Function dtsec_configure_serdes() needs to know where the TBI PHY registers
are in order to configure SGMII for proper SerDes operation.
During SGMII initialzation, fm_eth_init_mac() passing NULL for 'phyregs'
when it called init_dtsec(), because it was believed that phyregs was not
used. In fact, it is used by dtsec_configure_serdes() to configure the TBI
PHY registers.
We also need to define the PHY registers in struct fm_mdio.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Interactive DDR debugging provides a user interface to view and modify SPD,
DIMM parameters, board options and DDR controller registers before DDR is
initialized. With this feature, developers can fine-tune DDR for board
bringup and other debugging without frequently having to reprogram the flash.
To enable this feature, define CONFIG_FSL_DDR_INTERACTIVE in board header
file and set an environment variable to activate it. Syntax:
setenv ddr_interactive on
After reset, U-boot prompts before initializing DDR controllers
FSL DDR>
The available commands are
print print SPD and intermediate computed data
reset reboot machine
recompute reload SPD and options to default and recompute regs
edit modify spd, parameter, or option
compute recompute registers from current next_step to end
next_step shows current next_step
help this message
go program the memory controller and continue with u-boot
The first command should be "compute", which reads data from DIMM SPDs and
board options, performs the calculation then stops before setting DDR
controller. A user can use "print" and "edit" commands to view and modify
anything. "Go" picks up from current step with any modification and
compltes the calculation then enables the DDR controller to continue u-boot.
"Recompute" does it over from fresh reading.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix:
usb_ohci.c: In function 'dl_transfer_length':
usb_ohci.c:768:8: warning: variable 'tdINFO' set but not used [-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
Fix:
board.c:445:8: warning: variable 'bd' set but not used [-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Now that none of the core checks CONFIG_NET_MULTI, there's not much point
in boards defining it. So scrub all references to it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This is long over due. All but two net drivers have been converted, but
those have now been dropped.
The only thing left to do is actually delete all references to NET_MULTI
and code that is compiled when that is not defined. So here we scrub the
core code.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This pushes the ugly duplicated arch ifdef lists we maintain in various
image related files out to the arch headers themselves.
Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Tested-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The current post_log_word in global data is currently split into 2x
16 bits: half for the test start, half for the test success.
Since we alredy have more than 16 POST tests defined and more could
be defined, this may result in an overflow and the post_output_backlog
would not work for the tests defined further of these 16 positions.
An additional field is added to global data so that we can now support up
to 32 (depending of architecture) tests. The post_log_word is only used
to record the start of the test and the new field post_log_res for the
test success (or failure). The post_output_backlog is for this change
also adapted.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
For post to run on ARM, 3 things are needed:
- post_log_word to be defined in gd
- a post.h include in arch/arm/lib/board.c
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Allow redirection of console output prior to console initialisation to a
temporary buffer.
To enable this functionality, the board (or arch) must define:
- CONFIG_PRE_CONSOLE_BUFFER - Enable pre-console buffer
- CONFIG_PRE_CON_BUF_ADDR - Base address of pre-console buffer
- CONFIG_PRE_CON_BUF_SZ - Size of pre-console buffer (in bytes)
The pre-console buffer will buffer the last CONFIG_PRE_CON_BUF_SZ bytes
Any earlier characters are silently dropped.
* 'master' of git://git.denx.de/u-boot-mpc85xx:
powerpc/p3060: Add SoC related support for P3060 platform
powerpc/85xx: Add support for setting up RAID engine liodns on P5020
powerpc/85xx: Refactor some defines out of corenet_ds.h
fm-eth: Add ability for board code to disable a port
powerpc/mpc8548: Add workaround for erratum NMG_LBC103
powerpc/mpc8548: Add workaround for erratum NMG_DDR120
powerpc/mpc85xxcds: Fix PCI speed
powerpc/mpc8548cds: Fix booting message
powerpc/p4080: Add support for secure boot flow
powerpc/85xx: Add Secure Boot support on P1010RDB for NOR, NAND & SPIFLASH
powerpc/85xx: Add PBL & SECUREBOOT support on P3041/P5020DS boards
powerpc/p2041rdb: remove watch dog related codes
powerpc/p2041rdb: updated description of cpld command
powerpc/p2041rdb: add more ddr frequencies support
powerpc/p2041rdb: set sysclk according to status of physical switch SW1
powerpc/p2041rdb: update cpld reset command according to CPLD 2.0
powerpc/mpc8349emds: Migrate from spd_sdram to unified DDR driver
powerpc/mpc83xx: Migrate from spd_sdram to unified DDR driver
powerpc/mpc8xxx: Add DDR2 to unified DDR driver
powerpc/mpc8xxx: Fix picos_to_mclk() and get_memory_clk_period_ps()
powerpc/mpc8xxx: Add SPD EEPROM address for single controller 2 slots
powerpc/mpc8xxx: Fix DDR code for empty first DIMM slot and enable DQS_en
powerpc/85xx: Refactor P2041RDB to use common p_corenet files
powerpc/85xx: refactor common P-Series CoreNet files for FSL boards
powerpc/85xx: Enable CMD_REGINFO on corenet boards
powerpc/85xx: p2041rdb - Remove unused 'execute' perm in TLB entries
powerpc/85xx: Fix USB protocol definitions for P1020RDB
powerpc/corenet_ds: Use separated speed tables for UDIMM and RDIMM
powerpc/mpc8xxx: Move DDR RCW overriding to common code
powerpc/mpc8xxx: Extend CWL table
powerpc/85xx: Cleanup how SVR_MAJ() is defined on MPC8536
powerpc/85xx: Cleanup extern in corenet_ds board code
powerpc/p2041rdb: Add ethernet support on P2041RDB board
powerpc/85xx: Add networking support to P1023RDS
powerpc/hydra: Add ethernet support on P5020/P3041 DS boards
powerpc/85xx: Add FMan ethernet support to P4080DS
powerpc/85xx: Add support for FMan ethernet in Independent mode
powerpc/mpc8548cds: Cleanup mpc8548cds.c
powerpc/mp: add support for discontiguous cores
powerpc/85xx: corenet_ds - Remove unused 'execute' perm in TLB entries
fdt: Add new fdt_create_phandle helper
fdt: Rename fdt_create_phandle to fdt_set_phandle
powerpc/85xx: Fix compile warnings/errors if CONFIG_SYS_DPAA_FMAN isn't set
fsl_ifc: Add the workaround for erratum IFC A-003399(enabled on P1010)
powerpc/P1010: Add workaround for erratum P1010-A003549 (related to IFC)
fsl_ifc: Add the workaround for erratum IFC-A002769 (enable on P1010)
powerpc/85xx: Expanding the window of CCSRBAR in AS=1 from 4k to 1M
powerpc/85xx: Add NAND/NAND_SPL support to P1010RDB
nand: Freescale Integrated Flash Controller NAND support
powerpc/85xx: Add basic support for P1010RDB
powerpc/85xx: Add support for new P102x/P2020 RDB style boards
powerpc/85xx: relocate CCSR before creating the initial RAM area
powerpc/85xx: introduce and document CONFIG_SYS_CCSRBAR macros
powerpc/85xx: Enable internal USB UTMI PHY on p204x/p3041/p50x0
powerpc/85xx: Add ULPI and UTMI USB Phy support for P1010/P1014
Add P3060 SoC specific information:cores setup, LIODN setup, etc
The P3060 SoC combines six e500mc Power Architecture processor cores with
high-performance datapath acceleration architecture(DPAA), CoreNet fabric
infrastructure, as well as network and peripheral interfaces.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for Job Queue/Ring LIODN for the RAID Engine on P5020. Each
Job Queue/Ring combo needs one id assigned for a total of 4 (2 JQs/2
Rings per JQ). This just handles RAID Engine in non-DPAA mode.
Signed-off-by: Santosh Shukla <santosh.shukla@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The erratum NMG_LBC103 is LBIU3 in MPC8548 errata document.
Any local bus transaction may fail during LBIU resynchronization
process when the clock divider [CLKDIV] is changing. Ensure there
is no transaction on the local bus for at least 100 microseconds
after changing clock divider LCRR[CLKDIV].
Refer to the erratum LBIU3 of mpc8548.
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Erratum NMG_DDR120 (DDR19 in MPC8548 errata document) applies to some
early version silicons. The default settings of the DDR IO receiver
biasing may not work at cold temperature. When a failure occurs,
a DDR input latches an incorrect value. The workaround will set the
receiver to an acceptable bias point.
Signed-off-by: Gong Chen
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Pre u-boot Flow:
1. User loads the u-boot image in flash
2. PBL/Configuration word is used to create LAW for Flash at 0xc0000000
(Please note that ISBC expects all these addresses, images to be
validated, entry point etc within 0 - 3.5G range)
3. ISBC validates the u-boot image, and passes control to u-boot
at 0xcffffffc.
Changes in u-boot:
1. Temporarily map CONFIG_SYS_MONITOR_BASE to the 1M
CONFIG_SYS_PBI_FLASH_WINDOW in AS=1.
(The CONFIG_SYS_PBI_FLASH_WINDOW is the address map for the flash
created by PBL/configuration word within 0 - 3.5G memory range. The
u-boot image at this address has been validated by ISBC code)
2. Remove TLB entries for 0 - 3.5G created by ISBC code
3. Remove the LAW entry for the CONFIG_SYS_PBI_FLASH_WINDOW created by
PBL/configuration word after switch to AS = 1
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Kuldip Giroh <kuldip.giroh@freescale.com>
Acked-by: Wood Scott-B07421 <B07421@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
- Remove code copying
- Reset address is setup from first stage bootloader
- Support reset vector setup on little endian
Signed-off-by: Michal Simek <monstr@monstr.eu>
Use one memory space to detect little/big endian platforms.
The first unused address(0x28) is used instead 0x0 address (reset vectors).
Detection rewrited reset vector setup from first stage bootloader.
Workflow:
1. Store 0x28 to r7
2. Do little/big endian test
3. Restore r7 to 0x28
Signed-off-by: Michal Simek <monstr@monstr.eu>
For example: Setup reset vectors if reset address is setup.
Setup user exception vector if user exception is enabled
Signed-off-by: Michal Simek <monstr@monstr.eu>
The EST SBC8260 is over 10 years old, and the SBC8240 older than
that. With the tiny amount of RAM (by today's standards), there
really isn't anyone interested in running the latest U-boot on
these EOL products anymore.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
CC: jon.diekema@smiths-aerospace.com
There are some locations in the code which anticipate printf() being called
before the console is ready by squelching printf() on gd->have_console.
Move this squelching into printf(), vprintf(), puts() and putc(). Also
make tstc() and getc() return 0 if console is not yet initialised
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
Tested-by: Simon Glass <sjg@chromium.org>
* 'post' of git://git.denx.de/u-boot-blackfin:
Blackfin: uart: implement loop callback for post
Blackfin: bf537-stamp/bf548-ezkit: update POST flash block range
Blackfin: post: generalize led/button tests with GPIOs
Blackfin: bf537-stamp: drop uart/flash post tests
Blackfin: post: drop custom test list
Blackfin: bf537-stamp: convert to gpio post hotkey
When building the zmx25 target we get:
Configuring for zmx25 board...
generic.c:108: warning: 'get_reset_cause' defined but not used
Fix this warning by defining get_reset_cause only if CONFIG_DISPLAY_CPUINFO is defined.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Jason Liu <jason.hui@linaro.org>
Acked-by: Jason Liu <jason.hui@linaro.org>
The PLL decoding algorithm didn't take into account many configuration bits.
Adjust it according to Linux kernel. Also, add PLL4 for MX53.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Jason Hui <jason.hui@linaro.org>
Tested-by: Jason Liu <Jason.hui@linaro.org>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Ben Warren <biggerbadderben@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Turn on the watchdog WDZST bit so that watchdog timer does not count during low power modes.
Prior to applying this patch mx31pdk board got watchdog resets because when it booted in the Linux prompt
and there was no activity, the system entered into idle mode while watchdog timer was still active.
Fix this by disabling watchdog timer during idle mode.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Currently the reset cause is printed like:
CPU: Freescale i.MX31 rev 2.0 at 531 MHz.Reset cause: POR
Improve readability by adding a new line like it is done on other i.MX boards.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Building without option CONFIG_DISPLAY_CPUINFO leads to
this warning:
sys_info.c:50:14: warning: 'rev_s_37xx' defined but not used
Signed-off-by: Sanjeev Premi <premi@ti.com>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Config VMMC voltage to 3V for MMC/SD card slot
and PBIAS settings needed for OMAP4
Fixes MMC/SD detection on boot from eMMC.
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
split-up spl.c into spl.c, spl_mmc.c and spl_nand.c. This avoids problems
with missing defines if a board does not use mmc or nand. This includes
adding spl_ prefix to some functions which are now public. spl_image_t is now
a public type. Added some of the common functions to omap-common.h
Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Implements the saving of boot params passed by OMAP3 ROM code.
Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Support for the new spl structure. Using the interface defined by Aneesh V for
OMAP4
Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
OMAP3 relied on the memory config done by X-loader or Configuration Header. This
has to be reworked for the implementation of a SPL. This patch configures RAM
bank 0 if CONFIG_SPL_BUILD is set. Settings for Micron-RAM used by devkit8000
are added to mem.h
Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Moves the early UART clock setup setup_clocks_for_console() from
preloader_console_init() to s_init() of OMAP4.
This is done to prepare for OMAP3 integration.
This patch was posted seperatly to the mailinglist but I decidet - since it is
a prereqesit for this patch to add it. Former port to ML:
http://article.gmane.org/gmane.comp.boot-loaders.u-boot/104395
Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The existing timing does not quite meet the minimum requirements
in the LAN9221 datasheet. The timing in this patch solves problems
noticed on some parts. The patch also combines the CS configuration
for the overo and igep0020 boards per request.
Signed-off-by: Philip Balister <philip@opensdr.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch enables ethernet support for Marvell GplugD board. Network
related commands works.
Signed-off-by: Ajay Bhargav <ajay.bhargav@einfochips.com>
This patch adds support for Fast Ethernet Controller driver for
Armada100 series.
Signed-off-by: Ajay Bhargav <ajay.bhargav@einfochips.com>
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Unified DDR driver is maintained for better performance, robustness and bug
fixes. Upgrading to use unified DDR driver for MPC83xx takes advantage of
overall improvement. It requires changes for board files to customize
platform-dependent parameters.
To utilize the unified DDR driver, a board needs to define CONFIG_FSL_DDRx
in the header file. No more boards will be accepted without such definition.
Note: the workaround for erratum DDR6 for the very old MPC834x Rev 1.0/1.1
and MPC8360 Rev 1.1/1.2 parts is not migrated to unified driver.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
DDR2 has different ODT table and values. Adding table according to Samsung
application note.
Fix additive latency calculation to avoid interger underflow.
Also converted typedef dynamic_odt_t to struct dynamic_odt.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The two slots on the same controller have different addresses.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Check second DIMM slot in case the first one is empty.
Honor DQS enable option for SDRAM mode register.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
DDR RCW varies at different speeds. It is common for all platform. Move it
out from corenet_ds.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Extend CAS write Latency (CWL) table to comply with DDR3 spec
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The MPC8536 seems to use only 3 bits for the major revision field in the
SVR rather than the 4 bits used by all other processors. The most
significant bit is used as a mfg code on MPC8536.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The P1023 has two 1G ethernet controllers the first can run in
SGMII, RGMII, or RMII. The second can only do SGMII & RGMII.
We need to setup a for SoC & board registers based on our various
configuration for ethernet to function properly on the board.
Removed CONFIG_SYS_FMAN_FW as its not used anywhere.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Lei Xu <B33228@freescale.com>
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@freescale.com>
Signed-off-by: Shaohui Xie <b21989@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Frame Manager (FMan) on QorIQ SoCs with DPAA (datapath acceleration
architecture) is the ethernet contoller block. Normally it is utilized
via Queue Manager (Qman) and Buffer Manager (Bman). However for boot
usage the FMan supports a mode similar to QE or CPM ethernet collers
called Independent mode.
Additionally the FMan block supports multiple 1g and 10g interfaces as a
single entity in the system rather than each controller being managed
uniquely. This means we have to initialize all of Fman regardless of
the number of interfaces we utilize.
Different SoCs support different combinations of the number of FMan as
well as the number of 1g & 10g interfaces support per Fman.
We add support for the following SoCs:
* P1023 - 1 Fman, 2x1g
* P4080 - 2 Fman, each Fman has 4x1g and 1x10g
* P204x/P3041/P5020 - 1 Fman, 5x1g, 1x10g
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Dai Haruki <dai.haruki@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@freescale.com>
Signed-off-by: Lei Xu <B33228@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Shaohui Xie <b21989@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some SOCs have discontiguously-numbered cores, and so we can't determine the
valid core numbers via the FRR register any more. We define
CPU_TYPE_ENTRY_MASK to specify a discontiguous core mask, and helper functions
to process the mask and enumerate over the set of valid cores.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The old fdt_create_phandle didn't actually create a phandle it just
set one. We'll introduce a new helper that actually does creation.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Gerald Van Baren <vanbaren@cideas.com>
Add ifdef protection around fman specific code related to device tree
clock setup. If we dont have CONFIG_SYS_DPAA_FMAN defined we shouldn't
be executing this code.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Issue: Address masking doesn't work properly.
When sum of the base address, defined by BA, and memory bank size,
defined by AM, exceeds 4GB (0xffff_ffff) then AMASKn[AM] doesn't mask
CSPRn[BA] bits.
Impact:
This will impact booting when we are reprogramming CSPR0(BA) and
AMASK0(AMASK) while executing from NOR Flash.
Workaround:
Re-programming of CSPR(BA) and AMASK is done while not executing from NOR
Flash. The code which programs the BA and AMASK is executed from L2-SRAM.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Issue:
Peripheral connected to IFC_CS3 may hamper booting from IFC.
Impact:
Boot from IFC may not be successful if IFC_CS3 is used.
Workaround:
If IFC_CS3 is used, gate IFC_CS3 while booting from NAND or NOR.
Also Software should select IFC_CS3 using PMUXCR[26:27] = 0x01.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Issue:
The NOR-FCM does not support access to unaligned addresses for 16 bit port size
Impact:
When 16 bit port size is used, accesses not aligned to 16 bit address boundary
will result in incorrect data
Workaround:
The workaround is to switch to GPCM mode for NOR Flash access.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
For an IFC Erratum (A-003399) we will need to access IFC registers in
cpu_init_early_f() so expand the TLB covering CCSR to 1M.
Since we need a TLB to cover 1M we move to using TLB1 array for all the
early mappings so we can cover various sizes beyond 4k.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add NAND support (including spl) on IFC, such as is found on the p1010.
Note that using hardware ECC on IFC with small-page NAND (which is what
comes on the p1010rdb reference board) means there will be insufficient
OOB space for JFFS2, since IFC does not support 1-bit ECC. UBI should
work, as it does not use OOB for anything but ECC.
When hardware ECC is not enabled in CSOR, software ECC is now used.
Signed-off-by: Dipen Dudhat <Dipen.Dudhat@freescale.com>
[scottwood@freescale.com: ECC rework and misc fixes]
Signed-off-by: Scott Wood <scottwood@freescale.com>
Before main memory (DDR) is initialized, the on-chip L1 cache is used as a
memory area for the stack and the global data (gd_t) structure. This is
called the initial RAM area, or initram. The L1 cache is locked and the TLBs
point to a non-existent address (so that there's no chance it will overlap
main memory or any device). The L1 cache is also configured not to write
out to memory or the L2 cache, so everything stays in the L1 cache.
One of the things we might do while running out of initram is relocate CCSR.
On reset, CCSR is typically located at some high 32-bit address, like
0xfe000000, and this may not be the best place for CCSR. For example, on
36-bit systems, CCSR is relocated to 0xffe000000, near the top of 36-bit
memory space.
On some future Freescale SOCs, the L1 cache will be forced to write to the
backing store, so we can no longer have the TLBs point to non-existent address.
Instead, we will point the TLBs to an unused area in CCSR. In order for this
technique to work, CCSR needs to be relocated before the initram memory is
enabled.
Unlike the original CCSR relocation code in cpu_init_early_f(), the TLBs
we create now for relocating CCSR are deleted after the relocation is finished.
cpu_init_early_f() will still need to create a TLB for CCSR (at the new
location) for normal U-Boot purposes. This is done to keep the impact to
existing U-Boot code minimal and to better isolate the CCSR relocation code.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Introduce the CONFIG_SYS_CCSRBAR_PHYS_HIGH and CONFIG_SYS_CCSRBAR_PHYS_LOW
macros, which contain the high and low portions of CONFIG_SYS_CCSRBAR_PHYS.
This is necessary for the assembly-language code that relocates CCSR, since
the assembler does not understand 64-bit constants.
CONFIG_SYS_CCSRBAR_PHYS is automatically defined from the
CONFIG_SYS_CCSRBAR_PHYS_HIGH and CONFIG_SYS_CCSRBAR_PHYS_LOW macros, so it
should not be defined in a board header file. Similarly,
CONFIG_SYS_CCSRBAR_DEFAULT is defined for each SOC in config_mpc85xx.h, so
it should also not be defined in the board header file.
CONFIG_SYS_CCSR_DO_NOT_RELOCATE is a "short-cut" macro that guarantees that
CONFIG_SYS_CCSRBAR_PHYS is set to the same value as CONFIG_SYS_CCSRBAR_DEFAULT,
and so CCSR will not be relocated.
Since CONFIG_SYS_CCSRBAR_DEFAULT is locked to a fixed value, multi-stage U-Boot
builds (e.g. NAND) are required to relocate CCSR only during the last stage
(i.e. the "real" U-Boot). All other stages should define
CONFIG_SYS_CCSR_DO_NOT_RELOCATE to ensure that CCSR is not relocated.
README is updated with descriptions of all the CONFIG_SYS_CCSRBAR_xxx macros.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add UTMI and ULPI PHY support for USB controller on qoriq series of
processors with internal UTMI PHY implemented, for example P1010/P1014
- Use both getenv() and hwconfig to get USB phy type till getenv()
is depricated
- Introduce CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY to specify if soc
has internal UTMI phy
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Acked-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The few tests that are Blackfin-specific have been migrated to common
code or been rewritten with the existing "bsp-specific" defines.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Flush the dcache before removing the TLB with caches enabled.
Otherwise this might lead to problems later on, e.g. while booting
Linux (as seen on ICON-440SPe).
Signed-off-by: Stefan Roese <sr@denx.de>
Change bd_t->bi_phy* arrays from 1 to 2 for PPC405EX since
405EX has 2 ethernet interfaces.
Signed-off-by: Bernhard Weirich <bernhard.weirich@riedel.net>
Signed-off-by: Stefan Roese <sr@denx.de>
Result of running the following command to address Wolfgang's
comment about camel case:
for file in `find . | grep '\.[chS]$'`; do perl -i -pe
's/(green|yellow|red|blue)_LED_(on|off)/$1_led_$2/g' $file; done
Discussion:
http://patchwork.ozlabs.org/patch/84988/
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Tuning some IO settings for better performance and power.
And consolidate all such IO settings at one place.
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
SDRAM init was not working on ES1.0 due to a programming
error. A pointer that was passed by value to a function
was set in function emif_get_device_details(), but the effect
wouldn't be seen in the calling function. The issue came
out while testing for ES1.0 because ES1.0 doesn't have any
SDRAM chips connected to CS1
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch contains the generic changes required after
change to generic API in the previous patch.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Convert all OMAP specific functions to use the common API
definitions in include/asm/gpio.h. In the process, made
few additional changes:
- Use -EINVAL consistently. -1 was used in many places.
- Removed one-liner static functions that were used only
once. Replaced the content as necessary.
- Combines implementation of functions omap_get_gpio_dataout()
and omap_get_gpio_datain(). To do so, new static function
_get_gpio_direction() was added.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
OMAP3: Add 37xx ESx revision numbers.
Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>
Signed-off-by: Howard D. Gray <howard.gray@matrix-vision.de>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Read directly from OMAP_GPIO_DATAOUT to get the output state of the GPIO pin
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Commit 21726a7 "Add assert() for debug assertions" caused build
warnings for all tegra2 based boards:
clock.c:36:1: warning: "assert" redefined
In file included from clock.c:29:
include/common.h:144:1: warning: this is the location of the previous definition
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Move the TIMER_ definitions before they are used in KS8695 timer.c code.
Fixes:
timer.c: In function ‘timer_init’:
timer.c:37: error: ‘TIMER_COUNT’ undeclared (first use in this function)
timer.c:37: error: (Each undeclared identifier is reported only once
timer.c:37: error: for each function it appears in.)
timer.c:38: error: ‘TIMER_PULSE’ undeclared (first use in this function)
Signed-off-by: Greg Ungerer <greg.ungerer@opengear.com>
Commit 17659d7 "Timer: Remove reset_timer_masked()" introduced a
static declaration for reset_timer_masked() which causes build errors:
timer.c:45: error: static declaration of 'reset_timer_masked' follows non-static declaration
include/asm/u-boot-arm.h:70: error: previous declaration of 'reset_timer_masked' was here
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Graeme Russ <graeme.russ@gmail.com>
Cc: Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
commit 0edf8b5b2f breaks
building on a different directory with the O= parameter.
The patch wil fix this issue, generating always asm-offsets.h before
the other targets.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Matthias Weisser <weisserm@arcor.de>
CC: Wolfgang Denk <wd@denx.de>
Since we are loading an executable image into memory we need flush it
out of the cache to possible maintain coherence on CPUs with split
instruction and data caches. We do this for other executable image
loading command.
On PowerPC once we do this we no longer need to explicitly flush the
dcache on multi-core systems in the BOOTM_STATE_OS_PREP phase. We now
treat the BOOTM_STATE_OS_PREP as a no-op to maintain backwards
compatibility with the bootm subcommand.
Signed-off-by: James Yang <James.Yang@freescale.com>
Signed-off-by: Diana CRACIUN <Diana.Craciun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'master' of git://git.denx.de/u-boot-coldfire:
ColdFire:Clean up the CONFIG_STANDALONE_LOAD_ADDR usage
ColdFire:Add mb for 5253 dram initialization
ColdFire:Define the DM9000 byteswap for M5253 board.
ColdFire:Update the env settings for several boards.
ColdFire:disable the NFS define for 52277 board.
ColdFire:Update the timer_init since it was unified.
ColdFire: Cleanup for partial linking and --gc-sections
ColdFire: Update compile flags for each CPUs
ColdFire:Fix the configuration broken for some boards.
* 'master' of git://git.denx.de/u-boot-arm: (145 commits)
beagleboard: enable HUB power on all variants of the BeagleBoard
dm3730: enable dpll5
ehci-hcd: Allow cleanups to happen gracefully on a timeout.
OMAP3: Add DSS driver for OMAP3
led: Remove state-saving of led for toggle functionality and add toggle option to led command
led: Fixed setting of STATUS_LED_BIT1 when led_name is 'all'
led: correct off/on locations in structure
led: added cmd_led to Makefile
BeagleBoard: fix LED 0/1 in driver
Corrected LED name match finding avoiding extraneous Usage printouts
BeagleBoard: config: updated default configuration
BeagleBoard: config: Enabled multibus support for I2C in configuration
BeagleBoard: config: add optargs/buddy/camera
BeagleBoard: config: increase command-line functionality
BeagleBoard: config: make mtest run
BeagleBoard: config: enable DSS
BeagleBoard: config: enable asix driver and dhcp
BeagleBoard: config: enable networking
BeagleBoard: config: decrease bootdelay to 2 seconds
BeagleBoard: config: use uImage.beagle for tftp
BeagleBoard: config: hardcode MAC for onboard SMSC
BeagleBoard: config: load kernel from MMC ext, not FAT
BeagleBoard: Configure DVI/S-video
BeagleBoard: Added userbutton command
BeagleBoard: turn off clocks in ehci_stop
USB: Remove __attribute__ ((packed)) for struct ehci_hccr and ehci_hcor
beagleboard: add support for xM revision C
beagle: pass expansionboard name in bootargs
OMAP: Remove omapfb.debug=y from Beagle and Overo env settings
OMAP3 Beagle Pin Mux initialization glitch fix
da850: modifications for Logic PD Rev.3 AM18xx EVM
da850: fix the channel number for EMAC teardown init
da850: add support for Spectrum Digital AM18xx EVM
da850: add support to wake up DSP during board init
da850: modify the U-Boot prompt string
da850: add NOR boot mode support
da8xx: add support for multiple PLL controllers
da850: indicate cache usage disable in config file
dm365: modify boot prompt from dm365 to dm36x
dm365: disable cache usage due to coherency issues
dm6446: disable cache usage due to coherency issues
OMAP3: Remove legacy mmc driver
devkit8000: Use generic MMC driver
TI OMAP3 SDP3430: Use generic MMC driver
AM3517 CraneBoard: Use generic MMC driver
OMAP3: pandora: Use generic MMC driver
OMAP3: Zoom2: Use generic MMC driver
OMAP3: Zoom1: Use generic MMC driver
OMAP3: DIG297: Use generic MMC driver
OMAP3: CM-T35: Use generic MMC driver
am3517evm: Use generic MMC driver
omap3evm: Use generic MMC driver
omap3:clock: check cpu_family before enabling clks for IVA & CAM
omap3:clock: configure GFX clock to 200MHz for AM/DM37x
OMAP3/4: Increase console I/O buffer size
PXA: vpac270: Remove re-defined CONFIG_SYS_TEXT_BASE
PXA: Fix CSB226, fix monitor length
PXA: Fix Lubbock, remove redundant parenthesis
armv7: cache: remove flush on un-aligned invalidate
armv7: stronger barrier for cache-maintenance operations
omap: enable caches at system start-up
arm: do not force d-cache enable on all boards
ORIGEN: Add MMC SPL support
ARMV7: Add support for Samsung ORIGEN board
i2c:gpio:s5p: Enable I2C GPIO on the GONI target
i2c:gpio:s5p: I2C GPIO Software implementation (via soft_i2c)
Tegra2: Use clock and pinmux functions to simplify code
Tegra2: Add additional pin multiplexing features
Tegra2: Add more clock support
Tegra2: Add microsecond timer function
ARM: remove broken "at91rm9200dk" board
ARM: remove broken "m501sk" board
ARM: remove broken "kb9202" board
ARM: remove broken "csb637" board
ARM: remove broken "cmc_pu2" board
ARM: remove broken "at91cap9adk" board
ARM: remove broken "voiceblue" board
ARM: remove broken "smdk2400" board
ARM: remove broken "sbc2410x" board
ARM: remove broken "netstar" board
ARM: remove broken "mx1fs2" board
ARM: remove broken "lpd7a40x" boards
ARM: remove broken "edb93xx" boards
ARM: remove broken "B2" board
ARM: remove broken "armadillo" board
ARM: remove broken "assabet" board
ARM: versatile: drop warnings
IMX: scb9328: drop warnings
MX31: imx31_litekit: make use of GPIO framework
MX31: mx31ads: make use of GPIO framework
MX5: mx51evk: make use of GPIO framework
MX35: mx35pdk: make use of GPIO framework
MX5: mx53loco: make use of GPIO framework
MX5: mx53evk: make use of GPIO framework
MX5: vision2: make use of GPIO framework
MX5: mx53smd: make use of GPIO framework
MX5: mx53ard: make use of GPIO framework
MX25: zmx25: make use of GPIO framework
MX5: efikamx: make use of GPIO framework
MX31: QONG: make use of GPIO framework
MX35: make use of GPIO framework for MX35 processor
MX5: make use of GPIO framework for MX5 processor
MX31: make use of GPIO framework for MX31 processor
MX25: make use of GPIO framework for MX25 processor
IMX: uniform GPIO interface using GPIO framework
MX: MX35 / MX5: uniform clock command with powerpc
MX35: MX35PDK: support additional RAM on CSD1
mx53: ddr3: Update DD3 initialization
ARM: MX51: PLL errata workaround
ARM: versatilepb : drop warnings due to double definitions
omap4: increase SRAM budget to fix build error
omap4: fix build warning due to signed unsigned comparison
mkimage: Fix 'Unknown OMAP image type - 5'
omap: fix gpio related build breaks
gpio:samsung: s5p_ suffix add for GPIO functions (C210_universal)
SMDKV310: MMC SPL: Remove unwanted dummy functions
SMDKV310: Fix undefined reference error
SMDKV310: Fix build error for smdkv310 board
gpio:samsung s5p_ suffix add for GPIO functions
mmc: S5P: Support DMA restarts at buffer boundaries
SMDKV310: Fix host compilation of mkv310_image
arm: fix bd pointer dereference prior initialization
arm, lib/board.c: use gd->ram_size instead of bd->bi_memsize
mx5: Remove CONFIG_L2_OFF and CONFIG_SYS_L2CACHE_OFF
MX31: removed warnings due to clock.h
integrator: convert to new build system
integratorcp: make the board compile
integratorap: remove hardcoded 32MB memory cmdline
...
The dram initialization sequence should be in order.
This patch add mb for the dram intialization code to make
sure the compiler do not disorder the code.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Introduce the --gc-sections for ColdFire platform and clean up the
corresponding lds file.
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Remove compiler version check for gcc 4.1 in config.mk.
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
which is used to provide 120MHz to USB EHCI
This allows EHCI to work on BeagleBoard XM
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
AHCLKR/UART1_RTS/GP0[11] pin needs to be configured for
NOR to work on Rev.3 EVM. When GP0[11] is low,
the SD0 interface will not work, but NOR flash will.
Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Signed-off-by: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
add support for DSP wake-up by default on DA850/OMAP-L138
during board initialization. Enable hwconfig environment and added
extra env setting through CONFIG_EXTRA_ENV_SETTINGS.
To prevent DSP from being woken up,set the environment variable as,
set hwconfig "dsp:wake=no"
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Modify clk_get() function in cpu file to work for
multiple PLL controllers.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
In case of AM3517 and AM3505 (which is OMAP3 varients), IVA2 and
ISP-CAMERA modules have been removed. So add check for cpu_family before
enabling clocks for these modules, else this impacts subsequent
power consumption and system suspend/resume functionality.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Ranjith Lohithakshan <ranjithl@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
AM/DM37x is another OMAP3 variant, where the GFX clock has been
boosted to 192MHz/200MHz. So fix the GFX_DIV value for this change.
HW Errata: Due to dependency of TV out clock of 54MHz, it is not
possible to configure GFX to 192MHz. So as per HW errats, the
recommended GFX clock is 200MHz (=CORE_CLK/2).
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Remove the flush of boundary cache-lines done as part
of invalidate on a non cache-line boundary aligned
buffer
Also, print a warning when this situation is recognized.
Signed-off-by: Aneesh V <aneesh@ti.com>
set-way operations need a DSB after them to ensure the
operation is complete. DMB may not be enough. Use DSB
after all operations instead of DMB.
Signed-off-by: Aneesh V <aneesh@ti.com>
c2dd0d4554 added dcache_enable()
to board_init_r(). This enables d-cache for all ARM boards.
As a result some of the arm boards that are not cache-ready
are broken. Revert this change and allow platform code to
take the decision on d-cache enabling.
Also add some documentation for cache usage in ARM.
Signed-off-by: Aneesh V <aneesh@ti.com>
This patch adds support for software I2C for GONI and Universal C210 reference targets.
It adds support for access to GPIOs by number, not as it is present,
by bank and offset.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Cc: Heiko Schocher <hs@denx.de>
These functions provide access to the high resolution microsecond timer
and tidy up a global variable in the code.
Signed-off-by: Simon Glass <sjg@chromium.org>
There was already a command to show the processor clocks
for PowerPC (clocks). For i.MX, the "clockinfo" command
was introduce. The patch sets the same command name used on
PowerPC.
A nasty and not needed newline is also dropped in the help for
the command.
Signed-off-by: Stefano Babic <sbabic@denx.de>
This is a port of the official PLL errata workaround from Freescale to
mainline u-boot.
The PLL's in the i.MX51 processor can go out of lock due to a metastable
condition in an analog flip-flop when used at high frequencies.
This workaround implements an undocumented feature in the PLL (dither
mode), which causes the effect of this failure to be much lower (in terms
of frequency deviation), avoiding system failure, or at least decreasing
the likelihood of system failure.
Signed-off-by: David Jander <david@protonic.nl>
This change is driven by need of general gpio_* functions,
which as their parameter are accepting the GPIO pin number, NOT
block and pin.
This makes the code alike to omap, and allows for using more
generic frameworks (e.g. software I2C).
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
gd->bd pointer has been used prior been initialized.
Move the relevant code after the initialization.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
This deletes the integrator split_by_variant.sh script and
defines a number of unique board types for the core modules
that are meaningful to support for the Integrator AP/CP, i.e.
the ones that did not just say "unsupported core module" in
split_by_variant.sh. If more core modules need to be supported
they are easy to add.
We delete all the old cruft in Makefile and MAKEALL that was
working around the old way of building boards. We create a
unique config file per board to satisfy the build system, but
they are just oneliners that include the existing
integratorap.h and integratorcp.h configs.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In some cases (e.g. bootm with a elf payload which is already at the right
position) there is a in place copy of data to the same address. Catching this
saves some ms while booting.
Signed-off-by: Matthias Weisser <weisserm@arcor.de>
The issue is found when calling flush_cache() with zero "size" argument.
The bound of loop is miscalculated in this case and flush_cache() enters
a wrong flushing loop.
Signed-off-by: Yao Cheng <saturdaycoder@gmail.com>
Cc: Shinya Kuribayashi <skuribay@pobox.com>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
Some SH have MMC controller. So, if we need it, we have to call
the mmc_initialize().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Only the optimization of sh2 had been supported up.
This adds the optimization of sh2a.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
SH2A toolchains often only provide an fdpic version of libgcc. This
can't be used with bare-metal software like U-Boot, so this patch
provides the necessary functions extracted from libgcc.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The rsk7264 (also know as rsk2+sh7264) is an SH2A based board
with 64MB NAND flash and 64MB SDRAM. It is very similar to the
rsk7203 board.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
There was a mix of UTF-8 and ISO-8859 files in the U-Boot source
tree, which could cause issues with the patchwork review system.
This commit converts all ISO-8859 files to UTF-8.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
The U-Boot Design Principles[1] clearly say:
Initialize devices only when they are needed within U-Boot, i.e. don't
initialize the Ethernet interface(s) unless U-Boot performs a download
over Ethernet; don't initialize any IDE or USB devices unless U-Boot
actually tries to load files from these, etc. (and don't forget to
shut down these devices after using them - otherwise nasty things may
happen when you try to boot your OS).
So, do not initialize and read the sensors on startup.
Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Holger Brunck <holger.brunck@keymile.com>
* 'master' of git://git.denx.de/u-boot-arm:
drivers/rtc: add Marvell Integrated RTC
Armada100: Add Board Support for Marvell GuruPlug-Display
Armada100: MFP macro naming correction
arm: auto gen asm-offsets.h for mb86r0x
spear: fix build errors for spear3xx/spear600 platforms
cosmetic: arm: lib/board.c: Coding Style cleanup
ARM: versatile: fix board support
SMDKV310: Enable device tree support
SMDKV310: MMC_SPL: Fix building when using "make O="
arm: a320: enable tagged list support
arm: a320: fix multiline comment style
ARMv7: u8500_href: Add missing header to fix compiler warning
Removed unused define, CONFIG_ARMV7.
avr32: add grasshopper (ICnova AP7000) board
AT91/SPI: fix atmel_dataflash_spi.c to allow building without warnings
MAKEALL: remove AT91 boards that are in boards.cfg
AT91: Makes AT91SAM9263-EK build correctly against u-boot-atmel/master
AT91: Makes AT91SAM9263 SoC build correctly against u-boot-atmel/master
AT91: Board fix for AT91SAM9261-EK
AT91: SoC fix at91sam9261_matrix.h
AT91: Makes AT91SAM9RL-EK build correctly against u-boot-atmel/master
AT91: Makes AT91SAM9RL SoC build correctly against u-boot-atmel/master
AT91: change common at91sam9261 files to compile with new scheme
AT91: fix mistake in at91sam9260_devices.c(spi1_hw_init)
a/a/c/arm920t/at91/reset.c: drop obsolete CONFIG_AT91RM9200_USART
README: fix arm920t/at91 path
net/eth.c: drop obsolete at91rm9200 support
README.at91-soc: remove AT91(RM9200) joining notice
a/a/c/arm920t/cpu.c: remove CONFIG_AT91_LEGACY warning
MAKEALL: remove obsolete at91rm9200 soc
ARM: remove obsolete at91rm9200
omap4: clock init support for omap4460
omap4: support TPS programming
omap: reuse omap3 gpio support in omap4
omap4: sdram init changes for omap4460
omap4: add omap4460 revision detection
mkimage: Add OMAP boot image support
omap: add MMC and FAT support to SPL
omap: add basic SPL support
armv7: start.S: fixes and enhancements for SPL
omap4: automatic sdram detection
omap4: calculate EMIF register values
omap4: add sdram init support
omap4: add clock support
omap4: add OMAP4430 revision check
omap4: cleanup pin mux data
omap4: utility function to identify the context of hw init
DA8xx: fix LPSC constants
DA8xx: switch an enum to defines for consistency
DA8xx: add MMC/SD controller addresses
DaVinci EMAC: declare function for all DA8xx CPUs
DA8xx: add generic GPIO driver
DaVinci: rename gpio_defs.h to gpio.h
omap3evm: eth: Include functions only when necessary
omap3evm: Update ethernet reset sequence for Rev.G board
omap3evm: eth: split function setup_net_chip
omap3: Include array definition only when it is used
omap730p2: fix build breaks
omap2420h4: fix build breaks
omap1610inn: fix build breaks
omap1510inn: fix build breaks
omap5912osk: fix build breaks
omap1610h2: fix build breaks
The SHARP LQ084S3LG01 is a TFT LCD used on the P1022DS (revision "C") board.
This device only supports 800x600 resolution, so if that resolution is selected,
assume that this is the device. The device is attached to the LVDS port
on the P1022DS board.
The existing 800x600 entry (for the PDM360NG board) is actually 800x480,
so we fix that. To support two different 800x resolutions, the Y-resolution
is now passed to fsl_diu_init() and both values are used to pick the proper
fb_videomode structure.
The data for the 800x600 video mode is originally from Jiang Yutang.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Jiang Yutang <b14898@freescale.com>
This driver can be used for kirkwood SoCs by enabling CONFIG_RTC_MV. Tested on
Global Scale Technologies Dreamplug.
Signed-off-by: Jason Cooper <u-boot@lakedaemon.net>
Rework for AT91SAM9263 SoC, makes it build again.
Based on the work for AT91SAM9260-EK.
Signed-off-by: Hong Xu <hong.xu@atmel.com>
Signed-off-by: Reinhard Meyer <uboot@emk-elektronik.de>
Rework for AT91SAM9RL SoC, makes it build again.
Based on the work for AT91SAM9260-EK.
V4: US->USART, cosmetics
Signed-off-by: Hong Xu <hong.xu@atmel.com>
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
Bits 0..3 in cs_mask = CS0..CS3 in SPI mode require it to be peripheral
Bits 4..7 in cs_mask = CS0..CS3 in GPIO mode require it to be output
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
The CONFIG_AT91RM9200_USART is an remnant of
18ed5e9550 which deleted the
at91rm9200_usart driver.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
The CONFIG_AT91_LEGACY warning became obsolete due to complete removal of
at91rm9200 arch code in arm920t.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
The big "ARM: remove broken boards" series deletes all boards using
obsolete arm920t/at91rm9200 arch code. Therefore we can safely remove
this code now.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
TPS62361 is the new power supply used in OMAP4460 that
supplies vdd_mpu.
VCORE1 from Phoenix supplies vdd_core and VCORE2 supplies
vdd_iva. VCORE3 is not used in OMAP4460.
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
- Add mkimage support for OMAP boot image
- Add support for OMAP boot image(MLO) generation in the new
SPL framework
Signed-off-by: John Rigby <john.rigby@linaro.org>
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
- Add MMC raw and FAT mode boot support for OMAP
- Provide a means by which parameters passed by ROM-code
can be saved in u-boot.
- Save boot mode related information passed by OMAP4 ROM-code
and use it to determine where to load the u-boot from
- Assumes that the image has a mkimage header. Gets the
payload size and load address from this header. If the
header is not detected assume u-boot.bin as payload
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
- Provide alternate implementations of board_init_f()
board_init_r() for OMAP spl.
- Provide linker script
- Initialize global data
- Add serial console support
- Update CONFIG_SYS_TEXT_BASE to allow for SPL's bss and move
it to board config header from config.mk
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
- Allow SPL to have .bss disjoint from rest of the image
- Allow for .bss setup in CONFIG_SPL_BUILD case too.
- Take care of the special case where relocation offset = 0.
- Compile out exception handling code and install a simpler
vector
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Identify SDRAM devices connected to EMIF automatically:
LPDDR2 devices have some Mode Registers that provide details
about the device such as the type, density, bus width
etc. EMIF has the capability to read these registers. If there
are no devices connected to a given chip-select reading mode
registers will return junk values. After reading as many such
registers as possible and matching with expected ranges of
values the driver can identify if there is a device connected
to the respective CS. If we identify that a device is connected
the values read give us complete details about the device.
This along with the base AC timings specified by JESD209-2
allows us to do a complete automatic initialization of
SDRAM that works on all boards.
Please note that the default AC timings specified by JESD209-2
will be safe for all devices but not necessarily optimal. However,
for the Elpida devices used on Panda and SDP the default timings
are both safe and optimal.
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Calculate EMIF register values based on AC timing parameters
from the SDRAM datasheet and the DDR frequency rather than
using the hard-coded values.
For a new board the user doen't have to go through the tedious
process of calculating the register values. Instead, just
provide the AC timings from the device data sheet as input
and the driver will automatically calculate the register values.
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Add support for:
1. DPLL locking
2. Initialization of clock domains and clock modules
3. Setting up the right voltage on voltage rails
This work draws upon previous work done for x-loader by:
Santosh Shilimkar <santosh.shilimkar@ti.com>
Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
- separate mux settings into essential and non essential parts
- essential part is board independent as of now(so move it
to SoC directory). Will help in having single SPL for all
boards.
- Non-essential part(the pins not essential for u-boot to function)
need to be phased out eventually.
- Correct mux data by aligning to the latest settings in x-loader
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The basic hardware init of OMAP4(s_init()) can happen in 4
different contexts:
1. SPL running from SRAM
2. U-Boot running from FLASH
3. Non-XIP U-Boot loaded to SDRAM by SPL
4. Non-XIP U-Boot loaded to SDRAM by ROM code using the
Configuration Header feature
What level of hw initialization gets done depends on this
context. Add a utility function to find this context.
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Some of the LPSC constants were incorrect, and some were missing. This
commit fixes the incorrect constants (which were not used anywhere in
the tree) and adds all constants for both DA830 and DA850, as per the
TI datasheets.
Signed-off-by: Laurence Withers <lwithers@guralp.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
There are two main sets of LPSC constants, depending on the processor
family. The DA8xx constants were given in an enum whereas the non-DA8xx
constants were preprocessor defines. This commit switches the DA8xx
constants to defines for consistency.
Signed-off-by: Laurence Withers <lwithers@guralp.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The function davinci_emac_mii_mode_sel() is defined in
board/davinci/common/misc.c for any DA8xx CPU which has
CONFIG_DRIVER_TI_EMAC enabled. However, the prototype was only being
declared in <include/asm/arch/davinci_misc.h> for the DA850 EVM board.
This patch declares it for all DA8xx CPUs where CONFIG_DRIVER_TI_EMAC
is enabled.
Signed-off-by: Laurence Withers <lwithers@guralp.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Add a generic GPIO driver for the DaVinci DA8xx processors. It is turned
on by defining CONFIG_DA8XX_GPIO and fulfills the generic GPIO interface
specified in <asm/gpio.h> . The driver has support for both manipulating
GPIO pins as well as automatically configuring the pin multiplexor
registers to set the pin function to GPIO.
Signed-off-by: Laurence Withers <lwithers@guralp.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
In preparation for a generic GPIO driver for the DA8xx processors,
rename <asm/arch/gpio_defs.h> to <asm/arch/gpio.h> and fix up all files
which include it.
Signed-off-by: Laurence Withers <lwithers@guralp.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The array of strings corresponding to cpu revision is
used only when CONFIG_DISPLAY_CPUINFO is selected - in
the function print_cpuinfo().
Enclose definition of this array in #ifdef...#endif for
the same.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* 'master' of git://git.denx.de/u-boot-blackfin:
Blackfin: jtag-console: fix timer usage
Blackfin: switch to common display_options()
Blackfin: serial: move early debug strings into .rodata section
Blackfin: adi boards: also set stderr to nc with helper
Blackfin: update anomaly lists to latest public info
Blackfin: serial: convert to bfin_{read,write} helpers
Blackfin: split out async setup
Blackfin: adi boards: enable pretty flash progress output
Blackfin: drop unused dma.h header from start code
Blackfin: portmux: allow header to be included in assembly files
Blackfin: cm-bf537e/cm-bf537u/tcm-bf537: enable mmc_spi support
Blackfin: cm-bf537e/cm-bf537u/tcm-bf537: update network settings
Blackfin: sync MMR read/write helpers with Linux
Blackfin: gpio: optimize free path a little
Blackfin: post: setup default CONFIG_SYS_POST_WORD_ADDR
Blackfin: uart: fix printf warning
Blackfin: add init.elf helper code
Blackfin: dont reset SWRST on newer bf526 parts
Blackfin: adi boards: enable multi serial support by default
Blackfin: uart: add multiple serial support
Blackfin: uart: move debug buffers into local bss
Clean up some duplicated prototype declarations.
Get rid of now useless AVR32 initcalls.h file.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Albert Aribaud <albert.aribaud@free.fr>
Cc: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Graeme Russ <graeme.russ@gmail.com>
Also remove bogus comment.
Signed-off-by: Zhong hongbo <bocui107@gmail.com>
Changed commit message
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Albert Aribaud <albert.aribaud@free.fr>
Currently the cache operation mode is hard-coded to
CONF_CM_CACHABLE_NONCOHERENT. This is not appropiate for CPUs or SOCs
which operate at a different mode.
This patch makes the cache operation mode configurable via board config.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Acked-by: Thomas Langer <thomas.langer@lantiq.com>
Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
This define is a board-specific config option and should be
renamed to follow the U-Boot naming convention. Additionally,
add an explaining comment for this option.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Acked-by: Thomas Langer <thomas.langer@lantiq.com>
Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
We used <usb.h> for USB_MAX_DEVICE. However this requires we actual
build in support for USB into u-boot (which should not be required for
device tree fixup).
At this time no FSL SoC that utilizies this code (83xx/85xx) has more
than 2 USB controllers. So we replace USB_MAX_DEVICE with a local
define FSL_MAX_NUM_USB_CTRLS.
If/when a device shows up with more than 2 controllers we can easily
bump this value or refactor into a proper define per SoC.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
to make USB2 worked in gadget mode, we need to set it's 'dr_mode' to
'peripheral' in hwconfig, but driver starts scan from 'usb1', it'll break
out if it cannot find 'usb1', so drop the 'else' clause to make driver scan
all the 'usbx'.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Introduce ft_verify_fdt(), a function that is called after the device tree
has been fixed up, that displays warning messages if there is a mismatch
between the physical addresses of some devices that U-Boot has configured
with what the device tree says the addresses are.
This is a particular problem when booting a 36-bit device tree from a
32-bit U-Boot (or vice versa), because the physical address of CCSR is
wrong in the device tree. When the operating system boots, no messages are
displayed, so the user generally has no idea what's wrong.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Current code would print RAM size information like this:
DRAM: DDR: 256 MiB (DDR1, 64-bit, CL=2, ECC off)
Turn a number of printf()s into debug() to get rid of the redundant
"DDR: " string like this:
DRAM: 256 MiB (DDR1, 64-bit, CL=2, ECC off)
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
At some point we broke the detection of e500v1 class cores. Fix that
and simply the code to just utilize PVR_VER() to have a single case
statement.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix up the device tree property associated with the Flexcan clock
frequency. This property is used to calculate the bit timing parameters
for Flexcan.
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This provides a function that will override the weak function
flush_icache to let 85xx boards to flush the icache
cc: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Matthew McClintock <msm@freescale.com>
The P2040/P2040E have no L2 cache. So we utilize the SVR to determine
if we are one of these devices and skip the L2 init code in cpu_init.c
and release. For the device tree we skip the updating of the L2 cache
properties but we still update the chain of caches so the CPC/L3 node
can be properly updated.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We add XAUI_FM1 into the SERDES tables for P2041[e] devices. However
for the P2040[e] devices that dont support XAUI we handle this at
runtime via SVR checks. If we are on a P2040[e] device the SERDES
functions will behave as follows:
is_serdes_prtcl_valid() will always report invalid if prtcl passed in is
XAUI_FM1.
serdes_get_prtcl() will report NONE if the prtcl in the table is set to
XAUI_FM1.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
