For SOM with the EC configuration, the ethernet PHY is located on the
SOM itself, and connected to the CPU ethernet controller. It has a
reset line controlled via GPIO1_IO9. In this configuration, the PHY
located on the carrier board is not connected to anything and is
therefore not used.
For SOM without EC configuration, the ethernet PHY on the carrier
board is connected to the CPU ethernet controller. It has a reset line
controlled via the GPIO expander PCA9534_IO5.
The hardware configuration (EC) is determined at runtime by
reading from the SOM EEPROM.
To support both hardware configurations (EC and non-EC), adjust/fix
the PHY reset gpios according to the hardware configuration
read at runtime from the SOM EEPROM. This adjustement is done in
U-Boot (OF_BOARD_FIXUP) and kernel (OF_BOARD_SETUP) device trees.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
In case the i.MX8M Plus starts from eMMC BOOT1/BOOT2 HW partitions, the
flash.bin container is stored at offset 0 from the start, that means the
fitImage itb is at offset 0x2c0 instead of 0x300 sectors from the start.
Handle this difference in custom spl_mmc_get_uboot_raw_sector() .
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
In order to enable HAB, FSL_CAAM, ARCH_MISC_INIT and
SPL_CRYPTO should be enabled in Kconfig like other i.MX8M
boards.
This also needs to occur in the SPL so enable CONFIG_SPL_BOARD_INIT and
add a void spl_board_init function which calls arch_misc_init to probe
the CAAM driver.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Update RAM Timings for 2GB RAM based on DDR Controller Configuration
Spreadsheet revision 22. Including the update of the refresh
rate to workaround errata ERR050805.
Signed-off-by: Cem Tenruh <c.tenruh@phytec.de>
The current bootaux supports i.MX8M and i.MX93, but the name "_M4_"
implies that the SoCs have Cortex-M4. Actually i.MX8MM/Q use Cortex-M4,
i.MX8MN/P use Cortex-M7, i.MX93 use Cortex-M33, so use "_MCU_" in place
of "_M4_" to simplify the naming.
Signed-off-by: faqiang.zhu <faqiang.zhu@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
On the imx8ulp A1 SoC, the ELE RNG needs to be manually started.
Signed-off-by: Clement Faure <clement.faure@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Per NXP requirement, we rename all the NXP EdgeLock Secure Enclave
code including comment, folder and API name to ELE to align.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The return value is int type, not sc_err_t(u8), correct the usage.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Oliver Graute <oliver.graute@kococonnector.com>
Reviewed-by: Oliver Graute <oliver.graute@kococonnector.com>
The return value is int type, not sc_err_t(u8), correct the usage.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Oliver Graute <oliver.graute@kococonnector.com>
Reviewed-by: Oliver Graute <oliver.graute@kococonnector.com>
Running a memtest in U-Boot and Linux shows that some Colibri iMX6
produce bitflips at temperatures above 60°C. This happens because the
RALAT and WALAT values on the Colibri iMX6 are too low. The problems
were introduced by commit 09dbac8174 ("mx6: ddr: Restore ralat/walat
in write level calibration") before the calibration process overwrote
the values and set them to the maximum value. With this commit, we make
sure that the RALAT and WALAT values are set to the maximum values
again. This has been proven to work for years.
Fixes: 09dbac8174 ("mx6: ddr: Restore ralat/walat in write level calibration")
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
The serial clock is provided by the get_serial_clock() callback on PPC
under DM_SERIAL. Use the same method to compute the clock as for
non-DM_SERIAL use cases.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Call pci_init() to force PCI enumeration at probe time.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The serial clock is provided by the get_serial_clock() callback on PPC
under DM_SERIAL. Use the same method to compute the clock as for
non-DM_SERIAL use cases.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Call pci_init() to force PCI enumeration at probe time.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The serial clock is provided by the get_serial_clock() callback on PPC
under DM_SERIAL. Use the same method to compute the clock as for
non-DM_SERIAL use cases.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Call pci_init() to force PCI enumeration at probe time.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The serial clock is provided by the get_serial_clock() callback on PPC
under DM_SERIAL. Use the same method to compute the clock as for
non-DM_SERIAL use cases.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Call pci_init() to force PCI enumeration at probe time.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add support for Sipeed's Lichee Pi 4A board which based on T-HEAD's
TH1520 SoC, only minimal device tree and serial console are enabled,
so it's capable of chain booting from T-HEAD's vendor u-boot.
Reviewed-by: Wei Fu <wefu@redhat.com>
Signed-off-by: Yixun Lan <dlan@gentoo.org>
As the RISC-V ACLINT specification is defined to be backward compatible
with the SiFive CLINT specification, we rename SiFive CLINT to RISC-V
ALINT in the source tree to be future-proof.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Rick Chen <rick@andestech.com>
The main difference between StarFive VisionFive 2 1.2A and 1.3B is gmac.
You can read the PCB version of the current board by
get_pcb_revision_from_eeprom(), and then dynamically configure the
difference of gmac in spl_perform_fixups() according to different PCB
versions, so that one DT and one defconfig can support both 1.2A and
1.3B versions, which is more user-friendly.
Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Enabled ID_EEPROM and I2C configuration for StarFive VisionFive2 board.
Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
Reviewed-By: Leo Yu-Chi Linag <ycliang@andestech.com>
The Gateworks imx8mp-venice-gw7905-2x consists of a SOM + baseboard.
The GW702x SOM contains the following:
- i.MX8M Plus SoC
- LPDDR4 memory
- eMMC Boot device
- Gateworks System Controller (GSC) with integrated EEPROM, button
controller, and ADC's
- PMIC
- SOM connector providing:
- eQoS GbE MII
- 1x SPI
- 2x I2C
- 4x UART
- 2x USB 3.0
- 1x PCI
- 1x SDIO (4-bit 3.3V)
- 1x SDIO (4-bit 3.3V/1.8V)
- GPIO
The GW7905 Baseboard contains the following:
- GPS
- microSD
- off-board I/O connector with I2C, SPI, GPIO
- EERPOM
- PCIe clock generator
- 1x full-length miniPCIe socket with PCI/USB3 (via mux) and USB2.0
- 1x half-length miniPCIe socket with USB2.0 and USB3.0
- USB 3.0 HUB
- USB Type-C with USB PD Sink capability and peripheral support
- USB Type-C with USB 3.0 host support
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Since U-Boot builds HTML documentation, migrate the contents
of the README file to an rst file which can generate the
proper outputs.
Signed-off-by: Adam Ford <aford173@gmail.com>
Instead of cluttering up a header file with a bunch of defines,
move the default environmental variables to a file called
imx8mn_beacon.env and reference it from the defconfigs.
Signed-off-by: Adam Ford <aford173@gmail.com>
Since U-Boot builds HTML documentation, migrate the contents
of the README file to an rst file which can generate the
proper outputs.
Signed-off-by: Adam Ford <aford173@gmail.com>
Instead of cluttering up a header file with a bunch of defines,
move the default environmental variables to a file called
imx8mm_beacon.env and reference it from the defconfig.
Signed-off-by: Adam Ford <aford173@gmail.com>
Enable support to read and display configuration/manufacturing infos
from 4Kbit EEPROM located on SOM board.
Note: CONFIG_DISPLAY_BOARDINFO is automatically selected for ARM arch.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
The in-spl enabled DM serial console requires the board setup to be
able to parse SPL_OF_PLATDATA based serial driver (pl01x) for the
imx28 based XEA board.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This code fixes following WARNING:
DTOC spl/dts/dt-plat.c
fsl_imx28_clkctrl: WARNING: the driver fsl_imx28_clkctrl was not found in the driver list
As imx28 doesn't yet support common clock framework, this prevents from
DTOC warnings during SPL build.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Add new i.MX 8M Plus Quad SKU to ConfigBlock handling.
0070: Verdin iMX8M Plus Quad 8GB WB IT
This SKU is identical to 0066 but supporting Industrial Temperature range.
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
The update_firmware script is intended to update the boot firmware but
the details including the offset and hardware partition are dependent
on the boot device.
Specifically:
- IMX8MM/IMX8MP (BOOTROM v2) the offset is 32KiB for SD and eMMC user
hardware partition and 0KiB for eMMC boot partitions.
- IMX8MM the offset is 33KiB for SD and eMMC regardless of hardware
partition.
Dynamically set soc, dev, bootpart, and bootblk env vars at runtime
and use these in the update_firmware script. Remove the splblk env var
from config files as its no longer needed.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Determine the U-Boot env hardware partition depending on the boot
device.
This allows the same boot firmware image to be placed on user, boot0,
or boot1 without changing CONFIG_SYS_MMC_ENV_PART.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR needs to adjust for
IMX8MN and IMX8MP when booting from an eMMC boot partition due
to IMX BOOTROM v2 using an SPL offset of 0 for boot partitions
and 32K for the user partition.
In order to allow the same firmware to run on both user and boot
hardware partitions adjust raw_sect dynamically at runtime.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The imx8mm_beacon SOM has a QSPI part attached to the FSPI controller.
Update the header and spl files to support booting from NOR flash and
add imx8mm_beacon_fspi_defconfig to support this configuration.
Signed-off-by: Adam Ford <aford173@gmail.com>
The dts sync from Linux leaves mac0/ethernet1 enabled on icicle, but
U-Boot does not currently set a mac address for it. Expand on the code
which currently sets the mac for mac1/ethernet0 to optionally set the
mac address for the second ethernet.
Reviewed-by: Padmarao Begari <padmarao.begari@microchip.com>
Tested-by: Padmarao Begari <padmarao.begari@microchip.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
For changing the USB OTG node status from "okay" to "disabled" more
space is needed, so call fdt_increase_size() to avoid the following
error:
```
U-Boot 2023.07-rc5-0.0.0-devel+git.580eb31199be (Jun 27 2023 - 13:39:58 +0000)
CPU: Freescale i.MX7S rev1.2 800 MHz (running at 792 MHz)
CPU: Extended Commercial temperature grade (-20C to 105C) at 30C
Reset cause: POR
DRAM: initcall sequence 8786eafc failed at call 8781b351 (err=-3)
### ERROR ### Please RESET the board ###
```
Ideally, fdt_status_disabled() should call fdt_increase_size() internally,
so that there would be no need for manually calling it in board code.
Do it manually for now to fix the regression.
Based on the code from board/CZ.NIC/turris_omnia/turris_omnia.c.
Reported-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Tested-by: Francesco Dolcini <francesco.dolcini@toradex.com> # Toradex Colibri iMX7S
The HTC One X is a touchscreen-based, slate-sized smartphone
designed and manufactured by HTC that runs the Android operating
system. The One X features a 4.7" display, an Nvidia Tegra 3
quad-core chip, 1 GB of RAM and non-extendable 32 GB of internal
storage. UART-A is default debug port.
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com>
Tested-by: Ion Agorria <ion@agorria.com>
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
LG X3 is a development board based on Nvidia Tegra 3 SoC
on base of which Optimus 4X HD and Optimus Vu were created.
Both smartphones feature a 4.7" and 5" panels respectively,
an Nvidia Tegra 3 quad-core chip, 1 GB of RAM and 16/32 GB
of internal storage. Optimux 4X HD additionally has a micro
SD slot.
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # LG P880 T30
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # LG P895 T30
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Nexus 7 is a mini tablet computer co-developed by Google and Asus
that runs the Android operating system. The Nexus 7 features a 7"
display, an Nvidia Tegra 3 quad-core chip, 1 GB of RAM and 8/16 GB
of internal storage.
This patch brings support for all 3 known ASUS/Google devices:
- Nexus 7 (2012) E1565
- Nexus 7 (2012) PM269
- Nexus 7 (2012) 3G - tilapia
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # ASUS Grouper E1565
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # ASUS Grouper E1565
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The ASUS Transformer T30 family are 2-in-1 detachable tablets
and AiO developed by ASUS that run the Android operating system
(TF600T runs Windows RT and P1801-T runs Android and Windows).
The T30 Transformers feature a 10.1-inch display (apart P1801-T),
an Nvidia Tegra 3 quad-core chip, 1/2 GB of RAM, and 16/32 GB of
storage. Transformers board derives from Nvidia Cardhu development
board.
This patch brings support for 7 known Transformer devices:
- ASUS Transformer Prime TF201
- ASUS Transformer Pad TF300T/TF300TG/TF300TL
- ASUS VivoTab RT TF600T (Windows RT based)
- ASUS Transformer Infinity TF700T
- ASUS Portable AiO P1801-T
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # all devices
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
board_mmc_get_env_part() is not called as the default implementation
of mmc_get_env_part() is used.
Fix this problem by directly calling mmc_get_env_part() instead.
Signed-off-by: Eduard Strehlau <eduard@lionizers.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
This fixes access to camera sensor over I2C during probe time in
the kernel. (Kernel will fix I/0 port voltage by itself, but the
timing depends on probe order of the drivers, so the fix can
come after the camera sensor driver already failed to probe.)
Signed-off-by: Ondrej Jirman <megi@xff.cz>
Cc: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Add configurations for the Videostrong KII Pro set-top box.
This defconfig is cloned from the WeTek Play2's.
Signed-off-by: Ferass El Hafidi <vitali64pmemail@protonmail.com>
Link: https://lore.kernel.org/r/20230507124109.31778-3-vitali64pmemail@protonmail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
The AD401 board is the Amlogic A1 SoC reference board
Signed-off-by: Igor Prusov <ivprusov@sberdevices.ru>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230505125639.3605-6-ivprusov@sberdevices.ru
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Two conflicting bootcmds were included in the environment.
Streamline to defining the bootcmd only in the env file.
Signed-off-by: Eduard Strehlau <eduard@lionizers.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Enable the newest features: nvmxip, fwu-metadata and
gpt. Commands to print the partition info, gpt info
and fwu metadata will be available.
Adjust also env boot script the address of the
bootbank with the new gpt layout, and also remove
the not needed kernel address bank0 and bank1
and retrieve function that would test the bank flag
before and now we are getting the info from the fwu
metadata.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
We need to distinguish between boot banks and from which
partition to load the kernel+initramfs to memory.
For that, fetch the boot index, fetch the correspondent
partition, calculate the correct kernel address and
then set the env variable kernel_addr with that value.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
it is expected that the firmware that runs before
u-boot somehow provide the information of the bank
for now we will fetch the info from the metadata
since the Secure enclave is the one responsible for
this information.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
The correct specifier of the section is ".data" and not "data",
use the former to place the variables in ".data" section.
Fixes: 731fd50e27 ("ARM: stm32: Implement board coding on AV96")
Fixes: 92ca0f7446 ("ARM: dts: stm32: Synchronize DDR setttings on DH SoMs")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
This fixes the following run time error message:
set_dir_flags: error: gpio PIOD3 not reserved
set_dir_flags: error: gpio PIOC14 not reserved
Signed-off-by: Ilko Iliev <iliev@ronetix.at>
Remove the function board_mtdparts_default and the associated file
or configs, only used by the CONFIG_SYS_MTDPARTS_RUNTIME now removed.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Copy the fixed partition nodes from U-Boot device tree to Linux kernel
device tree to dynamically configure the MTD partitions.
fdt_copy_fixed_partitions is only based on device tree
and replace the function fdt_fixup_mtdparts based on mtdparts variable;
the variable mtdid and mtdparts are not more required.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Call pci_init() from board_init() to force PCI enumeration at probe time.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Since the new RevC LX2160A-RDB board has its 10G Aquantia PHYs at
different MDIO bus addresses, we must update both the kernel DTS and
u-boot's DTS (in case of DM_ETH) in case the board is indeed RevC or
newer. Use the newly introduced get_board_rev() function to trigger a
fixup of the kernel DTS to properly match the actual PHY addresses.
All this is encapsulated in the fdt_fixup_board_phy_revc() function
which will be used in the next patch.
Use the newly fdt_fixup_board_phy_revc() function introduced to
update both kernel's DTS and u-boot's DTS.
Signed-off-by: Florin Chiculita <florinlaurentiu.chiculita@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add new API for obtaining board revision and trigger the i2c node
fixup with this new API.
Signed-off-by: Florin Chiculita <florinlaurentiu.chiculita@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
While invoking "zynqmp tcminit mode" command (which is invalid command)
on U-Boot, it just works. Check the mode param, if it is valid then
only initialize the TCM.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20230608032152.980-2-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Process errors from command via cmd_process_error() as is done on Versal.
When internal function returns different number then CMD_RET_SUCCESS(0),
CMD_RET_FAILURE(1) or CMD_RET_USAGE(-1) shell react on these errors by
throwing an error like
"exit not allowed from main input shell." that's why use
cmd_process_error() to make sure that error code is all the time correct.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/d511935ba10daf95c70996fae6e6ffc374efffa0.1685618464.git.michal.simek@amd.com
Production version restarting platform version field from 0 that's why add
new calculation to be able to use different DT for these platforms.
Requested DT names for production silicons for IPP/SPP and EMU platform are
versal-net-ipp-rev2.0.dts and versal-net-emu-rev2.0.dts.
If platform version increase numbers revision can be even higher.
As of today platform version is 2 that's why expected is rev2.2.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/691e166b3cf2643d7edf482bda5500163eecb35a.1684311689.git.michal.simek@amd.com
Read boodmode register using versal_net_get_bootmode() in board_late_init
and prepare corresponding distro boot command sequence based on it.
versal_net_get_bootmode() will be changed to use smc calls later, but
for now directly reads the register.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230516144753.30869-1-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
The function fdtdec_board_setup() is called early and adds the overlay
from ATF to the u-boot device tree. That is necessary so that u-boot
doesn't use reserved memory.
Linux also needs to know about that reserved memory so the overlay from
ATF needs to be aplied on the linux device tree as well.
This commit makes sure that the ATF overlay is applied to both device trees.
Signed-off-by: Detlev Casanova <detlev.casanova@collabora.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Adam Ford <aford173@gmail.com>
Add code to support FWU_MULTI_BANK_UPDATE.
The platform does not have gpt-partition storage for
Banks and MetaData, rather it used SPI-NOR backed
mtd regions for the purpose.
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Add board code for the R8A77980 V3HSK board.
Add CPLD sysreset driver to the R-Car V3H SK board.
Extracted from a larger patch by Valentine Barshak.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Tam Nguyen <tam.nguyen.xa@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Sync configs and board code with V3H Condor, squash CPLD driver in]
Add board code for the R8A77970 V3MSK board.
Add CPLD sysreset driver to the R-Car V3M SK board.
Extracted from a larger patch by Valentine Barshak.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Tam Nguyen <tam.nguyen.xa@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Sync configs and board code with V3M Eagle, squash CPLD driver in]
Introduce weak default board_init() in rcar-common/common.c , which
allows complete removal of ebisu.c and condor.c at the same time .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The eagle.h is now empty and only includes rcar-gen3-common.h .
Use rcar-gen3-common.h directly instead and drop eagle.h .
No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Pull common board initialization code from V3M Eagle board
into rcar-common/v3-common.c so it can be re-used by other
V3M/V3H boards.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
There is no need to pull in all those headers as the board file is
basically empty. Drop them all.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
There is no need to pull in all those headers as the board file is
basically empty. Drop them all.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The reset_cpu() implementation is basically the same across Gen3
SoCs and identical across Gen4 SoCs. Introduce weak default for
reset_cpu(), so that it does not have to be duplicated in every
board file again.
There is a slight difference for CA53 only systems, like E3 and D3,
which now check MIDR for CPU ID first just like the other systems,
but this is OK since the MIDR always returns CA53 core type and the
correct reset register is written.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The number of image array entries global variable is required
to support EFI capsule update. This information is exposed as a
num_image_type_guids variable, but this information
should be included in the efi_capsule_update_info structure.
This commit adds the num_images member in the
efi_capsule_update_info structure. All board files supporting
EFI capsule update are updated.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
It seems like the header inclusion guard for some Freescale crosspoint
switch header was misspelled.
Make the preprocessor symbol for the #ifndef and #define lines the
same, so that the double inclusion protection works as expected.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This platform is currently unmaintained and untested, so remove it.
Further, as it is the only TI816X SoC example, remove related files as
well.
Signed-off-by: Tom Rini <trini@konsulko.com>
Update DDR timing file generated by DDR Config Tool
1. Dynamic refresh rate is set by default
2. The 3rd freq will be 625MTS based on power and performance better than 100MTS.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add a static u-boot config for i.MX93 low drive mode support. When
low drive mode is enabled, VDD_SOC is set to 0.75V. Bus clocks,
A55 core clock (900Mhz), DDR clock (1866MTS), and some peripherals
clocks (USDHC/FLEXSPI/PDM/DISP_PIX/CAM_PIX) must decrease to meet
max frequencies in low drive mode.
Also set standby voltage for buck1
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Move imx8 sci header file to include/firmware/imx, then we could
use build macro to reuse some i.MX8 drivers for i.MX9, such as
drivers/cpu/imx8_cpu.c.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Stefano Babic <sbabic@denx.de>
When using a list of writeable variables, the initial values come from
the built-in default environment since commit 5ab8105836
("env: Complete generic support for writable list"). Remove unnecessary
misuse of the env is nowhere driver as default environment.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
When using a list of writeable variables, the initial values come from
the built-in default environment since commit 5ab8105836
("env: Complete generic support for writable list"). Remove unnecessary
misuse of the env is nowhere driver as default environment.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
When using a list of writeable variables, the initial values come from
the built-in default environment since commit 5ab8105836
("env: Complete generic support for writable list"). Remove unnecessary
misuse of the env is nowhere driver as default environment.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Otherwise non-ChromeOS samsung devices, like the odroid boards, are
stuck in a bootloop if CONFIG_CROS_EC is not enabled:
<...>
MMC: SAMSUNG SDHCI: 2, EXYNOS DWMMC: 0
Loading Environment from MMC... *** Warning - bad CRC, using default environment
cros-ec communications failure -96
Please reset with Power+Refresh
Cannot init cros-ec device
resetting ...
Issue started after commit e44d7e73fe ("dm: core: Switch
uclass_*_device_err to use uclass_*_device_check").
Signed-off-by: Henrik Grimler <henrik@grimler.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
Renesas RZ/N1 devices contain BootROM code that loads a custom SPKG
image from QSPI, NAND or USB DFU. Support this format in mkimage tool.
SPKGs can optionally be signed, however creation of signed SPKG is not
currently supported.
Example of how to use it:
tools/mkimage -n board/schneider/rzn1-snarc/spkgimage.cfg \
-T spkgimage -a 0x20040000 -e 0x20040000 \
-d u-boot.bin u-boot.bin.spkg
The config file (spkgimage.cfg in this example) contains additional
parameters such as NAND ECC settings.
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Add support for Schneider Electric RZ/N1D and RZ/N1S boards, which
are based on the Reneasas RZ/N1 SoC devices.
The intention is to support both boards using a single defconfig, and to
handle the differences at runtime.
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Prepare for linking setup_sata only when CONFIG_SATA/CONFIG_SPL_SATA
is defined.
Signed-off-by: Troy Kisky <troykiskyboundary@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
pfuze_mode_init calls pmic_reg_read which is only available from
obj-$(CONFIG_$(SPL_TPL_)DM_PMIC) += pmic-uclass.o
Prepare for conversion of defined(CONFIG_DM_PMIC) to
CONFIG_IS_ENABLED(DM_PMIC).
Signed-off-by: Troy Kisky <troykiskyboundary@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The function ft_board_setup calls do_fixup_by_path_string
which is only available on CONFIG_IS_ENABLED(OF_LIBFDT).
This prepares for the conversion.
ft_board_setup is only called from image-fdt which is linked by
obj-$(CONFIG_$(SPL_TPL_)OF_LIBFDT) += image-fdt.o
Signed-off-by: Troy Kisky <troykiskyboundary@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- Rockchip NFC driver update and dev addr pointer api update;
- use standard dr_mode for usb driver;
- rock pi boards dts update;
- Add rk3566 Anbernic boards;
- Misc fixes for drivers;
The AM64x SR2.0 SK board uses "AM64B-SKEVM" as the EEPROM identifier.
This board is similar to the AM64x SKEVM except that it has a new
PMIC that will be enabled in the future and consequently could use a
different device tree file in the future.
For now we treat the board same as an AM64x SK.
Signed-off-by: Judith Mendez <jm@ti.com>
Acked-by: Andrew Davis <afd@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
To enable splash screen on AM62x at a53 SPL setup DRAM, set page table,
enable cache to allow copying of bmp image to frame buffer and display
it using splash_display.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Change splashimage which is bmp image loadaddr to 0x80200000 since stack
is situated at 0x80477660 as splash framework requires bmp image to be
present above stack.
Change splashsource to sf to support loading bmp image from ospi flash
memory.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
The Anbernic RGxx3 is a "pseudo-device" that encompasses the following
devices:
- Anbernic RG353M
- Anbernic RG353P
- Anbernic RG353V
- Anbernic RG353VS
- Anbernic RG503
The rk3566-anbernic-rgxx3.dtsi is synced with upstream Linux, but
rk3566-anbernic-rgxx3.dts is a U-Boot specific devicetree that
is used for all RGxx3 devices.
Via the board.c file, the bootloader automatically sets the correct
fdtfile, board, and board_name environment variables so that the
correct devicetree can be passed to Linux. It is also possible to
simply hard-code a single devicetree in the boot.scr file and use
that to load Linux as well.
The common specifications for each device are:
- Rockchip RK3566 SoC
- 2 external SDMMC slots
- 1 USB-C host port, 1 USB-C peripheral port
- 1 mini-HDMI output
- MIPI-DSI based display panel
- ADC controlled joysticks with a GPIO mux
- GPIO buttons
- A PWM controlled vibrator
- An ADC controlled button
All of the common features are defined in the devicetree synced from
upstream Linux.
TODO: DSI panel auto-detection for the RG353 devices (requires porting
of DSI controller driver and DSI-DPHY driver to send DSI commands to
the panel).
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
When CMPC885 board is used for MIAE device, SCC2 SCC3 and SMC2
are used for serial lines. Therefore only SCC4 is available for
handling the TDM line.
In order to use SCC4 in QMC mode without loosing SMC2, SMC2
must be relocated.
Activate SMC relocation and relocate SMC2 at offset 0x1fc0 which
is unused.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
In order to know the motherboard type earlier, perform I/O ports
initialisation and FPGA loading in board_early_init_f() instead
of board_early_init_r().
This is needed to be able to load mpc8xx CPM microcode base on
motherboard type and before starting to use the CPM.
Console is not available yet so remove the printfs.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
This platform is unsupported by TI and was never widely distributed. As
this is untested for a long while and missing some DM conversions,
remove it and related device tree files.
Signed-off-by: Tom Rini <trini@konsulko.com>
Add support to detect daughtercards (GESI Ethernet card) in-order
to set the MAC address of the main CPSW2G interface.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Currently a few 'board/qualcomm/../Makefile' point to incorrect
path of sdm845 board file.
Fix the same.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
This adds a simple Northstar "BRCMNS" board to be used with
the BCM4708x and BCM5301x chips.
The main intention is to use this with the D-Link DIR-890L
and DIR-885L routers for loading the kernel into RAM from
NAND memory using the BCH-1 ECC and using the separately
submitted SEAMA load command, so we are currently not adding
support for things such as networking.
The DTS file is a multiplatform NorthStar board, designed to
be usable with several NorthStar designs by avoiding any
particulars not related to the operation of U-Boot.
If other board need other ECC for example, they need to
create a separate DTS file and augment the code, but I don't
know if any other users will turn up.
Cc: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently, it is recommended to move from CFG_EXTRA_ENV_SETTINGS to
an env file, so do the conversion.
Suggested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Currently, only the first MAC address is read from the fuses.
The second MAC address is not read and Linux assigns a random one.
To prevent this behavior, read the second MAC address from the fuses
and store it into the eth1addr environment variable so that it
can be passed to Linux.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Add lockdown U-Boot env support so that only certain U-Boot environment
variables are allowed to be modified.
Signed-off-by: Eduard Strehlau <eduard@lionizers.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
GPT Partition labels are used for determining the right
root filesystem to boot from.
The U-Boot environment is configured to reside in the eMMC hardware
boot partition we are currently booted from.
This should enable a dual copy approach for upgrading the bootloader.
One can overwrite the inactive hardware partition with new bootloader
and environment and afterwards switch the eMMC boot partition for an
atomic bootloader switch.
Signed-off-by: Eduard Strehlau <eduard@lionizers.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
The MNT Reform 2 is a modular DIY laptop. In its initial version it
is based on the BoundaryDevices i.MX8MQ SoM. Some parts have been
lifted from BoundaryDevices official U-Boot downstream project.
Signed-off-by: Patrick Wildt <patrick@blueri.se>
Tested-by: Vagrant Cascadian <vagrant@debian.org>
Tested-by: Vagrant Cascadian <vagrant@debian.org>
Signed-off-by: Stefano Babic <sbabic@denx.de>
Please pull the second part of the sunxi pull request for this cycle.
Another bunch of patches that replace old-school U-Boot hacks with
proper DM based code, this time for the raw NAND flash driver, and the
USB PHY VBUS detection code. Plus two smaller patches that were sitting
in my inbox for a while.
Gitlab CI passed. In lack of some supported board with NAND flash I
couldn't really test this part, but apparently this was tested by the
reviewer. I briefly ran the branch on some boards with USB-OTG, and
this still worked.
This pull request adds support for the last CPU board from
CS GROUP France (previously CSSI).
That CPU board called CMPCPRO has a mpc8321E CPU (Family PQII PRO hence
its name) and can be plugged in place of the CMPC885 board.
In order to support that new board, the following changes are included
in this series:
- Make the mpc8xx watchdog driver more generic for reusing it
with mpc83xx
- Fix various small problems on mpc83xx platform
- Add a GPIO Driver for QE GPIOs
- Add support for mpc832x into mpc83xx SPI driver
- Refactor existing board code that will be shared with new board
- Add the new board
CSSI has another CPU board, similar to the CMPC885 board
that get plugged on the two base boards MCR3000_2G and MIAE.
That CPU board is called CMPCPRO because it has a MPC8321E CPU,
also known as Power QUICC II PRO.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
All the code used to manage the mother boards will be
common to soon to come CPU board.
Move all that code into common.c
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
On cmpc885 board, the ethernet addresses are stored in an
EEPROM that is accessed through SPI.
A 3 bytes command is sent to the chip then the content
gets read. At the time being a single block access is
performed, ignoring the first 3 bytes read.
Reword the SPI transfer to first send 3 bytes then
receive the content of the EEPROM so that there don't be
3 dummy bytes at the beginning of the buffer.
And move the function into common.c so that it can be
reused by the board that will be added in a future patch.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
In preparation of the new cssi board called cmpcpro which
we be introduce in a future patch, move common
functions into a dedicated file in a common directory.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Clocks, resets, and pinmuxes are now handled by the driver model, so the
only thing the "board" code needs to do is load the driver. This matches
the pattern used by other DM raw NAND drivers (there is no NAND uclass).
The actual board code is now only needed in SPL.
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
When building with clang, we see:
board/emulation/common/qemu_dfu.c:51:24: warning: 'memset' call operates on objects of type 'char' while the size is based on a different type 'char *' [-Wsizeof-pointer-memaccess]
As we're calling memset with the length set to the size of the pointer
and not the size of the buffer. Correct this with a call of the size of
the buffer itself.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Sughosh Ganu <sughosh.ganu@linaro.org>
The Arm EBBR (Embedded Base Boot Requirements) require that the time
and basic networking EFI interfaces are available and working, so long
as the hardware has an RTC and network interface.
Arm FVPs typically have a memory-mapped PL031 RTC and a VIRTIO_NET
device defined in the device tree, so "imply" these in the Kconfig for
the FVP base model to simplify creating EBBR-compliant firmware.
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
BASE_FVP now typically uses a devicetree provided by a prior boot stage
(typically Arm TF-A), so imply this option by default when
TARGET_VEXPRESS64_BASE_FVP is selected.
OF_HAS_PRIOR_STAGE selects OF_BOARD so this change is minor, but aligns
TARGET_VEXPRESS64_BASE_FVP with TARGET_VEXPRESS64_BASER_FVP.
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Move to using .env file for setting up environment variables for am64x.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
Add ospi boot media support to load splash image from OSPI memory,
add offset to read image from ospi and necessary flags defininig type
of storage and storage device.
Use CONFIG_IS_ENBALED to use the splash locations at SPL and u-boot
proper.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
This matches AM64 and J721e and removes the need to forward
declare k3_spl_init(), k3_mem_init(), and check_rom_loaded_sysfw()
in sys_proto.h.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
This matches how it was done for pre-K3 TI platforms and it allows
us to move the forward declaration out of sys_proto.h.
It also removes the need for K3_BOARD_DETECT as one is free to simply
override the weak function in their board files as needed.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
The TARGET_x_R5_EVM check is already enough to limit these defines to
only the correct builds. Remove the extra outer check.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
The MSMC fixup is something we do based on SoC, not based on the board.
So this fixup does not belong in the board files. Move this to the
mach-k3 common file so that it does not have to be done in each board
that uses these SoCs.
We use ft_system_setup() here instead of ft_board_setup() since it is no
longer board level. Enable OF_SYSTEM_SETUP in the configurations that use
this to keep functionality the same.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
- Add rk3588 evb support;
- Update pinctrl for rk3568 and rk3588;
- Update rk3288 dts;
- Update mmc support for rk3568 and rk3588;
- Add rng support for rk3588;
- Add DSI support for rk3568;
- Some other misc fixes in dts, config, driver;
_ Add usb_pgood_delay for ST boards
_ increase malloc size for pre-reloc for stm32mp15
_ Set CONFIG_USB_HUB_DEBOUNCE_TIMEOUT=2s for stm32mp15
dts:
_ Add QSPI support on STM32MP13x SoC family
_ Add FMC support on STM32MP13x SoC family
drivers/machine:
_ pinctrl_stm32: Add slew rate support for stm32_pinctrl_get_pin_muxing()
_ spi: stm32_qspi: Remove useless struct stm32_qspi_flash
_ rawnand: stm32_fmc2: remove unsupported EDO mode
_ stm32mp: fix various array bounds checks
-----BEGIN PGP SIGNATURE-----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=3Txq
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20230419' of https://source.denx.de/u-boot/custodians/u-boot-stm
configs:
_ Add usb_pgood_delay for ST boards
_ increase malloc size for pre-reloc for stm32mp15
_ Set CONFIG_USB_HUB_DEBOUNCE_TIMEOUT=2s for stm32mp15
dts:
_ Add QSPI support on STM32MP13x SoC family
_ Add FMC support on STM32MP13x SoC family
drivers/machine:
_ pinctrl_stm32: Add slew rate support for stm32_pinctrl_get_pin_muxing()
_ spi: stm32_qspi: Remove useless struct stm32_qspi_flash
_ rawnand: stm32_fmc2: remove unsupported EDO mode
_ stm32mp: fix various array bounds checks
rk3588 evb1 v10 is a evalution board from Rockchip, it is a dev board for
rockchip and also a reference board for board vendors.
Hardware:
SoC: RK3588
DRAM: LPDDR4X 8GB
Debug: UART2 via USB
PCIe: 3x4 *1
SATA *2
HDMI out *2
HDMI IN *1
USB2.0 Host *2
USB3.0 Host *1
Type C *1
MIPI DSI panel
dts Sync from Linux v6.2.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Jagan Teki <jagan@edgeble.ai>
Instead of letting the compiler error out if CONFIG_ENV_IS_NOWHERE is
not selected by the user, let's just enforce it when the user builds for
Ringneck PX30 so that no check needs to be performed by the compiler and
the configuration is always valid.
Suggested-by: Tom Rini <trini@konsulko.com>
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Instead of letting the compiler error out if CONFIG_ENV_IS_NOWHERE is
not selected by the user, let's just enforce it when the user builds for
Puma RK3399 so that no check needs to be performed by the compiler and
the configuration is always valid.
Suggested-by: Tom Rini <trini@konsulko.com>
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add Kconfig to select the basic functions for StarFive VisionFive v2 Board.
Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
Tested-by: Conor Dooley <conor.dooley@microchip.com>
Add board support for StarFive VisionFive v2.
Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
Tested-by: Conor Dooley <conor.dooley@microchip.com>
In all these cases, the index on the LHS is immediately afterwards
used to access the array appearing in the ARRAY_SIZE() on the RHS - so
if that index is equal to the array size, we'll access
one-past-the-end of the array.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
- Spring Cleanup of Amlogic board documentation
- add support for BananaPi M2-Pro
- add support for BananaPi M2S
- add support for Radxa Zero2
- add support for WeTek Hub and WeTek Play2
- switch LibreTech-CC v2 and WeTek Core2 to EE powerdomain
- add support for Beelink GT1 Ultimate
-----BEGIN PGP SIGNATURE-----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=Vf7Q
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20230417' of https://source.denx.de/u-boot/custodians/u-boot-amlogic
- Add initial support for BPI-CM4
- Spring Cleanup of Amlogic board documentation
- add support for BananaPi M2-Pro
- add support for BananaPi M2S
- add support for Radxa Zero2
- add support for WeTek Hub and WeTek Play2
- switch LibreTech-CC v2 and WeTek Core2 to EE powerdomain
- add support for Beelink GT1 Ultimate
The first two patches are by Frieder Schrempf who joins as a reviewer for
the SPI NAND framework and drivers.
The following 2 patches are by Linus Walleij and are taken by the series
"Add Broadcom Northstar basic support".
Bin Meng makes static a list for octeontx.
Francesco Dolcini specifies MTD partitions on command line for
colibri-{imx6ull,imx7}.
-----BEGIN PGP SIGNATURE-----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=1lGu
-----END PGP SIGNATURE-----
Merge tag 'u-boot-nand-20230417' of https://source.denx.de/u-boot/custodians/u-boot-nand-flash
Pull request for u-boot-nand-20230417
The first two patches are by Frieder Schrempf who joins as a reviewer for
the SPI NAND framework and drivers.
The following 2 patches are by Linus Walleij and are taken by the series
"Add Broadcom Northstar basic support".
Bin Meng makes static a list for octeontx.
Francesco Dolcini specifies MTD partitions on command line for
colibri-{imx6ull,imx7}.
Add build instructions for the WeTek Hub and WeTek Play2 boards.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230323143142.780306-15-christianshewitt@gmail.com
[narmstrong: fixed doc build]
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Add configurations for the WeTek Hub and WeTek Play2 boards.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230323143142.780306-14-christianshewitt@gmail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
The bananapi-m5 docs are missing from the file, so add them.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230323143142.780306-2-christianshewitt@gmail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
GS-King-X is also supported with the beelink-s922x FIP sources and can use
the GT-King defconfig. Add a board document with instructions.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Link: https://lore.kernel.org/r/20230320114609.930145-33-christianshewitt@gmail.com
[narmstrong: fixed doc build]
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Add support for both the BananaPi BPI-CM4 module and the BananaPi
baseboard which is compatible with the RaspberryPi CM4IO baseboard.
The BananaPi BPI-CM4 module follows the CM4 specifications at [1],
but with a single HDMI port and a single DSI output.
The current CM4IO baseboard DT should work fine on the Raspberry CM4
baseboard and other derivatives baseboards, but proper DT should
be written for other baseboards.
[1] https://datasheets.raspberrypi.com/cm4io/cm4io-datasheet.pdf
Link: https://lore.kernel.org/r/20230307-u-boot-cm4-v1-2-43f5a393cd37@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
There is an existing CONFIG_MCFTMR Kconfig symbol,
use it and drop all other instances of CFG_MCFTMR.
This duality is likely a result of bogus conversion
to Kconfig.
Fixes: 7ff7b46e6c ("m68k: rename CONFIG_MCFTMR to CFG_MCFTMR")
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Mask macro PART_ACCESS_MASK filter out access bits of emmc register and
macro EXT_CSD_EXTRACT_BOOT_PART() extracts boot part bits of emmc register.
So use EXT_CSD_EXTRACT_BOOT_PART() when extracting boot partition.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add board code for R8A779G0 V4H White Hawk board.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Synchronize configuration symbols which are now switched to Kconfig
Mallocate gd->bd->bi_boot_params, i.e. drop the assignment
Sort headers, use clrbits_le32(), use BIT macros where appropriate
Use CONFIG_SYS_CLK_FREQ for counter frequency instead of custom macro]
Add board code for R8A779F0 S4 Spider board.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Synchronize configuration symbols which are now switched to Kconfig
Mallocate gd->bd->bi_boot_params, i.e. drop the assignment
Sort headers, use clrbits_le32(), use BIT macros where appropriate
Use CONFIG_SYS_CLK_FREQ for counter frequency instead of custom macro]
This adds R-Car Generation 4 (Gen4) support as Renesas ARM64 SoC.
In this version, reusing R-Car Gen3 lowlevel initialize routine [1]
and R-Car Gen3 memory map tables [2] .
[1] arch/arm/mach-rmobile/lowlevel_init_gen3.S
[2] arch/arm/mach-rmobile/memmap-gen3.c
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: - Enable DTO support by default
- Sort the Kconfig lists
- Select RCAR_64 Kconfig option to pull in all the shared
Kconfig options with Gen3, and use where applicable to
deduplicate entries.
- Fix reference [2] typo in commit message
- Drop config options moved to Kconfig, rename rest to CFG_
accordingly to synchronize with upstream changes. Drop
removed CONFIG_VERY_BIG_RAM.
- Move board size limit to arch/Kconfig
- Move GICR_BASE to headers instead of common config]
mpc8xx, mpc83xx and mpc86xx have similar watchdog with almost same
memory registers.
Refactor the driver to get the register addresses from the
device tree and use the compatible to know the prescale factor.
Calculate the watchdog setup value from the provided timeout.
Don't declare it anymore as an HW_WATCHDOG, u-boot will start
servicing the watchdog early enough.
On mpc8xx the watchdog configuration register is also used for
configuring the bus monitor. So add it as an option to the watchdog
when it is mpc8xx. When watchdog is not selected, leave the
configuration of the initial SYPCR from Kconfig.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
There is no need for the board file to instantiate a PL01X platform
device anymore. This is all taken care of by the DM code which now will
probe the device based on the DT node.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Beacon Embedded has an i.MX8M Plus development kit which consists
of a SOM + baseboard. The SOM includes Bluetooth, WiFi, QSPI, eMMC,
and one Ethernet PHY. The baseboard includes audio, HDMI, USB-C Dual
Role port, USB Hub with five ports, a PCIe slot, and a second Ethernet
PHY. The device trees are already queued for inclusion in Linux 6.3.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add support for Data Modul i.MX8M Plus eDM SBC board. This is an
evaluation board for various custom display units. Currently
supported are serial console, ethernet, eMMC, SD, SPI NOR, USB.
Signed-off-by: Marek Vasut <marex@denx.de>
change prints to show which DDR configuration (single/dual rank) is used
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Deduplicate similar DDRC configurations and LPDDR4 training patterns
by patching a single configuration.
The aim is to reduce the SPL memory footprint and simplify maintenance
of lpddr4_timing.c
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Update LPDDR4 configuration and training using updated spreadsheet and
tools from NXP using data from previous spreadsheet and verified
toward datasheet:
- MX8M_Plus_LPDDR4_RPA_v9.xlsx
- mscale_ddr_tool_v3.30.exe
From:
https://community.nxp.com/t5/i-MX-Processors-Knowledge-Base/i-MX-8M-Family-DDR-Tool-Release/ta-p/1104467
Some register values differ due to these fixes/modifications:
- corrected calculation of T_CKPDX parameter (equal to tCKCKEH for LPDDR4)
- corrected ECC related items, none of which affect normal operation
when ECC is not enabled
- corrected formula for calculation of tRTP in cell D122
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Change tRFCmin (tRFCab) from 280 ns to 380 ns to be compliant with
current and futures memories.
Fixes: 2bc2f817ce ("board: toradex: add verdin imx8m plus support")
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Add support to Verdin IMX8MP V1.1B SKU which uses
MT53E1G32D2FW-046 WT:B memory.
Compared to the 8 GB memory (MT53E2G32D4NQ-046 WT:A) used on
Verdin IMX8MP V1.0A it has 16 row addresses instead of 17.
In fact, the new memory, is a 2 GB/rank memory. The 8 GB memory is a
4 GB/rank memory.
Manually tweaking Host Interface addresses vs LPDDR4 signals mapping it
is possible to have a single configuration working with both memories:
- Old configuration: HIF bit 30 -> rank, HIF bit 29 -> Row 16
- New configuration: HIF bit 29 -> rank, HIF bit 30 -> Row 16
With this change the memory space from the host processor is contiguous
for both the configurations and the correct memory size is computed
using get_ram_size() at runtime.
Support for single rank memories still works thanks to the fact
dual ranks training fails (ddr_init->ddr_cfg_phy) toward single rank
memories.
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
---------------------------------
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/15819
i.MX patches queued for next:
- Conversions to DM_SERIAL
- Fixes for Toradex boards
- Gateworks Boards
- i.MX8ULP
- EQoS support / fixes, changes in boards
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQS2TmnA27QKhpKSZe309WXkmmjvpgUCZCaU0Q8cc2JhYmljQGRl
bnguZGUACgkQ9PVl5Jpo76YCKgCgk4OueoIggmes+Ccj8bu1BcQbrfYAoJAgMeKE
It0hrVAifD62TPb2rmHt
=hFVG
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-next-20230331' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx into next
u-boot-imx-next-20230331 for next
---------------------------------
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/15819
i.MX patches queued for next:
- Conversions to DM_SERIAL
- Fixes for Toradex boards
- Gateworks Boards
- i.MX8ULP
- EQoS support / fixes, changes in boards
The FEC interface mode is now configured in common board_interface_eth_init()
and called by FEC MAC driver when appropriate. Drop the board side duplicates
if the same functionality.
Signed-off-by: Marek Vasut <marex@denx.de>
The EQoS interface mode is now configured in common board_interface_eth_init()
and called by EQoS MAC driver when appropriate. Drop the board side duplicates
if the same functionality.
Signed-off-by: Marek Vasut <marex@denx.de>
We have a few places here that the function declarations do not
match their prototypes, correct them.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paulliu@debian.org>
Cc: Tom Rini <trini@konsulko.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reported-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The following expression is used to construct the device tree name:
fdtfile=${soc}-colibri-${fdt_board}.dtb
- soc is set dynamically (either imx8qxp or imx8dx)
- fdt_board can be modified by the user (eval-v3, aster, iris/iris-v2)
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Refactor the detection of QXP vs. DX SoC into its own helper function.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
All Colibri iMX8X variants have 2nd RGMII on SoC, so add the address
for 2nd ethernet.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
