Commit graph

4496 commits

Author SHA1 Message Date
Peng Fan
1859b8b60d imx: move get_boot_device to common header
Most i.MX implements get_boot_device, move it to common header to
simplify code

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-07-26 11:29:00 +02:00
Peng Fan
793b760fb0 imx: simplify dependency with SPL_BOOTROM_SUPPORT
For SoCs support ROM API, CONFIG_SPL_BOOTROM_SUPPORT is needed,
so use this macro to guard the code to avoid extend the list.

And drop the guard with structure definition, there is no need.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-07-26 11:29:00 +02:00
Mamta Shukla
1c3a8e7753 configs: imx8mm: Define CONFIG_SYS_UBOOT_BASE for i.MX8m
The macro `CONFIG_SYS_UBOOT_BASE` is used by SPL loaders `"NOR"` and
`"XIP"` to determine the base address of u-boot.

For `"NOR"` on i.MX8MM it is the base address of QSPI0 plus the offset
of the flattened image tree blob.
Although `QSPI0_AMBA_BASE` is used to define CONFIG_SYS_UBOOT_BASE in
multiple board header files for i.MX8MM, it is not specified.

Specify offset of flattened image tree blob (needs to be set to same
value as specified in 'binman' node), base address of QSPI0 and size of
FlexSPI configuration block.

Signed-off-by: Mamta Shukla <mamta.shukla@leica-geosystems.com>
Signed-off-by: Thomas Haemmerle <thomas.haemmerle@leica-geosystems.com>
Tested-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Andrey Zhizhikin  <andrey.zhizhikin@leica-geosystems.com>
2022-07-25 15:35:35 +02:00
Rasmus Villemoes
748da8abb0 imx8: add rom api wrappers
The ROM API is thoroughly undocumented, but apparently passing the xor
of the real arguments as an extra argument is required [1]. Also, we
need to do the "save gd/restore gd" dance. These are both error-prone,
and lead to a lot of code duplication.

Since both imx8m[np] and imx8ulp SOCs have this, add a separate
translation unit which is included precisely when the new
CONFIG_IMX8_ROMAPI symbol is set, which provide convenience wrappers
that take care of computing the xor value as well as doing the gd
dance, and that thus have a more intuitive API. Subsequent patches
will make use of these to reduce boilerplate.

[1] One wonders, for example, if the check is only applied to the
lower 32 bits, or if we're implicitly relying on all 64-bit pointer
values we're passing effectively have 0 in the upper 32 bits.

Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
2022-07-25 15:35:34 +02:00
Rasmus Villemoes
de20c5d405 imx8: sys_proto.h: change guard logic around ROM API
This exposes the struct rom_api, the g_rom_api variable declaration
and the associated #defines to slightly fewer boards: namely, those
IMX8M which are not IMX8MN or IMX8MP. But the latter two are the only
IMX8M* ones where the g_rom_api variable is defined (in imx8m/soc.c),
so that should be fine.

Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
2022-07-25 15:35:34 +02:00
Tom Rini
36b661dc91 Merge branch 'next' 2022-07-11 14:58:57 -04:00
Tom Rini
95cc3efcc1 arm: Remove strongarm support
There are no platforms using this architecture anymore, remove it.

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-07-08 17:57:33 -04:00
Tom Rini
bb20a105e9 Convert CONFIG_SYS_BOOT_RAMDISK_HIGH to Kconfig
This converts the following to Kconfig:
   CONFIG_SYS_BOOT_RAMDISK_HIGH

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-07-07 14:01:09 -04:00
Tom Rini
a457ebd786 arm: Remove PXA architecture support
With the last platform for this architecture removed, remove the rest of
the architecture support as well.

Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2022-07-07 09:29:08 -04:00
Tom Rini
f1c6dfa426 layerscape: Remove some unused CONFIG symbols
All of these symbols are not referenced anywhere else in the code, so
remove them.

Cc: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2022-07-07 09:29:08 -04:00
Tom Rini
cd6a45a41f Convert CONFIG_USB_OHCI_NEW et al to Kconfig
This converts the following to Kconfig:
    CONFIG_SYS_OHCI_SWAP_REG_ACCESS
    CONFIG_SYS_USB_OHCI_CPU_INIT
    CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS
    CONFIG_SYS_USB_OHCI_SLOT_NAME
    CONFIG_USB_ATMEL
    CONFIG_USB_ATMEL_CLK_SEL_PLLB
    CONFIG_USB_ATMEL_CLK_SEL_UPLL
    CONFIG_USB_OHCI_LPC32XX
    CONFIG_USB_OHCI_NEW

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-07-07 09:29:08 -04:00
Tom Rini
52aaa1840d nxp: config_fsl_chain_trust.h: Clean up and remove unused portions
The way that secure boot is implemented today on NXP ARM platforms does
not reuse the elements found in include/config_fsl_chain_trust.h to
construct CONFIG_SECBOOT but instead board header files have their
environment setup as needed and then fsl_setenv_chain_of_trust() will
set secureboot in the environment.  Remove a large number of unused
defines here.

Cc: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2022-07-05 17:04:01 -04:00
Tom Rini
5aad0a14ba fsl_validate: Migrate SPL_UBOOT_KEY_HASH to Kconfig
Move setting of SPL_UBOOT_KEY_HASH to a non-NULL value to Kconfig.  As
part of this, change fsl_secboot_validate(...) to check that it is
passed a non-empty string, rather than non-NULL.

Cc: Peng Fan <peng.fan@nxp.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Kshitiz Varshney <kshitiz.varshney@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2022-07-05 17:04:01 -04:00
Tom Rini
601483ffd5 Convert CONFIG_SYS_FSL_SFP_BE et al to Kconfig
This converts the following to Kconfig:
   CONFIG_KEY_REVOCATION
   CONFIG_SYS_FSL_SFP_BE
   CONFIG_SYS_FSL_SFP_LE
   CONFIG_SYS_FSL_SFP_VER_3_0
   CONFIG_SYS_FSL_SFP_VER_3_2
   CONFIG_SYS_FSL_SFP_VER_3_4
   CONFIG_SYS_FSL_SRK_LE

This partly means making sure to enable SYS_FSL_ERRATUM_A007186 only for
when CHAIN_OF_TRUST is enabled.

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-07-05 17:04:00 -04:00
Tom Rini
c9f85187e2 Convert CONFIG_SYS_FSL_SEC_MON et al to Kconfig
This converts the following to Kconfig:
   CONFIG_SYS_FSL_SEC_MON
   CONFIG_SYS_FSL_SEC_MON_BE
   CONFIG_SYS_FSL_SEC_MON_LE

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-07-05 17:04:00 -04:00
Tom Rini
2b2817b5c8 Convert CONFIG_ESBC_HDR_LS et al to Kconfig
This converts the following to Kconfig:
   CONFIG_ESBC_HDR_LS
   CONFIG_ESBC_ADDR_64BIT

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-07-05 17:03:02 -04:00
Tom Rini
3371eddaa1 Convert CONFIG_USB_MAX_CONTROLLER_COUNT to Kconfig
This converts the following to Kconfig:
   CONFIG_USB_MAX_CONTROLLER_COUNT

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-06-28 17:11:48 -04:00
Tom Rini
24ec3dea4b arm: samsung: Migrate a number of symbols to Kconfig
- In a number of cases, use CONFIG_ARCH_EXYNOS[45] rather than
  CONFIG_EXYNOS[45]
- In other cases, test for CONFIG_ARCH_EXYNOS or CONFIG_ARCH_S5PC1XX
- Migrate specific SoC CONFIG values to Kconfig
- Use CONFIG_TARGET_x rather than CONFIG_x
- Migrate other CONFIG_EXYNOS_x symbols to Kconfig
- Reference CONFIG_EXYNOS_RELOCATE_CODE_BASE directly as EXYNOS_RELOCATE_CODE_BASE
- Rename CONFIG_S5P_PA_SYSRAM to CONFIG_SMP_PEN_ADDR to match the rest
  of U-Boot usage.

Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2022-06-28 17:04:37 -04:00
Tom Rini
093044735f usb: ehci-fsl: Remove non-DM code
The deadline for DM_USB migration has passed and all users have been
migrated.  Remove now unused code.

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-06-28 17:03:31 -04:00
Janne Grunau
e44d59c6ad arm: apple: nvme: Add SART support and RTKit buffer management
The NVMe firmware in the macOS 13 beta blocks or crashes with u-boot's
current minimal RTKit implementation. It does not provide buffers for
the firmware's buffer requests. The ANS2 firmware included in macOS 11
and 12 tolerates this. The firmware included in the first macOS 13 beta
requires buffers for the crashlog and ioreport endpoints to function.

In the case of the NVMe the buffers are physical memory. Access to
physical memory is guarded by what Apple calls SART.
Import m1n1's SART driver (exclusively used for the NVMe controller).
Implement buffer management helpers for RTKit. These are generic since
other devices (none in u-boot so far) require different handling.

Signed-off-by: Janne Grunau <j@jannau.net>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Tested-by: Mark Kettenis <kettenis@openbsd.org>
2022-06-23 08:24:49 -04:00
Jim Liu
0ae1c77199 misc: nuvoton: Add NPCM7xx otp controller driver
Add Nuvoton BMC npcm750 otp driver

Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
2022-06-22 21:30:05 -04:00
Jim Liu
9e03b48dfa crypto: nuvoton: Add NPCM7xx AES driver
add nuvoton BMC npcm750 AES driver

Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
2022-06-22 21:30:05 -04:00
Chia-Wei Wang
12770d0df0 ast2600: spl: Add boot mode detection
AST2600 supports boot from SPI(mmap), eMMC, and UART.
This patch adds the boot mode detection and return the
corresponding boot device type.

Signed-off-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
2022-06-22 21:30:05 -04:00
Tom Rini
52af0101be Merge branch 'master' into next
Merge in v2022.07-rc5.
2022-06-20 14:40:59 -04:00
Michael Walle
2a9cf320af armv8: layerscape: add missing RCW source defines
A board might need to get the source of the RCW word, which is also the
boot source in most cases.

These defines are taken from the LS1028A and I expect they are the same
across the SoCs with the same chassis, after all, there was already a
reset source for NOR flash.

Signed-off-by: Michael Walle <michael@walle.cc>
2022-06-20 15:52:45 +08:00
Andre Przywara
ce9c579e2b armv8: always use current exception level for TCR_ELx access
Currently get_tcr() takes an "el" parameter, to select the proper
version of the TCR_ELx system register.
This is problematic in case of the Apple M1, since it runs with
HCR_EL2.E2H fixed to 1, so TCR_EL2 is actually using the TCR_EL1 layout,
and we get the wrong version.

For U-Boot's purposes the only sensible choice here is the current
exception level, and indeed most callers treat it like that, so let's
remove that parameter and read the current EL inside the function.
This allows us to check for the E2H bit, and pretend it's EL1 in this
case.

There are two callers which don't care about the EL, and they pass 0,
which looks wrong, but is irrelevant in these two cases, since we don't
use the return value there. So the change cannot affect those two.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Tested-by: Mark Kettenis <kettenis@openbsd.org>
2022-06-16 15:22:55 -04:00
Tom Rini
3135ba642f arm: pxa: Remove CONFIG_CPU_PXA25X
There are no platforms that set this, remove the code.

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-06-06 12:09:12 -04:00
Tom Rini
6074a536d5 ppc / layerscape: Clean up CONFIG_SYS_CCSR_DO_NOT_RELOCATE usage
A number of PowerPC platforms define this, for SPL.  To move this to
Kconfig, it needs to be CONFIG_SPL_SYS_CCSR_DO_NOT_RELOCATE, so use
CONFIG_IS_ENABLED() to check for usage.  A number of layerscape
platforms bring this logic from PowerPC, but only need a small part of
it, for the fman driver.  Remove their unused portion at least.

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-06-06 12:09:12 -04:00
Tom Rini
12f613cf0e arm: omap2plus: Move CONFIG_SYS_PTV out of CONFIG namespace
This is always defined to 2, and referenced in two places.  Move the
define to <asm/omap_common.h> and make sure the code that uses this
includes that file.  Make <asm/arch-omap*/clock.h> not include that
file, as we don't need to be doing so.

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-06-06 12:09:00 -04:00
Andre Przywara
2b641211c5 armv8: Fix TCR 64-bit writes
The AArch64 TCR_ELx register is a 64-bit register, and many newer
architecture features use bits in the upper half. So far U-Boot was
igorant of those bits, trying to leave them alone.
However, in an effort to set bit 31 to 1, it failed doing so, because
the compiler sign-extended "1 << 31", so that all bits[63:31] got set.

Older ARMv8.0 cores don't define anything dangerous up there, but newer
architecture revisions do, and setting all those bits will end badly:
=================
$ qemu-system-aarch64 -cpu max ....
U-Boot 2022.07-rc1 (May 09 2022 - 15:21:00 +0100)

DRAM:  1.5 GiB
=================  (hangs here)

Defining TCR_ELx_RSVD to "1U << 31" avoids the sign-extension, so all
upper bits stay at a safe 0 value. This means no more surprises when
U-Boot runs on a more capable CPU core.

Reported-by: Balaji Anandapadmanaban <Balaji.Anandapadmanaban@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Peter Collingbourne <pcc@google.com>
Reviewed-by: Peter Collingbourne <pcc@google.com>
2022-06-03 11:15:24 -04:00
Gaurav Jain
cad77280c3 i.MX8ULP: add display_ele_fw_version api
implement get f/w version api.
print ele f/w version in spl.

Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Pankaj Gupta <pankaj.gupta@nxp.com>
2022-05-20 12:36:47 +02:00
Rasmus Villemoes
290ffe5788 imx8m: fix reading of DDR4 MR registers
I was trying to employ lpddr4_mr_read() to something similar to what
the imx8mm-cl-iot-gate board is doing for auto-detecting the RAM
type. However, the version in drivers/ddr/imx/imx8m/ddrphy_utils.c
differs from the private one used by that board in how it extracts the
byte value, and I was only getting zeroes. Adding a bit of debug
printf'ing gives me

 tmp = 0x00ffff00
 tmp = 0x00070700
 tmp = 0x00000000
 tmp = 0x00101000

and indeed I was expecting a (combined) value of 0xff070010 (0xff
being Manufacturer ID for Micron). I can't find any documentation that
says how the values are supposed to be read, but clearly the iot-gate
definition is the right one, both for its use case as well as my
imx8mp-based board.

So lift the private definition of lpddr4_mr_read() from the
imx8mm-cl-iot-gate board code to ddrphy_utils.c, and add a declaration
in the ddr.h header where e.g. get_trained_CDD() is already declared.

This has only been compile-tested for the imx8mm-cl-iot-gate
board (since I don't have the hardware), but since I've merely moved
its definition of lpddr4_mr_read(), I'd be surprised if it changed
anything for that board.

Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Tested-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Reviewed-by: Fabio Estevam <festevam@denx.de>
2022-05-20 09:30:28 +02:00
Marek Vasut
c329f9349b ARM: imx: imx31: Introduce and use UART_BASE_ADDR(n)
Introduce helper macro UART_BASE_ADDR(n), which returns Nth UART base
address. Convert all board configurations to this new macro. This is the
first step toward switching CONFIG_MXC_UART_BASE to Kconfig. This is a
clean up, no functional change.

The new macro contains compile-time test to verify N is in suitable
range. The test works such that it multiplies constant N by constant
double-negation of size of a non-empty structure, i.e. it multiplies
constant N by constant 1 in each successful compilation case.

The non-empty structure may contain C11 _Static_assert(), make use of
this and place the kernel variant of static assert in there, so that
it performs the compile-time check for N in the correct range. Note
that it is not possible to directly use static_assert in compound
statements, hence this convoluted construct.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2022-05-20 09:03:01 +02:00
Marek Vasut
be23774ed1 ARM: imx: imx27: Introduce and use UART_BASE_ADDR(n)
Introduce helper macro UART_BASE_ADDR(n), which returns Nth UART base
address. Convert all board configurations to this new macro. This is the
first step toward switching CONFIG_MXC_UART_BASE to Kconfig. This is a
clean up, no functional change.

The new macro contains compile-time test to verify N is in suitable
range. The test works such that it multiplies constant N by constant
double-negation of size of a non-empty structure, i.e. it multiplies
constant N by constant 1 in each successful compilation case.

The non-empty structure may contain C11 _Static_assert(), make use of
this and place the kernel variant of static assert in there, so that
it performs the compile-time check for N in the correct range. Note
that it is not possible to directly use static_assert in compound
statements, hence this convoluted construct.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2022-05-20 09:03:01 +02:00
Marek Vasut
52b6b480db ARM: imx: imx8m: Introduce and use UART_BASE_ADDR(n)
Introduce helper macro UART_BASE_ADDR(n), which returns Nth UART base
address. Convert all board configurations to this new macro. This is the
first step toward switching CONFIG_MXC_UART_BASE to Kconfig. This is a
clean up, no functional change.

The new macro contains compile-time test to verify N is in suitable
range. The test works such that it multiplies constant N by constant
double-negation of size of a non-empty structure, i.e. it multiplies
constant N by constant 1 in each successful compilation case.

The non-empty structure may contain C11 _Static_assert(), make use of
this and place the kernel variant of static assert in there, so that
it performs the compile-time check for N in the correct range. Note
that it is not possible to directly use static_assert in compound
statements, hence this convoluted construct.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2022-05-20 09:03:01 +02:00
Jim Liu
84335544ea arm: nuvoton: Add support for Nuvoton NPCM750 BMC
Add basic support for the Nuvoton NPCM750 EVB (Poleg).

Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
2022-05-05 09:28:47 -04:00
Tim Harvey
e3bdc97148 pci: imx: remove weak overrides no longer used
There are no users of the imx6_pcie_toggle_power and imx6_pcie_toggle_reset
weak overrides and as these functions are able to be handled now via dt
properties lets remove these.

Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2022-04-21 14:38:03 +02:00
Tim Harvey
6f6e069ca3 pci: imx: use vpcie-supply if defined by device-tree
If vpcie-supply is defined by device-tree use that if
CONFIG_PCIE_IMX_POWER_GPIO is not defined.

Note that after this the following boards which define
CONFIG_PCIE_IMX_POWER_GPIO in their board header file as well as their
device-tree should be able to remove CONFIG_PCIE_IMX_PERST_GPIO without
consequence:
 - mx6sabresd
 - mx6sxsabresd
 - novena

Note that the ge_bx50v3 board uses CONFIG_PCIE_IMX_POWER_GPIO and does
not have vpcie-supply defined in it's pcie node in the dt thus removing
CONFIG_PCIE_IMX_POWER_GPIO globally can't be done until that board adds
vpcie-supply.

Cc: Ian Ray <ian.ray@ge.com> (maintainer:GE BX50V3 BOARD)
Cc: Sebastian Reichel <sebastian.reichel@collabora.com> (maintainer:GE BX50V3 BOARD)
Cc: Fabio Estevam <festevam@gmail.com> (maintainer:MX6SABRESD BOARD)
Cc: Marek Vasut <marex@denx.de> (maintainer:NOVENA BOARD)
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2022-04-21 14:38:03 +02:00
Marek Vasut
19842b6a20 imx: power-domain: Inline arch-imx8m/power-domain.h
The arch/arm/include/asm/arch-imx8m/power-domain.h is not included
anywhere except in drivers/power/domain/imx8m-power-domain.c, just
inline the content and drop the header. No functional change.

Tested-By: Tim Harvey <tharvey@gateworks.com> #imx8mp-venice-defconfig
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2022-04-21 12:44:23 +02:00
Johan Jonker
33f4750783 rockchip: rk3066: add core support
Add the core architecture code for the rk3066.

Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2022-04-18 11:25:13 +08:00
Paweł Jarosz
730a402450 rockchip: rk3066: add clock driver for rk3066 soc
Add the clock driver for the rk3066 platform.

Derived from the rk3288 and rk3188 driver it
supports only a bare minimum to bring up the system
to reduce the TPL size for:
  SDRAM clock configuration.
  The boot devices NAND, EMMC, SDMMC, SPI.
  A UART for the debug messages (fixed) at 115200n8.
  A SARADC for the recovery button.
  A TIMER for the delays (fixed).

There's support for two possible frequencies,
the safe 600MHz which will work with default pmic settings and
will be set to get away from the 24MHz default and
the maximum of 1.416Ghz, which boards can set if they
were able to get pmic support for it.

After the clock tree is set during the TPL probe
there's no parent update support.

In OF_REAL mode the drivers ns16550.c and dw-apb-timer.c
obtain the (fixed) clk_get_rate from the clock driver
instead of platdata.

The rk3066 cru node has a number of assigned-clocks properties
that call the .set_rate() function. Add them to the list so that
they return a 0 instead of -ENOENT.

Signed-off-by: Paweł Jarosz <paweljarosz3691@gmail.com>
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2022-04-18 11:25:13 +08:00
Paweł Jarosz
e6b0ed0e74 rockchip: rk3066: add grf header file
grf is needed by various drivers for rk3066 soc.

Signed-off-by: Paweł Jarosz <paweljarosz3691@gmail.com>
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2022-04-18 11:25:13 +08:00
Jesse Taube
a2d6fbf5ff clk: imxrt: Use dts for anatop base address
In Linux IMX and IMXRT use the device tree to hold the anatop address.
The anatop is used in clock drivers as it controls the internal PLLs
This will move the macro from asm/arch-imxrt to the device tree.
This presumably should also be done with the other IMX boards as well.

Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
2022-04-12 21:08:23 +02:00
Michael Trimarchi
1dd4985ed4 imx8m: add init_nand_clk
Add init_nand_clk to enable gpmi nand clock. Since i.MX8M not use CCF,
so we still use legacy mode to configure the clock.

Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
2022-04-12 19:10:44 +02:00
Michael Trimarchi
1247c444d6 imx8m: add regs used by GPMI
Add regs used by GPMI

Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
2022-04-12 19:10:44 +02:00
Peng Fan
fd437083b8 imx: imx8mp: Add iMX8MP UltraLite Part cpu type
Add i.MX8MP UltraLite Part CPU type

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-04-12 19:10:43 +02:00
Peng Fan
f342c9e381 imx: dynamic setting mmcdev and mmcroot
Dynamic setting mmcdev and mmcroot.
Then when boot linux, we can have correct "root=/dev/mmcblk[x]p2"

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-04-12 19:10:43 +02:00
Ye Li
203412f66d misc: S400_API: Update S400 API for buffer dump
Add ahab_dump_buffer API to dump AHAB buffer for debug purpose

Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-04-12 17:33:57 +02:00
Clement Faure
a55ca506c9 misc: S400_API: add ahab_release_caam
Add ahab_release_caam() function to the S400 API.

Signed-off-by: Clement Faure <clement.faure@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-04-12 17:33:56 +02:00
Ye Li
4ab38f6822 imx: imx8ulp_evk: Skip init DDR for reboot in dual boot mode
When M33 is LPAV owner in dual boot, DDR, PCC5, CGC2 won't be reset
during APD reset. So no need to init DDR again after reboot, but need to
reconfigure the PLL4 PFD/PFDDIV/LPAV NIC etc, because kernel may
change or disable some of them.

Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-04-12 17:33:56 +02:00
Peng Fan
a092f33305 imx: imx8ulp: add ND/LD clock
Add a new ddr script, defconfig for ND
Configure the clock for ND mode
changing A35 to 960MHz for OD mode
Update NIC CLK for the various modes
Introduce clock_init_early/late, late is used after pmic voltage
setting, early is used in the very early stage for upower mu, lpuart and
etc.

Note: NIC runs at 324MHz, 442MHz has some random kernel hang issue with
cpuidle enabled now.

Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-04-12 17:33:56 +02:00
Peng Fan
40d60ec780 imx: imx8ulp: add CAAM clock entry
Add CAAM clock entry in PCC3

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-04-12 17:33:56 +02:00
Ye Li
5579d66e37 imx: imx8ulp: Add M33 handshake functions
Add functions to check if M33 image is booted and handshake with M33
image via MU. A core notifies M33 to start init by FCR F0, then wait
M33 init done signal by checking FSR F0.

Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-04-12 17:33:56 +02:00
Peng Fan
8576f1a67a imx: imx8ulp: include pcc/cgc header in clock header
With this change, we no need to include pcc/cgc header files both.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-04-12 17:33:56 +02:00
Tommaso Merciai
625a3fe90c arch: mach-imx: imx8m: add pwm_regs struct in imx-regs
Add pwm_regs struct for i.MX8MM SOC

Signed-off-by: Tommaso Merciai <tommaso.merciai@amarulasolutions.com>
2022-04-12 17:33:55 +02:00
Tommaso Merciai
4aee7d0b84 arch: mach-imx: imx8m: add pwm ctrl registers fields defines
Add pwm control registers fields defines into imx-regs.h:

 - prescaler
 - dozeen
 - waiten
 - dbgen
 - clksrc_ipg_high
 - clksrc_ipg, en field

References:
 - iMX8MMRM.pdf p 3884

Signed-off-by: Tommaso Merciai <tommaso.merciai@amarulasolutions.com>
2022-04-12 17:33:55 +02:00
Marek Vasut
e26d0152d6 ARM: imx: Decode ECSPI env location from i.MX8M ROMAPI tables
Decode ECSPI boot device in env_get_location() from i.MX8M ROMAPI tables.
This is necessary to correctly identify env is in SPI NOR when the system
boots from SPI NOR attached to ECSPI.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
2022-04-12 17:33:55 +02:00
Gaurav Jain
cb5d0419f5 crypto/fsl: i.MX8: Enable Job ring driver model.
i.MX8(QM/QXP) - added support for JR driver model.
sec is initialized based on job ring information processed
from device tree.

Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
2022-04-12 11:19:21 +02:00
Tom Rini
2fc0995cc0 arm: Remove unused ep93xx code
There are no platforms for this architecture anymore, remove unused
code.

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-04-08 10:46:22 -04:00
Tom Rini
4de720e98d Merge branch 'master' of https://source.denx.de/u-boot/custodians/u-boot-sunxi
A big part is the DM pinctrl driver, which allows us to get rid of quite
some custom pinmux code and make the whole port much more robust. Many
thanks to Samuel for that nice contribution! There are some more or less
cosmetic warnings about missing clocks right now, I will send the trivial
fixes for that later.
Another big chunk is the mkimage upgrade, which adds RISC-V and TOC0
(secure images) support. Both features are unused at the moment, but I
have an always-secure board that will use that once the DT lands in the
kernel.
On top of those big things we have some smaller fixes, improving the
I2C DM support, fixing some H6/H616 early clock setup and improving the
eMMC boot partition support.

The gitlab CI completed successfully, including the build test for all
161 sunxi boards. I also boot tested on a A64, A20, H3, H6, and F1C100
board. USB, SD card, eMMC, and Ethernet all work there (where applicable).
2022-04-05 08:33:32 -04:00
Jernej Skrabec
1772771ac0 sunxi: prcm: Add a few registers
H6 and H616 SPL code has a few writes to unknown PRCM registers. Now
that we know what they are, let's replace magic offsets with proper
register names.

Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2022-04-04 23:24:17 +01:00
Angelo Dureghello
482c1ccd1c sunxi: H3: fix non working console on uart2
Fix non working console on uart2, that seems releated to both
Allwinner H2+ and H3.

Signed-off-by: Angelo Dureghello <angelo.dureghello@timesys.com>
[Andre: remove H2+, rearrange pin setup order]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2022-04-04 23:24:17 +01:00
Samuel Holland
44de13d945 sunxi: Support SPL in both eGON and TOC0 images
SPL uses the image header to detect the boot device and to find the
offset of the next U-Boot stage. Since this information is stored
differently in the eGON and TOC0 image headers, add code to find the
correct value based on the image type currently in use.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2022-04-04 23:24:17 +01:00
Samuel Holland
458e59da5d pwm: sunxi: Remove non-DM pin setup
This is now handled automatically by the pinctrl driver.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2022-04-04 23:24:17 +01:00
Samuel Holland
aadf3d5383 sunxi: Remove options and setup code for I2C2-I2C4
These options are not currently enabled anywhere. Any new users should
use DM clocks and pinctrl.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2022-04-04 23:24:16 +01:00
Samuel Holland
3e42d919af sunxi: Remove non-DM GMAC pin setup
This is now handled automatically by the pinctrl driver.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2022-04-04 23:24:16 +01:00
Samuel Holland
12bd00aafc net: sunxi_emac: Remove non-DM pin setup
This is now handled automatically by the pinctrl driver.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2022-04-04 23:24:16 +01:00
Samuel Holland
b799eabc7e sunxi: pinctrl: Create the driver skeleton
Create a do-nothing driver for each sunxi pin controller variant.

Since only one driver can automatically bind to a DT node, since the
GPIO driver already requires a manual binding process, and since the
pinctrl driver needs access to some of the same information, refactor
the GPIO driver to be bound by the pinctrl driver. This commit should
cause no functional change.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2022-04-04 23:23:50 +01:00
Sean Anderson
6d16157426 arm64: Import some ESR and SPSR defines from Linux
This imports some defines for esr and spsr from Linux v5.16. I have
modified the includes and fixed some indentation nits but otherwise it
is the same. There are a lot more defines than we need, but it doesn't
hurt.

Signed-off-by: Sean Anderson <sean.anderson@seco.com>
2022-04-01 16:56:53 -04:00
Sean Anderson
e75d791c50 arm64: Save spsr in pt_regs
This register holds "pstate" which includes (among other things) the
instruction mode the CPU was in when the exception was taken. This is
necessary to correctly interpret instructions at elr.

Signed-off-by: Sean Anderson <sean.anderson@seco.com>
2022-04-01 16:56:53 -04:00
Sean Anderson
e97ac4780d arm64: Save esr in pt_regs
To avoid passing around an extra register everywhere, save esr in
pt_regs like the rest. For proper alignment we need to have a second
(unused) register. All the printfs have to be adjusted, since
it's now an unsigned long and not an int.

Signed-off-by: Sean Anderson <sean.anderson@seco.com>
2022-04-01 16:56:53 -04:00
Sean Anderson
8e1c9fe243 spl: Add semihosting boot method
This adds a boot method for loading the next stage from the host. It is
mostly modeled off of spl_load_image_ext. I am not really sure why/how
spl_load_image_fat uses three different methods to load the image, but
the simple case seems to work OK for now.

To control the presence of this boot method, we add a config symbol.
While we're at it, we update the original semihosting config symbol.

I think semihosting has some advantages of other forms of JTAG boot.
Common other ways to boot from JTAG include:

- Implementing DDR initialization through JTAG (typically with dozens of
  lines of TCL) and then loading U-Boot. The DDR initialization
  typically uses hard-coded register writes, and is not easily adapted
  to different boards. BOOT_DEVICE_SMH allows booting with SPL,
  leveraging U-Boot's existing DDR initialization code. This is the
  method used by NXP's CodeWarrior IDE on Layerscape processors (see
  AN12270).
- Loading a bootloader into SDRAM, waiting for it to initialize DDR, and
  then loading U-Boot. This is tricky, because the debugger must stop the
  boot after the bootloader has completed its work. Trying to load
  U-Boot too early can cause failure to boot. This is the method used by
  Xilinx with its Zynq(MP) processors.
- Loading SPL with BOOT_DEVICE_RAM and breaking before SPL loads the
  image to load U-Boot at the appropriate place. This can be a bit
  tricky, because the load address is dependent on the header size. An
  elf with symbols must also be used in order to stop at the appropriate
  point. BOOT_DEVICE_SMH can be viewed as an extension of this process,
  where SPL automatically stops and tells the host where to place the
  image.

Signed-off-by: Sean Anderson <sean.anderson@seco.com>
2022-04-01 15:03:13 -04:00
Simon Glass
77f46f0607 video: fsl: colibri_vf: Drop FSL DCU driver
This does not use driver model and is more than two years past the
migration date. Drop it.

It can be added back later if needed.

Signed-off-by: Simon Glass <sjg@chromium.org>
2022-03-28 20:18:07 +02:00
Simon Glass
1fa43cad86 video: Drop references to CONFIG_VIDEO et al
Drop the Kconfigs which are not used and all references to them. In
particular, this drops CONFIG_VIDEO to avoid confusion and allow us to
eventually rename CONFIG_DM_VIDEO to CONFIG_VIDEO.

Also drop the prototype for video_get_info_str() which is no-longer used.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Jason Liu <jason.hui.liu@nxp.com>
2022-03-28 20:17:07 +02:00
Tom Rini
16199a8b96 Convert CONFIG_PHY_RESET_DELAY to Kconfig
This converts the following to Kconfig:
   CONFIG_PHY_RESET_DELAY

Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2022-03-25 12:01:15 +00:00
Tom Rini
2abf048ab7 Prepare v2022.04-rc4
-----BEGIN PGP SIGNATURE-----
 
 iQGzBAABCgAdFiEEGjx/cOCPqxcHgJu/FHw5/5Y0tywFAmIvp/8ACgkQFHw5/5Y0
 tyyI6wwApR++p9BBlWEZn1B5sivCXcs9oCX3Vs8vegpiiRbs/pGsyKV6pfEHHYV5
 lhw1YNZ0accKmqBmX19tdpQ2ZzHq3+g0eGJL8xioXU3hRoZZNsDewAF8KS+aHPpk
 qMuA+xbDi08I6z2qtrIpaDd//DO2jAkFF+/TKOzSgUSxBaomQiziZaB2x28bIBH2
 zsLMP4vzZ03uCSZVSd7HMBz0qiGhioJo5Ch2eU4TTJW19CXeMTAuav6SDq+6vJGi
 cIUe31YEe742jOVmtf2RuJQ+mDjsEfT11wvRajcbOlH/Ho7E5iFxQkmOEThpvybE
 YD5d5uLLpQj42PfBpSvx4nMJcvyOmqxdizUJxCgi/q5HrhdzcO6LwLLON0T4W4zG
 Vsue+iTjOKXgLdD8g/VogL38iHxhpfY7zsFB98vvHcoLwhEXvfvhO8Dj/lwLw4Ic
 88B6uz3TqAPNqSnTWphJPCwG8STwyqlvLXwTF+eICbtQW3uuHEtnmlsXQJeFmdUa
 fGK8dUfr
 =wyE5
 -----END PGP SIGNATURE-----

Merge tag 'v2022.04-rc4' into next

Prepare v2022.04-rc4
2022-03-14 17:40:36 -04:00
Jesse Taube
0dcdaff8b8 mach-sunxi: Add SPL SPI boot for SUNIV
The SUNIV SoCs come with a sun6i-style SPI controller at the base address
of sun4i SPI controller. The module clock of the SPI controller is
missing which leaves us running directly from the AHB clock, which is
set to 200MHz.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
[Icenowy: Original implementation]
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
[Jesse: adaptation to Upstream U-Boot]
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2022-03-03 01:24:06 +00:00
Jesse Taube
a08b04b5c7 mach-sunxi: Add boot device detection for SUNIV/F1C100s
In contrast to other Allwinner SoCs the F1C100s BROM does not store a
boot source indicator in the eGON header in SRAM. This leaves the SPL
guessing where we were exactly booted from, and for instance trying
the SD card first, even though we booted from SPI flash.

By inspecting the BROM code and by experimentation, Samuel found that the
top of the BROM stack contains unique pointers for each of the boot
sources, which we can use as a boot source indicator.

This patch removes the existing board_boot_order bodge and replace it
with a proper boot source indication function.

The only caveat is that this only works in the SPL, as the SPL header
gets overwritten with the exception vectors, once U-Boot proper takes
over. Always return MMC0 as the boot source, when called from U-Boot
proper, as a placeholder for now, until we find another way.

Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Suggested-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2022-03-03 01:23:58 +00:00
Andre Przywara
5ff4857d35 armv8: Fix and simplify branch_if_master/branch_if_slave
The branch_if_master macro jumps to a label if the CPU is the "master"
core, which we define as having all affinity levels set to 0. To check
for this condition, we need to mask off some bits from the MPIDR
register, then compare the remaining register value against zero.

The implementation of this was slighly broken (it preserved the upper
RES0 bits), overly complicated and hard to understand, especially since
it lacked comments. The same was true for the very similar
branch_if_slave macro.

Use a much shorter assembly sequence for those checks, use the same
masking for both macros (just negate the final branch), and put some
comments on them, to make it clear what the code does.
This allows to drop the second temporary register for branch_if_master,
so we adjust all call sites as well.

Also use the opportunity to remove a misleading comment: the macro
works fine on SoCs with multiple clusters. Judging by the commit
message, the original problem with the Juno SoC stems from the fact that
the master CPU *can* be configured to be from cluster 1, so the
assumption that the master CPU has all affinity values set to 0 does not
hold there. But this is already mentioned above in a comment, so remove
the extra comment.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2022-03-02 13:59:29 -05:00
Andre Przywara
f660fe0bd3 armv8: Simplify switch_el macro
The switch_el macro is a neat contraption to handle cases where we need
different code depending on the current exception level, but its
implementation was longer than needed.

Simplify it by doing just one comparison, then using the different
condition codes to branch to the desired target. PState.CurrentEL just
holds two bits, and since we don't care about EL0, we can use >, =, < to
select EL3, EL2 and EL1, respectively.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2022-03-02 13:59:29 -05:00
Andre Przywara
7ab2e47d27 arm: Clean up asm/io.h
asm/io.h is the header file containing the central MMIO accessor macros.
Judging by the header and the comments, it was apparently once copied
from the Linux kernel, but has deviated since then *heavily*. There is
absolutely no point in staying close to the original Linux code anymore,
so just remove the old cruft, by:
- removing pointless Linux history
- removing commented code
- removing outdated comments
- removing unused definitions (for mem_isa)

This massively improves the readability of the file.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2022-03-02 13:59:29 -05:00
Andre Przywara
6c7691edd5 armv8: Always unmask SErrors
The ARMv8 architecture describes the "SError interrupt" as the fourth
kind of exception, next to synchronous exceptions, IRQs, and FIQs.
Those SErrors signal exceptional conditions from which the system might
not easily recover, and are normally generated by the interconnect as a
response to some bus error. A typical situation is access to a
non-existing memory address or device, but it might be deliberately
triggered by a device as well.
The SError interrupt replaces the Armv7 asynchronous abort.

Trusted Firmware enters U-Boot (BL33) typically with SErrors masked,
and we never enable them. However any SError condition still triggers
the SError interrupt, and this condition stays pending, it just won't be
handled. If now later on the Linux kernel unmasks the "A" bit in PState,
it will immediately take the exception, leading to a kernel crash.
This leaves many people scratching their head about the reason for
this, and leads to long debug sessions, possibly looking at the wrong
places (the kernel, but not U-Boot).

To avoid the situation, just unmask SErrors early in the ARMv8 boot
process, so that the U-Boot exception handlers reports them in a timely
manner. As SErrors are typically asynchronous, the register dump does
not need to point at the actual culprit, but it should happen very
shortly after the condition.

For those exceptions to be taken, we also need to route them to EL2,
if U-Boot is running in this exception level.

This removes the respective code snippet from the Freescale lowlevel
routine, as this is now handled in generic ARMv8 code.

Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2022-03-02 13:59:29 -05:00
Adam Ford
0935dbf4c9 usb: ehci-omap: Drop dead code
omap_ehci_hcd_stop appears to be dead code, and omap_ehci_hcd_init
is only called by the probe function, so it can be static to that
function.  Remove both from the header along with some additional
checking for DM_USB.

Signed-off-by: Adam Ford <aford173@gmail.com>
2022-02-23 05:25:17 +01:00
Adam Ford
68a51cc8ec arm: omap3: Make some memory functions static and clean headers
There are a few memory functions for both the emif4 (AM3517)
and sdrc (OMAP35/DM37) code that can be defined as static,
because those functions are not used externally. Make them
static and clean up some of the corresponding headers.

Signed-off-by: Adam Ford <aford173@gmail.com>
2022-02-21 08:35:40 -05:00
Adam Ford
1c6ea4da24 arm: omap3: Cleanup sys_info to fit OMAP3 booting with LTO
With LTO enabled, some functions appear to be optimized in a
way that causes hanging on some OMAP3 boards after some
unrelated patches were applied.  The solution appears to make
several functions __used.  There also appears be to be some
dead code, so remove it while cleaning this up.

This has been tested on a general purpose OMAP3530, DM3730,
and AM3517.

Signed-off-by: Adam Ford <aford173@gmail.com>
2022-02-21 08:35:40 -05:00
Harald Seiler
f62611a9ed imx: spl: Fix typo BMODE_EMI -> BMODE_EIM
The interface for NOR/OneNAND is called "EIM" not "EMI".  Fix this.

Signed-off-by: Harald Seiler <hws@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
2022-02-18 18:12:23 +01:00
Mark Kettenis
02e2588d3f arm: apple: Add RTKit support
Most Apple IOPs run a firmware that is based on what Apple calls
RTKit. RTKit implements a common mailbox protocol.  This code
provides an implementation of the AP side of this protocol,
providing a function to initialize RTKit-based firmwares as well
as a function to do a clean shutdown of this firmware.

Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested on: Macbook Air M1
Tested-by: Simon Glass <sjg@chromium.org>
2022-02-10 16:44:23 -05:00
Mark Kettenis
a4bd5e4120 arm: apple: Change SoC name from "m1" into "apple"
U-Boot is expected to support multiple generations of Apple SoCs
in a single binary with a single defconfig. Therefore it makes
more sense to set SYS_SOC to "apple".

Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
2022-02-10 16:44:23 -05:00
Simon Glass
edca8cf721 Convert CONFIG_SCSI_AHCI_PLAT et al to Kconfig
This converts the following to Kconfig:
   CONFIG_SCSI_AHCI_PLAT
   CONFIG_SYS_SCSI_MAX_SCSI_ID
   CONFIG_SYS_SCSI_MAX_LUN
   CONFIG_SYS_SATA_MAX_DEVICE

Drop CONFIG_SCSI for everything except the sandbox build. We only need
one build for tests.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
2022-02-09 09:16:48 -05:00
Simon Glass
ce30e3ff1e scsi: Drop CONFIG_SYS_SCSI_MAX_DEVICE
This is defined based on two other CONFIGs for all boards except sandbox
and durian.

For sandbox the value does not matter. For durian the value seems
excessive.

Drop the option completely, to simplify configuration and reduce the
number of things we need to convert to Kconfig.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
2022-02-09 09:16:48 -05:00
Keerthy
0197909dd1 arm: mach-omap2: load/start remoteproc IPU1/IPU2
First check the presence of the ipu firmware in the boot partition.
If present enable the ipu and the related clocks & then move
on to load the firmware and eventually start remoteproc IPU1/IPU2.

do_enable_clocks by default puts the clock domains into auto
which does not work well with reset. Hence adding do_enable_ipu_clocks
function.

Signed-off-by: Keerthy <j-keerthy@ti.com>
[Amjad: fix IPU1_LOAD_ADDR and compile warnings]
Signed-off-by: Amjad Ouled-Ameur <aouledameur@baylibre.com>
2022-02-08 09:41:27 -05:00
Angus Ainslie
be63dc7956 mach-imx: iomux-v3: add a define for the SION bit
SION (Software Input On Field) - force the select mode input path

Signed-off-by: Angus Ainslie <angus@akkea.ca>
2022-02-05 15:49:02 +01:00
Dario Binacchi
0c9c5d2ca5 mx6: crm_regs: drop BM_ANADIG_ANA_MISC0_REFTOP_VBGADJ
Commit 97c16dc8bf ("imx: mx6ull: update the REFTOP_VBGADJ setting")
made this macro unused. Then remove it.

Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
2022-02-05 15:49:02 +01:00
Andrey Zhizhikin
1289ff7bd7 imx8m: lock id_swap_bypass bit in tzc380 enable
According to TRM for i.MX8M Nano and Plus, GPR10 register contains lock
bit for TZASC_ID_SWAP_BYPASS bit. This bit is required to be set in
order to avoid AXI bus errors when GPU is enabled on the platform.
TZASC_ID_SWAP_BYPASS bit is alread set for all imx8m applicable
derivatives, but is missing a lock settings to be applied.

Set the TZASC_ID_SWAP_BYPASS_LOCK bit for those derivatives which have
it implemented.

Since we're here, provide also names to bits from TRM instead of using
BIT() macro in the code.

Fixes: deca6cfbf5 ("imx8mn: set BYPASS ID SWAP to avoid AXI bus errors")
Fixes: a07c718129 ("imx8mp: set BYPASS ID SWAP to avoid AXI bus errors")
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Cc: Peng Fan <peng.fan@nxp.com>
2022-02-05 15:49:01 +01:00
Sven Schwermer
0be742d06d imx: Enable ACTLR.SMP in SPL for i.MX6/7
Similar to what has been done before with c5437e5b for u-boot proper, we
enable the SMP bit for SPL as well. This is necessary when SDP booting
straight into Linux, i.e. falcon boot. When SDP boot mode is active, the
ROM code does not set this bit which makes the caches not work once
activated in Linux.

On an i.MX6ULL (528MHz), this reduces a minimal kernel's boot time into
an initramfs shell from ~6.1s down to ~1.2s.

Signed-off-by: Sven Schwermer <sven@svenschwermer.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
2022-02-05 13:38:39 +01:00
Ye Li
dc77d0f9fc imx8ulp: clock: Handle the DDRLOCKED when setting DDR clock
The DDRLOCKED bit in CGC2 DDRCLK will auto lock up and down by HW
according to DDR DIV updating or DDR CLK halt status change. So DDR
PCC disable/enable will trigger the lock up/down flow. We
need wait until unlock to ensure clock is ready.

And before configuring the DDRCLK DIV, we need polling the DDRLOCKED
until it is unlocked. Otherwise writing ti DIV bits will not set.

Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-02-05 13:38:39 +01:00
Alice Guo
0f9b10aaba imx8ulp: clock: Support to enable/disable the ADC1 clock
This patch implements enable_adc1_clk() to enable or disable the ADC1
clock on i.MX8ULP.

Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-02-05 13:38:39 +01:00
Ye Li
3b32010691 imx8ulp: clock: Support to reset DCNano and MIPI DSI
When LPAV is allocated to RTD, the LPAV won't be reset. So we have to
reset DCNano and MIPI DSI in u-boot before enabling the drivers

Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-02-05 13:38:39 +01:00
Ye Li
9c7fbebe5d imx8ulp: Workaround LPOSC_TRIM fuse load issue
8ULP ROM should read the LPOSC trim BIAS fuse to fill the CGC0
LPOSCCTRL[7:0], but it writes a fixed value on A0.1 revision.

A0.2 will fix the issue in ROM. But A0.1 we have to workaround
it in SPL by setting LPOSCCTRL BIASCURRENT again.

Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-02-05 13:38:39 +01:00
Ye Li
bd8b673003 imx8ulp: Fix DCNANO QoS setting
The setting does not have effect because we should set it after
power on the PS16 for NIC AV.

So move it after upower_init which has powered on all PS

Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-02-05 13:38:38 +01:00
Ye Li
9dde390be6 imx8ulp_evk: Control LPI2C0 PCA6416 and TPM0 for display
The board use IO9 of PCA6416 on LPI2C0 and TPM0 for MIPI DSI MUX and
backlight. However the LPI2C0 and TPM0 are M33 resources, in this
patch we simply access them, but this is a temporary solution.
We will modify it when M33 FW changes to set MIPI DSI panel as default
path and enable backlight after reset.

Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-02-05 13:38:38 +01:00
Ye Li
829e06bf41 imx8ulp: clock: Add MIPI DSI clock and DCNano clock
Add the DSI clock enable and disable with PCC reset used.
Add the LCD pixel clock calculation and configuration for DCNano

Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-02-05 13:38:38 +01:00
Ye Li
5ff18da34f imx8ulp: clock: Support LPAV clocks in cgc and pcc
Add the PCC5 clocks support and more LPAV clocks and PLL4 PFD in CGC.

Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-02-05 13:38:38 +01:00
Icenowy Zheng
645ee3c25d sunxi: Add F1C100s DRAM initial support
Add support for F1C100s internal dram controller.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2022-02-04 00:09:57 +00:00
Icenowy Zheng
5d35f0f254 ARM: sunxi: Add clock and uart to sunxi headers
This patch aims to add header files for the suniv.
The header files included add support for uart, and clocks.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2022-02-04 00:09:57 +00:00
Andre Przywara
534b82a1f2 sunxi: move early "SRAM setup" into separate file
Currently we do some magic "SRAM setup" MMIO writes in s_init(), copied
from the original BSP U-Boot. The comment speaks of this being required
before DRAM access gets enabled, but there is no indication that this
would actually be required that early.

Move this out of s_init(), into board_init_f(). Since this actually only
affects a very few older SoCs, the actual code goes into the cpu/armv7
directory, to move it out of the way for all other SoCs.

This also uses the opportunity to convert some #ifdefs over to the fancy
IS_ENABLED() macros used in actual C code.

We keep the s_init() stub around for now, since armv8's lowlevel_init
still relies on it.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
2022-02-04 00:09:57 +00:00
Samuel Holland
efdd656659 sunxi: gpio: Add per-bank drive and pull setters
The GPIO and pinctrl drivers need these setters for pin configuration.
Since they are DM drivers, they should not be using hardcoded base
addresses. Factor out variants of the setter functions which take a
pointer to the GPIO bank's MMIO registers.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2022-01-30 01:25:00 +00:00
Samuel Holland
ac5397a219 sunxi: gpio: Return void from setter functions
The return values of these functions are always zero, and they are
never checked. Since they are not needed, remove them.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2022-01-30 01:04:30 +00:00
Heinrich Schuchardt
185f812c41 doc: replace @return by Return:
Sphinx expects Return: and not @return to indicate a return value.

find . -name '*.c' -exec \
sed -i 's/^\(\s\)\*\(\s*\)@return\(\s\)/\1*\2Return:\3/' {} \;

find . -name '*.h' -exec \
sed -i 's/^\(\s\)\*\(\s*\)@return\(\s\)/\1*\2Return:\3/' {} \;

Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
2022-01-19 18:11:34 +01:00
Ovidiu Panait
2fd81be11c common: board_r: move init_addr_map() to init.h
asm/mmu.h include is currently guarded by CONFIG_ADDR_MAP ifdef because
the header is only present on arm and powerpc. In order to remove the
dependency on this header and the associated ifdef, move init_addr_map()
declaration to init.h, since it is only called during the common init
sequence.

Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
2022-01-18 08:31:02 -05:00
Ovidiu Panait
1b212bb9f4 common: board_r: drop initr_addr_map wrapper
Add a return value to init_addr_map and use it directly in the
post-relocation init sequence, rather than using a wrapper stub.

Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
2022-01-18 08:31:02 -05:00
Tom Rini
be7dbb60c5 Convert CONFIG_SYS_IMMR to Kconfig
This converts the following to Kconfig:
   CONFIG_SYS_IMMR

We do this by consolidating the SYS_IMMR options we have and providing
defaults.

We also, in the few places where M68K was also sharing code with these
platforms, define it within the file to CONFIG_SYS_MBAR to match usage.
This should be cleaned up longer term.

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-12-27 08:41:38 -05:00
Tom Rini
f76750d111 Convert CONFIG_CONS_INDEX et al to Kconfig
This converts the following to Kconfig:
   CONFIG_CONS_INDEX
   CONFIG_DEBUG_UART_CLOCK
   CONFIG_FSL_TZPC_BP147
   CONFIG_GENERIC_ATMEL_MCI
   CONFIG_IDENT_STRING
   CONFIG_LIBATA
   CONFIG_LNX_KRNL_IMG_TEXT_OFFSET_BASE
   CONFIG_LPC32XX_GPIO
   CONFIG_MP
   CONFIG_MPC8XXX_GPIO
   CONFIG_MTD_PARTITIONS
   CONFIG_MVGBE
   CONFIG_MXC_GPIO
   CONFIG_NR_DRAM_BANKS
   CONFIG_OF_BOARD_SETUP
   CONFIG_OF_STDOUT_VIA_ALIAS
   CONFIG_OF_SYSTEM_SETUP
   CONFIG_PREBOOT
   CONFIG_ROCKCHIP_SERIAL
   CONFIG_RTC_ENABLE_32KHZ_OUTPUT
   CONFIG_RTC_MV
   CONFIG_SCSI_AHCI
   CONFIG_SF_DEFAULT_BUS
   CONFIG_SF_DEFAULT_CS
   CONFIG_SF_DEFAULT_SPEED
   CONFIG_SOFT_SPI
   CONFIG_SPI_FLASH_EON
   CONFIG_SPI_FLASH_MACRONIX
   CONFIG_SPI_FLASH_MTD
   CONFIG_SPI_FLASH_SPANSION
   CONFIG_SPI_FLASH_SST
   CONFIG_SPI_FLASH_STMICRO
   CONFIG_SUPPORT_RAW_INITRD
   CONFIG_SYS_ARCH_TIMER
   CONFIG_SYS_BOARD
   CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
   CONFIG_SYS_DCACHE_OFF
   CONFIG_SYS_FDT_SAVE_ADDRESS
   CONFIG_SYS_FLASH_CFI
   CONFIG_SYS_FSL_ERRATUM_ESDHC135
   CONFIG_SYS_HAS_SERDES
   CONFIG_SYS_L2CACHE_OFF
   CONFIG_SYS_LITTLE_ENDIAN
   CONFIG_SYS_LOAD_ADDR
   CONFIG_SYS_MMCSD_FS_BOOT_PARTITION
   CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION
   CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR
   CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR
   CONFIG_SYS_NS16550
   CONFIG_SYS_PLLFIN
   CONFIG_SYS_SPI_U_BOOT_OFFS
   CONFIG_TIMER_SYS_TICK_CH
   CONFIG_USB_EHCI_FSL
   CONFIG_U_QE
   CONFIG_VERSION_VARIABLE

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-12-27 08:41:38 -05:00
Chia-Wei Wang
af6451187c clk: ast2600: Add RSACLK control for ACRY
Add RSACLK enable for ACRY, the HW RSA/ECC crypto engine
of ASPEED AST2600 SoCs.

Signed-off-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
2021-11-17 17:05:00 -05:00
Joel Stanley
4080714f5e clk: ast2600: Add YCLK control for HACE
Add YCLK enable for HACE, the HW hash engine of
ASPEED AST2600 SoCs.

Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
2021-11-17 17:05:00 -05:00
Chia-Wei Wang
3d99be97f1 aspeed: ast2600: Enlarge SRAM size
The AST2600 SRAM has been extended to 88KB since A1
chip revision. This patch updates the SRAM size to
offer more space for early stack/heap use.

Signed-off-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
2021-11-17 17:04:59 -05:00
Tom Rini
d3fb2e3991 Remove CONFIG_SERIAL_MULTI
This symbol has been functionally dead for a long time.  Remove the last
and recent re-introductions of setting it, and update the whitelist so
it will not be re-introduced again.

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-11-12 14:18:17 -05:00
Tom Rini
166a77b34b - DHSOM update:
- Remove nWP GPIO hog
    - Increase SF bus frequency to 50Mhz and enable SFDP
    - Disable video output for DHSOM
    - Disable EFI
    - Enable DFU_MTD support
 - Create include file for STM32 gpio driver private data
 - Split board and SOC STM32MP15 configuration
 - Device tree alignement with v5.15-rc6 for STM32MP15
 - Add binman support for STM32MP15x
 - Normalise newlines for stm32prog
 - Update OTP shadow registers in SPL
 -----BEGIN PGP SIGNATURE-----
 
 iQJQBAABCgA6FiEEXyrViUccKBz9c35Jysd4L3sz/6YFAmGL7ykcHHBhdHJpY2Uu
 Y2hvdGFyZEBmb3NzLnN0LmNvbQAKCRDKx3gvezP/pl1iD/45ARfQCdlq5Iq8VbAf
 NV1TjRguoLU6zR5XhyGAIoDkg87Bsty2ayFyAfz8pHkpEQAFkj9bhiaRZEQj2SSi
 avb2slYGC6iLBEgVBfHjnih4hf0JPTJWcCx+0IO298IknJ49qFfujBFdb3LCbXzt
 zc6QE4mvWWdQHQfNym5UjHqJvI2seHbarEmltAQNn1hqYevFFQYH6vMtgYtZGH18
 c63HeW6uDuGdxGJ9/dzuV/M5bZUAQOI2jJ9OFv7UYQyrzkvLd4M5Qeb52OZ7xNYZ
 xNPCUtNnWUMUnGlpb/ANIUtqBYfcBj1iOMedchLtL9EANObFew/ktk0L1mdjLpQ4
 neB8Im6KmcZkzPyNDs4ha8bSiwOGhrSMg+B49bpp01JvnmzMW3cFtexXL6nKAZyL
 Iohv5MNp7Cf4Fn68v04RBzrAzcvBNPQUnN/19VMN+bqidAzN9y9N7Jc8JgVSOEWN
 OU45X5N840CjqWr8xZ9znICqCdgnY4QtCI9zi6JLHuvWMG3+c10fzyozRfh/OWkE
 3RSyjf9zSjlzYsOEIe8e5Kz/FqLhYqrhdJz2Aqoz5E3k7YQke8WU/OadOU7BWs5U
 QoIMpq8jcAiNZqoMW/V5pxW2nqIB4VIX7LDYuT2TEnVt+hhLP59NtzFTMEjY68Rk
 cH+alF5WHbnqIXgMh5BokUwgxA==
 =lqEG
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-stm32-20211110' of https://source.denx.de/u-boot/custodians/u-boot-stm

- DHSOM update:
   - Remove nWP GPIO hog
   - Increase SF bus frequency to 50Mhz and enable SFDP
   - Disable video output for DHSOM
   - Disable EFI
   - Enable DFU_MTD support
- Create include file for STM32 gpio driver private data
- Split board and SOC STM32MP15 configuration
- Device tree alignement with v5.15-rc6 for STM32MP15
- Add binman support for STM32MP15x
- Normalise newlines for stm32prog
- Update OTP shadow registers in SPL
2021-11-10 14:11:30 -05:00
Patrick Delaunay
56a368f661 gpio: stm32: create include file for driver private data
The stm32 gpio driver private data are not needed in arch include files,
they are not used by code except for stm32 gpio and pincontrol drivers,
using the same IP; the defines for this IP is moved in a new file
"stm32_gpio_priv.h" in driver/gpio.

This patch avoids to have duplicated file gpio.h for each SOC
in MPU directory mach-stm32mp and in each MCU directory arch-stm32*
and allows to remove CONFIG_GPIO_EXTRA_HEADER for all STM32.

Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
2021-11-10 17:03:36 +01:00
Tom Rini
1a77da4b33 Convert CONFIG_SYS_HZ to Kconfig
This converts the following to Kconfig:
	CONFIG_SYS_HZ

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-11-05 11:23:29 -04:00
Mark Kettenis
d520e1fb72 serial: s5p: Add Apple M1 support
Apple M1 SoCs include an S5L UART which is a variant of the S5P
UART.  Add support for this variant and enable it by default
on Apple SoCs.

Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
2021-10-31 08:46:44 -04:00
Michael Walle
60b9b47d29 Revert "arch: arm: use dt and UCLASS_SYSCON to get gic lpi details"
Stop using the device tree as a source for ad-hoc information.

This reverts commit 2ae7adc659.

Signed-off-by: Michael Walle <michael@walle.cc>
[trini: Also make board/broadcom/bcmns3/ns3.c fail clearly now]
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-10-31 08:46:29 -04:00
Tom Rini
79b8849d4c u-boot-imx-20211020
-------------------
 
 First PR from u-boot-imx for 2022.01
 
 CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/9535
 
 - new board: kontron-sl-mx8mm
 - imx8m:
 	- fix secure boot
 - imx ESDHC: fixes
 - i.MX53: Support thum2, bmode and fixes for Menlo board
 	  usbarmory switch to Ethernet driver model
 - imx6 :
 	- DDR calibration for Toradex boards
 - imx7:
 	- Fixes
 - Updated gateworks boards (ventana / venice)
 -----BEGIN PGP SIGNATURE-----
 
 iG0EABECAC0WIQS2TmnA27QKhpKSZe309WXkmmjvpgUCYXAPLA8cc2JhYmljQGRl
 bnguZGUACgkQ9PVl5Jpo76ZZdwCfQBZyd9IWYk3vY0lYgCZsBYl8oXoAn0o9BjVu
 tMJRAcFOLxegM4CJAeqC
 =zg72
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-imx-20211020' of https://source.denx.de/u-boot/custodians/u-boot-imx

u-boot-imx-20211020
-------------------

First PR from u-boot-imx for 2022.01

CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/9535

- new board: kontron-sl-mx8mm
- imx8m:
	- fix secure boot
- imx ESDHC: fixes
- i.MX53: Support thum2, bmode and fixes for Menlo board
	  usbarmory switch to Ethernet driver model
- imx6 :
	- DDR calibration for Toradex boards
- imx7:
	- Fixes
- Updated gateworks boards (ventana / venice)

# gpg verification failed.
2021-10-20 14:24:09 -04:00
Tom Rini
d990f7d75d Merge tag 'u-boot-rockchip-20211015' of https://source.denx.de/u-boot/custodians/u-boot-rockchip
- Fix for Rockchip mmc HS400 mode;
- Fix for px30 board Odroid Go;
- rockchip_sfc update;
- rk3568 clk update;
- doc fix;
2021-10-17 21:13:49 -04:00
Tom Rini
6a86f12126 Merge branch 'master' of https://source.denx.de/u-boot/custodians/u-boot-tegra
On merge, fixup order of fdtdec_add_reserved_memory parameters in
arch/arm/cpu/armv8/fsl-layerscape/soc.c

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-10-15 18:30:33 -04:00
Elaine Zhang
f2cdd44adb clk: rockchip: rk3568: update clks
fix up ppll init freq.
support tclk_emmc.
add freq (26M) for mmc device.
fix up the sfc clk rate unit error.

Change in V2:
remove change id.

Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2021-10-15 20:57:31 +08:00
Patrick Delaunay
ff07cc9ed1 scripts: remove some configs in config_whitelist.txt
Remove some config finishing by _ badly added by
scripts/build-whitelist.sh when joker is used in comments.

for example:
  doc/uImage.FIT/command_syntax_extensions.txt:
     ... #ifdef CONFIG_OF_*  |	...

  cmd/nvedit.c:# error Define one of CONFIG_ENV_IS_IN_{EEPROM| \
     FLASH|MMC|FAT|EXT4|\

Remove also configs only used in comments:
- CONFIG_BOOGER in include/linux/kconfig.h
- CONFIG_COMMANDS
- CONFIG_INIT_IGNORE_ERROR
- CONFIG_REG_*
- CONFIG_HOTPLUG : drivers/watchdog/omap_wdt.c:18

Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
2021-10-15 07:55:17 -04:00
Thierry Reding
77409c7f83 ARM: tegra: Refactor DT update helpers
Rather than duplicate the Ethernet MAC address and carveout updating
code for each board, move it to a common location and make it more
reusable.

Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2021-10-13 14:18:30 -07:00
Tom Rini
776bf6a545 - Disable ATAGS for STM32 MCU and MPU boards
- Disable bi_boot_params for STM32 MCU and MPU boards
 - Update stm32-usbphyc node management
 - Convert CONFIG_STM32_FLASH to Kconfig for STM32 MCU boards
 - Convert some USB config flags to Kconfig for various boards
 - Convert CONFIG_BOOTCOMMAND flag to Kconfig for STM32 F429 board
 - Remove specific CONFIG_STV0991 flags
 - Remove unused CONFIG_USER_LOWLEVEL_INIT flag
 - Add ofdata_to_platdata() callback for stm32_spi driver
 - Update for stm32f7_i2c driver
 - Remove gpio_hog_probe_all() from STM32 MP1 board
 - Fix bind command
 -----BEGIN PGP SIGNATURE-----
 
 iQJQBAABCgA6FiEEXyrViUccKBz9c35Jysd4L3sz/6YFAmFlgsIcHHBhdHJpY2Uu
 Y2hvdGFyZEBmb3NzLnN0LmNvbQAKCRDKx3gvezP/plnND/4q9HSlvddybIPjBHlW
 rXz1ISwj8JZPp7R4MJcB4RiHofYZzjTXx3dDYUif6oQMpCDp64KPfcUDW0kaq8U7
 ZFwJvt59boV1XWlonIXMb3gAkY6gFa5PnYAE/YXEqKvPPvUb7FkT7BWxm4LxCGsj
 mEmboR8u87s6e4ZP03HJsSVa5FnNwJUZU8b+58Vxp10YC0PPf7kpmgCucDhrghvY
 TORlk259KUFoZXz4J4My0VzDdxE05gDqq1m6Xw1CzqcUbGysMvjNEHlxGdYbWD/U
 maamP19DUmKUREmpj3kO/JZvacLJlQP/mdGJ0OWKNbIr/3ha4dYagxDoRodEVo0m
 DYaaVPGvG24G78d5meB2q9wT0aGdTyaqm+XRBQMvMN2LlaGmu9duA1t6yBuyMcFk
 BeA7d0eHMo1ezD9FFZMxwIOAWhJlcYQEAMFhUwkR1B322w0NU4nbl9KRCGuGV2Zp
 ZFQV4BoMvb0NwAdo66xwZ+gSq4Wp1y46VM6x2Mw52v2F4p3teeAqR906TdQVYO8+
 hlYChO9+qK4JO7LPX/5wQ4FIzcq1HnTzTpuOSf28hsemiPMu0OkAQv1J7DohNZix
 wELBA+ZIjGXksmDTPjpXg5CSvVALa/l2G816hp7/XTJ1XRBSz/pzjhp5rwm42zmw
 x7EPnwzpAlQCSqTQ0sgO+fgoRA==
 =S4kl
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-stm32-20211012' of https://source.denx.de/u-boot/custodians/u-boot-stm

- Disable ATAGS for STM32 MCU and MPU boards
- Disable bi_boot_params for STM32 MCU and MPU boards
- Update stm32-usbphyc node management
- Convert CONFIG_STM32_FLASH to Kconfig for STM32 MCU boards
- Convert some USB config flags to Kconfig for various boards
- Convert CONFIG_BOOTCOMMAND flag to Kconfig for STM32 F429 board
- Remove specific CONFIG_STV0991 flags
- Remove unused CONFIG_USER_LOWLEVEL_INIT flag
- Add ofdata_to_platdata() callback for stm32_spi driver
- Update for stm32f7_i2c driver
- Remove gpio_hog_probe_all() from STM32 MP1 board
- Fix bind command

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-10-12 12:01:00 -04:00
Tom Rini
2aab77f726 Merge https://source.denx.de/u-boot/custodians/u-boot-sunxi
The bulk of it is Samuel's DM_I2C rework, which removes the nasty I2C
deprecation warnings for most 32-bit boards. It also includes some
smaller refactorings that pave the way for more changes, mostly driven
by needing to support the Allwinner RISC-V SoC later on.

Board wise we gain support for the FriendlyARM NanoPi R1S H5 router
board and official Pinetab support.

Build-tested for all 160 sunxi boards, and boot tested on a A64, A20,
H3, H6, and H616 board. USB, SD card, eMMC, and Ethernet all work there
(where applicable).
2021-10-12 11:45:00 -04:00
Dario Binacchi
165e8fe5db clk: ti: add am33xx/am43xx spread spectrum clock support
The patch enables spread spectrum clocking (SSC) for MPU and LCD PLLs.
As reported by the TI spruh73x/spruhl7x RM, SSC is only supported for
the DISP/LCD and MPU PLLs on am33xx/am43xx. SSC is not supported for
DDR, PER, and CORE PLLs.

Calculating the required values and setting the registers accordingly
was taken from the set_mpu_spreadspectrum routine contained in the
arch/arm/mach-omap2/am33xx/clock_am33xx.c file of the u-boot project.

In locked condition, DPLL output clock = CLKINP *[M/N]. In case of
SSC enabled, the reference manual explains that there is a restriction
of range of M values. Since the clk_ti_am3_dpll_round_rate() attempts
to select the minimum possible N, the value of M obtained is not
guaranteed to be within the range required. With the new "ti,min-div"
parameter it is possible to increase N and consequently M to satisfy the
constraint imposed by SSC.

Link: https://lore.kernel.org/r/20210606202253.31649-6-dariobin@libero.it
Signed-off-by: Dario Binacchi <dariobin@libero.it>
2021-10-11 14:27:32 -04:00
Samuel Holland
8fe8ff3411 sunxi: gpio: Remove bank-specific size macros
Since the beginning, all banks have had space for 32 pins, even when
not all pins were implemented. Let's use a single constant for the GPIO
bank size here, like the GPIO driver is already doing.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-10-11 10:46:44 +01:00
Samuel Holland
4d9958b642 sunxi: gpio: Remove name_to_gpio macro
This clarifies which callers must be updated to complete the DM_GPIO
conversion.

The only remaining caller of name_to_gpio in generic code is inside the
!DM_GPIO block in cmd/gpio.c. DM_GPIO is always selected on sunxi, so
that code cannot be reached. And after this commit, there are only two
remaining implementations of name_to_gpio.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-10-11 10:46:44 +01:00
Samuel Holland
14c8c631e9 gpio: sunxi: Remove the sunxi_name_to_gpio_bank function
The only caller of this function was the MMC pinmux code, which used it
to parse a string given from a Kconfig symbol. As the Kconfig symbol has
been converted to a Boolean, this function is no longer needed.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-10-11 10:46:44 +01:00
Samuel Holland
dda9fa734f sunxi: Simplify MMC pinmux selection
Only one board, Yones Toptech BD1078, actually uses a non-default MMC
pinmux. All other uses of these symbols select the default value or an
invalid value. To simplify things, remove support for the unused pinmux
options, and convert the remaining option to a Boolean.

This allows the pinmux to be chosen by the preprocessor, instead of
having the code parse a string at runtime (for a build-time option!).
Not only does this reduce code size, but it also allows this Kconfig
option to be used in a table-driven DM pinctrl driver.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-10-11 10:46:44 +01:00
Samuel Holland
21d314a661 clk: sunxi: Move header out of arch directory
The CCU header is only used by the DM drivers, not any platform code.
Its current location adds an artificial dependency on CONFIG_ARM and
ARCH_SUNXI, which will be problematic when adding the CCU driver for
a RISC-V sunxi platform.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-10-11 10:46:44 +01:00
Patrick Delaunay
20a3969d33 stv0991: remove specific CONFIG_STV0991 configs
Remove the following STV0991 specific configs:
- CONFIG_STV0991 (never used, only defined in CONFIG_SYS_EXTRA_OPTIONS)
- CONFIG_STV0991_HZ (replaced by generic CONFIG_SYS_HZ)
- CONFIG_STV0991_HZ_CLOCK (replaced by generic CONFIG_SYS_HZ_CLOCK)

This patch allows to reduce the file config_whitelist.txt.

Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
2021-10-08 08:30:18 +02:00
Ye Li
ae3f752919 arm: imx8m: Fix pad DSE issue for i.MX8MM/MN/MP
According to 8MM/MN/MP reference manual, their pad registers only have
4 valid DSE values. And DSE2 and DSE4 are different with current
definitions in iomux-v3.h. Fix the issue to align with manual.

Signed-off-by: Ye Li <ye.li@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
2021-10-07 16:53:50 +02:00
Tom Rini
1cefed1e39 nand.h: Cleanup linux/mtd/rawnand.h usage
We only include <linux/mtd/rawnand.h> in <nand.h> for the forward
declaration of struct nand_chip, so do that directly.  Then, include
<linux/mtd/rawnand.h> where required directly.

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-10-06 09:16:23 -04:00
Tom Rini
9d9f59dd0a Convert CONFIG_SYS_NAND_BAD_BLOCK_POS to Kconfig
This converts the following to Kconfig:
   CONFIG_SYS_NAND_BAD_BLOCK_POS

In order to do this, introduce a choice for HAS_LARGE/SMALL_BADBLOCK_POS
as those are the only valid values.  Use LARGE as the default as no
in-tree boards use SMALL, but it is possible.

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-10-06 09:16:23 -04:00
Tom Rini
8db73ec106 Convert CONFIG_SYS_NAND_PAGE_COUNT to Kconfig
This converts the following to Kconfig:
   CONFIG_SYS_NAND_PAGE_COUNT

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-10-06 09:16:23 -04:00
Tom Rini
a0de075392 Convert CONFIG_SPL_NAND_LOAD et al to Kconfig
This converts the following to Kconfig:
   CONFIG_SPL_NAND_LOAD
   CONFIG_SYS_NAND_BLOCK_SIZE
   CONFIG_SYS_NAND_PAGE_SIZE
   CONFIG_SYS_NAND_OOBSIZE

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-10-06 09:16:23 -04:00
Tom Rini
8ba59608dc arm: Remove zmx25 board and ARCH_MX25
This board has not been converted to CONFIG_DM by the deadline.
Remove it.  As this is the last ARCH_MX25 platform, remove those
references as well.

Cc: Matthias Weisser <weisserm@arcor.de>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-10-01 21:08:18 -04:00
Tom Rini
d9be8606bb arm: Remove aspenite board
This board has not been converted to CONFIG_DM by the deadline.
Remove it.  As this is the last armada100 platform, remove that support
as well.

Cc: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-10-01 12:10:09 -04:00
Tom Rini
14b38cb0c2 arm: Remove flea3 board
This board has not been converted to CONFIG_DM by the deadline.
Remove it.  As this is the last mx35 platform, remove that support as
well.

Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2021-10-01 12:08:19 -04:00
Wolfgang Denk
0cf207ec01 WS cleanup: remove SPACE(s) followed by TAB
Signed-off-by: Wolfgang Denk <wd@denx.de>
2021-09-30 09:08:16 -04:00
Wolfgang Denk
0a50b3c97b WS cleanup: remove trailing white space
Signed-off-by: Wolfgang Denk <wd@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
2021-09-30 08:08:56 -04:00
Wolfgang Denk
66356b4c06 WS cleanup: remove trailing empty lines
Signed-off-by: Wolfgang Denk <wd@denx.de>
2021-09-30 08:08:56 -04:00
Patrick Delaunay
6493fa4c3d arm: use CONFIG_SUPPORT_PASSING_ATAGS
Simplify the bootm and the spl code by using the new config
CONFIG_SUPPORT_PASSING_ATAGS.

Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2021-09-24 14:30:46 -04:00
Stefan Roese
4e062fc955 arm64: Kconfig: Enable usage of optimized memset/memcpy/memmove
This patch enables the use of the optimized memset(), memmove() &
memcpy() versions recently added on ARM64.

Please note that these optimized functions are now only enabled for
recent GCC versions (>= 9.4), as earlier GCC versions throw these
errors:

aarch64-linux-ar: warning: arch/arm/lib/memset-arm64.o: unsupported GNU_PROPERTY_TYPE (5) type: 0xc0000000
...

Signed-off-by: Stefan Roese <sr@denx.de>
[trini: Make this default to off as it causes problems on some platforms still]
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-09-24 07:49:16 -04:00