 code it was issuing three commands "0x12, 0x17,
   0x13" (Self-Refresh entry, Self-Refresh exit, Refresh), but in the
   u-boot they have become "0x12, 0x12, 0x13" (Self-Refresh entry,
   Self-Refresh entry, Refresh)

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-08-12 08:42:32 +02:00
Siarhei Siamashka
34759d74a3 sunxi: dram: Remove useless 'dramc_scan_dll_para()' function
The attempt to do DRAM parameters calibration in 'dramc_scan_dll_para()'
function by trying different DLL adjustments and using the hardware
DQS gate training result as a feedback is a great source of inspiration,
but it just can't work properly the way it is implemented now. The fatal
problem of this implementation is that the DQS gating window can be
successfully found for almost every DLL delay adjustment setup that
gets tried. Thus making it unable to see any real difference between
'good' and 'bad' settings.

Also this code was supposed to be only activated by setting the highest
bit in the 'dram_tpr3' variable of the 'dram_para' struct (per-board
dram configuration). But none of the linux-sunxi devices has ever used
it for real. Basically, this code is just a dead weight.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-08-12 08:42:32 +02:00
Stefano Babic
e82abaeb7f Merge branch 'master' of git://git.denx.de/u-boot-arm
Conflicts:
	boards.cfg

Signed-off-by: Stefano Babic <sbabic@denx.de>
2014-08-11 10:21:03 +02:00
maxin.john@enea.com
194c1ed400 emif.h: remove duplicated argument to |
Remove the duplicated argument to | in two places. Reported
by Coccinelle (http://coccinelle.lip6.fr/).

Signed-off-by: Maxin B. John <maxin.john@enea.com>
2014-08-09 11:17:03 -04:00
Albert ARIBAUD
1899fac925 Merge branch 'u-boot-sunxi/master' into 'u-boot-arm/master' 2014-08-09 16:48:34 +02:00
Peter Crosthwaite
fb8d876698 zynq: spl: Add vectors section to linker script
The vectors section contains the _start symbol which is used as the
program entry point. Add it to the linker script in same fashion as done
for regular u-boot. This allows for correct generation of an spl elf
with a non-zero entry point.

A similar change was applied to sunxi platform in
"sunxi: Fix u-boot-spl.lds to refer to .vectors"
(sha1: 9e5f80d823)

This also allows for placement of the vector table at the hivecs
location by setting the TEXT_BASE to 0xffff0000.

Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-08-08 11:27:29 +02:00
Fabio Estevam
9cd744ff11 mx6: crm_regs: Fix MXC_CCM_CIMR_MASK_PERIPH2_CLK_SEL_LOADED
According to the Reference Manual the 'mask_periph2_clk_sel_loaded' field of
register CCM_CIMR corresponds to bit 19 so fix its definition accordingly.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-08-08 10:29:40 +02:00
Fabio Estevam
326454a88d mx6: crm_regs: Fix MXC_CCM_CLPCR_WB_PER_AT_LPM definition
According to the Reference Manual the 'wb_per_at_lpm' field of register
CCM_CLPCR corresponds to bit 16 so fix its definition accordingly.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-08-08 10:29:40 +02:00
Fabio Estevam
338c9da605 mx6: crm_regs: Fix CDCDR_SPDIF0_CLK_PODF mask and offset
According to the Reference Manual the 'spdif0_clk_podf' field of register
CCM_CDCDR corresponds to bits 22, 23 and 24, so fix the mask and offset
definitions accordingly.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-08-08 10:29:40 +02:00
Fabio Estevam
2834490245 mx6: imx-regs: Remove unused 'omux' field from iomux struct
'omux' field is not used anywhere and such layout is not valid for mx6solox.

Instead of adding more ifdef's into the structure, let's simply remove this
unused 'omux' field.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2014-08-08 10:29:39 +02:00
Stefano Babic
c23154aab5 Merge branch 'master' of git://git.denx.de/u-boot-arm 2014-08-08 10:18:40 +02:00
Tom Rini
aa159e681e Merge http://git.denx.de/u-boot-dm 2014-08-04 10:16:27 -04:00
Simon Glass
76a1e584e1 arm: Support pre-relocation malloc()
Add support for re-relocation malloc() in arm's start-up code.

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-08-04 05:24:35 -06:00
Simon Glass
aae2aef9c8 arm: Set up global data before board_init_f()
At present arm defines CONFIG_SYS_GENERIC_GLOBAL_DATA, meaning that
the global_data pointer is set up in board_init_f(). However it is
actually set up before this, it just isn't zeroed.

If we zero the global data before calling board_init_f() then we
don't need to define CONFIG_SYS_GENERIC_GLOBAL_DATA.

Make this change (on arm32 only) to simplify the init process. I
don't have the ability to test aarch64 yet.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Tom Rini <trini@ti.com>
2014-08-04 05:23:59 -06:00
Marek Vasut
dae0f5c644 mmc: s3c: Add SD driver
Implement SD driver for the S3C24xx family. This implementation
is currently only capable of using the PIO transfers, DMA is not
supported.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-08-01 19:24:34 +03:00
Marek Vasut
7eca6b6327 arm: s3c: Unify the S3C24xx SDI structure
Unify the register structure so they can be easily used across all
of S3C24xx lineup.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-08-01 19:24:23 +03:00
DrEagle
3fe3b4fb1c ARM: kirkwood: add mvsdio driver
This patch add Marvell kirkwood MVSDIO/MMC driver
and enable it for Sheevaplugs and OpenRD boards.

Signed-off-by: Gerald Kerma <drEagle@doukki.net>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-08-01 18:44:56 +03:00
Marc Zyngier
d5db7024aa sunxi: HYP/non-sec: add sun7i PSCI backend
So far, only supporting the CPU_ON method.
Other functions can be added later.

Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-07-31 15:37:24 +02:00
Hans de Goede
fc70300136 sunxi: Add CONFIG_MACPWR option
On some boards the ethernet-phy needs to be powered up through a gpio,
add support for this.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-07-31 15:37:23 +02:00
Roman Byshko
06cdd94077 sunxi: add defines to control USB Host clocks/resets
The commit adds three defines which will be used in
the EHCI driver to enable USB clock and assert
reset controllers of the corresponding PHYs.

Signed-off-by: Roman Byshko <rbyshko@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-07-31 15:37:22 +02:00
Ian Campbell
a6e50a88d8 ahci: provide sunxi SATA driver using AHCI platform framework
This enables the necessary clocks, in AHB0 and in PLL6_CFG. This is done
for sun7i only since I don't have access to any other sunxi platforms
with sata included.

The PHY setup is derived from the Alwinner releases and Linux, but is mostly
undocumented.

The Allwinner AHCI controller also requires some magic (and, again,
undocumented) DMA initialisation when starting a port.  This is added under a
suitable ifdef.

This option is enabled for Cubieboard, Cubieboard2 and Cubietruck based on
contents of Linux DTS files, including SATA power pin config taken from the
DTS. All build tested, but runtime tested on Cubieboard2 and Cubietruck only.

Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-07-31 15:37:22 +02:00
Masahiro Yamada
90f984e397 kconfig: delete redundant CONFIG_${ARCH} definition
CONFIG_${ARCH} is defined by Kconfig.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2014-07-30 14:42:02 -04:00
Masahiro Yamada
dd84058d24 kconfig: add board Kconfig and defconfig files
This commit adds:
 - arch/${ARCH}/Kconfig
    provide a menu to select target boards
 - board/${VENDOR}/${BOARD}/Kconfig or board/${BOARD}/Kconfig
    set CONFIG macros to the appropriate values for each board
 - configs/${TARGET_BOARD}_defconfig
    default setting of each board

(This commit was automatically generated by a conversion script
based on boards.cfg)

In Linux Kernel, defconfig files are located under
arch/${ARCH}/configs/ directory.
It works in Linux Kernel since ARCH is always given from the
command line for cross compile.

But in U-Boot, ARCH is not given from the command line.
Which means we cannot know ARCH until the board configuration is done.
That is why all the "*_defconfig" files should be gathered into a
single directory ./configs/.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
2014-07-30 08:48:01 -04:00
Tom Rini
362f16b1e9 Merge branch 'master' of git://git.denx.de/u-boot-arm 2014-07-29 09:41:35 -04:00
Marc Zyngier
9d195a5461 ARM: HYP/non-sec: remove MIDR check to validate CBAR
Having a form of whitelist to check if we know of a CPU core
and and obtain CBAR is a bit silly.

It doesn't scale (how about A12, A17, as well as other I don't know
about?), and is actually a property of the SoC, not the core.

So either it works and everybody is happy, or it doesn't and
the u-boot port to this SoC is providing the real address via
a configuration option.

The result of the above is that this code doesn't need to exist,
is thus forcefully removed.

Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-07-28 17:19:55 +02:00
Marc Zyngier
e771a3d538 ARM: HYP/non-sec/PSCI: emit DT nodes
Generate the PSCI node in the device tree.

Also add a reserve section for the "secure" code that lives in
in normal RAM, so that the kernel knows it'd better not trip on
it.

Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-07-28 17:19:52 +02:00
Ma Haijun
e29607ed97 ARM: convert arch_fixup_memory_node to a generic FDT fixup function
Some architecture needs extra device tree setup. Instead of adding
yet another hook, convert arch_fixup_memory_node to be a generic
FDT fixup function.

[maz: collapsed 3 patches into one, rewrote commit message]

Signed-off-by: Ma Haijun <mahaijuns@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-07-28 17:19:49 +02:00
Marc Zyngier
38510a4b34 ARM: HYP/non-sec: add the option for a second-stage monitor
Allow the switch to a second stage secure monitor just before
switching to non-secure.

This allows a resident piece of firmware to be active once the
kernel has been entered (the u-boot monitor is dead anyway,
its pages being reused).

Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-07-28 17:19:26 +02:00
Marc Zyngier
ecf07a7930 ARM: HYP/non-sec: add generic ARMv7 PSCI code
Implement core support for PSCI. As this is generic code, it doesn't
implement anything really useful (all the functions are returning
Not Implemented).

Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-07-28 17:19:18 +02:00
Marc Zyngier
f510aeae68 ARM: HYP/non-sec: allow relocation to secure RAM
The current non-sec switching code suffers from one major issue:
it cannot run in secure RAM, as a large part of u-boot still needs
to be run while we're switched to non-secure.

This patch reworks the whole HYP/non-secure strategy by:
- making sure the secure code is the *last* thing u-boot executes
  before entering the payload
- performing an exception return from secure mode directly into
  the payload
- allowing the code to be dynamically relocated to secure RAM
  before switching to non-secure.

This involves quite a bit of horrible code, specially as u-boot
relocation is quite primitive.

Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-07-28 17:19:09 +02:00
Marc Zyngier
bf433afd60 ARM: HYP/non-sec: add separate section for secure code
In anticipation of refactoring the HYP/non-secure code to run
from secure RAM, add a new linker section that will contain that
code.

Nothing is using it just yet.

Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-07-28 17:07:23 +02:00
Marc Zyngier
b726d22da9 ARM: add missing HYP mode constant
In order to be able to use the various mode constants (far more
readable than random hex values), add the missing HYP and A
values.

Also update arm/lib/interrupts.c to display HYP instead of an
unknown value.

Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-07-28 17:06:35 +02:00
Marc Zyngier
64fd44dcae ARM: non-sec: reset CNTVOFF to zero
Before switching to non-secure, make sure that CNTVOFF is set
to zero on all CPUs. Otherwise, kernel running in non-secure
without HYP enabled (hence using virtual timers) may observe
timers that are not synchronized, effectively seeing time
going backward...

Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-07-28 17:06:28 +02:00
Marc Zyngier
800c83522c ARM: HYP/non-sec: add a barrier after setting SCR.NS==1
A CP15 instruction execution can be reordered, requiring an
isb to be sure it is executed in program order.

Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-07-28 17:06:19 +02:00
Marc Zyngier
c19e0dd741 ARM: HYP/non-sec: move switch to non-sec to the last boot phase
Having the switch to non-secure in the "prep" phase is causing
all kind of troubles, as that stage can be called multiple times.

Instead, move the switch to non-secure to the last possible phase,
when there is no turning back anymore.

Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-07-28 17:05:59 +02:00
Albert ARIBAUD
b1cdd8baa1 Merge branch 'u-boot-ti/master' into 'u-boot-arm/master' 2014-07-28 12:26:21 +02:00
Albert ARIBAUD
48b3ed217f Merge branch 'u-boot-sh/rmobile' into 'u-boot-arm/master' 2014-07-28 10:54:54 +02:00
Albert ARIBAUD
740f41d3cb Merge branch 'u-boot-sunxi/master' into 'u-boot-arm/master' 2014-07-28 10:12:45 +02:00
pekon gupta
222a3113b4 ARM: omap: clean redundant PISMO_xx macros used in OMAP3
PISMO_xx macros were used to define 'Platform Independent Storage MOdule'
related GPMC configurations. This patch
- Replaces these OMAP3 specific macros with generic CONFIG_xx macros as provided
  by current u-boot infrastructure.
- Removes unused redundant macros, which are no longer required after
  merging of common platform code in following commit
      commit a0a37183bd
      ARM: omap: merge GPMC initialization code for all platform

+-----------------+-----------------------------------------------------------+
| Macro           | Reason for removal                                        |
+-----------------+-----------------------------------------------------------+
| PISMO1_NOR_BASE | duplicate of CONFIG_SYS_FLASH_BASE                        |
+-----------------+-----------------------------------------------------------+
| PISMO1_NAND_BASE| duplicate of CONFIG_SYS_NAND_BASE                         |
+-----------------+-----------------------------------------------------------+
| PISMO1_ONEN_BASE| duplicate of CONFIG_SYS_ONENAND_BASE                      |
+-----------------+-----------------------------------------------------------+
| PISMO1_NAND_SIZE| GPMC accesses NAND device via I/O mapped registers so     |
|                 | configuring GPMC chip-select for smallest allowable       |
|                 | segment (GPMC_SIZE_16M) is enough.                        |
+-----------------+-----------------------------------------------------------+
| PISMO1_ONEN_SIZE| OneNAND uses a fixed GPMC chip-select address-space of    |
|                 | 128MB (GPMC_SIZE_128M)                                    |
+-----------------+-----------------------------------------------------------+
+-----------------+-----------------------------------------------------------+
| PISMO1_NOR      |  Unused Macros                                            |
| PISMO1_NAND     |                                                           |
| PISMO2_CS0      |                                                           |
| PISMO2_CS1      |                                                           |
| PISMO1_ONENAND  |                                                           |
| PISMO2_NAND_CS0 |                                                           |
| PISMO2_NAND_CS1 |                                                           |
| PISMO1_NOR_BASE |                                                           |
| PISMO1_NAND_BASE|                                                           |
| PISMO2_CS0_BASE |                                                           |
+-----------------+-----------------------------------------------------------+

Signed-off-by: Pekon Gupta <pekon@ti.com>
2014-07-25 16:26:12 -04:00
pekon gupta
77cd89e755 ARM: omap: fix GPMC address-map size for NAND and NOR devices
Fixes commit a0a37183bd
    ARM: omap: merge GPMC initialization code for all platform

1) NAND device are not directly memory-mapped to CPU address-space, they are
 indirectly accessed via following GPMC registers:
 - GPMC_NAND_COMMAND_x
 - GPMC_NAND_ADDRESS_x
 - GPMC_NAND_DATA_x
 Therefore from CPU's point of view, NAND address-map can be limited to just
 above register addresses. But GPMC chip-select address-map can be configured
 in granularity of 16MB only.
 So this patch uses GPMC_SIZE_16M for all NAND devices.

2) NOR device are directly memory-mapped to CPU address-space, so its
 address-map size depends on actual addressable region in NOR FLASH device.
 So this patch uses CONFIG_SYS_FLASH_SIZE to derive GPMC chip-select address-map
 size configuration.

Signed-off-by: Pekon Gupta <pekon@ti.com>
2014-07-25 16:26:12 -04:00
Rajendra Nayak
8c16dd6fa7 ARM: OMAP: Fix handling of errata i727
The errata is applicable on all OMAP4 (4430 and 4460/4470) and OMAP5
ES 1.0 devices. The current revision check erroneously implements this
on all DRA7 varients and with DRA722 device (which has only 1 EMIF instance)
infact causes an asynchronous abort and ends up masking it in CPSR,
only to be uncovered once the kernel switches to userspace.

Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2014-07-25 16:26:11 -04:00
Hao Zhang
a906847966 board: k2e-evm: add board support
This patch adds Keystone2 k2e_evm evaluation board support.

Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-07-25 16:26:11 -04:00
Khoronzhuk, Ivan
1284246eb9 ARM: keystone2: spl: add K2E SoC support
Keystone2 K2E SoC has slightly different spl pll settings then
K2HK, so correct this.

Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-07-25 16:26:11 -04:00
Hao Zhang
20187fd11c ARM: keystone2: add MSMC cache coherency support for K2E SOC
This patch adds Keystone2 K2E SOC specific code to support
MSMC cache coherency. Also create header file for msmc to hold
its API.

Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-07-25 16:26:11 -04:00
Hao Zhang
4dca7f0acc ARM: keystone2: clock: add K2E clock support
This patch adds clock definitions and commands to support Keystone2
K2E SOC.

Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-07-25 16:26:11 -04:00
Hao Zhang
5c76f78858 ARM: keystone2: add K2E SoC hardware definitions
This patch adds hardware definitions specific to Keystone II
K2E device. It has a lot common definitions with k2hk SoC, so
move them to common hardware.h. This is preparation patch for
adding K2E SoC support.

Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-07-25 16:26:11 -04:00
Khoronzhuk, Ivan
8dfc15f56c ARM: keystone: clock: move K2HK SoC dependent code in separate file
This patch in general spit SoC type clock dependent code and general
clock code. Before adding keystone II Edison k2e SoC which has
slightly different dpll set, move k2hk dependent clock code to
separate clock-k2hk.c file.

Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-07-25 16:26:10 -04:00
Khoronzhuk, Ivan
3d31538625 k2hk: use common KS2_ prefix for all hardware definitions
Use KS2_ prefix in all definitions, for that replace K2HK_ prefix and
add KS2_ prefix where it's needed. It requires to change names also
in places where they're used. Align lines and remove redundant
definitions in kardware-k2hk.h at the same time.

Using common KS2_ prefix helps resolve redundant redefinitions and
adds opportunity to use KS2_ definition across a project not thinking about
what SoC should be used. It's more convenient and we don't need to worry
about the SoC type in common files, hardware.h will think about that.
The hardware.h decides definitions of what SoC to use.

Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-07-25 16:26:10 -04:00
Hao Zhang
7b26c1f608 keystone2: add possibility to turn off all dsps
By default all DSPs are turned off, for another case option
to turn off them is added in this commit.
Also add command to turn off itself.

Acked-by: Murali Karicheri <m-maricheri2@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-07-25 16:26:10 -04:00
Hao Zhang
4984bce41f keystone2: move cpu_to_bus() to keystone.c
The SoC related common functions in board.c should be placed to
a common keystone.c arch file.

Acked-by: Murali Karicheri <m-maricheri2@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-07-25 16:26:10 -04:00
Khoronzhuk, Ivan
35c547c2bc ARM: keystone2: keystone_nav: make it dependent on keystone driver
This driver is needed in case if keystone driver is used.
Currently only keystone_net driver uses it. So to avoid
redundant code compilation make the keystone_nav dependent
on keystone net driver. It also leads to compilation errors
for boards that does't use it.

Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-07-25 16:26:09 -04:00
Hao Zhang
101eec50f0 keystone2: ddr: add DDR3 PHY configs updated for PG 2.0
Add DDR3 PHY configs updated for PG 2.0
Also add DDR3A PHY reset before init for PG2.0 SoCs.

Acked-by: Murali Karicheri <m-maricheri2@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-07-25 16:26:09 -04:00
Khoronzhuk, Ivan
0b86858956 keystone: ddr3: add ddr3.h to hold ddr3 API
It's convinient to hold ddr3 function definitions in separate file
such as ddr3.h. So move this from hardware.h to ddr3.h.

Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-07-25 16:26:09 -04:00
Khoronzhuk, Ivan
04b7ce0773 ARM: keystone2: psc: use common PSC base
Use common keystone2 Power Sleep controller base address instead of
directly deciding which keystone2 SoC is used in psc module.

Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-07-25 16:26:09 -04:00
Stefan Roese
6d3bbdb0e7 ARM: omap: Remove unused arch/arm/cpu/armv7/omap3/mem.c
These functions have been merged into the common GPMC init code
with this commit a0a37183 (ARM: omap: merge GPMC initialization code
for all platform). The file is not compiled any more. So remove it
as well.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Pekon Gupta <pekon@ti.com>
Cc: Tom Rini <trini@ti.com>
Acked-by: Pekon Gupta <pekon@ti.com>
2014-07-25 16:26:09 -04:00
Stefan Roese
fb2fcb798a ARM: omap: Fix GPMC init for OMAP3 platforms
Commit a0a37183 (ARM: omap: merge GPMC initialization code for all
platform) broke NAND on OMAP3 based platforms. I noticed this while
testing the latest 2014.07-rc version on the TAO3530 board. NAND
detection did not work with this error message:

NAND:  nand: error: Unable to find NAND settings in GPMC Configuration - quitting

As OMAP3 configs don't set CONFIG_NAND but CONFIG_NAND_CMD. the GPMC
was not initialized for NAND at all. This patch now fixes this issue.

Tested on TAO3530 board.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Pekon Gupta <pekon@ti.com>
Cc: Tom Rini <trini@ti.com>
Acked-by: Pekon Gupta <pekon@ti.com>
2014-07-25 16:26:09 -04:00
Tom Rini
c4f80f5003 am335x_evm / gumstix pepper: Correct DDR settings
As noted by clang, we have been shifting certain values out of 32bit
range when setting some DDR registers.  Upon further inspection these
had been touching reserved fields (and having no impact).  These came in
from historical bring-up code and can be discarded.  Similarly, we had
been declaring some fields as 0 when they will be initialized that way.
Tested on Beaglebone White.

Reported-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Cc: Ash Charles <ash@gumstix.com>
Signed-off-by: Tom Rini <trini@ti.com>
Tested-By: Ash Charles <ashcharles@gmail.com>
2014-07-25 16:26:08 -04:00
Nobuhiro Iwamatsu
fafcfc5a98 arm: rmobile: Add support R8A7794
Renesas R8A7794 is CPU with Cortex-A15. This supports the basic register
definition and GPIO and framework of PFC.

Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2014-07-24 14:03:46 +09:00
Michal Simek
03606ff42e ARM: zynq: Show ECC status on the same line as DRAM size
Without this patch is DRAM size one line below DRAM:
which is not nice

Origin:
I2C:   ready
DRAM:  Memory: ECC disabled
1 GiB
MMC:   zynq_sdhci: 0

Fixed by this patch:
I2C:   ready
DRAM:  ECC disabled 1 GiB
MMC:   zynq_sdhci: 0

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-07-23 15:36:55 +02:00
Heiko Schocher
a0ae0091d7 i.MX6: add enable_spi_clk()
add enable_spi_clk(), so board code can enable spi clocks.

Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Stefano Babic <sbabic@denx.de>
2014-07-23 12:25:42 +02:00
Heiko Schocher
aafe4020c1 i.MX6: define struct pwm_regs and PWMCR_* defines
add defines for pwm modul found on imx6.

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2014-07-23 12:25:41 +02:00
Heiko Schocher
4a4d3a7db7 imx6: add gpr2 usb_otg_id iomux select control define
add IOMUXC_GPR1_USB_OTG_ID_OFFSET and IOMUXC_GPR1_USB_OTG_ID_SEL_MASK
define for the USB_OTG_ID_SEL bit.

Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
2014-07-23 12:25:41 +02:00
Fabio Estevam
aeadf0655c mx6: Adjust the GPR offset for mx6solox
On mx6solox there is an additional 0x4000 offset for the GPR registers.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2014-07-23 12:25:41 +02:00
Fabio Estevam
0a11d6f29c mx6: Remove duplication of iomuxc structure
There is no need to keep iomuxc_base_regs structure as it serves the exact same
purpose of the iomuxc structure, which is to provide access to the GPR
registers.

The additional fields of iomuxc_base_regs are not used. Other advantage of
'iomuxc' is that it has a shorter name and the variable declarations can fit
into a single line.

So remove iomuxc_base_regs structure and use iomuxc instead.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2014-07-23 12:25:41 +02:00
Fabio Estevam
a3df99b50f mx6: soc: Do not apply the PFD erratum for mx6solox
The PFD issue is not present on mx6solox, so skip it in this case.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-07-23 12:25:40 +02:00
York Sun
8340e7ac86 driver/ddr: Fix DDR4 driver for ARM
Previously the driver was only tested on Power SoCs. Different barrier
instructions are needed for ARM SoCs.

Signed-off-by: York Sun <yorksun@freescale.com>
2014-07-22 16:25:54 -07:00
Ian Campbell
7c48b01510 sunxi: use setbits_le32 to enable the DMA clock
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Hans de Goede <hdegoede@redhat.com>
2014-07-18 19:42:25 +01:00
Ian Campbell
abce2c6220 sunxi: add gpio driver
This patch enables CONFIG_CMD_GPIO for the Allwinner (sunxi) platform as well
as providing the common gpio API (gpio_request/free, direction in/out, get/set
etc).

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ma Haijun <mahaijuns@gmail.com>
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: Henrik Nordström <henrik@henriknordstrom.net>
Cc: Tom Cubie <Mr.hipboi@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
2014-07-18 19:42:25 +01:00
Hans de Goede
ae5de5a19d sunxi: Fix reset hang on sun5i
Do the same as the Linux kernel does, this fixes the SoC hanging on reset
about 50% of the time.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-07-18 19:42:22 +01:00
Hans de Goede
6620377e4b sunxi: Add i2c support
Add support for the i2c controller found on all Allwinner sunxi SoCs,
this is the same controller as found on the Marvell orion5x and kirkwood
SoC families, with a slightly different register layout, so this patch uses
the existing mvtwsi code.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-By: Prafulla Wadaskar <prafulla@marvell.com>
Acked-by: Heiko Schocher <hs@denx.de>
[ ijc -- updated u-boot-spl-fel.lds ]
2014-07-18 19:41:30 +01:00
Hans de Goede
0db2bbdc04 mvtwsi: convert to CONFIG_SYS_I2C framework
Note this has only been tested on Allwinner sunxi devices (support for which
gets introduced by a later patch).

The kirkwood changes have been compile tested using the wireless_space board
config, the orion5x changes have been compile tested using the edminiv2 board
config.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heiko Schocher <hs@denx.de>
2014-07-16 19:56:24 +01:00
Stefano Babic
dab5e3469d Merge branch 'master' of git://git.denx.de/u-boot
Signed-off-by: Stefano Babic <sbabic@denx.de>

Conflicts:
	boards.cfg
2014-07-16 08:51:30 +02:00
Tom Rini
84f24ac827 Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2014-07-11 14:54:48 -04:00
Fabio Estevam
d95b6ab87c mx6: clock: Do not enable sata and ipu clocks
mx6sx does not have sata nor ipu blocks, so do not handle such clocks.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-07-10 15:29:16 +02:00
Fabio Estevam
f586040451 mx6sx: Add pin definitions
Add the pin definitions for mx6sx.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-07-10 15:29:16 +02:00
Fabio Estevam
05d54b827f mx6: Add support for the mx6solox variant
mx6solox is the newest member of the mx6 family.

Some of the new features on this variants are:
- Cortex M4 microcontroller (besides the CortexA9)
- Dual Gigabit Ethernet

Add the initial support for it.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-07-10 15:29:16 +02:00
Eric Nelson
e153333eeb i.MX6DL/S: add drive-strength back to pads DISP0_DAT2/DAT10
The pad settings for DISP0_DATA02 and DISP0_DAT10 were not
set in the same way as DISP0_DAT00-23, causing much flicker
in parallel RGB displays on Dual-Lite and Solo processors.

These settings now match the i.MX6 Dual and Quad core versions.

Note that this fixes a regression in commit b47abc3 and that
this is the second time we've had a regression on these two
pads (See commit e654ddf).

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
2014-07-10 15:23:56 +02:00
Felipe Balbi
5ba95541b7 usb: phy: omap_usb_phy: implement usb_phy_power() for AM437x
Newer AM437x silicon requires us to explicitly power up
the USB2 PHY. By implementing usb_phy_power() we can
achieve that.

Signed-off-by: Felipe Balbi <balbi@ti.com>
2014-07-09 22:11:51 +02:00
Tom Rini
22692ec0fb Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2014-07-09 09:21:51 -04:00
Fabio Estevam
157f45da91 mx6: soc: Update the comments of set_ldo_voltage()
Commit 3d622b78 (mx6: soc: Introduce set_ldo_voltage()) introduces
set_ldo_voltage() function that can be used to set the voltages
of any of the three LDO regulators controlled by the PMU_REG_CORE register.

Prior to this commit there was a single set_vddsoc() which only configured the
VDDSOC regulator.

Update the comments to align with the new set_ldo_voltage() implementation.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-07-09 15:10:10 +02:00
Andre Renaud
2eb268f6fd MX6: Correct calculation of PLL_SYS
DIV_SELECT is used as Fout = Fin * div_select / 2.0, so we should do
the shift after the multiply to avoid rounding errors

Signed-off-by: Andre Renaud <andre@bluewatersys.com>
2014-07-09 14:55:30 +02:00
Ian Campbell
799aff38df sunxi: Avoid unused variable warning.
Mark rc as __maybe_unused since it is infact unused on systems with neither
EMAC nor GMAC.

Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Tom Rini <trini@ti.com>
2014-07-08 07:45:06 +01:00
Alexey Ignatov
072b2d8872 kmake: include DTB section into u-boot.bin if CONFIG_OF_EMBED enabled
Fixes a bug when objcopy doesn't put .dtb.init.rodata section to resulting
u-boot.bin, so u-boot was unable to find embedded DTB.
2014-07-07 19:47:24 -04:00
Cooper Jr., Franklin
8038b497e7 am43xx: Tune the system to avoid DSS underflows
* This is done by limiting the ARM's bandwidth and setting DSS priority in
  the EMIF controller to ensure underflows do not occur.
2014-07-07 19:42:34 -04:00
Franklin S. Cooper Jr
2c95211167 am43xx: Update EMIF DDR3 Configuration for AM43x GP
* Boot failures have been discovered due to a combination of routing issues and
  non optimal ddr3 timings in the EMIF
* Since ddr3 timings are different after significant board layout changes
  different timings are required for alpha, beta and production boards.

Signed-off-by: Franklin S. Cooper Jr <fcooper@ti.com>
2014-07-07 19:42:34 -04:00
Jeroen Hofstee
878cae6b02 ARM: emif4: wait for CM_DLL_READYST to be set
The code intends for the CM_DLL_READYST to be set, but
actually polls till any bit is set since the logical
AND is used instead of the bitwise one is used. Fix it.

cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-07-07 19:42:33 -04:00
Tom Rini
6ee3d00d1d Merge branch 'master' of git://git.denx.de/u-boot-i2c 2014-07-07 10:10:52 -04:00
Hans de Goede
c26fb9db0e sunxi: Add emac glue, enable emac on the cubieboard
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-07-06 20:12:45 +01:00
Hans de Goede
f84269c5c0 sunxi: Add sun5i support
Add support for the Allwinner A13 and A10s SoCs also know as the Allwinner
sun5i family, and the A13-OLinuXinoM A13 based and r7-tv-dongle A10s based
boards.

The only differences compared to the already supported sun4i and sun7i
families are all in the DRAM controller initialization:

-Different hcpr values
-Different MBUS settings
-Some other small initialization changes

Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-07-06 20:12:44 +01:00
Hans de Goede
745325a97d sunxi: Add sun4i support
Add support for the Allwinner A10 SoC also known as the Allwinner sun4i family,
and add the Cubieboard board which uses the A10 SoC.

Compared to sun7 only the DRAM controller is a bit different:
-Controller reset bits are inverted, but only for Rev. A
-Different hpcr values
-No MBUS on sun4i
-Various other initialization changes

Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-07-06 20:12:44 +01:00
Hans de Goede
c7e79dec85 sunxi: Implement reset_cpu
There is no way to reset the cpu, so use the watchdog for this.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-07-06 20:12:44 +01:00
Hans de Goede
9e5f80d823 sunxi: Fix u-boot-spl.lds to refer to .vectors
Adjust the u-boot-spl.lds linker script to match the changes made in the
41623c91b0 "arm: move exception handling out
of start.S files" commit.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-07-06 17:41:13 +01:00
Chin Liang See
23f23f23d5 socfpga: Relocate arch common functions away from board
To move the arch common function away from board folder to
arch/arm/cpu/armv7/socfpga folder. Its to avoid code duplication
for other non Altera dev kit which is using socfpga device.

Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Cc: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Detlev Zundel <dzu@denx.de>
2014-07-05 10:14:46 +02:00
Shaibal.Dutta
fe0d925299 arm: Fix armv8 compilation error
Fix following compilation error when CONFIG_ARM64 is defined

Error: unknown or missing system register name at operand 2
-- `mrs x0,daifmsr daifset,#3'

Signed-off-by: Shaibal.Dutta <shaibal.dutta@broadcom.com>
Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Reviewed-by: Darwin Rambo <drambo@broadcom.com>
2014-07-05 09:30:20 +02:00
Jeroen Hofstee
ed6c7f7f6e arm: spl: fix include guard
cc: Tom Rini <trini@ti.com>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-07-05 09:28:21 +02:00
Chin Liang See
dc4d4aa14b socfpga: Adding Scan Manager driver
Scan Manager driver will be called to configure the IOCSR
scan chain. This configuration will setup the IO buffer settings

Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Wolfgang Denk <wd@denx.de>
CC: Pavel Machek <pavel@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
2014-07-05 00:27:27 +02:00
Chin Liang See
05b884b5cd socfpga: Adding DesignWare watchdog support
To enable the DesignWare watchdog support at SOCFPGA
Cyclone V dev kit.

Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
2014-07-05 00:24:18 +02:00
Sergey Kostanbaev
7237d22baa arm: ep9315: Return back Cirrus Logic EDB9315A board support
This patch returns back support for old ep93xx processors family

Signed-off-by: Sergey Kostanbaev <sergey.kostanbaev@gmail.com>
Cc: albert.u.boot@aribaud.net
2014-07-04 23:45:48 +02:00
Jeroen Hofstee
fcfddfd504 ARM: cache_v7: use __weak
This is not only more readable but also prevents a warning
about a missing prototype. The prototypes which are actually
missing are added.

cc: Albert Aribaud <albert.u.boot@aribaud.net>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Reviewed-by: Tom Rini <trini@ti.com>
2014-07-04 19:57:22 +02:00
York Sun
f749db3a75 ARMv8/ls2085a_emu: Add LS2085A emulator and simulator board support
LS2085A is an ARMv8 implementation. This adds board support for emulator
and simulator:
  Two DDR controllers
  UART2 is used as the console
  IFC timing is tightened for speedy booting
  Support DDR3 and DDR4 as separated targets
  Management Complex (MC) is enabled
  Support for GIC 500 (based on GICv3 arch)

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Arnab Basu <arnab.basu@freescale.com>
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
2014-07-04 19:48:41 +02:00
J. German Rivera
b940ca64b2 armv8/fsl-lsch3: Add support to load and start MC Firmware
Adding support to load and start the Layerscape Management Complex (MC)
firmware. First, the MC GCR register is set to 0 to reset all cores. MC
firmware and DPL images are copied from their location in NOR flash to
DDR. MC registers are updated with the location of these images.
Deasserting the reset bit of MC GCR register releases core 0 to run.
Core 1 will be released by MC firmware. Stop bits are not touched for
this step. U-boot waits for MC until it boots up. In case of a failure,
device tree is updated accordingly. The MC firmware image uses FIT format.

Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Lijun Pan <Lijun.Pan@freescale.com>
Signed-off-by: Shruti Kanetkar <Shruti@Freescale.com>
2014-07-03 08:40:58 +02:00
York Sun
2f78eae506 ARMv8/FSL_LSCH3: Add FSL_LSCH3 SoC
Freescale LayerScape with Chassis Generation 3 is a set of SoCs with
ARMv8 cores and 3rd generation of Chassis. We use different MMU setup
to support memory map and cache attribute for these SoCs. MMU and cache
are enabled very early to bootst performance, especially for early
development on emulators. After u-boot relocates to DDR, a new MMU
table with QBMan cache access is created in DDR. SMMU pagesize is set
in SMMU_sACR register. Both DDR3 and DDR4 are supported.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Varun Sethi <Varun.Sethi@freescale.com>
Signed-off-by: Arnab Basu <arnab.basu@freescale.com>
2014-07-03 08:40:51 +02:00
York Sun
22932ffc03 ARMv8: Adjust MMU setup
Make MMU function reusable. Platform code can setup its own MMU tables.

Signed-off-by: York Sun <yorksun@freescale.com>
CC: David Feng <fenghua@phytium.com.cn>
2014-07-03 08:40:48 +02:00
J. German Rivera
0d031e046c Added 64-bit MMIO accessors for ARMv8
This is needed for accessing peripherals with 64-bit MMIO registers,
from ARMv8 processors.

Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
2014-07-03 08:40:31 +02:00
Darwin Rambo
261d27605c arm: Add support for semihosting for armv8 fastmodel targets.
The armv8 ARM Trusted Firmware (ATF) can be used to load various ATF
images and u-boot, and does this for virtual platforms by using
semihosting. This commit extends this idea by allowing u-boot to also
use semihosting to load the kernel/ramdisk/dtb. This eliminates the need
for a bootwrapper and produces a more realistic boot sequence with
virtual models.

Though the semihosting code is quite generic, support for armv7 in
fastmodel is less useful due to the wide range of available silicon
and the lack of a free armv7 fastmodel, so this change contains an
untested armv7 placeholder for the service trap opcode.

Please refer to doc/README.semihosting for a more detailed description
of semihosting and how it is used with the armv8 virtual platforms.

Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Cc: trini@ti.com
Cc: fenghua@phytium.com.cn
Cc: bhupesh.sharma@freescale.com
2014-07-03 08:35:45 +02:00
Stephen Warren
68049a082b i2c: tegra: use repeated start for reads
I2C read transactions are typically implemented as follows:

START(write) address REPEATED_START(read) data... STOP

However, Tegra's I2C driver currently implements reads as follows:

START(write) address STOP START(read) data... STOP

This sequence confuses at least the AS3722 PMIC on the Jetson TK1 board,
leading to corrupted read data in some cases. Fix the driver to chain
the transactions together using repeated starts to solve this.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Yen Lin <yelin@nvidia.com>
2014-07-03 06:29:19 +02:00
Albert ARIBAUD
304f936aea Merge remote-tracking branch 'u-boot-samsung/master'
Conflicts:
	boards.cfg

Conflict was trivial between goni maintainer change and
lager_nor removal.
2014-07-01 20:52:51 +02:00
Albert ARIBAUD
019b57cc1d Merge branch 'u-boot-tegra/master' into 'u-boot-arm/master' 2014-07-01 15:48:25 +02:00
Albert ARIBAUD
e99f30e105 Merge branch 'u-boot-ti/master' into 'u-boot-arm/master' 2014-07-01 15:11:18 +02:00
Albert ARIBAUD
d6694aff56 Merge branch 'u-boot-imx/master' into 'u-boot-arm/master' 2014-06-30 23:00:34 +02:00
Stefano Babic
5d2ad2bc33 vf610: fix build due to missing sys_proto.h
commit 67a04ab3ab
fix the build for MX25. The same error
happens for VF610 SOC.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2014-06-25 12:48:06 +02:00
Albert ARIBAUD
01a3647abd Merge branch 'u-boot-microblaze/zynq' into 'u-boot-arm/master' 2014-06-25 10:40:23 +02:00
Albert ARIBAUD
ed1d98d801 Merge branch 'u-boot/master' into 'u-boot-arm/master' 2014-06-25 10:39:58 +02:00
Akshay Saraswat
8e4ab1d582 Exynos5420: Introduce support for the Peach-Pit board
While the Exynos5420 chip is used in both Smdk5420 and in the Peach-Pit
line of devices, there could be other boards using the same chip, so a
common configuration file is being added (exynos5420.h) as well
as two common device tree files (exynos54xx.dtsi & exynos5420.dtsi).

The peach board as declared in boards.cfg is a copy of smdk5420
declaration. The configuration files are similar, but define different
default device trees, console serial ports and prompts.

The device tree files for smdk5420 and peach-pit inherit from the same
common file.

Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-06-23 08:45:44 +09:00
Akshay Saraswat
eacf46d340 Exynos5420: Let macros be used for exynos5420
Macros defined in exynos5_setup.h specific to SMDK5420
are required for Peach-Pit too. Hence, replacing
CONFIG_SMDK5420 with CONFIG_EXYNOS5420 to enable these
macros for all the boards based on Exynos5420.

Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-06-23 08:45:44 +09:00
Simon Glass
8946034a31 tegra: dts: Bring in GPIO bindings from linux
These files are taken from Linux 3.14.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
2014-06-20 11:56:33 -06:00
Simon Glass
5957ac2a9f Makefile: Support include files for .dts files
Linux supports this, and if we are to have compatible device tree files,
U-Boot should also.

Avoid giving the device tree files access to U-Boot's include/ directory.
Only include/dt-bindings is accessible.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-06-20 11:55:03 -06:00
Simon Glass
ad827e1649 arm: Support iotrace feature
Support the iotrace feature for ARM, when enabled.

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-06-20 11:54:40 -06:00
Stefano Babic
734af242c2 OMAP: disable gpmc timeout safely for reenabling
gpmc timeout is disabled and the reset counter
is set to 0. However, if later a driver activates
the timeout setting the reset to a valid value,
the old reset value with zero is still valid
for the first access. In fact, the timeout block
loads the reset counter after a successful access.

Found on a am335x board with a FPGA connected
to the GPMC bus together with the NAND.
When the FPGA driver in kernel activates
the timeout, the system hangs at the first access
by the NAND driver.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2014-06-19 17:53:59 -04:00
Jeroen Hofstee
fd3f401bc1 omap3: board: trivial: add void for no args
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-06-19 17:53:58 -04:00
Felipe Balbi
9f1220a9ca cpu: armv7: am33x: ddr: write emif ref_ctrl_shadow register
Signed-off-by: Felipe Balbi <balbi@ti.com>
2014-06-19 17:53:58 -04:00
Khoronzhuk, Ivan
909ea9aa26 ARM: keystone: aemif: move aemif driver to drivers/memory/ti-aemif.c
Move AEMIF driver to drivers/memory/ti-aemif.c along with AEMIF
definitions collected in arch/arm/include/asm/ti-common/ti-aemif.h

Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-06-19 17:53:58 -04:00
Khoronzhuk, Ivan
3e01ed00da mtd: nand: davinci: add header file for driver definitions
The definitions inside emif_defs.h concern davinci nand driver and
should be in it's header. So create header file for davinci nand
driver and move definitions from emif_defs.h and nand_defs.h to it.

Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
[trini: Fixup more davinci breakage]
Signed-off-by: Tom Rini <trini@ti.com>
2014-06-19 17:53:58 -04:00
Ash Charles
2868a5dff3 omap: Don't enable GPMC CS0 with nothing attached
If CONFIG_(NAND|NOR|ONENAND) is not defined, no configuration is set
for GPMC on chip select #0---size is 0.  In this case, the GPMC
configuration should be reset but not enabled.  Enabling causes the
Gumstix DuoVero board to hang when entering Linux.

Signed-off-by: Ash Charles <ashcharles@gmail.com>
[trini: Switch to testing base as GPMC_SIZE_256M is 0x0]
Signed-off-by: Tom Rini <trini@ti.com>
2014-06-19 17:53:41 -04:00
Jeroen Hofstee
c42ff090e4 tegra20: display: fix checking of return value
The calling code seems a bit in doubt about the return
value of fdtdec_lookup_phandle. Since it returns a negative
value on error (and fdt_node_offset_by_phandle as well),
check for that.

cc: Wei Ni <wni@nvidia.com>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-06-19 09:18:05 -07:00
Stefano Babic
f2f07e8553 imx: correct HAB status for new chip TO
According to:

http://git.freescale.com/git/cgit.cgi/imx/uboot-imx.git/log/?h=imx_v2009.08_3.0.35_4.1.0

ENGR00287268 mx6: fix the secure boot issue on the new tapout chip
commit 424cb1a79e9f5ae4ede9350dfb5e10dc9680e90b

newer i.MX6 silicon revisions have an updated ROM and HAB API table.
Please see also:

i.MX Applications Processors Documentation
Engineering Bulletins
EB803, i.MX 6Dual/6Quad Applications Processor Silicon Revsion 1.2 to 1.3 Comparison

With this change the secure boot status is correctly displayed

Signed-off-by: Stefano Babic <sbabic@denx.de>
2014-06-17 17:45:09 +02:00
Fabio Estevam
bad40e089f mx6: Fix definition of IOMUXC_GPR12_DEVICE_TYPE_RC
mx6 reference manual incorrectly states that the DEVICE_TYPE field of
IOMUXC_GPR12 register should be configured as '0010' for setting the PCI
controller in RC mode. The correct value should be '0100' instead.

This also aligns with the same value used in the mx6 pci kernel driver.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
2014-06-17 16:27:51 +02:00
Masahiro Yamada
a811db5a8c arm: zynq: fix a bug in Zynq linker script
Commit 41623c91 moved exception handlers to ".vectores" section
but it missed to adjust Zynq linker script.

Zynq boards hang up after relocation because "_start" symbol
does not point to the correct address and gd->relocaddr gets insane.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Michal Simek <monstr@monstr.eu>
Tested-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-06-17 12:28:26 +02:00
Wu, Josh
d337a09c30 ARMv7: at91: enable ICache and DCache.
For at91 armv7 SoC (SAMA5D3x), only LCD and macb used DMA.
Now as the lcd and macb driver already support dcache. So we can
enable dcache now.

Also we can enable icache without any problem.

Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-06-14 18:07:03 +02:00
Akshay Saraswat
ed32522fe0 Exynos5420: DMC: Add software read leveling
Sometimes Read DQ and DQS are not in phase. Since, this
phase shift differs from board to board, we need to
calibrate it at DRAM init phase, that's read DQ calibration.
This patch adds SW Read DQ calibration routine to compensate
this skew.

Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-06-13 17:05:14 +09:00
Doug Anderson
c9334fcda9 DMC: exynos5420: Gate CLKM to when reading PHY_CON13
when CLKM is running.  If we stop CLKM when sampling it the glitches
all go away, so we'll do that as per Samsung suggestion.

We also check the "is it locked" bits of PHY_CON13 and loop until they
show the the value sampled actually represents a locked value.  It
doesn't appear that the glitching and "is it locked" are related, but
it seems wise to wait until the PHY tells us the value is good before
we use it.  In practice we will not loop more than a couple times (and
usually won't loop at all).

Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-06-13 17:05:13 +09:00
Akshay Saraswat
aacdd79095 Exynos5420: Remove code for enabling read leveling
This patch intends to remove all code which enables hardware read
leveling. All characterization environments may not cope up with
h/w read leveling enabled, so we must disable this.
Also, disabling h/w read leveling improves the MIF LVcc value
(LVcc value is the value at which DDR will fail to work properly).
Improving LVcc means we have enough voltage margin for MIF.
When h/w leveling is enabled, we have almost zero volatge margin.

Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-06-13 17:05:13 +09:00
Akshay Saraswat
cfde7588d8 Exynos5: DMC: Modify the definition of ddr3_mem_ctrl_init
Passing fewer arguments is better and mem_iv_size is never
used. Let's keep only one argument and make it cleaner.

Signed-off-by: Hatim Ali <hatim.rv@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-06-13 17:05:13 +09:00
Minkyu Kang
7922a2d479 Revert "exynos: Enable PSHOLD in SPL"
This reverts commit eb0dd9986c.
2014-06-13 17:00:56 +09:00
Vasili Galka
7d89982b7a Remove ${objtree}/include/asm/proc/ link
mkconfig links ${objtree}/include/asm/proc/ to
${srctree}/arch/${arch}/include/asm/proc-armv/. This seems to be a
remnant from the past. Ever since its introduction in 2003 it is used
only in ARM build and always links to same place, so let's simplify
the code, remove it and reference directly where needed.

Successful MAKEALL for ARM and PowerPC verified on Linux.

Signed-off-by: Vasili Galka <vvv444@gmail.com>
2014-06-11 16:27:05 -04:00
Vasili Galka
4b9ca09399 cosmetic: Whitespace fix
Signed-off-by: Vasili Galka <vvv444@gmail.com>
2014-06-11 16:27:05 -04:00
Thomas Betker
73671dad49 Check run_command() return code properly
run_command() returns 0 for success, 1 for failure. Fix places which
assume that failure is indicated by a negative return code.

Signed-off-by: Thomas Betker <thomas.betker@rohde-schwarz.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Tested-by: Stefan Roese <sr@denx.de>
2014-06-11 16:25:47 -04:00
Simon Glass
5cc16cbf25 am33xx/omap: Enable CONFIG_OF_CONTROL
Add support for device tree control and add device tree files for the
beaglebone black initially.

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-06-11 16:25:46 -04:00
Simon Glass
7e4154a553 am33xx/omap: Allow cache enable for all Sitara/OMAP
Enable the cache for all devices, unless CONFIG_SYS_DCACHE_OFF is defined.
This speeds up the Beaglebone Black boot considerable.

(Tested only on Beaglebone Black with SD card boot)

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-06-11 16:25:39 -04:00
Masahiro Yamada
0a26e1d6c3 arm: fix a double-definition error of _start symbol
The symbol "_start" is defined twice in arch/arm/lib/vectors.S:
around line 48 and line 54.

If CONFIG_SYS_DV_NOR_BOOT_CFG is defined (as on calimain board),
build fails:

  arch/arm/lib/vectors.S: Assembler messages:
  arch/arm/lib/vectors.S:54: Error: symbol `_start' is already defined
  make[1]: *** [arch/arm/lib/vectors.o] Error 1
  make: *** [arch/arm/lib] Error 2

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
2014-06-09 10:36:40 +02:00
Mark Rutland
b924d586d7 arm64: zero cntvoff_el2
Currently cntvoff_el2 is initialised with an arbitrary bag of bits
derived from the initial value of cnthctl_el2 on the current CPU. This is
somewhat odd and problematic as some of these bits are UNKNOWN at reset
and may differ across CPUs (which may cause an OS at EL1 to observe time
going backwards across CPUs).

This patch instead initialises cntvoff_el2 with xzr, giving the register
a consistent value of zero on all CPUs.

Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: David Feng <fenghua@phytium.com.cn>
Cc: Tom Rini <trini@ti.com>
Acked-by: David.Feng <fenghua@phytium.com.cn>
2014-06-09 10:24:02 +02:00
Chao Fu
cb6d04d606 arm: vf610: Add QSPI support for VF610TWR
Add QSPI support for VF610TWR, such as clock and iomux.

Signed-off-by: Alison Wang <Huan.Wang@freescale.com>
Signed-off-by: Chao Fu <b44548@freescale.com>
2014-06-09 09:18:15 +02:00
Alison Wang
9d2ca0984b arm: imx: Add two macros for VF610 in IOMUX_PAD structure
Add PAD_CTL_DSE_150ohm and PAD_CTL_PUS_22K_UP for VF610 in
IOMUX_PAD structure.

Signed-off-by: Alison Wang <Huan.Wang@freescale.com>
2014-06-09 09:18:12 +02:00
Tom Rini
55e8250bd3 Merge branch 'master' of git://git.denx.de/u-boot-arm 2014-06-08 07:58:41 -04:00
Albert ARIBAUD
5ed28948a3 Merge branch 'u-boot-ti/master' into 'u-boot-arm/master' 2014-06-08 09:14:19 +02:00
Tom Rini
64ce2fbd6c arm:am33xx: Add a scale_vcores() hook
Similar to OMAP4/5 we need to scale the voltage up prior to changing the
clock frequencies up higher.  Add a similar hook to start with.

Signed-off-by: Tom Rini <trini@ti.com>
2014-06-06 17:46:16 -04:00
Hannes Petermaier
25b0a729aa arch-am33xx: Add defines for timer0-7
For usage of timer6 within B&R we need this defines to enable clock
modules and clk-source.

Also the 'Timer register bits' are expanded.

By the way we add defines for all timers within AM335x SoC.

Cc: trini@ti.com
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
2014-06-06 17:46:15 -04:00
Lokesh Vutla
ccd2f8db81 ARM: AM43xx: Fix UART clocks enabling
After enabling a module, SW has to wait on IDLEST bit
until it is Fully functional. This wait is missing for UART module
and there is a immediate access of UART registers after this. So there
is a chance of hang on this module( This can happen when we are running
from MPU SRAM). So waiting for IDLEST bit.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2014-06-06 17:46:15 -04:00
Murali Karicheri
afee59cd49 keystone: init: enable UART1 to be able use it from kernel
Currently PWREMU_MGMT is not configured in the Linux generic UART
driver as this register seems to be specific TI UART IP. So this
needs to be enabled in u-boot to use UART1 from kernel space.

Acked-By: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-06-06 17:46:14 -04:00
Tom Rini
196311dc72 arm:am33xx: Rework s_init and add board_early_init_f
With the changes to the i2c framework (and adopting the omap24xx_i2c
driver to them) we can no longer call i2c functions prior to gd having
been set and cleared.  When SPL booting, this is handled by setting gd
to point to SRAM in s_init.  However in the cases where we are loaded
directly by ROM (memory mapped NOR or QSPI) we need to make use of the
normal hooks to slightly delay these calls.

Signed-off-by: Tom Rini <trini@ti.com>
2014-06-06 17:46:14 -04:00
Tom Rini
87acf194a2 arm:am33xx: Make dram_init call sdram_init() in some contexts
We have two contexts for booting these platforms.  One is SPL which is
roughly: reset, cpu_init_crit, lowlevel_init, s_init, sdram_init, _main,
board_init_f from SPL, ... then U-Boot loads.  The other is a
memory-mapped XIP case (NOR or QSPI) where we do not run an SPL.  In
this case we go, roughly: reset, cpu_init_crit, lowlevel_init, s_init,
_main, regular board_init_f.

In the first case s_init will set a valid gd and then be able to call
sdram_init which in many cases will need i2c (which needs a valid gd for
gd->cur_i2c_bus).  In this second case we must (and are able to and
should) defer sdram_init() into dram_init() called by board_init_f as gd
will have been set in _main and cleared in board_init_f.

Signed-off-by: Tom Rini <trini@ti.com>
2014-06-06 17:46:14 -04:00
Sourav Poddar
7a5f71bc40 am43xx_evm: Add qspiboot target
The ePOS EVM and EVM SK have QSPI as an option to boot.  Add a qspiboot
target that utilizes QSPI for env and so forth as an example of best
practices.  As QSPI is booted from directly we need to chang
CONFIG_SYS_TEXT_BASE.

Note that on ePOS EVM the QSPI and NAND are mutually exclusive choices
we need to handle that elsewhere, once NAND support is also added.

Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
2014-06-06 17:46:12 -04:00
pekon gupta
68128e0a86 omap3: remove remnant macros GPMC_NAND_ECC_LP_x8_LAYOUT and GPMC_NAND_ECC_LP_x16_LAYOUT
OMAP3 used GPMC_NAND_ECC_LP_x8_LAYOUT and GPMC_NAND_ECC_LP_x16_LAYOUT macros
to configure GPMC controller for x7 or x8 bit device connected to its interface.
Now this information is encoded in CONFIG_SYS_NAND_DEVICE_WIDTH macro, so above
macros can be completely removed.

Signed-off-by: Pekon Gupta <pekon@ti.com>
2014-06-06 17:46:07 -04:00
Stefano Babic
67a04ab3ab MX25: fix build due to missing sys_proto.h
THe mx25 arch does not have a sys_proto.h file.
Instead of creating a dummy file, the file
is not included for this SOC.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2014-06-06 10:58:47 +02:00
Tim Harvey
22452fd821 imx: sata: return failure if not IMX6Q/IMX6D
The IMX6QUAD/DUAL have SATA, but the IMX6SOLO/DL do not. Return
instead of configuring the SATA clock and GPR13 registers.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2014-06-06 10:14:52 +02:00
Tim Harvey
5bf497e3fd imx: iomux: add macros to setup iomux for multiple SoC types
Allow imx_iomux_v3_setup_multiple_pads to take a multi-cpu pad_list
and add macros for declaring the pad_list that take into account the
SoC types supported using CONFIG_MX6QDL (supports both the MX6Q and MX6DL
iomux).

Cc: Stefan Roese <sr@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Andy Ng <andreas2025@gmail.com>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Tom Rini <trini@ti.com>

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2014-06-06 10:07:26 +02:00
Tim Harvey
fe0f7f7842 mx6: add mmdc configuration for MX6Q/MX6DL
- add function for configuring iomux based on board-specific regs
- add function for configuring mmdc based on board-specific and
  chip-specific data

Cc: Stefan Roese <sr@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Andy Ng <andreas2025@gmail.com>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Tom Rini <trini@ti.com>

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2014-06-06 10:07:26 +02:00
Tim Harvey
8d05b161fc mx6: add structs for mmdc and ddr iomux registers
Add memory-mapped structures for MMDC iomux and configuration. Note that whi
the MMDC configuration registers are common between the IMX6DQ
(IMX6DUAL/IMX6QUAD) and IMX6SDL (IMX6SOLO/IMX6DUALLITE) types the iomux
registers differ. This requires two sets of structures.

Add structures to describe DDR3 device information, system information
(memory layout, etc), and MMDC calibration registers that can be used to
configure the MMDC dynamically.

We define these structures for SPL builds instead of including mx6q-ddr.h an
mx6dl-ddr.h which use the same namespace and are only useful for imximage cf
files.

Cc: Stefan Roese <sr@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Andy Ng <andreas2025@gmail.com>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Tom Rini <trini@ti.com>

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
2014-06-06 10:07:25 +02:00
Tim Harvey
b07161c321 imx: add comments and remove unused struct fields
Add comment block for the imx_ddr_size function and remove the extra unused
fields from struct esd_mmdc_regs which are also not common between IMX53 and
IMX6.

Cc: Stefan Roese <sr@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Andy Ng <andreas2025@gmail.com>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Tom Rini <trini@ti.com>

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
2014-06-06 10:07:25 +02:00
Tim Harvey
887717dbb9 mx6: add boot device support for SPL
Add a common spl.c file to support boot device functions needed for SPL
such as detecting the boot device.

Cc: Stefan Roese <sr@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Andy Ng <andreas2025@gmail.com>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Tom Rini <trini@ti.com>

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
2014-06-06 10:07:25 +02:00
Masahiro Yamada
9f2ec3f543 spl: consolidate arch/arm/include/asm/arch-*/spl.h
arch/arm/include/asm/spl.h requires all SoCs to have
arch/arm/include/asm/arch-*/spl.h.

But many of them just define BOOT_DEVICE_* macros.

Those macros are used in the "switch (boot_device) { ... }"
statement in common/spl/spl.c.

So they should not be archtecture specific, but be described as
a simpile enumeration.

This commit merges most of arch/arm/include/asm/arch-*/spl.h
into arch/arm/include/asm/spl.h.

With a little more effort, arch-zynq/spl.h and arch-socfpga/spl.h
will be merged, while I am not sure about OMAP and Exynos.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Tom Warren <twarren@nvidia.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Minkyu Kang <mk7.kang@samsung.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
Acked-by: Michal Simek <monstr@monstr.eu>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Tested-by: Bo Shen <voice.shen@atmel.com> [on sama5d3xek board for at91 part]
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stefano Babic <sbabic@denx.de> [applying Tim's i.MX6 patches]
Acked-by: Tom Rini <trini@ti.com>
2014-06-06 10:05:34 +02:00
Masahiro Yamada
ba8dd7755e kbuild: move cmd_mkimage to scripts/Makefile.lib
Because cmd_mkimage is used in various subdirectories,
it seems reasonable to define it in scripts/Makefile.lib.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-06-05 17:01:58 -04:00
Masahiro Yamada
2aff23cadf arm: fdt_control: fix a build error with CONFIG_OF_EMBED=y
The build fails if a non-generic ARM board is compiled
with CONFIG_OF_EMBED=y.

The correct symbol name for embedded FDT is not __dtb_db_begin,
but __dtb_dt_begin. (A typo introduced by commit 6ab6b2af)

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
2014-06-05 14:38:38 -04:00
Stephen Warren
e6607cffef ARM: tegra: enable USB device mode and UMS on some boards
For each of Jetson TK1, Venice2, and Beaver:

- Enable the first USB controller in DT, and describe its configuration.

- Enable USB device/gadget support. This allows the user to type e.g.
  "ums 0 mmc 0" at the command-line to cause U-Boot to act a USB device
  implementing the USB Mass Storage protocol, and expose MMC device 0
  that way.

This allows a host PC to mount the Tegra device's MMC, partition it, and
install a filesystem on it.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-06-05 11:25:54 -07:00
Albert ARIBAUD
cc49da249c Merge branch 'u-boot-samsung/master' into 'u-boot-arm/master' 2014-06-02 08:43:48 +02:00
Doug Anderson
567802bbd6 Exynos: Make sure ps_hold gets set in the SPL
Setting ps_hold ought to be one of the first things we do when we
first boot up. If we wait until the main u-boot runs we won't set it
in time and the PMIC may power us back off.

Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-05-31 14:22:20 +09:00