replace info logs with debug logs
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Waiting 150us TC bit couldn't be enough.
If TFA lets 16 bits in USART fifo, we has to wait 16 times 87 us (time
of 10 bits (1 byte in most use cases) at a baud rate of 115200).
Fixes: b4dbc5d65a ("serial: stm32: Wait TC bit before performing initialization")
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
To disabled a clock in clock tree initialization for a mux of STM32MP15,
the selected clock source index is set with the latest possible index for
the number of bit used. Today this valid configuration cause a error
in U-Boot messages, for example with CLK_ETH_DISABLED, when this clock
is not needed for the used ETH PHY without crystal:
no parents defined for clk id 123
This patch change the level of this message to avoid this trace for
valid clock tree.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Select the same mac divider for SGMII too as the one being used for
QSGMII.
Enable full rate divider configuration support for J721E_WIZ_10G for
SGMII.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Enhance the AM65 CPSW NUSS driver to perform a MDIO reset using a GPIO
line. Logic is also added to perform a pre and post delay around reset
using the optional 'reset-delay-us' and 'reset-post-delay-us' properties.
This is similar to the reset being performed in the Linux kernel. The
reset is done once when the CPSW MDIO bus is being initialized.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
The PSIL endpoint data for J721E currently covers only the MCU domain
CPSW0 instance. Add the data for the MAIN domain CPSW0 as well to allow
the MAIN domain Ethernet ports to be usable on any platform using J721E
SoC.
Additionally, since J721E's PSIL endpoint data is applicable to J7200
SoC as well, the MAIN CPSW0 instance on J7200 will also be usable now.
Signed-off-by: Suman Anna <s-anna@ti.com>
[s-vadapalli@ti.com: Update commit message indicating support for J7200]
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
The MVTWSI controller can act either as a master or slave device. When
acting as a master, the FSM is driven by the CPU. As a slave, the FSM is
driven by the bus directly. In what is (apparently) a safety mechanism,
if the bus transitions our FSM in any improper way, the FSM goes to a
"bus error" state (0x00). I could find no documented or experimental way
to get the FSM out of this state, except for a controller reset.
Since U-Boot only uses the MVTWSI controller as a bus master, this
feature only gets in the way: we do not care what happened on the bus
previously as long as the bus is ready for a new transaction. So, when
trying to start a new transaction, check for this state and reset the
controller if necessary.
Note that this should not be confused with the "deblocking" technique
(used by the `i2c reset` command), which involves pulsing SCL repeatedly
if SDA is found to be held low, in an attempt to force the bus back to
an idle state. This patch only resets the controller in case something
else had previously upset it, and (in principle) results in no
externally-observable change in behavior.
Signed-off-by: Sam Edwards <CFSworks@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
The current gpio-uclass design uses name field in struct gpio_dev_priv as
an indicator that GPIO is claimed by consumer. This overloads the function
of name field and does not work well for named pins not configured as GPIO
pins.
Introduce separate bitfield array as the claim indicator.
This unbreaks dual-purpose AF and GPIO operation on STM32MP since commit
2c38f7c318 ("pinctrl: pinctrl_stm32: Populate uc_priv->name[] with pinmux node's name")
where any pin which has already been configured as AF could no longer be
claimed as dual-purpose GPIO. This is important for pins like STM32 MMCI
st,cmd-gpios .
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a new DM driver supporting FTPCI100 IP used in SoC designs.
This implementation is not based on the old non-DM ftpci100 code
dropped from U-Boot.
Enable the driver in sandbox_defconfig to test compilability.
Signed-off-by: Sergei Antonov <saproj@gmail.com>
This function only ever returns 0, but may not assign the second
parameter. Same thing for device_find_next_child(). Do not assign
ret to stop proliferation of this misuse.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
This is merely a dummy driver that makes sure the DWC3 XHCI driver
finds its reset and PHY controllers. We rely on iBoot to set up
the PHY for us.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
The Apple hardware supports 64-bit prefetchable memory windows so
enable CONFIG_SYS_PCI_64BIT. This fixes BAR assignments for the
Broadcom Ethernet controller used in some of the desktop machines.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
With the commit 4fcba5d556 ("regulator: implement basic reference
counter"), keeping regulator enablement in balance become more important.
Disable vqmmc-supply before signal voltage is changed to keep regulator
enable counter in balance.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
With the commit 4fcba5d556 ("regulator: implement basic reference
counter") the return value of regulator_set_enable may be EALREADY or
EBUSY for fixed/gpio regulators.
Change to use the more relaxed regulator_set_enable_if_allowed to
continue if regulator already was enabled or disabled.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # P895 Tegra 3;
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # rockpro64-rk3399
With the commit 4fcba5d556 ("regulator: implement basic reference
counter") the return value of regulator_set_enable may be EALREADY or
EBUSY for fixed/gpio regulators.
Change to use the more relaxed regulator_set_enable_if_allowed to
continue if regulator already was enabled or disabled.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Marek Vasut <marex@denx.de>
With the commit 4fcba5d556 ("regulator: implement basic reference
counter") the return value of regulator_set_enable may be EALREADY or
EBUSY for fixed/gpio regulators.
Change to use the more relaxed regulator_set_enable_if_allowed to
continue if regulator already was enabled or disabled.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # rockpro64-rk3399
Reviewed-by: Marek Vasut <marex@denx.de>
With the commit 4fcba5d556 ("regulator: implement basic reference
counter") the return value of regulator_set_enable may be EALREADY or
EBUSY for fixed/gpio regulators.
Change to use the more relaxed regulator_set_enable_if_allowed to
continue if regulator already was enabled or disabled.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # rockpro64-rk3399
On RK3568 most pins have a configurable drive strength of level 0-5 and
some pins level 0-11. When rk3568_set_drive is called with a strength
value above 7 the drv value written to reg may overflow into the write
enable bits, resulting in a bad configuration.
This cause e.g. ethernet PHY on Radxa CM3-IO board not to work after
drive is configured according to the device tree.
Could not get PHY for ethernet@fe010000: addr 0
Level 6-11 can be configured using a second reg for some pins, however
the drv value is reused resulting in lower 6 bits being written to reg.
Input schmitt is configured in 2-bit fields on RK3568 compared to
earlier generation and 2'b10 should be used to enable input schmitt.
Change to use regmap_update_bits with a rmask to fix the overflow issue
and closer match the linux driver. Bit shift the drv value used for the
second reg to configure drive strength level 6-11. Also write correct
values for input schmitt setting.
Fixes: 1977d746aa ("rockchip: rk3568: add rk3568 pinctrl driver")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
When the fkms dtb overlay is used only the simple-framebuffer is
presented as a usable video display. So, add "simple-framebuffer"
compatible to enable video driver bcm2835.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Meng Li <Meng.Li@windriver.com>
At present vidconsole_measure() tests ops->select_font before calling
ops->measure, which would result in a null dereference when the console
driver provides no ops for measure.
Fixes: b828ed7d79 ("console: Allow measuring the bounding box of text")
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Once all the other drivers got torn down in preparation for the OS
to start, tear down the clock controller last. The clock controller
must be torn down last as some of the clock which get turned off
might have still been needed during the teardown stage of the other
drivers.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Tam Nguyen <tam.nguyen.xa@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Add support to read RK3308 registers used to configure UART clocks, and
thus to get UART rate and baudrate. This fixes clock_get_rate returning
error on serial device probing. Moreover, there is no need anymore to
use 'clock-frequency' property for UART nodes in *-u-boot.dtsi files
for all cases where UART is not inited by U-Boot proper or by SPL o by
TPL code but by a preliminary external boot phase (for Rock PI S, UART
is inited by external TPL).
Signed-off-by: Massimo Pegorer <massimo.pegorer+oss@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
As per definitions of masks and shift offsets in cru_rk3308.h, values
read from registers must be first masked and then shifted. By the way,
this fix is binary invariant, because in all of fixed cases the shift
offset is zero.
Signed-off-by: Massimo Pegorer <massimo.pegorer+oss@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Pine64 Quartz64 boards DT reference SCLK_GMAC1_RGMII_SPEED in the
assigned-clocks property of the gmac1 node. This result in a ENOENT
error when driver core tries to set a parent for this clock.
The clock speed in rgmii/rmii mode is changed using clk_set_rate of the
tx_rx clock and not using clk_set_parent of the speed clock.
Add dummy support for SCLK_GMAC1_RGMII_SPEED and similar clocks to clk
driver to allow a driver for gmac node to probe.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The clock driver for RK3568 does not include support for UART clocks in
SPL. This result in the following message with high enough loglevel.
ns16550_serial serial@fe660000: pinctrl_select_state_full: uclass_get_device_by_phandle_id: err=-19
Fix this by including support for UART clocks in SPL.
Fixes: 4a262feba3 ("rockchip: rk3568: add clock driver")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The field for clk_cpll_div_25m_div in CRU_CLKSEL_CON81 is 6 bits wide,
not 5 bits wide as currently defined in CPLL_25M_DIV_MASK.
Fix this and the assert so that CPLL_25M can be assigned a 25 MHz rate.
Fixes: 4a262feba3 ("rockchip: rk3568: add clock driver")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Fix use of wrong clk selection for CLK_PWM1 on RK3568.
Fixes: 4a262feba3 ("rockchip: rk3568: add clock driver")
Signed-off-by: Damon Ding <damon.ding@rock-chips.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
533ad9dc avoided an overflow but causes compilation
failure on 32bit boards (eg. veyron speedy)
this commit uses div_u64 which has a fallback codepath
for 32bit platforms
Signed-off-by: Alvaro Fernando García <alvarofernandogarcia@gmail.com>
Tested-by: Simon Glass <sjg@chromium.org> # chromebook_jerry
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The PCIe driver for RK3399 is affected by a similar issue that was fixed
for RK35xx in the commit e04b67a7f4 ("pci: pcie_dw_rockchip: release
resources on failing probe").
Resources are not released on failing probe, e.g. regulators may be left
enabled and the ep-gpio may be left in a requested state.
Change to use regulator_set_enable_if_allowed and disable regulators
after failure to keep regulator enable count balanced, ep-gpio is also
released on regulator failure.
Also add support for the vpcie12v-supply, remove unused include and
check return value from dev_read_addr_name.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
ftwdt010_wdt_start() has to call ftwdt010_wdt_reset() after setting-up
the timeout in the same fashion ftwdt010_wdt_expire_now() does it.
Without this patch the "wdt start <ms>" command does not actually start
the watchdog timer until the "wdt reset" command is executed.
Signed-off-by: Sergei Antonov <saproj@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Get the correct ECAM offset and record the secondary bus
number in Multiple RC case.
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
At present this feature is enabled in SPL if a bloblist is available.
Some platforms may not want to use this, so add an option to allow the
feature to be disabled.
Note that the feature unfortunately only fills in part of the
video-handoff information, so causes failures on x86 platforms. For now,
disable it there.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com> # qemu-x86_64
Drop the duplication and add a single rule which can handle SPL as well.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Use the correct function here, since there may be multiple IDE devices
available.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
This name is a little confusing since it suggests that it sets up the
sibling block device. In fact it sets up a bootdev for it. Rename the
function to make this clearer.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
When USB finds no devices it currently returns -EPERM which bootstd does
not understand. This causes other bootdevs of the same priority to be
skipped.
Fix this by returning the correct error code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Now all linker symbols are declared as type char[]. Though we can
reference the address via both the array name 'var' and its address
'&var'. It's better to unify them to avoid confusing developers.
This patch converts all '&var' linker symbol refrences to the most
commonly used format 'var'.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
It is not a parse error to have a default value of "0" for a "hex" type
entry, instead of "0x0". However, "0" and "0x0" are not treated the
same even by the tools themselves. Correct this by changing the default
value from "0" to "0x0" for all hex type questions that had the
incorrect default. Fix one instance (in two configs) of a default of "0"
being used on a hex question to be "0x0". Remove the cases where a
defconfig had set a value of "0x0" to be used as the default had been
"0".
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
If an error message contains a function name, it should match the name of
the function throwing the message.
Fixes: 7739d93d82 ("pci: Match region flags using a mask")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
We know that "pa" is non-NULL so it's nicer to just return zero instead
of return !pa. This has no effect on runtime behavior.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
The "oftree_count" is the number of entries which have been set in
the oftree_list[] array. If all the entries have been initialized then
this off by one would result in reading one element beyond the end
of the array.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
The ec_command_inptr() function returns negative error codes or
the number of bytes that it was able to read. The cros_ec_get_sku_id()
function should return negative error codes. Right now it returns
positive error codes or negative byte counts.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Both the Linux kernel and libbsd agree that strlcpy() should always
return strlen(src) and not include the NUL termination. The incorrect
U-Boot implementation makes it impossible to check the return value for
truncation, and breaks code written with the usual implementation in
mind (for example, fdtdec_add_reserved_memory() was subtly broken).
I reviewed all callers of strlcpy() and strlcat() and fixed them
according to my understanding of the intended function.
This reverts commit d3358ecc54 and adds
related fixes.
Fixes: d3358ecc54 ("lib: string: Fix strlcpy return value")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
Provide armffa command showcasing the use of the U-Boot FF-A support
armffa is a command showcasing how to invoke FF-A operations.
This provides a guidance to the client developers on how to
call the FF-A bus interfaces. The command also allows to gather secure
partitions information and ping these partitions. The command is also
helpful in testing the communication with secure partitions.
For more details please refer to the command documentation [1].
A Sandbox test is provided for the armffa command.
[1]: doc/usage/cmd/armffa.rst
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Cc: Jens Wiklander <jens.wiklander@linaro.org>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Emulate Secure World's FF-A ABIs and allow testing U-Boot FF-A support
Features of the sandbox FF-A support:
- Introduce an FF-A emulator
- Introduce an FF-A device driver for FF-A comms with emulated Secure World
- Provides test methods allowing to read the status of the inspected ABIs
The sandbox FF-A emulator supports only 64-bit direct messaging.
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Cc: Jens Wiklander <jens.wiklander@linaro.org>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add Arm FF-A support implementing Arm Firmware Framework for Armv8-A v1.0
The Firmware Framework for Arm A-profile processors (FF-A v1.0) [1]
describes interfaces (ABIs) that standardize communication
between the Secure World and Normal World leveraging TrustZone
technology.
This driver uses 64-bit registers as per SMCCCv1.2 spec and comes
on top of the SMCCC layer. The driver provides the FF-A ABIs needed for
querying the FF-A framework from the secure world.
The driver uses SMC32 calling convention which means using the first
32-bit data of the Xn registers.
All supported ABIs come with their 32-bit version except FFA_RXTX_MAP
which has 64-bit version supported.
Both 32-bit and 64-bit direct messaging are supported which allows both
32-bit and 64-bit clients to use the FF-A bus.
FF-A is a discoverable bus and similar to architecture features.
FF-A bus is discovered using ARM_SMCCC_FEATURES mechanism performed
by the PSCI driver.
Clients are able to probe then use the FF-A bus by calling the DM class
searching APIs (e.g: uclass_first_device).
The Secure World is considered as one entity to communicate with
using the FF-A bus. FF-A communication is handled by one device and
one instance (the bus). This FF-A driver takes care of all the
interactions between Normal world and Secure World.
The driver exports its operations to be used by upper layers.
Exported operations:
- ffa_partition_info_get
- ffa_sync_send_receive
- ffa_rxtx_unmap
Generic FF-A methods are implemented in the Uclass (arm-ffa-uclass.c).
Arm specific methods are implemented in the Arm driver (arm-ffa.c).
For more details please refer to the driver documentation [2].
[1]: https://developer.arm.com/documentation/den0077/latest/
[2]: doc/arch/arm64.ffa.rst
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Cc: Tom Rini <trini@konsulko.com>
Cc: Jens Wiklander <jens.wiklander@linaro.org>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Move the ethernet gadget driver registration and removal from ethernet
bind and unbind callbacks into driver DM probe and remove callbacks.
This way, when the driver is bound, which is triggered deliberately
using 'bind' command, the USB ethernet gadget driver is instantiated
and bound to the matching UDC. In reverse, when the driver is unbound,
which is again triggered deliberately using 'unbind' command, the USB
ethernet gadget driver instance is removed.
Effectively, this now behaves like running either 'ums' or 'dfu' or
any other commands utilizing USB gadget functionality.
This also drops use of usb_gadget_release() and moves the use of
usb_gadget_initialize() into usb_ether_init() used only by legacy
platforms that do not use 'bind' command properly yet. Those have
no place in drivers.
Signed-off-by: Marek Vasut <marex@denx.de>
Tested-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move the driver probe function above the driver structure, so it
can be placed alongside other related functions, like upcoming
remove function. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Tested-by: Tom Rini <trini@konsulko.com>
Tested-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
These functions here are only ever called once since drop of non-DM
networking code. Inline them. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Tested-by: Tom Rini <trini@konsulko.com>
Tested-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
If a driver cannot be bound, provide the driver name in the debug
message. Now the debug message may look like this:
(virtio-pci.l#0): virtio-rng driver not configured
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds support for MediaTek MT7988.
MT7988 features MediaTek NETSYS v3, including three GMACs, and two
of them supports 10Gbps USXGMII.
MT7988 embeds a MT7531 switch (not MCM) which supports accessing
internal registers through MMIO instead of MDIO.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
MT7981 has its GMAC2 PHY shared with USB3. To enable GMAC2, mux
register must be set to connect the SGMII phy to GMAC2.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Existing SGMII support of mtk-eth is actually a MediaTek-specific
2.5Gbps high-speed SGMII (HSGMII) which does not support
auto-negotiation mode.
This patch adds SGMII 1Gbps auto-negotiation mode and rename the
existing HSGMII to 2500basex.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
mt7531_mmd_ind_read and mt753x_switch_init are defined without static.
Since they're not used outside this file, we should add them back.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
fixup to add static qualifier
The original direct MDIO clause 45 access via SoC is missing the
data output. This patch adds it back to ensure MDIO clause 45 can
work properly for external PHYs.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Not all switches requires 1 second delay after deasserting reset.
MT7531 requires only maximum 200ms.
This patch defines dedicated reset wait time for each switch chip, and will
significantly improve the boot time for boards using MT7531.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
So far the switch is initialized in probe stage and is connected to PSE
unconditionally. This will cause all packets being flooded to PSE and may
cause PSE hang before entering linux.
This patch changes the connection between switch and PSE:
- Still initialize switch in probe stage, but disconnect it with PSE
- Connect switch with PSE on eth start
- Disconnect on eth stop
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
The original mediatek pinctrl functions for driving configuration
'mtk_pinconf_drive_set_*' do not return -ENOSUPP even if input
parameters are not supported.
This patch fixes the return value in those functions.
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
There exists a situation of the mediatek pinctrl driver that may return
wrong pin function value for the pinmux driver:
- All pin function arrays are defined without const
- Some pin function arrays contain all-zero value, e.g.:
static int mt7622_spi_funcs[] = { 0, 0, 0, 0, 0, 0, };
- These arrays will be put into .bss section during compilation
- .bss section has no "a" attribute and does not exist in the final binary
file after objcopy.
- FDT binary blob is appended to the u-boot binary, which occupies the
.bss section.
- During board_f stage, .bss has not been initialized, and contains the
data of FDT, which is not full-zero data.
- pinctrl driver is initialized in board_f stage, and it will get wrong
data if another driver is going to set default pinctrl.
Since pinmux information and soc data are only meant to be read-only, thus
should be declared as const. This will force all pinctrl data being put
into .rodata section. Since .rodata has "a" attribute, even the all-zero
data will be allocated and filled with correct value in to u-boot binary.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
MT7981 actually uses MediaTek I2C controller v3 instead of v1.
This patch adds support for I2C controller v3 fix fixes the I2C usability
for MT7981.
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch add missing return value check for allocating the driver's
private data. -ENOMEM will be returned if malloc() fails.
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch ensures driver private data being fully initialized in
_debug_uart_init which is not covered by .priv_auto ops.
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Reviewed-by: Stefan Roese <sr@denx.de>
In u-boot we don't use IRQ. Instead, we poll busy bit in SPI_STATUS.
However these IRQ enable bits may be set in previous boot stage (BootROM).
If we leave these bits not cleared, although u-boot has disabled IRQ and
nothing will happen, the linux kernel may encounter panic during
initializing the spim driver due to IRQ event happens before IRQ handler
is properly setup.
This patch clear IRQ bits to prevent this from happening.
Signed-off-by: SkyLake.Huang <skylake.huang@mediatek.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
We don't really need to switch clk rate during operating SPIM controller.
Get clk rate only once at driver probing.
Signed-off-by: SkyLake.Huang <skylake.huang@mediatek.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Add rtl8169 NIC device ID and reorder the device ID.
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
For RISC-V architeture, hardware maintain the dcache coherency.
Software do not flush the cache. So even cache-line size larger
than descriptor size, driver can work.
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
While compiling rtl8169.c, There are many "make pointer from
integer without a cast" compile warnings. fix them with
adding cast.
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Add pcie driver for StarFive JH7110, Also add PLDA
PCIe controller common driver functions.
Several devices are tested:
a) M.2 NVMe SSD
b) Realtek 8169 Ethernet adapter.
Signed-off-by: Mason Huo <mason.huo@starfivetech.com>
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Acked-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
As the Designware_i2c_pci.c uses ACPI APIs, If some SoCs (StarFive
JH7110) contain Designware i2c and PCI but do not use ACPI,
This file cannot be compiled. So add a new Kconfig for
designware_i2c_pci.c, which depends on ACPIGEN
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
- Add a little more info to 'cbsysinfo' command
-----BEGIN PGP SIGNATURE-----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=s8Ab
-----END PGP SIGNATURE-----
Merge tag 'x86-pull-20230801' of https://source.denx.de/u-boot/custodians/u-boot-x86
- MTRR fixes for x86 boards
- Add a little more info to 'cbsysinfo' command
- bochs: remove the x86 limitation
- correct kconfig text for PCI default FB size
- kconfig: drop the superfluous PCI dependency
- set up default FB size for Bochs
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCZMj+xA4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXPovAJ9DU0H3Xm9LmrPZE4NzmmkfKJ/99QCfTlDfIkZI
dVilMWOHsRX1SgMS6YM=
=KYKc
-----END PGP SIGNATURE-----
Merge tag 'video-20230801' of https://source.denx.de/u-boot/custodians/u-boot-video
- dm video cosmetic style fix
- bochs: remove the x86 limitation
- correct kconfig text for PCI default FB size
- kconfig: drop the superfluous PCI dependency
- set up default FB size for Bochs
Perform removal of DSS if kconfigs VIDEO_REMOVE or SPL_VIDEO_REMOVE is
set by user. Otherwise if above Kconfigs are not selected, it is assumed
that user wants splash screen to be displayed until linux kernel boots
up. In such scenario, leave the power domain of DSS as "on" so that
splash screen stays intact until kernel boots up.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
Change remove method of DSS video driver to disable video port instead
of performing a soft reset, as soft reset takes longer duration. Video
port is disabled by setting enable bit of video port to 0.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
At present the uclass stored frame buffer size is set to a hard
coded value, but we can calculate the correct value based on what
is configured.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # qemu-x86_64
Set up a default frame buffer size of 8MiB for Bochs for non-x86
architecturs as PCI is normally not enumerated before relocation
on these architectures.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
PCI is always selected by X86 architecture hence "X86 && PCI" does
not make it better.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # qemu-x86_64
There is an example in the VIDEO_PCI_DEFAULT_FB_SIZE help text to
tell people how to calculate its value but the resolution given
does not match the value. Fix it.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Now that the driver is legacy free, remove the x86 dependency so
that it can be used on non-x86 architectures.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # qemu-x86_64
At present the driver uses IO instructions to access the legacy
VGA IO ports, which unfortunately limits the driver to work only
on x86. It turns out the IO instruction is not necessary as Bochs
VGA card remaps the legacy VGA IO ports (0x3c0 -> 0x3df) to its
memory mapped register space from offset 0x400.
Update the driver to use MMIO access for VGA IO port.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # qemu-x86_64
bochs_vga_write() takes 'index' as one argument, but never uses it.
While we are here, use macros instead of magic numbers for the
VGA IO port register name and value.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # qemu-x86_64
The driver does not call any MTRR APIs.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # qemu-x86_64
Some coding convention fixes for video_post_bind().
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # qemu-x86_64
At present this uses mtrr_add_request() & mtrr_commit() combination
to program the MTRR for graphics memory. This usage has two major
issues as below:
- mtrr_commit() will re-initialize all MTRR registers from index 0,
using the settings previously added by mtrr_add_request() and saved
in gd->arch.mtrr_req[], which won't cause any issue but is unnecessary
- The way such combination works is based on the assumption that U-Boot
has full control with MTRR programming (e.g.: U-Boot without any blob
that does all low-level initialization on its own, or using FSP2 which
does not touch MTRR), but this is not the case with FSP. FSP programs
some MTRRs during its execution but U-Boot does not have the settings
saved in gd->arch.mtrr_req[] and when doing mtrr_commit() it will
corrupt what was already programmed previously.
Correct this to use mtrr_set_next_var() instead.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present this uses mtrr_add_request() & mtrr_commit() combination
to program the MTRR for graphics memory. This usage has two major
issues as below:
- mtrr_commit() will re-initialize all MTRR registers from index 0,
using the settings previously added by mtrr_add_request() and saved
in gd->arch.mtrr_req[], which won't cause any issue but is unnecessary
- The way such combination works is based on the assumption that U-Boot
has full control with MTRR programming (e.g.: U-Boot without any blob
that does all low-level initialization on its own, or using FSP2 which
does not touch MTRR), but this is not the case with FSP. FSP programs
some MTRRs during its execution but U-Boot does not have the settings
saved in gd->arch.mtrr_req[] and when doing mtrr_commit() it will
corrupt what was already programmed previously.
Correct this to use mtrr_set_next_var() instead.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present this uses mtrr_add_request() & mtrr_commit() combination
to program the MTRR for graphics memory. This usage has two major
issues as below:
- mtrr_commit() will re-initialize all MTRR registers from index 0,
using the settings previously added by mtrr_add_request() and saved
in gd->arch.mtrr_req[], which won't cause any issue but is unnecessary
- The way such combination works is based on the assumption that U-Boot
has full control with MTRR programming (e.g.: U-Boot without any blob
that does all low-level initialization on its own, or using FSP2 which
does not touch MTRR), but this is not the case with FSP. FSP programs
some MTRRs during its execution but U-Boot does not have the settings
saved in gd->arch.mtrr_req[] and when doing mtrr_commit() it will
corrupt what was already programmed previously.
Correct this to use mtrr_set_next_var() instead.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- Update dwc3 generic driver and update support for rk3568/rk3328;
- Add boards:
rk3566: Pine64 Quartz64-A/B, SOQuartz on Model A/Blade/CM4-IO
rk3568: Radxa E25 Carrier Board
rk3588: Radxa ROCK5A
- Fixes and updates for chromebook veryon/jerry/speedy;
- SPI support fixes for rk3399/rk3568/rk3588;
- rk3588 usbdp phy support;
- dts and config updates for different boards;
Handle USB480M clock ID in set_rate() and set_parent()
to allow the dt assigned-clocks and assigned-clock-parents
work on rk3328.dtsi
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Sean Anderson <seanga2@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
USB2.0 Host and OTG controllers in RK3328 are using USB2PHY.
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Xavier Drudis Ferran <xdrudis@tinet.cat>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Like Rockchip RK3568, the RK3328 also have single node to
represent the glue and ctrl for USB 3.0.
So, use the driver data to use single ctrl for RK3328 DWC3.
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
A quick power cycle of a LDO regulator during dw-mmc signal voltage
change has shown that SD-card does not always get recognized.
Linux driver use an enable_time of 400us for LDO regulators. Apply a
500us delay when a LDO regulator is enabled to fix possible issues.
Fixes: 94afc1cb46 ("power: regulator: rk8xx: update the driver for rk808 and rk818")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: elaine.zhang<elaine.zhang@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
gpio_request_list_by_name() returns the number of gpios requested.
Notably it swallows the underlying -ENOENT when the "gpios" property
does not exist.
Update the i2c-gpio driver to check for ret == 0 before trying the new
sda-gpios/scl-gpios properties.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
RK3568 share glue and ctrl in a single node. Use glue_get_ctrl_dev to
return the glue node as the ctrl node.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Marek Vasut <marex@denx.de>
When dr_mode is peripheral or otg and U-Boot has not been built with
DM_USB_GADGET support, booting such device may end up with:
dwc3_glue_bind_common: subnode name: usb@fcc00000
Error binding driver 'dwc3-generic-wrapper': -6
Some drivers failed to bind
initcall sequence 00000000effbca08 failed at call 0000000000a217c8 (err=-6)
### ERROR ### Please RESET the board ###
Instead fail gracfully with ENODEV to allow board continue booting.
dwc3_glue_bind_common: subnode name: usb@fcc00000
dwc3_glue_bind_common: unsupported dr_mode 3
Also use CONFIG_IS_ENABLED(USB_HOST) and change switch to if statements
to improve readability of the code.
Fixes: 446e3a205b ("dwc3-generic: Handle the PHYs, the clocks and the reset lines")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Marek Vasut <marex@denx.de>
The current error check for device_find_first_child is not working as
expected, the documentation for device_find_first_child mention:
@devp: Returns first child device, or NULL if none
Return: 0
Change to return early when there is no child node to avoid any possible
null pointer dereference.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
CONFIG_SPL_PCI_PNP=y without CONFIG_SPL_PCI=y makes no sense.
Fixes: 32f5e9e5c1 ("nvme: pci: Enable for SPL")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
- Resync some of the K3 DTS files with the kernel, and pull in some
required related updates to keep drivers in sync with the dts files
now. Bring in some incremental fixes on top of one of the series I
applied recently as well as updating the iot2050 platform. Also do a
few small updates to the K2 platforms.
- Enable pcie support for rk3568;
- Add boards:
rk3399: Radxa ROCK 4SE;
rk3328: Orange Pi R1 Plus, Orange Pi R1 Plus LTS
rk3568: FriendlyARM NanoPi R5S/R5C, Hardkernel ODROID-M1
rk3588: Edgeble Neu6B
- support OP-TEE with binman;
- support Winbond SPI flash;
- rk3588 usbdp phy support;
- dts and config updates for different boards;
The TI AM654 timer is compatible with the omap-timer implementation,
so add it to the compatible id list.
Signed-off-by: Sjoerd Simons <sjoerd@collabora.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Cc: Francesco Dolcini <francesco@dolcini.it>
Cc: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Nishanth Menon <nm@ti.com>
The dwc_ahci driver use platform specific defines, place the platform
specific code behind a ifdef CONFIG_ARCH_OMAP2PLUS to allow build and
use of the driver on Rockchip platform.
Fixes: 02a4b42979 ("drivers: block: dwc_ahci: Implement a driver for Synopsys DWC sata device")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
The commit 12df2c182ccb ("regulator: dt-bindings: fixed-regulator: allow
gpios property") in linux v6.3-rc1 added support for use of either a
gpios or gpio prop with a fixed-regulator.
This adds support for the new gpios prop to the fixed-regulator driver.
gpios prop is used by vcc3v3-pcie-regulator on Radxa ROCK 3 Model A.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Root Complex BARs default to claim the full 1 GiB memory region on
RK3568, leaving no space for any attached device.
Fix this by disable the unused BAR 0 and BAR 1 of the RC.
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
[jonas@kwiboo.se: Move to rk_pcie_configure and use PCI_BASE_ADDRESS_0/1 const]
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Use a similar pattern and delay values as the linux mainline driver to
speed up failing when nothing is connected.
Reduce fail speed from around 5+ seconds down to around one second on a
Radxa ROCK 3 Model A, where pcie2x1 is probed before pcie3x2 M2 slot.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The vpcie3v3 regulator is typically a fixed regulator controlled using
gpio. Change to use enable and disable calls on the regulator instead
of trying to set a voltage value.
Also remove the delay to match linux driver, for a fixed regulator the
startup-delay-us prop can be used in case a startup delay is needed.
Limited testing on ROCK 3A, ROCK 5B, Quartz64, Odroid-M1 has shown that
this delay was not needed.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Get the config region to use from the reg prop. Also update the
referenced region index used in comment.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add dev_read_addr_size_index_ptr function with the same functionality as
dev_read_addr_size_index, but instead a return pointer is given.
Use map_sysmem() function as cast for the return.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Rockchip boot blocks are written per 4 x 512 byte sectors per page.
Each page must have a page address (PA) pointer in OOB to the next page.
Pages are written in a pattern depending on the NAND chip ID.
This logic used to build a page pattern table is not fully disclosed and
is not easy to fit in the MTD framework.
The formula in rk_nfc_write_page_hwecc() function is not correct.
Make hwecc and raw behavior identical.
Generate boot block page address and pattern for hwecc in user space
and copy PA data to/from the already reserved last 4 bytes before EEC
in the chip->oob_poi data layout.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This adds a new USBDP combo PHY with Samsung IP block driver.
The PHY is a combo between USB 3.0 and DisplayPort alt mode.
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
[eugen.hristev@collabora.com: ported to 2023.07, clean-up]
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This just needs some extra clocks enabled, and different registers
configured. Copied from Linux, just like the original submitter
of this driver did for rk3568.
Tested on Pinephone Pro.
Signed-off-by: Ondrej Jirman <megi@xff.cz>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Philipp Tomsich <philipp.tomsich@vrull.eu>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Approved DT binding has the port mode register in the
"phys" property. Get it from there instead of the custom
"cpsw-phy-sel" property.
This will allow us to keep DT in sync with Linux.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Nishanth Menon <nm@ti.com>
The approved DT property for MAC efuse (ROM) address is
"ti,syscon-efuse".
Use that and drop custom property "mac_efuse".
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Nishanth Menon <nm@ti.com>
The binding represents the MDIO controller as a child device tree
node of the MAC device tree node.
The U-Boot driver mostly ignores that child device tree node and just
hardcodes the resources it uses to support both the MAC and MDIO in a
single driver.
However, some resources like pinctrl muxing states are thus ignored.
This has been a problem with some device trees that will put some
pinctrl states on the MDIO device tree node, like the SK-AM62 Device
Tree does.
Let's rework the driver a bit to create a dummy MDIO driver that we will
then get during our initialization to force the core to select the right
muxing.
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Acked-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Nishanth Menon <nm@ti.com>
The adin phy has extended registers that can be accessed using
adin_ext_read and adin_ext_write. These registers can be read directly
using the mdio command using readext and writext. For example:
=> mdio rx ethernet@428a0000 0xff23
Reading from bus ethernet@428a0000
PHY at address 0:
65315 - 0xe01
Signed-off-by: Nate Drude <nate.d@variscite.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Copy and tweak the required code from the linux kernel.
Only the KSZ9893 has been tested.
Signed-off-by: Karsten Wiese <karsten.wiese@protechna.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
drivers/core/device.c will call `device_free()` after xhci_register
already frees the private device data. This can cause a crash later
during the boot process, observed on aarch64 RPi4b as a synchronous
exception. All callers of xhci_register use priv_auto, so this won't
lead to memory leaks.
Signed-off-by: Richard Habeeb <richard.habeeb@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This watchdog driver applies to the following
mcf families:
- mcf52x2 (5271 5275 5282)
- mcf532x (5329 5373)
- mcf523x (5235)
Cpu's not listed for each family does not have WDT module.
Note, after some attempts testing by qemu on 5208 i
finally abandoned, watchdog seems not implemented properly.
The driver has been tested in a real M5282EVM.
Signed-off-by: Angelo Dureghello <angelo@kernel-space.org>
---
Changes for v2:
- remove unnecessary hardcoded timeouts
- remove unnecessary hw_watchdog_xxx stuff
- rewrite wdog module reg calculation
- using IS_ENABLED() where possible
Changes for v3:
- remove hardcoded 4s test
In some designs the MAX313xx RTC may need calibration to cope with
oscillator inaccuracies. Provide read8/write8 ops so that the registers
can be accessed. Because the driver covers a range of MAX313xx variants
no attempt is made to ensure the register is valid.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Commit 62649165cb ("lib: sparse: Make CHUNK_TYPE_RAW buffer aligned")
fixed cache alignment for systems with a D-CACHE.
However it introduced some performance regressions [1] on system
flashing huge images, such as Android.
On AM62x SK EVM, we also observe such performance penalty:
Sending sparse 'super' 1/2 (768793 KB) OKAY [ 23.954s]
Writing 'super' OKAY [ 75.926s]
Sending sparse 'super' 2/2 (629819 KB) OKAY [ 19.641s]
Writing 'super' OKAY [ 62.849s]
Finished. Total time: 182.474s
The reason for this is that we use an arbitrary small buffer
(info->blksz * 100) for transferring.
Fix it by using a bigger buffer (info->blksz * FASTBOOT_MAX_BLK_WRITE)
as suggested in the original's patch review [2].
With this patch, performance impact is mitigated:
Sending sparse 'super' 1/2 (768793 KB) OKAY [ 23.912s]
Writing 'super' OKAY [ 15.780s]
Sending sparse 'super' 2/2 (629819 KB) OKAY [ 19.581s]
Writing 'super' OKAY [ 17.192s]
Finished. Total time: 76.569s
[1] https://lore.kernel.org/r/20221118121323.4009193-1-gary.bisson@boundarydevices.com
[2] https://lore.kernel.org/r/all/43e4c17c-4483-ec8e-f843-9b4c5569bd18@seco.com/
Fixes: 62649165cb ("lib: sparse: Make CHUNK_TYPE_RAW buffer aligned")
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
This driver considers that a node with an empty label is the top.
But the led class has changed, if a label is not provided for a led,
the label is filed with the node name. So we update this driver
to use a wrapper to manage the top led node.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Sec proxy data buffer is 60 bytes with the last of the registers
indicating transmission completion. This however poses a bit of a
challenge.
The backing memory for sec_proxy is regular memory, and all sec proxy
does is to trigger a burst of all 60 bytes of data over to the target
thread backing ring accelerator. It doesn't do a memory scrub when
it moves data out in the burst. When we transmit multiple messages,
remnants of previous message is also transmitted which results in
some random data being set in TISCI fields of messages that have been
expanded forward.
The entire concept of backward compatibility hinges on the fact that
the unused message fields remain 0x0 allowing for 0x0 value to be
specially considered when backward compatibility of message extension
is done.
So, instead of just writing the completion register, we continue
to fill the message buffer up with 0x0 (note: for partial message
involving completion, we already do this).
This allows us to scale and introduce ABI changes back also work with
other boot stages that may have left data in the internal memory.
While at this, drop the unused accessor function.
Fixes: f9aa41023b ("mailbox: Introduce K3 Secure Proxy Driver")
Signed-off-by: Nishanth Menon <nm@ti.com>
This reverts commit d927d1a808, reversing
changes made to c07ad9520c.
These changes do not pass CI currently.
Signed-off-by: Tom Rini <trini@konsulko.com>
Emulate Secure World's FF-A ABIs and allow testing U-Boot FF-A support
Features of the sandbox FF-A support:
- Introduce an FF-A emulator
- Introduce an FF-A device driver for FF-A comms with emulated Secure World
- Provides test methods allowing to read the status of the inspected ABIs
The sandbox FF-A emulator supports only 64-bit direct messaging.
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Cc: Jens Wiklander <jens.wiklander@linaro.org>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Provide armffa command showcasing the use of the U-Boot FF-A support
armffa is a command showcasing how to invoke FF-A operations.
This provides a guidance to the client developers on how to
call the FF-A bus interfaces. The command also allows to gather secure
partitions information and ping these partitions. The command is also
helpful in testing the communication with secure partitions.
For more details please refer to the command documentation [1].
[1]: doc/usage/cmd/armffa.rst
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Cc: Jens Wiklander <jens.wiklander@linaro.org>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add Arm FF-A support implementing Arm Firmware Framework for Armv8-A v1.0
The Firmware Framework for Arm A-profile processors (FF-A v1.0) [1]
describes interfaces (ABIs) that standardize communication
between the Secure World and Normal World leveraging TrustZone
technology.
This driver uses 64-bit registers as per SMCCCv1.2 spec and comes
on top of the SMCCC layer. The driver provides the FF-A ABIs needed for
querying the FF-A framework from the secure world.
The driver uses SMC32 calling convention which means using the first
32-bit data of the Xn registers.
All supported ABIs come with their 32-bit version except FFA_RXTX_MAP
which has 64-bit version supported.
Both 32-bit and 64-bit direct messaging are supported which allows both
32-bit and 64-bit clients to use the FF-A bus.
FF-A is a discoverable bus and similar to architecture features.
FF-A bus is discovered using ARM_SMCCC_FEATURES mechanism performed
by the PSCI driver.
Clients are able to probe then use the FF-A bus by calling the DM class
searching APIs (e.g: uclass_first_device).
The Secure World is considered as one entity to communicate with
using the FF-A bus. FF-A communication is handled by one device and
one instance (the bus). This FF-A driver takes care of all the
interactions between Normal world and Secure World.
The driver exports its operations to be used by upper layers.
Exported operations:
- ffa_partition_info_get
- ffa_sync_send_receive
- ffa_rxtx_unmap
Generic FF-A methods are implemented in the Uclass (arm-ffa-uclass.c).
Arm specific methods are implemented in the Arm driver (arm-ffa.c).
For more details please refer to the driver documentation [2].
[1]: https://developer.arm.com/documentation/den0077/latest/
[2]: doc/arch/arm64.ffa.rst
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Cc: Jens Wiklander <jens.wiklander@linaro.org>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmS+Xv0cHGV1Z2VuLmhy
aXN0ZXZAY29sbGFib3JhLmNvbQAKCRAesx4CDqwvyMgxB/9BTjFfVaglu5+m/kiw
XEVSJSwe1H3sc5vFlMUYTSAOSF/mzdZIZHXC6THkCU1yfzu9AZXhp4mfRUiNTwth
w8bvYXm4ZjSxcGPVxVqfThN8iT/SWLpaUC8j7TosP1VKYwzpGmqLyO+ZLu7IwdH+
/wyXFuYtVQVxmSC6SMNAD5eNtS4O6pufat5e5EkhR2atZ/rhhAYmb9zv3RFuCuSM
bxqM+4/FqpENaIdMOPk7EbB3S1C5MsJS2b+s1oIRRLfItlLjpQG4nZnuJGRlL/Bg
mcqYYgHrAnFbLXVOEe5WxMKR1E2fMbtKSlJGpoYO9rSdQRzxGuyRrDm9M77GH2pJ
0Q/F
=DT1v
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-fixes-2023.10-a' of https://source.denx.de/u-boot/custodians/u-boot-at91
First set of u-boot-atmel fixes for the 2023.07 cycle:
This small fixes set includes the LTO configs for the boards that had
the SPL size up to the limit (sama5d2-based), such that more code can be
added. It also includes a fix for mmc non-removable.
If the device attached to the MMC bus is not removable, set force card-detect
bit to bypass card detection procedure, so card detection pin can be used for
other purposes.
It's also a workaround for SAMA5D2 who doesn't drive CMD if using GPIO for card
detection.
Signed-off-by: Zixun LI <zli@ogga.fr>
Reviewed-by: Eugen Hristev <eugen.hristev@collabora.com>
Drop the PLL part in SYSCRG driver and separate to be a single
PLL driver of which the compatible is "starfive,jh7110-pll".
Signed-off-by: Xingyu Wu <xingyu.wu@starfivetech.com>
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
Reviewed-by: Torsten Duwe <duwe@suse.de>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
This is required since user may want to either call the remove method
of video driver and reset the display or not call the remove method
to continue displaying until next stage.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
U-boot proper can use frame buffer address passed from SPL to reserve
the memory area used by framebuffer set in SPL so that splash image
set in SPL continues to get displayed while u-boot proper is running.
Put the framebuffer address and size in a bloblist to make them
available at u-boot proper, if in u-boot proper CONFIG_VIDEO is defined.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add method to reserve video framebuffer information using blob,
received from previous stage.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
During LPDDR initialization we will loop through a series of frequency
changes in order to train at the various operating frequencies. During
this training, accessing the DRAM_CLASS bitfield could happen during a
frequency change and cause the read to hang.
Store the DRAM type into the main structure to avoid multiple readings
while the independent phy is training.
Signed-off-by: Bryan Brattlof <bb@ti.com>
For once this adds USB support for two SoCs: the H616 and the F1C100s
series. The rest is support for LPDDR3 DRAM chips on H616 boards.
Gitlab CI passed, and I booted that briefly on an H616 and an F1C200s
board. I don't have an H616 board with LPDDR3 DRAM, but reportedly that
works for Mikhail, and doesn't regress on my DDR3 boards.
axi_emac:
- Change return value if RX packet is not ready
cadence_qspi:
- Enable flash reset for Versal NET
dt:
- Various DT syncups with Linux kernel
- SOM - reserved pmufw memory location
fpga:
- Add load event
mtd:
- Add missing dependency for FLASH_CFI_MTD
spi/nand:
- Minor cleanup in Xilinx drivers
versal-net:
- Prioritize boot device in boot_targets
- Wire mini ospi/qspi/emmc configurations
watchdog:
- Use new versal-wwdt property
xilinx:
- fix sparse warnings in various places ps7_init*
- add missing headers
- consolidate code around zynqmp_mmio_read/write
- switch to amd.com email
zynqmp_clk:
- Add handling for gem rx/tsu clocks
zynq_gem:
- Configure mdio clock at run time
zynq:
- Enable fdt overlay support
zynq_sdhci:
- Call dll reset only for ZynqMP SOCs
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCZLqHzgAKCRDKSWXLKUoM
IcdEAKCSgy0lMxb1c0adCjpkQR9x63oKbQCdGiioU+W+0moznHdI7+W2UptNt3w=
=Uzn8
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2023.10-rc1-v2' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2023.10-rc1 v2
axi_emac:
- Change return value if RX packet is not ready
cadence_qspi:
- Enable flash reset for Versal NET
dt:
- Various DT syncups with Linux kernel
- SOM - reserved pmufw memory location
fpga:
- Add load event
mtd:
- Add missing dependency for FLASH_CFI_MTD
spi/nand:
- Minor cleanup in Xilinx drivers
versal-net:
- Prioritize boot device in boot_targets
- Wire mini ospi/qspi/emmc configurations
watchdog:
- Use new versal-wwdt property
xilinx:
- fix sparse warnings in various places ps7_init*
- add missing headers
- consolidate code around zynqmp_mmio_read/write
- switch to amd.com email
zynqmp_clk:
- Add handling for gem rx/tsu clocks
zynq_gem:
- Configure mdio clock at run time
zynq:
- Enable fdt overlay support
zynq_sdhci:
- Call dll reset only for ZynqMP SOCs
This enables implementing custom logic after a bitstream was loaded
into the fpga.
Signed-off-by: Christian Taedcke <christian.taedcke@weidmueller.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Link: https://lore.kernel.org/r/20230720072724.11516-1-christian.taedcke-oss@weidmueller.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add gem_tsu and gem0_rx till gem3_rx to return proper register from
zynqmp_clk_get_register. Otherwise firmware won't be able to set clock
for these due to incorrect register address.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230720072859.3724-1-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
gem0_rx till gem3_rx and gem_tsu are missing from set rate function.
Add them, so that they can be set from pmu firmware via clock framework.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230719084912.30209-1-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
If there is no incoming package than axiemac_recv will return -1 which
in turn leads to printing `eth_rx: recv() returned error -1` error
message in eth_rx function. But missing a package is not an fatal error,
so return -EAGAIN in that case would be more suitable.
Signed-off-by: Maksim Kiselev <bigunclemax@gmail.com>
Link: https://lore.kernel.org/r/20230719065337.69280-1-bigunclemax@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Dll reset is needed only for ZynqMP platforms, add condition in tuning
to call arasan_zynqmp_dll_reset() just for ZynqMP platforms.
On other platforms like Versal NET, If this condition is not added, we
see PLM error messages when dll reset smc is called.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/d673ff3bdc5c236a7f0403c920e719684abd6059.1688991117.git.michal.simek@amd.com
Enable flash reset functionality for Versal NET platform.
In cadence_qspi.c there is weak function defined for reset, hence remove
the check for config, so that it will work for Versal and Versal NET
platforms.
Add register defines in Versal NET hardware.h for mini U-Boot flash
reset.
Add read_delay initialization for Versal NET also.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230614120452.21019-1-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
As per spec MDC must not exceed 2.5MHz, read the pclk clock
from the device tree and update the MDC clock divisor.
GEM devices support larger clock divisors and have a different
range of divisors. Program the MDIO clock divisors based on
the clock rate of the pclk clock.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20230619034922.24019-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
status and ecc_status are of unsigned type where they are compared for
negative value. This is pointed by below sparse warning. Change datatype
to int to fix this.
warning: comparison of unsigned expression in '< 0' is always false
[-Wtype-limits]
Signed-off-by: Algapally Santosh Sagar <santoshsagar.algapally@amd.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230614090359.10809-5-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
When one of the functions does not support super speed, the composite
driver forces the gadget to high speed. But the speed is never
configured in the cdns3 gadget driver. So configure the speed
in cdns3_gadget_udc_start just like in the kernel.
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Remove the regulator_set_enable() call from device probe which
resolves a regulator imbalance. This is unnecessary as
regulator_set_enable() will be called when ehci_register calls the
init_after_reset hook.
Suggested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Now that the Allwinner USB PHY driver supports the H616 quirk, let's
enable support for USB ports on that SoC.
We connect the compatible string to a new struct describing the SoCs USB
PHY properties, and unblock the PHY driver selection in Kconfig.
A later patch will enable USB support in the H616 boards' defconfigs.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
The H616 USB PHY is some kind of special snowflake: Only port2 works out
of the box, but all other ports need some help from this port2 to work
correctly: The CLK_BUS_PHY2 and RST_USB_PHY2 clock and reset need to be
enabled, and the SIDDQ bit in the PMU PHY control register needs to be
cleared. For this register to be accessible, CLK_BUS_ECHI2 needs to be
ungated. Don't ask ....
Follow the respective Linux patch (b45c6d80325b) and add a quirk bit,
triggering the special sequence as outlined above, for PHYs other than
PHY2: ungate this one special clock, and clear the SIDDQ bit. We also
pick the clock and reset from PHY2 and enable them as well.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
So far we were assigning some crude "type" (SoC name, really) to each
Allwinner USB PHY model, then guarding certain quirks based on this.
This does not only look weird, but gets more or more cumbersome to
maintain.
Remove the bogus type names altogether, instead introduce flags for each
quirk, and explicitly check for them.
This improves readability, and simplifies future extensions.
Port of Linux patch 8dd256bae653.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
At the moment we use "select" in each Allwinner SoC's Kconfig section to
include the USB PHY driver in the build. This means it cannot be disabled
via Kconfig, although USB is not really a strictly required core
functionality, and a particular board might not even include USB ports.
Rework the Kconfig part by removing the "select" lines for each SoC's
section, and instead letting it default to "y" in the PHY driver section
itself. We use "depends on !" to exclude the few SoCs we don't support
(yet). The Allwinner V3s does not enable USB (PHY) support at the moment,
even though it should work: let the PHY default to "n" to keep the
current behaviour.
Also the MUSB USB driver directly calls some functions from the PHY
driver, so let the former depend on the PHY driver.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Tested-by: Sam Edwards <CFSworks@gmail.com>
The Allwinner F1C100s implements a single USB PHY, connected to its MUSB
OTG controller. The USB PHY is of the simpler, older type (like the A10),
the only real difference is that it's indeed only one PHY.
Add a struct describing those F1C100s USB PHY properties, and connect it
to the new compatible string.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
In its of_xlate() function, the Allwinner USB PHY driver compares the
args_count variable against the number of implemented USB PHYs, although
this is the *number of arguments* to the DT phandle property. Per the DT
binding for this PHY device, this number is always one, so this check
will always fail if the particular SoC implements exactly one USB PHY.
So far this affected only the V3s (which has USB support disabled), but
the F1C100s also sports one PHY only.
Fix that check to compare args_count against exactly 1, and the args[0]
content (requested PHY number) against the number of implemented PHYs.
This fixes USB operation on the Allwinner V3s and allows to enable USB
on the Allwinner F1C100s SoC.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
The behaviour of dev_read_addr_size() is surprising as it does not
handle #address-cells and #size-cells but instead hardcodes the values
based on sizeof(fdt_addr_t).
This is different from dev_read_addr_size_index() and
dev_read_addr_size_name() both of which do read the cell sizes from the
device tree.
Since dev_read_addr_size() is only used by a single driver and this
driver is broken when CONFIG_FDT_64BIT does not match the address size
in the device tree, fix the function to behave like all of the other
similarly named functions. Drop the property name argument as the only
caller passes "reg" and this is the expected property name matching the
other similarly named functions.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # chromebook_jerry
Tested-by: Simon Glass <sjg@chromium.org> # chromebook_bob
of_property_match_string calls of_find_property to search for the
string property.
If the device node does not exist, of_find_property returns NULL, and
of_property_match_string returns -EINVAL, which is correct.
However, if the device node exists, but the property is not found,
of_find_property still returns NULL, but it will place -FDT_ERR_NOTFOUND
in the *lenp variable.
of_property_match_string does not use the lenp parameter, thus this error
case is being lost, and treated as if the node is NULL, and returns
-EINVAL, which is incorrect.
The callers of of_property_match_string treat the error differently if
the return value is -EINVAL or -ENOENT, e.g. in dwc3 driver:
ret = generic_phy_get_by_name(dev, "usb3-phy", &phy);
if (!ret) {
ret = generic_phy_init(&phy);
if (ret)
return ret;
} else if (ret != -ENOENT && ret != -ENODATA) {
debug("could not get phy (err %d)\n", ret);
return ret;
} else {
phy.dev = NULL;
}
So the caller drivers will just consider the property missing if -ENOENT
is returned, versus the case of -EINVAL, which means something else.
To fix this situation, changed the code to call the of_find_property
with the right third argument to catch this error code and treat it
accordingly.
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Set MMC clock when reverting to safe bus mode and speed
in case current MMC mode fails. Otherwise, trying out
the other modes may fail as well.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
[hp: fallback to legacy_speed]
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
When tuning command (CMD21) fails with command error, call
mmc_send_stop_transmission() to send stop command (CMD12).
Reviewed-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Add dev_dbg() message in case tuning abort fails
Move tuning opcode check from mmc_abort_tuning()]
Reviewed-by: Peng Fan <peng.fan@nxp.com>
If a tuning command times out, the card could still be processing it,
which will cause problems for recovery. The eMMC specification section
6.6 Data transfer mode (cont’d) claims that CMD12 can be used to stop
CMD21:
"
The relationship between the various data transfer modes is summarized (see Figure 27):
- All data read commands can be aborted any time by the stop command (CMD12).
The data transfer will terminate and the Device will return to the Transfer State.
The read commands are: ... send tuning block (CMD21) ....
"
Add a function that does that.
Based on Linux commit [1] and [2].
[1] e711f0309109 ("mmc: mmc: Introduce mmc_abort_tuning()")
[2] 21adc2e45f4e ("mmc: Improve function name when aborting a tuning
cmd")
Reviewed-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Update commit message, quote relevant part of the specification.
Rename to mmc_send_stop_transmission().
Remove tuning opcode check, this is controller driver specific.
Deduplicate part of mmc_read_blocks() using this function.]
Reviewed-by: Peng Fan <peng.fan@nxp.com>
For MMC/eMMC, the MMC_CMD_STOP_TRANSMISSION response is R1 for read
transfers and R1b for write transfers per JEDEC Standard No. 84-B51
Page 126 . The response is R1b unconditionally per Physical Layer
Simplified Specification Version 9.00.
Correct the response type and add a comment about it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
When CONFIG_CMD_MMC and CONFIG_MMC are disabled, still some compilation
errors are seen as below due to unresolved symbols.
drivers/dfu/dfu_mmc.o: in function `mmc_block_op':
drivers/dfu/dfu_mmc.c:32: undefined reference to `find_mmc_device'
drivers/dfu/dfu_mmc.c:54: undefined reference to `mmc_get_blk_desc'
drivers/dfu/dfu_mmc.c:67: undefined reference to `mmc_get_blk_desc'
drivers/dfu/dfu_mmc.c:70: undefined reference to `mmc_get_blk_desc'
drivers/dfu/dfu_mmc.o: in function `dfu_fill_entity_mmc':
drivers/dfu/dfu_mmc.c:369: undefined reference to `find_mmc_device'
drivers/dfu/dfu_mmc.c:376: undefined reference to `mmc_init'
drivers/dfu/dfu_mmc.c:403: undefined reference to `mmc_get_blk_desc'
gnu/aarch64/lin/aarch64-linux/bin/aarch64-linux-gnu-ld.bfd: line 4:
31661 Segmentation fault (core dumped) $CC --sysroot=$LIBC
--no-warn-rwx-segment "$@"
Makefile:1760: recipe for target 'u-boot' failed
make: *** [u-boot] Error 139
make: *** Deleting file 'u-boot'
Add dependency of CONFIG_MMC for CONFIG_DFU_MMC config to fix the errors.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Bochs is convenient with QEMU on x86 since it does not require a video
BIOS. Add a driver for it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Move from using debug() to log_debug() so that we don't have to use the
__func__ parameter and can access other logging features.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The ACPI tables are special in that they are passed to EFI as a separate
piece, independent of other tables.
Also they can be spread over two areas of memory, e.g. with QEMU we end
up with tables kept in high memory as well.
Add new global_data fields to hold this information and update the bdinfo
command to show the table areas.
Move the rom_table_end variable into the loop that uses it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
In some cases the video ROM may have been enabled previously, such as by
a previous firmware stage. Use the correct address in that case.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
A hex value is expected for the VGA mode. Add a 0x prefix, since the #
construct is not supported in SPL. We don't want to add it, due to
code-size constraints.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When video is set up in SPL, U-Boot proper needs to use the correct
parameters so it can write to the display.
Put these in a bloblist so they are available to U-Boot proper.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
With qemu-x86_64 we need to run the video BIOS while in 32-bit mode, i.e.
SPL. Add a Kconfig option for this, adjust the Makefile rules and use
CONFIG_IS_ENABLED() where needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When running the ROM the code is not very helpful when something goes
wrong. Add a little more debugging and some logging of return values to
improve this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Allow PCI autoconfig to be handled in SPL, so that we can set it up
correctly for boards which need to do this before U-Boot proper. This
includes qemu-x64_64 which needs to set up the video device while in
32-bit mode.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When scanning fails it is useful to be able to decode what went wrong. Add
some debugging for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Once the ACPI tables have been set up, record their address so that it is
possible to list them with 'acpi list'.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This is always zero in the source tree, so drop it.
While we are here, add a comment to _X86EMU_env since the symbol is
actually defined twice, which can cause confusion when building.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The Kconfig for this is currently inside a particular board. Move it into
the correct place and allow use in SPL, so that video can be used there
if needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
It seems better to call this a 'bootdev' since this is name used in the
documentation. The older 'Bootdevice' name is no-longer used and may cause
confusion with the 'bootdevice' environment variable.
Update throughout to use bootdev.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Instead of using the hard-coded value of 0x1f, use 'TASK_TAG'
macro instead to construct the ucd_req_ptr->header.dword_0
This is in sync with what the Linux UFS driver does, i.e.
set the byte0 equal to TASK_TAG (see [1]).
Setting it to a fixed value of 0x1f is wrong as we define
TASK_TAG as 0 inside u-boot ufs framework. So, instead we
should use the macro value directly.
[1]. https://github.com/torvalds/linux/blob/master/drivers/ufs/core/ufshcd.c#L2705
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
This driver considers that a node with an empty label is the top.
But the led class has changed, if a label is not provided for a led,
the label is filed with the node name. So we update this driver
to use a wrapper to manage the top led node.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
The different CPSW sub-system Ethernet ports have different PHY mode
control registers. In order to allow the modes to get configured
independently only the register for the port in question must be
accessed, otherwise we would just be re-configuring the mode for port 1,
while leaving all others at their power-on defaults. Fix this issue by
adding a port-number based offset to the mode control base register
address based on the fact that the control registers for the different
ports are spaced exactly 0x4 bytes apart.
Fixes: 9d0dca1199 ("net: ethernet: ti: Introduce am654 gigabit eth switch subsystem driver")
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
scmi_to_linux_errno() is set to return an appropriate errno
which corresponds to a given SCMI status code.
But the current implementation always returns the same value.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Without CONFIG_CLK, the build fails with the following message:
LD u-boot
aarch64-none-linux-gnu-ld.bfd: drivers/firmware/scmi/scmi_agent-uclass.o: \
in function `scmi_bind_protocols':
.../drivers/firmware/scmi/scmi_agent-uclass.c:79: undefined reference to \
`_u_boot_list_2_driver_2_scmi_clock'
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
This was brought in in 2016 and a number of changes have been made since
then. There does not seem to be much change in functionality, but it is
a good idea to update from time to time.
Bring in the latest version:
5736b15 ("re-add perlin noise again")
Add a few necessary functions, with dummies in some cases. Update the tests
as there are subtle changes in rendering, perhaps not for the better.
Signed-off-by: Simon Glass <sjg@chromium.org>
For laying out text accurately it is necessary to know the width and
height of the text. Add a measure() method to the console API, so this
can be supported.
Add an implementation for truetype and a base implementation for the
normal console.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is sometimes necessary to highlight some text in a different colour.
Add an easy way to do this and then restore the original console colours.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present livetree can only be used for the control FDT. It is useful
to be able to use the ofnode API for other FDTs, e.g. those used by
the upcoming configuration editor.
We already have most of the support present, and tests can be marked with
the UT_TESTF_OTHER_FDT flag to use another FDT as a special case. But
with this change, the functionality becomes more generally available.
Plumb in the require support.
Signed-off-by: Simon Glass <sjg@chromium.org>
The putc_xy() method is supposed to return the amount of space used. The
existing implementation erroneously adds the previous sub-pixel position
to the returned value. This spaces out the characters very slightly more
than it should. It is seldom noticeable but it does make accurate
measurement of the text impossible.
Fix this minor but long-standing bug.
Fixes: a29b012037 ("video: Add a console driver that uses TrueType fonts")
Signed-off-by: Simon Glass <sjg@chromium.org>
This is useful when the background colour must be written before text
is updated, to avoid strange display artifacts.
Add a function for this, using the existing code from the truetype
console.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present there are various restrictions on the use of livetree:
- It is only available once the tree is unflattened, i.e. after relocation
- It is designed to be used with the control FDT
- It can (in principle) be used with other FDTs, but only if they are
unflattened first; this is not supported
Add a few checks to make sure that any tree that is created is actually
valid. Otherwise it can be confusing when nodes and properties cannot
actually be accessed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Devices do not necessarily have nodes attached to them, since they can be
created from platdata. In SPL a devicetree may in fact not exist at all.
Check the node before using it. This avoids failure when OF_CHECKS is
enabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: 5fc7cf8c8e ("gpio: add gpio-hog support")
Reviewed-by: Heiko Schocher <hs@denx.de>
Use proper register base and access method to access GRF registers.
GRF registers start at a completely different base, and need special
access method, that sets the change mask in the 16 MSBs.
Signed-off-by: Ondrej Jirman <megi@xff.cz>
If phy is not defined in DT (eg. on rk3399), generic_phy_get_by_name
will return -ENODATA. Handle that case correctly.
Signed-off-by: Ondrej Jirman <megi@xff.cz>
pllref_clk is unused after being retrieved. fin needs to be set
to dsi->ref clock's rate for the following calculation to work.
Otherwise fin is undefined, and calculation return bogus number
based on undefined variable.
Signed-off-by: Ondrej Jirman <megi@xff.cz>
&priv->phy is always true. Compiler warns about this loudly.
Use a propper check for phy device allocation. Without this fix
using this driver with SoC that doesn't use external phy (eg. RK3399)
doesn't work.
Signed-off-by: Ondrej Jirman <megi@xff.cz>
These must be read from timings->flags, like other DSI HOST drivers do.
And they must not be inverted either. Low means low.
Without this fix, panel drivers that set *SYNC_LOW produce corrupted
output on screen (shifted horizontally and vertically by back porch
distance).
Signed-off-by: Ondrej Jirman <megi@xff.cz>
The intermediate value could overflow for large periods and levels.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The driver is for panels based on the Himax HX8394 controller, such as the
HannStar HSD060BHW4 720x1440 TFT LCD panel that uses a MIPI-DSI interface.
This panel is used in Pinephone Pro.
Signed-off-by: Ondrej Jirman <megi@xff.cz>
Cc: Anatolij Gustschin <agust@denx.de>
Some callers expect to call this with NULL font name to select the
default font (eg. boot/scene.c). Without handling the NULL condition
U-Boot crashes instead of displaying a bootflow GUI menu.
Signed-off-by: Ondrej Jirman <megi@xff.cz>
Cc: Anatolij Gustschin <agust@denx.de>
There are some newer clocks added to the kernel recently,
so to fix prepare for resycing the device trees, update
the clock list. Since there are some minor changes to
the USB clocks, update which USB clocks are enabled
to match with the upstream kernel as well.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Tested-by: Tim Harvey <tharvey@gateworks.com> #imx8mp-venice-gw74xx
On the imx8ulp A1 SoC, the ELE RNG needs to be manually started.
Signed-off-by: Clement Faure <clement.faure@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Extend the RX timeout value to 10s, because when authentication is failed
the ELE needs long time (>2s for 28M image) to return the result. Print
rx wait info per 1s.
Also correct TX and RX status registers in debug.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
According to SRM, the Sentinel MU has 8 TR and 4 RR registers. All
of them are used for ELE message. So update TR count to 8 and fix a
typo in receive msg
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add two ELE API: ele_return_lifecycle_update and ele_write_secure_fuse
Add two cmd: ahab_return_lifecycle and ahab_sec_fuse_prog
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Per NXP requirement, we rename all the NXP EdgeLock Secure Enclave
code including comment, folder and API name to ELE to align.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add support for Winbond 256M-bit flash w25q256jwm.
Performed basic erase/write/readback operations on
ZynqMP zc1751+dc1 board.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
If cs gpio is requested with ACTIVE_HIGH flag, it will
be pulled low(i.e. active). This is not what we expected.
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
XTX changed full company name from "XTX Technology (Shenzhen) Limited
to "XTX Technology Limited" since 2020,So remove "(Shenzhen)".
Signed-off-by: Bruce Suen <bruce_suen@163.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
According to Documentation/devicetree/bindings/spi/spi-gpio.yaml
from Linux, the recommended spio-gpio properties are:
sck-gpios, miso-gpios and mosi-gpios.
gpio-sck, gpio-mosi and gpio-miso are considered deprecated.
Currently, U-Boot only supports the deprecated properties.
Allow the soft_spi driver to support both the new and old properties.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Current code expects that SPI_TX_BYTE is single bit mode
but it is wrong. It indicates byte program mode,
not single bit mode.
If SPI_TX_DUAL, SPI_TX_QUAD and SPI_TX_OCTAL bits are not set,
the default transfer bus width is single bit.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The newer BCMBCA SoCs such as BCM6756, BCM4912 and BCM6855 include an
updated SPI controller that add the capability to allow the driver to
control chip select explicitly. Driver can control and keep cs low
between the transfers natively. Hence the dummy cs workaround or prepend
mode found in the bcm63xx-hsspi driver are no longer needed and this new
driver is much cleaner.
Port from linux patch:
Link: https://lore.kernel.org/r/20230209200246.141520-15-william.zhang@broadcom.com
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Due to the controller limitation to keep the chip select low during the
bus idle time between the transfer, a dummy cs workaround was used when
this driver was first upstreamed to the u-boot based on linux kernel
driver. It basically picks the dummy cs as !actual_cs so typically dummy
cs is 1 when most of the case only cs 0 is used in the board design.
Then invert the polarity of both cs and tell the controller to start the
transfers using dummy cs. Assuming both cs are active low before the
inversion, effectively this keeps dummy cs high and actual cs low during
the transfer and workaround the issue.
This workaround requires that dummy cs 1 pin to is set to SPI chip
selection function in the pinmux when the transfer clock is above 25MHz.
The old chips likely have default pinmux set to chip select on the dummy
cs pin so it works but this is not case for the new Broadband BCA chips
and this workaround stop working. This is specifically an issue to
support SPI NAND and SPI NOR flash because these flash devices can
typically run at or above 100MHz.
This patch utilizes the prepend feature of the controller to combine the
multiple transfers in the same message to a single transfer when
possible. This way there is no need to keep clock low between transfers
and solve the issue without any pinmux requirement.
Multiple transfers within a SPI message may be combined into one
transfer if the following are all true:
* One or more half duplex write transfer in single bit mode
* Optional full duplex read/write at the end
* No delay and cs_change between transfers
Most of the SPI device meets this requirements such as SPI NOR, SPI NAND
flash, Broadcom SPI voice card and etc. So this change switches to the
prepend mode as the default mode. For any SPI message that does not meet
the above requirement, we switch to original dummy cs mode but limit the
clock rate to the safe 25MHz.
Port from linux patch:
Link: https://lore.kernel.org/r/20230209200246.141520-12-william.zhang@broadcom.com
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
New compatible string brcm,bcmbca-hsspi-v1.0 is introduced based on
dts document brcm,bcm63xx-hsspi.yaml. Add it to the driver to support
this new binding.
Port from linux patch:
Link: https://lore.kernel.org/r/20230207065826.285013-6-william.zhang@broadcom.com
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Currently the driver always sets the controller to dual data bit mode
for both tx and rx data in the profile mode control register even for
single data bit transfer. Luckily the opcode is set correctly according
to SPI transfer data bit width so it does not actually cause issues.
This change fixes the problem by setting tx and rx data bit mode field
correctly according to the actual SPI transfer tx and rx data bit width.
Fixes: 29cc4368ad ("dm: spi: add BCM63xx HSSPI driver")
Port from linux patch:
Link: https://lore.kernel.org/r/20230209200246.141520-11-william.zhang@broadcom.com
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
