OPOS6UL is an i.MX6UL based SoM with 256MB RAM, 4GB eMMC and an ethernet
phy. OPOS6ULDev is carrier board for the OPOS6UL.
U-Boot SPL 2017.03-rc3-00002-g5085c26 (Mar 07 2017 - 09:48:09)
Trying to boot from MMC1
U-Boot 2017.03-rc3-00002-g5085c26 (Mar 07 2017 - 09:48:09 +0100)
CPU: Freescale i.MX6UL rev1.0 528 MHz (running at 396 MHz)
CPU: Industrial temperature grade (-40C to 105C) at 40C
Reset cause: POR
Model: Armadeus Systems OPOS6UL SoM on OPOS6ULDev board
DRAM: 256 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Video: 800x480x18
In: serial
Out: serial
Err: serial
Net: FEC [PRIME]
Hit any key to stop autoboot: 0
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Today, we have cases where we wish to build all of U-Boot in Thumb2 mode for
various reasons. We also have cases where we only build SPL in Thumb2 mode due
to size constraints and wish to build the rest of the system in ARM mode. So
in this migration we introduce a new symbol as well, SPL_SYS_THUMB_BUILD to
control if we build everything or just SPL (or in theory, just U-Boot) in
Thumb2 mode.
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
CONFIG_SPL_ABORT_ON_RAW_IMAGE causes SPL to abort and move on when it
encounters RAW images, express this same functionality as a positive
option enabling support for RAW images: CONFIG_SPL_RAW_IMAGE_SUPPORT
Also move uses of this to defconfigs.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Rework Kconfig logic a little, move to common/spl/Kconfig]
Signed-off-by: Tom Rini <trini@konsulko.com>
This includes support for rk3188 from Heiko Stübner and and rk3328 from
Kever Yang. Also included is SPL support for rk3399 and a fix for
rk3288 to get it booting again (spl_early_init()).
Boards with an apparent need for the md5sum command had the connected
config symbol defined in their board header file.
Move this over to the respective defconfig files now that md5sum is
configured via Kconfig.
(This is a manual effort, which differs from moveconfig.py, not sure
who is right here. Boards except sandbox loose the md5sum command with
moveconfig.py, though it was explicitly mentioned in their config.h's)
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: migrate stih410-b2260]
Signed-off-by: Tom Rini <trini@konsulko.com>
FIT images require MD5 support to verify image checksums. So far this
was expressed by defining a CPP symbol in image.h. Since MD5 is now a
first class Kconfig citizen, express that in Kconfig instead.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds support for TQMa6DL using i.MX6DL and 1GiB DRAM
Since The module will use the same devicetree, we patch
the ram size in ft_board_setup.
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
We have a Kconfig name for the module types. Let's Use it.
Some feature selections and configurations are based on the
module. Module selection selects the CPU type.
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
Let the runtime code can set the mmcdev and mmcroot based
on the devno using mmc_get_env_dev instead of defining
separately in build-time configs using mmc_late_init func.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add runtime, modeboot env which is setting mmcboot based
on the bootdevice so-that conditional macros for MMC via
CONFIG_BOOTCOMMAND should be avoided in config files.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Boot from eMMC:
--------------
U-Boot SPL 2017.01-00318-g8e243f8 (Jan 26 2017 - 11:53:21)
Trying to boot from MMC2
U-Boot 2017.01-00318-g8e243f8 (Jan 26 2017 - 11:53:21 +0100)
CPU: Freescale i.MX6D rev1.2 at 792 MHz
Reset cause: POR
Model: Engicam i.CoreM6 Quad/Dual RQS Starter Kit
DRAM: 512 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
switch to partitions #0, OK
mmc1(part 0) is current device
Net: No ethernet found.
Hit any key to stop autoboot: 0
Booting from mmc ...
switch to partitions #0, OK
mmc1(part 0) is current device
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Let the runtime code can set the mmcdev and mmcroot based
on the devno using mmc_get_env_dev instead of defining
separately in build-time configs using mmc_late_init func.
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add runtime, modeboot env which is setting mmcboot, or
nandboot based on the bootdevice so-that conditional
macros b/w MMC and NAND for CONFIG_BOOTCOMMAND should
be avoided in config files.
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add config options for booting Linux from NAND in UBI format.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Boot from MMC:
-------------
U-Boot SPL 2017.01-rc2-gba3c151-dirty (Jan 02 2017 - 16:59:33)
Trying to boot from MMC1
U-Boot 2017.01-rc2-gba3c151-dirty (Jan 02 2017 - 16:59:33 +0100)
CPU: Freescale i.MX6UL rev1.1 528 MHz (running at 396 MHz)
CPU: Industrial temperature grade (-40C to 105C) at 33C
Reset cause: POR
Model: Engicam Is.IoT MX6UL Starterkit
DRAM: 512 MiB
MMC: FSL_SDHC: 0
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot: 0
isiotmx6ul>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
USDHC base address will assigned by SPL using fsl_esdhc_initialize
and u-boot with devicetree, hence no remove base address assignment
in config files.
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Enable MMC support.
The fsl sdhc driver needs regulator to enable power, so enable
regulator support.
And bootcmd and more env.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Add i.MX7ULP support.
The buadrate calculation on i.MX7ULP is different,so add a new setbrg
function for i.MX7ULP.
Add a enum lpuart_devtype for runtime check for different platforms.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Shaohui Xie <Shaohui.Xie@nxp.com>
Cc: Alison Wang <b18965@freescale.com>
Commit e856bdcfb4 ("flash: complete CONFIG_SYS_NO_FLASH move with renaming")
obsoleted the CONFIG_SYS_NO_FLASH option, which still is in our
rk3188_common.h header, resulting in warnings like
The following new ad-hoc CONFIG options were detected:
CONFIG_SYS_NO_FLASH
So also drop it from the rk3188 header.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
Documentation says that we're returning true/false, not 1/0 so adapt
the function to return actual booleans.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
evb-rk3328 is an evb from Rockchip based on rk3328 SoC:
- 2 USB2.0 Host port;
- 1 USB3.0 Host port;
- 1 HDMI port;
- 2 10/100M eth port;
- 2GB ddr;
- 16GB eMMC;
- UART to USB debug port;
Signed-off-by: William Zhang <william.zhang@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
RK3328 is a SoC from Rockchip with quad-core Cortex-A53 CPU.
It supports two USB2.0 EHCI ports. Other interfaces are very
much like RK3288, the DRAM are 32bit width address and support
address from 0 to 4GB-16MB range.
Signed-off-by: William Zhang <william.zhang@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add empty arch/arm/mach-rockchip/rk3328/Kconfig to avoid build error:
Signed-off-by: Simon Glass <sjg@chromium.org>
Add dts binding header for rk3328, files origin from kernel.
Signed-off-by: William Zhang <william.zhang@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Enable all the CONFIGs which need by SPL.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Added rockchip tag:
Drop CONFIG_ROCKCHIP_DWMMC for now due to build error:
Move changes to arch/arm/mach-rockchip/Kconfig to this patch:
Signed-off-by: Simon Glass <sjg@chromium.org>
Add SPL support for rk3399, default with of-platdata enabled.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Drop Kconfig changes to fix build error:
Signed-off-by: Simon Glass <sjg@chromium.org>
We are using wrong mmc instance as boot target device now. below Jaehoon Chung's
patch use mmc alias which correct it. That make tinker board can not find mmc
device. So give it correct mmc device instance.
commit 02ad33aa3a
Author: Jaehoon Chung <jh80.chung@samsung.com>
Date: Thu Feb 2 13:41:14 2017 +0900
mmc: mmc-uclass: use the fixed devnum with alias node
Signed-off-by: Eddie Cai <eddie.cai.linux@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add the core architecture code for the rk3188.
It doesn't support the SPL yet, as because of some
unknown error it doesn't start yet.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
Drop these defines from rk3188_common.h
CONFIG_GENERIC_MMC, CONFIG_BOUNCE_BUFFER, CONFIG_DOS_PARTITION
CONFIG_PARTITION_UUIDS, CONFIG_CMD_PART:
Signed-off-by: Simon Glass <sjg@chromium.org>
Bring in required device clock binding files from Linux.
The clock trees for rk3066 and rk3188 are largely similar, which makes
them share the common parts in a shared header. While we focus on rk3188
for now, bring in both headers already for completeness sake.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
Right now the u-boot,dm-pre-reloc flag will make each marked node
always appear in both spl and tpl. But systems needing an additional
tpl might have special constraints for each, like the spl needing to
be very tiny.
So introduce two additional flags to mark nodes for only spl or tpl
environments and introduce a function dm_fdt_pre_reloc to automate
the necessary checks in code instances checking for pre-relocation
flags.
The behaviour of the original flag stays untouched and still marks
a node for both spl and tpl.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
At present malloc_base/_limit/_ptr are not initialised in spl_init() when
we call spl_init() in board_init_f(). This is due to a recent change aimed
at avoiding overwriting the malloc area set up on some boards by
spl_relocate_stack_gd().
However if CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN is not defined, we now
skip setting up the memory area in spl_init() which is obviously wrong.
To fix this, add a new function spl_early_init() which can be called in
board_init_f().
Fixes: b3d2861e (spl: Remove overwrite of relocated malloc limit)
Signed-off-by: Eddie Cai <eddie.cai.linux@gmail.com>
Rewrote spl_{,early_}init() to avoid duplicate code:
Rewrite/expand commit message:
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Eddie Cai <eddie.cai.linux@gmail.com>
- Move to DM clk driver
- Add clk support for zynq_sdhci
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAljKWVcACgkQykllyylKDCEsgACfey0mgRaGVMLSxMMCGgJQIK70
/oYAn3raqYrJ2e2fsjb1B5WodYcDe8L5
=JYC5
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2017.05' of git://www.denx.de/git/u-boot-microblaze
Xilinx changes for v2017.05
- Move to DM clk driver
- Add clk support for zynq_sdhci
ISEE's U-Boot and Linux are using 1bit ECC scheme, while we
switched to 8bit ECC to fullfill flash specification requirements.
However when trying to run U-Boot on board with 1bit ECC'd data
on flash, UBI code takes several minutes to pass scan as reading
of every block ends with ecc error (which is also printed on
console).
So, until proper solution is developed, disable environment
alltogether.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
This is a 96Board compliant board based on STiH410 SoC:
- 1GB DDR
- On-Board USB combo WiFi/Bluetooth RTL8723BU
with PCB soldered antenna
- Ethernet 1000-BaseT
- SATA
- HDMI
- 2 x USB2.0 type A
- 1 x USB2.0 type micro-AB
- SD card slot
- High speed connector (SD/I2C/USB interfaces)
- Low speed connector (UART/I2C/GPIO/SPI/PCM interfaces)
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This device tree has been extracted from v4.9 kernel
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Raw uboot image is used in place of FIT image in secure boot.
The maximum allocated size of raw u-boot bin is 1MB in memory map.
Hence , CONFIG_SYS_MONITOR_LEN has been modified to 1 MB.
The bootscript (BS_ADDR) and its header (BS_HDR_ADDR) offset on
MMC have also been modified to accommodate the increase in uboot size.
Signed-off-by: Vinitha Pillai-B57223 <vinitha.pillai@nxp.com>
Reviewed-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Remove the DDR interactive debugging to reduce the size of spl image.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This moves all of the current ARM errata from various header files and in to
Kconfig. This allows for a minor amount of cleanup as we had some instances
where both a general common header file was enabling errata as well as the
board config. We now just select these once at the higher level in Kconfig
Signed-off-by: Tom Rini <trini@konsulko.com>
In some cases this is absolutely required, so select this for some secure
features. This also requires migration of RSA_FREESCALE_EXP
Cc: Ruchika Gupta <ruchika.gupta@nxp.com>
Cc: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Cc: Naveen Burmi <NaveenBurmi@freescale.com>
Cc: Po Liu <po.liu@freescale.com>
Cc: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Cc: Priyanka Jain <Priyanka.Jain@freescale.com>
Cc: Sumit Garg <sumit.garg@nxp.com>
Cc: Shaohui Xie <Shaohui.Xie@freescale.com>
Cc: Chunhe Lan <Chunhe.Lan@freescale.com>
Cc: Feng Li <feng.li_2@nxp.com>
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Mingkai Hu <Mingkai.Hu@freescale.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Saksham Jain <saksham.jain@nxp.freescale.com>
Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
For the memory footprint reason, the Boot ROM can not load the ARM
Trusted Firmware BL1 directly when Trusted Board Boot is enabled.
The second stage loader is Socionext's own firmware, so rename it
for clarification.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
need to add before div in mmc update scripts. Otherwise we could
write one block more ba acident
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
Playing with USB-to-Ethernet dongles it turns out,
that these will not work with special settings
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
depending on the use case different CMA sizes are
needed for linux. Add env var to enable passing CMA size
via kernel command line
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
The fdt_addr and ramdisk_addr_r are currently both defined to
0x83000000 and that's not going to work well for anyone. Move
the ramdisk_addr_r to 0x84000000.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Standard boot processes including distro boot generally expect the
default console to be defined.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
Added SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION and
SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION to Kconfig.
Due to SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION being moved to
Kconfig the board defconfigs for db-88f6820-gp_defconfig
kc1_defconfig and sniper_defconfig need to be updated.
Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
the socfpga bootrom supports mmc booting from either a raw image
starting at 0x0, or from a partition of type 0xa2. This patch
adds support for locating the boot image in the first type 0xa2
partition found.
Assigned a partition number of -1 will cause a search for a
partition of type CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION_TYPE
and use it to find the u-boot image
Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
Move the zynq to clock framework and remove unused functions as well as
the CONFIG_ZYNQ_PS_CLK_FREQ configuration.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
We repeated partial moves for CONFIG_SYS_NO_FLASH, but this is
not completed. Finish this work by the tool.
During this move, let's rename it to CONFIG_MTD_NOR_FLASH.
Actually, we have more instances of "#ifndef CONFIG_SYS_NO_FLASH"
than those of "#ifdef CONFIG_SYS_NO_FLASH". Flipping the logic will
make the code more readable. Besides, negative meaning symbols do
not fit in obj-$(CONFIG_...) style Makefiles.
This commit was created as follows:
[1] Edit "default n" to "default y" in the config entry in
common/Kconfig.
[2] Run "tools/moveconfig.py -y -r HEAD SYS_NO_FLASH"
[3] Rename the instances in defconfigs by the following:
find . -path './configs/*_defconfig' | xargs sed -i \
-e '/CONFIG_SYS_NO_FLASH=y/d' \
-e 's/# CONFIG_SYS_NO_FLASH is not set/CONFIG_MTD_NOR_FLASH=y/'
[4] Change the conditionals by the following:
find . -name '*.[ch]' | xargs sed -i \
-e 's/ifndef CONFIG_SYS_NO_FLASH/ifdef CONFIG_MTD_NOR_FLASH/' \
-e 's/ifdef CONFIG_SYS_NO_FLASH/ifndef CONFIG_MTD_NOR_FLASH/' \
-e 's/!defined(CONFIG_SYS_NO_FLASH)/defined(CONFIG_MTD_NOR_FLASH)/' \
-e 's/defined(CONFIG_SYS_NO_FLASH)/!defined(CONFIG_MTD_NOR_FLASH)/'
[5] Modify the following manually
- Rename the rest of instances
- Remove the description from README
- Create the new Kconfig entry in drivers/mtd/Kconfig
- Remove the old Kconfig entry from common/Kconfig
- Remove the garbage comments from include/configs/*.h
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The kernel partition in QSPI is 0x440000 large, not 0x400000. Fix this
in the environment, otherwise the kernel will fail to boot if it occupies
more space.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Miniarm is the internal project code. Now it is officially named Tinker board.
So rename it.
Signed-off-by: Eddie Cai <eddie.cai@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Keep it same with other boards otherwise i have to write special script for it..
Signed-off-by: Jacob Chen <jacob2.chen@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Albeit it's a typo, neither CONGIG_CMD_STORAGE nor CONFIG_CMD_STORAGE
are used anywhere, so remove the define from the board configs.
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
CONFIG_CMD_ZIP is not defined by any board. I am moving
CONFIG_CMD_UNZIP to defconfig files except UniPhier SoC family.
I am the maintainer of UniPhier platform, so I know "select CMD_UNZIP"
is better for this platform.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Ryan Harkin <ryan.harkin@linaro.org>
Tested-by: Ryan Harkin <ryan.harkin@linaro.org>
Now that we have a Kconfig for the API, convert the two boards that
are using this to Kconfig and remove CONFIG_API from the whitelist.
Signed-off-by: Emmanuel Vadot <manu@bidouilliste.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The previous commit ("add a new command to show .config contents")
improves the basic infrastructure of "embed a compressed file into
the U-Boot image, and print it by a command". The same pattern for
the "license" command.
This commit reworks the command to improve the following:
[1] Improve log style
Kbuild style log
GZIP cmd/license_data.gz
CHK cmd/license_data_gz.h
UPD cmd/license_data_gz.h
CHK cmd/license_data_size.h
UPD cmd/license_data_size.h
instead of the bare Make log:
cat ./Licenses/gpl-2.0.txt | gzip -9 -c | \
tools/bin2header license_gzip > ./include/license.h
[2] Collect related code into the "cmd" directory
Prior to this commit, the license.h was created by tools/Makefile,
placed under the "include" directory, included from cmd/license.c,
and deleted by the top-level Makefile. It is not a good idea to
scatter related code.
[3] Drop the fixed-malloc size LICENSE_MAX
Just allocate the minimum required size of buffer because we know
the size of the original gpl-2.0.txt.
[4] Fix more issues
Terminate the buffer with zero to prevent puts() from over-running.
Add "static" to do_license.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present devices use a simple integer offset to record the device tree
node associated with the device. In preparation for supporting a live
device tree, which uses a node pointer instead, refactor existing code to
access this field through an inline function.
Signed-off-by: Simon Glass <sjg@chromium.org>
This patch enables crc8 to be used from within the tools directory using
u-boot/crc.h.
Signed-off-by: Olliver Schinagl <o.schinagl@ultimaker.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
There are various places where the ethernet device name is defined to
several different sizes. Lets add a define and start using it.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
In u-boot printf has been extended with the %pM formatter to allow
printing of MAC addresses. However buffers that want to store a MAC
address cannot safely get the size. Add a define for this case so the
string of a MAC address can be reliably obtained.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Commit 674bb24982 ("net: cosmetic: Replace magic numbers in arp.c with
constants") introduced a nice define to replace the magic value 6 for
the ethernet hardware address. Replace more hardcoded instances of 6
which really reference the ARP_HLEN (iow the MAC/Hardware/Ethernet
address).
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
If SPL is used we want to use the generic SPL framework and boot
from SPI via a board-specific means. Add these options to the
board config file.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
If SPL is used we want to use the generic SPL framework and boot from SPI
via a board-specific means. Add these options to the board config file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
We should use unsigned long rather than u32 for addresses. Update this so
that the table-generation code builds correctly on 64-bit machines.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
PPA binary needs to be relocated on secure DDR, hence marking out
a portion of DDR as secure if CONFIG_SYS_MEM_RESERVE_SECURE flag
is set
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Abhimanyu Saini <abhimanyu.saini@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch adds a function to the TPM library, which allows U-Boot to
flush resources, e.g. keys, from the TPM.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Make the naming scheme consistent; all SDHCI-base drivers prefixed
with CONFIG_MMC_SDHCI_.
While we are here, add "depends on ARCH_ZYNQ || ARCH_ZYNQMP".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Now, CONFIG_GENERIC_MMC seems equivalent to CONFIG_MMC.
Let's create an entry for "config GENERIC_MMC" with "default MMC",
then convert all macro defines in headers to Kconfig. Almost all
of the defines will go away.
I see only two exceptions:
configs/blanche_defconfig
configs/sandbox_noblk_defconfig
They define CONFIG_GENERIC_MMC, but not CONFIG_MMC. Something
might be wrong with these two boards, so should be checked later.
Anyway, this is the output of the moveconfig tool.
This commit was created as follows:
[1] create a config entry in drivers/mmc/Kconfig
[2] tools/moveconfig.py -r HEAD GENERIC_MMC
[3] manual clean-up of garbage comments in doc/README.* and
include/configs/*.h
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Currently, SPL (u-boot-spl.bin) and U-Boot (u-boot.bin) are stored
in non-volatile devices, and some environments are defined to update
the images easily.
When ARM Trusted Firmware is fully used, SPL is not used. U-Boot
proper is contained as BL33 into FIP (Firmware Image Package), which
is standard container used by ATF. Allow to use it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The Boot ROM supports authentication feature to prevent malformed
software from being run on products. The signature is added at the
tail of the second stage loader (= SPL in U-boot terminology).
The size of the second stage loader was 64KB, and it was consistent
across SoCs. The situation changed when LD20 SoC appeared; it loads
80KB second stage loader, and it is the only exception.
Currently, CONFIG_SPL_PAD_TO is set to 64KB and U-Boot proper is
loaded from the 64KB offset of non-volatile devices. This means the
signature of LD20 SoC (located at 80KB offset) corrupts the U-Boot
proper image.
Let's move the U-Boot proper image to 128KB offset. It uses 48KB
for nothing but padding, and we could actually locate the U-Boot
proper at 80KB offset. However, the power of 2 generally seems a
better choice for the offset address.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
When ARM Trusted Firmware is used, bl1.bin + fip.bin exceeds 512KB,
so the boot image and the current environment area will overlap.
Move the environment storage to 1MB offset.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The boot_ramdisk_high() checks the environment "initrd_high" and,
if it is set to (ulong)-1, skip the initrd relocation. This is
useful for faster booting when we know the initrd is already located
within the reach of the kernel.
Change "norboot" to copy images in order to make it work without
depending on the automatic relocation.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The ARM64 Linux raw image now amounts to 15MB and it is getting
bigger and bigger. Using Image.gz saves about 8MB. The cost of
unzip is smaller than what we get by saving the kernel loading
from non-volatile devices.
The ARM32 Linux still uses zImage, a self-decompressor image,
so it should not be affected.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
For clarification, move CONFIG symbols that affect SPL building
into a single place. Drop #ifdef CONFIG_SPL ... #endif since it is
harmless to define CONFIG_SPL_... during U-Boot proper building.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
U-Boot needs to set up available memory area(s) in dram_init() and
dram_init_banksize(). It is platform-dependent how to detect the
memory banks. Currently, UniPhier adopts the memory banks _alleged_
by DT. This is based on the assumption that users bind a correct DT
in their build process.
Come to think of it, the DRAM controller has already been set up
before U-Boot is entered (because U-Boot runs on DRAM). So, the
DRAM controller setup register seems a more reliable source of any
information about DRAM stuff. The DRAM banks are initialized by
preliminary firmware (SPL, ARM Trusted Firmware BL2, or whatever),
so this means the source of the reliability is shifted from Device
Tree to such early-stage firmware. However, if the DRAM controller
is wrongly configured, the system will crash. If your system is
running, the DRAM setup register is very likely to provide the
correct DRAM mapping.
Decode the SG_MEMCONF register to get the available DRAM banks.
The dram_init() and dram_init_banksize() need similar decoding.
It would be nice if dram_init_banksize() could reuse the outcome
of dram_init(), but global variables are unavailable at this stage
because the .bss section is available only after the relocation.
As a result, SG_MEMCONF must be checked twice, but a new helper
uniphier_memconf_decode() will help to avoid code duplication.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This patch enables support for the smsc phy on the
stm32f746-disco board.
Signed-off-by: Michael Kurz <michi.kurz@gmail.com>
Acked-by: Vikas MANOCHA <vikas.manocha@st.com>
Series-changes 3:
- Add Acked-by tag to 'enable support for smsc phy on...'
This patch adds glue code required for enabling the designware
mac on stm32f7 devices.
Signed-off-by: Michael Kurz <michi.kurz@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch adds pin control definitions for use in device tree files
The definitions are based on the stm32f746 files from current
linux kernel "include/dt-bindings/pinctrl/stm32f746-pinfunc.h".
Signed-off-by: Michael Kurz <michi.kurz@gmail.com>
Acked-by: Vikas MANOCHA <vikas.manocha@st.com>
chiliBoard is a development board which uses chiliSOM as its base.
Hardware specification:
* chiliSOM (TI AM335x, DRAM, NAND)
* Ethernet PHY (id 0)
* USB host (usb1)
* MicroSD slot (mmc0)
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add configuration file with parameters that are very likely to be shared by
all ast2500-based boards.
Add ast2500-board.c file with the init code that is very likely to be
shared by all ast2500-based boards.
Reviewed-by: Simon Glass <sjg@chromium.org>
Clock Driver
This driver is ast2500-specific and is not compatible with earlier
versions of this chip. The differences are not that big, but they are
in somewhat random places, so making it compatible with ast2400 is not
worth the effort at the moment.
SDRAM MC driver
The driver is very ast2500-specific and is completely incompatible
with previous versions of the chip.
The memory controller is very poorly documented by Aspeed in the
datasheet, with any mention of the whole range of registers missing. The
initialization procedure has been basically taken from Aspeed SDK, where
it is implemented in assembly. Here it is rewritten in C, with very limited
understanding of what exactly it is doing.
Reviewed-by: Simon Glass <sjg@chromium.org>
In the cases of some boards, a MACH_TYPE number is used which is either
not registered upstream or worse (for functionality) is re-using the
number of a different (or reference) platform instead. Make sure we
have a comment in these cases.
Cc: Albert ARIBAUD <albert.aribaud@3adev.fr>
Cc: Walter Schweizer <swwa@users.sourceforge.net>
Cc: Stefan Roese <sr@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
This board is using MACH_TYPE values that were clearly picked during
development and not registered. Remove rather than support.
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
With the latest mach-types values we have many instances where we no
longer need to define a value and a few cases where the name (but not
value) have changed slightly.
Signed-off-by: Tom Rini <trini@konsulko.com>
This reverts commit 70b26cd057.
This is not a strict revert as it is easier to fix
board/atmark-techno/armadillo-800eva/armadillo-800eva.c to now the
correct name (same value) than to revert that change too.
Signed-off-by: Tom Rini <trini@konsulko.com>
We convert CONFIG_PARTITION_UUIDS to Kconfig first. But in order to cleanly
update all of the config files we must also update CMD_PART and CMD_GPT to also
be in Kconfig in order to avoid complex logic elsewhere to update all of the
config files.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The LS1046AQDS processor has three integrated USB 3.0 controllers
(USB1, USB2, and USB3) that allow direct connection to the USB
ports with appropriate protection circuitry and power supplies.
USB1 and USB2 ports are powered by a NX5P2190UK device, which
supplies 5v power at up to 1.2 A. The power enable and
power-fault-detect pins are connected to the LS1046A processor
via CPLD for individual port management.
Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Remove the trailing semicolon and space.
It's not necessary to have it on the last condition.
Suggested-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Breno Lima <breno.lima@nxp.com>
According to doc/README.distro:
"fdt_addr_r:
Mandatory. The location in RAM where the DTB will be loaded or copied to when
processing the fdtdir/devicetreedir or fdt/devicetree options in
extlinux.conf."
So add the fdt_addr_r environment variable.
Suggested-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Breno Lima <breno.lima@nxp.com>
USB Host scanning has been broken since v2016.05.
This is due to all the USB changes that happened between v2016.03
and v2016.05, especially:
2ef117fe4f usb: Remove 200 ms delay in usb_hub_port_connect_change()
a22a264ec3 usb: Change power-on / scanning timeout handling
So we need to increase the init delay to 2s using the usb_pgood_delay
environment variable.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
On mx6qsabreauto the parallel NOR width is 16 bits, so pass configure
CONFIG_SYS_FLASH_CFI_WIDTH correctly so that the CFI driver does not
use 8 bits by default.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
This patch enables the MMC support for the SDHCI controller on the
Armada 7k db-88f7040 and the Armada 8k db-88f8040 board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
This patch enables the MMC support for the SDHCI controller on the
Armada 3700 db-88f3720 board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Some SDHCI drivers might need to do some special controller configuration
after the common clock set_ios() function has been called (speed / width
configuration). This patch adds a call to the newly created function
set_ios_port() when its configured in the host driver.
This will be used by the Xenon SDHCI controller driver used on the
Marvell Armada 3700 and 7k/8k ARM64 SoCs.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Rename CONFIG_IMX31_PHYCORE_EET to CONFIG_TARGET_IMX31_PHYCORE_EET and
make this a distinct config target.
Signed-off-by: Tom Rini <trini@konsulko.com>
The sdhci controller assumes that the base clock frequency is fully supported by
the peripheral and doesn't support hardware limitations. The Linux kernel
distinguishes between base clock (max_clk) of the host controller and maximum
frequency (f_max) of the card interface. Use the same differentiation and allow
the platform to constrain the peripheral interface.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
We may want to run different firmware before running U-Boot. For
example, ARM Trusted Firmware runs before U-Boot, making U-Boot
a non-secure world boot loader. In this case, the SoC might be
initialized there, which enables us to skip SPL entirely.
This commit removes "select SPL" to make it configurable. This
also enables the Multi SoC support for the UniPhier ARMv8 SoCs.
(CONFIG_ARCH_UNIPHIER_V8_MULTI) Thanks to the driver model and
Device Tree, the U-Boot proper part is now written in a generic way.
The board/SoC parameters reside in DT. The Multi SoC support
increases the memory footprint a bit, but the U-Boot proper does
not have strict memory constraint. This will mitigate the per-SoC
(sometimes per-board) defconfig burden.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Move all of the status LED feature to drivers/led/Kconfig.
The LED status definitions were moved from the board configuration
files to the defconfig files.
TBD: Move all of the definitions in the include/status_led.h to the
relevant board's defconfig files.
Tested boards: CL-SOM-AM57x, CM-T335
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
When falcon mode support was added, it was right around when SPL_OS_BOOT
was migrated to Kconfig. So first we must move the enablement to the
defconfig file. Next, it turned off EXT support rather than add the
information to allow for falcon mode from EXT. Add this information so
that the board compiles after 5d28b930f2.
Fixes: d96796ca23 ("mx6sabresd: Add Falcon mode support")
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Use the generic "distro" boot framework to enable automatic DHCP boot.
MMC and USB are not yet implemented, so this is the only boot option.
The fdt and kernel addresses are adopted from downstream; ramdisk and
scriptaddr addresses were chosen arbitrarily.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Alexander Graf <agraf@suse.de>
Some scripts are calling the same functions, so these changes consolidate
common scripts together to reduce redundancy and shrink size a bit. This
also keeps the 'bootargs' variable from growing if manually called more
than one time. This also adds NAND booting scripts based on newly consolidated
scripts.
Signed-off-by: Adam Ford <aford173@gmail.com>
In 35fc84f, bootm was refactored so plain 'bootm' and
'bootm <subcommand>' shared a common implementation.
The 'bootm ramdisk' command implementation is now part of the common
implementation but not invoke by plain 'bootm' since the original
implementation never did ramdisk relocation. Instead, ramdisk
relocation happened in image_setup_linux() which is typically called
during the OS portion of 'bootm'.
On ARM, parameters to the Linux kernel can either be passed by FDT or
ATAGS. When using FDT, image_setup_linux() is called which also triggers
ramdisk relocation. When using ATAGS, image_setup_linux() is _not_
called because it mostly does FDT setup.
Instead of calling image_setup_linux() in both FDT and ATAGS cases,
include BOOTM_STATE_RAMDISK in the requested states during a plain
'bootm' if CONFIG_SYS_BOOT_RAMDISK_HIGH is set and remove the ramdisk
relocation from image_setup_linux(). This causes ramdisk relocation to
happen on any system where CONFIG_SYS_BOOT_RAMDISK_HIGH regardless of
the OS being booted. Also remove IMAGE_ENABLE_RAMDISK_HIGH as it was
only used by the now-removed code from image_setup_linux().
Signed-off-by: Rick Altherr <raltherr@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
commit: 65f83802b7 "serial: 16550: Add getfcr accessor"
breaks u-boot commandline working with long commands
sending to the board.
Since the above patch, you have to setup the fcr register.
For board/archs which enable OF_PLATDATA, the new field
fcr in struct ns16550_platdata is not filled with a
default value ...
This leads in not setting up the uarts fifo, which ends
in problems, when you send long commands to u-boots
commandline.
Detected this issue with automated tbot tests on am335x
based shc board.
The error does not popup, if you type commands. You need
to copy&paste a long command to u-boots commandshell
(or send a long command with tbot)
Possible boards/plattforms with problems:
./arch/arm/cpu/arm926ejs/lpc32xx/devices.c
./arch/arm/mach-tegra/board.c
./board/overo/overo.c
./board/quipos/cairo/cairo.c
./board/logicpd/omap3som/omap3logic.c
./board/logicpd/zoom1/zoom1.c
./board/timll/devkit8000/devkit8000.c
./board/lg/sniper/sniper.c
./board/ti/beagle/beagle.c
./drivers/serial/serial_rockchip.c
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Tested-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add the chip power supply voltage initialization on LS1046ARDB.
Add function power_init_board(), and it will initialize the
PMIC and call the chip power initialization function.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Set up chip power supply voltage according to voltage ID.
The fuse status register provides the values from on-chip
voltage ID fuses programmed at the factory. These values
define the voltage requirements for the chip.
Main operations:
1. Set up the core voltage
2. Set up the SERDES voltage and reset SERDES lanes
3. Enable/disable DDR controller support 0.9V if needed
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch adds a simple pmic driver for the mc34vr500 pmic which
is used in conjunction with the fsl T1 and LS1 series SoC.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch binds the sys_info->freq_systembus to Platform PLL, and
implements the IPs' clock function individually.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Up to now, there are 3 kind of SoCs under Layerscape Chassis 2,
like LS1043A, LS1046A and LS1012A. But the clocks tree has a
lot of differences, for instance, the IP modules have different
dividers to derive its clock from Platform PLL. And the core
cluster PLL and platform PLL maybe have different reference
clocks, such as LS1012A. Another problem is which clock/PLL
should be described by sys_info->freq_systembus, it is confused
in Layerscape Chissis 2.
This patch is to bind the sys_info->freq_systembus to the Platform
PLL, and handle the different divider of IP modules separately
between different SoCs, and separate reference clocks of core
cluster PLL and platform PLL.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Enable UUID and GPT partition support for NXP's ARM based SoCs
i.e. LS1012A, LS1021A, LS1043A, LS1046A and LS2080A.
Also enable DOS partition for LS1012AFRDM boards.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The patch enables PCIe in ls2080a defconfigs and
removes unused PCIe related macro defines.
Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The patch enables PCIe and E1000 in ls1043a defconfigs and
removes unused PCIe related macro defines.
Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The patch enables PCIe and E1000 in ls1012a defconfigs and
removes unused PCIe related macro defines
Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The patch enables PCIe in ls1021a defconfigs and
removes unused PCIe related macro defines.
Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Once upon a time u-boot didn't support building with two usb host
controller types, these days it does. Enable XHCI in addition to the
existing EHCI support so user can plug usb devices in all available
ports regardless of the controller type.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add support for signing with the pkcs11 engine. This allows FIT images
to be signed with keys securely stored on a smartcard, hardware security
module, etc without exposing the keys.
Support for other engines can be added in the future by modifying
rsa_engine_get_pub_key() and rsa_engine_get_priv_key() to construct
correct key_id strings.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Since we're including ti_armv7_common, let's pull in DEFAULT_LINUX_BOOT_ENV
and remove unnecessary duplicative definitions. This patch also renames a
few environmental variables to match what is inside ti_armv7_common. This
should help future-proof any subsequent memory or memory location changes.
Signed-off-by: Adam Ford <aford173@gmail.com>
This was imported from Linux 4.9 and adjusted for U-Boot.
- Replace the license block with SPDX
- Drop all *_atomic variants, which make no sense for U-Boot
- Remove the sleep_us argument, which makes no sense for U-Boot
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
It is not safe to compare timer values directly.
On 32-bit systems, for example, timer_get_us() wraps around every
72 min. (2 ^ 32 / 1000000 =~ 4295 sec =~ 72 min). Depending on
the get_ticks() implementation, it may wrap more frequently.
The 72 min might be possible on the use of U-Boot.
Let's borrow time_after, time_before, and friends to solve the
wrap-around problem.
These macros were copied from include/linux/jiffies.h of Linux 4.9.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The include/common.h is a collection of unrelated declarations,
macros, etc.
It is horrible to include such a cluttered header just for some
timer functions. Split out timer functions into include/time.h.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently, mdelay() and udelay() are declared in include/common.h,
while ndelay() in include/linux/compat.h. It would be nice to
collect them into include/linux/delay.h like Linux.
While we are here, fix the ndelay() implementation; I used the
DIV_ROUND_UP() instead of (x)/1000 because it must wait *longer*
than the given period of time.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This allows us to specify a FIT configuration that will automatically
use the correct images from the FIT blob.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Before we can sync with the latest mach-types.h file from the Linux
Kernel we need to remove some instances of MACH_TYPE_xxx from our
sources. As these values have been removed from the canonical upstream
source we should not be using them either, so drop.
Cc: Tom Warren <twarren@nvidia.com>
Cc: Lucas Stach <dev@lynxeye.de>
Cc: Luka Perkov <luka@openwrt.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Thomas Weber <weber@corscience.de>
Cc: Lucile Quirion <lucile.quirion@savoirfairelinux.com>
Cc: Matthias Weisser <weisserm@arcor.de>
Cc: Suriyan Ramasami <suriyan.r@gmail.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Cc: Bo Shen <voice.shen@atmel.com>
Cc: Nick Thompson <nick.thompson@gefanuc.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Erik van Luijk <evanluijk@interact.nl>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The MACH_TYPE for IGEP0032 was never officially used and has been
removed from upstream, so we must not use it. In order to remove this
we need to rework the status LED logic.
Cc: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Dropped becuase
- driver and related configs not used any board.
- no dm conversion.
Cc: Heiko Schocher <hs@denx.de>
Cc: Sergey Kostanbaev <sergey.kostanbaev@gmail.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Enable support for loading a splash image from within a FIT image.
The image is assumed to be generated with mkimage -E flag to hold
the data external to the FIT.
Signed-off-by: Tomas Melin <tomas.melin@vaisala.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Now that at least on the firefly board we have network support, enable
PXE and DHCP boot targets by default.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
With CONFIG_ROCKCHIP_SPL_BACK_TO_BROM enabled,
the environment is inside u-boot.
So solve it by moving environment after u-boot.
Signed-off-by: Jacob Chen <jacob2.chen@rock-chips.com>
RK3288 using the dwc2 USB host controller, enable it and other usb host
funtion like storage and ether.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Added rockchip: tag:
Signed-off-by: Simon Glass <sjg@chromium.org>
Move (and rename) the following CONFIG options to Kconfig:
CONFIG_DAVINCI_MMC (renamed to CONFIG_MMC_DAVINCI)
CONFIG_OMAP_HSMMC (renamed to CONFIG_MMC_OMAP_HS)
CONFIG_MXC_MMC (renamed to CONFIG_MMC_MXC)
CONFIG_MXS_MMC (renamed to CONFIG_MMC_MXS)
CONFIG_TEGRA_MMC (renamed to CONFIG_MMC_SDHCI_TEGRA)
CONFIG_SUNXI_MMC (renamed to CONFIG_MMC_SUNXI)
They are the same option names as used in Linux.
This commit was created as follows:
[1] Rename the options with the following command:
find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \
-type f -print | xargs sed -i -e '
s/CONFIG_DAVINCI_MMC/CONFIG_MMC_DAVINCI/g
s/CONFIG_OMAP_HSMMC/CONFIG_MMC_OMAP_HS/g
s/CONFIG_MXC_MMC/CONFIG_MMC_MXC/g
s/CONFIG_MXS_MMC/CONFIG_MMC_MXS/g
s/CONFIG_TEGRA_MMC/CONFIG_MMC_SDHCI_TEGRA/g
s/CONFIG_SUNXI_MMC/CONFIG_MMC_SUNXI/g
'
[2] Commit the changes
[3] Create entries in driver/mmc/Kconfig.
(copied from Linux)
[4] Move the options with the following command
tools/moveconfig.py -y -r HEAD \
MMC_DAVINCI MMC_OMAP_HS MMC_MXC MMC_MXS MMC_SDHCI_TEGRA MMC_SUNXI
[5] Sort and align drivers/mmc/Makefile for readability
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Move (and rename) the following CONFIG options to Kconfig:
CONFIG_EXYNOS_DWMMC (renamed to CONFIG_MMC_DW_EXYNOS)
CONFIG_HIKEY_DWMMC (renamed to CONFIG_MMC_DW_K3)
CONFIG_SOCFPGA_DWMMC (renamed to CONFIG_MMC_DW_SOCFPGA)
The "HIKEY" is a board name, so it is not suitable for the MMC
controller name. I am following the name used in Linux.
This commit was generated as follows:
[1] Rename the config options with the following command:
find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \
-type f -print | xargs sed -i -e '
s/CONFIG_EXYNOS_DWMMC/CONFIG_MMC_DW_EXYNOS/g
s/CONFIG_HIKEY_DWMMC/CONFIG_MMC_DW_K3/g
s/CONFIG_SOCFPGA_DWMMC/CONFIG_MMC_DW_SOCFPGA/g
'
[2] Commit the changes
[3] Create the entries in drivers/mmc/Kconfig
(with default y for EXYNOS and SOCFPGA)
[4] Run the following:
tools/moveconfig.py -y -r HEAD MMC_DW_EXYNOS MMC_DW_K3 MMC_DW_SOCFPGA
[5] Sort and align drivers/mmc/Makefile for readability
[6] Clean-up doc/README.socfpga by hand
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>
This commit was created as follows:
[1] Rename the option with the following command:
find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \
-type f -print | xargs sed -i -e 's/CONFIG_DWMMC/CONFIG_MMC_DW/g'
[2] create the entry for MMC_DW in drivers/mmc/Kconfig
(the prompt and help were copied from Linux)
[3] run "tools/moveconfig.py -y MMC_DW"
[4] add "depends on MMC_DW" to the MMC_DW_ROCKCHIP entry
[5] Clean-up doc/README.socfpga by hand
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>
CONFIG_SOCFPGA_DWMMC_FIFO_DEPTH is defined in the socfpga_common.h,
but not referenced at all. Remove.
Also, clean-up the README.socfpga. CONFIG_MMC should not be defined
in the header since it was moved to Kconfig by commit c27269953b
("mmc: complete unfinished move of CONFIG_MMC"). I see no grep hit
for the others.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>
callback function should be moved into sdhci_ops struct.
Other controller can use these ops for controlling clock or their own
specific register.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Some SoCs can have their own card dect scheme.
Then they may use this get_cd callback function after implementing init
in their drivers.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Do the same change which was done in ZynqMP by:
"ARM64: zynqmp: Remove CONFIG_BOOTP_SERVERIP"
(sha1: a8b6a156c0)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support to save environment as a file of FAT filesystem
on to SD card. The file will be saved with name uEnv.txt.
This environment will be retrieved during boot.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Increase environment size to 32K as the current default
environment itself is greater than 4K.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
wait_for_bit() is missing reset watchdog in case watchdog
is configured.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Since usb ether gadget have support for driver model, so enable
usb ether gadget.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The SPL load address changes based on boot type in HS devices,
ISW_ENTRY_ADDR is used to set this address for AM43xx based SoCs
for similar reasons. Add this same logic for AM33xx devices.
Also make the default value for ISW_ENTRY_ADDR correct for GP
devices based on SoC, HS devices already pick the correct
value in their defconfig.
Signed-off-by: Andrew F. Davis <afd@ti.com>
These two macros are used for the same thing, the total number of DDR
controllers for a given SoC. Use SYS_NUM_DDR_CTRLS in Kconfig and
merge existing usage.
Signed-off-by: York Sun <york.sun@nxp.com>
Use option NUM_DDR_CONTROLLERS in ddr Kconfig and clean up existing
usage in ls102xa and fsl-layerscape. Remove all powerpc macros in
config header and board header files.
Signed-off-by: York Sun <york.sun@nxp.com>
Add option SYS_FSL_ERRATUM_ESDHC111, SYS_FSL_ERRATUM_ESDHC13,
SYS_FSL_ERRATUM_ESDHC135, SYS_FSL_ERRATUM_ESDHC_A001 to mmc Kconfig.
Move existing macros to related Kconfig.
Signed-off-by: York Sun <york.sun@nxp.com>
[trini: Migrate bk4r1]
Signed-off-by: Tom Rini <trini@konsulko.com>
Create driver/ddr/fsl/Kconfig and move existing options. Clean up
existing macros.
Signed-off-by: York Sun <york.sun@nxp.com>
[trini: Migrate sbc8641d, xpedite537x and MPC8536DS, run a moveconfig.py -s]
Signed-off-by: Tom Rini <trini@konsulko.com>
Use TARGET_T1024RDB from Kconfig instead.
Signed-off-by: York Sun <york.sun@nxp.com>
[trini: Get missing hunk in board/freescale/t102xrdb/ddr.c]
Signed-off-by: Tom Rini <trini@konsulko.com>
Instead of define CONFIG_SYS_FSL_SEC_COMPAT in header files for PowerPC
and ARM SoCs, move it to Kconfig under the driver.
Signed-off-by: York Sun <york.sun@nxp.com>
According to Section 11.15.4.9.2 Indirect Write Controller of K2G SoC
TRM SPRUHY8D[1], the external master is only permitted to issue 32-bit
data interface writes until the last word of an indirect transfer
otherwise indirect writes is known to fails sometimes. So, make sure
that QSPI indirect writes are 32 bit sized except for the last write. If
the txbuf is unaligned then use bounce buffer to avoid data aborts.
So, now that the driver uses bounce_buffer, enable CONFIG_BOUNCE_BUFFER
for all boards that use Cadence QSPI driver.
[1]www.ti.com/lit/ug/spruhy8d/spruhy8d.pdf
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Now that the SPL is ready to be compiled in AArch64 and the DRAM
init code is ready, enable SPL support for the A64 SoC and in the
Pine64 defconfig.
For now we keep the boot0 header in the U-Boot proper, as this allows
to still use boot0 as an SPL replacement without hurting the SPL use
case.
We disable FEL support for now by making its compilation conditional
and disabling it for ARM64, as the code isn't ready yet.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Since entry_point and load_addr are addresses, they should be
represented as longs to cover the whole address space and to avoid
warning when compiling the SPL in 64-bit.
Also adjust debug prints to add the 'l' specifier, where needed.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The UL() macro is pretty useful in sharing constants between assembly
and C files while still being able to specify a type for C.
Move the macro from an armv8 specific header into a common header file
to be able to use it by arm code (for instance) as well.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The predominantely 32-bit ARM targets try to compile the SPL in Thumb
mode to reduce code size.
The 64-bit AArch64 instruction set does not know an alternative, concise
encoding, so the Thumb build option should only be set for 32-bit
targets.
Likewise -marm machine options are only valid for ARMv7 targets.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Add FIT image booting from MMC device, during MMC bootcmd
u-boot env script look for bootscript, else fit image or else
finally look for legacy image uImage.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Enabling FIT along with Signature will make bootm to
not-understanding u-boot legacy image formats like uImage, etc.
So this patch enabling legacy image format for backward compatibility.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Enable Flattened Image Tree support for all Engicam boards.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add config options for booting Linux from NAND in UBI format.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
gpmi-nand is the proper name used in nand driver from Linux for all
imx related nand boards, so rename mtdparts name as gpmi-nand instead
of nand, this will eventually reflects all nand info to Linux from
u-boot like mtdparts.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Boot Linux with uImage instead of zImage, so update
bootz with bootm.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Increase the nand kernel partition size, for supporting
large uImage files, maximum 8MiB.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add MAC support.
Use PHY, connected to RGMII1 as a default Eth adapter,
by appropriate setting of 'cpsw_data.active_slave'.
'cpsw_phy' env variable can override this setting.
Set the MAC addresses in the U-Boot environment.
The addresses are retrieved from the on-board EEPROM or from the SOC's
MAC fuses.
Set the following PHYs RGMII clock delays:
- Enable RX delay
- Disable TX delay
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
[uri.mashiach@compulab.co.il: add RGMII clock delays]
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
Features supported :
* Serial console
* SPI Flash
* MMC/SD Card
* eMMC storage
* SATA
* PCA9555 - GPIO expander over I2C5 bus
* USB
Use spl alternate boot device feature to define fallback to
the main boot device as it is defined by hardware.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
[uri.mashiach@compulab.co.il: Adjust to v2016.11]
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
The display is done in the device tree now, and there is no need
to pass 'display' kernel parameter any longer.
Signed-off-by: Adam Ford <aford173@gmail.com>
Enable USB gadget ethernet by default to have networking capabilities.
Tested using DHCP and TFTP to transfer kernel, DT, ramdisk.
Cc: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
'fdtfile' is the preferred name for the variable that contains the
device tree blob according to the README file.
It also makes it consistent with other i.MX boards that use config_distro,
so change it accordingly.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
When we want to use Secure Boot with HAB from SPL over U-Boot.img,
we need to append the IVT to the image and leave space for the CSF.
Images generated as firmware_ivt can directly be signed using the
Freescale code signing tool. For creation of a CSF, mkimage outputs
the correct HAB Blocks for the image.
The changes to the usual firmware image class are quite small,
that is why I implemented that directly into the default_image.
Cc: sbabic@denx.de
v2-Changes: None
Signed-off-by: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Reviewed-by: George McCollister <george.mccollister@gmail.com>
Tested-by: George McCollister <george.mccollister@gmail.com>
When using HAB as secure boot mechanism on Wandboard, the chain of
trust breaks immediately after the SPL. As this is not checking
the authenticity of the loaded image before jumping to it.
The HAB status output will not be implemented in SPL as it adds
a lot of strings that are only required in debug cases. With those
it exceeds the maximum size of the available OCRAM (69 KiB).
The SPL MISC driver support must be enabled, so that the driver can use OTP fuse
to check if HAB is enabled.
Cc: sbabic@denx.de
v2-Changes: None
Signed-off-by: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Reviewed-by: George McCollister <george.mccollister@gmail.com>
Tested-by: George McCollister <george.mccollister@gmail.com>
This is a user-unconfigurable option that is selected by the
drivers that need to overwrite SDHCI IO memory accessors.
(BCM2835 SDHCI seems the only driver that needs to do so.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
While I moved the options, I also renamed them so that they are all
prefixed with MMC_SDHCI_.
This commit was created in the following steps.
[1] Rename with the following command
find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \
-type f -print | xargs sed -i -e '
s/CONFIG_MMC_SDMA/CONFIG_MMC_SDHCI_SDMA/g
s/CONFIG_BCM2835_SDHCI/CONFIG_MMC_SDHCI_BCM2835/g
s/CONFIG_KONA_SDHCI/CONFIG_MMC_SDHCI_KONA/g
s/CONFIG_MV_SDHCI/CONFIG_MMC_SDHCI_MV/g
s/CONFIG_S5P_SDHCI/CONFIG_MMC_SDHCI_S5P/g
s/CONFIG_SPEAR_SDHCI/CONFIG_MMC_SDHCI_SPEAR/g
'
[2] create the Kconfig entries in drivers/mmc/Kconfig
[3] Move the options by the following command
tools/moveconfig.py -y MMC_SDHCI_SDMA MMC_SDHCI_BCM2835 \
MMC_SDHCI_KONA MMC_SDHCI_MV MMC_SDHCI_S5P MMC_SDHCI_SPEAR
[4] Sort drivers/mmc/Makefile for readability
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Move CONFIG_SDHCI to Kconfig and rename it to CONFIG_MMC_SDHCI.
My motivation for the rename is, ultimately, to make all the MMC
options prefixed with MMC_ and SDHCI options with MMC_SDHCI_,
like Linux.
This commit was created as follows:
[1] Rename the config option with the following command:
find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \
-type f -print | xargs sed -i -e 's/CONFIG_SDHCI/CONFIG_MMC_SDHCI/g'
[2] create the entry for MMC_SDHCI in drivers/mmc/Kconfig
[3] run "tools/moveconfig.py -y MMC_SDHCI"
[4] add "depends on MMC_SDHCI" to existing SDHCI driver entries
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Commit 7a777f6d6f ("mmc: Add generic Kconfig option") created
a Kconfig entry for this option without any actual moves, then
commit 44c798799f ("sunxi: Use Kconfig CONFIG_MMC") moved
instances only for SUNXI.
We generally do not like such partial moves. This kind of work
is automated by tools/moveconfig.py, so it is pretty easy to
complete this move.
I am adding "default ARM || PPC || SANDBOX" (suggested by Tom).
This shortens the configs and will ease new board porting.
This commit was created as follows:
[1] Edit Kconfig (remove the "depends on", add the "default",
copy the prompt and help message from Linux)
[2] Run 'tools/moveconfig.py -y -s -r HEAD MMC'
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
I am not longer using my old email address
"ajay.bhargav@einfochips.com". For U-Boot development email address is
now updated to contact@8051projects.net
Signed-off-by: Ajay Bhargav <contact@8051projects.net>
armada100_spi.c and related env is zapping becuase
of "no DM conversion".
Cc: Ajay Bhargav <ajay.bhargav@einfochips.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
armada100_spi.c, related config options and related codes
are zapping becuase of "no DM conversion".
Cc: Werner Pfister <Pfister_Werner@intercontrol.de>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add two functions for use by board implementations to decode the memory
banks of the /memory node so as to populate the global data with
ram_size and board info for memory banks.
The fdtdec_setup_memory_size() function decodes the first memory bank
and sets up the gd->ram_size with the size of the memory bank. This
function should be called from the boards dram_init().
The fdtdec_setup_memory_banksize() function decode the memory banks
(up to the CONFIG_NR_DRAM_BANKS) and populates the base address and size
into the gd->bd->bi_dram array of banks. This function should be called
from the boards dram_init_banksize().
Signed-off-by: Nathan Rossi <nathan@nathanrossi.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Michal Simek <monstr@monstr.eu>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch also includes ARM64 zynqmp changes:
- Remove platform non DM initialization
- Remove hardcoded sata base address
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
All sata based drivers are bind and corresponding block
device is created. Based on this find_scsi_device() is able
to get back block device based on scsi_curr_dev pointer.
intr_scsi() is commented now but it can be replaced by calling
find_scsi_device() and scsi_scan().
scsi_dev_desc[] is commented out but common/scsi.c heavily depends on
it. That's why CONFIG_SYS_SCSI_MAX_DEVICE is hardcoded to 1 and symbol
is reassigned to a block description allocated by uclass.
There is only one block description by device now but it doesn't need to
be correct when more devices are present.
scsi_bind() ensures corresponding block device creation.
uclass post_probe (scsi_post_probe()) is doing low level init.
SCSI/SATA DM based drivers requires to have 64bit base address as
the first entry in platform data structure to setup mmio_base.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The most of ethernet drivers are using this mdio registration sequence.
strcpy(priv->bus->name, "emac");
mdio_register(priv->bus);
Where driver can be used only with one MDIO bus because only unique
name should be used.
Other drivers are using unique device name for MDIO registration to
support multiple instances.
snprintf(priv->bus->name, sizeof(bus->name), "%s", name);
With DM dev->seq is used more even in logs
(like random MAC address generation:
printf("\nWarning: %s (eth%d) using random MAC address - %pM\n",
dev->name, dev->seq, pdata->enetaddr);
)
where eth%d prefix is used.
Simplify driver code to register mdio device with dev->seq number
to simplify mdio registration and reduce code duplication across
all drivers. With DM_SEQ_ALIAS enabled dev->seq reflects alias setting.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add compatibility string for the Ingenic JZ4780 SoC, the necessary
UART enable bit into FCR and register shift. Neither are encoded
in the DTS coming from Linux, so we need to support it this way.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add function which allows fetching the default FCR register setting
from platform data for DM , while retaining old behavior for non-DM
by returning UART_FCRVAL.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add i.MX6UL dtsi support from Linux.
Here is the last commit:
"ARM: dts: add gpio-ranges property to iMX GPIO controllers"
(sha1: bb728d662bed0fe91b152550e640cb3f6caa972c)
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Move USE_ARCH_MEMCPY/MEMSET options to Kconfig.
Make it "default y" for the ARMv7 architecture and make it
depend on !ARM64 && !SPL.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Add CX9020 board based on mx53loco.
Add simplified imx53 base device tree from kernel v4.8-rc8, to reuse
serial_mxc with DTE and prepare for device tree migration of other
functions and imx53 devices.
The CX9020 differs from i.MX53 Quick Start Board by:
- use uart2 instead of uart1
- DVI-D connector instead of VGA
- no audio
- CCAT FPGA connected to emi
- enable rtc
Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
u-boot allows modifying a device tree after it is loaded into
memory. Add fdt_fixup hook in u-boot environment which can
facilitate such modifications.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
liteBoard is a development board which uses liteSOM as its base.
Hardware specification:
* liteSOM (i.MX6UL, DRAM, eMMC)
* Ethernet PHY (id 0)
* USB host (usb_otg1)
* MicroSD slot (uSDHC1)
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
UDOO Neo boards has one FEC port connected to KSZ8091, add support for it.
Tested on a UDOO Neo Full with "dhcp zImage" command.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
UDOO Neo boards has a PFUZE300 connected to I2C1 bus.
Tested on a UDOO Neo Full with "pmic PFUZE3000 dump" command.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Add pfuze3000 voltage configuration macro for SW1AB, SW3 and VLDO1/2 according
to tables 53, 57 and 62 on PF3000 datasheet.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
It's not necessary to define the console option as we use the distro config.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
It's not necessary to define the mmcautodetect as it is not used anywhere.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
It's not necessary to support USDHC3 in U-Boot as it's being used for
the WLAN.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
This adds board support for the Toradex module family Colibri iMX6.
The familiy consists of a module with i.MX6 DualLite, i.MX6 Solo, both
with a version for commercial and industrial temperature range.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
This adds board support for the Toradex module family Apalis iMX6.
The familiy consists of a module with i.MX6 Dual, i.MX6 Quad with
commercial and industrial temperature range.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
NXP/Freescale uses macro CONFIG_ARMV8_PSCI to enable their private PSCI
implementation in PPA firmware, but this macro naming too generic, so this
patch replaces it with a specic one CONFIG_FSL_PPA_ARMV8_PSCI.
And this macro CONFIG_ARMV8_PSCI will be used for a generic PSCI for ARMv8
which will be added in following patchs.
Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The configuration used to error correction was not in line with what
linux and the ROM code is using. Fix it by using the correct
configuration. Now u-boot and the SPL are able to read correctly
anything written by them.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
A size of 0x200 seems way too short for u-boot. Increase the size
to 512k.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
It is useful to name each method so that we can print out this name when
using the method. Currently this happens using a separate function. In
preparation for unifying this, add a name to each method.
The name is only available if we have libcommon support (i.e can use
printf()).
Signed-off-by: Simon Glass <sjg@chromium.org>
The settings for 2.5G SGMII are wrong, which the 2.5G case is missed in
set_if_mode(), and the serdes PCS configuration are wrong, this patch uses
the correct settings took from Linux.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The most of ethernet drivers are using this mdio registration sequence.
strcpy(priv->bus->name, "emac");
mdio_register(priv->bus);
Where driver can be used only with one MDIO bus because only unique
name should be used.
Other drivers are using unique device name for MDIO registration to
support multiple instances.
snprintf(priv->bus->name, sizeof(bus->name), "%s", name);
With DM dev->seq is used more even in logs
(like random MAC address generation:
printf("\nWarning: %s (eth%d) using random MAC address - %pM\n",
dev->name, dev->seq, pdata->enetaddr);
)
where eth%d prefix is used.
Simplify driver code to register mdio device with dev->seq number
to simplify mdio registration and reduce code duplication across
all drivers. With DM_SEQ_ALIAS enabled dev->seq reflects alias setting.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
---
For example:
Board: Xilinx Zynq
Net: ZYNQ GEM: e000b000, phyaddr 7, interface rgmii-id
Warning: ethernet@e000b000 (eth0) using random MAC address -
7a:fc:90:53:6a:41
eth0: ethernet@e000b000ZYNQ GEM: e000c000, phyaddr ffffffff, interface
rgmii-id
Warning: ethernet@e000c000 (eth3) using random MAC address -
1a:ff:d7:1a:a1:b2
, eth3: ethernet@e000c000
** Bad device size - mmc 0 **
Checking if uenvcmd is set ...
Hit any key to stop autoboot: 0
Zynq> mdio list
eth0:
17 - Marvell 88E1111S <--> ethernet@e000b000
eth3:
17 - Marvell 88E1111S <--> ethernet@e000c000
Zynq>
All sata based drivers are bind and corresponding block
device is created. Based on this find_scsi_device() is able
to get back block device based on scsi_curr_dev pointer.
intr_scsi() is commented now but it can be replaced by calling
find_scsi_device() and scsi_scan().
scsi_dev_desc[] is commented out but common/scsi.c heavily depends on
it. That's why CONFIG_SYS_SCSI_MAX_DEVICE is hardcoded to 1 and symbol
is reassigned to a block description allocated by uclass.
There is only one block description by device now but it doesn't need to
be correct when more devices are present.
scsi_bind() ensures corresponding block device creation.
uclass post_probe (scsi_post_probe()) is doing low level init.
SCSI/SATA DM based drivers requires to have 64bit base address as
the first entry in platform data structure to setup mmio_base.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Series-changes: 2
- Use CONFIG_DM_SCSI instead of mix of DM_SCSI and DM_SATA
Ceva sata has never used sata commands that's why keep it in
SCSI part only.
- Separate scsi_scan() for DM_SCSI and do not change cmd/scsi.c
- Extend platdata
Series-changes: 3
- Fix scsi_scan return path
- Fix header location uclass-internal.h
- Add scsi_max_devs under !DM_SCSI
- Add new header device-internal because of device_probe()
- Redesign block device creation algorithm
- Use device_unbind in error path
- Create block device with id and lun numbers (lun was there in v2)
- Cleanup dev_num initialization in block device description
with fixing parameters in blk_create_devicef
- Create new Kconfig menu for SATA/SCSI drivers
- Extend description for DM_SCSI
- Fix Kconfig dependencies
- Fix kernel doc format in scsi_platdata
- Fix ahci_init_one - vendor variable
Series-changes: 4
- Fix Kconfig entry
- Remove SPL ifdef around SCSI uclass
- Clean ahci_print_info() ifdef logic
Add CycloneV based Terasic DE1-SoC board. The board boots
from SD/MMC. Ethernet and USB host is supported.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Marek Vasut <marex@denx.de>
- add additional function erratum_a009942_check_cpo to check if the
board needs tuning CPO calibration for optimal setting.
- move ERRATUM_A009942(with revision to check cpo_sample option) from
fsl_ddr_gen4.c to ctrl_regs.c for reuse on all DDR4/DDR3 parts.
- move ERRATUM_A008378 from fsl_ddr_gen4.c to ctrl_regs.c
- remove obsolete ERRATUM_A004934 which is replaced with ERRATUM_A009942.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
[YS: Replaced CONFIG_QEMU_E500 with CONFIG_ARCH_QEMU_E500]
Reviewed-by: York Sun <york.sun@nxp.com>
The LCDC controller on the lcdk board has high memory throughput
requirements. Even with the kernel-side tweaks to master peripheral
and peripheral bus burst priorities, the default PLL0 frquency of
300 MHz is not enough to service the LCD controller and causes
DMA FIFO underflows.
Increment the PLL0 multiplier to 37, resulting in PLL0 frequency of
456 MHz - the same value that downstream reference u-boot from Texas
Instruments uses.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
First of all U-Boot would search for a USB mass storage device
with either uEnv.txt or kernel-fit.itb and boot.
If USB mass storage device is not available or doesn't provide
these files then MMC will be tried.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This patch adds PCI support to the Marvell Armada-8K devel board.
Additionally the Intel E1000 ethernet driver is enabled so that
network support is available on this board, even without the
internal network interfaces being supported (yet).
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
This moves some of the Armada DB-88F7040 board specific files to a more
generic name: armada-8k. This is in preparation for the Armada-8k
support which will be added soon. And since both platforms share
most devices, lets also share most source files to not duplicate
the code here.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
These are the last two samsung boards that don't use DM_I2C. Move them
over, leaving #ifdefs to allow the maintainer to complete this work.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
Three boards are still not converting to use DM_I2C. They are also using
the old PMIC framework. Rather than removing them, add #ifdefs to allow
them to continue to build. This will give the maintainers a little more
time to decide whether to convert them or not.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
This board has not been converted to DM_SERIAL by the deadline.
Remove it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: David Müller <d.mueller@elsoft.ch>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This board has not been converted to DM_SERIAL by the deadline.
Remove it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: David Müller <d.mueller@elsoft.ch>
There are certain environment variables whose length is greater than
the defined IO buffer size. So, increase the IO buffer size to print the
entire variables.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The AM571x Industrial Development Kit (IDK) is a board based on TI's
AM571x SoC which has a single core 1.5GHz Cortex-A15processor. This
board is a development platform for the Industrial Market with:
- 1GB of DDR3L
- Dual 1Gbps Ethernet
- HDMI
- PRU-ICSS
- uSD
- 16GB eMMC
- CAN
- RS-485
- PCIe
- USB3.0
- Video Input Port
- Industrial IO port and expansion connector
The PRU/ICSS will be supported by 3rd party software for EtherCat,
Profibus, and other Industrial protocols.
The link to the data sheet and TRM can be found here:
http://www.ti.com/product/AM5718
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
BeagleBoard-X15 Rev B1 with SR1.1 platform have incompatible changes for HDMI
GPIO requiring new dtb support. This implies we have to properly identify
the platform now as well. Hence provide a different board name for the
Rev B1 variants.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
AM57xx evm Rev A3 with SR2.0 platform have incompatible changes for HDMI
GPIO requiring new dtb support. This implies we have to properly identify
the platform now as well. Hence provide a different board name for the
Rev A3 variations.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Palmas driver assumes it is always TPS659xx regulator on all DRA7xx based
boards to enable mmc regulator. This is not true always like in case of
DRA71x-evm. So get this information based on the board.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Delete omap4_vmmc_pbias_config from omap_hsmmc.c]
Signed-off-by: Tom Rini <trini@konsulko.com>
Currently, CMD_PXE is forcibly enabled in config_distro_defaults.h, so
that general purpose distributions can rely on it being defined. This
header is included, under conditions or not, by various archs or
famillies of archs / SoCs.
However, it is very possible that boards based on those SoCs will not
have a physical ethernet connector at all, even if the have a MAC; for
example, the Nanopi Neo AIR (sunxi H3) does not. It is also possible
that network booting is absolutely not necessary for a device.
However, it is not possible to disable the PXE command, as it is
forcibly enabled and is non-configurable.
But it turns out we already have a config option to build a distro-ready
image, in the name of DISTRO_DEFAULTS.
Move CMD_PXE out of the hard-coded config_distro_defaults.h into a
Kconfig option, that gets selected by DISTRO_DEFAULTS when it is set.
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Cc: Joe Hershberger <joe.hershberger@ni.com>
[trini: Make it select MENU, run moveconfig.py]
Signed-off-by: Tom Rini <trini@konsulko.com>
A number of platforms had been using the distro default feature before
it was moved to Kconfig but did not enable the new Kconfig option when
it was enabled. This caused a regression in terms of features and this
introduces breakage when more things move to Kconfig.
Signed-off-by: Tom Rini <trini@konsulko.com>
secure_tee_install is used to install and initialize a secure TEE OS such as
Linaro OP-TEE into the secure world. This function takes in the address
where the signed TEE image is loaded as an argument. The signed TEE image
consists of a header (struct tee_header), TEE code+data followed by the
signature generated using image signing tool from TI security development
package (SECDEV). Refer to README.ti-secure for more information.
This function uses 2 new secure APIs.
1. PPA_SERV_HAL_TEE_LOAD_MASTER - Must be called on CPU Core 0. Protected
memory for TEE must be reserved before calling this function. This API
needs arguments filled into struct ppa_tee_load_info. The TEE image is
authenticated and if there are no errors, the control passes to the TEE
entry point.
2. PPA_SERV_HAL_TEE_LOAD_SLAVE - Called on other CPU cores only after
a TEE_LOAD_MASTER call. Takes no arguments. Checks if TEE was
successfully loaded (on core 0) and transfers control to the same TEE
entry point.
The code at TEE entry point is expected perform OS initialization steps
and return back to non-secure world (U-Boot).
Signed-off-by: Harinarayan Bhatta <harinarayan@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a new image type representing Trusted Execution Environment (TEE)
image types. For example, an OP-TEE OS binary image.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
To help automate the loading of custom image types we add the ability
to define custom handlers for the loadable section types. When we find
a compatible type while loading a "loadable" image from a FIT image we
run its associated handlers to perform any additional steps needed for
loading this image.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When booting from EMMC, load the DTB and pass it to the kernel.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Improve the readability of the boot command. This will help a later
commit that adds DT support.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
NAND SPL boot was missing. Add it. The README specific to omapl138-lcdk
is also removed because its content does not apply anymore, i.e. the
generated AIS image can be flashed directly to the NAND without
using any external tool to create and bootable AIS image.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
NAND_MAX_CHIPS is not used anymore and has been replaced by
CONFIG_SYS_MAX_NAND_DEVICE. There is no need to keep the former
define.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
CONFIG_SYS_ALE_MASK is not used anywhere. It has probably been
renamed to CONFIG_SYS_NAND_MASK_ALE. Rename it and remove the former
from the config_whitelist.txt file.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
CONFIG_SYS_CLE_MASK is not used anywhere. It has probably been
renamed to CONFIG_SYS_NAND_MASK_CLE. Rename it and remove the former
from the config_whitelist.txt file.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The omapl138_lcdk header defines CONFIG_SYS_NAND_BUSWIDTH_16_BIT while
the correct name is CONFIG_SYS_NAND_BUSWIDTH_16BIT.
While renaming the only occurrence of CONFIG_SYS_NAND_BUSWIDTH_16_BIT,
let's also remove it from the config_whitelist.txt file.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The SPL is unable to load u-boot because the DDR2 is not configured.
Configure the DDR2.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Clean config headers by moving CONFIG_SYS_DA850_DDR_INIT away to a
Kconfig file.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
