Add function and new command "auth_cntr" for secure boot support.
When booting with life cycle set to OEM closed, we need to use
this function to authenticate the OS container and load kernel & FDT
from OS container to their destination.
Also add image authentication call when loading container images.
Users can set CONFIG_AHAB_BOOT=y to enable the feature. It is not
set at default.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Enable bd71837 pmic for i.MX8MM EVK board, need to set voltage for
DRAM and linux suspend voltage requirement.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
It will be easy to separate SD/EMMC when booting in SPL stage, then
no need to bother which device is BOOT_DEVICE_MMC1/2.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add init_nand_clk to enable gpmi nand clock. Since i.MX8MQ not use CCF,
so we still use legacy mode to configure the clock.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The i.MX8MQ B1 uses OCOTP_HW_OCOTP_READ_FUSE_DATA register for chip id.
It returns a magic number 0xff0055aa. update get_cpu_rev to support it,
and enable ocotp clock to access ocotp.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Migrate to DM_VIDEO, update the device tree and remove code that is no
longer necessary.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Migrate to DM_ETH and remove code that is no longer necessary.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
This updates the i.MX8MQ device trees and, necessarily, also the
i.MX8MQ clock bindings. These are taken verbatim from from the
Linux kernel version v5.4-rc2, which three small changes which
were already part of the previous device tree:
* Keep the PSCI reserved memory range
* Keep the alias for ethernet, so that the MAC address can be set
* Keep the modified #include for the IOMUXC pins
Signed-off-by: Patrick Wildt <patrick@blueri.se>
Acked-by: Peng Fan <peng.fan@nxp.com>
This commit converts mccmon6's u-boot proper (in a single commit to avoid
build breaks) to use solely DM/DTS.
The DTS description of the mccmon6 has been ported from Linux kernel
(v4.20, SHA1: 8fe28cb58bcb235034b64cbbb7550a8a43fd88be)
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Add u-boot,dm-pre-reloc properties for uart pinmux configuration
nodes, which enables UART as early as possible (before relocation).
Without this we miss almost the half of output (U-boot version,
CPU defails, Reset cause, DRAM details etc.).
Fixes: cd69e8ef9b ("colibri-imx6ull: migrate pinctrl and regulators to dtb/dm")
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Introduce imx6ull-colibri-u-boot.dtsi for u-boot specific properties to
keep original imx6ull-colibri.dts in sync with Linux.
Move all contents of imx6ull-colibri.dts to imx6ull-colibri.dtsi +
additionally fix checkpatch warnings.
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
According to IMX28CEC rev. 4, 10/2018, Table 15. Recommended Operating
Conditions, page 16, the VDDD should be set to 1.55V when the CPU is
operating at 454MHz. This is the case in U-Boot, hence increase the
VDDD voltage. This fixes instability when performing TFTP transfers.
Increase the brownout threshold to 1.4V. The documentation recommends
1.45V setting for the brownout, however, this triggers failure during
power block init, so keep the brownout slightly lower.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
imx6_is_bmode_from_gpr9 always returns false, because
IMX6_SRC_GPR10_BMODE is 1<<28 and gets casted to u8 on return.
This moves the function body into imx6_src_get_boot_mode, since that is the
only one using it and it is on the same abstraction level (accessing
registers directly).
Signed-off-by: Claudius Heine <ch@denx.de>
Introduce disable_ipu_clock(). This is done in preparation for
configuring the NoC registers on i.MX6QP in SPL.
Afer the NoC registers are set the IPU clocks can be disabled.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The code can be made simpler by using setbits_le32(), so switch
to it.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
We already a message indicating that U-Boot is about to jump to SPL, so
make this one a debug() to reduce code size.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
We don't need to do this and it is done (in more detail) in U-Boot proper.
Drop this to save code space.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present we call spl_init() before identifying the CPU. This is not a
good idea - e.g. if bootstage is enabled then it will try to set up the
timer which works better if the CPU is identified.
Put explicit code at each entry pointer to identify the CPU.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
For TPL we only need to set up the features and identify the CPU to a
basic level. Add a function to handle that.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
In TPL we try to minimise code size so do not include the PCI subsystem.
We can use fixed BARs and drivers can directly program the devices that
they need.
However we do need to bind the devices on the PCI bus and without PCI this
does not ordinarily happen. As a work-around, define a fake PCI bus which
does this binding, but no other PCI operations. This is a convenient way
to ensure that we can use the same device tree for TPL, SPL and U-Boot
proper:
TPL - CONFIG_TPL_PCI is not set (no auto-config, fake PCI bus)
SPL - CONFIG_SPL_PCI is set (no auto-config but with real PCI bus)
U-Boot - CONFIG_PCI is set (full auto-config after relocation)
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The x86 power unit handles power management. Support initing this device
which is modelled as a new type of system controller since there are no
operations needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present the value of the timer base is used to determine whether the
timer has been set up or not. It is true that the timer is essentially
never exactly 0 when it is read. However 'time 0' may indicate the time
that the machine was reset so it is useful to be able to denote that.
Update the code to use a separate flag instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Aiden Park <aiden.park@intel.com>
Reviewed-by: Aiden Park <aiden.park@intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
ARC fixes for v2020.01-rc2
The main change is move to DM_MMC of yet 2 another ARC boards:
AXS101 & IoTDK.
Among that we improve handling of stock-formatted SD-cards of high volume
on EM SDP as well as introduction of reset driver for HSDK which is required
for prepser reinitialization of some peripherals like USB etc.
Bootstage improvements for TPL, SPL
Various sandbox and dm improvements and fixes
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl24zDoRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreZRiwf+Mf7oG//zjiZcHaPP6KOFb1CjwqLSuiaI
eCYB6GEZXuSpc8MjAw+baAfIw8MMFuaCfPsUQ5dDo391neK0sW9kkEsdcXnQBpB3
GdJYcewLN1UuJZovriGobIisGc0GQHh8gmRcVGWSKoEt+gAQauRtVYBIUPuS3JG+
ihZgYmVgICa+3tqavIbP2oZdXLuLAxR65mfiQHtiJwdCN3OOzyls2v0T0slQX9GV
ln6EvTk8OMIudBmkB7YiTmJF7AB+3PH/uBaiYyTKO9gtjLhnmCFvG5HxJTRFOKvU
F4oVWZJDEcqfZvYgWg8i5vgokMP41nzLfBr7j5ifUX1f3xwCHy/Tpw==
=S4XI
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-29oct19' of git://git.denx.de/u-boot-dm
- Fix for patman with email addresses containing commas
- Bootstage improvements for TPL, SPL
- Various sandbox and dm improvements and fixes
Add get_timer_us(), which is useful e.g. when we need higher
precision timestamps.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
[trini: Fixup arch/arm/mach-bcm283x/include/mach/timer.h]
Signed-off-by: Tom Rini <trini@konsulko.com>
- Add I2C clocks for i.MX6Q CCF driver
- Fix check in clk_set_default_parents()
- Managed API to get clock from device tree
- Fixes for core clock code (including sandbox regression tests)
At present some boards generate kwbimage.cfg in the source tree
during the build. This breaks buildman testing on some systems
where the source tree is read-only. Update makefile rules to
generate it in the build tree instead.
Note some other boards have the kwbimage.cfg file written in
advance, hence we need check if the file exists in the build
tree first, otherwise we fall back to one in the source tree.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
This function needs a prototype so that tests can use it. Add one.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This function writes to its address so the address should not be declared
as const. Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
- bmips: various small fixes
- mtmips: add new drivers for clock, reset-controller and pinctrl
- mtmips: add support for high speed UART
- mtmips: update/enhance drivers for SPI and ethernet
- mtmips: add support for MMC
-----BEGIN PGP SIGNATURE-----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=6G/J
-----END PGP SIGNATURE-----
Merge tag 'mips-pull-2019-10-25' of git://git.denx.de/u-boot-mips
- bmips: add BCRM NAND support for BCM6368, BCM6328, BCM6362 and BCM63268 SoCs
- bmips: various small fixes
- mtmips: add new drivers for clock, reset-controller and pinctrl
- mtmips: add support for high speed UART
- mtmips: update/enhance drivers for SPI and ethernet
- mtmips: add support for MMC
Add the address spaces for the R5F cores in MCU domain to the ranges
property of the cbass_mcu interconnect node so that the addresses
within the R5F nodes can be translated properly by the relevant OF
address API.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
In SPL, DDR should be made available by the end of board_init_f()
so that apis in board_init_r() can use ddr. Adding support for
triggering DDR initialization from board_init_f().
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Use the 3733MTs DDR configuration that is auto generated from
DDR_Regconfig tool.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Kevin Scholz <k-scholz@ti.com>
Added the following registers to the DDR configuration:
- ACIOCR0,
- ACIOCR3,
- V2H_CTL_REG,
- DX8SLxDQSCTL.
Modified enable_dqs_pd and disable_dqs_pd to only touch the associated
bit fields for pullup and pulldown registers (to preserve slew rate and
other bits in that same register). Also update the dts files in the same
patch to maintain git bisectability.
Signed-off-by: James Doublesin <doublesin@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The current configuration of DDR on AM654 base board is for 1600MTs but
the file name is specified as k3-am654-base-board-ddr4-1600MHz.dtsi.
Since 1600MHz is misleading, rename it to
k3-am654-base-board-ddr4-1600MTs.dtsi
Signed-off-by: James Doublesin <doublesin@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
U-Boot cleans and invalidate L1 and L2 caches before jumping to Linux
by set/way in cleanup_before_linux(). Additionally there is a custom
hook provided to clean and invalidate L3 cache.
Unfortunately on K3 devices(having a coherent architecture), there is no
easy way to quickly clean all the cache lines for L3. The entire address
range needs to be cleaned and invalidated by Virtual Address. This can
be implemented using the L3 custom hook but it take lot of time to clean
the entire address range. In the interest of boot time this might not be
a viable solution.
The best hit is to make sure the loaded Linux image is flushed so that
the entire image is written to DDR from L3. When Linux starts running with
caches disabled the full image is available from DDR.
Reported-by: Andrew F. Davis <afd@ti.com>
Reported-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Once the arch specific boot_prepare_linux completes, boards wants to
have a custom preparation for linux. Add support for a custom
board_prep_linux.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add usb peripheral and usb phy nodes in spl to enable SPL_DFU bootmode.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdspnqAAoJEB6zHgIOrC/Ixi4IAJEEiCZPu6Z3fbkFX/Um7vCX
eMTltJN8nz4oiSi3xdx3ejueqWdW3F8VuCkHb0j0bVAhMlUlVgwCzfd0cD+D2iwS
jkrgzASNAr+JeYKYEdWqqfaUxOCd2qfuBu9EXlpvKQLWLt+KRfsOsHWcgR4bf095
aGCihvd/fKhKYUvbf5cEQnsWa3UwtsKk4Web5MKjxXx3p0iVNlu4KLd/vDWfTios
X1NqiO5ZjXNrDxyG6Aj8lgDXlE5kfeKaN/aCJU1/0U2cXm8JRu2w2dv1P/e/kU+j
NHIGzICAG4Lk/4gQTeuohJxLyvj7K3i1H12ik9Qeh4H1/5fsyybyltGUo7H443s=
=JYe3
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2020.01-b' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
Second set of u-boot-atmel features and fixes for 2020.01 cycle
This feature set includes Eugen's work on a new tiny flexcom driver and
eeprom mac retrieval for the sam9x60-ek board.
Some drivers (clk, pinctrl, reset, ...) are necessary for reset of the
system, they should be always selected.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds default eth pinctrl for all boards.
There are two pinctrl nodes used for two scenarios:
ephy_iot_mode - for IOT boards which have only one port (PHY0)
ephy_router_mode - For routers which have more than one ports
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds default p0led status and phy0 link polling for all boards.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
All three UARTs of mt7628 are actually MediaTek's high-speed UARTs which
support baudrate up to 921600.
The high-speed UART is compatible with ns16550 when baudrate <= 115200.
Add compatible string to dtsi file so u-boot can use it when serial_mtk
driver is built in.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
The UART of MT7628 has fixed 40MHz input clock so there is no need to put
clock-frequency in every dts files. Just put it into the common dtsi file.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
If configuration is set to skip low level init, automatic
probe of L2 cache size is not performed and the size is set to 0.
Flushing or invalidating the L2 cache will fail in this case.
Add a static configuration (SYS_DCACHE_LINE_SIZE) with default set to 0.
Signed-off-by: Ramon Fried <rfried.dev@gmail.com>
The Allwinner H6 SoC has a register to set the PIO banks' voltage. When
it mismatches the real voltage supplied to the VCC to the PIO supply,
the PIO will work improperly.
The PIO controller also has a register that contains the status of each
VCC rail of the PIO supplies, and it has the same definition with the
configuration register. so we can just copy the content of this register
to the configuration register at startup, to ensure the configuration is
correct at startup stage.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
[jagan: s/__maybe__unused/__maybe_unused]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Sync Kernel DTS for Allwinner H6 boards.
Drop /omit-if-no-ref/ keyword as it's not supported by U-boot.
commit <d45331b00ddb> Linux 5.3-rc4
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
clock_sun6i.c is used for sun6i, sun8i and sun50i SoC families.
PLL1 clock sets the default system clock, defined as:
sun6i: 1008000000
sun8i: 1008000000
sun50i: 816000000
With the current calculation, m = 2 and k = 3. Solving for n,
this results 28. Solving back:
(24MHz * 28 * 3) / 2 = 1008MHz
However if the requested clock is 816, n is 22.66 rounded
to 22, which results:
(24MHz * 28 * 3) / 2 = 792MHz
Changing k to 4 satisfies both system clocks:
(24E6 * 21 * 4) / 2 = 1008MHz
(24E6 * 17 * 4) / 2 = 816MHz
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
A64 OLinuXino board from Olimex has three variants with onboard eMMC:
A64-OLinuXino-1Ge16GW, A64-OLinuXino-1Ge4GW and A64-OLinuXino-2Ge8G-IND. In
addition, there are two variants without eMMC. One without eMMC and one with SPI
flash. This suggests the need for separate device tree for the three eMMC
variants.
The Linux kernel upstream has chosen to create and use a separate device tree
for the eMMC variants instead of adding eMMC support existing device tree. These
changes to Linux kernel are queued for Linux 5.4.
commit <02bb66b347ff8115f53948f86b884e008ba385b9> ("arm64: dts:
allwinner: a64: Add A64 OlinuXino board (with eMMC)")
This patch has been tested on A64-OLinuXino-1Ge16GW and is based on Linux
device-tree and a64-olinuxino_defconfig.
Signed-off-by: Sunil Mohan Adapa <sunil@medhas.org>
[jagan: updated linux-next commit details]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Half DQ configuration seems to be very rare for H6 based boards/STBs,
but exists nevertheless. Currently the only known product which needs
this support is Tanix TX6 mini.
This commit adds support for half DQ configuration. Code was tested
for regressions on other configurations (OrangePi 3 1 GiB/LPDDR3, Tanix
TX6 4 GiB/DDR3) and none were found.
Thanks to Icenowy Zheng for help with this code.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: thomas graichen <thomas.graichen@gmail.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
SoPine has winbond SPI-FLASH, so enable the same in defconfig
and add aliases for spi0 in -u-boot.dtsi
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
SPI is available in Allwinner A64 SoC, so enable it
globally in Kconfig.
- CONFIG_SPI
- CONFIG_DM_SPI
- CONFIG_DM_SPI_FLASH
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Record two bootstages and add "Starting kernel" message to have standard
handoff message between U-Boot and OS.
Also use debug() instead of #ifdef DEBUG to clean the code.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is no need to show FDT message in regular flow that's why switch it
to debug level.
Fixes: 0905046050 ("microblaze: Switch to generic bootm implementation")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for System Controller available on e-a2197-00 base board.
System is very similar to p-a2197-00 board.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
board_early_init_f added by commit e6cc3b25d7
("arm: zynq: Wire watchdog internals") is no longer needed that's why
remove it also with Kconfig enabling.
Fixes: ccd063e981 ("watchdog: Move watchdog_dev to data section (BSS may not be cleared)")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There are use cases where lpd watchdog can be configured for APU use. By
design this IP should be listed in zynqmp.dtsi to make sure that node is
properly enabled by DTG.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch updates the nand device tree node properties as per
updated driver.
Signed-off-by: Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
ina226 hwmon driver is deprecated and it is recommended to use new iio
based driver. The patch is enabling iio-hwmon driver to export
functionality from IIO to hwmon interface to be able to use lm-sensors
package.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Label property is adding capability to distiguish chips from each other
when iio framework is used.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
ina226 hwmon driver is deprecated and it is recommended to use new iio
based driver. The patch is enabling iio-hwmon driver to export
functionality from IIO to hwmon interface to be able to use lm-sensors
package.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add gpio phy reset via I2C expander TCA6416 on board ZCU102.
A warning call trace is observer in probe when this reset is called
from context that can sleep. Keep this commented until that is
resolved in phylib.
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The DP83867 strap control workaround is already present in Linux kernel
mainline binding. All these Xilinx boards require this quirk.
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
ina226 hwmon driver is deprecated and it is recommended to use new iio
based driver. The patch is enabling iio-hwmon driver to export
functionality from IIO to hwmon interface to be able to use lm-sensors
package.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Label property is adding capability to distiguish chips from each other
when iio framework is used.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
ina226 hwmon driver is deprecated and it is recommended to use new iio
based driver. The patch is enabling iio-hwmon driver to export
functionality from IIO to hwmon interface to be able to use lm-sensors
package.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The si570 clock frequency should be 156.25MHz as per datasheet.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Label property is adding capability to distiguish chips from each other
when iio framework is used.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
ina226 hwmon driver is deprecated and it is recommended to use new iio
based driver. The patch is enabling iio-hwmon driver to export
functionality from IIO to hwmon interface to be able to use lm-sensors
package.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Currently zcu102 Rev1.0 board includes RevA sdhci dt node which has
no-1-8-v property. Since Rev1.0 has level shifters delete this
property to enable support for 1.8v.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Mainline has done this switch and there is no reason not to switch it too.
Mainline U-Boot patch which has done that switch:
"dts: switch spi-flash to jedec, spi-nor compatible"
(sha1: ffd4c7c2ec)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Label property is adding capability to distiguish chips from each other
when iio framework is used.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
ina226 hwmon driver is deprecated and it is recommended to use new iio
based driver. The patch is enabling iio-hwmon driver to export
functionality from IIO to hwmon interface to be able to use lm-sensors
package.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Added tps53679 compatible string to tps53681. They are both compatible to
each other and tps53679 has Linux driver already.
Signed-off-by: Nishant Mittal <nishant.mittal@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Label property is adding capability to distiguish chips from each other
when iio framework is used.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
ina226 hwmon driver is deprecated and it is recommended to use new iio
based driver. The patch is enabling iio-hwmon driver to export
functionality from IIO to hwmon interface to be able to use lm-sensors
package.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Ethernet phys based on devicetree specification should be using
ethernet-phy@ node name instead of pure phy@.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
ZynqMP based System controller is present on Versal boards. This patch is
aligning names with Versal to follow the spec.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
DT binding was reviewed in Linux by commit b0b41af12a1b
("dt-bindings: memory: Add pl353 smc controller devicetree binding
information") that's why this fragment can be also added to U-Boot
repository.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Remove macros which use PM_SIP_SVC offset and convert invoke_smc() to
xilinx_pm_request() which do calculation with PM_SIP_SVC already.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
versal_pm_request() and invoke_smc() are almost the same. Only one
difference is that versal_pm_request is adding PM_SIP_SVC offset to api_id.
The patch is moving platform implementation to firmware driver code for
synchronization.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
As the PHY driver now handles the transitions of USB power domain, we
must add this information in the node of each PHY.
Also, the phy are expected in the "phys" property, not "usb-phys".
Also add the aliases for the USB ports on boards with more than a single
port.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
J721e SoM as a 64MB HyperFlash on board. Add pinmux and DT node for the
same.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Add DT node for HyperBus Memory Controller in the FSS. On J721e, its not
possible to use OSPI0 and HBMC simultaneously as they are muxed within
the Flash Subsystem hence disable HBMC by default as keep OSPI enabled.
Bootloader will fixup DT when it detects HyperFlash instead of OSPI.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Make sure that the clock self-assignment works by having a clock of
clk-sbox be configured automatically when clk-sbox is probed.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Add a few more clocks the clk_sandbox clock provider and get them using
the managed API.
Make sure they are released when the device is removed.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
To allow OCRAM to be used as wakeup source in
deep sleep, do not power it down.
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
The patch adds an errata ID A-008646 for workaround
to provide more information by errata ID.
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
LX2160A/LX2120A/LX2080A SVR value should be
0x873600/0x873620/0x873602
Previous values were valid only if CAN fuse is blown.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
ls1028a has 4 personalities: ls1028a, ls1027a, ls1017a and ls1018a.
Both ls1027a and ls1017a personalities are lower functionality version
which doesn't support the multimedia subsystems, like LCD, GPU.
To disable multimedia feature on non-multimedia version,
set the status property to disabled in dts nodes.
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Program register bit of SCFG_SNPCNFGCR_USBxRDSNP and
SCFG_SNPCNFGCR_USBxWRSNP(x = 1, 2, 3) to drive USBx read/write
snoop signal on LS1043A and LS1046A.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add LS1027A, LS1018A and LS1017A personalities support to
LS1028A SoC family.
LS1028A is the prime personality of LS1028A SoC family.
LS1027A is a lower funtionality version of QorIQ LS1028A
which does not support the multimedia subsystems, such as LCD
controller, GPU, and eDP PHY.
The QorIQ LS1018A and LS1017A SoCs are single 64-bit Arm A72
core, low power versions of the QorIQ LS1028A and LS1027A
SoCs respectively.
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
- add HDMI/CVBS display support for Amlogic G12A SoCs and SEI510 board
- add support for Amlogic A311D based Khadas VIM3
- add support for Amlogic S905X3 based SEI610 board, targeting Android support like SEI510
-----BEGIN PGP SIGNATURE-----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=g/kq
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20191018' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic
- document alternative libretech-cc installation methods, including upstream TF-A and opensource tools
- add HDMI/CVBS display support for Amlogic G12A SoCs and SEI510 board
- add support for Amlogic A311D based Khadas VIM3
- add support for Amlogic S905X3 based SEI610 board, targeting Android support like SEI510
Rename meson-g12a-u-boot.dtsi into meson-g12-common-u-boot.dtsi to
match the new DT architecture and add meson-sm1-sei610-u-boot.dtsi
to handle the U-Boot specific DT for graphics.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Values imported from Linux driver, but in correct numeric order.
Khadas VIM3 prints: Amlogic Meson G12B (A311D) Revision 29:b (10:2)
Cc: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Write SoC instead of Soc. The Linux driver is not affected.
Fixes: f41d723b9f ("ARM: meson: display Amlogic SoC Information")
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
In Linux meson-g12-common.dtsi was introduced as well as new g12b nodes
and headers, as dependencies of new meson-g12b-a311d-khadas-vim3.dts.
Copied from da0c9ea146cb ("Linux 5.4-rc2")
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Like the meson-gx support, add the U-Boot specific bits in DT
to support graphics on G12A SoCs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
If VIDEO_MESON is enabled, we need to setup the fdt for the framebuffer.
Call meson_vpu_rsv_fb() which reserves the framebuffer memory region for
EFI, and sets up simple-framebuffer nodes if simplefb support is
enabled.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
The released Linux boot image header in v5.3 is different from the
one present in U-Boot. Align the header with the new version. The
changes in Linux are backward compatible. Previous U-Boot releases
with older header will continue to work as well. As v5.3 kernel is
the first one to support image header, there is no compatibility
issue between new U-Boot (with this patch) and older kernel.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Rick Chen <rick@andestech.com>
This patch adds a DM based driver model for gpio controller present in
FU540-C000 SoC on HiFive Unleashed A00 board. This SoC has one GPIO
bank and 16 GPIO lines in total, out of which GPIO0 to GPIO9 and
GPIO15 are routed to the J1 header on the board.
This implementation is ported from linux based gpio driver submitted
for review by Wesley W. Terpstra <wesley@sifive.com> and/or Atish Patra
<atish.patra@wdc.com> (many thanks !!). The linux driver can be referred
here [1]
[1]: https://lkml.org/lkml/2018/10/9/1103
Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
- Dropping some test Elf files and building them from source instead
- Refactoring of x86 16-bit entries
- Support for SPL symbols within sections
- Handle the 'notes' sections and hidden symbols in recent binutils
- Improved error reporting with a tool fails
libfdt and documentation fixes
vboot required-key test
driver model power-domain controls
patman Message-Id enhancement
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl2l20YACgkQfxc6PpAI
reZQQQgA0zxySnZR6IuTr+MXJP019SjU0T/rj2Ob77ODhLTtLtE3aFYgBIsyyOyr
/NZ6V7wPhCfGGBGWdPzYdOUIkG5L4O+1zrwWGgVJCAAaCaDlJVIXmljJ667SE9ps
9jfJW/nkzgsa/cOweOUJF3vBUKnDN1pv9aTXwAXttzv/OqaZ1AaUObnmeZ9fzr65
mXjR7/eLYx26KQ8IEo8hhgdFhN/d/aUtSCYPWASqtcI9TLg8A5gmtNxy83+w8gzC
kFIr7c0QjZ3EQHLyD4/MAcGvhZZMBPbV6dyIO19hUS80S1l1yMTd72iTYuvG8bAt
5TzlQCSqvGryF6TRxVn8GPr2/T0v/A==
=Oo/D
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-15oct19' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm
binman enhancements:
- Dropping some test Elf files and building them from source instead
- Refactoring of x86 16-bit entries
- Support for SPL symbols within sections
- Handle the 'notes' sections and hidden symbols in recent binutils
- Improved error reporting with a tool fails
libfdt and documentation fixes
vboot required-key test
driver model power-domain controls
patman Message-Id enhancement
U-Boot cannot be built for h2200_defconfig with CONFIG_DM=y.
The maintainer Lukasz Dalek suggested to remove the board.
https://lists.denx.de/pipermail/u-boot/2019-August/380685.html
Cc: Lukasz Dalek <luk0104@gmail.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
[trini: As this is the last non-toradex PXA board, update travis too]
Signed-off-by: Tom Rini <trini@konsulko.com>
Without this patch, compiling may potentially fail.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
When I tried to run some new efi tests with pytest, efi_smbios_register()
triggered a segmentation fault. Here is the location where it happened:
efi_init_obj_list()
efi_smbios_register()
write_smbios_table()
smbios_write_type4()
smbios_write_type4_dm()
where dev_get_parent_platdata() should return a pointer to struct
cpu_platdata, but it is actually NULL because any cpu device on
sandbox is attached to "root_driver."
With this patch, this issue will be fixed by moving all the definitions
of cpus under "cpus" node so that they have a "cpu_bus" parent.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present these two sections of code are linked together into a single
2KB chunk in a single file. Some Intel SoCs like to have a FIT (Firmware
Interface Table) in the ROM and the pointer for this needs to go at
0xffffffc0 which is in the middle of these two sections.
Make use of the new 'reset' entry and change the existing 16-bit entry to
include just the 16-bit data.
Signed-off-by: Simon Glass <sjg@chromium.org>
-------------------
Travis: https://travis-ci.org/sbabic/u-boot-imx/builds/597498628
- logicpd pinmux
- i.MX7ULP: imx_ddr_size
- fixes Toradex i.MX6/i.MX7
- pico-imx7d
- tpc70 converted to DM
- New Board: meerkat96
- add HAB version command
- i.MX8 :
imx8: Jump from alias to OCRAM address at SPL init
imx8qm/qxp: Set SPL TEXT base to OCRAM base
-----BEGIN PGP SIGNATURE-----
iQHDBAABCgAtFiEEiZClFGvhzbUNsmAvKMTY0yrV63cFAl2kbrYPHHNiYWJpY0Bk
ZW54LmRlAAoJECjE2NMq1et30iQL/RDCe3R1MuQPQdjBEUcb+ZXP8/vaAAbgAsv6
MNN/ybJ8pIXGVF5qxJxzZgMcUvIq1vy8romomIwVBOr7gueoYMokpKeE95P4XK2r
HmFM+/ZcXIXvDrHrULDquAvCG6zhOMHXdbmWcQcZLcHSCsZpkh4YuuGzFVpxTgNE
kTJpEF+Orw49w9wMVKeqfv9z3MsYkr/vV3kH/+ISndN6cOBOjV56Qzl/hlzxiN1d
wueTQi1pxUVjbsKWIkf76XTeSa5621bM01+YMN3CFq/AWhVMbpnaWWGB6ET4NBjD
k/BjRgCZ+/hwjpHnbylHEmsLolNsIXn8KirE73OCmIvov/vUYaaZJ5lBzU+L2A5k
tK6p1LOTvsRxKBsN49hQIQLJMcn/sp9RpP9ohgCs3lj7bKGAQ1HoxqylypeDGPv1
htKGdBFGiEfoCus1Ob7NAevYAPlVM7h+mDzFSYhlr9BZnrDj2V3nwICj8KV3wkwl
lPiUQiYMUhgvSSSiU2NJDSy1onjSXA==
=J8jd
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20191014' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
u-boot-imx-20191014
-------------------
Travis: https://travis-ci.org/sbabic/u-boot-imx/builds/597498628
- logicpd pinmux
- i.MX7ULP: imx_ddr_size
- fixes Toradex i.MX6/i.MX7
- pico-imx7d
- tpc70 converted to DM
- New Board: meerkat96
- add HAB version command
- i.MX8 :
imx8: Jump from alias to OCRAM address at SPL init
imx8qm/qxp: Set SPL TEXT base to OCRAM base
- Add sdhci driver for Broadcom iProc platform
- Add a driver callback for power-cycle for mmc
- Implement host_power_cycle callback for stm32_sdmmc2
- spl: dm_mmc: Initialize only the required mmc device
THe RVT data includes a major and minor version in its header
parameter. Add a new command to print this out.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
i.MX7ULP uses the same MMDC controller IP as found on i.MX53
and i.MX6, so build mmdc_size.c for i.MX7ULP as well.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
The original imx_ddr_size() implementation had some
issues reported by checkpatch like this:
CHECK: Prefer kernel type 'u32' over 'uint32_t'
#127: FILE: arch/arm/mach-imx/mmdc_size.c:16:
+ uint32_t ctl;
WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
#151: FILE: arch/arm/mach-imx/mmdc_size.c:40:
+ unsigned ctl = readl(&mem->ctl);
Fix all of them.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Place imx_ddr_size() into a separate file.
The motivation for doing this is to be able to easily reuse
imx_ddr_size() on i.MX7ULP.
Currently imx_ddr_size() is inside arch/arm/mach-imx/cpu.c, which
is not built for i.MX7ULP.
Changing the logic to allow building cpu.c for i.MX7UP would
require adding several ifdef's, leading to a not a very elegant
solution.
To allow better reuse, just place imx_ddr_size() into a common
mmdc_size.c file.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Stefano Babic <sbabic@denx.de>
The new class dsi host allows the management of the bridge DPI to DSI.
This bridge is embedded in the chipset mp1 (come from synopsys company).
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
The new class dsi host allows the management of the bridge DPI to DSI.
This bridge is embedded in the chipset mp1 (come from synopsys company).
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
Display Serial Interface (DSI) host can usefully be modelled
as their own uclass.
DSI defines a serial bus and a communication protocol
between the host and the device (panel, bridge).
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
When running SPL on iMX8, the A core starts at address 0
which is a alias to OCRAM 0x100000.
The alias only map first 96KB of OCRAM, so this require the
SPL size can't beyond 96KB. But when using SPL DM, the size increase
significantly and may exceed 96KB.
So to fix the problem, we will change SPL linker address to OCRAM
address 0x100000. And then jump to the absolute address not the PC relative
address for entering OCRAM.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
This patch converts the TPC70 to use driver model and device tree
description in both SPL and u-boot proper.
Notable changes (DM/DTS conversion):
- PINCTRL{_IMX6}
- DM_I2C
- enable 'regulator' and 'pmic' commands
- DM_MMC and BLK (USDHC)
- DM_ETH
- DM WDT (including SYSRESET)
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This commit adds new file - imx6q-kp-u-boot.dtsi with a set of u-boot
specific properties for imx6q KP device.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
With the 256KB of OCRAM available to SPL now, there should be
enough room to enable the pinmuxing in SPL from the device tree.
This patch enables SPL_PINCTRL et al and adds the serial and
usdhc pin mux references to the -u-boot.dtsi file so the pins can be
configured from the device tree.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The Meerkat96 board, based on the NXP i.MX7D SoC, is a member of
96Boards community and complies with all Consumer Edition board
specifications.
https://www.novtech.com/products/meerkat96.htmlhttps://www.96boards.org/product/imx7-96/
The initial supported/tested devices include:
- Debug serial
- SD
- USB Host (with Ethernet)
With these support, it's good enough for loading Linux Kernel from SD or
Ethernet over USB.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
If an exception occurs in a loaded image and the relocation offset is
unknown, it is helpful to know the instructions pointed to by the
program counter. This patch adds the missing output.
A possible output is:
Code: 910c4021 aa1303e0 f9400662 d63f0040 (e7f7defb)
The parentheses indicate the instruction causing the exception.
The output can be disassembled using scripts/decodecode:
echo 'Code: 90000360 9100b800 94002782 17ffff8f (e7f7defb)' | \
ARCH=arm64 scripts/decodecode
Code: 90000360 9100b800 94002782 17ffff8f (e7f7defb)
All code
========
0: 90000360 adrp x0, 0x6c000
4: 9100b800 add x0, x0, #0x2e
8: 94002782 bl 0x9e10
c: 17ffff8f b 0xfffffffffffffe48
10:* e7f7defb .inst 0xe7f7defb ; undefined <-- trapping instruction
Code starting with the faulting instruction
===========================================
0: e7f7defb .inst 0xe7f7defb ; undefined
We already have implemented the same for armv7.
For testing command 'exception undefined' can be used.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
readb is unconditionally defined earlier in io.h, so there's no point
checking whether it's undefined.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
No ARM board seems to define __mem_pci - and if it did, one would get tons of
./arch/arm/include/asm/io.h:307:0: warning: "readl" redefined
warnings, because readl and friends are unconditionally defined
earlier in io.h. Moreover, the redefinitions lack the memory barriers
that the first definitions have. So I'm guessing this is practically
dead code.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
If there is any failure during IOdelay recalibration sequence, IOs are
not guaranteed to behave as expected. So hang on any failure during the
sequence.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
When an error is reported in __recalibrate_iodelay_start(), de-isolation
of IO doesn't happen. Because of this, undefined behaviour is observed
on many peripherals without any error. So make sure io is out of isolation
at the end of iodelay recalibration.
Reported-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Main uart0 is used as debug console by both R5SPL and A72 bootloader and
Linux. So mark it as shared device so that power-domain request is
successful by both cores.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
AM335x-ICE boards contain the CDCE913 clock synthesizer, and their
reset crystal capacitance load value of 10pF is wrong leading into
lost packets in certain networking tests. Add DT data for this
device, and probe it from the board file to program the crystal
capacitance load value to 0pF to avoid any problems.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
AM43xx-IDK boards contain the CDCE913 clock synthesizer, and their
reset crystal capacitance load value of 10pF is wrong leading into
lost packets in certain networking tests. Add DT data for this
device, and probe it from the board file to program the crystal
capacitance load value to 0pF to avoid any problems.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
AM57xx-IDK boards contain the CDCE913 clock synthesizer, and their
reset crystal capacitance load value of 10pF is wrong leading into
lost packets in certain networking tests. Add DT data for this
device, and probe it from the board file to program the crystal
capacitance load value to 0pF to avoid any problems.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
- add BOARD_LATE_INIT function calls in board.c
- add swi_status detection in board.c
- mux: add guardian interfaces to single pinmux structure
- am33xx, kconfig: add BOARD_LATE_INIT for GUARDIAN board
Signed-off-by: Moses Christopher <BollavarapuMoses.Christopher@in.bosch.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Before the priming begins, we need to disable RMW (Read Modify Write)
and disable ECC verification for read accesses. By default, the EMIF
tool enables RMW and read accesses in the EMIF_ECC_CTRL_REG.
Signed-off-by: Krunal Bhargav <k-bhargav@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
If ECC is enabled, we need to ensure interleaving is disabled for higher
address space.
Signed-off-by: Krunal Bhargav <k-bhargav@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
ecc_address_range registers contains the start address and end address
of the DDR address space. But the ddr driver is assuming the register
contains the start address and size of the DDR address space. Because
of this the ecc enabling is failing for the 2nd range of ecc addresses.
Fix this calculation.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
This follows the linux header rules to avoid conflict bitfields.
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
This adds PCIe and its PHY nodes for MT7623.
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
This commit add a spi-nor device in the bcm96850xref device tree.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Kursad Oney <kursad.oney@broadcom.com>
This commit add a hsspi controller in the bcm6858 device tree.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Kursad Oney <kursad.oney@broadcom.com>
This change adds a spi nor flash device to the bcm963158 board.
Signed-off-by: Kursad Oney <kursad.oney@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
This change adds the hsspi controller to the 63158 dtsi.
Signed-off-by: Kursad Oney <kursad.oney@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
The A72 U-Boot code loads and boots a number of remote processors
including the C71x DSP, both the C66_0 and C66_1 DSPs, and the various
Main R5FSS Cores. In order to view the code loaded by the U-Boot by
remote cores, U-Boot should configure the memory region with right
memory attributes. Right now U-Boot carves out a memory region which
is not sufficient for all the images to be loaded. So, increase this
carve out region by 256MB.
Signed-off-by: Kedar Chitnis <kedarc@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The A53 U-Boot code can load and boot the MCU domain R5F cores (either a
single core in LockStep mode or 2 cores in Split mode) to achieve various
early system functionalities. Change the memory attributes for the DDR
regions used by the remote processors so that the cores can see and
execute the proper code loaded by U-Boot.
These regions are currently limited to 0xa0000000 to 0xa2100000 as per
the DDR carveouts assigned for these R5F cores in the overall DDR memory
map.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The AM65x SoCs has a single dual-core Arm Cortex-R5F processor
subsystem/cluster (MCU_R5FSS0) within the MCU domain. This cluster
can be configured at boot time to be either run in a LockStep mode
or in an Asymmetric Multi Processing (AMP) fashion in Split-mode.
This subsystem has 64 KB each Tightly-Coupled Memory (TCM) internal
memories for each core split between two banks - ATCM and BTCM
(further interleaved into two banks). There are some IP integration
differences from standard Arm R5 clusters such as the absence of
an ACP port, presence of an additional TI-specific Region Address
Translater (RAT) module for translating 32-bit CPU addresses into
larger system bus addresses etc.
Add the DT node for the MCU domain R5F cluster/subsystem, the two
R5 cores are added as child nodes to the main cluster/subsystem node.
The cluster is configured to run in Split-mode by default, with the
ATCMs enabled to allow the R5 cores to execute code from DDR with
boot-strapping code from ATCM. The inter-processor communication
between the main A72 cores and these processors is achieved through
shared memory and Mailboxes.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The J721E SoCs have a single TMS320C71x DSP Subsystem in the MAIN
voltage domain containing the next-generation C711 CPU core. The
subsystem has 32 KB of L1D configurable SRAM/Cache and 512 KB of
L2 configurable SRAM/Cache. This subsystem has a CMMU but is not
used currently. The inter-processor communication between the main
A72 cores and the C711 processor is achieved through shared memory
and a Mailbox. Add the DT node for this DSP processor sub-system
in the common k3-j721e-main.dtsi file.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The J721E SoCs have two TMS320C66x DSP Core Subsystems (C66x CorePacs)
in the MAIN voltage domain, each with a C66x Fixed/Floating-Point DSP
Core, and 32 KB of L1P & L1D configurable SRAMs/Cache and an additional
288 KB of L2 configurable SRAM/Cache. These subsystems do not have
an MMU but contain a Region Address Translator (RAT) sub-module for
translating 32-bit processor addresses into larger bus addresses.
The inter-processor communication between the main A72 cores and
these processors is achieved through shared memory and Mailboxes.
Add the DT nodes for these DSP processor sub-systems in the common
k3-j721e-main.dtsi file.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The J721E SoCs have 3 dual-core Arm Cortex-R5F processor (R5FSS)
subsystems/clusters. One R5F cluster (MCU_R5FSS0) is present within
the MCU domain, and the remaining two clusters are present in the
MAIN domain (MAIN_R5FSS0 & MAIN_R5FSS1). Each of these can be
configured at boot time to be either run in a LockStep mode or in
an Asymmetric Multi Processing (AMP) fashion in Split-mode. These
subsystems have 64 KB each Tightly-Coupled Memory (TCM) internal
memories for each core split between two banks - ATCM and BTCM
(further interleaved into two banks). There are some IP integration
differences from standard Arm R5 clusters such as the absence of
an ACP port, presence of an additional TI-specific Region Address
Translater (RAT) module for translating 32-bit CPU addresses into
larger system bus addresses etc.
Add the DT nodes for these two MAIN domain R5F cluster/subsystems,
the two R5 cores are each added as child nodes to the corresponding
main cluster node. Configure SS0 in split mode an SS1 in lockstep mode,
with the ATCMs enabled to allow the R5 cores to execute code from DDR
with boot-strapping code from ATCM.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The J721E SoCs have 3 dual-core Arm Cortex-R5F processor (R5FSS)
subsystems/clusters. One R5F cluster (MCU_R5FSS0) is present within
the MCU domain, and the remaining two clusters are present in the
MAIN domain (MAIN_R5FSS0 & MAIN_R5FSS1). Each of these can be
configured at boot time to be either run in a LockStep mode or in
an Asymmetric Multi Processing (AMP) fashion in Split-mode. These
subsystems have 64 KB each Tightly-Coupled Memory (TCM) internal
memories for each core split between two banks - ATCM and BTCM
(further interleaved into two banks). There are some IP integration
differences from standard Arm R5 clusters such as the absence of
an ACP port, presence of an additional TI-specific Region Address
Translater (RAT) module for translating 32-bit CPU addresses into
larger system bus addresses etc.
Add the DT node for the MCU domain R5F cluster/subsystem, the two
R5 cores are added as child nodes to the main cluster/subsystem node.
The cluster is configured to run in LockStep mode by default, with the
ATCMs enabled to allow the R5 cores to execute code from DDR with
boot-strapping code from ATCM. The inter-processor communication
between the main A72 cores and these processors is achieved through
shared memory and Mailboxes.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Although we currently use the MAIN_UART0 for R5 SPL console output there
are cases where we require access to the MCU_UART0 as well for example in
case of UART-based Y-Modem boot. To support these scenarios add related
DTS definitions to be able to use that UART early on.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
In order to allow booting TI K3 family SoCs via Y-Modem add support for
loading System Firmware by tapping into the associated SPL core loader
function.
In this context also make sure a console is available and if not go
ahead and activate the early console feature which allows bringing up
an alternate full console before the main console is activated. Such
an alternate console is typically setup in a way that the associated
UART can be fully initialized prior to SYSFW services being available.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Implement an early console functionality in SPL that can be used before
the main console is being brought up. This helps in situations where the
main console is dependent on System Firmware (SYSFW) being up and running,
which is usually not the case during the very early stages of boot. Using
this early console functionality will allow for an alternate serial port
to be used to support things like UART-based boot and early diagnostic
messages until the main console is ready to get activated.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
At present this produces a 16-byte file. It is intended to start 16 bytes
before the end of ROM and pads with zeroes to readh the end.
But binman sometimes wants to add an image-header at the very end of ROM.
Furthermore binman automatically pads the data if it is finishes early.
Drop the padding in resetvec and let binman handle it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
This is not used anywhere now, so drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Since x86 users binman now, we don't need this compile-time define.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Many of the Kconfig options do not apply to FSP2. Update them to use the
FSP_VERSION1 condition instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Move the code to determine the size of a cache record into a function so
we can use it elsewhere in this file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present when these fail to boot there is no message, just a hang. Add a
panic so it is obvious that something when wrong.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Pick minor changes from the downstream DT, disable MMC, add GMAC0 node
and adjust PHY skew settings for GMAC1.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
The company Samtec was merged into Softing, migrate the board over to
the new name and update copyright headers.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
- Rename existing FSP code to fsp1
- Add fsp2 directory in preparation to support FSP 2.0
- Various x86 platform codes update
- Various bug fixes and updates in dm core, sandbox and spl
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdnCy/AAoJEB6zHgIOrC/Izp4IAJVDE0oyOYcwBoCsAqa8zvMJ
/G815T1TGyc6674TQ+Px47t+1O9InClag576E1ttKVSZHnTqH9AW1aGdVqYFgmwu
bbk7a/N2bSYc1ZruiH1YMzwVMTmwaIvn9cvNeBMkQ0cXBP6R7m9DsupaTG9mNsll
7wNFF6gZCOXQEOL6hgxerxr6UM2xaQMpSqfYhfYfmHyU0S86Cr1J7dORL1MHhZ4/
WLVuxCPpgeTwiZ0i9TerC0eH0agPQ2dmtDPAQFn+RihVS29YNDTaR+a4XVKJJ6hs
Y/77d0JYmPSY5JgYLAdjqx+GQKKqy9kpdHJz+sXCiolDdYHmG3c+4zQzrLzkH+k=
=Y0qG
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2020.01-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
First set of u-boot-atmel features and fixes for 2020.01 cycle
The feature set includes support for two new boards from Microchip AT91:
The sama5d27_wlsom1_ek , an evaluation kit which includes the SAMA5D2
SOC packaged in a 256 MB LPDDR2 SIP, on a SOM including wireless, which
is placed on evaluation kit with sd-card, ethernet, LCD, Camera sensor,
QSPI, etc
The sam9x60ek, an evaluation kit for the new SoC based on ARM926j , the
SAM9X60 . The evaluation kit includes NAND flash, QSPI, Ethernet, Audio,
Camera sensor connector, etc.
The full support for sam9x60ek will come at a later time. There are
still missing bits regarding the clock support and power management
controller.
The major corrections in this pull request are:
Fixes for the SetVariable() boot service.
Device path node for NVMe drives.
Disable CONFIG_CMD_NVEDIT by default.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEbcT5xx8ppvoGt20zxIHbvCwFGsQFAl2aVscACgkQxIHbvCwF
GsTx+Q//ThJM6BGFE3Rk2pI0SXGqyPK1CIt78S8xj9WFjowpnL4y3sU5NQryzf7k
OdGvl4KnO+qNHVIaUuOU+ylCms/DdJZcqljBE+VGRiHijjeWuWb4zv70655/DQra
zxBXhmGM1RoabTR6ZosXDx9QRz+qg7eVP66oFHXAPjiAj0UEYiiKTO4wCV882POa
thqI/mEg7wFI9abyVbvpG36ROT/h0t5uvH0B7h/rsCMOK9ABHrWOcy6/xibu0gZT
Y25/ve6fxGfd8vW1b4/z/F+hPXqy+LYbblm+hZ+mCDPZ0kblmqmbeXGydDZkr2UN
pm6niczwWqb5PL1Z5KevfytbojQTN6vnedIw3yUEFA6Znh2uSW4pry1xMQbpfkuw
EQc0r0eoxlMyc0PCYqKoznrje0GXBaEG71+wcG5hhWQCzdx3BktUosrLdAdj4Km+
nho+WxOSXv3rPntY9etQ6U+EyyOyDXMHud2tnE3BN0L+gIl7pLyf3TCS/NumTAFm
R7Gf9/YjazExmdJrpEjq+rBVHoF7+wdfBzok6aEw1BmTqqNiBEGpkywgg7eHYjIG
lThM4VE14VITGq95FbnkhmH33NDD89UQ4DRbPWC10IajSZbGktUpIRYdYQKKHGDq
vRWaaF61eDOIY4xQlX3ecDlsi5rKF2EdBtqAxWekZAAMA64okcw=
=nzgb
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-01-rc1' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-01-rc1
The major corrections in this pull request are:
Fixes for the SetVariable() boot service.
Device path node for NVMe drives.
Disable CONFIG_CMD_NVEDIT by default.
Apologies to everyone whose board I broke by attempting to return
MMC1 or MMC2. I misunderstood how the MMC indexing worked.
This reverts commit 14d319b185.
Signed-off-by: Adam Ford <aford173@gmail.com>
Since convert dm_video, unused code introduced, so remove this
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Reviewed-by: Otavio Salvador <otavio@ossystems.com.br>
CONFIG_SECURE_BOOT is too generic and forbids to use it for cross
architecture purposes. If Secure Boot is required for imx, this means to
enable and use the HAB processor in the soc.
Signed-off-by: Stefano Babic <sbabic@denx.de>
To avoid hardcoded offset when adding u-boot.cnt to flash.bin, we use
flexible offset which is calculated based on the size of the container
image generated int the first stage. And pad u-boot.cnt at 1KB
alignment.
So add code to get the offset when SPL loading u-boot.cnt.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Import i.MX8MM pin func from Linux Kernel,
commit <0a8ad0ffa4d8> ("Merge tag 'for-linus-5.3-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Import i.MX8MM dtsi from Linux Kernel,
commit <0a8ad0ffa4d8> ("Merge tag 'for-linus-5.3-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Because we need to get cpu freq in print_cpuinfo at very early stage,
so we need to make sure the ccm be probed.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When DM_MMC enabled, the USDHC index in U-Boot is the USDHC port.
To directly return devno, we could avoid add board specific code.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Introduce clk implementation for i.MX8MM, including pll configuration,
ccm configuration. Mostly will be done clk dm driver,
but such as DRAM part, we still use non clk dm driver, because we
have limited sram.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
i.MX8MQ and i.MX8MM use different analog pll design, but they
share same ccm design.
Add clock_imx8mq.h for i.MX8MQ
keep common part in clock.h
Signed-off-by: Peng Fan <peng.fan@nxp.com>
To i.MX8MM SCTR clock is disabled by ROM, so before timer init
need to enable it.
To i.MX8MQ, it does not hurt the clock is enabled again.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Set trustzone region 0 to allow both non-secure and secure access
when trust zone is enabled. We found USB controller fails to access
DDR if the default region 0 is secure access only.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
set the BYPASS ID SWAP bit (GPR10 bit 1) in order for GPU not to
generated AXI bus errors with TZC380 enabled.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When running with OPTEE, the MMU table in u-boot does not remove the OPTEE
memory from its settings. So ARM speculative prefetch in u-boot may access
that OPTEE memory. Due to trust zone is enabled by OPTEE and that memory
is set to secure access, then the speculative prefetch will fail and cause
various memory issue in u-boot.
The fail address register and int_status register in trustzone has logged
that speculative access from u-boot.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
i.MX8MM has similar architecture with i.MX8MQ, but it has totally
different PLL design and register layout change.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
There is no HDMI on i.MX8MM, so we need to remove HDMI entry, then
we could not reuse imximage.cfg, so create a new one.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Fix the FIT image metadata for i.MX8 to result in the intended boot
order (SPL -> ATF -> U-Boot).
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Similar to "spl_sd.cfg", this patch introduces "spl_qspi.cfg" so that
all i.MX6 based boards can use it, when they use SPL and QSPI boot
mode.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
This patch adds the missing boot mode detection for QSPI boot on
i.MX6UL/ULL. Without it, booting with SPL from QSPI NOR does not work.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
The default CSF_SIZE defined in Kconfig is too high and SPL cannot
fit into the OCRAM in certain cases.
The CSF cannot achieve 0x2000 length when using RSA 4K key which is
the largest key size supported by HABv4.
According to AN12056 "Encrypted Boot on HABv4 and CAAM Enabled Devices"
it's recommended to pad CSF binary to 0x2000 and append DEK blob to
deploy encrypted boot images.
As the maximum DEK blob size is 0x58 we can reduce CSF_SIZE to 0x2060
which should cover both CSF and DEK blob length.
Update default_image.c and image.c to align with this change and avoid
a U-Boot proper authentication failure in HAB closed devices:
Authenticate image from DDR location 0x877fffc0...
bad magic magic=0x32 length=0x6131 version=0x38
bad length magic=0x32 length=0x6131 version=0x38
bad version magic=0x32 length=0x6131 version=0x38
spl: ERROR: image authentication fail
Fixes: 96d27fb218 (Revert "habv4: tools: Avoid hardcoded CSF size for SPL targets")
Reported-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Add support for the power domain controller that's used on the
i.MX8MQ. This will be needed to be able to power on the PCIe
controller. Bindings taken from Linux, driver implementation
taken from the i.MX8 power domain controller and adjusted for
the i.MX8M SoC.
Signed-off-by: Patrick Wildt <patrick@blueri.se>
After this change it is possible to use imx28-<board>-u-boot.dtsi with
the imx28-u-boot.dtsi explicitly included without breaking setup from
imx28-<board>.dts file.
The problem is that the imx28.dtsi included in a wrong place overrides the
changes made in imx28-<board>.dts. As a result some devices are "disabled"
in the final DTB.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This change tries to fix the following problem:
- The board boots (to be more precise - ROM loads SPL) from a slow SPI-NOR
memory.
As a result the spl_boot_device() will return SPI-NOR as a boot device
(which is correct).
- The problem is that in 'falcon boot' the eMMC is used as a boot medium to
load kernel from its partition.
Calling spl_boot_device() will break things as it returns SPI-NOR device.
To fix this issue the new CONFIG_SPL_FORCE_MMC_BOOT Kconfig flag is
introduced to handle this special use case. By default it is not defined,
so there is no change in the legacy code flow.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This commit enables support for CONFIG_WDT in the U-Boot proper. Moreover,
the SYSRESET_WATCHDOG driver is used to support 'reset' command.
As SPL is not yet ready for DM conversion, the CONFIG_HW_WATCHDOG is
enabled for it. This allows the legacy SPL code to work properly.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The DM/DTS support for SPI is disabled on purpose for SPL, as it is not
supported as of time of this conversion.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
After this commit the display5 device would use I2C driver supporting
driver model (DM_I2C).
The 'i2c' and 'eeprom' commands now use DM I2C drivers and initialize
on-bus devices according to device tree description.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Add the initial support for the pico-imx6 variants.
DDR initialization is based on the TechNexion's U-Boot code.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Allow enable_ipu_clock() to be built for SPL code. This is done
in preparation for configuring the NoC registers on i.MX6QP in SPL.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Add sc_pm_is_partition_started to check whether a partition
has been started. This will be used to detect M4 partition booted up or
not, then we could choose which dtb to use. If M4 is up, we need
use dtb, such as imx8qm-mek-rpmsg.dtb.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add OP-TEE device tree node for Linux according to args passed from ATF.
If ATF has been built with OP-TEE running, boot_pointer[1] will indicate
that.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
On i.MX8QM, sid is programmable, so we could program sid according the
value encoded in device tree.
This patch support legacy bindings which are still being used by XEN
and new bindings used by Linux Kernel.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When resource is not assigned to non-secure Linux, if linux continue
to use the node, linux may crash or hang. So need to set the node
status to disabled for not owned resources.
The resource id is in the power-domains property in device tree,
so parse the power-domains property to get the resource id and
use scfw api to check whether it is owned by current partition.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Since SCU MU driver has been bound in dm_init, so we don't need to
bind it again. Just replace by using uclass function to probe it.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
To support SPL loading container file, add a new Makefile target,
and introduce a new Kconfig file to source the cfg file which
will be parsed by mkimage.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add parsing i.MX8 Container file support, this is to let
SPL could load images in a container file to destination address.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The changes were added by following patch:
commit <9002e735e717> ("imx: mx6sabresd: fix boot hang with video")
commit <f45ec8fcfb86> ("imx6: dts: add 'u-boot, dm-pre-reloc' to soc and ipu nodes")
Let's move the U-Boot specific change to imx6qdl-u-boot.dtsi
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Move CONFIG_CSF_SIZE to Kconfig and define default value as 0x4000.
mx8mqevk requires 0x2000 add this configuration in imx8mq_evk_defconfig
file.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
On i.MX7ULP B0, there is change in NIC clock dividers architecture.
On A0, the NIC1 BUS and EXT dividers were in a chain with NIC1 DIV, but
on B0 they are parallel with NIC1 DIV. So now the dividers are independent.
This patch modifies the scg_nic_get_rate function according to this change.
Signed-off-by: Ye Li <ye.li@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
The normal target frequency for ULP A7 core is 500Mhz, but now ROM
set the core frequency to 413Mhz. So change it to 500Mhz in u-boot.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The GPU uses APLL PFD2 as its clock parent (483.84Mhz) with divider
set to 1. This frequecy is out of ULP A0 spec. The MAX rate for GPU
is 350Mhz. So we simply configure the APLL PFD2 to 345.6Mhz (FRAC=28)
to workaround the problem. The correct fix should let GPU handle the
clock rate in kernel.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The num/denom is a float value, but in the calculation it is convert
to integer 0, and cause the result wrong.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Wrong I2c driver configuration name is used in codes, so I2c driver is
not built. Correct it.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Since many drivers need this CONFIG_MX7ULP to distiguish the settings
for i.MX7ULP only. Add this entry to cpu's kconfig.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The offset for FRAC and the mask for PCD are not correct.
If we set FRAC, we can't get the right frequency. Fix them
to correct value.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
On i.MX7ULP, value zero is reserved in SCG1 RCCR register,
so the val should be decreased by 1 to get the correct clock
source index.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The board will reboot if A7 core enter mem mode by rtc, then M4 core
enter VLLS mode after the RTC alarm expired. Enable the dumb PMIC mode
to fix this issue.
Since i.MX7ULP B0 moves the SNVS LP into M4 domain, A core can't access
it. So check the CPU rev and not apply the settings for B0.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Previously the SPL size on all iMX6 platforms was restricted to 68KB
because the OCRAM size on iMX6SL/DL parts is only 128KB. However, the
other iMX6 variants have 256KB of OCRAM. Add an option
CONFIG_MX6_OCRAM_256KB which allows using the full size on boards which
don't need to support the SL/DL variants. This allows for an SPL size of
196KB, which makes it much easier to use configurations such as SPL with
driver model and FDT control.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Tested-by: Adam Ford <aford173@gmail.com> #imx6q_logic
There is no need to use HAB for FIT signature validation when
SPL_FIT_SIGNATURE is also enabled, as that will be validated via the
normal U-Boot signed FIT image flow.
This allows having SPL validated by HAB and the payloads to follow
being validated with FIT signatures only.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Toradex Apalis iMX6 modules are available in the iMX6D and iMX6Q
variants, which are quite similar and already managed via only one
dtb in u-boot (imx6-apalis.dtb). Select MX6Q via Kconfig by default in
order to automatically enable the HAS_CAAM and MX6_SMP features.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
The gpio command currently uses equal bank names "GPIO0_"
for all existing gpio banks, i. e.:
U-Boot# gpio status -a
Bank GPIO0_:
GPIO0_0: input: 0 [ ]
GPIO0_1: input: 0 [ ]
...
Bank GPIO0_:
GPIO0_0: input: 0 [ ]
GPIO0_1: input: 0 [ ]
...
So the command is broken, it is not possible to address
a desired bank. Add gpio aliases to fix this.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Pass spl_image and bootdev to board_return_bootrom.
i.MX8MN needs the args to let ROM to load images
Cc: Simon Glass <sjg@chromium.org>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
To support DM_VIDEO,
Add display node for lcdif
Drop board iomuxc settings.
Enable DM_VIDEO
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Add i.MX6ULZ board support. the i.MX6ULZ is SW compatible
with i.MX6ULL. so most code of i.MX6ULL can be reused
by i.MX6ULZ.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add i.MX6ULZ cpu type and helper.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Import kernel dts for i.MX6ULZ from
commit <0a8ad0ffa4d8> ("Merge tag 'for-linus-5.3-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Sync kernel dts for i.MX6ULL from
commit <0a8ad0ffa4d8> ("Merge tag 'for-linus-5.3-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Sync kernel dts for i.MX6UL from
commit <0a8ad0ffa4d8> ("Merge tag 'for-linus-5.3-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Move the exisiting function of getting board dtb from versal to a common
Xilinx folder.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
With new mailbox driver PMUFW configuration object can be loaded via the
same interface and there is no need to have pmu_ipc.c completely.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Probe ZynqMP firmware driver on the board initialization phase and
ensure that firmware is in place to continue execution. The probing is
done on board_init so it can be used for both SPL and U-Boot proper.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Removes the old function to get the firmware version.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
New firmware header to place firmware specific macro and function
declarations. The patch also moves the macros defining PM operations as
well as some helper macros.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Cleanup PM ID handling by using enum values.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The following patch adds a mailbox node and firmware node to following the
mainline DT.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
zynqmp-power driver for ZynqMP to handle the communication with the PMU
firmware. Firmware driver just probes subnodes and power driver handles
communication with PMU using the IPI mailbox driver.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
ZynqMP mailbox driver implementing IPI communication with PMU. This would
allow U-Boot SPL to communicate with PMUFW to request privileged
operations.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Setup initrd_high and fdt_high to be placed in lowmem space for kernel to
be able to reach it. Values are setup at run time to ensure that the same
setting can be used on different memory setup. Do this setting only when
variables are not
Similar run time detection was done for Zynqmp and Versal.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is no reason to use private code for standard bootm command.
Current implementation is also broken and don't support image relocation
properly. Switching to generic bootm implementation is fixing these issues.
cmdline and bdt bootm subcommands are returning -1 because they are not
implemented.
Similar change was done long time ago by for example commit 2bb5b63879
("MIPS: bootm: rework and fix broken bootm code")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
arch_lmb_reserve() protects U-Boot relocated code with stack not to be used
for image relocation.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Similar SCs but different wiring.
- dc_i2c is connected to X-PRC cards that's why label is required to have
an option to hook up some devices.
- Exactly identify i2c devices on x-prc boards.
In case of missing i2c connection devices won't be accessible.
- USB 0 should be device mode with super speed.
- USB 1 should be host mode.
- Fix i2c mux reset pin entry - commented, not verified.
- Fix i2c1 eeprom compatible string - it is an ST 128Kbit device.
Need to use atmel fallback.
- Fix si570 I2C slave address and add corresponding part numbers.
- Enable AMS for system monitoring.
- phy reset property should be commented because it will throw a
warning dump when called from context that can sleep.
No support for phys property (zynqmp phy driver) with SGMII.
Add is-internal-pcspma property required by uboot.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Change has been done across the whole tree only zynqmp-mini-qspi hasn't
been fixed.
Origin changed done by commit ffd4c7c2ec
("dts: switch spi-flash to jedec, spi-nor compatible")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch added alias for usb node in dts file.
Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds clock driver support for Versal platform. The clock driver
queries and performs clock operations using PLM firmware by communicating
with it using SMC calls.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch provides an option to enable/disable OCM and TCM memory into MMU
table with corresponding memory attributes.
The same change was done for ZynqMP by commit 189bec47ab
("arm64: zynqmp: Provide a Kconfig option to define OCM and TCM in MMU")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Code reads DT and setup MMU table based on memory node. This will ensure
that only DT needs to be changed.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch is setting up the initrd_high to as high as possible by leaving
max stack size for u-boot so that bigger rootfs can also be loaded by
u-boot for booting kernel.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch is setting up the initrd_high to as high as possible by leaving
max stack size for u-boot so that bigger rootfs can also be loaded by
u-boot for booting kernel.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Define board_late_init which performs bootmode detection
and prepares corresponding distro boot commaand sequence.
Also disable it for mini platforms because simply there is no need to have
it enabled.
But also disable it for virtual platform because Qemu is not modelling this
register space that's why travis testing would fail. This configuration
should be reverted when mainline Qemu is updated.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This node is used by qspi driver for supporting qspi boot mode in SPL.
Similar changes have beeen done by commit a9022b017a
("ARM64: zynqmp: Add u-boot,dm-pre-reloc to clk nodes")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The sam9x60 qspi controller uses 2 clocks, one for the peripheral register
access, the other for the qspi core and phy. Both are mandatory.
Enable the qspi node together with the SST26VF064B qspi nor flash
memory. Booting from the QSPI NOR flash is now possible.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
sama5's SFR has at offset 0x04 the DDR Configuration Register,
while sam9x60's SFR contains the EBI Chip Select Register. Add
a union to reconcile both boards.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
The Special Function Registers (SFR) are present in sam9x5 and
sam9x60 too, rename sama5_sfr to at91_sfr.h.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
