Commit graph

1938 commits

Author SHA1 Message Date
Qianyu Gong
ec93abe6f7 armv8: ls1043a: remove redundant code in board files
gd->env_addr will be initialized in env_init() in
common/env_nowhere.c if CONFIG_ENV_IS_NOWHERE is defined.
So no need to do it again.

Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-05-18 08:51:45 -07:00
Qianyu Gong
869bf86811 armv8/ls1043ardb: fix the limitation of using 'cpld reset'
The current 'cpld reset' will just write global_rst register
but couldn't switch to NOR boot if the board's switches are
for NAND/SD boot. So need to write rcw source registers for
NOR boot as well.

Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-05-18 08:51:44 -07:00
Vincent Siles
12cbf20d78 arm: uniform usage of u32 in ls102x caam config
Mix usage of uint32_t and u32 fixed in favor of u32.

Signed-off-by: Vincent Siles <vincent.siles@provenrun.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-05-18 08:51:44 -07:00
Vincent Siles
15b96ad831 arm: Fix SCFG ICID reg addresses
On the LS102x boards, in order to initialize the ICID values of
masters, the dev_stream_id array holds absolute offsets from the
base of SCFG.

In ls102xa_config_ssmu_stream_id, the base pointer is cast to
uint32_t * before adding the offset, leading to an invalid address.
Casting it to void * solves the issue.

Signed-off-by: Vincent Siles <vincent.siles@provenrun.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-05-18 08:51:44 -07:00
Prabhakar Kushwaha
6f3819fe30 armv8: ls2080a: Update MAINTAINERS file
Update MAINTAINERS file for ls2080aqds and ls2080ardb platforms.

Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-05-17 09:27:15 -07:00
Shengzhou Liu
aa7a2226b5 armv8/ls2080ardb: Update DDR timing to support more UDIMMs
Optimize DDR timing for good margins to support new Transcend
and Apacer DDR4 UDIMM besides current Micron UDIMM.

Verified 1333MT/s, 1600MT/s, 1866MT/s, 2133MT/s rate with
following UDIMM on LS2080ARDB.
 - Micron UDIMM: MTA18ASF1G72AZ-2G1A1Z
 - Apacer UDIMM: 78.C1GM4.AF10B
 - Transcend UDIMM: TS1GLH72V1H

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-05-17 09:26:59 -07:00
Shengzhou Liu
074596c0b5 armv8/ls1043: Add workaround for DDR erratum A-008850
Barrier transactions from CCI400 need to be disabled till
the DDR is configured, otherwise it may lead to system hang.
The patch adds workaround to fix the erratum.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-05-17 09:26:19 -07:00
Robert P. J. Day
1cc0a9f496 Fix various typos, scattered over the code.
Spelling corrections for (among other things):

* environment
* override
* variable
* ftd (should be "fdt", for flattened device tree)
* embedded
* FTDI
* emulation
* controller
2016-05-05 21:39:26 -04:00
Tom Rini
814013253f Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2016-04-13 07:19:50 -04:00
York Sun
3c1d218a1d armv8: LS2080A: Consolidate LS2080A and LS2085A
LS2080A is the primary SoC, and LS2085A is a personality with AIOP
and DPAA DDR. The RDB and QDS boards support both personality. By
detecting the SVR at runtime, a single image per board can support
both SoCs. It gives users flexibility to swtich SoC without the need
to reprogram the board.

Signed-off-by: York Sun <york.sun@nxp.com>
CC: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2016-04-06 10:26:46 -07:00
Shaohui Xie
ce96ba4b84 armv8: ls1043aqds: make sure fixed-link property is big endian
When setting fixed-link property to DTS, the values should be converted
with using cpu_to_fdt32 so that to have correct value on little endian
Soc.

Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-04-06 08:34:55 -07:00
Tom Rini
59c9e9b408 mx6slevk: imximage.cfg: update to fix tINIT3 and tIH-CA violations
Having had a similar board and memory part under logic analyzer, a
tINIT3 violation was measured.  The fix was involved keeping tXPR and
SDE_to_RST at the power-on defaults and setting RST_to_CKE the JEDEC
value for LPDDR2.  There was also a tIH-CA violation and this was
resolved by writing the default value in rather than what the script
here uses.

Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-04-03 19:18:45 +02:00
Tom Rini
2249b5a55a mx6qarm2: imximage_mx6dl.cfg update to fix tINIT3 violation
Having had a similar board and memory part under logic analyzer, a
tINIT3 violation was measured.  The fix was involved keeping tXPR and
SDE_to_RST at the power-on defaults and setting RST_to_CKE the JEDEC
value for LPDDR2.

Cc: Jason Liu <jason.hui.liu@nxp.com>
Cc: Ye Li <ye.li@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-04-03 19:18:20 +02:00
Fabio Estevam
30ba8eb0d3 mx6sabresd: Remove unneeded enable_lvds() function
enable_lvds() function only set bits IOMUXC_GPR2_DATA_WIDTH_CH0_18BIT and
IOMUXC_GPR2_DATA_WIDTH_CH1_18BIT, but these bits were already set
previously inside setup_display().

We can safely remove enable_lvds() then.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-04-03 19:14:43 +02:00
Mateusz Kulikowski
e162c6b1a7 usb: Rename ehci-fsl.h to ehci-ci.h
Most of ehci-fsl header describe USB controller
designed by Chipidea and used by various SoC vendors.

This patch renames it to a generic header: ehci-ci.h
Contents of file are not changed (so it contains several
references to freescale SoCs).

Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Simon Glass <sjg@chromium.org>
2016-04-01 17:18:10 -04:00
Rai Harninder
ed2530d096 armv8/ls2080ardb: Enable VID support
This patch enable VID support for ls2080ardb platform.
It uses the common VID driver.

Signed-off-by: Rai Harninder <harninder.rai@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-03-29 08:46:24 -07:00
Saksham Jain
85bb389654 SECURE BOOT: Change fsl_secboot_validate func to pass image addr
Use a pointer to pass image address to fsl_secboot_validate(),
instead of using environmental variable "img_addr".

Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-03-29 08:46:23 -07:00
Saksham Jain
c4666cf695 SECURE BOOT: Halt execution when secure boot fail
In case of fatal failure during secure boot execution (e.g. header
not found), reset is asserted to stop execution. If the RESET_REQ
is not tied to HRESET, this allows the execution to continue.

Add esbh_halt() after the reset to make sure execution stops.

Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-03-29 08:46:23 -07:00
Saksham Jain
fcfdb6d580 armv8: ls2080rdb: ls2080qds: Add secure boot support
Sec_init has been called at the beginning to initialize SEC Block
(CAAM) which is used by secure boot validation later for both ls2080a
qds and rdb. 64-bit address in ESBC Header has been enabled. Secure
boot defconfigs are created for boards (NOR boot).

Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-03-29 08:46:20 -07:00
Saksham Jain
fd6dbc98a7 armv8: fsl-lsch3: Add new header for secure boot
For secure boot, a header is used to identify key table, signature
and image address. A new header structure is added for lsch3.

Currently key extension (IE) feature is not supported. Single key
feature is not supported. Keys must be in table format. Hence, SRK
(key table) must be present. Max key number has increase from 4 to
8. The 8th key is irrevocable. A new barker Code is used.

Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-03-29 08:46:20 -07:00
Fabio Estevam
779594d335 mx6sabresd: Use VESA 1024x768 timings
VESA 1024x768 results in much more accurate timings.

Based on the patch from Soeren Moch for the tbs2910 board.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-03-25 14:05:24 +01:00
Stuart Yoder
e91f1deca5 armv8: ls2080a: Update fdt path for fsl-mc node
The fsl-mc node has been moved under /soc, so update
the path references accordingly.  Backwards compatibility
is retained for /fsl-mc.

Delete backwards compatibility for the completely obsolete
/fsl,dprc@0.

Signed-off-by: Stuart Yoder <stuart.yoder@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-03-24 11:43:31 -07:00
Wenbin Song
ec44289db5 armv8/ls1043aqds: Return i2c mux to default chennel
Return i2c mux to the default channel after accessing retimer.

Signed-off-by: Wenbin Song <wenbin.song@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-03-21 12:42:15 -07:00
Wenbin Song
1be8d10be4 freescale: vid: Return i2c mux to default channel
IR chip is on one of the channels on multiplexed I2C-bus.
Reset to default channel after accessing.

Signed-off-by: Wenbin Song <wenbin.song@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-03-21 12:42:15 -07:00
Prabhakar Kushwaha
0f4b82a555 armv8: ls2085a: Remove phy configuration from QDS and RDB
As phy_connect and phy_config are being called from DPAA2 driver.
Remove calling of mentioned function from board file.

Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-03-21 12:42:14 -07:00
Shaohui Xie
abc7d0f75c armv8: ls2080ardb: invert irq pins polarity for AQR405 PHY
To use AQR405 PHY's interrupt, we need to invert the relative IRQ pins
polarity by setting IRQCR register, because AQR405 interrupt is low
active but GIC accepts high active.

Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-03-21 12:42:10 -07:00
Simon Glass
73223f0e1b Kconfig: Move CONFIG_FIT and related options to Kconfig
There are already two FIT options in Kconfig but the CONFIG options are
still in the header files. We need to do a proper move to fix this.

Move these options to Kconfig and tidy up board configuration:

   CONFIG_FIT
   CONFIG_OF_BOARD_SETUP
   CONFIG_OF_SYSTEM_SETUP
   CONFIG_FIT_SIGNATURE
   CONFIG_FIT_BEST_MATCH
   CONFIG_FIT_VERBOSE
   CONFIG_OF_STDOUT_VIA_ALIAS
   CONFIG_RSA

Unfortunately the first one is a little complicated. We need to make sure
this option is not enabled in SPL by this change. Also this option is
enabled automatically in the host builds by defining CONFIG_FIT in the
image.h file. To solve this, add a new IMAGE_USE_FIT #define which can
be used in files that are built on the host but must also build for U-Boot
and SPL.

Note: Masahiro's moveconfig.py script is amazing.

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Add microblaze change, various configs/ re-applies]
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-03-14 19:18:07 -04:00
Fabio Estevam
ae765f3a82 mx6slevk: Fix the power up of the Ethernet PHY
GPIO4_21 is the LAN8720 power pin, not the LAN8720 reset pin.

Fix that, so that we can have Ethernet functional again.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-03-13 09:50:02 -04:00
Fabio Estevam
9feec162af mx6qarm2: Update maintainer's emails
Use the new NXP emails.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-03-02 14:49:13 +01:00
Fabio Estevam
047cc75df6 MAINTAINERS: Update Peng Fan's email address
Use Peng Fan's new NXP email address in MAINTAINERS files.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
2016-03-02 14:48:52 +01:00
Alison Wang
a08b1921b4 armv7: ls102xa: Move smmu and stream id initialization into the common soc code
The initialization for smmu and stream id is moved into the common soc
code.

Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-02-24 08:51:15 -08:00
Zhao Qiang
a12a0ef89e board: ls1043ardb: Modify pin-muxing code for USB and QE-HDLC
QE-HDLC and USB multi-use the pins, modify the pin-muxing code
for them, when set "hwconfig=qe-hdlc" in uboot, assign the pins
to QE-HDLC, if not, assgin it to USB

Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-02-24 08:51:15 -08:00
Zhao Qiang
110171dcef board: ls1043rdb: Move USB muxing config to config_board_mux
Pin-muxing code should be in config_board_mux, move USB muxing
config to config_board_mux.

Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-02-24 08:51:15 -08:00
Zhao Qiang
d3e6d30cef board: ls1043ardb: Add micro QE support for ls1043ardb
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-02-24 08:51:14 -08:00
Qianyu Gong
5a7c40bea6 armv8/ls1043aqds: Add USB support for ls1043aqds
Add USB XHCI support for ls1043qds board.

Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-02-24 08:51:14 -08:00
Qianyu Gong
2459afb1a7 qe: move drivers/qe/qe.h to include/fsl_qe.h
As the QE firmware struct is shared with Fman, move the header file
out of drivers/qe/.

Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-02-24 08:51:13 -08:00
Alison Wang
70097027d2 arm: ls1021a: Add QSPI or IFC support in SD boot for LS1021AQDS board
As QSPI and IFC are pin-multiplexed on LS1021A, only IFC is supported
in SD boot now. For the customer's demand, QSPI needs to be supported
in SD boot too.

This patch adds QSPI or IFC support in SD boot according to the
corresponding defconfig. For detail, ls1021aqds_sdcard_ifc_defconfig
is used to support IFC in SD boot and ls1021aqds_sdcard_qspi_defconfig
is used to support QSPI in SD boot.

Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-02-24 08:40:56 -08:00
Tom Rini
595af9db24 Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2016-02-21 07:56:16 -05:00
Fabio Estevam
2b8e8d2671 mx7dsabresd: Make 'ums' command functional
When running the 'ums' command we get:

=> ums 0 mmc 0
UMS: disk start sector: 0x0, count: 0xe18000
g_dnl_register: failed!, error: -22
ERROR: g_dnl_register failed
at common/cmd_usb_mass_storage.c:107/do_usb_mass_storage()

Fix this by initializing USB OTG1 port as USB device mode instead of host.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-02-21 11:13:27 +01:00
Fabio Estevam
88e826be45 mx7dsabresd: Use Adrian's NXP email address
Use the new NXP email address for the board maintainer.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-02-21 11:12:32 +01:00
Bin Meng
a187559e3d Use correct spelling of "U-Boot"
Correct spelling of "U-Boot" shall be used in all written text
(documentation, comments in source files etc.).

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
2016-02-06 12:00:59 +01:00
Peng Fan
fb0d042814 imx: mx6: implement board_mmc_get_env_dev
Implement board_mmc_get_env_dev for the boards.

Following is examples:
SD1/SD2/SD3: return devno;
SD2/SD3: return devno - 1;
SD2/SD4: if (devno == 2), return dev - 2; return dev - 1;

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-02-04 10:13:53 +01:00
Peng Fan
62d8cce9f3 imx: mx7dsabresd: move mmc_get_env_devno to soc code
Move mmc_get_env_devno to soc.c and rename to mmc_get_env_dev to
match the one in common/env_mmc.c.
Introduce a weak function board_mmc_get_env_dev. Different
boards can implement this according to sdhc controller which
is used by the board.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-02-04 10:13:45 +01:00
Ye Li
85eb095216 imx: mx6sxsabresd: Add MCIMX28LCD display support
The i.MX6SX SABRESD board supports MCIMX28LCD (800x480x24) at LCDIF1
port, enable this display feature by adding relevant BSP codes
and configurations.

Signed-off-by: Ye Li <ye.li@nxp.com>
2016-02-02 21:27:15 +01:00
Ye Li
214c3f0f99 imx: MX6DQ{P}/DL:SABRESD Fix bmode eMMC failure
The BOOTCFG value used by bmode for SABRESD eMMC boot are actually for SD card.
Fixed the value to correct one.

Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-02-02 21:22:04 +01:00
Fabio Estevam
529a671279 mx6slevk: Fix the reset delay for the the LAN8720 PHY
Since commit 59370f3fcd ("net: phy: delay only if reset handler is
registered") Ethernet is no longer functional.

This commit does not have an issue in itself, but it revelead a problem
with the Ethernet initialization.

According to the LAN8720 datasheet tpurstd (time that reset line should
stay asserted) is 25ms.

So do as suggested in order to have Ethernet working again.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-02-02 21:18:44 +01:00
Ye Li
cf94a3427a imx: mx6sxsabreauto: Add support for mx6sx SABREAUTO board
Initial version for mx6sx SABREAUTO board support with features:
PMIC, QSPI, NAND flash, SD/MMC, USB, Ethernet, I2C, IO Expander.

Signed-off-by: Ye Li <ye.li@nxp.com>
2016-02-02 21:04:21 +01:00
Tom Rini
82d72a1b99 Merge branch 'master' of git://git.denx.de/u-boot-net 2016-01-28 18:42:10 -05:00
Bin Meng
9ccb309651 arm: ls1021atwr: Do not wrap pci_eth_init() with CONFIG_TSEC_ENET
The call to pci_eth_init() should not be wrapped with CONFIG_TSEC_ENET.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-28 12:22:44 -06:00
Bin Meng
c712df1d1d powerpc: p1010rdb: Do not wrap pci_eth_init() with CONFIG_TSEC_ENET
The call to pci_eth_init() should not be wrapped with CONFIG_TSEC_ENET.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-28 12:22:41 -06:00
Bin Meng
1adc09544f powerpc: mpc8548cds: Do not wrap pci_eth_init() with CONFIG_TSEC_ENET
The call to pci_eth_init() should not be wrapped with CONFIG_TSEC_ENET.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-28 12:22:37 -06:00
Bin Meng
4521ae9dca powerpc: mpc8572ds: Do not wrap pci_eth_init() with CONFIG_TSEC_ENET
The call to pci_eth_init() should not be wrapped with CONFIG_TSEC_ENET.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-28 12:22:33 -06:00
Bin Meng
98ae83b5e1 powerpc: c29xpcie: Do not wrap pci_eth_init() with CONFIG_TSEC_ENET
The call to pci_eth_init() should not be wrapped with CONFIG_TSEC_ENET.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-28 12:22:30 -06:00
Bin Meng
89c97842db powerpc: bsc9132qds: Do not wrap pci_eth_init() with CONFIG_TSEC_ENET
The call to pci_eth_init() should not be wrapped with CONFIG_TSEC_ENET.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-28 12:22:27 -06:00
Tom Rini
cd85bec36d Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriq 2016-01-27 15:05:36 -05:00
Qianyu Gong
b0f20caf65 armv8/ls1043aqds: add QSPI boot support
Enable the U-Boot Driver Model(DM) to use the Freescale QSPI driver.

Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-27 08:29:09 -08:00
Gong Qianyu
166ef1e90c armv8/ls1043aqds: add QSPI support in SD boot
QSPI and IFC are pin-multiplexed on LS1043A. So we use
ls1043aqds_sdcard_ifc_defconfig to support IFC in SD boot and
ls1043aqds_sdcard_qspi_defconfig to support QSPI in SD boot.

Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-27 08:28:55 -08:00
Shaohui Xie
8c35cc3b7e armv8/ls1043aqds: Select lpuart pins of various muxes
Set Board Configuration Register to select the lpuart pins of various
muxes.

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-27 08:13:12 -08:00
Aneesh Bansal
856b284617 secure_boot: change error handler for esbc_validate
In case of error while executing esbc_validate command, SNVS
transition and issue of reset is required only for secure-boot.
If boot mode is non-secure, this is not required.

Similarly, esbc_halt command which puts the core in Spin Loop
is applicable only for Secure Boot.

Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Acked-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-27 08:13:03 -08:00
Aneesh Bansal
d041288586 secure_boot: enable chain of trust for ARM platforms
Chain of Trust is enabled for ARM platforms (LS1021 and LS1043).
In board_late_init(), fsl_setenv_chain_of_trust() is called which
will perform the following:
- If boot mode is non-secure, return (No Change)
- If boot mode is secure, set the following environmet variables:
   bootdelay = 0 (To disable Boot Prompt)
   bootcmd = CONFIG_CHAIN_BOOT_CMD (Validate and execute Boot script)

Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Acked-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-27 08:12:49 -08:00
Aneesh Bansal
0a6b2714ad secure_boot: create function to determine boot mode
A function is created to detrmine if the boot mode is secure
or non-secure for differnt SoC's.

Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Acked-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-27 08:12:42 -08:00
Tom Rini
d82477748d Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx 2016-01-25 16:45:00 -05:00
Ying Zhang
2f66a828f7 powerpc/board/t4240rdb: Enable VID support
The fuse status register provides the values from on-chip
voltage ID efuses programmed at the factory. These values
define the voltage requirements for the chip. u-boot reads
FUSESR and translates the values into the appropriate
commands to set the voltage output value of an external
voltage regulator.

Signed-off-by: Ying Zhang <b40530@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-25 12:38:05 -08:00
Ying Zhang
cabe4d2f19 board/freescale/common: Check IR chip mode for VID support
IR chip on all the boards are required to be used in Intel mode
to support VID. VDD will not be adjusted if IR chip is used in
other modes.

Signed-off-by: Ying Zhang <b40530@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-25 12:37:03 -08:00
Prabhakar Kushwaha
2c0d69713c powerpc: mpc85xx: Move set_liodns, setup_portals to common boot seq
Users migrating Freescale's PowerPC SoC U-Boot code to their custom
board, often overlook the need to execute set_liodns() and
setup_portals() being called by platform files.

So Move set_liodns() and setup_portals() to common u-boot boot
sequence

Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-25 12:13:31 -08:00
Aneesh Bansal
b055a0fd86 SECURE BOOT: support for validation of dynamic image
Some images to be validated are relocated to a dynamic
address at run time. So, these addresses cannot be known
befor hand while signing the images and creating the header
offline.
So, support is required to pass the image address to the
validate function as an argument.
If an address is provided to the function, the address
field in Header is not read and is treated as a reserved
field.

Signed-off-by: Saksham Jain <saksham@freescale.com>
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Acked-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-25 08:24:16 -08:00
Aneesh Bansal
6629261ddd SECURE BOOT: separate function created for signature
The code for image hash calculation, hash calculation from
RSA signature and comparison of hashes has been mobed to a
separate function.

Signed-off-by: Saksham Jain <saksham@freescale.com>
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Acked-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-25 08:24:16 -08:00
Aneesh Bansal
94ba5e4140 SECURE BOOT: separate functions for reading keys
Separate functions are created for reading and checking the
sanity of Public keys:
- read_validate_single_key
- read_validate_ie_tbl
- read_validate_srk_table

Signed-off-by: Saksham Jain <saksham@freescale.com>
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Acked-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-25 08:24:16 -08:00
Aneesh Bansal
bc71f926e3 SECURE BOOT: change prototype of fsl_secboot_validate function
The prototype and defination of function fsl_secboot_validate
has been changed to support calling this function from another
function within u-boot.
Only two aruments needed:
1) header address - Mandatory
2) SHA256 string - optional

Signed-off-by: Saksham Jain <saksham@freescale.com>
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Acked-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-25 08:24:16 -08:00
Gong Qianyu
98d9aa4013 freescale/qixis: Add support for booting from SD/QSPI
1.Use "qixis_reset sd" to boot from SD
2.Use "qixis_reset sd_qspi" to boot from SD with QSPI support
3.Use "qixis_reset qspi" to boot from QSPI flash

On some SoCs such as LS1021A and LS1043A, IFC and QSPI could be
pin-multiplexed. So the switches are different between SD boot with
IFC support and SD boot with QSPI support. The default booting from
SD is with IFC support.

Once QSPI is enabled(IFC disabled), only use I2C to access QIXIS.

Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-25 08:24:15 -08:00
Shaohui Xie
58e4ad1dee armv8/ls1043aqds: Add support for >2GB memory
This patch also exposes the complete DDR region(s) to Linux.

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-25 08:24:14 -08:00
Peng Fan
6e1a41cd6a imx: mx7dsabresd: support nand
Add pinmux settings.
Add related macro definitions.
Nand pin conflicts with emmc, so if want to enable nand, need to do
hardware rework. After hardware rework, define CONFIG_NAND_MXS in
board header file.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-01-24 12:09:44 +01:00
Fabio Estevam
4897d950b7 mx25pdk: Remove lowlevel_init.S file
As the lowlevel_init function is empty we should better
remove this assembly file entirely and use a dummy C
function instead.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-01-24 11:52:45 +01:00
Masahiro Yamada
61a4392a36 m68k: M54418TWR: drop board/freescale/m54418twr/config.mk
The board/freescale/m54418twr/config.mk defined TEXT_BASE, which has
the same value as CONFIG_SYS_TEXT_BASE.  The TEXT_BASE is referenced
by two files:
 - arch/m68k/cpu/mcf5445x/start.S and include/
 - include/configs/M54418TWR.h

Replace the references with CONFIG_SYS_TEXT_BASE and delete
board/freescale/m54418twr/config.mk.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Angelo Dureghello <angelo at sysam.it>
2016-01-20 10:19:34 -05:00
Masahiro Yamada
c6e18144b6 m68k: move CONFIG_SYS_TEXT_BASE to defconfig files
For historical reason, CONFIG_SYS_TEXT_BASE has been specified
in various ways:

[1] by board/${VENDOR}/${BOARD}/config.mk

[2] by CONFIG_SYS_EXTRA_OPTIONS
    (This was "options" field of boards.cfg before Kconfig conversion)

[3] by include/configs/${BOARD}.h

[4] by configs/${BOARD}_defconfig

Most of M68K boards use either [1] or [2], both of which we want to
deprecate.  Switch them into [4], which is the newest way (Kconfig).

We still allow [3] too, because it is still used by many boards and
we expect much time for conversion.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Angelo Dureghello <angelo at sysam.it>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-01-20 10:19:34 -05:00
Tom Rini
5b8031ccb4 Add more SPDX-License-Identifier tags
In a number of places we had wordings of the GPL (or LGPL in a few
cases) license text that were split in such a way that it wasn't caught
previously.  Convert all of these to the correct SPDX-License-Identifier
tag.

Signed-off-by: Tom Rini <trini@konsulko.com>
2016-01-19 08:31:21 -05:00
Ben Whitten
192bc6948b Fix GCC format-security errors and convert sprintfs.
With format-security errors turned on, GCC picks up the use of sprintf with
a format parameter not being a string literal.

Simple uses of sprintf are also converted to use strcpy.

Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
Acked-by: Wolfgang Denk <wd@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-01-14 22:11:34 -05:00
Stephen Warren
7c4213f6a5 block: pass block dev not num to read/write/erase()
This will allow the implementation to make use of data in the block_dev
structure beyond the base device number. This will be useful so that eMMC
block devices can encompass the HW partition ID rather than treating this
out-of-band. Equally, the existence of the priv field is crying out for
this patch to exist.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-01-13 21:05:18 -05:00
Fabio Estevam
c5f18a0b69 MAINTAINERS/mailmap: Update my email address
Update my email address to the NXP account.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-01-11 11:22:43 -05:00
Tom Rini
b685c7348c Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2016-01-08 10:18:18 -05:00
York Sun
2f231025bc MAINTAINERS, .mailmap: Update my email address
Change from yorksun@freescale.com to york.sun@nxp.com.

Signed-off-by: York Sun <york.sun@nxp.com>
2016-01-08 10:15:46 -05:00
Ye.Li
7ea191aa10 pfuze: Fix unsigned variable for less-than-zero comparison
According to the Coverity result, a unsigned int variable is used fo less-
than-zero comparison, the result is never true. Need to fix the variable
type to signed int.

Signed-off-by: Ye.Li <B37916@freescale.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2016-01-07 17:48:25 +01:00
Fabio Estevam
a307760ab4 mx6sabresd: Simplify the Ethernet PHY configuration
As per the AR8031 datasheet:

"For a reliable power on reset, suggest to keep asserting the reset
low long enough (10ms) to ensure the clock is stable and clock-to-reset
1ms requirement is satisfied."

So do as suggested and also add a 100us delay after deasserting the
reset line to guarantee that the PHY ID can be read correctly and the
Atheros 8031 PHY driver can be loaded automatically.

This results in a simpler code.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-07 17:47:12 +01:00
Miao Yan
18d3f46995 qemu-ppce500: pass 'range_id' around in pci_map_region
In pci_map_region(), pass 'range_id' to fdt_read_range(),
otherwise the same address will be mapped again in other
calls to pci_map_region()

Signed-off-by: Miao Yan <yammiaobest@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
2016-01-04 12:25:34 -05:00
Tom Rini
f1993ca066 Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2016-01-03 10:32:24 -05:00
Peng Fan
ccf4326bac imx: mx6qsabreauto: support lvds display
Move setup_display from board_early_init_f to board_init.
Add more clock settings.
Add blacklight iomux setting.
Add display_info_t info for the lvds screen.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-01-03 16:03:14 +01:00
Mingkai Hu
1c5c6a5761 armv8/ls1043aqds/rcw: change core frequency to 1600MHz
Change RCW for SD boot and NAND boot.

Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-12-17 08:52:18 +08:00
Mingkai Hu
e2f019d783 armv8/ls1043ardb/rcw: change core frequency to 1600MHz
Change RCW for SD boot and NAND boot.

Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-12-17 08:52:18 +08:00
Aneesh Bansal
9711f52806 armv8/ls1043ardb: add SECURE BOOT target for NOR
LS1043ARDB Secure Boot Target from NOR has been added.
- Configs defined to enable esbc_validate.
- ESBC Address in header is made 64 bit.
- SMMU is re-configured in Bypass mode.

Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-12-15 08:57:35 +08:00
York Sun
c04921414c armv8: fsl-layerscale: Rewrite reserving memory for MC and debug server
MC and debug server are not board-specific. Move reserving memory to SoC
file, using the new board_reserve_ram_top function. Reduce debug server
memory by 2MB to make room for secure memory.

In the system with MC and debug server, the top of u-boot memory
is not the end of memory. PRAM is not used for this reservation.

Signed-off-by: York Sun <yorksun@freescale.com>
2015-12-15 08:57:33 +08:00
York Sun
c107c0c05c armv8: fsl-layerscape: Make DDR non secure in MMU tables
DDR has been set as secure in MMU tables. Non-secure master such
as SDHC DMA cannot access data correctly. Mixing secure and non-
secure MMU entries requirs the MMU tables themselves in secure
memory. This patch moves MMU tables into a secure DDR area.

Early MMU tables are changed to set DDR as non-secure. A new
table is added into final MMU tables so secure memory can have
2MB granuality.

gd->secure_ram tracks the location of this secure memory. For
ARMv8 SoCs, the RAM base is not zero and RAM is divided into several
banks. gd->secure_ram needs to be maintained before using. This
maintenance is board-specific, depending on the SoC and memory
bank of the secure memory falls into.

Signed-off-by: York Sun <yorksun@freescale.com>
2015-12-15 08:57:33 +08:00
Yao Yuan
7ba0261810 arm: ls1021a: merge SoC specific code in a separate file
Create a soc.c file to put the code for soc special settings.

Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-12-13 18:27:29 -08:00
Shaohui Xie
e994dddbbe armv8/ls1043ardb: Add support for >2GB memory
This patch also expose the complete DDR region(s) to Linux.

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-12-13 18:27:29 -08:00
Shaohui Xie
1aaf3f9ae4 freescale: fman: make sure phy-handle property is big endian
When creating phy-handle property, an unsigned int value is created by
fdt_create_phandle, and memcpy is used to get the value, since DTS is
big endian, the value cannot be used directly on little endian SoCs,
it should be converted by cpu_to_fdt32.

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-12-13 18:27:28 -08:00
York Sun
3901978d42 armv8/ls2080ardb: Update DDR settings for four chip-select case
When 4 chip-selects are used, vref should use range 1 and CDT uses 80 ohm,
and 2T timing is enabled.

Signed-off-by: York Sun <yorksun@freescale.com>
2015-12-13 18:27:28 -08:00
York Sun
c4243ac9e2 armv8/ls2080aqds: Update DDR settings for four chip-select case
When 4 chip-selects are used, vref should use range 1 and CDT uses 80 ohm,
and 2T timing is enabled.

Signed-off-by: York Sun <yorksun@freescale.com>
2015-12-13 18:27:28 -08:00
Peng Fan
53cc647dc6 imx: mx7dsabresd: Add QSPI support
Support qspi flashes for mx7dsabresd
1. introduce pin mux settings
2. enable qspi clock
3. introduce related macro definitions

Default QSPI is not enabled, since we need hardware rework to use QSPI,
see SPF-28590, page 9:
"
QSPI signals are muxed with EPDC_D[7:0]
When using QSPI: de-populate R388-R391, R396-R399
populate R392-R395, R299, R300
"

After hardware rework, define CONFIG_FSL_QSPI in mx7dsabresd.h. qspi
flashes can be deteced and read/erase/write. Log info:
"
=> sf probe
SF: Detected MX25L51235F with page size 256 Bytes, erase size 64 KiB, total 64 MiB
=> sf read 0x80000000 0 0x4000000
device 0 whole chip
SF: 67108864 bytes @ 0x0 Read: OK
=> sf erase 0 0x4000000
SF: 67108864 bytes @ 0x0 Erased: OK
=> sf write 0x80000000 0 0x4000000
device 0 whole chip
SF: 67108864 bytes @ 0x0 Written: OK
"

Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Adrian Alonso <aalonso@freescale.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
2015-12-11 22:12:23 +05:30
Fabio Estevam
29bc24ec4f mx6sxsabresd: Fix Ethernet PHY reset sequence
Since commit 59370f3fcd ("net: phy: delay only if reset handler is
registered") Ethernet is no longer functional.

This commit does not have an issue in itself, but it revelead a problem
with the Ethernet initialization.

Fix this by calling enable_fec_anatop_clock() earlier and also
by adding a 10ms reset delay as recommended in the AR8031 datasheet.

Suggested-by: Jörg Krause <joerg.krause@embedded.rocks>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2015-12-07 14:55:24 +01:00
Prabhakar Kushwaha
5380335e66 board/ls2080qds: Fix typo in README for QSGMII riser card
DPMACx to PHY mapping for SGMII is mentioned as QSGMII.

So fix typo in README for QSGMII rise card.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: Change from ls2085aqds to ls2080aqds]
Reviewed-by: York Sun <yorksun@freescale.com>
2015-11-30 09:11:12 -08:00
Gong Qianyu
7023100971 armv8/ls1043ardb: add USB support
Add support for the third USB controller for LS1043A.

Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-11-30 09:11:11 -08:00
Shaohui Xie
02b5d2ed86 armv8/ls1043aqds: add LS1043AQDS board support
LS1043AQDS Specification:
-------------------------
Memory subsystem:
 * 2GByte DDR4 DIMM
 * 128 Mbyte NOR flash single-chip memory
 * 512 Mbyte NAND flash
 * 16 Mbyte high-speed SPI flash
 * SD connector to interface with the SD memory card

Ethernet:
 * Two RGMII ports
 * XFI 10G port
 * SGMII
 * QSGMII with 4x 1G ports

PCIe: supports Gen 1 and Gen 2

SATA 3.0: one SATA 3.0 port

USB 3.0: two micro AB connector and one type A connector

UART: supports two UARTs up to 115200 bps for console

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
[York Sun: Add CONFIG_SYS_NS16550=y in defconfig]
Reviewed-by: York Sun <yorksun@freescale.com>
2015-11-30 09:11:10 -08:00
Prabhakar Kushwaha
06b5301043 armv8: ls2085a: Add support of LS2085A SoC
Freescale's LS2085A is a another personality of LS2080A SoC with
support of AIOP and DP-DDR.
This Patch adds support of LS2085A Personality.

Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: Updated MAINTAINERS files
           Dropped #ifdef in cpu.h
           Add CONFIG_SYS_NS16550=y in defconfig]
Reviewed-by: York Sun <yorksun@freescale.com>
2015-11-30 09:10:47 -08:00
Prabhakar Kushwaha
449372148f armv8: LS2080A: Rename LS2085A to reflect LS2080A
LS2080A is a prime personality of Freescale’s LS2085A. It is a non-AIOP
personality without support of DP-DDR, L2 switch, 1588, PCIe endpoint etc.
So renaming existing LS2085A code base to reflect LS2080A (Prime personality)

Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: Dropped #ifdef in cpu.c for cpu_type_list]
Reviewed-by: York Sun <yorksun@freescale.com>
2015-11-30 08:53:04 -08:00
Prabhakar Kushwaha
1730a17db9 driver: net: fsl-mc: Create DPAA2 object at run-time
Freescale's DPAA2 ethernet driver depends upon the static DPL for the
DPRC, DPNI, DPBP, DPIO objects.

Instead of static objects, Create DPNI, DPBP, DPIO objects at run-time.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-11-30 08:53:03 -08:00
Prabhakar Kushwaha
25af413740 armv8: ls2085aqds: Print function name during SerDes error
Print function name along with SerDes Protocol during SerDes Protocol
not supported error.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-11-30 08:53:02 -08:00
Simon Glass
24b852a7a2 Move console definitions into a new console.h file
The console includes a global variable and several functions that are only
used by a small subset of U-Boot files. Before adding more functions, move
the definitions into their own header file.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-11-19 20:27:50 -07:00
Peng Fan
ebe517b63c imx: mx7dsabresd: support lcdif
Support LCDIF for mx7dsabresd board:
1. Add pinmux settings
2. Add VIDEO related macro definition and videomode env settings.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Adrian Alonso <aalonso@freescale.com>
2015-11-12 17:41:20 +01:00
Peng Fan
df67490488 imx: mx6ul_14x14_evk: support lcdif display
Support lcdif display:
1. Add pinmux and pad settings for LCDIF
2. Introduce setup_lcd to do the settings for LCDIF
3. Enable VIDEO related macros in board header files
4. Add a new env videomode which is needed by mxsfb.c. The
   settings for videomode in this patch is for TFT43AB.
5. Tested on mx6ul 14x14/9x9 evk.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
2015-11-12 17:40:53 +01:00
Fabio Estevam
4bdcbe60a1 mx6ul_14x14_evk: Remove empty reset_cpu()
There is really no need to provide an empty reset_cpu() implementation,
so just remove it.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2015-11-12 17:26:32 +01:00
Fabio Estevam
cec6f213b6 mx6sxsabresd: Remove empty reset_cpu()
There is really no need to provide an empty reset_cpu() implementation,
so just remove it.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2015-11-12 17:26:31 +01:00
Fabio Estevam
c0039753cb mx6slevk: Remove empty reset_cpu()
There is really no need to provide an empty reset_cpu() implementation,
so just remove it.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2015-11-12 17:26:31 +01:00
Fabio Estevam
26fbe9e531 mx6sabresd: Remove empty reset_cpu()
There is really no need to provide an empty reset_cpu() implementation,
so just remove it.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2015-11-12 17:26:30 +01:00
Stefano Babic
5f5620ab26 Merge git://git.denx.de/u-boot 2015-11-12 17:13:26 +01:00
Fabio Estevam
9549867c86 ls1043ardb: Add missing config entries to MAINTAINERS
ls1043ardb_nand_defconfig and ls1043ardb_sdcard_defconfig are missing
in the MAINTAINERS file, so add them for completeness.

Reported-by: Albert Aribaud <albert.u.boot@aribaud.net>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2015-11-10 16:52:58 +01:00
Yangbo Lu
bf50be835e mmc: fsl_esdhc: enable EVDD automatic control for SD/MMC Legacy Adapter Card
When detecting SDHC Adapter Card Type 2(SD/MMC Legacy Adapter Card),
enable EVDD automatic control via SDHC_VS. This could support SD card
IO voltage switching for UHS-1 speed mode.

Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-11-02 08:50:29 -08:00
Yangbo Lu
cdc69550d2 mmc: fsl_esdhc: enable dat[4:7] for eMMC4.5 Adapter Card
If adapter card type identification is supported for platform, we would
enable dat[4:7] for eMMC4.5 Adapter Card.

Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-11-02 08:49:51 -08:00
Zhao Qiang
d468377672 t1040d4rdb: assign muxed pins to qe-tdm when set hwconfig qe-tdm
qe-tdm is muxed with diu, if hwconfig setted as qe-tdm,
assign muxed pins to qe-tdm, then delete diu node from
device tree.

Signed-off-by: Zhao Qiang <qiang.zhao@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-11-02 08:48:20 -08:00
tang yuantian
0210a36988 arm: ls1021atwr: optimize the deep sleep latency
It will take more than 1s when wake up from deep sleep. Most of the
time is spent on outputing information. This patch reduced the deep
sleep latency by:
1. avoid outputing system informaton
2. remove flush cache after DDR restore
3. skip reloading second stage uboot binary when SD boot

Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-30 09:19:48 -07:00
Aneesh Bansal
6ec9aef2ce SECURE_BOOT: Correct reading of ITS bit
The ITS bit was being read incorrectly beacause of operator
precedence. The same ahs been corrected.

Signed-off-by: Lawish Deshmukh <lawish.deshmukh@freescale.com>
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-30 09:19:47 -07:00
Adrian Alonso
78e9ca52ed mx7dsabresd: add secure boot support
Add secure boot support for mx7dsabresd target board

Signed-off-by: Adrian Alonso <aalonso@freescale.com>
2015-10-30 15:22:37 +01:00
Peng Fan
e469719c8b imx: mx6sabresd: add i.MX6DQP Sabresd support
Add i.MX6DQP-Sabresd board support:
1. set fdt_file according to board_rev which is set at runtime.
2. Add mx6dqp_ddr_ioregs and calibration value for this board.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
2015-10-30 15:15:36 +01:00
tang yuantian
4632ad773e arm: ls1021a: Add sata support on qds and twr board
Freescale ARM-based Layerscape LS102xA contain a SATA controller
which comply with the serial ATA 3.0 specification and the
AHCI 1.3 specification.
This patch adds SATA feature on ls1021aqds and ls1021atwr boards.

Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-29 10:34:02 -07:00
Gong Qianyu
c7ca8b07fc armv8/ls1043ardb: Add sd boot support
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-29 10:34:02 -07:00
Yangbo Lu
8ef0d5c438 armv8/ls1043ardb: esdhc: Add esdhc support for ls1043ardb
This patch adds esdhc support for ls1043ardb.

Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-29 10:34:01 -07:00
Shaohui Xie
e82973414d armv8/ls1043a: Add Fman support
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-29 10:34:01 -07:00
Gong Qianyu
3ad4472923 armv8/ls1043ardb: Add nand boot support
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-29 10:34:01 -07:00
Mingkai Hu
f3a8e2b7d4 armv8/ls1043ardb: Add LS1043ARDB board support
LS1043ARDB Specification:
-------------------------
Memory subsystem:
 * 2GByte DDR4 SDRAM (32bit bus)
 * 128 Mbyte NOR flash single-chip memory
 * 512 Mbyte NAND flash
 * 16 Mbyte high-speed SPI flash
 * SD connector to interface with the SD memory card

Ethernet:
 * XFI 10G port
 * QSGMII with 4x 1G ports
 * Two RGMII ports

PCIe:
 * PCIe2 (Lanes C) to mini-PCIe slot
 * PCIe3 (Lanes D) to PCIe slot

USB 3.0: two super speed USB 3.0 type A ports

UART: supports two UARTs up to 115200 bps for console

Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
2015-10-29 10:34:01 -07:00
Mingkai Hu
9f3183d2d6 armv8/fsl_lsch3: Change arch to fsl-layerscape
There are two LS series processors are built on ARMv8 Layersacpe
architecture currently, LS2085A and LS1043A. They are based on
ARMv8 core although use different chassis, so create fsl-layerscape
to refactor the common code for the LS series processors which also
paves the way for adding LS1043A platform.

Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-29 10:34:00 -07:00
Shaohui Xie
8225b2fd87 net: Move some header files to include/
The fsl_dtsec.h & fsl_tgec.h & fsl_fman.h can be shared on both ARM
and PPC, move it out of ppc to include/, and change the path in
drivers accordingly.

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-29 10:34:00 -07:00
Mingkai Hu
435acd83b2 armv7/ls1021a: move ns_access to common file
Config Security Level Register is different between different SoCs,
so put the CSL register definition into the arch specific directory.

Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-29 10:33:58 -07:00
Aneesh Bansal
7bcb0eb285 Pointers in ESBC header made 32 bit
For the Chain of Trust, the esbc_validate command supports
32 bit fields for location of the image. In the header structure
definition, these were declared as pointers which made them
64 bit on a 64 bit core.

Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-29 10:33:57 -07:00
Alison Wang
947cee1127 arm: ls1021a: Add QSPI or IFC support in SD boot
As QSPI and IFC are pin-multiplexed on LS1021A, only IFC is supported in
SD boot now. For the customer's demand, QSPI needs to be supported in SD
boot too.

This patch adds QSPI or IFC support in SD boot according to the
corresponding defconfig. For detail, ls1021atwr_sdcard_ifc_defconfig is
used to support IFC in SD boot and ls1021atwr_sdcard_qspi_defconfig is
used to support QSPI in SD boot.

Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-26 09:09:57 -07:00
Anthony Felice
4b8cdd484c vf610twr: Fix typo in DRAM init
This commit fixes a typo in vf610twr DRAM init that was causing a hang in
U-Boot for the Vybrid Tower. This typo was introduced in commit 3f353cecc
(vf610: refactor DDRMC code).

Signed-off-by: Anthony Felice <tony.felice@timesys.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
2015-10-16 07:21:09 -04:00
Anthony Felice
42e550d44b vf610twr: Fix typo in DRAM init
This commit fixes a typo in vf610twr DRAM init that was causing a hang in
U-Boot for the Vybrid Tower. This typo was introduced in commit 3f353cecc
(vf610: refactor DDRMC code).

Signed-off-by: Anthony Felice <tony.felice@timesys.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
2015-10-16 09:33:26 +02:00
Albert ARIBAUD \\(3ADEV\\)
3f353ceccb vf610: refactor DDRMC code
The VF610 DDRMC driver code contains settings which are
board-specific. Move these out to boards so that new boards
can define their own without having to modify the driver.

Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
2015-10-02 10:42:31 +02:00
Peng Fan
60dba18801 imx: mx7dsabresd: drop code for CONFIG_CMD_BMODE
We use outer pmic reset and drop internal reset signal, bmode will
not work as expected, so drop boot mode code for 7dsabresd board.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Adrian Alonso <aalonso@freescale.com>
2015-09-24 11:32:18 +02:00
Peng Fan
0b530b140a imx: boards: Add maintainers info
Add MAINTAINERS info for mx6slevk_spl, mx6ul_9x9_evk and mx6qpsabreauto.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
2015-09-24 11:28:59 +02:00
Peng Fan
8e4ba5e0ff imx: mx7dsabresd: drop SYS_SOC from board Kconfig
We have defined this kconfig entry in arch/arm/cpu/armv7/mx7/Kconfig,
no need to redefine it in board Kconfig.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
2015-09-20 09:57:00 +02:00
Fabio Estevam
07af555513 mx6ul_14x14_evk: Remove get_board_rev()
get_board_rev() is not actually providing the board revision.

It just returns the CPU revision instead.

As the CPU revision is already printed on boot, there is no
reason to have get_board_rev(), so let's remove it.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2015-09-20 09:48:00 +02:00
Fabio Estevam
d547e7ab16 mx6ul_14x14_evk: Staticize when possible
Make the internal symbols static when possible.

This prevents sparse build warnings.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2015-09-20 09:47:59 +02:00
Fabio Estevam
e9c8f0982d mx6ul_14x14_evk: Remove dead code
iox74lv_set() is not used anywhere, so let's remove it.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2015-09-20 09:47:59 +02:00
Fabio Estevam
e0ece17304 mx7dsabresd: Remove get_board_rev()
get_board_rev() is not actually providing the board revision.

It just returns the CPU revision instead.

As the CPU revision is already printed on boot, there is no
reason to have get_board_rev(), so let's remove it.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2015-09-20 09:47:59 +02:00
Fabio Estevam
0df2f01d42 mx7dsabresd: Include USB header
Include <usb/ehci-fsl.h> in order to fix the following sparse warning:

board/freescale/mx7dsabresd/mx7dsabresd.c:538:5: warning: symbol 'board_ehci_hcd_init' was not declared. Should it be static?

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2015-09-20 09:47:59 +02:00
Fabio Estevam
b7d4db2f96 mx7dsabreasd: Remove dead code
iox74lv_set() is not used anywhere, so let's remove it.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2015-09-20 09:47:59 +02:00
Fabio Estevam
72e49e0364 mx7dsabresd: Staticize when possible
Make the internal symbols static when possible.

This prevents sparse build warnings.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2015-09-20 09:47:59 +02:00
Peng Fan
4fae48e8a9 imx: mx7dsabresd set wdog SRS bit
We use trigger pmic reset to reset the board, so set bit SRS to
disable internal WDOG_RESET_B_DEB to make reset stable.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Adrian Alonso <aalonso@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
2015-09-20 09:40:19 +02:00
Fabio Estevam
d6be30fe95 mx6ul_14x14_evk: Add a README file
Add a README file to help users getting started with the board.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2015-09-13 10:54:37 +02:00
Peng Fan
f20562e4c4 mx6: remove SYS_SOC from board Kconfig
Remove duplicated SYS_SOC Kconfig entry from board Kconfig,
because we have this entry in arch/arm/cpu/armv7/mx6/Kconfig.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: "Eric Bénard" <eric@eukrea.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Markus Niebel <Markus.Niebel@tq-group.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Acked-by: Markus Niebel <Markus.Niebel@tq-group.com>
Acked-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2015-09-13 10:37:29 +02:00
Peng Fan
d9cbb264e8 imx: mx6ul: support mx6ul 9x9 evk board
This patch is to support mx6ul_9x9_evk board based on mx6ul_14x14_evk,
the difference between mx6ul 9x9 evk and mx6ul 14x14 evk are:
1. mx6ul 9x9 evk use pfuze3000, while mx6ul 14x14 evk use DCDC.
2. mx6ul 9x9 evk supports 256MB LPDDR2, while mx6ul 14x14 evk
   supports 512MB DDR3
3. mx6ul_9x9_evk use 9x9 package, while mx6ul_14x14_evk use 14x14 package.

This patch add the following:
1. Discard PHYS_SDRAM_SIZE from header file, use imx_ddr_size()
2. Introduce a macro is_mx6ul_9x9_evk using
   CONFIG_IS_ENABLED(TARGET_MX6UL_9X9_EVK) to avoid "#ifdef xxx" in non-SPL
   part. To SPL part, CONFIG_IS_ENABLED(TARGET_MX6UL_9X9_EVK) can not work,
   so still use "#ifdef CONFIG_TARGET_MX6UL_9X9_EVK" to differentiate with
   mx6ul_14x14_evk. And we have no way to dymaically checking this chip
   is 9x9 or 14x14.
3. mx6ul_9x9_evk use pfuze3000, so enabled POWER related configurations.
   POWER related configurations also effect for mx6ul_14x14_evk. But
   power_init_board implementation using 'if (is_mx6ul_9x9_evk())' to
   do initialization for mx6ul_9x9_evk, and do nothing for mx6ul_14x14_evk.
4. mx6ul_9x9_evk use lpddr2 with size 256MB, so add related SPL DRAM
   configurations.
5. Enable CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG and setting dtb file
   according to board_rev and board_name.
6. Add TARGET_MX6UL_9X9_EVK Kconfig entry

Boot Log:
U-Boot SPL 2015.10-rc2-00356-g536ce34 (Sep 06 2015 - 12:22:53)
reading u-boot.img
reading u-boot.img

U-Boot 2015.10-rc2-00356-g536ce34 (Sep 06 2015 - 12:22:53 +0800)

CPU:   Freescale i.MX6UL rev1.0 792 MHz (running at 396 MHz)
CPU:   Commercial temperature grade (0C to 95C) at 41C
Reset cause: POR
Board: MX6UL 9x9 EVK
I2C:   ready
DRAM:  256 MiB
PMIC: PFUZE3000 DEV_ID=0x30 REV_ID=0x11
MMC:   FSL_SDHC: 0, FSL_SDHC: 1
In:    serial
Out:   serial
Err:   serial
Net:   FEC1
Hit any key to stop autoboot:  0

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
2015-09-13 10:32:44 +02:00
Adrian Alonso
1a8150d4b1 imx: mx7dsabresd: Add support for MX7D SABRESD board
* Add i.MX7D SABRESD target board support with enabled modules:
  UART, PMIC, USB/OTG, SD, eMMC, ENET, I2C, 74LV IOX.

  Build target: mx7dsabresd_config

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
2015-09-13 10:11:54 +02:00
Tom Rini
9809ccdd4c Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx 2015-09-02 11:30:46 -04:00
Tom Rini
0ffadab1b9 Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2015-09-02 10:39:28 -04:00
Peng Fan
e7d3b21bb7 imx: mx6slevk: add SPL support
Add SPL boot support for mx6slevk board.
1. Introduce a configuration file mx6slevk_spl_defconfig.
2. i.MX6SL has same DRAM space with i.MX6SX, need to change SPL DRAM SPACE.
3. Include imx6_spl.h and related SPL macro in mx6slevk.h.
4. select SUPPORT_SPL for TARGET_MX6SLEVK.
5. Add SPL board code to do related initialization.

Boot Log:

U-Boot SPL 2015.07-00544-g1594a76 (Aug 17 2015 - 01:56:59)
reading u-boot.img
reading u-boot.img

U-Boot 2015.07-00544-g1594a76 (Aug 17 2015 - 01:56:59 +0000)

CPU:   Freescale i.MX6SL rev1.2 996 MHz (running at 396 MHz)
CPU:   Commercial temperature grade (0C to 95C) at 50C
Reset cause: POR
Board: MX6SLEVK
I2C:   ready
DRAM:  1 GiB
PMIC:  PFUZE100 ID=0x10
MMC:   FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   FEC [PRIME]
Hit any key to stop autoboot:  0

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
2015-09-02 15:34:13 +02:00
Peng Fan
f2ff834365 imx: mx6: ddr init MMDC according to ddr_type
To i.MX6, DDR3 and LPDDR2 is supported, so rename function mx6_dram_cfg
to mx6_ddr3_cfg and the original mx6_dram_cfg function only is a wrapper.
The new reimplemented function mx6_dram_cfg only invokes mx6_ddr3_cfg
when ddr_type is for DDR3. Later we can use ddr_type to initialize
MMDC for LPDDR2.

Initialize ddr_type for different boards which enable SPL.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2015-09-02 15:34:12 +02:00
Peng Fan
0d4cdb5609 imx: mx6ul_14x14_evk add ENET support
Add enet support for mx6ul_14x14_evk board:
1. add pinmux settings
2. implement board_eth_init
3. implement board_phy_config

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
2015-09-02 15:34:11 +02:00
Peng Fan
6d97dc10a8 imx: clock support enet2 anatop clock support
To i.MX6SX/UL, two ethernet interfaces are supported.
Add ENET2 clock support:
1. Introduce a new input parameter "fec_id", only 0 and 1 are allowed.
   To value 1, only i.MX6SX/UL can pass the check.
2. Modify board code who use this api to follow new api prototype.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Nikolaos Pasaloukos <Nikolaos.Pasaloukos@imgtec.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
2015-09-02 15:29:14 +02:00
Zhuoyu Zhang
03c22449c5 arm/ls102xa:add hwconfig setting to support disable unused devices
DEVDISRn registers provides a mechanism for gating clocks of IP blocks
that are not used. Here we implement hwconfig option to allow users
to disable unused peripherals on the board.

For ex. If eSDHC/qDMA/eDMA are unused and with disabled status in dts,
User can enable CONFIG_FSL_DEVICE_DISABLE and set "devdis:esdhc,qdma,edma"
in hwconfig, thus ESDHC controller & eDMA/qDMA will be clock gated to
save more power.

Signed-off-by: Zhuoyu Zhang <Zhuoyu.Zhang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-09-01 21:49:20 -05:00
York Sun
ec93af0dec armv8/ls2085a_emu: Drop DDR3 emulation target
The emulator with DDR3 model was used during model bringup. DDR4
controllers are used with ls2085a. Drop the DDR4 target defconfig
and enable DDR4 in ls2085a_emu_defconfig.

Signed-off-by: York Sun <yorksun@freescale.com>
2015-09-01 21:39:21 -05:00
Claudiu Manoil
ebe4c1e646 ls102xa: etsec: Use proper settings for BE BDs
Replace the DMACTRL[LE] hack with recommended settings
for ETSECDMAMCR to get the same end effect - obtaining
big-endian buffer descriptors and frame data for eTSEC.
The reset / default value for ETSECDMAMCR is preserved,
excepting the BD and FR bits which are cleared to enable
the BE mode in accordance with the H/W specifications.

Fixes: 52d00a8 "ls102xa: etsec: Add etsec support for LS102xA"
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Acked-by: Alison Wang <alison.wang@freescale.com>
Tested-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-09-01 21:39:03 -05:00
Prabhakar Kushwaha
cf7ee6c4e3 armv8: ls2085qds: Add support of X-QSGMII-16PORT riser card
The X-QSGMII-16PORT is a 4xQSGMII/8xSGMII riser card with eighth SerDes
interfaces implemented in PCIe form factor board.
It supports followings
 - Card can operate with up to 4 QSGMII lane simultaneously
 - Card can operate with up to 8 SGMII lane simultaneously

Add support of X-QSGMII-16PORT riser card.
This patch also take care of back-ward compatiblity with old SGMII rise cards
used on LS2085QDS Platform.

Signed-off-by: King Chung Lo@freescale.com <KingChungLo@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-09-01 21:38:46 -05:00
Priyanka Jain
7fb79e6552 armv8/ls2085aqds: enable 32KHz rtc output
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-09-01 21:37:42 -05:00
Shengzhou Liu
47deb4b4a9 powerpc/t1023rdb: change default core frequency to 1200MHz
Per new requirement, change default core frequency
from previous 1400MHz to 1200MHz to save power.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-09-01 20:58:58 -05:00
York Sun
293194c8be powerpc/defconfig: Rename defconfig file for T1040QDS/T1024QDS DDR4 targets
Previously the DDR4 targets were named with _D4. Rename them with
_DDR4 for easy identification.

Signed-off-by: York Sun <yorksun@freescale.com>
2015-09-01 20:42:54 -05:00
Peng Fan
125914d4be fsl: common: pfuze: no use original pfuze code if DM_PMIC
If enable DM PMIC and REGULATOR, we should not use original power
framework. So need to comment out the pfuze code for original power
framework, when CONFIG_DM_PMIC_PFUZE100 defined.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
2015-08-12 11:05:11 +02:00
Alison Wang
8f0c7cbb0d armv7/ls1021a: allow OCRAM access permission as R/W in SPL
On LS1021A Rev2.0, OCRAM's security level needs to be changed to
non-secure access for SD boot. This patch will allow OCRAM
access permission as R/W in SPL.

Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-08-03 12:06:37 -07:00
chenhui zhao
933db81c04 armv7/ls1021atwr: program the regulator for deep sleep
Program the external regulator to switch off voltage in deep sleep.

Signed-off-by: Chenhui Zhao <chenhui.zhao@freescale.com>
Acked-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-08-03 12:06:36 -07:00
Tang Yuantian
99e1bd4241 armv7/ls1021atwr: added deep sleep support in uboot
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Acked-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-08-03 12:06:36 -07:00
Tom Rini
7a1af7a79b Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2015-08-02 07:40:37 -04:00
Peng Fan
f0ff57b0b2 imx: mx6ul_14x14_evk add basic board support
1. Add USDHC, I2C, UART, 74LV, USB, QSPI support.
2. Support SPL
3. CONFIG_MX6UL_14X14_EVK_EMMC_REWORK is introduced, this board default
   supports sd for usdhc2, but can do hardware rework to make usdhc2 support
   emmc.

Boot Log:
U-Boot SPL 2015.07-rc3-00124-g35d727b (Jul 20 2015 - 18:40:59)
reading u-boot.img
reading u-boot.img

U-Boot 2015.07-rc3-00124-g35d727b (Jul 20 2015 - 18:40:59 +0800)

CPU:   Freescale i.MX6UL rev1.0 792 MHz (running at 396 MHz)
CPU:   Commercial temperature grade (0C to 95C)CPU:   Thermal invalid data, fuse: 0x0
 - invalid sensor device
 Reset cause: POR
 Board: MX6UL 14x14 EVK
 I2C:   ready
 DRAM:  512 MiB
 MMC:   FSL_SDHC: 0, FSL_SDHC: 1
 *** Warning - bad CRC, using default environment

 In:    serial
 Out:   serial
 Err:   serial
 Net:   CPU Net Initialization Failed
 No ethernet found.
 Hit any key to stop autoboot:  0

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
2015-08-02 11:05:09 +02:00
Peng Fan
361b715bbf imx: mx6qpsabreauto: Add MX6QP SABREAUTO CPU3 board support
1. Add DDR script for mx6qpsabreauto board.
2. On CPU3 board, enet RGMII tx clock is from internal PLL. Set the GPR5[9]
   and init the enet pll output to 125Mhz.
3. On CPU3 board, SW1ABC=VDDSOC_IN, SW2=VDDARM_IN.

Build target: mx6qpsabreauto_config

Boot Log:
U-Boot 2015.07-rc2-00071-gfd985ff (Jun 29 2015 - 22:10:55 +0800)

CPU:   Freescale i.MX6QP rev1.0 996 MHz (running at 792 MHz)
CPU:   Automotive temperature grade (-40C to 125C) at 34C
Reset cause: POR
Board: MX6Q-Sabreauto revA
I2C:   ready
DRAM:  2 GiB
PMIC:  PFUZE100 ID=0x10
Flash: 32 MiB
NAND:  0 MiB
MMC:   FSL_SDHC: 0
*** Warning - bad CRC, using default environment

No panel detected: default to HDMI
Display: HDMI (1024x768)
In:    serial
Out:   serial
Err:   serial
Net:   FEC [PRIME]
Hit any key to stop autoboot:  0

Note:
In this patch, we still add a new config mx6qpsabreauto_config,
since SPL is not supported now, and IMX_CONFIG is needed at
build time, so add this config. Future, when SPL is converted,
this config can be removed.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Robin Gong <b38343@freescale.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
2015-08-02 10:47:52 +02:00
Peng Fan
e6fc8995d6 imx: mx6sabresd/sabreauto runtime setting fdt_file
Detect the SOC and board variant at runtime and change the dtb name,
but not hardcoding the fdt_file env variable.

Take the following patch as a reference.
Íd58699b157df75f1aa0b363ea9c21add21a0c
"mx6cuboxi: Load the correct 'fdtfile' variable"

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2015-08-02 10:47:05 +02:00
Priyanka Jain
f2af1c37a0 powerpc/T104xRDB: Remove vbank check redundant code
sw variable in checkboard function is storing vbank value
which can only take 3-bit value.
So check of sw value for if greater than 7 is redundant.

Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-07-31 08:56:11 -07:00
Shengzhou Liu
e04dd12bf1 powerpc/t1023rdb: eMMC boot without external SD card
eMMC has no CD and WP pins, it needs to add board-specific
board_mmc_getcd() and board_mmc_getwp() in SPL to support
eMMC boot without external SD card inserted.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-07-31 08:50:19 -07:00
Shengzhou Liu
ff7ea2d18b powerpc/t1023rdb: add support for T1023RDB RevC
Add support for NOR flash and GPIO/I2C switch control on RevC.
- NOR support
- bank0/bank4 switch
- SD/eMMC switch
- board version

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-07-31 08:50:18 -07:00
Aneesh Bansal
73cc2f50eb powerpc/mpc85xx: SECURE BOOT- NAND secure boot target for P5020 and P5040
Secure Boot Target is added for NAND for P5020 and P5040.
The Secure boot target has already been added for P3041 by
enabling CONFIG_SYS_RAMBOOT and configuring CPC as SRAM.

The targets for P5020 and P5040 are added in the same manner.

Signed-off-by: Saksham Jain <saksham@freescale.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-07-31 08:50:18 -07:00
Aneesh Bansal
467a40dfe3 powerpc/mpc85xx: SECURE BOOT- NAND secure boot target for P3041
Secure Boot Target is added for NAND for P3041.
For mpc85xx SoCs, the core begins execution from address 0xFFFFFFFC.
In case of secure boot, this default address maps to Boot ROM.
The Boot ROM code requires that the bootloader(U-boot) must lie
in 0 to 3.5G address space i.e. 0x0 - 0xDFFFFFFF.

In case of NAND Secure Boot, CONFIG_SYS_RAMBOOT is enabled and CPC is
configured as SRAM. U-Boot binary will be located on SRAM configured
at address 0xBFF00000.
In the U-Boot code, TLB entries are created to map the virtual address
0xFFF00000 to physical address 0xBFF00000 of CPC configured as SRAM.

Signed-off-by: Saksham Jain <saksham@freescale.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-07-31 08:50:18 -07:00
Priyanka Jain
fa9ccff835 powerpc/t104x, t102x: Update CPC debug register value in PBI commands
Update PBI command in pbi_cfg files to keep register bit
to default reset value while configuring CPC
as SRAM

Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-07-28 14:41:15 -07:00
Shaohui Xie
f57709ab18 powerpc/t4rdb: fix cpld reset altbank
cpld reset altbank should always reset to bank4 no matter what
current bank is.

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-07-28 14:41:15 -07:00
Ying Zhang
01a6113d2a powerpc/p2020rdb: fix the FDT_ERR_NOTFOUND issue
Because the function ft_board_setup() delete the USB2 device node, it
leads to can't find the device node and hung up.

In fact only P1020RDB needs to delete the USB2 node, this patch fixes
this issue.

Signed-off-by: Ying Zhang <b40530@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-07-28 14:41:15 -07:00
gaurav rana
e622d9ed3b powerpc/T104xD4: Add Secure boot support for T104xD4RDB platforms
defconfig files are added and SFP version for these platforms
is updated.

Signed-off-by: Gaurav Rana <gaurav.rana@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-07-28 14:41:14 -07:00
Priyanka Jain
4b6067ae9d powerpc/T104xD4RDB: Add T104xD4RDB boards support
T1040D4RDB is a Freescale reference board that hosts the T1040 SoC.
    T1040D4RDB is re-designed T1040RDB board with following changes :
    - Support of DDR4 memory
    - Support of 0x66 serdes protocol which can support following interfaces
        - 2 RGMII's on DTSEC4, DTSEC5
        - 1 SGMII on DTSEC3
    - Support of QE-TDM

    Similarily T1042D4RDB is a Freescale reference board that hosts the T1040
    SoC. T1042D4RDB is re-designed T1042RDB board with following changes :
    - Support of DDR4 memory
    - Support for 0x86 serdes protocol which can support following interfaces
        - 2 RGMII's on DTSEC4, DTSEC5
        - 3 SGMII on DTSEC1, DTSEC2 & DTSEC3
    - Support of DIU

Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-07-28 14:40:57 -07:00
Fabio Estevam
42acd1874f mx6sxsabresd: Use 'int' for return values
The variable 'ret' is used to store the value returned by pfuze_mode_init(),
so it should be of type 'int' instead of 'unsigned int' in order to
correctly handle negative numbers.

Fix the variable type.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2015-07-26 12:12:04 +02:00
Fabio Estevam
e4b984d75e mx6sabresd: Use 'int' for return values
The variable 'ret' is used to store the value returned by pfuze_mode_init(),
so it should of type 'int' instead of 'unsigned int' in order to correctly
handle negative numbers.

Fix the variable type.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2015-07-26 12:12:04 +02:00
Haikun.Wang@freescale.com
5989df7e2c armv8/ls2085ardb: DSPI pin muxing configure through QIXIS CPLD
DSPI has pin muxing with SDHC and other IPs, this patch check the
value of RCW SPI_PCS_BASE and SPI_BASE_BASE fields, it also check
the "hwconfig" variable. If those pins are configured to DSPI and
"hwconfig" enable DSPI, set the BRDCFG5 of QIXIS CPLD to configure
the routing to on-board SPI memory. Otherwise will configure to SDHC.
DSPI is enabled in "hwconfig" by appending "dspi", eg.
setenv hwconfig "$hwconfig;dspi"

Signed-off-by: Haikun Wang <Haikun.Wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-07-20 11:44:39 -07:00
Haikun Wang
e71a980a4d armv8/ls2085aqds: DSPI pin muxing configure through QIXIS
DSPI has pin muxing with SDHC and other IPs, this patch check the
value of RCW SPI_PCS_BASE and SPI_BASE_BASE fields, it also check
the "hwconfig" variable. If those pins are configured to DSPI and
"hwconfig" enable DSPI, set the BRDCFG5 of QIXIS FPGA to configure
the routing to on-board SPI memory. Otherwise will configure to SDHC.
DSPI is enabled in "hwconfig" by appending "dspi", eg.
setenv hwconfig "$hwconfig;dspi"

Signed-off-by: Haikun Wang <haikun.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-07-20 11:44:39 -07:00
Alison Wang
88c857df8c arm/ls102xa: Add little-endian mode support for audio IPs
As SCFG_ENDIANCR register is added to choose little-endian or big-endian
for audio IPs on Rev2.0 silion, little-endian mode is selected.

Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-07-20 11:44:38 -07:00
Prabhakar Kushwaha
9527931507 board/ls2085rdb: Export functions for standalone AQ FW load apps
Export functions required by Aquntia PHY firmware load application.
functions are memset, strcpy, mdelay, mdio_get_current_dev,
phy_find_by_mask, mdio_phydev_for_ethname and miiphy_set_current_dev

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-07-20 11:44:37 -07:00
Prabhakar Kushwaha
5c05508971 armv8/fsl-lsch3: Support 256M mem split for MC & dbg-srvr
The agreed split of the top of memory is 256M for debug server and 256M
 for MC. This patch implements the split.

 In addition, the MC mem must be 512MB aligned, so the amount of memory
 to hide must be 512MB to achieve that alignment.

Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-07-20 11:44:36 -07:00
Bhupesh Sharma
a2dc818f21 armv8/ls2085a: Expose all DDR region(s) to Linux
This patch allows u-boot to expose the complete DDR region(s) to Linux
(after subtracting the memory hidden via MEM_TOP_HIDE mechanism).

This allows the u-boot to support the 48-bit VA support provided by
ARM64 Linux in flavors 3.18 and above, by passing the appropriate
'memory' DTS nodes.

Signed-off-by: Bhupesh Sharma <bhupesh.sharma at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-07-20 11:44:35 -07:00
York Sun
fc7b3855e1 armv8/ls2085ardb: Fix SPD address error on early boards
Board rev C and earlier has duplicated SPD address on 2nd DDR
controller slots. It is fixed on rev D and later. SPD addresses
need to be updated accordingly.

Signed-off-by: York Sun <yorksun at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
2015-07-20 11:44:35 -07:00
Prabhakar Kushwaha
ff1b8e3f55 armv8/ls2085a: Avoid hard-coding for board name print
LS2085A supports 6 personalities i.e. LS2045AE, LS2045A, LS2080AE,
LS2080A, LS2085AE and LS2085A personlities.

Instead of hard-coding, board name should change as per selected
personality.

Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-07-20 11:44:35 -07:00
Prabhakar Kushwaha
27df54b163 armv8/ls2085RDB: Update board version print logic
As per updated board document, no need to substract 1 from arch[BRD]
bit field. Default value + 'A' represents the board revision.

So update board version print logic to reflect the same.

Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-07-20 11:44:34 -07:00
Jaiprakash Singh
b8baf460ee board/fsl/common: Fix eeprom system version endianness
SYSTEM ID EPPROM always store SYSTEM version info in big endian format.
SoC with ARM or PowerPC core should read/write version info from eeprom
in BIG endian format.

So use cpu-specific APIs to read SYSTEM version.

Signed-off-by: Jaiprakash Singh <b44839 at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-07-20 11:44:34 -07:00
Prabhakar Kushwaha
d7b76e89ed armv8/ls2085qds: Update SFP TX bit as "0" to enable XFI
FPGA BRDCFG9[SFP_TX] should be clear in order to enable XFI ports.

Signed-off-by: Dai Haruki <Dai.Haruki at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-07-20 11:44:34 -07:00
Prabhakar Kushwaha
94540c5604 armv8/ls2085aqds: Add support of SerDes protocol 0x49
SerDes Protocol 0x49 enables 4 SGMII, PEX4, SATA1 and SATA2.

Add support of 0x49 SerDes protocol to enable 4SGMII on slot4 of
ls2085aqds platform.

Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-07-20 11:44:33 -07:00
Yangbo Lu
5a4d744c90 armv8/ls2085ardb: add hwconfig setting for eSDHC
Add hwconfig setting for eSDHC since it shares some pins with other
IP block.

Signed-off-by: Yangbo Lu <yangbo.lu at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-07-20 11:44:33 -07:00
Prabhakar Kushwaha
3484d95307 armv8/ls2085ardb: Add eth & phy firmware loading support
Add support for board eth initialization and support for loading phy
firmware. PHY firmware needs to be loaded from board_eth_init() because
all the MACs are not initialized by ldpaa_eth driver.

Signed-off-by: pankaj chauhan <pankaj.chauhan at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-07-20 11:44:33 -07:00
Tom Rini
9bea236b34 Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2015-05-26 10:38:01 -04:00
York Sun
a88cc3bd90 arm/ls1021a: Remove ccsr_ddr from immap_ls102xa.h
ccsr_ddr structure is already defined in fsl_immap.h. Remove
this duplicated define. Move fixed timing into ls1021atwr.h.

Signed-off-by: York Sun <yorksun@freescale.com>
CC: Alison Wang <alison.wang@freescale.com>
Acked-by: Alison Wang <alison.wang@freescale.com>
2015-05-20 10:34:09 -07:00
Peng Fan
3fd10f3e25 pmic: pfuze100 fix typo
Change PUZE_100_SW1ABCONF to PFUZE100_SW1ABCONF

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
2015-05-19 15:13:38 +02:00
Jan Kiszka
104d6fb6cd ARM: Clean up CONFIG_ARMV7_NONSEC/VIRT/PSCI conditions
CONFIG_ARMV7_VIRT depends on CONFIG_ARMV7_NONSEC, thus doesn't need to
be taken into account additionally. CONFIG_ARMV7_PSCI is only set on
boards that support CONFIG_ARMV7_NONSEC, and it only works on those.

CC: Tang Yuantian <Yuantian.Tang@freescale.com>
CC: York Sun <yorksun@freescale.com>
CC: Steve Rae <srae@broadcom.com>
CC: Andre Przywara <andre.przywara@linaro.org>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Tested-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2015-05-13 09:24:13 -07:00
Shaohui Xie
38289c6945 powerpc/t4240qds: Update RCW, defconfig and maintainer
1. board/freescale/t4qds/t4_rcw.cfg
1.8GHz support is requested as default frequency, so update the rcw.

2. remove un-used configs
configs/T4160QDS_SPIFLASH_defconfig
configs/T4240QDS_SPIFLASH_defconfig
SPI boot is not available on T4QDS, so the configs should be removed.

3. board/freescale/t4qds/MAINTAINERS
Updated MAINTAINERS accordingly.

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
[York Sun: revise subject]
Reviewed-by: York Sun <yorksun@freescale.com>
2015-05-04 09:26:01 -07:00
Shengzhou Liu
c0379b19e2 t2080rdb/rcw: update ddr frequency from 1600MT/s to 1867MT/s
T2080RDB RevC uses new SODIMM 1867MT/s instead of previous 1600MT/s.
So update RCW to support new DDR frequency 1867MT/s by default.
Reserve the old 1600MT/s in comment for users in needed.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-05-04 09:25:53 -07:00
Yangbo Lu
5a8dbdc6b4 mmc: fsl_esdhc: Add adapter card type identification support
Add adapter card type identification support by reading
FPGA STAT_PRES1 register SDHC Card ID[0:2] bits. To use this function,
define CONFIG_FSL_ESDHC_ADAPTER_IDENT.

Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
[York Sun: resolve conflicts in README.fsl-esdhc]
Reviewed-by: York Sun <yorksun@freescale.com>
2015-05-04 09:25:19 -07:00
Shengzhou Liu
fd3a78a538 board/t2080rdb: reset cs4315 phy
CS4315 PHY doesn't support phy-reset by software, it
needs to reset it by hardware via CPLD control.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-05-04 09:25:12 -07:00
Tang Yuantian
1a56fcea9f fsl/deepsleep: avoid the DDR restore from being optimized out
Function dp_ddr_restore is to restore the first 128-byte space
of DDR. However those codes may be optimized out by compiler
since the destination address is at 0x0. In order to avoid
compiler optimization, we restore the space from high address,
which is not at 0x0, to low address.

Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-05-04 09:25:06 -07:00
Shengzhou Liu
ea753267d5 board/t102x: use fdt_setprop_string instead of fdt_setprop
Use fdt_setprop_string instead of fdt_setprop to fix string length.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-05-04 09:24:50 -07:00
Shengzhou Liu
e8a7f1c32b powerpc/t1023rdb: Add T1023 RDB board support
T1023RDB is a Freescale Reference Design Board that hosts the T1023 SoC.

T1023RDB board Overview
-----------------------
- T1023 SoC integrating two 64-bit e5500 cores up to 1.4GHz
- CoreNet fabric supporting coherent and noncoherent transactions with
  prioritization and bandwidth allocation
- Memory: 2GB Micron MT40A512M8HX unbuffered 32-bit fixed DDR4 without ECC
- Accelerator: DPAA components consist of FMan, BMan, QMan, DCE and SEC
- Ethernet interfaces:
  - one 1G RGMII port on-board(RTL8211F PHY)
  - one 1G SGMII port on-board(RTL8211F PHY)
  - one 2.5G SGMII port on-board(AQR105 PHY)
- PCIe: Two Mini-PCIe connectors on-board.
- SerDes: 4 lanes up to 10.3125GHz
- NOR:  128MB S29GL01GS110TFIV10 Spansion NOR Flash
- NAND: 512MB S34MS04G200BFI000 Spansion NAND Flash
- eSPI: 64MB S25FL512SAGMFI010 Spansion SPI flash.
- USB: one Type-A USB 2.0 port with internal PHY
- eSDHC: support SD/MMC card and eMMC on-board
- 256Kbit M24256 I2C EEPROM
- RTC: Real-time clock DS1339 on I2C bus
- UART: one serial port on-board with RJ45 connector
- Debugging: JTAG/COP for T1023 debugging

As well updated T1024RDB to add T1023RDB.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[York Sun: fix defconfig files]
Reviewed-by: York Sun <yorksun@freescale.com>
2015-05-04 09:24:31 -07:00
Chunhe Lan
373762c34c powerpc/t4rdb: Add SD boot support for T4240RDB board
This patch adds SD boot support for T4240RDB board. SPL
framework is used. PBL initializes the internal RAM and
copies SPL to it. Then SPL initializes DDR using SPD and
copies u-boot from SD card to DDR, finally SPL transfers
control to u-boot.

Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
[York Sun: Fix T4240RDB_SDCARD_defcofig]
Reviewed-by: York Sun <yorksun@freescale.com>
2015-05-04 09:24:04 -07:00
York Sun
7fc63cca61 mpc85xx/T4240EMU: Remove T4240EMU board
T4240 SoC has been available for a long time. Emulator support
is no longer needed.

Signed-off-by: York Sun <yorksun@freescale.com>
2015-05-04 09:23:46 -07:00
Tom Rini
e536ab8849 Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2015-04-28 12:15:13 -04:00
Tom Rini
3f6dcdb9cd Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriq 2015-04-24 13:43:24 -04:00
Scott Wood
32eda7cc94 armv8/ls2085ardb: Enable NAND SPL support
Enable NAND boot support using SPL framework. To boot from
NAND, either use DIP switches on board, or "qixis_reset nand"
command. Details of forming NAND image can be found in README.

Signed-off-by: Scott Wood <scottwood@freescale.com>
[York Sun: Remove +S from defconfig after commit 252ed872]
Signed-off-by: York Sun <yorksun@freescale.com>
2015-04-23 16:46:51 -07:00
Scott Wood
548cf52fd5 freescale/qixis: Add support for booting from NAND
Use "qixis_reset nand" to reset the board to boot from NAND.

Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
2015-04-23 16:46:51 -07:00
Scott Wood
b2d5ac5985 armv8/ls2085aqds: NAND boot support
This adds NAND boot support for LS2085AQDS, using SPL framework.
Details of forming NAND image can be found in README.

Signed-off-by: Scott Wood <scottwood@freescale.com>
[York Sun: Remove +S from defconfig after commit 252ed872]
Signed-off-by: York Sun <yorksun@freescale.com>
2015-04-23 16:46:50 -07:00
Jaiprakash Singh
39b0bbbb23 driver/ifc: Add 64KB page support
IFC has two register pages.Till IFC version 1.4 each
register page is 4KB each.But IFC ver 2.0 register page
size is 64KB each.IFC regiters structure is break into
two viz FCM and RUNTIME.FCM(Flash control machine) registers
are defined in PAGE0 and controls IFC generic functionality.
RUNTIME registers are defined in PAGE1 and controls NAND and
GPCM funcinality.

FCM and RUNTIME structures defination is common for IFC
version 1.4 and 2.0.

Signed-off-by: Jaiprakash Singh <b44839@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
2015-04-23 16:46:50 -07:00
Prabhakar Kushwaha
e60476a01e board/ls2085qds: Add support ethernet
Add support of ethernet:
 - eth.c: mapping lane to slot for (0x2A, 0x07)
 - ls2085a.c: To enable/disable dpmac and get link type

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
2015-04-23 16:46:50 -07:00
Stefan Agner
8b4f9afac0 ARM: vf610: Enable external 32KHz oscillator
Enable the SCSC (Slow Clock Source Controller) and select the external
32KHz oscillator. This improves the accuracy of the RTC.

Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
2015-04-23 14:56:08 -04:00
Sanchayan Maity
c7ea243cc0 ARM: vf610: Move DDR3 initialization to imx-common
In order to avoid code duplication, move the DDR3 initialization to the
common place under imx-common. Currently ROW_DIFF and COL_DIFF can be
chosen from the board file. The JEDEC timings are specified using a
common ddr3_jedec_timings structure.

Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
2015-04-23 14:56:08 -04:00
angelo@sysam.it
5296cb1d99 m68k: add architecture-specific u-boot.lds
Add architecture-specific u-boot.lds and remove all board-specific
u-boot.lds.

All the .text customization that was board-specific have been
moved inside the related include/configs, inside a
LDS_BOARD_TEXT define.

Signed-off-by: Angelo Dureghello <angelo@sysam.it>
2015-04-23 14:56:07 -04:00
York Sun
e2b65ea975 armv8/ls2085ardb: Add support of LS2085ARDB platform
The LS2085ARDB is a evaluation platform that supports LS2085A
family SoCs. This patch add sbasic support for the platform.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2015-04-23 08:55:58 -07:00
York Sun
7288c2c2b0 armv8/ls2085aqds: Add support of LS2085AQDS platform
The LS2085AQDS is an evaluatoin platform that supports the LS2085A
family SoCs. This patch add basic support of the platform.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
2015-04-23 08:55:58 -07:00
Scott Wood
b991b981e0 fsl-lsch3: Introduce place for common early SoC init
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
2015-04-23 08:55:56 -07:00
pankaj chauhan
05d2e21be5 armv8/ls2085a: Add support for reset request
Add support for reset_cpu() by asserting RESET_REQ_B.

Signed-off-by: pankaj chauhan <pankaj.chauhan@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
2015-04-23 08:55:55 -07:00
York Sun
207774b213 armv8/ls2085a: Fix generic timer clock source
The timer clock is system clock divided by 4, not fixed 12MHz.
This is common to the SoC, not board specific. Primary core is
fixed when u-boot still runs in board_f. Secondary cores are
fixed by reading a variable set by u-boot.

Signed-off-by: York Sun <yorksun@freescale.com>
CC: Mark Rutland <mark.rutland@arm.com>
2015-04-23 08:55:55 -07:00
Fabio Estevam
cba4c255fc mx6sabresd: Remove uneeded ifdef
RTT_NOM_120OHM is not defined, so remove its ifdef.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2015-04-22 16:02:46 +02:00
Fabio Estevam
407be42d73 mx6sabresd: Fix SPL memory description
mx6sabresd has four MT41K128M16JT-125 chips. Each memory has 16-bit bus
and 2GiB, so fix the width and density fields accordingly.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2015-04-22 16:02:46 +02:00
gaurav rana
1c29ad7bc0 iMX: Fix compilation error when enabling SECURE_BOOT
Move the compilation of file fsl_validate.c in MACRO CONFIG_CMD_ESBC_VALIDATE.
This file should be compiled only when the above MACRO is defined

This caused a break in compilation of iMX platforms when compiling for SECURE_BOOT

Signed-off-by: Gaurav Rana <gaurav.rana@freescale.com>
2015-04-22 16:02:46 +02:00
Prabhakar Kushwaha
a2a55e518f driver/fsl-mc: Add support of MC Flibs
Freescale's Layerscape Management Complex (MC) provide support various
objects like DPRC, DPNI, DPBP and DPIO.
Where:
	DPRC: Place holdes for other MC objectes like DPNI, DPBP, DPIO
	DPBP: Management of buffer pool
	DPIO: Used for used to QBMan portal
	DPNI: Represents standard network interface

These objects are used for DPAA ethernet drivers.

Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: Lijun Pan <Lijun.Pan@freescale.com>
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com>
Signed-off-by: Geoff Thorpe <Geoff.Thorpe@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Cristian Sovaiala <cristian.sovaiala@freescale.com>
Signed-off-by: pankaj chauhan <pankaj.chauhan@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-04-21 10:27:35 -07:00
Bhupesh Sharma
422cb08acb armv8/fsl-lsch3: Add Freescale Debug Server driver
The Debug Server driver is responsible for loading the Debug
server FW on the Service Processor (Cortex-A5 core) on LS2085A like
SoCs and then polling for the successful initialization of the same.
TOP MEM HIDE is adjusted to ensure the space required by Debug Server
FW is accounted for. MC uses the DDR area which is calculated as:

MC DDR region start = Top of DDR - area reserved by Debug Server FW

Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-04-21 10:26:29 -07:00
Zhao Qiang
1fb5ff9ae7 QE/DeepSleep: add QE deepsleep support for arm
Muram will power off during deepsleep, and the microcode of qe
in muram will be lost, it should be reload when resume.

Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-04-21 10:19:20 -07:00
Zhao Qiang
ae42eb035e QE/DeepSleep: add QE deepsleep support for mpc85xx
Muram will power off during deepsleep, and the microcode of qe
in muram will be lost, it should be reload when resume.

Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-04-21 10:19:19 -07:00
Minghuan Lian
d42bd3453a pci/layerscape: remove unnecessary pcie_layerscape.h
The patch uses the common function name ft_pci_setup to replace
ft_pcie_setup, then removes unnecessary pcie_layerscape.h because
all the functions have been declared in common.h.

Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-04-21 10:19:19 -07:00
gaurav rana
98cb0efde8 Add bootscript support to esbc_validate.
1. Default environment will be used for secure boot flow
 which can't be edited or saved.
2. Command for secure boot is predefined in the default
 environment which will run on autoboot (and autoboot is
 the only option allowed in case of secure boot) and it
 looks like this:
 #define CONFIG_SECBOOT \
 "setenv bs_hdraddr 0xe8e00000;"                 \
 "esbc_validate $bs_hdraddr;"                    \
 "source $img_addr;"                             \
 "esbc_halt;"
 #endif
3. Boot Script can contain esbc_validate commands and bootm command.
 Uboot source command used in default secure boot command will
 run the bootscript.
4. Command esbc_halt added to ensure either bootm executes
 after validation of images or core should just spin.

Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Gaurav Rana <gaurav.rana@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-04-21 10:19:19 -07:00
Alison Wang
997c67d98b ls102xa: ddr4: Use LPUART as console output to verify DCU driver
On QDS board with DDR4 DIMM, LPUART is used as console
output to verify DCU driver. This patch adds
ls1021aqds_ddr4_nor_lpuart_defconfig for this support.

Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-04-21 10:19:19 -07:00
Yao Yuan
09227dd9df ls1021atwr: add hwconfig setting to do pin mux
Freescale LS1021ATWR share some pins. Hwconfig option is used to
allows users to choose the pin functions.

Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
[York Sun: revised commit message]
Reviewed-by: York Sun <yorksun@freescale.com>
2015-04-21 10:19:19 -07:00
Alison Wang
036f3f3379 arm/ls102xa:Add support of conditional workaround implementation as per SoC ver
For LS102xA, some workarounds are only used in VER1.0, so silicon
version detection are added for QDS and TWR boards.

Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-04-21 10:19:19 -07:00
Shengzhou Liu
4913229ed6 powerpc/t2080rdb: update ddr to support 1866MT/s
Support SODIMM D3XP12081XL10AA 1866MT/s on T2080RDB.
Enable CONFIG_CMD_MEMTEST as well.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-04-20 10:15:29 -07:00
Ying Zhang
e5abb92c0b board/t208xrdb: VID support
The fuse status register provides the values from on-chip
voltage ID efuses programmed at the factory.
These values define the voltage requirements for
the chip. u-boot reads FUSESR and translates the values
into the appropriate commands to set the voltage output
value of an external voltage regulator.

Signed-off-by: Ying Zhang <b40530@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-04-20 10:15:29 -07:00
Tom Rini
1d2f74690c Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2015-04-13 10:52:46 -04:00
Fabio Estevam
a80a65e997 mx53loco: Disable printing cpuinfo
Since commit 32df39c741 ("mx5: fix get_reset_cause") we have the following
boot messages on a mx53qsb:

U-Boot 2015.04-rc5-00029-gd68df02 (Apr 06 2015 - 11:15:39)

CPU:   Freescale i.MX53 rev2.1 at 800 MHz
Reset cause: POR
Board: MX53 LOCO
I2C:   ready
DRAM:  1 GiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 1
In:    serial
Out:   serial
Err:   serial
CPU:   Freescale i.MX53 rev2.1 at 1000 MHz
Reset cause: unknown reset
Net:   FEC [PRIME]

The CPU and Reset cause lines appear twice.

Initially mx53 boots at 800MHz, then at a later point the PMIC is configured via
I2C to raise the CPU voltage so that it can run at 1GHz.

To avoid such misleading double printings, disable printing cpu info for now.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Jason Liu <r64343@freescale.com>
2015-04-08 10:45:50 +02:00
angelo@sysam.it
944ab340b6 m68k: fix 3 broken boards
Fix eb_cpu5282 and eb_cpu5282_internal unresolved external error.
These boards have video but don't need any ppc related
video_setmem().

Fix M53017EVB moving away embedded env to a different offset,
as in M52277EVB.

Signed-off-by: Angelo Dureghello <angelo@sysam.it>
2015-03-28 12:07:46 -04:00
Tom Rini
1c6f6a6ef9 Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx 2015-03-05 20:50:30 -05:00
gaurav rana
e04916a721 SECURE_BOOT : enable esbc_validate command for powerpc and arm platforms.
esbc_validate command uses various IP Blocks: Security Monitor, CAAM block
and SFP registers. Hence the respective CONFIG's are enabled.

Apart from these CONFIG_SHA_PROG_HW_ACCEL and CONFIG_RSA are also enabled.

Signed-off-by: Gaurav Rana <gaurav.rana@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-03-05 12:04:59 -08:00
gaurav rana
47151e4bcc SECURE BOOT: Add command for validation of images
1. esbc_validate command is meant for validating header and
   signature of images (Boot Script and ESBC uboot client).
   SHA-256 and RSA operations are performed using SEC block in HW.
   This command works on both PBL based and Non PBL based Freescale
   platforms.
   Command usage:
   esbc_validate img_hdr_addr [pub_key_hash]
2. ESBC uboot client can be linux. Additionally, rootfs and device
   tree blob can also be signed.
3. In the event of header or signature failure in validation,
   ITS and ITF bits determine further course of action.
4. In case of soft failure, appropriate error is dumped on console.
5. In case of hard failure, SoC is issued RESET REQUEST after
   dumping error on the console.
6. KEY REVOCATION Feature:
   QorIQ platforms like B4/T4 have support of srk key table and key
   revocation in ISBC code in Silicon.
   The srk key table allows the user to have a key table with multiple
   keys and revoke any key in case of particular key gets compromised.
   In case the ISBC code uses the key revocation and srk key table to
   verify the u-boot code, the subsequent chain of trust should also
   use the same.
6. ISBC KEY EXTENSION Feature:
   This feature allows large number of keys to be used for esbc validation
   of images. A set of public keys is being signed and validated by ISBC
   which can be further used for esbc validation of images.

Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Gaurav Rana <gaurav.rana@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-03-05 12:04:59 -08:00
vijay rai
2372e283e5 mpc85xx/t104xrdb : remove raw timing parameter
This board uses DDR DIMM. Reading SPD provides more flexibility.
Raw timing parameter code should be removed after debugging.

Signed-off-by: Vijay Rai <vijay.rai@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-03-05 12:03:22 -08:00
Tom Rini
02ebe6f702 Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2015-03-05 07:22:18 -05:00
Stefano Babic
32df39c741 mx5: fix get_reset_cause
commit d9f43c8f5c sets
get_reset_cause() as static, but this conflicts with mx5
where its prototype is in sys_proto.h.

Drop it from sys_proto.h and drop print_cpuinfo from mx53_loco,
factorizing the call for this board.

Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Jason Liu <jason.hui@linaro.org>
2015-03-05 10:29:27 +01:00
Sinan Akman
19e5118d1c mpc837xerdb: "fix Calling __hwconfig without a buffer" warning
Signed-off-by: Sinan Akman <sinan@writeme.com>
2015-03-02 15:11:36 -05:00
Fabio Estevam
16edd347f0 mx6slevk: Provide a proper pad configuration for OTG1_ID pin
Pass the same pad configuration as done in the kernel so that OTG1_ID pin can
properly work in device mode.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2015-03-02 11:55:26 +01:00