2
0
Fork 0
mirror of https://github.com/AsahiLinux/u-boot synced 2024-12-26 13:03:40 +00:00
Commit graph

16274 commits

Author SHA1 Message Date
Mathew McBride
29760c8e6d board: ten64: add missing error checks for retimer power on
The retimer reset/power on logic was changed in a recent commit,
however, it neglected to check if the commands sent to the
board microcontroller (to control power to the retimer chip)
actually completed.

Add return checks for these operations so any failures will
be reported to the user.

Signed-off-by: Mathew McBride <matt@traverse.com.au>
Fixes: 7a041fea2 ("board: traverse: ten64: ensure retimer reset
is done on new board revisions")
2023-08-07 13:41:44 -04:00
Marek Vasut
3cc7708dfd ARM: renesas: Update MAINTAINERS file
Update MAINTAINERS file. Add missing MAINTAINERS file for Spider,
Whitehawk and V3HSK boards. Update mail addresses. Add file globs
to match on DT and driver files related to these boards.

The GRPEACH and R2DPLUS are special in that they are not R-Car
and have their own set of specialized drivers.

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
2023-08-07 13:41:43 -04:00
Mihai Sain
87d1cac49d board: at91: sama5d29_curiosity: add initial support for sama5d29_curiosity
Add initial support for sama5d29_curiosity board.

Hardware:
SoC: SAMA5D29 500 MHz
DRAM: LPDDR2 512 MiB
PMIC: MCP16502
Debug: UART0
Flash: QSPI NOR 8 MiB
RGB LCD connector
Mikrobus connectors x 2
SD-Card connectors x 2
USB 2.0 x 2

Signed-off-by: Mihai Sain <mihai.sain@microchip.com>
2023-08-07 11:42:16 +03:00
Marcel Ziswiler
7d1a10659f board: toradex: add verdin am62 support
This adds initial support for the Toradex Verdin AM62 Quad 1GB WB IT
V1.0A module and subsequent V1.1 launch configuration SKUs. They are
strapped to boot from their on-module eMMC. U-Boot supports booting
from the on-module eMMC only, DFU support is disabled for now due to
missing AM62x USB support.

The device trees were taken straight from Linux v6.5-rc1.

Boot sequence is:
SYSFW ---> R5 SPL (both in tiboot3.bin) ---> ATF (TF-A) ---> OP-TEE
  ---> A53 SPL (part of tispl.bin) ---> U-boot proper (u-boot.img)

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
2023-08-04 15:03:42 -04:00
Marcel Ziswiler
0bcfda1b51 toradex: tdx-cfg-block: add verdin am62 skus
Add initial Verdin AM62 Quad 1GB WB IT prototype and launch
configuration SKUs to ConfigBlock handling.

0069: Verdin AM62 Quad 1GB WB IT
0071: Verdin AM62 Solo 512MB
0072: Verdin AM62 Solo 512MB WB IT
0073: Verdin AM62 Dual 1GB ET
0074: Verdin AM62 Dual 1GB IT
0075: Verdin AM62 Dual 1GB WB IT
0076: Verdin AM62 Quad 2GB WB IT

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
2023-08-04 13:32:39 -04:00
Max Krummenacher
a0383427b3 toradex: tdx-cfg-block: rework display adapter name handling
Rework the rather big array of zero length strings with 4 entries of
actual display adapter names to a array of structs which ties a pid4
to its correspondent human readable string.
Provide an accessor to get the string for a given PID4.

Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
2023-08-04 13:32:39 -04:00
Max Krummenacher
39e521f756 toradex: tdx-cfg-block: rework carrier board name handling
Rework the rather big array of zero length strings with 4 entries of
actual carrier board names to a array of structs which ties a pid4
to its correspondent human readable string.
Provide an accessor to get the string for a given PID4.
Rework the user of the information to use the accessor.

Note that check_pid8_sanity() is used for early samples of Dahlia and
the development board. Yavia isn't affected.

Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
2023-08-04 13:32:39 -04:00
Max Krummenacher
94757b47f1 toradex: tdx-cfg-block: add yavia carrier cfg block info
Add the Yavia Carrier board name string to the known carrier
board list.

Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
2023-08-04 13:32:26 -04:00
Tom Rini
e205fbcea0 rzn1-snarc: Add missing MAINTAINERS file
This should have been included when the platform was added, make one
now.

Signed-off-by: Tom Rini <trini@konsulko.com>
2023-08-03 15:30:53 -04:00
Tom Rini
eda90d2467 board/freescale: Drop two orphaned entries
As the defconfig files here have been removed we can also remove the
entries.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2023-08-03 15:30:53 -04:00
Tom Rini
b54fad3fe2 vexpress64: Rework MAINTAINERS file slightly
Given that we no longer have a configs/vexpress_aemv8a_defconfig file,
drop that and then include at least the aarch64-specific config.h file
here.  Also move Linus and Peter up to the main entry as well so that
they'll get tagged for the board code too and not literally only the
defconfig.

Signed-off-by: Tom Rini <trini@konsulko.com>
2023-08-03 15:30:53 -04:00
Marek Vasut
c2ad5318d2 ARM: imx: Update MAINTAINERS file on DH electronics i.MX8M Plus DHCOM
Make use of globs to cover all the DTs and defconfigs.
Fill in missing DH u-boot list name.

Signed-off-by: Marek Vasut <marex@denx.de>
2023-08-03 15:30:53 -04:00
Sean Anderson
aa423f2bc6 freescale: Remove Rajesh Bhagat MAINTAINERS
Rajesh's email bounces. Remove his email from all boards he maintains.
Fortunately, he has co-maintainers on most boards. I have taken the
liberty of volunteering Pramod to maintain the LS1012AFRDM, since he
also maintains the LS1012AFRWY. Let me know if the board should be
orphaned instead.

Signed-off-by: Sean Anderson <sean.anderson@seco.com>
2023-08-03 15:30:53 -04:00
Mathew McBride
1c35cc85ad board: ten64: strip extra u-boot compatibles from FDT
The u-boot version of the LS1088A device tree has
an extra compatible (simple-mfd) added to &fsl_mc
to facilitate usage with U-Boot's device model.

Unfortunately FreeBSD will only match the single
"fsl,qoriq-mc" exactly when the node is a "bus"
object, so we need to strip out the extra compatible
before presenting it to the operating system.

Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
2023-08-03 09:40:50 -04:00
Mathew McBride
67de5966e6 board: ten64: opt out of fsl_setenv_bootcmd
Our bootcmd is the same regardless of where the SoC
loaded it's code from, so we don't want
fsl_setenv_bootcmd to do anything.

Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
2023-08-03 09:40:50 -04:00
Mathew McBride
06e19a6d3e board: traverse: ten64: set serial# to be 'label' MAC
The GE0 (first Gigabit Ethernet interface) is used as the
'serial number' for the board and appliance.

To ensure the 'true' board S/N is available regardless of how
the DPAA2 subsystem is configured, use serial# so it is passed in
the device tree.

Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
2023-08-03 09:40:50 -04:00
Mathew McBride
56610ef5f3 board: traverse: ten64: fix allocation order of MAC addresses
On Ten64 boards, the "serial number" is the MAC address of the
first Gigabit Ethernet interface (labelled GE0 on the appliance),
and counted up from there.

The previous logic did not take into account U-Boot's ordering
of the network interfaces. By setting aliases/ethernetX in the device
tree we can ensure the U-Boot 'ethX' is the same as the labelled
port order on the unit, as well as the one adopted by Linux.

Signed-off-by: Mathew McBride <matt@traverse.com.au>
2023-08-03 09:40:50 -04:00
Mathew McBride
080ea65692 board: traverse: ten64: init nvme devices in late boot to ensure bootflow availability
Ensure nvme devices are scanned before reaching the shell,
otherwise extra user intervention ("nvme scan") is required
before they are visible to bootdev/bootflow.

Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
2023-08-03 09:40:50 -04:00
Mathew McBride
7a041fea2d board: traverse: ten64: ensure retimer reset is done on new board revisions
Board revision C (production) and later require the SFP+
retimer to be turned on (or reset) on boot, by way of issuing
a command to the board's microcontroller (via I2C).

The comparison statement here was incorrect, as the board
ID decrements every revision (from 0xFF downwards),
so this was matching board RevA,B,C instead of Rev >= C.

Another oops that transpired when working on this issue,
is that if the board controller is not called (such as
CONFIG_TEN64_CONTROLLER=n or earlier board rev), then
the retimer udevice was not obtained. So the board
version check has to be moved inside board_cycle_retimer
(which probes/fetches the retimer device) as well.

Signed-off-by: Mathew McBride <matt@traverse.com.au>
2023-08-03 09:40:50 -04:00
Mathew McBride
269b4a3550 board: traverse: ten64: recognize board revision D
Ten64 board revision D is a variant that removes the USB hub
and PCIe expander/switch, but is otherwise compatible with the
main production "C" version.

At the same time, revise the printf specifiers (PCB version
"1064-0201%s") to reduce the number of string characters related
to the boot printout.

Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
2023-08-03 09:40:50 -04:00
Weijie Gao
bc4adc97cf board: mediatek: add MT7988 reference boards
This patch adds general board files based on MT7988 SoCs.

MT7988 uses one mmc controller for booting from both SD and eMMC,
and the pins of mmc controller booting from SD are also shared with
one of spi controllers.
So two configs are need for these boot types:

1. mt7988_rfb_defconfig - SPI-NOR, SPI-NAND and eMMC
2. mt7988_sd_rfb_defconfig - SPI-NAND and SD

Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
2023-08-03 09:40:50 -04:00
Weijie Gao
5fd6d4c7b3 arm: mediatek: retrieve ram_base from dts node for armv8 platform
Now we use fdtdec_setup_mem_size_base() to get DRAM base from fdt ram node
and update gd->ram_base. CFG_SYS_SDRAM_BASE is unused and will be removed.

Also, since mt7622 always passes fdt to linux kernel, there's no need to
assign value to gd->bd->bi_boot_params.

Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
2023-08-03 09:40:48 -04:00
Bin Meng
02be57caf7 riscv: qemu: Enable usb keyboard as an input device
This brings PCI xHCI support to QEMU RISC-V and uses a usb keyboard
as one of the input devices.

Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2023-08-02 16:32:44 +08:00
Bin Meng
124308e67b riscv: qemu: Remove out-of-date "riscv, kernel-start" handling
Commit 66ffe57 ("riscv: qemu: detect and boot the kernel passed by QEMU")
added some logic to handle "riscv,kernel-start" in DT and stored the
address to an environment variable kernel_start.

However this "riscv,kernel-start" has never been an upstream DT binding.
The upstream QEMU never generates such a DT either. Presumably U-Boot
development was based on a downstream QEMU fork.

Now we drop all codes in commit 66ffe57, except that BOARD_LATE_INIT
is kept for later use.

Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2023-08-02 16:32:41 +08:00
Bin Meng
608b80b5b8 riscv: qemu: Enable PRE_CONSOLE_BUFFER
By default the video console only outputs messages after it's ready.
Messages before that won't show on the video console, but U-Boot has
an option to buffer the console messages before it's ready.

Enable this support, and carefully select an address for the buffer.

Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2023-08-02 16:32:36 +08:00
Bin Meng
716161663e riscv: qemu: Enable Bochs video support
Enable video console using the emulated Bochs VGA card.

Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
2023-08-02 16:31:52 +08:00
Tom Rini
4e619e8d4f Merge tag 'u-boot-rockchip-20230731' of https://source.denx.de/u-boot/custodians/u-boot-rockchip
- Update dwc3 generic driver and update support for rk3568/rk3328;
- Add boards:
        rk3566: Pine64 Quartz64-A/B, SOQuartz on Model A/Blade/CM4-IO
        rk3568: Radxa E25 Carrier Board
        rk3588: Radxa ROCK5A
- Fixes and updates for chromebook veryon/jerry/speedy;
- SPI support fixes for rk3399/rk3568/rk3588;
- rk3588 usbdp phy support;
- dts and config updates for different boards;
2023-07-31 11:33:51 -04:00
Jonas Karlman
1f54f71b18 board: rockchip: Add Radxa E25 Carrier Board
Radxa E25 is a network application carrier board for the Radxa CM3I SoM
with a RK3568 SoC. It features dual 2.5G ethernet, mini PCIe, M.2 B Key,
USB3, eMMC, SD, nano SIM card slot and a 26-pin GPIO header.

Features tested on a Radxa E25 v1.4:
- SD-card boot
- eMMC boot
- USB host
- PCIe/Ethernet adapters is detected
- SATA

Device tree is imported from linux next-20230728.

Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: FUKAUMI Naoki <naoki@radxa.com>
2023-07-31 20:34:32 +08:00
Eugen Hristev
b8fc65473a board: rockchip: add Radxa ROCK5A Rk3588 board
ROCK 5A is a Rockchip RK3588S based SBC (Single Board Computer) by Radxa.

There are tree variants depending on the DRAM size : 4G, 8G and 16G.

Specifications:

     Rockchip Rk3588S SoC
     4x ARM Cortex-A76, 4x ARM Cortex-A55
     4/8/16GB memory LPDDR4x
     Mali G610MC4 GPU
     MIPI CSI 2 multiple lanes connector
     4-lane MIPI DSI connector
     Audio – 3.5mm earphone jack
     eMMC module connector
     uSD slot (up to 128GB)
     2x USB 2.0, 2x USB 3.0
     2x micro HDMI 2.1 ports, one up to 8Kp60, the other up to 4Kp60
     Gigabit Ethernet RJ45 with optional PoE support
     40-pin IO header including UART, SPI, I2C and 5V DC power in
     USB PD over USB Type-C
     Size: 85mm x 56mm (Raspberry Pi 4 form factor)

Kernel commits:
d1824cf95799 ("arm64: dts: rockchip: Add rock-5a board")
991f136c9f8d ("arm64: dts: rockchip: Update sdhci alias for rock-5a")
304c8a759953 ("arm64: dts: rockchip: Remove empty line from rock-5a")
cda0c2ea65a0 ("arm64: dts: rockchip: Fix RX delay for ethernet phy on rk3588s-rock5a")

Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-07-31 17:34:43 +08:00
Jonas Karlman
6855fa625c board: rockchip: Add Pine64 SOQuartz on CM4-IO
The Pine64 SOQuartz compute module is mostly pin-compatible with the RPi
CM4 form factor. Therefore, it can slot into the official Raspberry Pi
CM4 IO carrier board. Add this configuration to U-Boot.

Features tested with a SOQuartz 4GB v1.1 2022-07-11:
- SD-card boot
- eMMC boot
- USB host

Device tree is imported from linux v6.4.

Co-developed-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-07-31 14:41:36 +08:00
Jonas Karlman
d0026e5908 board: rockchip: Add Pine64 SOQuartz on Blade
The Pine64 SOQuartz Blade board is a carrier board for the SOQuartz
CM4-compatible compute module. It features PoE, an M.2 slot, an SD card
slot, HDMI, USB, serial and ethernet.

Features tested with a SOQuartz 4GB v1.1 2022-07-11:
- SD-card boot
- eMMC boot
- PCIe/NVMe
- USB host

Device tree is imported from linux v6.4.

Co-developed-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-07-31 14:41:35 +08:00
Jonas Karlman
651492bfb2 board: rockchip: Add Pine64 SOQuartz on Model A
The Pine64 SOQuartz Model A board is a carrier board for the SOQuartz
CM4-compatible compute module. It exposes PCIe, ethernet, USB, HDMI,
CSI, DSI, eDP and a 40 pin GPIO header, and is powered by 12V DC.

Features tested with a SOQuartz 4GB v1.1 2022-07-11:
- SD-card boot
- eMMC boot
- PCIe/NVMe/AHCI
- USB host

Device tree is imported from linux v6.4.

Co-developed-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-07-31 14:41:35 +08:00
Jonas Karlman
f52452bbea board: rockchip: Add Pine64 Quartz64-B Board
The Pine64 Quartz64 Model B is a credit-card sized single-board
computer based on the Rockchip RK3566 SoC. The board features an M.2
PCIe slot, USB3, USB2, eMMC, SD, ethernet, HDMI, analog audio out, a
40 pin GPIO header and a DSI and CSI port, as well as on-board Wi-Fi.

Features tested on a Quartz64-B 4GB v1.4 2022-06-06:
- SD-card boot
- eMMC boot
- SPI Flash boot
- PCIe/NVMe
- USB host

Device tree is imported from linux v6.4.

Co-developed-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-07-31 14:41:35 +08:00
Jonas Karlman
9c1b5d163e board: rockchip: Add Pine64 Quartz64-A Board
The Pine64 Quartz64 Model A is a single-board computer based on the
Rockchip RK3566 SoC. The board features USB3, SATA, PCIe, HDMI, USB2.0,
CSI, DSI, eDP, eMMC, SD, and an e-paper parallel port, as well as a
20 pin GPIO header.

Features tested on a Quartz64-A 8GB v2.0 2021-04-27:
- SD-card boot
- eMMC boot
- PCIe/NVMe/AHCI
- USB host

Device tree is imported from linux v6.4.

Co-developed-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-07-31 14:41:35 +08:00
Tom Rini
6544943819 Merge branch '2023-07-27-TI-K2-K3-updates'
- Resync some of the K3 DTS files with the kernel, and pull in some
  required related updates to keep drivers in sync with the dts files
  now.  Bring in some incremental fixes on top of one of the series I
  applied recently as well as updating the iot2050 platform.  Also do a
  few small updates to the K2 platforms.
2023-07-28 10:25:50 -04:00
Andrew Davis
5182e9c607 configs: keystone2: Change to using env files
Move to using .env file for setting up environment variables for K2x_evm.

Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2023-07-28 10:11:01 -04:00
Vignesh Raghavendra
3709b52915 env: ti: mmc.env: Move mmc related args to common place
All K3 SoCs use same set of args to load kernel for MMC. So move this to
common place to avoid duplication.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Reviewed-by: Nikhil M Jain <n-jain1@ti.com>
2023-07-28 10:11:01 -04:00
Jan Kiszka
badaa1f6a7 boards: siemens: iot2050: Unify PG1 and PG2/M.2 configurations again
This avoids having to maintain to defconfigs that are 99% equivalent.
The approach is to use binman to generate two flash images,
flash-pg1.bin and flash-pg2.bin. With the help of a template dtsi, we
can avoid duplicating the common binman image definitions.

Suggested-by: Andrew Davis <afd@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
2023-07-28 10:11:01 -04:00
Jan Kiszka
00e1c4549d boards: siemens: iot2050: Fix boot configuration
The common env bits now come via ti_armv7_common.env, include it.
Furthermore restore the board-specific boot targets and their ordering
that is now enforced k3-wide differently. Finally, enable
CONFIG_LEGACY_IMAGE_FORMAT explicitly which got lost while turning
FIT_SIGNATURE on by default for k3 devices.

Fixes: 53873974 ("include: armv7: Enable distroboot across all configs")
Fixes: 4ae1a247 ("env: Make common bootcmd across all k3 devices")
Fixes: 86fab110 ("Kconfig: Enable FIT_SIGNATURE if ARM64")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
2023-07-28 10:11:00 -04:00
Jonas Karlman
94da929b93 board: rockchip: Add Hardkernel ODROID-M1
Hardkernel ODROID-M1 is a single board computer with a RK3568B2 SoC,
a slightly modified version of the RK3568 SoC.

Features tested on a ODROID-M1 8GB v1.0 2022-06-13:
- SD-card boot
- eMMC boot
- SPI Flash boot
- PCIe/NVMe/AHCI
- SATA port
- USB host

Device tree is imported from linux v6.4.

Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Tested-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-07-28 18:45:03 +08:00
Christopher Obbard
0022461ba6 arm: rockchip: Add Radxa ROCK 4SE
Add board-specific devicetree/config for the RK3399T-based Radxa ROCK 4SE
board. This board offers similar peripherals in a similar form-factor to
the existing ROCK Pi 4B but uses the cost-optimised RK3399T processor
(which has different OPP table than the RK3399) and other minimal hardware
changes.

Kernel tag: next-20230719
Kernel commits:
- 86a0e14a82ea ("arm64: dts: rockchip: Add Radxa ROCK 4SE")

Signed-off-by: Christopher Obbard <chris.obbard@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-07-28 18:45:03 +08:00
Alex Bee
f83e0a2cd8 rockchip: evb_rk3229: Update/fix README
This updates the evb_rk3229's README on howto create / use the FIT image
created by binman.
Also fix some wrong paths and update filenames which have changed in recent
upstream optee-os versions.

Signed-off-by: Alex Bee <knaerzche@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-07-28 18:45:03 +08:00
Jagan Teki
0a3a5746c3 board: rockchip: Add Edgeble Neural Compute Module 6B
Neural Compute Module 6B(Neu6B) is a 96boards SoM-CB compute module
based on Rockchip RK3588J from Edgeble AI.

Add support for this SoM and IO board.

Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-07-28 18:45:02 +08:00
Tianling Shen
6a73211d4b rockchip: rk3568: Add support for FriendlyARM NanoPi R5C
FriendlyARM NanoPi R5C is an open-sourced mini IoT gateway device.

Specification:
- Rockchip RK3568
- 1/4GB LPDDR4X RAM
- 8/32GB eMMC
- SD card slot
- M.2 Connector
- 2x USB 3.0 Port
- 2x 2500 Base-T (PCIe, r8125)
- HDMI 2.0
- MIPI DSI/CSI
- USB Type C 5V

The device tree is taken from kernel v6.4-rc1.

Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Tianling Shen <cnsztl@gmail.com>
2023-07-28 18:45:02 +08:00
Tianling Shen
0ef326b5e9 rockchip: rk3568: Add support for FriendlyARM NanoPi R5S
FriendlyARM NanoPi R5S is an open-sourced mini IoT gateway device.

Board Specifications
- Rockchip RK3568
- 2 or 4GB LPDDR4X
- 8GB or 16GB eMMC, SD card slot
- GbE LAN (Native)
- 2x 2.5G LAN (PCIe)
- M.2 Connector
- HDMI 2.0, MIPI DSI/CSI
- 2xUSB 3.0 Host
- USB Type C PD, 5V/9V/12V
- GPIO: 12-pin 0.5mm FPC connector

The device tree is taken from kernel v6.4-rc1.

Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Tianling Shen <cnsztl@gmail.com>
2023-07-28 18:45:02 +08:00
Tianling Shen
9bd954ab8a rockchip: rk3328: Add support for Orange Pi R1 Plus LTS
The OrangePi R1 Plus LTS is a minor variant of OrangePi R1 Plus with
the on-board NIC chip changed from rtl8211e to yt8531c, and RAM type
changed from DDR4 to LPDDR3.

The device tree is taken from kernel v6.4-rc1.

Signed-off-by: Tianling Shen <cnsztl@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-07-28 18:45:02 +08:00
Tianling Shen
69e16c7b1c rockchip: rk3328: Add support for Orange Pi R1 Plus
Orange Pi R1 Plus is a Rockchip RK3328 based SBC by Xunlong.

This device is similar to the NanoPi R2S, and has a 16MB
SPI NOR (mx25l12805d). The reset button is changed to
directly reset the power supply, another detail is that
both network ports have independent MAC addresses.

The device tree and description are taken from kernel v6.3-rc1.

Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Tianling Shen <cnsztl@gmail.com>
2023-07-28 18:45:02 +08:00
Chris Morgan
ff27afedff board: rockchip: Add panel auto-detection for Anbernic RGxx3
Add support to automatically detect the panel for the Anbernic RGxx3.
This is done by creating a "pseudo driver" that provides only the bare
minimum to start the DSI controller and DSI DPHY. Once started, we then
can query the panel for its panel ID and compare it to a table of known
values. The panel compatible string (which corresponds to the upstream
Linux driver) is then defined as an environment variable "panel". The
panel compatible string is also changed automatically via an
ft_board_setup() call if what is detected differs from what is in the
loaded tree. This way, end users can use the same bootloader without
having to worry about which panel they have (as there is no obvious
way of knowing).

Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-07-28 18:45:02 +08:00
Chris Morgan
b190381418 board: rockchip: Add support for RG353PS to RGxx3
Add support for the RG353PS to the Anbernic RGxx3. This device is a
slightly pared down version of the RG353P with no eMMC, no touchscreen,
and only 1GB of RAM.

Refactor board logic so that all supported devices are defined with
ADC values and that future boards can be added by just defining the
board values in the device array.

Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-07-28 18:45:02 +08:00
Chris Morgan
3c057b4c6c rockchip: board: Update Odroid Go2 to Support Additional Revisions
Update the board.c file for the Odroid Go Advance to support the
Black Edition and the Odroid Go Super. The Odroid Go Advance Black
Edition differs from the original model with the addition of 2
extra buttons and an ESP8266 WiFi module. The Odroid Go Super
adds an additional 2 buttons compared to the Black Edition, along
with a larger panel and larger battery.

This change uses the value of ADC0 to determine which of these
3 models it is, and then changes the ${fdtfile} environment variable
to match the proper devicetree name in mainline Linux.

Tested on an Odroid Go Advance (first revision) and an Odroid Go Super.
The correct ${fdtfile} variable was set for each device.

Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-07-28 18:45:02 +08:00
Angelo Dureghello
74c521912a board: m68k add missing maintainer
Add myself as a maintainer for orphaned boards.
All these boards are covered by buildman m68k test.

Signed-off-by: Angelo Dureghello <angelo@kernel-space.org>
2023-07-25 23:21:42 +02:00
Andrew Davis
fa59771039 MAINTAINERS: Take maintainership of TI KeyStone2 support
Add arch/arm/mach-keystone/ into K2 board directory MAINTAINERS file.

Convert current entries into regex match style.

Assign maintainership to myself.

Signed-off-by: Andrew Davis <afd@ti.com>
2023-07-25 13:29:00 -04:00
Tom Rini
fdfbd70da6 MAINTAINERS: Add some missing directories or files
In a few cases we have MAINTAINERS entries that are missing obvious
paths or files. Typically this means a board directory that did not list
itself, but in a few cases we have a Kconfig file or similar.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2023-07-25 12:44:47 -04:00
Tom Rini
b99476e71a MAINTAINERS: Deal with '+' in paths
The listed paths are allowed to contain wildcards.  This includes the
'+' character which we have as a literal part of the path in a few
cases. Escape the '+' here so that files are matched.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2023-07-25 12:44:47 -04:00
Tom Rini
5f1720f282 MAINTAINERS: Fix path typos and similar
We have a number of cases where the in-tree path of files and where
they presumably were when the first version of a patch were posted
differ slightly.  Correct these to point at where the files are now.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2023-07-25 12:44:47 -04:00
Tom Rini
f23f1b5307 MAINTAINERS: Add a number of "common" directories
A number of platforms have "common" directories that are in turn not
listed by the board MAINTAINERS file.  Add these directories in many
cases.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2023-07-25 12:44:47 -04:00
Tom Rini
bded724104 xes: Remove leftover code
The platforms here have been removed, but the common code directory was
forgotten.  Clean up.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2023-07-25 12:44:47 -04:00
Tom Rini
4835e86cba arm: Remove leftover MAINTAINERS files
These platforms have been removed, but the MAINTAINERS file was missed,
clean up.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2023-07-25 12:44:47 -04:00
Tom Rini
1f2e4027fa arm: Remove more remnants of bcmcygnus
Remove some leftover files from the bcmcygnus platform.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2023-07-25 12:44:47 -04:00
Tom Rini
d38ed5b68c sunxi: Add MAINTAINERS entry for Lctech Pi F1C200s
This defconfig was added without a MAINTAINERS entry, add one.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2023-07-25 12:44:47 -04:00
Tom Rini
2b506407c8 rockchip: Add MAINTAINERS entry for Radxa Rock 4C+
This defconfig was added without a MAINTAINERS entry, add one.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2023-07-25 12:44:47 -04:00
Tom Rini
e5478bef26 MAINTAINERS: Add some missing defconfig files to existing entries
We have a few places where defconfigs were added (or renamed) and not
included in their previously listed MAINTAINERS entry, correct this.

Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by:  Adam Ford <aford173@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2023-07-25 12:44:47 -04:00
Tom Rini
aaf929a55f MAINTAINERS: Correct minor mistakes on some file listings
There are a few entries where minor mistakes mean that we don't match up
with obviously expected files, correct those.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2023-07-25 12:44:47 -04:00
Manorit Chawdhry
d5b1ef30d7 board: ti: keys: add .key and .crt for fit signature signing
Fit signature mechanism through the standards require the presence of
.key and .crt in the folder with the same name, since we are using our
custMpk only for the signing, update the format to that of standards to
be compatible for packaging easily.

Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
2023-07-21 22:07:46 -04:00
Andrew Davis
014e013e78 environment: ti: Make get_fdt_mmc common
Since get_fdt_mmc is common, factor it out into mmc.env and remove
it from each platform env file along with changing the directory path to
reflect the standards. Use it in mmcloados but keep loadfdt
defined in case it is still used by some external uEnv.txt script.

Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
2023-07-21 20:35:50 -04:00
Andrew Davis
d8ea68da6b environment: ti: Prefix ARM64 DTB names with directory
In Linux the ARM64 DTSs are stored in vendor directories to help organize
the files and prevent naming collisions. The deployed DTBs will mirror
this and so the vendor prefix should be added to the variable used to
locate these files.

Suggested-by: Ryan Eatmon <reatmon@ti.com>
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Reviewed-by: Nikhil M Jain <n-jain1@ti.com>
2023-07-21 20:35:50 -04:00
Kamlesh Gurudasani
40e09b6afb board: ti: am64x: am64x.env: set fdtfile env variable
Set fdtfile env variable similar to other k3 socs.

Signed-off-by: Kamlesh Gurudasani <kamlesh@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Reviewed-by: Nikhil M Jain <n-jain1@ti.com>
2023-07-21 19:37:57 -04:00
Neha Malcom Francis
1ee652ab2f doc: board: ti: Update documentation for binman flow
Earlier documentation specified builds for generating bootloader images
using an external TI repository k3-image-gen and core-secdev-k3. Modify
this to using the binman flow so that user understands how to build the
final boot images.

Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
2023-07-21 19:36:59 -04:00
Neha Malcom Francis
6d6228ab8f am62a: dts: binman: Package tiboot3.bin, tispl.bin, u-boot.img
Support added for HS-SE, HS-FS and GP boot binaries for AM62ax.

HS-SE:
    * tiboot3-am62ax-hs-evm.bin
    * tispl.bin
    * u-boot.img

HS-FS:
    * tiboot3-am62ax-hs-fs-evm.bin
    * tispl.bin
    * u-boot.img

GP:
    * tiboot3.bin --> tiboot3-am62ax-gp-evm.bin
    * tispl.bin_unsigned
    * u-boot.img_unsigned

It is to be noted that the bootflow followed by AM62ax requires:

tiboot3.bin:
	* R5 SPL
	* R5 SPL dtbs
	* TIFS
	* board-cfg
	* pm-cfg
	* sec-cfg
	* rm-cfg

tispl.bin:
	* DM
	* ATF
	* OP-TEE
	* A72 SPL
	* A72 SPL dtbs

u-boot.img:
	* A72 U-Boot
	* A72 U-Boot dtbs

Reviewed-by: Simon Glass <sjg@chromium.org>
[afd@ti.com: changed output binary names appropriately]
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
2023-07-21 19:36:59 -04:00
Neha Malcom Francis
01e0127753 am62a: yaml: Add board configs for AM62ax
Added YAML configs for AM62ax

Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
2023-07-21 19:36:59 -04:00
Neha Malcom Francis
ce46f51990 am625: dts: binman: Package tiboot3.bin, tispl.bin and u-boot.img
Support added for HS-SE, HS-FS and GP boot binaries for AM62.

HS-SE:
    * tiboot3-am62x-hs-evm.bin
    * tispl.bin
    * u-boot.img

HS-FS:
    * tiboot3-am62x-hs-fs-evm.bin
    * tispl.bin
    * u-boot.img

GP:
    * tiboot3.bin --> tiboot3-am62x-gp-evm.bin
    * tispl.bin_unsigned
    * u-boot.img_unsigned

It is to be noted that the bootflow followed by AM62 requires:

tiboot3.bin:
	* R5 SPL
	* R5 SPL dtbs
	* TIFS
	* board-cfg
	* pm-cfg
	* sec-cfg
	* rm-cfg

tispl.bin:
	* DM
	* ATF
	* OP-TEE
	* A72 SPL
	* A72 SPL dtbs

u-boot.img:
	* A72 U-Boot
	* A72 U-Boot dtbs

Reviewed-by: Simon Glass <sjg@chromium.org>
[afd@ti.com: changed output binary names appropriately]
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
2023-07-21 19:36:59 -04:00
Neha Malcom Francis
0eba798b41 am62: yaml: Add board configs for AM62
Added YAML configs for AM62

Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
2023-07-21 19:36:58 -04:00
Neha Malcom Francis
106589aae7 j721s2: dts: binman: Package tiboot3.bin, tispl.bin and u-boot.img
Support has been added for both HS-SE, HS-FS  and GP images.

HS-SE:
    * tiboot3-j721s2-hs-evm.bin
    * tispl.bin
    * u-boot.img

HS-FS:
    * tiboot3-j721s2-hs-fs-evm.bin
    * tispl.bin
    * u-boot.img

GP:
    * tiboot3.bin --> tiboot3-j721s2-gp-evm.bin
    * tispl.bin_unsigned
    * u-boot.img_unsigned

It is to be noted that the bootflow followed by J721S2 requires:

tiboot3.bin:
	* R5 SPL
	* R5 SPL dtbs
	* TIFS
	* board-cfg
	* pm-cfg
	* sec-cfg
	* rm-cfg

tispl.bin:
	* DM
	* ATF
	* OP-TEE
	* A72 SPL
	* A72 SPL dtbs

u-boot.img:
	* A72 U-Boot
	* A72 U-Boot dtbs

Reviewed-by: Simon Glass <sjg@chromium.org>
[afd@ti.com: changed output binary names appropriately]
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
2023-07-21 19:36:58 -04:00
Neha Malcom Francis
267a4845c9 j721s2: yaml: Add board configs for J721S2
Added YAML configs for J721S2

Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
2023-07-21 19:36:58 -04:00
Neha Malcom Francis
1bc527e8f4 am64x: dts: binman: Package tiboot3.bin, tispl.bin u-boot.img
Support added for HS and GP boot binaries for AM64x.

HS-SE:
    * tiboot3-am64x_sr2-hs-evm.bin
    * tispl.bin
    * u-boot.img

HS-FS:
    * tiboot3-am64x_sr2-hs-fs-evm.bin
    * tispl.bin
    * u-boot.img

GP:
    * tiboot3.bin --> tiboot3-am64x-gp-evm.bin
    * tispl.bin_unsigned
    * u-boot.img_unsigned

Note that the bootflow followed by AM64x requires:

tiboot3.bin:
	* R5 SPL
	* R5 SPL dtbs
	* sysfw
	* board-cfg
	* pm-cfg
	* sec-cfg
	* rm-cfg

tispl.bin:
	* ATF
	* OP-TEE
	* A53 SPL
	* A53 SPL dtbs

u-boot.img:
	* A53 U-Boot
	* A53 U-Boot dtbs

Reviewed-by: Simon Glass <sjg@chromium.org>
[afd@ti.com: changed output binary names appropriately]
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
2023-07-21 19:36:58 -04:00
Neha Malcom Francis
640bf9dd8e am64x: yaml: Add board configs for AM64x
Added YAML configs for AM64xx

Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
2023-07-21 19:36:58 -04:00
Neha Malcom Francis
77c29cb1b6 am65: dts: binman: Package tiboot3.bin, sysfw.itb, tispl.bin, u-boot.img
Support has been added for both HS-SE(SR 2.0) and GP(SR 2.0) images.

HS-SE:
	* tiboot3-am65x_sr2-hs-evm.bin
	* sysfw-am65x_sr2-hs-evm.itb
	* tispl.bin
	* u-boot.img

GP:
	* tiboot3.bin --> tiboot3-am65x_sr2-gp-evm.bin
	* sysfw.itb --> sysfw-am65x_sr2-gp-evm.itb
	* tispl.bin_unsigned
	* u-boot.img_unsigned

Note that the bootflow followed by AM65x requires:

tiboot3.bin:
	* R5 SPL
	* R5 SPL dtbs
sysfw.itb:
	* sysfw
	* board-cfg
	* pm-cfg
	* sec-cfg
	* rm-cfg

tispl.bin:
	* ATF
	* OP-TEE
	* A53 SPL
	* A53 SPL dtbs

u-boot.img:
	* A53 U-Boot
	* A53 U-Boot dtbs

Reviewed-by: Simon Glass <sjg@chromium.org>
[afd@ti.com: changed output binary names appropriately]
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
2023-07-21 19:36:58 -04:00
Neha Malcom Francis
27ebb1517f am65x: yaml: Add AM65x board config files
Added YAML configs for AM65x

Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
2023-07-21 19:36:58 -04:00
Neha Malcom Francis
ca5f1e25e5 j7200: dts: binman: Package tiboot3.bin, tispl.bin, u-boot.img
Support has been added for both HS-SE(SR 2.0), HS-FS(SR 2.0) and GP
images.

HS-SE:
	* tiboot3-j7200_sr2-hs-evm.bin
	* tispl.bin
	* u-boot.img

HS-FS:
	* tiboot3-j7200_sr2-hs-fs-evm.bin
	* tispl.bin
	* u-boot.img

GP:
	* tiboot3.bin --> tiboot3-j7200-gp-evm.bin
	* tispl.bin_unsigned
	* u-boot.img_unsigned

It is to be noted that the bootflow followed by J7200 requires:

tiboot3.bin:
	* R5 SPL
	* R5 SPL dtbs
	* TIFS
	* board-cfg
	* pm-cfg
	* sec-cfg
	* rm-cfg

tispl.bin:
	* DM
	* ATF
	* OP-TEE
	* A72 SPL
	* A72 SPL dtbs

u-boot.img:
	* A72 U-Boot
	* A72 U-Boot dtbs

Reviewed-by: Simon Glass <sjg@chromium.org>
[afd@ti.com: changed output binary names appropriately]
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
2023-07-21 19:36:58 -04:00
Neha Malcom Francis
e6135b0614 j7200: yaml: Add J7200 board config files
Added YAML configs for J7200

Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
2023-07-21 19:36:58 -04:00
Neha Malcom Francis
177178685a j721e: dts: binman: Package tiboot3.bin, sysfw.itb, tispl.bin, u-boot.img
By providing entries in the binman node of the device tree, binman will
be able to find and package board config artifacts generated by
TIBoardConfig with sysfw.bin and generate the final image sysfw.itb.
It will also pick out the R5 SPL and sign it with the help of TI signing
entry and generate the final tiboot3.bin.

Entries for A72 build have been added to k3-j721e-binman.dtsi to
generate tispl.bin and u-boot.img.

Support has been added for both HS-SE(SR 1.1), HS-FS(SR 2.0) and GP images
In HS-SE, the encrypted system firmware binary must be signed along with
the signed certificate binary.

HS-SE:
	* tiboot3-j721e_sr1_1-hs-evm.bin
	* sysfw-j721e_sr1_1-hs-evm.itb
	* tispl.bin
	* u-boot.img

HS-FS:
	* tiboot3-j721e_sr2-hs-fs-evm.bin
	* sysfw-j721e_sr2-hs-fs-evm.itb
	* tispl.bin
	* u-boot.img

GP:
	* tiboot3.bin -->tiboot3-j721e-gp-evm.bin
	* sysfw.itb --> sysfw-j721e-gp-evm.itb
	* tispl.bin_unsigned
	* u-boot.img_unsigned

It is to be noted that the bootflow followed by J721E requires:

tiboot3.bin:
	* R5 SPL
	* R5 SPL dtbs

sysfw.itb:
	* TIFS
	* board-cfg
	* pm-cfg
	* sec-cfg
	* rm-cfg

tispl.bin:
	* DM
	* ATF
	* OP-TEE
	* A72 SPL
	* A72 SPL dtbs

u-boot.img:
	* A72 U-Boot
	* A72 U-Boot dtbs

Reviewed-by: Simon Glass <sjg@chromium.org>
[afd@ti.com: changed output binary names appropriately]
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
2023-07-21 19:36:58 -04:00
Neha Malcom Francis
11ee37962e j721e: schema: yaml: Add general schema and J721E board config files
Schema file in YAML must be provided in board/ti/common for validating
input config files and packaging system firmware. The schema includes
entries for rm-cfg, board-cfg, pm-cfg and sec-cfg.

Board config files must be provided in board/ti/<devicename> in YAML.
These can then be consumed for generation of binaries to package system
firmware. Added YAML configs for J721E in particular.

Signed-off-by: Tarun Sahu <t-sahu@ti.com>
[n-francis@ti.com: prepared patch for upstreaming]
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
2023-07-21 19:36:58 -04:00
Neha Malcom Francis
78144826bb binman: ti-secure: Add support for TI signing
The ti-secure entry contains certificate for binaries that will be
loaded or booted by system firmware whereas the ti-secure-rom entry
contains certificate for binaries that will be booted by ROM. Support
for both these types of certificates is necessary for booting of K3
devices.

Reviewed-by: Simon Glass <sjg@chromium.org>
[vigneshr@ti.com: fixed inconsist cert generation by multiple packing]
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
2023-07-21 19:36:58 -04:00
Nikhil M Jain
12fdacea5a board: ti: am62x: evm: Update function calls for splash screen
Use spl_dcache_enable, in place of setup_dram, arch_reserve_mmu to set
up pagetable, initialise DRAM and enable Dcache to avoid multiple
function calls.

Check for CONFIG_SPL_VIDEO in place of CONFIG_SPL_VIDEO_TIDSS to prevent
any build failure in case video config is not defined and video related
functions are called.

Check for CONFIG_SPL_SPLASH_SCREEN and CONFIG_SPL_BMP before calling
splash_display to avoid compilation failure.

Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
2023-07-21 15:32:12 -04:00
Nikhil M Jain
eeea6e298d board: ti: am62x: evm: Include necessary header files
At the time of compilation evm.c gives below warning for implicit
declaration of enable_caches, to mitigate this include cpu_func.h.

board/ti/am62x/evm.c: In function ‘spl_board_init’:
board/ti/am62x/evm.c:90:9: warning: implicit declaration of function ‘enable_caches’ [-Wimplicit-function-declaration]
90 |         enable_caches();

Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
2023-07-21 13:13:41 -04:00
Michal Simek
174d728471 arm64: zynqmp: Switch to amd.com emails
Update my and DPs email address to match current setup.

Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/aba5b19b9c5a95608829e86ad5cc4671c940f1bb.1688992543.git.michal.simek@amd.com
2023-07-21 09:00:38 +02:00
Ashok Reddy Soma
9a45365ae9 arm64: versal-net: spi: Update boot sequence dynamically
Currently xspi0 is used for all spi boot modes, it means it will use "sf
probe 0 0 0" for all spi's irrespective of which node it is wired.

Get boot sequence from dev_seq() and update boot command for xspi
dynamically.

As a result bootcmd for spi is updated as below when two instances of spi
are present in DT node.
bootcmd_xspi0=devnum_xspi=0; run xspi_boot
bootcmd_xspi1=devnum_xspi=1; run xspi_boot

xspi_boot=sf probe $devnum_xspi:0 0 0 && sf read $scriptaddr
$script_offset_f $script_size_f && echo XSPI: Trying to boot script at
${scriptaddr} && source ${scriptaddr}; echo XSPI: SCRIPT FAILED:
continuing...;

Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230614093058.30438-1-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
2023-07-21 09:00:38 +02:00
Algapally Santosh Sagar
340760ec0f xilinx: zynq: Add the missing function prototypes
Add the missing prototypes for the functions pointed by the below
sparse warnings
warning: no previous prototype for 'set_dfu_alt_info'
[-Wmissing-prototypes]
warning: no previous prototype for 'board_debug_uart_init'
[-Wmissing-prototypes]

Signed-off-by: Algapally Santosh Sagar <santoshsagar.algapally@amd.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230614090359.10809-7-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
2023-07-21 09:00:38 +02:00
Algapally Santosh Sagar
3bfc94ba9c arm: zynq: Pass the missing argument type in function definition
Pass missing argument type in the function definition to fix the
sparse warning, warning: old-style function definition
[-Wold-style-definition]

Signed-off-by: Algapally Santosh Sagar <santoshsagar.algapally@amd.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230614090359.10809-6-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
2023-07-21 09:00:38 +02:00
Tom Rini
5dcfc99b2b Merge tag 'fsl-qoriq-2023-7-13' of https://source.denx.de/u-boot/custodians/u-boot-fsl-qoriq
Enable DM_SERIAL for T2080RDB, T4240RDB, T1042D4RDB, T1024RDB
2023-07-19 07:59:34 -04:00
Simon Glass
92ccaf7d97 sandbox: Install ACPI tables on startup
With x86 we set up the ACPI tables on startup so they can be examined. Do
the same with sandbox, so it is consistent.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2023-07-17 17:23:15 +08:00
Simon Glass
f52a7f0537 sandbox: Correct header order in board file
Fix the header order in this file.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2023-07-17 17:23:15 +08:00
Simon Glass
603363927a bios_emulator: Add Kconfig and adjust Makefile for SPL
The Kconfig for this is currently inside a particular board. Move it into
the correct place and allow use in SPL, so that video can be used there
if needed.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2023-07-17 17:08:44 +08:00
Jim Liu
4b7f29ff14 arch: arm: npcm8xx: add cpu version and 4G ram support
Add npcm8xx A2 cpu version check
and add 4G RAM support

Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
2023-07-14 12:52:18 -04:00
Jim Liu
68f107a42b board: nuvoton: arbel: change uboot load address
use new memory layout and change uboot load address.
open tpm, tee and more config feature

No need to reserve top memory because the reserved space
is moved to the bottom area of memory.

Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
2023-07-14 12:52:18 -04:00
Jim Liu
178284a9cf board: nuvoton: add env setting for boot to linux
add console and mem env to boot to linux kernel

Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
2023-07-14 12:52:18 -04:00
Tom Rini
c990ecba4d Merge https://gitlab.denx.de/u-boot/custodians/u-boot-marvell
- mvebu: Thecus: Misc enhancement and cleanup (Tony)
- mvebu: Add AC5X Allied Telesis x240 board support incl NAND
  controller enhancements for this SoC (Chris)
2023-07-13 20:38:50 -04:00
Tom Rini
f6da5e9273 u-boot-imx-20230713
-------------------
 
 Merge for 2023.10.
 
 CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/16888
 -----BEGIN PGP SIGNATURE-----
 
 iG0EABECAC0WIQS2TmnA27QKhpKSZe309WXkmmjvpgUCZK/m8A8cc2JhYmljQGRl
 bnguZGUACgkQ9PVl5Jpo76ZuIwCglKZeAdyoF4Y3mFGLQsl5woOCqIkAn2bJdqnA
 cYelsWxQgHWLMNxbNHjG
 =91LJ
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-imx-20230713' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx

u-boot-imx-20230713
-------------------

Merge for 2023.10.

CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/16888
2023-07-13 20:38:24 -04:00
Chris Packham
4c97c4b590 arm: mvebu: Add Allied Telesis x240 board
The x240 and SE240 are a series of L2+ switches from Allied Telesis.
There are a number of them in the range but as far as U-Boot is
concerned all the CPU block components are the same so there's only one
board defined.

Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2023-07-13 15:53:57 +02:00
Fabio Estevam
cdbef023e2 mx7dsabresd: Retrieve the second MAC address from fuses
Currently, a random MAC address is assigned to eth1 in Linux.

Fix this behavor by retrieving the second MAC address from the fuses.

Signed-off-by: Fabio Estevam <festevam@denx.de>
2023-07-13 11:58:18 +02:00