The serial# environment variable needs to be
defined so it will be used by fastboot as serial
for the endpoint descriptor.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
LS1043A, LS1046A, LS1088A, LS2088A.
Switch to driver model for SATA on LS1021A and LS1043A.
Add support for LS1012AFRWY rev C board.
Enable SMMU for LS1043A.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=XRFI
-----END PGP SIGNATURE-----
Merge tag 'fsl-qoriq-for-v2018.11-rc1' of git://git.denx.de/u-boot-fsl-qoriq
Switch to driver model for eSDHC on Layerscape SoCs including LS1021A,
LS1043A, LS1046A, LS1088A, LS2088A.
Switch to driver model for SATA on LS1021A and LS1043A.
Add support for LS1012AFRWY rev C board.
Enable SMMU for LS1043A.
With DM_MMC working for both SPL and U-Boot, this patch removes
the legacy style of initializing the MMC driver.
Signed-off-by: Adam Ford <aford173@gmail.com>
With the pinctrl function enabled and the device tree setting up
the pins we want to use, this patch removes the manual pinmuxing
except for that which is not done by the device tree and minimal
pins necessary for SPL (like serial, GPMC, and MMC)
Signed-off-by: Adam Ford <aford173@gmail.com>
Call the PDA detection mechanism at boot time so we can have
the pda environment variable ready for use.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Call the PDA detection mechanism at boot time so we can have
the pda environment variable ready for use.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Call the PDA detection mechanism at boot time so we can have
the pda environment variable ready for use.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Call the PDA detection mechanism at boot time so we can have
the pda environment variable ready for use.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Call the PDA detection mechanism at boot time so we can have
the pda environment variable ready for use.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
This adds the support for PDA detection as common code for
Atmel boards.
Using the one wire interface over GPIO , an EEPROM memory is read
and compared to preprogrammed values for PDA screens TM4300, TM7000
and TM7000B.
Once the PDA is detected, an environment variable is set accordingly.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Add command to query information from and write text to on-screen
display (OSD) devices.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add device tree for T2080QDS board and enable CONFIG_OF_CONTROL
so that device tree can be compiled.
Update board README for device tree usage.
Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
Reuse the existing ICID setup code done for LS1046A smmu enablement
and add the equivalent setup for LS1043A chips.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The iommu-map property in the fsl-mc node is updated by
valid stream-ids by u-boot. This patch is to fixup this
property for LS208x and LS1088.
Signed-off-by: Nipun Gupta <nipun.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS1012AFRWY supports three board revisions.
Revision A and B board are collectively identified as revA/B,
Revision C board is identifies as revC.
Signed-off-by: Pramod Kumar <pramod.kumar_1@nxp.com>
[York S: revised commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
Modify the zynqmp_pmufw_version() routine to return PMUFW version so
that it can be reused wherever required. Get PMUFW version from PMU
only once at bootup and later just return stored value.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
On beaglebone black, it can so happen that PHY address
is not latched correctly on reset and board boots with
PHY responding to a different address than that
programmed in device-tree. For example, see this report:
https://groups.google.com/d/msg/beagleboard/9mctrG26Mc8/1FuI_i5KW10J
Workaround this by fixing up device-tree passed to kernel
by using the PHY address detected in hardware.
Beaglebone itself uses only one ethernet port and its DT
currently uses phy_id (obsoleted). But the function has
been written to handle multiple ports and phy_id as well
as phy-handle to make the function more generically useful.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable USB gadget support using DWC2 driver
Populate board_usb_init() to initialize clocks,
phy, reset and data needed for DWC2 IP.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
The Gardena Smart-Gateway boards have a MT7688 SoC with 128 MiB of RAM
and 8 MiB of flash (SPI NOR) and additional 128MiB SPI NAND storage.
This patch also includes 2 targets. One is the target that can be
programmed into the SPI NOR flash and a 2nd target "xxx-ram" is
added to support loading and booting via an already running U-Boot
version. This allows easy development and testing without the
need to flash the image each time.
Signed-off-by: Stefan Roese <sr@denx.de>
[fixed and regenerated defconfig files]
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
The LinkIt Smart 7688 modules have a MT7688 SoC with 128 MiB of RAM
and 32 MiB of flash (SPI NOR).
This patch also includes 2 targets. One is the target that can be
programmed into the SPI NOR flash and a 2nd target "xxx-ram" is
added to support loading and booting via an already running U-Boot
version. This allows easy development and testing without the
need to flash the image each time.
Signed-off-by: Stefan Roese <sr@denx.de>
[fixed and regenerated defconfig files]
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
If PCIe Mox module is connected we want to have PCIe node enabled
in U-Boot's device tree.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
The macro name CONFIG_WDT_ARMADA_3720 is called CONFIG_WDT_ARMADA_37XX
instead. Fix this so that watchdog really is enabled in board_init.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
This adds a new defconfig which pre-selects the PICO-Hobbit baseboard
allowing a completely non-interactive boot process.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
This adds a new defconfig which pre-selects the PICO-Pi baseboard
allowing a completely non-interactive boot process.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Drop the macro as it is defined in sh7723.h already.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Falcon mode allows the SPL to load and jump directly to the kernel,
without loading U-Boot proper.
Add detailed step by step on how to use Falcon mode on pico-imx6ul.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Falcon mode boots the kernel directly from SPL, without loading
the full U-Boot.
As pico-imx6ul does not have a GPIO for selecting Falcon versus normal
mode, enter in Falcon mode when the customer selects the
CONFIG_SPL_OS_BOOT option in menuconfig.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
The serverip part is provided from DHCP server with
'option root-path "192.168.3.1:/srv/tftp/rootfs";' parameter in dhcpd.conf
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The quotes around ${bootargs} were missing as we elaborate those variables
twice - once when we "setenv" the command and secondly when we "run" it.
Without quotes we have just empty string in the second call.
Moreover there is an issue with line breaks - as the original commands
got truncated.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The 'dhcp' command is more versatile as it allows working with the DHCP
server to obtain serverip, ipaddress and other network parameters.
The configuration necessary to obtain the serverip (dhcpd.conf):
option option-150 code 150 = ip-address;
and in the subnet definition:
option option-150 192.168.X.Y;
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The 'rootpath' can be provided by DHCP server. Removing this line prevents
from overwriting it.
To do that on the DHCP server side (isc-dhcp-server) modify dhcpd.conf
and add 'option root-path "192.168.X.Y:/srv/tftp/rootfs";'
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The new config skips the boot menu which asks which board is in
use. This is useful to allow direct booting of image without user
iteration.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Update the README file to take into accound the switch to SPL.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Currently only the module with 256MB of RAM is supported.
Add support for the 512MB of RAM variant as well.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
There are two versions of imx6ul pico SOMs: one with 256MB and another
one with 512MB of RAM.
Convert to SPL so that both versions can be supported. This patch
doesn't rework the clock initialization to avoid changing the behavior
in this same patch, so it will be cleaned up in future.
Currently only the 256MB is tested/supported.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
DM_I2C_COMPAT is somehow being enabled outside of Kconfig, so
this explicitly undefines it in the header file, and brackets
the I2C initialization around an #ifdef to not manually
initialize the I2C controller when the DM_I2C is enabled.
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Derald D. Woods <woods.technical@gmail.com>
With DM_MMC now available, this patch enables DM_MMC for the
omapl138_lcdk in U-Boot and keeps the older style for SPL.
Signed-off-by: Peter Howard <phoward@gme.net.au>
Signed-off-by: Adam Ford <aford173@gmail.com>
The OF_CONTROL and OF_PLATDATA are not really useful without DM.
This patch supports DM_SPL, but it requires manual references
both Serial and MMC.
Signed-off-by: Adam Ford <aford173@gmail.com>
The DA850-EVM supports booting from NAND when used with the
UI expander board. da850evm_nand will create an ais file
that can be burned to NAND and booted while storing the env in
NAND along with some partitions tables for storing kernel,
dtb and rootfs in NAND.
Signed-off-by: Adam Ford <aford173@gmail.com>
Add initial support for AM654 based EVM running on A53. Enable
4GB of DDR available on the EVM so that kernel DTB file
can be updated accordingly.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[Andreas: Added 4GB ddr support]
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
This patch enables DM_SERIAL for the pandora board. Verified that
the default kernel can still be booted with this.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Add support for loading U-Boot on the Broadcom 7260 SoC. This port
assumes Broadcom's BOLT bootloader is acting as the second stage
bootloader, and U-Boot is acting as the third stage bootloader, loaded
as an ELF program by BOLT.
Signed-off-by: Thomas Fitzsimmons <fitzsim@fitzsim.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
In int-ll64.h, we always use the following typedefs:
typedef unsigned int u32;
typedef unsigned long uintptr_t;
typedef unsigned long long u64;
This does not need to match to the compiler's <inttypes.h>.
Do not include it.
The use of PRI* makes the code super-ugly. You can simply use
"l" for printing uintptr_t, "ll" for u64, and no modifier for u32.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Update the README file to take into accound the switch to SPL.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
QEMU 3.0 introduced additional memory-mapped regions for PCI-E ECAM and
MMIO. Thus we need to add them to our MMU map or U-Boot will crash with
a Synchronous Abort during PCI-E probing when it tries to access the
unmapped ECAM memory area.
Reported-by: Jonathan Gray <jsg@jsg.id.au>
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Tested-by: Jonathan Gray <jsg@jsg.id.au>
Without this patch the Ethernet PHY on the p212 board does not get
fully configured.
When this happens Ethernet does not function.
The similar libretech-cc and khadas-vim boards have this code already.
That's why the Ethernet on these boards do work.
Signed-off-by: Jasper Kcoding <jasperkcoding@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Add an entry for mx7dsabresd_qspi_defconfig to avoid the following
warnings:
WARNING: no status info for 'mx7dsabresd_qspi'
WARNING: no maintainers for 'mx7dsabresd_qspi'
Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
This commit adds support for the Toradex Colibri iMX7D 1GB Computer
on Module. The module is very similar to the Colibri iMX7D 512MB
but uses eMMC instead of raw NAND. This patch introduces a new
board specific Kconfig symbol to select between the two flash
options.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Convert the codes and configurations to enable DM drivers in u-boot for
modules: i2c, PMIC, regulator, USB, Ethernet, SD/MMC, GPIO and QSPI
This patch does not change SPL, so it still uses non-DM driver for
UART, GPIO and SD/MMC.
Signed-off-by: Ye Li <ye.li@nxp.com>
On iMX7D SabreSD board, the QSPI has pins conflict with EPDC (default).
To use QSPI, users have to rework the board (de-populate R388-R391, R396-R399
populate R392-R395, R299, R300). So we add new DTS file and new defconfig
dedicated for QSPI.
Other changes to support the DM QSPI:
- Add QSPI node and alias spi0.
- Modify spi4 (spi-gpio) node and add alias spi5 for it to avoid req
conflict
- Add EPDC node in imx7d.dtsi and disable it in imx7d-sdb-qspi.dts to
align with kernel and also present the conflict.
- Add -u-boot.dtsi to modify compatible string of mx25l51245g@0 to
"spi-flash"
- Remove iomux settings of qspi in board codes which is not needed
for DM driver.
Signed-off-by: Ye Li <ye.li@nxp.com>
To support DM QSPI driver:
- Add -u-boot.dtsi to modify n25q256a@0 and n25q256a@1 compatible string
to "spi-flash" and add "num-cs" property.
- Enable DM SPI and DM SPI FLASH configurations
- Remove iomux settings of qspi1 in board codes which is not needed
for DM driver.
Signed-off-by: Ye Li <ye.li@nxp.com>
To support DM QSPI driver
- Add spi0 and spi1 alias for qspi1 and qspi2.
- Add -u-boot.dtsi to modify n25q256a@0 and n25q256a@1 compatible string
to "spi-flash" and add "num-cs" property.
- Enable DM SPI/QSPI relavent configurations
- Remove iomux settings of qspi2 in board codes which is not needed
for DM driver.
- Add sf default settings. So running "sf probe" can detect the flash
Signed-off-by: Ye Li <ye.li@nxp.com>
Update the HiKey board instructions based on the latest source
available. These instructions are derived from the ATF platform doc.
While updating the instructions, some comments on ATF issue has been
removed since it is fixed in latest ATF source.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The reset is already handled by the designware driver using
information from device tree.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
When MUSB is operating in peripheral mode, probe registering
musb core using musb_register which intern return int value
for validation. so there is no scope to preserve struct musb
pointer but the same can be used in .remove musb_stop.
So fix this by return musb_register with struct musb pointer.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Purna Chandra Mandal <purna.mandal@microchip.com>
Tested-by: Chen-Yu Tsai <wens@csie.org> # A33-OlinuXino
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
variables buf from board_mmc_init, and ret from misc_init_r
were unused on the functions, so remove it.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
The da850evm with its UI expander board can boot XIP boot from
NOR flash. This adds the instructions to the readme. file.
Signed-off-by: Adam Ford <aford173@gmail.com>
Currently building U-Boot as the coreboot payload requires user
to change the build configuration for a specific board during
menuconfig process. This uses the board's native device tree
to configure the hardware. For example, the device tree provides
PCI address range for the PCI host controller and U-Boot will
re-program all PCI devices' BAR to be within this range. In order
to make sure we don't mess up the hardware, we should guarantee
the range matches what coreboot programs the chipset.
But we really should make the coreboot payload support easier.
Just like EFI payload, we can create a generic coreboot payload
for all x86 boards as well. The payload is configured to include
as many generic drivers as possible. All stuff that touches low
level initialization are not allowed as such is the coreboot's
responsibility. Platform specific drivers (like gpio, spi, etc)
are not included.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Change the way MAC address fixup is done:
1. Stop using LK handed device-tree and calculate
the MAC address our own.
2. Allow overriding the generated MACS with environment variables:
"wlanaddr" and "btaddr".
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Commit 1473b12ad0 ("lib: fdtdec: Update ram_base to store ram start
adddress") brings regression on STM32F7 which can't boot.
Use fdtdec_setup_mem_size_base() to setup memory base and size.
Use fdtdec_setup_memory_banksize() to setup memory bank base and size.
Reported-by: Mark Olsson <mark@markolsson.se>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Cc: Mark Olsson <mark@markolsson.se>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
Use gd->bd->bi_dram[0].start initialized from DT instead of using
hardcoded CONFIG_SYS_SDRAM_BASE from config file.
Remove unused CONFIG_SYS_RAM_BASE and CONFIG_SYS_SDRAM_BASE defines.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Move ns_dev[] from header file to C file to avoid compiling warning
when header file is included by others.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: rewrite commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
Add infrastructure for ICID setup and device tree fixup on ARM
platforms. This include basic ICID setup for several devices.
Reviewed-by: Bharat Bhushan <bharat.bhushan@nxp.com>
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Initialize the led with the default state defined in device tree
in board_init and solve issue with test for led default state.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Initialize the led with the default state defined in device tree.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add an initial MAINTAINERS file based on author of the code.
Cc: Philippe Reynes <philippe.reynes@softathome.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This add the initial support of the broadcom reference
board bcm968380gerg with a bcm68380 SoC.
This board has 512 MB of RAM, 128 MB of flash (nand),
2 USB port, 1 UART, 4 ethernet ports and BCM43217 (wifi).
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
The only platform left for the AU1x00 SoCs was the pb1x00 platform, an
apparent clone of the dbau1x00 platform. As pb1x00 had no listed
maintainer I am assuming that it is also orphaned. Remove this platform
and then remove the unused SoC support.
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This platform has been marked as orphan since June of 2016 and should
have been removed some time ago. Do so now.
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Add command "boot_bank X" to switch the boot bank to either 1 or 2.
Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This is a series of line cards for Allied Telesis's SBx8100 chassis
switch. The CPU block is common to the SBx81GP24 and SBx81GT24 cards
cards collectively referred to as SBx81LIFXCAT in u-boot.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Move the gdsys Controlcenter DC specific build time kwbimage.cfg
generation code into the mach-mvebu/ directory to be shared by all 32bit
mvebu platforms.
Remove board specific kwbimage.cfg files, and use the generated one
instead. These files are all identical, with two exceptions. Clearfog
and Helios4 use the sdio boot device, whereas all others use spi. Update
the defconfigs for the exceptional boards to generate the same
kwbimage.cfg as before.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
Use MVEBU_SPL_BOOT_DEVICE_* to select between SPI and MMC, instead of
board specific symbols. This commit enables the boot device selection
menu to all mvebu platforms, but it is only effective on Turris Omnia
and gdsys Controlcenter DC platforms. A following commit will enable
boot selection for other platforms.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
Use generic mvebu Kconfig symbols like all other mvebu boards.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
u-boot-spl.bin and u-boot-spl-dtb.bin are identical when building the
turris_omnia_defconfig. This commit makes Turris Omnia consistent with
all other mvebu boards.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
Avnet Ultra96 is rebranded Xilinx zcu100 revC/D. Add new defconfig files
and point to origin internal board name.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This issue is reported by kconfiglib:
warning: style: quotes recommended around default value for string
symbol XILINX_MICROBLAZE0_HW_VER (defined at
board/xilinx/microblaze-generic/Kconfig:37)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This commit adjusts the autoboot.cmd file to use ${mmcbootdev} instead of
hardcoded value 0.
This is necessary to allow booting this board from the SD card.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The "Beaglebone Enhanced" by Sancloud is based on the Beaglebone Black,
but with the following differences:
* Gigabit capable PHY
* Extra USB hub, optional i2c control
* lps3331ap barometer connected over i2c
* MPU6050 6 axis MEMS accelerometer/gyro connected over i2c
* 1GiB DDR3 RAM
* RTL8723 Wifi/Bluetooth connected over USB
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Reviewed-by: Tom Rini <trini@konsulko.com>
That's a set of prety minor changes and fixes for ARC.
Among them:
* Improvement in CREG GPIO driver used on ARC dev boards
that allow us to re-use the driver for SPI's chip select
* Enable SPI-flsh on AXS10x boards which allows to update
U-Boot binary that gets loaded by boot-ROM
* Fix accommodating always utilized unaligned access by
GCC for ARC starting from 8.1.0
After talking with Albert, mark these boards as orphaned as he no longer
has one.
Cc: Albert ARIBAUD <albert-u-boot@aribaud.net>
Cc: Vagrant Cascadian <vagrant@debian.org>
Cc: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Update the MAINTAINERS file to list Otavio Salvador as the maintainer
for this board.
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Tom Rini <trini@konsulko.com>
OrangePi One Plus is Allwinner H6 based open-source SBC,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 1GB LPDDR3 RAM
- AXP805 PMIC
- 1Gbps GMAC via RTL8211
- USB 2.0 Host, OTG
- HDMI port
- 5V/2A DC power supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Pine H64 is a SBC with Allwinner H6 SoC produced by Pine64. It features
1GiB/2GiB/4GiB(3GiB usable) DRAM, two USB 2.0 ports, one USB 3.0 port
and a mPCIE slot.
Add support for it.
The device tree is from Linux next-20180720.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
The Allwinner H6 SoC has 3 MMC controllers like the ones in A64, with
the MMC2 come with the capability to do crypto by EMCE.
Add MMC support for H6. EMCE support is not added yet.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
H6 has different SRAM A2 address, so the ATF load address is also
different.
Add judgment code to sunxi 64-bit FIT generation script. It will judge
the SoC by the device tree's name.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Since U-Boot tools are being built anyways it's much nicer
to use them instead of relying on some of them bein installed
on build host (which might easily not be the case).
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
AXS10x boards have preloader that reads SPI flash pages and searches
special image header to fetch and load binary.
Add tool, make target (bsp-generate) to generate
update script and u-boot binary image with header for preloader.
Also add script to default environment to apply updates.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Highlights this time:
- Many small fixes to improve spec compatibility (found by SCT)
- Almost enough to run with sandbox target
- GetTime() improvements
- Enable EFI_LOADER and HYP entry on ARMv7 with NONSEC=y
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=ePTT
-----END PGP SIGNATURE-----
Merge tag 'signed-efi-next' of git://github.com/agraf/u-boot
Patch queue for efi - 2018-07-25
Highlights this time:
- Many small fixes to improve spec compatibility (found by SCT)
- Almost enough to run with sandbox target
- GetTime() improvements
- Enable EFI_LOADER and HYP entry on ARMv7 with NONSEC=y
A new defconfig is introduced to support SPL boot from QSPI NOR
flash. This is to support falcon mode for faster booting into
Linux.
Signed-off-by: York Sun <york.sun@nxp.com>
This patch updates the copyright claim for the issues reported by
legal review.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Some times gcc may generate data that is then used within code that may
be part of an efi runtime section. That data could be jump tables,
constants or strings.
In order to make sure we catch these, we need to ensure that gcc emits
them into a section that we can relocate together with all the other
efi runtime bits. This only works if the -ffunction-sections and
-fdata-sections flags are passed and the efi runtime functions are
in a section that starts with ".text".
Up to now we had all efi runtime bits in sections that did not
interfere with the normal section naming scheme, but this forces
us to do so. Hence we need to move the efi_loader text/data/rodata
sections before the global *(.text*) catch-all section.
With this patch in place, we should hopefully have an easier time
to extend the efi runtime functionality in the future.
Signed-off-by: Alexander Graf <agraf@suse.de>
[agraf: Fix x86_64 breakage]
Add 'const' (also 'static' in some places) to struct node_info
arrays to save memory footprint.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The previous e-mail pointing to Vaibhav Hiremath <hvaibhav@ti.com>
is bouncing and has for some time. This updates it to myself and I
work for Logic PD the manufacturer of the AM3517-SOM and EVM
Signed-off-by: Adam Ford <aford173@gmail.com>
The m5253evbe board has been marked as orphan since June of 2014 and
should have been dropped a while ago. Do so now.
Signed-off-by: Tom Rini <trini@konsulko.com>
Since the vast majority of i.MX6 boards are migrating to SPL,
this patch converts im6q_logic to SPL and enables the SDP for
loading SPL and u-boot.img over USB. The Falcon mode only
supports NAND flash as of now due to limited space/RAM, but
all i.MX6D/Q SOM's from Logic PD have internal NAND from which
to boot.
Signed-off-by: Adam Ford <aford173@gmail.com>
This reverts commit a637fe6f27.
The DDR DRAM calibration was enhanced by write leveling correction code.
It can be used with T-topology now.
Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.de>
Our default config already has the secure mode supported, so the
manual step is not required anymore.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
The DFU allows a more user friendly use as the details where the
bootloader is installed are abstracted.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
The addrmap5 value is the same for the 512MB and 1GB variants,
so there is no need to override it.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Falcon mode boots the kernel directly from SPL, without loading
the full U-Boot.
As pico-imx7d does not have a GPIO for selecting Falcon versus
normal mode, enter in Falcon mode when the customer selects
the CONFIG_SPL_OS_BOOT option in menuconfig.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Convert pico-imx7d to SPL support.
There are two variants of pico-imx7d SOMs:
- One with 512MB of RAM
- One with 1GB of RAM
The 512MB module contains two Hynix H5TC2G63GFR-PBA.
The 1GB module contains two Hynix H5TC4G63GFR-PBA.
The RAM size is determined in runtime by reading GPIO1_12.
While at it, also add USB Serial Download mode support as it
is very helpful for loading SPL and u-boot.img via imx_usb_loader.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
This makes sure that all Colibri iMX7 modules work with the
same timing. The changes are:
- Disable ODT on read (JEDEC standard JESD79-3F says in chapter
5.2.3 ODT during Reads: "As the DDR3 SDRAM can not terminate
and drive at the same time, RTT must be disabled at least half
a clock cycle..." and also MX7D SABRESD is disabling it)
This alone fixed memory issues for two Colibri iMX7 1GB modules
which showed issues before
- Make sure tRFC(min) is at least 260ns
- Make sure tRC is >50.625ns
- tRP needs to be >13.125ns, we can lower from 18.75ns to 15ns
- tFAW is not relevant, leave at reset
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Device trees from vanilla Linux do not specify a i.MX 7 specific
compatible string. Make sure to set partitions also when booting
upstream Linux.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Fix an invalid usage of the gpr_init function for the imx6ul
architecture
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
i.MX7 does not support BMODE due to the erratum e10574 ("Watchdog:
A watchdog timeout or software trigger will not reset the SOC"), so
remove its support.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Previously we had just made broad assumptions with which of our
boards had an eMMC or not even though this is a manufacturing time
assembly option. This takes the guessing away and actually checks for
the existence of an eMMC and sets up the has_emmc environment variable.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
The HB2 boards as well as rev 1.5 soms support eMMC
booting as well as SDHC. Add the infrastructure to support
booting these devices.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
%s/rkflashtool/rkdeveloptool/
We are using rkdeveloptool not rkflashtool.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The order distroboot searches for a boot.scr is fixed at compile time.
To make BIOS_DISABLE work as expected and boot from mmc1 instead of
mmc0 if enabled, we need to change the environment at runtime.
Especially as commit: 482cf22333 ("rockchip: rk3399-puma: add boot-on
regulator to override BIOS_DISABLE") enables the eMMC in U-Boot even
if BIOS_DISABLE is active.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Explicitly add 'python' call for 'acs_tool.pyc', to avoid failed
execution on some OSes.
Signed-off-by: Loic Devulder <ldevulder@suse.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Add support of stm32mp157c-ev1, the evaluation board with pmic stpmu1
(ev1 = mother board + daughter ed1) with device tree.
EV1 is the selected board by default in basic defconfig.
PS: CONFIG_PINCTRL_FULL activation avoid to increase
SYS_MALLOC_F_LEN (Early malloc usage: 2034)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
- add a devicetree for each variant (mmc, spi, nand)
- drop unneeded code from board and bur/common
- drop unneeded stuff from config header files
- minor adaptions to be compliant with driver model (requesting gpio,..)
- harmonize the commandset over all brppt1 targets
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
With this commit we do:
- set the bootdelay in all brppt1 defconfigs to 0, this makes
development easier, since we can break into serial console.
- move CONFIG_BOOTCOMMAND from header file to defconfig
- introduce b_mode variable for selecting the final boot-target.
This b_mode represents the boot-switch, which can found on most b&r
targets. On the brppt1 this boot-switch is derived from some gpio and
the bootcounter within the RTC block, making it so possible to force
a boot-target (as example for repair-case).
- refactor the environment for booting new flexible way
primary we want to get some bootscr.img within the mass-storage,
this script then loads everything needed for the boot.
For legacy reason we implement the t30lgcy#x boot targets, booting the
already delivered linux-images.
- make space for the cfgscr within mtdparts on brppt1_nand
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
On other OS, not one provided by B&R, it is not guaranteed that there
are factory-settings within a devicetree. So we must not treat the
absence of them as error.
Further we've the fact that on different version of the device-tree
files there are different namings of the factory-settings, we consider
this with searching for an alternative name.
changing things as following:
- don't treat as error if the bootloader version cannot written into
devicetree.
- since the naming of the factory-settings are different in different
versions of the provided device-tree we search for the alternate name
"/fset"
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
The falcon mode was never used on this board, there is also no plan to
use it. So drop this dead code.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
If a board-code calls the pmicsetup(u32 mpupll) with a mpupll value
!= 0 it wants to force some frequency with the value provided by mpupll.
Setting up 1 GHz is wrong here.
Nobody did take notice about that yet, since every board calls this
function with zero.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
This interface names may vary over different products, to consider this
fact we replace the interface label "IF1" and "IF2" on the summary
screen with some more generic wording "MAC1" and "MAC2".
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
On this linux target long time ago the OS is using DRM driver for
handling video output, the pre initialization of u-boot and the display
summary screen is obsolete. With this patch we drop the LCD-support from
thisd board.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Since we're going to drop LCD-support on brppt1 boards, we have to make
this stuff here optional and remove the #error path.
We also move out the ft_board_setup(...) from this #ifdef because
there's no relationship with the LCD-code and on the other hand this is
still needed in future even with LCD-support off.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
The linux systems running on the brppt1 targets are using modern DRM
drivers since long time ago. Further we are going to drop the LCD
support completely on this board, so the simple-framebuffer setup
becomes obsolete.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
This patch drops the lcd-screen setup, the summary screen and getting
mac-addresses based on a previous loaded device-tree for linux targets.
Selecting those linux target is simple, since we have only the brppt1.
In detail we do:
- drop the common lcd-setup code which relys on a fdt_blob
- drop the common dtb loading mechanism
- drop the now obsolete CONFIG_USE_FDT from board header and whitelist.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
This adds platform code for the FriendlyElec NanoPi K2 board based on a
Meson GXBB (S905) SoC with the Meson GXBB configuration.
This initial submission only supports:
- UART
- MMC/SDCard
- Ethernet
- Reset Controller
- Clock controller
Cc: Yuefei Tan <yftan@friendlyarm.com>
Signed-off-by: Thomas McKahan <tonymckahan@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This patch renames the routine fdtdec_setup_memory_size()
to fdtdec_setup_mem_size_base() as it now fills the
mem base as well along with size.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This patch added support of mmio read and write commands. These commands
can be used to read and write registers from the u-boot command line.
It can be useful in debugging.
Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Converting GPIO to DM requires to do changes in reset subsystem
that's why support for Microblaze soft reset via sysreset and GPIO
sysreset support was added.
These two patches enables enabling GPIO DM.
Microblaze soft reset is bind at last reset method.
GPIO reset is handled via sysreset with adding this fragment to DT.
gpio-restart {
compatible = "gpio-restart";
gpios = <&reset_gpio 0 0 0>;
/* 3rd cell ACTIVE_HIGH = 0, ACTIVE_LOW = 1 */
};
hard-reset-gpio property is not documented and also handled.
Conversion is required.
Unfortunately do_reset is required for SPL that's why use only soft
microblaze reset for now.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
We should support watchdog reset so that WATCHDOG_RESET will function
properly.
Signed-off-by: Shreenidhi Shedi <yesshedi@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
These macros are not required anymore. These will be taken from
configuration file.
Signed-off-by: Shreenidhi Shedi <yesshedi@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch changed zynqmp command to handle subcommands with
U_BOOT_CMD_MKENT.
Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The same change as was done for zynqmp with this description:
Add support for enabling the first watchdog pointed via aliases.
DT fragment:
aliases {
...
watchdog0= &watchdog0;
watchdog1 = &watchdog_lpd;
...
};
<zynqmp example removed>
Till this patch the first watchdog found in DT was used and started
which is not enabling all possible configuration based on user request.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for enabling the first watchdog pointed via aliases.
DT fragment:
aliases {
...
watchdog0 = &watchdog0;
watchdog1 = &watchdog_lpd;
...
};
dm tree fragment for above configuration with patch applied:
ZynqMP> dm tree
Class index Probed Driver Name
-----------------------------------------
...
watchdog 0 [ ] cdns_wdt | |-- watchdog@ff150000
watchdog 1 [ + ] cdns_wdt | `-- watchdog@fd4d0000
...
dm uclass fragment:
ZynqMP> dm uclass
...
uclass 75: watchdog
0 watchdog@ff150000 @ 7df02f40, seq -1, (req 1)
1 * watchdog@fd4d0000 @ 7df02ff0, seq 0, (req 0)
...
It is visible that index 1 is IP with seq 0 which means that FPD
watchdog (@fd4d0000) is in DT below LPD watchdog (@ff150000).
Till this patch the first watchdog found in DT was used and started
which is not enabling all possible configuration based on user request.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
sysreset uclass have own do_reset function which should be used instead
of board/platform specific.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch basically adds two new commands for loadig secure
images.
1. zynq rsa adds support to load secure image which can be both
authenticated or encrypted or both authenticated and encrypted
image in xilinx bootimage(BOOT.bin) format.
2. zynq aes command adds support to decrypt and load encrypted
image back to DDR as per destination address. The image has
to be encrypted using xilinx bootgen tool and to get only the
encrypted image from tool use -split option while invoking
bootgen.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
U-Boot needs to link ps7_init_gpl.c on Zynq or psu_init_gpl.c on
ZynqMP (PS init for short). The current logic to locate this file for
both platforms is:
1. if a board-specific file exists in
board/xilinx/zynq[mp]/$(CONFIG_DEFAULT_DEVICE_TREE)/ps?_init_gpl.c
then use it
2. otherwise use board/xilinx/zynq/ps?_init_gpl.c
In the latter case the file does not exist in the U-Boot sources and
must be copied in the source tree from the outside before starting the
build. This is typical when it is generated from Xilinx tools while
developing a custom hardware. However making sure that a
board-specific file is _not_ found (and used) requires some trickery
such as removing or overwriting all PS init files (e.g.: the current
meta-xilinx yocto layer).
This generates a few problems:
* if the source tree is shared among different out-of-tree builds,
they will pollute (and potentially corrupt) each other
* the source tree cannot be read-only
* any buildsystem must add a command to copy the PS init file binary
* overwriting or deleting files in the source tree is ugly as hell
Simplify usage by allowing to pass the path to the desired PS init
file in kconfig variable XILINX_PS_INIT_FILE. It can be an absolute
path or relative to $(srctree). If the variable is set, the
user-specified file will always be used without being copied
around. If the the variable is left empty, for backward compatibility
fall back to the old behaviour.
Since the issue is the same for Zynq and ZynqMP, add one kconfig
variable in a common place and use it for both.
Also use the new kconfig help text to document all the ways to give
U-Boot the PS init file.
Build-tested with all combinations of:
- platform: zynq or zynqmp
- PS init file: from XILINX_PS_INIT_FILE (absolute, relative path,
non-existing), in-tree board-specific, in board/xilinx/zynq[mp]/
- building in-tree, in subdir, in other directory
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Nathan Rossi <nathan@nathanrossi.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for loading U-Boot on the Broadcom 7445 SoC. This port
assumes Broadcom's BOLT bootloader is acting as the second stage
bootloader, and U-Boot is acting as the third stage bootloader, loaded
as an ELF program by BOLT.
Signed-off-by: Thomas Fitzsimmons <fitzsim@fitzsim.org>
Cc: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
This commit adds uCRobotics Bubblegum-96 board support. This board is
one of the 96Boards Consumer Edition platform based on Actions Semi
S900 SoC.
Features:
- Actions Semi S900 SoC (4xCortex A53, Power VR G6230 GPU)
- 2GiB RAM
- 8GiB eMMC, uSD slot
- WiFi, Bluetooth and GPS module
- 2x Host, 1x Device USB port
- HDMI
- 20-pin low speed and 40-pin high speed expanders, 6 LED, 3 buttons
U-Boot will be loaded by ATF at EL2 execution level. Relevant driver
support will be added in further commits.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The various Aries Embedded boards have been orphaned for a year and no
one has come forward to take care of them. Remove.
Signed-off-by: Tom Rini <trini@konsulko.com>
fdt_file is looking for imx6ul-geam-kit.dtb but Linux
has imx6ul-geam.dtb, since Linux skipped -kit on file name
by below commit.
"ARM: dts: imx6ul-geam: Skip suffix -kit from dts name"
(sha1: 182de5ebce71e469cfa686fcdf08c9cbe11ece97)
So, due to this mismatch U-Boot failed to pick the
proper dtb which eventually break the Linux boot.
This patch fixed this mismatch by
- renaming dts files
- update config option to use new dtb file
- update fdt_file to new dtb file name
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
The generic efi payload currently does not enumerate the PCI bus,
which means peripherals on the PCI bus are not discovered by their
drivers. This uses board_early_init_r() to do the PCI enumeration.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Previous rename of efi-x86 target missed the MAINTAINERS update,
which caused the buildman warnings:
WARNING: no status info for 'efi-x86_app'
WARNING: no maintainers for 'efi-x86_app'
This updates the board MAINTAINERS to reflect the up-to-date info.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use the clk framework to initialize clocks from drivers that need them
instead of having hardcoded frequencies and initializations from board
code.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The soms with 4GB ddr have a rowaddr of 16 not 15, this allows
the detection mechanism to properly identify them as 4GB.
However these soms can be populated with whatever amount of
memory the customer requests therefor we need a ram stride test.
We can not use the get_ram_size() function because not all 4GB's
of DDR is addressable on a 32-bit architecture. Therefore instead
we use a memory stride of 128MB's and look for the address that
the memory wraps. This function is used for all som types to
catch most memory configurations.
This is a revised version of Rabeeh Khoury's original code.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
In order to properly detect the board the checks need to be done
in a specific order. Move these tests back into a single enum
function that will always return the proper the board it is checking.
This also adds the best test we have for detecting the rev 1.5 som,
and it simplifies the device-tree filename building.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
The get_board_rev() is not needed anymore as a generic function
for the imx53 SoC has been used instead.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This change gives the opportunity to adjust Linux command line for the
imx53 device with some legacy data.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This patch prevents from the situation where we may end up with garbage
displayed on the LCD panel.
Such situation occurs when one performs "reboot -f" in Linux and then
stop in U-boot (or observe the garbage on the screen during boot up).
To prevent from such situation - the PWM pin is configured as GPIO and set
to LOW.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Without this change the following warning shows up when building:
board/liebherr/display5/display5.c:270:3:
warning: implicit declaration of function ‘eth_env_set_enetaddr’ [-Wimplicit-function-declaration]
This commit fixes this issue.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Test case:
The fitImage gets corrupted:
truncate -c -s 3M fitImage
run tftp_mmc_fitImg
setenv boot_os y
reset
[board shall hang in SPL with
"Trying to boot from MMC1" information]
Then after X seconds WDT is causing board to reset. After N boot attempts
we enter recovery mode.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
To enter the special mode, one needs to short cut two pads with e.g. screw
driver.
After power up the SPL will execute u-boot in which proper actions will be
taken.
It is worth noting that we do not alter envs (even the BOOT_FROM variable)
and unconditionally go to recovery.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Force booting through u-boot proper when environment error encountered
(as a result of either broken SPI-NOR or erased envs).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
To avoid confusion, let's rename the efi-x86 target to efi-x86_app.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This turns on the EFI framebuffer driver support so that a graphics
console can be of additional help.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Now that we have generic EFI payload support, drop EFI-specific test
logics in BayTrail Kconfig and codes, and all BayTrail boards too.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Now that we have generic EFI payload support for all x86 boards,
drop the QEMU-specific one.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
It is possible to create a generic EFI payload for all x86 boards.
The payload is configured to include as many generic drivers as
possible. All stuff that touches low-level initialization are not
allowed as such is the EFI BIOS's responsibility. Platform specific
drivers (like gpio, spi, etc) are not included.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Orange Pi Zero Plus is an open-source single-board computer
using the Allwinner H5 SOC.
H5 Orangepi Zero Plus has
- Quad-core Cortex-A53
- 512MB DDR3
- micrSD slot
- 16MBit SPI Nor flash
- Debug TTL UART
- 1GBit/s Ethernet (RTL8211E)
- Wifi (RTL8189FTV)
- USB 2.0 Host
- USB 2.0 OTG + power supply
The device tree file is copied from the Linux kernel 4.17.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Orange Pi R1 is an open-source single-board computer using the
Allwinner H2+ SOC.
H2+ Orange Pi R1 has
- Quad-core Cortex-A7
- 256MB DDR3
- micrSD slot
- 128MBit SPI Nor flash
- Debug TTL UART
- 100MBit/s Ethernet (H2+)
- 100MBit/s Ethernet (RTL8152B)
- Wifi (RTL8189ETV)
- USB 2.0 OTG + power supply
This board is very similar to the Orange Pi Zero.
The device tree file is copied from the Linux kernel 4.17.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Fix the CPGWPR/CPGWPCR register address on V3M Eagle to unlock
access to the CPG clock control registers.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Here we just add a tool for HSDK flashable images preparation
together with extensive documentation for HSDK board.
This will help real-life users to update U-Boot on the board.
HSDK board has preloader that reads SPI flash pages and searches
for a special image header to fetch and load binary.
Add tool, make target (bsp-generate) to generate
update script and u-boot binary image with header for preloader.
Also add script to default environment to apply updates.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
calloc() can fail and return NULL. The patch is checking return value
and return in case of error.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The SPL doesn't have much room, so in order to support OF_CONTROL
in SPL, we need the extra functionality of SPL_OF_PLATDATA.
Adding these features allows us to remove a small part of code without
losing the serial port during SPL.
Signed-off-by: Adam Ford <aford173@gmail.com>
The pin used for HDMI HPD should be set to GPIO mode on DRA76, similarly
to all the other DRA7 and AM5 SoCs.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The helios4 is built on the SolidRun Armada 38x SOM.
The port os based on the ClearFog board, using information from
https://github.com/helios-4/u-boot-marvell as well as dtb input
from https://github.com/helios-4/linux-marvell
Signed-off-by: Dennis Gilmore <dennis@ausil.us>
Signed-off-by: Dennis Gilmore <dgilmore@redhat.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Added the following:
1. defconfig for LS1012AFRWY Secure boot
2. PfE Validation support
Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
FRWY-LS1012A belongs to LS1012A family with features 2 1G SGMII PFE
MAC, Micro SD, USB 3.0, DDR, QuadSPI, Audio, UART.
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
[yorks: rebase and fix SPDX tag]
[yorks: fix board/freescale/ls1012afrdm/Kconfig]
Reviewed-by: York Sun <york.sun@nxp.com>
PPA firmware and header address may vary depending upon different
boards, configure ppa firmware and header address in board specific
Kconfig.
Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com>
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
As per updated hardware documentation for
lsch3 based chips like LS2088A, 0.9v support
has been added in possible supported SoC volatges
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
After the commit 9b643e312d ("treewide: replace with error() with
pr_err()"), there are some pr_err() with no line break. Add missing
line breaks.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
Code that disables the i2c slave is now in the mvtwsi i2c driver.
Platform must enable DM_I2C to use that code. Add a comment in the code
as a reminder for the planned DM_I2C migration of Turris Omnia.
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
This updates the LEGO MINDSTORMS EV3 boot script to try loading a
uEnv.txt file and a da850-lego-ev3.dtb device tree during boot.
Signed-off-by: David Lechner <david@lechnology.com>
This disables networking related items in the config. The EV3 does not have
any networking hardware, so this is wasted space.
Signed-off-by: David Lechner <david@lechnology.com>
This moves the UART init for LEGO MINDSTORMS EV3 to board_early_init_f().
Some console messages were not being printed because the UART was not
enabled until later in the init process.
Signed-off-by: David Lechner <david@lechnology.com>
This increases the kernel image to 4M and the rootfs image to 10M.
It is getting hard to get a kernel image to fit in 3M.
Signed-off-by: David Lechner <david@lechnology.com>
The SBx81LIFKW boards connect to the internal chassis management network
via a Marvell 88e6097 L2 switch. The chassis connections are direct
serdes on ports 8 and 9 with a RGMII interface on port 10 connected to
the CPU MAC.
For debugging purposes ports 0 and 1 are also taken out to headers on
the board. Because the debug interfaces are sometimes connected to with
straight ribbon cables we need to run them at 10Mbps.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
This is a series of line cards for Allied Telesis's SBx8100 chassis
switch. The CPU block is common to the SBx81GS24a, SBx81XS6, SBx81XS16
and SBx81GT40 cards collectively referred to as SBx81LIFKW in u-boot.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This switches the clearfog boards to use DM based gpio and i2c
drivers. The io expanders are configured via their device-tree
entries.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
[baruch: add DT i2c aliases]
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Here we do a couple of minor fixes like:
- Move .ivt section to the very beginning of the image
by default which allows us to use that image put right
at reset vector (usually 0x0)
- Improve relocation fix-up which became required once
we moved .ivt and understood a problem with existing implementation
where we relied on a particular placement of sections.
Now we don't care about placement because we just explicitly
check for .text and in case of ARCompact .ivt sections
- Re-implemnt do_reset() such that it calls reset_cpu() which
could implmented for a particular board
And hte most important part we introduce support for yet another
devboard from Synopsys - EMDK.
Synopsys DesignWare ARC EM Development Kit (ARC EMDK) is
an FPGA-based development platform from Synopsys aimed to speed-up
development of software for ARC EM cores and entire subsystems based on
ARC EM like Data Fusion, Secure and Sensor & Control subsystems.
U-Boot is supposed to be used as a primary bootloader on EMDK allowing
users to easily load and start their application from micro-SD card.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
After importing linux v4.16-rc1 commit 2c37e08464a8 ("kconfig: Warn if
choice default is not in choice"), Kconfig complains:
scripts/kconfig/conf --syncconfig Kconfig
board/eets/pdu001/Kconfig:22:warning: \
choice default symbol 'PDU001_RUN_LED_RED' \
is not contained in the choice
This looks to be caused by a typo. Fix it.
Fixes: 85ab0452fe ("arm: add support for PDU001")
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Felix Brack <fb@ltec.ch>
Tested-by: Felix Brack <fb@ltec.ch>
This is control board on Bitmain Antminer S9.
There are 3 board variables with 256MB, 512MB and 1024MB DDR.
DDR memory is automatically detected with using get_with using
get_ram_size().
Bitmain is using 16MB space for FPGA which is handled via
reserved-memory. Also U-Boot is allocating 16B for storing bootcounts.
Watchdog is started but never service in U-Boot.
SPL MMC is working. SPL NAND is not working because it is not supported
as of now.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Detect mmc alias at run time for setting up proper boot_targets sequence.
The first target has to correspond with boot mode.
The purpose of this patch is to get rid of CONFIG_ZYNQ_SDHCI0/1
parameters in full U-Boot.
Unfortunately this patch can't remove it because there is missing
mmc implementation for SPL_DM_SEQ_ALIAS.
Also xilinx_zynqmp.h only setup boot commands for mmc0 and mmc1.
It means using aliases with higher number won't work. But switching
between mmc0 and mmc1 should work properly.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Read reset reason reg and show it in log and also save it as variable.
Clearing reset reason when it is read to show only one status
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Overriding fastboot_set_reboot_flag() in arch/arm/mach-omap2/boot-common.c
leaves it applying all boards that derive from this, not just the ones which
have support for Android bootloader flow. Move the weak function override to
the relevant board files.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Rename fb_set_reboot_flag to fastboot_set_reboot_flag so it matches
all other fastboot code in the global name space. Fix the guards around
them so that they're dependent on FASTBOOT, not just USB_FUNCTION_FASTBOOT.
Move the weak implementation of fastboot_set_reboot_flag to fb_common.c
so we can call it from non-USB fastboot code.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Separate CMD_FASTBOOT from FASTBOOT and move code and configuration to
drivers/fastboot.
Switch dependencies on FASTBOOT to USB_FUNCTION_FASTBOOT as anyone who wants
FASTBOOT before this series wants USB_FUNCTION_FASTBOOT. Split
USB_FUNCTION_FASTBOOT from FASTBOOT so they retain their existing
behaviour.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add smc_init() to get register base from dts and
deal with atfsmc020 controler initialzation job.
Write protect is enabled by default. So WP shall
be disabled when startup, then cfi flash can be
detected and erasing and writing can be executed.
Adp-ae3xx and adp-ag101p both do smc initilize job
in lowlevel_init.S and get register base fron
CONFIG_FTSMC020_BASE. They also can be moved those
codes to board stage. Remind them as todo jobs.
After that CONFIG_FTSMC020_BASE can be removed.
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Cc: Greentime Hu <green.hu@gmail.com>
Rename
nx25 as ax25
ae250 as ae350
nx25-ae250 as ax25-ae350
including filename, variable, string and definition.
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Cc: Greentime Hu <green.hu@gmail.com>
Allwinner PHY USB code is now part of generic-phy framework,
so drop existing legacy handling like arch/arm/mach-sunxi.c
and related code areas.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Allwinner PHY USB code is now part of generic-phy framework,
so use it in board_usb_cable_connected.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Add the needed information to enable the debug uart
to have printf before the serial driver probe
(so before probe for clock, pincontrol and reset drivers)
To enable the debug on uart 4 (default console):
+ CONFIG_DEBUG_UART=y
+ CONFIG_DEBUG_UART_STM32=y
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Now that PCI devices work with highmem-enabled QEMU emulation, bump up
the RAM size in the MMU tables to gain access to the full 255 GB of RAM
potential instead of the puny 3 GB.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Reviewed-by: Simon Glass <sjg@chromium.org>
There are no changes in this commit but a new organization of the code
as follow.
* cmd/ directory:
> move existing code from cmd/tpm.c in cmd/tpm-common.c
> move specific code in cmd/tpm-v1.c
> create a specific header file with generic definitions for
commands only called cmd/tpm-user-utils.h
* lib/ directory:
> move existing code from lib/tpm.c in lib/tpm-common.c
> move specific code in lib/tpm-v1.c
> create a specific header file with generic definitions for
the library itself called lib/tpm-utils.h
* include/ directory:
> move existing code from include/tpm.h in include/tpm-common.h
> move specific code in include/tpm-v1.h
Code designated as 'common' is compiled if TPM are used. Code designated
as 'specific' is compiled only if the right specification has been
selected.
All files include tpm-common.h.
Files in cmd/ include tpm-user-utils.h.
Files in lib/ include tpm-utils.h.
Depending on the specification, files may include either (not both)
tpm-v1.h or tpm-v2.h.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Fix a few more cases of tpm.h -> tpm-v1.h, some Kconfig logic]
Signed-off-by: Tom Rini <trini@konsulko.com>
MMC is not initialized in SPL, so it cannot load u-boot.img
preventing boot from MMC.
Also driver specific functions are guarded with generic
configuration options which leads to build failures when device
driver is not enabled in config. Fix that by using driver
specific defines.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Stefano Babic <sbabic@denx.de>
The V2H Blanche port was broken since some time. This patch updates
the V2H Blanche port to use modern frameworks, DM, DT probing, SPL
for the preloading and puts it on par with the M2 Porter board.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Remove harcoded XHCI lists and detect mode, speed based on DT.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Serial-changes: 2
- Remove also XHCI macros from hardware.h
- Remove additional new line in zcu106
Add DFU support for BTicino Mamoj board and update
the same steps in README.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Simone CIANNI <simone.cianni@bticino.it>
Signed-off-by: Raffaele RECALCATI <raffaele.recalcati@bticino.it>
u-boot,dm-spl property is specific to U-Boot, so move it into
*u-boot.dtsi files for relevant i.MX6UL files.
This make syncing Linux dts files straight forward.
Also update the MAINTAINERS file for dts files.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
u-boot,dm-spl property is specific to U-Boot, so move it into
*u-boot.dtsi files for relevant i.MX6QDL files.
This make syncing Linux dts files straight forward.
Also update the MAINTAINERS file for dts files.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
This replaces TARGET_GE_B{4,6,8}50V3 with common TARGET_GE_BX50V3.
The boards are identified automatically at runtime.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Configure video arguments at run-time instead of at compile-time.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
B{46}50v3s have an internal LCD that needs to be configured,
in comparison with B850v3 which has only external displays.
Use VPD instead of `CONFIG_TARGET_GE_B{4,6,8}50V3' compile-time
checks to correct initialize video based on the monitor type.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Move the VPD reading earlier in order to establish the monitor
type as soon as possible.
The configuration of the specific environment variables needs to be
done later after the environment is configured.
Signed-off-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Enable Video PLL to fix non-working display support for Bx50v3
internal displays.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Simplify process_vpd() by unifying the switch statements handling
product specific configurations.
Signed-off-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The detect_baseboard() function actually determines whether there is an
internal LCD panel or not. Rename for clarity.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
This restores support for configuring the timing mode based on the
ddr_topology. This was originally implemented in commit 90bcc3d38d
("driver/ddr: Add support for setting timing in hws_topology_map") but
was removed as part of the upstream sync.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This syncs drivers/ddr/marvell/a38x/ with the mv_ddr-armada-17.10 branch
of https://github.com/MarvellEmbeddedProcessors/mv-ddr-marvell.git.
The upstream code is incorporated omitting the ddr4 and apn806 and
folding the nested a38x directory up one level. After that a
semi-automated step is used to drop unused features with unifdef
find drivers/ddr/marvell/a38x/ -name '*.[ch]' | \
xargs unifdef -m -UMV_DDR -UMV_DDR_ATF -UCONFIG_DDR4 \
-UCONFIG_APN806 -UCONFIG_MC_STATIC \
-UCONFIG_MC_STATIC_PRINT -UCONFIG_PHY_STATIC \
-UCONFIG_64BIT
INTER_REGS_BASE is updated to be defined as SOC_REGS_PHY_BASE.
Some now empty files are removed and the ternary license is replaced
with a SPDX GPL-2.0+ identifier.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This adds basic support for the Turris Mox board from CZ.NIC, which is
currently being crowdfunded on Indiegogo.
Turris Mox is as modular router based on the Armada 3720 SOC (same as
EspressoBin).
The basic module can be extended by different modules. The device tree
binary for the kernel can be dependent on which modules are connected,
and in what order. Because of this, the board specific code creates
in U-Boot a variable called module_topology, which carries this
information.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
Correct the SPDX tag format.
Fixes: 3b52847a45 ("Merge tag 'xilinx-for-v2018.07' of git://www.denx.de/git/u-boot-microblaze")
Signed-off-by: Tom Rini <trini@konsulko.com>
microblaze:
- Align defconfig
zynq:
- Rework fpga initialization and cpuinfo handling
zynqmp:
- Add ZynqMP R5 support
- Wire and enable watchdog on zcu100-revC
- Setup MMU map for DDR at run time
- Show board info based on DT and cleanup IDENT_STRING
zynqmp tools:
- Add read partition support
- Add initial support for Xilinx bif format for boot.bin generation
mmc:
- Fix get_timer usage on 64bit cpus
- Add support for SD3.0 UHS mode
nand-zynq:
- Add support for 16bit buswidth
- Use address cycles from onfi params
scsi:
- convert ceva sata to UCLASS_AHCI
timer:
- Add Cadence TTC for ZynqMP r5
watchdog:
- Minor cadence driver cleanup
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlr1ldMACgkQykllyylKDCHioACghoJw6+NqsZXl8zGWRP38yZ5K
mvgAnihfOQq125mpKPZmcc5yt6wVwYIU
=8ji9
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2018.07' of git://www.denx.de/git/u-boot-microblaze
Xilinx changes for v2018.07
microblaze:
- Align defconfig
zynq:
- Rework fpga initialization and cpuinfo handling
zynqmp:
- Add ZynqMP R5 support
- Wire and enable watchdog on zcu100-revC
- Setup MMU map for DDR at run time
- Show board info based on DT and cleanup IDENT_STRING
zynqmp tools:
- Add read partition support
- Add initial support for Xilinx bif format for boot.bin generation
mmc:
- Fix get_timer usage on 64bit cpus
- Add support for SD3.0 UHS mode
nand-zynq:
- Add support for 16bit buswidth
- Use address cycles from onfi params
scsi:
- convert ceva sata to UCLASS_AHCI
timer:
- Add Cadence TTC for ZynqMP r5
watchdog:
- Minor cadence driver cleanup
This patch adds support of SD3.0 for ZynqMP.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Xilinx ZynqMP also contains dual Cortex R5 which can run U-Boot.
This patch is adding minimal support to get U-Boot boot.
U-Boot on R5 runs out of DDR with default configuration that's why
DDR needs to be partitioned if there is something else running on arm64.
Console is done via Cadence uart driver and the first Cadence Triple
Timer Counter is used for time.
This configuration with uart1 was tested on zcu100-revC.
U-Boot 2018.05-rc2-00021-gd058a08d907d (Apr 18 2018 - 14:11:27 +0200)
Model: Xilinx ZynqMP R5
DRAM: 512 MiB
WARNING: Caches not enabled
MMC:
In: serial@ff010000
Out: serial@ff010000
Err: serial@ff010000
Net: Net Initialization Skipped
No ethernet found.
ZynqMP r5>
There are two ways how to run this on ZynqMP.
1. Run from ZynqMP arm64
tftpb 20000000 u-boot-r5.elf
setenv autostart no && bootelf -p 20000000
cpu 4 disable && cpu 4 release 10000000 lockstep
or
cpu 4 disable && cpu 4 release 10000000 split
2. Load via jtag when directly to R5
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Call calloc for space allocation only at one location and include if/else
to sprintf. This will simplify run time device adding based on id aliases.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
This patch fills the MMU map for DDR at run time based on information read
from Device Tree or automatically detected from static configuration.
The patch is needed because for systems which has for example 1GB of memory
but MMU map is 2GB there could be spurious accesses which was seen in past
when mapping is not fitting with actual memory installed.
Signed-off-by: Nitin Jain <nitin.jain@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enable watchdog in full U-Boot.
Similar changes were done by:
"arm: zynq: Wire watchdog internals"
(sha1: e6cc3b25d7)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch enables support zc1275 revB board. It has
SD added compared to revA. The same configuration will
work for RevC boards aswell.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Now that showing silicon version is part of the CPU
info display, let's remove checkboard().
Note that the generic show_board_info() will still
show the DT 'model' property. For instance:
U-Boot 2018.05-rc2-00025-g611b3ee0159b (Apr 19 2018 - 11:23:12 +0200)
CPU: Zynq 7z045
Silicon: v1.0
Model: Zynq ZC706 Development Board
I2C: ready
Based on patches from Ariel D'Alessandro <ariel@vanguardiasur.com.ar>,
and Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
mini configuration doesn't need to show this information.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This commit moves the FPGA descriptor definition
to mach-zynq, where it makes more sense.
Based on patches from Ariel D'Alessandro <ariel@vanguardiasur.com.ar>
and Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
As part of the main conversion a few files were missed. These files had
additional whitespace after the '*' and before the SPDX tag and my
previous regex was too strict. This time I did a grep for all SPDX tags
and then filtered out anything that matched the correct styles.
Fixes: 83d290c56f ("SPDX: Convert all of our single license tags to Linux Kernel style")
Reported-by: Heinrich Schuchardt <xypron.debian@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
These fsl email addresses are no longer valid and they do not have a
correspondent nxp.com entry.
Remove all invalid fsl email addresses and mark the boards as orphan.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
timur@freescale.com is not a valid email for quite some time, so change
it to Timur's updated email.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Timur Tabi <timur@tabi.org>
This patch is necessary for providing basic bootcount checking in the case
of using "falcon" boot mode in that board.
It forces u-boot proper boot, when we exceed the number of errors.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Allow optionally bringing up the Apalis type specific 4 lane PCIe port
as well as the PCIe switch as found on the Apalis Evaluation board. In
order to avoid violating the PCIe reset timing do this by overriding the
tegra_pcie_board_port_reset() function. Note however that both the
Apalis type specific 4 lane PCIe port as well as the regular Apalis PCIe
port are also left disabled in the device tree by default.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Fix optional Apalis type specific 4 lane PCIe port 0 and Apalis PCIe
port 1 pin muxing.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
It turns out that the current PCIe reset implementation in the PCIe
board init function is not quite working reliably due to PCIe reset
timing violations. Fix this by overriding the
tegra_pcie_board_port_reset() function.
Also allow optionally bringing up the PCIe switch as found on the Apalis
Evaluation board. Note however that the Apalis PCIe port is also left
disabled in the device tree by default.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Make the ihs_mdio driver DM-compatible, while retaining the old
functionality for not-yet-converted boards.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
According to the REVB schematic, fix the USB vbus power enable pin.
Based on original work by Wenyou Yang
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
To fix the issue of write the rootfs.ubi, adjust the smc timings
configuration of the nand controller.
Based on original work by Wenyou Yang
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
When a pin is muxed to a peripheral or as a GPIO, the only
configuration that can be set is the pullup. It is too restrictive
so this patch allows to give a full configuration.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
The drive strength has to be set to medium for the NAND data lines.
With a low drive, we can get some data corruption.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Taking into account the Amlogic Family name starts with GX, including
the GXBB, GXL and GXM SoCs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have multiple licenses (in
these cases, dual license) declared in the SPDX-License-Identifier tag.
In this case we change from listing "LICENSE-A LICENSE-B" or "LICENSE-A
or LICENSE-B" or "(LICENSE-A OR LICENSE-B)" to "LICENSE-A OR LICENSE-B"
as per the Linux Kernel style document. Note that parenthesis are
allowed so when they were used before we continue to use them.
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
Banana Pi BPI-M2 Berry is a quad-core mini single board computer
built with Allwinner V40 SoC. It features
- Quad Core ARM Cortex A7 CPU V40
- 1GB of RAM .
- microSD/SATA port..
- onboard WiFi and BT
- 4 USB A 2.0 ports
- 1 USB OTG port
- 1 HDMI port
- 1 audio jack
- DC power port
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
A common voltage of 1.35V was being programmed for all am43 board
versions. EPOS-EVM Needs 1.20V for LPDDR2.
Fixes: fc69d47262 (“board: ti: AM43XX: Add ddr voltage rail configuration”)
Reported-by: James Doublesin <doublesin@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Pull the symbol from the boards and zap struct rmobile_sysinfo as they
are rather useless. The entire purpose of that whole machinery was to
print board name in the CONFIG_ARCH_RMOBILE_BOARD_STRING. Do that in a
far simpler and more contained manner.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Rename CONFIG_RMOBILE_BOARD_STRING to CONFIG_ARCH_RMOBILE_BOARD_STRING
to make things consistent, no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
freescale.com domain is no longer reachable, so switch the
maintainers' emails to nxp.com domain instead.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Exynos5422 board has s2mps11 pmic.
If CONFIG_PMIC_S2MPS11 is enabled, it can initialize PMIC and Regulators
during booting time.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
This patch adds a device tree file for the H5 version of the Libre
Computer Board ALL-H3-CC. It is the same board first introduced in
commit afe2754412 ("sunxi: Add support for Libre Computer Board
ALL-H3-CC H3 ver."), with the H3 SoC replaced with the H5 SoC, and
has 4Gb DDR3 chips instead of 2Gb ones.
The device tree utilizes the common board design file for ALL-H3-CC,
providing just the model strings and SoC specifics.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This patch adds a device tree file for the H2+ version of the Libre
Computer Board ALL-H3-CC. It is the same board first introduced in
commit afe2754412 ("sunxi: Add support for Libre Computer Board
ALL-H3-CC H3 ver."), with the H3 SoC replaced with the H2+ SoC, and
has only two 2Gb DDR3 chips instead of four.
The device tree utilizes the common board design file for ALL-H3-CC,
providing just the model strings and SoC specifics.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
If CONFIG_SPL_SERIAL_SUPPORT is not set, then the build will fail:
board/ti/am335x/built-in.o: In function `spl_start_uboot':
board/ti/am335x/board.c:247: undefined reference to `serial_tstc'
board/ti/am335x/board.c:247: undefined reference to `serial_getc'
Avoid the calls to the serial functions in that case.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
We have a large number of places where while we historically referenced
gd in the code we no longer do, as well as cases where the code added
that line "just in case" during development and never dropped it.
Signed-off-by: Tom Rini <trini@konsulko.com>
The E2 Alt port was broken since some time. This patch updates
the E2 Alt port to use modern frameworks, DM, DT probing, SPL
for the preloading and puts it on par with the M2 Porter board.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The M2-N Gose port was broken since some time. This patch updates
the M2-N Gose port to use modern frameworks, DM, DT probing, SPL
for the preloading and puts it on par with the M2 Porter board.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The H2 Lager port was broken since some time. This patch updates
the H2 Lager port to use modern frameworks, DM, DT probing, SPL
for the preloading and puts it on par with the M2 Porter board.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This patch removes warp7_secure_defconfig. A previous patch set
CONFIG_ARMV7_BOOT_SEC_DEFAULT=y on the unsecure WaRP7 config. Fabio asked
if I could confirm that the NXP and upstream kernels will boot on the WaRP7
with CONFIG_ARMV7_BOOT_SEC_DEFAULT=y. I can confirm that this is the case,
so there's no need to support the secure defconfig - drop it now.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Suggested-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
mx7dsabresd_secure_defconfig was introduced to allow booting NXP kernel
that has CAAM support and needs to boot in secure mode.
Instead of keeping two different config targets for the same board,
remove mx7dsabresd_secure_defconfig and select
CONFIG_ARMV7_BOOT_SEC_DEFAULT inside mx7dsabresd_defconfig so that
this target could be used to boot both mainline and the vendor kernel.
This makes maintenance task easier and avoid potentially confusion
for the end user.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Adding CONFIG_WARP7_ROOT_PART allows a defconfig to specify which partition
is use as the root partition on WaRP7, this is a desirable change in order
to support a different partitioning schemes. The default is the current
partition #2.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
In order to sign images with the IMX code-signing-tool (CST) we need to
know the load address of a given image. The best way to derive this load
address is to make it into a define - so that u-boot.cfg contains the
address - which we can then parse when generating the IMX CST headers.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Right now a region of 0x300000 bytes is allocated at the end of DRAM for
the purposes of loading an OPTEE firmware inside of it. This patch adds the
printout of the relevant address ranges.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Subtracts CONFIG_OPTEE_TZDRAM_SIZE from the available DRAM size.
On WaRP7 we simply define the OPTEE region as from the maximum DRAM address
minus CONFIG_OPTEE_TZDRAM_SIZE bytes.
Note the OPTEE boot process will itself subtract the DRAM region it lives
in from the memory map passed to Linux.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
This patch adds an environment variable called "hab_enabled" which gets set
to a boolean status indicating whether HAB is enabled or not.
Subsequent patches can use this environment variable to determine if its
necessary to run a given binary through the hab_auth_img console command.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
In order to correctly produce an image with a IVT/DCD header we need to
define a CSF in imximage.cfg. We just use the mx7 default here.
All we have to do with this option switched on is "make u-boot.imx" and we
then will get
- u-boot.imx
- u-boot.imx.log
The log file is really important because it gives the addresses for the HAB
that we will require to sign the u-boot image using the CST. Since the
addresses can change this logfile is a critical output.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
When static memory configuration is used U-Boot has capability to detect
memory size in setup range. Enable this feature for static
configuration.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The E2 Silk port was broken since some time. This patch updates
the E2 Silk port to use modern frameworks, DM, DT probing, SPL
for the preloading and puts it on par with the M2 Porter board.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
NOTE: The port is missing support for I2C1 for DA9063 reset, since the
I2C driver needs to be converted to DM and DT probing. That's not
an issue for this patch though, since the reset was broken on Silk
since forever.
The M2 Koelsch port was broken since some time. This patch updates
the M2 Koelsch port to use modern frameworks, DM, DT probing, SPL
for the preloading and puts it on par with the M2 Porter board.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
When U-Boot is started via JTAG, ignore the installed environment
as it may interfere with the recovery of the board.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
When U-Boot is started via JTAG, ignore the installed environment
as it may interfere with the recovery of the board.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
We only use coreboot as a target on x86 platforms, since on ARM platforms
U-Boot always runs as the primary boot loader. Rename the coreboot-x86
platform to reflect this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
These changes bring mainline back into line with the configurations
that were originally set in our stable BSP.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
By using this file one can avoid cluttering <board>.h file with u-boot
HUSH commands necessary for booting target device.
With such approach the commands are stored only in one place and can be
reused if needed.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Enable display backlight only if a message needs to be displayed.
The kernel re-initializes the backlight, which results in some
unwanted artifacts.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
u-boot has a standard "serial#" environment variable that is suitable
for storing the iSerial number we will supply via the USB device
descriptor. serial# is automatically picked up by the disk subsystem in
u-boot - thus providing a handy unique identifier in /dev/disk/by-id as
detailed below.
Storing the hardware serial identifier in serial# means we can change the
serial# if we want before USB enumeration - thus making iSerial automatic
via OTP but overridable if necessary.
This patch reads the defined OTP fuse and sets environment variable
"serial#" to the value read.
With this patch in place the USB mass storage device will appear in
/dev/disk/by-id with a unique name based on the OTP value. For example
/dev/disk/by-id/usb-Linux_UMS_disk_0_WaRP7-0xf42400d3000001d4-0:0
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Rui Miguel Silva <rui.silva@linaro.org>
Cc: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
There is currently no use for building the SPL anymore, since the
SPI loader can easily be replaced by TPL and TPL does load U-Boot
directly. Upgrade TPL to SPL and replace what used to be SPL with
it. This way we build the U-Boot sources only twice, not thrice.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The H2 Stout port was broken since some time. This patch updates
the H2 Stout port to use modern frameworks, DM, DT probing, SPL
and TPL for the preloading and puts it on par with the M2 Porter
board.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add JTAG recovery support into the M2 Porter TPL. This allows the
TPL to be loaded over JTAG, initialize the system, wait for the
JTAG debugger to load U-Boot image into RAM and then resume and
start U-Boot from RAM.
The procedure is as follows:
1) Load u-boot-tpl.bin to 0xe6300000
2) Write magic number 0x1337c0de to 0xe6300020
TPL checks for this particular magic and starts JTAG recovery
if this number is present. This is not present by default.
3) Start U-Boot TPL from 0xe6300000
4) Wait for a message from TPL on UART indicating JTAG boot:
"JTAG boot detected!"
5) Halt the system in JTAG debugger
6) Load U-Boot image (u-boot.img) to 0x4fffffc0
7) Write magic number 0xb33fc0de to 0xe6300024
TPL checks for this particular magic to verify that the U-Boot
image was loaded into DRAM by the JTAG debugger.
8) Resume the system in JTAG debugger
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add and enable TPL on M2 Porter. The TPL must fit into 16 kiB due
to the Gen2 BootROM restriction. The TPL is running from MERAM and
is capable of performing the initial initialization of PFC, Clock,
GPIO, LBSC, DBSC and QSPI NOR. DBSC is responsible for bringing up
the DDR DRAM access. The TPL is capable of loading the next stage,
U-Boot, from either SPI NOR or UART as a fallback. If either does
provide a valid U-Boot uImage, the system stops, which allows the
operator to load U-Boot ie. via JTAG and start it manually.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Pull the SPL code from porter.c into a separate file in
preparation for the addition of system initialization code.
No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add support for zc12xx boards. All of them are internal boards for
silicon validation and share very similar base platforms.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
In order that we can use eth_env_* even when CONFIG_NET isn't set, move
these functions to environment code from net code.
This fixes failures such as:
board/ti/am335x/built-in.o: In function `board_late_init':
board/ti/am335x/board.c:752: undefined reference to `eth_env_set_enetaddr'
u-boot/board/ti/am335x/board.c:766: undefined reference to `eth_env_set_enetaddr'
which caters for use cases such as:
commit f411b5cca4 ("board: am335x: Always set eth/eth1addr environment
variable")
when Ethernet is required in Linux, but not U-Boot.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
When compiling without CONFIG_CLOCK_SYNTHESIZER (which is implied by
CONFIG_DRIVER_TI_CPSW for am335x_evm), exclude the network setup for
AM335x-ICEv2 to avoid link time failures:
board/ti/am335x/board.c:683: undefined reference to `setup_clock_synthesizer'
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
AM437x QSPI boot is a single stage boot and hence needs runtime DTB
selection to support AM437x-SK and AM437x-IDK with DM enabled. This is
required to move am43xx_evm_qspiboot_defconfig to use DM/DT.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Add command GPT support
Add EMMC boot support
Add the 2 other SDMMC instances for ED1:
- SDMMC2 = mmc 1, eMMC on the ED1 board
- SDMMC3 = extension connector, deactivated by default
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Kernel stores information to the RTC_SCRATCH0 and RTC_SCRATCH1 registers
for wakeup from RTC-only mode with DDR in self-refresh. Parse these
registers during SPL boot and jump to the kernel resume vector if the
device is waking up from RTC-only modewith DDR in Self-refresh.
The RTC scratch register layout used is:
SCRATCH0 : bits00-31 : kernel resume address
SCRATCH1 : bits00-15 : RTC magic value used to detect valid config
SCRATCH1 : bits16-31 : board type information populated by bootloader
During the normal boot path the SCRATCH1 : bits16-31 are updated with
the eeprom read board type data. In the rtc_only boot path the rtc
scratchpad register is read and the board type is determined and
correspondingly ddr dpll parameters are set. This is done so as to avoid
costly i2c read to eeprom.
RTC-only +DRR in self-refresh mode support is currently only enabled for
am43xx_evm_rtconly_config.
This is not to be used with epos evm builds.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
[j-keerthy@ti.com Rebased to latest u-boot master branch]
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Texas Instruments AM3358 based low-cost board using Octavo Systems OSD3358 SIP
with built-in TPS65217 PMIC and 512MB DDR3. Board features small 35mm x
55mm size, high-speed USB OTG, microSD and 72 0.1" expansion header
pins with 2xSPI, 2xI2C, 2xUART, USB, 8xADC, up-to-44 GPIO, PRU pins and much more.
https://beagleboard.org/pocket
This was tested using the am335x_evm_usbspl_defconfig.
Note that MII pins are enabled despite not having Ethernet on this
board. This avoids an issue where otherwise many timeout errors would be
generated. See https://e2e.ti.com/support/arm/sitara_arm/f/791/t/298976
for some related discussion.
Signed-off-by: Jason Kridner <jdk@ti.com>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Latest versions of u-boot have increased in size and require more
than the 256kb allocated to it.
The MCR3000 board is equipped with an AM29LV160DB boot flash which
is organised as follows:
- One 16kb block
- Two 8kb block
- One 32kb block
- Thirty one 64kb blocks
At the time being, u-boot is a single piece occupying the 256 first
kbytes, then the environment is stored in the following 64kb block
The environment being quite tiny, we save one 64kb block by embedding
the environment in the first 8kb block, hence allowing to increase
the monitor size to 320kb.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Some config is redundant with Kconfig. Fix it.
Also remove unused configs
Move SDRAM_MAX_SIZE in the only place it is used
include/environment.h already defines CONFIG_ENV_SIZE
from CONFIG_ENV_SECT_SIZE and defines CONFIG_ENV_ADDR as
(CONFIG_SYS_FLASH_BASE + CONFIG_ENV_OFFSET)
remove BOOTARGS as bootargs is set by the different boot commands
Fix CONFIG_SYS_INIT_RAM_ADDR and CONFIG_SYS_INIT_RAM_SIZE to be in
line with CPM DPRAM organisation
Remove CONFIG_SYS_GBL_DATA_SIZE, CONFIG_SYS_GBL_DATA_OFFSET and
CONFIG_SYS_INIT_SP_OFFSET which are unused
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Since commit 17cb4b8f32 ("mtd: nand: Add+use mtd_to/from_nand and
nand_get/set_controller_data"), mtd_to_nand() has to be used instead
of mtd->priv
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
AT91 ma5d4evk board uses atmel spi driver, enable DM_SPI to
use dm functionality.
Kept few functions related to non-dm and gpio on board
files for reference and will be remove once code moved
to relevant drivers.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Enable DM_SPI for atmel SPI driver on taurus board.
Kept few functions related to non-dm and gpio on board
files for reference and will be remove once code moved
to relevant drivers.
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Highlights this time around:
- Support for new RPi3 B+ model
- Fix for some SD cards on newer RPi firmware
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=jqq6
-----END PGP SIGNATURE-----
Merge tag 'signed-rpi-next' of git://github.com/agraf/u-boot
Patch queue for rpi - 2018-04-06
Highlights this time around:
- Support for new RPi3 B+ model
- Fix for some SD cards on newer RPi firmware
In the model table for the new revision code encoding documented in
https://www.raspberrypi.org/documentation/hardware/raspberrypi/revision-codes/README.md
add the entries for old models with the new scheme and add CM3 which
only appears in the new scheme.
A device tree for CM3 is not currently upstreamed in linux. When that
happens the name will likely have to be adjusted in the table.
Signed-off-by: Jonathan Gray <jsg@jsg.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
The Raspberr Pi Foundation released a new RPi3 version which we want
to detect as well, so we can enable ethernet on it and know the correct
device tree file name.
Add an identifier for it.
Signed-off-by: Alexander Graf <agraf@suse.de>
As we are running into issues where the final U-Boot FIT image file is
exceeding our size limit, add a hint to the README.sunxi64 file
to point out the possibility of building non-debug versions of the ATF
binary. These are about 12KB smaller than the standard debug build, and
so allow successful U-Boot builds for many boards with the Allwinner H5
SoC.
Please note that under normal circumstances the debug build is still
recommended, as it gives valuable clues in case something goes wrong in
the ATF.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Code has been changed to do not use DMA anymore with the NAND
controller, instead PIO is used. Then, DMA-specific initialization may
be dropped.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Ensure the NAND controller reset line is deasserted before use.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This patch add support of hsdk platform-specific commands:
hsdk_clock set - set clock from axi_freq, cpu_freq and tun_freq
environment variables/command line arguments
hsdk_clock get - save clock frequencies to axi_freq, cpu_freq
and tun_freq environment variables
hsdk_clock print - show CPU, AXI, DDR and TUNNEL current
clock frequencies.
hsdk_clock print_all - show all currently used clock frequencies.
hsdk_init - setup board HW in one of pre-defined configuration
(hsdk_hs34 / hsdk_hs36 / hsdk_hs36_ccm / hsdk_hs38 /
hsdk_hs38_ccm / hsdk_hs38x2 / hsdk_hs38x3 / hsdk_hs38x4)
hsdk_go - run baremetal application on hsdk configured
by hsdk_init command.
This patch changes default behaviour of 'bootm' command:
now we are able to set number of CPUs to be kicked by setting
'core_mask' environment variable before 'bootm' command run.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Since the new pinctrl/gpio driver is used, so this patch removes
the old board specific pin control settings.
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Ken Ma <make@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Enable CONFIG_OF_BOAD to support delivery dtb to u-boot
at run time instead of embedded.
There are two methods to delivery dtb.
1 Pass from loader:
When u-boot boot from RAM, gdb or loader can pass dtb
via a2 to u-boot dynamically. Of course gdb or loader
shall be in charge of dtb delivery.
2 Configure CONFIG_SYS_FDT_BASE:
It can be configured as RAM or ROM base statically,
no mater u-boot boot from RAM or ROM.
If it was configured as ROM base, dtb can be burned
into ROM(spi flash) by spi driver.
Meanwhile remove CONFIG_SKIP_LOWLEVEL_INIT which is
useless in nx25-ae250 configuration.
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Cc: Greentime Hu <green.hu@gmail.com>
Remove board_mmc_init() in adp-ag101p, adp-ae3xx
and nx25-ae250 boards.
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Cc: Greentime Hu <green.hu@gmail.com>
No definition provided by input.h is used in the board file.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Alexey:
1. Significantly rework cache-related functionality.
In particular that fixes coherency problems in some corner-cases,
allows us to enable and disable caches in run-time and still
have properly running system, finally support execution from
real flash (before we used to run from DDR from the very beginning).
2. Remove string routines implemented in assembly.
That allows us to build and run U-Boot on wide range of ARC cores
with different configurations. I.e. whatever tuning is used on GCC's
command-line we'll get code for desired flavor of ARC.
Otherwise for each and every corner-case we would need to add ifdefs
in assembly code to accommodate missing instructions etc.
3. Get use of GCC's garbage collector which helps to slim-down resulting image
quite a bit.
4. Also now we may disable U-Boot self-relocation for ARC if needed either
by platform or for debugging purposes.
Refactor GO and PREP subcommands implementation for a simpler
override in the boards platform code.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Fix my fragments to list all files in the repo.
Also fix path to for Xilinx Zynq SoC (mach-zynq)
It should be the part of
"ARM: zynq: move SoC sources to mach-zynq"
(sha1: 0107f24036)
And cover dts files in board MAINTAINERS files.
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds new command "zynqmp" to handle zynqmp
specific commands like "zynqmp secure". This secure command is
used for verifying zynqmp specific secure images. The secure
image can either be authenticated or encrypted or both encrypted
and authenticated. The secure image is prepared using bootgen
and will be in xilinx specific BOOT.BIN format. The optional
key can be used for decryption of encrypted image if user
key was specified while creation BOOT.BIN.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The vcu disable bit in efuse ipdisable register is valid only
if PL powered up so, consider PL powerup status for determing
EG/EV part. If PL is not powered up, ignore EG/EV part of string.
The PL powerup status will be filled by pmufw based on PL PROGB
status in the 9th bit of version field.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Watchdog is only enabled in full u-boot. Adoption for SPL should be also
done because that's the right place where watchdog should be enabled.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch is adding support to switch to EL1 while loading an EL1
application with u-boot running at EL above EL1 in aarch64 mode.
Signed-off-by: Nitin Jain <nitinj@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch enables ethernet support for ls1012a2g5rdb.
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch enables ethernet support for ls1012ardb.
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Anjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch enables ethernet support for ls1012afrdm.
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Anjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch enables ethernet support for ls1012aqds.
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Anjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
If we check an index against array bounds, we should do so before
accessing the array and not afterwards.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
IFC-NOR and QSPI-NOR pins are multiplexed on SoC, so they cannot be
accessed simultaneously. IFC-NOR can be accessed along with SD-BOOT.
Ls1088aqds_sdcard_ifc_defconfig is default config for SD boot and
IFC-NOR to be used as flash. This allows writing to IFC-NOR flash.
QSPI and DSPI cannot be accessed in this defconfig.
IFC-NOR image is generated using ls1088aqds_defconfig.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This function is required for enabling access to early i2c function
for correct usage of QIXIS_READ and QIXIS_WRITE.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
get_board_ddr_clk(), get_board_sys_clk() and if_board_diff_clk() is
now available for SPL build.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add first support for STM32MP157C-ED1 board with "Basic" boot chain
1/ Boot Rom: load SPL with STM32 image header in SYSRAM
2/ SPL: power up and initialize the DDR and load U-Boot image
from SDCARD in DDR
3/ U-Boot: search and load extlinux.conf in SDCARD
(DISTRO activated)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Support several pixel format (8bits, 16bits, 24bits & 32bits).
Add new file st_logo_data.h which contains logo
stmicroelectronics_uboot_logo_8bit_rle.bmp.
Signed-off-by: yannick fertre <yannick.fertre@st.com>
This converts the following to Kconfig:
CONFIG_CONS_INDEX
We have existing entries for this option in a number of places, with
different guards on them. They're also sometimes used for things not
directly inside of the serial driver. First, introduce a new symbol to
guard the use of CONFIG_CONS_INDEX, so that in the case where we don't
need this for the serial driver, but for some other use, we can still do
it. Next, consolidate all of these into the single entry in
drivers/serial/Kconfig. Finally, introduce CONS_INDEX_[023456] so that
we can imply a correct value here to make the defconfig side of this
smaller.
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rework a lot of the logic here, such that I took authorship from
Adam, but kept his S-o-B line]
Signed-off-by: Tom Rini <trini@konsulko.com>
It is safe to always setup the pinmux for UART1 and UART3 to be used in
early_padconf and then if these pins are needed later on, they will be
re-muxed. This allows us to drop the usage of CONFIG_CONS_INDEX here.
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
serial# variable is needed to show the device correctly in "fastboot
devices" output. It's useful when we have several devices (in fastboot
mode) connected to single host and want to choose which one to flash.
We can't use omap_die_id_serial() for this, because AM335x lacks
DIE_ID, as can be seen from AM335x TRM. Let's do next:
- reuse board_serial variable (obtained from EEPROM in
set_board_info_env() function) to set serial#
- if board_serial is "unknown", reuse ethaddr variable to set serial#
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
BeagleBoard 'xM' does not really have NAND. CONFIG_MTDIDS_DEFAULT and
CONFIG_MTDPARTS_DEFAULT can/should be empty for 'xM'. This commit sets
the defined values if they exist.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Remove arch/arm/include/asm/arch-stm32fx/stm32_periph.h
as all defines or enums are no more used.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Use available DM stm32_timer driver instead of dedicated
mach-stm32/stm32fx/timer.c.
Remove all defines or files previously used for timer usage in
arch/arm/include/asm/arch-stm32fx and in arch/arm/mach-stm32/stm32fx
Enable DM STM32_TIMER for STM32F4/F7 and H7.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
RK3288 Vyasa has eMMC boot support, with JP4 open.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Sync rk3288-vyasa board dts from Linux for proper updates and maintenance
- rk3288-vyasa.dts: Similar to Linux dts
- rk3288-vyasa-u-boot.dtsi: u-boot dts changes
Also updated MAINTAINERS for these dts files.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
A20-SOM204 board has option with onboard 16GB eMMC. The chip is wired
to MMC2 slot.
This patch adds defconfig and dts files for this board. The dts is same
with mainline kernel.
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This is new System-On-Module platform with universal dimm socket for
easy insertation. The EVB board is designed to be universal with
future modules.
Base features of A20-SOM204 board includes:
* 1GB DDR3 RAM
* AXP209 PMU
* KSZ9031 Gigabit PHY
* AT24C16 EEPROM
* Status LED
* LCD connector
* GPIO connector
There will be variants with the following options:
* Second LAN8710A Megabit PHY
* 16MB SPI Flash memory
* eMMC card
* ATECC508 crypto device
The EVB board has:
* Debug UART
* MicroSD card connector
* USB-OTG connector
* Two USB host
* RTL8723BS WiFi/BT combo
* IrDA transceiver/receiver
* HDMI connector
* VGA connector
* Megabit ethernet transceiver
* Gigabit ethernet transceiver
* SATA connector
* CAN driver
* CSI camera
* MIC and HP connectors
* PCIe x4 connector
* USB3 connector
* Two UEXT connectors
* Two user LEDs
Some of the features are multiplexed and cannot be used the same time:
CAN and Megabit PHY. Others are not usable with A20 SoC: PCIe and USB3.
This patch adds defconfig and dts files for this board. The dts is same
with mainline kernel, except some nodes are removed to make file
compatible with existing dtsi file.
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
In README.sunxi64 we tell the user how to optionally create
u-boot-sunxi-with-spl.bin by manually running cat. Instead, have the
build system create the file automatically just like it does for 32-bit
sunxi boards.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The @gdsys.cc addresses are supposed to be used for mailing lists.
Switch all occurrences of @gdsys.de mail addresses to their @gdsys.cc
equivalent.
Also, Dirk's address was wrong in one place; fix that as well.
Signed-off-by: Mario Six <six@gdsys.cc>
Thomas reported U-Boot failed to build host tools if libfdt-devel
package is installed because tools include libfdt headers from
/usr/include/ instead of using internal ones.
This commit moves the header code:
include/libfdt.h -> include/linux/libfdt.h
include/libfdt_env.h -> include/linux/libfdt_env.h
and replaces include directives:
#include <libfdt.h> -> #include <linux/libfdt.h>
#include <libfdt_env.h> -> #include <linux/libfdt_env.h>
Reported-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Rename CONFIG_SPL_USBETH_SUPPORT to CONFIG_SPL_USB_ETHER.
This enables users to block text using CONFIG_IS_ENABLED() instead
of resorting to #if ladders with SPL and non-SPL cases.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Add R8A77965 M3N Salvator-XS development kit support. This kit is
similar to the other Salvator-X(S) ones, except is has M3N SoC on
it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add support for a new boards from devboards.de , the DBM-SoC1 .
This board has one ethernet port, one USB OTG port and USB UART.
Signed-off-by: Marek Vasut <marex@denx.de>
This seems to have been missed, possibly due to the inability to
enable TI_SECURE_DEVICE on Keystone2 devices previously.
Fixes: bfebc8c965 ("env: Rename getenv_hex(), getenv_yesno(), getenv_ulong()")
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Currently SPL_LOAD_FIT is unable to boot from nand on
i.MX6QDL platform, so enable only for MMC boards.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Engicam Is.IoT has eMMC and NAND cpu modules where MMC
is common for both, so remove explicit mmc defconfig.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
This reverts commit edf0093732 for
cm_fx6 iMX.6 Solo module as it causes frequent (around 10 percent of
power cycles) board's hangs.
These hangs happen in SPL when BSS is being initialized in SDRAM -
it appear that variables from BSS contain trash values which lead to board
hangs. Looks like that SDRAM doesn't yet finish initialization in these
cases.
Signed-off-by: Maxim Yu. Osipov <mosipov@ilbers.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Do the following to make the symbol names less confusing.
sed -i "s/\([TU][^_]\+\)_FUNCTION_DFU/DFU_OVER_\1/g" \
`git grep _FUNCTION_DFU | cut -d ":" -f 1 | sort -u`
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Lukasz Majewski <lukma@denx.de>
These ARM boards are in nice shape and still being used a lot
with e.g. QEMU, so I can maintain them.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since DRA7xx/AM57xx SR1.1 and SR1.0 has errata to limit the frequency of
MMC1 to 96MHz and frequency of MMC2 to 48MHz for AM572x SR1.1, limit the
frequency and disable higher speed modes for those revision.
Also use the recommended IO delays (those tagged with "rev11")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
To debug device tree issues involving 32- and 64-bit platforms, it is useful to
have a generic 64-bit platform available.
Add a version of the sandbox that uses 64-bit integers for its physical
addresses as well as a modified device tree.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Added CONFIG_SYS_TEXT_BASE to configs/sandbox64_defconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
The 'reset' command did not work on Porter because the reset code
was accessing the wrong PMIC address over broken I2C bus driver.
Replace the code with DM-aware code and fix up the PMIC address.
This makes the 'reset' command work again.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
