AT91sam9g10 is an ARM 926ej-s SOC. It is an evolution of the at91sam9261 with a
faster clock speed: 266/133MHz.
Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
AT91sam9g45 series is an ARM 926ej-s SOC family clocked at 400/133MHz.
It embeds USB high speed host and device, LCD, DDR2 RAM, and a full set of
peripherals.
The first board that embeds at91sam9g45 chip is the AT91SAM9G45-EKES.
On the board you can find 2 USART, USB high speed,
a 480*272 LG lcd, ethernet, gpio/joystick/buttons.
Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
ESPT-Giga is SH7763-based reference board.
Board support is relatively sparse, presently supporting serial,
gigabit ethernet, USB host, and MTD.
More information (in Japanese) available at:
http://www.cente.jp/product/cente_hard/ESPT-Giga.html
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add support for the Phytec phyCORE-MPC5200B-tiny.
Code originally from Pengutronix.de.
Created CONFIG_SYS_ATA_CS_ON_TIMER01 define for when IDE CS is on
Timer 0/1
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds support for esd gmbh MEESC board.
The MEESC is based on an Atmel AT91SAM9263 SoC.
Signed-off-by: Daniel Gorsulowski <Daniel.Gorsulowski@esd.eu>
Add support for Freescale's i.MX31 PDK board (a.k.a. 3 stack board).
This patch assumes that some other program performs the actual
NAND boot.
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Acked-by: Fabio Estevam <fabioestevam@yahoo.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Initial support for Extreme Engineering Solutions XPedite5170 -
a MPC8640-based 3U VPX single board computer with a PMC/XMC
site.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The PM9261 board is based on the AT91SAM9261-EK board.
Here is the page on Ronetix website:
http://www.ronetix.at/starter_kit_9261.html
Signed-off-by: Ilko Iliev <iliev@ronetix.at>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
The patch adds support for P2020DS reference platform.
DDR3 interface uses hard-coded initialization rather than SPD
for now and was tested at 667Mhz. Some PIXIS register
definitions and associated code sections need to be fixed.
TSEC1/2/3, NOR flash, MAC/SYS ID EEPROM, PCIE1/2/3 are all
tested under u-boot.
Signed-off-by: Srikanth Srinivasan <srikanth.srinivasan@freescale.com>
Signed-off-by: Travis Wheatley <Travis.Wheatley@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We rename the board so we use a consistent name in U-Boot and in
Linux. Also, we use this opportunity to move the board into the
Freecale vendor directory.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: John Rigby <jcrigby@gmail.com>
Initial U-Boot support for the DaVinci DM355 EVM. This is a board
from Spectrum Digital. Board docs include schematic and firmware
for its microcontroller:
http://c6000.spectrumdigital.com/evmdm355/revd/
Most of the DM355 chip is fully documented by TI, the most notable
exception being the MPEG/JPEG coprocessor (programmable using codecs
available at no cost from TI), which is omitted from its DM335 sibling:
http://focus.ti.com/docs/prod/folders/print/tms320dm355.html
This version can boot from the on-board DM9000 Ethernet chip, after
being loaded (from NAND, MMC/SD, or UART). In the near future, NAND
and USB support could be added ... NAND support is being held back
until the support for the 4-bit ECC hardware is ready.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The PM9263 board is based on the AT91SAM9263-EK board.
Here is the page on Ronetix website:
http://www.ronetix.at/starter_kit_9263.html
Signed-off-by: Ilko Iliev <iliev@ronetix.at>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
The AT91RM9200-EK Evaluation Board supports the AT91RM9200
ARM9-based 32-bit RISC microcontroller and enables real-time code development
and evaluation.
Here is the chip page on Atmel website:
http://www.atmel.com/dyn/products/tools_card.asp?tool_id=3507
with
- NOR (cfi driver)
- DataFlash
- USB OHCI
- Net
- I2C (hard)
Signed-off-by: Ulf Samuelsson <ulf@atmel.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
This patch adds MPC8569MDS board support. The UART, QE UEC1 and UEC2, BRD
EEPROM on I2C2 bus, PCI express and DDR3 SPD are supported in this patch.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Hillel Avni <Hillel.Avni@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
AT91sam9g20 is an evolution of the at91sam9260 with a faster clock speed.
The AT91SAM9G20-EK board is an updated revision of the AT91SAM9260-EK board.
It is essentially the same, with a few minor differences.
Here is the chip page on Atmel website:
http://www.atmel.com/dyn/products/product_card.asp?part_id=4337
Signed-off-by: Justin Waters <justin.waters@timesys.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
This patch adds support for the kmsupx4 board from Keymile,
based on a Freescale MPC852T CPU
- serial console on SMC1
- 32 MB SDRAM
- 32 MB NOR Flash
- Ethernet over SCC3
- I2C Bitbang
Signed-off-by: Heiko Schocher <hs@denx.de>
The TQM8548_AG is a variant of the TQM8548 module with 1 GiB memory,
CAN and without PCI/PCI-X and RTC. U-Boot can be built for this module
with "$ make TQM8548_AG_config".
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
The TQM8548_BE is a variant of the TQM8548 module with NAND and CAN
interface. With NAND support, the image is significantly larger and
TEXT_BASE is adjusted accordingly. U-Boot can be built for this
module with "$ make TQM8548_BE_config".
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Add BeagleBoard support, common power code and README.
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
Board support for the Guntermann & Drunck PowerPC 440 ETX module.
Based on the AMCC Yosemite board support by Stefan Roese.
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>
The NMDK8815 board is distributed by ST Microelectornics.
Other (proprietary) code must be run to unlock the CPU before
U-Boot runs. doc/README.nmdk8815 outlines the boot sequence.
This is the initial port, with basic infrastructure and
a working serial port.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stnwireless.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
This patch adds support for the kmeter1 board from Keymile,
based on a Freescale MPC8360 CPU.
- serial console on UART 1
- 256 MB DDR2 RAM
- 64 MB NOR Flash
- Ethernet RMII Mode over UCC4
- PHY SMSC LAN8700
Signed-off-by: Heiko Schocher <hs@denx.de>
We move all IO addressed (CCSR, localbus, PCI) above the 4G boundary
to allow for larger memory sizes.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch will create a new board, SIMPC8313, from Sheldon Instruments. This
board boots from NAND devices and is configureable for either large or small
page devices. The board supports non-soldered DDR2, one ethernet port, a
Marvell 88E1118 PHY, and PCI host support. The board also has a FPGA connected
to the eLBC providing glue logic to a TMS320C67xx DSP.
Signed-off-by: Ron Madrid <ron_madrid@sbcglobal.net>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Initial support for Extreme Engineering Solutions XPedite5200 -
a MPC8548-based PMC single board computer.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Initial support for Extreme Engineering Solutions XPedite5370 -
a MPC8572-based 3U VPX single board computer with a PMC/XMC
site.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
---
Microblaze platforms use generic settings and to have
many platforms is confusing that's why I decided to remove this
platform from U-BOOT. ml401 tree is sufficient for covering
all Microblaze platforms.
This change will go through microblaze custodian tree.
Add logic to the MAKEALL script to determine the number of CPU cores
on the system, and run a parallel build if there is more than one.
Usually this significantrly accelerates builds.
Allow to manually adjust the number of parallel make jobs by using
the "BUILD_NCPUS" environment variable.
Signed-off-by: Wolfgang Denk <wd@denx.de>
This patch adds support for the kmeter1 board from Keymile,
based on a Freescale MPC8360 CPU.
- serial console on UART 1
- 256 MB DDR2 RAM
- 64 MB NOR Flash
- Ethernet RMII Mode over UCC4
- PHY SMSC LAN8700
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch provides support for AFEB9260 board, a product of
OpenSource hardware and software. Some commertial projects
are made with this design. A board is basically AT91SAM9260-EK
with some modifications and different peripherals and different
parts used. Main purpose of this project is to gain experience in
hardware design.
More info: http://groups.google.com/group/arm9fpga-evolution-board
(In Russian only, sorry).
Subversion repository: svn://194.85.238.22/home/users/george/svn/arm9eb
Signed-off-by: Sergey Lapin <slapin@ossfans.org>
This patch adds support for the avnet fx12 minimodul.
It needs the "ppc4xx: Generic architecture for xilinx ppc405"
patch from Ricardo.
Signed-off-by: Georg Schardt <schardt@team-ctech.de>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@uam.es>
Signed-off-by: Stefan Roese <sr@denx.de>
The Arches Evaluation board is based on the AMCC 460GT SoC chip.
This board is a dual processor board with each processor providing
independent resources for Rapid IO, Gigabit Ethernet, and serial
communications. Each 460GT has it's own 512MB DDR2 memory, 32MB NOR
FLASH, UART, EEPROM and temperature sensor, along with a shared debug
port. The two 460GT's will communicate with each other via shared
memory, Gigabit Ethernet and x1 PCI-Express.
Signed-off-by: Adam Graham <agraham@amcc.com>
Signed-off-by: Victor Gallardo <vgallardo@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch provides an unificated way of handling xilinx v5 ppc440 boards.
It unificates 3 different things:
1) Source code
A new board called ppc440-generic has been created. This board includes
a generic tlb initialization (Maps the whole memory into virtual) and
defines board_pre_init, checkboard, initdram and get_sys_info weakly,
so, they can be replaced by specific functions.
If a new board needs to redefine any of the previous functions
(specific initialization) it can create a new directory with the
specific initializations needed. (see the example ml507 board).
2) Configuration file
Common configurations are located under configs/xilinx-ppc440.h, this
header file interpretes the xparameters file generated by EDK and
configurates u-boot in correspondence. Example: if there is a Temac,
allows CMD_CONFIG_NET
Specific configuration are located under specific configuration file.
(see the example ml507 board)
3) Makefile
Some work has been done in order to not duplicate work in the Main
Makefile. Please see the attached code.
In order to support new boards they can be implemented in the next way:
a) Simple Generic Board (90% of the time)
Using EDK generates a new xparameters.h file, replace
ppc440-generic/xparameters.h and run make xilinx-ppc440-generic_config
&& make
b) Simple Boards with special u-boot parameters (9 % of the time)
Create a new file under configs for it (use ml507.h as example) and
change your paramaters. Create a new Makefile paragraph and compile
c) Complex boards (1% of the time)
Create a new folder for the board, like the ml507
Finally, it adds support for the Avnet FX30T Evaluation board, following
the new generic structure:
Cheap board by Avnet for evaluating the Virtex5 FX technology.
This patch adds support for:
- UartLite
- 16MB Flash
- 64MB RAM
Prior using U-boot in this board, read carefully the ERRATA by Avnet
to solve some memory initialization issues.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@uam.es>
Signed-off-by: Stefan Roese <sr@denx.de>
AP325RXA is SH7723's reference board.
This has SCIF, NOR Flash, Ethernet, USB host, LCDC, SD Host, Camera and other.
In this patch, support SCIF, NOR Flash, and Ethernet.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This adds initial support for the RTE RSK+ SH7203 board.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This board has SH7785, 512MB DDR2-SDRAM, NOR Flash,
Graphic, Ethernet, USB, SD, RTC, and I2C controller.
This patch supports the following functions:
- 128MB DDR2-SDRAM (29-bit address mode only)
- NOR Flash
- USB host
- Ethernet
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
SMDK6400 can only boot U-Boot from NAND-flash. This patch adds a nand_spl
driver for it too. The board can also boot from the NOR flash, but due to
hardware limitations it can only address 64KiB on it, which is not enough
for U-Boot. Based on the original sources by Samsung for U-Boot 1.1.6.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Srikanth Srinivasan <srikanth.srinivasan@freescale.com>
Signed-off-by: Dejan Minic <minic@freescale.com>
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The MIMC200 board is based on Atmel's NGW100 dev kit, but with an extra
8MByte FLASH and 128KByte FRAM.
Signed-off-by: Mark Jackson <mpfj@mimc.co.uk>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This patch adds support for the Favr-32 board made by EarthLCD.
This kit, which is also called ezLCD-101 when running with EarthLCD firmware,
has a 10.4" touch screen LCD panel, 16 MB 32-bit SDRAM, 8 MB parallel flash,
Ethernet, audio out, USB device, SD-card slot, USART and various other
connectors for cennecting stuff to SPI, I2C, GPIO, etc.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This patch allows booting from FLASH the ML507 board by Xilinx.
Previously, U-Boot needed to be loaded from JTAG or a Sytem ACE CF
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@uam.es>
Signed-off-by: Stefan Roese <sr@denx.de>
The Hammerhead platform is built around a AVR32 32-bit microcontroller
from Atmel. It offers versatile peripherals, such as ethernet, usb
device, usb host etc.
The board also incooperates a power supply and is a Power over Ethernet
(PoE) Powered Device (PD).
Additonally, a Cyclone III FPGA from Altera is integrated on the board.
The FPGA is mapped into the 32-bit AVR memory bus. The FPGA offers two
DDR2 SDRAM interfaces, which will cover even the most exceptional need
of memory bandwidth. Together with the onboard video decoder the board
is ready for video processing.
For more information see: http:///www.miromico.com/hammerhead
Signed-off-by: Julien May <mailinglist@miromico.ch>
[haavard.skinnemoen@atmel.com: various small fixes and adaptions]
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Support for the adsvix was originally provided by Applied Data
Systems (ADS), inc., now EuroTech, Inc.
The board never shipped aside from some sample boards.
Signed-off-by: Adrian Filipi <adrian.filipi@eurotech.com>
The Xilinx ML507 Board is a Virtex 5 prototyping board that includes,
among others:
-Virtex 5 FX FPGA (With a ppc440x5 in it)
-256MB of SDRAM2
-32MB of Flash
-I2C Eeprom
-System ACE chip
-Serial ATA connectors
-RS232 Level Conversors
-Ethernet Transceiver
This patch gives support to a standard design produced by EDK for this
board: ppc440, uartlite, xilinx_int and flash
- Includes Changes propossed by Stefan Roese and Michal Simek
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@uam.es>
Acked-by: Stefan Roese <sr@denx.de>
The MVBC_P is a MPC5200B based camera system with Intel Gigabit ethernet
controller (using e1000) and custom Altera Cyclone-II FPGA on PCI.
Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add AMCC Redwood reference board that uses the latest
PPC 464 CPU processor combined with a rich mix of peripheral
controllers. The board will support PCIe, mutiple Gig ethernet
ports, advanced hardware RAID assistance and IEEE 1588.
Signed-off-by: Feng Kan <fkan@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
By Cleanup out-or-tree building for some boards (.depend)
(commit:c8a3b109f07f02342d097b30908965f7261d9f15)
because filse ware changed, some SH-boards have compile error.
I revised this problem.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This patch adds support for the Lyrtech SFF-SDR board,
based on the TI DaVinci architecture (ARM926EJS).
Signed-off-by: Hugo Villeneuve <hugo.villeneuve@lyrtech.com>
Signed-off-by: Philip Balister <philip@balister.org>
Signed-off-by: Wolfgang Denk <wd@denx.de>
This patch adds basic support for the TQM8548 module from TQ-Components
(http://www.tqc.de/) including DDR2 SDRAM initialisation and support for
eTSEC 3 and 4
Furthermore Flash buffer write has been enabled to speed up output to
the Flash by approx. a factor of 10.
Signed-off-by: Thomas Waehner <thomas.waehner@tqs.de>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Add MPC8343 based board mvBlueLYNX-M7.
It's a single board stereo camera system.
Please read doc/README.mvblm7 for details.
Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
SH7763RDP has SCIF, NOR Flash, Ethernet, USB host, LCDC and MMC.
In this patch, support SCIF, NOR Flash, and Ethernet.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This is a replacement for ATSTK1002 with 64MB SDRAM and NAND flash on
board. It's currently in production and will be available soon.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This patch adds support for the AT91SAM9RL chip and the AT91SAM9RLEK
board.
Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
This patch adds support for the AT91SAM9263 chip and the AT91SAM9263EK
board.
Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
This patch adds support for the AT91SAM9261 chip and the AT91SAM9261EK
board.
Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
This patch adds support for the MX31ADS evaluation board from Freescale,
initialization code is copied from RedBoot sources, also provided by
Freescale.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
This patch is based on the port by Mihai Georgian (see linkstation.c for
Copyright information) and implements support for LinkStation / KuroBox HD
and HG PPC models from Buffalo Technology, whereby HD is deactivated at
the moment, pending network driver fixing.
Notice to users: this is pretty much a barebone port. Support for network
on HG models is already in the U-Boot mainline, but you might also want
patches to switch fan / phy modes depending on the negotiated ethernet
parameters. This patch also doesn't support console switching, booting EM
mode, Buffalo specific ext2 magic number. So, if you want to use any of
those, you need additional patches. Otherwise this patche provides a fully
functional u-boot with a network console on your system.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
This patch adds support for the Phytec Phycore-i.MX31 board
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
This patch adds support for the mx31 litekit board
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
This board never went into production
Signed-off-by: Zachary P. Landau <zachary.landau@labxtechnologies.com>
Acked-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Acked-by: John Rigby <jrigby@freescale.com>
Add some missing ARM boards to MAKEALL. These build correctly,
unlike several of the boards already listed.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This patch adds support for the MX31ADS evaluation board from Freescale,
initialization code is copied from RedBoot sources, also provided by Freescale.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
This patch adds support for the Phytec Phycore-i.MX31 board
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
This patch adds support for the mx31 litekit board
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
R2D plus is SH reference board used with SH7751R.
This board has 266Mhz CPU, 64MB SDRAM, Cardbus, CF interface,
one PCI bus, VGA, and two Ethernet controller.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Renesas Solutions R7780MP is a reference board on SH7780.
This board has serial, 10/100 base Ethernet deivice, CF slot
and VGA devices. This board can set extension board.
Extension board has 10/100/1000 base Ethernet device, PCI slot,
S-ATA, iDVR slot.
Signed-off-by: Yusuke Goda <goda.yusuke@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Migo-R is a board based on SH7722 and has may devices.
In this patch, supported SCIF, NOR flash and Ethernet.
Signed-off-by: Yusuke Goda <goda.yusuke@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This patch adds support for the AMCC Glacier 460GT eval board.
The main difference to the Canyonlands board are listed here:
- 4 ethernet ports instead of 2
- no SATA port
- no USB port
Currently EMAC2+3 are not working. This will be fixed in a later
release.
Signed-off-by: Stefan Roese <sr@denx.de>
460EX doesn't support a fixed bootstrap option to boot from 512 byte page
NAND devices. The only bootstrap option for NAND booting is option F for
2k page devices. So to boot from a 512 bype page device, the I2C bootstrap
EEPROM needs to be programmed accordingly.
This patch adds basic NAND booting support for the AMCC Canyonlands aval
board and also adds support to the "bootstrap" command, to enable NAND
booting I2C setting.
Tested with 512 byte page NAND device (32MByte) on Canyonlands.
Signed-off-by: Stefan Roese <sr@denx.de>
Add support for the ATNGW100 Network Gateway reference design,
including flash, ethernet and MMC support.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Hi,
The patch adds 4 boards, called AcTux-1 .. AcTux-4. This patch contains the
files that
contain changes for multiple boards, the board-specific files follow as
separate patches.
Signed-off-by: Michael Schwingen <michael@schwingen.org>
With serial, NE2000, IDE support. Tested in big-endian mode.
Memory size hard-coded to 128M for now, so don't play with
the -m option.
Signed-off-by: Vlad Lungu <vlad@comsys.ro>
MPC837xERDB board support includes:
* DDR2 330MHz hardcoded (soldered on the board)
* Local Bus NOR Flash
* I2C, UART and RTC
* eTSEC RGMII (TSEC0 - RTL8211B with MII;
* TSEC1 - VSC7385 local bus, hardcoded, requires seperate firmware
* load)
Signed-off-by: Kevin Lam <kevin.lam@freescale.com>
Signed-off-by: Joe D'Abbraccio <joe.d'abbraccio@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The features list:
- Boot from NOR Flash
- DDR2 266MHz hardcoded configuration
- Local bus NOR Flash R/W operation
- I2C, UART, MII and RTC
- eTSEC0/1 support
- PCI host
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The TK885D board uses a TQM885D module from TQ, this port adds an
own configuration file and adds a last_stage_init() method to
configure the two PHYs, depending on the phy_auto_nego environment
variable.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
This is MPC8360E based board with:
- 256MB fixed SDRAM;
- 8MB Intel Strata NOR flash;
- StMICRO 64MiB NAND flash;
- two 10/100/1000 ethernet ports connected via Broadcom
BCM5481 PHYs;
- two 10/100 ethernet ports connected via National
DP83848 PHYs;
- one PCI and one miniPCI slots;
- four serial ports (two NS16550-compatible, two UCCs);
- four USB ports working through MPC8360E "FHCI" USB controller;
- Fujitsu MB86277 graphics controller;
- Analog to Digital Converter/Touchscreen controller, AD7843
connected to SPI.
Features not supported in this patch are:
- StMICRO 64MiB NAND flash (patch sent);
- MINT framebuffer initialization (patch is pending);
- Fetching production information from the EEPROM via I2C;
- FHCI USB;
- Two slow UCCs used as RS-485 UARTs.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Add support for Wind River's SBC8548 reference board.
Signed-off by: Joe Hamman <joe.hamman@embeddedspecialties.com>
Signed-off by: Andy Fleming <afleming@freescale.com>
This patch brings the PMC440 board configuration file.
Finally it enables the PMC440 board support.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
This board never left prototyping state and it
became a millstone round my neck. So remove it.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
These patches add support for the PPC440EPx-based "Korat" board to
U-Boot. They are based primarily on support for the Sequoia board.
Signed-off-by: Larry Johnson <lrj@acm.org>
ATSTK1004 is a daughterboard for ATSTK1000 with the AT32AP7002 CPU,
which is a derivative of AT32AP7000.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
ATSTK1003 is a daughterboard for ATSTK1000 with the AT32AP7001 CPU,
which is a derivative of AT32AP7000.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
This patch adds NAND booting support for the AMCC 405EX(r) eval boards.
Again, only one image supports both targets.
Signed-off-by: Stefan Roese <sr@denx.de>
The Haleakala is nearly identical with the Kilauea eval board. The only
difference is that the 405EXr only supports one EMAC and one PCIe
interface. This patch adds support for the Haleakala board by using
the identical image for Kilauea and Haleakala. The distinction is done
by comparing the PVR.
Signed-off-by: Stefan Roese <sr@denx.de>
Add MPC8360EMDS_ATM_config and MPC832XEMDS_ATM_config into
Makfile and MAKEALL
Signed-off-by: Tony Li <tony.li@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Mahesh Jade <mahesh.jade@freescale.com>
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Changes to the TSEC driver affect almost all 83xx, 85xx, and 86xx boards.
Now we can do a MAKEALL test on all of them!
Signed-off-by: Andy Fleming <afleming@freescale.com>
Add support for Wind River's SBC8641D reference board.
Signed-off by: Joe Hamman <joe.hamman@embeddedspecialties.com>
Acked-by: Wolfgang Denk <wd@denx.de>
Acked-by: Jon Loeliger <jdl@freescale.com>
Add support for the following DaVinci boards:
- DV_EVM
- SCHMOOGIE
- SONATA
Changes:
- Split into separate board directories
- Removed changes to MTD_DEBUG (or whatever it's called)
- New CONFIG_CMD party line followed
- Some cosmetic fixes, cleanup etc.
- Patches against the latest U-Boot tree as of now.
- Fixed CONFIG_CMD_NET in net files.
- Fixed CONFIG_CMD_EEPROM for schmoogie.
- Made sure it compiles and works (forceenv() link problem) on SCHMOOGIE and
DV_EVM. Can't check if it works on SONATA, don't have a board any more,
but it at least compiles.
Here is an excerpt from session log on SCHMOOGIE...
U-Boot 1.2.0-g6c33c785-dirty (Aug 7 2007 - 13:07:17)
DRAM: 128 MB
NAND: 128 MiB
In: serial
Out: serial
Err: serial
ARM Clock : 297MHz
DDR Clock : 162MHz
ETH PHY : DP83848 @ 0x01
U-Boot > iprobe
Valid chip addresses: 1B 38 3A 3D 3F 50 5D 6F
U-Boot > ping 192.168.253.10
host 192.168.253.10 is alive
U-Boot >
Signed-off-by: Sergey Kubushyn <ksi@koi8.net>
Acked-by: Dirk Behme <dirk.behme@gmail.com>
Acked-by: Zach Sadecki <Zach.Sadecki@ripcode.com>
Acked-by: Stefan Roese <sr@denx.de>
This series of patches adds support for 2 boards from Netstal Maschinen.
The HCU4 has a PPC405Gpr and
the HCU5 has a PPC440EPX.
The HCU4 has a somehow complicated flash setup, as the booteprom is
only 8 bits and the CFI 16 bits wide, which makes it impossible to use a more
elegant solution.
The HCU5 has only a booteprom as the whole code will be downloaded from a
different board which has HD, CD-ROM, etc and where all code is stored.
This is my third try. I incorporated all suggestions made by Wolfgang and Stefan.
Thanks them a lot.
Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
Add the ability for modules from the Schindler cm5200 family to use a
single U-Boot image:
- rename cm1_qp1 to cm5200
- add run-time module detection
- parametrize SDRAM configuration according to the module we are running on
Few minor, board-specific fixes included in this patch:
- better MAC address handling
- updated default environment ('update' command uses +{filesize} now)
- improved error messages in the auto-update code
- allow booting U-Boot from RAM (CFG_RAMBOOT)
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
Signed-off-by: Piotr Kruszynski <ppk@semihalf.com>
Signed-off-by: Bartlomiej Sieka <tur@semihalf.com>
