The udelay() function in lib/time.c contains a WATCHDOG_RESET()
call. So use __udelay() in max6370_wdt.c to prevent recursion.
Fixes: 0a095fc53b ("watchdog: Add MAX6370 watchdog timer driver")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
The udelay() function in lib/time.c contains a WATCHDOG_RESET()
call. The only reason this doesn't lead to a catastrophic infinite
recursion is due to the rate-limiting in wdt-uclass.c:
if (time_after_eq(now, priv->next_reset)) {
priv->next_reset = now + priv->reset_period;
wdt_reset(dev);
}
But this would fall apart if ->next_reset was updated after calling the
device's reset method.
This is needlessly fragile, and it's easy enough to avoid that
recursion in the first place by just using __udelay() directly.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Stefan Roese <sr@denx.de>
xilinx:
- Add support for new Versal NET SOC
zynqmp:
- Use mdio bus for ethernet phy description
- Wire ethernet phy reset via i2c-gpio
versal:
- Config cleanup
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYzGwogAKCRDKSWXLKUoM
Ial4AJ9+4WHn0MV2X7gK1fyh4lUW7ggPhQCggsYlSoACgMgdji17SAPhCv/W3IA=
=BmA9
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2023.01-rc1-v2' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2023.01-rc1 (round 2)
xilinx:
- Add support for new Versal NET SOC
zynqmp:
- Use mdio bus for ethernet phy description
- Wire ethernet phy reset via i2c-gpio
versal:
- Config cleanup
Currently all GPIOs supported by CMD_EXT_CONTROL/CMD_GET_EXT_CONTROL_STATUS
commands (last 16 GPIOs) are available only when FEAT_PERIPH_MCU feature
bit is set. So do not register these GPIOs by U-Boot driver when this
feature bit is not set, so U-Boot 'gpio' command would see only GPIOs which
really exists.
Fixes: 5e4d24ccc1 ("gpio: Add Turris Omnia MCU driver")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
When processing USB_REQ_CLEAR_FEATURE, USB_REQ_SET_FEATURE, and
USB_REQ_GET_STATUS packets in dwc2_ep0_setup an out of bounds access
can occur. This is caused by the wIndex field of the usb control packet
being used as an index into an array whose size is DWC2_MAX_ENDPOINTS (4).
Signed-off-by: Alison Huffman <alisn@google.com>
At present sandbox is producing a warning about SCSI migration. Drop the
legacy code and replace it with a new implementation.
Also drop the SATA command, which does not work with driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move this code out of the helper function so we can (later) add it as part
of the shared emulation code. Set a default value of 0 for buff_used since
that is what we use when there is an error.
Signed-off-by: Simon Glass <sjg@chromium.org>
In preparation for sharing the emulation code between two drivers, move
some of the fields into a new struct. Use a separate header file so it
can be used by various drivers.
Signed-off-by: Simon Glass <sjg@chromium.org>
This has the same name as a field in our local private struct, which is
confusing. Change the name to xfer_len instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Changing baudrate is a sensitive operation. To ensure that U-Boot messages
printed before changing baudrate are not lost, call new U-Boot console
flush() function.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Like in all other console functions, implement also serial_flush() function
as a fallback int console flush() function.
Flush support is available only when config option CONSOLE_FLUSH_SUPPORT is
enabled. So when it is disabled then provides just empty static inline
function serial_flush().
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
UART drivers have putc/puts functions which just put characters into HW
transmit queue and do not wait until all data are transmitted.
Implement flush callback via serial driver's pending(false) callback which
waits until HW transmit all characters from the queue.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
During init_dram() is called also compute_lowest_common_dimm_parameters()
function which prints multi-line detailed output. So print also re-aligning
filler after "Detected ?DIMM" line to have "DRAM: " output aligned.
Signed-off-by: Pali Rohár <pali@kernel.org>
U-Boot core code already handles the case when RAM size is bigger than
CONFIG_MAX_MEM_MAPPED. So there is no need to do duplicate check in fsl ddr
driver for CONFIG_MAX_MEM_MAPPED. Instead simplify code to just check if
RAM size can be representable in phys_size_t type. And avoid printing
warning if phys_size_t is just 1 byte smaller than RAM size, which is the
typical situation with 4 GB DDR module.
Signed-off-by: Pali Rohár <pali@kernel.org>
Function fsl_ddr_compute() always return size in unsigned long long type,
but function fsl_ddr_sdram_size() returns size in phys_size_t type.
When 36-bit addressing mode is not enabled then phys_size_t type is only
32-bit and thus it cannot store value 4GB (0x100000000). Function
fsl_ddr_sdram_size() in this case returns truncated value 0x0.
Fix this issue by returning the highest representable value, which is
0xffffffff (4GB - 1 byte).
This change fixes crashing of proper U-Boot because it detected 4 GB module
as RAM with zero size.
Signed-off-by: Pali Rohár <pali@kernel.org>
Check needs to be done against CONFIG_MAX_MEM_MAPPED macro and not fixed
size 4GB (as CONFIG_MAX_MEM_MAPPED can be lower and for example for e500
cores it is just 2GB). Also fix printf re-align, which should be applied
only for non-SPL builds, during init_dram() call.
Signed-off-by: Pali Rohár <pali@kernel.org>
Add basic CPU driver used to retrieve CPU model information.
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds clock driver support for MediaTek MT7981 SoC
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds clock driver support for MediaTek MT7986 SoC
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This adds the CLK_XTAL macro/flag to allow modeling clocks which are
directly connected to the xtal clock.
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds infrasys clock mux support for mediatek clock drivers.
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds support for a clock node to configure its parent clock
where possible.
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
The mtk clock framework in u-boot uses array index for searching clock
parent (kernel uses strings for search), so we need to specify a special
clock with ID=0 for CLK_XTAL in u-boot.
In the mt7622/mt7629 clock tree, the clocks with ID=0 never call
mtk_topckgen_get_mux_rate, adn return xtal clock directly. This what we
expected.
However for newer chips, they may have some clocks with ID=0 not
representing the xtal clock and still needs mtk_topckgen_get_mux_rate be
called. Current logic will make entire clock driver not working.
This patch adds a flag to indicate that whether a clock driver needs clocks
with ID=0 to call mtk_topckgen_get_mux_rate.
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds pinctrl and gpio support for MT7986 SoC
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds pinctrl and gpio support for MT7981 SoC
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds support for MediaTek I2C interface
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds support for spi-mem controller found on newer MediaTek SoCs
This controller supports Single/Dual/Quad SPI mode.
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: SkyLake.Huang <skylake.huang@mediatek.com>
Add watchdog support for MediaTek MT7986 SoC
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch add general-purpose timer support for MediaTek MT7981/MT7986.
These two SoCs uses a newer version of timer with its register definition
slightly changed.
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds PWM support for MediaTek MT7981 SoC.
MT7981 uses a different register offset so we have to add a version field
to indicate the IP core version.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
The baud clock on some platform may change due to assigned-clock-parent
set in DT. In current flow the baud clock is only retrieved during probe
stage. If the parent of the source clock changes after probe stage, the
setbrg will set wrong baudrate.
To get the right clock rate, this patch records the baud clk struct to the
driver's priv, and changes the driver's flow to get the clock rate before
calling _mtk_serial_setbrg().
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds support for MediaTek MT7981 and MT7986. Both chips uses
PDMA v2.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds support for PDMA v2 hardware. The PDMA v2 has extended the
DMA descriptor to 8-words, and some of its fields have changed comparing
to the v1 hardware.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch is a preparation for adding a new version of PDMA of which the
DMA descriptor fields has changed. Using bitfields will result in a complex
modification. Convert bitfields to u32 units can solve this problem easily.
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Using a single soc id to control different initialization and TX/RX flow
for all SoCs is not extensible if more hardware variations are added in
the future.
This patch introduces a struct to replace the original mtk_soc to allow
the driver be able handle newer hardwares.
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Add eMMC and SDXC support for MediaTek MT7981/MT7986 SoCs
Both chips support SDXC and eMMC 4.5. MT7986A supports eMMC 5.1.
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmMoEdgcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyNvEB/4nEeiBx7Lo1gK+79PJ
9kCUngglHRu3/+FJMpcOp+2b6sSW1IZs8qGBMAMFSRoFElrLMMbVEgBR0ZfJCl3c
It0xN9Buhe8muwtAdE8Amr4PddUEynzglVPpFUFfir6ZqFAcedmN6iuh+K82r7Be
7s/8tRb2hVp//TpkEntf2yxrYnyeW4qiXyUxbUhaUyyhkM3RBXySuY4qnaaLp3NY
R9rsIY5j3kA2QylebEamlXI+KDvszrGbkUOUUrlwkygQNR/GmAYQPlY1TdBwk0wE
U1CO8zQYaL3OY998lU32pMVClmwyXbn2i7KAyMm3TEgrfpjQsLTS2BK+w+RBdMGL
XGnt
=lRvM
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2023.01-a' of https://source.denx.de/u-boot/custodians/u-boot-at91 into next
First set of u-boot-at91 features for the 2023.01 cycle:
This feature set includes the important update on PIO4 pinctrl driver
that solves a long time mismatch between Linux and U-boot, related on
the unification of pinctrl and gpio driver support, now respecting the
pinctrl bindings ABI; and also support for pinctrl subnodes. The feature
set also adds support for PDA screen detection for sam9x60_curiosity
board , one fix for SD-Card reinsertion and one fix for sam9x60 clocks.
Add timer_get_boot_us() to support boards, that have CONFIG_BOOTSTAGE
enabled, like pogo_v4.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Tony Dinh <mibodhi@gmail.com>
This patch adds support for other Marvell Armada SoC's, supporting the
25MHz fixed clock operation, like the Armada XP etc.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Tony Dinh <mibodhi@gmail.com>
This driver is not used by any system and is long unmaintained, drop it.
There is a DWC2 OTG driver which is maintained, see CONFIG_USB_GADGET_DWC2_OTG .
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Previously, in order for the `pinctrl-*` DT node properties
to be properly processed, the pinctrl's subnodes were limited
to only having the `pinmux` property as well as other additional
properties (slew-rate, bias-disable, etc.). Now, with this patch
the pinctrl driver is made to work similarly to the one from Linux.
It can now distinguish between one subnode and a subnode with multiple
subnodes.
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
This has been done in order to align the DT of U-Boot with the DT
of Linux. In Linux, a phandle from a '-gpio' DT property is linked
to the pinctrl driver, a single driver that handles both pinctrl
settings and offers GPIO API to callers. On the other hand,
U-Boot redirects such phandle to a corresponding UCLASS_GPIO
driver, because U-Boot offers two different types of drivers
in this case: UCLASS_PINCTRL which handles pin functions and
UCLASS_GPIO which handles gpio requests as a gpio provider.
Due to this, we have two drivers in Uboot, but the Devicetree
has a single node. Thus, just one of the drivers can be probed
for the DT node during platform initialization, before relocation.
Our previous solution in U-Boot was to have a different devicetree:
the gpio node has a subnode for the pinctrl driver, which
is not compliant with Linux ABI. Furthermore, our documentation
for this type of nodes mentions no such gpio compatible.
After this patch, we can no longer add nodes with a gpio
compatible in the DT. Thus, in order to link the pinctrl driver to
the gpio one, a hook to the bind method of the former in U-Boot has
been added and the GPIO related compatibles have been removed to
avoid conflict when compatibles are enumerated and bound to drivers
during platform start before relocation. The bind method will attach
the GPIO driver to the pinctrl DT node so that every phandle coming
from '-gpio' DT properties will be redirected to a valid driver
attached to the pinctrl DT node.
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
ddrck and qspick should have mck_div as parent clocks to be in sync with
linux driver.
Signed-off-by: Mihai Sain <mihai.sain@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Whenever the SD Card would be removed and then re-inserted while in the
U-Boot command line, the `SDBPWR` bit of the `SDMMC_PCR` register would
remain unset afterwards. In order for the bit to be set again after
re-insertion, register an additional `deferred_probe` method that the
DM would then transparently call. This method will call the generic
`sdhci_probe` which will, during its execution flow, set this bit to 1.
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
Reported-by: Mihai Sain <mihai.sain@microchip.com>
Reviewed-by: Eugen Hristev <eugen.hristev@microchip.com>
only waiting for TXEMPTY leads to corrupted messages going over the
wire - which is fixed by making use of the FIFO
this change is following the linux kernel uart driver
(drivers/tty/serial/imx.c), which also checks UTS_TXFULL
instead of UTS_TXEMPTY
Signed-off-by: Johannes Schneider <johannes.schneider@leica-geosystems.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
on imx8(mm) the RXDMUXSEL needs to be set for data going over the wire
(as observable on a connected 'scope) to actually make it into the
RXFIFO
the reference manual is not overly clear about this, and only
mentiones that "UCR3_RXDMUXSEL should always be set." - and since the
CR3 register reverts to its reset values after setting the baudrate,
setting this bit is done during '_mxc_serial_setbgr'
Signed-off-by: Johannes Schneider <johannes.schneider@leica-geosystems.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The ddrphy_utils.c is now deduplicated in drivers/ddr/imx/phy/ddrphy_utils.c ,
this drivers/ddr/imx/imx8m/ddrphy_utils.c is a remnant from when the
deduplication was implemented and was not removed. Remove it as it is
unused.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
wrong end address passed to flush_dcache_range.
modified the flush_dache logic for scatter list elements.
Fixes: 1919f58a8f (crypto/fsl: fsl_hash: Fix dcache issue in caam_hash_finish)
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
The i.MXRT11 series has different offsets for IOCR_MUX, it also can
address 64MiB of SDRAM so add a macro for that.
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
The i.MXRT11 series has two new pll types but are variants of existing.
This patch adds the ability to read one of the pll types' frequency
as it can't be changed unlike the generic pll it also has the
division factors swapped.
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
While testing on some Kirkwood platforms it was noticed that the timer
did not function correctly all the time. The driver did not correctly
handle 32bit timer value wrap arounds. Using the timer_conv_64()
conversion function fixes this issue.
Fixes: e9e73d78a8 ("timer: add orion-timer support")
Suggested-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier-oss@weidmueller.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Tony Dinh <mibodhi@gmail.com>
Globally replace all occurances of WATCHDOG_RESET() with schedule(),
which handles the HW_WATCHDOG functionality and the cyclic
infrastructure.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Rini <trini@konsulko.com> [am335x_evm, mx6cuboxi, rpi_3,dra7xx_evm, pine64_plus, am65x_evm, j721e_evm]
This patch integrates the watchdog triggering into the recently added
cyclic infrastructure. Each watchdog device that shall be triggered
registers it's own cyclic function. This way, multiple watchdog devices
are still supported, each via a cyclic function with separate trigger
intervals.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Rini <trini@konsulko.com> [am335x_evm, mx6cuboxi, rpi_3,dra7xx_evm, pine64_plus, am65x_evm, j721e_evm]
When fixed offset via CONFIG_SYS_MMC_U_BOOT_OFFS is not specified then
expects that U-Boot proper is placed immediately after SPL without any
additional padding.
This allows to generate smaller SPL+U-Boot final binary as it is not
required to specify fixed offset to U-Boot proper at SPL compile time.
In this case offset to U-Boot proper is calculated at SPL compile time in
linker script.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
This allows to concatenate SPL and proper U-Boot without extra alignment.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
We currently have an if_type (interface type) and a uclass id. These are
closely related and we don't need to have both.
Drop the if_type values and use the uclass ones instead.
Maintain the existing, subtle, one-way conversion between UCLASS_USB and
UCLASS_MASS_STORAGE for now, and add a comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
These are currently using a simple array lookup in one direction, and
relying on if_type being sequential.
With the move to uclass IDs this needs to change. Update the code to
prepare for the new way. This patch is intended to introduce no
functional change.
The returning of "(none)" from blk_get_if_type_name() is handling a case
that should not happen in either case.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we use a variable with the same name as the enum. Change this
since we plan to #define the enum to uclass_id.
Signed-off-by: Simon Glass <sjg@chromium.org>
This doesn't seem to be used for anything and it isn't clear what it is.
It dates from the first U-Boot commit.
Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
We don't want boards to be able to change these. They can be handled
as dependencies of options that need them, such as SPL_MMC. There is no
point in enabling the block interface without any storage devices to
create a block device.
Hide both options from the 'menuconfig' display and deny their use in
defconfig files.
Signed-off-by: Simon Glass <sjg@chromium.org>
Selecting this option can be handled in the Kconfig option itself, as it
is with BLK. Update this an drop the various 'select' clauses.
Signed-off-by: Simon Glass <sjg@chromium.org>
This option is fact really related to SPL. For U-Boot proper we always use
driver model for block devices, so CONFIG_BLK is enabled if block devices
are in use.
It is only for SPL that we have two cases:
- SPL_BLK is enabled, in which case we use driver model and blk-uclass.c
- SPL_BLK is not enabled, in which case (if we need block devices) we must
use blk_legacy.c
Rename the symbol to SPL_LEGACY_BLOCK to make this clear. This is
different enough from BLK and SPL_BLK that there should be no confusion.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we use HAVE_BLOCK_DEVICE to indicate when block devices are
available.
This is a very strange option, since it partially duplicates the BLK
option used by driver model. It also covers both U-Boot proper and SPL,
even though one might have block devices and another not.
As a first step towards correcting this, create a new inline function
called blk_enabled() which indicates if block devices are available.
This cannot be used in Makefiles, or #if clauses, but can be used in C
code.
A function is useful because we cannot use CONFIG_IS_ENABLED(BLK) to
decide if block devices are needed, since we must consider the legacy
block interface, enabled by HAVE_BLOCK_DEVICE
Update a few places where it can be used and drop some unnecessary #if
checks around some functions in disk/part.c - rely on the compiler's
dead-code elimination instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present these files have an #ifdef covering the whole file. Move the
condition to the Makefile instead.
Add BLK to the condition since future patches will adjust things so that
HAVE_BLOCK_DEVICE is only for SPL, but the partition drivers are needed
in U-Boot proper too.
Signed-off-by: Simon Glass <sjg@chromium.org>
The _SUPPORT suffix should be dropped. This happened because the rename
was applied around the same time as this new option, so did not include
renaming the new option.
The relevant commits are:
f7560376ae sata: Rename SATA_SUPPORT to SATA
73059529b2 ata: ahci-pci: Add new option CONFIG_SPL_AHCI_PCI
Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Enable this option on all boards which support block devices. Drop the
related depencies on BLK since these are not needed anymore.
Disable BLOCK_CACHE on M5253DEMO as this causes a build error.
Signed-off-by: Simon Glass <sjg@chromium.org>
This allows to test if a pin's label if displayed using gpio_get_status()
when this pin is configured in alternate function.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Even pin with GPIOF_UNUSED function can have a label.
The criteria to add or not a space character is linked to label not to
the used/unused status.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The bar of the structure virtio_pci_cap is the index, and each base
address occupies 4 bytes, so it needs to be multiplied by 4.
This patch fixes a bug reported by Felix Yan
https://lists.denx.de/pipermail/u-boot/2022-August/492779.html
Signed-off-by: Xiang W <wxjstz@126.com>
Tested-by: Felix Yan <felixonmars@archlinux.org>
The nvme driver falsely assumed that the last entry on a page
of the prp-list always points to the next page of the prp-list.
This potentially can lead to the illegal creation of pages on
the prp-list with only a single entry. This change now ensures
that splitting the prp-list into multiple pages, behaves now as
required by the NVME-Spec.
Related to this, also the size of the memory allocation is adjusted
accordingly.
Signed-off-by: Alexander Sowarka <alexander.sowarka@aerq.com>
These two device tree properties were not being applied.
Fixes: 1fd9eb68d6 ("i2c: stm32f7: move driver data of each instance in a privdata")
Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Reviewed-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Tested-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Current function stm32_i2c_message_xfer is sending a STOP
whatever the result of the transaction is. This can cause issues
such as making the bus busy since the controller itself is already
sending automatically a STOP when a NACK is generated.
Thanks to Jorge Ramirez-Ortiz for diagnosing and proposing a first
fix for this. [1]
[1] https://lore.kernel.org/u-boot/20220815145211.31342-2-jorge@foundries.io/
Reported-by: Jorge Ramirez-Ortiz, Foundries <jorge@foundries.io>
Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Tested-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Functions stm32_i2c_message_start and stm32_i2c_handle_reload
both get a stop boolean indicating if the transfer should end with
a STOP or not. However no specific handling is needed in those
functions hence remove the parameter.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Comment within stm32_i2c_message_start is misleading, indicating
that AUTOEND bit is setted while it is actually cleared.
Moreover, the bit is actually never setted so there is no need
to clear it hence get rid of this bit clear and the bit macro
as well.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Bits should be set to 0, not 1.
Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Changes optee_rng driver to register itself has a OP-TEE service so
that a device is bound for the driver when OP-TEE enumerates the
PTA RNG service.
Cc: Sughosh Ganu <sughosh.ganu@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
This change defines resources for OP-TEE service drivers to register
themselves for being bound to when OP-TEE firmware reports the related
service is supported. OP-TEE services are discovered during optee
driver probe sequence which mandates optee driver is always probe once
bound.
Discovery of optee services and binding to related U-Boot drivers is
embedded upon configuration switch CONFIG_OPTEE_SERVICE_DISCOVERY.
Cc: Jens Wiklander <jens.wiklander@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Removes local variable child in optee_probe() that is not used.
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
The device tree binding [1] specify the vendor-id, product-id, device-id
and language-id as 16 bit values and the linux driver reads the boost-up
value as 8 bit value.
[1] https://www.kernel.org/doc/Documentation/devicetree/bindings/usb/usb251xb.txt
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Add functions to read 8/16-bit integers like the existing functions for
32/64-bit to simplify read of 8/16-bit integers from device tree
properties.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add ID for Winbond W25Q512JVQ device which is supported
on AST2600 EVB by default.
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Driver can configure the SPI clock frequnecy to the
target value of "spi-max-frequency" property in
the device tree. The frequency is divided from HCLK,
200MHz. Usually, the ASPEED SPI clock frequency range
is between 12.5MHz and 100MHz. On AST2600, the lowest
SPI clock frequency can be about 780kHz.
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
If "decoded-ranges" is defined in the device tree, the
driver will apply the decoded address ranges from this
property to the controller during probe stage.
This patch refers to the following OpenBMC u-boot patch.
https://patchwork.ozlabs.org/project/openbmc/list/?series=306969
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
There are some known HW problems about decoded
range register configurations on existing AST2500 and
AST2600 platforms. Additional callback function,
adjust_decoded_sz, is added to solve these problems
on each platform. Besides, aspeed_spi_trim_decoded_size
function is added to modify overall decoded address
size for fitting the maximum AHB decoded size.
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
From the HW point of view, the performance of
command read mode is greater than user mode slightly.
Thus, dirmap read framework is introduced to achieve
this goal. In dirmap_create, command read mode is
configured. Usually, the decoded address area with flash
size is assigned to each CS. CPU can thus access the
SPI flash as normal memory in dirmap_read function.
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
This adds support for the dirmap API to the spi-nor subsystem, as
introduced in Linux commit df5c21002cf4 ("mtd: spi-nor: use
spi-mem dirmap API").
This patch is synchronize from the following patch
https://patchwork.ozlabs.org/project/uboot/patch/20210205043924.149504-4-seanga2@gmail.com/
The corresponding Linux kernel SHA1 is df5c21002cf4.
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
This adds the dirmap API originally introduced in
Linux commit aa167f3fed0c
("spi: spi-mem: Add a new API to support direct mapping").
This also includes several follow-up patches and fixes.
Changes from Linux include:
* Added Kconfig option
* Changed struct device to struct udevice
* Changed struct spi_mem to struct spi_slave
This patch is obtained from the following patch
https://patchwork.ozlabs.org/project/uboot/patch/20210205043924.149504-3-seanga2@gmail.com/
The corresponding Linux kernel SHA1 is aa167f3fed0c.
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Although AST2400 is EOL officially, in order to achieve
sustainability and completeness, AST2400 part is added.
For AST2400,
- Five CSs are supported by FMC controller.
- SPI1 controller only supports single CS and there is
no address segment address register. The CE control
register of SPI1 is located at the offset 0x04 and
the 4-byte address mode control bit is bit 13 of
this register.
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Add ASPEED BMC FMC/SPI memory controller driver with
spi-mem interface for AST2500 and AST2600 platform.
There are three SPI memory controllers embedded in an ASPEED SoC.
- FMC: Named as Firmware Memory Controller. After AC on, MCU ROM
fetches initial device boot image from FMC chip select(CS) 0.
- SPI1: Play the role of a SPI Master controller. Or, there is a
dedicated path for HOST(X86) to access its BIOS flash mounted
under BMC. spi-aspeed-smc.c implements the control sequence when
SPI1 is a SPI master.
- SPI2: It is a pure SPI flash controller. For most scenarios, flashes
mounted under it are for pure storage purpose.
ASPEED SPI controller supports 1-1-1, 1-1-2 and 1-1-4 SPI flash mode.
Three types of command mode are supported, normal mode, command
read/write mode and user mode.
- Normal mode: Default mode. After power on, normal read command 03h or
13h is used to fetch boot image from SPI flash.
- AST2500: Only 03h command can be used after power on
or reset.
- AST2600: If FMC04[6:4] is set, 13h command is used,
otherwise, 03h command.
The address length is decided by FMC04[2:0].
- Command mode: SPI controller can send command and address
automatically when CPU read/write the related remapped
or decoded address area. The command used by this mode
can be configured by FMC10/14/18[23:16]. Also, the
address length is decided by FMC04[2:0]. This mode will
be implemented in the following patch series.
- User mode: It is a traditional and pure SPI operation, where
SPI transmission is controlled by CPU. It is the main
mode in this patch.
Each SPI controller in ASPEED SoC has its own decoded address mapping.
Within each SPI controller decoded address, driver can assign a specific
address region for each CS of a SPI controller. The decoded address
cannot overlap to each other. With normal mode and command mode, the
decoded address accessed by the CPU determines which CS is active.
When user mode is adopted, the CS decoded address is a FIFO, CPU can
send/receive any SPI transmission by accessing the related decoded
address for the target CS.
This patch only implements user mode initially. Command read/write
mode will be implemented in the following patches.
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Add FWSPICS1 and SPI1CS1 in AST2500 pinctrl group.
On AST2500 EVB, FWSPICS1 can be supported by default.
An extra jumper, J45, should be configured before
enabling SPI1CS1.
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
User can get correct HCLK frequency during driver probe stage
by adding the following configuration in the device tree.
"clocks = <&scu ASPEED_CLK_AHB>".
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Few lines are extented to next line though they can fit in 80 character
limit, align them to single line. No functional change.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20220825125906.11581-6-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
As the flash sizes are increasing day by day, QSPI can have devices of
size > 512MB. In qspi driver we are trying to read all the data at once
using DMA.
The DMA descriptor destination size is only 29bits long.
QSPIDMA_DST_SIZE 0xFF0F0804
BITS: 1:0 Reserved to keep word alignment
BITS: 28:2 Number of 4-byte words the DMA will transfer
BITS: 31:29 Reserved: Returns 0 when read, writes ignored
So we can only transfer data of 0x1FFFFFF0(512MB minus 4bytes) bytes.
Anything above will overflow this register and will ignore higher bits
above 29 bits.
Change the DMA functionality if the requested size is greater than or
equal to 512MB to read 256MB chunks.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20220825125906.11581-5-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add support for io-mode transfers. This is necessary for UBIFS to work
properly with spi-nor devices. The driver will work in IO mode when
"has-io-mode" is passed from device tree instead of DMA.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20220825125906.11581-4-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
As per driver model we should enumerate plat structure only in
of_to_plat() and should be used only in probe(). Copy required
plat structure info into priv structure in probe() and use priv
structure across the driver. So replace plat with priv structure across
the driver.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/20220824113847.7482-4-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
In cadence_spi_read_id we are using STIG mode to read flash id's.
Call cadence_qspi_apb_command_read_setup() to setup cmd, addr and data
bus width properly before cadence_qspi_apb_command_read().
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/20220824113847.7482-3-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
In cadence_spi_probe, cadence_qspi_versal_flash_reset() is called to reset
the flash device. Looks like there is a mistake in previous series of
patches where it is defined as cadence_spi_versal_flash_reset() but
called as cadence_qspi_versal_flash_reset. Since there is a weak function
defined with the same name this issue was not caught.
Fix the issue by renaming cadence_spi_versal_flash_reset as
cadence_qspi_versal_flash_reset().
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/20220824113847.7482-2-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Check snprintf() return value for errors.
Make microblaze_cpu_get_desc() directly return snprintf() error code if
ret < 0. Otherwise, if the return value is greater than or equal to size,
the resulting string is truncated, so return -ENOSPC.
Fixes: 816226d27e ("cpu: add CPU driver for microblaze")
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Link: https://lore.kernel.org/r/20220829170205.1274484-2-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
The drivers informs the user that a post config was not run after FPGA
configuration. This message is unnecessary in SPL because the
ps7_post_config function is called via spl_board_prepare_for_boot
function before jump_to_image_no_args function from board_init_r
function.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Link: https://lore.kernel.org/r/20220808145331.24723-1-stefan.herbrechtsmeier-oss@weidmueller.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Move arm twd timer driver from zynq to generic location.
DM timer drivers are designed differently to original driver. Timer is
counting up and not down.
Information about clock rates are find out in timer_pre_probe() that's
why there is no need to get any additional information from DT in the
driver itself (only register offset).
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Link: https://lore.kernel.org/r/20220805061629.1207-1-stefan.herbrechtsmeier-oss@weidmueller.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
- remove test on CONFIG_DM_REGULATOR in stm32mp1 board
and enable CONFIG_DM_REGULATOR for stm32f769-disco
- handle ck_usbo_48m clock provided by USBPHYC to fix the command 'usb start'
after alignment with Linux kernel v5.19 DT (clocks = <&usbphyc>)
- Fix SYS_HZ_CLOCK value for stih410-b2260 board
- Switch STMM32MP15x DHSOM to FMC2 EBI driver
- Remove hwlocks from pinctrl in STM32MP15x to avoid issue with kernel
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAmMZoW4ACgkQ4rK92eCq
k3W2MAgAsmy2aSlMYo/AGlJ/KCrZuk6OirNHtdOdacvbcdUUbpkNpBSjdkrRm2If
VUnY1utIIJe6gFgnBUxXJ3RF5FZuhkdawc6V25HtDp6H3WamzJknKs5Vc4TlKp59
hZCOto7/+G/cd2XLdCKFUBl+new1pdDPsEm56+57DeZ7QGAQRX35PUQ5+HBjQJ/N
n/wJgS6wkEdIQLLwmCVxbHUkC+pRotTza5F2A0qZJgYPMcMpVFYKtzIa4GbWB5YS
MKGHbM8f3C8RLPQaHHTRycoA2Yor1I52B4Oi7605c5zHQr9pjrgtWsernDzkIhsB
ThYHSYQBUBTY4HBfzFwzCkVGqqLWNg==
=PMFY
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20220907' of https://source.denx.de/u-boot/custodians/u-boot-stm
- simplify the STM32MP15x package parsing code
- remove test on CONFIG_DM_REGULATOR in stm32mp1 board
and enable CONFIG_DM_REGULATOR for stm32f769-disco
- handle ck_usbo_48m clock provided by USBPHYC to fix the command 'usb start'
after alignment with Linux kernel v5.19 DT (clocks = <&usbphyc>)
- Fix SYS_HZ_CLOCK value for stih410-b2260 board
- Switch STMM32MP15x DHSOM to FMC2 EBI driver
- Remove hwlocks from pinctrl in STM32MP15x to avoid issue with kernel
Fman microcode is executable code (AFAICT) loaded into a
coprocessor. As such, if verified boot is enabled, it must be verified
like other executable code. However, this is not currently done.
This commit adds verified boot functionality by encapsulating the
microcode in a FIT, which can then be signed/verified as normal. By
default we allow fallback to unencapsulated firmware, but if
CONFIG_FIT_SIGNATURE is enabled, then we make it mandatory. Because
existing Layerscape do not use this config (instead enabling
CONFIG_CHAIN_OF_TRUST), this should not break any existing boards.
An example (mildly-abbreviated) its is provided below:
/ {
#address-cells = <1>;
images {
firmware {
data = /incbin/(/path/to/firmware);
type = "firmware";
arch = "arm64";
compression = "none";
signature {
algo = "sha256,rsa2048";
key-name-hint = "your key name";
};
};
};
configurations {
default = "conf";
conf {
description = "Load FMAN microcode";
fman = "firmware";
};
};
};
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Several ethernet drivers load firmware from FIT images. Convert them to
use the fit_get_data helpers.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Handle the input clock of RCC USB_PHY_48, provided by USBPHYC
and named "ck_usbo_48m".
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
ck_usbo_48m is generated by usbphyc PLL and used by OTG controller
for Full-Speed use cases with dedicated Full-Speed transceiver.
ck_usbo_48m is available as soon as the PLL is enabled.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add the counter of the PLL user n_pll_cons managed by the 2 functions
stm32_usbphyc_pll_enable / stm32_usbphyc_pll_disable.
This counter allow to remove the function stm32_usbphyc_is_init
and it is a preliminary step for ck_usbo_48m introduction.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
System reset via the SRST extension in the SBI should be the default.
The driver checks if the extension is available when probing.
So there is no risk in enabling it.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
This commit sychronizes the header file for FU740 PRCI clocks with the
one from Linux 5.19.
The constant values are the same, but all constant names are changed
(most are just prefixed with FU740_).
Signed-off-by: Icenowy Zheng <uwu@icenowy.me>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
If ethernet connected to SFP, like this:
&enetc_port0 {
phy-connection-type = "sgmii";
sfp = <&sfp0>;
managed = "in-band-status";
status = "okay";
};
Then enetc_config_phy returns -ENODEV and the memory containing the mdio interface is freed.
It's better to unregister and free mdio resources.
Signed-off-by: Siarhei Yasinski <siarhei.yasinski@sintecs.eu>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
In both the Freescale DDR controller and the SPD spec, bank address bits
are stored as the number of bank address bits minus 2. For example, if a
chip had 8 banks (3 total bank address bits), the value of
bank_addr_bits would be 1. This is rather surprising for users
configuring their memory manually, since they can't set bank_addr_bits
to the actual number of bank address bits. Rectify this.
There is at least one example of this kind of mistake already, in
board/freescale/t102xrdb/ddr.c. The documented MT40A512M8HX has two bank
address bits, but bank_addr_bits was set to 2, implying 4 bank address
bits. Such a value is reserved in BA_BITS_CS, but I suspect the
controller simply ignores the top bit, making this kind of mistake
harmless, if misleading.
Fixes: e8a7f1c32b ("powerpc/t1023rdb: Add T1023 RDB board support")
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The interactive mode uses large several tables of options which can be
configured. However, much of the contents of these tables are
repetetive. For example, no struct is larger than half a kilobyte, so
the offset only takes up 9 bits. Similarly, the size is only ever 4 or
8, and printhex is a boolean. Reduce the size of these fields. This
reduces the size of the options tables by around 10 KiB. However, the
largest contributor to the size of the options tables is the use of a
pointer for the strings. A better approach would be to use a separate
array of strings, and store an integer index in the options tables.
However, this would require a large re-architecting of this file.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Adding some debug prints I can see:
MMC: mmc@fe320000: Got clock clock-controller@ff760000 76
mmc@fe310000: Got clock clock-controller@ff760000 77
Unknown clock 77
rockchip_dwmmc_get_mmc_clk: err=-2
mmc@fe310000: 3, mmc@fe320000: 1, mmc@fe330000: 0
According to kernel code the SDIO clock is identical to SDMMC clock
except for the con 16->15 change.
Add support for the clock to avoid the error.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Currently the default initialisation frequency is 50MHz. Although
this does appear to be suitable for some LPDDR4 RAM chips, training at
this low frequency has been seen to cause Column errors, leading to
Capacity check errors on others.
Here we force RAM initialisation to happen at 400MHz before ramping up
to the final value running value of 800MHz after everything has been
successfully configured.
Link: https://lore.kernel.org/u-boot/Yo4v3jUeHXTovjOH@google.com/
Suggested-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Tested-by: Xavier Drudis Ferran <xdrudis@tinet.cat>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Michal Suchánek <msuchanek@suse.de>
Frequency changes to 400MHz are presently reported as:
lpddr4_set_rate_0: change freq to 400000000 mhz 0, 1
This is obviously wrong by 6 orders of magnitude.
Ensure frequency changes are reported accurately.
Signed-off-by: Lee Jones <lee@kernel.org>
Tested-by: Xavier Drudis Ferran <xdrudis@tinet.cat>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Functions pointed to by this op pointer can return non-zero values
indicating an error. Ensure any error value is propagated back up the
call-chain.
Signed-off-by: Lee Jones <lee@kernel.org>
Tested-by: Xavier Drudis Ferran <xdrudis@tinet.cat>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Only add the dram channel when we finally setup it successfully at the
last step.
Signed-off-by: Han Pengfei <pengphei@foxmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add a vendor-specific TPM2 command for this and implement it for Cr50.
Note: This is not part of the TPM spec, but is a Cr50 extension.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
It is useful to read information about the current TPM state, where
supported, e.g. for debugging purposes when verified boot fails.
Add support for this to the TPM interface as well as Cr50. Add a simple
sandbox test.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
At present the emulator assumes that the TPM is inited in the same phase
where it is used. But in fact SPL may init the TPM, so we don't want to
complain when U-Boot proper later uses it. Remove this check.
It might be best to save this information into the device state for the
TPM, so that we can make sure the TPM was inited at some point. For now,
this seems good enough.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The host will report such error message if the fastboot device work in
full-speed mode: "Duplicate descriptor for config 1 interface 0
altsetting 0, skipping"
Fastboot device ack both full and high speed interface descriptors when
work in full-speed mode, that's will cause this issue.
Fix it.
Signed-off-by: qianfan Zhao <qianfanguijin@163.com>
Reviewed-by: John Keeping <john@metanate.com>
The compatible values used for device nodes representing Renesas Reduced
Pin Count Interfaces were based on preliminary versions of the Device
Tree Bindings.
Correct them in both DTSi files and drivers, to match the final DT
Bindings.
Note that there are no DT bindings for RPC-IF on RZ/A1 yet, hence the
most logical SoC-specific value is used, without specifying a
family-specific value.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The brute-force controller disable method can end up racing controller
initialization and causing a crash when we shut down Apple ANS2 NVMe
controllers. Do a proper controlled shutdown, which does block until
things are quiesced properly. This is nicer in general for all
controllers.
Signed-off-by: Hector Martin <marcan@marcan.st>
Tested-by: Mark Kettenis <kettenis@openbsd.org> (firefly-rk3399)
PCIe config space has address range 0-4095. So do not allow reading from
addresses outside of this range. Lot of U-Boot drivers do not expect that
passed value is not in this range. PCI DM read function is extended to
fill read value to all ones or zeros when it fails as U-Boot callers
ignores return value.
Calling U-Boot command 'pci display.b 0.0.0 0 0x2000' now stops printing
config space at the end (before 0x1000 address).
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
We can check if the message was acknowledged in the common
ti_sci_do_xfer() which lets us remove it from after each call to this
function. This simplifies the code and reduces binary size.
Signed-off-by: Andrew Davis <afd@ti.com>
The inline hint is not needed here, the compiler will do the right thing
based on if we are compiling for speed or for code size. In this case the
inline causes this function to be placed inside each callsite which is
not the right thing to do for either speed nor size. There is no
performance benefit to this due to the larger function size reducing
cache locality, but there is a huge size penalty. Remove inline keyword.
Signed-off-by: Andrew Davis <afd@ti.com>
We don't need to print the same message in every location, just
print it in the function that fails and remove all the extra
message printouts.
Signed-off-by: Andrew Davis <afd@ti.com>
This ti_sci_do_xfer() function already prints out the reason for the
failure, and the caller of each of these functions should also notify
the user of the failed task. Remove this extra level of error message.
Signed-off-by: Andrew Davis <afd@ti.com>
Currently for all Qcom SoCs/boards there are separate compatibles for
GPIO and pinctrl. But this is inconsistent with official (upstream) Linux
bindings which requires only a single compatible "qcom,<SoC name>-pinctrl"
and there is no such compatible property as "qcom,tlmm-<SoC name>".
So fix this inconsistency for Qcom SoCs in order to comply with upstream
DT bindings. This is done via removing compatibles from "msm_gpio" driver
and via binding to "msm_gpio" driver from pinctrl driver in case
"gpio-controller" property is specified for pinctrl node.
Suggested-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
GPIO LV (low voltage)/MV (medium voltage) subtypes have different
features and register mappings than 4CH/8CH subtypes. Add support
for LV and MV subtypes.
With GPIO LV/MV subtype available, add "qcom,pms405-gpio" compatible
which requires support for GPIO MV subtype.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Since both pm8916.c and pm8916_gpio.c are already supporting multiple
Qcom SoCs, it makes sense to rename these drivers to pmic_qcom.c and
qcom_pmic_gpio.c respectively. Also, these driver can be extended to
support additional functionality if required for other Qcom SoCs.
Along with this import latest DT binding: qcom,spmi-pmic.txt from Linux
kernel and thereby remove pm8916.txt.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Since the base functionality remains the same for a reset driver on Qcom
SoCs, so leverage that to convert ipq4019 specific reset driver to a
generic Qcom reset driver. With that one just need to provide SoC specific
reset table.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
QCS404 SoC supports two types of PHY, one supports high speed mode or
USB2 PHY and the other supports super speed mode or USB3 PHY. So add
corresponding PHY drivers.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Re-sync again on some linux part, add some fixes for fsl_elbc from
Pali and switch
imx8mn bsh to use nand base ident
For nand subsystem tested on:
- imx8mn Macronix MX30LF4G18AC
- P2020 based board Turris 1.1 for fsl_elbc
The gpio-button driver depends on DM_GPIO, add it to Kconfig to avoid
build errors.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Add timer support for Kirkwood and MVEBU devices.
Cc: Pali Rohár <pali@kernel.org>
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
During compilation gcc throws warning:
drivers/mtd/nand/raw/fsl_elbc_nand.c: In function ‘fsl_elbc_nand_probe’:
drivers/mtd/nand/raw/fsl_elbc_nand.c:841:31: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
return fsl_elbc_chip_init(0, (void *)dev_read_addr(dev), dev);
^
Fix it by using dev_read_addr_ptr() function which returns pointer instead
of dev_read_addr() which returns integer type.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Subpage write support for freescale eLBC NAND controller driver is
implemented in U-Boot and was fixes in the commit d3963721d9 ("nand: Sync
with Linux v4.1").
So remove NAND_NO_SUBPAGE_WRITE flag from the fsl_elbc_nand.c driver. This
partially revert commit cb04c77234 ("nand/fsl: add NAND_NO_SUBPAGE_WRITE
to eLBC and IFC drivers"), only eLBC driver part.
With this change U-Boot with default settings can read from NAND UBIFS
image created on Linux with Linux default settings. Prior this change
U-Boot was unable to read from NAND UBIFS images created with Linux default
settings due to differnet UBI geometry.
Linux kernel fsl_elbc_nand.c driver also does not set NAND_NO_SUBPAGE_WRITE
flag and has implemented subpage write support.
Fixes: cb04c77234 ("nand/fsl: add NAND_NO_SUBPAGE_WRITE to eLBC and IFC drivers")
Fixes: d3963721d9 ("nand: Sync with Linux v4.1")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Acked-By: Michael Trimarchi<michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Upstream linux commit 8fc82d456e40a0.
On some nand controllers with hw-ecc the controller code wants to know
the ecc strength and size and having these as 0, 0 is not accepted.
Specifying these in devicetree is possible but undesirable as the nand
may be different in different production runs of the same board, so it
is better to get this info from the nand id where possible.
This commit adds code to read the ecc strength and size from the nand
for Samsung extended-id nands. This code is based on the info for the 5th
id byte in the datasheets for the following Samsung nands: K9GAG08U0E,
K9GAG08U0F, K9GAG08X0D, K9GBG08U0A, K9GBG08U0B. These all use these bits
in the exact same way.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Upstream linux commit 7bb427990ee364.
Rename the function to match this new behavior.
NOTE: fix nand_detect/nand_get_flash_type parameters in
mxs_nand_spl. This code seems never executed by any board
as alternative for nand detect
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Upstream linux commit 4722c0e958e636.
The returned "type" is never used in nand_scan_ident() and spl code
Make nand_get_flash_type() simply return an integer value in order
to avoid unnecessary ERR_PTR/PTR_ERR dance.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Upstream linux commit 8cfb9ab68f9070.
Drop the 's' at the end of nand_manufacturers since the struct is actually
describing a single manufacturer, not a manufacturer table.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
The kmtegr1 board is out of maintenance and can be removed. As it is the
only board in the tree using MPC8309 the support for this CPU is dropped
completely.
Signed-off-by: Holger Brunck <holger.brunck@hitachienergy.com>
The deadline for DM_ETH migration passed 2 years ago. Now that
platforms which cannot be migrated have been either removed or had
drivers disabled, and platforms that needed minor help to migrate have
been forcefully migrated, we can complete the migration.
This entails select'ing DM_ETH under NETDEVICES, and then removing now
extraneous depends on lines. In a few places, we can now either remove
options or just simplify later dependencies.
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Ramon Fried <rfried.dev@gmail.com>
As this driver has been converted to DM_ETH and the migration deadline
is 2 years passed, remove the legacy code and callers.
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Ramon Fried <rfried.dev@gmail.com>
When using DM_ETH, which should be the default now, we need to always
have DM_MDIO and FSL_LS_MDIO enabled, so select them.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Cc: Wasim Khan <wasim.khan@nxp.com>
Cc: Udit Agarwal <udit.agarwal@nxp.com>
Cc: Ashish Kumar <Ashish.Kumar@nxp.com>
Cc: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Manish Tomar <Manish.Tomar@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This driver has not been converted to DM_ETH. The migration
deadline passed 2 years ago.
Cc: Trevor Woerner <twoerner@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Ramon Fried <rfried.dev@gmail.com>
This driver has not been converted to DM_ETH. The migration deadline
passed 2 years ago.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: David Feng <fenghua@phytium.com.cn>
Cc: Liviu Dudau <liviu.dudau@foss.arm.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Ramon Fried <rfried.dev@gmail.com>
This converts the following to Kconfig:
CONFIG_FSL_NGPIXIS
CONFIG_SYS_FSL_QMAN_V3
CONFIG_SYS_FSL_RAID_ENGINE
CONFIG_SYS_FSL_RMU
CONFIG_SYS_FSL_SINGLE_SOURCE_CLK
CONFIG_SYS_FSL_SRIO_LIODN
CONFIG_SYS_FSL_TBCLK_DIV
CONFIG_SYS_FSL_USB1_PHY_ENABLE
CONFIG_SYS_FSL_USB2_PHY_ENABLE
CONFIG_SYS_FSL_USB_DUAL_PHY_ENABLE
CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS
CONFIG_SYS_FSL_OTHER_DDR_NUM_CTRLS
And we remove the entries from the README for a number of already
converted items.
Signed-off-by: Tom Rini <trini@konsulko.com>
In generally it is not permitted to implement an ofnode function only for
flat tree or live tree. Both must be supported. Also the code for
live tree access should be in of_access.c rather than ofnode.c which is
really just for holding the API-conversion code.
Update ofnode_write_prop() accordingly and fix the test so it can work
with flat tree too.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present ofnode only works with a single device tree, for the most part.
This is the control FDT used by U-Boot.
When booting an OS we may obtain a different device tree and want to
modify it. Add some initial support for this into the ofnode API.
Note that we don't permit aliases in this other device tree, since the
of_access implementation maintains a list of aliases collected at
start-up. Also, we don't need aliases to do fixups in the other FDT. So
make sure that flat tree and live tree processing are consistent in this
area.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rename these to VESA, itself an abbreviation, to avoid a conflict with
Verified Boot for Embedded.
Rename this to avoid referencing VBE.
Signed-off-by: Simon Glass <sjg@chromium.org>
We want to use VBE to mean Verfiied Boot for Embedded in U-Boot. Rename
the existing VBE (Vesa BIOS extensions) to allow this.
Verified Boot for Embedded is documented doc/develop/vbe.rst
Signed-off-by: Simon Glass <sjg@chromium.org>
Commit 44645f87de ("mmc: Fix mmc_switch excessive timeout") introduced
a side effect where CMD13 SEND_STATUS is issued in case mmc_wait_dat0()
does not return -ENOSYS and $send_status is not set. This happens on all
hardware which does implement .mmc_wait_dat0 callback, e.g. i.MX8M .
This leads to lengthy timeout before booting OS in case of eMMC in one
of the HS200/HS400 modes, since the card cannot respond to CMD13 while
downgrading from HS200/HS400 to regular HS mode.
Fix this by adding the missing conditional.
Fixes: 44645f87de ("mmc: Fix mmc_switch excessive timeout")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Kirill Kapranov <kirill.kapranov@compulab.co.il>
Cc: Marek Behún <marek.behun@nic.cz>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Ye Li <ye.li@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Release PERST# signal via GPIO when "reset-gpios" is defined in device tree.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
In more cases group name consist of function name followed by function
number. So if function name is just prefix of group name, show group name.
So in 'pinmux status -a' command output would be visible also extended
function number, which is useful for debugging.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
All 3 MPP pins (20, 21 and 22) can be configured individually and also can
be configured to GPIO functions. Fix definitions for these MPP pins in
existing pin groups. After this change GPIO function can be enabled just
for one of these 3 pins.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
The last user of this driver was removed in commit dee08b1999 ("arm:
Remove gplugd board"). Remove the unused driver.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Pali Rohár <pali@kernel.org>
CMD_GENERAL_CONTROL takes two 8-bit arguments but CMD_EXT_CONTROL takes
two 16-bit arguments. Fix this issue and change CMD_EXT_CONTROL arguments
to 16-bit.
Fixes: 5e4d24ccc1 ("gpio: Add Turris Omnia MCU driver")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This allows you to specify the type of rgmii-id that will enable phy
internal delay in ethernet phy-mode.
This adds all RGMII cases to all of get_pinmode() except LD11, because LD11
SoC doesn't support RGMII due to the constraint of the hardware. When RGMII
phy mode is specified in the devicetree for LD11, the driver will abort
with an error.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
We check if phydev is NULL. Only but if it is non-NULL we set one
component of phydev. But even if it is NULL we set another. We should not
dereference NULL in either case.
Fixes: e24b58f5ed ("net: phy: don't require PHY interface mode during PHY creation")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Reorder include files in the U-Boot expected order.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The convinience functions are not that small and they caused
bloated text segments because of their usage.
There was no need to inline them in the first place, as
they're not part of a fastpath.
Signed-off-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Previously we'd been using a device name retrieved via
ftgmac100_data->phydev, but the mdio read/write functions may be
called before that member is initialized in ftgmac100_phy_init(),
leading to a NULL pointer dereference while printing the error message
issued if the mdio access fails. We can instead use bus->name, which
is already available at that point.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Fixes: 538e75d3fc ("net: ftgmac100: add MDIO bus and phylib support")
Reviewed-by: Cédric Le Goater <clg@kaod.org>
NPCM750 provides identical ethernet MAC controllers for WAN/LAN applications.
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Only two boards in the tree set the macro DWC_NET_PHYADDR. Both have
CONFIG_DM_ETH_PHY=y, so should set the phy address in DT if necessary.
The imx8mp_evk does set the correct address in device tree.
The other board seems to be a copy-paste-adapt from an old
version of the imx8mp_evk config header, given the "#ifdef
CONFIG_DWC_ETH_QOS" block that has been removed from imx8mp_evk header
in commit 127fb45495. Its device tree doesn't even enable (i.e., set
'status = "okay"') the &eqos node. But the other ethernet device,
&fec, does get enabled, and does have a phy sitting at address 4 (and
it also has a corresponding legacy #define CONFIG_FEC_MXC_PHYADDR
4). So I believe it should be completely safe to remove it from there
as well.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
[trini: Re-apply to top of tree, update imx93_evk.h]
Signed-off-by: Tom Rini <trini@konsulko.com>
I have an iMX8MP with a ti,dp83867 phy in front of the eqos
interface. The phy is Gbit capable - however, the C and D differential
pairs are not physically routed to the RJ45 connector. So I need to
prevent the phy from advertising 1000Mbps.
The necessary code is almost already there in the form of a
phy_set_supported() call in eqos_start(), but the max-speed DT
property is currently only parsed in
eqos_probe_resources_stm32(). Lift that parsing to eqos_probe().
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Not only does eqos_remove() fail to free the buffers that have been
allocated by eqos_probe_resources_core(), it repeats those allocations
and thus drops twice as much memory on the floor.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Assign packet pointer only in case the MAC reports anything in the FIFO.
In case the MAC indicates empty FIFO, return 0 to pass that information
to the network stack.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
This patch adds basic support for the Marvell 88E1240 PHY.
This will be used by the upcoming ethernet support addition for the
Marvell MIPS Octeon EBB7304 platform.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
This patch adds support for the "marvell,reg-init" DT property, which
is used to describe board specific Marvell PHY register configurations
in the board dts file. This DT property is supported in the Linux Kernel
since a longer time. Adding it to U-Boot now, enables the boards which
describe the register settings in their DT files here as well.
I've included calling this marvell_of_reg_init() to all foo_config()
functions in this patch as well. If CONFIG_DM_ETH is not set, there is
no ofnode, or no "marvell,reg-init" property, the PHY initialization is
unchanged.
The function marvell_of_reg_init() is a port of the Linux version.
Please note that I explicitly did not add error checking and handling
to the U-Boot version, as this is basically not done for phy_read/write
in this Marvell PHY code.
This will be used by the upcoming ethernet support on the MIPS
Octeon EBB 7304 board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
A large number of files include <flash.h> as it used to be how various
SPI flash related functions were found, or for other reasons entirely.
In order to migrate some further CONFIG symbols to Kconfig we need to
not include flash.h in cases where we don't have a NOR flash of some
sort enabled. Furthermore, in cases where we are in common code and it
doesn't make sense to try and further refactor the code itself in to new
files we need to guard this inclusion.
Signed-off-by: Tom Rini <trini@konsulko.com>
As the only pic32 platform does not enable flash, this is dead code.
Remove it.
Cc: Purna Chandra Mandal <purna.mandal@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_FLASH_ERASE_TOUT
CONFIG_SYS_FLASH_LOCK_TOUT
CONFIG_SYS_FLASH_UNLOCK_TOUT
CONFIG_SYS_FLASH_WRITE_TOUT
In practice, for two m68k platforms we move to hard-coding with a
comment the timeout values, rather than try and make convoluted Kconfig
logic. We add options for the write and erase options to the pic32
flash driver, as this driver does make use of them. Everywhere else
these are unreferenced values.
Signed-off-by: Tom Rini <trini@konsulko.com>
Since commit 83061dbd1c ("Rename GPIO_SUPPORT to GPIO"),
SPL_GPIO_SUPPORT has been renamed to SPL_GPIO, meaning that SPL_GPIO_HOG
can never be enabled.
Let's fix this by using the proper name for the Kconfig option.
Fixes: 1d99e673c7 ("gpio: Enable hogging support in SPL")
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Some setups do not use Xen hypervisor console for logging, e.g. they
use emulated PL011 hardware or shared peripherals (real UART). In such
cases Xen HVC will be disabled on a build time and will cause issues in
current driver implementation.
This commit fixes build issues in Xen event channel driver, caused
by absense of console event channel, that is not available when console
config is disabled. Now console related code will be removed when
Xen HVC is turned off.
Signed-off-by: Dmytro Firsov <dmytro_firsov@epam.com>
Reviewed-by: Anastasiia Lukianenko <vicooodin@gmail.com>
Reviewed-by: Anastasiia Lukianenko <vicooodin@gmail.com<mailto:vicooodin@gmail.com>>
Signed-off-by: Dmytro Firsov <dmytro_firsov@epam.com<mailto:dmytro_firsov@epam.com>>
To work correctly, this driver depends on SYSCON to get the base address
from the parent dts node.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Reviewed-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
The TPM device comes with the random number generator(RNG)
functionality which is built into the TPM device. Add logic to add the
RNG child device in the TPM uclass post probe callback.
The RNG device can then be used to pass a set of random bytes to the
linux kernel, need for address space randomisation through the
EFI_RNG_PROTOCOL interface.
No compatible string is provided because this is not available in
the binding defined by Linux. If multiple rand devices are in the
system, then some method of selecting them (other than device tree)
will need to be used, or a binding will need to be added.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The TPM device has a builtin random number generator(RNG)
functionality. Expose the RNG functions of the TPM device to the
driver model so that they can be used by the EFI_RNG_PROTOCOL if the
protocol is installed.
Also change the function arguments and return type of the random
number functions to comply with the driver model api.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Linux kernel uses compatible string "marvell,armada370-nand-controller" for
nand controllers on Armada 370/XP/38x. U-Boot currently uses mix of
"marvell,armada370-nand" and "marvell,mvebu-pxa3xx-nand".
So unify it and use just Linux kernel compatible string.
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Stefan Roese <sr@denx.de>
This driver registers GPIO controller and allows U-Boot to control GPIO
pins on MCU which is connected to Turris Omnia via i2c.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Current pin control driver applies SDHCI PHY MUX selection
when board DT calls for eMMC function on MPP wires.
However, for CP side eMMC, only the "armada-8k-cpm-pinctrl"
compatibility string is taken into account, which causes
CP-SDHCI on Armada-7K boards to fail.
This patch adds "armada-7k-pinctrl" compatibility string
handling for the CP-SDHCI PHY configuration case.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
These functions are required for 'pinmux status -a' command to print
current configuration of each MPP pin.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
To automatically enable GPIO functionality of some MPP pin, it is required
to implement .gpio_request_enable and .gpio_disable_free callbacks in
pinctrl driver and set .request and .rfree callbacks in GPIO driver to
pinctrl_gpio_request / pinctrl_gpio_free functions.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Currently bank name is just one alphabetical letter.
Change it to mvebu and number.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Device tree property "ngpios" contains number of gpios.
Use it when available.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
To use particular pin GPIO, it needs to be first switched to GPIO by
pinctrl. Use pinctrl_gpio_request() and pinctrl_gpio_free() for this
purpose.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This change allows to use pinctrl_gpio_request() function as a direct
pointer for dm_gpio_ops's .request callback.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This new Armada 38x driver is based on Linux kernel driver. It can set any
pin to any valid function specified in DT like Linux kernel, it provides
support for 'pinmux status -a' command and also for pinctrl_gpio_request().
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This new function pinctrl_generic_set_state_prefix() behaves like
pinctrl_generic_set_state() but it takes third string argument which is
used as the prefix for each device tree string property.
This is needed for Marvell pinctrl drivers, becase Linux device tree files
have pinmux properties prefixed by "marvell," string.
This change allows to use generic U-Boot pinctrl functions for Armada 38x
pinctrl driver without need to copy+paste of the majority U-Boot pinctrl
code.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
start of test for fdt command
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmLgRtERHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreYXFwgAlALOMj3bwwsIAXNa5j/hPb3j/ecIqXgn
ocyxN+U5eSb2Ju5Jc9QmSeUMnGrii9+PW9j0JApdHrbUgBI2Sx+zwqMTIfA+BS05
4xXZgk5jOT+we2489FjgFcplv+dIuVlsB/Zo6zTbZyjkobfilYsZEGYHJ/CYNaIH
n7EmZeby1cXL7DMCxT39d3hD43XSX8cqQ1IIiF9DgtHQYs2Ff8dFcbWArSdgLX3o
Eob2Qj/GjScg87zjZcsgZajWJMHUfMeD5ZiKN2fR0T/wOdO1WtzFoF2Mt8KZcW1j
BD1shgBCMSSl5EgRG1BQZw4Sa92W2IBlbJ9tfIh8qnWOzEBzOs/M6w==
=lsO4
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-26jul22' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm.git
minor dm- and fdt-related fixes
start of test for fdt command
sandbox_defconfig builds the PCI MMC driver. It should be possible to
build the sandbox without ACPI support.
ACPI support in the PCI MMC driver is only needed when creating an ACPI
table. Fix building with ACPIGEN=n.
Fixes: dba7ee419d ("acpi: mmc: Generate ACPI info for the PCI SD Card")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add features to write protect single boot area rather than all boot
areas.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Only newer eSDHC controllers set PRSSTAT_SDSTB flag. So do not wait until
flag PRSSTAT_SDSTB is set on old pre-2.2 controllers. Instead sleep for
fixed amount of time like it was before commit 6f883e501b ("mmc:
fsl_esdhc: Add emmc hs200 support").
This change fixes error 'Internal clock never stabilised.' which is printed
on P2020 board at every access to SD card.
Fixes: 6f883e501b ("mmc: fsl_esdhc: Add emmc hs200 support")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
In order to have the possibility to configure the regulators at system
startup through DM support, all LDOs and bucks must be able to be
changeable. Currently there is a limitation to change the values when
the output is enabled. Since the driver is based on the ROHM BD71837 and a
comment that describes a limitation about switching while the output is
enabled can also be found there, the limitation probably comes from this type.
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
By reading binman symbols, we no need hard coded IMEM_LEN/DMEM_LEN after
we update the binman dtsi to drop 0x8000/0x4000 length for the firmware.
And that could save binary size for many KBs.
Tested-by: Tim Harvey <tharvey@gateworks.com> #imx8m[m,n,p]-venice
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
[Alper: Check BINMAN_SYMS_OK instead]
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Since new atheros PHY driver needs to access its PHY node through
phy device, we have to assign the phy node in ethernet controller
driver. Otherwise the PHY driver will fail to get some nodes
and properties.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Move i.MX code to a standalone file to make it easy for adding new
platform support
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Move macros and structures to header file and make some functions
public, so that could used by other files, this is to
prepare split platform specific config to one file.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When CONFIG_CLK is not enabled, there will be buil break:
"error: ‘eqos’ undeclared (first use in this function)"
Take eqos definition out the CONFIG_CLK ifdef.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add Kconfig for enabling reference events counter in DDRC performance
monitor by default
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Since i.MX9 uses same DDR PHY with i.MX8M, split the DDRPHY to a common
directory under imx, then use dedicated ddr controller driver for each
iMX9 and iMX8M.
The DDRPHY registers are space compressed, so it needs conversion to
access the DDRPHY address. Introduce a common PHY address remap function
for both iMX8M and iMX9 for all PHY registers accessing.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Sentinel have read access of OTP shadow register 0-511, and fsb have
read access of shadow 0-51/312-511.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
i.MX93 fuse can be accessed through FSB and s400-api. Add mapping tables
for i.MX93. The offset address of FSB accessing OTP shadow registers is
different between i.MX8ULP and i.MX93, so use macro to define the offset
address instead of hardcode.
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The i.MX93 platform wants to reuse drivers/misc/imx8ulp/fuse.c. Moving
fuse.c from the folder imx8ulp to sentinel makes it can be used by other
platforms.
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Introduce Sentinel API ahab_release_m33_trout to make sure sentinel
release M33 trout and make sure M33 could boot.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
To support more RDC instances on i.MX93, update API to latest
definition.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Since iMX9 uses S401 which shares the API with iMX8ULP. So move S400
MU driver and API to a common place and selected by CONFIG_IMX_SENTINEL
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Replace logically correct word in the description.
Fixes: 91a91ff804 ("dm: Add Kconfig options for driver model SPL support")
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Reviewed-by: Simon Glass <sjg@chromium.org>
If parameter drv of lists_bind_fdt() is specified, we shall bind only to
this very driver and to no other.
If the driver drv has an of_match property, we shall only bind to the
driver if it matches the compatible string of the device.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
If parameter drv of lists_bind_fdt() is specified, we want to bind to this
specific driver even if its field of_match is NULL.
If entry->of_match is NULL, we should not dereference it in a debug
statement.
Fixes: d3e773613b ("dm: core: Use U-Boot logging instead of pr_debug()")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When programming qspi flash speed we need to check the requested flash
speed not to exceed the spi max frequency. In the current implementation
we are checking qspi ref clk instead. This commit fixes the issue by
checking the requested speed and programs the specified max frequency.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/1657893679-20039-5-git-send-email-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add support_ops function zynq_qspi_mem_exec_op to check controller
supported operations by spi-mem framework. Current default support ops
function does not allow dummy buswidth no more than 1, unless we are
using buswidth is 4 for TX.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/1657893679-20039-4-git-send-email-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Fix dummy bytes calculation incase of valid dummy bytes when dummy
buswidth is > 1. Current dummy bytes calculation does not provide
correct dummy values for dummy buswidth > 1.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/1657893679-20039-3-git-send-email-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add child pre probe function in the driver. Update max_hz of priv from
spi_slave structure.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/1657893679-20039-2-git-send-email-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add support_ops function to check controller supported operations by
spi-mem framework. Current default support ops function does not allow
dummy buswidth no more than 1, unless we are using buswidth is 4 for TX.
In order to support dummy buswidth > 1 by spi-nor framework we are adding
explicit support_ops to check controller supported operations.
Fix dummy bytes calculation incase of valid dummy bytes when dummy
buswidth is > 1. Current dummy bytes calculation does not provide
correct dummy values for dummy buswidth > 1.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/1657954727-31972-3-git-send-email-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add support for spi memory operations for xilinx AXI qspi driver.
This provides an high-level interface to execute SPI memory
operations by the controller.
Remove existing spi transfer based implementation and use
spi memory based exec_op() implementation for qspi IO operations.
Simplified existing startup_block implementation.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/1657954727-31972-2-git-send-email-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add supporting new compatible string "u-boot,zynqmp-fpga-enc" to
handle loading encrypted bitfiles.
This feature requires encrypted FSBL, as according to UG1085:
"The CSU automatically locks out the AES key, stored in either BBRAM
or eFUSEs, as a key source to the AES engine if the FSBL is not
encrypted. This prevents using the BBRAM or eFUSE as the key source
to the AES engine during run-time applications."
Signed-off-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Co-developed-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Tested-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Link: https://lore.kernel.org/r/20220722141614.297383-14-oleksandr.suvorov@foundries.io
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reduce the function code by calling xilinx_pm_request() once only.
Use the same variable bsize_req to store either bstream size in bytes
or an address of bstream size according to a type required by the
firmware version. Remove obsolete debug().
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Tested-by: Ricardo Salveti <ricardo@foundries.io>
Tested-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Link: https://lore.kernel.org/r/20220722141614.297383-11-oleksandr.suvorov@foundries.io
Signed-off-by: Michal Simek <michal.simek@amd.com>
These flags may be used to check whether an FPGA driver is able to
load a particular FPGA bitstream image.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Tested-by: Ricardo Salveti <ricardo@foundries.io>
Tested-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Link: https://lore.kernel.org/r/20220722141614.297383-10-oleksandr.suvorov@foundries.io
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add a "compatible" string to binary flag converter, which uses
a callback str2flag() of given FPGA driver if available.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Tested-by: Ricardo Salveti <ricardo@foundries.io>
Tested-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Link: https://lore.kernel.org/r/20220722141614.297383-8-oleksandr.suvorov@foundries.io
Signed-off-by: Michal Simek <michal.simek@amd.com>
These flags may be used to check whether an FPGA driver is able to
load a particular FPGA bitstream image.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Tested-by: Ricardo Salveti <ricardo@foundries.io>
Tested-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Link: https://lore.kernel.org/r/20220722141614.297383-7-oleksandr.suvorov@foundries.io
Signed-off-by: Michal Simek <michal.simek@amd.com>
This flag is used to check whether a Xilinx FPGA driver is able to
load a particular FPGA bitstream image.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Tested-by: Ricardo Salveti <ricardo@foundries.io>
Tested-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Link: https://lore.kernel.org/r/20220722141614.297383-6-oleksandr.suvorov@foundries.io
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add a call to convert FPGA "compatible" string to a binary flag.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Tested-by: Ricardo Salveti <ricardo@foundries.io>
Tested-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Link: https://lore.kernel.org/r/20220722141614.297383-5-oleksandr.suvorov@foundries.io
Signed-off-by: Michal Simek <michal.simek@amd.com>
It allows using this feature without enabling the "fpga loads"
command.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Co-developed-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Signed-off-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Tested-by: Ricardo Salveti <ricardo@foundries.io>
Tested-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Link: https://lore.kernel.org/r/20220722141614.297383-2-oleksandr.suvorov@foundries.io
Signed-off-by: Michal Simek <michal.simek@amd.com>
After commit 8cca60a2cb ("Kconfig: Remove some symbols from the
whitelist") downstream builds failed for boards setting this in
include/configs/…
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Link: https://lore.kernel.org/r/20220721133122.32428-2-ada@thorsis.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Enable power domain driver to configure pmufw config object and request
node for all the IP's that are enabled in DT.
This driver depends on mailbox and IPI driver, hence enable them as well.
Add ARCH_VERSAL in the depends on of mailbox Kconfig to compile for
Versal platforms.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20220722084658.30995-6-ashok.reddy.soma@xilinx.com
Mailbox driver might be need for Versal and other future platforms.
To remove the dependency, move struct zynqmp_ipi_msg to
zynqmp_firmware.h so that mailbox driver compiles for other platforms
easily.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20220722084658.30995-5-ashok.reddy.soma@xilinx.com
Try loading pmufw config overlay for core0, if it doesn't return any
error it means pmufw is accepting nodes for other IP's. Otherwise dont
try to load config object for any other IP, just return from
zynqmp_pmufw_node function.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20220722084658.30995-3-ashok.reddy.soma@xilinx.com
zynqmp_pmufw_load_config_object() has some error cases and it is better
to return those errors. Change prototype of this function to return
errors.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20220722084658.30995-2-ashok.reddy.soma@xilinx.com
Add support for versal platform by adding "xlnx,versal-reset"
compatible string in zynqmp-reset driver. Reset numbering schema
for versal is not same as zynqmp, so nr_reset and reset_id are
set to zero. In case of assert/dessert, required device reset id
is sent from respective driver through struct reset_ctl.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@amd.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/20220720095959.29610-2-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Since the calulation of "bgen" is rounded down, using a higher
baudrate will result in a larger difference from the actual
baudrate. Should use DIV_ROUND_CLOSEST() like the Linux driver.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/1657676339-6055-1-git-send-email-hayashi.kunihiko@socionext.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Timing macro's are wrong for MMC_HS_52 and MMC_DDR_52. Fix it with
correct values of MMC_TIMING_MMC_HS and MMC_TIMING_MMC_DDR52 respectively.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/1656319965-12124-1-git-send-email-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
This commit fixes issue with usage of Xen hypervisor shared info page.
Previously U-boot did not unmap it at the end of OS boot process. Xen
did not prevent guest from this. So, it worked, but caused wierd
issues - one memory page, that was returned by memalign in U-boot
for Enlighten mapping was not unmaped by Xen (shared_info values was
not removed from there) and returned to allocator. During the Linux
boot, it uses shared_info page as regular RAM page, which leads to
hypervisor shared info corruption.
So, to fix this issue, as discussed on the xen-devel mailing list, the
code should:
1) Unmap the page
2) Populate the area with memory using XENMEM_populate_physmap
This patch adds page unmapping via XENMEM_remove_from_physmap, fills
hole in address space where page was mapped via XENMEM_populate_physmap
and return this address to memory allocator for freeing.
Signed-off-by: Dmytro Firsov <dmytro_firsov@epam.com>
Reviewed-by: Anastasiia Lukianenko <vicooodin@gmail.com>
The first AM6x device was the AM654x, but being the first we named it
just AM6, since more devices have come out with this same prefix we
should switch it to the normal convention of using the full name of the
first compatibility device the series. This makes what device we are
talking about more clear and matches all the K3 devices added since.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
For SDCC version 5.0.0, MCI registers are removed from SDCC interface
and some registers are moved to HC. So add support to use the new
compatible string "qcom,sdhci-msm-v5". Based on this new msm variant,
pick the relevant variant data and use it to detect MCI presence thereby
configuring register read/write to msm specific registers.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
"apple,t8112-dart" uses an incompatible register interface but still
offers the same functionality. This DART is found on the M2 and M1
Pro/Max/Ultra SoCs.
Signed-off-by: Janne Grunau <j@jannau.net>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
The imx6q arm2 board support has been removed from U-Boot
as it did not get converted to DM.
Remove the MX6Q_ARM2 related ifdefery in the driver.
Signed-off-by: Fabio Estevam <festevam@denx.de>
In preparation of re-sync of mtd stack, we opt to move the current stack
slowly in order to have a more easy sync and test. We would like to
prepare uboot to support no-jedec and no-onfi compliant nand so we need
to clean up a bit the code we have now and upstream some of the support.
In this series we expect no functional change
Tested on:
- imx6ull Micron MT29F2G08ABAGAH4
- imx8mn Macronix MX30LF4G18AC
Upstream linux commit f7025a43a9da26.
The MTD subsystem has its own small museum of ancient NANDs in a form of
the CONFIG_MTD_NAND_MUSEUM_IDS configuration option. The museum contains
stone age NANDs with 256 bytes pages, as well as iron age NANDs with 512
bytes per page and up to 8MiB page size.
It is with great sorrow that I inform you that the museum is being
decommissioned. The MTD subsystem is out of budget for Kconfig options and
already has too many of them, and there is a general kernel trend to
simplify the configuration menu.
We remove the stone age exhibits along with closing the museum
REMARK Don't apply this part from upstream:
Some of the iron age ones are transferred to the regular NAND depot.
Namely, only those which have unique device IDs are transferred, and the
ones which have conflicting device IDs are removed.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Upstream linux commit fb3bff5b407e58.
This patch enables support to read the ECC strength and size from the
NAND flash using Toshiba Memory SLC NAND extended-ID. This patch is
based on the information of the 6th ID byte of the Toshiba Memory SLC
NAND.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Upstream linux commit 3b5206f4be9b65.
Move Macronix specific initialization logic into nand_macronix.c. This
is part of the "separate vendor specific code from core" cleanup
process.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Upstream linux commit 229204da53b31d.
Move AMD/Spansion specific initialization/detection logic into
nand_amd.c. This is part of the "separate vendor specific code from
core" cleanup process.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Upstream linux commit 10d4e75c36f6c1.
Move Micron specific initialization logic into nand_micron.c. This is
part of the "separate vendor specific code from core" cleanup process.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Upstream linux commit 9b2d61f80b060c.
Move Toshiba specific initialization and detection logic into
nand_toshiba.c. This is part of the "separate vendor specific code from
core" cleanup process.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Upstream linux commit 01389b6bd2f4f7.
Move Hynix specific initialization and detection logic into
nand_hynix.c. This is part of the "separate vendor specific code from
core" cleanup process.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Upstream linux commit c51d0ac59f2420.
Move Samsung specific initialization and detection logic into
nand_samsung.c. This is part of the "separate vendor specific code from
core" cleanup process.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
In preparation of moving specific nand support that are not jedec
or onfi
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
nand_get_flash_type was reworked in commit 1ca6f9483e. This change
break the Mediatek MT721. Fix it adjust the function call parameters
+include/linux/mtd/rawnand.h:32:62: note: expected 'struct nand_chip *' but argument is of type 'struct mtd_info *'
+ 32 | struct nand_flash_dev *nand_get_flash_type(struct nand_chip *chip,
+ | ~~~~~~~~~~~~~~~~~~^~~~
+drivers/mtd/nand/raw/mt7621_nand.c:1189:48: error: passing argument 2 of 'nand_get_flash_type' from incompatible pointer type [-Werror=incompatible-pointer-types]
+ | ^~~~
+ | |
+ | struct nand_chip *
+include/linux/mtd/rawnand.h:33:49: note: expected 'int *' but argument is of type 'struct nand_chip *'
+ 33 | int *maf_id, int *dev_id,
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
chip points to mtd. Passing chip is enough to have a reference
to mtd when is necessary
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Upstream linux commit abbe26d144ec22.
A lot of NANDs are implementing generic features in a non-generic way,
or are providing advanced auto-detection logic where the NAND ID bytes
meaning changes with the NAND generation.
Providing this vendor specific initialization step will allow us to get
rid of full-id entries in the nand_ids table or all the vendor specific
cases added over the time in the generic NAND ID decoding logic.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Upstream linux commit 7f501f0a72036d.
Store the NAND ID in struct nand_chip to avoid passing id_data and id_len
as function parameters.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Upstream linux commit 29a198a1592d83.
Auto-detection functions are passed a busw parameter to retrieve the actual
NAND bus width and eventually set the correct value in chip->options.
Rework the nand_get_flash_type() function to get rid of this extra
parameter and let detection code directly set the NAND_BUSWIDTH_16 flag in
chip->options if needed.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Fix diacritics in some instances of my name and change my e-mail address
to kabel@kernel.org.
Add corresponding .mailmap entries.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
SPL on mvebu loads proper U-Boot from custom Marvell kwbimage format and
therefore support for other binary formats is not required to be present in
SPL. Boot source of proper U-Boot is defined by compile time options and
therefore it is not required to enable all possible and unused peripherals
in SPL by default.
This change decrease size of SPL binaries.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
A common external watchdog circuit is kept alive by triggering a short
pulse on the reset pin. This patch adds support for this use case, while
making the algorithm configurable in the devicetree.
The "linux,wdt-gpio" driver being modified is based off the equivalent
driver in the Linux kernel, which provides support for this algorithm.
This patch brings parity to this driver, and is kept aligned with
the functionality and devicetree configuration in the kernel.
It should be noted that this adds a required property named 'hw_algo'
to the devicetree binding, following suit with the kernel. I'm happy to
make this backward-compatible if preferred.
Signed-off-by: Paul Doelle <paaull.git@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Add support for hardware watchdog timer for Amlogic SoCs.
This driver has been heavily inspired by his Linux equivalent
(meson_gxbb_wdt.c).
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Philippe Boos <pboos@baylibre.com>
Reviewed-by: Stefan Roese <sr@denx.de>
This patch adds support for the Marvell Octeon watchdog driver, which
currently only support the ARM64 Octeon TX & TX2 platforms. Since the
IP is pretty similar, it makes sense to extend this driver to also
support the MIPS Octeon SoC.
A follow-up patch will enable this watchdog support on the EBB7304
eval board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
i2c changes for 2022.10
- new driver nuvoton, NPCM7xx from Jim Liu
Fixes:
- ast_i2c: Remove SCL direct drive mode
from Eddie James
- avoid dynamic stack use in dm_i2c_write
bloat-o-meter drivers/i2c/i2c-uclass.o.{0,1}
add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-144 (-144)
Function old new delta
dm_i2c_write 552 408 -144
Total: Before=3828, After=3684, chg -3.76%
patch from Rasmus Villemoes
To quote Andre:
One prominent feature is the restructering of the clock driver, which
allows to end up with one actual driver for all variants, although we
still only compile in support for one SoC.
Also contained are some initial SPI fixes, which should fix some
problems, and enable SPI flash support for the F1C100s SoC. Those
patches revealed more problems, I will queue fixes later on, but for
now it should at least still work.
Apart from some smaller fixes (for instance for NAND operation), there
is also preparation for the upcoming Allwinner D1 support, in form of
the USB PHY driver. There are more driver support patches to come.
The gitlab CI completed successfully, including the build test for all
160 sunxi boards. I also boot tested on a few boards, but didn't have
time for more elaborate tests this time.
The size of the dynamic stack allocation here is bounded by the if()
statement. However, just allocating the maximum size up-front and
doing malloc() if necessary avoids code duplication (the
i2c_setup_offset() until the invocation of ->xfer), and generates much
better (smaller) code:
bloat-o-meter drivers/i2c/i2c-uclass.o.{0,1}
add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-144 (-144)
Function old new delta
dm_i2c_write 552 408 -144
Total: Before=3828, After=3684, chg -3.76%
It also makes static analysis of maximum stack usage (using the .su
files that are automatically generated during build) easier if there
are no lines saying "dynamic".
[This is not entirely equivalent to the existing code; this now uses
the stack for len <= 64 rather than len <= 63, but that seems like a
more natural limit.]
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Heiko Schocher <hs@denx.de>
SCL direct drive mode prevents communication with devices that
do clock stretching, so disable. The Linux driver doesn't use
this mode, and the engine can handle clock stretching.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: ryan_chen <ryan_chen@aspeedtech.com>
