The internal SRAM of Freescale's IFC NAND machine is of 64K and controller's
Address Mask Registers is initialised with the same.
So Update TLB and LAW size of NAND flash accordingly.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Static variables should be defined in C files, not header files, because
otherwise every C file that #includes the header file will generate a
duplicate of the variables. Since the vsc3316_xxx[] arrays are only
used by t4qds.c anyway, just put the variables there.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Lanes mux currently is configured in eth.c when initializing FMAN ethernet
ports, but SRIO and PCIe also need lanes mux, so we move the lanes mux to
p2041rdb.c which implements a board-specific initialization and will be
called at early stage.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The following features are supported:
* 128 MB DDR1 SDRAM
* DUART
* SD/MMC Card Socket
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Add support for the MMC attached to SSP1.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Some MXS based boards do not implement the card-detect signal. Allow
user to specify alternate card-detect implementation.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
The memory power supply on MX23 didn't pump out enough juice into
the DRAM chip, thus caused occasional memory corruption. Fix this.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
The '#' used as comments in the files cause the preprocessor
trouble, so change to /* */.
The mkimage command which uses this preprocessor output
was moved to arch/arm/imx-common/Makefile
.gitignore was updated to ignore .cfgtmp files.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
This patch adds support for MX23-based Olinuxino board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Sort nodes in dts files according the the following rules:
1) Any nodes that already exist in any /include/d file, in the order
they appear in the /include/d file.
2) Any nodes with a reg property, in order of their address.
3) Any nodes without a reg property, alphabetically by node name.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
IRDA is a synonym for UARTB in tegra pinmux, remove all usage of this
synonym and replace with UARTB to disambiguate.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Note that T30 does not have a separate/different DVC (power I2C)
controller like T20 - all 5 I2C controllers are identical, but
DVC_I2C is still used to designate the controller intended for
power control (PWR_I2C in the schematics). On Cardhu, it's used
to access the PMU and EEPROM, as well as the audio codec, temp
sensor, and fuel gauge devices from the OS.
Signed-off-by: Tom Warren <twarren@nvidia.com>
This build is stripped down. It boots to the command prompt.
GPIO is the only peripheral supported. Others TBD.
include/configs/tegra-common.h now holds common config options
for Tegra SoCs.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
This patch adds basic Tegra30 (T30) build support - no specific
board is targeted.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
These are stripped down for bringup, They'll be filled out later
to match-up with the kernel DT contents, and/or as devices are
brought up (mmc, usb, spi, etc.).
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
This adds LCD panel descriptions to the device tree of PAZ00 and
enables LCD support in the configuration.
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Boards may require a different pinmux setup for DISPALY than the default one.
Add a way to call into board specific code to set this up.
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The TEC ships with a 7" LCD panel that provides a resolution of 800x480
pixels. Add a corresponding panel description to the device tree and
enable LCD support in the configuration.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The Medcom-Wide has a 15" LCD panel with a resolution of 1366x768
pixels. Add a corresponding panel description to the device tree and
enable LCD support in the configuration.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
By now U-Boot supports Qemu MIPS for little and big endian
as well as 32 bit and 64 bit. Update and fix the example usage
in the README to reflect this.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Using the example command from the README file does
not work as expected. qemu shows a text similar to
the one below and it hangs.
$ qemu-system-mips -L . -nographic
Could not open option rom 'pxe-pcnet.rom': No such file or directory
qemu-system-mips: pci_add_option_rom: failed to find romfile "vgabios-cirrus.bin"
qemu: terminating on signal 15 from pid 19726
This happens because qemu emulates a Malta board by
default if the machine type is not defined explicitely
on the command line.
For a working test, the '-M mips' switch is required:
$ qemu-system-mips -M mips -L . -nographic
Could not open option rom 'vgabios.bin': No such file or directory
U-Boot 2013.01-rc2-00132-g1e8e648-dirty (Jan 08 2013 - 09:06:42)
Board: Qemu -M mips CPU: 24Kf proc_id=0x19300
DRAM: 128 MiB
## Unknown flash on Bank 1 - Size = 0x00000000 = 0 MB
Flash: 0 Bytes
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: NE2000
Hit any key to stop autoboot: 0
qemu-mips #
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Cc: Vlad Lungu <vlad.lungu@windriver.com>
The 'Limitations & comments' section refers to the
'-m mips' switch which is not valid. The '-m' switch
can be used for setting the virtual RAM size:
$qemu-system-mips --help | grep '^-m '
-m megs set virtual RAM size to megs MB [default=128]
$
The correct switch for specifying the machine type is '-M'.
Fix the text to refer to that.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Cc: Vlad Lungu <vlad.lungu@windriver.com>
Add DVI output support and make it the default video output.
Currently the CLAA WVGA panel is supported, but this panel has to be purchased
separately, so using the DVI output as the default would allow more people to
try the splash screen feature on a mx51evk.
If someone still wants to use the CLAA WVGA, just set the panel variable as:
set panel claa
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
u-boot compilation fails for smdk5250 when we deselect CONFIG_LCD
from the main config file.
Following error was observed:
drivers/video/libvideo.o: In function `exynos_lcd_init':
/home/ajay/u-boot-samsung/drivers/video/exynos_fb.c:68: undefined reference to `lcd_set_flush_dcache'
This is because exynos video drivers have dependency on CONFIG_LCD.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add panel_info structure required by LCD driver
and DP panel platdata for SMDK5250.
Add GPIO configuration for LCD.
Enable FIMD and DP support on SMDK5250.
DP Panel size: 2560x1600.
We use 16BPP resolution to get LCD console.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Simon Glass <sjg@chomium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add support for the Seiko 4.3'' WVGA panel on mx53loco.
By default, the CLAA WVGA panel is selected.
In order to support the Seiko panel, the enviroment variable 'panel' must be
set to 'seiko'.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Instead of using the serverip we get from the DHCP server, implicitly use
the broadcast address, which is automatically set when no ncip environment
variable is set. That way it isn't necessary to use a special DHCP
configuration to set the netconsole peer.
Signed-off-by: Michael Walle <michael@walle.cc>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
This saves stack and code memory for local copy, and
consumes initialized data memory. For 22 of the 29
kirkwood-based boards, this results in a global saving
of about 30 bytes. For 7 of them, it results in an
increase of 6 to 14 bytes.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
This patch removes 2 small portions of board specific code that are
duplicated with common ARM code and thus unnecessary. These 2 portions
of code concern the mach id that is given by u-boot to the Linux kernel
to identify the system's MACH.
The first one was the possibility to change the MACH thanks to the
'mach_id' enviroment variable. This is possible thanks to the 'machid'
env variable (see arch/arm/lib/bootm.c:boot_jump_linux()).
The seconde one is the setting of the bi_arch_number. This is already
done in arch/arm/lib/board.c:board_init_f() since km_arm.h does #define
CONFIG_MACH_TYPE.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
Acked-by: Prafulla Wadaskar <Prafulla@marvell.com>
On kmcoge5un we faced some serious problems with the memory during
temperature tests. Reason was that we overwrite some registers for
memory settings which have to leave untouched. These where registers
0x20148 , 0x2014c and 0x20154.
So writing these registers is prohibited and this patch removes them
from all km related config files. Even if the problem was only
seen on kmcoge5un.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
This patch adds aliases for SPI.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Make the error handling more robust.
Check if each one of the PMIC writes fail and if they do, just return
immediately.
Also, print the cause for the failures.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
commit c73368150 (pmic: Extend PMIC framework to support multiple instances
of PMIC devices) introduced an extra 'retval' variable, but this is not
necessary since we have already the variable 'ret' in place.
So use 'ret' to store the return values from the pmic related calls and remove
'retval'.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
The on-board number of available usdhc devices is something board
specific. The patch moves CONFIG_SYS_FSL_USDHC_NUM out of
mx6qsabre_common.h and adds usdhc2 and usdhc4 support for mx6qsabresd
board.
To keep the default mmc device for environment same as before (usdhc3),
it moves CONFIG_SYS_MMC_ENV_DEV out of mx6qsabre_common.h and changes
it to 1 for mx6qsabresd.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Support for a new command (defined at envs) - spl_export generates
the ATAGS image necessary for fast boot. Afterwards, it is stored
at ext4 partition.
Generated image format:
CRC [4B] SIZE [4B] PAYLOAD(ATAGS/DT) [SIZE]
Remarks:
- CRC is calculated only for PAYLOAD
- SIZE is the size of PAYLOAD
It is important to adjust ${splsize} when large image is generated.
It is defined as hex, since ext4 related commands expect it.
The ${spladdr} environment variable corresponds to
CONFIG_SYS_SPL_ARGS_ADDR
Additionally definitions for DFU have been refactored and support for
EFI has been added as well.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Since commit c733681 (pmic: Extend PMIC framework to support multiple instances
of PMIC devices) mx53loco fails to allocate the memory for PMIC:
U-Boot 2013.01-rc2-dirty (Dec 20 2012 - 15:55:01)
Board: MX53 LOCO
I2C: ready
DRAM: 1 GiB
pmic_alloc: No available memory for allocation!
pmic_init: POWER allocation error!
CPU: Freescale i.MX53 family rev2.0 at 800 MHz
Reset cause: POR
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Calling the PMIC related functions at a later stage, ie, from board_late_init()
fixes the issue.
Reported-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Stefano Babic <sbabic@denx.de>
Add device tree based ethernet driver for SMC911X controller on
SMDK5250 boards.
Signed-off-by: Hatim Ali <hatim.rv@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch adds initial dts file for EXYNOS5250 SoC. This dts
file currently include only ethernet devices and properties. More
devices to be added in subsequent patches.
Also add the dts file for SMDK5250 board which uses the EXYNOS5250
dts file.
Signed-off-by: Hatim Ali <hatim.rv@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This commit merges branches from samsung, imx and tegra
meant to fix merge issues between u-boot/master and
u-boot-arm/master, as well as a few manual merge fixes.
Add support for USB host ports on cm-t3530 and cm-t3730.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
This converts MPC8313ERDB NAND boot to use the new SPL infrastructure.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This was already used by some SPL targets, and allows the pad amount to
be specified by board config headers rather than only in makefile
fragments.
Also supply a pad-to of zero if the variable is undefined. It works
without this, but this avoids relying on undocumented behavior.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Add support for ethernet over USB which can be used for e.g. booting
process. It works with tftp and dhcp clients code.
Signed-off-by: Lukasz Dalek <luk0104@gmail.com>
When printing all variables with env print, don't print variables that
begin with '.'. If env print is called with a '-a' switch, then
include variables that begin with '.' (just like the ls command).
Variables printed explicitly will be printed even without the -a.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Move the getenv_yesno() to env_common.c and change most checks for
'y' or 'n' to use this helper.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
commit c73368150 (pmic: Extend PMIC framework to support multiple instances
of PMIC devices) has incorrectly passed the PMIC name under the FSL PMIC case.
Fix that by passing "FSL_PMIC" as the parameter of pmic_get.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Set the gpio value in gpio_direction_output() instead of an extra gpio_set_value
call.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Make the necessary adaptions for the new PMIC framework, so that mx25pdk can
be built again.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
PMIC 2.0 require to test return pointer from pmic_get()
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
According to errata the AM335x device does not support internal delay
mode, so RGMII1_IDMODE and RGMII2_IDMODE must be set to 1.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Instead of passing individual registers by value to board_get_mem_timings,
pass a board_mem_timings structure pointer for the board files to fill in.
Pass same structure pointer to write_sdrc_timings. This saves about
90 bytes of space in SPL.
Signed-off-by: Peter Barada <peter.barada@logicpd.com>
This patch fix following errors
universal.c: In function 'init_pmic_lcd':
universal.c:340: warning: implicit declaration of function 'get_pmic'
universal.c:340: warning: initialization makes pointer from integer without a cast
universal.c: In function 'lcd_power_on':
universal.c:431: warning: initialization makes pointer from integer without a cast
universal.c: At top level:
universal.c:335: warning: 'init_pmic_lcd' defined but not used
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Cc: Donghwa Lee <dh09.lee@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Conflicts:
drivers/power/power_fsl.c
include/configs/mx35pdk.h
include/configs/mx53loco.h
include/configs/woodburn_common.h
board/woodburn/woodburn.c
These boards still use the old old PMIC framework, so they
do not merge properly after the power framework was merged into
mainline.
Fix all conflicts and update woodburn to use Power Framework.
Signed-off-by: Stefano Babic <sbabic@denx.de>
This contains just the minimum information for a coreboot-based board.
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
The device tree now includes the necessary console configuration
information.
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Now that coreboot doesn't need the start16 code, remove it. We need
to remove the CONFIG_SYS_X86_RESET_VECTOR option from coreboot.h also.
Signed-off-by: Simon Glass <sjg@chromium.org>
This prevents the preprocessor from complaining when processing
variadic macros
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Graeme Russ <graeme.russ@gmail.com>
coreboot.c and coreboot_pci.c don't contain board specific but only
coreboot specific code. Hence move it to the coreboot directory in
arch/x86/cpu (which should probably be moved out of cpu/ in another
commit)
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Single rank UDIMM timing has been verified with HMT325U7BFR8C-H9 for speed
800, 900, 1000, 1200, 1300MT/s.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The P5040DS reference board (a.k.a "Superhydra") is an enhanced version of
P3041DS/P5020DS ("Hydra") reference board.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
There were a number of shared files that were using
CONFIG_SYS_MPC85xx_DDR_ADDR, or CONFIG_SYS_MPC86xx_DDR_ADDR, and
several variants (DDR2, DDR3). A recent patchset added
85xx-specific ones to code which was used by 86xx systems.
After reviewing places where these constants were used, and
noting that the type definitions of the pointers assigned to
point to those addresses were the same, the cleanest approach
to fixing this problem was to unify the namespace for the
85xx, 83xx, and 86xx DDR address definitions.
This patch does:
s/CONFIG_SYS_MPC8.xx_DDR/CONFIG_SYS_MPC8xxx_DDR/g
All 85xx, 86xx, and 83xx have been built with this change.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Tested-by: Andy Fleming <afleming@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
This allows DDR configuration to be deferred to the final U-Boot image,
which is able to make use of SPD data. The SPL itself cannot use SPD due
to code size constraints. It previously used fixed register values for
DDR configuration, and those values did not work on the p2020rdb-pca
board I tested with. It's possible that different revisions of the board
require different settings. Using SPD eliminates that problem.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
- Sort by address, and fix column alignment
- Don't label things as localbus that aren't. Instead, put chipselect
info at the end of the description for localbus windows. Note that
NAND/NOR have their chipselects swapped when booting from NAND, and CS2
can be either PMC or VSC7385 depending on hwconfig.
- Shrink NAND to the 32K that's actually mapped in the localbus
- Assign an address and size to L2 SRAM. Remove the similarly named
but unintelligible "L2 SDRAM(REV.)".
- Remove the untrue comment about L1 stack being mapped with TLB0.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
Introduces CONFIG_SPL_RELOC_TEXT_BASE and CONFIG_SPL_RELOC_STACK.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
Harmony contains an SD slot with all 8 bits routed. This allows plugging
in an eMMC-chip-in-SD-form-factor.
Seaboard/Springbank/Ventana/AC100 all have an eMMC chip with all 8 bits
hooked up.
Now that the U-Boot eMMC code fully supports 8-bit operation, initialize
those ports as 8-bit instead of 4-bit to improve performance.
Whistler was already registering its ports as 8-bit.
TrimSlice doesn't have any 8-bit ports.
I don't have any Avionic Design boards nor the Colibri board to test with.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
TrimSlice's USB1 port has two purposes; it either acts as a device port
hosting Tegra's USB recovery protocol, or acts as a host port connected
to the internal USB->SATA bridge chip, which may in turn be connected to
an SSD or HDD. Add the appropriate device tree and board configuration
options to enable this port as a host port, and route the port to the
SATA bridge using the VBUS GPIO.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The Seaboard has a 1366x768 16bpp LCD. The backlight is controlled
by one of the PWMs.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The pulse width/frequency modulation peripheral supports generating
a repeating pulse. It is useful for controlling LCD brightness.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add support for the OTG port on the mx35pdk Personality board.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Tested-by: Stefano Babic <sbabic@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Marek Vasut <marex@denx.de>
This patch enables SPI Booting for EXYNOS5
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch enables SPI driver for EXYNOS5.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Hatim Ali <hatim.rv@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch add support for display on Universal C210 board.
Width of displyed logo must be not bigger than 480 pixel and
is limited by width of the screen.
Tizen logo size is 520x120 pixels and should be resized.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch use software spi on Samsung Universal C210 board.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch turns power down for unused core 1
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Low level initialisation is done by another bootloader
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch use the pinmux for mmc configuration for Universal C210
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch use the pinmux for mmc configuration for Trats
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Full 1GiB is visible
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The inclusion of LCD patch into mx53loco breaks the build when
CONFIG_VIDEO is disabled. Fix this by splitting the video
related stuff to a new file.
Also rename the function lcd_iomux to setup_iomux_lcd to make the
namings aligned with the other iomux functions.
Signed-off-by: Vikram Narayanan <vikram186@gmail.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
The inclusion of LCD patch into mx51evk breaks the build when
CONFIG_VIDEO is disabled. Fix this by splitting the video related
stuff to a new file.
Also rename the function lcd_iomux to setup_iomux_lcd to make the
namings aligned with the other iomux functions.
Signed-off-by: Vikram Narayanan <vikram186@gmail.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
- update clock settings for higher perfomance
- change standard baud rate to 115200
- fix flash base address
- remove unused defines
- add I2C support
- switch form board dependent flash to cfi
- remove board dependent flash code
- use sdram bank 0 instead of bank 1 on boot
- enable on board frame buffer instead external
- remove fake mac address form config
- add watchdog support
- add status led support
Signed-off-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
[agust: fixed small style issues and build warning]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Move pmic_init() function call from board_init() to power_init_board()
to work with new PMIC/POWER framework.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Move pmic_init() function call from board_init() to power_init_board()
to work with new PMIC/POWER framework.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
The battery connected to Samsung's Trats development board is now
charged when voltage drops below threshold.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
When charging battery is necessary, the development board needs to
be turned into low power mode for better efficiency.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Support for TRATS battery has been added. It is treated as a "normal"
power related device and thereof controlled by pmic/power subsystem.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
FG IC built into the MAX8997 device (compliant to MAX17042) is enabled
at TRATS.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
MUIC IC built into the MAX8997 device is enabled at TRATS.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Enable support for power_board_init() method at TRATS board.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
The PMIC framework has been extended to support multiple instances of
the variety of devices responsible for power management.
This change allows supporting of e.g. fuel gauge, charger, MUIC (Micro USB
Interface Circuit).
Power related includes have been moved to ./include/power directory.
This is a first of a series of patches - in the future "pmic" will be
replaced with "power".
Two important issues:
1. The PMIC needs to be initialized just after malloc is configured
2. It uses list to hold information about available PMIC devices
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
fdt.c:91:78: warning: Using plain integer as NULL pointer
fdt.c:103:78: warning: Using plain integer as NULL pointer
speed.c:55:11: warning: symbol 'corecnf_tab' was not declared. Should it be static?
speed.c:519:5: warning: symbol 'do_clocks' was not declared. Should it be static?
mpc8313erdb.c:73:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:74:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:75:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:76:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:79:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:80:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:81:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:82:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:85:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:86:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:87:17: warning: obsolete struct initializer, use C99 syntax
mpc8313erdb.c:88:17: warning: obsolete struct initializer, use C99 syntax
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
fsl_corenet_serdes.c:485:6: warning: symbol '__soc_serdes_init' was not declared. Should it be static?
cpu_init.c:185:6: warning: symbol 'invalidate_cpc' was not declared. Should it be static?
bcsr.c:28:27: warning: non-ANSI function declaration of function 'enable_8568mds_duart'
bcsr.c:39:33: warning: non-ANSI function declaration of function 'enable_8568mds_flash_write'
bcsr.c:46:34: warning: non-ANSI function declaration of function 'disable_8568mds_flash_write'
bcsr.c:53:29: warning: non-ANSI function declaration of function 'enable_8568mds_qe_mdio'
bcsr.c:28:33: warning: non-ANSI function declaration of function 'enable_8569mds_flash_write'
bcsr.c:33:34: warning: non-ANSI function declaration of function 'disable_8569mds_flash_write'
bcsr.c:38:28: warning: non-ANSI function declaration of function 'enable_8569mds_qe_uec'
bcsr.c:63:47: warning: non-ANSI function declaration of function 'disable_8569mds_brd_eeprom_write_protect'
ngpixis.c:245:1: error: directive in argument list
ngpixis.c:247:1: error: directive in argument list
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
We add CONFIG_ENV_VARS_UBOOT_CONFIG,
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG and CONFIG_BOARD_LATE_INIT to set
the variables and then fdtfile and findfdt to make us of this. It is
now possible to do 'run findfdt' to have fdtfile be set to the value of
the dtb file to load for the board we are running on.
Signed-off-by: Tom Rini <trini@ti.com>
This patch extends the am335x_evm board for the AM335x IDK.
The IDK board uses MII for the ethernet phy (same as
Beaglebone board) and MMC0 for storage (but without
card detect line).
The IDK uses UART3 for console. So u-boot must be build
with CONFIG_SERIAL4 and CONFIG_CONS_INDEX=4 or for
the am335x_evm_uart3 board configuration as introduced
by Andrew Bradfords recent patch series "am33xx: Enable
UART {1,2,3,4,5}...". When using the IDK with console on UART0,
those patches are not required. In this case the board
slightly needs to be modified.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
This fixes the following boothang in SPL:
Unknown board, cannot configure pinmux.### ERROR ### Please RESET the board ###
Future commits will add pinmuxes for more on-board peripherals.
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Seaboard has a GPIO that switches an external mux between Tegra's debug
UART and SPI flash. This is initialized from the SPL so that SPL debug
output can be seen. Simplify the code that does this, and don't actually
request the GPIO in the SPL; just program it. This saves ~4.5K from the
size of the SPL, mostly BSS due to the large gpio_names[] table that is
no longer required. This makes Seaboard's SPL fit within the current max
size.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Allen Martin <amartin@nvidia.com>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Seaboard and Ventana are very similar boards, and so share the seaboard.c
board file. The one difference needed so far is detected at run-time by
calling machine_is_ventana(). This bloats the Ventana build with code
that is never used. Switch to detecting Ventana at compile time to remove
bloat. This shaves ~5K off the SPL size on Ventana, and makes the SPL fit
within the max size.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Port USB1 on Whistler is intended as a device port for USB recovery.
Whistler's DT currently contains an alias for this USB port, even though
Whistler's config doesn't enable multiple USB controllers, so the alias
is unused. Remove the unused alias for consistency for now. Similar,
explicitly disable the port in the device tree too.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The ULPI port is routed onto pins on the mini PCI Express connector. A
standard breakout board may be used to access the port.
* Add required DT entries to configure the ULPI port.
* Setup up the ULPI pinmux in the board code.
* Enable multiple USB controller and ULPI support in the board config.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This adds board support for the Toradex Colibri T20 module.
Working functions:
- SD card boot
- USB boot
- Network
- NAND environment
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
For Non-Nvidia boards to include newly added features (like emc clock
scaling) it would be necessary to add each feature to their own board
Makefile. This is because currently the top Makefile automaticly includes
these features only for Nvidia boards.
This patch adds a simple Makefile include so all new features become
available for non-Nvidia board vendors.
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Thierry Reding <thierry.reding@avionic-design.de>
Cc: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The M54418TWR lds file need to update since commit:
8b493a5236
common: Discard the __u_boot_cmd section
The command declaration now uses the new LG-array method to generate
list of commands. Thus the __u_boot_cmd section is now superseded and
redundant and therefore can be removed. Also, remove externed symbols
associated with this section from include/command.h .
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Once more, some of the previous changes caused the code to grow, which
causes errors like
u-boot.lds:74 cannot move location counter backwards (from 40008384 to 40008000)
when building with some older tool chains (like ELDK 4.2).
Adjust the linker script to make fit again.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Conn Clark <clark@esteem.com>
Once more, some of the previous changes caused the code to grow, which
causes errors like
u-boot.lds:80 cannot move location counter backwards (from 400082a4 to 40008000)
when building with some older tool chains (like ELDK 4.2).
Adjust the linker script to make fit again.
Signed-off-by: Wolfgang Denk <wd@denx.de>
These boards have long reached EOL, and there has been no indication
of any active users of such hardware for years. Get rid of the dead
weight.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Wolfgang Grandegger <wg@denx.de>
Added clock settings for MFC, FIMC, FB and G3D. They are clocked to
maximum respective frequencies as per datasheet.
Signed-off-by: Annamalai Lakshmanan <annamalai.lakshmanan@linaro.org>
Signed-off-by: Giridhar Maruthy <giridhar.maruthy@linaro.org>
Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org>
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
SX1 does not build properly by itself, is not built
as part of MAKEALL arm or MAKEALL -a arm, and is only
present in Makefile, not boards.cfg. As it also has no
entry in MAINTAINERS, it is orphan and non-functional.
Remove it.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
mx25pdk has a Ethernet port that is connected to its internal FEC controller.
In order to power up the Ethernet PHY (DP83640) it is necessary to communicate
with the MC34704 PMIC via I2C.
Make the FEC ethernet port functional
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
imx-regs.h is meant to contain SoC register definitions.
Common SoC funtions should go to sys_proto.h instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
mx25pdk has a SD/MMC slot connected to esdhc1.
Add support for it and allow the environment variables to be saved into SD/MMC.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
The woodburn board is based on the MX35 SOC.
Support for both external (NOR) and internal
(SD Card) boot mode are added. It uses the
generic SPL framework to implement the internal boot
mode.
The following peripherals are supported:
- Ethernet (FEC)
- SD Card
- NAND (512 MB)
- NOR Flash
In the internal boot mode, a simple imximage header
is generated to set the address in internal RAM
where the SOC must copy the SPL code. The initial setup
is then demanded to the SPL itself.
Signed-off-by: Stefano Babic <sbabic@denx.de>
This patch modifies start.S for the arm1136 to make it
conform to start.S in armv7 architecture, to make it
usable if the SPL framework is used.
Signed-off-by: Stefano Babic <sbabic@denx.de>
If configured to use UART{1,2,3,4,5} such as on the Beaglebone RS232
cape or on the am335x_evm daughterboard, enable the proper pin-muxing.
Signed-off-by: Andrew Bradford <andrew@bradfordembedded.com>
Move the hardcoded ddr2/ddr3 settings for the ti boards to board code,
so other boards can use different types/timings.
Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
[trini: Make apply with rtc32k_enable() in the file]
Signed-off-by: Tom Rini <trini@ti.com>
The i2c header is specific to ti(-derived) boards, and not generic for all
am335x boards.
Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
[trini: Make re-apply with rtc32k_enable() applied]
Signed-off-by: Tom Rini <trini@ti.com>
Some GPIOs differ in the new revision board.
Previous revision are considered obsolete and
they will not anymore supported.
Signed-off-by: Stefano Babic <sbabic@denx.de>
The mcx board was slightly modified and the pinmux must be updated.
There is no need to support the old board, that becomes obsolete.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Add Freescale MCF54418TWR ColdFire development board support.
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Alison Wang <b18965@freescale.com>
Add support for Keymile boards based on mpc8309
(it would be only kmvect1 for now)
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
[#elseif -> #if to allow kmcoge5ne and kmeter1 to build successfully]
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The T4240QDS is a high-performance computing evaluation, development and
test platform supporting the T4240 QorIQ Power Architecture™ processor.
SERDES Connections
32 lanes grouped into four 8-lane banks
Two “front side” banks dedicated to Ethernet
Two “back side” banks dedicated to other protocols
DDR Controllers
Three independant 64-bit DDR3 controllers
Supports rates up to 2133 MHz data-rate
Supports two DDR3/DDR3LP UDIMM/RDIMMs per controller
QIXIS System Logic FPGA
Each DDR controller has two DIMM slots. The first slot of each controller
has up to 4 chip selects to support single-, dual- and quad-rank DIMMs.
The second slot has only 2 chip selects to support single- and dual-rank
DIMMs. At any given time, up to total 4 chip selects can be used.
Detail information can be found in doc/README.t4qds
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Add code for configuring VSC3316/3308 crosspoint switches
Add README to understand the APIs
- VSC 3316/3308 is a low-power, low-cost asynchronous crosspoint switch
capable of data rates upto 11.5Gbps. VSC3316 has 16 input and 16
output ports whereas VSC3308 has 8 input and 8 output ports.
Programming of these devices are performed by two-wire or four-wire
serial interface.
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
According to new QIXIS system definition, update QIXIS registers set
to add present2 register instead of obsolete ctl_sys2.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The command declaration now uses the new LG-array method to generate
list of commands. Thus the __u_boot_cmd section is now superseded and
redundant and therefore can be removed. Also, remove externed symbols
associated with this section from include/command.h .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Add section for the linker-generated lists into all possible linker
files, so that everyone can easily use these lists. This is mostly
a mechanical adjustment.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
QIXIS FPGA layout defines the address of registers but The actual register bit
implementation is board-specific,
So avoid use of magic numbers as it may vary across different boards's QIXIS
FPGA implementation.
Also, Avoid board specific defines in common/qixis.h
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Some of the boards still used the old PXA_MMC driver instead of the
new generic one. Use the new one instead so the old can be removed
and the generic MMC framework can be properly used.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andy Fleming <afleming@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
With ELDK4.2 libserial.o is too large to fit in the area before the
environment. Swap in libinput instead which is a little smaller.
Cc: Michael Schwingen <michael@schwingen.org>
Signed-off-by: Tom Rini <trini@ti.com>
The sbc8548/60 (both similar, just variations in UART hardware)
support has been removed from the linux kernel as of v3.6-rc1~132
so lets also now remove it from the u-boot tree as well.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Move input_data() and friends to board/cpc45/ide.c, as overrides for weak
aliases in cmd_ide.c
note: checkpatch emits warnings about using volatile
Signed-off-by: Pavel Herrmann <morpheus.ibis@gmail.com>
This changes input_data() and friends from static function to global symbols
under weak alias, to enable board specific overrides (and therefore get rid of
board-specific code in cmd_ide.c)
Also declare ide_bus_offset in the header file, so other files can use
ATA_CURR_BASE as well.
Signed-off-by: Pavel Herrmann <morpheus.ibis@gmail.com>
Replace the in-place ad-hoc implementation of serial_puts() within
the drivers with default_serial_puts() call. This cuts down on the
code duplication quite a bit.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
As the board seems to be unmaintained for some time, lets remove
the support in mainline completely.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: James F. Dougherty <jfd@broadcom.com>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
We define CONFIG_SYS_TEXT_BASE in board's specified header file.
So config.mk is useless, then remove it.
Signed-off-by: Zhizhou Zhang <etou.zh@gmail.com>
Adds support for HDMI, two LVDS panels and one RGB panel to
the SABRE-Lite board.
Displays supported:
HDMI - 1024 x 768 for maximum compatibility
Hannstar-XGA - 1024 x 768 LVDS (Freescale part number MCIMX-LVDS1)
wsvga-lvds - 1024 x 600 LVDS (Boundary p/n Nit6X_1024x600)
wvga-rgb - 800 x 480 RGB (Boundary p/n Nit6X_800x480)
Since the ipuv3_fb display driver currently supports only a single display,
this code auto-detects panel by probing the HDMI Phy for Hot Plug Detect
or the I2C touch controller of the LVDS and RGB displays in the priority
listed above.
Setting 'panel' environment variable to one of the names above will
override auto-detection.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
The kernel from Freescale expects that the bootloader passes the board revision.
Read the board revision and pass it via get_board_rev().
Without passing the board revision the kernel does not operate properly as the
initialization of peripherals are different in revA versus revB boards.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
On mxc, each SDHC instance has a dedicated clock, so gd->sdhc_clk is not
suitable for the multi-instance use case (initialization made directly with
fsl_esdhc_initialize()).
This patch fixes this issue by adding a configuration field for the SDHC input
clock frequency.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Eric Bénard <eric@eukrea.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Jason Liu <r64343@freescale.com>
Cc: Matt Sealey <matt@genesi-usa.com>
Cc: Andy Fleming <afleming@gmail.com>
Clean up mx35 lowlevel_init:
- Indent with tabs.
- Fix comments.
- Use defined values instead of literal constants.
- Use defined macros instead of duplicating code.
- Use macro parameters with default values instead of #define'd configs.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Add basic support for HP iPAQ h2200 palmtop. h2200 palmtop was targeted
to general consumers. It has 64 MB of RAM, 32 MB flash. No intergrated
Wi-Fi nor Ethernet. Based on Intel PXA255 processor. It was shipped with
Windows CE 4.2 operating system.
Signed-off-by: Lukasz Dalek <luk0104@gmail.com>
Clean up mx25 lowlevel_init:
- Add comments.
- Do not use write32 repeatedly with the same value in order not to increase
code size.
- Make register values configurable.
- Use macro parameters with default values instead of literal constants.
- Use defined macros instead of duplicating code.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: John Rigby <jcrigby@gmail.com>
Cc: Matthias Weisser <weisserm@arcor.de>
The CSI PODF bit-field used by the previous code for the i.MX31 CCM PDR0
register is actually composed of two bit-fields: one pre-divider and one
post-divider. This patch fixes the CCM access macros and the code using them
accordingly.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Define default SoC input clock frequencies for i.MX5/6 in order to get rid of
duplicated definitions.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Jason Liu <r64343@freescale.com>
Cc: Matt Sealey <matt@genesi-usa.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
mx6qsabreauto is a board based on mx6q SoC with the following features:
- 2GB of DDR3
- 2 USB ports
- 1 HDMI output port
- SPI NOR
- 2 LVDS LCD ports
- Gigabit Ethernet
- Camera
- eMMC and SD card slot
- Multichannel Audio
- CAN
- SATA
- NAND
- PCIE
- Video Input
Add very basic support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
mx6qsabresd has a AR8031 Gigabit PHY.
Add support for it.
Also increase CONFIG_SYS_MALLOC_LEN so that FEC buffer allocation does not fail.
Tested on 1Gbp and 100Mbps networks.
Suggested-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
mx6qsabresd is a board based on mx6q SoC with the following features:
- 1GB of DDR3
- 1 USB OTG port
- 1 HDMI output port
- SPI NOR
- LVDS panel
- Gigabit Ethernet
- Camera Connector
- eMMC and SD card slot
- Audio
Add very basic support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Boards may require a different pinmux setup for NAND than the default one.
Add a way to call into board specific code to set this up.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The prototypes used in board files were all scattered out, which lead to
code duplication between SPL and normal U-Boot and some prototypes not actually
being used. Consolidate this in a common board header.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Rename board provided gpio_config_uart() to
gpio_early_init_uart() as it does the same thing as the equally
called function provided by the uart-switch code. This allows
to simply call this function in early board init whether or not
we are building with CONFIG_UART_SWITCH defined.
Also provide a weak symbol for this function, to avoid the
need to provide this function for boards that don't need any
fixup.
This patch supersedes the earlier posted
"tegra: convert gpio_config_uart to weak symbol".
Build tested with MAKEALL -s tegra20
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The move is pretty straight-forward. ap20.h and tegra20.h were renamed to ap.h and tegra.h.
Some files remain in arch-tegra20 but 'include' a file in 'arch-tegra' with #defines & structs
that will be common between T20 and T30 HW. HW-specific #defines, etc. stay in the 'arch-tegra20'
'root' file.
All boards build OK w/MAKEALL -s tegra20. Checkpatch.pl runs clean. Seaboard works OK.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Medcom is the marketing name for an older, PXA-based version of the same
device. In order to avoid confusion, rename the Tegra-based version to
the new marketing name.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The official vendor prefix for Avionic Design is now "ad". Update the
board DTS files accordingly.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Kill off ehci-core.h
It was used to specify some static controller data. To support more than
one controller being active at any time we have to carry the controller
data ourselfes. Change the ehci interface accordingly.
NOTE: OMAP implemented the ehci stuff a bit backwards and should be fixed
to do the same thing as other platforms. But the change for now is at least
compile clean.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Carry an index in the lowlevel usb functions to make specify the
respective usb controller.
Also pass through an controller struct from lowlevel_init to the
creation of the root usb device of this controller.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Reviewed-by: Marek Vasut <marex@denx.de>
The env_ptr is already declared in environment.h, so there is no need to
redeclare in board files (especially after including the environment.h)
Remove those declarations.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Matthias Fuchs <matthias.fuchs@esd.eu>
As the board seems to be unmaintained for some time, lets remove
the support in mainline completely.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: James MacAulay <james.macaulay@amirix.com>
Acked-by: Marek Vasut <marex@denx.de>
As the board seems to be unmaintained for some time, lets remove
the support in mainline completely.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Peter De Schrijver <p2@mind.be>
Acked-by: Marek Vasut <marex@denx.de>
Remove the support for not-CONFIG_SERIAL_MULTI part from serial
port drivers and some board files. Since CONFIG_SERIAL_MULTI is
now enabled by default, that part is a dead code. Remove it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Implement support for CONFIG_SERIAL_MULTI into p3mx serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the p3mx driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Implement support for CONFIG_SERIAL_MULTI into sconsole serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the sconsole driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Implement support for CONFIG_SERIAL_MULTI into ml2 serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the ml2 driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Implement support for CONFIG_SERIAL_MULTI into evb64260 serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the evb64260 driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Implement support for CONFIG_SERIAL_MULTI into cpci750 serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the cpci750 driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Implement support for CONFIG_SERIAL_MULTI into cogent serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the cogent driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Implement support for CONFIG_SERIAL_MULTI into bmw serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the bmw driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Implement support for CONFIG_SERIAL_MULTI into amirix serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the amirix driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Implement support for CONFIG_SERIAL_MULTI into marvell serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the marvell driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Remove the prototypes for zoom2_serial_deviceN from serial.h . This
can't be done right away, as they are referenced from the zoom2
config file. Therefore, adjust the code so the config file only
specifies number of the port. Then, replace the simple return in
default_serial_console() with a switch across possible values, which
returns the zoom2_serial_deviceN . With such adjustment in place,
the exported prototypes in serial.h can be safely removed.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Make use of the newly implemented weak default_serial_console in
the serial_pxa driver. This removes all reimplementations of this
function from board files.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Properly spell out the whole structure member names when an initialized
varible is instantiated from the struct serial_driver. In case the
structure definition for struct serial_driver undergoes reordering,
there will be no impact on variables defined based on this structure.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: C Nauman <cnauman@diagraph.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Michal Simek <monstr@monstr.eu>
Kill multiple occurances and redeclaration of MK_STR
in favor of __stringify().
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Under option -munaligned-access, gcc can perform local char
or 16-bit array initializations using misaligned native
accesses which will throw a data abort exception. Fix files
where these array initializations were unneeded, and for
files known to contain such initializations, enforce gcc
option -mno-unaligned-access.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
[trini: Switch to usign call cc-option for -mno-unaligned-access as
Albert had done previously as that's really correct]
Signed-off-by: Tom Rini <trini@ti.com>
Due to grown code sizes the TQM85xx boards don't build any more with
some older tool chains (like ELDK 4.2). As these boards have long
reached EOL it seems a waste of effort trying to fix them. The vendor
has agreed to drop support for them, too. So let's get rid of them.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
cc: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Stefan Roese <sr@denx.de>
The wrong value was set as value of column of DDR memory for ap_sh4a_4a.
10 is the right value. This fixed this problem.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add minimal support for Altera's SOCFPGA Cyclone 5 hardware.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Signed-off-by: Chin Liang See <clsee@altera.com>
Signed-off-by: Pavel Machek <pavel@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Tom Trini <trini@ti.com>
Cc: Wolfgang Denx <wd@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Stefan Roese <sr@denx.de>
----
v8: Remove no_return attribute for reset_cpu
Based on v2012.10-rc2
Without usb-serial cable plugged at this stage, some
garbage is seen in UART RX FIFO, which blocks autoboot
progress. The fix makes sure to empty the RX FIFO,
before we wait for user input to interrupt autoboot.
Signed-off-by: Ramesh Chandrasekaran <ramesh.chandrasekaran@stericsson.com>
Add support for Xilinx Zynq board.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Acked-by: Marek Vasut <marex@denx.de>
CC: Joe Hershberger <joe.hershberger@gmail.com>
This patch adds support for the X600 SPEAr600 based board. Its also
the first SPEAr600 board that uses the newly introduced SPEAr600
SPL support. Xloader is not necessary any more. By using the new
"u-boot.spr" make target, one image will generated containing both,
U-Boot SPL (with mkimage header as needed by the SPEAr BootROM, and
the main U-Boot with mkimage header.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Amit Virdi <amit.virdi@st.com>
Cc: Vipin Kumar <vipin.kumar@st.com>
If while booting the power switch is in OFF position, turn off the fan,
too.
Signed-off-by: Michael Walle <michael@walle.cc>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
The kmnusa board uses a mv88e6352 switch that is connected to the main
eth interface of the kirkwood. Therefore the switch must be configured
so that the kirkwood's egiga eth inferface can be used.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Cc: Holger Brunck <holger.brunck@keymile.com>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Acked-By: Prafulla Wadaskar <prafulla@marvell.com>
The hardware design of the IB-NAS62x0 causes the SATA activity
LEDs to be on when idle by default. Reverse the polarity of the
activity LEDs in early init.
Signed-off-by: Simon Baatz <gmbnomis@gmail.com>
Cc: Luka Perkov <uboot@lukaperkov.net>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Acked-by: Luka Perkov <uboot@lukaperkov.net>
Some boards may differ only in the SDRAM size. This function allows to
fix the size accordingly and we can use the same u-boot binary for both
boards.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
This patch adds support for the LaCie boards Network Space v2 (Lite and
Mini). This two boards are derived from the Network Space v2 and a lot
of hardware caracteristics are shared.
- CPU: Marvell 88F6192 800Mhz
- SDRAM memory: 128MB DDR2 200Mhz
- 1 SATA port: internal
- Gigabit ethernet: PHY Marvell 88E1318
- Flash memory: SPI NOR 512KB (Macronix MX25L4005A)
- i2c EEPROM: 512 bytes (24C04 type)
- 2 USB2 ports (Lite only): host and host/device
- 1 push button
- 1 SATA LED (bi-color, blue and red)
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Support of the MINI2440 board from FriendlyARM from
an old version of u-boot :
http://repo.or.cz/r/u-boot-openmoko/mini2440.git
Currently, supporting only boot from NOR.
Signed-off-by: Gabriel Huau <contact@huau-gabriel.fr>
This initializes GPIO, without using PFC framework in
board_early_init_f function. It is because it cannot initialize
normally when PFC is used.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Do soft power on reset in U-Boot reset command.
Signed-off-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Problem:
Linux kernel hangs up when it write a file to NFS mounted directory.
Solution:
Modify bus controller setting for CS4, which connected smsc9221 ethernet
controller.
Detail:
Modify CS4BCR bit[29:28] (IWW[1:0]) from 00 to 01.
Modify CS4BCR bit[20:19] (IWRRD[1:0]) from 00 to 01.
Modify CS4BCR bit[17:16] (IWRRS[1:0]) from 00 to 01.
Modify CS4WCR bit[27:26] (WSW[1:0]) from 10 to 11
Modify CS4WCR bit[25:24] (WHW[1:0]) from 01 to 10
Modify CS4WCR bit[18:16] (WW[2:0]) from 101 to 111
Modify CS4WCR bit[13:11] (SW[2:0]) from 010 to 011
Modify CS4WCR bit[10:7] (WR[3:0]) from 1000 to 1011
Signed-off-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The KZM-A9-GT board has Renesas R-Mobile SH73A0, 512MB DDR2-SDRAM,
USB, Ethernet, and more.
This patch supports the following functions:
- 512MB DDR2-SDRAM
- 16MB NOR Flash memory
- Serial console (SCIF)
- Ethernet (SMSC)
- I2C
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Some of the previous changes caused the code to grow, which causes
errors like
u-boot.lds:76 cannot move location counter backwards (from 4000828c to 40008000)
when building with some older tool chains (like ELDK 4.2).
Adjust the linker script to make fit again.
Signed-off-by: Wolfgang Denk <wd@denx.de>
This patch adds support for networking in SPL. Some devices are
capable of loading SPL via network so it makes sense to load the
main U-Boot binary via network too. This patch tries to use
existing network code as much as possible. Unfortunately, it depends
on environment which in turn depends on other code so SPL size
is increased significantly. No effort was done to decouple network
code and environment so far.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@ti.com>
Do not allow to overwrite it when video is enabled.
Signed-off-by: Bastian Ruppert <Bastian.Ruppert@Sewerin.de>
CC: Tom Rini <trini@ti.com>
Acked-by: Stefano Babic <sbabic@denx.de>
The AP1000 defines a 'get_device' function to determine what board
revision we are on. Inline that checking as it conflicts with the
get_device() in <part.h> and is only used once.
Signed-off-by: Tom Rini <trini@ti.com>
This file documents when to build for da850evm and when to build for
da850_am18xxevm. It also documents how to write the u-boot.ais file to
persistent storage (such as SPI), in some cases as well as how to write
a recovery image.
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Christian Riesch <christian.riesch@omicron.at>
Acked-by: Prabhakar Lad <prabhakar.lad@ti.com>
Only omap4/5 currently have a meaningful set of display text and overo
had been adding a function to display nothing. Change how this works to
be opt-in and only turned on for omap4/5 now.
Signed-off-by: Tom Rini <trini@ti.com>
fecmxc_mii_postcall() is specific to the KSZ9021 PHY on m28evk and
should not be used on mx28evk, which has LAN8270 instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
The NAND Flash of the KARO TX25 board is a Samsung K9F1G08U0B with 25-ns R/W
cycle times. However, the NFC clock for this board was set to 66.5 MHz, so using
the NFC driver in symmetric mode (i.e. 1 NFC clock cycle = 1 NF R/W cycle)
resulted in NF R/W cycle times of 15 ns, hence corrupted NF accesses.
This patch fixes this issue by setting the NFC clock to the highest frequency
complying to the 25-ns NF R/W cycle times specification, i.e. 33.25 MHz.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: John Rigby <jcrigby@gmail.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Daniel Gachet <Daniel.Gachet@hefr.ch>
Acked-by: Stefano Babic <sbabic@denx.de>
FSL 2.6.35 kernel assumes that the bootloader passes the CONFIG_REVISION_TAG
information.
If this data is not present, the kernel misconfigures the TZIC, which results in
the timer interrupt handler never being called, so the kernel deadlocks while
calibrating its delay.
Suggested-by: Greg Topmiller <Greg.Topmiller@jdsu.com>
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
